VACUUM CONVEYING
C Series Conveyor Troubleshooting Guide
www.piab.com
VACUUM CONVEYORS
2
INTRODUCTION
Thank you for your purchase of a
PIAB Vacuum Conveyor.
This manual provides you all the informationnecessary for the successful installation, op-eration and maintenance of your unit. Westrongly recommend that this manual becarefully studied prior to installation or opera-tion. Doing so will avoid the possibility of in-advertent damage or malfunction of theequipment. Following the recommendedmaintenance instructions will ensure betterperformance and extended equipment life.
Also included within this manual is a list ofrecommended spares. These items are sub-ject to wear during normal use. We recom-mend that they be purchased in advance andkept in stock to avoid possible down time andfuture delays.
Because PIAB equipment may be shipped aspart of an installation involving other types ofequipment, or dissimilar units are sometimesconnected to perform specific functions, youshould familiarize yourself with the manualscovering the other equipment before pro-ceeding with installation. By cross-referenc-ing the manuals, you may save valuable in-stallation time and avoid improper operation.
In the design and manufacture of this equip-ment, PIAB has exercised the utmost care toensure many years of trouble-free operation.In the event that parts or technical assistanceis required, please contact us at:
PIAB USA, Inc.
65 Sharp Street
Hingham, MA 02043
Ph: (800) 321-7422/ (781) 337-7309
Fax: (781) 337-6864
www.piab.com
It is the users' responsibility to operate thisequipment in a safe manner and ensure com-pliance with all applicable safety laws andcodes.
WARRANTY:
PIAB Vacuum Conveyors are thoroughly in-spected and tested before shipping. EachPIAB Vacuum Conveyor is warranted to befree of defects in workmanship and materialsfor five years from date of purchase (filter andwear parts excluded.)
VACUUM CONVEYORS
3
CONTENTS
Page
SAFETY INSTRUCTIONS 4
CONNECTION EXAMPLES 7
CU-1A/B Connection
CU-2A/B Connection
PPT/R Connection
VCC-EP Connection
ACHIEVING THE DESIRED RATE 16
Filter replacement
Cleaning and Maintaining the Pump
MLL200-1200 Components
MLL Panel Component
Inside Components of MLL Pumps
MLD100 Components
TROUBLESHOOTING GENERAL 24
TROUBLESHOOTING L SERIES PUMP 25
TROUBLESHOOTING CU-1A/B 33
PIAB Control Unit CU-1A/B & CU-2A/B
CU control function and pneumatic diagrams
/ Pipe emptying
TROUBLESHOOTING PPT/R 42
PIAB Control Unit PPT/R
PPT/R control function and pneumatic
diagram, connections
Disassembling a PPT/R control
TROUBLESHOOTING VCC-EP 48
PIAB Control Unit VCC-EP
Mounting and connections
Valve Connections for the VCC-EP
TROUBLESHOOTING WITH A LEVEL DETECTOR 51
PIAB Level Detector
TROUBLESHOOTING INJECTION VALVES 51
Pneumatic Injection Valve
CLEANING OUT A PACKED CONVEYOR 54
Air Shock Assembly
MAINTENANCE SCHEDULE 55
VACUUM CONVEYORS
4
SAFETY INSTRUCTION
Instructions for building into a system
PIAB vacuum conveyors are CE marked. The personwho installs the conveyor in another main system hasthe responsibility of carrying out a risk analysis whenthis is desired.
Dust explosions
When handling and conveying dry powders and mate-rial consisting of small particles, there is a risk that adust explosion may occur. A dust explosion may occurwhen certain finely divided materials are mixed with air(oxygen) and then are ignited by, for example, a spark.
In order to minimise the risk of dust explosions, all in-cluded parts of the conveying system must be connect-ed to one and the same point of earth (equipotential)according to applicable regulations. It is also importantnot to smoke, weld or carry out other work where therisk of generation of sparks may be present in the vi-cinity of the conveyor.
In the table below are some examples of materials thatmay cause dust explosions.
The conveyor may not be used in explosive surround-ings containing the following gases: acetylene, carbondisulphide, hydrogen, hydrogen sulphide and ethyleneoxide.
ATEX-Atmosphere Explosible and CE. PIAB vacuum conveyors are not EX classified.PIAB vacuum conveyors conforms to EU directive 94/9/EC.
Cleaning of filters
It is important to check and clean/change filters at reg-ular intervals so that they are not clogged, as thismight lead to the fact that the filters will be subjectedto overload, and that undesired matters or particlesleak from the conveyor.
Emergency stop
The system builder shall provide the machine with anemergency stop function. As an option to the vacuumconveyor there is a remote control box with a built-inemergency stop function.
Start/stop of the conveyor
The conveyor is started either with the provided controlunit or via another main control system. The conveyorstops if the supply of compressed air is suddenly inter-rupted. The conveyor must be re-started by the opera-tor even if the supply of compressed air is reactivated.
Vacuum power at the inlet
Careless usage and incorrect installation of the feed-ing point of the vacuum system may cause injuries.The vacuum level is concentrated at the feeding pointand may cause injuries to eyes and mucous mem-branes.
u Never aim a suction tube, a feed nozzle or a hose at anyone.
u The larger the suction inlet, the higher the power and danger.
u The installation must be made so that the inlet cannot contact the operator and other people.
u Always remember to disconnect the supply of compressed air when cleaning or servicing the vacuum conveyor.
u
Aluminium Carbon
Aspirin Magnesium
Cotton Flour
Iron Nylon
Cacao Sugar
Coffee Corn
Cork Wood
+O2 +=
VACUUM CONVEYORS
5
Exhaust from the vacuum pump
The exhaust air from the conveyor’s vacuum pumpmay, in certain applications, constitute a risk andcause injuries. If the filter is not fully intact when pow-der with small particles is conveyed, the particles maypenetrate the filter and enter the pump, and further onout to the atmosphere and possibly contaminate it.Dangerous gases may also be generated and be car-ried out together with the exhaust air. In such casesthe pump shall be fitted with a central exhaust with anexternal filter. In certain cases, another alternativecould be the use of a sterile-filter unit. Never look di-rectly into the outlet of the vacuum pump. Do not for-get to disconnect the supply of compressed air whencleaning or servicing the vacuum conveyor
Compressed air
We recommend that compressed air of at least qualityclass 3 is used (ISO norm 8573.1) for PIAB’s vacuumpumps. This means that only a maximum of 5 mg/m3
of a maximum of 5 µ size particles may be present inthe compressed air.
For the USDA conveyor to conform to the American re-quirements of the authorities, the air for the air shockmust be delivered according to 3-A Accepted PracticeNo. 604-04. This means, among other things, that theair shall be free from oil and be filtered.
Preventing pressure-drops in the air supply
It is important to correctly dimension the compressed-air hose that supplies the conveyor so that unneces-sary pressure drops do not occur. The longer the hose,the larger the dimension required. Also rememberthat push-in connections with built-in non-return valvesmay cause pressure drops. Also, take into consider-ation that there may be other devices in the com-pressed-air network that might consume compressedair.
Dimensioning of the compressed-air pipeline
A very important part of a vacuum system is correctlydimensioned hoses and connections. In order to getthe highest possible performance from each vacuumpump, the table below that recommends hose diame-ters in mm (inner diameter) should be used.
The above compressed-air connections apply for pipe-lines that are shorter than 10 m (33 ft). If the pipelineis longer than 10 m (33 ft), select a pipeline of a largerdiameter.
Installation of compressed air
The feed pressure of the compressed air is between0.4 (58) and 0.6 (87 psi) MPa for PIAB vacuum convey-ors and pumps. Careless usage of compressed air maycause injuries.
The compressed air may not be used for any other pur-pose than specified.
All applicable safety regulations for installation, opera-tion and maintenance must be followed.
Always disconnect the supply of compressed air whencleaning or servicing the vacuum conveyor.
You are responsible for your own and other people’ssafety at the place of work.
Contact your local PIAB distributor if you have anyquestions.
Pump model Compressed-air connection
Exhaust connec-tion (mm)
Maxi L100 1/2" 75
Maxi L200 1/2" 75
Maxi L400 1/2" 75
Maxi L600 1" 2x75
Maxi L800 1" 2x75
Maxi L1200 1" 2x75
Maxi L1600 1" 2x75
VACUUM CONVEYORS
6
Disconnecting the compressed-air pipeline
Before the compressed-air pipe of the pump is discon-nected the pressure to the compressor must be turnedoff. After that, the pipeline may be disconnected.
Dismounting the conveyor
It important that the conveyor is emptied of its powderbefore dismounting is started. The compressed-airsupply must be disconnected before dismounting theconveyor.
Mounting of the conveyor
The conveyor is delivered mounted. When mounting itafter cleaning/servicing, it is important that seals andfilters are mounted correctly so that leakage does notoccur. C21 and C33 shall be anchored at one point atleast (either at the bottom valve unit or at the connec-tion girdle). C56 shall be anchored at two points atleast (at the bottom valve unit and at the upper or low-er connection bracket).
Hot surfaces
There is a risk that the external air shock becomes hot(60° C, 140° F) during and after use.
Position of the operator
The operator shall be at a position where he can easilystart and stop the conveyor.
Remote control of the conveyor
When using remote control, the system builder shouldensure that the conveyor can not be simultaneouslyoperated from two locations.
Installation of the conveying pipeline
Correct dimensioning and installation is A and O for thesystem to work in the best possible way.
Please contact your local PIAB distributor as to dimen-sioning of the diameters of the pipes, their length,number of bends and possible option of injection unitsor pipe emptying function. It is important that the pipe-line system is sealed in order to prevent the conveyedpowder from leaking from the equipment to causedamage to other devices and injuries. It is also impor-tant to make sure that no foreign matters can inadvert-ently be sucked into the conveyor.
Some basic tips
u The conveying pipeline should be installed without
having any unnecessary bends.
u Avoid inclined rises in the conveying pipeline.
u The radius of the pipeline should be at least 10
times the pipe diameter.
u Choose pipes instead of hoses where possible.
u Avoid all types of edges and restrictions at pipe
joints and connections.
Noise level
The measured noise levels (72–76 dBa) have beenmeasured in the following manner. The distance be-tween the pump and sound level meter = 1 metre. Thehigher measuring value applies to the exhaust air-flowin the direction of the sound level meter and the lowermeasuring value applies to the exhaust air flowingfrom the sound level meter. Please notice that thenoise level of the conveying depends on the kind ofpowder that is conveyed.
VACUUM CONVEYORS
7
CONNECTION EXAMPLESCONTROL UNIT CU-1A/B ART. NO. 01 04 550
ART. NO. 01 04 552
VACUUM CONVEYORS
8
CONTROL UNIT CU-1A/B WITH FLUIDISATION ART. NO. 01 04 550ART. NO. 01 04 552
VACUUM CONVEYORS
9
CONTROL UNIT CU-1A/B WITH FLUIDISATION AND LEVEL DETECTOR ART. NO. 01 04 550ART. NO. 01 04 552
VACUUM CONVEYORS
10
CONTROL UNIT CU-1A/B USDA ART. NO. 01 04 550ART. NO. 01 04 552
VACUUM CONVEYORS
11
CONTROL UNIT CU-2A/B ART. NO. 01 04 540ART. NO. 01 04 548
VACUUM CONVEYORS
12
CONTROL UNIT CU-2A/B WITH FLUIDISATION AND LEVEL DETECTOR ART. NO. 01 04 540ART. NO. 01 04 548
VACUUM CONVEYORS
13
CONTROL UNIT CU-2A/B WITH FLUIDISATION ART. NO. 01 04 540ART. NO. 01 04 548
VACUUM CONVEYORS
14
CONNECTION EXAMPLES
VACUUM CONVEYORS
15
VALVE UNIT VCC-EP
VALVE UNIT VCC-EP WITH FLUIDISATION
VACUUM CONVEYORS
16
ACHIEVING THE DESIRED RATE
Is the air pressure at least 87 psi entering into the pump, in the proper line size, and with enough volume?
A. If the conveyor is functioning fine but the rate needs to be changed, try adjusting the timers. Since each ma-terial conveys in a different manner, there are not particular on and off times that will achieve certain rates. Ifthe material has all been dumped out and the bottom door remains open, the off time can be shortened. Tryminor adjustments, increasing the on time and decreasing the off time. The off time may need to be increasedas the on time is increased to avoid packing the material in the conveyor.
Note: The conveyor has a maximum internal volume, please consult the user manual for your specific conveyor.
B. If the product tends to move in slugs (big clumps of material that fill the line) or dense phase, increased aspi-ration may be necessary. The easiest way to add more air is at the feed point.
1. Feed Wand - The standard feed wands include two places to adjust the aspiration. The black piece atthe top of the wand twists around the wand, covering or uncovering openings in the actual wand. The morethe openings are uncovered, the more air that is allowed to enter the system. In order to rotate the blackpiece; unscrew the bottom wing nut. Retighten when the desired amount of opening is uncovered.
a.The inside tube can be adjusted up or down. If the tube is all the way down, touching the cage, therewill be less aspiration and a greater amount of product picked up. If the tube is pulled out to be evenwith the outer tube, there will be increased aspiration and a decreased amount of product picked up.The tube can be adjusted by unscrewing the top wing nut.
2. Feed Adapter - The standard feed adapters include two ball valves. Both are adjustable which allow in-creased aspiration.
a. If the material is not flowing easily into the cone on the feed adapter, the ball valve closest to thecone should be opened up until the product freely flows. This ball valve is attached to a pipe that shouldbe extended all the way out, approximately 8.5". If the material will not even flow into the cone, sometype of aspiration or agitator may need to be added before the feed adapter. The second ball valveshould be opened more if the material is conveying in dense phase.
b. If the material is very free flowing, it may drop from the cone into the perpendicular tube and clogthe tube. If this is the case, push the ball valve attached to the inner tube in closer to the cone.
3. Injection Valve - An injection valve can be added into a system no matter which feed method is beingused. There are two types of injection valves. The first type of injection valve has a ball valve that can beopened for increased aspiration. The second type of injection valve senses a high vacuum and allows as-piration as needed
Conveyor Min. Compressed Air Line
Max. Required Volume (scfm)
C21 100 classic .25 "14.8
C21100 .5 "14.8
C series 200 .5 "29.7
C series 400 .5 "59.0
C series 600 1.0 "89.0
C series 800 1.0 "118.6
C series 1200 1.0 "178.0
C series 1600 1.0 "237.3
VACUUM CONVEYORS
17
C. If there is little to no transport of material with a low vacuum, but the conveyor is still cycling properly.
1.The seals in between the modules may be cracked and leaking.
2.There may be a loose connection somewhere with the hose.
3.There may be too much aspiration.
a. If a sensing injection valve is being used, make sure the feed pressure is between 58-87 psi. If thefeed pressure is over 87 psi, the injection valve will remain open all of the time.
4.The seals inside of the pump may be cracked or worn. Refer to page 27.
5.Does the bottom flap close? - If not please turn to the section with the proper controller.
D. If there is little to no transport of material with a high vacuum, but the conveyor is still cycling properly.
1.The filter may be clogged.
2.Aspiration may need to be added.
3.There could be a clog in the pipeline.
4.The pump may be filled with material.
E. If there is material packed into the conveyor, and it is not dumping out properly.
1.The on time may need to be decreased.
2.The off time may need to be increased.
3.The material may be too damp.
a.The product may be sticky.
b.The compressed air may be damp, adding air to the material being conveyed.
4. Fluidization may need to be added to the conveyor. If it is already part of the conveyor, it may not be
functioning properly. The material would be stuck in the cone section located at the bottom of the convey-or.
5.The filter air shock may not be working properly.
F. If the filter air shock does not function properly, there wouldn't be a 'bump' to shake the excess material off ofthe filter. This can be heard when the bottom flap door opens.
1.Check the connections, both compressed air and from the air shock to the pump.
2.Make sure there is not a kink in the tubing to the air shock.
3.If the tubing has material in it, the tubing must be cleaned out or replaced.
4.The valve on the filter shock should push in and out easily. If not, clean it off and add a little lubrication.
5.If the air shock still won't function properly, the air shock valve may be defective.
G. If there is material coming out of the exhaust of the pump, there is a filter problem.
1.The filter may be worn and need to be replaced.
2.The filter may have been put on wrong. Please refer to diagram on page 18, 19.
3. In either case, the side plate should be removed to look inside of the pump. For optimum performancethere should not be any material in the pump, especially the nozzles. Please refer to page 23 for directionson maintaining and cleaning the pump.
VACUUM CONVEYORS
18
FILTER REPALCEMENT1
2 3
4 5
VACUUM CONVEYORS
19
6 7 8
9 10
11 12
VACUUM CONVEYORS
20
FILTER CLEANING
7
It may be necessary to clean the filter elements under certain circumstances, e.g. after a change of product. In this case, you are welcome to draw on our experience! We shall be glad to help you choose the best cleaning method.
PITEX CLEANING
HERDING SINTERED BRUSH OFF CLEANING
cleaning procedure:1. Your filter elements have to be dismantled in order to be cleaned. 2. Place soiled filter element into washing machine at or below 40ºC (104ºF), with mild detergent. Or you may handwash your filters. 3. Do not machine dry your PITEX filters. 4. Place filters on wire shelf. Allow filter to air dry completely before re-installation. 3. Reinstall the ddry PITEX filter elements in the filter unit.
Brush-off cleaning procedure:1. Your filter elements have to be dismantled in order to be cleaned. 2. Stand the filter elements in a vertical a position as possible (e.g. lean them against a wall, see the drawing). 3. No dust should be allowed to get into the filter elements during the cleaning operation. It is recommended, therefore, to cover up the inside of the filter (e.g. with adhesive tape). 4. Brush off the dust with a soft brush -Bristle length: 75mm (3”) -Bristle diameter: 0.7mm (0.025”) -Bristle material: Nylon or PVC Brush off the dust from top to bottom a maximum of 2 times, applying just a little pressure -Contact pressure: 5N (1.1 pound force) 5. Turn the filter elements and proceed in like manner for the rear and the narrow sides. 6. Clean the head and foot zone last, taking care not to allow any dust to get into the filter elements. 7. Reinstall the filter elements in the filter unit.
VACUUM CONVEYORS
21
HERDING SINTERED RINSE OFF CLEANING
HERDING SINTERED AIR JET CLEANING
Rinse-off cleaning procedure:1. Your filter elements have to be dismantled in order to be cleaned. 2. Stand the filter elements in a vertical a position as possible (e.g. lean them against a wall, see the drawing). 3. No dust should be allowed to get into the filter elements during the cleaning operation. It is recommended, therefore, to cover up the inside of the filter (e.g. with adhesive tape). 4. Rinse off the dust with gentle water pressure -Maximum pressure of thewater jet upon impact: 1 bar (14.5 psi) -Maximum water temperature: 40°C (104F) 5. Turn the filter elements and proceed in like manner for the rear and the narrow sides. 6. Clean the head and foot zone last, taking care not to allow any water to get into the filter elements. 7. Leave the filter elements standing at the same acute angle to dry. Drying must take place at room temperature (minimum 24 hours). 8. Reinstall the ddry filter elements in the filter unit.
Air-jet cleaning procedure:1. Your filter elements have to be dismantled in order to be cleaned. 2. Stand the filter elements in a vertical a position as possible (e.g. lean them against a wall, see drawing above). 3. No dust should be allowed to get into the filter elements during the cleaning operation. It is recommended, therefore, to cover up the inside of the filter (e.g. with adhesive tape). 4. Clean off the dust with a gentle air jet -Maximum pressure of the air jet upon impact: 1 bar (14.5 psi) 5. Turn the filter elements and proceed in like manner for the rear and the narrow sides. 6. Clean the head and foot zone last, taking care not to allow any dust to get into the filter elements.8. Reinstall the filter elements in the filter unit.
VACUUM CONVEYORS
22
GORE SINBRAN BRUSH OFF CLEANING
GORE SINBRAN RINSE OFF CLEANING
Brush-off cleaning procedure:1. Your filter elements have to be dismantled in order to be cleaned. 2. Stand the filter elements in a vertical a position as possible (e.g. lean them against a wall, see the drawing). 3. No dust should be allowed to get into the filter elements during the cleaning operation. It is recommended, therefore, to cover up the inside of the filter (e.g. with adhesive tape). 4. Brush off the dust with a soft brush
-Bristle length: 75mm (3”) -Bristle diameter: 0.7mm (0.025”) -Bristle material: Nylon or PVC
Brush off the dust from top to bottom a maximum of 2 times, applying just a little pressure
-Contact pressure: 5N (1.1 pound force) 5. Turn the filter elements and proceed in like manner for the rear and the narrow sides. 6. Clean the head and foot zone last, taking care not to allow any dust to get into the filter elements. 7. Reinstall the filter elements in the filter unit.
Rinse-off cleaning procedure:1. Your filter elements have to be dismantled in order to be cleaned. 2. Stand the filter elements in a vertical a position as possible (e.g. lean them against a wall, see the drawing). 3. No dust should be allowed to get into the filter elements during the cleaning operation. It is recommended, therefore, to cover up the inside of the filter (e.g. with adhesive tape). 4. Rinse off the dust with a gentle water jet -Maximum pressure of the water jet upon impact: 1 bar (14.5 psi) -Maximum water temperature: 120°C (248F) 5. Turn the filter elements and proceed in like manner for the rear and the narrow sides. 6. Clean the head and foot zone last, taking care not to allow any water to get into the filter elements. 7. Leave the filter elements standing at the same acute angle to dry. Drying must take place at room temperature (minimum 24 hours). 8. Reinstall the ddry filter elements in the filter unit.
VACUUM CONVEYORS
23
CLEANING AND MAINTAINING THE VACUUM PUMP
PIAB vacuum pumps are easy to clean and maintain. The only wear parts in the pumps are flap valvesand gaskets. A slow, gradual loss in vacuum could be attributed to cracked gaskets or flap valves.Please refer to pages 26 for a spare parts breakdown. The spare kits include all of the necessary flapvalves, gaskets, and a compressed air filter.
A slow gradual loss in vacuum could also be attributed to product moving through the pump. If anymaterial has come out of the exhaust, chances are the pump needs to be cleaned out.
Classic and L 100 vacuum pumps
The pump should be opened up and examined. Please refer to page 31 for a diagram and parts break-down of the Classic 100. First the panel plate should be removed, and then the side plate. The valveplate and side plate gasket is now visible. Located underneath the valve plate are the flap valves. Arethe gaskets or flap valves cracked? If so, the repair kit 32.01.069 should be purchased. The vacuumchambers and nozzles should now be visible. Is the material that is being conveyed in the chambers ornozzles? For optimum performance, there should not be any material in the pump. The pump's perfor-mance decreases as more material gets lodged in the nozzles. Please be careful when cleaning thepump. If a nozzle is broken off or rotated, the pump will need to be replaced. To remove material fromthe nozzles or chambers, PIAB suggests soaking the pump in water or in water with mild detergent suchas dishwashing detergent. Once the pump has new seals and flap valves and it is clean and put backtogether, it should run just like a brand new pump.
L100, L200, L400, L600, L800, L1200, L1600 vacuum pumps
The pump should be opened up and examined. Please refer to page 26-30 for a diagram and partsbreakdown of the vacuum pump. First the left side plate and gasket should be removed. This should ex-pose the vacuum chambers and nozzles. If the vacuum port is facing down, then the flap valves are lo-cated at the top of each vacuum chamber. Are the gaskets or flap valves cracked? If so, the appropriaterepair kit should be purchased. Is the material that is being conveyed in the chambers or nozzles? Foroptimum performance, there should not be any material in the pump. The pump's performance decreas-es as more material gets lodged in the nozzles. Please be careful when cleaning the pump. If a nozzleis broken off or rotated, the pump will need to be replaced. To remove material from the nozzles orchambers, PIAB suggests soaking the pump in water or in water with mild detergent such as dishwashingdetergent. Once the pump has new seals and flap valves and it is clean and put back together, it shouldrun just like a brand new pump.
VACUUM CONVEYORS
24
TROUBLESHOOTING
*Optional part
Type of trouble Cause Position
Poor/no conveying
Low/no vacuum
Low/no pressure in compressed-air pipeline 1 Compressed-air connection
Leakage at seals 3 Seals
Too much carrier air 7 Valves for carrier air
Bottom lid is open/does not work 5 Bottom lid
Hose connection of filter shock/pump is defective 4 Filter shock
Leakage in conveying pipeline/joints 8 Conveying pipeline
High vacuum
Clogged/contaminated filter 2 Filter
Filter shock does not work- clogged filter 4 Filter shock
Too long pump time/short emptying time 9 Control unit
Too little carrier air 7 Valves for carrier air
Damp powder
Clogged conveying pipeline 8 Conveying pipeline
The powder sticks to the inside of the conveyor
Fluidisation does not work/is missing 6 Cone/fluidisation*
Damp powder
Too long pump time/short emptying time 9 Control unit
The filter shock does not work 4 Filter shock
The filter shock does not work
Hose connection of filter shock/pump is defective 4 Filter shock
The valve of the filter shock is defective/contami-nated
4 Filter shock
Low/no pressure to compressed-air pipeline 1 Compressed-air connection
Overfilling of the conveyor Too long pump time/short emptying time 9 Control uni
Powder dust from the pump exhaust Filter defective/incorrectly mounted 2 Filter
VACUUM CONVEYORS
25
TROUBLE SHOOTING GUIDE: PIAB L SERIES PUMP
Problem Possible Causes Possible SolutionsPump will not turn on u On/Off knob safety clip has not been
removed·Ball valve found next to regulator
is in the closed position
u No compressed air available
u Check to be sure safety clip has been
removed and on/off knob is functioning
properly
u Be sure ball valve is turned so handle is
inline with compressed air line
u Problem with plant compressor or feed
lines, call maintenance
Low vacuum level observed on the pump gauge u Compressed air being fed to the pump is not
at high enough pressure
u Not enough volume of compressed air get-
ting to the pump
u On/Off knob is not fully in on position
restricting air flow
u Ball valve is not open 100% and is restricting
air flow
u Pump is not seated properly on the module
seal
u Module seal is torn or caked with material
causing a leakage point
u A Plug used on connections for tubing going
to control unit is loose or missing
u Leakage is being caused due to the surface
the seal/pump/cover unit was placed on
being dirty, rough, or uneven.
u Something is damaged inside the pump.
Pump is clogged with material, ejector noz-
zles have been damaged, or seals and gaskets
need to replaced.
u Read pressure level on the regulator gauge
while pump is running, if too low adjust
regulator dial until desired pressure of
87psi is reached
u If 87psi cannot be reached on the regulator,
there is not enough volume of air to feed
the pump. Make sure compressed air line
diameter is the proper size and increase if
too small. If diameter correct or larger,
than you need to live with the problem, use
a smaller size pump requiring less air, or
shut off other machinery using air so vol-
ume to pump will increase
u Make sure On/Off knob is pushed com-
pletely in against the pump face
u Adjust ball valve so it allows full volume
of air to flow through compressed air line
(align handle w/ compressed air line)
u Adjust pump/cover unit so it is properly
seated on the seal
u Inspect seal for any tears, worn spots, or
excess material buildup. Clean or replace
as necessary.
u Check 6mm, 8mm, and 12mm plugs used
on air manifold block. Make sure all plugs
are present and are pushed securely into the
fittings (especially the 12mm plug, you
must push very hard to get this plug
entirely into the fitting). Insert any missing
plugs
u Clean away debris if possible or find a new
smooth even surface to place seal/pump/
cover unit onto
u All possible problems listed above have
been checked and found to be correct.
Problem is internal to pump, call mainte-
nance
Pump will not shut off u On/off Knob is not fully in off position
allowing air to bleed into pump
u Something is damaged inside the pump not
allowing internal shuttle valve to function
properly
u Make sure on/off knob is pulled completely
out, into the off position
u On/off knob is pulled completely out, in
the off position and pump continues to run.
Problem is internal to the pump, call main-
tenance
VACUUM CONVEYORS
26
L100 - L1200 COMPONENTS
Spare Parts Kit
3101091(V)(E) Spare Kit MLL100-400, co
nsisting of
:3101140 Flap valve, 3 pcs
.3101136 Side plate gasket, 2 pcs.
3101134 Inlet gasket
MLL200-400, 1 pc
3101092(V)(E) Spare Kit MLL600-800, consisting of
:3101141 Flap valves 300, 3 pcs.
3101136 Side plate gasket, 2 pcs.
3101135 Inlet gasket
MLL800-1600, 1 pc
3101099(V)(E) Spare Kit MLL1200, consisting of:
3101380 Flap valves 400, 3 pcs.
3101136 Side plate gasket, 2 pcs.
3101135 Inlet gaskets
MLL800-1600, 1 pcs.
VACUUM CONVEYORS
27
Pos. Art. No. Designation Number
MLL200
3101056
MLL400
3101057
MLL800
3101058
MLL800
3101058
1 31 00 025 Housing incl. nozzles MLL200 1
31 00 026 Housing incl. nozzles MLL400 1
31 00 027 Housing incl. nozzles MLL800 1
31 00 028 Housing incl. nozzles MLL1200 1
2 31 00 053 Silencer internal MLL 100-400 complete 1 1
31 00 055 Silencer internal MLL 600-800 complete 1
31 00 082 Silencer internal MLL 1200 complete 1
3 31 00 054 Silencer external MLL100-400 complete 1 1
31 00 056 Silencer external MLL600-800 complete 1
31 00 083 Silencer external MLL 1200 complete 1
4* 31 01 140 (V)(E) Flap valve 148 3 3
31 01 141 (V)(E) Flap valve 300 3
31 01 380 (V)(E) Flap valve 400 3
5 31 01 138 Side plate, left 1 1 1 1
6 31 01 137 Side plate, right 1 1 1 1
7* 31 01 136 (V)(E) Side plate gasket 2 2 2 2
8 31 01 174 Panel holder 148 2 2
31 01 175 Panel holder 300 2
31 01 377 Panel holder 400 2
9 31 01 016 Panel MLL 100, 400, complete 1 1
31 01 017 Panel MLL 600-800, complete 1
31 01 018 Panel MLL 1200, complete 1
10 31 00 029 Remote valve G1/2" without filter housing 1 1 1 1
11 31 07 170 Barrel nipple KR1/2" - KR1/2 "1 1 1 1
12 31 07 031 Hose connector M5 D=2 incl. washer 4 4 5 5
14 31 07 212 Plug R1/8 "2 2 2 2
15 31 13 743 Nylon washer D=14 x 9,8 x 1 2 2 2 2
16 3113752 Screw MFX 4 x 10 A2 22 22 22 22
17 31 07 223 Compressed air filter 1 1 1 1
18 31 07 120 Filter housing 1/2" remote valve 1 1 1
31 07 291 Filter housing 3/4" remote valve 1
19 33 90 196 Straight adaptor 1/2" D=12 1 1
20 31 07 739 Hose connector 12-1/2 "1 1
21 31 01 131 Inlet gauze MLL 200-400 1 1
31 01 132 Inlet gauze MLL 800-1200 1 1
22* 31 01 134(V)(E) Inlet gasket MLL 200-400 1 1
31 01 135(V)(E) Inlet gasket MLL800-1600 1 1
23 31 16 124 Connecting flange MLL200-400 1 1
31 16 128 Connecting flange MLL800-1200 1 1
24 31 13 664 Screw MC6S 5 x 20 A2 8 8
31 13 669 Screw MC6S 6 x 20 A2 8 8
25 31 13 728 Nylon washer D=5,3 x 10 x 1 8 8
31 13 614 Nylon washer D=12,5 x 6,4 x 1,6 8 8
26 31 01 400 Cover plate MLL 1 1 1 1
27 31 01 401 Sealing Cover plate MLL 1 1 1 1
29 33 90 606 Reducer 6/4 2 2 2 2
30 33 90 306 Angle connection D=6 2 2 2 2
31 33 90 601 Nylon hose D=6/4 0.1m 0.1m 0.1m 0.1m
VACUUM CONVEYORS
28
MLL PANEL COMPONENT
Pos. Art. No. Designation Number
Panel
MLL 200,400
31.01.017
Panel
MLL600,800
31.01.017
Panel
MLL1200
31.01.018
1 31 01 366 Panel MLL 200, 400 1
31 01 368 Panel MLL 600 800 1
31 01 376 Panel MLL 1200 1
2 31 01 602 Vacuum gauge 1 1 1
3 31 07 072 Quick connection JG 6/4-M5 1 1 1
4 31 07 074 Quick connection JG 6/4-M5 1 1 1
5 31 07 010 Actuating valve 1 1 1
6 31 16 055 Shuttle valve 1 1 1
7 31 07 031 Hose connector M5, D=2 with washer 5 6 6
8 31 07 645 Hose 4x2 polyurethane 1.1m 1.2m 1.2m
9 31 01 603 Manometer 1 1
VACUUM CONVEYORS
29
INSIDE COMPONENTS OF MLL PUMPS
VACUUM CONVEYORS
30
INSIDE COMPONENTS OF COMPRESSED AIR INLET FOR MLL PUMPS
Pos. Art. No. Designation
17 31.07.111 Barrel Connector R3/8
17 31.07.194 Barrel Connector M24xM24
25 31.07.031 Hose Connector M5 D=2
26 31.07.030 Hose Connector M5 D=4
27 31.16.055 Shuttle Valve
28 31.07.626 Hose, Nylon 4x2
29 31.07.640 Hose, Nylon 6x4
30 31.07.120 Filter Housing 1/2"
30 31.07.291 Filter Housing 3/4"
32 31.07.223 Compressed Air Filter
31 31.13.739 O-ring 34.2x3 nitrile
33 31.07.116 Valve Housing
34 31.13.626 O-ring 11.5x3 nitrile
34 31.13.803 O-ring 16x3 nitrile
35 31.07.115 Piston for remote valve
35 31.07.191 Piston for remote valve
36 31.13.627 O-ring 24.2x3
37 31.07.119 Cover for Remote Valve
VACUUM CONVEYORS
31
L100 CLASSIC COMPONENTS
VACUUM CONVEYORS
32
L100 CLASSIC COMPONENTS
Spare parts list for MLD100 34.01.072used for C21 Conveyor
Pos. Art. No. Designation MLD100
1 32.00.002 Housing L/1 1
2 32.00.008 Int Housing incl Nozzle 1
3 32.01.103 Valve Plate DC 1
4 32.01.106 Side Plate HLM 1
5 32.01.134 Panel L250D 1
6 31.01.613 Vacuum Gauge 1
7 32.01.111 Exhaust Plug 4
8 32.01.109 Body Gasket 2
32.01.109V Body Gasket Viton (2)
32.01.109E Body Gasket EPDM (2)
9 32.01.110 Side Plate Gasket 1
32.01.110V Side Plate Gasket (1)
32.01.110E Side Plate Gasket (1)
10 32.01.126 Compressed Air Filter 1
11 32.01.141 Cover Plate 250 1
12 31.01.304 Flap Valve Nitrile 2
31.01.304S Flap Valve Silicone (2)
31.01.304V Flap Valve Viton (2)
31.01.304E Flap Valve EDPM (2)
13 31.01.305 Non-Return Valve Nitrile (1)
31.01.305V Non-Return Valve Viton (1)
31.01.305E Non-Return Valve EDPM (1)
14 31.13.755 Screw MFX 4x30 12
15 31.13.752 Screw MFX 4x10 2
16 33.51.171 Comp Air Nipple 1/8” 1
31.13.652 O-Ring D=9.19x2.6 1
17 33.51.170 Nipple Vacuum 3/4” 1
31.13.890 O-Ring D=22.22x2.6 1
32.01.069 (V) (E) Classic 25-120 Parts Kit
Non-Return Valve 31.01.305 excluded in the Conveyor Pumps
VACUUM CONVEYORS
33
TROUBLESHOOTING GUIDE: CONTROL UNIT CU-1B, PART # 01.03.919
Problem Possible Causes Possible SolutionsNo air to the control unit u Air is shut off
u The 6mm tubing is not connected
u Connect the air supply to the pump (40-100
psi)
u Connect the 6mm tubing to the manifold of
the pump and the 6mm connection on the
control unit
u Turn the compressor ON
u Locate the ball valve for the incoming air
supply
u Open the ball valve
The control unit did not cycle u The color-coded tubing are not connected
correctly
u The color-coded tubing is not pushed com-
pletely into connectors
u The timers are set correctly
u The ON-OFF knob is not in the on position
u Port # 8 (level control) is not plugged
u Port # 6 (fluidization) is not plugged
u Remote Start/Stop connectors are not in
place
u Follow the color for each function of the
control unit
u Connect corresponding color tubing with
matching control function port
u Push the control tubing completely into
control connectors
u Set the timers (A=5sec, B=2sec)
u Turn the ON-OFF knob on the left side of
controller once to "1"
u Put 4mm plug into port #8 (level control)
u Put 4mm plug into port #6 (fluidization)
u Put 4mm plug into port #44, jump using a
4mm tubing between port #42 and port #43
The control unit did not cycle u Component problem inside the control unit u Call PIAB, 1-800-321-7422 to arrange
repair or replacement
Connections for inlets and outlets
NOTE! The connections must be plugged when not in use.
Indications on the control unit
Nylon tube dimension OD/ID
Marking/tube colour Port Function
P-in 6/4 Black 1 Air supply input
Open valve 4/2 Blue 2 Opens bottom valve
Filter shock 4/2 Brown 3 Filter shock signal
Pipe empty 4/2 Transparént 4 Pipe emptying signal
Close valve 4/2 Yellow 5 Closes bottom valve
Fluid 4/2 White 6 Fluidisation signal
Pump 4/2 Green 7 Vacuum pump start signal
Level control 4/2 Grey 8 Level detector
VACUUM CONVEYORS
34
TROUBLESHOOTING GUIDE: CONTROL UNIT CU-2B, PART # 01.03.921
Problem Possible Causes Possible Solutions
No air to the control unit u Air is shut off
u The 6mm tubing is not connected
u Connect the air supply to the pump (40-100
psi)
u Connect the 6mm tubing to the manifold of
the pump and the 6mm connection on the
control unit
u Turn the compressor ON
u Locate the ball valve for the incoming air
supply
u Open the ball valve
The control unit did not cycle u The color-coded tubing are not connected
correctly
u The color-coded tubing is not pushed com-
pletely into connectors
u The timers are set correctly
u The ON-OFF knob is not in the on position
u Port # 8 (level control) is not plugged
u Port # 6 (fluidization) is not plugged
u Remote Start/Stop connectors are not in
place
u Follow the color for each function of the
control unit
u Connect corresponding color tubing with
matching control function port
u Push the control tubing completely into
control connectors
u Set the timers (A=5sec, B=2sec, C=5sec
u Turn the ON-OFF knob on the left side of
controller once to "1"
u Put 4mm plug into port #8 (level control)
u Put 4mm plug into port #6 (fluidization)
u Put 4mm plug into port #44, jump using a
4mm tubing between port #42 and port #43
The control unit did not cycle u Component problem inside the control unit u Call PIAB, 1-800-321-7422 to arrange
repair or replacement
Connections for inlets and outlets
NOTE! The connections must be plugged when not in use.
Indications on the control unit
Nylon tube dimension OD/ID
Marking/tube colour Port Function
P-in 6/4 Black 1 Air supply input
Open valve 4/2 Blue 2 Opens bottom valve
Filter shock 4/2 Brown 3 Filter shock signal
Pipe empty 4/2 Transparént 4 Pipe emptying signal
Close valve 4/2 Yellow 5 Closes bottom valve
Fluid 4/2 White 6 Fluidisation signal
Pump 4/2 Green 7 Vacuum pump start signal
Level control 4/2 Grey 8 Level detector
VACUUM CONVEYORS
35
DIMENSIONCONTROL UNIT CU-1A, CU-1B, CU-2A, CU-2B WITH MOUNTING BRACKET ART. NO. 01 03 918
ART. NO. 01 03 919ART. NO. 01 03 920ART. NO. 01 03 921
VACUUM CONVEYORS
36
FUNCTIONS OF THE CONTROL UNITCONTROL UNIT CU-1A/B, CU-2A/B ART. NO. 01 04 550, 01 04 552
ART. NO. 01 04 540, 01 04 548
A Adjustable time for conveyingB Adjustable time for pipe line emptyingC Adjustable time for emptying of conveyor D 1 = Start of conveyor
0 = Stop of conveyor
CU-1A Art. No. 01 04 550CU-1B Art. No. 01 04 552
CU-2A Art. No. 01 04 540CU-2B Art. No. 01 04 548
VACUUM CONVEYORS
37
THE FOLLOWING FUNCTIONS CAN BE ADJUSTED BY THE OPERATOR
Control unit CU-1A
A Conveying time. Adjustable, 0.1–30 seconds.
C Time for emptying of conveyor. Adjustable, 0.1–30 seconds.
The bottom valve is open when the conveyor is turned off.
Control unit CU-1B
A Conveying time. Adjustable, 0.1–30 seconds.
C Time for emptying of conveyor. Adjustable, 0.1–30 seconds.
The bottom valve is closed when the conveyor is turned off.
Control unit CU-2A
A Conveying time. Adjustable, 0.1–30 seconds.
C Time for emptying of conveyor. Adjustable, 0.1–30 seconds.
B Time for pipe line emptying for each conveying cycle.
Adjustable 0.1–30 seconds.
The bottom valve is open when the conveyor is turned off.
Control unit CU-2B
A Conveying time. Adjustable, 0.1–30 seconds.
C Time for emptying of conveyor. Adjustable, 0.1–30 seconds.
B Time for pipe line emptying for each conveying cycle.
Adjustable, 0.1–30 seconds.
The bottom valve is closed when the conveyor is turned off.
VACUUM CONVEYORS
38
CONTROL UNIT CU-1B, BOTTOM VALVE NC ART. NO. 01 04 552
VACUUM CONVEYORS
39
PNEUMATIC DIAGRAMCONTROL UNIT CU-1A, BOTTOM VALVE NO ART. NO. 01 04 550
(
VACUUM CONVEYORS
40
CONTROL UNIT CU-1B, BOTTOM VALVE NC ART. NO. 01 04 552
VACUUM CONVEYORS
41
CONTROL UNIT CU-2B, BOTTOM VALVE NC ART. NO. 01 04 548
VACUUM CONVEYORS
42
TROUBLESHOOTING GUIDE: CONTROL UNIT PPT/R, PART # 01.06.066
Problem Possible Causes Possible Solutions
No air to the control unit u Air is shut off·
u The 6mm tubing is not connected
u ·Connect the air supply to the pump
(40-100 psi)·
u Connect the 6mm tubing to the mani-
fold of the pump and the 6mm connec-
tion on the control unit·
u Turn the compressor ON·
u Locate the ball valve for the incoming
air supply·
u Open the ball valve
The conveyor did not cycle
The conveyor does not completely shut
off
u ·The color-coded tubing are not connected
correctly·
u The color-coded tubing is not pushed com-
pletely into connectors·
u The timers are set incorrectly
u ·Timer shuts off immediately·
u The O-ring may be misplaced or cracked in
the compressed air inlet of the pump (Not
valid with Classic L100)·
u One of the O-rings on the PPT/R timer
could be missing or cracked·
u Inadequate air pressure for shifting the shut-
tle valve on the pump (Not valid with Clas-
sic L100)
u ·Follow the color for each function of
the control unit·
u Connect corresponding color tubing
with matching control function port·
u Push the control tubing completely into
control connectors·
u Set the timers (V1=5sec, V2=2sec)V1
= 01.04.477 / V2 = 01.04.476
Timers do not contain stops / They will
continue turning, changing from maxi-
mum setting to minimum setting·
u Replace timer ·
u Replace O-ring on compressed air inlet
of the pump·
u Replace the O-ring on the PPT/R in the
area of air leak·
u Check air supply pressure
The control unit did not cycle u ·Material obstructing bottom door·
u To high (40 to 100 psi) a pressure coming
from the regulator on the PPT/R
u ·Clear any material that is obstructing
bottom door·
u Adjust the regulator on the PPT/R
clockwise until a pressure gauge
inserted into the PPT/R regulator reads
30 to 35 psi
Pump and PPT/R are cycling on and off,
but the bottom door will not open all the
way or at all
u ·The conveyor may be packed with material
/ preventing the release of vacuum in the
conveyor·
u To low (0 to 25 psi) a pressure coming from
the regulator on the PPT/R·
u Bottom door may be sticking to the bottom
seal
u ·Open conveyor and clean out all of the
productReset the PPT/R timers to 5
seconds on and 10 seconds off (Adjust
on and off timers to reduce waiting
time between cycles)·
u Adjust the regulator on the PPT/R
counter clockwise until a pressure
gauge inserted into the PPT/R regulator
reads 30 to 35 psi·
u Clean bottom seal, removing any mate-
rial stuck to it and any residue left
behind by the material
VACUUM CONVEYORS
43
FUNCTIONS OF THE CONTROL UNIT
A Adjustable time for conveyingB Adjustable time for emptying of conveyorC Regulator for opening of valve
VACUUM CONVEYORS
44
PNEUMATIC DIAGRAM(
COMPONENT LAYOUT
VACUUM CONVEYORS
45
TIME SIGNAL DIAGRAM
MOUNTING
VACUUM CONVEYORS
46
Connections for inlets and outlets(
General recommendationsFeed pressure: 0.4–0.6 MPa (58–87 psi)
Quality: The equipment requires dry and filtered(filtration grade 5 micron) compressed airaccording to ISO standard 8573.1, qualityclass 3.
We recommend that PIAB’s regulator kitshould always be used in order to ensureproper function. Use the 1/2" regulator kitfor 100–400 pumps (Art. No. 01 04 490)or regulator kit 1" for 600–1600 pumps(Art. No. 01 04 491).
Indications on the control unit
Nylon tube dimensionOD/ID
Marking/tube colour Port Function
P-in 6/4 Black 1 Air supply input
Pump 4/2 Green 2 Starts vacuum pump
Shock 4/2 Brown 3 Filter shock
Close valve 4/2 Yellow 4 Closes bottom valve
Open valve 4/2 Blue 5 Opens bottom valve
VACUUM CONVEYORS
47
DISASSEMBLING A PPT/R CONTROL
Please go through the other trouble shooting methods before disassembling the timers. Under clean, normal con-
ditions the PPT /R does not require routine maintenance. However in a dusty, dirty environment, the timers will need
to be re-lubricated. Please do not wash or spray the timers with water. The timers may be sent back and PIAB can
re-lubricate them, or the following instructions can be followed.
Helpful hints:
1. Make note of how each individual timer is installed. It is possible to install the timers upside down (rotated
180°), especially in the CU control. Please refer to drawing on page 37.
2. Only remove one timer from the controller at a time for service. The CU controller has two different types of
timers that cannot be mixed.
3. Only a small amount of lubrication is necessary, too much lubrication can damage the controller.
Procedure:
1. The A10 and C10 timers are composed of two parts. Separate the top of the timer from the base of the timer
by completely unscrewing and backing out the two screws found under the head assembly. Once the parts
have been separated, be careful not to loose any parts that may be loose. Make sure there are 3 o-rings on
the bottom of the timer. If one is missing or cracked this could be the problem.
2. The top of the timer is the portion that includes the adjustment knob. Set this portion aside.
3. The base of the timer is the portion that includes the mounting screws. This will need to be disassembled
further.
4. On the top of the base there is a brass assembly that is pressed into the black plastic base. Using a small
screwdriver or knife, pry this brass assembly out. There is an o-ring around the circumference of the brass
plate where it is in contact with the base, be very careful not to damage this o-ring.
5. The brass pieces can then be lifted from the base and separated.
6. If the brass pin will not slide easily, smear a small amount of lubricating grease around the brass pin. Try not
to use an excessive amount, as it can build up and clog the small orifices in the timer assembly. Do not put
any grease on the top of the pin that can cover the hole. If the pin slides easily, it does not need to be lubri-
cated.
7. Reassemble the brass assembly and put the assembly back into the base.
8. Push the brass pin down into the base assembly several times to confirm that it is moving smoothly and is
not sticking. It should pop up rather quickly and immediately.
9. Reassemble the top and base pieces of the timer and reinstall onto the base of the PPT/R Timer or CU Timer.
These PPT/R Timers are wear parts. There is a bellows suction cup inside of the timer that will wear after time. If
the timer has been re-lubed, all of the o-rings are in good condition, and it still will not work - a new timer will need
to be purchased.
VACUUM CONVEYORS
48
TROUBLESHOOTING GUIDE: CONTROL UNIT VCC-EP, PART # 34.07.016
Problem Possible Causes Possible SolutionsNo air to the control unit u ·Air is shut off·
u The 6mm tubing is not connected
u ·Connect the air supply to the pump
(40-100 psi)·
u Connect the 6mm tubing to the mani-
fold of the pump and the 6mm connec-
tion on the control unit·
u Turn the compressor ON·
u Locate the ball valve for the incoming
air supply·
u Open the ball valve
The conveyor did not cycle
The conveyor does not completely shut
off
u ·The color-coded tubing are not connected
correctly·
u The color-coded tubing is not pushed com-
pletely into connectors·
u Inadequate air pressure to the controller (air
supply port)·
u No air signal coming out of port #1 on the
VCC-EP when valve is manually depressed
or fired electronically ·
u The O-ring may be misplaced or cracked in
the compressed air inlet of the pump (Not
valid with L100)·
u Inadequate air pressure for shifting the shut-
tle valve on the pump (Not valid with L100
u ·Follow the color for each function of
the control unit·
u Connect corresponding color tubing
with matching control function port·
u Push the control tubing completely into
control connectors·
u Turn air supply to pump off / Discon-
nect the air supply tubing from the
VCC-EP control. Plug air supply tub-
ing into a pressure gauge, turn air sup-
ply on to the pump and verify air
supply pressure going to the VCC-EP
(40 to 100 psi)·
u Verify air supply to pump and VCC-EP
control unit
u ·Replace O-ring on compressed air
inlet of the pump·
u Check air supply pressure going into
air supply port of VCC-EP (40 to 100
psi)
Conveyor pump runs continuously and
will not shut off
u ·Material obstructing bottom door·
u Missing or damaged bottom seal
u ·Clear any material that is obstructing
bottom door·
u Check for the presence of a bottom seal
(clean seal if present)·
u Replace bottom seal
Pump and VCC-EP are cycling on and
off, but the bottom door will not open all
the way or at all
u ·The conveyor may be packed with material
/ preventing the release of vacuum in the
conveyor·
u Bottom door may be sticking to the bottom
seal·
u Signals to and from valves 4 and 5 on VCC-
EP control
u ·Open conveyor and clean out all of the
product·
u Clean bottom seal, removing any mate-
rial stuck to it and any residue left
behind by the material·
u Make sure there is a simultaneous elec-
tronic input to valves 4 and 5 on the
VCC-EP control or the bottom door
will not open
VACUUM CONVEYORS
49
Connections for inlets and outlets
Indications on the valve unit
(
General recommendationsFeed pressure: 0.4–0.6 MPa (58–87 psi)
Quality: The equipment requires dry and filtered(filtration grade 5 micron) compressed airaccording to ISO standard 8573.1, qualityclass 3.
We recommend that PIAB’s regulator kitshould always be used in order to ensureproper function. Use the 1/2" regulator kitfor 100–400 pumps (Art. No. 01 04 490)or regulator kit 1" for 600–1600 pumps(Art. No. 01 04 491).
Port name Port number Function
Air supply 0 Air supply inputOperating pressure 0.6 MPaPower supply 24V DC
Conveyor pump 1 Connected to start valve for vacuum pump
Fluidisation 2 Connected to 2/2 valve for start of fluidisation
Filter shock 3 Connected to 3/2 valve for filter shock
Discharge open 4 Connected to actuator to open bottom flap
Discharge close 5 Connected to actuator to close bottom flap
Electric inputs For electronic control signals to the connection block (2xØ6 mm)
Port label Nylon tube dimensionOD/ID
Tube colour Port Function
Air supply 6/4 Black 0 Air supply input.
Conveyor pump 4/2 Green 1 Connected to start valve for vacuum pump.
Fluidisation (Spare) 4/2 White 2 Connected to 2/2 valve for start of fluidisation.
Filter shock (Spare) 4/2 Brown 3 Connected to 3/2 valve for filter schock.
Discharge open 4/2 Blue 4 Connected to actuator to open bottom flap.
Discharge close 4/2 Yellow 5 Connected to actuator to close bottom flap.
Electric inputs 4/2 For electric control signalsto the connection block (2xØ6mm)
VACUUM CONVEYORS
50
VALVE CONNECTIONS FOR THE VCC-EP
VACUUM CONVEYORS
51
TROUBLESHOOTING GUIDE: LEVEL DETECTOR 24 VDC, PART # 01.00.267
TROUBLESHOOTING GUIDE: INJECTION UNITS, PART # 34.04.019 - 34.04.023
Problem Possible Causes Possible SolutionsConveyor will not turn on u Air is shut off·
u Product is covering the sensor on the Level
Detector(giving a false high level signal
u No 24 VDC going into the level detector
u Incorrect pressure coming out of port #8 on
CU controller
u Air signal tubing is not properly installed
into level detector or CU controller
u Level sensor is malfunctioning
u Connect the air supply to the pump
(40-100 psi)
u Connect the 6mm tubing to the mani-
fold of the pump and the 6mm connec-
tion on the control unit
u Open conveyor and remove any prod-
uct that is covering the level detector
u Connect power supply / If there is a
loss of power the CU controller will
shut down and need to be manually
reset
u Place an air pressure gauge into port #8
on the CU controller and verify air
pressure venting from port #8 is 30 - 40
psi
u Push tubing into each respective fitting
checking to make sure there is no air
leaking from each fitting
u Call PIAB, 1-800-321-7422 to arrange
repair or replacement
Problem Possible Causes Possible Solutions
Injection unit will not cycle u Air is shut off
u Pinch valve remains open
u Vacuum switch does not read any vacuum
u Pinch valve remains closed
u Pinch valve bladder is worn or ruptures
u Connect the air supply to the unit (87
psi)
u Connect the 6mm tubing to the air in
port on the switch control box
u Air supply to the injection unit is
greater than 87 psi, decrease air supply
u Verify that 4mm tubing is connected
between the vacuum port on the pump
(see diagram) and the vacuum port on
the switch control box
u Adjust vacuum switch to lower vac-
uum level by opening switch control
box and turn knob on top of vacuum
switch until pinch valve opens
u Call PIAB, 1-800-321-7422 to arrange
repair or replacement
VACUUM CONVEYORS
52
LEVEL DETECTOR
� Function:The PIAB level detector is used together with the PIAB control unit, CU, to stop the conveyor when the detector is activated.
Technical data for capacitive gauge
Model Art. No. Feed pressureMPa (psi)
Voltage VDC Housingmaterial
Degree of protection
Weightg (lb)
Operating temperature°C (°F)
Level detector 01 00 267 0.2–0.6 (29–87) 24 PC, POM IP 54 622 (21.9) 0–50 (32–122)
Switching hysteresis Operatingtemperature °C (°F)
Degree ofprotection
Cable VoltageVDC
Output current max, mA
Max switching power W
10% of sensing distance –30 –70 (–22–158) IP67 PVC 3x0,5 mm2 10–35 300 7.2
Art. No. 01 00 267
VACUUM CONVEYORS
53
PNEUMATIC INJECTION VALVE
VACUUM CONVEYORS
54
CLEANING OUT A PACKED CONVEYOR
There are many reasons why a conveyor can get overly full of material. Most of the reasons have beennoted above. The important factor is how to clean the conveyor out. The easiest way to take apart theconveyor is to remove clamps and remove the pump and filter assembly. If there is not enough headroom,start from the bottom and remove module by module.
After removing the material from the main body of the conveyor, check to see if the material got pastthe filter. If it did, all of the parts above the filter should be cleaned out until there are no signs of thematerial. This includes any tubing and the air shock. Make sure the valve on the air shock is cleaned offand moves in and out easily. Please refer to diagram below. If the valve tends to stick, lubricate it. If thematerial is all the way up into the pump, please see page 23 for directions on how to clean out the pump.
VACUUM CONVEYORS
55
MAINTENANCE SCHEDULE
Explanation of the schedule
1. Check the feed pressure:The work pressure of the compressed-air supply ischecked during operation of the conveyor/pump.The operational pressure should be approximately0.5–0.6 MPa (72–87 psi).
2. Check the sealing:Check the conveyor by disconnecting the convey-ing hose/pipeline and applying a sealing rubbersheet against the end of the sleeve coupling whilethe pump is in operation. Read the vacuum levelon the vacuum gauge of the pump and comparethe value with the data sheet for the pump that isused. Repeat this checking procedure, but withthe feeding end of the conveying pipeline systemsealed.
3. Checking the pressure drop during conveying ofpowder:Read the vacuum gauge of the pump during nor-mal operation/conveying. Compare the vacuumlevel with the values obtained when checkingstart-up of the conveying system.
4. Checking the pressure drop during idling opera-tion:Read the vacuum gauge of the pump during idlingoperation without conveying any powder. Carry outthe first check at start-up (date of start) and doc-ument the value in the table to the right above.When the pressure drop during idling has risen(and the vacuum level has decreased) by approxi-mately 5–10 -kPa (1.5–3"Hg)as compared to thestart value, this is an indication that the filterneeds to be washed/changed.
5. Washing the filter:A contaminated Pitex filter bag can be washed in-stead of being changed. The filter can normally bewashed 2–4 times. The filter bag can be washedin a normal washing machine in 40°C (104°F)“cold wash” or corresponding hand wash.
Gore Sinbran filters should be cleaned carefullywith a soft brush under running water at low pres-sure in order not to destroy the membrane of thefilter. Gore Sinbran filters may not be washed butthey can be sterilised for 30 minutes at 120°C(248°F).
Time interval Check/messure Daily Each
monthEvery second
monthEvery sixth
monthAccording to experience
Date of start of new installation
..................................
Pressure drop at idling at date of start
............. -kPa (-in Hg)
Date of filter change or filter washing
1 Check of feed pressure X
2 Check of sealing,conveyor/system
X
3 Check of pressure drop during conveying
X
4 Check of pressure drop during idling
X
5 Washing of filter X (X)
6 Change of filter/Check of air shock function
X (X)
7 Emptying of filter regulator/change of filter kit
X
8 Dismounting,cleaning/washing and checking
X X (X)
VACUUM CONVEYORS
56
6. Change of filter:NOTE: Only for Pitex filtersA change of filter shall be made at least once eve-ry six months or after having washed the filter 2–4 times. Notice that changing/washing of filtermay, due to hygienic reasons in food applications,be required at shorter intervals.
7. Emptying of filter regulator/change of filter kit:Check and dispose of possible contamination andwater in the filter regulator on the feed pipelineonce every two months. The filter kit of the filterregulator should be replaced once every year.
8. Dismantling, cleaning and checking: The conveyor should be dismantled regularly forchecking and cleaning. For sanitary reasons, inthe the chemical and food industry, daily disman-tling and washing are sometimes required.
CLEANING THE CONVEYOR
The whole conveyor should be disassembled at reg-ular intervals for checking and cleaning. Due to hygi-enic reasons in the food and pharmaceutical indus-tries there may be requirements for daily washingaccording to applicable regulations.
NOTE: The conveyor is not designed for CIP – CleanIn Place.
The supply of compressed air shall be disconnectedfrom the pump. Dismount the pump and the upperpart of the filter unit and the air shock tanks. Allthese parts are on the “clean side” of the filter, i.e.,they do not come in contact with the conveyed pow-der. Loosen the remaining clamp rings and dismountthe modules, seals (see below) and the filters (seebelow). The steel parts can be washed with waterand detergent according to local regulations. It is im-portant to clean all parts that come in contact withthe conveyed powder.
SealingsThe material in the silicone sealings has been testedand approved according to the 3-A Sanitary Stand-ards No. 18-03, Class II. This means, among otherthings, that it has been tested in alkaline cleanertest solution for 22 hours at 82°C (179.6°F) and ni-tric acid (0.5%) for 22 hours at 82°C (179.6°F).
The material in the nitrile sealings has been testedand approved according to the 3-A Sanitary Stand-ards No. 18-03, Class III. This means, among otherthings, that it has been tested in alkaline cleanertest solution for 22 hours at 82°C (179.6°F) and or-tophosphoric acid (1.0%) for 22 hours at 82°C(179.6°F).
The silicone- and nitrile rubber materials are in com-pliance with FDA CFR 21 § 177.2600 ”Rubber arti-cles intended for repeated use”.
WARRANTY
PIAB gives a 5-year warranty for its conveyors andvacuum pumps. For accessories the guarantee is 1year. The warranty does not apply to filters and otherconsumable par
VACUUM CONVEYORS
57
NOTES
VACUUM CONVEYORS
58
NOTES
VACUUM CONVEYORS
59
NOTES
ASIA PACIF IC (S INGAPORE)Asia Pacific Pte Ltd
27 Mandai Estate #05-02Innovation Place Tower 2SINGAPORE 729935Tel 65-6368 2348Fax 65-6368 [email protected]
AUSTRALIAVacuum Technologies Pty. Ltd.
17 Southfork DriveKILSYTH, VIC 3137Tel 61-3 9728 8653Fax 61-3 9728 [email protected]
BRAZILDo Brasil Ltda.
Av. Indianopolis, 1725 - Planalto PaulistaBR-04063-003 SAO PAULO-SPTel 55-11 5589 8955Fax 55-11 5589 [email protected]
FRANCES.A.
Parc d’Entreprises EsplanadeSaint Thibault-des-VignesFR-77462 LAGNY SUR MARNE CEDEXTel 33-1 64 30 82 67Fax 33-1 64 02 87 [email protected]
GERMANYVakuum GmbH
Pfingstweide 41D-61169 FRIEDBERGTel 49-6031 71840Fax 49-6031 [email protected]
GREAT BRITAINLtd.
P.O. Box 43GB-LOUGHBOROUGH Leicestershire LE12 8NYTel 44-1509 814 280Fax 44-1509 814 [email protected]
ITALYITALIA Srl
Via Schiaparelli, 10IT-10148 TORINOTel 39-011 226 36 66Fax 39-011 226 21 [email protected]
PIAB G IVES YOU SERVICE ALL OVER THE WORLD
JAPANJapan Ltd.
3-11-23 Hikawacho, Todo-shi,Saitama-ken 335-0027Tel 81-48 443 9148Fax 81-48 443 [email protected]
L AT IN AMERICA (COLOMBIA )Latin America
Carrera 16 No. 86A-76SANTA FE DE BOGOTÁ, ColombiaTel 57-1 636 1953Fax 57-1 636 [email protected]
SOUTH AFRICA(Pty) Ltd.
P.O. Box 23512CLAREMONT, Cape Town 7735Tel 27-21 447 5110Fax 27-21 448 [email protected]
SPAINVacío S.L.Ctra. Llobatona, s/n, nave 12ES-08840 VILADECANS BARCELONATel 34-93 638 90 91Fax 34-93 638 08 [email protected]
SWEDENAB
Box 4501SE-183 04 TÄBYTel 46-8 630 25 00Fax 46-8 630 26 [email protected]
SWITZERL ANDVakuum AG
Industrie Neuhof 9Postfach 400CH-3422 KIRCHBERGTel 41-34 448 24 24Fax 41-34 448 24 [email protected]
USAUSA, Inc.
65 Sharp StreetHINGHAM, MA 02043Tel 1-781 337 7309
1-800-321-PIABFax 1-781 337 [email protected]
www.piab.com
TSH
OO
T03