BV

Se

rie

SVA

Ne

PU

MP

S

1010

Quality Products for Mechanical& Fluid Power

Versatility, power, compactness and low running costs are the main characteristics of B&C vanepumps. All the components subject to wear are contained in a cartridge unit that can be easily removedfor inspection and/or replacement without disconnecting the pump from the circuit, drastically reducingexpensive machine down time.The cartridge contains a rotor, vanes and inserts, a cam ring and two covers.During operation the rotor is driven by a splined shaftcoupled to the drive unit. As the rotation speed increases,centrifugal forces, in combination with the pressuregenerated behind the vanes, push the vanes outwards,where they follow the profile of the cam of the ring with asufficient contact pressure to ensure adequate hydraulicsealing. The two opposed pumping chambers formed bythe elliptical profile of the cam cancel out radial loads onthe shaft bearings, thereby giving them extremely longlifetimes.The versatility of the BV series pumps enables them tomeet the requirements of the most varied industrialapplications. In fact, as well as their proven high reliabilityand excellent volumetric efficiency in all working conditions,they operate with particularly low noise levels. This is madepossible by the special profile of the cam ring and the useof a 12 vane rotor that reduces the amplitude of the supplypressure pulses, thereby reducing induced vibrations (seedrawing).The BV series is available in four versions of single pump (from 8 to 230 l/min at 1200 rpm) and sixversions of double pump (from 55 to 370 l/min at 1200 rpm), with maximum powers of over 300 HP.The BV series pumps are extremely compact and are supplied with ISO norm mechanical couplingsand SAE norm hydraulic fittings. This makes them very easy to install and guarantees theirinterchangeability with other similar pumps.

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS “BV” SERIES

1

BV

2

contents

Single pumps BV01.....................................

Single pumps BV02.....................................

Single pumps BV04.....................................

Single pumps BV05.....................................

Double pumps BV21.....................................

Double pumps BV41.....................................

Double pumps BV42.....................................

Double pumps BV51.....................................

Double pumps BV52.....................................

Double pumps BV54.....................................

Id. codes of cartridge kit components............

Operating instructions...................................

BV

pag. 3

pag. 11

pag. 18

pag. 25

pag. 32

pag. 42

pag. 52

pag. 61

pag. 71

pag. 80

pag. 89

pag. 91

3

Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the type of cartridge usedand the speed of rotation. The pump isavailable in six versions with capacitiesfrom 8 to 55 l/min (from 2 to 14 gpm) at1200 rpm and 7 bar.

General description

BV01single pump

Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.

Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).

Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).

Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)

Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water

based fluids +15°C to +50°C.

Drive: direct and coaxial by means of a flexible coupling.

Technical characteristcs

Cartridgemodel

Geometricdisplacement

Ratedcapacity

Ratedcapacity

Maximumpressure

Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil

V01-02

V01-05

V01-08

V01-09

V01-11

V01-12

V01-14

cm3/g

7,2

18,0

27,4

30,1

36,4

39,5

45,9

(in3/r)

(0,44)

(1.10)

(1.67)

(1.83)

(2.22)

(2.41)

(2.79)

l/min

8,3

20,8

31,8

35,1

42,4

46,9

54,9

(gpm)

(2)

(5)

(8)

(9)

(11)

(12)

(14)

l/min

10,4

26,1

39,4

44,1

52,6

58,7

69,6

(gpm)

(2.8)

(6.9)

(10.4)

(11.7)

(13.9)

(15.5)

(18.4)

bar

210

210

210

210

210

160

140

min

600

600

600

600

600

600

600

max

1800

1800

1800

1800

1800

1800

1800

(psi)

(3050)

(3050)

(3050)

(3050)

(3050)

(2300)

(2030)

Sound level at 138 bar (2000 psi)

velocità

58

60

62

64

66

68

70

dB

(A)

1200 rpm 1500 rpm 1800 rpm

If the intake pressure is not zero bar, use the graph below to find the percentage correction factor toapply to the maximum speed

max speed / intake pipe pressure

% c

orr

ecti

on

fac

tor

for

the

max

sp

eed

106%

104%

102%

100%

98%

96%

94%

92%

-2,9 -1,45 0

PSI1,45 2,9 4,35

-0,2 -0,1 0 0,1 0,2 0,3 0,4

5,8

Intake pipe pressure (BAR)

max pressure / hydraulic fluid

Antiwear industrialhydraulic oil

Waterglycol

Water-in-oilemulsion

Main operating data

250

200

150

100

50

0

BA

R

3625

2900

2175

PS

I

1450

725

0

1214

1214

2, 5, 8,9, 11

2, 5, 8,9, 11 12 14

2, 5, 8, 9, 11

4

single pump BV01

max pres. Peak pres. (0,5 sec.max)

2000

1600

1200

800600400

0

RP

M

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

Water-in-oilemulsion

1800

1400

200

1000

max speed / hydraulic fluid (with 0 bar in the intake pipe)

5

single pump BV01

Cartridge V01-02flow / pressure

PSI

l/min G

PM

16

6

2

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

14

2,8

12

8

BAR

20

4,16

KW

0

1

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

8,16

0

HP

0 50 100 150 200 250

power / pressure

3

5

7

8

5,44

2,72

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

100

NM

50

3040

BAR

5,2

3,12

1,04

10,9

4

10

18

2

4

6

20

Cartridge V01-05

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

80

40200

NM

BAR50

60

power / pressure

KW

0

2

4

6

8

10

12

14

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

21,6

16,2

10,8

5,4

0

HP

0 50 100 150 200 250

16

18

flow / pressurePSI

l/min

GP

M

45

35

15

10

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

10,4

7,8

5,2

0

0 50 100 150 200 250

2,6

40

30

25

20

5

1200 rpm

1500 rpm

1800 rpm

2500 rpm

6

BV01single pump

Cartridge V01-08flow / pressure

PSI

l/min G

PM

60

20

10

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50

7,8

40

30

13

BAR

70

15,6

5,2

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

27,2

0

HP

0 50 100 150 200 250

power / pressure

10

15

20

25

20,4

13,6

6,8

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

50

0

NM

50

100

150

BAR

18,2

10,4

2,6

34

Cartridge V01-09

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

50

0

NM

50

100

150

BAR

flow / pressurePSI

l/min G

PM

60

20

10

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

0

0 50 100 150 200 250

50

7,8

40

30

13

80

15,6

5,2

20,8

10,4

2,6

18,270

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

27,2

0

HP

0 50 100 150 200 250

power / pressure

10

15

20

30

20,4

13,6

6,8

40,8

25 34

7

BV01single pump

Cartridge V01-11

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

150

50

0

NM

BAR50

100

power / pressure

KW

0

5

10

15

20

25

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

47,6

34

20,4

6,8

0

HP

0 50 100 150 200 250

30

35

flow / pressurePSI

l/min

GP

M

90

70

30

20

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

21,2

15,9

10,6

0

0 50 100 150 200 250

5,3

80

60

50

40

10

1200 rpm

1500 rpm

1800 rpm

2500 rpm

40,8

27,2

13,6

Cartridge V01-12flow / pressure

PSI

l/min G

PM

90

30

10

0

0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200

70

10,4

60

40

20,8

BAR

100

KW

0

5

BAR

PSI0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

34

0

HP

0 50 100 150 200

power / pressure

15

20

25

30

27,2

20,4

6,8

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

50

0

NM

50

100

150

BAR

26

15,6

5,2

40,8

80

50

20

10 13,6

BV01single pump

8

Installation dimensions mm (inches)

Approx. weight: 12 Kg. (26 lbs.)

Cartridge V01-14

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

200

100

0

NM

BAR50

150

power / pressure

KW

0

5

10

15

20

25

BAR

PSI

0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

40,8

34

20,4

6,8

0

HP

0 50 100 150 200

30

flow / pressurePSI

l/min

GP

M

120

80

20

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

31,8

21,2

10,6

0

0 50 100 150 200

5,3

100

60

401200 rpm

1500 rpm

1800 rpm

2500 rpm

27,2

13,6

26,5

15,9

50

PSI

0 1450 2175 2900725

BV01

9

Model code breakdown

BV 01 G * * * * * (L) * (A)

Cartridge type02 05 08 09 11 12 14

Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)

Pump type

Outlet port positions(outlet viewed from cover end)

A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet

Mounting(omit if not required)

Shaft options mm (inches)

PORT ORIENTATIONS

Pump series Design Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)

Shaft end options01 = Straight with key (standard)11 = Splined90 = Splined SAE B

Spline data(shaft 11 and shaft 90)

Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 13Pitch 16/32Major dia. 22.00 - 21.90 (0.866 - 0.862)Pitch dia. 20.638 (0.8125)Minor dia. 18.63 - 18.35 (0.733 - 0.722)Wildhaber 11.67 - 11.70 (0.459 - 0.461)

Shaft01

Shaft11

Shaft90

single pump

BV01

10

single pumpId

. cod

es o

f pum

p co

mpo

nent

s

Par

t N

o. M

8010

010

Bo

dy

Par

t N

o.

M80

2042

0To

rque

to 7

0 N

m (

625

lb. i

n.)

Scr

ew

Mo

del

01 11 90

Sh

aft

kit

Par

t N

o.

M80

1060

1M

8010

611

M80

1069

0

Mo

del

01 11 90

Sh

aft

Key

Par

t N

o.

K01

0100

0K

0111

000

K01

9000

0

Par

t N

o.

M80

1010

0- -

Par

t N

o.

M80

2006

0M

8020

065

M80

2006

1M

8020

066Sh

aft

seal Ty

pe

prim

ary

in N

BR

prim

ary

in F

PM

seco

ndar

y in

NB

Rse

cond

ary

in F

PM

Par

t N

o.

M80

1003

0

Bea

rin

g

Par

t N

o.

M80

2012

0

Co

ver

Par

t N

o.

M80

1004

0

See

ger

Pu

mp

sea

l kit

Typ

eN

BR

NB

RF

PM

(V

iton®

)F

PM

(V

iton®

)

Par

t N

o.

M80

1050

0M

8010

501

M80

1050

3M

8010

504

Par

tsse

als

+ 1

sha

ft se

alse

als

+ 2

sha

ft se

als

seal

s +

1 s

haft

seal

seal

s +

2 s

haft

seal

s

Par

t N

o.

M80

1005

0

See

ger

Car

trid

ge

Ser

ies

V01

V01

Mo

del

02 05 08 09 11 12 14 02 05 08 09 11 12 14

Par

t N

o.

V01

0200

2V

0105

015

V01

0803

5V

0109

055

V01

1107

5V

0112

095

V01

1411

5V

0102

007

V01

0502

5V

0108

045

V01

0906

5V

0111

085

V01

1210

5V

0114

125

Pu

mp

ro

tat.

right

han

d

left

hand

11

Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the type of cartridge usedand the speed of rotation. The pump isavailable in five versions with capacitiesfrom 47 to 79 l/min (from 12 to 21 gpm)at 1200 rpm and 7 bar.

General description

BV02

Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.

Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).

Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).

Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)

Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water

based fluids +15°C to +50°C.

Drive: direct and coaxial by means of a flexible coupling.

Technical characteristcs

Cartridgemodel

Geometricdisplacement

Ratedcapacity

Ratedcapacity

Maximumpressure

Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil

single pump

V02-12

V02-14

V02-17

V02-19

V02-21

cm3/g

40,1

45,4

55,2

60,0

67,5

(in3/r)

(2.45)

(2.77)

(3.37)

(3.66)

(4.12)

l/min

46,9

52,7

64,2

71,0

79,0

(gpm)

(12)

(14)

(17)

(19)

(21)

l/min

58,8

65,7

80,2

88,7

99,8

(gpm)

(15.5)

(17.4)

(21.2)

(23.4)

(26.4)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

BV02single pump

12

max pressure / hydraulic fluid

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

max pres. Peak pres. (0,5 sec.max)

Water-in-oilemulsion

If the intake pressure is not zero bar, use the graph below to find the percentage correction factor toapply to the maximum speed

max speed / intake pipe pressure

Main operating data

250

200

150

100

50

0

BA

R3625

2900

2175

PS

I

1450

725

0

2000

1600

1200

800600400

0

RP

M

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

Water-in-oilemulsion

1800

1400

200

1000

% c

orr

ecti

on

fac

tor

for

the

max

sp

eed

106%

104%

102%

100%

98%

96%

94%

92%

-2,9 -1,45 0

PSI1,45 2,9 4,35

-0,2 -0,1 0 0,1 0,2 0,3 0,4

5,8

max speed / hydraulic fluid (with 0 bar in the intake pipe)

Intake pipe pressure (BAR)

Sound level at 138 bar (2000 psi)

speed

58

60

62

64

66

68

70

dB

(A)

1200 rpm 1500 rpm 1800 rpm

13

BV02single pump

Cartridge V02-12

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure0 725 1450 2175 2900 3625

PSI

200

100500

NM

BAR50

150

power / pressure

KW

0

5

10

15

20

25

30

BAR

PSI0 725 1450 2175 2900 3625

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

54,4

40,8

27,2

13,6

0

HP

0 50 100 150 200 250

35

40

flow / pressurePSI

l/min

GP

M

100

80

40

30

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

26

20,8

15,6

0

0 50 100 150 200 250

5,2

90

70

60

50

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

10

10,4

2500 rpm

Cartridge V02-14flow / pressure

PSI

l/min G

PM

100

20

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

80

10,4

60

40

20,8

BAR

120

26

5,2

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

600 rpm

54,4

0

HP

0 50 100 150 200 250

power / pressure

10

15

40

50

40,8

27,2

13,6

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

100

0

NM

50

150200

BAR

31,2

15,6

68

45

30

25

35

20

50

1000 rpm

14

BV02single pump

Cartridge V02-17

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

250

150

500

NM

BAR50

200

power / pressure

KW

0

10

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

68

40,8

13,6

0

HP

0 50 100 150 200 250

50

60

flow / pressurePSI

l/min

GP

M

140

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

36,4

31,2

26

0

0 50 100 150 200 250

5,2

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

15,6

100

20,8

10,4

30

54,4

27,2

100

Cartridge V02-19flow / pressure

PSI

l/min G

PM

100

20

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

80

10,4

60

40

20,8

BAR

120

26

5,2

KW

0

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

54,4

0

HP

0 50 100 150 200 250

power / pressure

10

40

60

40,8

27,2

13,6

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

100

0

NM

50

200250

BAR

31,2

15,6

81,6

30

20

50

140

160

36,4

41,6

50 68

150

BV02single pump

15

Installation dimensions mm (inches)

Approx. weight: 15 Kg. (33 lbs.)

Cartridge V02-21

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

0

NM

BAR50

200

flow / pressurePSI

l/min

GP

M

140

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

42

31,5

21

0

0 50 100 150 200 250

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100

10,5

100

160

180

300

power / pressure

KW

0

10

20

40

BAR

PSI

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

68

40,8

13,6

0

HP

0 50 100 150 200 250

50

70

30

54,4

27,2

60

95,2

BV02

16

Model code breakdown

BV 02 G * * * * * (L) * (A)

Cartridge type12 14 17 19 21

Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)

Pump type

Outlet port positions(outlet viewed from cover end)

A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet

Mounting(omit if not required)

Shaft options mm (inches)

PORT ORIENTATIONS

Pump series Design Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)

Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE B

Spline data(shaft 11 and shaft 90)

Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 13Pitch 16/32Major dia. 22.00 - 21.90 (0.866 - 0.862)Pitch dia. 20.638 (0.8125)Minor dia. 18.63 - 18.35 (0.733 - 0.722)Wildhaber 11.67 - 11.70 (0.459 - 0.461)

Shaft01

Shaft11

Shaft90

Shaft86

single pump

BV02

17

single pumpId

. cod

es o

f pum

p co

mpo

nent

s

Par

t N

o. M

8020

010

Bo

dy

Par

t N

o.

M80

2003

0

Bea

rin

g

Par

t N

o.

M80

2005

0

See

ger

Par

t N

o.

M80

2004

0

See

ger

Par

t N

o.

M80

2002

0

Co

ver

Par

t N

o.

M80

2006

0M

8020

065

M80

2006

1M

8020

066S

haf

t se

al Typ

epr

imar

y in

NB

Rpr

imar

y in

FP

Mse

cond

ary

in N

BR

seco

ndar

y in

FP

M

Pu

mp

sea

l kit

Typ

eN

BR

NB

RF

PM

(V

iton®

)F

PM

(V

iton®

)

Par

t N

o.

M80

2050

0M

8020

501

M80

2050

3M

8020

504

Par

tsse

als

+ 1

sha

ft se

alse

als

+ 2

sha

ft se

als

seal

s +

1 s

haft

seal

seal

s +

2 s

haft

seal

s

Car

trid

ge

Ser

ies

V02

V02

Mo

del

12 14 17 19 21 12 14 17 19 21

Par

t N

o.

V02

1203

0V

0214

070

V02

1711

0V

0219

150

V02

2119

0V

0212

040

V02

1408

0V

0217

120

V02

1916

0V

0221

200

Pu

mp

ro

tat.

right

han

d

left

hand

Mo

del

01 11 86 90

Sh

aft

kit

Par

t N

o.

M80

2060

1M

8020

611

M80

2068

6M

8020

690

Mo

del

01 11 86 90

Sh

aft

Key

Par

t N

o.

K02

0100

0K

0211

000

K02

8600

0K

0290

000

Co

dic

e N°

M80

1010

0-

M80

2860

0-

Par

t N

o.

M80

2007

0To

rque

to 1

02 N

m (

910

lb. i

n.)

Scr

ew

18

Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the type of cartridge usedand the speed of rotation. The pump isavailable in five versions with capacitiesfrom 80 to 140 l/min (from 21 to 38 gpm)at 1200 rpm and 7 bar.

General description

BV04

Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.

Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).

Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).

Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)

Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water

based fluids +15°C to +50°C.

Drive: direct and coaxial by means of a flexible coupling.

Technical characteristcs

Cartridgemodel

Geometricdisplacement

Ratedcapacity

Ratedcapacity

Maximumpressure

Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil

single pump

V04-21

V04-25

V04-30

V04-35

V04-38

cm3/g

69,0

81,6

97,7

112,7

121,6

(in3/r)

(4.2)

(5)

(6)

(6.9)

(7.4)

l/min

79,5

94,0

113,8

131,6

139,9

(gpm)

(21)

(25)

(30)

(35)

(38)

l/min

101,4

120,1

141,2

167,2

177,3

(gpm)

(26.8)

(31.7)

(37.3)

(44.1)

(46.8)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

BV04single pump

19

max pressure / hydraulic fluid

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

max pres. peak pres. (0,5 sec.max)

Water-in-oilemulsion

max speed / hydraulic fluid (with 0 bar in the intake pipe)

If the intake pressure is not zero bar, use the graph below to find the percentage correction factor toapply to the maximum speed

max speed / intake pipe pressure

Main operating data

250

200

150

100

50

0

BA

R3625

2900

2175

PS

I

1450

725

0

2000

1600

1200

800600400

0

RP

M

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

Water-in-oilemulsion

1800

1400

200

1000

% c

orr

ecti

on

fac

tor

for

the

max

sp

eed

110%

104%

102%

100%

98%

96%

94%

92%

-2,9 -1,45 0

PSI1,45 2,9 4,35

-0,2 -0,1 0 0,1 0,2 0,3 0,4

5,8

108%

106%

Intake pipe pressure (BAR)

Sound level at 138 bar (2000 psi)

speed

60

62

64

66

68

70

dB

(A)

1200 rpm 1500 rpm 1800 rpm

20

BV04single pump

Cartridge V04-21

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

300

0

NM

BAR50

200

power / pressure

KW

0

10

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm1500 rpm

1200 rpm

1000 rpm

600 rpm

108,8

81,6

0

HP

0 50 100 150 200 250

50

80

flow / pressurePSI

l/min

GP

M

180

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

42

31,5

0

0 50 100 150 200 250

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100

21

10,5

30

54,4

27,2

100

140

160

70

60

Cartridge V04-25flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50 13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm1500 rpm1200 rpm1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

power / pressure

10

40

90

54,4

27,2

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

1000

NM

50

300400

BAR

39,6

30

20

200

250

52,8

66

50

108,8

200

60

80

70

21

BV04single pump

Cartridge V04-30

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

136

0

HP

0 50 100 150 200 250

120

flow / pressurePSI

l/min

GP

M

250

50

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

66

39,6

0

0 50 100 150 200 250

150

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100 26,4

13,2

81,6

27,2

200

200

60

52,8

80

100

108,8

54,4

Cartridge V04-35flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50

13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

power / pressure

40

120

54,4

27,2

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

0

NM

50

400

600

BAR

39,6

20

200

300

52,8

79,2

136

200

60

100

250 66

80 108,8

BV04single pump

22

Installation dimensions mm (inches)

Approx. weight: 23 Kg. (50 lbs.)

Cartridge V04-38

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

140

flow / pressurePSI

l/min

GP

M

50

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

79,2

52,8

26,4

0

0 50 100 150 200 250

200

1200 rpm

1500 rpm

1800 rpm

2400 rpm

100

13,2

54,4

27,2

300

60

190,4

600

150 39,6 80

200

250 66

100

120 163,2

136

108,8

BV04

23

Model code breakdown

BV 04 G * * * * * (L) * (A)

Cartridge type21 25 30 35 38

Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)

Pump type

Outlet port positions(outlet viewed from cover end)

A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet

Mounting(omit if not required)

Shaft options mm (inches)

PORT ORIENTATIONS

Pump series Design Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)

Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C

Spline data(shaft 11 and shaft 90)

Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)

Shaft01

Shaft11

Shaft90

Shaft86

single pump

BV04

24

single pumpId

. cod

es o

f pum

p co

mpo

nent

s

Par

t N

o.

M80

4014

0

Bo

dy

Par

t N

o.

M80

4016

0

Bea

rin

g

Par

t N

o.

M80

4018

0

See

ger

Par

t N

o.

M80

4017

0

See

ger

Par

t N

o.

M80

4015

0

Co

ver

Par

t N

o.

M80

4020

0To

rque

to 2

25 N

m (2

010

lb. i

n.)

Scr

ew

Par

t N

o.

M80

4019

0M

8040

195

M80

4019

1M

8040

196Sh

aft

seal Ty

pe

prim

ary

in N

BR

prim

ary

in F

PM

seco

ndar

y in

NB

Rse

cond

ary

in F

PM

Pu

mp

sea

l kit

Typ

eN

BR

NB

RF

PM

(V

iton®

)F

PM

(V

iton®

)

Par

t N

o.

M80

4050

0M

8040

501

M80

4050

3M

8040

504

Par

tsse

als

+ 1

sha

ft se

alse

als

+ 2

sha

ft se

als

seal

s +

1 s

haft

seal

seal

s +

2 s

haft

seal

s

Car

trid

ge

Ser

ies

V04

V04

Mo

del

21 25 30 35 38 21 25 30 35 38

Par

t N

o.

V04

2103

0V

0425

070

V04

3011

0V

0435

150

V04

3819

0V

0421

040

V04

2508

0V

0430

120

V04

3516

0V

0438

200

Pu

mp

ro

tat.

right

han

d

left

hand

Mo

del

01 11 86 90

Sh

aft

kit

Par

t N

o.

M80

4060

1M

8040

611

M80

4068

6M

8040

690

Mo

del

01 11 86 90

Sh

aft

Key

Par

t N

o.

K04

0100

0K

0411

000

K04

8600

0K

0490

000

Par

t N

o.

M80

4010

0-

M80

4860

0-

25

Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the type of cartridge usedand the speed of rotation. The pump isavailable in five versions with capacitiesfrom 164 to 230 l/min (from 42 to 60gpm) at 1200 rpm and 7 bar.

General description

BV05

Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.

Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).

Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).

Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)

Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water

based fluids +15°C to +50°C.

Drive: direct and coaxial by means of a flexible coupling.

Technical characteristcs

Cartridgemodel

Geometricdisplacement

Ratedcapacity

Ratedcapacity

Maximumpressure

Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil

single pump

V05-42

V05-47

V05-50

V05-57

V05-60

cm3/g

138,6

153,5

162,2

183,4

193,4

(in3/r)

(8.46)

(9.4)

(9.9)

(11.2)

(11.8)

l/min

164

180

189

217

230

(gpm)

(42)

(47)

(50)

(57)

(60)

l/min

203,4

222,7

234

267

285

(gpm)

(53.7)

(58.8)

(61.8)

(71.2)

(75.3)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

BV05single pump

26

max pressure / hydraulic fluid

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

max pres. peak pres. (0,5 sec.max)

Water-in-oilemulsion

max speed / hydraulic fluid (with 0 bar in the intake pipe)

If the intake pressure is not zero bar, use the graph below to find the percentage correction factor toapply to the maximum speed

max speed / intake pipe pressure

Main operating data

250

200

150

100

50

0

BA

R3625

2900

2175

PS

I

1450

725

0

2000

1600

1200

800600400

0

RP

M

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

Water-in-oilemulsion

1800

1400

200

1000

% c

orr

ecti

on

fac

tor

for

the

max

sp

eed

120%

115%

110%

105%

100%

95%

90%

-2,9 -1,45 0

PSI1,45 2,9 4,35

-0,2 -0,1 0 0,1 0,2 0,3 0,4

5,8

Intake pipe pressure (BAR)

Sound level at 138 bar (2000 psi)

speed

64

66

68

70

72

dB

(A)

1200 rpm 1500 rpm 1800 rpm

27

BV05single pump

Cartridge V05-42

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

135

0

HP

0 50 100 150 200

100

flow / pressurePSI

l/min

GP

M

300

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

79,2

39,6

0

0 50 100 150 200

1501200 rpm

1500 rpm

1800 rpm

2200 rpm

100 26,4

13,2

81

27

200

200

60

52,880

90

108

54

250 66

10

30

50

70

Cartridge V05-47flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200

50 13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,3

0

HP

0 50 100 150 200

power / pressure

40

120

54,2

27,1

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

0

NM

50

400

600

BAR

39,6

20

200

350

52,8

92,4

135,5

200

60

100250 66

80 108,4

300 79,2162,6

28

BV05single pump

Cartridge V05-50

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

162,6

0

HP

0 50 100 150 200

120

flow / pressurePSI

l/min

GP

M

350

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

92,4

39,6

0

0 50 100 150 200

150

1200 rpm

1500 rpm

1800 rpm

2200 rpm

100 26,4

13,2

81,3

27,1

200

200

60

52,880 108,4

54,2

250 66

300 79,2

100 135,5

Cartridge V05-57flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

0

0 50 100 150 200

50 13,2

BAR

150

26,4

KW

0

BAR

PSI

0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

68

0

HP

0 50 100 150 200

power / pressure

25

125

34

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

0

NM

50

400

600

BAR

39,6

200

400

52,8

105,6

136

200

50

100

250 66

75 102

300 79,2

170350 92,4

BV05single pump

29

Installation dimensions mm (inches)

Approx. weight: 34 Kg. (75 lbs.)

Cartridge V05-60

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900PSI

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200

140

flow / pressurePSI

l/min

GP

M

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

118,8

52,8

26,4

0

0 50 100 150 200

200 1200 rpm

1500 rpm

1800 rpm

2200 rpm

100

13,2

54,4

27,2

450

60

190,4

600

150 39,6

80

200

250 66

100

120 163,2

136

108,8

300

400 105,6

92,4

79,2

350

Spline data(shaft 11 and shaft 90)

Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)

BV05

30

Model code breakdown

BV 05 G * * * * * (L) * (A)

Cartridge type42 47 50 57 60

Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)

Pump type

Outlet port positions(outlet viewed from cover end)

A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet

Mounting(omit if not required)

Shaft options mm (inches)

PORT ORIENTATIONS

Pump series Design Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)

Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C

Shaft01

Shaft11

Shaft90

Shaft86

single pump

BV05

31

single pumpId

. cod

es o

f pum

p co

mpo

nent

s

Par

t N

o.

M80

5025

0

Bo

dy

Par

t N

o.

M80

5027

0

Bea

rin

g

Par

t N

o.

M80

5031

0To

rque

to 3

98 N

m (

3550

lb. i

n.)

Scr

ew

Par

t N

o.

M80

5030

0M

8050

305

M80

5030

1M

8050

306S

haf

t se

al Typ

epr

imar

y in

NB

Rpr

imar

y in

FP

Mse

cond

ary

in N

BR

seco

ndar

y in

FP

M

Pu

mp

sea

l kit

Typ

eN

BR

NB

RF

PM

(V

iton®

)F

PM

(V

iton®

)

Par

t N

o.

M80

5050

0M

8050

501

M80

5050

3M

8050

504

Par

tsse

als

+ 1

sha

ft se

alse

als

+ 2

sha

ft se

als

seal

s +

1 s

haft

seal

seal

s +

2 s

haft

seal

s

Car

trid

ge

Ser

ies

V05

V05

Mo

del

42 47 50 57 60 42 47 50 57 60

Par

t N

o.

V05

4201

0V

0547

030

V05

5005

0V

0557

070

V05

6009

0V

0542

020

V05

4704

0V

0550

060

V05

5708

0V

0560

100

Pu

mp

ro

tat.

right

han

d

left

hand

Mo

del

01 11 86 90

Sh

aft

kit

Par

t N

o.

M80

5060

1M

8050

611

M80

5068

6M

8050

690

Mo

del

01 11 86 90

Sh

aft

Key

Par

t N

o.

K05

0100

0K

0511

000

K05

8600

0K

0590

000

Par

t N

o.

M80

5010

0-

M80

5860

0-

Par

t N

o.

M80

5029

0

See

ger

Par

t N

o.

M80

5028

0

See

ger

Par

t N

o.

M80

5026

0

Co

ver

BV21double pump

32

Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 55 to 134 l/min (from 14to 35 gpm) at 1200 rpm and 7 bar.

General description

Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.

Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).

Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).

Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)

Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with waterbased fluids +15°C to +50°C.

Drive: direct and coaxial by means of a flexible coupling.

Technical characteristcs

Cartridgemodel

Geometricdisplacement

Ratedcapacity

Ratedcapacity

Maximumpressure

Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil

shaft end

V02-12

V02-14

V02-17

V02-19

V02-21

cm3/g

40,1

45,4

55,2

60,1

67,5

(in3/r)

(2.45)

(2.77)

(3.37)

(3.66)

(4.12)

l/min

46,9

52,7

64,2

71,1

79,3

(gpm)

(12)

(14)

(17)

(19)

(21)

l/min

58,8

65,7

80,2

88,7

99,8

(gpm)

(15.5)

(17.4)

(21.2)

(23.4)

(26.4)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

cover end

V01-02

V01-05

V01-08

V01-09

V01-11

V01-12

V01-14

cm3/g

7,2

18,0

27,4

30,1

36,4

39,5

45,9

(in3/r)

(0.44)

(1.10)

(1.67)

(1.83)

(2.22)

(2.41)

(2.79)

l/min

8,3

20,8

31,8

35,1

42,4

46,9

54,9

(gpm)

(2)

(5)

(8)

(9)

(11)

(12)

(14)

l/min

10,4

26,1

39,4

44,1

52,6

58,7

69,6

(gpm)

(2.8)

(6.9)

(10.4)

(11.7)

(13.9)

(15.5)

(18.4)

bar

210

210

210

210

210

160

140

min

600

600

600

600

600

600

600

max

2700

2700

2700

2700

2700

2700

2700

(psi)

(3050)

(3050)

(3050)

(3050)

(3050)

(2300)

(2030)

33

BV21double pump

Shaft end cartridge V02-12

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625

PSI

200

100500

NM

BAR50

150

power / pressure

KW

0

5

10

15

20

25

30

BAR

PSI0 725 1450 2175 2900 3625

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

54,4

40,8

27,2

13,6

0

HP

0 50 100 150 200 250

35

40

flow / pressurePSI

l/min

GP

M

100

80

40

30

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

26

20,8

15,6

0

0 50 100 150 200 250

5,2

90

70

60

50

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

10

10,4

2500 rpm

If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed

Main operating data

max pressure / hydraulic fluid

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

max pres. peak pre. (0,5 sec.max)

Water-in-oilemulsion

250

200

150

100

50

0

BA

R

3625

2900

2175

PS

I

1450

725

0

2000

1600

1200

800600400

0

RP

M

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

Water-in-oilemulsion

1800

1400

200

1000

max speed / hydraulic fluid (with 0 bar in the intake pipe)

speed

60

62

66

68

70

dB

(A)

Sound level at 138 bar (2000 psi)

64

max speed / intake pipe pressure%

co

rrec

tio

n f

acto

r fo

rth

e m

ax s

pee

d

106%

104%

102%

100%

98%

96%

94%

92%

-2,9 -1,45 0

PSI

1,45 2,9 4,35

-0,2 -0,1 0 0,1 0,2 0,3

Intake pipe pressure (BAR)0,4

5,8

1200 rpm 1500 rpm 1800 rpm

34

BV21double pump

Shaft end cartridge V02-14flow / pressure

PSI

l/min G

PM

100

20

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

80

10,4

60

40

20,8

BAR

120

26

5,2

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

600 rpm

54,4

0

HP

0 50 100 150 200 250

power / pressure

10

15

40

50

40,8

27,2

13,6

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625

PSI

100

0

NM

50

150200

BAR

31,2

15,6

68

45

30

25

35

20

50

1000 rpm

Shaft end cartridge V02-17

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625

PSI

250

150

500

NM

BAR50

200

power / pressure

KW

0

10

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

68

40,8

13,6

0

HP

0 50 100 150 200 250

50

60

flow / pressurePSI

l/min

GP

M

140

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

36,4

31,2

26

0

0 50 100 150 200 250

5,2

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

15,6

100

20,8

10,4

30

54,4

27,2

100

35

BV21double pump

Shaft end cartridge V02-19flow / pressure

PSI

l/min G

PM

100

20

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

80

10,4

60

40

20,8

BAR

120

26

5,2

KW

0

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

54,4

0

HP

0 50 100 150 200 250

power / pressure

10

40

60

40,8

27,2

13,6

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

100

0

NM

50

200250

BAR

31,2

15,6

81,6

30

20

50

140

160

36,4

41,6

50 68

150

Shaft end cartridge V02-21

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625

PSI

0

NM

BAR50

200

power / pressure

KW

0

10

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

68

40,8

13,6

0

HP

0 50 100 150 200 250

50

70

flow / pressurePSI

l/min

GP

M

140

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

42

31,5

21

0

0 50 100 150 200 250

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100

10,5

30

54,4

27,2

100

160

180

60

95,2

300

36

BV21double pump

Cartridge V01-02flow / pressure

PSI

l/min G

PM

16

6

2

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

14

2,8

12

8

BAR

20

4,16

KW

0

1

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

8,16

0

HP

0 50 100 150 200 250

power / pressure

3

5

7

8

5,44

2,72

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

100

NM

50

3040

BAR

5,2

3,12

1,04

10,9

4

10

18

2

4

6

20

Cartridge V01-05

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

80

40200

NM

BAR50

60

power / pressure

KW

0

2

4

6

8

10

12

14

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

21,6

16,2

10,8

5,4

0

HP

0 50 100 150 200 250

16

18

flow / pressurePSI

l/min

GP

M

45

35

15

10

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

10,4

7,8

5,2

0

0 50 100 150 200 250

2,6

40

30

25

20

5

1200 rpm

1500 rpm

1800 rpm

2500 rpm

37

BV21double pump

Cartridge V01-08flow / pressure

PSI

l/min G

PM

60

20

10

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50

7,8

40

30

13

BAR

70

15,6

5,2

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

27,2

0

HP

0 50 100 150 200 250

power / pressure

10

15

20

25

20,4

13,6

6,8

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

50

0

NM

50

100

150

BAR

18,2

10,4

2,6

34

Cartridge V01-09

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

50

0

NM

50

100

150

BAR

flow / pressurePSI

l/min G

PM

60

20

10

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

0

0 50 100 150 200 250

50

7,8

40

30

13

80

15,6

5,2

20,8

10,4

2,6

18,270

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

27,2

0

HP

0 50 100 150 200 250

power / pressure

10

15

20

30

20,4

13,6

6,8

40,8

25 34

38

BV21double pump

Cover end cartridge V01-11

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

150

50

0

NM

BAR50

100

power / pressure

KW

0

5

10

15

20

25

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

47,6

34

20,4

6,8

0

HP

0 50 100 150 200 250

30

35

flow / pressurePSI

l/min

GP

M

90

70

30

20

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

21,2

15,9

10,6

0

0 50 100 150 200 250

5,3

80

60

50

40

10

1200 rpm

1500 rpm

1800 rpm

2500 rpm

40,8

27,2

13,6

Cover end cartridge V01-12flow / pressure

PSI

l/min G

PM

90

30

10

0

0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200

70

10,4

60

40

20,8

BAR

100

KW

0

5

BAR

PSI

0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

34

0

HP

0 50 100 150 200

power / pressure

15

20

25

30

27,2

20,4

6,8

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

50

0

NM

50

100

150

BAR

26

15,6

5,2

40,8

80

50

20

10 13,6

BV21

39

Installation dimensions mm (inches)

double pump

Approx. weight: 20,5 Kg. (45 lbs.)

Cover end cartridge V01-14

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

200

100

0

NM

BAR50

150

power / pressure

KW

0

5

10

15

20

25

BAR

PSI0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

40,8

34

20,4

6,8

0

HP

0 50 100 150 200

30

flow / pressurePSI

l/min

GP

M

120

80

20

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

31,8

21,2

10,6

0

0 50 100 150 200

5,3

100

60

401200 rpm

1500 rpm

1800 rpm

2500 rpm

27,2

13,6

26,5

15,9

50

PSI

0 1450 2175 2900725

BV21double pump

40

Model code breakdown

BV 21 G * * * * * * * * (L) * (A)

Cartridge types-shaft end 12 14 17 19 21

-cover end 02 05 08 09 11 12 14

Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)

Pump type

Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet

Mounting(omit if not required)Pump series Design

Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)

Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE B

Cover outlet port positions(outlet viewed from cover end)A = Outlet 135° CCW from inletB = Outlet 45° CCW from inletC = Outlet 45° CW from inletD = Outlet 135° CW from inlet

Shaft options mm (inches)

PORT ORIENTATIONS

Spline data(shaft 11 and shaft 90)

Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 13Pitch 16/32Major dia. 22.00 - 21.90 (0.866 - 0.862)Pitch dia. 20.638 (0.8125)Minor dia. 18.63 - 18.35 (0.733 - 0.722)Wildhaber 11.67 - 11.70 (0.459 - 0.461)

Shaft01

Shaft11

Shaft90

Shaft86

BV21double pump

41

Id. c

odes

of p

ump

com

pone

nts

Par

t N

o.

M80

2001

0

Bo

dy

Par

t N

o.

M80

2003

0

Bea

rin

g

Par

t N

o.

M80

2005

0

See

ger

Par

t N

o.

M80

2004

0

See

ger

Par

t N

o.

M80

2042

0

Torq

ue to

70

Nm

(62

4 lb

. in.

)

Scr

ew

Par

t N

o.

M80

2006

0M

8020

065

M80

2006

1M

8020

066S

haf

t se

al Typ

epr

imar

y in

NB

Rpr

imar

y in

FP

Mse

cond

ary

in N

BR

seco

ndar

y in

FP

M

Pu

mp

sea

l kit

Typ

eN

BR

NB

RF

PM

(V

iton®

)F

PM

(V

iton®

)

Par

t N

o.

M82

1050

0M

8210

501

M82

1050

3M

8210

504

Par

tsse

als

+ 1

sha

ft se

alse

als

+ 2

sha

ft se

als

seal

s +

1 s

haft

seal

seal

s +

2 s

haft

seal

s

Mo

del

01 11 86 90

Sh

aft

kit

Par

t N

o.

M82

1060

1M

8210

611

M82

1068

6M

8210

690

Mo

del

01 11 86 90

Sh

aft

Key

Par

t N

o.

K21

0100

0K

2111

000

K21

8600

0K

2190

000

Par

t N

o.

M80

1010

0-

M80

2860

0-

Par

t N

o.

M80

2012

0

Cov

er

Par

t N

o.

M80

2013

0To

rque

to 1

02 N

m (

910

lb. i

n.)

Scr

ew

Par

t N

o.

M80

2011

0

Inle

t bod

y

Car

trid

ges

Ser

ies

V01

V01

Mo

del

02 05 08 09 11 12 14 02 05 08 09 11 12 14

Par

t N

o.

V01

0200

0V

0105

010

V01

0803

0V

0109

050

V01

1107

0V

0112

090

V01

1411

0V

0102

005

V01

0502

0V

0108

040

V01

0906

0V

0111

080

V01

1210

0V

0114

120

Ser

ies

V02

V02

Mo

del

12 14 17 19 21 12 14 17 19 21

Par

t N

o.

V02

1203

0V

0214

070

V02

1711

0V

0219

150

V02

2119

0

V02

1204

0V

0214

080

V02

1712

0V

0219

160

V02

2120

0

Pu

mp

ro

tati

on

right

han

d

left

hand

cove

r en

dsh

aft e

nd

42

Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 87 to 195 l/min(from 23 to 52 gpm) at 1200 rpm and 7 bar.

General description

Technical characteristcs

Cartridgemodel

Geometricdisplacement

Ratedcapacity

Ratedcapacity

Maximumpressure

Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil

BV41double pump

shaft end

V04-21

V04-25

V04-30

V04-35

V04-38

cm3/g

69,0

81,6

97,7

112,7

121,6

(in3/r)

(4.2)

(5)

(6)

(6.9)

(7.4)

l/min

79,5

94,0

113,8

131,6

139,9

(gpm)

(21)

(25)

(30)

(35)

(38)

l/min

101,4

120,1

141,2

167,2

177,3

(gpm)

(26.8)

(31.7)

(37.3)

(44.1)

(46.8)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.

Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).

Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).

Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)

Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with waterbased fluids +15°C to +50°C.

Drive: direct and coaxial by means of a flexible coupling.

cover end

V01-02

V01-05

V01-08

V01-09

V01-11

V01-12

V01-14

cm3/g

7,2

18,0

27,4

30,1

36,4

39,5

45,9

(in3/r)

(0.44)

(1.10)

(1.67)

(1.83)

(2.22)

(2.41)

(2.79)

l/min

8,3

20,8

31,8

35,1

42,4

46,9

54,9

(gpm)

(2)

(5)

(8)

(9)

(11)

(12)

(14)

l/min

10,4

26,1

39,4

44,1

52,6

58,7

69,6

(gpm)

(2.8)

(6.9)

(10.4)

(11.7)

(13.9)

(15.5)

(18.4)

bar

210

210

210

210

210

160

140

min

600

600

600

600

600

600

600

max

2700

2700

2700

2700

2700

2700

2700

(psi)

(3050)

(3050)

(3050)

(3050)

(3050)

(2300)

(2030)

BV41double pump

43

Shaft end cartridge V04-21

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625

PSI

300

0

NM

BAR50

200

power / pressure

KW

0

10

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm1500 rpm

1200 rpm

1000 rpm

600 rpm

108,8

81,6

0

HP

0 50 100 150 200 250

50

80

flow / pressurePSI

l/min

GP

M

180

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

42

31,5

0

0 50 100 150 200 250

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100

21

10,5

30

54,4

27,2

100

140

160

70

60

If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed

Main operating data

max pressure / hydraulic fluid

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

max pres. peak pres. (0,5 sec.max)

Water-in-oilemulsion

250

200

150

100

50

0

BA

R

3625

2900

2175

PS

I

1450

725

0

2000

1600

1200

800600400

0

RP

M

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

Water-in-oilemulsion

1800

1400

200

1000

max speed / hydraulic fluid (with 0 bar in the intake pipe)

speed

62

64

68

70

72

dB

(A)

Sound level at 138 bar (2000 psi)

66

max speed / intake pipe pressure%

co

rrec

tio

n f

acto

r fo

rth

e m

ax s

pee

d

110%

104%

102%

100%

98%

96%

94%

92%

-2,9 -1,45 0

PSI

1,45 2,9 4,35

-0,2 -0,1 0 0,1 0,2 0,3Intake pipe pressure (BAR)

0,4

5,8

1200 rpm 1500 rpm 1800 rpm

106%

108%

44

BV41double pump

Shaft end cartridge V04-30

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

136

0

HP

0 50 100 150 200 250

120

flow / pressurePSI

l/min

GP

M

250

50

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

66

39,6

0

0 50 100 150 200 250

150

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100 26,4

13,2

81,6

27,2

200

200

60

52,8

80

100

108,8

54,4

Shaft end cartridge V04-25flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50 13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm1500 rpm1200 rpm1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

power / pressure

10

40

90

54,4

27,2

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

1000

NM

50

300400

BAR

39,6

30

20

200

250

52,8

66

50

108,8

200

60

80

70

BV41double pump

45

Shaft end cartridge V04-35flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50

13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

power / pressure

40

120

54,4

27,2

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

0

NM

50

400

600

BAR

39,6

20

200

300

52,8

79,2

136

200

60

100

250 66

80 108,8

Shaft end cartridge V04-38

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625

PSI

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

140

flow / pressurePSI

l/min

GP

M

50

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

79,2

52,8

26,4

0

0 50 100 150 200 250

200

1200 rpm

1500 rpm

1800 rpm

2400 rpm

100

13,2

54,4

27,2

300

60

190,4

600

150 39,6 80

200

250 66

100

120 163,2

136

108,8

BV41double pump

46

Cartridge V01-02flow / pressure

PSI

l/min G

PM

16

6

2

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

14

2,8

12

8

BAR

20

4,16

KW

0

1

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

8,16

0

HP

0 50 100 150 200 250

power / pressure

3

5

7

8

5,44

2,72

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

100

NM

50

3040

BAR

5,2

3,12

1,04

10,9

4

10

18

2

4

6

20

Cartridge V01-05

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

80

40200

NM

BAR50

60

power / pressure

KW

0

2

4

6

8

10

12

14

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

21,6

16,2

10,8

5,4

0

HP

0 50 100 150 200 250

16

18

flow / pressurePSI

l/min

GP

M

45

35

15

10

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

10,4

7,8

5,2

0

0 50 100 150 200 250

2,6

40

30

25

20

5

1200 rpm

1500 rpm

1800 rpm

2500 rpm

BV41double pump

47

Cartridge V01-08flow / pressure

PSI

l/min G

PM

60

20

10

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50

7,8

40

30

13

BAR

70

15,6

5,2

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

27,2

0

HP

0 50 100 150 200 250

power / pressure

10

15

20

25

20,4

13,6

6,8

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

50

0

NM

50

100

150

BAR

18,2

10,4

2,6

34

Cartridge V01-09

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

50

0

NM

50

100

150

BAR

flow / pressurePSI

l/min G

PM

60

20

10

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

0

0 50 100 150 200 250

50

7,8

40

30

13

80

15,6

5,2

20,8

10,4

2,6

18,270

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

27,2

0

HP

0 50 100 150 200 250

power / pressure

10

15

20

30

20,4

13,6

6,8

40,8

25 34

BV41double pump

48

Cover end cartridge V01-11

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

150

50

0

NM

BAR50

100

power / pressure

KW

0

5

10

15

20

25

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

47,6

34

20,4

6,8

0

HP

0 50 100 150 200 250

30

35

flow / pressurePSI

l/min

GP

M

90

70

30

20

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

21,2

15,9

10,6

0

0 50 100 150 200 250

5,3

80

60

50

40

10

1200 rpm

1500 rpm

1800 rpm

2500 rpm

40,8

27,2

13,6

Cover end cartridge V01-12flow / pressure

PSI

l/min G

PM

90

30

10

0

0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200

70

10,4

60

40

20,8

BAR

100

KW

0

5

BAR

PSI

0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

34

0

HP

0 50 100 150 200

power / pressure

15

20

25

30

27,2

20,4

6,8

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

500

NM

50

100

150

BAR

26

15,6

5,2

40,8

80

50

20

10 13,6

BV41double pump

49

Installation dimensions mm (inches)

Approx. weight: 34 Kg. (75 lbs.)

Cover end cartridge V01-14

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

200

100

0

NM

BAR50

150

power / pressure

KW

0

5

10

15

20

25

BAR

PSI0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

40,8

34

20,4

6,8

0

HP

0 50 100 150 200

30

flow / pressurePSI

l/min

GP

M

120

80

20

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

31,8

21,2

10,6

0

0 50 100 150 200

5,3

100

60

401200 rpm

1500 rpm

1800 rpm

2500 rpm

27,2

13,6

26,5

15,9

50

PSI

0 1450 2175 2900725

BV41double pump

Cartridge types-shaft end 21 25 30 35 38

-cover end 02 05 08 09 11 12 14

Shaft options mm (inches)

PORT ORIENTATIONS

Spline data(shaft 11 and shaft 90)

Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)

50

Shaft01

Shaft11

Shaft90

Shaft86

Model code breakdown

BV 41 G * * * * * * * * (L) * (A)

Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)

Pump type

Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet

Mounting(omit if not required)Pump series Design

Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)

Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C

Cover outlet port positions(outlet viewed from cover end)A = Outlet 135° CCW from inletB = Outlet 45° CCW from inletC = Outlet 45° CW from inletD = Outlet 135° CW from inlet

BV41double pump

51

Id. c

odes

of p

ump

com

pone

nts

Par

t N

o.

M80

4016

0

Bea

rin

g

Par

t N

o.

M80

4018

0

See

ger

Mo

del

01 11 86 90

Sh

aft

kit

Par

t N

o.

M84

1060

1M

8410

611

M84

1068

6M

8410

690

Mo

del

01 11 86 90

Sh

aft

Key

Par

t N

o.

K41

0100

0K

4111

000

K41

8600

0K

4190

000

Par

t N

o.

M80

4010

0-

M80

4860

0-

Par

t N

o.

M80

4014

0

Bo

dy

Par

t N

o.

M80

4043

0P

art

No

. M

8020

120

Co

ver

Par

t N

o.

M80

4021

0To

rque

to 2

25 N

m (

2010

lb. i

n.)

Scr

ewP

art

No

. M

8020

420

Torq

ue to

70

Nm

(62

4 lb

. in.

)

Scr

ew

Par

t N

o.

M80

4017

0

See

ger

Par

t N

o.

M80

4019

0M

8040

195

M80

4019

1M

8040

196S

haf

t se

al Typ

epr

imar

y in

NB

Rpr

imar

y in

FP

Mse

cond

ary

in N

BR

seco

ndar

y in

FP

M

Pu

mp

sea

l kit

Typ

eN

BR

NB

RF

PM

(V

iton®

)F

PM

(V

iton®

)

Par

t N

o.

M84

1050

0M

8410

501

M84

1050

3M

8410

504

Par

tsse

als

+ 1

sha

ft se

alse

als

+ 2

sha

ft se

als

seal

s +

1 s

haft

seal

seal

s +

2 s

haft

seal

s

Inle

t bod

y

Car

trid

ges

Ser

ies

V01

V01

Mo

del

02 05 08 09 11 12 14 02 05 08 09 11 12 14

Par

t N

o.

V01

0200

0V

0105

010

V01

0803

0V

0109

050

V01

1107

0V

0112

090

V01

1411

0V

0102

005

V01

0502

0V

0108

040

V01

0906

0V

0111

080

V01

1210

0V

0114

120

Ser

ies

V04

V04

Mo

del

21 25 30 35 38 21 25 30 35 38

Par

t N

o.

V04

2103

0V

0425

070

V04

3011

0V

0435

150

V04

3819

0

V04

2104

0V

0425

080

V04

3012

0V

0435

160

V04

3820

0

Pu

mp

ro

tati

on

right

han

d

left

hand

cove

r en

dsh

aft e

nd

Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 127 to 219 l/min(from 33 to 59 gpm) at 1200 rpm and 7 bar.

General description

BV42double pump

52

Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.

Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).

Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).

Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)

Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water

based fluids +15°C to +50°C.

Drive: direct and coaxial by means of a flexible coupling.

Technical characteristcs

Cartridgemodel

Geometricdisplacement

Ratedcapacity

Ratedcapacity

Maximumpressure

Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil

shaft end

V04-21

V04-25

V04-30

V04-35

V04-38

cm3/g

69,0

81,6

97,7

112,7

121,6

(in3/r)

(4.2)

(5)

(6)

(6.9)

(7.4)

l/min

79,5

94,0

113,8

131,6

139,9

(gpm)

(21)

(25)

(30)

(35)

(38)

l/min

101,4

120,1

141,2

167,2

177,3

(gpm)

(26.8)

(31.7)

(37.3)

(44.1)

(46.8)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

cover end

V02-12

V02-14

V02-17

V02-19

V02-21

cm3/g

40,1

45,4

55,2

60,0

67,5

(in3/r)

(2.45)

(2.77)

(3.37)

(3.66)

(4.12)

l/min

46,9

52,7

64,2

71,0

79,0

(gpm)

(12)

(14)

(17)

(19)

(21)

l/min

58,8

65,7

80,2

88,7

99,8

(gpm)

(15.5)

(17.4)

(21.2)

(23.4)

(26.4)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

53

BV42double pump

If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed

Main operating data

max pressure / hydraulic fluid

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

max pres. peak pres. (0,5 sec.max)

Water-in-oilemulsion

250

200

150

100

50

0

BA

R

3625

2900

2175

PS

I

1450

725

0

2000

1600

1200

800600400

0

RP

M

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

Water-in-oilemulsion

1800

1400

200

1000

max speed / hydraulic fluid (with 0 bar in the intake pipe)

speed

66

68

70

dB

(A)

Sound level at 138 bar (2000 psi)

64

Shaft end cartridge V04-21

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

300

0

NM

BAR50

200

power / pressure

KW

0

10

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm1500 rpm

1200 rpm

1000 rpm

600 rpm

108,8

81,6

0

HP

0 50 100 150 200 250

50

80

flow / pressurePSI

l/min

GP

M

180

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

42

31,5

0

0 50 100 150 200 250

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100

21

10,5

30

54,4

27,2

100

140

160

70

60

max speed / intake pipe pressure%

co

rrec

tio

n f

acto

r fo

rth

e m

ax s

pee

d 106%

104%

102%

100%

98%

96%

94%

92%

-2,9 -1,45 0

PSI

1,45 2,9 4,35

-0,2 -0,1 0 0,1 0,2 0,3Intake pipe pressure (BAR)

0,4

5,8

72

1200 rpm 1500 rpm 1800 rpm

108%

110%

54

BV42double pump

Shaft end cartridge V04-30

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

136

0

HP

0 50 100 150 200 250

120

flow / pressurePSI

l/min

GP

M

250

50

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

66

39,6

0

0 50 100 150 200 250

150

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100 26,4

13,2

81,6

27,2

200

200

60

52,8

80

100

108,8

54,4

Shaft end cartridge V04-25flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50 13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm1500 rpm1200 rpm1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

power / pressure

10

40

90

54,4

27,2

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

1000

NM

50

300400

BAR

39,6

30

20

200

250

52,8

66

50

108,8

200

60

80

70

BV42double pump

55

Shaft end cartridge V04-35flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50

13,2

BAR

150

26,4

KW

0

BAR

PSI

0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

power / pressure

40

120

54,4

27,2

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

0

NM

50

400

600

BAR

39,6

20

200

300

52,8

79,2

136

200

60

100

250 66

80 108,8

Shaft end cartridge V04-38

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

140

flow / pressurePSI

l/min

GP

M

50

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

79,2

52,8

26,4

0

0 50 100 150 200 250

200

1200 rpm

1500 rpm

1800 rpm

2400 rpm

100

13,2

54,4

27,2

300

60

190,4

600

150 39,6 80

200

250 66

100

120 163,2

136

108,8

56

BV42double pump

Cover end cartridge V02-12

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

200

100500

NM

BAR50

150

power / pressure

KW

0

5

10

15

20

25

30

BAR

PSI0 725 1450 2175 2900 3625

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

54,4

40,8

27,2

13,6

0

HP

0 50 100 150 200 250

35

40

flow / pressurePSI

l/min

GP

M

100

80

40

30

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

26

20,8

15,6

0

0 50 100 150 200 250

5,2

90

70

60

50

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

10

10,4

2500 rpm

Cover end cartridge V02-14flow / pressure

PSI

l/min G

PM

100

20

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

80

10,4

60

40

20,8

BAR

120

26

5,2

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

600 rpm

54,4

0

HP

0 50 100 150 200 250

power / pressure

10

15

40

50

40,8

27,2

13,6

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

100

0

NM

50

150200

BAR

31,2

15,6

68

45

30

25

35

20

50

1000 rpm

57

BV42double pump

Cover end cartridge V02-17

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

250

150

500

NM

BAR50

200

power / pressure

KW

0

10

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

68

40,8

13,6

0

HP

0 50 100 150 200 250

50

60

flow / pressurePSI

l/min

GP

M

140

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

36,4

31,2

26

0

0 50 100 150 200 250

5,2

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

15,6

100

20,8

10,4

30

54,4

27,2

100

Cover end cartridge V02-19flow / pressure

PSI

l/min G

PM

100

20

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

80

10,4

60

40

20,8

BAR

120

26

5,2

KW

0

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

54,4

0

HP

0 50 100 150 200 250

power / pressure

10

40

60

40,8

27,2

13,6

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625

PSI

100

0

NM

50

200250

BAR

31,2

15,6

81,6

30

20

50

140

160

36,4

41,6

50 68

150

BV42

58

Installation dimensions mm (inches)

Approx. weight: 34,5 Kg. (76 lbs.)

double pump

Cover end cartridge V02-21

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

0

NM

BAR50

200

flow / pressurePSI

l/min

GP

M

140

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

42

31,5

21

0

0 50 100 150 200 250

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100

10,5

100

160

180

300

power / pressure

KW

0

10

20

40

BAR

PSI

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

68

40,8

13,6

0

HP

0 50 100 150 200 250

50

70

30

54,4

27,2

60

95,2

BV42double pump

59

Cartridge types-shaft end 21 25 30 35 38

-cover end 12 14 17 19 21

Spline data(shaft 11 and shaft 90)

Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)

Shaft options mm (inches)

PORT ORIENTATIONS

Shaft01

Shaft11

Shaft90

Shaft86

Model code breakdown

BV 42 G * * * * * * * * (L) * (A)

Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)

Pump type

Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet

Mounting(omit if not required)Pump series Design

Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)

Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C

Cover outlet port positions(outlet viewed from cover end)A = Outlet 135° CCW from inletB = Outlet 45° CCW from inletC = Outlet 45° CW from inletD = Outlet 135° CW from inlet

BV42double pump

60

Id. c

odes

of p

ump

com

pone

nts

Par

t N

o. M

8040

140

Bo

dy

Par

t N

o.

M80

4016

0

Bea

rin

g

Par

t N

o.

M80

4018

0

See

ger

Par

t N

o.

M80

4017

0

See

ger

Par

t N

o.

M80

4023

0To

rque

to 1

02 N

m (

910

lb. i

n.)

Scr

ew

Par

t N

o.

M80

4019

0M

8040

195

M80

4019

1M

8040

196S

haf

t se

al Typ

epr

imar

y in

NB

Rpr

imar

y in

FP

Mse

cond

ary

in N

BR

seco

ndar

y in

FP

M

Pu

mp

sea

l kit

Typ

eN

BR

NB

RF

PM

(V

iton®

)F

PM

(V

iton®

)

Par

t N

o.

M84

2050

0M

8420

501

M84

2050

3M

8420

504

Par

tsse

als

+ 1

sha

ft se

alse

als

+ 2

sha

ft se

als

seal

s +

1 s

haft

seal

seal

s +

2 s

haft

seal

s

Car

trid

ges

Ser

ies

V02

V02

Mo

del

12 14 17 19 21 12 14 17 19 21

Par

t N

o.

V02

1201

0V

0214

050

V02

1709

0V

0219

130

V02

2117

0V

0212

020

V02

1406

0V

0217

100

V02

1914

0V

0221

180

Ser

ies

V04

V04

Mo

del

21 25 30 35 38 21 25 30 35 38

Par

t N

o.

V04

2103

0V

0425

070

V04

3011

0V

0435

150

V04

3819

0V

0421

040

V04

2508

0V

0430

120

V04

3516

0V

0438

200

Pu

mp

ro

tati

on

right

han

d

left

hand

cove

r en

dsh

aft e

nd

Par

t N

o.

M80

5035

0

Co

ver

Par

t N

o.

M80

4022

0To

rque

to 2

25 N

m (

2010

lb. i

n.)

Scr

ew

Par

t N

o.

M80

4024

0

Mo

del

01 11 86 90

Sh

aft

Key

Par

t N

o.

M80

4010

0-

M80

4860

0-

Mo

del

01 11 86 90

Sh

aft

kit

Par

t N

o.

M84

2060

1M

8420

611

M84

2068

6M

8420

690

Inte

l bod

y

Par

t N

o.

K42

0100

0K

4211

000

K42

8600

0K

4290

000

BV51double pump

Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 172 to 285 l/min(from 44 to 74 gpm) at 1200 rpm and 7 bar.

General description

61

Technical characteristcs

Cartridgemodel

Geometricdisplacement

Ratedcapacity

Ratedcapacity

Maximumpressure

Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar awith mineral oil

Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.

Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).

Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).

Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)

Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with waterbased fluids +15°C to +50°C.

Drive: direct and coaxial by means of a flexible coupling.

shaft end

V05-42

V05-47

V05-50

V05-57

V05-60

cm3/g

138,6

153,5

162,2

183,4

193,4

(in3/r)

(8.46)

(9.4)

(9.9)

(11.2)

(11.8)

l/min

164

180

189

217

230

(gpm)

(42)

(47)

(50)

(57)

(60)

l/min

203,4

222,7

234

267

285

(gpm)

(53.7)

(58.8)

(61.8)

(71.2)

(75.3)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

cover end

V01-02

V01-05

V01-08

V01-09

V01-11

V01-12

V01-14

cm3/g

7,2

18,0

27,4

30,1

36,4

39,5

45,9

(in3/r)

(0.44)

(1.10)

(1.67)

(1.83)

(2.22)

(2.41)

(2.79)

l/min

8,3

20,8

31,8

35,1

42,4

46,9

54,9

(gpm)

(2)

(5)

(8)

(9)

(11)

(12)

(14)

l/min

10,4

26,1

39,4

44,1

52,6

58,7

69,6

(gpm)

(2.8)

(6.9)

(10.4)

(11.7)

(13.9)

(15.5)

(18.4)

bar

210

210

210

210

210

160

140

min

600

600

600

600

600

600

600

max

2700

2700

2700

2700

2700

2700

2700

(psi)

(3050)

(3050)

(3050)

(3050)

(3050)

(2300)

(2030)

62

BV51double pump

If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed

Main operating data

max pressure / hydraulic fluid

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

max pres. peak pres. (0,5 sec.max)

Water-in-oilemulsion

250

200

150

100

50

0

BA

R

3625

2900

2175

PS

I

1450

725

0

2000

1600

1200

800600400

0

RP

M

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

Water-in-oilemulsion

1800

1400

200

1000

max speed / hydraulic fluid (with 0 bar in the intake pipe)

speed

65

69

71

73

dB

(A)

Sound level at 138 bar (2000 psi)

67

Shaft end cartridge V05-42

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

135

0

HP

0 50 100 150 200

100

flow / pressurePSI

l/min

GP

M

300

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

79,2

39,6

0

0 50 100 150 200

1501200 rpm

1500 rpm

1800 rpm

2200 rpm

100 26,4

13,2

81

27

200

200

60

52,880

90

108

54

250 66

10

30

50

70

1200 rpm 1500 rpm 1800 rpm

max speed / intake pipe pressure%

co

rrec

tio

n f

acto

r fo

rth

e m

ax s

pee

d

120%

115%

110%

105%

100%

95%

90%

-2,9 -1,45 0

PSI

1,45 2,9 4,35

-0,2 -0,1 0 0,1 0,2 0,3Intake pipe pressure (BAR)

0,4

5,8

Shaft end cartridge V05-47flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200

50 13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,3

0

HP

0 50 100 150 200

power / pressure

40

120

54,2

27,1

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900PSI

0

NM

50

400

600

BAR

39,6

20

200

350

52,8

92,4

135,5

200

60

100250 66

80 108,4

300 79,2162,6

BV51double pump

63

Shaft end cartridge V05-50

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

162,6

0

HP

0 50 100 150 200

120

flow / pressurePSI

l/min

GP

M

350

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

92,4

39,6

0

0 50 100 150 200

150

1200 rpm

1500 rpm

1800 rpm

2200 rpm

100 26,4

13,2

81,3

27,1

200

200

60

52,880 108,4

54,2

250 66

300 79,2

100 135,5

BV51double pump

64

Shaft end cartridge V05-57flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

0

0 50 100 150 200

50 13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

68

0

HP

0 50 100 150 200

power / pressure

25

125

34

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900PSI

0

NM

50

400

600

BAR

39,6

200

400

52,8

105,6

136

200

50

100

250 66

75 102

300 79,2

170350 92,4

Shaft end cartridge V05-60

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200

140

flow / pressurePSI

l/min

GP

M

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

118,8

52,8

26,4

0

0 50 100 150 200

200 1200 rpm

1500 rpm

1800 rpm

2200 rpm

100

13,2

54,4

27,2

450

60

190,4

600

150 39,6

80

200

250 66

100

120 163,2

136

108,8

300

400 105,6

92,4

79,2

350

BV51double pump

65

Cartridge V01-02flow / pressure

PSI

l/min G

PM

16

6

2

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

14

2,8

12

8

BAR

20

4,16

KW

0

1

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

8,16

0

HP

0 50 100 150 200 250

power / pressure

3

5

7

8

5,44

2,72

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

100

NM

50

3040

BAR

5,2

3,12

1,04

10,9

4

10

18

2

4

6

20

Cartridge V01-05

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

80

40200

NM

BAR50

60

power / pressure

KW

0

2

4

6

8

10

12

14

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

21,6

16,2

10,8

5,4

0

HP

0 50 100 150 200 250

16

18

flow / pressurePSI

l/min

GP

M

45

35

15

10

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

10,4

7,8

5,2

0

0 50 100 150 200 250

2,6

40

30

25

20

5

1200 rpm

1500 rpm

1800 rpm

2500 rpm

BV51double pump

66

Cartridge V01-08flow / pressure

PSI

l/min G

PM

60

20

10

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50

7,8

40

30

13

BAR

70

15,6

5,2

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

27,2

0

HP

0 50 100 150 200 250

power / pressure

10

15

20

25

20,4

13,6

6,8

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

50

0

NM

50

100

150

BAR

18,2

10,4

2,6

34

Cartridge V01-09

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

50

0

NM

50

100

150

BAR

flow / pressurePSI

l/min G

PM

60

20

10

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

0

0 50 100 150 200 250

50

7,8

40

30

13

80

15,6

5,2

20,8

10,4

2,6

18,270

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

27,2

0

HP

0 50 100 150 200 250

power / pressure

10

15

20

30

20,4

13,6

6,8

40,8

25 34

Cover end cartridge V01-11

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

150

50

0

NM

BAR50

100

power / pressure

KW

0

5

10

15

20

25

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

47,6

34

20,4

6,8

0

HP

0 50 100 150 200 250

30

35

flow / pressurePSI

l/min

GP

M

90

70

30

20

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

21,2

15,9

10,6

0

0 50 100 150 200 250

5,3

80

60

50

40

10

1200 rpm

1500 rpm

1800 rpm

2500 rpm

40,8

27,2

13,6

Cover end cartridge V01-12flow / pressure

PSI

l/min G

PM

90

30

10

0

0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200

70

10,4

60

40

20,8

BAR

100

KW

0

5

BAR

PSI

0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

34

0

HP

0 50 100 150 200

power / pressure

15

20

25

30

27,2

20,4

6,8

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

50

0

NM

50

100

150

BAR

26

15,6

5,2

40,8

80

50

20

10 13,6

67

BV51double pump

Cover end cartridge V01-14

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

200

100

0

NM

BAR50

150

power / pressure

KW

0

5

10

15

20

25

BAR

PSI0 725 1450 2175 2900

2500 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

40,8

34

20,4

6,8

0

HP

0 50 100 150 200

30

flow / pressurePSI

l/min

GP

M

120

80

20

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

31,8

21,2

10,6

0

0 50 100 150 200

5,3

100

60

401200 rpm

1500 rpm

1800 rpm

2500 rpm

27,2

13,6

26,5

15,9

50

68

Installation dimensions mm (inches)

Approx. weight: 43 Kg. (95 lbs.)

BV51double pump

PSI0 1450 2175 2900725

Spline data(shaft 11 and shaft 90)

Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)

Shaft options mm (inches)

PORT ORIENTATIONS

Cartridge types-shaft end 42 47 50 57 60

-cover end 02 05 08 09 11 12 14

BV51double pump

69

Shaft01

Shaft11

Shaft90

Shaft86

Model code breakdown

BV 51 G * * * * * * * * (L) * (A)

Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)

Pump type

Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet

Mounting(omit if not required)Pump series Design

Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)

Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C

Cover outlet port positions(outlet viewed from cover end)A = Outlet 135° CCW from inletB = Outlet 45° CCW from inletC = Outlet 45° CW from inletD = Outlet 135° CW from inlet

BV51double pump

70

Id. c

odes

of p

ump

com

pone

nts

Par

t N

o.

M80

5025

0

Bo

dy

Par

t N

o.

M80

5027

0

Bea

rin

g

Par

t N

o.

M80

5029

0

See

ger

Par

t N

o.

M80

2042

0To

rque

to 7

0 N

m (

624

lb. i

n.)

Scr

ew

Par

t N

o.

M80

5030

0M

8050

305

M80

5030

1M

8050

306S

haf

t se

al Typ

epr

imar

y in

NB

Rpr

imar

y in

FP

Mse

cond

ary

in N

BR

seco

ndar

y in

FP

M

Pu

mp

sea

l kit

Typ

eN

BR

NB

RF

PM

(V

iton®

)F

PM

(V

iton®

)

Par

t N

o.

M85

1050

0M

8510

501

M85

1050

3M

8510

504

Par

tsse

als

+ 1

sha

ft se

alse

als

+ 2

sha

ft se

als

seal

s +

1 s

haft

seal

seal

s +

2 s

haft

seal

s

Par

t N

o.

M80

2012

0

Cov

erP

art

No

. M

8050

390

Mo

del

01 11 86 90

Sh

aft

Key

Par

t N

o.

K51

0100

0K

5111

000

K51

8600

0K

5190

000

Par

t N

o.

M80

5010

0-

M80

5860

0-

Mo

del

01 11 86 90

Sh

aft

kit

Par

t N

o.

M85

1060

1M

8510

611

M85

1068

6M

8510

690

Inle

t bod

y

See

ger

Par

t N

o.

M80

5028

0

Par

t N

o.

M80

5032

0To

rque

to 3

98 N

m (

3550

lb. i

n.)

Scr

ew

Car

trid

ges

Ser

ies

V01

V01

Mo

del

02 05 08 09 11 12 14 02 05 08 09 11 12 14

Par

t N

o.

V01

0200

0V

0105

010

V01

0803

0V

0109

050

V01

1107

0V

0112

090

V01

1411

0V

0102

005

V01

0502

0V

0108

040

V01

0906

0V

0111

080

V01

1210

0V

0114

120

Ser

ies

V05

V05

Mo

del

42 47 50 57 60 42 47 50 57 60

Par

t N

o.

V05

4201

0V

0547

030

V05

5005

0V

0557

070

V05

6009

0

V05

4202

0V

0547

040

V05

5006

0V

0557

080

V05

6010

0

Pu

mp

ro

tati

on

right

han

d

left

hand

cove

r en

dsh

aft e

nd

Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 211 to 309 l/min(from 54 to 81 gpm) at 1200 rpm and 7 bar.

General description

Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.

Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).

Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).

Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)

Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water

based fluids +15°C to +50°C.

Drive: direct and coaxial by means of a flexible coupling.

Technical characteristcs

Cartridgemodel

Geometricdisplacement

Ratedcapacity

Ratedcapacity

Maximumpressure

Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil

BV52double pump

71

shaft end

V05-42

V05-47

V05-50

V05-57

V05-60

cm3/g

138,6

153,5

162,2

183,4

193,4

(in3/r)

(8.46)

(9.4)

(9.9)

(11.2)

(11.8)

l/min

164

180

189

217

230

(gpm)

(42)

(47)

(50)

(57)

(60)

l/min

203,4

222,7

234

267

285

(gpm)

(53.7)

(58.8)

(61.8)

(71.2)

(75.3)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

cover end

V02-12

V02-14

V02-17

V02-19

V02-21

cm3/g

40,1

45,4

55,2

60,0

67,5

(in3/r)

(2.45)

(2.77)

(3.37)

(3.66)

(4.12)

l/min

46,9

52,7

64,2

71,0

79,0

(gpm)

(12)

(14)

(17)

(19)

(21)

l/min

58,8

65,7

80,2

88,7

99,8

(gpm)

(15.5)

(17.4)

(21.2)

(23.4)

(26.4)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

BV52double pump

72

If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed

Main operating data

max pressure / hydraulic fluid

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

max pres. peak pres. (0,5 sec.max)

Water-in-oilemulsion

250

200

150

100

50

0

BA

R

3625

2900

2175

PS

I

1450

725

0

2000

1600

1200

800600400

0

RP

M

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

Water-in-oilemulsion

1800

1400

200

1000

max speed / hydraulic fluid (with 0 bar in the intake pipe)

speed

66

68

72

74

dB

(A)

Sound level at 138 bar (2000 psi)

70

Shaft end cartridge V05-42

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

135

0

HP

0 50 100 150 200

100

flow / pressurePSI

l/min

GP

M

300

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

79,2

39,6

0

0 50 100 150 200

1501200 rpm

1500 rpm

1800 rpm

2200 rpm

100 26,4

13,2

81

27

200

200

60

52,880

90

108

54

250 66

10

30

50

70

1200 rpm 1500 rpm 1800 rpm

max speed / intake pipe pressure%

co

rrec

tio

n f

acto

r fo

rth

e m

ax s

pee

d

120%

115%

110%

105%

100%

95%

90%

-2,9 -1,45 0

PSI

1,45 2,9 4,35

-0,2 -0,1 0 0,1 0,2 0,3Intake pipe pressure (BAR)

0,4

5,8

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

BV52double pump

73

Shaft end cartridge V05-50

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI

0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

162,6

0

HP

0 50 100 150 200

120

flow / pressurePSI

l/min

GP

M

350

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

92,4

39,6

0

0 50 100 150 200

150

1200 rpm

1500 rpm

1800 rpm

2200 rpm

100 26,4

13,2

81,3

27,1

200

200

60

52,880 108,4

54,2

250 66

300 79,2

100 135,5

Shaft end cartridge V05-47flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200

50 13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,3

0

HP

0 50 100 150 200

power / pressure

40

120

54,2

27,1

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

0

NM

50

400

600

BAR

39,6

20

200

350

52,8

92,4

135,5

200

60

100250 66

80 108,4

300 79,2162,6

74

BV52double pump

Shaft end cartridge V05-57flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

0

0 50 100 150 200

50 13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

68

0

HP

0 50 100 150 200

power / pressure

25

125

34

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900PSI

0

NM

50

400

600

BAR

39,6

200

400

52,8

105,6

136

200

50

100

250 66

75 102

300 79,2

170350 92,4

Shaft end cartridge V05-60

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200

140

flow / pressurePSI

l/min

GP

M

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

118,8

52,8

26,4

0

0 50 100 150 200

200 1200 rpm

1500 rpm

1800 rpm

2200 rpm

100

13,2

54,4

27,2

450

60

190,4

600

150 39,6

80

200

250 66

100

120 163,2

136

108,8

300

400 105,6

92,4

79,2

350

BV52double pump

75

Cover end cartridge V02-12

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

200

100500

NM

BAR50

150

power / pressure

KW

0

5

10

15

20

25

30

BAR

PSI0 725 1450 2175 2900 3625

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

54,4

40,8

27,2

13,6

0

HP

0 50 100 150 200 250

35

40

flow / pressurePSI

l/min

GP

M

100

80

40

30

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

26

20,8

15,6

0

0 50 100 150 200 250

5,2

90

70

60

50

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

10

10,4

2500 rpm

Cover end cartridge V02-14flow / pressure

PSI

l/min G

PM

100

20

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

80

10,4

60

40

20,8

BAR

120

26

5,2

KW

0

5

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

600 rpm

54,4

0

HP

0 50 100 150 200 250

power / pressure

10

15

40

50

40,8

27,2

13,6

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

100

0

NM

50

150200

BAR

31,2

15,6

68

45

30

25

35

20

50

1000 rpm

double pump

76

BV52

Cover end cartridge V02-17

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

250

150

500

NM

BAR50

200

power / pressure

KW

0

10

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

68

40,8

13,6

0

HP

0 50 100 150 200 250

50

60

flow / pressurePSI

l/min

GP

M

140

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

36,4

31,2

26

0

0 50 100 150 200 250

5,2

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

15,6

100

20,8

10,4

30

54,4

27,2

100

Cover end cartridge V02-19flow / pressure

PSI

l/min G

PM

100

20

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

80

10,4

60

40

20,8

BAR

120

26

5,2

KW

0

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

54,4

0

HP

0 50 100 150 200 250

power / pressure

10

40

60

40,8

27,2

13,6

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

100

0

NM

50

200250

BAR

31,2

15,6

81,6

30

20

50

140

160

36,4

41,6

50 68

150

BV52

77

Installation dimensions mm (inches)

Approx. weight: 46 Kg. (101 lbs.)

double pump

Cover end cartridge V02-21

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

0

NM

BAR50

200

flow / pressurePSI

l/min

GP

M

140

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

42

31,5

21

0

0 50 100 150 200 250

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100

10,5

100

160

180

300

power / pressure

KW

0

10

20

40

BAR

PSI

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

68

40,8

13,6

0

HP

0 50 100 150 200 250

50

70

30

54,4

27,2

60

95,2

78

BV52double pump

Cartridge types-shaft end 42 47 50 57 60

-cover end 12 14 17 19 21

Spline data(shaft 11 and shaft 90)

Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)

Shaft options mm (inches)

PORT ORIENTATIONS

Shaft01

Shaft11

Shaft90

Shaft86

Model code breakdown

BV 52 G * * * * * * * * (L) * (A)

Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)

Pump type

Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet

Mounting(omit if not required)Pump series Design

Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)

Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C

Cover outlet port positions(outlet viewed from cover end)A = Outlet 135° CCW from inletB = Outlet 45° CCW from inletC = Outlet 45° CW from inletD = Outlet 135° CW from inlet

79

BV52double pumpId

. cod

es o

f pum

p co

mpo

nent

s

Par

t N

o.

M80

5029

0

See

ger

Par

t N

o.

M80

5025

0

Bo

dy

Car

trid

ges

Ser

ies

V02

V02

Mo

del

12 14 17 19 21 12 14 17 19 21

Par

t N

o.

V02

1201

0V

0214

050

V02

1709

0V

0219

130

V02

2117

0V

0212

020

V02

1406

0V

0217

100

V02

1914

0V

0221

180

Ser

ies

V05

V05

Mo

del

42 47 50 57 60 42 47 50 57 60

Par

t N

o.

V05

4201

0V

0547

030

V05

5005

0V

0557

070

V05

6009

0V

0542

020

V05

4704

0V

0550

060

V05

5708

0V

0560

100

Pu

mp

ro

tati

on

right

han

d

left

hand

cove

r en

dsh

aft e

ndM

od

el01 11 86 90

Sh

aft

kit

Par

t N

o.

M85

2060

1M

8520

611

M85

2068

6M

8520

690

Mo

del

01 11 86 90

Sh

aft

Key

Par

t N

o.

K52

0100

0K

5211

000

K52

8600

0K

5290

000

Par

t N

o.

M80

5010

0-

M80

5860

0- P

art

No

.M

8050

300

M80

5030

5M

8050

301

M80

5030

6Sh

aft

seal Ty

pe

prim

ary

in N

BR

prim

ary

in F

PM

seco

ndar

y in

NB

Rse

cond

ary

in F

PM

Par

t N

o.

M80

4023

0To

rque

to 1

02 N

m (

910

lb. i

n.)

Scr

ewP

art

No

. M

8050

330

Torq

ue to

398

Nm

(35

50 lb

. in.

)

Scr

ew

Par

t N

o.

M80

5028

0

See

ger

Pu

mp

sea

l kit

Typ

eN

BR

NB

RF

PM

(V

iton®

)F

PM

(V

iton®

)

Par

t N

o.

M85

2050

0M

8520

501

M85

2050

3M

8520

504

Par

tsse

als

+ 1

sha

ft se

alse

als

+ 2

sha

ft se

als

seal

s +

1 s

haft

seal

seal

s +

2 s

haft

seal

s

Par

t N

o.

M80

5027

0

Bea

rin

g

Par

t N

o.

M80

5035

0

Cov

er

Par

t N

o.

M80

5040

0

Inle

t bod

y

80

BV54double pump

Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 244 to 370 l/min(from 63 to 98 gpm) at 1200 rpm and 7 bar.

General description

Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.

Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).

Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).

Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)

Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water

based fluids +15°C to +50°C.

Drive: direct and coaxial by means of a flexible coupling.

Technical characteristcs

Cartridgemodel

Geometricdisplacement

Ratedcapacity

Ratedcapacity

Maximumpressure

Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil

cover end

V04-21

V04-25

V04-30

V04-35

V04-38

cm3/g

69,0

81,6

97,7

112,7

121,6

(in3/r)

(4.2)

(5)

(6)

(6.9)

(7.4)

l/min

79,5

94,0

113,8

131,6

139,9

(gpm)

(21)

(25)

(30)

(35)

(38)

l/min

101,4

120,1

141,2

167,2

177,3

(gpm)

(26.8)

(31.7)

(37.3)

(44.1)

(46.8)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

shaft end

V05-42

V05-47

V05-50

V05-57

V05-60

cm3/g

138,6

153,5

162,2

183,4

193,4

(in3/r)

(8.46)

(9.4)

(9.9)

(11.2)

(11.8)

l/min

164

180

189

217

230

(gpm)

(42)

(47)

(50)

(57)

(60)

l/min

203,4

222,7

234

267

285

(gpm)

(53.7)

(58.8)

(61.8)

(71.2)

(75.3)

bar

175

175

175

175

175

min

600

600

600

600

600

max

1800

1800

1800

1800

1800

(psi)

(2538)

(2538)

(2538)

(2538)

(2538)

BV54double pump

81

If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed

Main operating data

max pressure / hydraulic fluid

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

max pres. peak pres. (0,5 sec.max)

Water-in-oilemulsion

250

200

150

100

50

0

BA

R

3625

2900

2175

PS

I

1450

725

0

2000

1600

1200

800600400

0

RP

M

Antiwear industrialhydraulic oil

Syntetic fireresistant fluid

Waterglycol

Water-in-oilemulsion

1800

1400

200

1000

max speed / hydraulic fluid (with 0 bar in the intake pipe)

speed

67

69

73

75

dB

(A)

Sound level at 138 bar (2000 psi)

71

Shaft end cartridge V05-42

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

135

0

HP

0 50 100 150 200

100

flow / pressurePSI

l/min

GP

M

300

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

79,2

39,6

0

0 50 100 150 200

1501200 rpm

1500 rpm

1800 rpm

2200 rpm

100 26,4

13,2

81

27

200

200

60

52,880

90

108

54

250 66

10

30

50

70

1200 rpm 1500 rpm 1800 rpm

max speed / intake pipe pressure%

co

rrec

tio

n f

acto

r fo

rth

e m

ax s

pee

d

120%

115%

110%

105%

100%

95%

90%

-2,9 -1,45 0

PSI

1,45 2,9 4,35

-0,2 -0,1 0 0,1 0,2 0,3Intake pipe pressure (BAR)

0,4

5,8

82

BV54double pump

Shaft end cartridge V05-47flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200

50 13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,3

0

HP

0 50 100 150 200

power / pressure

40

120

54,2

27,1

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

0

NM

50

400

600

BAR

39,6

20

200

350

52,8

92,4

135,5

200

60

100250 66

80 108,4

300 79,2162,6

Shaft end cartridge V05-50

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

162,6

0

HP

0 50 100 150 200

120

flow / pressurePSI

l/min

GP

M

350

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

92,4

39,6

0

0 50 100 150 200

150

1200 rpm

1500 rpm

1800 rpm

2200 rpm

100 26,4

13,2

81,3

27,1

200

200

60

52,880 108,4

54,2

250 66

300 79,2

100 135,5

BV54double pump

83

Shaft end cartridge V05-57flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm1000 rpm

600 rpm

0

0 50 100 150 200

50 13,2

BAR

150

26,4

KW

0

BAR

PSI

0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

68

0

HP

0 50 100 150 200

power / pressure

25

125

34

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

0

NM

50

400

600

BAR

39,6

200

400

52,8

105,6

136

200

50

100

250 66

75 102

300 79,2

170350 92,4

Shaft end cartridge V05-60

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200

input torque / pressure

0 725 1450 2175 2900

PSI

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900

2200 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200

140

flow / pressurePSI

l/min

GP

M

50

0

0 725 1450 2175 2900

1000 rpm

600 rpm

BAR

118,8

52,8

26,4

0

0 50 100 150 200

200 1200 rpm

1500 rpm

1800 rpm

2200 rpm

100

13,2

54,4

27,2

450

60

190,4

600

150 39,6

80

200

250 66

100

120 163,2

136

108,8

300

400 105,6

92,4

79,2

350

84

BV54double pump

Cover end cartridge V04-21

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

300

0

NM

BAR50

200

power / pressure

KW

0

10

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm1500 rpm

1200 rpm

1000 rpm

600 rpm

108,8

81,6

0

HP

0 50 100 150 200 250

50

80

flow / pressurePSI

l/min

GP

M

180

80

40

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

42

31,5

0

0 50 100 150 200 250

120

60

20

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100

21

10,5

30

54,4

27,2

100

140

160

70

60

Cover end cartridge V04-25flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50 13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm1500 rpm1200 rpm1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

power / pressure

10

40

90

54,4

27,2

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

1000

NM

50

300400

BAR

39,6

30

20

200

250

52,8

66

50

108,8

200

60

80

70

BV54double pump

85

Cover end cartridge V04-30

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

600

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900 3625

2500 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

136

0

HP

0 50 100 150 200 250

120

flow / pressurePSI

l/min

GP

M

250

50

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

66

39,6

0

0 50 100 150 200 250

150

1200 rpm

1500 rpm

1800 rpm

2500 rpm

100 26,4

13,2

81,6

27,2

200

200

60

52,8

80

100

108,8

54,4

Cover end cartridge V04-35flow / pressure

PSI

l/min G

PM

100

0

0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm

1200 rpm

1000 rpm

600 rpm

0

0 50 100 150 200 250

50

13,2

BAR

150

26,4

KW

0

BAR

PSI0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

power / pressure

40

120

54,4

27,2

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

0

NM

50

400

600

BAR

39,6

20

200

300

52,8

79,2

136

200

60

100

250 66

80 108,8

86

BV54double pump

Installation dimensions mm (inches)

Approx. weight: 54 Kg. (118 lbs.)

Cover end cartridge V04-38

Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR

0 100 150 200 250

input torque / pressure

0 725 1450 2175 2900 3625PSI

0

NM

BAR50

400

power / pressure

KW

0

20

40

BAR

PSI0 725 1450 2175 2900 3625

2400 rpm

1800 rpm

1500 rpm1200 rpm

1000 rpm

600 rpm

81,6

0

HP

0 50 100 150 200 250

140

flow / pressurePSI

l/min

GP

M

50

0

0 725 1450 2175 2900 3625

1000 rpm

600 rpm

BAR

79,2

52,8

26,4

0

0 50 100 150 200 250

200

1200 rpm

1500 rpm

1800 rpm

2400 rpm

100

13,2

54,4

27,2

300

60

190,4

600

150 39,6 80

200

250 66

100

120 163,2

136

108,8

BV54double pump

87

Cartridge types-shaft end 42 47 50 57 60

-cover end 21 25 30 35 38

Spline data(shaft 11 and shaft 90)

Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)

Shaft options mm (inches)

PORT ORIENTATIONS

Shaft01

Shaft11

Shaft90

Shaft86

Model code breakdown

BV 54 G * * * * * * * * (L) * (A)

Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)

Pump type

Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet

Mounting(omit if not required)Pump series Design

Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)

Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C

Cover outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet

88

BV54double pump

Par

t N

o.

M80

5025

0

Bo

dy

Par

t N

o.

M80

5027

0

Bea

rin

g

Par

t N

o.

M80

5029

0

See

ger

Par

t N

o.

M80

5030

0M

8050

305

M80

5030

1M

8050

306Sh

aft

seal Ty

pe

prim

ary

in N

BR

prim

ary

in F

PM

seco

ndar

y in

NB

Rse

cond

ary

in F

PM

Pu

mp

sea

l kit

Typ

eN

BR

NB

RF

PM

(V

iton®

)F

PM

(V

iton®

)

Par

t N

o.

M85

4050

0M

8540

501

M85

4050

3M

8540

504

Par

tsse

als

+ 1

sha

ft se

alse

als

+ 2

sha

ft se

als

seal

s +

1 s

haft

seal

seal

s +

2 s

haft

seal

s

Car

trid

ges

Ser

ies

V04

V04

Mo

del

21 25 30 35 38 21 25 30 35 38

Par

t N

o.

V04

2101

0V

0425

050

V04

3009

0V

0435

130

V04

3817

0V

0421

020

V04

2506

0V

0430

100

V04

3514

0V

0438

180

Mo

del

01 11 86 90

Sh

aft

kit

Par

t N

o.

M85

4060

1M

8540

611

M85

4068

6M

8540

690

Mo

del

01 11 86 90

Sh

aft

Key

Par

t N

o.

K54

0100

0K

5411

000

K54

8600

0K

5490

000

Par

t N

o.

M80

5010

0-

M80

5860

0-

Ser

ies

V05

V05

Mo

del

42 47 50 57 60 42 47 50 57 60

Par

t N

o.

V05

4201

0V

0547

030

V05

5005

0V

0557

070

V05

6009

0V

0542

020

V05

4704

0V

0550

060

V05

5708

0V

0560

100

Pu

mp

ro

tati

on

right

han

d

left

hand

cove

r en

dsh

aft e

nd

Par

t N

o.

M80

5041

0

Par

t N

o.

M80

5038

0To

rque

to 3

98 N

m (

3550

lb. i

n.)

Scr

ew

Par

t N

o.

M80

5036

0

Co

ver

Par

t N

o.

M80

5028

0

See

ger

Inle

t bod

y

89

BVId

. cod

es o

f car

trid

ge k

it co

mpo

nent

s

6

5

8

7

4

3

1

92

90

BV

02L6

2092

00L6

2093

00L6

2091

00L7

2090

02

05L6

2092

00L6

2093

00L6

2091

00L7

2090

05

08L6

2092

00L6

2093

00L6

2091

00L7

2090

08

V01

09L6

2092

00L6

2093

00L6

2091

00L7

2090

09L6

2001

00L6

2011

00L6

2006

00

11L6

2009

00L6

2008

00L6

2002

00L6

2003

00L6

2012

00L7

2010

11L6

2021

00 (

FP

M)

123,

6 N

mL6

2002

00L6

2003

00L6

2012

00L7

2010

12

14(3

2 lb

. in.

)L6

2002

00L6

2003

00L6

2012

00L7

2010

14

12L6

2510

12

14L6

2510

14

V02

17L6

2509

00L6

2508

00L6

2502

00L6

2503

00L6

2512

00L6

2510

17L6

2501

00L6

2511

00L7

2506

00

195,

5 N

mL6

2510

19L6

2521

00 (

FP

M)

21(4

9 lb

. in.

)L6

2510

21

21

L635

1021

25L6

3510

25

V04

30L6

3509

00L6

3508

00L6

3502

00L6

3503

00L6

3512

00L6

3510

30L6

3501

00L6

3511

00L7

3506

00

3512

,6 N

mL6

3510

35L6

3521

00 (

FP

M)

38(1

12 lb

.in)

L635

1038

42L6

4510

42

47L6

4510

47

V05

50L6

4509

00L6

4508

00L6

4502

00L6

4503

00L6

4512

00L6

4510

50L6

4501

00L6

4511

00L7

4506

00

5712

,6 N

mL6

4510

57L6

4521

00 (

FP

M)

60(1

12 lb

.in)

L645

1060

( *

) N

ote:

The

cov

er e

nd c

artr

idge

of t

he d

oubl

e pu

mp

is w

ithou

t bus

hing

.

12

34

56

78

9

Car

trid

ge

Scr

ew

Ser

ies

Mo

del

Pin

Inle

tsu

pp

ort

pla

te

Ro

tor

Van

e an

din

sert

kit

(12+

12 p

cs.)

Rin

gO

utl

etsu

pp

ort

pla

te

Sea

l kit

(4 p

cs.)

Bu

shin

g(

* )

91© 2008 B&C

Maximum speed: the maximum speeds given in this catalogue are valid for an atmospheric pressure of 1 bar (14.7 psi)and with ambient temperature in the range of +30°C to +50°C. Higher speeds than those given cause a reduction in thevolumetric efficiency, due to cavitation phenomena in the inlet area inside the pump. Sustained excess speed causes arapid deterioration of the internal components reducing the lifetime of the cartridge.

Minimum speed: In general, the min. speed for all pumps is 600 rpm. However, it is possible to operate at lower speedswith certain pump configurations and with appropriate operating temperatures.

Inlet pressure: the inlet pressure, measured at the inlet port, should remain within the prescribed limits. Note that pressureslower than minimum limit cause cavitation and pressures above the maximum limit cause abnormal loads on the shaftand the bearings. In both cases this causes a significant reduction in the lifetime of the cartridge.

Maximum outlet pressure: the maximum outlet pressure is different for each type of fluid used as can be seen from thecorresponding diagrams. With optimal temperature and filtration conditions a pressure peak of +10% is permissible for amaximum time of 0.5 sec.

Mounting and drive connections: consider the following indications when preparing the installation drawings for thesystem:• the pump is designed to operate with keyed shaft coupled axially and by means of a flexible coupling to the drive;• the clearance between the keyed shaft and the corresponding sleeve coupling has to be between 0.004 and 0.030 mm;• avoid axial and radial loads on the shaft;• the mounting flange has to be perpendicular to the drive shaft, with a maximum error of 0.18 mm every 100 mm;• when mounting onto a gearbox, or other component without a flexible coupling, it is advisable to order pumps with splined

shaft. In this case the clearance between splines has to be between 0.013 and 0.051 mm on the pitch diameter.

Hydraulic circuit: always install a pressure relief valve on the supply line to prevent the pressure from exceeding theallowed maximum. Normally, it is set in accordance with the weakest component in the system. (In the case where it isthe pump, set the valve to a pressure 15% higher than the maximum pressure rating of the pump.)Inlet line tubing should have a section equal to or greater than that of the inlet port of the pump. It is advisable to keepthe tube connecting the pump to the reservoir as short possible. Particular care has to be taken with the inlet line whichhas to be hermetically sealed to avoid entraining air into the circuit; this varies the characteristics of the hydraulic fluidcausing the operating parts to become damaged.

Filtration: the inlet line filter must have a flow rate capacity that is higher than that of the pump at its maximum operatingspeed. The filtration requirements for individual models are given in this catalogue. The use of a filter by-pass is recommendedfor cold starts and should the filter become clogged. Proper maintenance of the filter element is essential for the correctoperation of the entire system. In normal conditions replace the filter element after the first 50 hours of operation.Subsequently, replace it at least every 500 hours. Regarding the filter on the return line, the same general conditions applyas for the inlet line and it should be positioned in an accessible location for ease of maintenance.

Tank: if possible, the reservoir should be positioned above the pump. Otherwise, ensure that the minimum level of thefluid contained in it is higher than the pump inlet line opening. It is important to avoid draining the inlet line with the pumpat standstill. The opening of the return line into the reservoir must remain below the minimum level of the fluid in thereservoir. It must not be positioned too close to the opening of the inlet line to avoid the possibility of any air bubblespassing into the inlet line. Baffles inside the reservoir may be useful in avoiding the problem. Rapid temperature changescan cause condensation on the underside of the lid of the reservoir with the formation of droplets of water that can fallinto the oil. To avoid this problem it is recommended that the lid should have small vents so that the air space in thereservoir is ventilated. The vents have to be screened, though, to prevent the entry of dust or the sudden expulsion offluid.

Start-up: use the following procedure when the pump is started-up for the first time:completely fill the pump and the inlet line with fluid;start the engine for approximately one second a number of times at regular intervals of approximately 2 or 3 seconds untilthe noise level reduces, thereby confirming that it has been primed;with a manometer check to ensure that the outlet pressure increases slightly;once the pump has been primed, maintain low pressure levels activating all parts of the circuit a number of times untilair bubbles disappear completely from the return line to the reservoir.This procedure should be carefully as any residual air inside the pump can quickly cause the rotor to seize.

Cold starting: when starting the pump, especially with low ambient temperatures, operate with moderate speed andpressure until the average temperature in the entire circuit is within the given limits.

The information provided in this catalogue is subject to change without notice

Operating instructions

BV

28 Trowers Way Holmethorpe industrial estateredhill Surrey rH1 2LW. United Kingdom of Great Britain

telephone: +44(0)1737 767493 fax: +44(0)1737 772041 email: info@jbj.co.uk website: www.jbj.co.uk