Date post: | 15-Apr-2017 |
Category: |
Documents |
Upload: | peter-gilder |
View: | 66 times |
Download: | 4 times |
MAKING IT POSSIBLE
For more than 25 years, Bourgault Tillage Tools have been at the forefront of innovation and technical development in the tillage and seeding tools industry. This was borne out of their own farming and hands-on field experience and the realisation that leadership was sorely lacking in the research and development of tillage and seeding tools.
Speed-Loc ///12 years ago, Martin Lishman Ltd introduced the Bourgault Tillage Tools Speed-Loc system to UK farmers. Now standard fit on all major UK manufactured cultivators, Speed-Loc can be retrofitted to almost any tined cultivator on the market.
TM
Speed-Loc ///
• Fast & easy point changing - a few minutes rather than hours saves time and money
• Upper stop keeps points at the same depth - critical for uniform crop emergence
• Spring-loaded pin prevents loss of points - backed by a 100% guarantee
• Durable and long-lasting - heat treated casting and stainless steel components
• Fits most types and shapes of tine - from standard to heavy duty applications
Once the tine is fitted with a Speed-Loc Adapter, the whole range of Bourgault Tillage Tools is available for use
The Benefits of the Speed-Loc Adapter
A few hits and the point is locked on.
Speed-Release Tool depresses the locking pin and the point is easily
removed by striking the top.
Upper stop ensures points run at consistent depth.
Urethane spring applies pressure to the locking pin and seats against the tine.
Special side-locking nuts should always be used to prevent vibration loosening the adapter on the tine.
Heat treated stainless steel locking pin provides a secure locking mechanism that will not rust or corrode.
Bolts seat closely in the casting to avoid twisting on the tine.
6 7
Speed-Loc ///Speed-Loc Adapters Examples of tines retrofitted by users
200-QCA-5010
Suits the widest range of tines, including Simba Great Plains.
2¼” (57mm) bolt-hole spacing, 50° angle. Requires 7/16” or 1/2” o/s head plough bolts c/w side- lock nuts.
200-QCA-4710
Grooved rear side suits Kongskilde as well as conventional tines.
1¾” (44mm) bolt-hole spacing, 47° angle. Requires 7/16” or 1/2” o/s head plough bolts c/w side-lock nuts.
200-QCA-5030
Fits Horsch FG/FX Terrano & Vaderstad Top Down tines.
57mm bolt-hole spacing, 50° angle. Requires M12 10.9 plough bolts c/w stover nuts.
200-QCA-5020
Slotted hole suits a wide range of non-standard tines.
63-80mm bolt-hole spacing, 50o angle. Requires M12 10.9 plough bolts c/w stover nuts.
200-QCA-4700
Flat-backed. Fits Knight.
1¾” (44mm) bolt spacing, 47° angle. Requires 1/2” hex head bolts c/w side-loc nuts.
410-QCA-5020
Fits Lemken.
45mm bolt spacing, 50° angle. Requires M12 10.9 plough bolts c/w stover nuts.
410-QCA-5050
Fits Kverneland CLD Grubber.
45mm bolt spacing, 50° angle. Requires M12 10.9 plough bolts c/w stover nuts.
Will the Speed-Loc adapter fit my tine?For more information on the Speed-Loc adpator, please contact us on 01371 830358 or at [email protected]
Horsch CO and Sprinter Conversion
When fitted with the tine adapter, the side-bolting CO and spriner classic tine can be converted to accept a Speed-Loc adapter (200-QCA-5010), sweep and drilling system.
Horsch Terrano Tine
Both the FG and FX versions of the Terrano tine are retro-fitted with the specially designed 200-QCA-5030 Speed-Loc adapter and, typically, 12” (30.5cm) sweeps (200-PWV- 1208).
Opico HE-VA
The Master-Tiller, Triple-Tiller and Combi-Lift models from the Opico HE-VA range have been fitted with the 200-QCA-5010 Speed-Loc Adapter. Primary cultivation points such as the 200-PWV-0528 have then been used.
Vaderstad Top Down
Uses the same specially designed Speed-Loc adapter (200-QCA-5030) as the Horsch Terrano tine. Typically fitted with 9” (23cm) sweeps (200- PWV-0908). The Vaderstad Cultus tine accepts the 200-QCA-4710 Speed-Loc adapter.
8 9
Sweep Points ///Quick Change
Quick Change Sweep Points ///
• Versatile system - from minimum cultivation to full tillage across the machine width
• Manufactured from high Boron steel - heat treated for longer life
• Parallel wing design - maintains original width throughout its wear life
• Superior crown design - keeps the tip sharp for good penetration as the sweep wears
• Narrow stem - causes less soil disturbance and leaves a smoother field finish
• Huge range to fit the Speed-Loc system - from standard to heavy duty applications
Benefits of Sweeps from Bourgault Tillage Tools
Bourgault Tillage Tools have a reputation for quality and durability. All points are even wearing and long lasting.
Every one is checked during manufacture for accuracy in shape and fit to the Speed-Loc Adapter.
The Narrow Stem design means the sweeps disturb less soil, which ensures good soil moisture retention and leaves a smoother field finish.
The ends of the wings are cut parallel to each other which ensures that the sweep maintains its width as it wears and provides maximum value.
The sweeps are manufactured from high Boron steel, heat treated for longer life.
The crown of the sweep is designed so that the tip stays sharp as it wears, which is important for good penetration in tough conditions.
Most sweeps are available in 6mm thickness or the better value and more durable 8mm thick versions - better suited to the UK’s abrasive and stony conditions.
12 13
Quick Change Sweep Points ///Sweep PointsThere are over 50 Speed-Loc Points to choose from: 6mm or 8mm, standard or heavy duty and seed-bed preparation or primary cultivation tools. After 12 years use in the UK a pattern of types to suit different machines in our range of soils has emerged and are usually available from stock. The most commonly used points are 8mm thick from standard duty (200 series) range. Some popular examples are shown below.
3” (7.6cm)
200-SPN-0308
Used on Claydon, Knight and others.
51⁄2” (14cm)
200-PWV-0508
Used on Knight, Claydon, Horsch and
others.
7” (18cm)
200-PWV-0708
Used on Knight, Claydon and others.
9” (23cm)
200-PWV-0908
Used on Simba Great Plains, Knight, Bristow and others.
12” (30.5cm)
200-PWV-1208
Used on Horsch, Sumo (modified by Sumo) and others.
Heavy Duty Points (410 series)
12” (30.5cm) 410-PWV-1208Used on heavy duty machines such as Kverneland CLD and Pottinger Synkro.
Other heavy duty sweeps available but rarely used. Please enquire.
Other sizes available: 4” (10cm), 10” (25.4cm), 11” (28cm), 13” (33cm), 14” (35.5cm), 16” (42cm) and 18” (46cm).
Usage examples are not comprehensive and some machines use different sizes according to the conditions. For more information about converting your machine, please contact us on 01371 830358 or at [email protected]
Primary Cultivation ToolsThe range includes spikes and points with hardened and extended-wear pads to improve penetration in tough soil conditions. The wear pads, with a hardness of 52-56 HRC, increase life expectancy and give longer wear times. For deeper working, extended heavy-duty wear pads protect the pin in the Speed-Loc adapter.
SpikesIdeal for primary cultivation in very dry and hard conditions. Two versions are available:
Both are 2¼” (57mm) wide, 5⁄8” (15mm) thick and 6” (15cm) long. Use the 0215, with the extended heavy-duty wear pad, when working at greater depths.
200-SPK-0200 200-SPK-0215
Extended Wear PointsIn addition to a hardened wear pad, the point on these sweeps runs 1⁄2” (12mm) lower than the standard sweeps. This increased pitch improves penetration in hard or compacted ground.
With 4” (10cm) wings (6mm thick on the 0405, 8mm thick on the 0428) and 2¼” (57mm) wear pad. Use the 0428, with the extended heavy-duty wear pad, when working at greater depths.
5½” (14cm) or 9” (23cm) wings, 8mm thick, with extended heavy-duty wear pad for working at greater depths.
200-PWV-0428 200-PWV-0405
200-PWV-0528 200-PWV-0928
14 15
Drilling System ///Quick Change
Quick Change Drilling System ///
• Versatile system - six different inter-changeable seed boots to choose from
• Designed for ease of use - seed boots are easily changed by removing one bolt
• Utilizes the Speed-Loc adapter to fit the seeding opener
• The system can be adapted to suit all UK drilling conditions
• The system is perfect for allowing a range of uses with the same drill
• Can be retrofitted to many drill types
Benefits of the Quick Change Drilling System
Quick Change Seed Boot Assembly
Typical Quick Change Combinations
Seed Boot Holder
Single bolt to change seed boot
Seed Boot (splitter)
Speed-Loc Adapter
Seeding Opener (Sweep)
Drilling Cereals
Splitter seed boot splits seed into two even rows that can merge in the centre to give an overall 7” (18cm) band.
Used with sweeps of 5½” (14cm) upwards.
Drilling Cereals
Spreader seed boot spreads seed evenly in a band 4-6” (10-15cm) wide, depending on sweep used.
Used with sweeps of 4” (10cm) upwards.
Drilling Rape
Short, straight seed boot spreads seed c.2½” (63mm).
Works well with spoons, spikes or any size of sweep.
Drilling Beans
Bean seed boot places the seed in a very narrow band, at a depth which depends on the opener used.
Normally used with a knife opener.
18 19
Quick Change Drilling System ///Quick Change Seed Boot AssemblyThe quick change drilling system is comprised of four separate components: Seeding Opener, Speed-Loc adapter, Seed Boot Holder and Seed Boot. Choosing the right combination of components is determined by the crop being drilled, and is key to achieving the best results when drilling. The choices available in the Bourgault Tillage Tools range mean that you can always choose the right tool for the job, rather than having to compromise.
Adapter Holder Seed Boot
There are additional seed boot holders and seed boots available, but rarely used in UK conditions - the complete range, including accessories such as seed hose bushings to fit the seed boot holders, are part of the full range at BROCK PARTS. Some accessories are listed on page 27.
200-QCA-4700
Flat-backed47° 1¾” (44mm)
bolt spacing.
200-QCA-4710
Curved back 47° 1¾” (44mm)
bolt spacing.
200-QCA-5010
Curved back 50° 2¼” (57mm)
bolt spacing.
200-QCA-5020
Curved back 50° 63-80mm bolt
spacing.
200-QCA-5030
Curved back 50° 57mm bolt-
hole spacing.
300-HLD-4700
Flat mounting,1¾” (44mm) bolt spacing.
300-HLD-4710
Curved mounting,1¾” (44mm) bolt spacing.
300-HLD-5010
Curved mounting,2¼” (57mm) bolt spacing. When used with the 200-QCA- 5020 Speed-Loc adapter may require an adapter wedge to ensure a good fit (see p.22).
300-ATM-1000
Spreader
Seed evenly spread in a 4-6” (10- 15cm) band.
300-ATM-1010
Splitter
Seed splits into two even rows that can merge in the centre to give an overall 7” (18cm) band.
300-ATM-1020
Straight
Spreads seed c.2 ½” (63mm).
300-ATM-1036
Knife
Places seed in a narrow band. Modified for larger bean varieties such as Wizard.
Seeding Openers
SweepsA sweep is the most frequent seeding opener used on tine drills. The sweep can match the seed boot used: the spreader seed boot is best used with the 4” (10cm) sweep (200-PWV-0400) or 5½” (14cm) sweep (200-PWV-0508); the splitter seed boot would be used with the 200-PWV-0508 or the 7” (18cm) sweep (200-PWV-0708). If a greater width of disturbance is needed while drilling, a wider sweep can be used.
SpoonsSpoons are very easy-pulling openers giving moderately low soil disturbance if working speed is kept around 7.5 km/h. When used with the straight seed boot, the 2¼” (57mm) spoon (200-SPN-0208) will provide a 2” seed spread and the 3” (76mm) spoon (300-SPN-0308) will give a 3” spread.
SpikesSpikes may be used as a seeding opener, but only to give extra penetration. They will create more disturbance than spoons.
KnivesSeeding with knives is commonly associated with drilling beans, though there are many options possible for creating narrow seed channels. The 200-KNF-0810 (pictured left) is a 3⁄4” (19mm) wide knife which is designed to work ahead of the bean seed boot and create very little disturbance. It has a chrome tip which provides reasonably long wear in non-abrasive conditions. Also available with a carbide tip (200-KNF-0811 - see below).
Carbide KnivesThere are many options for knives fitted with carbide tiles. Not only do they provide extra wear in abrasive soils, they also have a steeper angle of entry into the soil which means they will not lift and pull rocks and stumps to the surface. The 200-KNF-0811 has a 1” carbide tile for shallow drilling, the 200-KNF-0813 (pictured left) has a 3” long carbide zone for extra wear when drilling deeper.
20 21
300-ATM-1035
Knife
Places seed in a very narrow band.
Opener System ///Versatile
The Versatile Opener System (VOS) allows you to build the opener that fits your needs by choosing your tip and holder. Used for Direct Drilling, minimum tillage applications and ensures minimal soil disruption.
Versatile Opener System ///
24 25
3 1/2” (88mm) paired row double shoot tip with 3/4” horizontal and no vertical separation of seed/fertiliser Carbide on the nose and the cutting edges of the wings for abrasive conditions.
610-TIP-3500
The Paired Row design allows seed to be delivered in two distinct rows measuring 3” centre to centre while fertiliser is placed in the centre. Carbide placement provides sharp cutting edges for excellent penetration and the Paired Row tip achieves excellent seedbed results. Available with Horizontal seed/fertiliser separation (610-TIP-3500) and Horizontal/Vertical seed/fertiliser separation (610-TIP-4081).
The Benefits of the VOS Single Shoot Tip Options Paired Row Tip Options
Single Shoot
610-TIP-0802
Paired RowThe Versatile Opener System (VOS) enables you build the opener that fits your needs. The system consists of 2 parts, the holder and the tip. Different seed and fertiliser placements can be achieved by choosing between single shoot and Horizontal and Vertical Paired Row tips.
Tailored for you: Build the opener that fits the needs of your system and places the seed and fertiliser in the optimum position.
Disturbance: Developed for the North American market by the market leaders, these openers have specific working angles resulting in low disturbance and maximum moisture retention.
Carbide Placement: Years of research and development have resulted in a unique knowledge of tungsten carbide adhesion and placement brought together in the VOS tips guaranteeing high wear rates and consistent application.
Versatility: With various options of holders and compatible opener tips available the VOS continues the Bourgault benefits of versatility and reduced downtime.
Seed is delivered in a single row measuring 3/4” wide. (610-TIP-0802). Carbide placement provides sharp cutting edges for excellent penetration and the Paired Row tip achieves excellent seedbed results. Twin in line outlets allow simultaneous seed and fertiliser placement if required.
3/4” (19mm) long-wearing single shoot tip with long carbide on the nose for highly abrasive conditions.
VOS HoldersDrill specific holders with pre-set mounting angles for optimum performance. Available in stock to fit the Horsch Classic shank 84 degree tine.
For more information and further options on the Versatile Opener System, please call us on 01371 830358 or email [email protected]
610-TIP-4081 4” (100mm) paired row tip with 3/4” horizontal and 3/4” vertcal seed/fertiliser separation. Carbide on the nose, cutting edges of the wings and carbide inserts on the rear of the wing to seal the fertliser trench.
The Importance of the Adapter Nuts and BoltsThe Speed-Loc adapter will not be effective for long if it is not secured to the tine properly. Each adapter has a designated bolt type and size: Imperial (1⁄2” or 7/16” over-size head ), Metric (M12 10.9), Plough or Hexagon (as detailed on Page 8). The casting of the adapter is designed to accept the head and thickness of the designated bolt and it is essential that the correct one is used. Similarly, a corresponding Imperial (1⁄2” or 7/16” Grade 8 side-locking) or Metric (M12 stover locking) nut must be used to ensure a secure fit to the tine that will not be loosened by vibration.
The Ideal AngleFor best results and longest wear times Bourgault sweep points should be fitted so the angle of entry into the soil is between 2° and 5° from the horizontal. Speed-Loc Adapters ensure this on most machines, but some may also need one of the angled wedges shown below.
To check the angle, fit one or two tines with an adapter and sweep, stand the machine on level concrete and measure the height between the back tip of the sweep and the ground.
Sweep width Pitch height range
5.5” / 14cm 4 - 10mm
7”/18cm 5 - 13mm
9”/23cm 6 - 17mm
10”/25.4cm 7 - 18mm
11”/28cm 8 - 20mm
12”/30.5cm 8.5 - 22mm
13”/33cm 9 - 24mm
14”/35.5cm 10 - 26mm
16”/42cm 12 - 30mm
18”/46cm 13 - 33mm
The urethane tine wedges alter the pitch of the point on the Speed-Loc Adapter. The ideal angle for longest wear time of the point is between 2-5° from the horizontal.
Ideal range of sweep pitch heights
Decreasing Pitch Increasing Pitch
If the pitch height is outside the ideal range, a urethane plastic wedge is used to change the distance by the amount shown.
2o = 5mm
5o = 11.5mm
7o = 16mm
10o = 22mm
Range of angled tine wedges(see part numbers on next page)
26
Accessories ///
Angled Tine Wedges
2o = 5mm (200-WDG-0206)
5o = 11.5mm (200-WDG-0506)
7o = 16mm (200-WDG-0700)
10o = 22mm (200-WDG-1006)
Used to obtain proper sweep pitch on the tines.
Sub-plate (200-QAS-4711)
May be required when fitting the 200-QCA-4710 adapter to the Kongskilde VFM tine.
Speed-Release Tool (200-REL-1010)
Used to remove sweep points and drilling openers from Speed-Loc adapters.Drivers
Used to install drilling openers such as knives (400-DRV-1010)
Used to install sweep points and spoons (400-DRV-1000)
Helps keep tips sharp.Other types are available, see website for more details.
200-SLC-1001
Replacement bushing
(supplied with dust seal)
200-SLC-1010
Replacement dust seal
200-SLC-1020
Replacement locking pin
200-SLC-1030
Replacement spring ball for 200-QCA-4700
adapter
200-SLC-1035
Replacement spring ball for
200-QCA-4710 & 200-QCA-5010
adapters
200-SLC-1037
Replacement spring ball for
200-QCA-5020 & 400-QCA-5050
200-SLC-1038
Replacement spring ball for 200-QCA-5020
adapter for special applications
200-SLC-1039
Replacement spring ball for 200-QCA-5030
adapters
Speed-Loc Replacement Parts
Quick Change Drilling Accessories
Securing Nut & BoltSecures the quick-change seed boots into the seed boot holder.
300-BNC-4414
Drill Hose BushingsAdapts drill air hoses to
fit the top of the seed boot holder.
300-BSH-1200Adapts from a 28mm to a 31mm O.D. air hose
300-BSH-1205Accepts a 28mm O.D.
air hose
27
Speed-Loc Accessories
Further Notes ///
Bourgault Tillage and Drilling Tools are designed and manufactured in Canada by F.P. Bourgault Tillage Tools Ltd (BTT). © All designs are copyright F.P. Bourgault Tillage Tools Ltd who reserve the right to alter product specifications at any time without notice. ®The symbol and BTT are Registered Trade Marks of F.P. Bourgault Tillage Tools Ltd. Speed-Loc is a Trade Mark of F.P. Bourgault Tillage Tools Ltd.
Bourgault Tillage and Drilling Tools are imported and distributed exclusively in the UK and the Republic of Ireland by Martin Lishman Ltd. No guarantee of performance or results is implied by the representation of Bourgault Tillage Tools alongside the products of other manufacturers.
All business is subject to our terms and conditions. A full copy can be supplied on request.
© Martin Lishman Ltd March 2016.
Which speed-Loc adapter fits your machine?
On the right is a guide to the Speed-Loc Adapters that fit European cultivators and drills. The list is not comprehensive and may change with different models in a manufacturer’s range. If you do not see your machine listed, measure the centre to centre bolt hole distance on the tine and check against the specifications of the models shown on page 8. It is important that the angle of the point is correct when fitted on the adapter. See page 26 for more details about this.
Manufacturer/Type
Bristow
Claydon V Drill SR Drill Hybrid Drill
Cousins
Farm Force (Vaderstad Leg)
Glencoe
Horsch FG/CO FG/FX Terrano
International Chisel Plough
Knight/Raven
Knoche
Kockerling
Kongskilde
Adapter
200-QCA-5010
200-QCA-4700/5010200-QCA-4710/5010200-QCA-4710
200-QCA-5010
200-QCA-4710+100-WDG-0700*
200-QCA-4710
200-QCA-5010200-QCA-5030
200-QCA-5010
200-QCA-4700
200-QCA-5010
200-QCA-5020+200-WDG-0206*
200-QCA-4710+200-QAS-471†
Manufacturer/Type
Kverneland Combi-cult CLD-Grubber
Lemken Terradisc
Micheal Moore Double Press
Opico
Pottinger Synkro
Quivogne Jupiter
Rabe Firebird Profibird
SMS
Simba Great Plains
Vaderstad Cultus Top Down
Vogel & Noot/Rau Polymag
Wilrich
Adapter
200-QCA-4710410-QCA-5050
410-OCA-5020
200-QCA-4700
200-QCA-5010
200-QCA-5050
200-OCA-4710
200-QCA-5020200-QCA-4710
200-QCA-5020+200-WDG-0506*
200-QCA-5010
200-QCA-4710200-QCA-5030
200-QCA-5020
200-QCA-5710
North American machines are listed in the Bourgault Tillage Tools catalogue or online at www.tillagetools.com.
*Urethane wedge to ensure correct angle when a point is fitted to the adapter †Metal sub-plate to conform to tine profile
Your Bourgault Tillage Tools stocking specialist:
Tel: 01371 830358E-mail: [email protected]
Sole importer of Bourgault Tillage Tools:
www.martinlishman.com