64
— ‘/fr 1 C w - ui 1 1000 / (I +
— ‘/fr
1C
w-
ui
1 1000
/
(I
+
SYMBOL INSTRUCTIONS
___ ________
Raise needle Raise presser foot Lower presser foot
This houshold sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594
IMPORTANT SAFETY INSTRUCTIONSWhen using an electrical appliance, basic safety precautions should always be followed, including the following:
Read all instructions before using this household sewing machine.
DANGER - To reduce the risk of electric shock:• A sewing machine should never be left unattended when plugged in. Always unplug this sewing machine
from the electric outlet immediately after using and before cleaning.
• Always unplug before relamping. Replace bulb with same type rated 5 Watt.
WARNING - To reduce the risk of burns, fire,electric shock, or injury to persons:• Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or
near children or infirm person.
• Use this sewing machine only for its intended use as described in this manual. Use only attachmentsrecommended by the manufacturer as contained in this manual.
• Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it hasbeen dropped or damaged, or dropped into water. Return the sewing machine to the nearest authoriseddealer or service center for examination, repair, electrical or mechanical adjustment.
• Never operate the sewing machine with any air openings blocked. Keep ventilation openings of thesewing machine and foot control free from the accumulation of lint, dust, and loose cloth.
• Keep fingers away from all moving parts. Special care is required around the sewing machine needle.
• Always use the proper needle plate. The wrong plate can cause the needle to break.
• Do not use bent needles.
• Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
• Switch the sewing machine off (“0”) when making any adjustment in the needle area, such as threadingneedle, changing needle, threading bobbin, or changing presser foot, etc.
• Always unplug the sewing machine from the electrical outlet when removing covers, lubricating, or whenmaking any other user servicing adjustments mentioned in the instruction manual.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are being used or where oxygen is being administrated.
• To disconnect, turn all controls to the off (0”) position, then remove plug from outlet.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
SAVE THESE INSTRUCTIONS
CONTENTS
_________
PRINCIPAL PARTS OF THE MACHINE 6BUTTONS OF THE MACHINE 7LCD SCREEN 9PATTERN CHART 10ACCESSORIES 11CONNECTING THE MACHINE TO THE POWER SOURCE 12START SEWING 13Speed adjustment lever 13Foot control 13REPLACING THE NEEDLE 14CHANGING THE PRESSER FOOT 14ADJUSTING PRESSER FOOT PRESSURE 15MATCHING NEEDLE/ FABRIC! THREAD 15TYPE OF PRESSER FOOT CHART 16WINDING THE BOBBIN 17INSERTING THE BOBBIN 19THREADING THE UPPER THREAD 20USING THE NEEDLE THREADER 22TOP THREAD TENSION 23BRINGING UP THE BOBBIN THREAD 24CUTTING THE THREAD 24PRESSER FOOT LIFT 25RAISE OR LOWER THE FEED DOGS 25OPERATION BUTTONS 26Reverse button 26Auto-lock button 27Needle up/down button 27FUNCTION BUTTONS 28Stitch width button 28Stitch length button 29MODE selection button 29Pattern mirroring button 30MEMORY BUTTONS 31Memory button 31Clear button 31Arrow button 31SELECTION BUTTONS 32Direct pattern selection buttons 32Number buttons 32USEFUL SKILLS 33Sewing corners 33Reverse 33Free arm 33Sewing on heavy fabric 34STRAIGHT STITCHES AND NEEDLE POSITION 35
4
Changing the needle position.35
Changing the stitch length 35
ZIGZAG STITCHES 35
Adjusting the stitch length 35
Adjusting the stitch width 35
STRETCH STITCHES 36
OVERCASTING STITCHES 37
Using the overcasting foot 37
Using the standard foot 37
BLINDHEM 38
BUTTON SEWING 39
BUTTONHOLE STITCHING 40
Making a buttonhole on stretch fabrics 43
BAR TACK STITCH 44
EYELET STITCH 45
DARNING STITCH 46
ZIPPER INSERTION 48
QUILTING 49
SCALLOP EDGES 49
FREE-MOTION, DARNING, EMBROIDERY AND MONOGRAMMING 50
Darning 50
Embroidery 51
Monogramming 51
MIRRORING 52
MEMORY 53
Program patterns or letters 53
Add patterns or letters 54
Clear patterns or letters 54
Recall and sew the memorized pattern 55
WARNING FUNCTIONS 56
Warning animation message display 56
Instruction animation message display 56
Warning beeping sound 56
REPLACING THE LIGHT BULB 57
MAINTENANCE 58
Cleaning the screen 58
Cleaning the sewing machine surface 58
Cleaning the hook 58
TROUBLESHOOTING GUIDE 60
QUICK REFERENCE CHART 62
5
PRINCIPAL PARTS OF THE MACHINE
Tension dialPattern plate
Bobbin winder
LCD screen
1 Function buttons
3 Memory buttons
Selection buttons
0 Function buttons
Speedadjustment lever
Horizontal spool pin
Hole for secondspool pin
Handwheel
Main power switch
Presser foot pressure
Face plate
Operation buttons 0
Thread cutter
Buttonhole lever
Needle plate
Accessory tray
Power cord
Foot control connector
Handle
Presser foot lift
Feed dog adjustmentlever
6
BUTTONS OF THE MACHINE
0 0
1. Reverse button
Hold down this button to sew either backwards or a reinforcement stitch at a low speed.
0
a
2. Auto-lock button
Hold down this button to sew locking stitches immediately or at the end of the current pattern
and automatically stop.
3. Needle upldown button
Press this button to move the needle either up or down.
B. Function buttons
4. Stitch length
Press this button to adjust the length of the stitch.
A. Operation buttons
7
5. Stitch width
Press this button to adjust the width of the stitch.
6. Pattern mirroring
Press this button to sew a mirrored pattern.
7. Mode selection
Press this button to select direct mode, utility and decorative pattern mode or block lettermode.
C. Memory buttons
8. Clear button
If an incorrect pattern is selected or programmed, pressing this button will clear it.
9. Arrow button
Press the “GD” button or” G’” button until the desired stitch number in the programmedcombination is displayed.
10. Memory button
Press this button to enter or store the programmed pattern combination in the memory.
D. Selection buttons
11. Direct pattern selection and number buttons
Instant access to direct pattern or press the pattern number to select the desired pattern.
8
LCD SCREEN
Direct Pattern
Auto-lockNeedle up Mirror
- ----- Buttonhole lever
Bobbinwinding
Reverse --
Pattern number
Pattern
Direct mode
Needle position
Stitch width
Needle down Mirror
Auto-stop
Suggested presser foot -
Needle up
- Stitch widthCurrent position in theprogrammed memoryTotal space in the memoryMemory
Auto-stop --- -
Pattern number
Suggested presser foot
Alphabet mode
Stitch widthCurrent position in the
____________
programmed memoryTotal space in the memoryMemoryStitch length
1 Bi
__/jT]j2jO3
I.iir.I
I 32 IIR1OWJi1II_
_______
Reverse
Pattern number
Normal mode
Alphabet
Stitch length
ow-F!! HiRlLZc11
__
9
C)
?C
O>
k
s---
g0
t\)
•:l2
S:.
---
M
—O
C.4
)Jz
-.
I:f
:i°V
V.
g;
-i-i
0)
0)
‘vM
-4::
C)
8><
XX
£\7
VO
8(
.:;1
.CD
‘g
CD°.:.
C4E1
I1Th
Q
CDC.
)-r
—-
-
-
0
-s-I
z -
1JUU’
Vv
MT
2. —r’.
)fj
0C
DJ
CD CD 3C.
)C.
)
C.)
C.)
0)
C.)
0)
ACCESSORIES
1 Standard foot (T)
2. Zipperfoot(l)
3. Buttonhole foot (D)
4. Overcasting foot (E)
5. Blindhem foot (F)
6. Satin stitch foot (A)
7. Button sewIng foot
8. 1/4’ Quilting foot (P)
9. Free-motion/darning foot
10. Pack of needles
11. Spool pin felt
12. Second spool pin
13. Brush/ Seam ripper
14. Spool cap (Large)
15. Spool cap (Small)
16. Seam guide
17. Bobbin
18. Screwdriver (L & 5)
19. Hard cover
13 14
L
18
1 2 3 4
10 11
__I®
/15 16 17
aD 1 0000
V0000
I c300
}
11
CONNECTING THE MACHINE TO THE POWER SOURCE
Caution: Always make sure that the machine is unplugged from power source and theirwin witt h is on when the machine is not in use and before inserting or removing
wrts
Connecting the machine
Before connecting the power supply, make sure that the voltage and frequency shown on themachine is conforming with your electrical power.
Place the machine on a stable table.
1. Connect the power line cord to the machine by inserting the 2-hole plug into the terminalbox.
2. Connect the power line plug to the electric outlet.
3. Turn on the power switch.
4. The light bulb will light up when the switch is turned on.
To disconnect, turn the power switch to the off position, then remove plug from outlet.
OFF ON
For the USA and Canada
This appliance has a polarized plug (one blade wider than the other),to reduce the risk of electrical shock; this plug will fit in a polarizedoutlet only one way. If the plug does not fit fully in the outlet, reversethe plug. If it still does not fit, contact a qualified electrician. Do notmodify the plug in any way.
12
START SEWING
Speed adjustment lever
The speed adjustment lever can controlthe sewing speed. To increase the speed,slide the lever to right. To decrease thesewing speed, slide the lever to the left.
With the sewing machine turned off, insertthe foot control plug into its connector onthe sewing machine.
Turn on the sewing machine, and thenslowly depress the foot control to startsewing.
Release the foot control to stop thesewing machine.
Please Note: The setting of the speed control slide will limit the maximum speed of themachine.
Foot control
Attention: Consult a qualified electrician if in doubt as how to connect the machine to thepower source. Unplug the power cord when the machine is not in use.
The appliance must be used with the foot controller C9OOO.
13
I iREPLACING THE NEEDLE
___
Attention: Turn power switch to off (“0’) whencarrying out any of the operations below.
Change the needle regularly, especially if it isshowing signs of wear and causing problems.
Insert the needle following the illustratedinstructions.
A. Loosen the needle clamp screw and tightenagain after inserting the new needle.
The flat side of the shaft should be towards theback.
B. Insert the needle as far up as it will go.
Needles must be in perfect condition. Problemscan occur with;
- Bent needles
- Blunt needles
Damaged points
Attention: Turn power switch to off(0”) when carrying out any of theoperations below.
Attaching the presser foot holder (1)
Raise the presser foot bar (a). Attach thepresser foot holder (b) as illustrated.
Attaching the presser foot (2)
Lower the presser foot holder (b) until thecut-out (c) is directly above the pin on thefoot (d).
Raise the lever (e).
Lower the presser foot holder (b) and thepresser foot (f) will engage automatically.
Removing the presser foot (3)
Raise the presser foot.
Raise the lever (e) and the foot willdisengage.
Attaching the seam guide (4)
Attach the seam guide (g) in the slot asillustrated. Adjust according to need forhems, pleats, quilting, etc.
CHANGING THE PRESSER FOOT
14
ADJUSTING PRESSER FOOT PRESSURE
Needle, fabric, thread selection guide
The presser foot pressure of the machinehas been pre-set and requires noadjustments for most fabric weights.
However, if you choose to adjust thepresser foot pressure, turn the presseradjusting screw with a coin.
For sewing very heavy fabric, loosen thepressure by turning the screw counterclockwise, and for thin fabric, tighten byturning it clockwise.
NEEDLE SIZE FABRICS THREAD
9-11 (70-80) Lightweight fabrics-thin Light-duty thread in cotton,cottons, voile, silk, muslin, nylon, polyester or cottoninterlocks, cotton knits, tricot, wrapped polyester.jerseys. crepes, wovenpolyester, shirt & blousefabrics.
11-14(80-90) Medium weight fabrics-cotton, Most threads sold are mediumsatin, sailcloth, double knits, size and suitable for theselightweight wool. fabrics and needle sizes. Use
14 (90) Medium weight fabrics-cotton polyester threads on synthetic
duck, wool, heavier knits, materials and cotton on natural
terrycloth, denims. woven fabrics for best results.. . Always use the same thread
16 (100) Heavyweight fabrics-canvas,on top and bottom
wool, outdoor tent and quiltedfabrics, denims, upholsterymaterial (light to medium).
18 (110) Heavy wool, overcoat fabrics, Heavy duty thread, carpetupholstery fabrics, some thread.leathers and vinyls.
Please Note:
- In general, fine threads and needles are used for sewing fine fabrics, and thickerthreads are used for sewing heavy fabrics.
- Always test thread and needle size on a small piece of fabric which will be used foractual sewing.
- Use the same thread for needle and bobbin.
MATCHING NEEDLE! FABRIC! THREAD
15
TYPE OF PRESSER FOOT CHART
PRESSER FOOT APPLICATION PRESSER FOOT APPLICATION
Standard foot (T) General sewing,Patchwork stitches, Satin stitch foot (A) Satin stitch
) Decorative stitching.Smocking,
0 Fagoting, etc.
Inserting zippersQuilting
-
0 TZipper foot (I) 1/4’S Quilting foot (P)
Buttonhole sewing Free-motion/Darning!Embroidery!Monogramming
!jJVpn
u U U II U ! Free-motion/darning foot
Buttonhole foot (D)
OvercastingButton sewing foot Button sewing
0
Overcasting foot (E)
Blind hem stitching
NBlindhem foot (F) I
0
16
WINDING THE BOBBIN TJ
Bobbin winding
4
H
1. Place the thread and spool cap onto the spool pin.For smaller spools of thread, place spool cap with thesmall side next to the spool or use the small spool cap.
2. Snap the thread into the thread guide.
3. Wind the thread clockwise around the bobbin windertension discs.
4. Place the thread end through one of the inner holes inthe bobbin as illustrated and place empty bobbin onthe spindle.
5. Hold on to the thread tail and push the bobbin to right.
17
;\\
6. When the bobbin winder spindle is pushed to the right,“bobbin winding position”, the symbol “D”is shownon the LCD screen.
It will disappear from the LCD screen when the bobbinwinder spindle is push to the left, “sewing position”.
7. Hold the thread tail securely in one hand.
8. Press on the foot control to start the sewing machine.
9. After the bobbin has wound a few turns stop themachine and cut the thread near the hole of thebobbin. Continue filling the bobbin until it is full. Themotor stops automatically when the bobbin is full. Stopthe machine. Push the bobbin winder spindle to left.
10. Cut the thread and then remove the bobbin.
Please Note: When the bobbin winder switch is pushed to the right, ‘bobbin windingposition”, the machine will not sew and the handwheel will not turn, To start sewing, pushthe bobbin winder switch to the left “sewing position”.
6
8
18
INSERTING THE BOBBIN
Attention: Turn power switch to off (0”)before inserting or removing the bobbin.
When inserting or removing the bobbin,the needle must be fully raised.
1. Remove bobbin cover. Insert the bobbinin the bobbin case with the thread runningin a counterclockwise direction (arrow).
2. Pull the thread through the slit (A).
3. Pull the thread toward the left and alongthe inside of the spring until it slips intothe notch (B) being sure that the threaddoes not slip out of the slit (A).
4. Pull out about 15 cm (6 inches) of threadand slide on the bobbin cover (C).
19
THREADING THE UPPER THREAD
Please Note: It is important to thread correctly to prevent sewing problems.
Start by raising the needle to its highest point by turning
the hand wheel toward you. Raise the presser foot lift to
open the tension discs.
1. Lift up the spool pin. Place the spool of thread on thespool pin so that the thread comes from the front of the
spool, then place the spool cap at the end of the spoolpin.
2. Pull the thread from the spool through the upper threadguide.
3. Guide the thread around the thread guide pulling thethread through the pre-tension spring as illustrated.
20
21L
4. Thread the tension discs by pulling the thread downbetween the silver discs.
5. Then, down and around the check spring holder andback up to the take up lever.
6. Pull the thread from right to the left through the slottedeye of the take-up lever and then down again.
7. Pass the thread behind the flat, horizontal threadguide.
8. Guide the thread into the wire loop.
9. Thread the end of the thread through the needle fromfront to back, and pull out about 10cm of thread. Oruse the needle threader to thread the needle. (On thenext page).
4
(4.6
21
USING THE NEEDLE THREADER
Attention: Turn power switch to the offposition (‘0’).
Raise the needle to its highest positionand lower the presser foot.
1. Lower the needle threader lever slowlyand draw the thread through the threadguide as illustrated and then to the right.
2. The needle threader automatically turnsto the threading position and the tiny hookpasses through the needle eye.
3. Take the thread in front of the needle intothe hook from the bottom as illustrated.
4. Hold the thread loosely and release thelever slowly. The hook will turn and pullthe thread through the needle eye forminga loop.
Pull the thread through the needle eye.
22
TOP THREAD TENSION
___ ____
Tight
_________________
Loose
- Basic top thread tension setting: “4”
- To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dialto the next number down.
- Proper setting of tension is important to good sewing.
- There is no single tension setting appropriate for all the stitch functions and fabrics.
- 90% of all sewing will be between “3” and “5” (“4” is basic setting).
- For all decorative sewing you will always obtain a nicer stitch and less fabric puckering whentop tension is reduced by 1 number so the upper thread appears on the bottom side of yourfabric.
1. Normal thread tension for straight stitchsewing. Top and bobbin thread lock in thefabric.
2. Thread tension is too loose for straightstitch sewing. Turn dial to higher number.Top thread loops on wrong side.
3. Thread tension is too tight for straight stitchsewing. Turn dial to lower number. Bobbinthread loops on top side.
4. Normal thread tension for zigzag anddecorative sewing.
Wrongside
Top side
Upper threadBobbin thread
Wrongside
Upper thread :JJ:!j—1s—1.r1J:::2 Bobbin thread
Top side
Top side
Wrongside
Upper threadBobbin thread
side
Wrongside
Upper threadBobbin thread
23
BRINGING UP THE BOBBIN THREAD
1 Hold the upper thread with the lefthand. Turn the handwheel towardyou (counterclockwise) lowering, thenraising the needle.
2. Gently pull on the upper thread tobring the bobbin thread up through theneedle plate hole. The bobbin threadwill come up in a loop.
3. Pull both threads to the back under thepresser foot.
Raise the presser foot. Remove the fabric,draw the threads to the left side of the facecover and cut using the thread cutter.
The threads are cut at the proper length tostart the next seam.
CUTTING THE THREAD
24
PRESSER FOOT LIFT
RAISE OR LOWER THE FEED DOGS
1 The presser foot lift raises and lowersyour presser foot.
2. When sewing several layers or thickfabrics, the presser foot can be raisedhigher for easy placing of the fabricunder the foot.
With the accessory tray off the machine,the feed dog adjustment lever can beseen on the base in back of the sewingmachine.
Sliding the lever to the “-vv-” (b) will lowerthe feed dog, for example during buttonsewing. If you wish to continue sewingnormally, slide the lever to the “AA” (a) inorder to raise the feed dogs.
The feed dog will not come up until youturn the handwheel or start sewing, evenif the lever is to the right. Make a completeturn to raise the feed dogs.
25
OPERATION BUTTONS
Needle up/downbutton
Auto-lock button
Reverse button
Reverse button
FiT ftJj3When the patterns 01-16, 32-60 are selected, themachine will sew reverse or a reinforcement stitch
at a low speed if the reverse button is pressed.The machine will sew forward after the button isreleased.
An arrow “on the LCD display indicatesreverse sewing.
26
Auto-lock button
Needle upldown position button
1 1 I
When the patterns 01-05 are selected, themachine will immediately sew 3 locking stitcheswhen the Auto-lock button is pressed, thenautomatically stop. The LCD will display the figure
until the machine is stopped.
When the patterns 06-16, 32-60 are selected,press the Auto-lock button, the machine will sew3 locking stitches at the end of the current patternand automatically stop. The LCD will display thefigure “0” until the machine is stopped.
The function will be cancelled if you press thebutton once again or select another pattern.
With the Needle up! down button, you decidewhether the needle shall stop in the up position orin the fabric when you stop sewing.
Please Note: If you press the button whilesewing nothing will happen. The functioncan only be used when the machine is notsewing.
Press the button so that the arrow, on the LCDscreen, will point up L” and the needle will stopin the highest position. When you press the buttonso that the arrow points down “Is”, the machinewill stop with the needle in the lowest position.
roli
___
J
aIrT1jjEL frbi J
27
FUNCTION BUTTONS fl7H’
Stitch width button
Stitch length button
Mirroring button
Mode selection button
When you select a stitch, the machine willautomatically set the recommended stitch width,which will be indicated by numbers on the LCDscreen. The stitch width can be changed bypressing the stitch width adjustment buttons.
For a narrower stitch, press the “-“ button (left).For a wider stitch, press the “+“ button (right). Thestitch width can be adjusted between “0.0-7.0”.Some stitches have a limited stitch width.
When patterns 01-05 are selected, the needleposition is changed by the stitch width adjustmentbuttons. Pressing the “-“ button (left), will movethe needle to the left and pressing the “+“ button(right), will move the needle to the right. Thenumbers will be changed from left position ‘00”to extreme right position “7.0’. The pre-set centerneedle position will be indicated as “3.5”.
Stitch width button
__
rn ICE r T lli E[Sfli
II:9I
CIiWT1O2.Sij31
28
Stitch length button
MODE selection button
When you select a stitch the machine willautomatically set the recommended stitch lengthwhich will be indicated by numbers on the LCDscreen. The stitch length can be adjusted bypressing the stitch length adjustment buttons.
To shorten the stitch length, press the “-“ button(left). For a longer stitch length, press the “+“
button (right). The stitch length can be adjustedbetween “0.0-4,5”. Some stitches have a limitedlength.
When you turn the machine “ON” the LCD screendisplay will be set to direct mode“ “.
Press the ““ button to switch to patterns mode,“ “. If you press the function button again, thealphabet mode will be displayed “I’’
After a third press the machine will go back todirect mode“
Direct mode stitch selection.
Utility and decorative pattern mode:
Stitch selection using number buttons.
1 Block letter mode:
Character selection using number buttons.
__
w ‘I
II /iTjs][3.s
—s---- —A---
MEMORY
TCi( 2 T)3D
TC4(
29
Pattern mirroring button
The patterns 01-16, 32-60 can be mirrored bypressing the “ED” button.
The LCD will display the mirroring function and themachine will continue to sew the mirrored patternuntil the mirroring function is cancelled by pressingthe mirror button again.
When the mirroring function disappears from theLCD screen, the machine will start sewing thenormal stitch.
If you change the pattern, the mirroring functionwill be cancelled accordingly. Press the mirrorbutton again if you want the new pattern to bemirrored.
32iBijj[iIirI
—---
MEMORY
tCi fl• 3III I0 J
TC4( )6)
30
MEMORY BUTTONS
Clear button
Arrow button
Memory button
Press the “® button to enter the memorymode and program combinations of characters ordecorative stitches. Press the “CE)” button againto leave the memory mode and return to directmode.
Please Note: The Direct mode patterns andbuttonholes cannot be programmed or putinto memory.
Clear button
Press this button when the incorrect character isselected. Each press of this button erases onecharacter, or press this button to remove an addedpattern when sewing combinations of characters or
______________________________________
decorative stitches.
Arrow button
Press the arrow buttons “G” or “ED”, in
memory mode, to check the combinationprogrammed in the memory.
Memory button
__
rn317
L
31
SELECTION BUTTONS
Direct pattern selectionand number buttons
Direct pattern selection buttons
When the mode button is set to Direct mode youcan select the utility stitches illustrated next to thebuttons simply by pressing the button for the stitchyou wish to sew.
Number buttons
When the mode button is set to Patterns orAlphabet mode you select the stitches or letters bynumber.
r
__
F
___
I.S11TI
r rn
TCi_(®)D
Ci
ED
32
USEFUL SKILLS
Sewing corners1. Stop the sewing machine
when you reach a corner.
2. Lower the needle into thefabric with the hand wheel or
by pressing the needle up/down button once.
3. Raise the presser foot.
4. Use the needle as a pivotand turn the fabric.
5. Lower the presser foot andresume sewing.
Reverse stitching is usedto secure the threads at thebeginning and at the end of aseam.
Press the reverse button andsew 4-5 stitches.
The machine will sew forwardwhen the button is released.
Reverse
Free arm
Free arm sewing is convenient for sewing tubular areas such as pant hems and cuffs.
33
Sewing on heavy fabric
The black button on the rightside of the presser foot will lockthe presser foot in a horizontalposition if you push it in beforelowering the presser foot. Thisensures even feeding at thebeginning of a seam and helpswhen sewing multiple layersof fabric such as sewing overseams when hemming jeans.
When you reach the point of anincreased thickness, lower theneedle and raise the presserfoot. Press the toe of the footand push in the black button,then lower the foot and continuesewing.
The black button releasesautomatically after sewing fewstitches.
You also can place anotherpiece of fabric with the samethickness at the back of theseam. Or support the presserfoot while feeding by hand andsewing toward the folded side.
34
STRAIGHT STITCHES AND NEEDLE POSITION
01 02 03 04 05
rTT! 4I I I I II I I I II I I II I I I I
c0.0 2.0 3.5 5.0 7.0
I II I II I
0.5 1 .0 2.0 3.0 4.5
IChanging the needle position
These setting apply only to patterns 01-05. The pre-setposition is “3.5”, center position. When you press thestitch width adjustment button, the needle position willmove to the left. When you press the “+“ stitch widthadjustment button, the needle position will move to theright. On the LCD screen, the point illustration and thenumber indicate the needle position.
Changing the stitch length
To shorten the stitch length, press the “-“ stitch lengthadjustment button. For a longer stitch length, press the“+“ stitch length adjustment button.
Generally speaking, the thicker the fabric, thread andneedle, the longer the stitch should be.
ZIGZAG STITCHES
J010iJ1I!
Adjusting the stitch widthThe maximum zigzag stitch width for zigzag stitchingis “7.0”; however, the width can be reduced on anypatterns. The width increases as you press the “+“ stitchwidth adjustment button from “0.0-7.0”,
Adjusting the stitch length
The density of zigzag stitches increase as the setting ofstitch length approaches “0.2”.
Most zigzag stitches are sewn at “1.0-2.5”.
Dense zigzag stitches (close together) are referred to asa satin stitch.
35
STRETCH STITCHES
Stretch stitches are strong and flexible andwill give with the fabric without breaking.Good for easy to ravel and knit fabrics, aswell as joining durable fabric such as denims.
These stitches can also be used as adecorative top stitch.
The straight stretch stitch is used to add triplereinforcement to stretch and stressed seams.
The triple zigzag stretch stitch is suitable forfirm fabrics like denim, poplin, duck, etc.
03 04 08cD D
I
03 04
InInInIn
IIIIIIfluIllIIIIIIIIIIllIllIIIIIIIIIIIIIIIIII
36
Aftention: The overcasting foot should be used to sew with patterns 06 and 09 only. Do notset the stitch width narrower than “5.0”. It is possible for the needle to hit the presser footand break when sewing other patterns and width.
Change the presser foot to the standard foot (T)
Sewing the overcasting along the edge of the fabric so that the needle drops over the edge ofthe fabric on the right side.
OVERCASTING STITCHES
Using the overcasting foot
06 09
5.0-7.0 2.0-3.0
<<<<<<
KKKKKKfr
1. Change the presser foot to the overcasting foot (E).
2. Sew the fabric with the fabric edge against the guide of the overcasting foot.
Using the standard foot
2.54.5 2.0—3.0
< k
kkkk
1.
2.
37
BLINDHEM
Please Note: It takes practice to sewblindhems. Always make a sewing test
Snap on foot F.
1 Fold the fabric as illustrated with thewrong side uppermost.
2. Place the fabric under the foot. Turn thehandwheel forwards by hand until theneedle swings fully to the left. It shouldjust pierce the fold of the fabric, If it doesnot, adjust the stitch width accordingly.
3. Adjust the guide on the foot (b) by turningthe knob (a) so that the guide just restsagainst the fold.
4. Sew slowly, guiding the fabric carefullyalong the edge of the guide.
25-4.O
11: Blindhem for woven fabrics
1 O212: Blindhem for stretch fabrics
5mm 5mm
tniReverse Overcastingside stitches
first.
Reverseside
5. Turn fabric to right side.
38
BUTTON SEWING
____
29
2.54.5
1. Select the pattern 29 to get the buttonsewing stitch. Change the presser foot to
_________ _________
the button sewing foot.
2. Position the fabric under the foot. Placethe button in the desired position, lowerthe foot on to the button.
3. Adjust the stitch width to “2.545”according to the distance between the twoholes of the button.
4. Turn the handwheel to check that theneedle goes cleanly into the left and rightholes of the button.
5. Before sewing, press the Autolockbutton to sew reinforcement stitchesautomatically at the beginning and at theend of the stitch.
If a shank is required, place a darningneedle on top of the button and sew.
6. For buttons with 4 holes, sew the two frontholes first, pull fabric forward and thensew the two back holes.
II 29] I[f 1 u:z uE:1
6
39
BUTTONHOLE STITCHING
17: For thin or medium fabric
18: For horizontal holes on blouses orshirts made from thin or mediumfabric
19: For thin or medium fabric
20: For horizontal holes on blouses orshirts made from thin or mediumfabric
21: For horizontal buttonholes on thickO3-1O fabrics
22: For thin or medium fabric
23: For suits or overcoats
O.31.O 24: For thick coats
25: For jeans or trousers
26: For jeans or stretch fabric with acoarse weave
27: For stretch fabric
your project, practice on a scrap piece of the
1. Mark the positions of the buttonhole on thefabric.
The maximum automatic buttonhole lengthis 3cm (1 3/16 inch). (Total of diameter +
thickness of button.)
2. Attach the buttonhole foot. then pull outthe button holder plate and insert thebutton. The size of the buttonhole isdetermined by the button inserted in thebutton plate.
The thread should be passed through thehole in the presser foot, then be placedunder the foot.
2.5-7O 0.3—tO
3.O-.7.O 0.3—tO
2.5-5.5h Puud
23 24 25
Ii26
U 30-70 10-20
27a 3.0-7.0 1.0-3.0
Please Note: Before sewing a buttonhole onsame type of fabric.
1
2
40
3. Select the buttonhole stitch. Adjust thestitch width and the stitch length to thedesired width and density.
4. Position the fabric under the presser footso that the buttonhole mark is aligned withthe center of the buttonhole foot.
Pull down the buttonhole lever, then pushit to the back.
Please Note: When you select anybuttonhole pattern the LCD screen willdisplay the figure “9” to remind youto lower the buttonhole lever.
5. Start sewing while lightly holding the endof the upper thread.
Please Note: The machine willautomatically sew a reinforcement stitchafter the buttonhole is sewn.
F
__
1rniNii rFi I
I!, I
L
41
6. Buttonholes are sewn from the front of thepresser foot to the back, as shown.
7. Raise the presser foot and cut thread.To sew over same buttonhole, raisethe presser foot (will return to originalposition).
After sewing the buttonhole stitch, pushthe buttonhole lever up until it stops.
8. Cut the center of the buttonhole beingcareful not to cut any stitches on eitherside. Use a pin as a stopper at the bartackso you do not cut too much.
17 18
r, [19 20 21 22 I’ ‘LI23 24 25
Duo
0tii
26 27
till
U6
L
42
Making a corded buftonhole on stretch fabrics
Attach the buttonhole foot and hook thegimp thread onto the back of the presserfoot. Bring the two gimp thread ends to thefront of the foot and insert them into thegrooves, then temporarily tie them there.Lower the presser foot and start sewing.
Set the stitch width to match the diameterof the gimp thread.
2. Once sewing is completed, pull the gimpthread gently to remove any slack, thentrim off any excess.
Please Note: It is suggested that you use interfacing on the wrong side of the fabric.
43
BAR TACK STITCH
1% 10-30 03-10
Select pattern 30 to get the bartack stitch.Change the presser foot to the buttonholefoot.
2. Pull the button holder to the rear. Set thebutton guide plate on the buttonhole footto the desired length.
3. Pass the upper thread down through thehole in the presser foot. Position the fabricso that the needle is 2mm (1/16 inch)in front of the pocket opening, and thenlower the presser foot lever.
4. Pull down the buttonhole lever then pushit back. The buttonhole lever is positionedbehind the bracket on the buttonhole foot.Gently hold the end of the upper thread inyour left hand, and then start sewing.
5. Bartack stitches are sewn as illustrated.
6. As an example, the procedure for sewingbar tacks at pocket corners.
16
a5
44
EYELET STITCH
5.0 6.0 7.0
Select stitch 28 for sewing eyelets on belts, etc
1
A B C
s,
2
(
3
1. Select pattern 28 to get the eyelet stitch.Attach satin stitch foot (A).
2. Press the or “+“ stitch width adjustmentto select the eyelet size.
Size of eyelet:
A. Large: 7.0mm (1/4 inch).
B. Medium: 6.0mm (15/64 inch).
C. Small: 5.0mm (3/16 inch).
3. Lower the needle into the fabric at thebeginning of the stitching, and then lowerthe presser foot lever.
Once sewing is completed, the machineautomatically sews reinforcement stitches,then stops.
4. Make a hole at the center using an eyeletpunch.
Eyelet punch is not included with themachine.
Please Note: If thin thread is used, thestitching may not be dense enough. Ifthis occurs, sew the eyelet twice oneon top of the other.
____
IIii I flilB iLR
Ii;iji
45
DARNING STITCH
1
3.5-7.0 1.0-2.0
1 Baste the upper fabric and the underfabric together.
Select pattern 31 to get the darning stitch.Change the presser foot to the buttonhole
foot.
2. Lower the presser foot over the center ofthe tear.
3. Pull the button holder to rear. Set thebutton guide plate on buttonhole foot tothe desired length of the darning stitch.
4. The size of one darning stitch is variable.However, the maximum stitch length is2.6cm (1 inch) and the maximum stitchwidth is 7mm (9/32 inch).
a. The length of sewing.
b. The width of sewing.
____
IIi z’ Frn1NiiWiII!, J I
L
—1Stop/
I AAAAAAIIllIllIllIllhllIllIllIllIllIltllIIfllllhlIfl
a illiiIillllIftI IIlIllIllIflhlIllIhhhlllhIhhlllIhhhhhhlflfllfliI,,yYv,,
StarH
4
46
5. Position the fabric so that the needle is2mm (1/16 inch) in front of the area tobe darned. Pass the upper thread downthrough the hole in the presser foot andthen lower the presser foot lever.
Please Note: When lowering thepresser foot, do not push in the front ofthe presser foot, otherwise the darningwill not be sewn with the correct size.
6. Pull down the buttonhole lever then pushit back. The buttonhole lever is positionedbehind the bracket on the buttonhole foot.Gently hold the end of the upper thread inyour left hand, and then start sewing.
Please Note: When you select anybuttonhole pattern or darning pattern.the LCD screen will display the figure
to remind you to pull down thebuttonhole lever.
7. Darning stitches are sewn from the front ofthe presser foot to the back, as shown.
8. If the area to be darned is too big to sewwith one darning stitch, you can sewseveral times (or cross sew) to get bettersewing result.
it
7
______ _____
47
ZIPPER INSERTION
3.5 1.5-3.0
Attention: Zipper foot should be usedfor sewing width center needle positionstraight stitch only. It is possible thatneedle could hit the presser foot andbreak when sewing other patterns.
1. Baste the zipper opening on the garment.
2. Press open the seam allowance. Place thezipper face down on the seam allowancewith the teeth against the seam line. Bastethe zipper tape.
3. Attach the zipper foot. Attach the right sideof the presser foot pin to the holder whensewing the left side of the zipper.
4. Attach the left side of the presser foot pinto the presser foot holder when sewing theright side of the zipper.
5. Stitch left side of the zipper from bottom totop.
6. Stitch across the lower end and right sideof zipper. Remove the basting and press.
Inserting a centered zipper
_5 —
48
QUILT! N G
3.5 1.0-3.0
Insert the quilting guide in the presser footholder as illustrated and set the space as youdesire.
Sew the first row and move over the fabricto sew parallel rows of channel quilting withthe guide riding along the previous row ofstitching.
Please Note: For better results, applyspray starch onto the fabric and presswith a hot iron before it is sewn.
Stitch along the edge of the fabric,marking sure not to sew directly on theedge of the fabric.
2. Trim along the stitches.* Be careful not to cut the stitches.
0301
InInInIn
SCALLOP EDGES
49
FREE-MOTION, DARNING, EMBROIDERY AND MONOGRAMMING
Move the feed dog adjustment lever to “w”to lower the feed dogs.
Remove the presser foot holder, and attachthe free-motion/darning foot to the presserfoot holder bar. The lever (a) should bebehind the needle clamp screw (b). Press thefree-motion/darning foot on firmly from behindwith your index finger and tighten the screw(c).
Please Note: Free-motion darning is accomplished without the sewing machine internalfeed system. Movement of the fabric is controlled by the operator. It is necessary tocoordinate sewing speed and movement of fabric.
First sew around the edges of the hole (tosecure the threads). Working from left toright, sew over the hole in a constant andcontinuous movement. Turn the work by 1/4and sew over the first stitching moving thework slower over the hole to separate thethreads and not form big gaps between thethreads.
3.5-5.0
Darning
50
Select zigzag stitch pattern and adjust thestitch width as desired.
Stitch along the outline of the design bymoving the embroidery hoop. Make sure tomaintain a constant speed.
Fill in the design working from the outlinetowards the inside. Keep the stitches closetogether.
You will get longer stitches by moving thehoop faster and shorter stitches by movingthe hoop more slowly.
Secure with a reinforcement stitches at theend by press Auto-lock button.
Select the zigzag stitch pattern and adjustthe stitch width as desired. Sew at a constantspeed, moving the hoop slowly along thelettering.
When the letter is finished. Secure with areinforcement stitches at the end by pressingthe Auto-lock button.
Embroidery
Monogrammi ng
/
Embroidery hoop is not included with the machine.
51
MIRRORING
z Please Note:
- Pattern 17-31 cannot be mirrored.
- Mirrored patterns can also be combined with other patterns.
1. Select the pattern.
ii 31 i Fa R NJJI OZThJ
________________________________J
12. Pressing the mirroring button. LCD will display
the mirroring function and the machine will
j i sew the mirrored pattern until you press the
_________
trU I I • J.J i.j mirroring button again.
IIF1
MEMORY
TCi_(r®T)_3)
\T(Ø) 6D /\ C1Ei®O
2\
A. Normal pattern sewing.
AB. Mirror pattern sewing.
B%%
j3
52
MEMORY
____ ___ ___ ___ ___
Combined patterns can be stored for later use. Since stored patterns are not lost after thesewing machine is turned off, they can be recalled at any time. This is convenient for patterns,such as names, that will be used often.
Please Note:
- The machine has a program memory that can retain 30 units of stitches.
- Multiple patterns selecting from pattern modes “l ,“ can be combined andsewn together.
- All the units in the memory can be edited to set its function such as Stitch length, Stitchwidth, Mirroring and Auto-lock.
- The Direct mode patterns and buttonholes can not be programmed.
Program patterns
L
1
2
L1Li ijlFi
ExE®
1. When you turn the machine “ON”, the LCD screendisplays ““.
2. Press the ‘ ‘ button to enter the memory modeand program combinations of letters or decorativestitches.
3. Press the “Gd” button to select any desiredpattern among ““ or”“ on the LCDscreen. Then press the desired pattern number(E.g.13). (You can change the stitch length, width,or choose the Auto-stop, mirroring function ifdesired.>
Repeat step 3 for more patterns to be stored in thememory.
Please Note: When the maximum of 30 unitsof patterns has been programmed, the machinewill beep to signal the memory is full.
[13 i[flNll
—— MEMORY
3
53
r i[1OQ]i
4
1LI] UJJJ oz:. Ui
5 EXEX
4. Use the arrow E)” or” CD” button to switchbetween the stitches in the combination and checkwhat you have programmed.
5. Press the “E” button to leave the memory modeand return to the Direct mode.
Attention: The selected pattern will be cleared from the memory module after closingthe machine if you do not press the . . button again when you have completed yourprogramming.
Add patterns or letters
Clear patterns or letters
While in the memory mode, press the “CD” buttonor the “E” button until the stitch number you haveselected is displayed, then add the new stitch orchange the stitch length and width, or add Auto-stop ormirroring, if desired.
If you wish to delete a certain stitch within in thememory mode, use the “ED” button or CD” buttonuntil the actual stitch number is displayed.Press the “ED” button to delete the selected patternand following patterns will move one step back.
Ri llIJ
I____I[3LL
54
Recall and sew the memorized pattern
2. Press foot control. The machine will start to sewfrom first entered pattern. On the LCD screen,sewing stitch data is indicated.
3. If you wish to check what is programmed or if youwish to start sewing a few stitches in the memorymode, use the “CD” button or “ CD” button.
You can use the Auto-lock “D” function when thesewing machine is stopped.
4. Press the “®“ button to leave the memory modeand return to the Direct mode.
1. Press the “®“ button to enter the memorymode. The machine will be positioned at thefirst programmed stitch.
I‘3 T1N2.sj
...
1
I_____l3iidTj2.Sjjj.
7
2
3D
3
Please Note: If you wish to repeat your stitch combination without having the machine
stop press the Auto-lock ‘ button to cancel the Auto-Stop in the memory mode. The Dwill disappear from the LCD screen.
Ifl1JTll.sjU3.sl
4
55
WARNING FUNCTIONS
Warning animation message display
Buttonhole lever is not lowered
The buttonhole or darning stitch was selected andthe foot control pressed while the buttonhole leveris raised.
Instruction animation message display
z Bobbin winding
The bobbin winder is engaged.
Warning beeping sound
- When operating correctly: 1 beep
- When the memory is full 30 units of pattern: 2-short beeps
- When operating incorrectly: 3-short beeps
- When the sewing machine is thread locked and can’t sew: 8 seconds short beepsIt means that the thread is twisted or caught and the hand wheel can’t move. Pleaselook through the Troubleshooting guide to find the solution. After the problem has beensolved, the machine will continue to sew.
Push bobbin winder stop to sewingposition
If you have not pushed back the bobbin tothe left when the bobbin is full and press anybutton or try to sew, the machine will give awarning sound of 3 beeps.
Please Note: If the problem is still not solved, please contact your local dealer.
Attention: During the sewing, if the thread is caught or wrapped inside the hookstopping the needle from moving and you continue pressing the foot control, thesecurity switch will stop the machine completely. In order to restart the sewing machine,clean out the thread that is caught then turn OFF (he on/off switch and then ON again.
I7ijfJII:F1 J
LcgJ F lIIiI’’
56
REPLACING THE LIGHT BULB
A Attention: Turn the power switch off and wait until the light bulb has cooled down before
touching it.
1 Remove plug (a), loosen the screw (b) onthe left side of the sewing machine andremove the face plate (c).
2. Replace the bulb as follows:
Pull light bulb downward to remove.
Replace the bulb with same type rated12V/5W.
Replace the face plate and tighten thescrew.
57
MAINTENANCE
Attention: Disconnect the power cord from the wall socket before cleaning the screenand sewing machine surface, otherwise injury or electrical shock may result.
Cleaning the screen
If the front panel is dirty, wipe it gently with asoft, dry cloth.
Do not use any organic solvents or detergents.
If the surface of the sewing machine is dirty, lightly soak a cloth in mild detergent, squeeze it outfirmly and then wipe the surface. After cleaning it once in this way, wipe the surface again with adry cloth.
Cleaning the hook
If lint and bits of thread accumulate in the hook, this will interfere with the smooth operation of themachine. Check regularly and clean the stitching mechanism when necessary.
Attention: Disconnect the machine from the wall outletbefore carrying out any maintenance.
1. Remove the bobbin cover plate andbobbin.
2. Clean the bobbin holder with a brush.
Cleaning the sewing machine surface
58
(11
CD
C CD 0 0 D CD C,) CD 0) D ci
CD 3 0 CD
DD
”D
CDO
CD
—D
CDCD
<tD
—_,
CDD
OCD
0D
—CD
CD
DCD
2C
Dci
CD
.C
D
CD3C
D
0.
CD-
3CD
0O
U) CD
0.
CD
CD 0) C) CD 0) 0 CD 1ZD 0) Cl)
—-3
00)
S—
C)
CDcC
)C
DP
(0(1
)0)
CD
5.0
DØ
C)
•‘—
0))
COC
D H
0CD
0) D
CD
CD DC
0)*
C)>
CD
C,) OC
DC
DC
D
0)0.
DO C
0 C))
(DD c
rC
O
DD
Ca
TROUBLESHOOTING GUIDE
_____
Before calling for service, check the following items. If the problem still persists, contact the placeof purchase or your nearest authorized dealer.
Problem Cause Correction
Upper thread 1 .The machine is not threaded correctly. 1 Rethread the machine.breaks 2.The thread tension is too tight. 2.Reduce the thread tension (lower number).
3.The thread is too thick for the needle. 3.Select a larger needle.
4.The needle is not inserted correctly. 4.Remove and reinsert the needle (flat side towards theback).
5.The thread is wound around the spool 5.Remove the spool and wind thread onto spool,holder pin.
6.The needle is damaged. 6.Replace the needle.
Lower thread 1 .The bobbin case is not inserted correctly. 1 .Remove and reinsert the bobbin case and pull on thebreaks thread, The thread should pull easily.
2.The bobbin case is threaded wrong. 2.Check both bobbin and bobbin case.
3.The lower thread tension is too tight 3.Loosen lower thread tension.
Skipped 1.The needle is not inserted correctly. 1.Remove and reinsert needle (flat side towards thestitches back).
2.The needle is damaged. 2.lnsert a new needle.
3.The wrong size needle has been used. 3.Choose a needle to suit the thread.
4.The foot is not attached correctly. 4.Check and attach correctly.
5.The machine is not threaded correctly. 5.Rethread the machine.
6.The presser foot pressure is not correct. 6.lncrease the presser foot pressure.
Needle 1 The needle is damaged. 1 Insert a new needle.breaks 2.The needle is not correctly inserted. 2.lnsert the needle correctly (flat side towards the back).
3.Wrong needle size for the fabric. 3.Choose a needle to suit the thread and fabric.
4.The wrong foot is attached. 4.Select the correct foot.
5.The needle clamp screw is loose. 5.Use the screwdriver to firmly tighten the screw.
6.The presser foot that is used is not 6.Attach the presser foot that is appropriate for the typeappropriate for the type of stitch that you wish of stitch that you wish to sew.to sew.
7.The upper thread tension is too tight. 7.Loosen the upper thread tension.
Loose 1 .The machine is not correctly threaded. 1 Check the threading.stitches 2.The bobbin case is not correctly threaded. 2.Thread the bobbin case as illustrated.
3.Needle/fabric/thread combination is wrong. 3.The needle size must suit the fabric and thread.
4.Thread tension is wrong. 4.Correct the thread tension,
Seam gather 1 The needle is too thick for the fabric. 1 Select a finer needle.or pucker 2.The stitch length is adjusted wrong. 2.Shorten the stitch length.
3.The thread tension is too tight. 3.Loosen the thread tension.
60
Problem Cause Correction
Seam puckering 1 The needle thread tension is too tight. 1 Loosen the thread tension.
2.The needle thread is not threaded 2.Rethread the machine.
correctly.
3.The needle is too heavy for the fabric 3Choose a needle to suit the thread and
being sewn. fabric.
4.The stitch length is too long for the 4.Shorten stitch length.
fabric.
5.The presser foot pressure is not correctly 5.Adjust the presser foot pressure.
adjusted.
Patterns are distorted 1 .The correct presser foot is not used. 1 Select the correct foot.
2The needle thread tension is too tight. 2.Loosen the thread tension.
The machine jams I Thread is caught in the hook. Remove the upper thread and bobbin case,
2 The feed dogs are packed with lint, turn the handwheel backwards and forwardsby hand and remove the thread and lint.
The machine is noisy 1 Lint or oil have collected on the hook or 1 Clean the hook and feed dog as described.
needle bar.
2.Poor quality oil has been used, 2.Qnly use good quality sewing machine oil.
3.The needle is damaged. 3.Replace the needle.
4 Humming sound coming from internal 4Normal.
motor.
5.Thread is caught in the hook. Remove the upper thread and bobbin case.
6 The feed dogs are packed with lint,turn the handwheel backwards and forwardsby hand and remove the thread and mt.
Uneven stitches, uneven 1 Poor quality thread. 1 Select a better quality thread.
feed 2.The bobbin case is threaded wrong. 2.Remove the bobbin case, the thread andreinsert correctly.
3.Fabric has been pulled. 3.00 not pull on the fabric while sewing, let itbe fed up by the feed dogs.
The sewing machine does 1 .The machine is not turned on. 1 Turn on the machine.
not operate 2,The presser foot lever is raised. 2Lower the presser foot lever.
3.The machine is not plugged in. 3.Connect the power line plug to the electricoutlet.
61
QUICK REFERENCE CHART
Pattern Width (mm) Length (mm) Presser FunctionsAuto Manual Auto Manual Foot Reverse Auto-lock Mirror/presser foot Twin needle Memory
Utility 01 j———-- 3.5 0.0—7.0 2.5 0.0—4.5 T * * * * *
stitchesO2____ 0.0 0.0—7.0 2.5 0,0—4.5 7 * * * * *
033 3.5 0.0—7.0 5 1.0-3.0 T * * * *
043—..— 3.5 1.0—6.0 2.5 1.0—3.0 T * * * * *
050—w--w 3.5 00—7.0 2.5 1.5—3.0 T * * * *
06/*\J\/\ 5.0 0.0—7.0 2.0 0.3—4.5 T * * * * *
07/\**, 5.0 2.0—7.0 1.0 03—4.5 T * * * *
O8 5.0 2.5—7.0 2.5 1.0—3.0 7 * * * * *
091\1\ 5.0 3.5—7.0 2.5 1.0—3.0 E * */7*
io]_/ 5.0 2.5—7.0 2.5 1.0—3.0 7 * * * * *
Ii vv 3.5 2.5—7.0 2.0 0.5—4.5 F * * */T *
12V 3.5 2.5—7.0 1.0 0.5—4.5 F * * *fl * *
131111111 3.5 2.5—7.0 2.5 1.5—3.0 T * * * * *
i4J 0 2.5—7.0 2.5 1.0—3.0 7 * * * * *
i5 7.0 2.5—7.0 2.5 1.0—3.0 A * * * * *
16<<S<<< 5.0 2.5—7.0 2.5 1.0—3.0 A * * * * *
Button- i7II::::I 5.0 2.5—7.0 0.5 0.3—1.0 D
stesi8I::j 5.5 3.0—7.0 0.5 0.3—1.0 0
i9H) 5.0 2.5—5.5 0.5 0.3—1.0 0
2oII:::: 0 3.0—7.0 0.5 0.3—1.0 D21 5.0 2.5—5.5 0.5 03—1.0 0
22 C) 5.0 2.5—5.5 0.5 0.3—1.0 D
23II: 7.0 5.5-7.0 0.5 0.3-1.0 D
7.0 5.5—7.0 0.5 0.3—1.0 0
254 TO 5.5-7.0 0 0.3-1.0 0
26I 6.0 3.0—7.0 1.0 1.0—2.0 D271* ,.z 6.0 3.0—7.0 1.5 1.0—3.0 0
28 0 7.0 7.06.05.0 A29 Q 3.5 2.5—4.5
30 2.0 1.0—3.0 0.5 0.5—i .0 031 7.0 3.5—7.0 2.0 1.0—2.0 0
Satin 32AA 7.0 2.5—7.0 0.5 0.3—1.0 A * * * * *
stitches 33 7.0 2.5—7.0 0.5 0.3—1.0 A * * * * *
7.0 2.5—7.0 0.5 0.3—1.0 A * * * *
35 7.0 2.5—7.0 0.5 0.3—1.0 A * * * * *
361 7.0 2.5—7.0 0.5 0.3—1.0 A * * * * *
37d’, 7.0 2.5—7.0 0.5 0.3—1.0 A * * * * *
38 7.0 2.5—7.0 0.5 0.3—1 0 A * * * * *
Cross 39)000< 5.0 2.5—7.0 2.5 1.0—3.0 A * * * *
stitches4O)38O 6M 5.0—7.0 1.0 1.0—3.0 A * * * * *
* Adjustments can be made.
62
Pattern Width (mm) Length (mm) Presser FunctionsAuto Manual Auto Manual Foot Reverse Auto-lock Mirror/presser foot Twin needle Memory6.0 3.0—7.0 1.5 1.0—3.0 A * * * *
Deco- 42111 I II 5.0 2.5—7.0 2.5 1.5—3.0 A * * * * *
rative5.0 2.5—7.0 2.0 10—3.0 A * * * * *stitches — —
44 7.0 3.0—7.0 2.0 10—3.0 T * * * * *
45*E* 5.0 3.0—7.0 - 1,5—4.5 A * * * * *
46fVSyI 7.0 2.5—7.0 2.0 1.0—3.0 T * * * * *
47Il1 5.0 2.5—7.0 2.5 1.5—3.0 T * * * * *
48jftflJj 5.0 2.5—7.0 1.0 1.0—3.0 T * * * * *
49 6.0 3.5—7.0 1.5 1.5—3.0 A * * * * *
5oQ. 5.0 2.5—7.0 1.5 1.0—3.0 T * * * *
51 5.0 4.5—7.0 1.0 1.0—3.0 A * * * *
52x 7.0 6.0—7.0 3.0 2.0—3.0 A * * * * *
53 )-)-)- TO 5.0—7.0 2.0 2.0—3.0 A * * * *
7.0 3.0—7.0 2.0 1.5—3.0 A * * * * *
7.0 3.0—7.0 2.0 2.0—3.0 A * * * * *
56 7.0 4.0—7.0 3.0 2.5—4.5 A * * * *
57 s 7.0 4.0—7.0 3.0 2.0—3.0 T * * * * *
58 7.0 2.5—7.0 2.0 1.0—3.0 A * * * * *
59 4 . 5.0 2.5—7.0 2.0 1.0—3.0 A * * * *
60 ? ? O 4.0—7.0 2.0 1.5—3.0 A * * * *
* Adjustments can be made.
Please note that on disposal, this product must besafely recycled in accordance with relevant Nationallegislation relating to electrical/electronic products.If in doubt please contact your retailer for guidance.
63
