ABBEY ARTSTONE
Construction ProductsOur range of standard architectural masonry products
CONSTRUCTION PRODUCTSOur range of standard architectural masonry products
01TECHNICAL DATA
02CILLS & BAY CILLS
08HEADS, KEYSTONES & LABEL MOULDING
16JAMBS, MULLIONS & JAMB BLOCKS
19WINDOW & DOOR SURROUNDS
24ASHLAR & QUOINS
27PLINTH & STRING COURSE
32CORNICE, EAVES, DENTILS & CORBELS
36COPINGS
42PIERS, CAPS & SPHERES
47GABLE VENTS, NAMESTONES & CHIMNEY CAPS
HEALTH, SAFETY & WELFARE
The colours shown are indicative and colour samples should be requested fora true representation of the products colour
Our Architectural masonry blocks and quoins are manufacturedin accordance with BS6073 parts 1 & 2:1981 in two part or homogenous semi dry or wet cast mix. Using natural occurring aggregates, sand, Portland cement and an integral waterproofer, pigments are added where necessary.
Cast Stone Dressings When tested in accordance with BS1881:Part 116: 1983 and BS1217:1997 and the United Kingdom cast Stone Association, the cast stone was tested over three 150mm cubes giving an average crushing strength well in excess of 25KN/mm2.
Ashlar Blocks And QuoinsWhen tested in accordance with BS1881:Part 116: 1983 and BS6073: parts 1 & 2:1981, the cast stone was tested over ten samples of blocks at a size of 440x215x100mm giving an average strength in excess of 10KN/mm2.
All cast stone heads and cills are decorative and are not designed to be load bearing. Load bearing products can be manufactured in a wet cast method of manufacture and are available in such a material upon request.
Quoins, Plinths and String Courses can be used in load bearing situations when used in compression.
All units are reinforced where necessary with handling reinforcement.
TECHNICAL DATA
COMPOSITION
COMPRESSIVE STRENGTH
STRUCTURAL USE
DENSITY
The typical average density of stone from stock architectural masonry is 2150kg/m3
DRY SHRINKAGEThe average dry shrinkage of three specimens sampled and tested in accordance with BS6073:Part 1 was as follows:Face Mix <0.04% Backing Mix <0.06%
WEATHERINGMany factors influence the way cast stone weathers, such as design, exposure, climate and surrounding. All pigments used are colourfast and durable and conform to BS1014. Stone From Stock architectural dressings will weather in a similar manner to natural stone, when exposed to similar conditions.
CEMENTITIOUS EFFLORESCENCE
As with all reconstructed stone and cement based products there is the possibilitythat the temporary phenomenon known as efflorescence will occur causing lightening of colour. This will reduce over a period of time with natural weathering.
The contractor shall ensure that health, safety and welfare measures required or byvirtue of the provision of any enactment or regulation or the working rules of the industry are complied with.
Calder (M03), BuffThis is the STOCK colour
Portland
Grey
McDonald Red
M08
Bath
COLOURS
The colours above are available to order only
CONSTRUCTION PRODUCTSOur range of standard architectural masonry products
Based in Keighley, West Yorkshire Abbey Artstone Limited provides the highest quality architectural masonry products.We supply contracts throughout the UK from large residential and commercial developments to small extension or gardenwalls. Whatever your needs, Abbey Artstone has the experience to supply.
Abbey Artstone provides four main product types; Semi dry cast stone products,Wetcast reinforced stone products. Glass Reinforced Cement (GRC) and Glass Reinforced Plastic (GRP). From these four base materials we can provide a wide range of masonry products to suit your needs.
Semi Dry is perhaps the most commonly used cast stone in the house building industry as a cost effective alternative to natural stone. It is a versatile product used for many applications which includes (but is not limited to) window surrounds, copings and pier caps, ballustrade, bulls eye windows, quoins, corbels, ashlar blocks, vents, datestones, keystones and much more.
01 TECHNICAL DATA
ABBEY ARTSTONE
CILLS & BAY CILLS
02CILLS AND BAY CILLS
ABBEY ARTSTONE LIMITED
03 STANDARD CILLS
ABBEY ARTSTONE LIMITED - MDL/C/01
E
A
B
D
E
100/150
C
A
C
Cill Components Are Designed To Accept Standard Win dow UnitsBS5628 Part 3 1985Fixing Of Cill To Be Generally In Accordance With
Isometric
Part Elevation
Size Required 100mmOr 150mm
Please State Stooling
BS5628 Part 3 1985
Cill Components Are Designed To Accept Standard Win dow Units
Traditional Cill
G
* Maximum Length In One Unit 1200mm
Fixing Of Cill To Be Generally In Accordance With
Isometric
G
Standard Cill
125 200175150150E
TCL1 TCL3TCL2
Section
Option ** C=215mm
G
F
E 150
1010
150
10
200
D
C
A
B
140
100100
65
100
140
60
100100
60
150
60
Part Elevation
Section
Please State Stooling
Or 150mmSize Required 100mm
* *
Option ** C=215mm
G
10F 1010 10 10
65C
40D
B 100
A 50
140 140140140
100100 100 100
65
150100 100
50 65
150
65
CL1* **
CL4**
CL2 CL3**
CL5
F
F
To Suit
To Suit
B
D
100./150
04STANDARD CILLS
ABBEY ARTSTONE LIMITED - MDL/C/02
100/150
B
D
B
C
A
C
A
FE
DE
BCL1I
BCL2I
Part Elevation
2110
* Cast In Two Units
BCL1D
BCL2D
Structural488
Opening300 630 915
BCL1B
BCL2B
CillBCL1AType
CillType BCL2A
BCL1C
BCL2C
1200 1340 17701540
BCL1G
BCL2G
BCL1FBCL1E
BCL2E BCL2AF
BCL1H
BCL2H
Bullnose Cill
G
Isometric
Section
OpeningStructural
G
Maximum Length 1500mm
Isometric
* Section
F
Slip Cill
1010101010E
1200 r/h
BCL1N
BCL2N
2340 630 l/h 1200 l/h630 r/h
BCL1K*BCL1J
*BCL2J BCL2K
BCL1MBCL1L
BCL2MBCL2L
100G
150
100
150
BCL1
F
E
C
D
A
B
140140
35
6565
20
197150
10065
150100
BCL2
Option ** C=215mm
F To Suit
*
175
SCL4
65
140
100
C
D
B
100100 100
125
140
150
65 140
150
A
***SCL2
5050
SCL1
65
SCL3
100
140
200
***SCL5
65
05 FEATURE CILLS
ABBEY ARTSTONE LIMITED - MDL/C/03
C
B
A
D
A
B
10
D
C
60
C 30
D
A
B
304010
1010
C
D
B
A
0.17
1
600.
114
60
Isometric
Section
Isometric
E
Standard Moulded Cill (Type .1.)
Traditional Mouldded Cill (Type .1.)
E
Section
Isometric
Traditional Moulded Cill (Type .2.)
Section
Isometric
Standard Moulded Cill (Type .2.)
E
E
Section F
D
A
C
B
100 Or 150mm
200150 175
65 65 65
150
140140 140
100 150
MCL3MCL2MCL1
A
E
D
C
B
200150
140140
100100
MTCL1 MTCL2
6060
Please Specify
To Suit
200
E
D 150 175
MCL6
150
140
6565 65A
C
B
140 140
100 150
MCL4 MCL5
To Suit
A
200
To Suit
100
140
E
150D
140C
100B
MTCL4
60
MTCL3
60
E To Suit
F
F
F
F
F Please Specify100 Or 150mm
F
F
F
F
F Please Specify100 Or 150mm
F100 Or 150mmPlease Specify
06BAY WINDOW CILLS
ABBEY ARTSTONE LIMITED - MDL/BC/01
10
10
DC
B
A
A
B
B
C
Y/N
A
DimensionsBrickwork
Required
RefCill
EndsStooling
BrickworkDimensions
Required
B
Cill
EndsStooling
Ref
C
A
Y/N
D
E
Bay BrickworkDimensions
Bay BrickworkDimensions
10
45° Splayed Bay Cill
90° Splayed Bay Cill
Isometric
Brickwork Plan
DimensionsBay Brickwork
DimensionsBay Brickwork
10
10
10
Bay Window Units Come In Three To Four Units Depending on length
Brickwork Plan
Isometric
07 BAY WINDOW CILLS
ABBEY ARTSTONE LIMITED - MDL/WC/01
10
CA
B
B
A
Water
Delete As Necessary
BarGroove
Y/N
BrickworkDimensions
Required
B
Cill
EndsStooling
Ref
C
A
Y/N
D
Bay BrickworkDimensions
Bay BrickworkDimensions
10
45° Splayed Bay Cill
90° Splayed Bay Cill
Isometric
Brickwork Plan
*
DimensionsBay Brickwork
DimensionsBay Brickwork
10
10
Bay Window Heads & Complete Surrounds
* Specify Cill Type Required Refer To MDL/C/01-02Bay Window Units Come In Three To Four Units Depending on length
Please Contact Our Sales Office For Further Details
Brickwork Plan
Isometric
Opp HandAs Dwg / Or
As Dwg / OrOpp Hand
Delete As NecessaryGroove
EndsStooling
BarWater
* RefCill
Y/N
Y/N
RequiredDimensionsBrickwork
C
B
A
Bay Window Heads & Complete Surrounds
* Specify Cill Type Required Refer To MDL/C/01-02Bay Window Units Come In Three To Four Units Depend ent On Length
Please Contact Our Sales Office For Further Details
ABBEY ARTSTONE
HEADS, KEYSTONES & LABEL MOULDING
08HEADS, KEYSTONES & LABEL MOULDING
ABBEY ARTSTONE LIMITED
09 STANDARD HEADS
ABBEY ARTSTONE LIMITED - MDL/H/01
B
A
C
D
B
AA
150100B
140
PH1
A 140
PH2
100100
290
PH4
215
PH3
Isometric
Isometric
Isometric
150100B
25
25
D
C
25
25
140
CH1
A 140
CH2
100100
25
25
25
25
290
CH4
215
CH3
100100B
50
D
C 100
140
SH1
A 140
SH4
100100
10050
215
SH5
215
SH2
E To Suit
E
C To Suit
To SuitD
Section
Section
Section
C
To Suit
To Suit
Plain Head
Chamfered Head
Splayed Head
290290
50
100
100
100
SH3 SH6
B=125mm For Use WithRender Please SpecifyIf Required
Render Please SpecifyB=125mm For Use With
If Required
Option
Option
B=125mm For Use WithRender Please SpecifyIf Required
Option
10FEATURED HEADS
ABBEY ARTSTONE LIMITED - MDL/FH/01
0.07
10.07
10.
071
0.029
0.21
40.
214
0.029
B
A
B
A
B
A
B= 125mm For UseWith Render PleaseSpecify If Required
Option
B= 125mm For UseWith Render PleaseSpecify If Required
Option
Option
C
To Suit
C
C
To Suit
C
Specify If RequiredWith Render PleaseB= 125mm For Use
Optional With Or Without Circular IndentsOther Designs Can Be Made To Order
FH9FH8
100100
150150
100
215 290
FH7
100B
150C
100
A 140
100
FH6FH5
100100
150150
100
215 290
FH4
100B
150C
100
A 140
100
100
150
100
150150
100
C
C
Half Round Feature Head
Eliptical Feature Head
Feature Head
To Suit
Section
Section
Section
C
Isometric
Isometric
Isometric
FH3
290
100
FH2
215A
FH1
140
B 100 100
11 KEYSTONE HEADS
ABBEY ARTSTONE LIMITED - MDL/H/02
A
D
B C
E
FG
D
A
C
B
100B
215
PKS1
A
Isometric
Isometric
Isometric
C
H
Section
Part Elevation
Section
Part Elevation
With Square Ends
Part Elevation
D
E
F
G
10
75
300
150
50
F 50
E
D
150
300
B
C
A
100
75
215
FKS1
With Splayed Ends
With Splayed Ends
With Square Ends
H
G
G
Projecting Keystone Head
Flush Keystone Head
GSuit
To
HTo
Suit
75
300
150
Suit
100
To
PKS2
100
215
10
Suit
To
215
100
300
150
100
75
FKS2
B=125mm For UseWith Render Please
Specify If Required
Specify If RequiredWith Render PleaseB=125mm For Use
Isometric
12FEATURE KEYSTONE HEADS
ABBEY ARTSTONE LIMITED - MDL/H/03
19510 10
140 1010
1021710
0.286
0.214
0.20
060
850.
029
0.21
40.
614
0.286
0.071
0.20
0
0.071
50
30
0.214
0.61
4
18
18
150
150
OpeningStructural
150
150
OpeningStructural
Section
Part Elevation
Part Elevation
Section
2 5R
25R
Isometric
Isometric
Rosedale Keystone Head
Kirkstall Keystone Head
13 ARCHED HEADS & ARCHED KEYSTONE HEADS
ABBEY ARTSTONE LIMITED - MDL/A/01
A Structural Opening
50
30
195
140
10
Structural OpeningA
D
50
E
15
D
100
E
C
25
7560
100D
140E
25C
75B
140A
100D
215E
25C
75B
140A
75B
140A
Arch TypeA=140mm
Structural
KA1
488Opening
KA2
630
KA4
1200
KA3
915
StructuralOpening
PKA3PKA2
488
PKA1
630 915 1200
PKA4
OpeningStructural
PA7PA6
488
PA5
915630 1200
PA8
Elevation Section
SectionElevation
SectionElevation
Keystone Detail
Section
Keystone Arch
Projecting Keystone Arch
Plain & Chamfered Arch
C 25
A=140mmArch Type
PA3PA2PA1 PA4
25
75
215
100
290
25
75
215
10
10
10
OpeningStructural
KA8KA7
488 630
KA9 KA10
915 1200
A=215mmArch Type
KA5
1500
KA6
1700
KA11
1500
KA12
1700
25
215
100
215
75
Arch TypeA=140mm PKA5
1500
PKA6
1700StructuralOpening
Arch TypeA=215mm PKA9
915488 630
PKA7 PKA8
15001200 1700
PKA11PKA10 PKA12
D 100100
A=215mmArch Type
PA10
1500
PA9
PA12
1770
PA11Arch TypeA=140mm
Arch TypeA=215mm
StructuralOpening
CA13
488 630
CA14
915
CA15 CA18
1500
CA16
1200
CA20
1770
CA9 CA10 CA11 CA17CA12 CA19
14KEYSTONES
ABBEY ARTSTONE LIMITED - MDL/K/01
A
CD
F
E
B
HG 21
5
15
1050
1060
10025
10
F GH
C
290
50
B
100
E
25100
A
10
D
15
A D
C
B E
F
A 102 48
B
C 10218
3020
147
18
12210
Elevation
Splayed Keystone
Section
D 215
F 10
70E
A
B
300
120
C 280
KS6
E 5050E
KS
140
100
80
184
290
250
Elevation Section
E
F
B
C
D
Chamfered Keystone
Elevation
3
A
Section
F
G
H
Elevation Section
140
250
80
215
100
B 215
C 80
Moulded Keystone4
KS
184
10
10
70
KS
A
5
160
F
G
H
70
10
10
Rosedale Keystone
B
D
C
A
Kirkstall Keystone
160
70
215
KS
215
1
B 160
D
C 290
70
A
2KS
237
Elevation Section
15 LABEL MOULDING
ABBEY ARTSTONE LIMITED - MDL/L/01
C
B
A
D
A
BB
C C
D D
DD
B B
10025
65
A
CC
B B
125
140
290
*140
C
D
1000
600
A
B
C 130
B
A
1000
1000
215
1000
1000
Elevations
Section
Section
Elevations
Section
Elevations
Moulded Label Mould
Chamfered Label Mould
Radius Label Mould
D *140
*140
Standard Lengths Of Label Mouldings
Can Be Used For String Courses If Required
10
* Available To Suit, 140215 & 290mm Deep
Left Hand Return Unit Right Hand Return Unit
Straight Unit
Left Hand Return Unit Right Hand Return Unit
Straight Unit
Angle UnitLeft Hand Right Hand
Angle Unit
Right HandAngle Unit
Left HandAngle Unit
Heads
215 & 290mm DeepHeads
* Available To Suit, 140
215 & 290mm DeepHeads
* Available To Suit, 140Angle UnitLeft Hand
Angle UnitRight Hand
Left Hand Return Unit Right Hand Return Unit
25
45
30
30
35
43
11
10030
65
ABBEY ARTSTONE
JAMBS, MULLIONS & JAMB BLOCKS
16JAMBS & JAMB BLOCKS
ABBEY ARTSTONE LIMITED
17 JAMBS & MULLIONS
ABBEY ARTSTONE LIMITED - MDL/JM/01
A
B
A
B
B
A
EF
G H
EF
G
BA
H G
B
A
D
EF G
B
DA
150100 150B
Isometric
Isometric
Flush Jamb
D
Isometric
Plan Section
Flush Mullion
Plan Section
33F
105G
50
10
D
E
150A
B 150
FJ1
IsometricPlan Section
H
B
A
Plan Section
E
H
33F
50G
50
10
D
E
150
150
A
B
FJ1
CM6CM4 CM5
10050 100
150
150
100
100
150
100
75 75
75 125
125
125
Isometric
Chamfered Jamb
Plain Jamb
PJ1
100
100
Chamfered Mullion
IsometricTable Applicable To All Details
A
900C 750 1050 1200
C
C
Plain Mullion
B
Plan Section
A
CJ5CJ4 CJ6
100100 150
15001350
215 215150150
100 150
PJ4 PJ5PJ3PJ2
150100
PM2
100
150B 100
A 100
PM1
150
150
PM3
215
PJ4
100
215
PJ5
150
* Chamfer Stopped Top & BottomIf Required Please Specify
Plan Section
C
C
D
C
C
18JAMB BLOCKS
ABBEY ARTSTONE LIMITED - MDL/JB/01
B
A
C
D
0.04
8
A
BC
D
0.04
8
0.048
0.04
8
0.04
8
B
A
C
D
0.04
8
B
A
B
C
B
A0.04
8
B
C
4 5 °
4 5 °
4 5 °
100
140
C
D
100
215
JB
100
150
A
B
100
225
100
330
100
290
1 2
JB
3
JB
290
100
140
100
D
C
215
100
330
100
64 5
150
100
B
A
225
100
JB JBJB
9
100
330
100
290
100
140
C
D
100
215
100
150
7
A
B
100
225
8
JB JB JB
Plan Section
Vertical Section
Plan Section
Isometric
Isometric
Isometric
Plan Section
Plain Jamb Block
Chamfered Jamb Block
Large Chamfered Jamb Block
Vertical Section
Vertical Section
Isometric Stop End
Isometric Stop End
Traditional Jamb Block
Traditional Plinth Block
Plan Section
Plan Section
Elevation
Elevation
Isometric
Isometric
100 100 100C
140D 290215
100
7
JB
150
A
B
100 100
330225
98
JB JB
100 100 100C
140D 290215
100
7
JB
150
A
B
100 100
330225
98
JB JB
ABBEY ARTSTONE
WINDOW & DOOR SURROUNDS
19 WINDOW & DOOR SURROUDNS
ABBEY ARTSTONE LIMITED
20PLAIN SURROUNDS WITH LABEL MOULDING
ABBEY ARTSTONE LIMITED - MDL/WD/01
BB
A A
A
B
100
A
B
1010
101010
1010
10
Elevation Elevation
Elevation
Chamfered Door Surround
BA
1200
1050
900
750 488 or 630
488 or 630
488 or 630
488 or 630
1350 488 or 630
Elevation
Note : Window Surrounds Available In 1,2,3,4 Light Surrounds
Plain Door Surround
Chamfered Window Surround Plain Window Surround
Available With Or Without Label Mould
Available With Or Without Label Mould
Door Opening To Suit Standard Metric & Imperial Frames
Available With Or Without Label Mould
Available With Or Without Label Mould
21 CHAMFERED KEYSTONE SURROUNDS
ABBEY ARTSTONE LIMITED - MDL/WD/04
BB
A A
B
AA
B
Kirkstall Door Surround
Kirkstall Window Surround
Rosedale Door Surround
Available With Or Without Lable Mould
Elevation
Note: Window Surrounds Available In 1,2,3,4 Light Surrounds
Elevation
Elevation
Rosedale Window Surround
488 or 630
488 or 630
488 or 630
488 or 630
488 or 630
1350
1200
1050
900
A
750
B
Elevation
Available With Or Without Lable Mould
Door Opening To Suit Metric & Imperial Frames
22BLOCK SURROUNDS
ABBEY ARTSTONE LIMITED - MDL/WD/03
140
215
25
B
BA
140
225150
B
BA
215
A A
1010
1010
Surrounds With Jamb BlocksPlain/Chamfered Door
With Jamb BlocksChamfered Surround
Elevation
Surrounds With Jamb Blocks
Note : Surrounds available to suit any size opening as required, Two light version shown
Plain/Chamfered Door
Available With OrWithout Label Mould
Jamb BlocksPlain Surround With
Elevation
Without Label MouldAvailable With Or
Without Label MouldAvailable With Or
Without Label MouldAvailable With Or
Also Available With Large Chamfer Or Moulded Jamb Block
Door Opening To Suit Standard Metric & Imperial Frames
23 CIRCULAR SURROUNDS
ABBEY ARTSTONE LIMITED - MDL/WC/01
AB
C
10
AB
C
D
10
E
AB
CD
E
215
B
140
160
272
6
100C 100
CW
140
900600
140
A
B
1
CW
2
100
25
D 100
25E
140C 140
CW
25
900600
25
A
B
3
CW
4
E 10 10
A 610
C
D
125
25
B 195
900
125
25
195
CW
5 6
CW
Elevation Section
SectionElevation
ElevationSection
Circular Window
Chamfered Circular Window
Keystone Circular Window
Available With Solid Infill Panel
Option
Available With Solid Infill Panel
Option
Available With Solid Infill Panel
Option
ABBEY ARTSTONE
ASHLAR & QUOINS
24ASHLAR & QUOINS
ABBEY ARTSTONE LIMITED
25 ASHLAR BLOCKS
ABBEY ARTSTONE LIMITED - MDL/AB/01
B
C
D
D
A
A
C
B
A
C
BD
D
B
A
C
A
CHB02R
A
B
C
D
04RCHB
05RCHB
06RCHB
05CHB
06CHB
215 215
215 215 215
20 20 20 20 20 20
290 290 290
100100100100100100
440 440 440 440
Chamfered Ashlar
Plain Ashlar
Rusticated Ashlar
Isometric
Section
Elevation
R = Reveal Blocks Chamfered3 Sides Only
Isometric
Elevation
Section 215
100
C
B
290
100
PAB01
440A
02
440
PAB
Full Blocks Half Blocks
Also Available 140mm On Bed
Isometric
Elevation
Section
IsometricElevation
Section
Rock Faced Ashlar
Half Blocks
100B 100
290215C
215215A
RAB04
RAB03
Full Blocks
290215C
440
100
440
100
A
B
RAB02
RAB01
Copings and pier caps are also available.We can also manufacture other surface finishes, subject to samples being produced.Rock faced quoins and blocks are designed to imitate a natural pitched face stone finish
A
A
A
100
219
440
PAB05
100
294
440
PAB07
125
215
440
PAB09
140
215.
440
PAB11
100
294
PAB08
C 290215 219
B
A
100
PAB
100
215
PAB03 04
100
06PAB
215.215
140
PAB12
125
10PAB
215 215 215 215 215
Also Available 140mm On Bed
RA04
85
215
290
RA
C 215 290 219
Full Blocks
B
A
85
440
01RA
85
440
85
440
02RA
05
215294 215. C 215
RA09
440
110
440
85
RA07
440
125
11RA
Half Blocks
B
A
85
215
RA03
215.294219 215
12RA
125
215
08RA
215
8585
215
06RA
110
215
10RA
Also Available 140mm On BedAlso Available 140mm On Bed
D 15 15 15 1515 15 D 15 15 15 1515 15
26QUOIN BLOCKS
ABBEY ARTSTONE LIMITED - MDL/QB/01
A
C
CD
25C
25
25
BB
D
A
C
B
DC
15
15
15
A25
C
B
D
A
C
A
02
440
100
290
215
C 100
D 215
A
B
328
215
01
A
Plain 90° Quoin Block
Chamfered 90° Quoin Block
Isometric
Isometric
Plan Section
Elevation
Elevation
Plan Section
PQB
440
100
215
03
215
215215D 290
CQB
03
440
240
100
353
240
100
B
A
C
440
240
100
CQB
01 02
CQB
Plan Section
Elevation
Isometric
Rusticated 90° Quoin Block
215215D 290
03
215
100
440
215
328
100
B
A
C
215
100
440
RQB
01 02
PQB PQB
RQB RQB
328
100
290
215
100
219
444
219
04PQB PQB
05
290
100
215
328
PQB
04
219
100
219
444
PQB
05
Reveal Blocks, Half Quoins And 135° Splayed Quoins Also Available
Reveal Blocks, Half Quoins And 135° Splayed Quoins Also Available
Reveal Blocks, Half Quoins And 135° Splayed Quoins Also Available
04
CQB
328
240
100
290
FQB FQB
Isometric
Elevation
Plan Section
C 100 100
215D 290
215B 215
215
04
A 215
05
Rock Faced Quoin Block Half Quoins
100
215
C
D
100100
215290
440A 328 440
215B 215215
FQB
01
FQB
0302
FQB
A
A
A
ABBEY ARTSTONE
PLINTH & STRING COURSE
27 PLINTH & STRING COURSE
ABBEY ARTSTONE LIMITED
28STANDARD STRING & PLINTH
ABBEY ARTSTONE LIMITED - MDL/S/01
BB
C
A
A
B
40D
40
C
B
A
A
D
Plain String Course
Isometric
Internal Return
Isometric
Isometric
Faced Ends For Returns
Isometric
Section
Plain Plinth Course
C 890 890
Section
215
140
PPB
F
E
990
890
990
890
B 140
A 140
PPB1 2
Isometric
Isometric
C 175
B
A
215
140
CPB1
100
140
140
CPB2
D 100 100
Internal Return
Section
PSC
65
890
100
C
Section
B
A
E
F
890890
PSCPSC
215
100
321
140
100
890
990
B
D
C
A
CSC1
140
100
90
150
With ThroatingsChamfered String Course
Isometric
Chamfered Plinth Course
Isometric
F
External Return
Plain
Plain
External Return
E
F
F
E
F
C C
Please Advise If RequiredFaced Ends For ReturnsPlease Advise If Required
CSC2
150
140
115
125
890
990
CSC3
125
140
115
100
890
990
*
* For Use WithRender
A=125For Use With Render
Option
29 STANDARD STRING COURSE
ABBEY ARTSTONE LIMITED - MDL/S/02
C
F
G
B
A
D
55 15
1555
30
D
B
C
A
EStandard String Course
Isometric
Isometric
Isometric
Isometric
Isometric
Isometric
150 125C 125
External ReturnSection
Internal Return
Plain
G
E
F
D
50 2525
202020
2020 20
100100 175
** For Use With Cill CL3* For Use With Cill CL2
Plain
External Return
A
B
100 100100
140140 215
SSC2
**1
SSC
*3
SSC
Moulded String Course
Internal Return990Section
21
90 90D
40E 40
140 140B
120C 250
100A 270
MSC MSC
890
990
890
990
990
E
30MOULDED PLINTH & STRING
ABBEY ARTSTONE LIMITED - MDL/S/03
B C CB
A A
0.02
9C
0.11
4
D
B
0.11
40.02
9
B
C
D
Section
Type .2.
F
E
990 990
890 890
Type .2.
Section
990
890
990F
E 890
External Return
Moulded String Course (Type .1. & .2.)
A
Section
Type .1.
Internal Return
D
Isometric
Isometric
140140A
5 6
C
B
D
A 140140
175
215
100
140
100 100
CPB CPB
890890E
F 990990
D
B
C
100100
140
100
215
175
Type .1.
Section
A
35
F
4CPB
3CPB
E
D 35
Isometric
Internal Return
Isometric
External Return
Moulded Plinth Course (Type .1. & .2.)
Plain
Isometric
With Throatings
F
Plain
Isometric
With Throatings
E
140140A
3 4
140
100
140
100
140
175
215
100
C
B
D
A
CSCCSC
890890E
990F 990
100
140
100
D
B
C
100
215
175
F
CSC5
CSC6
F
For Underbuild Plinth Course Units See MDL/S/01 &For Underbuild Plinth Blocks See Ashlar Walling She et MDL/AB/01
31 BULLNOSE STRING COURSE
ABBEY ARTSTONE LIMITED - MDL/S/04
115
65
147.5
100
65 50
125
R5.934
Bullnose String Course Type 2
Isometric
Isometric
Isometric
Plain
External Return
Bullnosed String Course Type 1
Internal Return
750
Section
750
750
600
Plan, Radius Sections
Isometric
Isometric
Isometric
Plain
Up To 1100
Internal Return
External Return
Section
Up To 1100
Up To 1100
*
*
Please State Handing Required* Special Angles And Radii Available To Order
*
*
Special Angles Available To OrderPlease State Handing Required*
ABBEY ARTSTONE
CORNICE, EAVES, DENTILS& CORBELS
32CORNICE, EAVES, DENTILS & CORBELS
ABBEY ARTSTONE LIMITED
33 MOULDED CORNICE
ABBEY ARTSTONE LIMITED - MDL/CN/02
600
140
7514
0
140
600
600
600
600
200
75
600
200
75
200
215
215
215
0.173
215
215
175
175
215
Section
15
51
38
26
45
Isometric
Plan View Right Hand Internal 90° Return*
Elevation
Moulded cornice
Section
Isometric
Plan View Right Hand External 90° Return*
Elevation
Plan View Left Hand Internal 90° Return *
Elevation
Moulded cornice
Elevation
Plan View Right Hand External 90° Return *
100 100
600
1000Max
6
19175 14
175
Special Angles Available If Required.*Please State Handing Required,
100
34DENTILS AND BAND
ABBEY ARTSTONE LIMITED - MDL/CD/02
AB
C
D
E
150100B
140C 140
300
1
A 300
2
Isometric
Side Elevation
Plan View
Front Elevation
Isometric
Plan View
Side Elevation Front Elevation
DB DB
Front Elevation
Plan View
Side Elevation
Isometric
A A
A
C
A
B
300
150
140
100
300
140
4DB3
DB
E 5050
D 210210
E
D
C
5050
210
140
210
140
B
A
6
150
300
5
300
100
DB DB
Plain Dentil Chamfered Dentil
Moulded Dentil
A B
C
A B
D
EC
Side Elevation
Plan View
A
Front Elevation
B
C
Band Block
Isometric A
A
C
B
Working Detail
Band Blocks
Moulded Corbel Stones
440
1BB BB
2
600
100 100
140 140
35 CORBEL
ABBEY ARTSTONE LIMITED - MDL/CD/01
A
C
A
C
B
D
B
D
A
C
B
D
E
EE
Side Elevation
Side Elevation
Corbel
Isometric
Plan View (Left Hand)
Corbel
Isometric
Plan View (Left Hand)
CBCB CB
100
*Please State Left Or Right Hand
CB12 Cut Out*
Front Elevation
CB10 & CB11 Solid
A
C
B
D
E
12*
440
328
215
10
528
11
440
328 328
100 100
215
100
215 215
100
100
CB7 & CB8 SolidCB9 Cut Out*
*Please State Left Or Right Hand
Front Elevation
B
A
D
C
E
CB
215
440
9*CB CB
100100
528
7
440
8
328
215
100
215
328
215
328
100
Side Elevation
Corbel
Isometric
Plan View (Left Hand)
A
3CB
558
215
328
100
100
*Please State Left Or Right Hand
Front Elevation
CB1,CB3 & CB5 SolidCB2,CB4 & CB6 Cut Out*
558558
2*1CB CB
328 328
140140
215100
100100
A
C
D
B
E
558
6*CB
558
4* 5CB
558
CB
290
328
215
100
215
328
215
100 100
290
328
100
A
A
ABBEY ARTSTONE
COPINGS
36COPINGS
ABBEY ARTSTONE LIMITED
37 STANDARD COPINGS
ABBEY ARTSTONE LIMITED - MDL/CP/01
B
B
CC
DD
B
C
D
Isometric
A
Section
Once Weathered Coping External Return
*
Isometric
*
A
Section
Once Weathered Coping Internal Return
Isometric
A
Once Weathered Coping
Section
38STANDARD COPINGS
ABBEY ARTSTONE LIMITED - MDL/CP/02
B
B
CC
DD
B
B
C
C
D
D
B
C
D
B
C
D
Isometric
A
Twice Weathered Coping Hipped End
Isometric
*
A
Elevation
Twice Weathered Coping Return
Twice Weathered Coping
Isometric
A
Section
Isometric
A
Section
*
Isometric
*
A
Section
Once Weathered Coping
Isometric
A
Please State Left Or Right Handed
Please State Left Or Right Handed
Once Weathered Coping
Section
Internal Return
External ReturnOnce Weathered Coping
Section
Please State Left Or Right Handed
39 MOULDED COPING
ABBEY ARTSTONE LIMITED - MDL/CP/03
B
C
B
C D
E
B
C
D
E
Moulded-Once Weathered (Type 1&2)
Moulded-Flat (Type 1&2)
Isometric
Isometric
Section (Type .1.)
Section (Type .1.)
Moulded-Twice Weathered (Type 1&2)
ASection (Type.1.)
A
A
Sizes to be specified by customer
Sizes to be specified by customer
Sizes to be specified by customer
40OTHER COPING DETAILS
ABBEY ARTSTONE LIMITED - MDL/CP/04
Or For Further Information Please Contact Our Sales OfficeFor Further Details See Our MDL/CP/01-04 & 06Units Available In All Coping ProfilesThe Above Typical Special Units We Are Able To Manu facture
Radius To Suit
External Vertical RadiusInternal Vertical Radius
Radius To Suit
Radius On Plan
Tee Unit
Ramp Down Unit
Radius To Suit
Angle To Suit
Ramp Up Unit
Angle To Suit
41 HALF ROUND COPINGS
ABBEY ARTSTONE LIMITED - MDL/CP/05
A
B
A
B
HRC2
Random Lengths
Section
75
Available In The Following Lengths
150100 125 175 200
A
in similar finishesQuoins and pier caps are also availablesubject to samples being produced
Rock faced copings are designed to imitatea natural pitched face stone finishWe can also manufacture other surface finishes,
600225 300
300
Hipped End
A Random Lengths
Isometric
Rock Faced Coping
600 Max
A
Isometric
600 Max
A
Isometric
Smooth Faced Copings
HRC1
225 112.5
150
187.5
225450
375
300
Isometric
A
600 Max
Hipped End
Internal Corner
A A
Section
ABBEY ARTSTONE
PIERS, CAPS & SPHERES
42PIERS CAPS AND SPHERES
ABBEY ARTSTONE LIMITED
43 PIER CAPS
ABBEY ARTSTONE LIMITED - MDL/PC/01
C
B
B B
DC
BB
C D
37.5
62
5.5
10
62
37.5
5.5
10
62
20
C
D
D
20
62
PlanPlan
Isometric
Sphere Base
Elevation
Isometric
Pier Cap
A
Elevation
Isometric
Moulded Cap
Isometric
Moulded Sphere Base
Elevation
To Order , Other Designs Can Be Manufactured . Please Contact Our Office For Further Details .
All Caps Available With Holes Cast Through To Alow Passage Of Cabling Or Pipework Rectangular And Circular Caps Available
Sphere Base
ØA
A
A A
Elevation
Type 1 Moulding
Type 2 MouldingType 2 Moulding
Type 1 Moulding
5757
44BALL FINIAL SETS
ABBEY ARTSTONE LIMITED - MDL/BF/01
B
C
D
BE
C
D
A
A
E
A
E
C
B
D
Ball Finials
Plan
Elevation
Type A
Plan
*Please Specify If OptionalBase Is Required SizesAre 450x450, 525x525 Or600x600mm
Elevation
Type B
E 102 102 102 102
350A 350
See BelowC
102E
*D 225
B 420
102
300
495
Of Sphere Required*Please Specify Size
B
Type
05
BF BF
06
607
225
C 470
*D225
300
595
607
A
B682
570 705 705
450375300
805
932
695 805
857682
BF
01
Type
A 04
BF
02
BF
03
BF
Finials Can Be Mixed AndUsed With All Base AndIntermediate Caps To Suit
375 450
102 102
990 990
1090 1090
857 932
BF
07
BF
08
Plan
Elevation
Type C
567
250
670
D
470
B
C 470
330250 330
667
705
567
670
667
705
BF
695
1110C 09
595A 595
Type BF BF
141312
695695 805
BFBF BF
467 467
200 200
E 102 102 102102 102 102
45 GATE PIERS
ABBEY ARTSTONE LIMITED - MDL/GP/01
440
590
A
240
480
125
150
705
990
150
990
830
705
545
C
D
BC
A
240 355CB
D
C
355
240 340
640
440
125125
Sml Pier
215/290
To Suit
Lrg Pier
Section B
10
Section D
10
B
C
A
D
300450
215/290
To Suit
10
10Chamfer50mm x 50mm
B
A
10
50mm x 50mmChamfer
10
10
Section C
C
Small Section
Section A
1010
C
10
Large Gate Pier Small Gate Pier
Large Section
Chamfered Gate Piers
POINTING : Joints Should Be Pointed Using Our Dry Mix. Or Use 1:1:6 Cement/Lime/Sand(Sand To B.S. 882 Grade F) Colour-Toned To Suit (White Cement May Be Necessary).BEDDING JOINTS : Use 1:1:6 Cement/Lime/Sand Mortar.
We Recommend That Gates Be Hung On Brackets Fixed To Adequate Steel Sections (Designed By Others).Experience Has Shown That Both Vertical And Torsional Deflections Can Be Generated From the Action of The Gates.It Is Essential, Therefore, That These Potential Movements Cannot Be Transmitted To The Pier Sections Or DamageMay Be Caused.A Suitable Clearance Between Bracket And Pier Shaft Must Be Allowed.
If The Gate Piers Are To Be Infilled With Concrete The Shaft Sections Should Be Lined With 25mm Polystyrene (OrSimilar) To Act As An Isolating Medium. No More Than Three Sections Should Be Concreted In One Lift. The ConcreteShould Only Be Hand Compacted. Subsequent Concrete Pours Should Only Take Place After The Concrete In TheProceeding Lift Has Reached Its Initial Set.Foundations To Be Designed By Others To Suit Site Conditions And Loadings.
990 705
46GATE PIERS
ABBEY ARTSTONE LIMITED - MDL/GP/02
A
890
990
D
830
CB
C
545 70
5
990
705
CA
CB
D 605
605
890
150
150
Section B
Section D 705990D
290
450
To Suit
Lrg Pier
A
B
C 215
300
To Suit
Sml Pier
50mm x 50mm
50mm x 50mm
Chamfer
B
Chamfer
D
A
C
Small Section
Section C
Section A
Rusticated Gate Piers
Small Gate Pier
Large Section
Large Gate Pier
215
For PiercapsSee MDL/PC/01,02
For FinialsSee MDL/BF/01
POINTING : Joints Should Be Pointed Using Our Dry Mix. Or Use 1:1:6 Cement/Lime/Sand(Sand To B.S. 882 Grade F) Colour-Toned To Suit (White Cement May Be Necessary).BEDDING JOINTS : Use 1:1:6 Cement/Lime/Sand Mortar.
We Recommend That Gates Be Hung On Brackets Fixed T o Adequate Steel Sections (Designed By Others).Experience Has Shown That Both Vertical And Torsional Deflections Can Be Generated From the Action of The Gates.It Is Essential, Therefore, That These Potential Mo vements Cannot Be Transmitted To The Pier Sections Or DamageMay Be Caused.A Suitable Clearance Between Bracket And Pier Shaft Must Be Allowed.
If The Gate Piers Are To Be Infilled With Concrete The Shaft Sections Should Be Lined With 25mm Polystyrene (OrSimilar) To Act As An Isolating Medium. No More Than Three Sections Should Be Concreted In One Lift. The ConcreteShould Only Be Hand Compacted. Subsequent Concrete Pours Should Only Take Place After The Concrete In TheProceeding Lift Has Reached Its Initial Set.foundations To Be Designed By Others To Suit Site Conditions And Loadings.
ABBEY ARTSTONE
GABLE VENTS, NAMESTONES& CHIMNEY CAPS
47 GABLE VENTS, NAMESTONES & CHIMNEY CAPS
ABBEY ARTSTONE LIMITED
48GABLE VENTS
ABBEY ARTSTONE LIMITED - MDL/GV/01
B
A
EF
ED
C
D
Indented Faces Can Be Recessed Plain Or Punched / Textured Face, Faces Can Also Be Carved With Letter ing If Required
Gable Vent
BB
ELEVATION
CHAMFERED
25x25mm CHAMFER * ELEVATION
B
ELEVATION
DIAMOND
CIRCULAR
Feature Blocks
A
SQUARE
ISOMETRIC ELEVATION
SECTION
C
A
*= 125mm Bed
FB1 FB2
A
150
150
A
B
C 100
215
215
100
FB5FB4FB3
600
600
440290
440290
100100 100
1GV
328
590
100
300
40
145
SECTION
A
B
C
F
E
D
32GV
215 450
GV
365
100 140
900
50
185
40
600
10050
49 SIMPLE NAMESTONES
ABBEY ARTSTONE LIMITED - MDL/NB/01
A
B
A
A
B
20
B
A
B
CC
CC
19 96
C 25
B
A
01
D
NCS
25
290
100
02NCS
100
215
100A
B
D
290
100
600
215
440
02NS
01NS
Section
Section
Chamfered Date Stones
Plain Date/Name Stones
6050
B 290
D
C
440
100
7
A 100
8
Section
9
600
100
100
NSCNSCNSC
2400mm Max
Chamfered Name Stone
Section
Plain Name Stone
440
100
2400mm Max
87
D
A
B 290
100
NS NS9
100
600
NS
600440D
All lettering is hand carved, style to your requirements.Lettering can be plain or picked out in colour to suit.Logo's can also be incorporated subject to carving
limitations.
D
D
D
In One Piece
In One Piece
50SPECIAL NAMESTONES
ABBEY ARTSTONE LIMITED - MDL/NB/02
B
560
560
A A
B
C
D
6284
6284
C
950
800
Section
ElevationElevation
Section
B
A
100 100 100
NS NS
440
4
600
5NS
900
6
D 20 20 20
A
C
B
440 600
NSC4
NSC5
900
6NSC
100 100 100
100 100 100
Plan
Plan
R475
1996
Section A-A
Section B-B
All Lettering Is Hand Carved, Style To Your RequirementsLettering Can Be Plain Or Picked Out In Colour To Suit.Logo's Can Also Be Incorporated Subject To Carving Limitations
A-A
B-B
20121996HouseAbbey
Chamfered Date/NameStone Plain Date/NameStone
Circular Featured Date/NameStone Square Featured Date/NameStone
1996HouseAbbey
51 CABLE COPING AND CAPS
ABBEY ARTSTONE LIMITED - MDL/CU/01
D
C
10
BA
A B
E
DC
A
B
D
E
G
F
C
A 50
Isometric
600D
B 100
425C
Elevation
Double Chimney Cap
Cast In Two
Plan
Isometric
D CC2
600C
E 70
C 75
Square Aperture Holes Also AvailablePlease State Size Of Hole Required
Section
Single Chimney Cap
= Lengths Cut To Suit On Site*
Isometric
*600
100B
A 50
CC1S
26E
D 75
Chimney Copings
= Lengths Cut To Suit On Site
Isometric
*Section
150B
102A
CCP1
F 130
110G
900 *
Chimney Copings
C 40
D 75
98B
102A
MCP1
Square Aperture Holes Also AvailablePlease State Size Of Hole Required
ABBEY ARTSTONEWorth Valley Works, Pitt Street, Keighley, West Yorkshire, BD21 4PF
Semi Dry | Wet Cast | Glass Reinforced Concrete | Glass Reinforced Plastic
Company Registration Number : 7529533
Tel. 01535 610964 Fax. 01535 690989 Email. [email protected]