Date post: | 15-Aug-2015 |
Category: |
Engineering |
Upload: | technos-inc |
View: | 111 times |
Download: | 5 times |
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
SN PROJECT
CODE
PROJECT TOPIC YEAR
01
EMB_2015_01
Topic: Multirobot Control Using Time-Varying Density Functions
Abstract: An approach is presented for influencing teams of robots by means of time-varying density functions,
representing rough references for where the robots should be located. A continuous-time coverage algorithm is proposed and distributed approximations are given whereby the robots only need to access information from
adjacent robots. Robotic experiments show that the proposed algorithms work in practice, as well as in theory.
2015
02
EMB_2015_02 Topic: Wall-Following Control of a Hexapod Robot Using a Data-Driven Fuzzy Controller Learned
Through Differential Evolution
Abstract: This paper proposes the use of evolutionary fuzzy control for a wall-following hexapod robot. The
data driven fuzzy controller (FC) is learned through an adaptive group-based differential evolution (AGDE)
algorithm, which avoids the explicit usage of the robot mathematical model and time-consuming manual design effort. In the wall following task, the inputs of the FC are measurements of three infrared distance sensors
mounted on the hexapod robot. The FC controls the swing angle changes of the left- and right-middle legs of the
hexapod robot for proper turning performance while simultaneously moving forward. To automate the design of the FC and to improve the performance of control, an AGDE algorithm is proposed. In the AGDE-designed FC,
a cost function is defined to quantitatively evaluate the learning performance of an FC based on data generated
online. In the AGDE, the solution vectors in a population are adaptively clustered into different groups based on their performances at each iteration. To improve optimization performance, the AGDE adaptively selects
components from either the group-based mutant vector or a typical population-based mutant vector in the
mutation operation. Simulated and experimental results are gathered to verify the effectiveness and efficiency of the data-driven AGDE-based learning approach.
2015
03
EMB_2015_03
Topic: A Sensor-Based Dual-Arm Tele-Robotic System
Abstract:We present a novel system to achieve coordinated task-based control on a dual-arm industrial robot for
the general tasks of visual servoing and bimanual hybrid motion/force control. The industrial robot, consisting of a rotating torso and two seven degree-of-freedom arms, performs autonomous vision-based target alignment of
both arms with the aid of fiducial markers, two-handed grasping and force control, and robust
object manipulation in a tele-robotic framework. The operator uses hand motions to command the desired position for the object via Microsoft Kinect while the autonomous force controller maintains a stable grasp.
Gestures detected by the Kinect are also used to dictate different operation modes. We demonstrate the
effectiveness of our approach using a variety of common objects with different sizes, shapes, weights, and surface compliances.
2015
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
04
EMB_2015_04
Topic: Automated Health Alerts Using In-Home Sensor Data for Embedded Health Assessment
Abstract: We present an example of unobtrusive, continuous monitoring in the home for the purpose
of assessing early health changes. Sensors embedded in the environment capture behavior and activity patterns. Changes in patterns are detected as potential signs of changing health. We first present results of a preliminary
study investigating 22 features extracted from in-home sensor data. A 1-D alert algorithm was then implemented
to generate health alerts to clinicians in a senior housing facility. Clinicians analyze each alert and provide a
rating on the clinical relevance. These ratings are then used as ground truth for training and testing classifiers.
Here, we present the methodology for four classification approaches that fuse multisensory data. Results are
shown using embedded sensor data and health alert ratings collected on 21 seniors over nine months. The best results show similar performance for two techniques, where one approach uses only domain knowledge and the
second uses supervised learning for training. Finally, we propose a health change detection model based on these
results and clinical expertise. The system of in-home sensors and algorithms for automated health alerts provides a method for detecting health problems very early so that early treatment is possible. This method of passive in-
home sensing alleviates compliance issues.
2015
05
EMB_2015_05 Topic: Security-Aware Modeling and Efficient Mappingfor CAN-Based Real-Time Distributed
AutomotiveSystems
Abstract: Security has become a critical issue for automotive electronic systems. To protect against attacks,
security mechanisms have to be applied, but the overhead of those mechanisms may
impede system performance and cause violations of design constraints. To remedy this problem, we proposed an integrated mixed integer linear programming (MILP) formulation that is the first to
address both security and safety constraints during system mapping for controller area network (CAN) based
systems [10]. However, its signal-based security constraints do not fully reflect real security requirements, and its
objective function is to minimize functional path latencies rather than minimize security risk. Furthermore, its
MILP-based approach has high computation complexity.
In this work, we present a new formulation that defines path-based security constraints and minimizes security risk directly, and propose a new heuristic algorithm to solve the formulation efficiently. Experiments on an
industrial example show that our new algorithm achieves comparable solution quality as the MILP-based
approach with much better efficiency.
2015
06
EMB_2015_06 Topic: Design and Operation of Secure Cyber-Physical Systems
Abstract: This letter proposes a holistic framework for the design and operation of secure and reliable resource-
constrained cyber-physical systems. The proposed framework combines
control-theoretic methods, information security notions and computational models to characterize tradeoffs among different design and operation objectives. We quantify the intricate relation among control performance,
system security and platform schedulability through a minimal set of interface variables. We argue that security
2015
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
mechanisms and control algorithms need to be codesigned and comanaged with the embedded platform, so as to avoid the design of algorithms that are too
expensive to implement on the embedded platform, or significantly impede
design objectives such as performance and timing robustness.
07
EMB_2015_07 Topic: Visual Servo Control Part I: Basic Approaches
Abstract: This article is the first of a two-part series on the topic of visual servo control using computer vision
data in the servo loop to control the motion of a robot. In the present article, we describe the basic techniques that
are by now well established in the field. We first give a general overview of the formulation of the visual servo
control problem. We then describe the two archetypal visual servo control schemes: image-based and position-based visual servo control. Finally, we discuss performance and stability issues that pertain to these two schemes,
motivating the second article in the
series, in which we consider advanced techniques.
2015
08
EMB_2015_08 Topic: A Wearable Robot for the Hand with a Soft Tendon Routing System
Abstract: oft wearable robots are good alternatives to rigid-frame exoskeletons because they are compact and
lightweight. This article describes a soft wearable hand robot called the Exo-Glove mechanism. The proposed
system can be used to develop other types of soft wearable robots. The glove part of the system is compact and weighs 194 g. The results that uses a soft tendon routing system and an underactuation adaptive
conducted using a healthy subject showed sufficient performance for the execution of daily life
activities, namely a pinch force of 20 N, a wrap grasp force of 40 N, and a maximum grasped object size of 76 mm. The use of an underactuation mechanism enabled the grasping of
objects of various shapes without active control.
2015
09
EMB_2015_09 Topic: Comparison of On-chip Communications inZynq-7000 All Programmable Systems-on-Chip
Abstract: This letter analyses and compares on-chip interfaces for hardware/software communications in the Zynq-7000 all programmable systems-on-chip. Many experiments were carried out to evaluate the exchange of
data between the processing system andthe programmable logic through general-purpose and high-performance
ports; the experiments were conducted for both standalone and Linux applications. The results enable the most effective interfaces for specific types of data to be identified and the effectiveness of Zynq-based hardware
accelerators to be assessed.
2015
10
EMB_2015_10
Topic: Task-Aware Interrupt Controller: Priority SpaceUnification in Real-Time Systems
Abstract; In the development of real-time systems, predictability is often hindered by technological factors
which breakthe timing abstractions offered by real time operating systems (RTOSs); namely, the priority space separation between threadsand interrupts induces the rate-monotonic
2015
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
problem. Softwareapproaches have tackled this issue, attempting to unify the priority space with varying degrees of success. We present a hardwareapproach to the problem: unifying the priority
space at the interrupt handling subsystem, predictability is greatly enhancedwith minimum software
modifications. Our solution providesthe interrupt controller with awareness of the currently running task’s priority making the solution independent of the used operating system. We show how our approach is
minimally intrusiveat hardware architecture level and provides benefits beyond the
capabilities of previous approaches. Our technique shows a 0.05%run-time overhead if no interrupts occur, and run-time reductionproportional to interrupt rate for rates higher than 5 per s, for a
interrupt workload around 0.07 ms.
11
EMB_2015_11
Topic: Scheduling Dynamic Hard Real-Time Task Sets onFully and Partially Reconfigurable Platforms
Abstract: Reconfigurable systems are increasingly beingemployed in a large class of today’s heterogeneous
real-timeembedded systems which often demand satisfaction of stringenttimeliness constraints. However, executing a set of hard real-timeapplications on reconfigurable systems such that all timing
constraints are satisfied while also allowing efficient resourceutilization requires effective scheduling, mapping and admissioncontrol strategies. This letter presents methodologies for scheduling periodic hard real-time
dynamic task sets on fully andpartially reconfigurable field-programmable gate arrays (FPGAs).
The floor of the FPGA is assumed to be statically equipartitionedinto a set of homogeneous tiles (each of which act as individualprocessing elements or PEs) such that any arbitrary task of thegiven task set may be feasibly
mapped into the area of a given tile.Experimental results reveal that the proposed algorithms are able
to achieve high resource utilization with low task rejection ratesover a variety of simulation scenarios.
2015
12
EMB_2015_12 Topic: Exploiting Partially-Forgetful Memories forApproximate Computing
Abstract: While the memory subsystem is already a majorcontributor to energy consumption of embedded systems, theguard-banding required for masking the effects of ever increasing
manufacturing variations in memories imposes even more energyoverhead. In this letter, we explore how
Partially-ForgetfulMemories can be used by exploiting the intrinsic tolerance ofa vast class of applications to some level of error for relaxingthis guard-banding in memories. We discuss the challenges to
be addressed and introduce Relaxed Cache as an exemplarto address these challenges for partially-forgetful
SRAMcaches. Preliminary results show how adapting guard-bands toapplication characteristics can help the system save significantamount of cache leakage energy (up to 74%) while still generating
acceptable quality results.
2015
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
13
EMB_2015_13
Topic: Hibernus: Sustaining Computation During Intermittent Supply for Energy-Harvesting System
Abstract: A key challenge to the future of energy-harvesting systems is the discontinuous power supply that is
often generated.We propose a new approach, Hibernus, which enables computation to be sustained during intermittent supply. The approach hasa low energy and time overhead which is achieved by reactively
hibernating: saving system state only once, when power is aboutto be lost, and then sleeping until the supply
recovers. We validate the approach experimentally on a processor with FRAM nonvolatile memory, allowing it
to reactively hibernate using only energy stored in its decoupling capacitance. When compared to a recently
proposed technique, the approach reduces processor timeand energy overheads by 76%–100% and 49%–79%
respectively.
2015
14
EMB_2015_14 Topic: A Security Layer for Smartphone-to-VehicleCommunication Over Bluetooth
Abstract: Modern vehicles are increasingly being interconnected with computer systems, which collect
information bothfrom vehicular sources and Internet services. Unfortunately,this creates a nonnegligible attack
surface, which extends whenvehicles are partly operated via smartphones. In this letter, a hierarchically distributed control system architecture which integrates a smartphone with classical
embeddedsystems is presented,and an ad-hoc, end-to-end security layer is designed to demonstrate how a
smartphone can interact securely with a modernvehicle without requiring modifications to the existing in-vehicle network. Experimental results demonstrate the effectiveness ofthe approach.
2015
15
EMB_2015_15
Topic: WSN-Based Smart Sensors and Actuator for PowerManagement in Intelligent Buildings
Abstract: The design and development of a smart monitoringand controlling system for household
electrical appliances in realtime has been reported in this paper. The system principally monitors
electrical parameters of household appliances such as voltage and current and subsequently
calculates the power consumed.The novelty of this system is the implementation of the controlling
mechanism of appliances in different ways. The developedsystem is a low-cost and flexible in
operation and thus can saveelectricity expense of the consumers. The prototype has been extensively
tested in real-life situations and experimental results are veryencouraging.
2015
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
EMBEDDED 2014 PAPERS
SN PROJECT
CODE
PROJECT TOPIC YEAR
1
NEMB1425
Topic: GSM CONTROLLED ROBOTICS
Abstract: In traditional methodology to find the motion of human we have some devices like video camera,
radar, ultrasonic sensor etc. In case of video camera another human have to continuously monitor the video. If we use radar orultrasonic sensor, we need a transmitter and a receiver. So these are high in cost and most of the
jamming techniques are there to cheat (i.e. stealth bomber planes). But there is anotherinteresting sensing device
used to find the motion of human (i.e.) PIR (PyroelectricInfra Red sensor). It absorbs the infrared radiation (wave length of 9.4 micro meters) from the human body and creates a corresponding signal. As it has protection
devices like lenses it is less suppose to be cheated. As this is sensitive only human body heat and frequency of
radiation, this sensor can be used to find human upto 3 meter to 90 meter distance (using perfect Fresnel lenses). So it helps to find human availability beyond the barriers like walls and fire etc. It can be used as earth quake
rescuer.
2014
2
NEMB1424
Topic: Passenger BUS Alert System for Easy Navigation of Blind
Abstract: Talking signs, guide cane, echolocations are all useful in navigating the visually challenged
people to reach their destination, but the main objective is not reached that it fails to join them with traffic. In this project we propose a bus system using wireless sensor networks (WSNs).The blind people
in the bus station is provided with a ZigBee unit which is recognized by the ZigBee in the bus and the indication is made in the bus that the blind people is present in the station. So the bus stops at the
particular station. The desired bus that the blind want to take is notified to him with the help of speech
recognition system HM2007. The blind gives the input about the place he has to reach using microphones and the voice recognition system recognizes it .The input is then analyzed by the
microcontroller which generates the bus numbers corresponding to the location provided by the blind.
These bus numbers are converted into audio output using the voice synthesizer APR 9600. The ZigBee transceiver in the bus sends the bus number to the transceiver with the blind and the bus number is
announced to the blind through the headphones. The blind takes the right bus parked in front of him
and when the destination is reached it is announced by means of the GPS-634R which is connected with the controller and voice synthesizer which produces the audio output. Thisproject is also aimed at
helping the elder people for independent navigation.
2014
Topic: Autonomous Greenhouse Mobile Robot DrivingStrategies From System Integration
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
3
NEMB1423
Perspective:Review and Application
Abstract: Agricultural operations are constantly becomingtechnology-driven mainly due to labor shortages,
increase in labor cost, and trends in new and advanced technology applications.In this paper, we have presented a system-of-systems approach todesign and development of a mobile robotic platform for agricultural applications.
Similar to other field robots, the mobile platform for agricultural applications requires a different set of
predefined attributes for its operation. We have designed, fabricated, anddemonstrated the mobile platform for pesticide spraying application. The design and development includes synergistic integrationof mechanical, sensor
and actuator, navigational and control, andelectronic and software interfacings. The autonomous
navigationaspect of the development was achieved via three stages: learningstage, implementation stage (training stage), and testing stage. Inthe learning stage, we defined the path patterns and studied andrecorded the behavior
of the vehicle in real-world environment. Inthe training stage, various steering algorithms for four-wheel driving
system were developed and inherent errors were compensatedusing advanced tools and methods. In the testing stage, we put therobotic platform on an arbitrary path pattern and demonstratedits success in autonomous
navigation. The medium-sized mobilerobot can be commercialized for greenhouse-based agriculturaloperations.
2014
4
NEMB1422
Topic: Autonomous Appliance Scheduling for HouseholdEnergy Management
Abstract: The advancement of renewable energy technologieshas seen the emergence of customer owned grid
tied wind andsolar microgrids. These microgrids offer an opportunity to energyusers to lower their energy costs as well as enabling the powersuppliers to regulate the utility grid. However, the integration ofthe renewable
energy based sources into the smart grid increasesthe complexity of the main grid. The success of this scheme willbe heavily reliant on accurate real-time information exchange between the microgrid, the main
grid,andtheconsumers.Thecommunication between these agents will be critical in implementationof intelligent
decisions by the smart grid. The microgrids will berequired to relay energy forecastsinformation to the utility grid.Similarly, customers will be expected to submit energy demandschedules, to actively monitor energy price
signals, to participatein energy bids, and to respond to energy management signals inreal time. This kind of grid-
userinteraction will be overwhelmingand could result in consumer apathy. There is therefore a needto develop smart systems that will autonomously execute all thesetasks without the prompting of the customers. This paper
presentsone such approach. In this study, we proposed a demand side energy management for a grid connected
household with a locallygenerated photovoltaic energy. To ensure efficient household energy management, smart scheduling of electrical appliances hasalso been presented.
2014
5
NEMB1421
Topic: A Compact and Compliant ExternalPipe-Crawling Robot
Abstract: The focus of this paper is on the practical aspects ofdesign, prototyping, and testing of a compact,
compliant externalpipe-crawling robot that can inspect a closely spaced bundle ofpipes in hazardous environments and areas that are inaccessible tohumans. The robot consists of two radially deployable
compliantring actuators that are attached to each other along the longitudinal axis of the pipe by a bidirectional
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
linear actuator. The robotimitates the motion of an inchworm. The novel aspect of the compliant ring actuator is a spring-steel compliant mechanism thatconverts circumferential motion to radial motion of its multiplegripping
pads. Circumferential motion to ring actuators is provided by two shape memory alloy (SMA) wires that are
guided byinsulating rollers. The design of the compliant mechanism is derived from a radially deployable mechanism. A unique feature ofthe design is that the compliant mechanism provides the necessarykinematic
function within the limited annular space around thepipe and serves as the bias spring for the SMA wires. The
robothas a control circuit that sequentially activates the SMA wires andthe linear actuator; it also controls the crawling speed. The robothas been fabricated, tested, and automated. Its crawling speed isabout 45 mm/min, and
the weight is about 150 g. It fits within anannular space of a radial span of 15 mm to crawl on a pipe of60-mm
outer diameter.
6
NEMB1420
Topic: O-Track: Towards Order Tracking for Tagsin Mobile RFID Systems
Abstract: In many logistics applications of RFID technology, luggage attached with tags are placed on moving
conveyor beltsfor processing. It is important to figure out the order of goods on the belts so that further actions
like sorting can be accuratelytaken on proper goods. Due to arbitrary goods placement or the irregularity of wireless signal propagation, neither of the order oftag identification nor the received signal strength provides
sufficient evidence on their relative positions on the belts. In this study,we observe, from experiments, a critical
region of reading rate when a tag gets close enough to a reader. This phenomenon, aswell as other signal attributes, yields the stable indication of tag order. We establish a probabilistic model for recognizing
thetransient critical region and propose the OTrack protocol to continuously monitor the order of tags. To validate the protocol, we
evaluate the accuracy and effectiveness through a one-month experiment conducted through a working conveyor
at BeijingCapital International Airport.
2014
7
NEMB1419
Topic: Portable Roadside Sensors for Vehicle Counting,Classification, and Speed Measurement
Abstract: This paper focuses on the development of a portableroadside magnetic sensor system for vehicle
counting, classification, and speed measurement. The sensor system consists ofwireless anisotropic magnetic
devices that do not require to beembedded in the roadway—the devices are placed next to theroadway and measure traffic in the immediately adjacent lane. Analgorithm based on a magnetic field model is proposed to
makethe system robust to the errors created by larger vehicles drivingin the nonadjacent lane. These false calls
cause an 8% errorif uncorrected. The use of the proposed algorithm reduces thiserror to only 1%. Speed measurement is based on the calculationof the cross correlation between longitudinally spaced sensors.Fast
computation of the cross correlation is enabled by usingfrequency-domain signal processing techniques. An
algorithm forautomatically correcting for any small misalignment of the sensorsis utilized. A high-accuracy differential Global Positioning Systemis used as a reference to measure vehicle speeds to evaluate theaccuracy of
the speed measurement from the new sensor system.The results show that the maximum error of the speed
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
estimatesis less than 2.5% over the entire range of 5–27 m/s (11–60 mi/h).Vehicle classification is done based on the magnetic length and anestimate of the average vertical magnetic height of the vehicle.Vehicle length is
estimated from the product of occupancy andestimated speed. The average vertical magnetic height is
estimatedusing two magnetic sensors that are vertically spaced by 0.25 m.Finally, it is shown that the sensor system can be used to reliablycount the number of right turns at an intersection, with an accuracy of 95%. The
developed sensor system is compact, portable,wireless, and inexpensive. Data are presented from a large
numberof vehicles on a regular busy urban road in the Twin Cities, MN,USA.
8
NEMB1418
Topic: Receiver Autonomous Integrity Monitoring of GNSSSignals for Electronic Toll Collection
Abstract: Various road user charging mechanisms are usedto control traffic and its resulting pollution, as well as revenuesources for reinvestment in the road infrastructure. Among them,electronic toll collection (ETC) systems
based on user positionsestimated with Global Navigation Satellite Systems (GNSS) areparticularly attractive due
to their flexibility and reduced roadsideinfrastructure in comparison to other systems such as tollbooths.Because GNSS positioning may be perturbed by different errors and failures, ETC systems, as liability critical
applications,should monitor the integrity of GNSS signals in order to limitthe use of faulty positions and the
consequent charging errors.The integrity-monitoring systems have been originally designedfor civil aviation; hence, they need to be adapted to the ETCrequirements. This paper studies the use of receiver
autonomousintegrity monitoring (RAIM), which are algorithms run within theGNSS receiver and, therefore, are easier to tune to ETC needsthan other systems based on external information. The weightedleast squares residual
RAIM used in civil aviation is analyzed,and an algorithm modification for ETC is proposed.
Simulationsdemonstrate that the proposed RAIM algorithm has a superiorlevel of availability over civil-aviation-based RAIM procedures,particularly in urban environments.
2014
9
NEMB1417
Topic: A Decentralized Cooperative Control Scheme withObstacle Avoidance for a Team of Mobile
Robots
Abstract: The problem of formation control of a team ofmobile robots based on the virtual and behavioral
structuresis considered in this paper. In the virtual structure, each mobilerobot is modeled by an electric charge. The mobile robots movetoward a circle and due to repulsive forces between the identicalcharges, regular polygon
formations of the mobile robots willbe realized. For swarm formation, a virtual mobile robot islocated at the
center of the circle, and other mobile robotsfollow it. In the introduced approach, each mobile robot finds itsposition in the formation, autonomously, and the formation canchange automatically in the case of change in
the number of themobile robots. This paper also proposes a technique for avoidingobstacles based on the
behavioral structure. In this technique,when a mobile robot gets close to an obstacle, while movingtoward its target, a rotational potential field is applied to leadthe mobile robot to avoid the obstacle, without locating in
localminima positions.
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
10
NEMB1416
Topic: Circuit Design and Power Consumption Analysis ofWireless Gas Sensor Nodes: One-Sensor
VersusTwo-Sensor Approach
Abstract: Wireless sensor networks (WSNs) have recentlybeen applied in industrial monitoring applications includinghazardous gases detection. As a major power consumer ofa node, gas sensors may significantly
constrain its lifetime.Hence, the sensing circuit must be carefully designed to optimize
performance and retain accuracy. In this paper, we propose forthe first time the principle of gas concentration
measurementbased on a single sensor in a voltage divider circuit, instead ofthe well-known Wheatstone bridge
sensing circuit, which employstwo sensors. We discuss the design of a real WSN node for gassensing and
evaluate it with respect to an identical platform thatuses the Wheatstone bridge. The proposed approach ensuressignificant energy savings and helps to avoid zero offset issue.Besides, we employ a more efficient and
secure sensor heatingprofile; it does not damage the sensor and does not make gassensing dependent on
environmental conditions. Experimentalresults show a 30% reduction in power with respect to thestate-of-the-art.
2014
11
NEMB1415
Topic: RFID in undergroundMining Serviceapplications
Abstract: The mining industryemploys more than three million people and exports more than US$26 billion
worth of minerals and related materials each year.RFID offers numerous advantages for mining and related
industries, where hostile environments make it desirableto track personnel closely for safety reasons (for more information on RFID, see the sidebar). RFID can also help manage and control a fleet of mine vehicles, which is
especially beneficial given the increaseduse of remotely directed units.Close control of hazardous materials, such
as explosivesand detonators, is also critical in mining operations, presenting new opportunities for RFID.
2014
12
NEMB1414
Topic: Modeling and Detecting AggressivenessFrom Driving Signals
Abstract: The development of advanced driver assistance systems (ADASs) will be a crucial element in the
construction offuture intelligent transportation systems with the objective ofreducing the number of traffic
accidents and their subsequentfatalities. Specifically, driving behaviors could be monitored onlineto determine
the crash risk and provide warning information tothe driver via their ADAS. In this paper, we focus onaggressivenessas one of the potential causes of traffic accidents. We demonstratethat aggressiveness can be
detected by monitoring external drivingsignals such as lateral and longitudinal accelerations and speed.We model
aggressiveness as a linear filter operating on thesesignals, thus scaling their probability distribution functions andmodifying their mean value, standard deviation, and dynamicrange. Next, we proceed to validate this model
via an experiment,conducted under real driving conditions, involving ten differentdrivers, traveling a route with
five different types of road sections,subject to both smooth andaggressivebehaviors. The obtainedresults confirm the validity of the model of aggressiveness. Inaddition, they show the generality of this model and its
applicability to specific driving signals (speed, longitudinal, and lateralaccelerations), every single driver, and
every road type. Finally, webuild a classifier capable of detecting aggressive behavior from thedriving signal. This classifier achieves a success rate up to 92%.
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
13
NEMB1413
Topic: Performance of Drivable Path Detection System of Autonomous Robots in Rain and snow Scenario
Abstract: Drivable path detection is an important factor to consider for a successful development of autonomous
robot which is characterized as an intelligent vehicle. Researchers usingdifferent vision-based techniques have achieved remarkable result toward drivable path detection. Regardless of this achievement, environmental noise
such as rain and/or snow can cause misdetection of drivable path which can lead to autonomous robot accident.
In this paper, after investigating the effects of rain and/or snow, we introduced into the drivable path detection system a filtering algorithm that addresses the detection and removal of rain and/or snow for the optimization of
the system. Experiments were carried out to show the effectiveness of the filter in the system. The results show
that filtering algorithm assists the autonomous driving system in navigating perfectly during rain and/or snow scenario with minimal accident.
2014
14
NEMB1412
Topic: Motion Planning of Multi-docking System forIntelligent Mobile Robots
Abstract :The article develops a multi-docking system with a mobile robot and three docking stations. The
docking structure is designed with one active degree offreedom and two passivedegrees of freedom. The
controller of the power detection devices is HOLTEK microchip, and acquires measurement values of the real-time current and voltage of the mobile robot and the docking stations. The power detection devices contain three
power detection systems and one power detection module. Thepower detection system is embedded in the
docking station and monitors the real-time information for the charging process. The controller of the mobile robot receives these measurement values from the power detection module via RS232 interface. The article
focuses on the searching process using multiple sensors and a laser range finder for the mobile robot. The laser range finder searches the landmark of each docking station, and guides the mobile robot moving to the assigned
docking station. In the experimental results, the power of the mobile robot is under the threshold value. The
mobile robot selects the free and nearestdocking station according to the received information from each docking station via wireless RF interfaces. The laser range finder guides the mobile robot moving approach to the
assigned docking station. The power of the mobile robot is enough to be detected by the power detectionmodule.
The docking station turns off the charging current, and trigs the mobile robot leaving the docking station via wireless RF interface.
2014
15
NEMB1411
Topic: A GSM-based Versatile Unmanned Ground Vehicle
Abstract: Operations like radioactive waste handling, bombdisposal, surveillance, search and rescue are today performed mostly by humans at great risk to their own safety and wellbeing. In order to
minimize direct human intervention in such operations, the design of a remotely operated versatile
Unmanned Ground Vehicle (UGV) mounted with a robotic manipulator is presented in this paper. The robustness, range and security of the communication link between the remote basestation and the robot,
obstacle avoidance and the real time control of the robot are some of the major issues encountered
while deploying such robots in the above scenarios. In this paper,the design of a versatile UGV which leverages the already existing GSM mobile telephony network to establish a longrange, secure, fast and
reliable connection with the remote base station is presented. The UGV is also mounted with a robotic
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
manipulator with four degrees of freedom with a gripper type end-effector, which can be used for grabbing objects and thus help in search and rescue type operations. The robot is equipped with IR sensors and
camera for obstacle detection and avoidance. The camera is also used to send the visual information back to
the base station in real-time, allowing accurate control of and monitoring over long distances.
16
NEMB1410
Topic: Application of Fire Monitoring and Personnel Evacuation in Subway Station Based on
Wireless Sensor Network
Abstract: It is a common topic to apply the fire monitoring and personnel evacuation in fire safety field
of inside building. But there are few applying researches on fire safety field of underground building,
especially in subway station fire. This paper made a trial application ofWSN (Wireless Sensor Network) technology into fire monitoring and personnel evacuation during subway station fire, and built a
synthetic system of fire monitoring and personnel evacuation based on some advanced algorithms. And
the system has been proved to work effectivelyin monitoring fire and directing the distressed people and rescuers to evacuate in the subway station fire.
2014
17
NEMB1409
Topic: Design of an Intelligent Security Robot for Collision Free Navigation Applications
Abstract: Robotics industry has replaced human efforts gradually in performing rather difficult tasks. A
very pertinent aspect of an intelligent security robot is to reach the goal safely byavoiding unknown obstacles
in an unknown environment. In this paper we have developed an embedded C program code to design an intelligent robot which can overcome the obstacles coming in its way. We have made use of three infrared
sensors to detect the obstacles via the IR communication technique. The IR transmitter sends out infrared
radiation in a direction which consequently bounces back on coming across the surface of an object and thereafter is picked up by the IR receiver. Authors have applied amulti sensor integration technique to
sense the obstacles using an LED based IR transmitter and receiver module integrated with the 8051 micro
controller which permits collision free navigation of robots.
2014
18
NEMB1408
Topic: PROTOTYPE OF A FINGERPRINT BASED LICENSING SYSTEM
FOR DRIVING
Abstract: To prevent non-licensees from driving and therefore causing accidents, a new system is proposed. An
important and very reliable human identification method is fingerprint identification. Fingerprint identification is one of the most popular and reliable personal biometric identification methods. The proposed system consists of
a smart card capable of storing the fingerprint of particular person. While issuing the license, the specific
person’s fingerprint is to be stored in the card. Vehicles such as cars, bikes etc should have a card reader capable of reading the particular license. Thesame automobile should have the facility of fingerprint reader device. A
person, who wishes to drive the vehicle, should insert the card (license) in the vehicle and then swipe his/her
finger. If the finger print stored in the card and fingerprint swiped in the device matches, he/she can proceed for ignition, otherwise ignition will not work. Moreover, the seat belt detector verifies and then prompts the user to
wear the seat belt before driving.This increases the security of vehicles and also ensures safe driving by
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
preventing accidents.
19
NEMB1407
Topic: Authenticating Vehicles and Drivers in Motion Based on Computer Vision and RFID Tags
Abstract: A system consisting of a vehicle interior-mounted device and a supporting infrastructure is designed to allow authorized drivers and authorized vehicles to access restricted areas of the airports, as well as
government, office and private parking facilities. The device authenticates tothe infrastructure using its own
digital certificate, while the driver authenticates through the digital certificate stored onhis or her smart card
inserted into the device. The system can be configured to work with and without additionalbiometric verification
of the driver.
2014
20
NEMB1406
Topic: EMBEDDED BASED GREEN HOUSE MONITORING SYSTEM
USING PIC MICROCONTROLLER
Abstract: The embedded system innovation has the close and indivisible relationship with the
environment science aesthetics. This paper deals with a simple, easy to install,microcontroller-based
circuit to monitor and record the value of temperature, humidity, soil moisture and sunlightof the natural environment that are continuously modified and controlled in order optimize them to achieve maximum plant
growth and yield. The controller communicates with the various sensor modules in real-time in order to control
the light, aeration and drainage process efficiently inside agreenhouse by actuating a cooler, fogger, dripper and lights respectively according to the necessary condition of the crops. The environmental is the important
resource that guides the environmental development of embedded system, and an important guarantee that
makes the embedded system develop and innovate along healthy, scientific environmental road. This makes the proposed system to be an economical, portable and a low maintenance solution for greenhouse
application, especially in rural areas and for small scale agriculturists.
2014
21
NEMB1405
Topic: A Novel Design For Vehicle License PlateDetection and Recognition
Abstract: License plate recognition (LPR) plays a major role in this busy world, as the number of vehicles
increases day by day, theft of vehicles, breaking traffic rules, entering restricted area are also increases linearly,
so to block this act license plate recognition system is designed. License Plate Recognition systems basically consist of 3 main processing steps such as: Detection of number plate, Segmentation of plate characters
and Recognition of each character. Among this, character segmentation is a most challenging task, as the
accuracy of the character recognition relieson the accuracy of the character segmentation. Problems of different lighting condition, adhesion, fracture, rivet, rotationdegrades the accuracy of the character
segmentation. So in order to come these problems and uplift the accuracy of character segmentation various
algorithms are developed for this work. This thesis presents a robust method of license plate location, segmentation and reorganization of the characters present in the located plate. The images of various
vehicles have been acquired and converted in to gray-scale images. Then noise present in the plates are
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
removed and the segmentation of gray scale image generated by finding edges for smoothing image is used to reduce the number of connected component and then bw label is used tocalculate the connected component.
Finally, single character in the license plate is detected. The aim is to show that the proposed method
achieved high accuracy by optimizing various parameters with higher recognition rate than the traditional methods.
22
NEMB1404
Topic: Vision-Based Path Planning with Obstacle Avoidance for Mobile Robots using Linear Matrix
Inequalities
Abstract: In this paper, a vision-based obstacle avoiding path generation problem is considered for autonomous
mobile robots under a top-view workspace. The collision-free path planning problem is converted to a convex optimization problem that can be solved numerically using linear matrix inequalities (LMI). A new optimal
(shortest) path cost formulation is given for LMI optimization using a novel Line of Sight Meshing (LSM)
method. As compared to the traditional meshing algorithms such asVoronoi and Delaunay, the LSM generates fewer mesh cells which results in reduced computation time. A virtual path diagram (VPD), consisting of all
collision-free piecewise straightline paths, is then found for robot navigation. The LMI optimization method is
then used to find the optimal (shortest)collision-free path from the VPD set. In addition to distance, other constraints, such as terrain condition and curvature of the path can be incorporated in the cost function for
constrained optimal solution. Finally, a rapid prototyping (RP) environment has been developed, which is used
for hardware implementation of the algorithm. The generated paths are then converted to motion commands, which are sent wirelessly from a base-station to mobile robots for motion control.
2014
23
NEMB1403
Topic:Design of Tracked Robot with Remote Control for Surveillance
Abstract: For specific purpose, tracked robot that can be controlled remotely and able to acquire images from
environment is very important, for example in rescuing disastervictims. We propose architecture for Raspberry pi
and AVRbased mobile robot that can be controlled by low cost remote controller Integrated Circuits(IC) and able
to avoid obstacles using ultrasonic distance sensor. This prototype also can be used for education and research in
the university. We evaluate theperformance of the robot in terms of the distance and the capability to deliver video streaming from the output raspberry pi and 2.4 GHz Video transmitter.
2014
24
NEMB1402
Topic: DEVELOPMENT OF A ROBOTIC ARM FOR DANGEROUS OBJECT
DISPOSAL
Abstract: The Boko Haram insurgency in Nigeria has become menace and threat to the security of lives and property most especially in the Northern part of the country. The use of Bombs and dangerous unsuspected
objects is the weapon employed to carry out this deadly act. The number of liveslost as well as personnel who
sustain injuries while discharging their duties is now on the increase as a result oflack of initial assessment of a dreadful scene or an object suspected to be harmful. Though preventive and counter attacking measures, such as
use of protective vest have been employed to reduce the risk experienced; these however do not guarantee safety
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
which can run into huge cost to restorein terms of infrastructures and properties. Hence this paper proposes the development of a robotic arm for dangerousobject disposal. A three-degree of freedom robotic arm was
developed using a microcontroller programmed with (MPLAB) integrated development environment software,
interfaced to a camera that transmits the video by way of monitoring the scene on a television set. The system is activated by a remote control thereby providing a line of defense to human lives and preventing loss of proven
and tested personnel.
25
NEMB1401
Topic: The House Intelligent Switch Control Network Basedon CAN Bus
Abstract: In this paper a building lighting intelligent switchcontrol network is presented, which is based on
CAN bus.According to the safety ,stability and real time, the digital signalsare used for the control unit, and the
CAN bus is used as acommunication of a distributed control network. A 16-bit MCUmsp430f169 is used as the control unit, and the communicationbetween the nodes is based on CAN bus. This paper mainlyintroduces the
design of the hardware and the software in detail.The experimental result shows this network system with
highsafety, stability and strong anti-jamming capability withpractical significance and market value.
2014
EMBEDDED PROJECTS
SN PROJECT
CODE
PROJECT TOPIC YEAR
1
MEMB1470
Topic: RF BASED DUAL-MODE CAR
Abstract: Here is a dual-mode robot that can be operated manually using an RFbased remote controlled and can also move automatically avoiding all the obstacles. The robot has some inbuilt intelligence to avoided
obstacles by changing its path.
2014
2
MEMB1469
Topic:WIRELESS STEERING WITH INTELLIGENT VEHICLE
Abstract: It wait for your hand movement, if you hand moves to down direction car moves to forward , if
someone come towards the car, the car automatically stop, at this movement we run our car left, right, and back not to forward because if strike to the front object. if obstacle is disappear then, our car run forward, if
someone come in left hand side of the car, our car automatically run slightly to right hand side, to avoid the
obstacle, and run forward, or some obstacle come right hand side of the car, our car automatically run
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
slightly left hand side, to avoid the obstacle, and run forward, if you move up your hand it starts run back, if you hand is left hand side your car run left hand side, if your hand is right hand side then car run to
right hand side. If your hand is on middle you car is stop.
3
MEMB1468
Topic: RADIO FREQUENCY BASED 31 CHANNELS ELECTRICAL CONTROL PANEL
Abstract: This project is consist with RF transmitter and RF-RECIVER, so we operate it from 100/200 meters
and work even through walls, you can control large AC and DC loads and many appliances through
relay, including lights, fans, AC system, home appliances, garage doors, door locks, sprinklers, and
motorized projection screen
2014
4
MEMB1467
Topic: CARD LOCK OF APPLIANCE
Abstract: The circuit presented here can be used as a lock for important electronic and its mechanism, depending upon the positions of the holes punched on the card, a particular appliance is switched on. The card is
inserted just like a CD is pushed inside the disk drive. It is rectangular in shape with holes
Punched on it. The electronic lock is connected to an access control system, which ensures that only the selected appliance is switched on and prevents false operation of the system.
2014
5
MEMB1466
Topic: INTELLIGENT TRAIN TO REDUCE THE ACCIDENT ON FOGY SESSION
Abstract: As we read in the news paper that the one train get hit from the another train due to fogy session,
this type of accident is held on winter session, when Driver not seen the RED signal. This problem is reduced by this project, this project automatically off the train engine on the red light, and
on the train Engine of green light. Driver run the train only on the green light, it never run the engine when red
signal is on.
2014
6
MEMB1465
Topic:INTERACTIVE VOICE RESPONSE SYSTEMFOR COLLEGE AUTOMATION (IVRS)
Abstract: Now-a-days every institution needs automation. As a part of college automation, we have decided to do a project Voice Interactive System for College Automation. Our project allows the user to know the
student's attendance and marks quickly through the telephone line without the intention of the college
authority. In the hardware side embedded system has been used. A 20 pin microcontroller 89C2051 is used because of its compatibility with our hardware. This microcontroller controls the whole hardware. Telephone
line is used for communication purpose. Visual Basic has been used for software programming. Presentation
in the class and outcome of the university are made reachable to the parents by our project. It will be very obliging to the parents to be acquainted with their son's/daughter's recital in the college.
2014
Topic: HEART RATE MONITOR
Abstract: Heart rate can be measured either by the ECG waveform or by the blood flowinto the finger (pulse
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
7 MEMB1464 method). The pulse method is simple and convenient. When blood flows during the systolic stroke of the heart into the body parts, the finger gets its blood via the radial artery on the arm. The blood flow into
the finger can be sensed photo electrically. To count the heart beats, here we use a small light source on one side
of the finger (thumb) and observe the change in light intensity on the other side. The blood flow causes variation in light intensity reaching the light dependent resistor (LDR), which results in change in signal strength
due to change in the resistance of the LDR.’
2014
8
MEMB1463
Topic: HOME AUTOMATATION OVER INTERNET
Abstract: We can ON/OFF the eight devices from any part of the world using internet, we check the
Status of the each device, can our tube light, bulb, switch is ON or OFF, We also send the three message to the system, all three message will display on lcd using micro controller.
2014
9
MEMB1462
Topic: ON FOGGY (COLD) DAYS IT WILL AUTOMATICALLY OFF THE TRAIN ENGINE ON RED
LIGHT & UNMANNEG RAIL GATE CONTROL SYSTEM
1. Features as follows. 2. Close the gate from safe distance when train comes near unmanned rail gate (crossing).
3. Gate will automatically close when train is passed.
4. This project is work from both sides. 5. Message and direction will display on LCD.
6. Buzzer on when train come and off when it passed.
7. We also implement in foggy (cold) days it will automatically off the train engine on red light.
2014
10
MEMB1461
Topic: INTELLIGENT TRAFFIC LIGHT SYSTEM
Abstract: Traffic light intervals are fixed independent of traffic movement. So sometimes large red light delay
cause traffic congestion. Here is a microcontroller based intelligent traffic light system that reduces the
possibility of traffic jams caused by traffic light delays to an extent. Microcontroller counts the number of vehicles passing the road. Based on the vehicle count, the system has
three traffic profiles-low, medium and high. The system contains different traffic light intervals (red, yellow,
and green light delays in seconds) for different traffic profiles. After calculating the traffic profiles , Depending on the number of vehicles passing trough the IR system in a
predefined controlling interval (e.g. one minute). It further controls the timing of traffic Lights. After the
controlling interval lapses, the vehicle count is reinitialized to zero to calculate the traffic profile again in the next controlling interval. The lcd Display current profile delay (RED, YELLOW, GREEN),
current profile (LOW, MID, HIGH), running time of the system
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
(HH:MM:SS), and also display how Many vehicles were passed (VEH:05 ) and so on.
11
MEMB1460
Topic: CELLPHONE BASED DEVICE CONTROL WITH VOICE ACKNOWLEDGEMENT (IVRS)
Abstract: Here is a circuit that lets you operate your home appliances like lights and water pump from your office or any other remote place. S0 if you forgot to switch off the lights or other appliances while going
out, it helps you to turn off the appliance with your cell phone. Your cell phone works as the remote
control for your home appliances. You can control the desired appliance by pressing the corresponding
key. The system also gives you voice acknowledgement of the appliance status.
2014
12
MEMB1459
Topic: PROTECT SCHOOL CHILDREN FROM LPG LEAKAGE IN SCHOOL VAN/TAXI
Abstract: It will save school children from car fire due to LPG leakage in schoo l car/van/ taxi etc.
when this system detect LPG leakage in car it will automatically off the engine, after repairing the LPG leakage it will allow to start the engine.
2014
13
MEMB1458
Topic: ALCHOLE TESTER
Abstract: This project is used for deny entry from alcoholic people in ladies parties, temples, hospitals,
highways, school, college etc.
2014
14
MEMB1457
Topic: AUTOMATION SYSTEM FOR ANY INDUSTIES FOR EXAMPLE COLLEGE/HOTELS
Abstract: This project takes 8 different inputs for 8 different users / rooms. And glow 8 different LEDs
as per room number, for example room no. 1 wants service from peon. Corresponding led1 is glow, after providing the service peon off the LED by pressing room number key, it also on the alarm when any user press
the button.
2014
15
MEMB1456
Topic: UNMANED RAIL GATE SYSTEM
Features are as follows. 1. Close the gate from safe distance when train comes near unmanned rail gate (crossing).
2. Gate will automatically close when train is passed.
3. This project is work from both sides. 4. Message and direction will display on LCD.
5. Buzzer on when train come and off when it passed.
6. We also implement so many things as per your budget.
2014
Topic: PROGRAMMABLE INDUSTRIAL ON-OFF TIMER WITH RF REMOTE
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
16 MEMB1455 Abstract: In most of the modern manufacturing and processing industries, there is complete industrial automation through sophisticatehardware and software like programmable logic controller (PLC), distributed
control system (DCS), and supervisory control and data acquisition (SCADA).
Microcontroller-based embedded systems play major role in industrial automation. One such widely used system is the programmable timer. The major applications of programmable timer are as follows: 1. initiating
the process after desired time. 2. Switching on/ off the process after
predetermined time 3. Providing delay in between processes 4. Applying input to on/off type open-loop control system depending upon the requirement of process, one can set the time of programmable timer. As
the time period expires, the timer will either trigger 01'shut the process. Earlier
there were mechanical timers that used gear assembly (same as wall clock) and mechanical contacts. But the problem with these was that due to mechanical parts and movements, they were not durable. Electronic
timers have become very popular as these have more functionalities and long
operating life. A simple electronic timer can be to enhance theprogrammable timer for generating precise timing and additional features, micro controllers (embedded controllers) are used with peripheral devices. Some
of the features of programmable industrial on/ off timer presented
here include: 1. Time set from 1 to 60 seconds (canbe extended) 2.. 'On' time and' off' time can beprogrammed (from 1 to 60 seconds 3. Repeat (continuous) and single operation 4. Fully remote-
controlled within 100-metre range 5. User-friendly front-panel controls and display panel with LCD 6.
Emergency stop buttons (on control panel as well as on remote) 7. Provision of potential-free relay contacts for connecting any 230VAC at lOA or 28V DC at lOA device/ application
2014
17
MEMB1454
Topic: SEND SECURED MESSAGE TO RECEIVER USING WIRELESS MEDIA
Abstract: This project is used to communicate / Transmits a alpha numeric message from one place to another
place through wireless media, first we encrypted the message and then transmit it, from wireless tx. At receiving side we decrypted it and matching the code also if, both are match message will display on
LCD.
2014
18
MEMB1453
Topic: DIGITAL IC TESTER USING PC AND CONTROLLER
Abstract: This project is used to check the Basic logic gates (AND, OR, NOT, NAND, NOR, EX-OR).
You can check the following IC's 7400, 7402, 7404, 7408, 7432, 7486 Visual Basic Program is used to show the results on the PC. The Microcontroller AT89S52 receives the IC number from the PC and checks the Gates
IC with the Truth table and sent back the result to the PC.
2014
19
MEMB1452
Topic: HOME AUTOMATION/WIRE LESS ELECTRIACL CONTROL PANEL/INFRA RED
REMOTE CONTROL
Abstract: This Project INFRARED REMOTE SWITCH USING MICROCONTROLLER is used to switch
on/off the Home Appliances by using a standard Remote control. The system is used to switch on/off unto eight
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
electrical devices. All the above processes are controlled by the 8 bit Microcontroller AT89C2051. The Microcontroller receives the Infrared Signal from the receiver and it decodes and switch on/off the appropriate
Device. The Range of the system is unto 10 meters. The system works on
Phillips RC5 format. The project can switch on/off electrical devices of maximum load current of 5Amperes. High power loads can also be connected by changing the Relay. The Microcontroller is used to
receive the Infrared signal from the Transmitter, the received signal is processed by the Microcontroller
and according to the signal the corresponding device is switched ON/OFF.
20
MEMB1451
Topic: ELECTRONIC VOTING MACHINE
Abstract: Now-a-days Electronic voting machines are being used effectively. The confidence of the voter in its flawless working is gradually building up and these machines are thus becoming quite popular throughout the
country. Features of the electronic voting machine include avoidance of
invalid votes and reduction of counting time and the consequent expenditure incurred on manpower deployment. By using the Microcontroller the voting machine can be built up easily and it will make simple to
operate.
21
MEMB1450
Topic: ULTRA SONIC DISTANCE METER
Abstract: There are several ways to measure distance without contact. One way is to use ultrasonic waves at
40 kHz for distance measurement.
2014
22
MEMB1449
Topic: PASSWORD/ACCESS CONTROL SYSTEM FOR HOME/OFFICE/ATM(AVR
MICROCONTROLLER BASED)
Abstract: Security is a prime concern in our day-to-day life. And access control system forms a vital link in a
security chain. The microcontroller - based digital lock presented here is an access control system that
allows only authorized persons to access a restricted area. When someone tries to enter the restricted area by entering invalid passwords continuously, the system locks itself and can be unlocked only by the master user.
This means this system have two passwords, the system comprises a small electronic unit with a numeric
keypad, which is fixed outside the entry door to control a relay/solenoid-operated lock. When an authorized person enters a predetermined number (password) via the keypad, the relay energies for a limited time to
unlock the solenoid operated lock, so doorcan be pushed/ pulled open. At the end of the preset delay, the re lay
de -energies and the door get locked again. A prompt message is displayed on the LCD module. And we modified this project as per
student requirement.
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
23
MEMB1448
Topic: WIRELESS KEY WITH PASSWORD FOR CAR/HOME/OFFICE. (AVR MICRO
CONTROLLER BASED)
Abstract: This is an wireless system, consist with TX and RX, the tx is always with you as key ring,, so no one can access this device, but if someone pick your tx, the rx take password, if password is entered three time
wrong, the system is locked, it unlocked by system administrator One sysadm
provide right password the system can un locked otherwise system not work. Range between Tx and Rx
approx 3-10 mtrs.(use full in cars/ house/ etc).
2014
24
MEMB1447
Topic: 8 TO 30 DEVICES CONTROLLER USING MICRO CONTOLLER
Abstract: The project will run on both Windows-98 and Windows-XP, This project not used parallel port,
it used rs232 (serial port) for interfacing, in parallel we cannot transmitted data more the then 1-5 meters, but in serial communication we can transmit data more than 50 -100 meters, and parallel port based project off
automatically when we off our pc but, this project not have this problem, in parallel port based we can control
max 8 to 12 device. But in this we can control 30 or more. This project also give you status that which device is in or off, we can modified this project as per requirement of students.
2014
25
MEMB1446
Topic: RSEB POWER CUT SYSTEM USING COMPUTER
Abstract: RSEB cuts lights according timetable time table, say 10:00 am automatically cut light of Area 1,
at 1:00pm automatically light on a t area 1, at 1:00 pm automatically light cut of area 2, at 3:00 pm automatically light on at area 2 and so no for many area. This project work on hh:mm:ss format so we can cut for
miniutesas well as for seconds, and we can cut/restore the power for more than one area. We can modified
this project as per requirement of students.
2014
26
MEMB1445
Topic: TEMPRATURE DEPENDENT FAN
Abstract: This is new generation fan its speed increase and decrease depending upon temperature. It have
both automatically/Remotely Controlled, It also controlled by wire less system also.
2014
27
MEMB1444
Topic: WATER LEVEL TANK CONTROLLER(UNDER AND OVER TANK FLOW CONTORL)
Abstract: When water in the tank is below sensor A, the motor will switch on to fill water in the tank. The LCD
module will show 'motor on.' The controller is programmer for a 10- minute time interval to check the dry-run
condition of the motor. If water reaches sensor B within 10 minutes, the micro controller comes out of the dry-run condition and allows the motor to keep pushing water in the tank. The
motor will remain 'on' until water reaches sensor C. Then it will stop automatically and the microcontroller
will go into the standby mode. The LCD module will II show 'tank full' followed by 'standby mode' after a few seconds. The 'standby mode' message is displayed until water and if the dry-
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
run condition still persists, the display will show' drysump3' and the micro controller will not start the motor automatically. Now you have to check the line for water and manually
reset the microcontroller to start operation. In the whole procedure, themicro controller checks for high and
low voltages. For example, when the voltage is high, it will scan for about two seconds to check whether it is a fluctuation. If the voltage remains high after two seconds, the microcontroller will halt running of the
motor. Now it will wait for the voltage to settle down. After the voltage becomes normal, it will still check for
90 seconds whether the voltage is normal or not. After normal condition, it will go in the standby mode and start the aforementioned procedure.
28
MEMB1443
Topic: SMART PATHFINDER ROBOT
Abstract: Moves with its two wheels and makes use of infrared emitting diodes as its eyes to avoid obstacles along its path. Smart pathfinder robot automatically makes a left turn the moment it detects an object in
its path. It continues to move forward again when no obstacle is in the way.
2014
29
MEMB1442
Topic: RF AND INFRA RED FREQUENCY BASEDMOBILE LAND ROVER
Abstract: We present here is an elementary robotic land rover that can be controlled remotely using primarily the RF mode. The RF remote control has the advantage of adequate range (up to 200 metres with
proper antennae) besides being omni directional. On the other hand, an IR remote would function over a
limited range of about 5 metres and the remote transmitter has to be oriented towards the receiver module
quite precisely. Costinvolved in using RF modules is much higher than of IR components and as such, we have
included the replacement alternative of RF modules with
their IR counterparts for using the IR remote control. The proposed land rover can move in forward and reverse directions. You would also be able to steer it towards left and right directions. FORWARD,
REVERSE, LEFT, RIGHT, STOP CONTROLLED BY RF/INFRA RED.
2014
30
MEMB1441
Topic: WIRELESS DETECTIVE ROBOT
Abstract: With the help of RF remote control we run the robot in FORWARD, REVERSE, LEFT, RIGHT, STOP CONTROLLED. We also attach RF camera with Robot, to see what is going on the
remote location.
2014
Topic: MOBILE PHONE BASED MOBILE ROBOTIC OR CAR
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
31 MEMB1440 Abstract: We can control our robot with mobile phone, it can move left, right, forward, backward, stop. 2014
32
MEMB1439
Topic: SMARD CARD BASED AUTOMATIC TOOL TAX SYSTEM
Abstract: This project is designed to make unattended automatic toll tax stations at check barriers check
posts automatic toll tax, it work like pre-pad toll tax system, if open the gate when authorized person with money charged in it card.
2014
33
MEMB1438
Topic: PC BASE WIRELESS APPLICANCE CONTROL
Abstract: The parallel port of the PC is a powerful platform for implementing projects dealing with the
control of real-world peripherals. It can be used to control home and other electronic appliances. The computer program through the interface circuit controls the relays, which, in turn, switch the appliances' on' or 'off.' Here
we describe how to wirelessly control electronic appliances from a remote place by using the RF module. For
this PC-based wireless appliances control system, you need to design and develop .the required hardware and software. The parallel port of the PC is used to control the appliances at the transmitter side. The RF
interface is used instead of the IR to overcome all the drawbacks of the IR interface. The PC signals are
transmitted from the RF transmitter and received by the RF receiver.
2014
34
MEMB1437
Topic: MICRO CONTROLLER BASED CODE LOCK SYSTEM
Abstract: If we provide right password our device will on other wise device not on, and it will give only three
Chances, if any one try more than three times, buzzer automatically on, and full system goes hang. What is
going on all display on 16x2 lcd.
2014
35
MEMB1436
Topic: KOUN BANAGA KORORPATI USING MICROCONTROLLER
Abstract: Useful for quiz games, dumb charades, etc, this fastest -finger- first circuit displays the player number along with a beep sound when a specific player presses the button before others. It is designed for seven
players and can be constructed easily using minimal hardware and software. When the microcontroller
receives an input from any of the seven tactile switches (Sl through S7), it disables the inputs from rest of the switches assigned to other players. A master reset control (switch SO) has to be pressed to enable all
the inputs for the next round of the quiz.
2014
36
MEMB1435
Topic: COUNTER DOWN TIMER FOR INDUSTRIES TO ON/OFF THE MACHINE AS DESIRED
TIME
Abstract: This project is used for on/off the 220v ac device as per the time, we provide the input as
per time, After the time complete the system automatically on/off the device, we can start, stop, time +
-, reset the system by pressing the switch.
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
37
MEMB1434
Topic: RF BASED WIRELESS DEVICE CONTROL SYSTEM
Abstract: The Wireless Device Control project can control numerous devices from one point. Four to eight devices can be easily controlled with the help of the project. The Blue tooth or Infra red based transmitter and
Blue tooth or Infra red based receiver are used to control the performance of the project and restricts the use of
wires. The software can only be controlled by a single person, which makes it a secure feature of the
device. Nobody except the concerned person can operate the project.
2014
38
MEMB1433
Topic: MICRO CONTROLLER BASED (GREEN FARM HOUSE)
Abstract: This is automatically system for advance farming. It has following features. 1. It automatically ON
the lights/heater to maintain heat lever for plants. 2. It automatically ON and OFF the water pumps as per soil water level. 3. It displays current temperature also.
2014
39
MEMB1432
Topic: MICRO CONTROLLER BASED WATCH MAN TIMER
Abstract: When we go away from our house this project will work as a watch man. It will on the light as per
time specified, Basically It is based on RTC (real time clock). It will display time as well as store 8
different time according your 8 time specified it will auto matically on the device and off the device automatically.
2014
40
MEMB1431
Topic: MICRO CONTROLLER BASED AUTOMATICROOM LIGHT CONTROLLER
Abstract: Every one knows ―save electricity save money‖, this project will help for saving money by
stopping the misuse of electricity, When no one is not in room it will automatically off the light / fan etc. If
some one come in the room it will make on the light if night / or lowlight, and make a fan on if cold, so on student can change this project as he/she like.
2014
41
MEMB1430
Topic: MICRO CONTOLLER BASED MULTI CHANNEL CODE LOCK SYSTEM USING PIC
MICRO CONTROLLER
Abstract: This micro controller based project can be used for preventing unauthorized access to devices or solenoid-operated locks/electrical devices. This code lock can be used as a multi-user code lock, where the
users can access respective devices by entering the device number followed by the password. The password
can be changed by the user and no external supply is needed to retain the password. The password length for each device can be between 4 to 15 d igits, as desired by the user.
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
42
MEMB1429
Topic: MICRO CONTROLLER BASED SINGLE STEPPER MOTOR CONTROLLER
Abstract: This project is use to control the rotation of a DC stepper motor in clockwise and anti-clock
wise direction. It can be used in many applications including machine control and robotics for controlling the axial rotations in XY plane. A similar circuit can be added to control the
rotation of the motor in either XZ or YZ plane.
This embedded system off the motor with off button.
Run motor clockwise or anticlockwise.
Speed control (+ -)
2014
43
MEMB1428
Topic: MICRO CONTROLLER BASED ONE DC MOTOR CONTROLLER
Abstract: Dc motor speed controllers are very useful for controlling the motion of robotic and industrial automation systems. The controller presented here uses the pulse-width modulation (PWM) technique. The
PWM wave for speed control is generated using Atmel AT89C52 microcontroller. To control the speed of
the DC motor, you need a variable -voltage DC power source. When the DC motor is switched on, it takes certain time to reach the full speed. As soon as the power supply is switched on, the DC motor
starts gaining speed and if you switch off the
power supply before it reaches the maximum rated speed, it starts to slow down. In case switching on and switching off are done in quick succession, the motor rotates at a slower speed between zero and full rated speed.
This is what a PWM technique based controller does: it switches the motor' on' and 'off' with a pulse train. To
control the motor speed, it varies (modulates) the width of the pulses-hence the pulse width modulation. When the motor is, on‟ for a short period and 'off' for a long one, it will rotate slowly. When the motor is 'on'
for most of the time and' off' only for a short while, it will rotate at higher speed, say, nearly at full (maximum)
rated speed.
2014
44
MEMB1427
Topic: FLOOD CONTOL SYSTEM
Abstract: This system take a input from dam and display in the LCD, if water is greater than danger level it will
make a buzzer on and open the gate so water follow to safe area.
2014
45
MEMB1426
Topic: WIRELESS MICROCONTROLLER BASEDAUTOMATIC FLUSH SYSTEM
Abstract: In manual flush system the user press a button, which opens a flush valve allowing mains-pressure
water to flow into the bowl, or sometimes the user press directly a flush lever (a handle connected to a flush
meter). The value contains a pneumatic mechanism that closes it after a reset time. Today, manual flush system has been replaced with a sensor operated system that automatically flushes
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
the fixture when the user departs. The microcontroller based automatic flush system is infrared sensor to detect a user approaching the fixture, then it wait until the user departs. It also
flushes before the person departs if the person is person for more than the preset time (5 minutes).
46
MEMB1425
Topic: MOVING MESSAGE DISPLAY USINGALPHA NUMERIC DISPLAY
Abstract: LED-based moving- message displays are becoming popular for transmitting information to
large groups of people quickly. These can be used indoors or outdoors. We can find such displays in areas
like railway platforms, banks, public offices, hotels, training institutes, nightclubs and shops. Compared to
LEDs, liquid-crystal displays (LCDs) are easy to interface with a microcontroller for displaying
information as these have many built-in functions. But these can't be observed from a distance and large size LCDs are very costly. LED-based displays can be of two types: dot-matrix and segmental. If you
implement a moving- message display with multiplexed dot- matrix LEDs, it will be very costly for displaying
16 characters or more at a time.
2014
47
MEMB1424
Topic: MICROCONTROLLER BASED METRO TRAIN
Abstract: The project – Metro train has been developed keeping in mind the Delhi Metro Rail Corporation
scenario. The project targets to provide guidance to the passengers of the metro train. The LCD display
informs about the upcoming station and guides them to get down at their destination.
2014
48
MEMB1423
Topic: DIGITAL CLOCK WITH HOURLY MUSIC WITH RELAY CONTOL
Abstract: This project is based on AVR micro controller on which it will on buzzer for one second after
each hour. It also on the alarm as per time specified and off after one second.
2014
49
MEMB1422
Topic: AUTOMATIC LIFT SYSTEM FOR BUILDING/COMPLEX/CIMEMA HALLS
Abstract: We can use this project for lifting heavy material/ persons from one floor to another floor. It makes
for 3 floors, as we press button for our required floor; it automatically goes to required floor.
2014
50
MEMB1421
Topic: VISITOR VIGILANCE SYSTEM
Abstract: This project only open the gate when some one come without weapon, If it finds a person with
weapon, it produce a sound as well as not open the gate, the system will open the gate and close for the
visitors, automatically.
2014
51
MEMB1420
Topic: MUSICAL TOUCH BELL
Abstract: This project is give sound when some one touches it.
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
52
MEMB1419
Topic: THREE IN ONE ALARM
Abstract: This project will give alarm when it detects fire ―or‖ water full on the tank, and produce sound when
some One come on the room.
2014
53
MEMB1418
Topic: AUTOMATIC STREET LIGHT ON/OFF ON VEHICLE MOVEMENT IN HIGHWAY
Abstract: In highway road light is glow even, no motor or car on the highway. This will misuse of road light and
electricity, it increase global warming, for overcome this problem we introduce this circuit. Project makes
―power on‖ the some light when any vehicle is come and ―power off‖ the some light when it passes through the sensor. And off the hole light in morning, and on the some light on night, so no
darkness in the highway.
2014
54
MEMB1417
Topic: DIGITAL SECURITY SYSTEM
Abstract: This circuit can help you from the intruders and strangers. Very thin copper wire loop has to be
wired around your house and if any of the copper wire loops is broken, the display the particular number of
the loop with buzzer sound. If more than one loop are broken it will display the sum of their loops. (Wireless version also available).
2014
55
MEMB1416
Topic: IR REMORE CONTROL RECEIVER
Abstract: It is an infra red receiver, it can on/off any device like radio, cooler, T.V, etc with the help of any Remote control of your home appliances.
2014
56
MEMB1415
Topic: LONG-RANGE FM TRANSMITTER
Abstract: The high-power output obtained using a power amplifier stage allows a range of about 2 km
for this FM transmitter. Reasonable good signal quality and strength are possible with little adjustments.
2014
57
MEMB1414
Topic: WATER LEVEL INDICATOR WITH THREE LEDS
Abstract: It will display on led. How many water present in tank. Like low, mid and high. It also alarm you if water tank is full.
2014
Topic: UNMANNED RAIL CROSSING SYSTEM
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
58
MEMB1413
Abstract: This project open the unmanned railway crossing gate from the safe distance before train to near
the gate, after train pass it will close the gate.
2014
59
MEMB1412
Topic: DIGITAL IC BASED CAR PROTECTION UNIT
Abstract: For car protection, custom- made units are available but they are costly. Here's a circuit to
protect car stereo, etc from pilferage that costs less and requires no adjustments in the car but a good car
cover. Place the circuit at your bedside and bring the two wires from the unit to the car (parked outside
your home) and connect one wire -end to the cover and the other to the ground, with both wire-ends shorted by
some weight such as a brick. So outwardly the mechanism is not visible. If some one tries to remove the cover, the alarm of the circuit starts sounding to alert you. The alarm can be switched off by resetting it using
switch S1.
2014
60
MEMB1411
Topic: AUTOMATIC GARDNER SYSTEM/SOILMOISTURE TESTER/AUTOMATIC PLANTIGING
SYSTEM
Abstract: It will start motor automatically when no water on the soil, and make a off when no need of
more water on the soil, it also display the water level in the plant.
2014
61
MEMB1410
Topic: ANTI-THEFT ALARM FOR VEHICLES
Abstract: Security system for vehicles which generates a loud and continuous alarm in case of any unauthorized person getting access of your vehicle. As soon as, auto-lifter tries to start the vehicle alarm gets activated and
buzzer gets on.
2014
62
MEMB1409
Topic: BANK TOKEN/DOCTOR TOKEN NUMBER
Abstract: Token Display System are ideal for Serving Counters in Offices, Banks, Airports, Doctors- Clinics,
Restaurants and other such places where people have to wait in line for their turn. These systems allow customers to wait without having to stand in lines. It is very uses full item for service industries.
2014
63
MEMB1408
Topic: DOOR BELL WITH SECURITY FEATURE
Abstract: Doorbell system work such that when someone presses your calling bell switch during the night, not
only the bell rings but the bulb connected to it also glow. In order to turn the bulb off, just press the reset pushbutton switch provided in the circuit.
2014
Topic: INFRARED CAR PARKING GUARD
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
64 MEMB1407 Abstract: This car parking guard circuit is basically an infrared active proximity detector. It will warn you when you will come very near to back side wall or other thing.
2014
65
MEMB1406
Topic: AUTOMATIC WASH BASIN TAPCONTROLLER SYSTEM
Abstract: Make your washbasin tap work automatically when you put your hands just below the water
tap outlet. This infrared based system detects any interruption of the IR rays by your hands or utensil
and water automatically starts flowing out of the tap.Electronic watchdog Here‟s an electronic watchdog for your house. That sound to in form you that somebody is at the gate. The circuit comprises a
transmitter unit and a receiver unit, which are mounted face to face on the opposite pillars of the gate such that
the IR beams gets interrupted when someone is standing at the gate or passing through it.
2014
66
MEMB1405
Topic: AUTOMATIC NIGHT LAMP WITH MORNING ALARM
Abstract: This circuit serves dual purpose, depending upon intensity of light rays detected. One part of
the circuit automatically detects darkness to switch „ON‟ a white bright LED which acts as night lamp. It‟s
another part senses daylight to switch on a melodious music in the morning. No external DC power supply is required, as the circuit operates on direct AC power supply line. But, provision for battery backup is provided
to power the circuit in case of mains failure.
2014
67
MEMB1404
Topic: LUGGAGE SECURITY SYSTEM
Abstract: The circuit sounds an alarm when somebody tries to cut the luggage chain. Different sound effects like
police siren, fire alarm, ambulance siren etc are possible after doing simple connections.
2014
68
MEMB1403
Topic: MIDNIGHT SECURITY LIGHT
Abstract: Most thefts happen after midnight hours when people enter the second phase of sleep called
'paradoxical' sleep. Here is an energy-saving circuit that causes the thieves to abort the theft attempt by lighting
up the possible sites of intrusion (such as kitchen or backyard of your house) at around1:00 am. It automatically resets in the morning.
2014
69
MEMB1402
Topic: TIMER FOR STUDENTS
Abstract: This timer gives alarm after a preset time period and a few beeps at half the selected time. The timer
can be programmed for other time periods as well.
2014
BULK EMBEDDED IEEE TITLES 2015-16
PONDICHERRY BRANCH Technos Inc.,II nd Floor, Natesan Tower, 100 FEET ROAD, PUDUCHERRY, 605 005 CT: +91 9566492473, +91 9585338678. E-MAIL: [email protected] , www.technosinc.blogspot.com , www.technosinc.page.tl
VILLUPURAM BRANCH
Technos Inc.,Pondy Main Road, Koliyanur, Villupuram.605103 CT: +919942340236, +919444340236. E-MAIL:[email protected] www.technosinc.blogspot.com , www.technosinc.page.tl
Project Cost Starting Range Rs 1,500 for Clients with Full Documentation with Complete 24*7 Online Support
70
MEMB1401
Topic: FIRE ALARM
Abstract: This fire detector circuit generates a loud and continuous alarm in case of fire. Here, a simple diode
is used as fire sensor, the reverse resistance of which decreases with increasing temperature. The circuit triggers the alarm when temperature reaches above 70ºC level. This level can be easily adjusted to suit the needs. (IC
BASED).
2014