BSR 2014.xlsx

For

Urgent Special Repairs, Renovations, Additions and Improvements, Minor Works and Maintenance to

Government Buildings- 2014

Department of Buildings

Chief Engineer Estimates, Estimate Division, Dept. of Buildings,

Building Schedule of Rates

B.S.R-2014

" Sethsiripaya", Battaramulla.

B.S.R-2014

BSR 2014- Department of Buildings

S07-2

CONTENTS

* GENERAL NOTES

* PRICING PREAMBLE

* PRELIMINARIES

A DEMOLISHER

B EXCAVATOR

C CONCRETER

D BRICK LAYER

E MASON

F PAVIOR

G ROOFER

H CARPENTER & JOINER

J IRON MONGER

K BRASS FOUNDER

L PLASTERER

M TINKER

N GLAZER

P PAINTER & DECORATOR

Q PLUMBER

R DRAIN LAYER

S MISCELLANEOUS

T ELECTRICAL INSTALLATION

U ALUMINIUM FABRICATOR

* FIGURES


S07-2

* INDEX


S07-2

PAGE

S07-03

S07-06

S07-23

S07-25

S07-28

S07-30

S07-33

S07-35

S07-36

S07-41

S07-45

S07-53

S07-59

S07-62

S07-64

S07-66

S07-67

S07-72

S07-98

S07-102

S07-106

S07-113

S07-156


S07-2

S07-194


Esti Rana / BSR 2014 S07 - 3

GENERAL NOTES

1.0 Timber :

(Group-1): Door, Window and Fanlight Frames

Category A Satin Palu Milla Ketakala Halmilla Mee Hulanhik Wewarana

Kohomba

Category B Grandis

(Group-2): Door , Window and Fanlight Sashes , Cupboards,

Counters and ShelvingCategory A Satin Tulan Halmilla Mahogany

Kohomba Wewarana Hulanhik Sooriya mara

Category B Ginisapu

(Group-3): Roof Framework

Category A Madan Milla Palu Wewarana

Mee Valdel. Micro Kolon

Category B Domba Grandis

(Group-4): Ceiling Framework and Partitions

Category A Satin Palu Milla Ketakala Halmilla Mee Hulanhik Wewarana

Kohomba Etathimbiri

Category B Domba Grandis

(Group-5): Valance Board and Valley Boarding

Category A Kolon Tulang Val Del Kohomba

Mahogany Satin Hulanhik Wewarana

Category B Ginisapu

(Group-6): Beadings :

Alstonia Mahogany Lunumidella

(Group-7): Special Timber

Category A Teak Category B

Unless otherwise specified in the respective Trades / Sections , the timber for all trades shall be as specified in Carpentry and Joinery.

All timbers under exceptional Circumstances, any equivalent timber to the given Species may be used with the approval of the Engineer.



2.0 Trade Names ;

3.0 Method of Measurement

4.0 Measurements :

5.0 Materials at site (Prime Cost of materials)

6.0 Mark-Up:

7.0 Machinery Usage in Basic Rate

8.0 Hiring of plant and equipment (Other than specified)

Where trade names , brands and / or catalogue numbers are referred to sole preference to any material or equipment is not intended . Any other material or equipment may be used, provided that the characteristics of type, quality, appearance, finish, method of construction and / or performance is not less than specified and provided also that approval is first obtained.

This Bill of Quantities has been prepared generally in accordance with the principles of "Standed Method of Measurement of Building Works(First Revision) , Sri Lanka 573:1999"

Bidders are to note that the measurements are taken absolutely nett, unless otherwise stated and they must , therefore, allow in their prices for all straight cutting and waste, laps, etc. throughout even though not specifically mentioned.

Material rates shall cover all the expenses of Contractor such as Loading, Delivery to site , Unloading, storing and protecting etc.

Combining the factors for overheads and the profits factors 28.8% is obtained from the basic rate as the Overhead and Profit factor, which is also called the " Mark-Up" on the Basic Rate. i.e. the Basic Rate is multiplied by the factor 1.288 to obtain the working rate or the BSR rate.

This basic rate analysis does not include for the use of heavy plant and equipment. This analysis provide for a labour intensive method of work with a minimal use of machinery. The machinery allowed in this analysis is the concrete mixture, the vibrator and a hoist in the case of a multi-storied building for the lift of materials to the various floors.

In case of hiring plant and equipment (Other than specified) in hourly basis. Plant shall be in good working condition and include for the cost of fuel, Lubricants, Transport to and from the site, wages and allowances of the operator, and any other expenses and charges etc.



9.0 Allowances for lifting work

The rates refer to works on the ground floor items in the BSR (other than specified),

Allowances to be made in the rates for lifting respect of work on upper floors.

(a). Ground and 3 upper floors

Serial No. Item

1 Concrete (cube) 3 5

2 9" Brickwork (sqr) 5 7

3 9" Brickwork (cube) 5 7

4 4 1/2" Brickwork (sqr) 5 7

5 Steel reinforcement (cwt) 2.5 5

6 Plastering (sqr) 5 10

7 Floor Tiling (sqr) 2 4

8 Wall Tilling (sqr) 2 4

9 Roof Calicut tile (sqr) 3 6

10 Roof asbestos (sqr) 3 5

11 Ceiling work (sqr) 3 5

12 Painting (sqr) 3 6

(b).Fourth floor and above

B.S.R is limited to work on the ground and 3 upper floors only. In cases, where the rates are not specified beyond ground floor, upto 3rd floor level the percentages indicated in table below should be added to the ground floor rates of relevant trades in the BSR, to obtain the rates applicable to the 1st, 2nd and 3rd floors respectively & in which. Additions beyond the ground floor rates cover the extra costs incurred for raising scaffoldings and involvement of labour for Lifting goods and etc. (Acceptable floor to floor height may be around 12 feet)

Ground to 1st floor %

Ground to 2nd floor %

In case of a building, having more than four floors , It will necessary to be raise a separate scaffolding system in an effective manner, to carryout the exterior works of the building.



TulangValdel.

Tulang

Etathimbiri

TulangValdel.

Sooriya mara

Jak

Unless otherwise specified in the respective Trades / Sections , the timber for all trades shall be as specified in

All timbers under exceptional Circumstances, any equivalent timber to the given Species may be used with the



Where trade names , brands and / or catalogue numbers are referred to sole preference to any material or equipment is not intended . Any other material or equipment may be used, provided that the characteristics of type, quality, appearance, finish, method of construction and / or performance is not less than specified and

This Bill of Quantities has been prepared generally in accordance with the principles of "Standed Method of

Bidders are to note that the measurements are taken absolutely nett, unless otherwise stated and they must , therefore, allow in their prices for all straight cutting and waste, laps, etc. throughout even though not specifically

Material rates shall cover all the expenses of Contractor such as Loading, Delivery to site , Unloading, storing

is obtained from the basic rate as the " on the Basic Rate. i.e. the Basic Rate is multiplied

This basic rate analysis does not include for the use of heavy plant and equipment. This analysis provide for a labour intensive method of work with a minimal use of machinery. The machinery allowed in this analysis is the concrete mixture, the vibrator and a hoist in the case of a multi-storied building for the lift of materials to the

in hourly basis. Plant shall be in good working condition and include for the cost of fuel, Lubricants, Transport to and from the site, wages and allowances of the



The rates refer to works on the ground floor items in the BSR (other than specified),

Allowances to be made in the rates for lifting respect of work on upper floors.

7910104.515669779

B.S.R is limited to work on the ground and 3 upper floors only. In cases, where the rates are not percentages indicated in table below should

, to obtain the rates applicable to the 1st, 2nd and 3rd floors respectively & in which. Additions beyond the ground floor rates cover the extra costs incurred for raising scaffoldings and involvement of labour for Lifting goods and etc.

Ground to 3rd floor %

In case of a building, having more than four floors , It will necessary to be raise a separate scaffolding



1. GENERAL

a.

b.

c.

.





e.

2. EXCAVATION AND EARTHWORK

a.

b.

c.

d.

e.

f.





f.

g.

3. CONCRETE WORK

Rates for concrete work shall include for -

FORMWORK

a.

b.

c.

d.

e.





.

.

REINFORCEMENT

a.

b. Rates for reinforcement shall include for -





PRECAST CONCRETE WORKS

a.

i.

ii.

iii

iv.

4. MASONRY WORK

a.

b.

c.





c1

i.

ii.

iii.

iv.

v.

vi.

vii.

c.2

i. ii. iii.iv.

v. vi. vii.

iix.ix.x.xi.xii.

xiii.





c.3

i.

ii. iii.

5. WATER PROOFING

a.

b.

c.

d.

e.

f.

6. STRUCTURAL STEELWORK

7. METAL WORKS

a.

b.

c.

d.













8. ROOF COVERING AND ROOF PLUMBING

a.

b.

9. CARPENTRY(Roof and ceiling frame)

a.

b.

c.





d.

e.

f.

10. JOINERY

a.

b.

c.

d.





f.

g.

11. WALL,FLOOR AND CEILING FINISHES

a.

b.

.



.



c.

d.

12. GLAZINGa

b.





13. PAINTING AND DECORATING

Note

a.

b.

c.

d.

14. PLUMBING

a.

b.

c.

d.

e.



f.



g.

h.

j.

k.

l.

m.

a.

b.

c.

d

e

DRAINAGE WORK

a.

b.

c.



d.



15. ELECTRICAL INSTALLATIONS

a

b

c

d

e

f

g

h

j

k





l

m

n

p

q

r

s

p



PRICING PREAMBLES

1. GENERAL

The Bidder shall refer to the relevant Clauses of Pricing Preamble when pricing composite item of works.

The rate for each item shall also include for all the following -

i. Labour and all connected costs ;

ii. Materials and goods including all connected costs;

iii. Preparatory works and setting out of particular item ;

VI. Plant and equipment unless otherwise included in Preliminaries ;

vii. Handling of materials and working in situation where there is very restricted working space or no working space ;

viii. Square cutting and Waste of materials ;

ix Forming of ends, angles, miters and junctions between straight and raking or curved work ;

x. Protecting and cleaning ;

The Bidder shall read and be conversant with the full description of workmanship and materials as described in the Particular Specification and ICTAD Specification for the respective items of work/ trades prior to the preparation of the Bid.

The rate for each item must be comprehensive and must include for complying in all respects with the requirements of

the aforesaid specifications, these Pricing Preambles, cover all the obligations under the Contract, and all matters and

things necessary for the proper construction, completion and maintenance of the Works. No claim for additional

payment shall be allowed for any error or misunderstanding by the Contractor of the work involved.

iv. Complying with regulations of the Municipal Council and/or any other relevant authority under which particular item of

work is to be executed unless otherwise included in the Preliminaries ;

v. Fitting and fixing materials and goods in position, including hoisting to any height or lowering to any depth and all temporary works, equipment and small tools ;

xi. All other incidental works and necessary works which are not described in the Maintenance Programme, but described in the aforesaid specifications and or shown in the drawings for the proper completion of the relevant item of work ;



Contd.,



2. EXCAVATION AND EARTHWORK

All works under this section are measured net and no working space is allowed.

Dewatering has been measured under Preliminaries.

Rates for Excavation & Earthwork shall include for -

i. Accepting site as found and preparing to condition suitable for proper execution of the Works

iii. Trimming sides, keeping clean and consolidating bottom of basement, sumps, pits and trenches ;

iv. Backfilling and disposal of surplus excavated materials as specified and directed ;

v. Any necessary additional works required due to a. Working space required by the Contractor ; b. Earthworks supports ; c. Formwork ;

xii.Establishment charges and overheads( not included in preliminaries or anywhere in the Bill Of Quantities), and profits.

In addition to above, the rates for items of work in Substructure shall include for the works at depths extending below

ground water table where applicable including excavation under water, removal and disposal of mud and sand and

preparation of place to a condition suitable for proper execution of the works.

The Contractor shall be responsible for the design and execution of the excavation method which is subject to scrutiny

by the Engineer. However, scrutiny by the Engineer shall not in any way relieve the contractor of his responsibilities and

duty of care.

Existing ground levels shown in the Drawings have been taken at the surface of the ground, with no particular differentiation to indicate buried foundations, pavings etc.

The Contractor shall note that the rate for compacted earth fill and granular fill, stone, gravel and sand beds shall include for imported materials or materials from borrow areas.

ii. Excavating by whatever means are necessary including excavation done manually or by machine in any type of ground including ground with boulders (except rock) and excavation around existing RCC. bored piles and jet grout piles ;

vi. Any additional trimming or appropriate backfilling to provide specified or approved formations and profiles

necessitated by the uneven excavation of the earth, unless otherwise measured separately ;



Contd.,



3. CONCRETE WORK

Rates for concrete work shall include for -

i. Mixing as per specification, depositing, handling, hoisting and placing at any height or depth ;

iii. Packing and tamping around reinforcement, including vibrating ;

iv. Contractor's designed kickers, construction joints and sealants ;

vi. Curing ;

FORMWORK

Rate for formwork shall include for -

i. Fabricating setting up and erection at any height or depth ;

Rates for compacted earth fill, granular fill and gravel and sand beds shall include for finishing sub-grade to slopes and

falls, depositing in layers, leveling, blinding, and machine or hand-packing to form vertical or battered or level faces,

and for forming sinking where required under floor slabs or sub-floor layers.

Rates for approved damp-proof membrane shall include for laps, and straight, raking and circular cutting, and for notching around all obstructions.

ii. In case of readymix concrete, transporting, admixtures, handling, pumping/hoisting and placing at any height or depth ;

v. Finishing to slopes and falls, and preparing surface ready for screeds or paving, where necessary, including cutting to

sizes and temporary supports to form necessary grooves ;

vii. Preparation of ground surface, grading to slope and falls, if any, and machine or hand packing to form vertical or battered or level surface and all necessary formwork to edges of blinding concrete in case of pile caps ground slab/ramps/beams.

Formwork for similar concrete members are measured together irrespective of the height or depth and the shape or form.

Extra-over rate for a particular type of high quality formwork should be applied only for the areas of formwork which requires such high quality type formwork as specified.

Formwork shall be properly designed and strictly as described in the specifications for the particular type of concrete surface finish and it should be sufficiently strong and grout tight.

Faces of Jet grouting piles, masonry and concrete work which will be formed or used as formwork shall not be measured as formwork and no payment shall be made for same.



Contd.,



iii Coating with shuttering oil and or lining ;

iv Easing, striking and removing ;

v. Cleaning, preparing for reuse ;

vi. Removal when no longer required ;

vii. Props, stays, struts, wedges, bolts, incidental items and materials such as nails, screws anchors hooks etc. ;

viii. All overlaps and passing at angles ;

ix. Labour at intersections and narrow widths ;

x. Rubbing down and making concrete surface good after removal of formwork ;

xii. Providing samples as required by the Engineer of the different formed finishes specified.

REINFORCEMENT

i. Standard length of reinforcing bar for the purpose of measurement shall be 6.0 m.

ii. Payment for bar reinforcement shall be to be nearest L.ft/ Cwt..

i. Rolling margin ;

ii. Preparation of bar bending schedules (Including laps);

iii. Straightening as required and cleaning of bars ;

iv. Cutting, bending and binding ;

v. Hoisting and placing in position at any height or depth ;

vi. Binding wires, and cover blocks.

vii. Necessary supports such as chairs and spacers.

viii. Aligning and supporting in position during concreting.

ii. Strutting, supporting through lower floors and supporting at any level, including additional propping, strutting and supporting decks ;

xi. All fillets, to form grooves, rebates and throats, splays or chamfers, raking and circular cutting, and cutting around all

pipes, sleeves, conduits, ducting, metal sections and fittings ;

b. Rates for reinforcement shall include for -



Contd.,



PRECAST CONCRETE WORKS

Rates for precast concrete works shall include for -

The requirements of the Pricing Preamble clauses which refer to Concrete Work, Reinforcement and Formwork.

Loading, transporting to Site, unloading, handling and stacking.

Hoisting and fixing in position at any height or depth.

4. MASONRY WORK

Rates for brickwork/Block work shall include for -

i. Plumbing, angles, straight cutting, forming rebates, reveals and raking out joints for plastering;

iv. Supplying and fixing metal clamps, Galvanized, steel boundary ties, and brick reinforcement etc.;

v. Necessary cutting required in walls which are not multiples of brick size ;

vi. Preparing existing walls for raising and pinning new brickwork ;

vii. Bonding new walls to concrete faces and old walls where necessary, and materials to be used for such bonding.

Rates for Damp Proof Course shall include for -

i. Necessary leveling screed and trimming top of rubble/block/brick plinth wall ;

Moulds and for formwork with the required finish to all exposed surfaces in accordance with the specifications, hacking

surfaces to form key for rendering etc., and hoisting to any height or depth including providing any lifting holes or other

devices to the approval of the Engineer, building in, including bedding and jointing in mortar as required, and any

necessary strutting and supporting.

In the calculation of the volumes of brick wall which are not multiples of the size of standard bricks, the thickness of

such walls shall be taken as the thickness of full bricks from which they can be cut. The same principle of calculation of

volume shall be used for all brickwork of which the cross-sectional dimensions are not multiple of brick sizes.

ii. Splay cutting, rough cutting, fair cutting, forming chases or grooves for slabs, partitions, staircases, roofs and the like,

bonding ends of walls, building in or cutting and pinning in and making goods on lintels, timber and steel works ;

iii. Building at any level or height of slabs or beams, additional labour in kerbs, isolated and attached piers, all cutting,

bonding at angles and intersections, building into or against adjacent work, wedging and pinning up to soffits;



ii. Fair edges, rounded edges, drips and arises, angle fillets ;Contd.,



iii. Turning nibs of asphalt into grooves ;

iv. Cutting to line and jointing new to old asphalt.

Rubble work

Rates for Rubble Masonry shall include for -

All joggles, cramps, dowels, ties, templates ;

Bonding ends of walls, rough cutting and fair cutting ;

Leveling up in walling for Damp Proof Courses, sills, thresholds, string courses, copings and the like ;

Forming straight vertical joints next to dressings, panels, brickwork etc. ;

Forming openings and dressed margins ;

Rates for stone work shall include for:-

Extra material for curved work All rough and fair cutting Dressing Forming rough and fair grooves, throats, mortices, chases, rebates, holes, stops and miters.

Raking out joints for key Labours in eaves filling Dressed margins to rubble work Leveling uncoursed work Rough and fair square cutting Centering Wedging up and pinning to concrete soffits and steel work Building in frames, flashing, damp proof courses including filling hollows of corner blocks with mortar

Building in ties, lugs, plates, lintels, pipe sleeves, inserts, switch boxes and the like. As the work proceeds.

Rubble Stone masonry built of stones either irregular in shape as quarried or shaved and only hammer dressed and having comparatively thick joints.

Plumbing, angles, fair returns, setting, jointing, eaves filling, pointing and fixing in position, hoisting to any given height or depth ;

Forming chases, throats, rebates, margin flutes, sinking, chamfered and rounded edges, and all labour connected therewith.

Ashlar Stone masonry using dressed stone blocks of given dimensions having faces perpendicular to each other and laid in courses.



Contd.,



Stone Veneering work (Face rubble work)

Stones cut into slabs of required thickness.Dressed to very close tolerances.

5. WATER PROOFING

Rates for Water Proofing shall include for ;

For necessary leveling and trimming top of rubble/block/brick plinth wall ;

Fair edges, rounded edges, drips and arises, angle fillets ;

Forming internal and external angles, bonding bricks/blocks and the like ;

Turning nibs of asphalt into grooves and asphalting around brackets ;

Cutting to line and jointing new to old asphalt ;

Temporary screeds, ground and rules.

6. STRUCTURAL STEELWORK

Rate shall include for :

7. METAL WORKS

General Notes for Metal works

Contractor to prepare shop drawings for approval of the Engineer.

Fabrication & fixing of Aluminum components

Material

Stone lining upto 80mm along planes parallel to natural bed. The natural bed may be masonry of brickwork or rubble work, concrete surface.

All shop fabrication work, including cutting, drilling, bolting, riveting, welding, grinding, delivering, unloading, hoisting, erecting and fixing.

Type and quality of steel to be used for metal work shall be as per drawings and relevant specification clause and or shall conform to latest British Standards.

Rates for Metal Work shall include for anchors, screws, dissimilar metals and providing thermal movement and the

preamble clauses for Structural Steel Work where relevant and they shall apply equally to relevant items of this section.

Fabrication & fixing of Aluminum components shall be carried out by experienced tradesman. The Contractor shall

furnish particulars of Aluminum fabricator through the engineer for his approval.

The Contractor will be required to furnish a guarantee on material and workmanship for a period of 8 years from the date of handing over of Works in the form required by the employer, binding the Aluminum manufacturer and the Contractor jointly and severally



Contd.,

All Aluminium sections shall be fully treated extruded Aluminium alloy sections in accordance with BS 1470,1471, 1473, 1474 or latest relevant EN standard



FinishAll Aluminium extrusions shall be accordance with the Manufacturers Mill report.

(1 ) Anodizing or( 2 ) Powder coating ( What ever specified in Aluminium Items )

Rate for Aluminum doors and windows shall include for

i. Glass and glazing

ii. All necessary ironmongery (defined)

iii. Furnishing shop drawings

iv. Furnishing guarantee's as required by the employer

v. Sampling and submission of test reports to the engineer as directed

Screws and Hardware Items

Hardware items such as Hinges, Handles, Catches, fixtures etc., shall be minimum of grade 304 stainless steel.

Glass

WorkmanshipThe fabrication and installation of all Aluminium work must be carried out by specialist tradesmen.

All Aluminium sections shall present clear, straight and sharply defined lines. They shall be free from defects impairing strength, appearance and durability.

All members shall be finished either by

Anodizing -Exposed surface of all members shall be anodized using two steps. Anodizing process to an anodic thickness of not less than 10-15 microns and shall be free of any defects.

Powder coating - Powder coating shall be carried out using polyester coating with proper and appropriate pre- treatment to a coating thickness of not less than 60-80 microns, measured on all significant surfaces.

Concealed screws, nuts, bolts, rivets and other fastening devices shall be of Aluminium, non-magnetic stainless steel or other approved corrosive resistant materials. If visible, they shall blend with the finish of the framing Aluminium sections.

Glazing shall be minimum of 5mm thick clear float glass. Glass shall be secured at all edges with compression gaskets and glazing beads. When fixing glass, all glazing sealant shall be carefully applied and cleaned off properly.

All dimensions shown on the drawings and the shop drawings must be verified by actual site measurement before fabrication and installation. Any cutting to enlarge the size of openings and approved practical method to fill the excess void behind frames required after installation shall be executed by the Contractor at his own expense.

All Aluminium members shall be factory fabricated to the best standard of workmanship under experienced factory supervision and control.



Contd.,



Submissions

- full size sections of members- methods of assembly- methods of glazing- methods of installation, including fixings caulking, flashing- provisions for vertical and horizontal expansion- junctions and trim to adjoining surfaces- fittings and accessories

Doors & Windows

Aluminium Louvers

The Contractor shall provide a guarantee in respect of the weatherproof properties of the fixed louvers.

Partitions

Materials, method of fabrication, assembly, installation, fastenings, supports, braces, operating parts and the like shall be in accordance with the approved shop drawings.

All joints in frames at corners, junctions and intersections shall be mechanically jointed and be such that when assembled they are as strong and rigid as adjoining sections. Due care must be taken to ensure that all joints are water tight and leak-proof. Joint lines should not be visible.

Provisions must be made for expansion and contraction in horizontal and vertical members which are exposed to the weather or environments. Any distortion of members or any glass cracked or broken as a result of inadequate provisions must be rectified by the Contractor at his own expenses.

All works shall be securely installed and anchored in position, set plumb, square and level in accurate alignment with other work, all in accordance with the approved shop drawings to the Engineer's satisfaction.( The allowable tolerance in terms of specified dimensions shall be plus/minus 1.5mm.)

The Contractor shall submit shop drawings showing the following information where appropriate to the item ; layout (Sectional plan and elevation) of complete assembly

The Contractor shall submit certificates from the Aluminium manufacture and/or an approved testing laboratory which attest that the coating thickness offered is as specified.

Frame and /or sash sections shall be of extruded EN-AW 6063-T5 Aluminium Alloy having a normal thickness of 1.5mm

( Accepted commercial tolerance of tolerance of ± 0.15mm shall apply )

Fixed louvers shall be of the weather proof type, suitable for overcoming water carried- over by wind and the fixed louvers shall have free areas of not less than 50%

All powder coatings shall match the windows. Panels shall be so constructed as to be completely weather proof at junctions with adjoin structures .



The frames shall be properly machined no permit easy assembly and to form weather-tight joints when caulked.

Partition members shall be 76mm in depth and the thickness of 1.2mm.Contd.,



Following dimensions are applied for the frame members of each assembly units

Assembly Unit Member Depth Mini. Member Thickness

(mm) (mm)Casement Window, Fanlight 41, 60, 70 1.2

Sliding door/Window 70, 80, 100 1.2

Door 100 1.5

8. ROOF COVERING AND ROOF PLUMBING

Rates for roof covering and roof plumbing shall include for :

i. Hoisting, placing and fixing in position ;

ii. Straight cutting, raking cutting, circular cutting, notching, and working around obstructions and waste ;

iii. Nails, screws and the like ;

iv. Drilling and making holes or opening and the like;

Rates for flashings shall include for the following in addition to the requirement of "a" above -

i. Bending and cutting to required shape and forming roll edges ;

ii. Angles, edges and ends ;

iii. Notching over roofing ribs or dressing into roof cover/concrete as the case may be ;

iv. Forming and dressing into or around walls at obstructions and the like ;

v. Stepping up ;

vi. Sealing with sealant materials.

9. CARPENTRY(Roof and ceiling frame)

Sizes of all timber given are finished sizes.

All timber shall be well seasoned and treated against insect and termite attack beforefixing in position

Rates for carpentry shall include for -

Rates shall include for all necessary hinges, screws, rubber beadings, Skelton bolts, Aluminium louvers, pinhead stickers, etc.

i. Any type of cutting required, sawing, notching, drilling, trimming, framing, jointing, splayed edges and the like,

hoisting and fixing in position with nails, spikes, plugs, screws, and gluing and priming to joints and ends ;



Contd.,



ii. Forming splayed edge, grooves, chamfers, scribed and rounded edge, beveling, molding and the like ;

iii. Plugging, wedging, nuts and washers with bolts, sprockets and pins and the like ;

iv. Nogging or solid bridging, cut between studs or joints for structural timber.

v. Rebating, singings, grooving, mortising ;

vi. Additional timber lengths required for carpentry jointing ;

vii. Protection and keeping clean for staining, polishing or painting where applicable ;

10. JOINERY

Sizes of all timber given are finished sizes.

All timber shall be well seasoned and treated against insect and termite attack before fixing.

Rates for Joinery shall include for -

iii. Working to stated sizes, for all short lengths making miters, joints and ends ;

iv. Necessary bolts, dowels metal clips, anchors, grips and fixing joinery ;

v. Gluing, dowelling, plugging, wedging pining and the like ;

vi. Punching heads and filling with approved filler if nails or pins are used for fixing ;

Rates for roof decking shall include for machine sanding, protecting and preparing in addition to the requirements c above.

Rates for walls and ceiling lining shall include for jointing and fixing to walls/ ceiling/ eaves etc. all cover and joint strips, in addition to the requirements c above.

Rates for timber paneling/wall lining shall include for cover moldings, sills, stiles and head moldings to openings as relevant.

Timber used for joinery works shall be well seasoned well treated and in one species of special class timber

recommended for the particular class of Joinery works as specified in the Specification.(Quality should be assured

through Sampling and test reports)

i. Any type of cutting required, sawing, notching, drilling, trimming, planning, forming and jointing and the like, fixing in

position complete with nails, spikes, plugs, screws and gluing and priming to joints and ends ;

ii. Forming splayed and tongued edges, rebates mortises, grooves, chamfers, scribed and rounded edges, beveling,

moulding, margin and the like and rounded corners, sinkings ;



vii. Countersinking and filling heads with approved filler, if brass screws are used for fixing ;

Contd.,



viii. Painting rebates of frames before fixing glass ;

ix. Bedding in cement mortar filling and hanging to frame lining ;

x. Keeping clean for staining, polishing or painting;

xi. Painting, Lacquering or Varnishing as specified.

Preambles for Glazing section and a, b and c under Painting and Decorating section shall

equally apply to Joinery works.

Ironmongery

i. All cutting, fitting, sinking, boring, mortising ;

ii. Matching screws for ironmongery

11. WALL,FLOOR AND CEILING FINISHES

Rates for wall, floor, ceiling finishings and wall floor screed and bedding shall include for -

iii. Tamping and compacting ;

v Forming internal and external angles and arises ;

vi. Any extra thickness required to finish to true levels ;

iii Removing during decoration, refixing after decoration, leaving oil and in proper working order on completion and

supplying and labeling all keys and handing over to Employer.

i. All works under this trade shall be measured in Sq.ft/ Sqr. after deduction for voids, openings, doors and windows

ii. All other small quantities/panels/narrow widths/ arises/ reveals/ angles/ ends/short lengths including those of tiling

work on door and window jambs and reveals are measured together with the respective tiling item and labour in such

work shall be included in the rate for the main finishing item and they shall not be measured/paid separately.

i. All temporary rules, screeds, templates and supports, curing and cleaning off on completion and exact thickness required to finish ;

ii. Caulked joints and making good and cutting around bolts, pipes conduits, sleeves, ducting, fittings, sections, obstructions and the like ;

iv. Raking out joints of new brickwork/Block work or hacking concrete to form key, including brushing, cleaning off and dampening ;



Contd.,

vii Any additional dubbing out required to plastered surfaces of brickwork and to the finished surface of concrete to obtain the requisite standard of finish ;



viii. Samples to be submitted for the approval of the Engineer.

Rates for tile slab or block finishing to floor and wall shall also include for the following in addition to the above -

i. Straight raking and circular cutting ;

ii. Dubbing out or packing to concrete surface to correct deviations within specified tolerance ;

iii. Laying or finishing to falls or cross falls ;

iv. Expansion joints at perimeter and between bays where required in case of floor tile paving ;

v. Sand blasting, cleaning, waxing and appropriate floor finishings.

Rates for ceiling lining shall include for the following

i. Working to sides and soffits of attached or isolated beams and soffit of staircases where relevant;

ii. Additional forming required for lighting and air-conditioning grills ;

iii. Straight, raking and circular cutting ;

iv. Neoprene sealing for air tightness around hatches if any ;

v. Matching edges where cutting occurs and for filling the heads of fixings with approved filler where relevant ;

vi Painted mild steel hanging rods.

12. GLAZING .i. Type of Glazing shall be as specified.

Rates for Glazing shall include for -

i. Glazing, fixing, bedding priming and panel pins and other materials and labour for same and cutting to size ;

ii. Templates, straight cutting, circular cutting, grinding edges or special type of edges required and sand blasting ;

iii. Glazing beads, washlether or neoprene strip, glazing sealant, weather stripping, caulking joint silicone joint ;

iv. Replacing cracked or broken glass ;

ii. Thickness of glazing shall be as per the design of the approved specialist contractor who will be engaged by the

Contractor. However, the minimum thickness shall be 6mm, unless otherwise stated.



Contd.,



v. Making holes where necessary ;

vi. Samples to be submitted for the approval of the Engineer.

13. PAINTING AND DECORATING

NoteColour and the quality of all paint and other painting materials shall be approved by the Engineer prior to use.

Rates for painting shall include for -

i. Preparation of surfaces, cleaning down, smoothing, etc. ;

ii. Submission of samples for the approval of the Engineer ;

iii. Protection of floors, walls and fittings etc. ;

v. Cleaning down upon completion

14. PLUMBING

The rates for Plumbing shall include for :

Refer specifications for full description of materials and workmanship.

Short lengths, joints connections and couplers in running length.

Sealing, fixing and support with holder bats or pipe clips cut and pinned built in wall or slabs.

Plugging screwing to walls or ceiling

iv. Working to returns, painting in any colour, multi- colour works, cutting into line at junctions of different colours at angles or plain surfaces, painting in small quantities ;

Rates for work to isolated general surfaces shall include for working on door frames, linings, window sub frames (where

of a differing material to the window), skirting, rails, architrave's, bars, posts, balusters and the like.

Rates for work to glazed general surfaces, glazed windows and the like (measured both sides, flat over glass,

irrespective of size and panes) shall include for work to edges and glazing rebates, returns and moldings of frames,

mullions, transoms, architraves and the like.

Rates for work to pipes and conduits (which shall include trunking, ducting and the like) shall include for all work on hangers, supports, brackets and the like.

Screws, nails, sockets, connectors, backnuts, nipples, and standard pipe fixing or supporting clips, saddles, brackets

straps, screws, nails, solder rivets connectors, flanges pipe sleeves, brackets, made bend holder bats and the like.



All laps, straight cutting and wasteContd.,



Jointing compound, solvent cement and incidental materials and labour.

Connecting pipes to sanitary fixtures and appliances.

Testing and disaffection after completion.

Rates for sanitary fittings shall include for

Jointing and or connecting pipes to sanitary fittings.

DRAINAGE WORK

The provisions and the clauses of precedence trades shall equally apply to relevant item of this trade.

The fittings including bends, tees, collars, reducers elbows, valve sockets, junctions, caps and the like for pipe less than or equal 50mm dia pipe.

Standard and special pipe fixing arrangement where necessary fittings, supporting clips, saddles, brackets, holder bats

straps ,rowl plugs, brackets, nails, anchor bolts etc.

All builders works such as chasing and forming holes through brick work/ block work/ foundations and concrete slabs

beams columns floor slabs manholes and like and making good all damages.

Fittings such as taps, waste water outlet, flushing cistern, internal overflows and the like and supporting brackets, incidental materials for fixing.

Assembling, jointing together, fixing components parts and jointing to pipes including necessary coupling and for leaving

perfectly clean undamaged and in perfect working order as on completion.

Any special water supply and drainage fittings such as bends, tees, reducers etc. unless otherwise specified separately

in the Bill of Quantities, shall be deemed to have been included in the relevant items and such items should accordingly

be rated to include for such specials etc. and for any extra work involved and the satisfactory completion of such items.

Where pipes pass through walls or slabs these shall be wrapped with a layer of inert materials. For pipes exceeding 50

mm dia sleeve pipes shall be used for the full thickness of slabs, walls or beams through which the pipes pass.

The rates for trench excavation for pipes shall include for depending and widening the trench as necessary to enable

the barrels of pipes of rest on firm and to facilitate jointing.

The rates for rock excavation in trench excavations shall include for importing selected materials to replace any

excavated rock which is unsuitable for back filling and for all additional rock excavation and appropriate filling beyond

the maximum measurable in accordance with the specification.



The rates for concrete beds and surrounds to pipes shall include for flexible joints and any necessary formwork where required by the specification.



15. ELECTRICAL INSTALLATIONS

The rates for cables and the like laid in benches shall include for drawing through conduits or ducts where required.

The execution of Electrical Installation shall every respect comply with the current Regulations of the Institute of

Electrical Engineers, London, requirements of Ceylon Electricity Board and the area Authority.

The rates for equipment and control area, distribution boards, meters, switches, fuses, etc. shall include for connecting

up, fixings and supports for the complete installation and for suitable mounting boards, frames, supports, housings and

cabinets where required.

The rates for cables, tape, bus-bar trunking etc. (except where included in sub circuits or electrical points) and the like

shall include for joints in the running length, all allowances for sagging snaking, for drawings through conduits, laying in

trunking of surface fixing where retired with cable supports, clears, hangers, channels, insulators and the like.

The rates for cable terminations shall include for all connections point boxes, insulating and jointing materials, cable terminations glands, lock nuts, bushes and the like.

The rates for conduits trunking cable tray etc. (except where included in sub circuits of electrical points) and the like

shall include for all short lengths, joints and couplers in the running length, and for all fixings and supports with

approved saddles, crumpets, clips and the like cut and pinned, built-in or plugged and screwed to walls or ceilings

including chasing brick work, block work, concrete slab beams walls columns and the like and make good.

The rates for conduits and the like shall include for all bends, tees, socket and the like, cutting, screwing, threading,

jointing and providing all conduit boxes, junction boxes and the like.

The rates for the installation of sub main circuits, lighting points switched points, socket outlets, fused spur outlets,

isolators, etc. (other than those applicable to the distribution switch gear) shall include where applicable, for all conduit,

trunking, cable tray, cabling, terminations, fixings and connections from the distribution switched gear to and including the point (accessories measured separately) and shall be deemed to include for any

item mentioned in the Electrical installation Specification but not shown on the drawings and vice-versa.

The rates for lighting fittings, fittings such as ceiling fans and extract fans, and for appliances such as air- conditioning

units shall include for assembly, fixing and connection from the spur outlet or isolator to the fitting or appliance with all

necessary additional wiring earthing and outlet roses and leaving perfectly clean and undamaged on completion.

The rates for fixing only fittings and appliances provided by the employer should include in addition to the foregoing for

accepting delivery, storing and handling the fittings and providing any additional materials and internal wiring.



Contd.,



The rates for power outlets shall include for mounting boxes and frames.

The rates for power switched with remote outlets shall include for the additional outlet plates and boxes.

The rates for switched socket outlets shall include for 1 No fused plug top and 4 No fuse links.

Painting of timber work and metal work.

i. The preceding clauses of this trade where relevant.

ii. Preparation of as built drawings to be submitted to Employer at the handingover/ practical completion.

iii All items and accessories required for proper installation as per specification and regulation up to load point and labour connected therewith.

iv. All wiring, conducting and cables and labour connected therewith if not measured separately.

v Items specified in the specification but not shown in the drawings.

vi Disconnecting and refixing of electrical fitting and appliances as required for the convenience of other trades.

vii Painting of timber work metal work executed under this trade.

Rate to include submission of Megar Test report of the building Electrical Installation from Charted Electrical Engineer

The rates for connections only to fittings and appliances such as pumps, water heaters, air conditioning units and

extract fans shall include for connection from the isolator or spur outlet to the fitting or appliance (these being measured

separately) , with all necessary additional wiring, earthing and outlet roses.

The preceding preambles shall apply equally to auxiliary installations such as TV installations, telephone installations, and bell signal systems.

If the items of electrical installation are measured as sub circuit point wiring or in electrical points, the rates for such items shall include for :



PRELIMINARIES

1

2 Necessary protective fencing, lighting, watchmen and other precautions.

3

4 Erection of temporary sheds for protection and storage of materials and plants.

5 Temporary sheds and sanitary accommodations for workmen.

6 Setting out works

7 Insurance against workman's compensation.

8 Insurance against accidents and injury to workmen , property , material work .

9 Insurance of materials and work at site.

10 Cost of preparing bid.

11 Cost of stamps etc. for contract agreement.

12

13 Erection of Notice Board.

14 Supply of water for use in the work.

15 Charts , Schedules and the like showing time progress, organization of trades of similar matters.

16 Temporary electricity to site

17 Payment of pay roll, sales , receipts and other taxes.

18 Temporary roads , tracks, crossings, planked footways and the like and maintenance.

19 Expenses in connection with general foreman and other site staff.

20 Expenses in connection with security bonds, performance bonds, guarantees, mobilization fees, etc.

21

The preliminaries given below have been considered for the rates in the items of various trades in the Building Shedule of Rates.

Giving notices to authorities etc. Payment of fees , compliance with by lows and regulations lawfully imposed by local authorities.

Erection of 1 Nr. Temporary office with sanitary and electricity facilities for the use of person acting on behalf of the employer.

Removal of all rubbish and debris, clearing up the site and leaving building clean internally and externally.

Extra Payment on labour losses in connection to workmen where required for special conditions, distant camping, dirty work and the like.





22 Losses rising from restriction to site.

23

24 Erecting, maintaining and dismantling scaffolding.

25 Attendance upon, cutting away for and making good after all trades.

26

27

28 Liability of the builder for making good defects after practical completion.

29 Safety of workers - Safety nets, boots, helmets, head gears , safety goggles etc.

Attendant labour and Hire of plant and equipment such as Weter pump with necessary accessories for working order.Welding Plant, Hammer drill, Jack hammer, Compressor etc.

Protecting and safeguarding the works, materials and plant against the effect of the weather and against damage, trespass or theft.

Duties of the builder on completion including such matters as cleaning and leaving all in good order, labeling over keys, handing over certificates, guarantees and the like.



Necessary protective fencing, lighting, watchmen and other precautions.

Erection of temporary sheds for protection and storage of materials and plants.

Temporary sheds and sanitary accommodations for workmen.

Insurance against accidents and injury to workmen , property , material work .

Insurance of materials and work at site.

Cost of preparing bid.

Cost of stamps etc. for contract agreement.

Erection of Notice Board.

Supply of water for use in the work.

Charts , Schedules and the like showing time progress, organization of trades of similar matters.

Temporary electricity to site

Payment of pay roll, sales , receipts and other taxes.

Temporary roads , tracks, crossings, planked footways and the like and maintenance.

Expenses in connection with general foreman and other site staff.

Expenses in connection with security bonds, performance bonds, guarantees, mobilization fees, etc.

The preliminaries given below have been considered for the rates in the items of various

Giving notices to authorities etc. Payment of fees , compliance with by lows and regulations lawfully

Erection of 1 Nr. Temporary office with sanitary and electricity facilities for the use of person acting on

Removal of all rubbish and debris, clearing up the site and leaving building clean internally and

Extra Payment on labour losses in connection to workmen where required for special conditions, distant



Contd.,



Losses rising from restriction to site.

Erecting, maintaining and dismantling scaffolding.

Attendance upon, cutting away for and making good after all trades.

Liability of the builder for making good defects after practical completion.

Safety of workers - Safety nets, boots, helmets, head gears , safety goggles etc.

Attendant labour and Hire of plant and equipment such as Weter pump with necessary accessories for

Protecting and safeguarding the works, materials and plant against the effect of the weather and

Duties of the builder on completion including such matters as cleaning and leaving all in good order,


S07- 25

A001

A002A003

A004

A005A006A007

A008

A009

A010

A011

A012

A013

A014

A015

A016A017A018

A019A020

A021

A022

A023

Item Code

Author: Eng. D.N.Ranaweera


S07- 26

Item Code

A024

A025

A026A027

A028

A029

A030

A031

A032

A033A034

A035

A036

A037

A038

A039

A040

A041

A042

A043

A044


S07- 27

Item Code

A045


S07- 28

Item Code

A046

A047

A048

A049

A050

A051


S07- 29

Item Code

B001

B002

B003

B004

B005

B006

B007

B008B009B010B011B012

B013

B014

B015

B016

B017


S07- 30

Item Code

B018

B019

B020

B021


S07- 31

Item Code

C001

C002

C003

C004

C005

C006

C007

C008

C009

C010

C011

C012

C013

C014

C015

C016


S07- 32

Item Code

C017

C018

C019

C020

C021

C022

C023

C024

C025

C026

C027

C028

C029

C030

C031

C032

C033

C034

C035

C036


S07- 33

Item Code

C037

C038

C039

C040

C041

C042

C043C044C045

C046

C047

C048

C049

C050

C051

C052


S07- 34

Item Code

C053


S07- 35

Item Code

D001

D002D003

D004

D005D006D007

D008D009

D010D011D012D013

D014

D015

D016

D017

D018

D019

D020

D021

D022

D023

D024


S07- 36

Item Code

D025

D026

D027

D028D029D030D031


S07- 37

Item Code

E001E002E003

E004

E005

E006

E007

E008

E009

E010


S07- 38

Item Code

F001F002

F003

F004

F005

F006

F007

F008F009F010F011

F012

F013F014

F015F016F017


S07- 39

Item Code

F018F019F020F021

F022F023F024

F025F026F027

F028F029

F030

F031

F032

F033

F034

F035F036


S07- 40

Item Code

F037


S07- 41

Item Code

F038F039F040F041F042

F043F044F045F046

F047

F048

F049

F050

F051

F052

F053F054

F055

F056


S07- 42

Item Code

F057

F058

F059

F060

F061

F062

F063

F064

F065

F066

F067F068

F069


S07- 43

Item Code

F070

F071

F072


S07- 44

Item Code

G001

G002

G003

G004

G005

G006

G007

G008

G009

G010

G011

G012


S07- 45

Item Code

G013

G014

G015

G016

G017

G018

G019

G020

G021

G022

G023

G024

G025

G026

G027

G028

G029

G030


S07- 46

Item Code

G031

G032

G033

G034G035G036

G037

G038

G039

G040G041

G042

G043

G044G045G046G047G048

G049G050G051G052

G053


S07- 47

Item Code

G054

G055

G056

G057

G058

G059

G060

G061


S07- 48

Item Code

H001

H002

H003

H004

H005

H006

H007

H008

H009

H010

H011

H012

H013

H014

H015


S07- 49

Item Code

H016

H017H018

H019

H020

H021

H022

H023H024

H025

H026

H027

H028

H029


S07- 50

Item Code

H030H031

H032

H033

H034

H035

H036

H037

H038

H039

H040

H041

H042

H043

H044


S07- 51

Item Code

H045

H046

H047

H048

H049

H050

H051

H052

H053

H054

H055

H056

H057

H058H059H060

H061

H062

H063


S07- 52

Item Code

H064

H065H066


S07- 53

Item Code

H067

H068

H069

H070

H071

H072

H073

H074

H075

H076

H077

H078

H079


S07- 54

Item Code

H080

H081

H082

H083

H084

H085

H086

H087

H088

H089

H090

H091

H092

H093

H094


S07- 55

Item Code

H095

H096

H097

H098

H099

H100

H101

H102

H103

H104

H105

H106

H107

H108

H109

H110

H111H112

H113


S07- 56

Item Code

H114

H115

H116

H117

H118

H119

H120H121H122

H123

H124


S07- 57

Item Code

J001J002J003

J004

J005

J006

J007J008J009J010J011J012

J013

J014

J015

J016

J017J018J019J020J021

J022J023

J024


S07- 58

Item Code

J025J026

J027J028J029

J030

J031

J032

J033

J034

J035

J036

J037

J038

J039

J040

J041J042

J043

J044

J045


S07- 59

Item Code

J046

J047

J048

J049

J050

J051

J052

J053

J054

J055J056

J057J058J059J060J061

J062

J063

J064

J065

J066

J067

J068


S07- 60

Item Code

J069

J070

J071

J072

J073J074

J075

J076

J077

J078

J079

J080

J081

J082

J083

J084


S07- 61

Item Code

J085

J086

J087

J088

J089

J090

J091

J092

J093

J094


S07- 62

Item Code

J095

J096

J097

J098

J099

J100

J101

J102

J103

J104

J105


S07- 63

Item Code

K001

K002

K003

K004

K005

K006

K007K008K009K010

K011

K012

K013

K014

K015

K016

K017

K018

K019K020K021

K022

K023


S07- 64

Item Code

K024

K025

K026

K027

K028

K029

K030

K031

K032K033

K034

K035

K036K037K038

K039K040

K041K042K043

K044K045

K046

K047


S07- 65

Item Code

K048

K049

K050

K051K052K053

K054

K055

K056

K057

K058


S07- 66

Item Code

L001

L002

L003

L004

L005L006L007

L008

L009

L010

L011L012

L013

L014

L015L016

L017L018L019L020L021L022L023L024

L025

L026


S07- 67

Item Code

L027


S07- 68

Item Code

L028

L029

L030

L031

L032

L033L034


S07- 69

Item Code

M001

M002

M003

M004

M005M006M007

M008

M009

M010

M011

M012

M013

M014M015M016M017M018

M019

M020

M021


S07- 70

Item Code

M022

M023

M024M025

M026

M027

M028M029

M030

M031

M032

M033

M034

M035

M036

M037

M038

M039


S07- 71

Item Code

N001

N002

N003

N004

N005

N006


S07- 72

Item Code

P001

P002

P003

P004

P005

P006

P007

P008

P009

P010

P011

P012

P013


S07- 73

Item Code

P014

P015

P016

P017

P018

P019

P020

P021

P022

P023

P024

P025

P026

P027

P028

P029

P030

P031

P032


S07- 74

Item Code

P033

P034

P035

P036

P037

P038

P039

P040

P041

P042

P043

P044

P045

P046

P047

P048


S07- 75

Item Code

P049P050P051


S07- 76

Item Code

P052

P053

P054P055

P056

P057

P058

P059

P060

P061

P062

P063

P064

P065

P066

P067

P068

P069

P070


S07- 77

Item Code

P071


S07- 78

Item Code

P072

P073

P074

P075

P076


S07- 79

Item Code

Q001Q002Q003Q004

Q005

Q006Q007Q008Q009Q010

Q011

Q012Q013

Q014

Q015Q016

Q017

Q018

Q019

Q020


S07- 80

Item Code

Q021

Q022

Q023

Q024

Q025

Q026

Q027

Q028

Q029

Q030

Q031

Q032

Q033

Q034

Q035

Q036

Q037Q038Q039Q040Q041Q042

Q043Q044Q045


S07- 81

Item Code

Q046

Q047

Q048

Q049

Q050

Q051

Q052

Q053

Q054

Q055

Q056

Q057

Q058

Q059

Q060

Q061

Q062

Q063Q064


S07- 82

Item Code

Q065Q066Q067Q068Q069


S07- 83

Item Code

Q070

Q071

Q072

Q073

Q074

Q075

Q076

Q077

Q078


S07- 84

Item Code

Q079

Q080

Q081

Q082

Q083

Q084


S07- 85

Item Code

Q085

Q086

Q087

Q088

Q089

Q090

Q091

Q092


S07- 86

Item Code

Q093

Q094

Q095

Q096

Q097

Q098

Q099

Q100

Q101

Q102

Q103

Q104

Q105


S07- 87

Item Code


S07- 88

Item Code

Q106

Q107

Q108

Q109

Q110

Q111

Q112

Q113

Q114

Q115

Q116

Q117

Q118

Q119

Q120


S07- 89

Item Code

Q121

Q122

Q123

Q124

Q125Q126

Q127

Q128

Q129

Q130

Q131

Q132


S07- 90

Item Code

Q133

Q134

Q135

Q136

Q137

Q138


S07- 91

Item Code

Q139

Q140

Q141

Q142

Q143

Q144

Q145

Q146


S07- 92

Item Code

Q147

Q148Q149

Q150

Q151

Q152

Q153

Q154

Q155

Q156

Q157Q158Q159Q160

Q161

Q162


S07- 93

Item Code

Q163

Q164

Q165

Q166

Q167

Q168

Q169

Q170

Q171

Q172

Q173


S07- 94

Item Code


S07- 95

Item Code

Q174

Q175

Q176

Q177

Q178

Q179

Q180

Q181

Q182

Q183

Q184

Q185


S07- 96

Item Code

Q186

Q187

Q188

Q189

Q190

Q191

Q192

Q193

Q194

Q195

Q196

Q197Q198Q199Q200


S07- 97

Item Code

Q201Q202Q203

Q204Q205Q206Q207Q208Q209Q210Q211Q212Q213

Q214

Q215Q216Q217Q218Q219Q220Q221

Q222

Q223Q224

Q225

Q226

Q227

Q228

Q229Q230

Q231Q232Q233Q234Q235


S07- 98

Item Code

Q236

Q237Q238Q239Q240Q241Q242Q243

Q244Q245Q246Q247Q248Q249Q250

Q251

Q252

Q253

Q254

Q255

Q256

Q257

Q258

Q259

Q260


S07- 99

Item Code

Q261Q262Q263

Q264

Q265

Q266Q267

Q268

Q269Q270Q271Q272Q273Q274Q275

Q276Q277Q278Q279Q280Q281Q282Q283Q284Q285Q286Q287Q288Q289

Q290

Q291


S07- 100

Item Code

Q292

Q293

Q294

Q295Q296Q297

Q298

Q299

Q300

Q301

Q302

Q303

Q304

Q305

Q306


S07- 101

Item Code

Q307

Q308Q309Q310Q311Q312Q313

Q314Q315Q316Q317Q318

Q319

Q320

Q321

Q322

Q323

Q324

Q325


S07- 102

Item Code

Q326

Q327

Q328

Q329

Q330

Q331

Q332

Q333

Q334

Q335


S07- 103

Item Code

Q336Q337Q338Q339

Q340

Q341


S07- 104

Item Code

Q342

Q343

Q344

Q345Q346

Q347

Q348Q349Q350Q351Q352Q353Q354

Q355Q356Q357Q358Q359Q360Q361

Q362Q363Q364Q365

Q366Q367

Q368Q369Q370Q371


S07- 105

Item Code

Q372Q373Q374

Q375Q376Q377Q378Q379Q380Q381

Q382Q383Q384Q385Q386Q387Q388

Q389Q390Q391Q392Q393Q394Q395

Q396Q397Q398Q399Q400Q401Q402Q403

Q404

Q405

Q406

Q407


S07- 106

Item Code

Q408

Q409


S07- 107

Item Code

Q410Q411Q412Q413Q414Q415Q416

Q417Q418Q419Q420Q421Q422Q423Q424Q425Q426Q427Q428Q429Q430

Q431

Q432

Q433

Q434

Q435

Q436

Q437

Q438

Q439

Q440


S07- 108

Item Code

Q441

Q442

Q443

Q444

Q445

Q446

Q447

Q448

Q449Q450Q451Q452Q453

Q454

Q455

Q456

Q457Q458

Q459

Q460

Q461

Q462


S07- 109

Item Code

Q463

Q464

Q465

Q466

Q467

Q468

Q469Q470

Q471

Q472

Q473

Q474

Q475

Q476


S07- 110

Item Code

Q477

Q478


S07- 111

Item Code

R001R002R003

R004

R005

R006

R007

R008

R009

R010

R011

R012

R013


S07- 112

Item Code

R014


S07- 113

Item Code

R015

R016

R017

R018

R019

R020R021

R022

R023R024

R025R026

R027R028

R029

R030

R031

R032

R033


S07- 114

Item Code

R034

R035

R036

R037

R038

R039

R040

R041

R042

R043R044

R045

R046

R047

R048

R049

R050

R051

R052

R053

R054

R055


S07- 115

Item Code

R056

R057

R058

R059

R060

R061

R062

R063

R064

R065

R066

R067

R068

R069


S07- 116

Item Code

R070


S07- 117

Item Code

S001

S002

S003S004S005

S006

S007

S008S009

S010

S011

S012

S013

S014

S015

S016

S017


S07- 118

Item Code

S018

S019

S020

S021

S022

S023

S024

S025S026

S027

S028

S029

S030

S031

S032

S033


S07- 119

Item Code

S034


S07- 120

Item Code

S035

S036

S037

S038

S039S040S041S042S043S044S045

S046S047S048S049S050S051

S052S053S054S055S056S057

S058

S059

S060

S061

S062


S07- 121

Item Code

S063

S064

S065

S066

S067

S068

S069S070

S071

S072S073S074S075S076

S077

S078

S079


S07- 122

Item Code


S07- 123

Item Code

T001T002T003T004T005T006

T007T008T009

T010T011T012T013T014T015

T016T017T018

T019

T020

T021


S07- 124

Item Code

T022

T023

T024

T025

T026

T027

T028

T029

T030

T031

T032

T033

T034

T035

T036

T037

T038

T039

T040

T041

T042


S07- 125

Item Code

T043


S07- 126

Item Code

T044T045T046T047T048T049T050T051T052T053T054T055T056T057

T058T059T060T061T062T063T064T065T066

T067T068T069T070T071T072T073

T074T075T076T077T078


S07- 127

Item Code

T079T080T081T082T083T084T085T086T087

T088

T089

T090T091

T092

T093

T094

T095

T096

T097T098

T099

T100

T101

T102

T103

T104


S07- 128

Item Code

T105

T106

T107

T108

T109T110T111

T112T113T114T115T116T117T118T119T120T121

T122

T123

T124

T125

T126

T127

T128T129


S07- 129

Item Code

T130T131

T132T133T134T135T136T137

T138T139T140T141T142T143T144T145T146

T147T148T149T150T151T152T153T154

T155T156T157T158

T159T160


S07- 130

Item Code

U001

U002

U003

U004

U005

U006

U007

U008


S07- 131

Item Code

U009


S07- 132

Item Code

U010

U011

U012

U013

U014

U015

U016

U017U018U019U020U021

U022U023U024U025


S07- 133

Item Code

U026


S07- 134

Item Code

U027U028U029U030U031

U032U033U034U035U036

U037U038U039U040U041

U042U043U044U045


S07- 135

Item Code

U046


S07- 136

Item Code

U047U048U049U050U051

U052U053U054U055U056

U057U058U059U060U061


S07- 137

Item Code

U062U063U064U065U066

U067U068U069U070U071


S07- 138

Item Code

U072U073U074U075U076

U077U078U079U080U081


S07- 139

Item Code

U082U083U084U085U086

U087U088U089U090U091


S07- 140

Item Code

U092U093U094U095U096

U097U098U099U100U101

U102U103U104U105U106


S07- 141

Item Code

U107U108U109U110U111

U112U113U114U115U116

U117U118


S07- 142

Item Code

U119U120


S07- 143

Item Code

U121

U122U123U124U125U126

U127U128U129U130U131

U132U133U134U135U136


S07- 144

Item Code

U137U138U139U140U141

U142U143U144U145U146


S07- 145

Item Code


S07- 146

Item Code

U147U148U149U150U151

U152U153U154U155U156

U157U158U159U160U161

U162U163U164U165U166


S07- 147

Item Code

U167U168U169U170U171

U172U173U174U175U176

U177U178U179U180U181


S07- 148

Item Code

U182U183U184U185U186

U187U188U189U190U191

U192U193U194U195U196


S07- 149

Item Code

U197U198U199U200U201


S07- 150

Item Code

U202U203U204U205U206

U207U208U209U210U211

U212U213U214U215U216


S07- 151

Item Code

U217U218U219U220U221

U222U223U224U225U226

U227U228U229U230U231


S07- 152

Item Code

U232U233U234U235U236

U237U238U239U240U241

U242U243U244U245U246


S07- 153

Item Code

U247U248U249U250U251


S07- 154

Item Code

U252U253U254U255U256

U257U258U259U260U261

U262U263U264U265U266


S07- 155

Item Code

U267U268U269U270U271

U272U273U274U275U276

U277U278U279U280U281


S07- 156

Item Code

U282U283U284U285U286

U287U288U289U290U291

U292U293U294U295U296


S07- 157

Item Code

U297U298U299U300U301

U302U303U304U305U306

U307U308U309U310U311


S07- 158

Item Code

U312U313U314U315U316

U317U318U319U320U321

U322U323U324U325U326

U327U328U329U330U331

U332U333U334U335U336

U337


S07- 159

Item Code

U338U339U340U341

U342U343U344U345U346

U347U348U349U350U351

U352U353U354U355U356

U357U358U359U360U361

U362U363U364U365U366

U367U368U369U370U371


S07- 160

Item Code

U372U373U374U375U376

U377U378U379U380U381

U382U383U384U385U386

U387U388U389U390U391

U392U393U394U395U396

U397U398U399


S07- 161

Item Code

U400U401

U402U403U404U405U406

U407U408U409U410U411

U412U413U414U415U416

U417U418U419U420U421

U422U423U424U425U426

U427U428U429U430U431


S07- 162

Item Code

U432U433U434U435U436

U437U438U439U440U441

U442U443U444U445U446

U447U448U449U450U451

U452U453U454U455U456

U457U458U459U460U461

U462U463U464U465


S07- 163

Item Code

U466

U467U468U469U470U471

U472U473U474U475U476

U477U478U479U480U481

U482U483U484U485U486

U487U488U489U490U491

U492U493


S07- 164

Item Code

U494U495U496

U497U498U499U500U501

U502U503U504U505U506

U507U508U509U510U511

U512U513U514U515U516

U517U518U519U520U521

U522U523U524U525U526


S07- 165

Item Code

U527U528U529U530U531

U532U533U534U535U536

U537U538U539U540U541

U542U543U544U545U546

U547U548U549U550U551

U552U553U554


S07- 166

Item Code

U555U556

U557U558U559U560U561

U562U563U564U565U566

U567U568U569U570U571

U572U573U574U575U576

U577U578U579U580U581

U582U583U584U585U586


S07- 167

Item Code

U587U588U589U590U591

U592U593U594U595U596

U597U598U599U600U601

U602U603U604U605U606

U607U608U609U610U611

U612U613U614U615U616

U617U618U619U620


S07- 168

Item Code

U621

U622U623U624U625U626

U627U628U629U630U631


S07- 169

Item Code

U632U633U634U635U636

U637U638U639U640U641

U642U643U644U645U646

U647U648U649U650U651


S07- 170

Item Code

U652U653U654U655U656

U657U658U659U660U661

U662U663U664U665U666


S07- 171

Item Code

U667U668U669U670U671

U672U673U674U675U676

U677U678U679U680U681


S07- 172

Item Code

U682U683U684U685U686

U687U688U689U690U691

U692U693U694U695U696


S07- 173

Item Code

U697U698U699U700U701

U702U703U704U705U706

U707U708U709U710U711


S07- 174

Item Code

U712U713U714U715U716

U717U718U719U720U721

U722U723U724


S07- 175

Item Code

U725U726

U727U728U729U730U731

U732U733U734U735U736

U737U738U739


S07- 176

Item Code

U740U741


S07- 177

Item Code

U742

U743

U744

U745

U746

U747

U748

U749

U750

U751

U752

U753


S07- 178

Item Code

U754

U755


S07- 179

Item Code

U756

U757

U758

U759

U760

U761

U762

U763

U764

U765

U766

U767


S07- 180

Item Code

U768

U769

U770

U771

U772

U773


S07- 181

Item Code

U774

U775

U776

U777

U778

U779


S07- 182

Item Code

U780

U781

U782U783U784U785U786

U787U788U789U790U791

U792


S07- 183

Item Code

U793U794U795U796


S07- 184

Maintenance BSR for 2014Department of Buildings, Sethsiripaya, Battaramulla.

Imperial Units

Description

A-DEMOLISHER

Demolishing brickwork in cement stacking brick and clearing debris away Cube

Demolishing brickwork in lime stacking brick and clearing debris away CubeDemolishing cabook masonry in lime mortar stacking cabook and clearing debris away

Cube

Dismantling cadjan roofing or walling stacking timber and clearing debris Sqr

Removing existing Ceiling, stacking materials and clearing debris SqrDemolishing Cement concrete , and clearing debris in 6" floors Cube

Sqr

Sqr

Sqr

SqrRemoving and stacking Door or Window, size up to 40 Sq.ft: from existing walls

NosRemoving and stacking Door or Window, size over 40 sq.ft from existing walls

NosRemoving and stacking Door or Window, sash only up to 40 Sq.ft: from existing walls

NosRemoving and stacking Door or Window, sash only over 40 sq.ft: from existing walls

NosRemoving and stacking Down pipes, 4" to 6" dia: G.I. old or decayed, from existing building

L.ftDemolishing drains and clearing debris L.ftRemoving and stacking Expanded Metal from existing frames sq.ft

L.ftDemolishing floors brick paved, and clearing debris away Sqr

NosRemoving and stacking Glass panes in doors and windows and fanlights sq.ft

Removing and stacking Gutter, eaves, from roofs of single storeyed buildings L.ft

Removing and stacking gutter, eaves, from roofs of 2 storeyed buildings L.ft

Item Unit

Demolishing reinforced cement concrete in suspended floors of 4" thick, removing reinforcement and clearing debris

Removing and stacking corrugated sheets, iron, asbestos or Aluminium alloy from roof , or walls

Removing and stacking corrugated sheets, iron asbestos or Aluminium alloy from roofs or walls of two storied buildings

Removing and stacking Corrugated sheets, iron, asbestos or Aluminium alloy from roofs or walls of three storeyed buildings

Uprooting fence , rolling up and stacking barbed wire and all other materials . (Length of fencing to be measured)

Removing and stacking gate sash after demolishing cement concrete blocks or removing posts and separating pintols (Demolishing brickwork where necessary paid for separately).



S07- 185

Description Item Unit

Removing and stacking gutter, eaves, from roofs of three storeyed buildings L.ft

Removing and stacking partitions at site including making good to walls and floorssq.ft

Chipping lime plastering Chipping lime plastering and clearing debris away SqrChipping rendering, cement, and clearing debris away from brick walls and floors

SqrChipping rendering, cement, and clearing debris away from cement concrete floors and walls

SqrRoof removing

Sqr

Sqr

SqrDemolishing rubbleDemolishing rubble masonry in cement, stacking rubble and clearing debris

CubeDemolishing rubble masonry in lime, stacking rubble and clearing debris CubeDemolishing tiles, glazed and clearing debris SqrRemoving and stacking tilesRemoving and stacking tiles Calicut or half round, from roof of single storeyed buildings

SqrRemoving and stacking tiles Calicut or half round, from roof of 2 storeyed buildings

SqrRemoving and stacking tiles Calicut or half round, from roofs of three storeyed buildings

SqrRemoving water proof, asbestos ceiling &Valance or Barge boards.

Removing waterproof Treatment or hot bitumen from flat roof and clearing debris awaySqr

Sqr

Sqr

L.ft

L.ftChipping cement plasterChipping cement plaster, soffit and clearing debris away SqrTransporting debrisTransporting debris cleared away from site by tractor (app10 miles away )

Load

Roof removing tiles and timber, stacking serviceable materials and clearing debris in single storeyed buildings

Roof removing tiles and timber, stacking serviceable materials and clearing debris in two storeyed buildings

Roof removing tiles and timber, stacking serviceable materials and clearing debris in three storeyed buildings

Removing ceiling asbestos including timber framework, stacking serviceable materials and clearing debris away in single storeyed buildings

Removing ceiling asbestos including timber framework, stacking serviceable materials and clearing debris away in two storeyed buildings

Removing and stacking Valance, Barge board materials and clearing debris away in single storeyed building

Removing and stacking Valance, Barge board materials and clearing debris away in two storeyed building


S07- 186


LoadTransporting debris cleared away from site by 3.5 cube capacity heavy vehicle and loading with JCB machine ( app. 10 miles away )


S07- 187


Preparatory work

SqrFelling Trees

Nos

Nos

Nos

NosRemoving Top SoilRemoving top soil to a depth not exceeding 6" & depositing as directed within site

Sqr

Clearing site vegetation including removal of bushes, shrub under growth hedges and tree stumps up to 12" girth measured at height up to 3' 0" above ground level ,removing rubbish up to a distance of 150 ft beyond the outer walls of the proposed building.

Removing trees and stumps size of girth varies from 1' 0" and up to 2' 0" and girths are measured at 3' 0" height above ground level including cutting of trunks and branches, grubbing up roots, staking of serviceable materials and disposal of unserviceable materials.( aveg. 6" dia. and aveg. ht 10')

Removing trees and stumps size of girth varies beyond 2' 0"" and up to 4' 0" and girths are measured at 3' 0" height above ground level including cutting of trunks and branches, grubbing up roots, staking of serviceable materials and disposal of unserviceable materials. ( aveg. 12" dia. and aveg. ht 16' 6")

Removing trees and stumps size of girth varies beyond 4' 0" and up to 8' 0 " and girths are measured at 3' 0" height above ground level including cutting of trunks and branches, grubbing up roots, staking of serviceable materials and disposal of unserviceable materials. ( aveg. 2' 0"dia. and aveg. ht 23' 0")

Removing trees and stumps size of girth varies beyond 8' 0 " and girths are measured at 3' 0" height above ground level including cutting of trunks and branches, grubbing up roots, staking of serviceable materials and disposal of unserviceable materials. ( aveg. 3' 4" dia. and aveg. ht 33' 0")


S07- 188


B-EXCAVATOR

Cube

Cube

Cube

Cube

Cube

Cube

CubeBenching rock in foundation in 3"-6" steps.(Blasting not allowed) sq.ft

- Deleted -Backfilling & compacting pits and trenches with available earth . CubeBackfilling & compacting pits and trenches with imported earth. Cube

Sqr

Cube

Cube

Cube

Filling Under floors & foundations

Cube

Cube

Excavation over site to reduce level in any material except rock requiring blasting including depositing and leveling as directed up to a distance not exceeding 30ft

Excavation in trenches for walls/column pits in soft/loose soil from, 0 to 5ft deep and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).

Excavation in trenches for walls/column pits in ordinary soil from, 0 to 5ft deep and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).

Excavation in trenches for walls/column pits in hard dense soil from 0 to 5ft deep and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).

Excavation in trenches for walls/column pits in mud/wet soil from 0 to 5ft deep and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).

Excavation in trenches for walls/column pits in soft disintegrated rock (not requiring blasting) up to a depth of 5ft and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).

Excavation in trenches for walls/column pits in hard rock requiring blasting up to a depth of 5ft and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).

Cutting turf sods loading to hand carts and transporting up to 30 yards laying and watering for 30 days .(Royalty for turf pegging and transport beyond 30 yards paid separately)

Drains, earth, in any soil except rock requiring blasting cut to gradient and shape as directed and depositing soil within site

Excavation for foundation in any material except rock requiring blasting, part return fill in and ram, and disposing surplus within site as directed.(not exceeding 5ft depth)

Excavation & leveling site in any material except rock requiring blasting, including depositing and leveling.

Note:-For excavation beyond the depth of 5' 0" an additional unskilled laborer should be added for every additional depth of 5' 0" or part thereof for each cube of excavation beyond the original 5' 0" depth.

Filling under floors with gravel or other approved quality of filling, spread, water and well rammed in 3" layers with available earth

Filling under floors with gravel or other approved quality of filling, spread, watered and well rammed in 3" layers with imported earth.


S07- 189


Sand filling in Column footing, under wall foundations, watered and well rammed.Cube

Earth work supports

sq.ftEarthwork support (close planking) in trenches up to 5ft 0" depth (2" thick class 2 Timber )

sq.ft

sq.ft

Earthwork support (open planking) in trenches up to a depth of 5ft 0" (2" thick class 2 Timber )

Earthwork support (Close planking ) in deep excavation in trenches up to 15ft 0" depth. Consider trench of 15ft 0" width 5ft 0" at top and 3ft 6" at bottom. (2" thick class 2 Timber )(area supported 2/15ft x 15ft) 450 sq.ft


S07- 190


C-CONCRETERConcreting Mass (Gr.15 Mix)

Cube

Cube

Cube

Cube

Cube

CubeConcreting Drains (Gr.15 Mix)

L.ft

L.ftConcrete (Grade 20 Mix)

Cube

Cube

L.ft

L.ft

NosCurbs

L.ftConcreting Drains, semi-circular

L.ftConcreting Lintols (Gr. 20 Mix)

L.ft

Mixing and Placing of cement concrete 1:3:6 with 1" metal, hand mixing up to 1 cube, in ground floor. (Shuttering paid for separately)

Mixing and Placing of cement concrete 1:3:6 (1½") using mixer, above one cube, in ground floor. (Shuttering paid for separately)

Mixing and Placing of concrete 1:3:6 with 2" metal, using mixer, above one cube, in ground floor. (Shuttering paid for separately)

Mixing and Placing of cement concrete 1:3:6 (2"), hand mixing up to one cube, in ground floor.(Shuttering paid for separately)

Mixing and Placing of cement concrete 1:2 ½:5 (1") using mixer, above one cube, in ground floor.(Shuttering paid for separately)

Mixing and Placing of cement concrete 1:2 ½:5 (1"), hand mixing up to one cube, in ground floor. (Shuttering paid for separately)

Drains semi-circular in cement concrete 1:3:6(1"), 9" wide and 9" average depth, 3" thick sides and base, inclusive of 1/2" cement rendering 1:3 with necessary expansion joints and excavation(shuttering paid separately), but without ramp.

Drains semi-circular in cement concrete 1:3:6(1") 9" wide and 9" average depth, 3" thick sides and base, inclusive of 1/2" cement rendering 1:3 with necessary expansion joints and excavation(shuttering paid separately),but with 1ft 6" wide ramp .

Cement concrete 1:2:4(3/4") using mixer, above one cube. (R/F and Shuttering paid for separately)

Cement concrete 1:2:4(3/4")using mixer, up to one cube. (R/F and Shuttering paid for separately)

Channels 2" semi-circular, forming in cement concrete floors and 1/2" cement rendering 1:2 (Extra over concrete floors)

Channels 4" semi-circular, forming in cement concrete floors and 1/2" cement rendering 1:2 (Extra over concrete floors)

Supplying & laying corbel stone in cement concrete1:2:4(3/4") reinforced with 4 Nos: 3/8" rods ( shuttering paid separately)

Supplying and laying curb in cement concrete 1:2:4 (3/4") 9" high 3" wide and cement rendered 1/2" thick 1:2.(shuttering excavation paid separately)

Supplying and laying Drains, semi-circular, in cement concrete 1:3:6(1") 9" wide and 9" average depth, with 3" thick sides and base inclusive of 1/2" cement rendering 1:3 expansion joints as necessary, including necessary excavation (Shuttering paid separately)

Lintol, cement concrete 1:2:4(3/4") 4 1/2" x 6" (Reinforcement paid for separately). Rate inclusive of shuttering


S07- 191


L.ft

L.ft

L.ft

L.ft

L.ft

L.ftNos

Slabs over drains

sq.ft

Nos

NosSquatting plate for latrines , cement concrete 1:2:4( 3/4'') as per type plan.

NosConcreting of Beams and Columns (Gr. 20 Conc)

Cube

Cube

Cube

Cube

Cube

CubeConcreting Slabs (Gr. 20 Mix)

Sqr

SqrConcreting Structural Elements (Gr. 25 Mix)Cement concrete 1:1½:3(3/4") in ground floor, using mixer and vibrator. Cube

Lintol, cement concrete 1:2:4(3/4") 9" x 6" (Reinforcement paid for separately). Rate inclusive of shuttering






Pad stones in cement concrete 1:2:4(3/4" Metal) precast or in situ.

Slabs over drains ,cement concrete 3" thick 1:2 :4 (3/4) and 1/2" cement rendering 1:2 .(Reinforcement paid for separately ) Rate inclusive of shuttering

Spur stones 8" x 8" x 6" in cement concrete 1:2:4(3/4") for veranda posts supplying and fixing(shuttering paid for separately)

Spur stones 4" x 3" x 2" in cement concrete 1:2:4(3/4") for door posts supplying and fixing(shuttering paid for separately)

Cement concrete 1:2:4(3/4") in column shafts in ground floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)

Cement concrete 1:2:4(3/4") in column shafts in first floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately).

Cement concrete 1:2:4(3/4") in column shafts in second floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately).

Cement concrete 1:2:4(3/4") in beams in ground floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)

Cement concrete 1:2:4(3/4") in beams in first floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)

Cement concrete 1:2:4(3/4") in beams in second floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)

4" thick R.C.C 1:2:4(3/4") in 1st: floor slab using mixer and vibrator. (Reinforcement and shuttering paid for separately)

5" thick R.C.C. in 1st: floor slab using mixer and vibrator. (Reinforcement and shuttering paid for separately)


S07- 192


Cube

Cube

Cube

Cube

Cube

CubeReady mixed Concrete

- Deleted - - Deleted - - Deleted -

Form work (Untreated Non-structural Category A)

Sqr

sq.ft

sq.ftForm work (Using Timber planks)

sq.ft

sq.ftPlywood form work (20mm tk.)

sq.ft

sq.ft

Cement concrete 1:1½:3(3/4") in column shafts in ground floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)

Cement concrete 1:1½:3(3/4") in column shafts in first floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately).

Cement concrete 1:1½:3(3/4") in column shafts in second floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately).

Cement concrete 1:1½:3(3/4") in beams in ground floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)

Cement concrete 1:1½:3(3/4") in beams in first floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)

Cement concrete 1:1½:3(3/4") in beams in second floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)

Shuttering for floor slab concrete including 4" x 2" (untreated non-structural category A) timber joists and necessary props. up to 12ft height. (Rate to include for dismantling same when required).

Shuttering for column shaft 9" x 9" including (untreated non-structural category A) timber joists and necessary props etc. (Rate to include for dismantling same when required)

Shuttering for beam sides & soffit in (untreated non-structural category B) timber, joists and necessary props etc. (Rate to include for dismantling same when required)

Form work with (untreated non-structural category B) timber planks for column shafts 9" x 9" including (untreated non-structural category B) timber joists and necessary props etc. Rate to include for dismantling same when required.

Form work with (untreated non-structural category B) timber planks for beam sides soffits including (untreated non-structural category B) timber props etc. (Rate to include for dismantling same when required).

Supplying and fixing of 3/4" or (20mm) thick plywood form work for concrete beams in ground floor, including (untreated non-structural category B) timber planks , Battens & Joists for beam sides, soffits etc. (Rate to include for dismantling the same when required). consider 9"x12" beam to 20ft, long contact area 55sft.

Supplying and fixing 3/4" or (20mm) thick plywood form work in column in ground floor, including (untreated non-structural category B) timber joists and necessary props etc. Rate to include for dismantling same when required. Consider area 15 sq.ft. ( 5ft high 9"x9" col. )


S07- 193


sq.ft

Supplying and fixing 3/4" or (20mm) thick plywood timber formwork for underside of fist floor slab, including 4" x 2" (untreated non-structural category B) timber joists and necessary props. up to 12ft height. (Rate to include for dismantling same when required). consider 20 x 10 area - 200sft.


S07- 194


D-BRICKLAYERArch, Segmental, Brick in cement 1:3 including centering. CubeBrickwork in (1:5) cement mortar Brickwork in cement mortar (1:5) above 1 cube, in ground floor. CubeBrickwork in cement mortar (1:5) up to 1 cube, in ground floor. (up to first floor level).

Cube

CubeBrickwork 4 1/2" thick in cement mortar 1:5 above 1 square. SqrBrickwork 4 1/2" thick in cement mortar 1:5 up to 1 square. Sqr

Sqr9" thick brick wall cement sand 1:5 in ground floor SqrBrick work 13½ thick in cement sand 1:5 in superstructure in ground floor

SqrBrickwork Wire cut)4½ thick brick wall (wire cut) in cement sand 1:5 in ground floor Sqr9" thick in cement and sand 1:5 with wire cut brick Sqr13½ thick brick wall (wire cut) in cement sand 1:5 in ground floor SqrExtra over for brickwork ,from first floor level to second floor. ( for Item Nos. D002 to D005)

Cube

Cube

SqrExtra over 4 1/2" brickwork , ,above second floor level. ( for Item Nos. D006 to D008)

Sqr

L.ft

L.ft

L.ft

L.ftCornices, brick in cement 1:5 and, cement rendering 1:3 up to 9" projection and 9" depth.

L.ft

sq.ft

L.ft

L.ft

Brickwork in cement mortar 1:5 with bricks available at site including sorting and cleaning bricks.

Brickwork 4 1/2" thick in cement mortar 1:5 with available bricks including sorting and cleaning.

Extra over for brickwork ,from second floor level to third floor. ( for Item Nos. D002 to D005)

Extra over 4 1/2" brickwork ,from first floor level to second floor. ( for Item Nos. D006 to D008)

Coping, brick in cement 1:5, weathering and throating on 4 1/2" walls, cement rendering 1/2" 1:3 complete.

Coping, brick in cement 1:5, weathering and throating on 9" walls, and 1/2" cement rendering 1:3 complete.

Coping, brick in cement 1:5, weathering and throating on 14" walls, cement rendering 1/2" 1:3 complete.

Coping, brick in cement 1:5, weathering and throating on 9" walls, and 1/2" cement rendering 1:3 with available brick.

Door or Window inserting in existing walls including makings, openings and making good to floors and walls (Lintol or Arch, and door or window paid for separately).

Drains, brick in cement (1:5) 9" to 12" average depth, 12" wide and cement rendering 1/2" thick 1:2 finished smooth complete with expansion joints as necessary including excavation. (Apron paid for separately).

Drains, brick in cement 1:5, 6"-9" average depth and 9" wide, cement rendering 1/2", 1:2 finished smooth complete with expansion joints as necessary including excavation (apron paid for separately).


S07- 195


L.ft

L.ftVent opening up to 12" height and 6" width forming on existing walls and walls made good.

NosBrickwork in (1:8) cement mortar Brickwork in cement and sand 1:8 in foundation up to D.P.C. CubeBrickwork in cement and sand 1:8 in superstructure in ground floor. CubeBrickwork in cement and sand 1:8 in 1st: floor. CubeBrickwork in cement and sand 1:8 in 2nd: floor. Cube

Drains, scott's pattern, including apron formed of brick masonry in cement mortar 1:5 and 1/2" cement rendered, finished smooth complete with expansion joints as necessary including excavation (apron paid for separately)

Steps, 12" wide and 6" to 9" high masonry or brickwork in cement mortar 1:3, rendering 1/2" cement 1:2 with foundation 6" below ground.


S07- 196


E-MASONRandom RubbleRandom Rubble Masonry in cement Mortar 1:5, above 1 cube. CubeRandom Rubble Masonry in cement Mortar 1:5, up to 1 cube. Cube

CubeCellular (Hollow) block masonry

Sqr

Sqr

SqrSolid block masonry

Sqr

Sqr

SqrPaste rubble masonrySupplying & Laying pointed or Paste rubble masonry in cement and sand 1:2 in ground Floor.

Sqr

Random Rubble Masonry in cement mortar 1:5 with available rubble including sorting out and cleaning rubble.

4" thick Cellular (Hollow) block masonry in cement and sand mortar 1:5 in ground floor cavities unfilled. ( size of each block 16"x8"x4") (Min com/st 3.0 N/mm2 )

6" thick Cellular (Hollow) block masonry in cement and sand mortar 1:5 in ground floor, cavities unfilled. ( size of each block 16"x8"x6") (Min com/st 3.0 N/mm2 )

8" thick Cellular (Hollow) block masonry in cement and sand mortar 1:5 in ground floor Cavities unfilled. ( size of each block 16"x8"x8") (Min com/st 3.0 N/mm2 )10'x10' area

4" thick solid block masonry in cement and sand mortar 1:5 in ground floor. ( size of each block 16"x8"x4") 10'x10' area (Min com/st 3.0 N/mm2 )

6" thick solid block masonry in cement and sand mortar 1:5 in ground floor.10'x10' area (size of each block 16"x8"x6") (Min com/st 3.0 N/mm2 )

8" thick solid block masonry in cement and sand mortar 1:5 in ground floor. 10'x10' area ( size of each block 16"x8"x8") (Min com/st 3.0 N/mm2 )


S07- 197


F-PAVIORExpansion joints in brick floors, filling with bitumen and sand. L.ft

L.ft

Sqr

Sqr

Sqr

SqrFloors, gravel Floors, gravel 4" thick, spreading, watering and ramming. SqrFloor tiles (Laying only)

--Do-- for, tiles 8" x 8" in size. sq.ft--Do-- for, tiles 12" x 12" in size. sq.ft--Do-- for, tiles 16" x 16" in size. sq.ft--Do-- for, tiles 24" x 24" in size sq.ftTiles- pressedTiles, pressed of approved pattern and colour, supplying and fixing. sq.ft

sq.ftsq.ft

sq.ftsq.ftsq.ft

Floor tiles- Porcelain glazed (Non homogeneous)

Expansion joints in concrete floors filling with bitumen and sand (to full depth of concrete and rendering).¼" tk and 4" deep.

Floors, brick paving, 3" thick, set in lime mortar 2:5 and cement rendering 1/2"thick, 1:2 mixture.

Floors, brick paving 3" thick, set in lime mortar 2:5 and cement rendering 1/2" thick, 1:3 with available bricks, including sorting out and cleaning bricks.

Floors, cement concrete 1:2½:5(1" metal) 3" thick cement rendering 1/2", 1:3 with expansion joints filling with cement and sand.

Floors, upper, cement concrete 1:2:4(3/4") 4" thick, cement rendering 1/2", 1:3 with lime putty rendering to soffit and expansion joints filling with cement and sand (Reinforcement paid for separately).

Fixing tiles on floors with all specials, including raking plaster and bedding in cement mortar 1:3 pointed with tile grout to match the tiles. (Tiles supplied by the client or paid separately.**)

Floor tiles- Ceramic Non-skid ( Approved quality) Ceramic ,Non-skid pattern tiles with all specials supplying and fixing to floors including raking plaster and bedding in cement mortar 1:3 and pointed with tile grout to match the tiles. (Quality approved by the Engineer.)

--Do-- for, 8" x 8" in size.( Range of a Tile Price : Rs 50-60) --Do-- for, 12"x12" in size. ( Range of a Tile Price : Rs 135-160)Floor tiles- Ceramic glazed (Non homogenous)-Local Ceramic , glazed, Non homogenous floor tiles with all specials supplying and fixing to floors including raking plaster bedding with cement mortar 1:3 and pointed with tile grout to match the tiles. (Rocell or equivalent brand)

--Do-- for, 8" x 8" in size. ( Range of a Tile Price : Rs 71-83) --Do-- for, 12" x 12" in size. ( Range of a Tile Price : Rs 130-150) --Do-- for, 16" x 16" in size. (, Range of a Tile Price : Rs 240-288)

Porcelain, glazed, Non homogenous floor tiles with all specials supplying and fixing to floors including raking plaster and bedding in cement mortar 1:3. and pointed with tile grout to match the tiles. ( Rocell or equivalent brand)


S07- 198


sq.ftsq.ftsq.ftsq.ft

Floor tiles- Vitreous Porcelain ( Homogenous)-Local

sq.ftsq.ftsq.ft

Floor tiles- Polished Porcelain ( Homogenous)-Local

sq.ftsq.ftsq.ft

Floor tiles- Rustic Type ( Homogenous)-Local

sq.ftsq.ft

Floor tiles- (Approved quality)

sq.ft

sq.ft

sq.ft

sq.ft

sq.ftTerrazzo tile flooringTerrazzo tile flooring supplying and laying. Sqr

sq.ftTerracotta tiles

--Do-- for, 18" x 18" in size. ( Range of a Tile Price : Rs 370-398) --Do-- for, 24" x 24" in size.( Range of a Tile Price : Rs774-1375 ) --Do-- for, 24" x 12" in size. (Range of a Tile Price : Rs 387-497) --Do-- for, 24" x 16" in size. (Range of a Tile Price :Rs 547-674)

Porcelain ( glazed/Matt) Homogenous Vitreous, floor tiles with all specials supplying and fixing to floors including raking plaster and bedding in cement mortar 1:3 and pointed with tile grout to match the tiles. ( Rocell or equivalent brand)

--Do-- for, 8" x 8" in size. ( Range of a Tile Price : Rs 70-80) --Do-- for, 12" x12" in size. ( Range of a Tile Price : Rs 160-170) --Do-- for, 16" x16" in size. ( Range of a Tile Price : Rs 260-280)

Porcelain Polished Homogenous, floor tiles with all specials supplying and fixing to floors including raking plaster and bedding in cement mortar 1:3 and pointed with tile grout to match the tiles. ( Rocell or equivalent brand)

--Do-- for, 8" x 8" in size.( Range of a Tile Price : Rs 110--130) --Do-- for, 12" x 12" in size. ( Range of a Tile Price : Rs 290-300) --Do-- for, 24" x 24" in size. ( Tile Price : Rs 1465 )

Floor tiles- Rustic Type ( Homogenous), with all specials supplying and fixing to floors including raking plaster and bedding in cement mortar 1:3 and pointed with tile grout to match the tiles. ( Rocell or equivalent brand)

--Do-- for, 12" x 12" in size. ( Range of a Tile Price : Rs 160-170) --Do-- for,16" x 16" in size. ( Range of a Tile Price : Rs 293-343)

Vitreous ceramic floor tiles, supplying and laying on floor including raking plaster bedding with cement mortar 1:3 and pointed with tile grout to match the tiles. (Quality approved by the Engineer.)

--Do-- for, 12" x 12" in size. solid colour ( matt/ glazed ) Range of a Tile Price around : Rs 125

--Do-- for, 12" x 12" in size, rustic , decorative , heavy duty tiles ( colour ) Range of a Tile Price around : Rs 145

--Do-- for, 12" x 12" in size, step floor tiles 12"x12" Range of a Tile Price around : Rs 180

--Do-- for, 16"x16" in size, solid colour ( matt /glazed ) Range of a Tile Price around : Rs 275

--Do-- for, 24"x24" in size, solid colour ( heavy duty , matt or glazed ) Range of a Tile Price around : Rs 560

Terrazzo, wall lining with precast walling slabs 1 1/2" thick supplying and fixing to complete.


S07- 199


sq.ftTiles terracotta 8" x 8" of approved tiles , supply and fixed to floors including racking plaster bedding in cement mortar 1:3 .


S07- 200


Wall tiles -glazed ( Approved Quality)

--Do-- for, Coloured tiles 4" x 4" in size. sq.ft--Do-- for, white tiles 4" x 4" in size. sq.ft--Do-- for, Coloured tiles 6" x 6 in size. sq.ft--Do-- for, white tiles 6" x 6" in size. sq.ft

sq.ft--Do-- for, white tiles 8"x10" in size. sq.ft--Do-- for, colour tiles 8"x10" in size. sq.ft--Do-- for, white tiles 8"x12" in size. sq.ft--Do-- for, colour tiles 8"x12" in size. sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

Wall tiles (Fixing only)

--Do-- for size up to 8 "x16". sq.ft--Do-- for size up to 12 "x24". sq.ftBorder Tiles for Wall (Decorative)

L.ft

L.ft

Tiles, glazed with all specials, supplying and fixing to walls including raking plaster and backing in cement mortar 1:3.

--Do-- for available Tiles, (Tiles supplied by the client or paid separately.**)

Wall tiles -LocalTiles glazed with all specials , supplying and fixing to walls including raking plaster backing in cement mortar 1:3 and pointed with tile grout to match the tiles.(Lanka wall Tiles or equivalent brand)

--Do-- for Coloured, white or printed 4 1/2 "x4 1/2"(Range of a Tile Price : Rs 13--17)

--Do-- for Coloured, white or printed 8 "x8" (Range of a Tile Price : Rs 60--68)



--Do-- for Coloured, white or printed 12 "x16" (Range of a Tile Price : Rs 216-242)

--Do-- for Coloured, white or printed 12 "x24"( Range of a Tile Price : Rs 346-410)

Fixing tiles on walls with all specials , including raking plaster backing in cement mortar 1:3 and pointed with tile grout to match the tiles. (Tiles supplied by the client or paid separately.**)

Boarder tiles glazed colour 8"X3", with decorative patterns , supplying and fixing to walls including raking plaster backing in cement mortar 1:3 and pointed with tile grout to match the tiles.(Lanka wall Tiles or equivalent, Range of a Tile Price : Rs80-149)

Boarder tiles glazed colour 8"X3", with decorative patterns , supplying and fixing to walls including raking plaster backing in cement mortar 1:3 and pointed with tile grout to match the tiles.(Lanka wall Tiles or equivalent, Range of a Tile Price Rs150-218)


S07- 201


L.ft

L.ft

sq.ft

sq.ft

L.ftGlass block

sq.ftPVC carpeting Supplying and laying PVC carpeting with necessary adhesive etc. sq.ftVinyl Flooring

sq.ft

sq.ftLoop pile carpeting

sq.ftCut pile carpeting - Deleted -

sq.ftInterlocking paving

sq.ft



Granite flooring-LocalGranite floor tiles 12" x 12"x1/2" (Local) supplying and fixing to floors including raking plaster bedding with cement mortar 1:3. (Tile Price : Rs 750 )

Granite floor tiles 24" x 12"x3/4" (Local) supplying and fixing to floors including raking plaster bedding with cement mortar 1:3. (Tile Price : Rs 2700)

Labour cost for fixing 12" x 4"x1/2" Granite skirting to bottom line of walls including cutting ,rounding & Forming edges polishing etc.

Glass block 8" x 8" with all specials supplying and fixing to walls including raking plaster and bedding in cement mortar 1:3.

Supplying and laying 2mm thick Vinyl Flooring with necessary adhesive etc. (Mipolam 150 or equivalent)

Supplying and laying 2mm thick Vinyl Flooring with necessary adhesive etc. (Mactile - Gerflor or equivalent)

Supplying and laying Loop pile carpeting with 5mm thick with Mcfoam under layer , firmly bonded to the existing floor. Carpet having primary & Secondary backings, namely polypropylene & Classic back respectively. And having the minimum pile weight of 20 Oz-USA per sq.yard. & loop density of 6,100 Oz/Cu.yard. (Neyland II or equivalent)

Supplying and laying 1/8 gauged, Wide Open Cut pile carpeting (USA or equivalent) with 5mm thick with Mac Form under layer , firmly bonded to the existing floor. Carpet having primary & Secondary backings, namely woven polypropylene & Classic back polypropylene, respectively. And having the minimum pile weight of 30 Oz per sq.yard. & loop density of 5320 Oz/Cu.yard.

Supplying and Laying 80mm thick "Uni" type Coloured interlocking paving blocks having Compressive Strength of 40N/mm2, layed on plain improved sub surface. Rate inclusive for Quarry dust bedding


S07- 202


sq.ftPaving tile Slabs

sq.ft

sq.ft

Supplying and Laying 80mm thick "Uni" type Natural cement colour interlocking paving blocks having Compressive Strength of 40N/mm2, layed on plain improved sub surface. Rate inclusive for Quarry dust bedding.

Supplying and Laying 300 x300 x50mm thick Non Reinforced, Natural cement colour, Concrete paving Slab, layed on plain improved sub surface. Rate inclusive for Quarry dust bedding.

Supplying and Laying 300 x300 x50mm thick Reinforced, Natural cement colour, Concrete paving Slab, layed on plain improved sub surface. Rate inclusive for Quarry dust bedding.


S07- 203


G-ROOFERCorrugated sheets

SqrCorrugated Aluminium sheets

Sqr

Sqr

SqrCorrugated Asbestos Sheets

Sqr

Sqr

SqrCorrugated Asbestos "Colorup" Sheets

SqrZinc Aluminium Sheet Roofing

sq.ftCorrugated galvanized iron Sheet Roofing

Sqr

Sqr

SqrLeaks -on roofs

Corrugated sheets, iron, asbestos or Aluminium alloy fixed with hook bolts and nuts to roofing or walling, (Corrugated sheets available).

Corrugated Aluminium sheets 24 B.W.G roofing on (Group3,Category A) timber purlins supplied and fixed with Aluminium hooks and nuts or Aluminium drive screws including limpet washers etc.: complete with Aluminium ridging, including treating timber with wood preservative

Corrugated Aluminium sheet walling 24 B.W.G on 4" x 2" (Group3,Category A) timber framework, sheets to have 4" end lap and 1" corrugation side lap. (Wall plate measured separately).

Corrugated Aluminium sheets 24 B.W.G supplied and fixed to roof or wall (on existing framework) with hook bolts or drive screws etc.: Sheets to have 4" end lap and 1" corrugation side lap. (Wall plate measured separately).

Corrugated asbestos (Mascons or equivalent.) sheet roofing on (Group3,Category A) timber purlins supplied and fixed complete including treating timber with wood preservative (Ridging measured separately).

Corrugated asbestos (Mascons or equivalent.) sheet walling on 4"x2" (Group3,Category A) timber framework supplied and fixed complete.

Corrugated asbestos sheets supplied and fixed to roof or wall on existing framework with necessary coach screws and limpet washers or hook bolts.

Corrugated asbestos "Colorup" Sheets supplied and fixed to roof or wall on existing framework with necessary coach screws and limpet washers or hook bolts.

Supplying and fixing Zinc Aluminium roofing sheets (0.47 gauge)on existing frame work using nut & bolt / self tapping screws or fasteners. (Rhino Supermet or Equivalent.)

Corrugated galvanized iron Roofing 24 B.W.G on (Group3,Category A) timber purlins supplied and fixed complete with G.I ridging, washers, hook bolts or clips including treating timber with wood preservative. (Sheets to have 6" end laps and 1ft 1/2" corrugation side

Supplying and fixing 22 B.W.G Corrugated G.I walling on (Group3,Category A) timber framework

Corrugated G.I sheets 24 B.W.G supplied and fixed to roof, wall or fence with necessary cup washers and hook bolts and screws. (Timber framework paid for separately).


S07- 204


Leaks (up to 5 in number) in Tiled roofs of single storeyed buildings made good. Nos

Leaks (above 5 in number) in roofs of single storeyed buildings made good.Nos

Leaks (Up to 5 in number) in roofs of buildings above one story made good).Nos

Leaks (above 5 in number) in roofs of buildings above one story made good).Nos

Leaks in corrugated sheet roofs made good with bitumen washers and G.I bolts and nuts.Nos

NosRidging

L.ftRidging, Calicut pattern, bedded in cement and lime mortar 1:1:4, Coloured to match tiles.

L.ft

L.ft

L.ft

L.ft

L.ft

L.ft

L.ftZinc Aluminium ridge capping

L.ft

L.ftSkylight glass

NosTiles, Calicut pattern, flat

Nos

Leaks in corrugated sheet roofs patched with jute hesseain dipped in Asphalt and laid over with cement and sand layer above.

Ridging, asbestos cement, Aluminium alloy, or G.I available, fixed with hook bolts or screws.

Ridging, Calicut pattern bedded in cement and lime mortar 1:1:4, Coloured to match tiles, (Tiles available at site).

Ridging, Galvanized iron 24 B.W.G 18" wide overall supplied and fixed complete.

Ridging with asbestos cement close fitting ridges (Mascons or equivalent.) supplied and fixed complete with roofing screws or hook bolts.

Ridging, half round tiles, bedded in lime, cement mortar 1:1:4 and Coloured to match tiles.

Ridging with half round tiles bedded in lime cement mortar 1:1:4 and Coloured to match tiles (Tiles available at site).

Ridging, half round or Calicut pattern removed and re-laid in cement lime mortar 1:1:4 and Coloured to match tile.

Supplying and fixing Zinc Aluminium ridge capping (width 914mm ) 0.47 gauge, to existing sheet roof, using new fasteners or st /screws. (Rhino Supermet or Equivalent.)

Supplying and fixing Zinc Aluminium ridge capping(457mm girth) ( .47 gauge ) , to existing sheet roof, using new fasteners or st /screws. (Rhino Supermet or Equivalent.)

Skylight glass 2ft 0"x2ft 0", 1/4" thick ribbed, supplied & fixed to roof including necessary lime cement filleting.

Note: Refer Item numbers From H100 & H101 for Roofs with Calicut pattern tiles on (Group3, Category A) sawn timber framework

Tiles, Calicut pattern, flat, supplied and laid up to 5 tiles in single storeyed buildings.


S07- 205


NosTiles, Calicut pattern, flat, supplied and laid up to 5 Tiles in buildings of more than one story.

Nos

NosTiles Calicut pattern, supplied and laid in any building. SqrTiles Calicut pattern laid in any building (tiles available at site). SqrTiles Calicut pattern, ventilator, supplied and laid in single storeyed building.

NosTiles Calicut pattern, ventilator, supplied and laid in buildings of over one story.

Nos

NosNos

Tiles half round

Tiles half round supplied and laid, up to 50, in single storeyed buildings. NosTiles half round supplied and laid, above 50 and up to 100 in single storeyed buildings.

NosTiles, half round, supplied and laid up to 50 on buildings of more than one story.

Nos

NosTiles half round, supplied and laid in any building. SqrTiles, half round, laid in any building (Tiles available at site) SqrShifting and re-laying half round tiles. Sqr

SqrSupplying and laying half round tiles on the existing asbestos roof. SqrStructural Steel Purlins for Roof

--Do-- for (weight 6.7 Kg/m) & 76x38mm size "C" channel purlin L.ft--Do-- for (weight 10.42 Kg/m) & 102x51mm size "C" channel purlin L.ft--Do-- for (weight 14.9 Kg/m) & 127x64mm size "C" channel purlin, L.ft--Do-- for (weight 17.88Kg/m) & 152x76mm size "C" channel purlin, L.ftHigh tensile Galvanized steel, C-channel purlins for Roof

--Do-- with the sectional dimensions of "C" channel , 100mmx50mmx15mmL.ft

Tiles, Calicut pattern, flat, supplied and laid (above 5 and up to 25) in Single Storeyed buildings.

Tiles, Calicut pattern, flat, supplied and laid above 5 and up to 25 in buildings of more than one story.

Tiles, Fiber glass, laid in small quantities including fixing with G.I wire where necessary (tiles available at site)

Tiles, Fiber glass, Calicut pattern, supplied and fixed.

Note: Refer Item numbers From H102 & H103 for Roofs with Half round tiles on (Group3, Category A) sawn timber framework

Tiles, half round above 50 and up to 100 in number supplied and laid on roof of buildings of more than one story.

Shifting and re-laying Calicut pattern tiles.

Supplying & Fixing Structural & High Tensile Steel "C"" channel purlin, together with 75mmx75mmx6mm L-Iron cleats on roof truss with 10mm dia. Bolt and nuts. (Painting Paid for separately)

Supplying & Fixing High tensile Galvanized Steel "C" channel purlins, having the member thickness of 2.0mm (Tensile strength 450 N/mm2) standards complying with JISG 3302. Each Purlins connected with 75mmx75mmx6mm L-Iron cleats on roof truss together with 10mm dia. Bolt and nuts. (Painting is not considered)


S07- 206


--Do-- with the sectional dimensions of "C" channel , 150mmx65mmx20mm L.ft

Heat and Sound installation (Double side luminary Aluminium foil)

sq.ftTimber Members for Roofing Note:- Please find Timber Reepers from Item No H095 to H099

L.ftSupply and fixing 4''x2'' (Group3,Category A) timber rafters for roof work.

L.ftSupply and fixing 7''x2'' (Group3,Category A) timber ridge plate in roof work.

L.ftSupply and fixing 4''x3'' (Group3,Category A) timber wall plate in roof work.

L.ftSupply and fixing 5''x3'' (Group3,Category A) timber purlin in roof work.

L.ft

L.ft

1/2" thick heat and sound installation sheet laying on 3"x3" GI mesh existing steel purlin and fixing with binding

Supply and fixing 2''x2'' (Group3,Category A) timber Battons in roof work, with nails over 100' 0"

Supply and fixing 4''x3'' (Group3,Category A) timber Struts, up to 6' height in roof structure, including forming necessary Timber joints at both ends. 2' Timber bearer provided at Bottom.


S07- 207


H-CARPENTER & JOINER

L.ft

L.ft

L.ft

L.ft

L.ft

L.ftBoards, barge, valance, fascia

L.ft

L.ft

L.ft

L.ftBoards, barge, valance, fascia, available, fixing including cutting and minor repairs.

sq.ftCeiling / Partition

Sqr

Sqr

Sqr

Sqr

Beading, Burma Teak, 1 1/2" to 2" x1/2" plain chamfering, supplying and fixing complete with brass screws.

Beading, Burma Teak, 1"x 3/4" plain chamfering, supplying and fixing complete with brass screws.

Beading, Alstonia or local timber 1 1/2" to 2"x1/2" plain chamfering, supplying and fixing complete with brass screws.

Beading, Halmilla, 1 1/2" to 2" x 1/2", plain chamfering, supplying and fixing complete with brass screws.

Beading or filleting in Ginisapu or local timber for glass panes supplying and fixing complete with brass springs or brass panel pins.

Beading or filleting on underside of ceiling removing and re-fixing with brass screws complete.

Boards, barge, valance, fascia, 9" wide & 1" thick, in (Group 5,Category A), local timber fixing complete with necessary screws new or renewing.(above one Cubic foot)

Boards, barge, valance, fascia, 9" wide & 1" thick, in (Group 5,Category A),local timber supplying and fixing complete with necessary screws new or renewing, up to 1 Cu.ft.

Boards, barge, valance, fascia, 9" wide & 1" thick, in (Group 5,Category B), local timber fixing complete with necessary screws new or renewing.(above one Cubic foot)

Boards, barge, valance, fascia, 9" wide & 1" thick, in (Group 5,Category B),local timber supplying and fixing complete with necessary screws new or renewing, up to 1 Cu.ft.

Ceiling, asbestos (Mascons or equivalent.), flat fixing with clout headed nails to 4" x 2" joists and 2"x2" bearers of (Group 4,Category A) timber, including 1 1/2" x 1/2" cover fillets and 2 1/2" x 1 1/2" coves of Alstonia or equivalent timber. Rate to include 2 coats of wood preservatives to joists and bearers. Primer undercoating and two coats of emulsion paint to Asbestos sheets.

Flat asbestos (Mascons or equivalent.) horizontal eaves ceiling comprising 2" x 2" bearars in (Group 4,Category A) timber, asbestos sheet supplied and fixed with beadings & cove moulding, rate to include for applying wood preservative to timber frame, two coats enamel paint for beadings, and two coats of emulsion paint to ceiling.

Ceiling, asbestos, plywood, available, cut and fixing on existing bearers, rafters or frames (beading or cover fillets paid for separately)

Ceiling or partition, asbestos supplying and fixing with clout headed nails to existing bearers, rafters or frames (Beadings or cove fillets paid for separately)


S07- 208


L.ftCeiling, Lunumedella, available at site, fixing with new wire nails. Sqr

Sqr

Sqr

Sqr

Sqr

NosCeiling, upper side cleaning and debris clearing away. Sqr

Sqr

SqrPartitions

sq.ft

sq.ft

sq.ft

sq.ft

Ceiling board, 6" x 5/8" to 3/4", lunumedella, renewing in small quantities rate to include for scaffolding (up to 30 L.ft.)

Ceiling or partition, Lunumedella, 1/2" planed, lapped and nailed to existing frames or underside of rafters, above 1 square (Fillets and beadings paid for separately)

Ceiling or partition, Lunumedella, 1/2"planed, lapped and nailed to existing frames or underside of rafters, up to 1 square (Fillets and beadings paid for separately)

Ceiling or partition, Lunumedella, 1/2" beading and rebating, nailing to underside of existing joists, rafters or frames, above one square (Fillets and beadings, paid for separately)

Ceiling or partition, Lunumedella, 5/8" beading and rebating, nailing to underside of existing joists, rafters or frames, up to one square (Fillets and beadings, paid for separately)

Ceiling openings 2ft 0" x 1ft 6" approx., forming complete with 2" x 2" bearers. (Glass tiles or sheets paid for separately)

Ceiling Lunumedella 1/2" planks, lapped and nailed to framework consisting of finished size with 3 3/4" x 1 3/4" joists and 1 3/4" x 1 3/4" bearers in (Group 4,Category A) timber, Rate to include for 2 coats of wood preservatives to joists and bearers.

Ceiling Lunumedella 3/4" thick planks, lapped and nailed to framework consisting of finished size with 3 3/4" x 1 3/4" joists and 1 3/4" x 1 3/4" bearers in (Group 4,Category A) timber, Rate to include for 2 coats of wood preservatives to joists and bearers.

Partitions paneling 7 ft 0" to 10 ft 0" with 1/2" thick chipboard with finished size 3 3/4" x 1 3/4" and 3 3/4" x 3 3/4" upright fixed at 3ft 0" interval and 4" x 2" as horizontal members in (Group 4,Category A) timber. Rate to include for fixing chipboard to both sides. data 9ft 9"x7ft 0"=6

Partition - paneled with 3/8" chipboard with finished size 3' 3/4"x 1' 3/4"and 3' 3/4"x 3' 3/4" uprights fixing at 3' 0" interval sand 4"x 2" as horizontal members in (Group 4,Category A) timber. Rate to include for fixing chipboard to both sides. data 9ft 9"x7ft 0"=68.25 sq.ft

Partitions glazed 7ft -0" - 10ft -0" height 3/16" thick and paneling 1/2" thick plywood with finished size 3 3/4" x 2 3/4" and 3 3/4" x 3 3/4" upright at 3ft 0" intervals and 4" x 2" as horizontal members in (Group 4,Category A) timber. Rate to include for fixing chipboard to both sides of frame2"x1/2" (Group 4,Category A) timber boarding around glass pane.

Partitions glazed 7ft 0" - 10ft -0" height 3/16" thick and paneling 3/8" thick plywood with finished size 3 3/4" x 2 3/4" upright at 3ft 0" interval and 4" x 2" as horizontal members in (Group 4,Category A) timber. Rate to include for fixing chipboard to both sides of frame 2" x 1/2"


S07- 209


Partitions available fixing, including making good to walls and floors. sq.ft

sq.ft

sq.ftTimber Plugs

NosPlywood Panels

sq.ftCove, mouldings

L.ft

L.ftDoors or windows

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

Partitions, fully paneling, or paneling and glazing 1 1/8" thick with 4" x 2" frames and 1" x 1" quadrant fillets supplying and fixing complete with brass screws in (Group 4,Category A) local timber.

Partitions, glazing and paneling with plywood panels in (Group 4,Category A) timber (main posts 4" x 4" x 10ft 0" intermediate posts 4" x 2" x 7ft 0" approx., and 1 1/2" x 8" capping complete)

Plugs in (Group 4,Category A) timber, 4" long tapering 3" x 2" supplying and fixing to walls in cement mortar 1:3.

Plywood panels, 3 ply, supplying and fixing to existing frames (beadings to be paid for separately)

Cove, mouldings, Halmilla 2 1/2" x 1 1/2" fixing with brass screws and plugs new or renewing.

Cove, mouldings, Alstonia or equivalent 2 1/2" x 1 1/2" fixing with brass screws and plugs new or renewing.

Doors or windows, legging, bracing and battening with groove and tongue joints finished size 3 3/4" x 2 3/4" frames and 3/4" to 7/8" thick sashes in (Group 2,Category A) local timber complete with brass furniture(Rim lock, Hinges).( Door Size 2' 6"x6' 6" = 16¼s.ft)

Doors or windows, legging, bracing and battening with groove and tongue joints finished size 3 3/4" x 2 3/4" frames and 3/4" to 7/8" thick sashes in (Group 2,Category B) local timber complete with brass furniture.( Door Size 2' 6"x6'x 6" = 16¼s.ft)

Doors or windows ledging, bracing and battening, 3/4" to 7/8" thick sash only, in (Group 2,Category A) timber supplying and fixing with available (brass/Iron) furniture.

Doors or windows ledging, bracing and battening, 3/4" to 7/8" thick sash only, in (Group 2,Category B) timber supplying and fixing with available (brass/Iron) furniture.

Doors or windows, framing and battening, with finished size 3 3/4" x 2 3/4" frames and 1" to 1 1/8" sashes in (Group 2,Category A) local timber complete with brass furniture.

Doors or windows, framing and battening, with finished size 3 3/4" x 2 3/4" frames and 1" to 1 1/8" sashes in (Group 2,Category B) local timber complete with brass furniture.

Doors or windows, framing and battening, with finished size 3 3/4" x 2 3/4" frames and 1 1/4" to 1 1/2" sashes in (Group 2,Category A) local timber complete with brass furniture.

Doors or windows, framing and battening, with finished size 3 3/4" x 2 3/4" frames and 1 1/4" to 1 1/2" sashes in (Group 2,Category B) local timber complete with brass furniture.


S07- 210


sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ft

sq.ftDoor or Window, removing, easing and re-fixing. NosDoor or Window, easing only. Nos

L.ft

NosDoor or Window, Glazing bars renewing in (Group 2,Category A) timber.

L.ft

Nos

Doors or Windows, sash only 1" to 1 1/8" thick in (Group 2,Category A) timber supplying and fixing complete with available (brass/Iron)furniture.

Doors or Windows, framing and battening, sash only 1" to 1 1/8" thick in (Group 2,Category B) local timber, supplying and fixing complete with available (brass/Iron)furniture.

Doors or Windows, sash only 1 1/4" thick in (Group 2,Category A) timber supplying and fixing complete with available (brass/Iron)furniture.

Doors or Windows, sash only 1 1/4" to 1 1/2" thick in (Group 2,Category B) local timber supplying and fixing complete with available (brass/Iron) furniture.

Doors for garages, framing and battening in (Group 2,Category A) timber with 5" x 4" frames and 1 1/2" thick sashes supplying and fixing complete with iron pintols and strap hinges.

Doors or Windows, glazing and/or paneling with finished size 3 3/4" x 2 3/4" frames and 1 1/8" to 1 1/4" sashes in (Group 2,Category A) local timber supplying and fixing complete with brass furniture.

Doors or Windows, glazing and/or paneling with finished size 3 3/4" x 2 3/4" frames and 1 1/8" to 1 1/4" sashes in (Group 2,Category B) local timber supplying and fixing complete with brass furniture.

Doors or Windows, glazing and/or paneling, sash only 1 1/8" to 1 1/4" thick in (Group 2,Category A) timber with available (brass/Iron) furniture.

Doors or Windows, glazing and/or paneling, sash only 1 1/8" to 1 1/4" thick in (Group 2,Category B) timber with available (brass/Iron) furniture.

Doors paneling and trellising B.R.C. weld mesh No.32, with 4 3/4" x 2 3/4" frames and 1 1/8" thick sashes in (Group 2,Category A) timber, supplying and fixing complete with brass furniture.

Doors paneling and trellising B.R.C. weld mesh No.32 sash only 1 1/8",supplying and fixing with available (brass/Iron)furniture.

Doors, paneling and trellising/B.R.C. weld mesh No.32 sash only 1 1/4" thick in (Group 2,Category A) timber with available furniture.

Doors paneling with finished size 3 3/4" x 2 3/4" frames and 1 1/8" - 1 1/4" sashes in (Group 2,Category A) timber supplying and fixing complete with available (brass/Iron) furniture.

Door or Window frames renewing in short lengths with (Group 2,Category A) timber. assume 3ft length of door frame renewed. 5' x3'

Door or Window frame altering, existing rebate fillet using (Group 2,Category A) timber with screws and sashes rehung on opposite side.

Door Stops in (Group 2,Category A) timber 1 1/2" x 1 1/2" x 5" tapering, supplying and fixing.


S07- 211


Door or Window sashes, available, fixing in position (sash and fittings available at site) Nos

Door sashes swing, removing and re-fixing in new position. Nos

sq.ftDoors, swing 1" thick in (Group 2,Category A) timber with ( ¾") width Ply wood panels supplying and fixing complete with brass gravity hinges.


S07- 212


Door frame

L.ft

L.ft

sq.ft

sq.ft

sq.ft

sq.ftDoors or windows framing and battening sash

sq.ft

sq.ft

sq.ftDoors glazing and/or paneling

sq.ft

sq.ft

sq.ft

sq.ftDoor or Window frame

Door frame with finished size 3 3/4" x 2 3/4" in (Group 2,Category A) timber supplying & fixing in position. (data 2' 6"x 6' 6" =16.25s.ft or 16.5' ft long)

Door frame with finished size 3 3/4" x 1 3/4" in (Group 2,Category B) timber supplying and fixing in position. (data 2' 6"x 6' 6" =16.25s.ft or 16.5' ft long)

Plywood Door ** Note:(Brand - GINTOTA or equivalent)Door,1 1/4" thick plywood ordinary finish (Moisture Resistant) single sash, size 2' 9"x6' 9", hung on finished size 3 3/4" x 2 3/4" frame in (Group 2,Category A) timber and complete with brass furniture's. .(Door Lock paid Separately)

Door,1 1/4" thick plywood ordinary finish (Moisture Resistant) single sash, size 2' 9"x6' 9", hung on finished size 3 3/4" x 2 3/4" frame in (Group 2,Category B) timber and complete with brass furniture's. .(Door Lock paid Separately)

Supplying and fixing Door 1¼" thick, plywood, ordinary finish (Moisture Resistant), single sash, size 2' 9"x6' 9",hung to the existing frame including necessary brass fittings.(Door Lock paid Separately) data 2ft 9"x6ft 9"=18.56s.ft

Supplying & fixing ,1 1/4" thick Ply wood door, Both Side Luxury finish (Moisture Resistant) ,size 2' 9"x6' 9", single sash, hung to existing frame including necessary brass fittings.(Door Lock paid Separately) data 2ft 9"x6ft 9"=18.56s.ft

Doors or windows framing and battening finished size with 3 3/4" x 2 3/4" frames and 1 1/4" to 1 1/2" sashes in (Group 7, Category A) local timber complete with brass furniture.

Doors or windows framing and battening sash only 1" to 11/8" thick in (Group 7, Category A) timber supplying and fixing complete with available furniture.

Door or windows framing and battening sash only 1 1/4" to 1 1/2" thick in (Group 7, Category A) local timber supplying and fixing complete with available furniture.

Doors glazing and/or paneling finished size with 3 3/4"x2 3/4" frames and 1 1/8" to 1 1/4" thick sashes in (Group 7, Category A) timber supplying and fixing complete with brass furniture.

Doors glazing and/or paneling sash only 1 1/8" to 1 1/4" thick in (Group 7, Category A) timber special class with available ironmonger.

Windows glazing and paneling finished size with 3 3/ 4" x 2 3/4" frame and 1 1/8" to 1 1/4" thick sash in (Group 7, Category A) local timber supplying and fixing complete with brass furniture.

Windows glazed and paneled, sash only 1 1/8" to 1 1/4" thick in (Group 2, Category A) timber milla with available ironmonger.


S07- 213


sq.ft

sq.ftFillets, quadrant Fillets, quadrant 3/4" x 3/4" supplying and fixing with nails, in (Group 6, Category A) timber.

L.ftFillets, quadrant 1" x 1" in (Group 6, Category A) timber supplying and fixing with nails.

L.ftTimber Gate

sq.ft

sq.ft

sq.ft

sq.ft

NosLouver blades

L.ftLouver blades 3/8" minimum thickness in (Group 1, Category A) timber over 4" and up to 6".

L.ftLouver blades 3/8" minimum thickness in (Group 1, Category A) timber over 6" and up to 9".

L.ftWooden Posts

L.ft

L.ftPosts, Wooden, round jungle timber 5" minimum and average 6" dia. supplying and fixing.

L.ftReepers, timber

Door frame finished size with 3 3/4" x 2 3/4" in (Group 7, Category A) local timber supplied and fixed in position.

Window frames finished size with 3 3/ 4" x 2 3/4" in (Group 7, Category A) timber supplied and fixed in position.

Gate, 1 3/4" as per type plan for bungalow, 6 1/2" top rail, with 2 3/4" x 3/4" weather capping, 8" lock and bottom rails and styles, splay meeting styles, 2" x 1 1/4" verticals at 3 1/2" centers in groups of 3, panels of 4" x3/4" groove and tongued boards fixed raking, and 1/2" dia. tension bars fixed complete using available fittings.(Group 5, Category A) local timber.

Gate 1 3/4" thick for bungalows, 4" top rails and styles, 8" bottom rails, 3" braces, 1 3/4" x 1 3/4" and 1" x 1 1/4" verticals at 4" centers supplying and fixing complete using available fittings (Group 5, Category A) local timber.

Gate 1 1/2" thick, with 4" top and bottom rails, styles and braces and 2" x 1" laths fixing at 4" centers supplying fixing complete with available furniture (Group 5, Category A) local timber.

Gate 1 3/4" thick with 4" top and bottom rails, styles and braces, and 3/4" bars at 4" centers supplying fixing complete with available fittings (Group 5, Category A) local timber.

Gate sash with gate posts available at site, fixing complete including fixing post (Gate and Posts available).

Louver blades 3/8" minimum thickness in (Group 1, Category A) timber up to 4" width supplying and fixing.

Posts, veranda, 5" x 5" tapering to 4" x 4" in (Group3, Category A) timber, supplying and fixing on spur stones (spur stones paid for separately)

Posts, veranda 6" x 6" tapering to 5" x 5" in (Group3, Category A) timber supplying and fixing on spur stones (spur stones paid for separately)


S07- 214


L.ftReepers 2" x 1" in (Group3, Category B) local timber up to 100 L.ft: supplying and fixing.

L.ft

L.ft

L.ftReepers, available fixing with wire nails. L.ftRoof with sawn timber framework & Covering Tiles on it

Sqr

Sqr

Sqr

SqrShelving

sq.ft

sq.ftShelving of the types as per plan no 31638, 17988 removed and r3efixing new possession.

sq.ftSkirting Supplying and fixing Skirting in (Group5, Category A) board 3"x¾" on walls.

L.ft

L.ftOther Carpentry work.

cu.ftTimber, available, sorted out, cut to required sizes and fixing in roof and other carpentry work.

cu.ftcu.ft

cu.ft

cu.ft

Reepers 2" x 1" in (Group3, Category A) timber supplying and fixing new or renewing with iron nails, up to 100 L.ft: (Shifting of tiles to be paid for separately)

Reepers 2" x 1/2" in (Group3, Category A) timber supplying and fixing, new or renewing, with iron nails up to 100 L.ft: (Shifting of tiles to be paid for separately)

Reepers 2" x 1/2" in (Group3, Category A) timber supplying and fixing new or renewing, with iron nails over 100 L.ft:

Roof with Calicut pattern tiles on (Group3, Category A) sawn timber framework complete with ridges, hips etc.

Roof with Calicut pattern tiles on (Group3, Category B) sawn timber framework complete with ridges, hips etc.

Roof with half round tiles on (Group3, Category A) sawn timber framework complete with ridges, hips etc.

Roof with half round tiles on (Group3, Category B) timber framework complete with ridges, hips etc.

Shelving in (Group2, Category A) timber 1" thick on triangular brackets with 2 Nos. Horizontals 1 1/2" x 3/4" and 1 1/2" x 1/2" verticals and struts, and 2" x 1" skirting as per Type Plan 31638, supplying and fixing to walls with plugs. (Shelving area to be measured separately.

Shelving in (Group2, Category A) timber 1" thick framing with 2"x2" uprights and 2" x 2" horizontals and 2" x 1/2" skirting supplying and fixing to wall as per type plan 17988 Shelving area to be measured separately.

Supplying and fixing Skirting in (Group5, Category A) timber boards, 6"x ¾" on walls.

Timber available, sorted out, cut to required sizes and fixing in partitions and frames. per 10 L.ft 4x3 or 4/6 cu.ft

Timber, Milla, fixing or renewing in posts and frames. per .5 cu.ftTimber (Group 4,Category A), (excluding Milla) supplying and fixing new or renewing in partitions and frames, including panels and boards.

Timber (Group 4,Category B) supplying and fixing new or renewing in partitions and frames, including panels and boards.


S07- 215


Timber (Group 4,Category A) supplying and fixing new or renewing in, other carpentry work. cu.ft

Timber (Group 4,Category B) supplying and fixing new or renewing in, other carpentry work. cu.ft

Trellis

L.ft

L.ft

L.ft

L.ftTrellis laths 1" x 1" supplying and fixing. L.ftTrellis latches 2" x 1/2" in (Group 2,Category A)timber, renewing. L.ft

sq.ft

sq.ft

sq.ft

Trellis laths 1/2" x 1/2" renewing in (Group 2,Category A) local timber, in quantities (Over 100 L.ft)

Trellis laths 1/2" x 1/2" renewing in (Group 2,Category A) local timber, in quantities ( Up to 100 L.ft)

Trellis laths 1" x 1/2" renewing in (Group 2,Category A) local timber, in quantities over 100 L.ft:

Trellis laths 1" x 1/2" renewing in (Group 2,Category A) local timber, in small quantities up to 100 L.ft:

Trellis partition with 1/2" x 1/2" laths fixing 2" apart diagonally, horizontally or vertically, on 4" x 2" milla timber framing.

Trellis screens with laths 1 3/4" x 3/8" at 1 1/4" distance apart vertically and horizontally in Milla timber frames 1 1/2" x 2 1/2"supplying fixing to walls complete.

Trellis screens with laths 1" x 3/8" at 1 1/4" distance apart vertically and horizontally on Milla frames 3" x 1" supplying and fixing to walls complete.


S07- 216


J-IRONMONGERBolts and Nuts, IronBolts and Nuts, iron 1 3/4" x 1/4" with washers fixing complete. NosBolts and Nuts, iron 2 1/2" x 3/8" with washers fixing complete. NosBolts and Nuts, iron 5" x 3/8" with washers supplying and fixing complete.

NosBolts and Nuts, iron 9" x 3/8" with washers supplying and fixing complete.



NosBolts and Nuts, iron 12" x 5/8" with washers fixing complete. NosBolts tower, 3" Iron, heavy quality supplying and fixing with Iron screws. NosBolts tower, 4" Iron, heavy quality supplying and fixing with Iron screws. NosBolts tower, 5" Iron, heavy quality supplying and fixing with Iron screws. NosBolts tower, 6" Iron, heavy quality supplying and fixing with Iron screws. NosBolts tower, 2ft 9" Iron, heavy quality supplying and fixing with Iron screws.

NosIron Brackets

NosWeld mesh

sq.ft

sq.ft

sq.ftCabin HooksCabin Hooks and eyes, 2" Iron, supplying and fixing. setCabin Hooks and eyes, 3" Iron, supplying and fixing. setCabin Hooks and eyes, 6" Iron, supplying and fixing. setCabin Hooks and eyes, 8" Iron, supplying and fixing. setCabin Hooks and eyes, 9" Iron, supplying and fixing. setCasement StaysCasement Stays, Iron 10" heavy quality, supplying and fixing. NosCasement Stays, Iron 12" heavy quality, supplying and fixing. NosChimneyChimney flue pipe available, fixing only. L.ft

Brackets with 1 1/2" x 1/4" flat iron 3ft 6" long (approx.) fish tailed at ends, supplying and fixing to walls and walls made good.

2"x2" Weld mesh No.12, supplying and fixing to existing frames with staples (fillets and beadings to be paid for separately)

2"x2" Weld mesh No.10 supplying and fixing to window frames with 2" x 1/2" (Group 2) timber beadings, and painting weld mesh with 2 coats anti-corrosive paint, and beadings with primer, undercoat and 2 coats enamel paint to approved colour. Rate to include for making openings for bolts, casement stays etc.

2"x2" Weld mesh No.12 supplying and fixing to window frames with 2" x 1/2" (Group 2) timber beading, and painting weld mesh with 2 coats anti-corrosive paint, and beadings with primer, undercoat and 2 coats enamel paint to approved tint Rate to include for making openings for bolts, casement stays etc.


S07- 217


Chimney flue pipe 6" dia. making and fixing with G.I sheets 22 B.W.G. L.ft

L.ftCowel G.I 24 B.W.G making and fixing for 6" - 9" flue pipes. NosCowel G.I available, fixing complete for 6" -9" dia. flue pipes. Nos

sq.ft

sq.ft

sq.ftGate, Iron

sq.ftGutter HooksGutter Hooks or brackets 3/4" x 1/8" supplying and fixing complete with Iron screws.

NosHasp and staple

Nos

Nos

NosHinges (Iron)Hinges, butt, 2" iron of approved heavy quality supplying and fixing with iron screws.

pairsHinges, butt, 3" iron of approved quality supplying and fixing with iron screws.



pairsHinges supplied by Dept. fixing complete with screws. pairs

Nos

Nos

Nos

Nos

Chimney flue pipe 8"-12" dia making and fixing with G.I sheets 22 B.W.G (Sheets to be supplied by Department)

Expanded metal No.8" B.R.C Fabric supplying and laying as reinforcement in floor and foundation.

Expanded metal, zinc sheet, wire gauge etc. fixing with iron screws to existing frames with fillets or beadings ,fillets or beadings to be paid for separately, and expanded metal, zinc sheet, or wire gauge (available at site / supplied by the client).

Fly proofing, perforated zinc, 1/16" mesh, supplying and fixing to existing frames (fillets to be paid for separately)

Gate, iron, with 1 1/2" x 1 1/2" x 1/4" angle iron framework including bracing and horizontal center member, with 5/8" dia. M.S bars at 6" centers complete with strap hinges, hasp and staples.

Hasp and staple 4" iron, safety type of approved heavy quality, supplying and fixing with iron screws.

Hasp and staple 6" iron, safety type of approved heavy quality, supplying and fixing with iron screws complete.

Hasp and staple 12" x 2" iron, specially made out of 1/4" iron plate and fixing with 1/4" x 2" bolts and nuts complete.

Hinges, strap iron 1 1/2" x 1/4" x 1ft 0" long supplying & fixing with necessary bolts and nuts (excluding pintols)

Hinges, strap iron 2" x 1/4" 3ft 0" long supplying and fixing with necessary bolts and nuts (excluding pintols)

Hinges, double strap, 2 1/2" x 3/8" x 3ft 6" flat iron bent to shape and fixing complete with bolts and nuts as per plan 23097

Hinges, double strap, 2 1/2" x 3/8" x 5ft 6" flat iron bent to shape and fixing complete with bolts and nuts as per plan 23097


S07- 218


Hinges T 6" Iron, heavy quality supplying and fixing with iron screws complete. pairs

Hinges, T 7" Iron, heavy quality supplying and fixing with iron screws complete. pairs





Hinges, spring, Japanese Helical, door supplying and fixing with iron screws complete. Nos

Hinges (Stainless Steel) for Timber Doors

pairs

pairsHoldfastHoldfast 1/8" x 2" x 9" flat iron supplying and fixing complete. per No. Nos

NosLocks (iron)Note: Refer Item numbers From K039 to K058 for (Brass / Quality) Locks

Keys, Iron for door locks making and supplying. NosKeys, Iron for cupboards, making and supplying. NosLocks, available, fixing with screws. NosLocks, repairing and re-fixing. Nos

Nos

Nos

Nos

NosLocks, Bird type supplying and fixing with iron screws complete. NosMild steel rods

cwt

cwt

cwt

Supplying and fixing UNION Butt Hinges, , 102x76x 3mm (thick) 2BB stainless steel, for wooden doors with brass screws.

Supplying and fixing UNION Butt Hinges, , 102x76x 2mm (thick) 2BB stainless steel, for wooden doors with brass screws.

Iron rods supplying by the client, cut to correct lengths, inserted in window frames and painted with 2 coats anti-corrosive paint.

Locks, rim, 4" iron, superior quality, heavy type supplying and fixing with iron screws complete.

Locks, rim, 6" iron, superior quality, heavy type supplying and fixing with iron screws complete.

Locks, Motice, 4" iron, superior quality, heavy type supplying and fixing with iron screws complete.

Locks, Motice, 6" iron, superior quality, heavy type supplying and fixing with iron screws complete.

Mild steel rods in reinforcing lintols, beams, columns and slabs, bending to shape, laying in position and tying with G.I wire as directed.

Mild steel rods in foundation bending to shape, laying in position and tying with G.I wire as directed.

M.S rods available., bending to shape, tying with G.I wire and laying in position as directed in reinforcing lintols beams and floors.


S07- 219


cwt

L.ft

L.ft

NosRag Bolts 4" x 5/8" with nuts and washers supplying and fixing complete. Nos

sq.ftWire meshWire netting, hexagonal mesh 1/2" supplying and fixing (beading to be paid for separately)

sq.ft

sq.ft

sq.ft

sq.ft Reinforcement, with Tor steel rods

cwt

cwtChain-link fencingNote: Refer Item numbers From S011 to S024 for Barbed wire fencing

L.ft

sq.ft

sq.ft

L.ftMild Steel Grill work

M.S rods available, bending to shape, tying with G.I wire and laying in position as directed reinforcing foundations.

M.S bars 5/8" dia. supplying and fixing in window frames at 4" centers and painted with two coats Aluminium or anticorrosive paint.

M.S bars 3/4" dia. supplying and fixing in window frames at 4" centers and painted with two coats Aluminium or anticorrosive paint.

Pintols for gates and garage doors supplying and fixing in cement concrete (concrete to be paid for separately)

Sheets, G.I plain, 24 B..W.G with hooked joints supplying and fixing to existing frames with wire nails.

Wire mesh 1/2" galvanized, supplying and fixing with available fillets, including removing existing.

Wire mesh 1/4" galvanized, supplying and fixing with available fillets, including removing existing.

Wire mesh 1/16" galvanized, supplying and fixing with available fillets including removing existing.

Tor steel rods in reinforcing lintols, beams, columns and slabs bending to shape, laying in position and tying with G.I wire as directed.

Tor steel rods in foundation or Floors, bending to shape, laying in position and tying with G.I wire as directed.

Supplying and fixing 2"dia. heavy duty GI pipe uprights for receiving chain-link fence. Rate to include for painting one coat of anticorrosive and two coats of enamel paint and welding 6"x6"x1/4" thick MS plate to bottom of pipe and fixing fiberglass pipe cap 2" dia.(Rate exclude cement concrete base & Excavation.)

Supplying and fixing, open area 2"x2", 5' 0"ft. high (gauge 10) galvanized and PVC coated Chain link fence . Fixed to existing GI post and including horizontal bracing with 5/8"x 1/4" MS flat iron with GI J bolts and washers , PVC coated tying wires etc.,

Supplying and fixing, open area 2"x2", 5' 0"ft. high (gauge 12 galvanized and PVC coated Chain link fence . Fixed to existing GI post and including horizontal bracing with 5/8"x 1/4" MS flat iron with GI J bolts and washers , PVC coated tying wires etc.,

Supplying and welding 11/2"x11/2"x1/4"MS angle iron horizontal bracing to existing GI pipe posts. Rate to include for painting one coat of anticorrosive paint and two coats of enamel paint.


S07- 220


sq.ft Guard rails ( Heavy duty GI-Pipe)

L.ftHand rails ( Heavy duty GI-Pipe)

L.ft Hand rails (Stainless Steel, 1.5mm thick Pipe- Grade 304 )

L.ftWeb Truss - Fabricating, Hoisting & FixingAs per Drg.No 2013-TP-ST11 & 2013 - TP- ST12

Nr.

Nr.

Nr.

Nr.

Nr.

Nr.

As per Drg.No 2013-TP-ST13 - 2013 - TP- ST18

Fabricating and fixing of MS grills with 1"x1/4" flat iron frame and 1/4"dia.MS. rods welded to diamond shape 3"centres both ways.

Fabricating and fixing of 3' 0" high, heavy duty GI. Pipe Guard railing, consisting of 1½"dia.Vertical pipe (Balusters) raised at 6" intervals & firmly fixed to Concrete floor at bottom & welded to 2"dia.heavy duty Horizontal GI. pipe top rail. Two rows of 1" dia. heavy duty GI pipe bracings welded to Vertical pipes horizontally at mid way.( painting Paid Separately)Considered 20' 0" long hand rail

Fabricating and fixing of 3' 0" high, heavy duty GI. Pipe Hand railing, consisting of ¾" dia. uprights at 12" centers. 1/4" thick 2"x2" M.S plate welded to the bottom end of uprights and embedded in concrete floor. The top end of the upright welded to 1½"dia.G.I hand rail. Considered 11' 2" long hand rail

Fabricating and fixing of 3' 0" high, stainless steel railing, consisting of ¾" dia 1.5mm Thick stainless steel (Pipe) uprights at 12" centers. 1/4" thick 2"x2" M.S plate welded to the bottom end of uprights and embedded in concrete floor, covered with stainless steel base cap. The top end of the upright welded to Stainless Steel Pipes,1½"dia.x 1.5mm Thick , hand rail (All stainless steel members are in Grade 304). Considered 11' 2" long hand rail

Fabricating, Hoisting & Fixing Steel web Truss , Span - 5m consist of 2 Nos of 50 x 50 x 6mm top chord , 2 Nos of 50 x 50 x 6mm bottom chord & 50 x 50 x 6mm bracings. Including all , gusset plates , cleats , rivets , nuts, washers, rag bolts, separators etc.. (Rate shall include for painting of two coats of anticorrosive paint & one coat of enamel paint.) (Hoisting up to 30 ft)

Steel web truss Type T1 with Roof Angle - 150 (Approx. Weight 0.25 M.T)







S07- 221


Nr.

Nr.

Nr.

Nr.

Nr.

Nr.

Nr.

Nr.

Nr.

Nr.

Nr.















S07- 222


K-BRASS FOUNDER

NosBolts, barrel, brassBolts, barrel, brass, polished, 2 1/2" heavy quality supplying and fixing with brass screws.

NosBolts, barrel, brass, polished, 3" heavy quality supplying and fixing with brass screws.




NosBolts, brass, skeleton 8" supplying & fixing with brass screws. NosBolts, brass, skeleton 10" supplying & fixing with brass screws. NosBolts, brass, skeleton 12" supplying & fixing with brass screws. NosBolts, brass, skeleton 14" supplying & fixing with brass screws. NosCabin Hooks (Brass)Cabin Hooks 2" polished, brass, heavy quality supplying and fixing with brass screws.

NosCabin Hooks 3" polished, brass, heavy quality supplying and fixing with brass screws.

NosCabin Hooks 6" polished, brass, heavy quality supplying and fixing with brass screws.

NosCabin Hooks, 8", polished, brass heavy Quality supplying & fixing with brass screws.

NosCabin Hooks, 9", polished, brass heavy quality supplying & fixing with brass screws.



NosCasement fasteners, brass

NosCasement stays, polished 10" heavy quality supplying and fixing. NosCasement stays, polished 12" heavy quality supplying and fixing. NosFanlight Catches, brass heavy quality, supplying and fixing with brass screws complete.

NosHandles, door, brass, polished heavy quality supplying and fixing with brass screws complete.

NosHasp and staple, brass

Nos

Bolts, Casement fasteners or stays, removing and re-fixing including making good to holes in frames and sashes.

Casement fasteners, brass with Motice plate, polished heavy quality supplying and fixing with brass screws.

Hasp and staple, Safety type, 6" brass, polished heavy quality supplying and fixing with brass screws, complete.


S07- 223


NosHat Hooks, brass, supplying and fixing with brass screws. NosHinges, brass

pairs

pairs

pairs

pairs

pairs

pairsHinges, gravity, brass supplying and fixing with brass screws complete. pairs

pairs

Nos

NosHinges, Spring, available, repairing and re-fixing. NosHinges, spring, double acting, brass 4" supplying and fixing. Nosfixing Hinges, available complete with brass screws. NosLocks (Brass)

Keys, brass for door locks, making and supplying. NosKnobs for door locks, polished brass, heavy quality, renewing with brass screws.

setLocks, door, available, fixing with screws. NosLocks, door repairing and re-fixing. NosLocks, cupboards, 2 1/2" brass, 4 levers with brass screws supplying and fixing complete.

NosLocks, cupboard, repairing and re-fixing. Nos

NosLocks, rim 5" single lever of best quality local manufacture, supplying and fixing.

NosSupplying and fixing ,night latch/Rim Lock (Duplicate/Local), with duplicate keys.

Nos

Hasp and staple, Safety type, 4" brass, polished heavy quality supplying and fixing with brass screws, complete.

Hinges, butt, 2" brass, polished heavy quality supplying and fixing with brass screws complete.

Hinges, butt, 3" brass polished heavy quality supplying and fixing with brass screws complete.

Hinges, butt, 3 1/2" brass polished heavy quality supplying and fixing with brass screws complete.



Hinges center pivoted (consisting of 2 pieces) brass, polished heavy quality supplying and fixing with brass screws complete.

Hinges, Parliamentary, 4" brass, polished heavy quality supplying and fixing with brass screws complete.



Note: Refer Item numbers From J057 to J065 for Iron Locks.& Item numbers From U743 to upward for Aluminium Door Locks.

Locks, rim 6" polished brass, 2 levers, superior quality and English make, supplying and fixing.


S07- 224


Nos

Nos

NosSupplying & fixing Motice (local) single Lock. NosSupplying and fixing Motice Lock (local) double. Nos

Nos

Nos

Nos

Nos

NosSupplying and fixing RANIYO-PADMA Handle - Black (On Plate) Nos

Supplying and fixing , Yale or Union, night latch Lock (Rim Lock), with duplicate keys. (Nos: 80 or 89),(Imported, British or south African make)

Supplying and fixing Union, night latch Lock (Rim Lock), with duplicate keys. (Nos: 1022,1027 or 1028),(Imported, British or south African make)

Door rings, brass 1 3/4" to 1 1/2" supplying and fixing to doors and windows with brass screws.

Supplying and fixing two Lever single door UNION Motice Lock (No2295),(Imported, British or south African make).

Supplying and fixing two Lever double door UNION Motice Lock (No2242), (Imported, British or south African make).

Supplying and fixing UNION Cylinder Lock (No: PC 064 SC) including Door handle pair,(Imported, British or south African make).

Supplying and fixing UNION Nob set Lock (No:X96300) (Imported, British or south African make).

Supplying and fixing UNION Nob set Lock for Toilets (No:X96350) (Imported, British or south African make).


S07- 225


L-PLASTERER

Sqr

SqrSqr

SqrSqr

Cove moulding 2 1/2" x 2 1/2" in cement mortar 1:2 built in existing wall. L.ft

L.ftCresting with broken glass in cement mortar 1:4 on coping of boundary wall.

L.ft Moulding

L.ft

L.ftMoulding 4" x 2" in cement and sand 1:2 built in existing wall. L.ft

L.ft

Nos

SqrPointing flush in cement 1:2 in surface cracks including raking out joints. L.ftPointing, tuck, projected in cement 1:2 on brick masonry etc. sq.ftRendering CementRendering, (1/2") thick, 1:2 cement and sand, above 1 square. SqrRendering, (1/2") thick, 1:2 cement and sand, up to 1 square. SqrRendering, (1/2") thick, 1:3 cement and sand, above 1 square. SqrRendering, (1/2") thick, 1:3 cement and sand, up to 1 square. SqrRendering, (3/4") thick, 1:2 cement and sand , above 1 square. SqrRendering, (3/4") thick, 1:2 cement and sand ,up to 1 Square. SqrRendering, (3/4") thick, 1:3 cement and sand , above 1 square. SqrRendering, (3/4") thick, 1:3 cement and sand ,up to 1 square. SqrCement floating coat.

Sqr

Sqr

Plastering (walls)(5/8") thick plastering to wall in cement lime and sand 1:1:5 finished semi rough with wooden float.

(5/8") thick plastering to wall in cement lime and sand 1:1:5 finished smooth with lime putty floating.

(5/8") thick plastering 1:5 cement and sand semi rough Plastering (beams, slab soffits)3/8" thick plastering to R.C.C. beams, slab soffit in cement and sand 1:3 including floating with lime putty.

Clay plastering and lime puttying smooth.

Repairing cracks in wall, plastered in cement mortar 1:3 after chipping 2" to 4" wide.

Moulding 3" x 1/2" in walls in lime and cement mortar 1:1:4 only for replacements to match existing or to be "extra" over rate for plastering.

Moulding 6" x 1" in walls in lime and cement mortar 1:1:4 only for replacements to match existing or to be "extra" over rate for plastering.

Flashing or plaster bands laid over tiles 4" to 6" wide on roof in cement and lime mortar 1:1:4.

Letters embossed in plaster 3/4" thick up to 6" high in cement and sand 1:2 cement floated and painted complete.

( 5/8") thick plastering to walls in lime and sand 2:5 including floating, finished smooth with lime putty.

Neat cement floating coat on already Layed rendering surface, finish smooth with Mason trowel.

Coloured cement (Red or Black) floating coat on already Layed rendering surface, finish smooth with Mason trowel.


S07- 226


SqrColoured cement (Brown or Green) floating coat on already Layed rendering surface, finish smooth with Mason trowel.


S07- 227


Cement Rendering and smooth Coloured floating coat

SqrRendering Cement with PudloRendering cement 3/4" 1:2 with Pudlo, 5 lbs. to 100 lbs., cement. SqrSkirting in cement mortar

L.ft

L.ftD.P.C- 3/4"

Sqr

L.ftL.ft

Rendering (3/4") thick, 1:3 cement and sand and floating coat, using Coloured (Red/Black) finished smooth with Mason trowel.

Skirting in cement mortar 1:3, 1/2" x 4" projected or flushed with wall, and finished with neat Cement smooth and including forming groove.

Skirting in cement mortar 1:3, 1/2" x 4" projected or flushed with wall, and finished with Red Cement floating, including forming groove.

D.P.C- 3/4" thick in cement, sand 1:2 finished smooth with 2 coats of hot tar.

Plastering (Reveals)Plastering external reveals 4" wide finished rough. Plastering internal reveals 4" wide finished smooth.


S07- 228


M-TINKERGI-Down pipes / Hold fasts

L.ft

L.ft

L.ft

L.ftExtra over Items 1 - 4 in Two storeyed buildings. L.ftExtra over Items 1 - 4 in buildings of Three or more storeys. L.ft

L.ftG.I Flashing

L.ftFlashing G.I refixing, including making good to walls in cement and lime mortar.

L.ftZn/Al-Flashing

L.ftG.I semicircular Gutters

L.ft

L.ftGutter, eaves 6" moulded, G.I 22 B.W.G making and fixing complete including brackets.

L.ftGutters, eaves and down pipes, cleaning in Single Storeyed Buildings. L.ftGutters, eaves and down pipes, cleaning in Two Storey Buildings. L.ftGutters eaves. re-grading in Single Storeyed Buildings. L.ftGutters eaves. re-grading in Two Storeyed Buildings. L.ft

NosGutter heads, 10" x 10" x 2ft 0" making of G.I Sheets 22 B.W.G and fixing.

Nos

NosMaking and fixing Gutter heads, 9" x 9" x 1ft 0" of G.I Sheets 22 B.W.G .

Nos

Making and fixing Down pipes 4" dia. Using G.I 22 B.W.G with holdfasts or plugs fixed to walls in cement 1:3.

Making and fixing Down pipes 6" dia. Using G.I 22 B.W.G with holdfasts or plugs fixing to walls in cement 1:3.

Making and fixing Down pipes, rectangular, using G.I 22 B.W.G. 4" x 3" with holdfasts or plugs fixing to walls in cement 1:3.

Making and fixing Down pipes 4" x 6", circular or Rectangular, with holdfasts or plugs fixing to walls (G.I sheets available)

Down pipes, loose or new, fixing with holdfasts or plugs including making good to walls (down pipes available; Plugs or holdfast to be paid for separately.

Flashing, G.I 22 B.W.G 1ft 6" wide, supplying and fixing with 6" turning up along, and top edge tucking well into wall in cement and lime mortar, including removal of old flashing.

Flashing, 0.47mm thick, Hi Tensile Zn/Al , 1'-6" wide, supplying and fixing with 0'-6" turning up along, and top edge tucking well into wall and groove filled with silicon.

Gutters, eaves 6" G.I semicircular 22 B.W.G making and fixing with hooks or brackets and screws, and joints to be soldered complete.

Gutters, eaves 6" G.I semicircular 22 B.W.G making and fixing with hooks or brackets and screws, and joints to be soldered complete. (G.I sheets available).

Gutters, existing, making opening to receive 4" to 6" down pipe, attaching spigot piece, joints to be soldered and making good.

Gutter heads, 10" x 10" x 2ft 0" making of G.I Sheets 22 B.W.G and fixing. (Sheets available)


S07- 229


Making and fixing Gutter heads, 9" x 9" x 1ft 0" of G.I Sheets 22 B.W.G . (Sheets available.) Nos

Gutter hooks or brackets 3/4" x 1/8" supplying and fixing complete with Iron screws. Nos

Gutters, leaks repairing or joints to be soldered. Nos

L.ft

L.ft

L.ftRenewing swan Neck approx. 3ft 4" long 4" dia. 22 B.W.G . Nos

Nos

L.ftValley gutter (G.I)

L.ftZinc Aluminium Colour bonded valley gutter (0.47mm)

L.ft

L.ft Zn/Alu high tensile down pipes

L.ft

L.ft Zn/Alu gutters

L.ftSupplying, fixing 0.47mm tk., Alu gutters (457mm girth) with brackets & specials.

L.ft Zn/Alu Down pipe Bends

Nos

Nos

Gutters, parapet, G.I 3ft 0" overall, 22 B.W.G renewing on existing boards, joints to be soldered and laid complete.

Renewing gutters, valley, 18 B.W.G 36" wide, on existing boards, sheets to be tarred, joints to be soldered and cement, lime filleting complete.

Renewing gutters, valley, 18 B.W.G 36" wide, on existing boards, sheets to be tarred, joints to be soldered and cement lime filleting complete (G.I sheets available)

Making tank, Hot Water, 1ft 6" x 1ft 0" x 1ft 6" high with G.I Sheets, 22 B.W.G riveting and soldering, supplying and fixing (Connecting U pipe and tap to be paid for separately)

Gutters parapet - G.I 3ft 0" overall 22 B.W.G renewing including timber 1" boarding, joints to be soldered and laid complete.

Gutters valley, 18 B.W.G 36" wide, renewing including timber 1" thick boarding, sheet t be tarred, joints to be soldered and cement lime filleting complete.

Supplying and fixing Zinc Aluminium sheet valley gutter (0.47mm) thick ,width 914mm and fixing to roof with self trapping screws.(Excluding timber boarding). Hi-tensile (Grade-550) Colour

Supplying and fixing Zinc Aluminium sheet valley gutter (0.47mm) thick ,width 457mm and fixing to roof with self trapping screws.(Excluding timber boarding) Hi-tensile (Grade-550) Colour

Supplying, fixing 0.47mm tk., Zn/Alu Hi-tensile (Grade-550) Colour down pipe (914mm girth) with brackets.

Supplying, fixing 0.47mm tk., Zn/Alu Hi-tensile (Grade-550) Colour down pipe (457mm girth) with brackets.

Supplying, fixing 0.47mm tk., Alu gutters (914mm girth) with brackets & specials. Hi-tensile (Grade-550) Colour

Supplying, fixing 0.47mm tk., Zn/Alu Hi-tensile (Grade-550) Colour. Down pipe Bend (for 914mm girth gutter) with brackets & specials.

Supplying, fixing 0.47mm tk., Zn/Alu Hi-tensile (Grade-550) Colour. Down pipe Bend (for 457mm girth gutter) with brackets & specials.


S07- 230


N-GLAZERGlass panes fixing with (Group 6 category A) timber beadings (Glass available)

sq.ftGlass panes 3 mm clear supplying and fixing with (Group 6 category A) timber beadings.

sq.ftGlass panes 5 mm clear, supplying and fixing with (Group 6,category A) timber Beadings.

sq.ft

sq.ft

sq.ftPaint removing from painted glass panes with Caustic Soda Solution or other paint remover.

sq.ft

Glass panes 5 mm pinhead or obscure supplying and fixing with (Group 6 category A) timber beadings.

Glass panes 3 mm pinhead or obscure supplying and fixing with (Group 6 category A) timber beadings.


S07- 231


P-PAINTER & DECORATOR

Scraping Walls

Sqr

Sqr

Sqr

Sqr

Sqr

Sqr Skim coat

Sq.ftCement washing to wallsCement washing to walls of single storeyed buildings, 1 coat, patching and preparing surface.

SqrCement washing to walls of single storeyed buildings, 2 coat, patching and preparing surface.

SqrCement washing externally to walls of building with upper floors, 1 coat. SqrWhite or colour washing walls

Sqr

SqrWhite or Colour washing external walls of two storeyed buildings, 1 coat.

Sqr

Walls, scraped to original plaster, sand papering and lime putting cracks and defects, preparing surface for Distemper, snowcem, paint or similar application.

Walls, scraping and removing soot and leveling internally in Kitchen (extra over colour washing)

Surface preparation (Old work) for Painting (Scraping /Patching /Smoothing)

Surface preparation, old work of Internal faces of walls, scraped to original plaster, patching up cracks and defects, with Acrylic wall putty, applying one coat of Acrylic wall Filler, sand papering and preparation of surface for application of Emulsion or Enamel paint. ( Painting Paid Separately)

Surface preparation, old work of External faces of walls, scraped to original plaster, patching up cracks and defects, with Acrylic wall putty, sand papering and preparation of surface for application of Weather Shield or Enamel paint. ( Painting Paid Separately)

Surface preparation, old work of External faces of walls, scraped to original plaster, patching up cracks and defects, with Acrylic wall putty, sand papering and preparation of surface for application of Weather Shield or Enamel paint in Two Storied building.( Painting Paid Separately)

Surface preparation, old work of External faces of walls, scraped to original plaster, patching up cracks and defects, with Acrylic wall putty, sand papering and preparation of surface for application of Weather Shield or Enamel paint in more than Two Storied building. ( Painting Paid Separately)

Applying Skim Coat compound on walls or soffit two coats, finished smooth with sand papering, and prepare for colour washing.

White or colour washing walls of single storeyed buildings 1 coat, including patching up and preparing surface.

White or colour washing walls of single storeyed buildings 2 coats, including patching up and preparing surface.


S07- 232


White or Colour washing external walls in buildings, of more than 2 storeys, 1 coat.Sqr

White or Colour washing external walls in Two storeyed buildings, 2 coats. Sqr

White or Colour washing external walls in building with more than 2 storeys, 2 coats.Sqr

Snowcem paintPainting walls with snowcem or equivalent cement paint, 2 coats to new work.

Sqr

Sqr

SqrAcrylic wall Filler ( Primer for Interior)Painting walls with Acrylic wall Filler. (CIC or Equivalent.) SqrAlkali resisting primerPainting walls with alkali resisting primer where necessary. (CIC or Equip)

SqrElastometic filler PrimerPainting walls with one coat of Elastometic filler Primer where necessary. (CIC or Equivalent.)

SqrAlkali resisting water Proofing sealer

SqrHeat Resistant paint

SqrSilicone masonry water repellent paintPainting Walls with one coat of Silicone masonry water repellent paint. SqrBathroom paintPainting Walls with one coat of Bathroom paint. (CIC or Equivalent.) SqrEmulsion paint (Interior)

Sqr

Sqr

Sqr

SqrPainting General Purpose weather shied ( Exterior)

Sqr

Sqr

Painting walls with snowcem or equivalent cement paint, 2 coats to old walls after scraping existing colour wash, sand papering and wiping down.

Painting walls with snowcem or equivalent cement on old walls after scraping existing colour wash, sand papering and wiping down one coat.

Painting walls with one coat of Alkali resisting water Proofing sealer where necessary. (CIC or Equivalent.)

Applying Heat Resistant paint, one coat to all exposed surfaces on walls already prepared. (CIC or Equivalent.)

Painting Walls with one coat of emulsion paint. (On New work or already prepared old work). (CIC or Equivalent.)

Painting on New walls with two coats of emulsion paint. (Primer coat paid separately) (CIC or Equivalent.)

Painting Walls with Emulsion paint, One coat including preparing surface of old work. (CIC or Equivalent.)

Painting Walls with Emulsion paint, Two coats including preparing surface of old work. (CIC or Equivalent.)

Painting external walls with One coat of weather shied paint. (Excluding Primer Coat). (CIC or Equivalent.)

Painting external walls with Two coats of weather shied paint. (Excluding Primer Coat). (CIC or Equivalent.)


S07- 233


Sqr

Sqr

Sqr

SqrAcrylic Emulsion (Exterior paint)

SqrPainting asbestos sheet roof

Sqr

Sqr

Sqr

SqrFloor Painting

Sqr

SqrEpoxy Floor Painting

Sqr

SqrAnticorrosive paint

Sqr

SqrPainting on GI Surface

Sqr

Painting on old work with General Purpose weather shied (Exterior paint) , including surface preparation.

Painting walls with weather shied paint One coat including wire brushing and sand papering of old work. (CIC or Equivalent.)

Painting walls with weather shied paint Two coat including wire brushing and sand papering of old work. (CIC or Equivalent.)

Painting on New work with, Two Coats of Acrylic Emulsion weather shied (Exterior paint), and One coat of Elastometic filler Primer (under Coat).

Painting on New work, weather shied (Exterior paint) One Coat, with One Primer under Coat. -(CIC or Equivalent.)

Painting on New work, weather shied (Exterior paint) Two Coats , with One Primer under Coat. -(CIC or Equivalent.)

Painting external walls with Two coats of Acrylic Emulsion (Exterior paint) paint resist against algae, fungus and scrubs. (On New work or already prepared old work). -(CIC or Equivalent.)

Painting over the asbestos sheet roof with Two coats of roof shield paint. (CIC or Equivalent.)

Painting under side of asbestos roofing sheet with One coat of emulsion paint (CIC or Equivalent.)

Painting under side of asbestos roofing sheet with Two coats of emulsion paint (CIC or Equivalent.)

Painting under side of asbestos roofing sheet with One coat of primer after preparing surface (CIC or Equivalent.)

Painting floors with One coat of quick drying Floor paint including washing, cleaning and smoothing down the surface. (CIC or Equivalent.)

Painting floors with Two coats of quick drying Floor paint including washing, cleaning and smoothing down the surface. (CIC or Equivalent.)

Painting floors with One coat of Epoxy Floor Paint including washing, cleaning and smoothing down the surface. (CIC or Equivalent.)

Painting floors with Two coats of Epoxy Floor Paint including washing, cleaning and smoothing down the surface. (CIC or Equivalent.)

Painting steelwork, One coat with anticorrosive paint including removing scale and wire brushing. (CIC or Equivalent.)

Painting steelwork, Two coats, with anticorrosive paint including removing scale and wire brushing. (CIC or Equivalent.)

Painting new galvanized iron GI Adhesion Promoter One coat and One coat of Dulux metal primer Zink chromate or duco oil primer or equivalent including washing surface with water after manufactures specification.


S07- 234


Aluminium paintSqrL.ftL.ft

Aluminium paint, One coat on metal surfaces. (CIC or Equivalent.)Aluminium paint, One coat, along 2" thick band. (CIC or Equivalent.)Aluminium paint, Two coats, along 2" thick band. (CIC or Equivalent.)


S07- 235


Enamel paint

Sqr

SqrRemoval of Paint from timber. Paint removed entirely with blow lamp to bare timber. Sqr

L.ftWood preservative Wood preservative, (clear) applied to woodwork one coat (old work) (CIC or Equivalent.)

SqrWood preservative, (clear) applied to woodwork two coats (New work) (CIC or Equivalent.)

SqrEnamel paint with Wood primer Under coat

SqrPainting new woodwork with approved primer, one coat. (CIC or Equivalent.)

SqrPolishing wood work with Wax

SqrPainting with Wood sheen

Sqr

SqrPolyurethane Varnishing

Sqr

Sqr

Sqrpolyurethane varnish-Matt

Sqr

SqrRemoving VarnishVarnishing, removing entirely to bare timber and preparing surface. SqrPainting with Sanding sealer / Woof finish Lacquer

Sqr

Sqr

Painting One coat of Enamel paint, including washing and cleaning the surface. (CIC or Equivalent.)

Painting Two coats of Enamel paint, including washing and cleaning the surface. (CIC or Equivalent.)

Painting G.I pipes 3/4" to 1/2" with approved paint, 2 coats.

Painting new woodwork, with primer, undercoat and Two coats of enamel paint. (CIC or Equivalent.)

Polishing Woodwork with Wax, including thoroughly sand papering surface in new work only of permanent fixtures.

Painting with Wood sheen paint including washing cleaning and smoothing down surface, One coat.

Painting with wood sheen paint including washing cleaning and smoothing down surface, Two coats.

Varnishing on old wood surface with one coat of polyurethane varnish-Gloss, after washing down and sand papering.

Varnishing on old wood surface with two coats of polyurethane varnish-Gloss, after washing down and sand papering.

Varnishing on New wood work with one coat of sanding sealer and two coats of polyurethane varnish-Gloss, after sand papering.

Varnishing with polyurethane varnish-Matt, after washing down and sand papering, Two coats.

Varnishing on New wood work with one coat of sanding sealer and two coats of polyurethane varnish-Matt, after sand papering.

Applying new woodwork with Two coats of Sanding sealer and two coats of wood finish

Applying wood finish, one coat, including washing, cleaning and smoothing down surface.


S07- 236


SqrApplying wood finish, one coat, including two coats of sanding sealer after washing, cleaning and smoothing down surface.


S07- 237


Painting with Perque varnish

Sq.ftSqr

Painting Letters on (Board / Wall)Lettering 1" to 1 1/2" painted in Sinhalese, English or Tamil, including painting background.

NosLettering 2" to 3" painted in Sinhalese, English or Tamil, including painting background.

NosLettering 4" to 5" painted in Sinhalese, English or Tamil, including painting background.

Nos

Cutting, leveling ,polishing and applying two coats of Perque varnish for an existing timber base floor.

Applying masonry sealer for walls One coat.


S07- 238


Q-PLUMBERBall valve-UPVC

NosSupplying & fixing UPVC ball valve 3/4" dia. (S-Lon or equivalent) NosSupplying & fixing UPVC ball valve 1" dia. (S-Lon or equivalent) NosSupplying & fixing UPVC ball valve 1 1/4" dia. (S-Lon or equivalent)

NosFixing ball valve 1/2" to 1" (available.) NosBall valve-BrassRepairing & fixing ball valve. removing and refixing NosSupplying & fixing Brass Ball valve ½" or 20mm-(Peglar or equivalent.) NosSupplying & fixing Ball valve Brass ¾" or 25mm-(Peglar or equivalent.) NosSupplying & fixing Ball valve Brass 1" or 32mm-(Peglar or equivalent.) Nos

NosSoldering & fixing ball to lever operating Valve (available) NosConcealed Taps/Valves-Chromium platedSupply and fixing concealed valve 1/2"dia. NosSupplying and fixing Concealed valve 1/2"dia.(American Standard or Equivalent.)

Nos

Supplying & fixing Concealed Taps/Valves-Chromium plated ½" dia.(Plumber)Nos

Flush valveSupplying and fixing cobra flush valve NosSupplying and fixing wall Urinal Flush Valve(FM 3A903)-High Quality Nos

Supplying and fixing wall Urinal Sensor Flush Valve(FM 3L303)-High QualityNos

Flush valve to existing Urinal (Imported )Supplying and fixing wall Urinal Flush Valve(Cobra)-High Quality Nos

Supplying & fixing flush valve to existing Urinal (American Standard or Equivalent.)Nos

Gate valve brass for Max. 17.5 bars (Pegler 1065 or equivalent)

Nos

Supplying & fixing UPVC ball valve 1/2" dia. (S-Lon or equivalent)

Supplying & fixing Ball valve Brass 1½" or 63mm -(Peglar or equivalent.) with necessary fittings.

Prime cost of 1/2" dia: chromium Concealed valve (American Standard) Rs4,450 ** (2665)

Prime cost of bib tap, Concealed Taps/Valves-Chromium plated ½" dia.(Plumber) Rs 1890 ** (1878)

Prime cost of wall Urinal Flush Valve(Rocell)-High Quality with brackets. .Rs.6,328 ** (2817)

Prime cost of wall Sensor Flush Valve(Rocell)-High Quality with brackets. .Rs.18,180 ** (2818)

Prime cost of wall Urinal Flush Valve(Cobra)-High Quality with brackets. .Rs.9,500 ** (2626)

Prime cost of flush valve to existing Urinal (American Standard).Rs.5,000 ** (2659)

Supplying and fixing 3/8" dia: gate valve brass imported (Pegler or equivalent, approved quality).


S07- 239


Nos

Nos

Nos

Nos

Nos

NosGate valve brass for Max. 20 bars (Pegler 1068 or equivalent)

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Nos

NosFloat valve (Pegler 855 or equivalent)Supplying & fixing 1/2" dia. brass float valve with necessary fittings NosSupplying & fixing 3/4" dia. brass float valve with necessary fittings NosSupplying & fixing 1" dia. brass float valve with necessary fittings NosSupplying & fixing 1 1/4" dia. brass float valve with necessary fittings NosSupplying & fixing 1 1/2" dia. brass float valve with necessary fittings NosSupplying & fixing 2" dia. brass float valve with necessary fittings NosFoot valve BrassSupplying & fixing 1" dia. Copper foot valve with necessary fittings NosSupplying & fixing 1 1/2" dia. Copper foot valve with necessary fittings NosSupplying & fixing 2" dia. Copper foot valve with necessary fittings NosFoot valve PVC



Supplying and fixing 1" dia: gate valve brass imported (Pegler or equivalent, approved quality).

Supplying and fixing 1 1/4" dia: gate valve brass imported (Pegler or equivalent, approved quality).














S07- 240


Supplying & fixing 1" dia. PVC foot valve with necessary fittings (L/D or equivalent)Nos

Supplying & fixing 1 1/4" dia. PVC foot valve with necessary fittings (L/D or equivalent)Nos





Lavatory Basin

NosFixing Basin, Lavatory, existing brackets. (Tap, Waste trap and Basin available).

Nos

Nos

Nos

Nos

Nos

Removing bath room FittingsRemoving basin, sink or urinal including all fittings, and making walls good.

Nos

Nos

Nos

NosFixing bends, elbows, tees, crosses, G.I any size up to 2" (fittings available)

NosSupplying and fixing bends, G.I 1/2". NosSupplying and fixing bends, G.I 3/4". Nos

Fixing Lavatory Basin to wall, and connecting to existing water service and making good. (Basin, brackets and fittings available).

Supplying & fixing complete Basin, Lavatory, 22" x 16" with waste plug, new brackets, (tap, trap, and outlet pipe will be paid for separately)

Supplying & fixing complete Basin, Lavatory, 22" x 16" with waste plug, existing brackets, ( tap, trap, and outlet pipe will be paid for separately).

Prime cost of Basin and waste plug cuplins , 22" x 16" (Approved quality) Rs.2900 ) ** (1574)

Supplying & fixing complete Basin, Lavatory, 25" x 18" with waste plug, new brackets, ( tap, trap, and outlet pipe will be paid for separately)

Prime cost of Basin, Lavatory, 25" x 18" with waste plug, (Approved quality) Rs.3600 ) ** (1575)

Supplying & fixing complete Basin, Lavatory, 25" x 18" with waste plug, on existing brackets, ( tap, trap, and outlet pipe will be paid for separately).

Prime cost of Basin, Lavatory, 25" x 18" with waste plug, (Approved quality) Rs.3800 ) ** (1576)

Baths, C.I enamel, removing and re-fixing in New position and making good to walls and floors (Extra piping required will be paid for separately)

Fixing bath, enameled, C.I. any size, including trap, tap outlet, pipes etc. complete (Bath and fittings available).

supplying and fixing bath, enameled, 3" roll edge, C.I 5ft 6" including trap, tap etc. (out-let pipes will be paid for separately)


S07- 241


Supplying and fixing bends, G.I 1". NosSupplying and fixing bends, G.I 1 1/4". NosSupplying and fixing bends, G.I 1 1/2". NosSupplying and fixing bends, G.I 2". NosSupplying and fixing bends, G.I 3". Nos


S07- 242


Closet-pedestal type

Nos

NosSupplying & fixing ,pedestal closet (Indian make) ( seat and cover available)

Nos

NosPlastic seat cover, importedSupplying and fixing plastic seat cover, imported, approved quality. Nos

Nos

Nos

Nos

Nos

Fixing closet, pedestal type, available at site with cement concrete after breaking concrete floor, and making good and making connections to soil and flush pipes.

Closet, pedestal type, disconnecting and plugging sewer connection and making good all affected walls and floors.

Prime cost of pedestal closet with seat and cover (Indian make) is Rs.7,500 ** ( 1587)

Supplying & fixing closet, pedestal type, approved quality with low level glazed earthenware flushing cistern, flush pipe double plastic seat cover, 1/2" stop cock, trap etc. (Indian make)

Close coupled water closet suite (white) -ImportedSupplying & fixing, close coupled water closet suite, white, (4/2.6 Lit ) with water closet Pan, Cistern, Seat & Seat cover and trap etc.: complete (Twyford- Rearesh brand or equivalent approved quality).

Prime cost of close coupled water closet suite, (4/2.6 Lit ) with water closet Pan, Cistern, Seat & Seat cover and trap is Rs29,956 (Excluding 12% VAT ) (Refresh-Twyford or equivalent approved quality). ** (1846)

Supplying & fixing, close coupled water closet suite, white, (4/2.6 Lit ) with water closet Pan, Cistern, Seat & Seat cover and trap etc.: complete. (BECA-American standards)

Prime cost of close coupled water closet suite (BECA-American standards) is Rs.31,935 (Excluding 12% VAT ) ** (2646)

Close coupled water closet suite (white)-Manufactured in Sri Lanka.

Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite (white / Colour) with wash down 6/3 liter dual flushing. Has a horizontal outlet and cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: URBAN-D )

Prime cost of Close coupled water closet suite, white (Urban D-Rocell) is Rs.15,625 (Excluding 12% VAT ) ** (2647)

Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite(White/ Colour) with wash down 6/3 liter dual flushing. Has a horizontal outlet and cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: DUNE )

Prime cost of Close coupled water closet suite, white (Dune-Rocell) is Rs.18,598 (Excluding 12% VAT ) ** (2648)


S07- 243


Nos

Nos

Nos

Nos

Nos

Nos

Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: INTENCE )

Prime cost of Close coupled water closet suite, Coloured ( INTENCE-Rocell) is Rs.28,929 (Excluding 12% VAT ) ** (2649)

Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Elements Aqua )

Prime cost of Close coupled water closet suite, Coloured ( Elements Aqua-Rocell) is Rs.24,598 (Excluding 12% VAT ) ** (2826)

Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Aqua+ )

Prime cost of Close coupled water closet suite, Coloured ( Aqua+ -Rocell) is Rs.27,008 (Excluding 12% VAT ) ** (2649)

Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Summer Blue )

Prime cost of Close coupled water closet suite, Coloured ( Summer Blue -Rocell) is Rs.65,580 (Excluding 12% VAT ) ** (2649)

Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. In-Wall Tank Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Eternity )

Prime cost of Close coupled water closet suite, Coloured ( Eternity-Rocell) is Rs.57,678 (Excluding 12% VAT ) ** (2649)

Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. In-Wall Tank Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Urbanity )

Prime cost of Close coupled water closet suite, Coloured ( Urbanity-Rocell) is Rs.58,750 (Excluding 12% VAT ) ** (2649)


S07- 244


Nos

Nos

Close coupled water closet suite (colour)

Nos

Close coupled European type low level commode suit (white )

Nos Bidet, pedestal type-Imported

Nos

Bidet, pedestal type, Manufactured in Sri Lanka.

Nos

Nos

Bath wear set (3-Pieces)-Fixing Only

Nos

Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. In-Wall Tank Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Escape )

Prime cost of Close coupled water closet suite, Coloured ( Escape-Rocell) is Rs.58,214 (Excluding 12% VAT ) ** (2649)

Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: TT )

Prime cost of Close coupled water closet suite, Coloured ( TT-Rocell) is Rs.31,875 (Excluding 12% VAT ) ** (2649)

Supplying and fixing closed couple water closet suit (Coloured) with flushing cistern ,flush pipe, double plastic sheet cover ,stop cock, trap etc.(Twyford or equivalent approved quality)

Prime cost of Close coupled water closet suite, colour is Rs.45,000 (Excluding 12% VAT ) ** (2176)

Supplying and fixing close coupled European type low level commode suit white colour with 9 liter capacity which vitreous China low level cistern.(Twyford -Refresh brand)

Supplying & fixing bidet, pedestal type, with mixer taps and necessary specials, Twyford-Refresh brand or equivalent approved quality.

Prime cost of floor standing bidet in white colour (Twyford).Rs 44,645 (Excluding 12% VAT )** (1845)

Supplying & fixing Vitreous china floor standing bidet (white colour), Nominal size ( 22" x 14 1/2") floor to Rim height 16", complete with overflow hole, deck mounted single hole center set bidet faucet. (Dune-Rocell) Faucets not included

Prime cost of floor standing bidet in white colour (Dune-Rocell).Rs 9200 (Excluding 12% VAT ) ** (2655)

Supplying & fixing Vitreous china floor standing bidet (white colour), Nominal size (22"x151/2") floor to Rim height 16 1/2", complete with overflow hole, deck mounted single hole center set bidet faucet.(Urband D-Rocell) Faucets not included

Prime cost of floor standing bidet in white colour (Urband D-Rocell).Rs 9110 (Excluding 12% VAT ) ** (2656)

Fixing pedestal wash basin pedestal low level cistern & bidet with necessary specials & connecting to existing service line (Fittings are available.)


S07- 245


Closet-squatting typeSupplying & fixing closet, squatting type, with trap. (Indian) NosRemoving Closet-squatting typeRemoving closet, squatting type, plugging sewer connections and floor made good.

NosFixing available Closet-squatting type

Nos

Nos

NosSquatting pan- European

Nos

Nos

Squatting pan Ceramic ( Indian)Supplying & fixing squatting pan with foot rest Ceramic (Indian or equivalent)

Nos

Closet squatting type ( Indian or equivalent)

Nos

Cistern high level (Plastic)- ( Indian or equivalent)Supplying & fixing flushing cistern high level (Plastic). Nos

Cistern high level, ceramic-(Twyford or equivalent approved quality)

Nos

Cistern, high level, auto flush-CeramicNos

Cistern, high level, auto flush-Plastic

Nos

Fixing in cement concrete closet, squatting type, fixed, including breaking floor (closet available)

Fixing in cement concrete closet, squatting type, fixed including trap, including breaking floor (closet and trap available)

Fixing closet, squatting type, including flushing cistern and pipes complete. (Closet and all fittings available)

Supplying and fixing foot rest squatting pan and trap white to working order.(Twyford or equivalent approved quality)

Prime cost of Squatting pan (White) and trap is Rs. 17,500 ** ( 2165)

Supplying and fixing foot rest type squatting pan and trap colour to working order.(American standards)

Prime cost of (100 F) Squatting pan and trap (American standards) Rs. 15,940 ** ( 2179)

Prime cost of squatting pan with foot rest Ceramic Indian is Rs. 1700 ** (1875)

Supplying & fixing closet squatting type with trap complete with cistern plastic flush pipe etc.: Indian or equivalent (approved quality).

Prime cost of- squatting pan with foot rest Ceramic Indian is Rs. 1700 ** (1826) - plastic cistern Indian is Rs. 2450 ** (1827)

Prime cost of plastic cistern Indian is Rs. 2450 ** (1827)

Supplying and fixing ceramic high level cistern with fittings white ,complete.(Twyford or equivalent approved quality)

Prime cost of High level Cistern, ceramic is Rs.17,500 ** ( 2177)

Supplying & fixing high level ceramic automatic cisternPrime cost of High level automatic ceramic cistern is Rs. 6,600 ** ( 1895)

Supplying & fixing high level cistern plastic auto flush (2 gallons capacity) complete with flush pipe, sprinkler pipe, necessary fittings complete to working order.


S07- 246


Prime cost of High level auto flush plastic cistern is Rs.5,700 ** ( 1859)


S07- 247


Cistern low level, flushing- porcelain (Indian , approved quality).Supplying & fixing flushing cistern low level porcelain Coloured, (Indian , approved quality).

Nos

Syphon Supplying and fixing syphon for existing cistern (Indian) Nos

Supplying and fixing syphon for existing cistern (American Standard or Equivalent.)Nos

Magic BendSupplying and Magic bend 4" dia. For existing W.C. set etc. Nos

Urinal(Indian)Supplying & fixing urinal, wall type. Nos

Nos Urinal Imported- TwyfordSupplying and fixing bowl urinal white.(Twyford or equivalent approved quality)

Nos

Supplying and fixing bowl urinal colour.(Twyford or equivalent approved quality)Nos

Nos

Nos

Nos

Nos

Nos

Nos

Sink and fittings-Fixing OnlyFixing sink, any size, complete with waste plug, trap & brackets (sink and fittings available)

Nos

Prime cost of Flushing cistern low level porcelain Coloured (Indian , approved quality).Rs.2,850 ** ( 1881)

Prime cost of Syphon cistern (Indian).Rs.850 ** (2178)

Prime cost of Syphon cistern (American standerd-S.No:3343).Rs.1940 ** (2158)

Prime cost of Magic bend 4 dia. .Rs.650 ** (1904)

Prime cost of Urinal (wall type) .Rs.1625 ** (1720)Fixing available urinal, wall type.

Prime cost of Urinal (wall type, white) .Rs. 8,360 ** (2174)

Prime cost of Urinal (wall type, Colour) .Rs.9,500 ** (2175)Supplying and fixing (New wash brook) urinal.(American standards)Prime cost of New wash brook urinal.(American standards) .Rs.16,600 ** (2658)

Supplying & fixing Wall urinal with brackets.(American standards)Prime cost of wall urinal with brackets.(American standerds-412).Rs7,762 ** (2660)

Urinal - Manufactured in Sri Lanka.Supplying & fixing Wall urinal with Flush Valve.(Flo Point Urinal - Rocell)

Prime cost of wall urinal with brackets.Rs23,125* (2819)Supplying & fixing Wall urinal with Flush Valve.(Dew Point Urinal - Rocell)

Prime cost of wall urinal with brackets.Rs15,982* (2821)Supplying & fixing Wall urinal with Sensor.(Flo Point Urinal - Rocell)Prime cost of wall urinal with brackets.Rs34,732* (2820)Supplying & fixing Wall urinal with Sensor.(Dew Point Urinal - Rocell)

Prime cost of wall urinal with brackets.Rs29,375 (2822)


S07- 248


Sink

Nos

Nos

Nos

NosReplacing SinkRemoving & refixing sink or basin, in new position. Nos

NosStainless steel kitchen sink

Nos

Nos

Nos

Nos

Wash Basin

Nos

Supplying and fixing Wash Basin with pedestal 25"x18"white.(Twyford -Refresh Brand)Nos

Supplying & fixing sink, glazed, earthenware 30" x20"x8" with waste plug, brackets etc. complete.

Prime cost of Sink, glazed, earthenware 30" x20"x8" waste plug & chain.Rs.3,650 ** (1671)

Supplying & fixing sink, glazed, earthenware 30" x 18" x 8" with waste plug, on existing supports.

Prime cost of Sink, glazed, earthenware 30" x18"x8" waste plug & chain.Rs.3500 ** (1673)

Supplying & fixing sink, glazed earthenware 24" x 18" x 8" with waste plug, brackets etc., complete.

Supplying & fixing sink, glazed, earthenware 24" x 18" x 8" with waste plug, on existing supports.

Sink built in brick in cement 1:5 & cement rendered 1/2" (1:2), 2ft 0" x 2ft 0" with 6" high curb including making hole in wall and supplying & fixing 2" outlet pipe.

Supplying & fixing approved quality, stainless steel kitchen sink with single bowl & draining board with necessary waste plug, brackets etc.:

Prime cost of Stainless steel kitchen sink with single bowl & draining board.Rs.3000 ** (1835)

Supplying & fixing approved quality, stainless steel kitchen sink with double bowl & draining board with necessary waste plug, brackets etc.:

Prime cost of Stainless steel kitchen sink with double bowl & draining board.Rs.10,000 ** (1836)

Supplying & fixing 800X510mm stainless steel kitchen sink with single bowl & draining board with necessary waste plug, brackets etc.: (Teka or Equivalent)

Prime cost of Stainless steel kitchen sink with single bowl & draining board.Rs.17,277** (2810)

Supplying & fixing 1600X510mm stainless steel kitchen sink with double bowl & draining board with necessary waste plug, brackets etc.: (Teka or Equivalent)

Prime cost of Stainless steel kitchen sink with single bowl & draining board.Rs.35,135* (2811)

Supplying & fixing wash Basin 22"x16" white pedestal type with pillar tap, waste plug and other necessary fittings.(Indian approved quality)

Prime cost of Wash Basin 22"x16" white pedestal type (Indian or equivalent).Rs.5,355 (Excluding 12% VAT ) ** (1870)

Prime cost of wash basin 25"x18"(Twyford or equivalent approved quality).Rs18,755 (Excluding 12% VAT ) ** (2256)


S07- 249


Nos

Wash Basin (local Bath wear)

Nos

Nos

Nos

Nos

Nos

supplying and fixing Lavatory wash basin with pedestal 20"x18" (American Standerd-Kimera)

Prime cost of wash basin & pedestal (American Standard).Rs 21,735 (Excluding 12% VAT ) ** (2261)

Supplying & fixing Vitreous China floor standing wash basin (white colour) having nominal side of ( 23"x 18" ) with universal height pedestal of floor to Rim height 33", over flow hole and single tap hole in center, including pedestal, Wash basin fixing kit. (Urband D-Rocell) Cupling, Faucets, waste pipe, paid separately

Prime cost of Wash basin 23"x 18" ) with universal height pedestal (Urband D-Rocell). Rs 6,607 (Excluding 12% VAT ) ** (2651)

Supplying & fixing Vitreous China floor standing wash basin (white colour) having nominal side of (241/2"x 19") with universal height pedestal of floor to Rim height 32 1/2", over flow hole and single tap hole in center, including pedestal, Wash basin fixing kit. (Dune-Rocell) Cupling, pipe, paid separately

Prime cost of Wash basin (white colour) ( 24 1/2"x 19" ) with universal height pedestal (Dune-Rocell). Rs 8,009 (Excluding 12% VAT ) ** (2652)

Supplying & fixing Vitreous China floor standing wash basin (white colour) having nominal side of (241/2"x 19") with universal height pedestal of floor to Rim height 32 1/2", over flow hole and single tap hole in center, including pedestal, Wash basin fixing kit. (Intense-Rocell)

Cupling, pipe, paid separately

Prime cost of Wash basin (white colour) ( 24 1/2"x 19" ) with universal height pedestal (Intense-Rocell). Rs 15,670 (Excluding 12% VAT ) ** (2653)

Supplying & fixing Vitreous China floor standing wash basin (white colour) having nominal side of (241/2"x 19") with universal height pedestal of floor to Rim height 32 1/2", over flow hole and single tap hole in center, including pedestal, Wash basin fixing kit. (Elements Aqua-Rocell) Cupling, pipe, paid separately

Prime cost of Wash basin (white colour) ( 24 1/2"x 19" ) with universal height pedestal (Elements Aqua-Rocell). Rs 14,642 (Excluding 12% VAT ) ** (2823)

Supplying & fixing Vitreous China floor standing wash basin (white colour) having nominal side of (241/2"x 19") with universal height pedestal of floor to Rim height 32 1/2", over flow hole and single tap hole in center, including pedestal, Wash basin fixing kit. (Aqua+ -Rocell)


Prime cost of Wash basin (white colour) ( 24 1/2"x 19" ) with universal height pedestal (Aqua+ -Rocell). Rs 15,178 (Excluding 12% VAT ) ** (2825)


S07- 250


Nos

Nos

Nos

Nos

Corner wash basin (Imported quality)

Nos

Corner wash basin (Indian, approved quality)

Nos

Corner wash basin (local Bath wear)

Nos

Vanity basin

Nos

Supplying & fixing Vitreous China floor standing wash basin (white colour) wall mounted brackets, over flow hole and single tap hole in center, Wash basin fixing kit. (Summer Blue-Rocell) Cupling, pipe, paid separately

Prime cost of Wash basin (white colour) (Summer Blue-Rocell). Rs 30,803 (Excluding 12% VAT ) ** (2827)

Supplying & fixing Vitreous China floor standing wash basin (white colour) wall mounted brackets, over flow hole and single tap hole in center, Wash basin fixing kit. (Eternity-Rocell)


Prime cost of Wash basin (white colour) (Eternity-Rocell). Rs 14,285 (Excluding 12% VAT ) ** (2829)

Supplying & fixing Vitreous China floor standing wash basin (white colour) wall mounted brackets, over flow hole and single tap hole in center, Wash basin fixing kit. (Urbanity-Rocell) Cupling, pipe, paid separately

Prime cost of Wash basin (white colour) (Urbanity-Rocell). Rs 19,642 (Excluding 12% VAT ) ** (2831)

Supplying & fixing vitreous chaina wash basin 22"x15" Coloured with pedestal ( Equivalent to Rocell)

Prime cost of Wash basin 22"x15" Coloured with pedestal ( Equivalent to Rocell) .Rs 5,355 (Excluding 12% VAT ) ** (1870)

Supplying & fixing corner wash basin with one tap waste plug, new brackets etc.(Imported quality)

Prime cost of corner wash basin with one tap waste plug, new brackets. Rs 2,750 ** (1883)

Supplying & fixing corner wash basin with one tap, waste plug, new brackets etc.(Indian, approved quality)

Prime cost of corner wash basin with one tap, waste plug, new brackets etc.(Indian, approved quality) Rs 2,850 (Excluding 12% VAT ) ** (1885)

Supplying & fixing corner wash basin with one tap, waste plug, new brackets etc.(Aqua Corner - Rocell)

Prime cost of corner wash basin waste plug, new brackets etc.(Aqua Corner - Rocell) Rs 5,892 (Excluding 12% VAT ) ** (2835)

Supplying and fixing Vanity basin 25"x16" white.(Refresh-Twyford or equivalent approved quality)

Prime cost of Vanity Basin 25"x16"white.(Twyford or equivalent approved quality) Rs 15,000 (Excluding 12% VAT ) ** (2302)


S07- 251


Nos

Rubber plugsSupplying & fixing plugs, rubber 1" to 1 1/4" for wash basins and sinks. NosSupplying & fixing plugs, rubber 1 1/2" to 2" for wash basins and sinks. NosWooden plugs

NosBottle trapsSupplying & fixing 1 1/4" dia: plastic bottle trap (Indian or equivalent, approved quality).

Nos

Supplying & fixing 1 1/2" dia: plastic bottle trap (Indian or equivalent, approved quality).Nos

Supplying & fixing 2" dia: plastic bottle trap (Indian or equivalent, approved quality).Nos

Supplying & fixing 1 1/4" dia: bottle trap stainless steel approved quality. Nos

Supplying & fixing 1 1/2" dia: bottle trap stainless steel approved quality.Nos

PVC P-Trap (2" dia.)Nos

Fixing and Repairing , available TapsFixing cocks, brass any size, bib or push. (cock available) NosRemoving cocks, brass bib, push or stop cock, 1/2" to 1 1/2". NosRepairing cocks, bib or stop by fixing leather washers. NosRepairing cocks, self closing by fixing leather washer. NosBib Taps (Metallic)Supplying & fixing brass, bib taps, 1/2" (Chinese or equivalent, approved quality)

Nos

Supplying & fixing brass, chromium plated bib tap 1/2" . (Plumber or Equivalent.)Nos

Supplying and fixing Vanity basin 25"x16"colour.(Galerie-Twyford or equivalent approved quality)

Prime cost of Vanity Basin 25"x16"white.(Twyford or equivalent approved quality) Rs 17,500 (Excluding 12% VAT ) ** (2303)

Bedding in cement mortar 1:2, plugs, wooden, in (Group 6 category A) timber 4" long, tapered 3" to 2" square section, including making holes in walls, floor etc.

Prime cost of 1 1/4" dia: plastic bottle trap (Indian or equivalent, approved quality). Rs 350 ** (1854)

Prime cost of 1 1/2" dia: plastic bottle trap (Indian or equivalent, approved quality). Rs 400 ** (1855)

Prime cost of 2" dia: plastic bottle trap (Indian or equivalent, approved quality). Rs 700 ** (1856)

Prime cost of 1 1/4" dia: bottle trap stainless steel (Approved quality). Rs2,200 ** (1857)

Prime cost of 1 1/2" dia: bottle trap stainless steel (Approved quality). Rs. 2,400 ** (1858)

Supplying and fixing PVC, P-Trap (2" dia.)

Prime cost of bib tap, 1/2" dia: brass .(Chinese or equivalent, approved quality) Rs 550 ** (1592)


S07- 252


Supplying & fixing 1/2" dia. bib tap with long body chromium plated. (Approved quality)Nos

Supplying and fixing 1/2" dia: chromium plated bib tap imported (Duro) Nos

Bib Taps (Plastic)Supplying & fixing Plastic Bib Tap ½" dia. (T- Handle) (S-Lon or Equivalent.)

Nos

Supplying & fixing Plastic Bib Tap ½" dia. (Round- Handle)(S-Lon or Equivalent.) Nos

Supplying & fixing Plastic Bib Tap ¾" dia. (T- Handle) (S-Lon or Equivalent.) Nos

Supplying & fixing Plastic Bib Tap ¾" dia. (Round- Handle)(S-Lon or Equivalent.) Nos

Supplying & fixing Plastic long, Neck Bib Tap ½" dia. (T- Handle) (S-Lon or Equivalent.) Nos

Nos

Swan-Neck tap-(Metallic)Supplying & fixing chromium plated swan-neck tap ½" (Plumber) with necessary specials.

Nos

Swan-Neck tap-(Plastic)Supplying & fixing Plastic Swan- tap ½" dia. (T- Handle) (S-Lon or Equivalent.)

Nos

Supplying & fixing Plastic Swan-Neck tap ½" dia. (Round- Handle)(S-Lon or Equivalent.) Nos

Prime cost of, chromium plated bib tap 1/2" . (Plumber or Equivalent.) Rs1850 ** (1593)

Prime cost of 1/2" dia. bib tap with long body chromium plated.(Approved quality) Rs 2,100 ** (1876)

Prime cost of 1/2" dia: chromium plated bib tap imported.(Duro) Rs 2468 ** (1840)

Prime cost of bib tap, Plastic Bib Tap ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 161 ** (2532)

Prime cost of Plastic Bib Tap ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 211 ** (2533)

Prime cost of bib tap, Plastic Bib Tap ¾" dia. (T- Handle) (S-Lon or Equivalent.) Rs 239 ** (2534)

Prime cost of Plastic Bib Tap ¾" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 313 ** (2535)

Prime cost of bib tap, Plastic Bib Tap long Neck ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 227 ** (2536)

Supplying & fixing Plastic Bib Tap, long Neck ½" dia. (Round- Handle)(S-Lon or Equivalent.)

Prime cost of Plastic Bib Tap long Neck ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 259 ** (2537)

Prime cost of 1/2" dia: Chromium plated swan-neck tap ½" (Plumber) Rs 3360 ** (1829)

Prime cost of bib tap, Plastic Swan- tap ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 609 ** (2550)


S07- 253


Prime cost of Plastic Swan-Neck tap ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 850 ** (2551)


S07- 254


Chromium plated angle Taps/Valves 1/2"

Nos

Nos

Angle Taps/Valves (Plastic)Supplying & fixing Plastic Angle Tap ½" dia. (T- Handle) (S-Lon or Equivalent.)

Nos

Supplying & fixing Plastic Angle ½" dia. (Round- Handle)(S-Lon or Equivalent.) Nos

Chromium plated basin tap 1/2"Nos

Push tapsSupplying & fixing push taps 1/2" Brass, Becks, or equivalent approved quality.

NosSupplying & fixing push taps, 1/2" Brass, light pattern. NosStop tap. (Imported approved quality)

NosStop Taps (Plastic)

Nos

Nos

Nos

Nos

Supplying & fixing chromium plated angle tap 1/2" with necessary specials, imported, approved quality. (Duro or equivalent).

Prime cost of Chromium plated Angle valve(Duro) ½" dia. Rs 1840 ** (1830)

Supplying & fixing chromium plated angle tap 1/2" with necessary specials, imported, approved quality. (Indian or equivalent).

Prime cost of Chromium plated Angle valve(Plumber) ½" dia. Rs 1400 ** (1831)

Prime cost of bib tap, Plastic Angle ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 265 ** (2546)

Prime cost of Plastic Angle ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 253 ** (2547)

Supplying and fixing basin tap.(Twyford or equivalent approved quality)Prime cost of basin tap.(Twyford ) Rs 3500 ** (2171)

Supplying & fixing 1/2" dia. chromium plated stop tap. (Imported approved quality, concealed type)

Supplying & fixing Plastic Stop Taps ½" dia. (T- Handle) (S-Lon or Equivalent.)

Prime cost of bib tap, Plastic Stop Taps ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 159 ** (2540)

Supplying & fixing Plastic Stop Taps ½" dia. (Round- Handle)(S-Lon or Equivalent.)

Prime cost of Plastic Stop Taps ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 218 ** (2541)

Supplying & fixing Plastic Stop Taps ¾" dia. (T- Handle) (S-Lon or Equivalent.)

Prime cost of bib tap, Plastic Stop Taps ¾" dia. (T- Handle) (S-Lon or Equivalent.) Rs 309 ** (2542)

Supplying & fixing Plastic Stop Taps ¾" dia. (Round- Handle)(S-Lon or Equivalent.)

Prime cost of Plastic Stop Taps ¾" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 373 ** (2543)


S07- 255


Nos

Nos

Bath tub tapS/F 3/4" dia. bath tub tap chromium plated, imported approved quality. NosGarden Taps (brass)

NosGarden Taps (Plastic)Supplying & fixing Plastic Garden Tap ½" dia. (T- Handle) (S-Lon or Equivalent.)

Nos

Supplying & fixing Plastic Garden Tap ½" dia. (Round- Handle)(S-Lon or Equivalent.) Nos

Pillar cocksRepairing pillar cocks, fixing to Basin carefully without making any damage to Basin.

NosSupplying & fixing pillar cocks 1/2" Chromium plated, to basins. (Plumber or equivalent)

NosPillar tapsSupplying and fixing 1/2" dia: chromium plated Pillar tap. (American Standard or Equivalent.)

Nos

Supplying & fixing 3/4" Chromium plated pillar Cock, to baths. ,(Plumber or equivalent) Nos

Basin Piller Taps (Plastic)Supplying & fixing Plastic Basin Piller tap ½" dia. (Round- Handle)(S-Lon or Equivalent.)

Nos

Stop cockSupplying & fixing stop cock, brass 1/2" dia. NosSupplying & fixing stop cock, brass 3/4" dia. NosSupplying & fixing stop cock, brass 1" dia. NosSupplying & fixing stop cock, brass 1 1/4" dia. Nos

Supplying & fixing Plastic Stop Taps 1" dia. (T- Handle) (S-Lon or Equivalent.)

Prime cost of bib tap, Plastic Stop Taps 1" dia. (T- Handle) (S-Lon or Equivalent.) Rs 431 ** (2544)

Supplying & fixing Plastic Stop Taps 1" dia. (Round- Handle)(S-Lon or Equivalent.)

Prime cost of Plastic Stop Taps 1" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 498 ** (2545)

Supplying & fixing garden tap 1/2" dia: brass, heavy quality, with necessary specials, imported, approved quality.

Prime cost of bib tap, Plastic Garden Tap ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 218 ** (2538)

Prime cost of Plastic Garden Tap ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 253 ** (2539)

Prime cost of Chromium plated Pillar tap, 1/2" dia:. (American Standard) Rs. 2,856 ** (2664)

Prime cost of Chromium plated Pillar tap, 3/4" dia. (Plumber or equivalent) Rs.1,800 ** 1636

Prime cost of Plastic Basin Piller tap ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 479 ** (2548)


S07- 256


Supplying & fixing stop cock, brass 1 1/2" dia. NosSupplying & fixing stop cock, brass 2" dia. NosSupplying & fixing stop cock, chromium plated 1/2" dia . NosConnector, G.ISupplying and fixing connector G.I 1/2". NosSupplying and fixing connector, G.I 3/4". NosSupplying and fixing connector, G.I 1". NosSupplying and fixing connector G.I 1 1/4". NosSupplying and fixing connector G.I 1 1/2". NosSupplying and fixing connector G.I 2". NosSupplying and fixing connector G.I 3". NosFixing connector, any size up to 1 1/2" (Fixing only) NosFixing connector, above 1 1/2" and up to 3" (Fixing only) NosSupplying and fixing cover and seat for pedestal closets in Teak including polishing.

NosSupplying & fixing cover and seat for pedestal closets in plastic. NosElbow, G.ISupplying and fixing elbow, G.I 1/2". NosSupplying and fixing elbow G.I 3/4". NosSupplying and fixing elbow G.I 1". NosSupplying and fixing elbow G.I 1 1/4". NosSupplying and fixing elbow G.I 1 1/2". NosSupplying and fixing elbow G.I 2". NosCleaning flushing cistern C.I 2 gallons and painting one coat of anti-corrosive paint internally.

Nos

NosFixing flushing Cistern complete (cistern & brackets available) NosSupplying & fixing flushing Cistern, low level, porcelain ,approved quality complete.

Nos

Nos

Nos

NosFlush pipe of pedestal closets, re-joining with yarn and putty after removing old putty etc.

NosFlush pipe G.I fixing, including soldering joints, (Fixing only) NosFlush pipe, G.I supplying and fixing complete. NosHooks for pipesHooks for 1/2" pipes, supplying and fixing. NosHooks for 3/4" pipes, supplying and fixing. NosHooks for 1" pipes, supplying and fixing. NosHooks for 1 1/4" pipes, supplying and fixing. NosHooks for 1 1/2" pipes, supplying and fixing. Nos

Supplying & fixing flushing cistern, C.I 2 gallons, existing flush pipe and brackets etc. including ball valve.

Fitting in position in cistern flushing cistern lever forged out of wrought iron, 1" x 3/16" approx. 1ft 6" long bent to shape, drilled at both ends.

Flushing cistern, disconnecting and plugging water connection and making good all damage to wall floors etc.

Flushing cistern, removing and re-fixing in new position including necessary plugs, and making good to walls.


S07- 257


Hooks for pipes, available, fixing. NosJam NutsJam Nuts, G.I 1/2" supplying and fixing. NosJam Nuts, G.I 3/4" supplying and fixing. NosJam Nuts, G.I 1" supplying and fixing. NosJam Nuts, G.I 1 1/4" supplying and fixing. NosJam Nuts, G.I 1 1/2" supplying and fixing. NosJam Nuts, G.I 2" supplying and fixing. NosJam Nuts, any size up to 2" fixing (Jam Nut available). NosNipples, G.INipples, G.I 1/2" Supplying & fixing. NosNipples, G.I 3/4" Supplying & fixing NosNipples, G.I 1" Supplying & fixing. NosNipples, G.I 1 1/4" Supplying & fixing. NosNipples, G.I 1 1/2" Supplying & fixing. NosNipples, G.I 2" Supplying & fixing. NosNipples, any size up to 2" fixed. (Nipple available). NosPipes G.I

L.ft

L.ft

L.ft

L.ft

L.ft

L.ft

L.ft

L.ft

L.ft

L.ft

Pipes G.I 1/2" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls (pipe hooks to be paid for separately)

Pipes G.I 3/4" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls (pipe hooks to be paid for separately).

Pipes, G.I 1" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)

Pipes, G.I 1 1/4" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)

Pipes, G.I 1 1/2" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)

Pipes, G.I 2" supplying and fixing (fittings paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)

Pipes, G.I 2 1/2" supplying and fixing (fittings paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)

Pipes, G.I 3" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)

Pipes, G.I 1/2" to 2" fixing complete with specials such as bends, elbows etc. (pipes and specials available)

Pipes, G.I 2 1/2" to 3" fixing complete with specials such as bends, elbows etc. (pipes and specials available)


S07- 258


Pipes, G.I any size up to 2" removing and trench filling in. L.ftPipes, G.I 4" dia. removing, and walls floors etc. making good. L.ftPipes, G.I existing, taking out, cleaning and relaying, any size up to 2" including backfilling.

L.ftPipes, G.I 2 1/2" to 3" taking out, cleaning & relaying including backfilling.

L.ft

L.ftPipe joints, lead making good including soldering. Nos

L.ft

NosPlugs, G.I any size fixing (Plug available) NosPlugs, G.I 1/2" supplying and fixing. NosPlugs, G.I 3/4" supplying and fixing. NosPlugs, G.I 1" supplying and fixing. NosPlugs, G.I 1/4" supplying and fixing. NosPlugs, G.I 1 1/2" supplying and fixing. NosPlugs, G.I 2" supplying and fixing. NosSocket G.I Socket G.I 1/2" plain supplying & fixing. NosSocket, G.I 3/4" plain supplying and fixing. NosSocket, G.I 1" plain supplying and fixing. NosSocket, G.I 1 1/4" plain supplying and fixing. NosSocket, G.I 1 1/2" plain supplying and fixing. NosSocket, G.I 2" plain supplying and fixing. NosSocket, G.I 3" plain supplying and fixing. NosSocket, G.I reducing 3/4" to smaller sizes supplying and fixing. NosSocket, G.I reducing 1" to smaller size supplying and fixing. NosSocket, G.I reducing 1 1/4" to smaller sizes supplying and fixing. NosSocket, G.I reducing 1 1/2" to smaller sizes supplying and fixing. NosSocket G.I reducing 2" to smaller sizes, supplying and fixing. NosSockets G.I reducing 3" to smaller sizes supplying and fixing. NosSocket G.I any size fixing (socket available). Nos R.S.J 's as supports for tanks

cwtRemoving tank G.I

Nos

Pipes, G.I existing, any size up to 2" taking out, cleaning and relaying in new position, including backfilling.

Pipes, outlet, up to 8ft 0" cleaning, (removing & relaying where necessary will be paid for separately) assume 2ft 0" length

Pipes, underground, leaks repairing, including necessary trenching and backfilling (pipes or fittings to be used in repairs paid for separately)

Supplying & fixing in position steel work in R.S.J ' s as supports for tanks, up to 20' 0" height and painting 2 coats anti-corrosive paint.

Removing tank G.I, 25 to 200 gls. on existing supports up to 20' 0" height and connecting to existing pipes including disconnecting and taking down old tank and painting new tank 2 coats anticorrosive paint. (Tank available and scaffolding paid separately)


S07- 259


NosFixing tank, G.I

Nos

NosClearing & washing tankClearing & washing tank, storage, up to 400 gals capacity. NosCleaning & washing tank, storage, over 400 gals. Capacity. Nos

NosPlastishell (Single Layer) water tank

Nos

Nos

Nos

NosPlastishell (Triple Layer) water tank

Nos

Nos

Nos

Nos

Nos

Removing tank G.I. 250 to 400 gls. on existing supports up to 20' 0" height and connecting to existing pipes including disconnecting and taking down old tank and painting new tank 2 coats anticorrosive paint. (Tank available and scaffolding paid separately)

Fixing tank, G.I 25 - 250 gals. with overflow washout and stop cock, fixed on R.S joists and painted 2 coats of anticorrosive paint & connecting to supply and delivery pipes, (Tank fittings, pipes and R.S.J will be paid for separately).

fixing tank, G.I. 250 - 400 gals. with overflow washout and stop cock, fixed on R.S joists and painting 2 coats of anticorrosive paint connecting to supply and delivery pipes, (Tank fittings, pipes and R.S.J will be paid for separately).

Removing tank, storage, G.I and walls made good (scaffolding will be paid for separately where necessary).

Supplying and fixing Plastishell (Single Layer) water tank 250 liter capacity. ( fittings paid for separately ).




Supplying and fixing Plastishell (Triple Layer) water tank, 110 Gal. (500 lit.) capacity.( fittings paid for separately ).

Prime cost of Water tank 500lit. Plastishell (Triple Layer).Rs.10,680 ** (2482)

Supplying and fixing Plastishell (Triple Layer) water tank, 220 Gal. (1000 lit.) capacity. ( fittings paid for separately ).

Prime cost of Water tank 1000lit. Plastishell (Triple Layer).Rs.18,233 ** (2484)

Supplying and fixing Plastishell (Triple Layer) water tank, 440 Gal. (2000 lit.) capacity. ( fittings paid for separately ).

Prime cost of Water tank 2000 lit. Plastishell (Triple Layer).Rs.34,760 ** (2485)

Supplying and fixing Plastishell (Triple Layer) water tank, 1155 Gal. Or ( 5250 liter) capacity. ( fittings paid for separately ).

Prime cost of Water tank 5250 liter Plastishell (Triple Layer).Rs.68,250 ** (2486)

Supplying and fixing Plastishell (Triple Layer) water tank, 2310 Gal. or (10500 liter) capacity. ( fittings paid for separately ).


S07- 260


Floater switchSupplying and fixing floater switch with necessary fittings to over head water tank.

Nos

TeesTees, G.I 1/2" equal supplying and fixing. NosTees, G.I 3/4" equal supplying and fixing. NosTees, G.I 1" equal supplying and fixing. NosTees, G.I 1 1/4" equal supplying and fixing. NosTees, G.I 1 1/2" equal supplying and fixing. NosTees, G.I 2" equal, supplying and fixing. NosTrapsTrap, lead fixed in position with one wipe joint (Trap available). NosTrap lead, 1 1/4" supplying and fixing with one wipe joint. NosTrap lead 1 1/2" supplying and fixing with one wipe joint. NosTrap, lead 2" supplying and fixing with one wipe joint. NosTrap, lead 1" to 2" soldering and refixing. NosBath room accessories (Total Set)

Nos Tumbler holderSupplying & fixing tumbler holder, chromium plated, to wall with rawl plugs.

Nos

Soap tray/dishSupplying & fixing soap tray, white porcelain, to wall with rawl plugs. Nos

Supplying and fixing chromium plated soap tray. Nos

Supplying and fixing soap dish (American Standard or Equivalent.) Nos

Soap dispenser

Nos

Shelves, plate glass

Nos

Prime cost of Water tank 10,500lit. Plastishell (Triple Layer).Rs.120,225 ** (2487)

Prime cost of floater switch Rs.1500 ** (2205)

Supplying & fixing set of bath room accessories such as toilet paper holder, soap tray, tooth brush holder, towel bar and rings ,Bath room glass shelves etc. with necessary materials, Local and approved quality.

Prime cost of Tumbler holder, chromium plated, (Indian).Rs.800 ** (1716)

Prime cost of Soap tray, white porcelain,(Indian).Rs.500 ** (1689)

Prime cost of Chromium plated soap tray(American Standard).Rs.5096 ** (1838)

Prime cost of Soap dish (American Standard).Rs.2072 ** (2630)

Supplying & fixing soap dispenser (American Standard or Equivalent.), white porcelain, to wall with rawl plugs.

Prime cost of Soap dispenser (American Standard).Rs.4704 ** (2662)

Supplying & fixing shelves, plate glass 24" x 5" with chromium plated brackets to wall with Rawl Plugs.


S07- 261


Towel rail

Nos

Nos

Paper holder SEVA

Nos

Tooth brush holderSupplying & fixing tooth brush holder, Chromium plated to wall with rawl plugs.

Nos

Nos

Robe hook (SEVA)

Nos

Bath room mirror,

Nos

Nos

NosShower rose-Fixing OnlyFixing shower rose, any size (shower rose Paid separately). Nos

Prime cost of Shelves, plate glass 24" x 5" with chromium plated brackets.Rs.500 ** (1667)

Supplying & fixing chromium plated towel rail (Indian), 2ft 0" long and , ¾" dia. with necessary rawl plugs and screws.

Prime cost of chromium plated towel rail (Indian) , 2ft 0" long and , ¾" dia. Width.Rs.1,100 ** (1837)

Supplying & fixing chromium plated Towel rail (American Standard or Equivalent.-S. No:6588) , 2ft 0" long and , ¾" dia. with necessary rawl plugs and screws.

Prime cost of chromium plated Towel rail (American Standard)-(No:6588) , 2ft 0" long and , ¾" dia. Width. Rs .3,080 ** (2661)

Supplying & fixing SEVA paper holder (American Standard or Equivalent.) complete to working order.

Prime cost of SEVA paper holder (American Standard).Rs 2,408 ** (2628)

Prime cost of Tooth brush holder, Chromium plated(Indian).Rs 600 ** (1715)

Supplying & fixing tooth brush holder (American Standard or Equivalent.) complete to working order.

Prime cost of Tooth brush holder (American Standard)-(S.No:6582), Rs. 2 072 ** (2629)

Supplying & fixing SEVA Robe hook (American Standard or Equivalent.) complete to working order.

Prime cost of SEVA Robe hook (American Standard).Rs 1,792 ** (2631)

Supplying & fixing mirror, beveled, bath room type, oval shape, 20" x 16" Max. and min. dimensions, to wall with Rawl plugs and chromium plated fittings.

Prime cost of mirror, beveled, bath room type, oval shape, 20" x 16" -Rs 2,400 ** (1626)

Supplying & fixing 24" x 18", 5mm thickness beveled rectangular mirror, to wall with Rawl plugs, noton tape and chromium plated fittings.

Prime cost of mirror, beveled, bath room type, rectangular shape, 24" x 18", 5mm thickness -Rs 3,250 ** (1628)

Supplying and fixing toilet mirror cabinet with necessary rawl plugs and screws etc.( D 1003 s/s)


S07- 262


Shower roseSupplying & fixing Shower rose, 6" copper. NosSupplying & fixing shower Rose 7" chromium plated. NosSoldering and refixing shower Rose. NosSupplying & fixing PVC- 6" x 1/2" shower rose. NosPlastic Jet Shower roseSupplying & fixing Plastic Jet Shower Rose ½" dia. (S-Lon or Equivalent.)

Nos

NosSupplying & fixing Jet shower complete(American Standard or Equivalent.)

Prime cost of Jet shower imported (American Standard).Rs 2,016 ** (1873)


S07- 263


Shower headSupplying & fixing Shower head with arm. (American Standard) Nos

Bidet spray importedSupplying and fixing bidet spray imported Indian or equivalent. Nos

Supplying and fixing bidet spray imported (Grohe or equivalent ). Nos

AccessoriesSupplying & fixing chain, chromium plated, for bath or basin, with plug. NosSupplying & fixing chain pulls, chromium plated, for flushing cistern. NosFixing bends, elbows and tees- Workmanship onlyFixing bends, elbows and tees and other specials of P.V.C size 3".(Workmanship only).

NosBends P.V.CSupplying & fixing bends P.V.C 1/2". NosSupplying & fixing bends P.V.C 3/4". NosSupplying & fixing bends P.V.C 1". NosSupplying & fixing bends P.V.C 1 1/4". NosSupplying & fixing bends P.V.C 1 1/2". NosSupplying & fixing bends P.V.C 2". NosSupplying & fixing bends P.V.C 3". NosElbows P.V.CSupplying & fixing elbows P.V.C 1/2". NosSupplying & fixing elbows P.V.C 3/4". NosSupplying & fixing elbows P.V.C 1". NosSupplying & fixing elbows P.V.C 1 1/4". NosSupplying & fixing elbows P.V.C 1 1/2". NosSupplying & fixing elbows P.V.C 2". NosSupplying & fixing elbows P.V.C 3". NosReducing sockets & Tees P.V.CSupplying & fixing sockets reducing P.V.C (3/4"x1/2" ) to smaller sizes. NosSupplying & fixing sockets reducing P.V.C (1" x3/4") to smaller sizes. NosSupplying & fixing sockets reducing P.V.C (1 1/4"x1") to smaller sizes. NosSupplying & fixing sockets reducing P.V.C (1 1/2" x1 1/4") to smaller sizes.

NosSupplying & fixing sockets reducing P.V.C (2" x1") to smaller sizes. NosSupplying & fixing sockets reducing P.V.C (2" x1 1/2") to smaller sizes.

NosReducing Tees P.V.CSupplying & fixing tees reducing P.V.C (3/4"x1/2" ) to smaller sizes. NosSupplying & fixing tees reducing P.V.C (1" x3/4") to smaller sizes. NosSupplying & fixing tees reducing P.V.C (1 1/4"x1") to smaller sizes. NosSupplying & fixing tees reducing P.V.C (1 1/2" x1 1/4") to smaller sizes.

Nos

Prime cost of Shower head with arm (American Standard).Rs 2,200 ** (2663)

Prime cost of Bidet spray ( Indian) .Rs 1,500 ** (2057)

Prime cost of Bidet spray ( Grohe) .Rs 3,400 ** (2058)


S07- 264


Supplying & fixing tees reducing P.V.C (2" x1 1/2") to smaller sizes. NosSupplying & fixing tees reducing P.V.C (3" x 2") to smaller sizes. NosSupplying & fixing reducing tee P.V.C. ( 4" - 2") NosRepair Sockets & Tees P.V.CSupplying & fixing repair socket P.V.C 1/2". NosSupplying & fixing repair socket P.V.C 3/4". NosSupplying & fixing repair socket P.V.C 1". NosSupplying & fixing repair socket P.V.C 1 1/4". NosSupplying & fixing repair socket P.V.C 1 1/2". NosSupplying & fixing repair socket P.V.C 2". NosSupplying & fixing repair socket P.V.C 3". NosValve Socket P.V.CSupplying & fixing valve socket P.V.C 1/2". NosSupplying & fixing valve socket P.V.C 3/4". NosSupplying & fixing valve socket P.V.C 1". NosSupplying & fixing valve socket P.V.C 1 1/4". NosSupplying & fixing valve socket P.V.C 1 1/2". NosSupplying & fixing valve socket P.V.C 2". NosSupplying & fixing valve socket P.V.C 3". NosFaucet Socket P.V.CSupplying & fixing faucet sockets P.V.C 1/2". NosSupplying & fixing faucet sockets P.V.C 3/4". NosSupplying & fixing faucet sockets P.V.C 1". NosSupplying & fixing faucet sockets P.V.C 1 1/4". NosSupplying & fixing faucet sockets P.V.C 1 1/2". NosSupplying & fixing faucet sockets P.V.C 2". P NosSupplying & fixing faucet sockets P.V.C 3". NosTapered union without thread P.V.C Supplying & fixing tapered union without thread P.V.C 1/2". NosSupplying & fixing tapered union without thread P.V.C 3/4". NosSupplying & fixing tapered union without thread P.V.C 1". NosSupplying & fixing tapered union without thread P.V.C 1 1/4". NosSupplying & fixing tapered union without thread P.V.C 1 1/2". NosSupplying & fixing tapered union without thread P.V.C 2". NosSupplying & fixing tapered union without thread P.V.C 3". NosSupplying & fixing tapered union with thread for P.V.C and metal pipe connection 1/2".

NosSupplying & fixing tapered union 3/4" with thread for P.V.C & metal pipe connections.

NosSupplying & fixing tapered union 1" with thread for P.V.C & metal pipe connections.

NosSupplying & fixing tapered union 1 1/4" with thread for P.V.C & metal pipe connections.

NosSupplying & fixing tapered union 1 1/2" with thread for P.V.C & metal pipe connections.

Nos


S07- 265


Supplying & fixing tapered union 2" with thread for P.V.C & metal pipe connections. Nos

Supplying & fixing tapered union 3" with thread for P.V.C & metal pipe connections. Nos


S07- 266


Equal tees-P.V.CSupplying & fixing tees equal P.V.C 1/2". NosSupplying & fixing tees equal P.V.C 3/4". NosSupplying & fixing tees equal P.V.C 1". NosSupplying & fixing tees equal P.V.C 1 1/4". NosSupplying & fixing tees equal P.V.C 1 1/2". NosSupplying & fixing tees equal P.V.C 2". NosSupplying & fixing tees equal P.V.C 3". NosPlugs, sockets-P.V.CSupplying & fixing plugs P.V.C 1/2". NosSupplying & fixing plugs P.V.C 3/4". NosSupplying & fixing plugs P.V.C 1". NosSupplying & fixing plugs P.V.C 1 1/4". NosSupplying & fixing plugs P.V.C 1 1/2". NosSupplying & fixing Plugs P.V.C 2". NosSupplying & fixing plugs P.V.C 3". NosSupplying & fixing sockets plain P.V.C 1/2". NosSupplying & fixing sockets plain P.V.C 3/4". NosSupplying & fixing sockets plain P.V.C 1". NosSupplying & fixing sockets plain P.V.C 1 1/4". NosSupplying & fixing sockets plain P.V.C 1 1/2". NosSupplying & fixing sockets plain P.V.C 2". NosSupplying & fixing sockets plain P.V.C 3". NosPipes P.V.CSupplying & fixing pipes P.V.C, 1/2" dia.(Type 1000)- PE.(Fittings paid separately).

L.ftSupplying & fixing pipes P.V.C, 3/4"dia.(Type 1000)- PE (Fittings paid separately).

L.ftSupplying & fixing pipes P.V.C, 1"dia. (Type 1000)- PE(Fittings paid separately).

L.ftSupplying & fixing pipes P.V.C, 1 1/4"dia. (Type 1000)- PE(Fittings paid separately).

L.ftSupplying & fixing pipes P.V.C 1 1/2"dia. (Type 1000)- PE (Fittings paid separately).

L.ftSupplying & fixing pipes P.V.C, 2"dia. (Type 1000)- PE (Fittings paid separately).

L.ftSupplying & fixing pipes P.V.C 3". (Type 1000)- PE (Fittings paid separately).

L.ftFixing pipesFixing pipes P.V.C, 1/2" to 2" dia. Complete with specials. (pipes & specials paid separately).

L.ftFixing pipes P.V.C, 2 1/2" to 3"dia. complete with specials. (pipes & specials paid separately).

L.ft

NosForming bends or jointing pipes by heating without fixing specials in rigid P.V.C, 1/2" to 1"dia. (Workmanship only).


S07- 267


Nos

NosPipes P.V.C (25% pipe cost included for Specials)

L.ft

L.ft

L.ft

L.ft

L.ft

L.ftFlexible cord (S--Lon or Equivalent))Supplying and fixing flexible cord -12" (S-lon or equivalent) NosSupplying and fixing flexible cord -18" (S-lon or equivalent) NosSupplying and fixing flexible cord -24" (S-lon or equivalent) NosSupplying and fixing flexible cord -48" (S-lon or equivalent) NosSupplying and fixing flexible cord -60" (S-lon or equivalent) NosFlexible cord (Imported European)Supplying and fixing flexible cord 1ft -6" imported, approved quality. (Italy or equivalent).

NosSupplying and fixing flexible cord 1ft -0" imported, approved quality. (Italy or equivalent).

NosFlexible hoseSupplying and fixing 1/2" dia: Flexible hose (American Standard or Equivalent.)

Nos

Garden Watering Hose ½" dia.Supplying Garden Hose ½" dia. & 15m long (S-Lon or equivalent). NosSupplying Garden Hose ½" dia. & 30m long (S-Lon or equivalent). NosWater pump

Nos

NosSupplying and installation of "Jinasena" 1/2" dia. Water pressure pump Nos

Supplying and fixing 1" dia. pressure pump 110/A 18/1 (Centric type pumping unit)Nos

Forming bends or jointing pipes by heating without fixing specials in rigid P.V.C 1 1/4" to 2" dia.(Workmanship only).

Forming bends or jointing pipes by heating without fixing specials in rigid P.V.C, 2 1/2" to 3"dia. (Workmanship only).

Supplying & fixing pipes P.V.C, 1/2" dia. (Type 1000) including specials. (25% pipe cost included for Specials)

Supplying & fixing pipes P.V.C, 3/4"dia. (Type 1000) including specials. (25% pipe cost included for Specials)

Supplying & fixing pipes P.V.C, 1"dia. (Type 1000) including specials. (25% pipe cost included for Specials)

Supplying & fixing pipes P.V.C, 1 1/4"dia. (Type 1000) including specials. (25% pipe cost included for Specials)

Supplying & fixing pipes P.V.C, 1 1/2"dia. (Type 1000) including specials. (25% pipe cost included for Specials)

Supplying & fixing pipes P.V.C, 2"dia. (Type 1000) including specials. (25% pipe cost included for Specials)

Prime cost of Flexible hose (American Standard) Rs. 448 ** (2666)

Installing available 3/4"-1" water pump with necessary fittings, foot valve, concrete base, rag bolts etc.(concrete paid for separately)

Installing available 1 1/2"-2" dia. water pump with necessary fittings, concrete base and rag bolts.(concrete paid for separately).

Prime cost of Pressure pump (Br - 50) ,Jinasena" 1/2" dia. Rs.18,370 ** (2577)


S07- 268


Electric water geyserReplacing available Electric water Geyser , making hot water Supply in order.

Nos

Nos

Nos

Nos

Nos

Nos

Plastic gullySupplying & fixing plastic gully grating 6"x6". Nos

NosShower tray fiberglassSupplying & fixing shower tray fiberglass 30" x 32" including waste plug & specials

Nos

Elbows for down pipe. Supplying & fixing or replacing, only a 3 1/2" P.V.C. elbows for down pipe.

NosRunning head. Supplying & fixing or replacing, only a P.V.C. running head. NosGutter end.Supplying & fixing or replacing, only a square type P.V.C. gutter ends. NosGutter Joint.Supplying & fixing or replacing, only a square type P.V.C. gutter joints. NosEves gutters (PVC)-Square type

L.ft

Prime cost of 1" dia. Centric pressure pump 110/A 18/1 ,Jinasena- 1" dia. Rs.34,532 ** (2576)

Supplying and fixing 50 Liter Electric water Geyser ( approved quality) on a wall or existing brackets and connected to the hot water supply system.(hot water piping system paid separately)

Prime cost of 50 Liter Electric water Geyser ( approved quality).Rs 24,500 ** (2574)

Supplying and replacing of Electric water geezer (water heater 30 lit.) imported quality. (Ariston or equivalent)

Prime cost of 30 Liter Electric water Geyser ( approved quality).Rs 22,500 ** (2575)

Supplying and fixing of instant water geezer (water booster pump) imported quality. (Singer or equivalent)

Prime cost of instant water Geyser ( approved quality).Rs 14,999 ** (2807)





Providing Catch pit 6"x6"x3" in cement mortar.

Prime cost of fiberglass shower tray 30" x 32" .Rs 7,000 ** (1887)

Supplying and fixing eves gutters square type PVC with necessary specials, including running heads, miter joints, gutter joints, gutter brackets, gutter ends etc.


S07- 269


Supplying & fixing eave gutters 6" half-round P.V.C with P.V.C brackets. L.ft

Down pipes 3½" dia. P.V.C

L.ftSupplying & fixing rain water down pipes 3 ½" dia. P.V.C to wall, with necessary specials, including elbows, sockets, clips etc.


S07- 270


R-DRAIN LAYERInterceptor, EarthenwareInterceptor, earthenware, 4" supplying and fixing. NosInterceptor, earthenware, 6" supplying and fixing. NosInterceptor, earthenware, 4" supplying and fixing. (Fixing only). NosManhole- brick in cement

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Manhole 2ft x 2ft and up to 2ft 0" deep, 9" thick brick in cement 1:3 walls and cement rendering 1/2" (1:2) with 6" cement concrete foundation 1:3:6(2" metal) including forming channels, but without cover.

Manhole 3ft 6" x 2ft 3" and 2ft 0" to 4ft 0" deep 9" thick brick in cement 1:3 walls and cement rendering 1/2" (1:2) with 6" cement concrete foundation 1:3:6(2" metal) including forming channels, but without cover.

Manhole 3ft 6" x 2ft 3" and 4ft 0" to 6ft 0" deep, 9" thick brick in cement 1:3 walls and cement rendering 1/2" (1:2) with 6" cement concrete foundation 1:3:6 (2" metal) including forming channels, but without cover.

RCC Manhole (Type A)- [As per Drg.No 2013-TP-ST06 & ST07]RCC Manhole type A, Internal dimensions 475 x 625mm (depth up to 450mm) wall thickness 150mm & base Slab thickness 150mm. (Cover Slab & Inlet / Outlet Connections Paid for Separately) Single R/F

RCC Manhole type A, Internal dimensions 475 x 625mm (Depth is greater than 450mm & up to 600mm) wall thickness 187.5 mm & base Slab thickness 175 mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F

RCC Manhole type , Internal dimensions A- 475 x 625mm (Depth is greater than600mm & upto750 mm) wall thickness 187.5mm & base Slab thickness 175 mm. (Cover Slab & Inlet / Outlet Connections Paid for Separately) Double R/F

RCC Manhole type A, Internal dimensions 475 x 625mm (Depth is greater than 750mm & up to 900mm) wall thickness 187.5mm & base Slab thickness 175mm. (Cover Slab & Inlet / Outlet Connections Paid for Separately) Double R/F

RCC Manhole (Type B)- [As per Drg.No 2013-TP-ST06]RCC Manhole type B ,Internal dimensions 475 x 750mm (depth up to 450mm)wall thickness 150 mm & base Slab thickness 150 mm.(Cover Slab & Inlet / Outlet Connections Paid Separately) Single R/F

RCC Manhole type B - 475 x 750mm internally (Depth is greater than 450mm & up to 600mm) wall thickness 175 mm & base Slab thickness 175mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F

RCC Manhole type B- 475 x 750mm internally (Depth is greater than600mm & upto750 mm) wall thickness 175 mm & base Slab thickness 175mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F


S07- 271


Nos

RCC Manhole type B, Internal dimensions 475 x 750mm internally (Depth is greater than 750mm & up to 900mm) wall thickness 175 mm & base Slab thickness 175mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F


S07- 272


Nos

Nos

Nos

NosManhole cover, reinforced concrete

NosManhole cover, Cast IronManhole cover C.I rectangular, above 1 cwt. supplying and fixing. Nos

NosCast iron grating

NosWire dome (Steel)Wire domes for 2" pipes supplying and fixing. NosWire domes for 4" pipes supplying and fixing. NosWire dome (Copper)Supplying & fixing copper wire dome for 2" dia. P.V.C drainage pipes. NosSupplying & fixing copper wire dome for 4" dia. P.V.C drainage pipes. NosDrainage Fittings 4" (110mm) dia-(Local make)Supplying & fixing 4" dia. P.V.C plain socket (Local make) Nos

NosSupplying & fixing 4" dia. P.V.C drainage bend 45 degree. (S-Lon or Equivalent.)

Nos


Nos

NosSupplying & fixing 4" dia. P.V.C drainage Tee. (S-Lon or Equivalent.) Nos

RCC Manhole (Type C)- [As per Drg.No 2013-TP-ST06]RCC Manhole type C- 475 x1050mm internally (Depth up to 450mm) wall thickness 100 mm & base Slab thickness 150 mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Single R/F

RCC Manhole type C , Internal dimensions 475 x1050mm (Depth is greater than 450mm & up to 600mm) wall thickness 175 mm & base Slab thickness 175 mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F

RCC Manhole type C, Internal dimensions 475 x1050mm internally(Depth is greater than600mm & upto750 mm) wall thickness 175 mm & base Slab thickness 175mm.. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F

RCC Manhole type C , Internal dimensions 475 x1050mm (Depth is greater than 750mm & up to 900mm) wall thickness 175 mm & base Slab thickness 175mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F

Manhole cover, reinforced concrete 3" thick 2ft 0" x 2ft 0" approx. supplying and fixing, reinforced with 1/4" dia. M.S. rods at 3" centers, both ways.

Manhole cover Ductile iron rectangular 2'X2', supplying and fixing. (heavy duty) 12.5 TON (Prime cost Rs.17,000)

Grating C.I, 6" x 6" supplying and fixing.

Supplying & fixing 4" dia. P.V.C drainage elbow with single Door, approved quality with rubber ring joint.(Locally made)

Supplying & fixing 4" dia. P.V.C drainage bend 45 degree ,with single Door (S-Lon or Equivalent.)

Supplying & fixing 4" dia. P.V.C drainage bend 89 degree. With single Door (S-Lon or Equivalent.)


S07- 273


Supplying & fixing 4" dia. P.V.C drainage Swept Tee. (S-Lon or Equivalent.)Nos

Supplying & fixing 4" dia. P.V.C drainage Tee. with single Door (S-Lon or Equivalent.)Nos

Supplying & fixing 4" dia. P.V.C drainage Swept Tee. with single Door (S-Lon or Equivalent.)Nos

Supplying & fixing 4" dia. P.V.C drainage "Y" junction (S-Lon or Equivalent.)Nos

NosDrainage Fittings 2" (63mm) dia.Supplying & fixing 2" dia. P.V.C drainage bend 45 degree. (S-Lon or Equivalent.)

Nos


Nos

NosSupplying & fixing 2" dia. P.V.C drainage Tee. (S-Lon or Equivalent.) NosSupplying & fixing 2" dia. P.V.C drainage Swept Tee. (S-Lon or Equivalent.)

NosSupplying & fixing 4" dia. P.V.C drainage Tee. with single Door (S-Lon or Equivalent.)

NosSupplying & fixing 2" dia. P.V.C drainage Swept Tee. with single Door (S-Lon or Equivalent.)

NosSupplying & fixing 2" dia. P.V.C drainage "Y" junction (S-Lon or Equivalent.)

Nos

NosDrainage Fittings 1½"or (50mm) diaSupplying & fixing 1½" dia. P.V.C drainage bend 45 degree. (S-Lon or Equivalent.)

Nos

NosSupplying & fixing 1½"" dia. P.V.C drainage bend 89 degree. (S-Lon or Equivalent.)

Nos

NosSupplying & fixing 1½"" dia. P.V.C drainage Tee. (S-Lon or Equivalent.)

NosSupplying & fixing 1½"" dia. P.V.C drainage Swept Tee. (S-Lon or Equivalent.)

NosSupplying & fixing 1½"" dia. P.V.C drainage Tee. with single Door (S-Lon or Equivalent.)

Nos

Supplying & fixing 4" dia. P.V.C drainage "Y" junction with single Door (S-Lon or Equivalent.)

Supplying & fixing 2" dia. P.V.C drainage bend 45 degree, with single Door (S-Lon or Equivalent.)

Supplying & fixing 2" dia. P.V.C drainage bend 89 degree, with single Door (S-Lon or Equivalent.)

Supplying & fixing 2" dia. P.V.C drainage "Y" junction with single Door (S-Lon or Equivalent.)

Supplying & fixing 1½" dia. P.V.C drainage bend 45 degree with single Door (S-Lon or Equivalent.)

Supplying & fixing 1½"" dia. P.V.C drainage bend 89 degree, with single Door (S-Lon or Equivalent.)


S07- 274


NosSupplying & fixing 1½" dia. P.V.C drainage "Y" junction (S-Lon or Equivalent.)

Nos

NosPipes P.V.C, 4"(110mm) dia, (type 250)-(Vent pipes fixed to walls)

L.ftPipes P.V.C, 4"(110mm)dia, (type 400)-(Vent pipes fixed to walls)

L.ftPipes P.V.C, 4"(110mm) dia, (type 400)- lay in Trenches

L.ft

L.ft

L.ftDrain Pipes P.V.C, 4" dia, (type 600)- lay in Trenches

L.ft

L.ft

L.ftDrain Pipes P.V.C, 6" dia, (type 600)- lay in Trenches

L.ft

L.ft

L.ftDrain Pipes P.V.C, 12" dia, (type 600)

Supplying & fixing 1½"" dia. P.V.C drainage Swept Tee. with single Door (S-Lon or Equivalent.)

Supplying & fixing 1½" dia. P.V.C drainage "Y" junction with single Door (S-Lon or Equivalent.)

Supplying & fixing 4" dia. (type 250) P.V.C pipes as vent pipes fixed to walls with necessary wooden plugs and P.V.C saddles at 4ft centers.

Supplying & fixing 4" dia. (type 400) P.V.C pipes, as drainage pipes fixed to walls with necessary wooden plugs, brass screws & saddles at 4ft centers.

Pipes P.V.C, 4" dia, (type 400) laying on cement concrete 6" thick up to 2ft 0" depth of invert including excavation and cement concrete hunching (1:3:6(1")).

Pipes P.V.C, 4" dia, (type 400) laying on cement concrete 6" thick over 2 ft. up to 4 ft. depth of invert including excavation and cement concrete hunching (1:3:6(1")).

Drains P.V.C, 4" dia, (type 400) laying on cement concrete 6" thick over 4ft -0" up to 6ft -0" depth of invert including excavation and cement concrete hunching (1:3:6(1")).

Drains, P.V.C, 4" dia: (type 600) laying on cement concrete 6" thick up to 2ft 0" depth of invert including excavation, back filling and cement concrete hunching 1:3:6(1").

Drains P.V.C, 4" dia. (type 600) laying on cement concrete 6" thick over 2 ft. up to 4 ft. depth of invert including excavation back filling and cement concrete hunching 1:3:6(1").

Drains P.V.C, 4" dia. (type 600) laying on cement concrete 6" thick over 4 ft. up to 6 ft. depth of invert including excavation back filling and cement concrete hunching 1:3:6(1").

Drains PVC, 6" dia. (type 600) laying on cement concrete 6" thick up to 2ft. depth of invert including excavation , backfilling and cement concrete hunching 1:3:6 (1").

Drains PVC, 6" dia.( type 600 ) laying on cement concrete 6" thick over 2ft. up to 4ft. depth of invert including excavation backfilling and cement concrete hunching 1:3:6 (1" ).

Drains PVC, 6" dia.( type 600 ) laying on cement concrete 6" thick 4ft. up to 6ft. depth of invert including excavation backfilling and cement concrete hunching 1:3:6 (1") .


S07- 275


L.ft

Drains PVC, 12" dia.( type 600 ) laying on cement concrete 6" thick over 2ft. up to 4ft. depth of invert including excavation backfilling and cement concrete hunching 1:3:6 (1" ).


S07- 276


S-MISCELLANEOUS

L.ft

L.ftBamboo supplying only at site. L.ftBamboo supplying and fixing in position. L.ftBamboos removing and refixing with coir strings. L.ft Scaffolding of Bamboos

Nos

NosSteel scaffolding SetsHiring a steel scaffolding set per day at site. NosLabour for handling, Erecting & dismantling a steel scaffolding set . (up to 30' feet height )

NosGarden lamp

NosFencingNote: Refer Item numbers From J080 to JO82 for chain-link fencing

L.ft

L.ft

L.ft

L.ft

L.ftFence barbed wire fixing with G.I staples on existing timber posts (Barbed wire available).

L.ft

L.ft

Bamboo barricade 3ft 0" high composing of whole bamboos with one horizontal runner and uprights 6ft 0" apart, supplying and fixing and removing as and when required, (Salvaged materials to be contractor s property)

Bamboo barricade 4ft 0" high with 2 horizontal runners and uprights 6ft 0" apart, supplying and fixing and removing as and when required, (Salvaged materials to be contractor s property).

Erecting scaffolding of Bamboos and planks for lifting or lowering of storage tanks to a height of 15ft to 30ft and removing same after completion of work (salvaged materials to be contractor's property).

Erecting scaffolding of Bamboos and planks for lifting or lowering of storage tanks to a height of 30ft to 50ft and removing same after completion of work (salvaged materials to be contractor s property).

Supplying and fixing garden lamp (Mushroom type)

Fence, G.I barbed wire( gauge 14), four needles per each node & 4" apart with three curls of wire, supplying & fixing on existing timber posts with G.I staples. (Min Tensile Strength of B.wire 310 N/mm2)

Fence, G.I barbed wire( gauge 14), four needles per each node & 4" apart with three curls of wire, supplying & fixing on existing concrete posts with available hook bolts. (Min Tensile Strength of B.wire 310 N/mm2)

Fence, G.I barbed wire( gauge 14), four needles per each node & 4" apart with three curls of wire, supplying & fixing in renewing short lengths on timber posts. (Min Tensile Strength of B.wire 310 N/mm2)

Fence, G.I barbed wire( gauge 14), four needles per each node & 4" apart with three curls of wire, supplying & fixing on concrete posts with available hook bolts, (Min Tensile Strength of B.wire 310 N/mm2)

Fence, PVC coated barbed wire, four needles per each node & 3" apart with three curls of wire, supplying & fixing on concrete posts with available hook bolts.

Fixing barbed wire fence with G.I staples on concrete posts with available hook bolts.(barbed wire available).


S07- 277


Fence, barbed wire, straining only and refixing with staples, (barbed wire available)L.ft

Fence, barbed wire, straining only and refixing on concrete posts with available hook bolts. L.ft

L.ft

Nos

Nos

Nos

L.ftNos

L.ftWell, bailing out water

L.ft

L.ftWell, bailing out water, 8ft -10ft dia. and 20ft -30ft depth. say 5ft 0" depth of water

L.ftDewatering from excavated foundation pits or Trenches using submersible pump.

DayWater proofing (Treatment)

sq.ft

sq.ftWater proofing (Membrane)

sq.ftTimber treatment

Fence posts or struts, Milla, Na, Palu or Satin 4" to 6" average dia. supplying and fixing in ground complete, inclusive of sharpening and tarring.

Intermediate fence posts or struts, cement concrete 1:1 1/2: 3 (3/4") reinforced with 4 Nos. 1/4" dia. M.S rods, 5ft 7" high square section 4" to 6" supplying and fixing complete as per drawing No. 68 of 22.07.1936.

Intermediate fence posts or structs, cement concrete 1:1 1/2: 3 (3/4") reinforced with 4 Nos. 1/4" dia. M.S rods, 7ft 6" high square section 4" to 6" supplying and fixing complete as per drawing No. 68 of 22.07.1936.

End post and strut for Type barbed wire fence supplying and fixing complete in cement concrete as per drawing No: 68 of 1936.

Fence, bared wire, 5 strands, 12 1/2 B.W.G with 4 points at 3" centers and R.C. posts (1:2:4) 3/4" metal, reinforced with 4 Nos. 1/4" rods with No. 14 B.W.G stirrups at 8" centers. Post to be fixed at 8ft 0" centers including excavation, cement concrete

Straining Bolts, 18" long 1/2" dia. making and fixing (approx.). Stoneware pipes, 4" dia, over fume cupboards, supplying and fixing along wall with iron brackets and plugs.

Well, bailing out water, 5ft -7" dia. up to 20ft depth including cleaning well. say 5ft 0" depth of water

Well, bailing out water, 5ft -7" dia. up to 21ft to 30ft depth including cleaning well. say 5ft 0" depth of water

Waterproofing treatment using "Xypex" or equivalent approved product including preparation of surface according to Manufacturer s Specifications.

Waterproofing treatment using "Thoroseal" or equivalent approved product including preparation of surface, according to Manufacturer s Specifications.

Supply & Laying 1000 gauge Polythene membrane.


S07- 278


cu.ft

Structural Timber treated by Vacuum Pressure Impregnation Technique with approved wood preservatives such as CCB that are registered by register of pesticides, for protection against wood destroying agents such as wood bores, fungi and termites. (Execution according to the Manufacturers specifications) (By "Finlay Celurised treated " or equivalent system) Rate per Cubic Foot = Rs. 311.61/- inc Vat


S07- 279


Door PVC

sq.ft

sq.ft

L.ftLandscaping

Laying turf sods

sq.ftLocal fruit treesSupply and planting Mango tree ( about 4' tall ) NosSupply and planting Guava tree ( about 4' tall ) NosSupply and planting Jambu tree ( about 4' tall ) NosSupply and planting Anoda tree ( about 4' tall ) NosSupply and planting Naminan tree ( about 4' tall ) NosSupply and planting Asoka tree ( about 4' tall ) NosSupply and planting Bamboo tree ( about 4' tall ) NosPalm trees

NosNosNosNosNosNos

Mixed FlowerNosNosNosNosNosNos

Road Construction

Cube

Cube

Cube

CubeSpreading ,watering & rolling 4" aggregate including hire charges of roller.

Cube

Door PVC supply and fixing to existing opening, (with out frame), Lock, complete with altered size with out preparing reveals. (Size 2' 6" x 6' 9")

Door PVC supply and fixing to existing opening, with frame, Lock, complete with altered size with out preparing reveals. (Size 2' 6" x 6' 9")

Supplying and fixing PVC step nosing to stairway step edges using approved adhesive.

Supplying & laying turf sods of approved type including bedding material, pegging and watering.

Supply and planting Fox tail tree. ( about 5' tall ) Supply and planting Ceiling Wax tree. ( about 5' tall ) Supply and planting Raffic tree. ( about 5' tall ) Supply and planting Kentia tree. ( about 5' tall ) Supply and planting Cane tree. ( about 5' tall ) Supply and planting Royal palm tree. ( about 5' tall )

Supply and planting Cannas plant. Supply and planting Idda plant. Supply and planting Exoria Medium plant. Supply and planting Royal Exoria plant. Supply and planting Hibiscus plant. Supply and planting Bougainville plant (about 2' tall)

Supplying and pilling approved 4" aggregate for road construction, at site excluding hire charges.

Supplying and pilling approved 1 1/2" aggregate for road construction, at site excluding hire charges.

Supplying and pilling approved 3/4" aggregate for road construction, at site excluding hire charges.

Supplying and pilling approved 1/2" aggregate for road construction, at site excluding hire charges.


S07- 280


Spreading ,watering & rolling 2"- 3/4" aggregate including hire charges of roller.Cube

Sqr

Sqr

Sqr

SqrProviding Labour Services Providing Labour services in Un Skilled trades of any type of manual work on day work basis.

DayProviding Labour services in semi Skilled trades, on day work basis. Day

Day

DayFlaggingCords, woven, or picture, supplied and fixed. L.ftCords, flag, 1/4" dia. supplied and fixed. L.ftCords, flag mast, 3/8" dia. supplied and fixed. L.ftCords, flag mast, 1/2" dia. supplied and fixed. L.ft

Nos

Nos

NosFlagpoles (available) planted as directed removed when required, and ground made good.

Nos

Bitumen(80/100) surfacing first coat using 2Ltr/Sq.m including blinding with sand at the rate of 125 Sq.m/Cu.m.

Bitumen(80/100) surfacing 2 nd subsequent coat using 1 Ltr/Sq.m including blinding at the rate of 125 Sq.m/Cu.m

Emulsion /Cold bitumen (CRS-1) surface treatment 1st coat with 3.5 Ltr/Sq.m including blinding with sand,@125 Sq.m/Cu.m(Manual)

Emulsion /Cold bitumen (CRS-1) surface treatment subsequent coat using 0.075 Ltr/Sq.m including blinding with sand,@125 Sq.m/Cu.m(Manual)

Providing Labour services in Skilled trades such as Mason, Carpenter, Bar bender ,Painter, polisher, Plumber, Simple Machines operator etc. on day work basis.

Providing Labour services in Skilled trades such as Fitter, Electrician, Welder, Tiller, Glazier, Tinker, Mechanic, Aluminium fabricator, Heavy equipment operator, Sign board Painter etc. on day work basis.

Flags, average size 6ft x 3ft hung up on buildings as directed and removed when required. (Flags available - any poles used are to be paid for separately)

Flags, small (Burges) hung up on buildings as directed and removed when required. (Flags available - any poles used are to be paid for separately) (up to 100)

Flags, small (Burges) hung up on buildings as directed and removed when required. (Flags available - any poles used are to be paid for separately) (over 1000)


S07- 281


T-ELECTRICAL INSTALLATIONS

Recommended makes of Electrical Accessories

Recommended Fabricators of Switch boards and Enclosures.

ElsteelK.I.K. Lanka (Pvt) LtdPubudu Engineering (pvt) LtdRichardsons Projects (pvt) LtdBentota Power Generators (Pvt) LtdOS Project (Pvt) Ltd. (Orange)Or similar product

MCCB:- Merlin Gerine, ABB, Terasaki, Siemens or equivalent.

MCB’S & RCCB’S:- Merlin Gerine , Siemens, Crabtree, Hager, Moeller, Legrand, F & G (Austria) or equivalent.

Cable :- ACL, Kelani or equivalent.

Ceiling Fan:- K.D.K., National-Japanese originsExhaust Fan:- K.D.K., National-Japanese origins

Switch & socket outlet :- Tenby, Clipsal, MK, Crabtree, PDL, Kevilton, Orange or Equivalent.

Fluorescent Lamp:- The choke, starter and capacitor should be of good Quality. British, French, Australia, German or equivalent And the tube should be preferably Thorn, Osram National Or equivalent. The fluorescent fittings should be fabricated In gauge not smaller than 24 SWG Zinc coated metal, Finished with power coating (white in colour).

Distribution Board:- Shall be in surface mount metal enclosure fabricated With Zinc coated sheet metal of gauge not less than 1.8 mm total enclosed, with hinged door with protective cover plate for terminals, finished with powder coating of approved colour and components as specified in the BOQ.

Energy Saving Bulbs:- 4 star rated.


S07- 282


In PVC conduit

Lamp point wiring NosWater tight lamp point wiring NosIndoor Bracket lamp point wiring NosStair way lamp point wiring controlled by 2 No. two way switches NosCeiling fan point wiring complete with hook and sunk switch Nos5 AMP switch socket outlet NosIn PVC conduit

13 AMP switch socket outlet Nos15 AMP switch socket outlet Nos15 AMP switch socket outlet c/w 20A DP Switch with Neon Indicator Lamp

NosIn PVC Casing

Lamp point wiring NosWater tight lamp point wiring NosIndoor Bracket lamp point wiring NosStair way Lamp point wiring controlled by 2 No. two way switches. NosCeiling fan point wiring complete with fan hook and sunk switch. Nos5 AMP switch socket outlet NosIn PVC Casing

13 AMP switch socket outlet (Radial Circuit) Nos15 AMP switch socket outlet Nos15 AMP switch socket outlet c/w 20A DP NosDistribution Boards

2 way SP & N Distribution board complete with 30AMP 2P MCB and 40A 2P RCD(30mA)Nos



Point wiring to be carried out with 2x1mm2 PVC/PVC/CU + 2.5mm2 PVC/CU earth cable terminated in a 3 terminal ceilingrose and sunk switch, wired in concealed conduit in wall and above ceiling to be supplied and installed to working order

wiring to be carried out with 2C,2.5mm2 PVC/PVC/CU + 2.5mm2 PVC/CU earth cable wired in concealed conduit in wall and above ceiling to be supplied and installed to working order

point wiring to be carried out with 2x1mm2 PVC/PVC/CU + 2.5mm2 PVC/CU earth cable terminated in a 3 terminal ceiling rose and sunk switch, wired with PVC casing on wall and on soffit to be supplied and installed to working order.

Wiring to be carried out with 2C,2.5mm2 PVC/PVC/CU + 2.5mm2 PVC/CU earth cable wired in concealed conduit in wall and above ceiling to be supplied and installed to working order

Supply, Wiring and Installation of distribution board in surface mount plastic enclosure with the undermentioned switch gears to working order.


S07- 283











Nos

Nos

Nos

NosSupplying and Installation of 20-100AMP 4P MCCB in surface mount metal enclosure

NosSupplying and Installation of 30AMP 2P isolator complete with plastic enclosure.




NosSupplying and Installation of 40AMP 2P RCCB (30mA) complete plastic enclosure.



Nos

Supplying and Installation of 2 way TP & N Distribution board complete with 60 A 4P MCB and 2 No. 32 A 3P MCB (10kA) in surface mount plastic enclosure.

Supplying and Installation of 4 way TP & N Distribution board complete with 60 A 4P MCCB and 4 No. 16 A 3P MCB type 3 in surface mount metal enclosure.

Supplying and Installation of 2 way TP & N Distribution board complete with 100 A 4P MCCB and 2 No. 30/60AMP 3P MCCB in surface mount metal enclosure.

Supplying and Installation of 4 way TP & N Distribution board complete with 125 A 4P MCCB and 4 No. 30/60AMP 3P MCCB in surface mount metal enclosure.


S07- 284


Supplying and Installation of 60AMP 4P RCCB (30mA) complete plastic enclosure.Nos


S07- 285


Cabling in conduits

2x1 sq. mm + 2.5 sq. mm E cable M2x2.5 sq. mm + 2.5 sq. mm E cable M2x4 sq. mm + 2.5 sq. mm E cable M2x6 sq. mm + 6 sq. mm E cable M2x10 sq. mm + 10 sq. mm E cable M2x16 sq. mm + 16 sq. mm E cable M2x25 sq. mm + 16 sq. mm E cable M4x2.5 sq. mm + 2.5 sq. mm E cable M4x4 sq. mm + 4 sq. mm E cable M4x6 sq. mm + 6 sq. mm E cable M4x10 sq. mm +10 sq. mm E cable M4x16 sq. mm +16 sq. mm E cable M4x25 sq. mm +16 sq. mm E cable M4x35 sq. mm +16 sq. mm E cable MUnarmoured Cabling

2C Cu/PVC/PVC 1.5 sq. mm + 2.5 sq. mm E cable M2C Cu/PVC/PVC 2.5 sq. mm + 2.5 sq. mm E cable M2C Cu/PVC/PVC 4 sq. mm + 2.5 sq. mm E cable M2C Cu/PVC/PVC 6 sq. mm + 6 sq. mm E cable M2C Cu/PVC/PVC 10 sq. mm + 10 sq. mm E cable M2C Cu/PVC/PVC 35 sq. mm + 16 sq. mm E cable M1C Cu/XLPE/PVC 35 sq. mm + 16 sq. mm E cable M1C Cu/XLPE/PVC 50 sq. mm + 25 sq. mm E cable M1C Cu/XLPE/PVC 70 sq. mm + 35 sq. mm E cable MArmoured Cabling

4C Cu/XLPE/SWA/PVC 25 sq. mm M4C Cu/XLPE/SWA/PVC 35 sq. mm M4C Cu/XLPE/SWA/PVC 50 sq. mm M4C Cu/XLPE/SWA/PVC 70 sq. mm M4C Cu/XLPE/SWA/PVC 95 sq. mm M4C Cu/XLPE/SWA/PVC 120 sq. mm M4C Cu/XLPE/SWA/PVC 150 sq. mm MCabling in PVC Casing2x1 sq. mm + 2.5 sq. mm E cable M2x2.5 sq. mm + 2.5 sq. mm E cable M2x4 sq. mm + 2.5 sq. mm E cable M2x6 sq. mm + 6 sq. mm E cable M2x10 sq. mm +10 sq. mm E cable M

Cable shall be PVC/PVC/CU unless other wise specified to be supplied and installed in conduit to working order.

Cable shall be Cu/PVC/PVC OR Cu/XLPE/Cu supplied and installed in conduit or pressure pipe (type 1000) to working order.

Cable shall be Cu/XLPE/SWA/PVC (BS 5467 : 1997 600/1000V) supplied and installed in cable tile with necessary accessories & materials to working order.


S07- 286


2x16 sq. mm +16 sq. mm E cable M2x25 sq. mm +16 sq. mm E cable M4x2.5 sq. mm + 2.5 sq. mm E cable M4x4 sq. mm + 4 sq. mm E cable M4x6 sq. mm + 6 sq. mm E cable M4x10 sq. mm + 10 sq. mm E cable M4x16 sq. mm + 16 sq. mm E cable M4x25 sq. mm + 16 sq. mm E cable M4x35 sq. mm + 16 sq. mm E cable MEarth Electrode

NosLuminaries and Fixtures

Pendent Lamp C/W 250 mm dia. Conical plastic shade and 15W CFL bulb Nos

Pendent Lamp C/W 200 mm dia. Glass globe and 15W CFL bulb NosIndoor Bracket lamp C/W 200mm dia. Opal white glass globe & 11W CFL bulb

NosWater tight bracket lamp C/W 200mm dia. Clear aerylic globe & 15W CFL bulb(4 star rated)

Nos

Nos

Nos

Nos

NosFluorescent lamp fitting 1200mm single batten type with 1X36W bulb NosFluorescent lamp fitting 1200mm single totally encased suspension type with 1X36W bulb

NosFluorescent lamp fitting 600mm single totally encased suspension type with 1X18W bulb

Nos

Nos

Nos

NosFluorescent lamp fitting 1200mm single industrial type c/w 1X36W bulb (suspension type)

NosFluorescent lamp fitting 1200mm twin industrial type c/w 2X36W bulb (suspension type)

Nos

Supplying and Installation of earth Electrode 50 mm dia. Of 2 LM to working order complete with forming of a gulley around the pipe.

Supplying and Installation of Luminaries and fixtures complete with all fixing accessories, G.I. Chains cup hook 2/3 core cable, connector suspension holder etc. to working order.

Recessed fluorescent lamp fitting 1200mmx600mm complete with polished Aluminium double parabolic louver and 2X36W bulb




Fluorescent lamp fitting 1200mm single complete with prismatic diffuser and 1X36W bulb suspension type

Fluorescent lamp fitting 600mm single complete with prismatic diffuser and 1X18W bulb suspension type

Fluorescent lamp fitting 1200mm twin complete with prismatic diffuser and 2X36W bulb suspension type


S07- 287


Fluorescent lamp fitting 600mm single industrial type c/w 1X18W bulb (suspension type)Nos

NosCeiling lamp fitting C/W 250mm dia. Half spherical glass globe and 18W CFL bulb

NosBulk head lamp water tight C/W 18W CFL bulb (4 star rated) NosSwitch socket outlet

5 AMP switch socket outlet Nos13 AMP switch socket outlet Nos15 AMP switch socket outlet NosReplacing sunk switch

Replacing 1 gang sunk switch NosReplacing 2 gang sunk switch NosReplacing 3 gang sunk switch NosReplacing 4 gang sunk switch NosReplacing 5 gang sunk switch NosReplacing fan regulator dimmer type NosReplacing Ceiling fan regulator NosReplacing 20 AMP DP switch with Neon indicator NosReplacing sunk Bell push NosReplacing Cell Bell Ding Dong type excluding wires NosFans

NosExhaust Fans

Nos

Nos

Nos

NosWall Fans

NosFluorescent LampSupply & Installation of fluorescent lamp components to working order20W/40W Choker Nos20W/40W starter Nos

Recessed Down light fitting complete with 200mm dia. Polished Aluminium reflector and 20W CFL bulb

Switch socket outlet 5AMP/13Amp/15AMP to be supplied and installed complete with screws etc. to working order. ( Excluding wires & conduits )

Replacing sunk switch complete with plastic sunk box to be supplied and installed to working order.

Supply & Installation of Ceiling fan 1400mm dia. Complete with 3 speed regulator (Excluding wiring)

Supply & Installation of 200mm dia. Exhaust fan with auto shutter (K.D.K or equivalent) (Excluding wiring)




Supply & Installation of wall fan 450mm dia. Complete with 3 speed regulator (Excluding wiring)


S07- 288


Capacitor 2.5-3.5MF NosFluorescent bulb 36W NosConduit PipeSupplying & installation of conduit pipe clipped in surface18mm conduit pipe M20mm conduit pipe M25mm conduit pipe M30mm conduit pipe M40mm conduit pipe M50mm conduit pipe MPVC CasingSupplying and Installation of PVC casing10mmx20mm PVC Casing M14mmx24mm PVC Casing M16mmx40mm PVC Casing M25mmx40mm PVC Casing M50mmx25mm PVC Casing M50mmX50mm PVC Box Casing M50mmX75mm PVC Box Casing M100mmX50mm PVC Box Casing M100mmx27mm PVC Box Casing MCommissioning Wires 2x1 sq. mm Cu/PVC/PVC Cable M2 x 2.5 sq. mm Cu/PVC/PVC Cable M2 x 4 sq. mm Cu/PVC/PVC Cable M2 x 6 sq. mm Cu/PVC/PVC Cable M2 x 10 sq. mm Cu/PVC/PVC Cable M2 x 16 sq. mm Cu/PVC/PVC Cable M2 x 25 sq. mm Cu/PVC/PVC Cable M2 x 35 sq. mm Cu/PVC/PVC Cable MCommissioning Earth Wires 2.5 sq. mm Cu/PVC Earth cable M6 sq. mm Cu/PVC Earth cable M10 sq. mm Cu/PVC Earth cable M16 sq. mm Cu/PVC Earth cable MSUPPLY & INSTALLATION OF DOL STARTERSingle phase DOL starter for 5.5kW motor (without overload) NosThree phase DOL starter for 5.5kW motor (without overload) Nos


S07- 289


U-ALUMINIUM FABRICATORBoards and Glass PansOne Side Fabric Pasted 3mm thick Ply Wood Boards for Partitions

sq.ft

sq.ftPVC Laminated Ply Board for Partitions, Doors or Windows

sq.ftOne Side Coloured Al. Composite Cladding Boards for Partitions only

sq.ftOne Side Coloured Al. Composite Cladding Boards for Doors and Windows

sq.ftBoth Sides Coloured Al. Composite Cladding Boards for Partitions only

sq.ftBoth Sides Coloured Al. Composite Cladding Boards for Doors and Windows

sq.ftClear Glass 5mm thick for Partitions only

sq.ft

Supplying & Fabricating of Panel Boards consist of fabric cloths (Alabama or equivalent.) and sponge sheets pasted on one side of the ply wood board (3mm thick) and fix to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.

Both Sides Fabric Pasted 3mm thick Ply Wood Boards for Partitions, Doors or Windows

Supplying & Fabricating of Panel Boards consist of fabric cloths (Alabama or equivalent.) and sponge sheets pasted on BOTH sides of the ply wood board (3mm thick) and fix to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.

Supplying, Fabricating and Fixing 3mm thick PVC Laminated Ply Boards to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)

Supplying, Fabricating & Fixing of 4mm thick Al. Composite Cladding Boards (One side Coloured) to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)

Supplying, Fabricating & Fixing of 4mm thick Al. Composite Cladding Boards (One side Coloured) to existing door or window frame work with necessary rubber beadings.

Supplying, Fabricating & Fixing of 4mm thick Al. Composite Cladding Boards in SINGLE SIDE of the existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)

Supplying, Fabricating & Fixing of 4mm thick Al. Composite Cladding Boards in SINGLE SIDE of the existing door or window frame work with necessary rubber beadings.

Supplying and Fixing of 5mm thick clear glass pan to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)


S07- 290


Clear Glass 5mm thick for Doors and Windows

sq.ftSupplying and Fixing of 5mm thick clear glass pan to existing door or window frame work with necessary rubber beadings.


S07- 291


Float Glass 5mm thick for Partitions only

sq.ftFloat Glass 5mm thick for Doors and Windows

sq.ftTinted Glass 5mm thick for Partitions only

sq.ftTinted Glass 5mm thick for Doors and Windows

sq.ftClear Glass 6mm thick for Partitions only

sq.ftClear Glass 6mm thick for Doors and Windows

sq.ftSand Blast StickersSupplying cutting and pasting of sand blast stickers in position. sq.ft

Note: Refer figures for more details

Typical Aluminium Louvers

Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ftWood Finished Louver blades sq.ft

Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ft

Supplying and Fixing of 5mm thick float glass pan to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)

Supplying and Fixing of 5mm thick float glass pan to existing door or window frame work with necessary rubber beadings.

Supplying and Fixing of 5mm thick tinted glass pan to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)

Supplying and Fixing of 5mm thick tinted glass pan to existing door or window frame work with necessary rubber beadings.

Supplying and Fixing of 6mm thick clear glass pan to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)

Supplying and Fixing of 6mm thick clear glass pan to existing door or window frame work with necessary rubber beadings.

Aluminium Louvers with Louver Frame (52.5mm high 34.6mm wide Louver blades; Alumex DG 01 or equivalent)

Supplying, Fabricating and Fixing 1.2mm thick 52.5mm high 34.6mm wide Louver blades (Alumex DG 01 or equivalent) to 20.0 X 37.0mm louver frame (Alumex DG 101 or equivalent) and fix to existing door, window or partition frame work including necessary accessories.

Aluminium Louvers with Louver Frame (60.0mm high 28.5mm wide Louver blades; Alumex DG 03 or equivalent)

Supplying, Fabricating and Fixing 1.2mm thick 60.0mm high 28.5mm wide Louver blades (Alumex DG 03 or equivalent) to 17.0 X 31.0mm louver frame (Alumex DG 103 or equivalent) and fix to existing door, window or partition frame work including all accessories.


S07- 292


Wood Finished Louver blades sq.ft


S07- 293




Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ftWood Finished Louver blades sq.ftAluminium SUN Louvers with Louver Frame (Alumex ALU 180 or equivalent)

Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ft

Aluminium Louvers with Louver Frame (34.5mm high 28.5mm wide symmetrical "Y" type Louver blades; Alumex DG 04 or equivalent)Supplying, Fabricating and Fixing 1.2mm thick 34.5mm high 28.5mm wide symmetrical "Y" type Louver blades (Alumex DG 04 or equivalent) to 17.0 X 31.0mm louver frame (Alumex DG 103 or equivalent) and fix to existing door, window or partition frame work including all accessories.

Aluminium Louvers (39.5mm high 37.4mm wide asymmetrical "Y" type Louver blades; Alumex DG 06 or equivalent) with Louver Frame

Supplying, Fabricating and Fixing 1.2mm thick 39.5mm high 37.4mm wide asymmetrical "Y" type Louver blades (Alumex DG 06 or equivalent) to 17.0 X 40.0mm louver frame (Alumex DG 104 or equivalent) and fix to existing door, window or partition frame work including all accessories.

Aluminium Louvers (120.0mm high 37.4mm wide Louver blades; Alumex DG 05 or equivalent) with Louver Frame

Supplying, Fabricating and Fixing 1.5mm thick 120.0mm high 37.4mm wide Louver blades (Alumex DG 05 or equivalent) to 17.0 X 40.0mm louver frame (Alumex DG 104 or equivalent) and fix to existing door, window or partition frame work including all accessories

Supplying, Fabricating and Fixing 1.5mm thick 107.3mm high 26.0mm wide sun Louver blades (Alumex ALU-180 or equivalent) to 25.0 X 125.0mm louver frame (Alumex ALU-181 or equivalent) and fix to existing frame or wall. (Fix to existing frame or wall with accessories paid separately)


S07- 294


Wood Finished Louver blades sq.ft


S07- 295


Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ftWood Finished Louver blades sq.ftSingle Row Aluminium Partition Frame Work with Boards/Glass

Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft


Aluminium SUN Louvers (Alumex ALU 180 or equivalent) with BIRD'S MOUTH BRACKETS (Alumex ALU 282 or equivalent)

Supplying, Fabricating and Fixing 1.5mm thick 107.3mm high 26.0mm wide sun Louver blades (Alumex ALU-180 or equivalent) to Bird's mouth brackets (Alumex ALU-282 or equivalent) and fix to existing frame, Door, Window or wall with all accessories.

Single row Aluminium Partition Frame Work(1.2mm thick ) with Fully Board Panels (max. Height 1200mm)

Supplying, Fabricating and Installing of single row frame work with FULLY BOARDED panels in both sides for ALUMINIUM PARTITION consist of 1.2mm thick,76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And GI channel stiffener frame work enclosed in Aluminium frame work with an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (PANNLE BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

Single row Aluminium Partition Frame Work(1.2mm thick ) Fully Glass Pans (max. Height 1200mm)

Supplying, Fabricating and Installing single row panel frame work with Fully Glass ALUMINIUM PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space consist of glass pans. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-


S07- 296


Single Row Aluminium Partition Frame Work with Louvers

Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2 Row Aluminium Partition Frame Work with Boards/Glass


Single Row Aluminium Partition Frame Work (1.2mm thick) Fully Louvered (max. Height 1200mm)

Supplying, Fabricating and Installing single row panel FULLY ALUMINIUM LOUVER PARTITION with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and consist of Aluminium louver framed panel. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

Two Row Compiled Aluminium Partition Frame Work (1.2mm thick) Fully Board Panels (max. height 2400mm)

Supplying, Fabricating and Installing two rows of panel frame work with FULLY BOARDED panels in both sides for(Top & Bottom rows) ALUMINIUM PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And GI channel stiffener frame work enclosed in Aluminium frame work with an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (PANEL BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-


S07- 297




Two Row Compiled Aluminium Partition Frame Work (1.2mm thick) - One Row with Boards & other Row with Glass Pans (max. height 2400mm)

Supplying, Fabricating and Installing GLASS & BOARD two rows of panel ALUMINIUM PARTITION frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And one row consist of BOAD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings to be placed in 600mm centers at vertical direction and other row consist of glass pans, span not exceeding 1200mm in both directions. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS & PANEL BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

Two Row compiled Aluminium Partition Frame Work (1.2mm thick) - with Fully Glass Pans

Supplying, Fabricating and Installing two rows of panel frame work with Fully Glass pans for (Top & Bottom rows) ALUMINIUM PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-


S07- 298


2 Row Aluminium Partition Frame Work with Louvers & Boards/Glass



Two Row compiled Aluminium Partition Frame Work (1.2mm thick)-One Row with Louvers and other Row with Boards (max. height 2400mm)

Supplying, Fabricating and Installing of LOUVER & BOARD two rows of panels ALUMINIUM PARTITION frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions, One row consist of BOARD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in Aluminium frame, with appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Other row consists of LOUVER framed panels. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE & PANEL BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

Two Row compiled Aluminium Partition Frame Work (1.2mm thick)-One Row with Louvers and other Row with Glass (max. height 2400mm)

Supplying, Fabricating and Fixing LOUVER & GLASS two rows of panels ALUMINIUM PARTITION frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and one row consist of glass pans. Other row consists of LOUVER framed panels. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE & GLASS PANS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-


S07- 299


Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft3 Row Aluminium Partitions

1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) extrusions

Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2.0mm thick,100mm depth (width 50.0mm) (Alumex or eq.) Aluminium extrusions


Two Row compiled Aluminium Partition Frame Work (1.2mm thick) - Fully Louvered (max. height 2400mm)

Supplying, Fabricating and Fixing 2 rows of panel FULLY Aluminium LOUVER Partition with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and both rows consist of Aluminium louver framed panels. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

3 Row Compiled Aluminium Partition Frame Work (max. height 3600mm) - with Fully Board

Supplying, Fabricating and Installing 3 Row Compiled panel frame work with FULLY BOARDED panels in both sides for (Top middle & Bottom rows); ALUMINIUM PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions and GI channel stiffener frame work enclosed in Aluminium frame work with an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (PANEL BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-


S07- 300



Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2.0mm thick,100mm depth (width 50.0mm) (Alumex or eq.) extrusions



Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ft

3 Row Compiled Aluminium Partition Frame Work - 2 Rows with Boards & Other Row with Glass Pans (max. height 3600mm)

Supplying, Fabricating and Installing GLASS & BOARD 3 row Compiled panel ALUMINIUM PARTITION frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And two rows consist of BOAD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Other row consists of glass pans, span not exceeding 1200mm in both directions. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS & PANEL BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

3 Row Compiled Aluminium Partition Frame Work - 1 Row with Boards & Other 2 Rows with Glass Pans (max. height 3600mm)

Supplying, Fabricating and Installing GLASS & BOARD 3 row Compiled panel ALUMINIUM PARTITION frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And one row consists of BOAD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Other two rows consist of glass pans, span not exceeding 1200mm in both directions. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS & PANEL BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-


S07- 301


Bronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ft


S07- 302


Wood Finished Aluminium extrusion frame work sq.ft2.0mm thick, 100mm depth (width 50.0mm) (Alumex or eq.) extrusions



Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2.0mm thick, 100mm depth (width 50.0mm) (Alumex or eq.) extrusions


3 Row Compiled Aluminium Partition Frame Work - (max. height 3600mm) fully Glass Panels

Supplying, Fabricating and Installing 3 Row Compiled panel frame work with FULLY GLAZE pans for (Top middle & Bottom rows) ALUMINIUM PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions and glass pans, to form an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions suited to the available space. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-


S07- 303


3 Panel Aluminium Louver Partitions

1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions

Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2.0mm thick, 100mm depth (width 50.0mm) (Alumex or eq.) Aluminium extrusions


3 Row Compiled Aluminium Partition Frame Work - (max. height 3600mm) one row with Louvers, Another row With Boards & Remaining row with Glass.

Supplying, Fabricating and Fixing 3 Row Compiled panel frame work with GLASS, BOARD & ALUMINIUM LOUVER PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And one row consists of BOAD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Another row consists of necessary LOUVER framed panels & remaining row consists of glass pans suited to the available space. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE, GLASS PANS & PANEL BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

3 Row Compiled Aluminium Partition Frame Work - (max. height 3600mm) one row with Louvers, Remaining two rows with Boards.


S07- 304


Supplying, Fabricating and Fixing 3 Row Compiled panel frame work with BOARD & ALUMINIUM LOUVER PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And two rows consist of BOAD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Other remaining row consists of necessary LOUVER framed panels. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE & PANEL BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-


S07- 305








3 Row Compiled Aluminium Partition Frame Work - (max. height 3600mm) one row with Louvers, Remaining two rows with Glass.

Supplying, Fabricating and Fixing LOUVER & GLASS 3 Row Compiled panel Aluminium Partition frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space. Two rows consist of glass pans. Other row consists of LOUVER panel frame with appropriate grid pattern suited to glass panels. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE & GLASS PANS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-


S07- 306





Aluminium 76mm Shopfront

Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ftAluminium 100mm Shopfront

3 Row Compiled Aluminium Partition Frame Work - (max. height 3600mm) Fully Louvered.

Supplying, Fabricating and Fixing 3 Row Compiled panel FULLY ALUMINIUM LOUVERED PARTITION with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and all rows consist of Louvers enclosed with Aluminium louver frame. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH LOUVER FRAME PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

Supplying, Fabricating and Installing 1.2 mm thick,76mmAluminium Shopfront, frame work fixed as an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suit to the available space including necessary rubber beadings, fasteners etc. (SUPPLY & FIXING OF LOUVERS, GLASS PANS OR PANNLE BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-


S07- 307


Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ftAluminium Curtain Wall (2.0mm thick)

Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ftAluminium Curtain Wall (1.5mm thick)


Aluminium doors

Supplying, Fabricating and Fixing 1.5 mm thick,100mmAluminium Shopfront, frame work fixed as an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suit to the available space including necessary rubber beadings, fasteners etc. (SUPPLY & FIXING OF LOUVERS, GLASS PANS OR PANNLE BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

Supplying, Fabricating and Fixing Aluminium Curtain Wall with 2.0mm thick,98mm depth extrusions, frame work fixed as an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suit to the available space including necessary rubber beadings, fasteners etc. (SUPPLY & FIXING OF LOUVERS, GLASS PANS OR PANNLE BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

Supplying, Fabricating and Fixing Aluminium Curtain Wall with 1.5mm thick,85mm depth extrusions, frame work fixed as an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suit to the available space including necessary rubber beadings, fasteners etc. (SUPPLY & FIXING OF LOUVERS, GLASS PANS OR PANNLE BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

Aluminium Double Sashed Swing Door (sash only) for 1.6mm thick 100mm Deep Door Frames


S07- 308


-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft

Supplying, Fabricating and Installing of Aluminium Double sashed Swing Door (sash only) for 1.6mm thick 100mm deep door frames with suitable wool felt. Rate inclusive of necessary fasteners and hinges (Union or equivalent 102x76x2 mm) etc.( Glass/ Board, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 100D-102, 100D-103, 100D-201, 100D-301, 100D-401, 100D-501 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U207-U241 for outer frame-


S07- 309



Door Outer frames

-DO- Matt Finished Aluminium L.ft -DO- Natural Anodized Aluminium L.ft -DO- Bronzed Anodized Aluminium L.ft -DO-Powder Coated Aluminium L.ft -DO-Wood Finished Aluminium L.ft


Aluminium Single Sashed Swing Door (sash only) for 1.6mm thick 100mm Deep Door Frames

Supplying, Fabricating and Installing of Aluminium Single sashed Swing door (sash only) for 1.6mm 100mm deep door frames with suitable wool felt. Rate inclusive of necessary fasteners and hinges (Union or equivalent 102x76x2 mm) etc.( Glass/ Board/ Louver Panels, Door closers, door locks and door handles paid separately) door sash only.(Alumex extrusion No's 100D-101, 100D-103, 100D-201, 100D-301, 100D-401, 100D-501 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U207-U241 for outer frame-

Outer Door Frame (Frame Only) with1.6mm thick 100mm deep Extrusion for Aluminium Double Sashed Swing Door

Supplying, Fabricating and Installing 1.6mm thick 45mm X 100mm (depth) Aluminium outer door frame for double sash Swing door. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion No. 100D-3004H or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-

Outer Door Frame (Frame Only) with1.5mm thick 100mm deep Extrusion for Aluminium Single Sashed Swing Door

Supplying, Fabricating and Installing 1.5mm thick 45mmX100mm (depth) Aluminium Single sashed Swing door outer frame only. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion No. 100D-3005 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-


S07- 310





Outer Door Frame (Frame Only) with 1.2mm thick 76mm deep Extrusion for Aluminium Single Sash Swing door

Supplying, Fabricating and Installing 1.2mm thick 45mmX76.2mm (depth) Aluminium Single sashed Swing door outer frame only. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion No. 76D-3102 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-

Outer Door Frame (Frame Only) with 1.5mm thick 100mm Deep SHOP FRONT Aluminium Extrusions

Supplying, Fabricating and Installing 1.5mm thick 100mm (depth) Aluminium Swing door outer frame for SHOP FRONT. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SPR-205, SPR-211or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-

Outer Door Frame (Frame Only) with 1.2mm thick 76mm Deep SHOP FRONT Aluminium Extrusions

Supplying, Fabricating and Installing 1.2mm thick 76mm (depth) Aluminium Swing door outer frame for SHOP FRONT. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SPR-105, SPR-211 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-

Outer Door Frame (Frame Only) with 1.2mm thick 76mm Deep Partition Frame Aluminium Extrusions


S07- 311




Aluminium Sliding Doors

80mm (1.5 mm thick) Aluminium Sliding Door (Undivided plane Paneled Sashes)


Supplying, Fabricating and Installing 1.2mm thick 76mm (depth) Aluminium Swing door outer frame with Aluminium Partition extrusions. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. PT-5159 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-

Outer Door Frame (Frame Only) with 1.2mm thick 76mm Deep Aluminium Extrusion for Single Sash Plywood door

Supplying, Fabricating and Installing 1.2mm thick 76mm (depth) Aluminium door outer frame for single sashed plywood door. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 76D-3101 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, H069-H072 for plywood door-

Supplying, Fabricating and Installing 1.5mm thick 33.7mmX80mm (depth) Aluminium framed two sliding door sashes (Undivided plane Paneled Sashes) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 80S-2001, 80S-2002, 80S2101 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

80mm (1.5 mm thick) Aluminium Sliding Door (Undivided plane Paneled Sashes) with top fixed panels


S07- 312



Supplying, Fabricating and Installing 1.5mm thick 33.7mmX80mm (depth) Aluminium framed two sliding door sashes (Undivided plane Paneled Sash) with top fixed panels. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 80S-2001, 80S-2002, 80S2101 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-


S07- 313


100mm (1.5 mm thick) Aluminium Sliding Door (Undivided plane Paneled Sashes)



100mm (1.5 mm thick) Aluminium Sliding Door (Sashes Divided to two Panels)


Supplying, Fabricating and Installing 1.5mm thick 30mmX98mm (depth) Aluminium framed one half fixed & Single Sliding Door sash (Undivided plane Paneled Sashes) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001, DS-1101, SD1501 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

100mm (1.5 mm thick) Aluminium Sliding Door (Undivided plane Paneled Sashes) with top fixed panel

Supplying, Fabricating and Installing 1.5mm thick 30mmX98mm (depth) Aluminium framed one half fixed & Single Sliding Door sash (Undivided plane Paneled Sashes) with top fixed panels. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001, DS-1101, SD1501 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

Supplying, Fabricating and Installing 1.5mm thick 30mmX98mm (depth) Aluminium framed one half fixed & Single Sliding Door sash (Sashes Divided to two Panels) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001, DS-1101, SD1501 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-


S07- 314




80mm (1.5 mm thick) Aluminium 3 track Sliding Door (Sashes Divided to two Panels)


100mm (1.5 mm thick) Aluminium Sliding Door (Sashes Divided to two Panels) with top fixed panel

Supplying, Fabricating and Installing 1.5mm thick 30mmX98mm (depth) Aluminium framed one half fixed & Single Door sash (Sashes Divided to two Panels) with top fixed panels. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001, DS-1101, SD1501 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

80mm (1.5 mm thick) Aluminium 3 track Sliding Door (Undivided plane Paneled Sashes)

Supplying, Fabricating and Installing 1.5mm thick 33.7mmX119.5mm (depth) Aluminium framed 80mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Undivided plane Paneled Sashes) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 80S-2001A, SS-2101, 80SFL-1001 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

Supplying, Fabricating and Installing 1.5mm thick 33.7mmX119.5mm (depth) Aluminium framed 80mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Sashes Divided to two Panels) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 80S-2001A, SS-2101, 80SFL-1001 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-


S07- 315




100mm (1.6 mm thick) Aluminium 3 track Sliding Door (Sashes Divided to two Panels)


100mm (1.6 mm thick) Aluminium 3 track Sliding Door (Undivided plane Paneled Sashes)

Supplying, Fabricating and Installing 1.6mm thick 35mmX146.5mm (depth) Aluminium framed 100mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Undivided plane Paneled Sashes) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001A, SD-1101A, SD-1302 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

100mm (1.6 mm thick) Aluminium 3 track Sliding Door (Undivided plane Paneled Sashes) with top fixed panel

Supplying, Fabricating and Installing 1.5mm thick 35mmX146.5mm (depth) Aluminium framed 100mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Undivided plane Paneled Sashes) with top fixed panel. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001A, SD-1101A, SD-1302 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

Supplying, Fabricating and Installing 1.6mm thick 35mmX146.5mm (depth) Aluminium framed 100mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Sashes Divided to two Panels) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001A, SD-1101A, SD-1302 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-


S07- 316





100mm (1.6 mm thick) Aluminium 3 track Sliding Door (Sashes Divided to two Panels) with top fixed panel

Supplying, Fabricating and Installing 1.6mm thick 35mmX146.5mm (depth) Aluminium framed 100mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Sashes Divided to two Panels) with top fixed panel. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001A, SD-1101A, SD-1302 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

100mm (1.5 mm thick) Aluminium Double Glazed Sliding Door (Sashes Divided to two Panels)

Supplying, Fabricating and Installing 1.5mm thick 42.5mmX100mm (depth) Aluminium framed Double Glazed one half fixed & Single Sliding Door sash (Double Glazed Sashes Divided to two Panels) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SDG-2001, SDG-2101, SDG-2401 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

100mm (1.5 mm thick) Aluminium Double Glazed Sliding Door (Sashes Divided to two Panels) with top fixed panel

Supplying, Fabricating and Installing 1.5mm thick 42.5mmX100mm (depth) Aluminium framed Double Glazed one half fixed & Single Sliding Door sash (Double Glazed Sashes Divided to two Panels) with top fixed panels. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SDG-2001, SDG-2101, SDG-2401 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-


S07- 317


Aluminium Casement WindowsCasement Window Frames Only

41mm Aluminium Casement Window Frame for Single Sash (Frame Only)





41mm Aluminium Casement Window Frame for Double Sash (Frame Only)


-DO- Matt Finished Aluminium sq.ft

Supplying, Fabricating & Installing of 1.2mm thick 41mm deep Aluminium Casement window frame only. Rate to include for rubber beadings, rawl plugs, fasteners etc. Window sash, Fixed Panels, Louver Panels, hinges, locks paid separately. (Alumex extrusion Nos. CA-1007, CA-1008 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U647-U676 for window sashes-

41mm Aluminium Casement Window Frame for Single Sash with Top Fixed Panel (Frame Only)

41mm Aluminium Casement Window Frame for Single Sash with Both Side Fixed Panels (Frame Only)

41mm Aluminium Casement Window Frame for Single Sash with Top and Both Side Fixed Panels

41mm Aluminium Casement Window Frame for Double Sash with Top Fixed Panel (Frame Only)


S07- 318


-DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft



41mm Aluminium Casement Window Frame for 3 Sashes (Frame Only)





41mm Aluminium Casement Window Frame for Double Sash with Both Side Fixed Panels (Frame Only)

41mm Aluminium Casement Window Frame for Double Sash with Top & Both Side Fixed Panels (Frame Only)

41mm Aluminium Casement Window Frame for 3 Sashes with Top Fixed Panel (Frame Only)

41mm Aluminium Casement Window Frame for 3 Sashes with Both Side Fixed Panels (Frame Only)

41mm Aluminium Casement Window Frame for 3 Sashes with Both Sides and Top Fixed Panels (Frame Only)


S07- 319







60mm Aluminium Casement Window Frame for Single Sash (Frame Only)


-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft




Supplying, Fabricating & Installing of 1.2mm thick 60mm deep Aluminium Casement window frame only. Rate to include for rubber beadings, rawl plugs, fasteners etc. Window sash, Fixed Panels, Louver Panels, hinges, locks paid separately. (Alumex extrusion Nos. CA 1009 & CA 1010 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U647-U676 for window sashes-

60mm Aluminium Casement Window Frame for Single Sash with Top Fixed Panel (Frame Only)


S07- 320


-DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft



60mm Aluminium Casement Window Frame for Double Sash (Frame Only)






60mm Aluminium Casement Window Frame for Single Sash with Both Side Fixed Panels (Frame Only)

60mm Aluminium Casement Window Frame for Single Sash with Top & Both Side Fixed Panels (Frame Only)

60mm Aluminium Casement Window Frame for Double Sash with Top Fixed Panel (Frame Only)

60mm Aluminium Casement Window Frame for Double Sash with Both Side Fixed Panels (Frame Only)

60mm Aluminium Casement Window Frame for Double Sash with Top & Both Side Fixed Panels (Frame Only)


S07- 321









-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft







S07- 322


-DO-Wood Finished Aluminium sq.ft






-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft


Supplying, Fabricating & Installing of 1.2mm thick 70mm deep single sashed Matt Finished Aluminium Casement window frame only. Rate to include for rubber beadings, rawl plugs, fasteners etc. Window sash, Fixed Panels, Louver Panels, hinges, locks paid separately. (Alumex extrusion Nos. CA 1011 & CA 1012 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U647-U676 for window sashes-

70mm (1.2mm thick) Aluminium Casement Window Frame for Single Sash (Frame Only)

70mm (1.2mm thick) Aluminium Casement Window Frame for Single Sash with Top Fixed Panel (Frame Only)

70mm (1.2mm thick) Aluminium Casement Window Frame for Single Sash with Both Side Fixed Panels (Frame Only)

70mm (1.2mm thick) Aluminium Casement Window Frame for Single Sash with Top & Both Side Fixed Panels (Frame Only)

70mm (1.2mm thick) Aluminium Casement Window Frame for Double Sash (Frame Only)


S07- 323


-DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft




70mm (1.2mm thick) Aluminium Casement Window Frame for 3 Sashes (Frame Only)




70mm (1.2mm thick) Aluminium Casement Window Frame for Double Sash with Top Fixed Panel (Frame Only)

70mm (1.2mm thick) Aluminium Casement Window Frame for Double Sash with Both Side Fixed Panels (Frame Only)

70mm (1.2mm thick) Aluminium Casement Window Frame for Double Sash with Top & Both Side Fixed Panels (Frame Only)

70mm (1.2mm thick) Aluminium Casement Window Frame for 3 Sashes with Top Fixed Panel (Frame Only)

70mm (1.2mm thick) Aluminium Casement Window Frame for 3 Sashes with Both Side Fixed Panels (Frame Only)


S07- 324








-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft

70mm (1.2mm thick) Aluminium Casement Window Frame for 3 Sashes with Both Sides and Top Fixed Panels (Frame Only)




Supplying, Fabricating & Installing of 1.5mm thick 70mm deep single sashed Matt Finished Aluminium Casement window frame only. Rate to include for rubber beadings, rawl plugs, fasteners etc. Window sash, Fixed Panels, Louver Panels, hinges, locks paid separately. (Alumex extrusion Nos. CA 1013,CA 1014 & CA 1015 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U647-U676 for window sashes-

70mm (1.5mm thick) Aluminium Casement Window Frame for Single Sash (Frame Only)


S07- 325









70mm (1.5mm thick) Aluminium Casement Window Frame for Single Sash with Top Fixed Panel (Frame Only)



70mm (1.5mm thick) Aluminium Casement Window Frame for Double Sash (Frame Only)

70mm (1.5mm thick) Aluminium Casement Window Frame for Double Sash with Top Fixed Panel (Frame Only)

70mm (1.5mm thick) Aluminium Casement Window Frame for Double Sash with Both Side Fixed Panels (Frame Only)

70mm (1.5mm thick) Aluminium Casement Window Frame for Double Sash with Top & Both Side Fixed Panels (Frame Only)


S07- 326










-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft






S07- 327


-DO-Wood Finished Aluminium sq.ft






S07- 328


Aluminium Casement & Pivot Window (Frame Only)




Casement Window Sash Only


Supplying, Fabricating & Installing of 1.2mm thick 70mm deep single sashed Matt Finished Aluminium Casement & Pivot window frame only. Rate to include for rubber beadings, rawl plugs, fasteners etc. Window sash, Fixed Panels, Louver Panels, hinges, locks paid separately. (Alumex extrusion Nos. CA-1011,CA-1012 & PV-1001 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U647-U676 for window sashes-

70mm (1.2mm thick) Aluminium Casement & Pivot Window Frame for Single Sash (Frame Only)

70mm (1.2mm thick) Aluminium Casement & Pivot Window Frame for Single Sash with Top Fixed Panel (Frame Only)

70mm (1.2mm thick) Aluminium Casement & Pivot Window Frame for Single Sash with Both Side Fixed Panels (Frame Only)

Aluminium Casement Window Sash (Sash Only) for 41mm, 60mm or 70mm (1.2mm tk.) frames

Supplying, Fabricating & Installing of 1.2mm thick 40mm X 35mm (depth) Matt Finished Aluminium Casement window sash only. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion No. CA-2005 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-


S07- 329


Aluminium Casement Window Sash (Sash Only) for 70mm (1.5mm tk.) frame work


70mm (1.5mm tk.) Divided Casement Window Sash Only



Supplying, Fabricating & Installing of 1.5mm thick 54.5mm X 35mm (depth) Matt Finished Aluminium Casement window sash only. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion No. CA-2007 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-

Aluminium Casement Divided Window Sash (Sash Divided to 2 portions) for 70mm (1.5mm tk.) frame work

Supplying, Fabricating & Installing of 1.5mm thick 62mm X 35mm (depth) Matt Finished Aluminium Casement Divided window sash consist of two portions. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion Nos. CA-1116, CA-2008 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-


Supplying, Fabricating & Installing of 1.5mm thick 62mm X 35mm (depth) Matt Finished Aluminium Casement Divided window sash consist of 4 portions. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion Nos. CA-1116, CA-2008 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-


S07- 330



70mm (1.2mm thick) Aluminium Casement & Pivot Window Sash Only


Aluminium Sliding windows1.3mm thick 70mm Aluminium Sliding windows

1.3mm thick 70mm 1 Sash Fixed, Single Sash Aluminium Sliding window

-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft


Supplying, Fabricating & Installing of 1.5mm thick 62mm X 35mm (depth) Matt Finished Aluminium Casement Divided window sash consist of 6 portions. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion Nos. CA-1116, CA-2008 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-

Supplying, Fabricating & Installing of 1.5mm thick 42.5mm X 40mm (depth) Matt Finished Aluminium Casement & Pivot window sash only. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion No. PV-2001 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-

Supplying, Fabricating & Fixing Matt finished Aluminium Window 1.3mm thick ,70mm depth Aluminium Framed (max. width 33.4mm) and Signal sash(max. width 56.2mm) Sliding Window. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 70S-1002, 70S-1202 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-


S07- 331


1.3mm thick 70mm Double Sashed Aluminium Sliding window


-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft1.3mm thick 70mm 4 Sashed Aluminium Sliding window


Supplying, Fabricating & Fixing matt finished Aluminium window with 1.3mm thick ,70mm depth Aluminium framed (max. width 32.0mm) Double sash(max. width 36.2mm)Sliding Window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 70S-1001, 70S-1201-1, 70S-1101-1, 70S-1401, 70S-1501, 70S-1601, 70S-1701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

1.3mm thick 70mm Double Sashed Aluminium Sliding window with 2 Fixed Panels at Top or Bottom

Supplying, Fabricating & Matt finished Aluminium Window with 1.3mm thick ,70mm depth Aluminium Framed (max. width 61.0mm) Double sash (max. width 56.2mm) Sliding Window with Two fixed panels on top to the window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately.(Alumex extrusion No. 70S-1012, 70S-1201-1, 70S-1101-1, 70S-1401, 70S-1501, 70S-1601, 70S-1701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

Supplying, Fabricating & Fixing matt finished Aluminium Window with 1.3mm thick ,70mm depth Aluminium Framed (max. width 32.0mm) and Four Sliding Sashes(max. width 30.0mm) including necessary beadings, sliding locks etc. Glass pans, Window panel boards or Louver Panels paid separately.(Alumex extrusion No. 70S-1206, 70S-1001-1, 70S-1101-1, 70S-1401, 70S-1501, 70S-1601, 70S-1701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-


S07- 332


-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft1.5mm thick 80mm Aluminium Sliding window

1.5mm thick 80mm 1 Sash Fixed Single Sash Aluminium Sliding window

-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft1.5mm thick 80mm Double Sashed Aluminium Sliding window


1.3mm thick 70mm 4 Sashed Aluminium Sliding window with 4 Sliding Panels at Top or Bottom

Supplying, Fabricating & Fixing Aluminium Window with 1.3mm thick ,70mm depth Aluminium Framed (max. width 60.0mm) Four Sliding Sashes(max. width 30.0mm) with Four Sliding panels on Top or Bottom of the Window including necessary beadings, sliding locks etc. Glass pans, Window panel boards or Louver Panels paid separately.(Alumex extrusion No. 70S-1201-1, 70S-1001-1, 70S-1006, 70S-1914, 70S-1401, 70S-1501, 70S-1601, 70S-1701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

Supplying, Fabricating & Fixing Aluminium Window with 1.5mm thick ,80mm depth Aluminium Framed (max. width 43.5mm) Signal Sash (max. width 58.0mm) Sliding Window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately.(Alumex extrusion No. 80S-2001, 80S-2601, 80S-2602, 80S-2501, 80S-2102 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

Supplying, Fabricating & Fixing Aluminium Window 1.5mm thick, 80mm depth Aluminium Framed(max. width 37.6mm) Double Sash(max. width 58.0mm) Sliding Window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately.(Alumex extrusion No. 80S-2002, 80S-2101, 80S-2601, 80S-2501, 80S-2701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-


S07- 333




-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft

1.5mm thick 80mm Double Sashed Aluminium Sliding window with Fixed Panels at Top or Bottom

Supplying, Fabricating & Fixing Natural Anodized Aluminium Window with 1.5mm thick, 80mm depth Aluminium Framed (max. width 48.2mm)and Double Sash (max. width 58.0mm) Sliding Window with Two fixed panels on top or Bottom to the window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80SFL-1002, 80SFL-1003, 80S-2101, 80S-2501, 80S-2601, 80S-2701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

1.5mm thick 80mm Double Sashed Aluminium Sliding window with 2 Fixed Panels at Both Sides

Supplying, Fabricating & Fixing Aluminium Window 1.5mm thick, 80mm depth Aluminium Framed (max. width 66.0mm) Double sash (max. width 55.0mm) Sliding Window with Two fixed panels at sides of the window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80SFL-2102, 80SFL-1003, 80S-2101, 80S-2501, 80S-2601, 80S-2701, 80S-2302 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

1.5mm thick 80mm Double Sashed Aluminium Sliding window with 2 Top Hang Sashes at Top or Bottom

Supplying, Fabricating & Fixing Aluminium Window 1.5mm thick, 80mm depth Aluminium Framed(max. width 48.2mm) Double sash (max. width 58.0mm) Sliding Window with Two Hung panel sashes on top or bottom to the window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80SFL-1002, 80SFL-1003, 80S-2101, 80S-2501, 80S-2601, 80S-2701, 80S-2101 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-


S07- 334




-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft1.5mm thick 80mm 6 Sashed Aluminium Sliding window

-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft

1.5mm thick 80mm 4 Sashed Aluminium Sliding window with 4 Sashes Sliding Panels at Top or Bottom

Supplying, Fabricating & Fixing Aluminium Window with 1.5mm thick, 80mm depth Aluminium Framed (max. width 62.0mm) Four Sliding Sashes(max. width 58.0mm) with Four Sliding panels on top or bottom of the Window including necessary beadings, sliding locks etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80S-2201, 80S-2301, 80S-2101, 80S-2501, 80S-2601, 80S-2701, 80S-2101 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

1.5mm thick 80mm 4 Sashed Aluminium Sliding window with 2 Fixed Panels at Both Sides

Supplying, Fabricating & Fixing Aluminium Window with 1.5mm thick ,80mm depth Aluminium Framed (max. width 63.0mm) Four Sliding Sashes(max. width 55.0mm) with two fixed panels at both sides Window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80S-2201, 80S-2301, 80S-2101, 80S-2501, 80S-2601, 80S-2701, 80S-2101 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-

Supplying, Fabricating & Fixing Aluminium Window with 1.5mm thick ,80mm depth Aluminium Framed (max. width 37.6mm) Six Sashes Sliding Window(max. width 63.0mm) including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80S-2201, 80S-2301, 80S-2101, 80S-2501, 80S-2601, 80S-2701, 80S-2101 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-


S07- 335




S07- 336


Aluminium composite cladding

sq.ftDoor lock for Aluminium Doors

Nos

Nos

Nos

Nos

NosSliding lock for Aluminium door

Nos Stainless Steel Door Handle for Aluminium Doors

NosFloor hinge

Nos

Nos

NosHinges (Stainless Steel) for Aluminium Doors

pairsDoor Closer

Supplying, fabricating and installing of 4.0mm thick Aluminium composite cladding panel (Alucobond or equivalent European make) with open joint tray panel system using non corrosive 50x81x3mm tk. Aluminium "T" channel section (al 217), non corrosive 50x50x3mm pressed Aluminium "U" wall bracket sub frame and AL 201 & AL 202 profiles on tray panel, Rate to include for ss nut and bolts, ss screws, blind rivets, U channels, Nylon resistant, Anchor bolts, and other necessary accessories. Bird mesh to be provided in side of vent areas, all complete as per manufacture's specifications. (8 % attendance fee included)

Supplying and Fixing UNION Door lock (No-X 920,X925 or X930) for Aluminium Door with necessary accessories to working order. ( Prime Cost of a door lock Rs.3380/=)

Supplying and Fixing Door lock (No-VR50101B) for Aluminium Door with necessary accessories to working order. ( Prime Cost of a door lock Rs.5100/=)

Supplying and Fixing Door lock (No-VR50101C) for Aluminium Door with necessary accessories to working order. ( Prime Cost of a door lock Rs.5640/=)

Supplying and Fixing Door lock (Alpha) for Aluminium Door with necessary accessories to working order. ( Prime Cost of a door lock Rs.617/=)

Supplying and Refixing Door lock Cylinder (Alpha) for Aluminium Door with necessary accessories to working order. ( Prime Cost of a door lock Rs.375/=)

Supplying and Fixing Sliding lock for Aluminium door with necessary accessories . ( Prime Cost of a Sliding door Lock Rs.690/=)

Supplying and Fixing Stainless Steel Door Handle for Aluminium door with necessary accessories . ( Prime Cost of a door Handle Rs.1500/=)

Supplying and Fixing of UNION floor hinges (No: 8300) with necessary accessories .(Imported, British or south African make), ( Prime Cost of a floor hinge Rs.21,200/=)

Supplying and fixing imported floor hinges (new star) of approved quality including chipping of existing floors and making good after completion. ( Prime Cost of a floor hinge Rs.16,500/=)

Supplying and Fixing of VVP floor hinges with necessary accessories .(Imported, British or south African make), ( Prime Cost of a floor hinge Rs.9,500/=)

Supplying and fixing UNION Butt Hinges, , 4"x3"x 2mm (thick) stainless steel, for Aluminium doors with pop rivets.


S07- 337


Nos

Nos

Supplying and fixing door closer (new star) with necessary accessories ( Prime Cost of a door Handle Rs.2350/=)

Supplying and fixing door closer (Union or Yale) with necessary accessories ( Prime Cost of a door closer Rs.6424/=)


S07- 338


pairs

pairs

pairs

pairs

pairs

pairs

pairs

pairs

pairsHot dip GI interlocking ceiling frame work only

sq.ftMineral fiber suspended ceiling

sq.ft Mineral fiber Suspended ceiling

sq.ft

Supplying and fixing 8" bar hingers for casement windows with necessary accessories ( Prime Cost Rs.250)






Supplying and fixing Casement Handel (04 hole) for windows with necessary accessories ( Prime Cost Rs.215)

Supplying and fixing Crescent Lock for sliding windows with necessary accessories ( Prime Cost Rs.143)

Supplying and fixing Magnetic Door Catcher (Plastic) with necessary accessories (prime Cost Rs.161)

The frame members for suspended ceiling are in a standard kit (CKM or equivalent). Main runners ( 38mmx24mmx3660mm) are fixed at 1220 centers securely suspended using 4mm dia. GI hanging rod to the structural soffit or timber roof, using an appropriate suspension at 1220mm centers, Cross Tees (27mmx24mmx1220mm) of 1220mm length to be fixed between the main runners at 610mm centers and another cross tees (27mmx24mmx610mm) fixed at mid span between 610mm to form a grid structure of 610mmx 610mm in size. wall angles (24mmx24mmx3050mm) are fixed at wall edges. ( Edge molding and painting paid separately)

Supplying & fixing of 2' 0"x2' 0"& 15mm thick (Mineral fiber) ceiling boards lay on hot dip GI pre engineered interlocking ceiling frame work. The frame members for suspended ceiling are in a standard kit (CKM or equivalent). Main runners ( 38mmx24mmx3660mm) are fixed at 1220 centers securely suspended using 4mm dia adjustable GI hanging rod with spring clips to the structural soffit or existing roof structure, using an appropriate suspension at 1220mm intervals along each Main runners. Cross Tees (27mmx24mmx1220mm) of 1220mm length to be fixed between the main runners at 610mm centers and another cross tees (27mmx24mmx610mm) fixed at mid span between 610mm to form a grid structure of 610mmx 610mm in size. wall angles (24mmx24mmx3050mm) are fixed at wall edges.

Supplying & fixing 4' -0"x 2' -0"x 1/2"thick Mineral fiber ceiling boards lay on Existing interlock type ceiling frame work , forming a panel side of 2' 0" X 2' 0", and at the average elevation of 12' 0" from the working floor, (for 12 nos or 96 ft2)


S07- 339


sq.ft

sq.ftSuper Flex Suspended ceiling

sq.ft

sq.ftGypsum board suspended ceiling

sq.ftMetal ceiling

sq.ft

Supplying and installing mineral fiber Japanese make suspended exposed ceiling system, using 4' 0" x 2' 0"' X 15 mm thick ceiling boards, lay on white colour interlock type, hot dip GI grid system , forming a panel side of 4' 0" x 2' 0"',and suspended on 4mm dia. adjustable rods with spring clip to soffit of concrete or timber roofs. ( Edge molding paid separately)

Supplying and installing mineral fiber Japanese make suspended exposed ceiling (Reveal edge) system, using 605 mm X 605 mm X 15 mm white colour ceiling boards lay on white colour interlock type hot dip GI grid system , forming a panel side of 610mmx610mm,and suspended on 4mm rods with spring clip to soffit of concrete or timber roofs. . ( Edge molding & Painting paid separately)

Supplying and installing Super Flex (Plain) suspended ceiling system, using 4 ft X 4 ft X 3.2 mm ceiling boards lay on white colour interlock type hot dip GI grid system , forming a panel side of 2ft X2 ft , and suspended on 4mm rods with spring clip to soffit of concrete or timber roofs. ( Edge molding & Painting paid separately)

Supplying and installing Super Flex (with design) suspended ceiling system, using 4 ft X 4 ft X 3.2 mm ceiling boards in white colour interlock type hot dip GI grid system , forming a panel side of 2ft X2 ft, and suspended on 4mm rods with spring clip to soffit of concrete or timber roofs ( Edge molding & Painting paid separately)

Supplying and fixing gypsum board suspended ceiling . using 2 ft x 2ft X 9 mm. thick ceiling boards in white colour interlock type hot dip GI grid system , forming a panel side of 610mmx610mm, and suspended on 4mm GI hanging rods with spring clip to soffit of concrete or timber roofs ( Edge molding & Painting paid separately)

Supply and installation of concealed type metal false ceiling, at an average elevation of 12' from the working floor Including revel edge of 2' 0" X 2' 0" size 0.5mm minimum thickness, epoxy powder painted steel Tiles (paint film thickness of average 80microns ) suspended to the roof frame work with, 0.3 mm thick pre painted hot dip galvanized, 15mm x 38mm plain TEE-grid bars and 20mm x 24mm wall angles, suspended with adjustable burrerfly clip, 4mm dia. surface treated galvanized steel hanger rods, complete with necessary anchor bolts and any other accessories. (All in accordance with the approved shop drawings, to the Engineers' satisfaction. )

Prime cost of Concealed type metal false ceiling, 600mm x 600mm size 0.5mm minimum thickness, epoxy powder painted steel Tiles. Rs.790 **(2641)


S07- 340


sq.ft

Partitioning (Gypsum board)

sq.ftRemoving and fixing an Aluminium door Removing existing Aluminium door with frame and fixing at new position. sq.ftAluminium, Ceiling panels (Pinholes)

sq.ftAluminium, partitions with available extrusions

sq.ftRoller Shutter door, Aluminium

sq.ft

Supply and installation of lay in type "E-Metallic Aluminium ceiling, at an average elevation of 12' from the working floor, Including revel edge of 2' 0" X 2' 0"mm size 0.7mm average thickness, 80 microns high quality powder coated Aluminium perforated or plain ceiling panels, suspended to the roof frame work with hot dip galvanized "T" bars of 14mm x 38mm and wall angles of 19mm x 24mm suspended with, adjustable burrerfly clip, 04mm GI hanging roads, anchor bolts and all other accessories. (All in accordance with the approved shop drawings, to the Engineers' satisfaction. )

Prime cost of E-Metallic high quality powder coated Aluminium perforated or plain ceiling Tiles. ( 600mm x 600mm size) Rs.908 **(2641)

Supplying and fixing gypsum board partitioning with GI channel member frame work fixed onto walls and floors , 1/2" thick gypsum board fixed to both sides of frame work complete with making joints using joint tape and gypsum compound to get wall finish. Rate to include for applying one coat of acrylic wall filler to boards.

Supplying, fixing Aluminium 2'-0" x2'-0" ceiling panels (Pinholes) with Aluminium frame work and adjustable. Prime cost of Pinholes Ceiling suspended type 600mm x 600mm size Rs.665

Fixing available Aluminium partition with using new GI channels and new rubber beadings, prop rivets, screws, nails, etc..

Supplying and fixing of a Aluminium Roller Shutter door, having a maximum clear width of 20' and 1.1mm thick Natural anodized Aluminium slats, center bar pulleys, side plates with necessary racers, fabricating mechanical winding box with m.s square tube and covering the box with metallic sheets, fixing on site with bottom bars and G.I, u-channels for vertical guides at two vertical edges, which are painted with two coats of anticorrosive paint and two coats of enamel paint, hard rubber beading embedded in the guide bars to minimize sound & rough flow of the shutter. Pulling rod and chain to be provided for manual rolling operation. (Additional length of 5" to two sides horizontally and 18" to upper end inside the mechanical box as initial winding vertically to be added to the clear opening area). ( 8% attendance fee Considered)


S07- 341


Roller door, Aluminium, Zn/Alu

sq.ftRoller shutter door motor

NosAluminium Fixed Glass Windows

41mm Aluminium Fixed Glass Window Frame Only -DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft

60mm Aluminium Fixed Glass Window Frame Only -DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft

70mm Aluminium Fixed Glass Window Frame Only -DO- Matt Finished Aluminium sq.ft

Supplying and fixing of a Zn/Alu Roller door, having a maximum clear width of 20' and consisting of 0.6mm thick Zn/Al covering sheet, center bar pulleys, side plates with necessary racers, fabricating mechanical winding box with m.s square tube and covering the box with metallic sheets, fixing on site with bottom bars and G.I, u-channels for vertical guides at two vertical edges, which are painted with two coats of anticorrosive paint and two coats of enamel paint to match the colour of door sheeting, and sound reduction rubber beading embedded in the guide bars. Pulling rod and chain to be provided for manual rolling operation. (Additional length of 9" to two sides horizontally and 18" to upper end inside the mechanical box as initial winding vertically to be added to the clear opening area). ( 8% attendance fee Considered)

Supplying roller shutter door motor, 0.5Hp, 300w, 2.5A sing-phase, 1780 rpm and 54:1 gear ratio, with two remote controllers for auto operation. ( 8% attendance fee Considered)

Supplying, Fabricating & Installing of 1.2mm thick 41mm deep Aluminium Fixed Glass window frame only. Rate to include for rawl plugs, fasteners etc. Glass Panels, Louver Panels, paid separately. (Alumex extrusion Nos. CA-1007 or equivalent) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

Supplying, Fabricating & Installing of 1.2mm thick 60mm deep Aluminium Fixed Glass window frame only. Rate to include for rawl plugs, fasteners etc. Glass Panels, Louver Panels, paid separately. (Alumex extrusion Nos. CA-1009 or equivalent)- Refer U001 to U016 for glass & boards, U017 to U051 for louvers-

Supplying, Fabricating & Installing of 1.2mm thick 70mm deep Aluminium Fixed Glass window frame only. Rate to include for rawl plugs, fasteners etc. Glass Panels, Louver Panels, paid separately. (Alumex extrusion Nos. CA-1011 or equivalent)- Refer U001 to U016 for glass & boards, U017 to U051 for louvers-


S07- 342


-DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft

--- The End ---


S07- 343

BSR Rate

A-DEMOLISHER

1,1751,565

1,368

153489

6,956

5,024

556

602

656

696

966

113

170

91616

37580

77333

510



S07- 344

BSR Rate

13

29

290

870

1,305

1,108

1,437

1,823

2,1551,5651,546

387

588

783

1,546

1,827

2,217

5

8

1,100

2,842


S07- 345

BSR Rate

6,526


S07- 346

BSR Rate

115

398

1,752

7,960

15,920

779


S07- 347

BSR Rate

B-EXCAVATOR

1,256

773

1,739

2,705

2,319

1,932

2,874232

7734,810

3,517

1,117

1,310

934

1,407

5,636


S07- 348

BSR Rate

16,541

108

192

216


S07- 349

BSR Rate

C-CONCRETER

36,325

32,482

33,829

36,576

36,563

40,019

564

1,013

43,299

43,556

76

114

639

314

514

216


S07- 350

BSR Rate

283

368

451

375

510

614576

194

210

184

1,721

45,145

46,690

47,463

44,471

46,016

46,789

14,888

19,551

47,170


S07- 351

BSR Rate

47,943

48,715

49,488

48,715

51,807

53,352

15,260

160

117

116

91

233

184


S07- 352

BSR Rate

219


S07- 353

BSR Rate

D-BRICKLAYER41,152

34,393

36,074

16,36512,81013,660

6,65025,171

37,707

19,91937,97759,931

1,392

3,787

619

1,469

253

353

533

271

482

156

697

462


S07- 354

BSR Rate

508

368

293

33,93236,72737,90640,224


S07- 355

BSR Rate

E-MASON

28,59130,523

24,675

14,691

19,520

26,350

17,586

25,310

33,207

56,721


S07- 356

BSR Rate

F-PAVIOR19

43

15,328

11,431

14,433

32,932

1,475

100999594

208

274304

359307318


S07- 357

BSR Rate

352494428440

339333313

483517529

378365

276

378

519

314

293

29,100

294


S07- 358

BSR Rate

211


S07- 359

BSR Rate

332294297292

99240252288288

264

319

314

309

365

387

98104

323

488


S07- 360

BSR Rate

352

460

1,106

1,902

129

1,226

55

280

155

194

374

346


S07- 361

BSR Rate

302

226

342


S07- 362

BSR Rate

G-ROOFER

3,009

33,890

29,550

11,412

28,075

28,584

10,875

13,880

200

35,249

35,883

5,397


S07- 363

BSR Rate

129

33

161

65

160

129

101

179

116

376

325

205

136

153

562

392

2,048

73


S07- 364

BSR Rate

64

89

707,471

387

176

274

49527

27

26

30

2914,684

773580258

7,728

343497748932

298


S07- 365

BSR Rate

374

97

110

266

697

434

566

619


S07- 366

BSR Rate


151

124

51

87

55

30

228

234

160

163

65

38,917

32,892

1,116

6,176


S07- 367

BSR Rate

721,968

12,121

12,571

10,546

13,122

1,660194

34,791

37,303

476

553

551

534


S07- 368

BSR Rate

45

1,119

1,257

170

65

188

231

1,228

936

710

597

1,345

994

1,262

1,079


S07- 369

BSR Rate

715

578

765

621

912

1,212

998

931

738

1,103

635

675

1,410339129

749

3,698

252

224


S07- 370

BSR Rate

749451

893


S07- 371

BSR Rate

532

243

893

798

479

689

2,009

1,549

1,318

1,555

1,330

2,011

891


S07- 372

BSR Rate

831

824

57

93

1,189

969

588

1,087

1,031

133

151

209

910

1,284

62


S07- 373

BSR Rate

62

36

46

405

42,704

30,022

53,462

41,268

753

793

44

136

166

1,001

6118,115

5,745

3,993


S07- 374

BSR Rate

4,979

3,227

34

36

39

4671

100

1,076

851

980


S07- 375

BSR Rate

J-IRONMONGER

6275

114

200

114

121200255293341380

1,439

813

103

362

343

464889

140146

250283

91


S07- 376

BSR Rate

494

2892,316

474

175

47

246

1,081

223

237

252

1,851

443

481

582

677229

896

1,552

2,044

2,754


S07- 377

BSR Rate

638

664

690

821

847

898

1,108

4,326

3,408

440

105

387314279419

1,010

1,300

1,268

1,4931,374

11,580

11,129

1,945


S07- 378

BSR Rate

1,495

109

150

1,153246

165

54

312

240

315

11,580

11,129

776

125

98

215


S07- 379

BSR Rate

382

1,534

1,398

2,279

90,397

92,333

94,660

95,796

97,541

103,916


S07- 380

BSR Rate

106,113

107,165

109,424

112,554

114,952

125,508

109,301

111,832

113,319

115,833

118,331


S07- 381

BSR Rate

K-BRASS FOUNDER

65

255

268

332

320

416383421460540

280

305

357

421

460

486

512

397365391

268

539

318


S07- 382

BSR Rate

286249

638

896

1,352

1,365

1,455

556839

1,352

734

808458

1,762772

451

329302455

365274

1,300

1,139

1,590


S07- 383

BSR Rate

8,299

11,411

2803,0923,993

5,377

8,855

4,899

5,152

4,3962,731


S07- 384

BSR Rate

L-PLASTERER

4,425

5,0693,910

5,3842,802

63

35

86

61

98135

47

224

5,8932871

3,7873,9683,2613,4415,0245,3334,5364,721

663

1,180


S07- 385

BSR Rate

1,180


S07- 386

BSR Rate

5,900

6,827

81

99

8,086

95111


S07- 387

BSR Rate

M-TINKER

354

567

554

2387488

26

388

179

474

427

213

529495

11

1,108

5,032

3,140

3,883


S07- 388

BSR Rate

2,206

262379

733

708

1602,813

487

1,726

1,866

511

339

480

276

539

305

1,200

726


S07- 389

BSR Rate

N-GLAZER

112

182

234

310

220

28


S07- 390

BSR Rate


1,082

194

1,829

1,301

1,610

1,907

21

239

405301

218

384

261


S07- 391

BSR Rate

306

462

501

2,626

2,819

1,648

1,201

1,814

1,984

2,061

4,876

1,356

1,796

1,405

2,553

1,688

2,862

2,013

3,766


S07- 392

BSR Rate

2,362

3,876

2,986

4,593

3,487

3,015

1,748

2,794

2,449

2,562

4,935

3,694

6,410

967

2,808

3,655


S07- 393

BSR Rate

1,3548

15


S07- 394

BSR Rate

1,822

3,413

1,36917

902

1,669

5,302

1,215

3,143

1,797

3,133

2,211

3,944

5,668

4,080

5,804

1,732

6,561

2,164


S07- 395

BSR Rate

6,067


S07- 396

BSR Rate

1021,773

44

200

111


S07- 397

BSR Rate

Q-PLUMBER

290419442

679129

1781,0281,3882,359

3,642278

2,607

5,796

2,639

2,1058,324

23,589

12,526

6,730

1,236


S07- 398

BSR Rate

1,952

2,771

3,655

4,599

6,023

10,621

1,406

2,392

3,774

4,576

5,228

8,646

11,602

18,541

22,492

43,807

2,2152,9864,6258,258

18,22035,111

2,1343,9634,682


S07- 399

BSR Rate

738

1,028

1,202

1,382

1,627

2,174

2,760

1,041

6,238

4,776

7,243

5,947

1,099

3,407

2,634

9,718

108237302


S07- 400

BSR Rate

340533643643900


S07- 401

BSR Rate

2,065

1,516

11,725

8,087

3,671

40,992

43,565

23,540

27,082


S07- 402

BSR Rate

40,786

35,676

38,935

91,099

81,767

83,216


S07- 403

BSR Rate

82,490

45,517

60,895

47,338

59,208

12,710

12,595

4,749


S07- 404

BSR Rate

4,654

1,875

1,981

2,431

4,254

25,192

23,183

3,570

10,255

3,469

23,468

9,490

8,331


S07- 405

BSR Rate


S07- 406

BSR Rate

4,660

1,203

2,607

1,063

3,535

1,359

12,025

13,493

22,638

10,288

31,564

21,904

47,262

40,017

2,430


S07- 407

BSR Rate

6,193

5,410

5,871

5,281

3,494

3,182

4,323

13,452

23,379

47,182

8,325

25,209


S07- 408

BSR Rate

29,047

9,968

11,774

21,641

21,262

21,987


S07- 409

BSR Rate

43,118

20,779

28,024

8,386

4,982

5,111

9,411

20,581


S07- 410

BSR Rate

23,801

9197

140

516

580

966

2,898

3,156

825

10138

117230

819

2,494


S07- 411

BSR Rate

2,853

3,279

308

372

408

503

393

434

4,533

989

1,300


S07- 412

BSR Rate


S07- 413

BSR Rate

2,575

2,008

546

531

4,652

1,2701,174

2,019

421

497

614

497


S07- 414

BSR Rate

771

858

1,934

1,981

381

426

236

2,137

3,779

2,523

822

1,2051,5652,0812,725


S07- 415

BSR Rate

3,6585,7472,531

294294332525603757796139177

3,2851,868

173211263353372469

610

4,6731,704

6,408

1,393

993

2,696

335605

1,569

2727293335


S07- 416

BSR Rate

13

11915722226129941529

14517323527331240954

161

204

233

315

343

467

573

775

34

46


S07- 417

BSR Rate

2586

46

63

63757

25

93719

174200238290406444

14318221424731137548116919223425930737153

11,841

3,269


S07- 418

BSR Rate

4,948

3,761

4,060

471858

1,282

8,952

10,614

18,677

19,901

14,980

24,902

46,394

89,774

156,911


S07- 419

BSR Rate

2,898

199224256347475701

2,7463,4674,2326,0783,446

20,346

1,203

817

6,777

2,882

6,200

851


S07- 420

BSR Rate

1,674

4,224

3,231

946

2,798

2,437

3,625

4,720

9,292

92


S07- 421

BSR Rate

446453453525

636

2,710


S07- 422

BSR Rate

2,973

2,174

4,634

194290

39

7388

105185271417

1,730

587888

114180232619

6983

116

163185

216

8898

152

225


S07- 423

BSR Rate

353541

1,688

627588

116154231637

658083

127152185522

587083

107141172522

683748

1,2632,1002,7443,5813,903

361

490

490

812

966


S07- 424

BSR Rate

1,714

2,473


S07- 425

BSR Rate

6488

111160243304842

677671

109137186666627588

116154231653

20

47

100

131

171

275

784

26

35

45


S07- 426

BSR Rate

70

87

25

59

121

160

209

339

228274326519567

364

339

674

1,2682,537

4,140

6,10928,233

51,249


S07- 427

BSR Rate

921

33,025

30,024

20,684

23,338

33,951

207427

9,773

377

561

323

351

240


S07- 428

BSR Rate

198

142


S07- 429

BSR Rate

R-DRAIN LAYER

4,5835,695

976

10,311

17,334

28,591

12,771

17,744

20,902

26,721

14,436

18,938

22,058


S07- 430

BSR Rate

27,387


S07- 431

BSR Rate

19,440

22,189

26,317

27,868

1,372

11,053

23,271

206

355419

483612

677

963

739

884

673

963979


S07- 432

BSR Rate

1,088

1,167

1,286

1,126

1,027

393

480

555

858537

592

689

786

545

704

362

435

369

435

480

513

580


S07- 433

BSR Rate

536

514

589

275

354

605

698

735

911

952

1,074

1,446

1,489

1,609


S07- 434

BSR Rate

4,085


S07- 435

BSR Rate

S-MISCELLANEOUS

76

9427325

18,219

36,741

39

24

1,127

11

11

11

11

14

4

4


S07- 436

BSR Rate

4

5

247

1,395

1,731

8,668

346578

448

232

310

387

1,361

157

186

13


S07- 437

BSR Rate

356


S07- 438

BSR Rate

421

666

114

55

5,1525,1524,6374,6374,6374,6379,145

6,7625,1523,7363,7363,7363,736

355355451838548

1,932

5,861

6,634

7,922

7,922

1,127


S07- 439

BSR Rate

1,623

2,709

1,621

3,910

1,161

773902

1,031

1,160

20222123

49

5

4

61


S07- 440

BSR Rate



S07- 441

BSR Rate

3,6973,8933,8005,9573,8804,085

5,3816,136

8,277

4,1724,3684,2746,6564,3544,547

5,8456,7088,984

13,916

15,628

18,153


S07- 442

BSR Rate

20,321

22,582

24,588

18,183

19,895

22,875

25,137

27,683

29,396

31,957

50,319

56,518

93,214

22,691

3,452

4,224

9,613

10,523

6,719

9,297

14,426


S07- 443

BSR Rate

17,288


S07- 444

BSR Rate

227507520855

1,3882,0372,980

627950

1,3552,2083,1624,9226,314

661813

1,4871,9032,5605,8142,0632,9804,707

7,4258,548

10,93414,09318,65622,23627,290

247507606946

1,398


S07- 445

BSR Rate

2,0733,291

7091,0961,5852,5763,5545,1756,838

6,056

1,0681,675

10,226

7,430

13,415

16,320

14,339

8,5313,813

5,796

2,384

6,852

6,483

9,784

6,852

9,784


S07- 446

BSR Rate

6,483

7,536

6,2494,629

782809905

376524710980

1,1781,3471,6051,643

6451,956

8,752

8,531

8,531

9,460

10,853

12,027

642229


S07- 447

BSR Rate

617207

8796

109164212277

7682

213263271524515

1,020531

1,0571,2091,3241,4801,7812,2343,1223,711

1,0941,2361,4311,630

20,16625,721


S07- 448

BSR Rate

U-ALUMINIUM FABRICATOR

194

322

22

293

322

341

370

122


S07- 449

BSR Rate

151


S07- 450

BSR Rate

141

171

170

200

148

178

258

9391,0021,0371,1421,650

878972991

1,107


S07- 451

BSR Rate

1,391


S07- 452

BSR Rate

1,2361,3751,4031,5752,067

1,2591,3291,3531,5212,062

862913929

1,0441,412

847723

1,0042,476


S07- 453

BSR Rate

776


S07- 454

BSR Rate

1,5871,3281,9034,9171,420

272282284301359

389412418447570


S07- 455

BSR Rate

289303307326415

243251254268310


S07- 456

BSR Rate

270281284299362

351371377402507


S07- 457

BSR Rate

240249251264318

292307310329413


S07- 458

BSR Rate

245256259273342

256264266281321

333352356389419


S07- 459

BSR Rate

285296299316374

422452458506549

310323


S07- 460

BSR Rate

326343


S07- 461

BSR Rate

413

496535541601650

384403409432534

660717727812886


S07- 462

BSR Rate

256268271286351

429464470526571


S07- 463

BSR Rate


S07- 464

BSR Rate

228237239251300

350376380422456

294310314333419

530578586660721


S07- 465

BSR Rate

235246249263333

426464471533578

383391397425525


S07- 466

BSR Rate

362386390420458

9651,0441,0631,1781,492

638691707759907


S07- 467

BSR Rate

1,0371,1381,1521,2341,492


S07- 468

BSR Rate

1,0621,1651,1781,2621,518

928947954998

1,053

869895899931971


S07- 469

BSR Rate

487507514561615

615668687736962

448471478522644


S07- 470

BSR Rate

466485489516638

460495501545671

728790801878

1,091


S07- 471

BSR Rate

733798810890

1,097


S07- 472

BSR Rate

748846860

1,0631,131

848904907

1,0111,232

837949964

1,0611,272


S07- 473

BSR Rate

840939954

1,0421,284

677676686755920

695756767842

1,015


S07- 474

BSR Rate

744777801883992

852907921

1,0161,167

882943

1,0371,0581,202


S07- 475

BSR Rate

879938952

1,0511,209

880941

1,0291,0271,182

886953

1,0251,0491,204


S07- 476

BSR Rate

364378383413518

456476482518659

515535541574715

446470478515678

341354358386488

403


S07- 477

BSR Rate

422428462600

347365371402532

426449456491648

328341345372472

401419425458595

367384390419543

418439446480633


S07- 478

BSR Rate

326338342368468

392411417449586

358374379408528

411432439473622

443475487522661

525562575


S07- 479

BSR Rate

616787

557592602639798

481519530571749

393421430462586

446480490528685

386417427462608

456493503542711


S07- 480

BSR Rate

371398406437555

435468477514665

403433442475614

445480489528692

364390397427544

422455463500649

392421429462


S07- 481

BSR Rate

596

437471480518678

551594595659851

644694699766995

666711719774984

600650662719953

501540


S07- 482

BSR Rate

544597773

567613622678891

494536545596794

578625638692917

479517523571742

556601611663872

511552560610800


S07- 483

BSR Rate

566613625677897

472509515562730

543587598649855

500540548596781

558604616668884

648676686


S07- 484

BSR Rate

741944

689717727788996

668690698742919

574597605655838

578602611657841

592615624677866

510531539582756


S07- 485

BSR Rate

558580588637817

550572581624802

574596605655838

536556564606778

552573581629807

539561569611785

558580588637


S07- 486

BSR Rate

817

530550559599770

547568576624800


S07- 487

BSR Rate

675739760833

1,056

735806829906

1,166

695760781851

1,092

668710717768888


S07- 488

BSR Rate

811822832897

1,085

1,0911,1691,1871,2971,550

1,3511,4601,4841,6301,992


S07- 489

BSR Rate

1,4761,6001,6271,7922,208

653710722800897

515526529542579


S07- 490

BSR Rate

575591596616673

598620626653728

579596600620671


S07- 491

BSR Rate

19631635660714

578619626676810

686738748813985


S07- 492

BSR Rate

855809820895

1,090

872926936

1,0021,144

828885897


S07- 493

BSR Rate

9781,189

698751761827999

766829841918

1,042

767828839


S07- 494

BSR Rate

9151,086


S07- 495

BSR Rate

1,300

5,265

6,836

7,531

1,062

750

1,068

2,106

28,364

22,613

13,294

2,134


S07- 496

BSR Rate

3,602

8,647


S07- 497

BSR Rate

446

481

562

654

884

1,254

458

365

332

202

273

146


S07- 498

BSR Rate

408

468

184

192

367

574


S07- 499

BSR Rate

616

559

96

451

102

786


S07- 500

BSR Rate

786

38,640

381405412448594

445482496535710

536


S07- 501

BSR Rate

584588651873

BSR 2014- Department of Buildings1

Esti Rana / BSR 2014 S0 7 - 194

A-DEMOLISHER

B-EXCAVATOR

C-CONCRETER

D-BRICKLAYER

E-MASON

F-PAVIOR


Esti Rana / BSR 2014 S0 7 - 195

G-ROOFER


J-IRONMONGER


Esti Rana / BSR 2014 S0 7 - 196

K-BRASS FOUNDER

L-PLASTERER

M-TINKER

N-GLAZER



Esti Rana / BSR 2014 S0 7 - 197

Q-PLUMBER


Esti Rana / BSR 2014 S0 7 - 198


Esti Rana / BSR 2014 S0 7 - 199

R-DRAIN LAYER


Esti Rana / BSR 2014 S0 7 - 200

S-MISCELLANEOUS


U-ALUMINIUM FABRICATOR


Esti Rana / BSR 2014 S0 7 - 201


Esti Rana / BSR 2014 S0 7 - 202

Maintenance BSR for 2014

Department of Buildings, Sethsiripaya, Battaramulla.

INDEX

A-DEMOLISHERChipping lime plastering Roof removing Demolishing rubbleRemoving and stacking tilesRemoving water proof, asbestos ceiling &Valance or Barge boards.Chipping cement plasterTransporting debrisPreparatory workFelling Trees Removing Top Soil

B-EXCAVATORFilling Under floors & foundationsEarth work supports

C-CONCRETERConcreting Mass (Gr.15 Mix)Concreting Drains (Gr.15 Mix)Concrete (Grade 20 Mix)Curbs Concreting Drains, semi-circularConcreting Lintols (Gr. 20 Mix)Slabs over drainsConcreting of Beams and Columns (Gr. 20 Conc)Concreting Slabs (Gr. 20 Mix)Concreting Structural Elements (Gr. 25 Mix)Ready mixed ConcreteForm work (Untreated Non-structural Category A)Form work (Using Timber planks)Plywood form work (20mm thk.)

D-BRICKLAYERBrickwork in (1:5) cement mortar Brickwork Wire cut)Brickwork in (1:8) cement mortar

E-MASONRandom RubbleCellular (Hollow) block masonrySolid block masonryPaste rubble masonry

F-PAVIOR

Floors, gravel Floor tiles (Laying only)Tiles- pressed

Floor tiles- Porcelain glazed (Non homogeneous)Floor tiles- Vitreous Porcelain ( Homogenous)-LocalFloor tiles- Polished Porcelain ( Homogenous)-LocalFloor tiles- Rustic Type ( Homogenous)-LocalFloor tiles- (Approved quality)Terrazzo tile flooringTerracotta tilesWall tiles -glazed ( Approved Quality)

Floor tiles- Ceramic Non-skid ( Approved quality)Floor tiles- Ceramic glazed (Non homogenous)-Local

Wall tiles -Local


Esti Rana / BSR 2014 S0 7 - 203

INDEX

Wall tiles (Fixing only)Border Tiles for Wall (Decorative)

Glass blockPVC carpeting Loop pile carpeting Cut pile carpeting Interlocking pavingPaving tile Slabs

G-ROOFERCorrugated sheetsCorrugated Aluminium sheetsCorrugated Asbestos SheetsCorrugated Asbestos "Colorup" SheetsZinc Aluminium Sheet RoofingCorrugated galvanized iron Sheet RoofingLeaks -on roofsRidgingZinc Aluminium ridge capping Skylight glassTiles, calicut pattern, flatTiles half round Structural Steel Purlins for RoofHigh tensile Galvanized steel, C-channel purlins for Roof Heat and Sound installation (Double side luminary Aluminium foil)Timber Members for Roofing

H-CARPENTER & JOINERBoards, barge, valance, fasciaCeiling / PartitionPartitionsTimber PlugsPlywood PanelsCove, mouldingsDoors or windowsDoor framePlywood Door Doors or windows framing and battening sashDoors glazing and/or paneling Door or Window frame Fillets, quadrant Timber GateLouver bladesWooden Posts Reepers, timber Roof with sawn timber framework & Covering Tiles on itShelvingSkirting Other Carpentry work. TrellisPantry cupboards units

J-IRONMONGERBolts and Nuts, IronIron BracketsWeld meshCabin HooksCasement StaysChimneyGate, Iron

Granite flooring-Local


Esti Rana / BSR 2014 S0 7 - 204

INDEX

Gutter HooksHasp and stapleHinges (Iron)Hinges (Stainless Steel) for Timber DoorsHoldfastLocks (iron)Mild steel rodsWire mesh Reinforcement, with Tor steel rodsChain-link fencingMild Steel Grill work Guard rails ( Heavy duty GI-Pipe)Hand rails ( Heavy duty GI-Pipe) Hand rails (Stainless Steel, 1.5mm thick Pipe- Grade 304 )Web Truss

K-BRASS FOUNDERBolts, barrel, brassCabin Hooks (Brass)Casement fasteners, brassHasp and staple, brassHinges, brassLocks (Brass)

L-PLASTERER

MouldingRendering CementCement floating coat.Cement Rendering and smooth Coloured floating coatRendering Cement with PudloSkirting in cement mortarD.P.C- 3/4"

M-TINKERGI-Down pipes / Hold fastsG.I FlashingZn/Al-FlashingG.I semicircular GuttersValley gutter (G.I)Zinc Aluminium Colour bonded valley gutter (0.47mm) Zn/Alu high tensile down pipes Zn/Alu gutters Zn/Alu Down pipe Bends

N-GLAZER


Skim coatCement washing to wallsWhite or colour washing wallsSnowcem paintAcrylic wall Filler ( Primer for Interior)Alkali resisting primerElastometic filler PrimerAlkali resisting water Proofing sealerHeat Resistant paintSilicone masonry water repellent paint

Plastering (walls) Plastering (beams, slab soffits)

Plastering (Reveals)

Surface preparation (Old work) for Painting (Scraping /Patching /Smoothing)


Esti Rana / BSR 2014 S0 7 - 205

INDEX

Bathroom paintEmulsion paint (Interior)Painting General Purpose weather shied ( Exterior)Painting on old work with General Purpose weather shied (Exterior paint)Painting on New work with, Two Coats of Acrylic Emulsion weather shied Acrylic Emulsion (Exterior paint)Painting asbestos sheet roofFloor PaintingAnticorrosive paintPainting on GI SurfaceAluminium paintEnamel paintRemoval of Paint from timber. Wood preservative Enamel paint with Wood primer Under coatPolishing wood work with WaxPainting with Wood sheenPolyurethane Varnishing polyurethane varnish-MattRemoving VarnishPainting with Sanding sealer / Woof finish LacquerPainting with Perque varnishPainting Letters on (Board / Wall)

Q-PLUMBERBall valve-UPVCBall valve-BrassConcealed Taps/Valves-Chromium platedFlush valveFlush valve to existing Urinal (Imported )Gate valve brass imported (English or equivalent, approved quality).Float valueFoot value Lavatory BasinRemoving bath room FittingsCloset-pedestal typePlastic seat cover, imported

Close coupled water closet suite (colour) Close coupled European type low level commode suit (white ) Bidet, pedestal type-ImportedBidet, pedestal type, Manufactured in Sri Lanka.Bath wear set (3-Pieces)-Fixing OnlyCloset-squatting typeRemoving Closet-squatting typeFixing available Closet-squatting typeSquatting pan- EuropeanSquatting pan Ceramic ( Indian)Closet squatting type ( Indian or equivalent)Cistern high level (Plastic)- ( Indian or equivalent)Cistern high level, ceramic-(Twyford or equivalent approved quality)Cistern, high level, auto flush-CeramicCistern, high level, auto flush-PlasticCistern low level, flushing- porcelain (Indian , approved quality).Syphon Magic Bend Urinal(Indian)

Close coupled water closet suite (white) -ImportedClose coupled water closet suite (white)-Manufactured in Sri Lanka.


Esti Rana / BSR 2014 S0 7 - 206

INDEX

Urinal Imported- TwyfordSink and fittings-Fixing OnlySinkReplacing SinkStainless steel kitchen sinkWash Basin Wash Basin (local Bath wear)Corner wash basin (Imported quality)Corner wash basin (Indian, approved quality)Vanity basinRubber plugsWooden plugsBottle traps PVC P-Trap (2" dia.) Fixing and Repairing , available TapsBib Taps (Metallic)Bib Taps (Plastic)Swan-Neck tap-(Metallic)Swan-Neck tap-(Plastic)Chromium plated angle Taps/Valves 1/2"Angle Taps/Valves (Plastic)Chromium plated basin tap 1/2"Push tapsStop tap. (Imported approved quality)Stop Taps (Plastic)Bath tub tapGarden Taps (brass)Garden Taps (Plastic)Pillar cocksPillar tapsBasin Piller Taps (Plastic)Stop cockConnector, G.IElbow, G.IHooks for pipesJam NutsNipples, G.IPipes G.I Socket G.I R.S.J 's as supports for tanksRemoving tank G.I Fixing tank, G.IClearing & washing tankPlastishell (Single Layer) water tank Plastishell (Triple Layer) water tank Floater switchTeesTrapsBath room accessories (Total Set) Tumbler holderSoap tray/dishSoap dispenserShelves, plate glass Towel rail Paper holder SEVATooth brush holder


Esti Rana / BSR 2014 S0 7 - 207

INDEX

Robe hook (SEVA)Bath room mirror,Shower rose-Fixing OnlyShower rosePlastic Jet Shower roseShower headBidet spray importedAccessoriesFixing bends, elbows and tees- Workmanship onlyBends P.V.CElbows P.V.CReducing sockets & Tees P.V.CReducing Tees P.V.CRepair Sockets & Tees P.V.CValve Socket P.V.CFaucet Socket P.V.CTapered union without thread P.V.C Equal tees-P.V.CPlugs, sockets-P.V.CPipes P.V.CFixing pipesPipes P.V.C (25% pipe cost included for Specials)Flexible cord (S--Lon or Equivalent))Flexible cord (Imported European)Flexible hoseGarden Watering Hose ½" dia.Water pumpElectric water geyserPlastic gullyShower tray fiberglassElbows for down pipe. Running head. Gutter end.Gutter Joint.Eves gutters (PVC)-Square typeDown pipes 3½" dia. P.V.C

R-DRAIN LAYERInterceptor, EarthenwareManhole- brick in cement

Manhole cover, reinforced concreteManhole cover, Cast IronCast iron gratingWire dome (Steel)Wire dome (Copper)Drainage Fittings 4" (110mm) dia-(Local make)Drainage Fittings 2" (63mm) dia.Drainage Fittings 1½"or (50mm) diaPipes P.V.C, 4"(110mm) dia, (type 250)-(Vent pipes fixed to walls)Pipes P.V.C, 4"(110mm)dia, (type 400)-(Vent pipes fixed to walls)Pipes P.V.C, 4"(110mm) dia, (type 400)- lay in TrenchesDrain Pipes P.V.C, 4" dia, (type 600)- lay in TrenchesDrain Pipes P.V.C, 6" dia, (type 600)- lay in TrenchesDrain Pipes P.V.C, 12" dia, (type 600)

RCC Manhole (Type A)- [As per Drg.No 2013-TP-ST06 & ST07]RCC Manhole (Type B)- [As per Drg.No 2013-TP-ST06]RCC Manhole (Type C)- [As per Drg.No 2013-TP-ST06]


Esti Rana / BSR 2014 S0 7 - 208

INDEX

S-MISCELLANEOUS Scaffolding of BamboosSteel scaffolding SetsGarden lampFencingWell, bailing out waterWater proofing (Treatment)Water proofing (Membrane)Timber treatmentDoor PVCLandscapingLaying turf sodsPalm treesMixed FlowerRoad ConstructionProviding Labour Services Flagging

T-ELECTRICAL INSTALLATIONSIn PVC conduitIn PVC conduitIn PVC CasingIn PVC CasingDistribution BoardsCabling in conduitsCabling in PVC CasingEarth Electrode Luminaries and FixturesSwitch socket outletReplacing sunk switchFansExhaust FansWall FansFluorescent LampConduit PipePVC CasingCommissioning Wires Commissioning Earth Wires Supply & Installation of Dol Starter

U-ALUMINIUM FABRICATORBoards and Glass PansTypical Aluminium LouversAluminium SUN Louvers with Louver Frame (Alumex ALU 180 or equivalent)

Single Row Aluminium Partition Frame Work with Boards/GlassSingle Row Aluminium Partition Frame Work with Louvers2 Row Aluminium Partition Frame Work with Boards/Glass2 Row Aluminium Partition Frame Work with Louvers & Boards/Glass3 Row Aluminium Partitions 3 Panel Aluminium Louver Partitions Aluminium 76mm Shopfront Aluminium 100mm Shopfront Aluminium Curtain Wall (2.0mm thick)Aluminium Curtain Wall (1.5mm thick)Aluminium doors

Aluminium SUN Louvers (Alumex ALU 180 or equivalent) with BIRD'S MOUTH BRACKETS (Alumex ALU 282 or equivalent)


Esti Rana / BSR 2014 S0 7 - 209

INDEX

Door Outer frames Aluminium Sliding DoorsAluminium Casement WindowsCasement Window Frames Only Aluminium Casement & Pivot Window (Frame Only)Casement Window Sash Only Aluminium Sliding windowsAluminium composite claddingDoor lock for Aluminium Doors Sliding lock for Aluminium doorHinges (Stainless Steel) for Aluminium DoorsHot dip GI interlocking ceiling frame work only(Mineral fiber / Stone wool) acoustic ceiling suspended ceiling Mineral fiber acoustic Suspended ceilingSuper Flex Suspended ceilingGypsum board suspended ceilingMetal ceilingPartitioning (Gypsum board)Aluminium, Ceiling panels (Pinholes)Aluminium, partitions with available extrusions Roller Shutter door, AluminiumRoller door, Aluminium, Zn/Alu Aluminium Fixed Glass Windows


Esti Rana / BSR 2014 S0 7 - 210

Item Start From

S07-25A026A029A032A035A038A043A044A046A047A051

S07-28B016B019

S07-30C001C007C009C014C015C016C024C028C034C036C043C046C049C051

S07-33D002D010D028

S07-35E001E004E007E010

S07-36

F007F008F012F013F015F018F022F025F028F030F035F037F038F047


Esti Rana / BSR 2014 S0 7 - 211

Item Start From

F053F055F059F062F063F066F067F069F071

S07-41G001G002G005G008G009G010G013G019G027G029G030G040G049G053G055G056

S07-45H007H012H026H033H034H035H037H067H069H073H076H080H082H084H089H092H095H100H104H107H109H116H125

S07-53J001J013J014J017J022J024J032


Esti Rana / BSR 2014 S0 7 - 212

Item Start From

J033J034J037J053J055J057J066J075J079J081J085J086J086J088J089

S07-59K002K011K018K023K026K039

S07-62L001L004L009L017L025L028L029L030L032L033

S07-64M001M008M010M011M031M032M034M036M038S07-66

S07-67P003P007P008P011P017P020P021P022P023P024P025


Esti Rana / BSR 2014 S0 7 - 213

Item Start From

P026P027P031P033P035P037P038P042P046P048P049P052P054P056P058P060P061P063P066P068P069P072P074

S07-72Q001Q006Q012Q015Q018Q020Q037Q043Q052Q058Q070Q074Q075Q077Q087Q088Q089Q090Q092Q093Q094Q095Q098Q100Q101Q102Q103Q104Q105Q106Q107Q109Q110


Esti Rana / BSR 2014 S0 7 - 214

Item Start From

Q112Q120Q121Q125Q127Q131Q134Q143Q144Q146Q148Q150Q151Q156Q157Q161Q165Q171Q172Q174Q176Q178Q179Q181Q182Q188Q189Q190Q192Q194Q196Q197Q204Q215Q231Q237Q244Q251Q276Q290Q291Q293Q295Q298Q302Q307Q308Q314Q319Q320Q321Q324Q325Q326Q328Q329


Esti Rana / BSR 2014 S0 7 - 215

Item Start From

Q331Q332Q335Q336Q340Q342Q343Q345Q347Q348Q355Q362Q368Q375Q382Q389Q396Q410Q417Q437Q438Q443Q449Q454Q456Q457Q459Q463Q469Q471Q472Q473Q474Q475Q476Q478

S07-98R001R004R007R011R015R019R020R022R023R025R027R039R049R059R060R061R064R067R070


Esti Rana / BSR 2014 S0 7 - 216

Item Start From

S07-102S006S008S010S011S027S031S033S034S035S038

S046S052S058S068S072

S07-106T001T007T010T016T019T044T074T088T089T109T112T122T123T127T128T132T138T147T155T159

S07-113U001U017U042U047

U052U062U067U082U097U137U177U182U187U192U197


Esti Rana / BSR 2014 S0 7 - 217

Item Start From

U207U242U312

U632U647U677U742U743U748U753U765U766U767U770U772U773U775U777U778U779U780U782

Rate per sq.ft76mm extrusions 100mm extrusions

Al. Partitions MF NA BA PC WF MF NA BA PC WF

Fully board (2 row) 7 ft height 597 605 608 622 664 N/A N/A N/A N/A N/A

Glass & board (2 row) 7 ft height 491 502 505 520 583 N/A N/A N/A N/A N/A

Fully board (3 row) 10 ft height 610 618 620 635 675 687 706 710 743 773

Board, glass & board (3 row) 10 ft height 546 557 560 577 635 683 713 719 767 810

781 835 846 913 1126 954 1031 1045 1153 1346

Swing Doors (Excluding lock, door closer)76mm 100mm - 1.6mm tk

MF NA BA PC WF MF NA BA PC WF

1673 1792 1811 1933 2233 2030 2149 2167 2287 2587

1693 1812 1831 1953 2253 2050 2168 2187 2307 2607

1516 1628 1645 1751 2034 1730 1842 1858 1964 2246

1535 1648 1664 1771 2053 1749 1862 1878 1983 2266

window41mm 60mm

MF NA BA PC WF MF NA BA PC WFTwine sash fully glass casement window 1160 1215 1226 1305 1527 1212 1282 1298 1381 1625Fixed glass window 532 556 563 599 745 596 633 647 686 861Fixed louvered window 1617 1780 1815 2023 2661 1681 1857 1899 2110 2777

100mmMF NA BA PC WF

899 997 1011 1214 1282

80mmMF NA BA PC WF

Board, glass & "y" type louver (3 row) 10 ft height

Single sash swing door with top glass & bottom fabric

Single sash swing door with top glass & bottom both side coloured cladding board

Double sash swing door with top glass & bottom fabric

Double sash swing door with top glass & bottom both side coloured cladding board

100mm double sash Sliding Door (One sash fixes) fully glass excluding lock, handles

80mm double sash sliding window (both sash sliding) fully glass

837 889 899 964 1136

80mm double sash sliding window (both sash sliding) fully glass

70mm (1.2mm thick)MF NA BA PC WF1320 1401 1412 1516 1812

687 735 739 802 10241772 1959 1991 2226 2940

Date post:	10-Jul-2016
Category:	Documents
Upload:	madusha-galappaththi
View:	424 times
Download:	90 times

BSR 2014.xlsx

Documents