28
Cable ladder Divider Fittings Covers Accessoires UL Cable ladder systems available in height 53 80 100 150 72 CABLE TRAY SYSTEM GFK
Cable ladder
Divider
Fittings
Covers
Accessoires
ULULULULCable ladder systems available in height 53 80 100 150
ULSystemSystem
ULULULULUL72
CABLE TRAY SYSTEM GFK
To support important quantities of cables with large diameter, EBO Systems propose the cable ladder in Glass
Reinforced polyester GRP, with a support distance of up 6 m. The EBO Systems cable ladder allows to meet
the needs in the industry such as nuclear and thermal power plants but also in the oil and gas industry.
The unique patented clip-in rungs assembly, without metallic or thermoplastic parts who weak the cables ladders,
the cable ladder EBO Systems is the only one 100% GRP and could be easly assembled close to customers.
73
GRP-Cable Ladder, pultruded UL 76 80 84 89
GRP-Endcap, pressed ULKE 76 80 84 89
GRP-Splice plate, horizontal ULGH 76 80 85 90
Stainless steel-Splice plate, horizontal ULIH 77 81 85 90
GRP-Divider, pressed ULTL 77 81 85 90
GRP-T-, pultruded ULTE 77 81 85 90
GRP-Cross, pultruded ULX 77 81 86 91
GRP-Elbow 90°, pultruded ULB 78 82 86 91
GRP-Elbow, pultruded, vertical ULBA 78 82 87 92
GRP-Reducers, pultruded ULRU 78 82 87 92
GRP-Splice plate, pressed, vertical ULGV 79 83 87 92
Stainless steel-Splice plate, vertical ULIV 79 83 88 93
Cover clips DF 96
Vertical clamp ULKV 96
Cover fi x DFUB 97*
Cover clamp DFW 97
GRP-Hold down clamp ULKG 98* Hold down clamp ULKH 98*
Bolt BKM 98*
Dome head bolt FKM 98*
Hexagon head bolt SKM 98*
Cover fi xing insert DF M 99*
Vertical clamp WWU 99*
Fork-type self-locking plier ULP 99*
Covers for cables ladders UL systems are available from page 94.
SYSTEM
ACCESSORIES
Available siderail heights 53 80 100 150
53
53
53
53
53
53
53
53
53
53
53
53
80
80
80
100
80
80
80
80
80
80
80
80
80
100
100
150
150
150
100 150
100 150
100 150
100 150
100 150
100 150
100 150
100 150
100 150
* suitable for all heights
NEW
74
CABLE LADDER SYSTEM UL
UL...
ULKE...
ULRU...
ULB...
ULBA...
KKD...
ULTE...
ULBA...
ULX...
75
76
CABLE LADDER SYSTEM UL
GRP cable ladderspultruded, not perforated rungs
L = fixing distance (m)
Load
q (k
N/m
)
Warning : the deflection is measured with a junction position between 2 cable trays at a distance L/5 from thesupport. If this distance is not respected, it is necessary to raise the deflection values by approx. 30%.
The cables ladders have the advantage to be 100% GRP (Glass Reinforced Polyester ), thanksto unique patented clip-in rungs assembly, without metallic or thermoplastic parts.The cables ladders are delivered with non perforated rungs. However the option of perforatedrungs is still possible, please contact us.
Load diagram : q = load evenly distributed cables (according to DIN EN IEC 61537 standard)
UL 53.150/3
7032 53 150 4 6,5 x 20UL 53.200/3 7032 53 200 4 6,5 x 20UL 53.300/3 7032 53 300 4 6,5 x 20UL 53.400/3 7032 53 400 4 6,5 x 20UL 53.500/3 7032 53 500 4 6,5 x 20UL 53.600/3 7032 53 600 4 6,5 x 20UL 53.200 7032 53 200 4 6,5 x 20UL 53.300 7032 53 300 4 6,5 x 20UL 53.400 7032 53 400 4 6,5 x 20UL 53.500 7032 53 500 4 6,5 x 20UL 53.600 7032 53 600 4 6,5 x 20
K23
K23K23K23K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
Materialthickness
(th)
Side perforations
mm mm mm mm
Min. pack.
3 m3 m3 m3 m3 m3 m6 m6 m6 m6 m6 m
EANcode
957958957972957996958016958030958054957965957989958009958023958047
Weight 100 units
m
108,7116,0131,0145,0160,0175,0116,0131,0145,0160,0175,0
End cap for GRP cable ladderpultruded
Used for: Cable ladders UL…H53 L3 and UL…H53 L6
Mounting accessories required : 2 bolts M6x16 V4A ( to be ordered separately )
ULKE 53.150
7032 53 150ULKE 53.200 7032 53 200ULKE 53.300 7032 53 300ULKE 53.400 7032 53 400ULKE 53.500 7032 53 500ULKE 53.600 7032 53 600
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
965748965755965762965779965786965793
Weight 100 units
pc
5,67,09,8
12,615,418,2
GRP horizontal splice platepressed, horizontal
Need: 2 pieces for each cut, to be ordered separatly
for connecting cable ladders and fittings H…, with splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULGH 53
7032 45 190K23
Item ref. RAL colour
Height LengthL
mm mm
Min. pack.
1 set
EANcode
960156
Weight 100 units
8,5
When fixing the splice plates ULIH… and ULGH..., an expansion distance of about 3 mm must beconsidered.
77
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H53
ULIH 53 E4
45 Ø 8 20x8E4
Item ref. Height perforation For oblong perforations LL
mm mm mm
Min. pack.
1 set
EANcode
960194
Weight 100 units
6,1
Mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 53
7032 30K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958511
Weight 100 units
m
60
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULTE 53.150
7032 53 150ULTE 53.200 7032 53 200ULTE 53.300 7032 53 300ULTE 53.400 7032 53 400ULTE 53.500 7032 53 500ULTE 53.600 7032 53 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959235959242959259959266959273959280
Weight 100 units
pc
550590620720760830
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULX 53.150
7032 53 150 —ULX 53.200 7032 53 200 —ULX 53.300 7032 53 300 —ULX 53.400 7032 53 400 —ULX 53.500 7032 53 500 —ULX 53.600 7032 53 600 —
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
B+D
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959570959587959594959600959617959624
Weight 100 units
pc
687,5738,0775,0900,0950,0
1.050,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
77
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H53
ULIH 53 E4
45 Ø 8 20x8E4
Item ref. Height perforation For oblong perforations LL
mm mm mm
Min. pack.
1 set
EANcode
960194
Weight 100 units
6,1
Mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 53
7032 30K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958511
Weight 100 units
m
60
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULTE 53.150
7032 53 150ULTE 53.200 7032 53 200ULTE 53.300 7032 53 300ULTE 53.400 7032 53 400ULTE 53.500 7032 53 500ULTE 53.600 7032 53 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959235959242959259959266959273959280
Weight 100 units
pc
550590620720760830
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULX 53.150
7032 53 150 —ULX 53.200 7032 53 200 —ULX 53.300 7032 53 300 —ULX 53.400 7032 53 400 —ULX 53.500 7032 53 500 —ULX 53.600 7032 53 600 —
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
B+D
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959570959587959594959600959617959624
Weight 100 units
pc
687,5738,0775,0900,0950,0
1.050,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
77
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H53
ULIH 53 E4
45 Ø 8 20x8E4
Item ref. Height perforation For oblong perforations LL
mm mm mm
Min. pack.
1 set
EANcode
960194
Weight 100 units
6,1
Mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 53
7032 30K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958511
Weight 100 units
m
60
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULTE 53.150
7032 53 150ULTE 53.200 7032 53 200ULTE 53.300 7032 53 300ULTE 53.400 7032 53 400ULTE 53.500 7032 53 500ULTE 53.600 7032 53 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959235959242959259959266959273959280
Weight 100 units
pc
550590620720760830
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULX 53.150
7032 53 150 —ULX 53.200 7032 53 200 —ULX 53.300 7032 53 300 —ULX 53.400 7032 53 400 —ULX 53.500 7032 53 500 —ULX 53.600 7032 53 600 —
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
B+D
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959570959587959594959600959617959624
Weight 100 units
pc
687,5738,0775,0900,0950,0
1.050,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
77
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H53
ULIH 53 E4
45 Ø 8 20x8E4
Item ref. Height perforation For oblong perforations LL
mm mm mm
Min. pack.
1 set
EANcode
960194
Weight 100 units
6,1
Mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 53
7032 30K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958511
Weight 100 units
m
60
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULTE 53.150
7032 53 150ULTE 53.200 7032 53 200ULTE 53.300 7032 53 300ULTE 53.400 7032 53 400ULTE 53.500 7032 53 500ULTE 53.600 7032 53 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959235959242959259959266959273959280
Weight 100 units
pc
550590620720760830
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULX 53.150
7032 53 150 —ULX 53.200 7032 53 200 —ULX 53.300 7032 53 300 —ULX 53.400 7032 53 400 —ULX 53.500 7032 53 500 —ULX 53.600 7032 53 600 —
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
B+D
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959570959587959594959600959617959624
Weight 100 units
pc
687,5738,0775,0900,0950,0
1.050,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
78
CABLE LADDER SYSTEM UL
GRP elbow 90°pultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
Available in radius 250 mm
ULB 53.150
7032 53 150ULB 53.200 7032 53 200ULB 53.300 7032 53 300ULB 53.400 7032 53 400ULB 53.500 7032 53 500ULB 53.600 7032 53 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
958559958566958573958580958597958603
Weight 100 units
pc
160180200270310350
During the installation, you must take care to position a support under the elbow at each cable ladderend. If the bending radius is higher than 250 mm and if the width of cable ladder is higher than 400 mm, anadditional intermediary support is then necessary. The metallic splice plates must be fixed at each cable ladder end with 4 bolts M 6x20 V4A (to beordered separately).
GRP adjustable elbowpultruded, with integrated splice plates, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
ULBA 53.150
7032 53 150ULBA 53.200 7032 53 200ULBA 53.300 7032 53 300ULBA 53.400 7032 53 400ULBA 53.500 7032 53 500ULBA 53.600 7032 53 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
958894958900958917958924958931958948
Weight 100 units
pc
8082869195
100
In order to guarantee a conform assembly, the metallic splice plates must be fixed at each cableladder end with 4 bolts M 6 x16 V4A and the composite splice plates must be fixed at each cableladder end with 4 bolts M 6 x 20 V4A (to be ordered separatelyIf the bending radius is higher than 250 mm and if the width of cable ladder is higher than 400 mm, anadditional intermediary support is then necessary.
Reducerpultruded
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering. The dimensions B1 and B2 allow to define the reduction size to use
to reduce or increase the cables ladder width
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULRU 53.100
7032 53 100ULRU 53.150 7032 53 150ULRU 53.200 7032 53 200ULRU 53.300 7032 53 300ULRU 53.400 7032 53 400
E4 K23
E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
959914959921959938959945959952
Weight 100 units
pc
3337435064
When mounting, the reducer must be supported by a bracket. The dimension B corresponds to thereduction. To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
79
GRP vertical adjustable or vertical fixed angle splice platepressed, vertical
Need: 2 pieces for each cut, to be ordered separatly
for connecting cable ladders and fittings H80, with adjustable or fixed splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULGV 53
7032 45K23
Item ref. RAL colour
Height
mm
Min. pack.
1 set
EANcode
960231
Weight 100 units
27,5
Vertical splice platevertical, stainless steel
Need: 2 pieces for each cut, to be ordered separatly
for connecting cable ladders and fittings H53, with adjustable splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULIV 53 E4
45E4
Item ref. Height
mm
Min. pack.
1 set
EANcode
960279
Weight 100 units
30
80
CABLE LADDER SYSTEM UL
GRP cable ladderspultruded, not perforated rungs
L = fixing distance (m)
Load
q (k
N/m
)
Warning : the deflection is measured with a junction position between 2 cable trays at a distance L/5 from thesupport. If this distance is not respected, it is necessary to raise the deflection values by approx. 30%.
The cables ladders have the advantage to be 100% GRP (Glass Reinforced Polyester ), thanksto unique patented clip-in rungs assembly, without metallic or thermoplastic parts.The cables ladders are delivered with non perforated rungs. However the option of perforatedrungs is still possible, please contact us.
Load diagram : q = load evenly distributed cables (according to DIN EN IEC 61537 standard)
UL 80.150/3
7032 80 150 4UL 80.200/3 7032 80 200 4UL 80.300/3 7032 80 300 4UL 80.400/3 7032 80 400 4UL 80.500/3 7032 80 500 4UL 80.600/3 7032 80 600 4UL 80.150 7032 80 150 4UL 80.200 7032 80 200 4UL 80.300 7032 80 300 4UL 80.400 7032 80 400 4UL 80.500 7032 80 500 4UL 80.600 7032 80 600 4
K23
K23K23K23K23K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
Materialthickness
(th)mm mm mm
Min. pack.
3 m3 m3 m3 m3 m3 m6 m6 m6 m6 m6 m6 m
EANcode
958078958092958115958139958153958177958061958085958108958122958146958160
Weight 100 units
m
223230245260275290223230245260275290
End cap for GRP cable ladderpultruded
Used for: Cable ladders UL…H80 L3 and UL…H80 L6
Mounting accessories required : 2 bolts M6x16 V4A ( to be ordered separately )
ULKE 80.150
7032 80 150ULKE 80.200 7032 80 200ULKE 80.300 7032 80 300ULKE 80.400 7032 80 400ULKE 80.500 7032 80 500ULKE 80.600 7032 80 600
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
965809965816965823965830965847965854
Weight 100 units
pc
8,510,614,819,123,327,6
GRP horizontal splice platepressed, horizontal
for connecting cable ladders and fittings H…, with splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULGH 80
7032 72 200K23
Item ref. RAL colour
Height LengthL
mm mm
Min. pack.
1 set
EANcode
960163
Weight 100 units
10
When fixing the splice plates ULIH… and ULGH..., an expansion distance of about 3 mm must beconsidered.
81
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H80
ULIH 80 E4
72 20x8 Ø 8E4
Item ref. Height For oblong perforations LL
perforation
mm mm mm
Min. pack.
1 set
EANcode
960200
Weight 100 units
6,1
mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 80
7032 57K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958528
Weight 100 units
m
60
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 80/ ULIH 80 V4A are not included in the cables ladders, please order themseparately.
ULTE 80.150
7032 80 150ULTE 80.200 7032 80 200ULTE 80.300 7032 80 300ULTE 80.400 7032 80 400ULTE 80.500 7032 80 500ULTE 80.600 7032 80 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959297959303959310959327959334959341
Weight 100 units
pc
550590653720780850
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 80/ ULIH 80 V4A are not included in the cables ladders, please order themseparately.
ULX 80.150
7032 80 150ULX 80.200 7032 80 200ULX 80.300 7032 80 300ULX 80.400 7032 80 400ULX 80.500 7032 80 500ULX 80.600 7032 80 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959631959648959655959662959679959686
Weight 100 units
pc
687,5738,0816,0900,0975,0820,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mm
77
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H53
ULIH 53 E4
45 Ø 8 20x8E4
Item ref. Height perforation For oblong perforations LL
mm mm mm
Min. pack.
1 set
EANcode
960194
Weight 100 units
6,1
Mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 53
7032 30K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958511
Weight 100 units
m
60
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULTE 53.150
7032 53 150ULTE 53.200 7032 53 200ULTE 53.300 7032 53 300ULTE 53.400 7032 53 400ULTE 53.500 7032 53 500ULTE 53.600 7032 53 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959235959242959259959266959273959280
Weight 100 units
pc
550590620720760830
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULX 53.150
7032 53 150 —ULX 53.200 7032 53 200 —ULX 53.300 7032 53 300 —ULX 53.400 7032 53 400 —ULX 53.500 7032 53 500 —ULX 53.600 7032 53 600 —
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
B+D
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959570959587959594959600959617959624
Weight 100 units
pc
687,5738,0775,0900,0950,0
1.050,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
77
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H53
ULIH 53 E4
45 Ø 8 20x8E4
Item ref. Height perforation For oblong perforations LL
mm mm mm
Min. pack.
1 set
EANcode
960194
Weight 100 units
6,1
Mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 53
7032 30K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958511
Weight 100 units
m
60
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULTE 53.150
7032 53 150ULTE 53.200 7032 53 200ULTE 53.300 7032 53 300ULTE 53.400 7032 53 400ULTE 53.500 7032 53 500ULTE 53.600 7032 53 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959235959242959259959266959273959280
Weight 100 units
pc
550590620720760830
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULX 53.150
7032 53 150 —ULX 53.200 7032 53 200 —ULX 53.300 7032 53 300 —ULX 53.400 7032 53 400 —ULX 53.500 7032 53 500 —ULX 53.600 7032 53 600 —
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
B+D
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959570959587959594959600959617959624
Weight 100 units
pc
687,5738,0775,0900,0950,0
1.050,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
77
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H53
ULIH 53 E4
45 Ø 8 20x8E4
Item ref. Height perforation For oblong perforations LL
mm mm mm
Min. pack.
1 set
EANcode
960194
Weight 100 units
6,1
Mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 53
7032 30K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958511
Weight 100 units
m
60
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULTE 53.150
7032 53 150ULTE 53.200 7032 53 200ULTE 53.300 7032 53 300ULTE 53.400 7032 53 400ULTE 53.500 7032 53 500ULTE 53.600 7032 53 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959235959242959259959266959273959280
Weight 100 units
pc
550590620720760830
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULX 53.150
7032 53 150 —ULX 53.200 7032 53 200 —ULX 53.300 7032 53 300 —ULX 53.400 7032 53 400 —ULX 53.500 7032 53 500 —ULX 53.600 7032 53 600 —
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
B+D
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959570959587959594959600959617959624
Weight 100 units
pc
687,5738,0775,0900,0950,0
1.050,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
82
CABLE LADDER SYSTEM UL
GRP elbow 90°pultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 80/ ULIH 80 V4A are not included in the cables ladders, please order themseparately.
ULB 80.150
7032 80 150ULB 80.200 7032 80 200ULB 80.300 7032 80 300ULB 80.400 7032 80 400ULB 80.500 7032 80 500ULB 80.600 7032 80 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
958610958627958634958641958658958665
Weight 100 units
pc
220240270360400440
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP adjustable elbowpultruded, with integrated splice plates, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
ULBA 80.150
7032 80 150ULBA 80.200 7032 80 200ULBA 80.300 7032 80 300ULBA 80.400 7032 80 400ULBA 80.500 7032 80 500ULBA 80.600 7032 80 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
958955958962958979958986958993959006
Weight 100 units
pc
130136144150155161
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
Reducerpultruded
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering. The dimensions B1 and B2 allow to define the reduction size to use
to reduce or increase the cables ladder width
The splice plates ULGH 80/ ULIH 80 V4A are not included in the cables ladders, please order themseparately.
ULRU 80.100
7032 80 100ULRU 80.150 7032 80 150ULRU 80.200 7032 80 200ULRU 80.300 7032 80 300ULRU 80.400 7032 80 400
E4 K23
E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
959969959976959983959990960002
Weight 100 units
pc
4246516371
When mounting, the reducer must be supported by a bracket. The dimension B corresponds to thereduction. To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
83
GRP vertical adjustable or vertical fixed angle splice platepressed, vertical
Need: 2 pieces for each cut, to be ordered separatly
for connecting cable ladders and fittings H80, with adjustable or fixed splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULGV 80
7032 72K23
Item ref. RAL colour
Height
mm
Min. pack.
1 set
EANcode
960248
Weight 100 units
27,5
Vertical splice platevertical, stainless steel
Need: 2 pieces for each cut, to be ordered separatly
for connecting cable ladders and fittings H80, with adjustable splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULIV 80 E4
72E4
Item ref. Height
mm
Min. pack.
1 set
EANcode
960286
Weight 100 units
30
84
CABLE LADDER SYSTEM UL
GRP cable ladderspultruded, not perforated rungs
L = fixing distance (m)
Load
q (k
N/m
)
Warning : the deflection is measured with a junction position between 2 cable trays at a distance L/5 from thesupport. If this distance is not respected, it is necessary to raise the deflection values by approx. 30%.
The cables ladders have the advantage to be 100% GRP (Glass Reinforced Polyester ), thanksto unique patented clip-in rungs assembly, without metallic or thermoplastic parts.The cables ladders are delivered with non perforated rungs. However the option of perforatedrungs is still possible, please contact us.
Load diagram : q = load evenly distributed cables (according to DIN EN IEC 61537 standard)
UL 100.150/3
7032 100 150 5UL 100.200/3 7032 100 200 5UL 100.300/3 7032 100 300 5UL 100.400/3 7032 100 400 5UL 100.450/3 7032 100 450 5UL 100.500/3 7032 100 500 5UL 100.600/3 7032 100 600 5UL 100.750/3 7032 100 750 5UL 100.900/3 7032 100 900 5UL 100.150 7032 100 150 5UL 100.200 7032 100 200 5UL 100.300 7032 100 300 5UL 100.400 7032 100 400 5UL 100.450 7032 100 450 5UL 100.500 7032 100 500 5UL 100.600 7032 100 600 5UL 100.750 7032 100 750 5UL 100.900 7032 100 900 5
K23
K23K23K23K23K23K23K23K23K23K23K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
Materialthickness
(th)mm mm mm
Min. pack.
3 m3 m3 m3 m3 m3 m3 m3 m3 m6 m6 m6 m6 m6 m6 m6 m6 m6 m
EANcode
958191958214958238958252958276958290958313958351958399958184958207958221958245958269958283958306958344958382
Weight 100 units
m
312,3320,8338,6356,3362,0375,0392,5413,5445,1312,3320,8338,6356,3362,0375,0392,5413,5445,1
End cap for GRP cable ladderpultruded
Used for: Cable ladders UL…H100 L3 and UL…H100 L6
Mounting accessories required : 2 bolts M6x16 V4A ( to be ordered separately )
ULKE 100.150
7032 100 150ULKE 100.200 7032 100 200ULKE 100.300 7032 100 300ULKE 100.400 7032 100 400ULKE 100.450 7032 100 450ULKE 100.500 7032 100 500ULKE 100.600 7032 100 600ULKE 100.700 7032 100 700ULKE 100.750 7032 100 750ULKE 100.800 7032 100 800ULKE 100.900 7032 100 900
K23
K23K23K23K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
965526965533965540965557965564965571965588965595965601965618965625
Weight 100 units
pc
1620273542454957606470
85
GRP horizontal splice platepressed, horizontal
for connecting cable ladders and fittings H…, with splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULGH 100
7032 90 200K23
Item ref. RAL colour
Height LengthL
mm mm
Min. pack.
1 set
EANcode
960170
Weight 100 units
3,5
When fixing the splice plates ULIH… and ULGH..., an expansion distance of about 3 mm must beconsidered.
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H100
ULIH 100 E4
90 Ø 8 20x8E4
Item ref. Height perforation For oblong perforations LL
mm mm mm
Min. pack.
1 set
EANcode
960217
Weight 100 units
19,5
mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 100
7032 65K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958535
Weight 100 units
pc
40
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 100/ ULIH 100 V4A are not included in the cables ladders, please order themseparately.
Available in radius 250 mm, 600 mm und 900 mm
ULTE 100.150
7032 100 150ULTE 100.200 7032 100 200ULTE 100.300 7032 100 300ULTE 100.400 7032 100 400ULTE 100.450 7032 100 450ULTE 100.500 7032 100 500ULTE 100.600 7032 100 600ULTE 100.750 7032 100 750ULTE 100.900 7032 100 900
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959358959365959372959389959396959402959419959433959457
Weight 100 units
pc
520550653720750780850950
1050
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
77
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H53
ULIH 53 E4
45 Ø 8 20x8E4
Item ref. Height perforation For oblong perforations LL
mm mm mm
Min. pack.
1 set
EANcode
960194
Weight 100 units
6,1
Mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 53
7032 30K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958511
Weight 100 units
m
60
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULTE 53.150
7032 53 150ULTE 53.200 7032 53 200ULTE 53.300 7032 53 300ULTE 53.400 7032 53 400ULTE 53.500 7032 53 500ULTE 53.600 7032 53 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959235959242959259959266959273959280
Weight 100 units
pc
550590620720760830
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULX 53.150
7032 53 150 —ULX 53.200 7032 53 200 —ULX 53.300 7032 53 300 —ULX 53.400 7032 53 400 —ULX 53.500 7032 53 500 —ULX 53.600 7032 53 600 —
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
B+D
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959570959587959594959600959617959624
Weight 100 units
pc
687,5738,0775,0900,0950,0
1.050,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
86
CABLE LADDER SYSTEM UL
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 100/ ULIH 100 V4A are not included in the cables ladders, please order themseparately.
Available in radius 250 mm, 600 mm und 900 mm
ULX 100.150
7032 100 150ULX 100.200 7032 100 200ULX 100.300 7032 100 300ULX 100.400 7032 100 400ULX 100.450 7032 100 450ULX 100.500 7032 100 500ULX 100.600 7032 100 600ULX 100.750 7032 100 750ULX 100.900 7032 100 900
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959693959709959716959723959730959747959754959778959792
Weight 100 units
pc
710750816900940975
107011801300
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP elbow 90°pultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 100/ ULIH 100 V4A are not included in the cables ladders, please order themseparately.
Available in radius 250 mm, 600 mm und 900 mm
ULB 100.150
7032 100 150ULB 100.200 7032 100 200ULB 100.300 7032 100 300ULB 100.400 7032 100 400ULB 100.450 7032 100 450ULB 100.500 7032 100 500ULB 100.600 7032 100 600ULB 100.750 7032 100 750ULB 100.900 7032 100 900
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
958672958689958696958702958719958726958733958757958771
Weight 100 units
pc m/
320340388470490520570648720
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
87
GRP adjustable elbowpultruded, with integrated splice plates, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
Available in radius around 600 mm & 900 mm.
ULBA 100.150
7032 100 150ULBA 100.200 7032 100 200ULBA 100.300 7032 100 300ULBA 100.400 7032 100 400ULBA 100.450 7032 100 450ULBA 100.500 7032 100 500ULBA 100.600 7032 100 600ULBA 100.750 7032 100 750ULBA 100.900 7032 100 900
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959013959020959037959044959051959068959075959099959112
Weight 100 units
pc
220212217223226228234242251
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
Reducerpultruded
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering. The dimensions B1 and B2 allow to define the reduction size to use
to reduce or increase the cables ladder width
The splice plates ULGH 100/ ULIH 100 V4A are not included in the cables ladders, please order themseparately.
ULRU 100.100
7032 100 100ULRU 100.150 7032 100 150ULRU 100.200 7032 100 200ULRU 100.300 7032 100 300ULRU 100.400 7032 100 400ULRU 100.500 7032 100 500ULRU 100.600 7032 100 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
960019960026960033960040960057960064960071
Weight 100 units
pc
5155657895
109117
When mounting, the reducer must be supported by a bracket. The dimension B corresponds to thereduction. To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP vertical adjustable or with fixed angle splice platepressed, vertical
Need: 2 pieces for each cut, to be ordered separatly
for connecting cable ladders and fittings H80, with adjustable or fixed splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULGV 100
7032 100K23
Item ref. RAL colour
Height
mm
Min. pack.
1 set
EANcode
960255
Weight 100 units
27,5
88
CABLE LADDER SYSTEM UL
Vertical splice plateStainless steel, vertical
Need: 2 pieces for each cut, to be ordered separatly
for connecting cable ladders and fittings H100, with adjustable splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULIV 100 E4
90E5
Item ref. Height
mm
Min. pack.
1 set
EANcode
960293
Weight 100 units
30
89
GRP cable ladderspultruded
L = fixing distance (m)
Load
q (k
N/m
)
Warning : the deflection is measured with a junction position between 2 cable trays at a distance L/5 from thesupport. If this distance is not respected, it is necessary to raise the deflection values by approx. 30%.
The cables ladders have the advantage to be 100% GRP (Glass Reinforced Polyester ), thanksto unique patented clip-in rungs assembly, without metallic or thermoplastic parts.The cables ladders are delivered with non perforated rungs. However the option of perforatedrungs is still possible, please contact us.
Load diagram : q = load evenly distributed cables (according to DIN EN IEC 61537 standard)
UL 150.150/3
7032 150 150 6UL 150.200/3 7032 150 200 6UL 150.300/3 7032 150 300 6UL 150.400/3 7032 150 400 6UL 150.450/3 7032 150 450 6UL 150.500/3 7032 150 500 6UL 150.600/3 7032 150 600 6UL 150.750/3 7032 150 750 6UL 150.900/3 7032 150 900 6UL 150.150 7032 150 150 6UL 150.200 7032 150 200 6UL 150.300 7032 150 300 6UL 150.400 7032 150 400 6UL 150.450 7032 150 450 6UL 150.500 7032 150 500 6UL 150.600 7032 150 600 6UL 150.750 7032 150 750 6UL 150.900 7032 150 900 6
K23
K23K23K23K23K23K23K23K23K23K23K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
Materialthickness
(th)mm mm mm
Min. pack.
3 m3 m3 m3 m3 m3 m3 m3 m3 m6 m6 m6 m6 m6 m6 m6 m6 m6 m
EANcode
965168965175965182965199965205965212965229965243965267958405958412958429958436958443958450958467958481958504
Weight 100 units
m
553,5570,3603,3636,8653,6670,3660,0754,1804,3553,5570,3603,3636,8653,6670,3660,0754,1804,3
End cap for GRP cable ladderpultruded
Used for: Cable ladders UL…H150 L3 and UL…H150 L6
Mounting accessories required : 2 bolts M6x16 V4A ( to be ordered separately )
ULKE 150.150
7032 150 150ULKE 150.200 7032 150 200ULKE 150.300 7032 150 300ULKE 150.400 7032 150 400ULKE 150.450 7032 150 450ULKE 150.500 7032 150 500ULKE 150.600 7032 150 600ULKE 150.750 7032 150 750ULKE 150.900 7032 150 900
K23
K23K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
965632965649965656965663965670965687965694965717965731
Weight 100 units
pc
16,420,428,436,340,344,352,264,276,1
90
CABLE LADDER SYSTEM UL
GRP horizontal splice platepressed, horizontal
for connecting cable ladders and fittings H…, with splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULGH 150
7032 138 250K23
Item ref. RAL colour
Height LengthL
mm mm
Min. pack.
1 set
EANcode
960187
Weight 100 units
pc
38
When fixing the splice plates ULIH… and ULGH..., an expansion distance of about 3 mm must beconsidered.
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H150
ULIH 150 E4
138 Ø 8 20x8E4
Item ref. Height perforation For oblong perforations LL
mm mm mm
Min. pack.
1 set
EANcode
960224
Weight 100 units
27
mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 150
7032 102K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958542
Weight 100 units
m
80
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 150/ ULIH 150 V4A are not included in the cables ladders, please order themseparately.
Available in radius 250 mm, 600 mm und 900 mm
ULTE 150.150
7032 150 150ULTE 150.200 7032 150 200ULTE 150.300 7032 150 300ULTE 150.400 7032 150 400ULTE 150.450 7032 150 450ULTE 150.500 7032 150 500ULTE 150.600 7032 150 600ULTE 150.750 7032 150 750ULTE 150.900 7032 150 900
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959464959471959488959495959501959518959525959549959563
Weight 100 units
pc
650800999
120013001200125016601910
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
77
Horizontal stainless steel splice platehorizontal
for horizontal changes of directions and for the connection of cable ladders and fittings H53
ULIH 53 E4
45 Ø 8 20x8E4
Item ref. Height perforation For oblong perforations LL
mm mm mm
Min. pack.
1 set
EANcode
960194
Weight 100 units
6,1
Mount cable ladders with a space of 3 mm minimumThe holes in the splice plates ensure a solid fixing and allow the GRP material expansion. During the assembly, please verify that the splice plates oblong holes are located on the same side asthe supporting bracket. To help fixing the stainless steel splice plates ULIH, we recommend to use afork-type self locking plier ULP.To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP separatorpressed
to separate cables with different functions and / or to separate voltages
ULTL 53
7032 30K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m
EANcode
958511
Weight 100 units
m
60
The GRP cover is fixed with self-tapping screws which are screwed in the ladder siderails and on thecover return flange or with rivets through the ladder siderails.
GRP tee junction cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULTE 53.150
7032 53 150ULTE 53.200 7032 53 200ULTE 53.300 7032 53 300ULTE 53.400 7032 53 400ULTE 53.500 7032 53 500ULTE 53.600 7032 53 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959235959242959259959266959273959280
Weight 100 units
pc
550590620720760830
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 53/ ULIH 53 V4A are not included in the cables ladders, please order themseparately.
ULX 53.150
7032 53 150 —ULX 53.200 7032 53 200 —ULX 53.300 7032 53 300 —ULX 53.400 7032 53 400 —ULX 53.500 7032 53 500 —ULX 53.600 7032 53 600 —
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
B+D
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959570959587959594959600959617959624
Weight 100 units
pc
687,5738,0775,0900,0950,0
1.050,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
91
GRP cross for cable ladderpultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 150/ ULIH 150 V4A are not included in the cables ladders, please order themseparately.
Available in radius 250 mm, 600 mm und 900 mm
ULX 150.150
7032 150 150ULX 150.200 7032 150 200ULX 150.300 7032 150 300ULX 150.400 7032 150 400ULX 150.450 7032 150 450ULX 150.500 7032 150 500ULX 150.600 7032 150 600ULX 150.750 7032 150 750ULX 150.900 7032 150 900
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959808959815959822959839959846959853959860959884959907
Weight 100 units
pc
812,51.000,01.247,01.540,01.650,01.500,01.900,02.110,02.830,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP elbow 90°pultruded, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
The splice plates ULGH 150/ ULIH 150 V4A are not included in the cables ladders, please order themseparately.
Available in radius 250 mm, 600 mm und 900 mm
ULB 150.150
7032 150 150ULB 150.200 7032 150 200ULB 150.300 7032 150 300ULB 150.400 7032 150 400ULB 150.450 7032 150 450ULB 150.500 7032 150 500ULB 150.600 7032 150 600ULB 150.750 7032 150 750ULB 150.900 7032 150 900
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
958788958795958801958818958825958832958849958863958887
Weight 100 units
pc
548,7584,4656,0830,0880,0930,0
1.050,01.068,01.087,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
92
CABLE LADDER SYSTEM UL
GRP adjustable elbowpultruded, with integrated splice plates, not perforated rungs
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering.
Available in radius around 600 mm & 900 mm.
ULBA 150.150
7032 150 150ULBA 150.200 7032 150 200ULBA 150.300 7032 150 300ULBA 150.400 7032 150 400ULBA 150.450 7032 150 450ULBA 150.500 7032 150 500ULBA 150.600 7032 150 600ULBA 150.750 7032 150 750ULBA 150.900 7032 150 900
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
959129959136959143959150959167959174959181959204959228
Weight 100 units
pc
400410420430435440450470480
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
Reducerpultruded
The fittings are delivered with non-perforated rungs. However the option with perforated rungsis still possible, please ask us. The siderails are made in pultruded GRP. The splices plates are available in GRP, or instainless steel, please specify the material when ordering. The dimensions B1 and B2 allow to define the reduction size to use
to reduce or increase the cables ladder width
The splice plates ULGH 150/ ULIH 150 V4A are not included in the cables ladders, please order themseparately.
ULRU 150.100
7032 150 100ULRU 150.150 7032 150 150ULRU 150.200 7032 150 200ULRU 150.300 7032 150 300ULRU 150.400 7032 150 400ULRU 150.500 7032 150 500ULRU 150.600 7032 150 600
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
960088960095960101960118960125960132960149
Weight 100 units
pc
77102102126153200200
When mounting, the reducer must be supported by a bracket. The dimension B corresponds to thereduction. To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
GRP vertical adjustable or vertical fixed angle splice platepressed, vertical
Need: 2 pieces for each cut, to be ordered separatly
for connecting cable ladders and fittings H80, with adjustable or fixed splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULGV 150
7032 138K23
Item ref. RAL colour
Height
mm
Min. pack.
1 set
EANcode
960262
Weight 100 units
27,5
93
Vertical splice platevertical, stainless steel
Need: 2 pieces for each cut, to be ordered separatly
for connecting cable ladders and fittings H150, with adjustable splice plates
To ensure a correct installation, the stainless steel splice plates must be fixed on each cable ladderend with 8 bolts M6x16V4A and the GRP splice plates must be fixed with 8 bolts M6x20V4A (must beordered separately)
ULIV 150 E4
138E4
Item ref. Height
mm
Min. pack.
1 set
EANcode
960309
Weight 100 units
30
94
CABLE LADDER SYSTEM COVERS UL
Cover for cable trays and cable ladderspressed
For a stronger assembly, the covers with a width above 400 mm are strengthened. Thesestrengthenings / ribs are visible on the outside face of the part.Used for: Cable tray H50, H80 and H110 mm, KK…, KKL… and cable ladder UL…H53, H80, H100
and H150 mm
KKD 50
7032 50KKD 100 7032 100KKD 150 7032 150KKD 200 7032 200KKD 250 7032 250KKD 300 7032 300KKD 400 7032 400KKD 450 7032 450KKD 500 7032 500KKD 600 7032 600KKD 750 7032 750KKD 900 7032 900
K23
K23K23K23K23K23K23K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
3 m3 m3 m3 m3 m3 m3 m3 m3 m3 m3 m
1,5 m
EANcode
956104956111956128956135956142956159956166956173956180956197956210956234
Weight 100 units
pc/
4778
105132152190243285292338438585
For a strong and compliant assembly, we recommend to leave a minimum distance of 8 mm betweenthe covers and the sidewalls of cable trays. Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
Cover for horizontal elbow 90°pressed
For a stronger assembly, the covers with a width above 400 mm are strengthened. Thesestrengthenings / ribs are visible on the outside face of the part.Used for: Horizontal elbow 90° H53, H80, H100 and H150, ULB…
Cover for elbow available in radius R250, R600 and R900 mm
ULBD 150
7032 150ULBD 200 7032 200ULBD 300 7032 300ULBD 400 7032 400ULBD 450 7032 450ULBD 500 7032 500ULBD 600 7032 600ULBD 750 7032 750ULBD 900 7032 900
K23
K23K23K23K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
957422957439957446957453957460957477957484957507957521
Weight 100 units
pc
115126210270330380490565683
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for vertical adjustable elbow
For a stronger assembly, the covers with a width above 400 mm are strengthened. Thesestrengthenings / ribs are visible on the outside face of the part.Used for: Vertical elbow 53 mm high, ULBA...
ULBAD 53.150
7032 150ULBAD 53.200 7032 200ULBAD 53.300 7032 300ULBAD 53.400 7032 400ULBAD 53.500 7032 500ULBAD 53.600 7032 600
K23
K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
059188059195059218059225059232059249
Weight 100 units
26,533,347,961,273,685,2
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, stormsfor example, the quantity of clips must be increased.
95
GRP cover for vertical adjustable elbowpressed
For a stronger assembly, the covers with a width above 400 mm are strengthened. Thesestrengthenings / ribs are visible on the outside face of the part.Used for: Vertical elbow 80 mm high, ULBA...
ULBAD 80.150
7032 150ULBAD 80.200 7032 200ULBAD 80.300 7032 300ULBAD 80.400 7032 400ULBAD 80.500 7032 500ULBAD 80.600 7032 600
K23
K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
059256059263059270059287059294059317
Weight 100 units
29,437,053,268,081,894,6
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, stormsfor example, the quantity of clips must be increased.
GRP cover for vertical adjustable elbowpressed
For a stronger assembly, the covers with a width above 400 mm are strengthened. Thesestrengthenings / ribs are visible on the outside face of the part.Used for: Vertical elbow H100, ULBA...
Cover for elbow available in radius R600 & R900 mm
ULBAD 100.150
7032 150ULBAD 100.200 7032 200ULBAD 100.300 7032 300ULBAD 100.400 7032 400ULBAD 100.450 7032 450ULBAD 100.500 7032 500ULBAD 100.600 7032 600ULBAD 100.750 7032 750ULBAD 100.900 7032 900
K23
K23K23K23K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
957538957545957552957569957576957583957590957613957637
Weight 100 units
pc
32,941,359,576,183,791,4
105,8137,1183,1
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, stormsfor example, the quantity of clips must be increased.
GRP cover for vertical adjustable elbowpressed
For a stronger assembly, the covers with a width above 400 mm are strengthened. Thesestrengthenings / ribs are visible on the outside face of the part.Used for: Vertical elbow 150 mm high, ULBA...
Cover for elbow available in radius R600 & R900 mm
ULBAD 150.150
7032 150ULBAD 150.200 7032 200ULBAD 150.300 7032 300ULBAD 150.400 7032 400ULBAD 150.450 7032 450ULBAD 150.500 7032 500ULBAD 150.600 7032 600ULBAD 150.750 7032 750ULBAD 150.900 7032 900
K23
K23K23K23K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
059089059096059119059126059133059140059157059164059171
Weight 100 units
38,147,969,088,297,1
106,0122,7159,0212,4
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, stormsfor example, the quantity of clips must be increased.
96
CABLE LADDER SYSTEM COVERS UL
GRP cover for tee junctionpressed
Used for: T H53, H80, H100 et H150, ULTE…
ULTED 150
7032 150ULTED 200 7032 200ULTED 300 7032 300ULTED 400 7032 400ULTED 450 7032 450ULTED 500 7032 500ULTED 600 7032 600ULTED 750 7032 750ULTED 900 7032 900
K23
K23K23K23K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
957644957651957668957675957682957699957705957729957743
Weight 100 units
pc
51556269748188
105118
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for crosspressed
For a stronger assembly, the covers with a width above 400 mm are strengthened. Thesestrengthenings / ribs are visible on the outside face of the part.Used for: GRP ladder cross H53, H80, H100 and H150, ULX…
ULXD 150
7032 150ULXD 200 7032 200ULXD 300 7032 300ULXD 400 7032 400ULXD 450 7032 450ULXD 500 7032 500ULXD 600 7032 600ULXD 750 7032 750ULXD 900 7032 900
K23
K23K23K23K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
957750957767957774957781957798957804957811957835957859
Weight 100 units
pc m/
758090
100105110120135150
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
Cover fixing clipstainless steel
for fixing the cables tray covers and fittings
Used for: Cable tray cover KKD… and KPD…Cover for fittings KKCD..., KKBD..., KKWD..., KKBAD..., KKBID..., KKETD..., KKSTD...,KKSSD..., KKRLD... and KKRRD...
DF 50 E4
55DF 80 E4 85DF 100 E4 110DF 150 E4 150
E4
E4E4E4
Item ref. Height
mm
Min. pack.
50 p.50 p.50 p.50 p.
EANcode
957873957880957897957903
Weight 100 units
pc.
1,72,12,33,4
Under normal conditions, it is recommended to mount 1 clip each meter alternatively every 3 meters.Under extreme weather conditions, such as strong winds or storms, the quantity of clips must beincreased.
Wall-mounted angle plateasymetrical
for fixing the cables ladders on the floor, or for a ceiling mounting and for a wall mounting.
Mounting accessories required : M10x30 V4A (to be ordered separately)
ULKV E4
5E4
Item ref. Materialthickness
(th)mm
Min. pack.
1 p.
EANcode
960330
Weight 100 units
pc
20
97
Cover fixing
Used for: Cover for cable tray KKD… and KPD…Cover for fittings KKCD..., KKBD..., KKWD..., KKBAD..., KKBID..., KKETD..., KKSTD...,KKSSD..., KKRLD... und KKRRD…
DFUB 5.5X19 E4
N E4
Item ref. Min. pack.
50 p.
EANcode
062065
Weight 100 units
0,64
For fixing the cover, it is necessary to drill a 8,2 mm diameter hole for the diameter. In extremeweather conditions such as strong winds, for example, the quantity of clips must be increased.
Steel tape for cover
The DFW is composed by :- 2 GRP profiles- 2 stainless steel threaded rods
to secure the cover fixing in extreme weather conditions (strong wind)
DFW 53.150
7032 53 150DFW 53.200 7032 53 200DFW 53.300 7032 53 300DFW 53.400 7032 53 400DFW 53.500 7032 53 500DFW 53.600 7032 53 600DFW 80.150 7032 80 150DFW 80.200 7032 80 200DFW 80.300 7032 80 300DFW 80.400 7032 80 400DFW 80.500 7032 80 500DFW 80.600 7032 80 600DFW 100.150 7032 100 150DFW 100.200 7032 100 200DFW 100.300 7032 100 300DFW 100.400 7032 100 400DFW 100.450 7032 100 450DFW 100.500 7032 100 500DFW 100.600 7032 100 600DFW 100.750 7032 100 750DFW 100.900 7032 100 900DFW 150.150 7032 150 150DFW 150.200 7032 150 200DFW 150.300 7032 150 300DFW 150.400 7032 150 400DFW 150.450 7032 150 450DFW 150.500 7032 150 500DFW 150.600 7032 150 600DFW 150.750 7032 150 750DFW 150.900 7032 150 900
E4 K23
E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23E4 K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
968022968039968046968053968060968077968084968091968107968114968121968138968145968152968169968176968183968190968206968213968220968237968244968251968268968275968282968299968305968312
Weight 100 units
pc
31,036,647,658,769,880,831,837,348,459,470,581,532,538,049,160,265,771,282,398,9
115,533,539,050,161,166,672,283,299,8
116,4
98
CABLE LADDER SYSTEM ACCESSOIRES UL
Ladder fixing hold down clampin GRP
Need : 2 pieces per support
for the fixing of cable ladders and fittings, on the brackets KTA, FPAP
Fixing accessories for FPAP: 2 bolts M10x30 V4A per bracket, with large washer, to be orderedseparately.The maximum admissible torque is 8 Nm for the hold down clamp. Fixing accessories for KTA : 2 bolts M6x30 V4A per bracket, to be ordered separately.
ULKG
7032 4K23
Item ref. RAL colour
Materialthickness
(th)mm
Min. pack.
1 p.
EANcode
960316
Weight 100 units
pc
3
Ladder fixing hold down clampsteel
Need : 2 pieces per support
for the fixing of cable ladders and fittings, on the brackets KTA, FPAP
Fixing accessories for FPAP: 2 bolts M10x30 V4A per bracket, with large washer, to be orderedseparately,The maximum admissible torque is 8 Nm for the hold down clamp. Fixing accessories for KTA : 2 bolts M6x30 V4A per bracket, to be ordered separately.
ULKH E4
E4
Item ref. Min. pack.
1 p.
EANcode
960323
Weight 100 units
20
BoltIncluded nut and washer
Also named M6x16V4A for FKM 6x16 E4, M6x20V4A for FKM 6x20 E4, M8x20PA6 for FKM 8x20K01, M10x30V4A for SKM 10x30 E5
for fixing the cables ladders on the brackets
BKM 6X30 E4
6 30E4
Item ref. ThreadM
LengthL
mm
Min. pack.
100 p.
EANcode
968336
Weight 100 units
pc
1,7
Dome head boltIncluded nut and washer
Also named M6x16V4A for FKM 6x16 E4, M6x20V4A for FKM 6x20 E4, M8x20PA6 for FKM 8x20K01, M10x30V4A for SKM 10x30 E4
FKM 6X16 E4
6 16FKM 6X20 E4 6 20
E4
E4
Item ref. ThreadM
LengthL
mm
Min. pack.
100 p.100 p.
EANcode
962693962709
Weight 100 units
pc
1,21,4
Dome head boltIncluded nut and washer
Also named M6x16V4A for FKM 6x16 E4, M6x20V4A for FKM 6x20 E4, M8x20PA6 for FKM 8x20K01, M10x30V4A for SKM 10x30 E4
FKM 8X20 K01
8 20K01
Item ref. ThreadM
LengthL
mm
Min. pack.
100 p.
EANcode
962716
Weight 100 units
pc
0,4
Hexagon head boltIncluded nut and washer
Also named M6x16V4A for FKM 6x16 E4, M6x20V4A for FKM 6x20 E4, M8x20PA6 for FKM 8x20K01, M10x30V4A for SKM 10x30 E4
SKM 10X30 E4
10 30SKM 10X40 E4 10 40
E4
E4
Item ref. ThreadM
LengthL
mm
Min. pack.
100 p.100 p.
EANcode
962730962747
Weight 100 units
pc
4,55,1
99
Cover fixing
Used for: Cover for cable tray KKD… and KPD…Cover for fittings KKCD..., KKBD..., KKWD..., KKBAD..., KKBID..., KKETD..., KKSTD...,KKSSD..., KKRLD... und KKRRD…
DF M
K01
Item ref. Min. pack.
50 p.
EANcode
957927
Weight 100 units
pc.
0,2
For fixing the cover, it is necessary to drill a 8,2 mm diameter hole for the diameter. In extremeweather conditions such as strong winds, for example, the quantity of clips must be increased.
Wall-mounted angle platesymetrical
for mounting on the ceiling, the wall and on the floor.
WWU 150/8 E5
4 1 SKM 8x16 E5E5
Item ref. Materialthickness
(th)
Accessories/bolts
includedmm
Min. pack.
50 p.
EANcode
728909
Weight 100 units
pc.
14,62
Fork-type self-locking plier
for the splice plates mounting
ULP 100
Item ref. Min. pack.
1 p.
EANcode
960347
Weight 100 units
pc
40
![[E4] Aire.Referencias](https://static.documents.pub/doc/80x56/55c135e1bb61eb7e3e8b4826/e4-airereferencias.jpg)
