MACHINE: FEEDING DEVICE

TYPE: B50.17.00.00.00

OPERATION MANUAL

ZMM “STOMANA” JSC - SILISTRA

B50.17.00.00.00

OPERATION MANUAL

ATTENTION: Before commissioning it is necessary to get acquainted with all the

instructions of this manual. The manufacturer is not responsible for

damages caused due to improper operation of the machine or amendments

in the design.

Page 2

INFORMATION

In order to work with the Feeder, you have to have Fine adjustable fence for bandsaw, produced

in ZMM Stomana JSC- Bulgaria.

1. Technical data

Feeder

Speed of feeding 1-10 m/min – frequency adjustment

Feeding belt Sandpaper- textile base

HERMES – RB 346 MX / P60 / L=1820 mm / B=150 mm

2. Installing

Dismount the aluminum profile A, support B and the handles C from the fine adjustable fence, from

fig. 1 to the position on fig. 2.

Mount the feeding beam А (fig.3) on the place of the dismounted elements of the fence, and the clamp-

ing roller В in the table groove.

Install the electric box А (fig.4) behind the column. Your electric specialist must connect the elec-

tric box to the electric system of the bandsaw, according the electric diagram.

i

Fig. 1

A

B

C

Fig. 2

A

Fig. 4 Fig. 3

A

B

C

D

G

F

E

Page 3

3. Working with the feeder

Through pushing of button F (fig.3) you will start feeding, and through a red button G you will stop

the feeder. From the potentiometer Е you can adjust the speed of feeding. If you connect correctly the

feeder to the bnadsaw through pushing of bandsaw stop will stop and the feeder also.

Clamping roller В can be adjusted from the handle D, and the tension of the spring- from the nut С.

Feeding beam А can be moved and adjusted like the aluminum fence.

4. Wiring diagram

Page 4

B50.17.00.00.00 FEEDING DEVICE

1 B50.17.03.00.00 COVER, LEFT 1

2 ISO 7380 SCREW М 5Х 8 24

3 B50.17.00.00.14 PLATE 1

4 B50.17.00.00.04 TENSOR ROLL 1

5 B50.17.01.00.00 SUPPORTING BEAM 1

6 DIN 7980 SPRING WASHER 6Н 12

7 HERMES-RB 346 MX BAND B=150-L=1820-Р60 1

8 B50.17.00.00.09 RETENTIVE PLATE 2

9 B50.17.00.00.11 LEAD BAND 1

10 PAP BUSHING PAP 2020 P10 2

11 DIN 912 SCREW М8х60 2

12 B50.17.00.00.05 TENSOR AXLE 1

13 B50.17.00.00.12 COVER, MIDDLE 1

14 B50.17.00.00.15 TIGHTEN STUD 2

15 DIN 7349 WASHER М10 2

16 A583-80-М10 HANDLE М10 2

17 B50.17.00.00.13 SLIDING PAD 1

18 B50.17.16.00.00 PRESSING ROLL 1

19 RADIAL-BEARING 6001-ZZ 1

20 KZM 00.12.00.08 WASHER Ø21ХØ40Х2 2

21 B50.17.00.00.06 MOTIVE ROLL 1

22 B50.17.02.00.00 COVER, RIGHT 1

23 DIN 912 SCREW М 6Х16 4

24 DIN 933 BOLT М6Х16 8

25 B50.17.00.00.10 FLANGE FOR REDUCTION GEAR- VF 44 P46 P P63-B14 1

26 DIN 134 WASHER M 8 4

27 DIN 7980 SPRING WASHER 2-8Н 4

28 DIN 933 BOLT М 8х25 4

29 DIN 6885A COTTER 6X6X40 1

30 DIN 6885A COTTER 6X6X20 2

31 B50.17.00.00.07 SHAFT 1

32 DIN 471 RING FOR SHAFT Ø18 1

33 BONFIGLIOLI REDUCTION GEAR VF 44 P46 P P63-B14 1

34 SPE MOTOR FOR REDUCTION GEAR B14 0,25 kW 1

Page 5

ZMM STOMANA JSC - SILISTRA

...............................

/date of production/

QUALITY CERTIFICATE

We do certify that the Feeding device B50.17.00.00.00 as per Production number

_________________ was duly checked and controlled.

It conforms to the technical documentation and to the Bulgarian State Standard 9136-

87.

Inspector:...................

/date/

Manager:…………….

Page 6

ZMM STOMANA JSC - SILISTRA

...................................

/date of production/

...........................................

/Number of warranty certificate/

WARRANTY CERTIFICATE

Description of item: Feeding device B50.17.00.00.00

Model: .......................................

Production number...................................................

Passport No................................

Components .........................................

Warranty period: .............................................

The machine is purchased by ...............................................................................

Invoice No.............................

This machine is produced under approved technical documentation in the producing

plant and according to the effective norms in Bulgaria.

The producer guarantees the proper operation of the machine for 12 months upon the

date of shipment provided that all requirements related to the assembly, servicing and

operation as indicated in this Manual, are observed.

All claims produced to us must be effected upon presentation of this warranty

certificate.

Page 7

Service unit Date of

receipt

Order No Kind of repair

works

Date of

delivery

Checked

by

.......................... Seller: ......................

(date) Buyer :.....................

Address: ...........................