c07a10 Tft Management User Manual

7/29/2019 c07a10 Tft Management User Manual

1/20

Rev A FIDS TFT Management User Manual

IT Systems

Indian Airports

FIDS

TFT Management

User Manual

Revision A

Issue Date 14 October 2009

Page 1 of 20

s o l a r iu d i


2/20


TABLE OF CONTENTS

1 Introduction ..........................................................................................................................3

2 TFT MANAGER APPLICATION ............................................................................................4

2.1 GROUPS .........................................................................................................................5

2.2 DEVICES .........................................................................................................................9

2.3 TIMES ...........................................................................................................................11

2.4 LOAD NEW CONFIGURATION ....................................................................................16

2.5 EMERGENCY ...............................................................................................................19

Page 2 of 20

s o l a r iu d i


3/20


1 Introduction

The aim of this document is to provide the guidelines to use the Solari application namedTFT MANAGER.

The goal of TFT MANAGER application is to build and manage the time rules necessary toswitch-off and switch-on the lamps of all the TFT devices installed in an I.D.S. (InformationDisplay System), in order to safeguard the lifetime of each device.

Page 3 of 20

s o l a r iu d i


4/20


2 TFT MANAGER APPLICATION

The first operation to do for using TFT Manager Application is, obviously, login.

Its enough to open the browser and point the URL /tftmanager (relative to the lbserver).

Example :

http://lbsrv/tftmanager/

Starting the TFT MANAGER application the main window printed in FIG.1 will be displayed.

FIG.1 : MAIN WINDOW

At the top of the screen the BUTTON BAR with the following buttons will appear:

- GROUPS- DEVICES- TIMES- LOAD NEW CONFIGURATION- EMERGENCY

Page 4 of 20

s o l a r iu d i


5/20


2.1 GROUPS

FIG.2 : GROUPS FORM

Pressing GROUPS button the form printed in FIG.2 will be displayed.

The user has the possibility to create, delete or modify groups, using the GROUP NAMEcombo box.

What is a group ?

A group is a logical subdivision for one or more TFT devices with the same switch on-off timerules. For example in an airport application we can consider all gate TFT devices belonging tothe group GATES, all the check-in TFT devices belonging to the group CHECK-IN etc.

Splitting the TFT devices in different groups can be helpful because the application is

designed to define a single switch on-off time rule that can be automatically assigned to all

TFT devices belonging to the same group (see chapter 2.3.2).

Page 5 of 20

s o l a r iu d i


6/20


2.1.1 ADD GROUP

FIG.3 : ADD GROUP

Pressing ADD GROUP button the form printed in FIG.3 will be displayed.

To add a new group the fields Group Name and Description must be both meaningful,otherwise an error message will be displayed.

Press CONFIRM to apply the insertion of the new group or EXIT to abort the operation.

Page 6 of 20

s o l a r iu d i


7/20


2.1.2 DESCRIPTION

FIG.4 : MODIFY DESCRIPTION

Pressing MODIFY DESCRIPTION button the form printed in FIG.4 will be displayed.

Group Name field is protected: the user can only modify the description.

Press CONFIRM to apply the description update or EXIT to abort the operation.

Page 7 of 20

s o l a r iu d i


8/20


2.1.3 DELETE GROUP

FIG.5 : DELETE GROUP

Pressing DELETE GROUP button the form printed in FIG.5 will be displayed.

Press CONFIRM to apply the deletion of the selected group or EXIT to abort theoperation.

Page 8 of 20

s o l a r iu d i


9/20


2.2 DEVICES

FIG.6 : DEVICES FORM

Pressing DEVICES button the form printed in FIG.6 will be displayed.

Getting data (automatically) from the SYSTEM CONFIGURATOR, the complete list of allsystem devices (TFTs, LED devices, FLAP devices, etc) will be displayed (columns:DEVICE and DESCRIPTION).

1st STEP

The user must define all TFT devices, checking the column CHECK IF TFT. In this way allother devices will not be handled by the application.

2nd STEP

The user can create the relationship between TFT and GROUP, using the GROUP combobox. The fields:

- SWITCH OFF- SWITCH ON- WEEKLY FREQUENCY- ENA / DIS

cannot be modified with this function and could be empty.

Press SAVE to apply all the updates or EXIT to abort the operation.

Page 9 of 20

s o l a r iu d i


10/20


P.S. If ENA / DIS flag is 0 the switch on-off time rules are not handled !!!

If in the peripheral system configuration the number of TFT devices is greater than thenumber of other devices the button CHECK ALL AS TFT can be helpful.

Pressing on CHECK ALL AS TFT button all devices will be checked as TFT.

Remember to press SAVE to apply all the updates.

The function of DISPLAY ONLY TFT button is to have a complete list of TFT devices only(remember: tft device means controller with flag CHECK IF TFT enabled).

FIG.6/A : DEVICES FORM ONLY TFT CONTROLLERS

Pressing DISPLAY ALL DEVICES button is necessary to obtain thecomplete list of all devices.

Page 10 of 20

s o l a r iu d i


11/20


2.3 TIMES

FIG.7 : TIMES FORM

Pressing TIMES button the form printed in FIG.7 will be displayed.

Through this function the user can define the switch on-off time rules using:

- GLOBAL DEFINITION- GROUP TIMES- DEVICE TIMES

Page 11 of 20

s o l a r iu d i


12/20


2.3.1 GLOBAL DEFINITION

FIG.8 : GLOBAL DEFINITION

Pressing GLOBAL DEFINITION button the form printed in FIG.8 will be displayed.

The below table describes the meaning of each field.

FIELD DESCRIPTION NOTES

Switch OFF Time TFT lamps switch-off time

Switch ON Time TFT lamps switch-on time

Weekly Frequency Days of week in which the time-rulesare valid

If all days are DISABLEDthe time-rules are NOTHANDLED

Time rules ENA/DIS Flag to ENABLE or DISABLE time-rules If flag is DISABLED thetime-rules are NOTHANDLED

Pressing ASSIGN THE DISPLAYED TIME RULES TO ALL TFT DEVICES button ispossible to assign, automatically, the defined time rules to all devices checked as TFT.

Page 12 of 20

s o l a r iu d i


13/20


FIG.9 : GLOBAL DEFINITION - CONFIRMATION

As displayed in FIG.9 a confirmation button must be pressed.

Press EXIT to abort the operation.

Page 13 of 20

s o l a r iu d i


14/20


2.3.2 GROUP TIMES

FIG.10 : GROUP TIMES

Pressing GROUP TIMES button the form printed in FIG.10 will be displayed.

After the selection of the GROUP (using the combo box GROUP NAME) the time-rules fieldswill be displayed.

For the meaning of each field refer to the table in section 2.3.1.

Pressing ASSIGN THE DISPLAYED TIME RULES TO ALL TFT DEVICES BELONGING TO THE SELECTEDGROUP button is possible to assign, automatically, the defined time rules to all devices relatedto the selected group.

As displayed in FIG.9 a confirmation button must be pressed.

Pressing EXIT button the operation will be aborted.

Page 14 of 20

s o l a r iu d i


15/20


2.3.3 DEVICE TIMES

FIG.11 : DEVICE TIMES

Pressing DEVICE TIMES button the form printed in FIG.11 will be displayed.

After the selection of the DEVICE (using the combo box DEVICE NAME) the time-rules fieldswill be displayed.

For the meaning of each field refer to the table in section 2.3.1.

Pressing CONFIRM button is possible to assign the defined time rules to the selected

devices, overwriting (only for that device) global or group definitions (if present).


Page 15 of 20

s o l a r iu d i


16/20


2.4 LOAD NEW CONFIGURATION

FIG.12 : LOAD NEW CONFIGURATION FORM

Pressing LOAD NEW CONFIGURATION button the form printed in FIG.12 will bedisplayed.

As shown in the alarm box message this procedure can be very dangerous, because willdelete all the device time-rules previously defined and all the relationship between device andgroup.

All groups, global time definition and group time definition WILL NOT BE DELETED.

Pressing PROCEED button the form displayed in FIG.13 will be displayed.


Page 16 of 20

s o l a r iu d i


17/20


FIG.13 : AFTER LOAD NEW CONFIGURATION

For all the devices the fields:

- CHECK IF TFT- GROUP- SWITCH OFF- SWITCH ON- WEEKLY FREQUENCY- ENA / DIS

have been deleted.

Remember! This function must be used:

- the 1sttime (after the installation)

- in case of heavy modification of the system devices configuration (adding orremoving a lot of TFT devices).

If in the peripheral system configuration the number of TFT devices is greater than thenumber of other devices the button CHECK ALL AS TFT can be helpful.

Page 17 of 20

s o l a r iu d i


18/20


FIG.14 : AFTER CHECK ALL AS TFT

As displayed in FIG. 14 all devices have been checked as TFT.

Now all different devices (not TFT) can be de-selected.

Remember!

SAVE button must be pressed to save the configuration !!!

Page 18 of 20

s o l a r iu d i


19/20


2.5 EMERGENCY

FIG.15 : EMERGENCY FORM

Pressing EMERGENCY button the form printed in FIG.15 will be displayed.

This function, useful in case of emergency conditions, handles the 3 following possibilities:

2.5.1 - Force immediate switch on for all TFT devices (and disable time rules)

Send to all devices checked as TFT the command in order to SWITCH ON IMMEDIATELYthe lamps.

The switch on-off time rules defined for each device will be disabled.

2.5.2 - Re-enable time rules

Stop the emergency action and re-enable, for each TFT device, the related time-rules.

2.5.3 - Re-start server application (*)

Force a restart of the server application tfthan.

Page 19 of 20

s o l a r iu d i


20/20


Pressing PROCEED button the selected operation will be performed, while pressing EXITbutton the selected operation will be aborted.

(*) After pressing PROCEED button wait some seconds before to see de return message.

Page 20 of 20

s o l a r iu d i

Date post:	03-Apr-2018
Category:	Documents
Upload:	oicfbd
View:	224 times
Download:	0 times

c07a10 Tft Management User Manual

Documents