TWIST FOOT EMPEROR TREFOIL

DATA SHEET

• BASE FIXING KIT DESIGNED FOR FAST INSTALL ON 41X41 AND 41X21 UNISTRUT CHANNEL/LADDER

• CLEAT COMES WITH ALL FIXINGS IN PLACE READY FOR INSTALL, NO EXTRA FIXINGS ARE REQUIRED ON SITE

• FIXING KIT CAN BE SUPPLIED IN A4 STAINLESS STEEL, GALVANISED STEEL OR ZINC PLATED STEEL

• SHORT CIRCUIT AND MECHANICALLY TESTED TO IEC 61914 - REFER TO EMPEROR TREFOIL DATA SHEET

PART NO.CABLE RANGE DIMENSIONS (mm)

WEIGHT (g)MIN Ø

(mm)MAX Ø (mm)

W H D

ER19-23TFM12-X 19 23 96 86 54 475

ER23-28TFM12-X 23 28 96 86 54 475

ER27-32TFM12-X 27 32 97 91 54 490

ER30-35TFM12-X 30 35 99 94 54 495

ER33-38TFM12-X 33 38 103 98 54 510

ER36-42TFM12-X 36 42 124 103 54 660

ER40-46TFM12-X 40 46 125 109 54 655

ER44-50TFM12-X 44 50 130 120 54 680

ER48-55TFM12-X 48 55 132 124 54 690

ER51-58TFM12-X 51 58 136 131 54 700

ER55-62TTFM10-X 55 62 160 138 70 810

ER59-66TTFM10-X 59 66 163 146 70 825

ER63-70TTFM10-X 63 70 166 154 70 950

ER67-74TTFM10-X 67 74 169 161 70 950

ER71-78TTFM10-X 71 78 172 168 70 990

ER74-82TTFM10-X 74 82 177 174 70 990

ER77-85TTFM10-X 77 85 183 180 70 1005

ER82-88TTFM10-X 82 88 191 190 70 920

ER88-96TTFM10-X 88 96 207 206 70 990

ER96-103TTFM10-X 96 103 221 221 70 1040

ER103-111TTFM10-X 103 111 237 238 70 1050

ER111-119TTFM10-X 111 119 253 253 70 1110

ER119-128TTFM10-X 119 128 265 278 70 1320

www.ellispatents.co.uk

ELLIS PATENTS LTD.

1 / 2

ISSUE 01 21/08/19

DS39E

SINGLE FIX TWIST FOOT: ER19-23 TO ER51-58

TWIN FIX TWIST FOOT: ER55-62 TO ER119-128

X DENOTES FIXING MATERIAL, OPTIONS ARE AS FOLLOWS:

4 = A4 STAINLESS STEELG = GALVANISED STEELZ = ZINC PLATED STEEL

E.G A ER33-38 WITH STAINLESS STEEL TWIST FOOT FIXINGS BECOMES: ER33-38TFM10-4

EMPEROR TREFOIL TWIST FOOT OPTIONS

Patent App No. UK 1620469.5

www.ellispatents.co.uk

ELLIS PATENTS LTD.

This data sheet is subject to change without notice. The information provided has been generated in laboratory conditions, as such results in use may vary.

ISSUE 01 21/08/19

2 / 2

TWIST FOOT EMPEROR TREFOIL

DATA SHEETDS39E

1) Lower the cleat through the gap in the channel.

2) Once lowered twist the cleat 90°.

3) Tighten the M10 bolt in the base of the cleat.

4) As the bolt is tightened the channel nut will move up the twist foot base and grip onto the channel.

5) The cleat is now securely fastened to the structure and is ready to accept the cables.

1) Lower the cleat through the gap in the channel.

2) Rotate both twist foot bases through 90° into the locking position.

3) Tighten both bolts in the base of the cleat to the same torque value.

4) As the bolts are tightened the channel nuts will move up the twist foot base and grip onto the channel.

5) The cleat is now securely fastened to the structure and is ready to accept the cables.

INSTALLATION OVERVIEWSINGLE FIX TWIST FOOT: ER19-23 TO ER51-58

TWIN FIX TWIST FOOT: ER55-62 TO ER119-128