7/24/2019 BZ-8002953

1/15

European Standard EN ISO 13000-1 : 1997 has the status of a DIN Standard.

A comma is used as the decimal marker.

National foreword

This standard has been published in accordance with a decision taken by CEN/TC 249 to adopt, withoutalteration, International Standard ISO 13000-1 as a European Standard.

The responsible German body involved in its preparation was the Normenausschu Kunststoffe(PlasticsStandards Committee), Technical Committee Sonstige Thermoplast-Formmassen.

The DIN Standards corresponding to the International Standards referred to in clause 2 of the EN are asfollows:

ISO Standard DIN Standard

ISO 1043-1 DIN 7728-1

ISO 12086-1 DIN 16782-1

ISO 12086-2 DIN 16782-2

ISO 13000-2 DIN EN ISO 13000-2

National Annex NA

Standards referred to(and not included in Normative references)

DIN 7728-1 Plastics Symbols for polymers and their special characteristics

DIN 16782-1 Polytetrafluoroethylene (PTFE) moulding materials Classification and designation

DIN 16782-2 Polytetrafluoroethylene (PTFE) moulding materials Preparation of specimens anddetermination of properties

DIN EN ISO 13000-2 Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 2: Prepara-tion of test specimens and determination of properties (ISO 13002 : 1997)

ICS 83.140.01

Descriptors: Plastics, polytetrafluoroethylene, requirements.

Kunststoffe Polytetrafluorethylen (PTFE)-Halbzeuge Teil 1: Anforderungen und Bezeichnung(ISO 13000-1 : 1997)

Ref. No. DIN EN ISO 13000-1 : 1998-05English price group 07 Sales No. 1107

10.98

DEUTSCHE NORM May 1998

EN ISO 13000-1

{

EN comprises 13 pages.

No part of this standard may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin.Beuth Verlag GmbH, D-10772 Berlin, has the exclusive right of sale for German Standards (DIN-Normen).

Polytetrafluoroethylene (PTFE) semi-finished productsPart 1: Requirements and designation

(ISO 13000-1 : 1997)

English version of DIN EN ISO 13000-1

7/24/2019 BZ-8002953

2/15

7/24/2019 BZ-8002953

3/15

English version

ICS 83.140.10

Descriptors: Plastics, polytetrafluoroethylene, requirements.

Central Secretariat: rue de Stassart 36, B-1050 Brussels

European Committee for Standardization

Comit Europen de Normalisation

Europisches Komitee fr Normung

Plastics

Polytetrafluoroethylene (PTFE) semi-finishedproducts

Part 1: Requirements and designation(ISO 13000-1 : 1997)

1997. CEN All rights of exploitation in any form and by any meansreserved worldwide for CEN national members.

Ref. No. EN ISO 13000-1 : 1997 E

Plastiques Semi-produits enpolyttrafluorothylne (PTFE) Partie 1: Spcifications et dsigna-tion (ISO 13000-1 : 1997)

Kunststoffe Polytetrafluorethylen(PTFE)-Halbzeuge Teil 1: Anforde-rungen und Bezeichnung(ISO 13000-1 : 1997)

This European Standard was approved by CEN on 1997-11-30.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations

which stipulate the conditions for giving this European Standard the status of anational standard without any alteration.

Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to anyCEN member.

The European Standards exist in three official versions (English, French, German).A version in any other language made by translation under the responsibil ity of aCEN member into its own language and notified to the Central Secretariat has thesame status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, the CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland,and the United Kingdom.

December 1997

EN ISO 13000-1

7/24/2019 BZ-8002953

4/15

Page 2EN ISO 13000-1 : 1997

Foreword

International Standard

ISO 13000-1 : 1997 Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 1: Requirementsand designation,

which was prepared by ISO/TC 61 Plastics of the International Organization for Standardization, has beenadopted by Technical Committee CEN/TC 249 Plastics, the Secretariat of which is held by IBN, as a EuropeanStandard.

This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, and conflicting national standards withdrawn, by June 1998 at the latest.

In accordance with the CEN/CENELEC Internal Regulations, the national standards organizations of the follow-ing countries are bound to implement this European Standard:

Austria, Belg ium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom.

Endorsement notice

The text of the International Standard ISO 13000-1 : 1997 was approved by CEN as a European Standardwithout any modification.

7/24/2019 BZ-8002953

5/15

Page 3EN ISO 13000-1 : 1997

4

4

5

5

5

5

6

6

6

6

7

7

7

8

8

8

8

9

9

9

9

10

10

10

11

11

12

13

7/24/2019 BZ-8002953

6/15

Page 4EN ISO 13000-1 : 1997

7/24/2019 BZ-8002953

7/15

Page 5EN ISO 13000-1 : 1997

7/24/2019 BZ-8002953

8/15

Page 6EN ISO 13000-1 : 1997

7/24/2019 BZ-8002953

9/15

Page 7EN ISO 13000-1 : 1997

7/24/2019 BZ-8002953

10/15

Page 8EN ISO 13000-1 : 1997

7/24/2019 BZ-8002953

11/15

Page 9EN ISO 13000-1 : 1997

7/24/2019 BZ-8002953

12/15

Page 10EN ISO 13000-1 : 1997

7/24/2019 BZ-8002953

13/15

Page 11EN ISO 13000-1 : 1997

7/24/2019 BZ-8002953

14/15

Page 12EN ISO 13000-1 : 1997

7/24/2019 BZ-8002953

15/15

Page 13EN ISO 13000-1 : 1997