Cablecast: Control Module Reference - Amazon S3€¦ · 2 Cablecast Control Module Reference 9. 2.1...

Control Module Reference Guide

c©Tightrope Media SystemsApplies to Cablecast 6.1.4 Build 46

Printed September 8, 2016

2

Contents

1 Introduction 51.1 What Does This Guide Cover? . . . . . . . . . . . . . . . 51.2 What this Manual Does Not Cover . . . . . . . . . . . . . 51.3 Guide Conventions . . . . . . . . . . . . . . . . . . . . . 51.4 About Tightrope . . . . . . . . . . . . . . . . . . . . . . . 6

2 Cablecast Control Module Reference 92.1 AutoPatchBCSCM . . . . . . . . . . . . . . . . . . . . . 102.2 BlackmagicVHCM . . . . . . . . . . . . . . . . . . . . . 122.3 BVSVC1CM . . . . . . . . . . . . . . . . . . . . . . . . 132.4 CodanNKCM . . . . . . . . . . . . . . . . . . . . . . . . 152.5 DenonDBT3313UDCICM . . . . . . . . . . . . . . . . . 172.6 DenonDVD2900CM . . . . . . . . . . . . . . . . . . . . 192.7 DenonV300CM . . . . . . . . . . . . . . . . . . . . . . . 212.8 DRStreamCM . . . . . . . . . . . . . . . . . . . . . . . . 232.9 Evertz8084ADCM . . . . . . . . . . . . . . . . . . . . . 252.10 ExtronISSCM . . . . . . . . . . . . . . . . . . . . . . . . 272.11 ExtronMAVCM . . . . . . . . . . . . . . . . . . . . . . . 292.12 ExtronMAVPlusCM . . . . . . . . . . . . . . . . . . . . . 312.13 ExtronSWCM . . . . . . . . . . . . . . . . . . . . . . . . 332.14 GenericCM . . . . . . . . . . . . . . . . . . . . . . . . . 352.15 GrassValleyNPCM . . . . . . . . . . . . . . . . . . . . . 362.16 IntegraDPCCM . . . . . . . . . . . . . . . . . . . . . . . 392.17 JupiterASCIICM . . . . . . . . . . . . . . . . . . . . . . 422.18 JVCSRMV232CM . . . . . . . . . . . . . . . . . . . . . 442.19 JVCSRS365UCM . . . . . . . . . . . . . . . . . . . . . . 462.20 Knox256CM . . . . . . . . . . . . . . . . . . . . . . . . 482.21 Knox64CM . . . . . . . . . . . . . . . . . . . . . . . . . 502.22 Knox8CM . . . . . . . . . . . . . . . . . . . . . . . . . . 522.23 KnoxProSwitchCM . . . . . . . . . . . . . . . . . . . . . 542.24 KnoxSDICM . . . . . . . . . . . . . . . . . . . . . . . . 562.25 Kramer2000CM . . . . . . . . . . . . . . . . . . . . . . . 582.26 LeitchRouterCM . . . . . . . . . . . . . . . . . . . . . . 602.27 LeitchRS12ACM . . . . . . . . . . . . . . . . . . . . . . 622.28 LeitchTerminalProtocolCM . . . . . . . . . . . . . . . . . 642.29 LgxMiniTProCM . . . . . . . . . . . . . . . . . . . . . . 662.30 LgxMVP2000CM . . . . . . . . . . . . . . . . . . . . . . 692.31 LgxPro16CM . . . . . . . . . . . . . . . . . . . . . . . . 712.32 LgxPro8CM . . . . . . . . . . . . . . . . . . . . . . . . . 74

3

2.33 LgxTCD1000CM . . . . . . . . . . . . . . . . . . . . . . 772.34 LgxTCDIPCM . . . . . . . . . . . . . . . . . . . . . . . 792.35 LinkAVSCM . . . . . . . . . . . . . . . . . . . . . . . . 812.36 LiveCM . . . . . . . . . . . . . . . . . . . . . . . . . . . 832.37 NCBCM . . . . . . . . . . . . . . . . . . . . . . . . . . . 842.38 NV9000CM . . . . . . . . . . . . . . . . . . . . . . . . . 862.39 OntrakADRCM . . . . . . . . . . . . . . . . . . . . . . . 882.40 PanasonicAG5700CM . . . . . . . . . . . . . . . . . . . 892.41 PanasonicAGIA232TCCM . . . . . . . . . . . . . . . . . 912.42 PanasonicAJD450CM . . . . . . . . . . . . . . . . . . . . 932.43 PesaP1CM . . . . . . . . . . . . . . . . . . . . . . . . . . 952.44 PioneerDVDV5000CM . . . . . . . . . . . . . . . . . . . 972.45 PioneerDVDV7400CM . . . . . . . . . . . . . . . . . . . 992.46 PioneerDVF07CM . . . . . . . . . . . . . . . . . . . . . 1012.47 RossAVMCM . . . . . . . . . . . . . . . . . . . . . . . . 1032.48 ShellCM . . . . . . . . . . . . . . . . . . . . . . . . . . . 1052.49 SierraSVSCM . . . . . . . . . . . . . . . . . . . . . . . . 1062.50 SigmaSCICM . . . . . . . . . . . . . . . . . . . . . . . . 1082.51 SnellSWP02CM . . . . . . . . . . . . . . . . . . . . . . . 1102.52 SonyBDP7000CM . . . . . . . . . . . . . . . . . . . . . 1122.53 SonyDSR45CM . . . . . . . . . . . . . . . . . . . . . . . 1142.54 SonyDVP777CM . . . . . . . . . . . . . . . . . . . . . . 1162.55 SXEncoderCM . . . . . . . . . . . . . . . . . . . . . . . 1182.56 SXPlayerCM . . . . . . . . . . . . . . . . . . . . . . . . 1202.57 TascamBDR2000CM . . . . . . . . . . . . . . . . . . . . 1222.58 TascamDVD6500CM . . . . . . . . . . . . . . . . . . . . 1242.59 TRMSCBLRS422CM . . . . . . . . . . . . . . . . . . . . 1262.60 TRMSIR4CM . . . . . . . . . . . . . . . . . . . . . . . . 1282.61 TRMSRelayCM . . . . . . . . . . . . . . . . . . . . . . . 1302.62 UtahScientificRCP1CM . . . . . . . . . . . . . . . . . . . 1312.63 VDCPCM . . . . . . . . . . . . . . . . . . . . . . . . . . 1332.64 VODCM . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

4

1 Introduction

Thank you for purchasing products from Tightrope Media Systems! Wehave worked hard to make your new system versatile, easy to use andreliable.

1.1 What Does This Guide Cover?

This guide is designed as a reference for how to configure the ControlModules for your system.

1.2 What this Manual Does Not Cover

This manual does not include information on the setup of Cablecast, whichis found in Cablecast: The Manual. There are extremely important conceptsthat are essential to the operation of your system. We do not cover them inthis guide.

You should be familiar with the concepts in Cablecast: The Manual, espe-cially the information in One Thousand Miles Over Cablecast.

Before digging into this guide, make sure you have read Introduction andPlanning and Initial Setup Walk-through: How Do I Set This Thing Up? inCablecast: The Manual.

1.3 Guide Conventions

Throughout this guide, the following conventions will be used:

This is a note. Notes are used to call attention to special information thatmay be helpful to keep in mind.

This is a tip. Tips show unique ways to use the software, and tricks thathave been picked up by other users.

This is a warning. Warnings call attention to actions that may result inunforeseen consequences, such as actions that delete large amounts ofdata or configurations that might have network security implications.

If we want to highlight an section of the text that is critical to a particularThis is a margin note.topic, we’ll insert a margin note, like the one you see next to this paragraph.

5

Margin notes might also include small pictures of the user interface, when afigure would be too cumbersome.! →

If we need to call special attention to something that is critical, you mightsee the symbol you that you now see to the left.

When the text references a particular menu item, field or label within thesoftware, that text will appear as follows:

Example: Click on the Main Menu button.

When we talk about or reference a menu in the software, we use a specialstyle and reference it in the margin. When we reference menus, we leaveout the main menu and we separate each menu with a colon (“:”).

Example: To edit your channel’s configuration, go to Configuration: Channel Configu-

Configuration:Channel Con-figuration

ration.

When the text references user input, “this format” will appear.

Example: When logging into Frontdoor from the main server, enter “localhost” intothe browser’s address field.

When quotes are used to display user input, do not include them in yourinput unless specifically told to do so.

You’ll notice that we’ve used a couple of ‘Examples:’ in this section. Youwill see those throughout the text. They highlight. . . examples.

1.4 About Tightrope

Tightrope Media Systems is a manufacturer of web-centric media deliveryand display systems. We strive to provide integrated solutions designedspecifically for the markets we choose to address, with a web-centric inter-face as a core design of everything we do.

For more information on Tightrope Media Systems, please visit our web site:www.trms.com

Email us at: [email protected]

Our Address is:

Tightrope Media Systems800 Transfer Road, Suite 1BSaint Paul, Minnesota 55114

For customer service, please contact your dealer or Tightrope Media Systemsdirectly:

Forum : http://forums.trms.com

Email : [email protected]

6

http://www.trms.com

mailto:[email protected]

http://forums.trms.com

mailto:[email protected]

Support Request Form : An online support request form is at www.trms.com/community.

Knowledge Base : www.trms.com/community/knowledgebase

Training Videos : www.trms.com/community/training_videos

Blogs : blog.trms.com

Chat : chat.trms.com

Phone : (866) 866-4118 / (612) 866-4118

The fastest way to get support is through email, the online support form,chat and our forum. The forum requires a free registration.

7

http://www.trms.com/community

http://www.trms.com/community/knowledgebase

http://www.trms.com/community/training_videos

http://blog.trms.com

http://chat.trms.com

8

2 Cablecast Control Module Reference

9

2.1 AutoPatchBCSCM

Controls Autopatch routers that use the BCS protocol for control.

2.1.1 Supported Devices

This Control Module is for use with video switchers manufacturered byAMX formerly Autopatch. The following models have been tested:

• AMX Routers that use the BCS protocol• Autopatch Routers that use the BCS protocol

2.1.2 Physical Connections

You will need an available RS-232 port, and an appropriate cable. The deviceend of the cable needs a female DE-9 connector.

FIGURE 2.1: RS-232 nullmodem cable

ServerServer9 pin Female9 pin Female

2 RxD3 TxD5 GND

DeviceDevice9 pin Female9 pin Female

3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND

2.1.3 Serial Port settings

Consult your device’s documentation for instructions on how to setup itsserial port. Cablecast uses the following settings:

Baud Rate : 9600 baudStop Bits : OneByte Size : 8 bits

Parity : NoneFlow Control : None

2.1.4 Location Settings: I/O: Control Module Sets Settings

Create an entry for this Control Module in the Location Settings: I/O: Con-Location Settings: I/O:Control Module Sets trol Module Sets menu. Enter the following information into the fields:

CMS Name : A descriptive name, such as “Router”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : AutoPatchBCSCM”

10

Port/IP/Local Path : Enter the serial port to which the device isconnected

Example: “2”Network Path : Leave blank

Auth : Leave blankSync Time : OFF

2.1.5 Control Module specific settings

This Control Module has additional settings in the Application Configurationfile. This file can be found at:

D:\\TRMS\Control Modules\TRMS.Services.CablecastDeviceControl.exe.config.

Please double-check any changes you make as a mis-configuration of thesesettings could cause your system to stop functioning.

AutoPatchLevels : Sets the levels that should be included inswitch commands and status requests. Specify a comma-delimited list oflevels, such as 1,2,4 for levels 1, 2 and 4. Valid levels are 1 through 8.

AutoPatchOutputs : Sets the number of outputs that should bepolled for status. For an 8x8 router enter ’8’

2.1.6 Selecting this Control Module for Router control

Navigate to Location Settings: I/O: Router. Select the Control Module SetLocation Settings: I/O:Router you previously created from the CMS that controls the router pop-down

list.

11

2.2 BlackmagicVHCM

Controls Blackmagic Videhub routers through ethernet protocol


This Control Module is for use with video switchers manufacturered byBlackmagic Design. The following models have been tested:

• Videhohub Family




ModuleExample: “localhost : BlackmagicVHCM”

Port/IP/Local Path : Enter the IP address of the deviceExample: “192.168.1.22”

Network Path : Leave blankAuth : Leave blank

Sync Time : OFF



list.

12

2.3 BVSVC1CM

Controls the VC-1 V-Chip Line 21 Encoder.


This Control Module is for use with V-Chip encoders manufacturered byBroadcast Video Systems Corp (BVS). The following models have beentested:

• VC-1

The VC-1 must be configred to accept RS-232 data. This is done bysetting jumpers JP2, 3 and 5 on the encoder board as described in theVC-1 manual.



FIGURE 2.2: RS-232 straightthrough cable


2 RxD3 TxD5 GND

DeviceDevice9 pin Male9 pin Male

2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND







CMS Name : A descriptive name, such as “V-Chip encoder”.

13

Control Module : Select the corresponding Host and ControlModule

Example: “localhost : BVSVC1CM”Port/IP/Local Path : Enter the serial port to which the device is

connectedExample: “2”


Sync Time : OFF

2.3.5 Selecting this Control Module for V-Chip control

• Navigate to Location Settings: I/O: OutputsLocation Settings: I/O:Outputs • Select your channel output

• Select the Control Module Set you previously created from the RatingCMS list

• Click Save to commit the changes

14

2.4 CodanNKCM

Controls Codan routers that use the NK protocol.


This Control Module is for use with video switchers manufacturered byCodan Broadcast (now a part of Ross Video). The following models havebeen tested:

• All routers that use the NK protocol

Newer Codan and Ross NK equipment must be controlled through theNK-SCP.


You will need an available RS-232 port, and an appropriate cable. The deviceend of the cable needs a male DE-9 connector.



2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND







CMS Name : A descriptive name, such as “Router”.

15


Example: “localhost : CodanNKCM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF





CodanNKCM-Outputs : Set to the highest numbered output, between1 and 255

CodanNKCM-Levels : Sets the levels that should be included inswitch commands and status requests. Specify a comma-delimited list oflevels, such as 1,2,4 for levels 1, 2 and 4. Valid levels are 1 through 8.



list.

16

2.5 DenonDBT3313UDCICM

Controls the DBT-3313UDCI single disc Blu-ray player. Note that thisdevice does not support the JUMP command and should be configured as aGeneric device.


This Control Module is for use with DVD players manufacturered by DenonProfessional. The following models have been tested:

• DBT-3313UDCI





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND







CMS Name : A descriptive name, such as “Denon ProfessionalDVD”.


Example: “localhost : DenonDBT3313UDCICM”

17

Port/IP/Local Path : Leave blankNetwork Path : Leave blank


2.5.5 Creating a Device

Navigate to Location Settings: I/O: Devices Click New, this will add a newLocation Settings: I/O:Devices device to the bottom of the list, called “New Input”. Click it to open the

device settings.

2.5.6 Device Settings

Enter the following information:

Name : A descriptive name for your deviceRouter Address : The router input to which this device is con-

nected, e.g. “2”Device Function : “Playback only”

Device Type : “Generic”Wake Device : Enabled if your device enters a power-saving

state. We suggest “30” seconds.Take Delay : We suggest “2” seconds

Post Roll : We suggest “5” secondsDevice CMS : Select the Control Module Set that you cre-

ated earlier for this deviceDevice Address : The serial port that controls the device, e.g.

“2”Device Formats : Select a suitable format.

Device End Actions : “Stop”

Click Save to complete the configuration of your new device.

18

2.6 DenonDVD2900CM

Controls the DVD-2900 single disc DVD player.


This Control Module is for use with DVD players manufacturered by Denon.The following models have been tested:

• DVD-2900





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND







CMS Name : A descriptive name, such as “Denon DVD”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : DenonDVD2900CM”


Auth : Leave blank

19

Sync Time : OFF



device settings.





Device Type : “DVD”Jump Duration : We suggest “15” seconds

Take Delay : We suggest “1” secondPost Roll : We suggest “5” seconds

Device CMS : Select the Control Module Set that you cre-ated earlier for this device

Device Address : The serial port that controls the device, e.g.“2”

Device Formats : Select a suitable format.Device End Actions : “Stop”


20

2.7 DenonV300CM

Controls the DN-V300 series single disc DVD players.


This Control Module is for use with DVD players manufacturered by DenonProfessional. The following models have been tested:

• DN-V300• DN-V310





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND







CMS Name : A descriptive name, such as “Denon ProfessionalDVD”.


Example: “localhost : DenonV300CM”Port/IP/Local Path : Leave blank

21


Sync Time : OFF



device settings.











22

2.8 DRStreamCM

Controls digital video encoders manufactured by Tightrope Media Systemsthat are based on the Digital Rapids Stream encoder cards.


This Control Module is for use with digital video encoders manufactureredby Tightrope Media Systems. The following models have been tested:

• ENC-106



CMS Name : A descriptive name, such as “Encoder”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : DRStreamCM”

Port/IP/Local Path : Enther the drive to which this video servershould record

Example: “E:\”Network Path : Leave blank




device settings.



Name : A descriptive name for your deviceDevice Function : “Record only”

Device Type : “Digital File”Take Delay : We suggest “0” seconds


ated earlier for this deviceDevice Address : “0”Device Formats : Select a suitable format.

Device End Actions : “StopRecord”

23

Router Output : The router output to which this device isconnected, e.g. “3”

Record Quality : Select what codec you want to use for record-ings on this device

Record Copy UNC : Leave blank. See the Cablecast manual formore information.


24

2.9 Evertz8084ADCM

Controls the 8084AD Closed Caption encoder only for inserting V-Chipdata.


This Control Module is for use with V-Chip encoders manufacturered byEvertz. The following models have been tested:

• 8084AD

The device must be configured to use the baud rate and parity describedbelow.





2 RxD3 TxD5 GND


3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND




Parity : NoneFlow Control : Software (XOn - XOff)



CMS Name : A descriptive name, such as “V-Chip encoder”.

25


Example: “localhost : Evertz8084ADCM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF

2.9.5 Selecting this Control Module for V-Chip control

• Navigate to Location Settings: I/O: OutputsLocation Settings: I/O:Outputs • Select your channel output

• Select the Control Module Set you previously created from the RatingCMS list

• Click Save to commit the changes

26

2.10 ExtronISSCM

Controls Extron seamless switchers with two outputs.


This Control Module is for use with video switchers manufacturered byExtron Electronics. The following models have been tested:

• ISG 506• ISS 408• SGS 408

This control module works only with the specified models.





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








27


Example: “localhost : ExtronISSCM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF



list.

28

2.11 ExtronMAVCM

Controls Extron MAV series routers that use the SIS protocol.



• MAV 88 AV• MAV 88 AV RCA

The ExtronMAVPlusCM should also control these routers. The two con-trol modules differ in the way they interpret router status. If this ControlModule does not work as you expect, please try the ExtronMAVPlusCM.





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








29


Example: “localhost : ExtronMAVCM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF



list.

30

2.12 ExtronMAVPlusCM

Controls Extron MAV Plus series routers that use the SIS protocol.



• MAV Plus 1212 AV• MAV Plus 4848 AV

The ExtronMAVCM should also control these routers. The two controlmodules differ in the way they interpret router status. If this ControlModule does not work as you expect, please try the ExtronMAVCM.





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








31


Example: “localhost : ExtronMAVPlusCM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF



list.

32

2.13 ExtronSWCM

Controls Extron SW series switchers.



• SW 12AV RCA• SW 6AV

The ExtronSWCM will only control single-output switchers. If you aretrying to control a routing switcher with more than one output, check outthe ExtronMAVPlusCM





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








33


Example: “localhost : ExtronSWCM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF



list.

34

2.14 GenericCM

This is a diagnostic control module. It does not control any devices andserves no function aside from development and testing.

35

2.15 GrassValleyNPCM

Control for Routers that use the Grass Valley Native Protocol (aka Series7000)


This Control Module is for use with video switchers manufacturered by GrassValley Native Protocol. The following models have been tested:

• AJA KUMO Series Routers

This Control Module should work with any router that is controlled by theGrass Valley Native Protocol. This control module has only been testedagainst the KUMO routers by AJA and the Ross NK-3RD protocol con-verter. When using the Ross NK-3RD the "GrassValleyNPCM-UseHex"config must be set to "True"



The cable required for this device depends upon what type of RS-422 portyou are using.

FIGURE 2.12: Quatech RS-422cable

FIGURE 2.13: BlastronixRS-422 cable

ServerServer9 pin Male9 pin Male

2 RxD -3 TxD +7 RxD +8 TxD -


2 TxD -3 RxD +7 TxD +8 RxD -





36








ModuleExample: “localhost : GrassValleyNPCM”








GrassValleyNPCM-Baud-Rate : The baud rate for this device. Default is38400.

GrassValleyNPCM-Outputs : Comma delimited list of outputs. These out-puts will be used for requesting crosspoint status. Default is 0 through 15 i.e.(0,1,2,3...)

GrassValleyNPCM-UseHex : Configures the router to use hexadecimalwhen parsing sources and destinations. This setting depends on the manu-facturer of your router. Default is False

37



list.

38

2.16 IntegraDPCCM

Controls DPC series DVD changers.


This Control Module is for use with DVD changers manufacturered byIntegra. The following models have been tested:

• The DPC series of DVD changers

The Integra protocol does not support a jump command. Playback willalways start at title 1, chapter 1.





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND







CMS Name : A descriptive name, such as “Integra DVDChanger”.

39


Example: “localhost : IntegraDPCCM”Port/IP/Local Path : Leave blank


Sync Time : OFF





IntegraForceStop : Set this to true if you are having problemswith auto-start discs in this changer



device settings.





Device Type : “DVD(Multidisc)”Load Duration : We suggest “30” secondsJump Duration : We suggest “15” seconds



Device Slots : “1” to “6”Device Address : The serial port that controls the device, e.g.



40


41

2.17 JupiterASCIICM

Controls routers that use the Jupiter ASCII protocol.


This Control Module is for use with video switchers manufacturered byPhillips Broadcast (now a part of Grass Valley). The following models havebeen tested:

• Routers that use the Jupiter ASCII protocol

Router size is limited to 1000 inputs and 1000 outputs (000-999) andseven levels.





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND




Parity : NoneFlow Control : Software (XOn - XOff)




42


Example: “localhost : JupiterASCIICM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF





JupiterASCIICM-Levels : A comma-delimited list of levels that shouldbe switched. The first value will be used for status requests.

JupiterASCIICM-Outputs : A comma-delimited list of outputs that shouldbe included in status requests



list.

43

2.18 JVCSRMV232CM

Controls DVD / VHS / Mini-DV combo decks from JVC.


This Control Module is for use with combo decks manufacturered by JVC.The following models have been tested:

• SR-DVM600• SR-DVM70• SR-MV45• SR-MV50• SR-MV55

This control module can’t switch the mode of the device. So, a playcommand will be sent to whatever mechanism is currently controlled. Ifyou are using the tape portion of the deck you should set the Device Typeto Generic. Some decks may need a null-modem cable.





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND





44



CMS Name : A descriptive name, such as “JVC ComboDeck”.


Example: “localhost : JVCSRMV232CM”Port/IP/Local Path : Leave blank


Sync Time : OFF



device settings.











45

2.19 JVCSRS365UCM

Controls S-VHS decks from JVC.


This Control Module is for use with timecode VTRs manufacturered by JVC.The following models have been tested:

• SR-365U

The Control Mode switch under the front flap must be set to RS232





2 RxD3 TxD5 GND


3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND







CMS Name : A descriptive name, such as “JVC VTR”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : JVCSRS365UCM”

Port/IP/Local Path : Leave blank

46


Sync Time : OFF



device settings.





Device Type : “VTR”Jump Duration : We suggest “60” seconds

Take Delay : We suggest “2” secondsPost Roll : We suggest “5” seconds



Device Formats : Select a suitable format.Device End Actions : “Stop + Rewind”


47

2.20 Knox256CM

Controls Knox routers that have more than 99 inputs and outputs.


This Control Module is for use with video switchers manufacturered byKnox Video Technologies. The following models have been tested:

• Chameleon256





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








ModuleExample: “localhost : Knox256CM”


Example: “2”

48


Sync Time : OFF



list.

49

2.21 Knox64CM

Controls modular routing switchers with up to 99 inputs and outputs.



• Chameleon• Chameleon64• Chameleon64i• RS 16x16• RSII Series





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








50


Example: “localhost : Knox64CM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF



list.

51

2.22 Knox8CM

Controls Knox routers that have less than 10 inputs and outputs.



• RS 4x4• RS 8x8





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








ModuleExample: “localhost : Knox8CM”

52






list.

53

2.23 KnoxProSwitchCM

Controls Knox ProSwitch series routers.



• ProSwitch series





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








ModuleExample: “localhost : KnoxProSwitchCM”


Example: “2”

54


Sync Time : OFF



list.

55

2.24 KnoxSDICM

Controls SDI souting switchers.



• SDI 8x8

You should disable ’Verbose’ mode on the router by setting DIP switch#3 to OFF





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








ModuleExample: “localhost : KnoxSDICM”

56






list.

57

2.25 Kramer2000CM

Controls Kramer routers that are controllable using Protocol 2000.


This Control Module is for use with video switchers manufacturered byKramer Electronics. The following models have been tested:

• Routers that use ’Protocol 2000’

These routers allow you to set a ’Machine ID’, Cablecast always controlsMachine ID 1. Please make sure your router is set accordingly. Forinformation on how to change the Machine ID, please consult the router’sdocumentation.





2 RxD3 TxD5 GND


3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND








58


Example: “localhost : Kramer2000CM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF





Kramer2000CMOutputs : This setting allows you to set the total num-ber of outptus on the router (i.e. ’8’). If you don’t set this, cablecast willasume there are 100 outputs. Setting this to the actual number of outputswill make the force menu load faster.

Kramer2000CMUseBreakawayMode : Setting this to ’true’ will cause switches tobe executed in breakaway mode. A ’Disable Breakaway’ command will besent, followed by a ’Switch Video’ and a ’Switch Audio’. If set to ’false’,a ’EnableBreakaway’ command will be sent, followed by a ’Switch Video’command.

Kramer2000CMIgnoreBreakawayMode : Setting this to ’true’ will cause switches tobe executed as a ’Switch Video’ command followed by a ’Switch Audio’command.

Kramer2000IgnoreAudioEvents : When Kramer2000CMIgnoreBreakawayModeis set to ’false’ and Kramer2000CMUseBreakawayMode is set to ’true’, thiswill cause the ’Switch Audio’ command to be skipped.



list.

59

2.26 LeitchRouterCM

Controls Leitch and Harris routers that use the XY protocol.


This Control Module is for use with video switchers manufacturered byLeitch (now part of Harris). The following models have been tested:

• Routers that support XY protocol

The LeitchTerminalProtocolCM may also be able to control your router.If the PortSetting field is defined as an integer serial control will beattempted. Otherwise the PortSetting field will be used as a networkaddress to control the router via TCP IP





2 RxD3 TxD5 GND


3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND








60


Example: “localhost : LeitchRouterCM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF





LeitchRouterCM-Levels : Comma delimited list of levels to switch. Ex-ample 0,1,2. If "LeitchRouterCM-Outputs" is defined the first defined levelwill be used for status.

LeitchRouterCM-EnableReporting : Setting this to ’true’ will cause an Enablereporting "@ ?.̊" command to be sent before router status is requested.

LeitchRouterCM-Outputs : Comma delimited list of outputs to poll forstatus. If undefined, "@ S?0"̊ will be used, which may not be supporte donall devices.



list.

61

2.27 LeitchRS12ACM

Controls Videotek or Leitch RS-12A routers.


This Control Module is for use with video switchers manufacturered byVideotek or Leitch (both now part of Harris). The following models havebeen tested:

• RS-12A





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND




Parity : OddFlow Control : None




ModuleExample: “localhost : LeitchRS12ACM”

62






list.

63

2.28 LeitchTerminalProtocolCM

Controls Leitch and Harris routers that use Leitch Terminal protocol.


This Control Module is for use with video switchers manufacturered byLeitch (now part of Harris). The following models have been tested:

• Routers that support Leitch Terminal protocol

The LeitchRouterCM may also be able to control your router.





2 RxD3 TxD5 GND


3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND








ModuleExample: “localhost : LeitchTerminalProtocolCM”

64








LeitchTerminalProtocolCM-Levels : Sets the Level(s) that should be switched



list.

65

2.29 LgxMiniTProCM

Controls Mini-T Pro event controllers. Does not support Mini-T NX units.


This Control Module is for use with event controllers manufacturered byLeightronix. The following models have been tested:

• Mini-T Pro

The Mini-T Pro is both a routing switcher, and a device controller. Thefollowing Device configuration instructions indicate how to configure ageneric VTR for control.





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND







CMS Name : A descriptive name, such as “Mini-T Pro”.

66


Example: “localhost : LgxMiniTProCM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF


Navigate to Location Settings: I/O: Router.Location Settings: I/O:Router

You don’t need to use the built-in routing switcher.

Select the Control Module Set you previously created from the CMS thatcontrols the router pop-down list.



device settings.


This device is both a router and a device controller. The following settingsgive a general example as to how a device is configured, but your settingswill likely be slightly different







ated earlier for this deviceDevice Address : For ProBus devices: the device ID, such as

“3”.Device Formats : Select a suitable format.

67

Device End Actions : “Stop + Rewind”


68

2.30 LgxMVP2000CM

Controls MVP-2000 event controllers.


This Control Module is for use with devices manufacturered by Leightronix.The following models have been tested:

• MVP-2000

Cablecast 5.0 and later only supports the MVP-2000’s device controlfeatures.



CMS Name : A descriptive name, such as “MVP-2000”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : LgxMVP2000CM”



Sync Time : OFF



device settings.






Device Type : “Generic”

69

Wake Device : Enabled if your device enters a power-savingstate. We suggest “30” seconds.



Device Address : For ProBus devices: the device ID, such as“3”.



70

2.31 LgxPro16CM

Controls Pro-16 event controllers.



• Pro-16

The Pro-16 is both a routing switcher, and a device controller. Thefollowing Device configuration instructions indicate how to configure ageneric VTR for control.





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND







CMS Name : A descriptive name, such as “Pro-16”.

71


Example: “localhost : LgxPro16CM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF







device settings.











72



73

2.32 LgxPro8CM

Controls Pro-8 event controllers.



• Pro-8

The Pro-8 is both a routing switcher, and a device controller. The follow-ing Device configuration instructions indicate how to configure a genericVTR for control.





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND







CMS Name : A descriptive name, such as “Pro-8”.

74


Example: “localhost : LgxPro8CM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF







device settings.











75



76

2.33 LgxTCD1000CM

Controls TCD-1000 event controllers.



• TCD-1000

The TCD-1000 can control multiple devices using it’s ProBus and LGXconnections..


You will need an available RS-232 port, and an appropriate cable. The deviceend of the cable needs a female DB-25 connector.

FIGURE 2.30: RS-232 9 to 25pin straight through cable


2 RxD3 TxD5 GND7 RTS8 CTS













CMS Name : A descriptive name, such as “TCD-1000”.

77


Example: “localhost : LgxTCD1000CM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF



device settings.













78

2.34 LgxTCDIPCM

Controls TCD-IP event controllers.



• TCD-IP

The TCD-IP is a device controller. The following Device configurationinstructions indicate how to configure it to control a generic VTR..



CMS Name : A descriptive name, such as “TCD-IP”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : LgxTCDIPCM”



Sync Time : OFF



device settings.






Device Type : “Generic”

79




Device Address : For ProBus devices: the device ID, e.g. “4”.For PlusBus devices: the device symbol, e.g. “PLUSBUS DVDCHG01”.



80

2.35 LinkAVSCM

Controls AVS series single-output switchers


This Control Module is for use with video switchers manufacturered by LinkElectronics. The following models have been tested:

• AVS-816





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








ModuleExample: “localhost : LinkAVSCM”


Example: “2”

81


Sync Time : OFF



list.

82

2.36 LiveCM

This is a diagnostic control module. It does not control any devices andserves no function aside from development and testing.

83

2.37 NCBCM

Controls Nevion Routers that use the NCB Protocol


This Control Module is for use with video switchers manufacturered byNCB. The following models have been tested:

•





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








ModuleExample: “localhost : NCBCM”


Example: “2”

84


Sync Time : OFF



list.

85

2.38 NV9000CM

Controls Miranda routers that are controllable using NVision 9000 proto-col.


This Control Module is for use with video switchers manufacturered byNVision. The following models have been tested:

• Routers that use ’NV9000 Prootocol’
















Baud Rate : 38400 baudStop Bits : One

86

Byte Size : 8 bitsParity : None

Flow Control : None




ModuleExample: “localhost : NV9000CM”








NV9000-Outputs : A comma delimted list of outputs to poll forstatus. Example: 1,4,9

NV9000-Level : Level to which switch and status commandswill be addressed.



list.

87

2.39 OntrakADRCM

Allows control of contact closure compaitble devices.


This Control Module is for use with devices manufacturered by Ontrak. Thefollowing models have been tested:

• ADR2200• ADR2205







CMS Name : A descriptive name, such as “ADR2200”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : OntrakADRCM”




88

2.40 PanasonicAG5700CM

Controls S-VHS decks from Panasonic.


This Control Module is for use with timecode VTRs manufacturered byPanasonic. The following models have been tested:

• AG-5700

The Local/Remote switch on the front panel must be set to Remote


You will need an available RS-232 port, and an appropriate cable. The deviceend of the cable needs a male DB-25 connector.
















CMS Name : A descriptive name, such as “PanasonicVTR”.

89


Example: “localhost : PanasonicAG5700CM”Port/IP/Local Path : Leave blank


Sync Time : OFF



device settings.











90

2.41 PanasonicAGIA232TCCM

Controls S-VHS decks from Panasonic.



• Decks with the AG-IA232TC Module installed




















91


Example: “localhost : PanasonicAGIA232TCCM”Port/IP/Local Path : Leave blank


Sync Time : OFF



device settings.











92

2.42 PanasonicAJD450CM

Controls DVCPRO decks from Panasonic.



• AJ-DV440P• AJ-DV450P



















93



Example: “localhost : PanasonicAJD450CM”Port/IP/Local Path : Leave blank


Sync Time : OFF



device settings.











94

2.43 PesaP1CM

Controls Pesa routers that use the P1 protocol.


This Control Module is for use with video switchers manufacturered by PesaSwitching Systems. The following models have been tested:

• Routers that use the P1 protocol






Parity : NoneFlow Control : Hardware




ModuleExample: “localhost : PesaP1CM”







95


PesaLevels : Defines the number of levels that the routerhas. For example, a router with video and stereo audio would have 3 levels.

PesaOutputs : Defines the number of outputs that the routerhas. Status will only be requested for this many outputs. If your router is8x8, set this to 8.



list.

96

2.44 PioneerDVDV5000CM

Controls DVD Players from Pioneer.


This Control Module is for use with DVD players manufacturered by PioneerElectronics. The following models have been tested:

• DVD-V5000

There is a menu setting that should be checked. With no disc in the player,press and hold the HOME MENU button until the settings menu comesup. Ensure that 9-pin is selected for SERIAL PORT, and that the BAUDRATE is set to 19200





2 RxD3 TxD5 GND


3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND







CMS Name : A descriptive name, such as “Pioneer ElectronicsDVD”.

97


Example: “localhost : PioneerDVDV5000CM”Port/IP/Local Path : Leave blank


Sync Time : OFF



device settings.











98

2.45 PioneerDVDV7400CM

Controls Industrial DVD Players decks from Pioneer.


This Control Module is for use with DVD players manufacturered by PioneerElectronics. The following models have been tested:

• DVD-V7400

There is a menu setting that should be checked. Press and hold theSETUP button for one second, the ADVSETUP menu should appear.Ensure that BAUD RATE is set to 4800bps


You will need an available RS-232 port, and an appropriate cable. The deviceend of the cable needs a male DA-15 connector.

FIGURE 2.39: Pioneer RS-232cable


2 RxD3 TxD5 GND


2 RxD3 TxD1 GND


2 RxD3 TxD5 GND


2 RxD3 TxD1 GND







CMS Name : A descriptive name, such as “Pioneer ElectronicsDVD”.

99


Example: “localhost : PioneerDVDV7400CM”Port/IP/Local Path : Leave blank


Sync Time : OFF



device settings.











100

2.46 PioneerDVF07CM

Controls DV-F07 300 disc DVD changers.


This Control Module is for use with DVD changers manufacturered byPioneer Electronics. The following models have been tested:

• DV-F07

Stick-on DVD labels will cause serious damage to your DVD changer.We strongly suggest purchasing printable DVDs.


You will need an available RS-232 port, and an appropriate cable. The deviceend of the cable needs a male DA-15 connector.

FIGURE 2.40: Pioneer RS-232cable


2 RxD3 TxD5 GND


2 RxD3 TxD1 GND


2 RxD3 TxD5 GND


2 RxD3 TxD1 GND







CMS Name : A descriptive name, such as “Pioneer ElectronicsDVD Changer”.

101


Example: “localhost : PioneerDVF07CM”Port/IP/Local Path : Leave blank


Sync Time : OFF



device settings.












102

2.47 RossAVMCM

Controls Ross AVM switchers.


This Control Module is for use with video switchers manufacturered by RossVideo. The following models have been tested:

• All AVM switchers

















103





ModuleExample: “localhost : RossAVMCM”






list.

104

2.48 ShellCM

This Control Module will run a user-created program when every eventoccurs. It will pass relevant information to the program so that the appro-priate action can be taken. For more information, please contact TRMSsupport.

105

2.49 SierraSVSCM

Controls Sierra routers that use the SVS protocol.


This Control Module is for use with video switchers manufacturered bySierra Video Systems. The following models have been tested:

• All routers that use the SVS protocol

Newer Sierra routers use a standard straight-through serial cable forcontrol. We suggest you try that first, if it does not work, you may needto build the custom cable outlined below.



FIGURE 2.43: Sierra RS-232cable


2 RxD3 TxD5 GND

RouterRouter9 pin Male9 pin Male

2 TxD8 RxD1 GND


2 RxD3 TxD5 GND

RouterRouter9 pin Male9 pin Male

2 TxD8 RxD1 GND








106


Example: “localhost : SierraSVSCM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF





SierraSVS-Levels : Sets the levels that should be included inswitch commands and status requests. Setting this to 0 will switch all levels.Otherwise, you can specify a comma-delimited list of levels, such as 1,2,4for levels 1, 2 and 4.



list.

107

2.50 SigmaSCICM

Controls Sigma routers that use the SCI protocol.


This Control Module is for use with video switchers manufacturered bySigma Technology Systems. The following models have been tested:

• All routers that use the SCI protocol





2 RxD3 TxD5 GND


3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND








ModuleExample: “localhost : SigmaSCICM”


Example: “2”

108


Sync Time : OFF



list.

109

2.51 SnellSWP02CM

Controls all routers that use the Snell General Switcher CommunicationProtocol


This Control Module is for use with video switchers manufacturered bySnell (formerly Snell and Wilcox, Pro-Bel). The following models havebeen tested:

• Vega series




ModuleExample: “localhost : SnellSWP02CM”



Sync Time : OFF





SnellSWP02CMFirstOutput : Defines the one-based address of the firstoutput on the router. For most routers this should be set to 1. For Vegarouters the value depends on configuration

SnellSWP02CMLastOutput : Defines the one-based address of the last out-put on the router. For most routers this will be set to the number of outputs,e.g. 32. For Vega routers the value depends on configuration


Navigate to Location Settings: I/O: Router. Select the Control Module SetLocation Settings: I/O:Router

110

you previously created from the CMS that controls the router pop-downlist.

111

2.52 SonyBDP7000CM

Controls BDP-CX7000ES 400 disc Blu-ray changers.


This Control Module is for use with DVD changers manufacturered by Sony.The following models have been tested:

• BDP-CX7000ES






2 RxD3 TxD5 GND


3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND







CMS Name : A descriptive name, such as “Sony DVD Changer”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : SonyBDP7000CM”

112





device settings.












113

2.53 SonyDSR45CM

Controls DVCAM decks from Sony.


This Control Module is for use with timecode VTRs manufacturered bySony. The following models have been tested:

• DSR-45

The rear-panel REMOTE switch must be set to RS-232C. The front-panelREMOTE/LOCAL switch must be set to REMOTE.





2 RxD3 TxD5 GND


3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND







CMS Name : A descriptive name, such as “Sony VTR”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : SonyDSR45CM”

114





device settings.











115

2.54 SonyDVP777CM

Controls DVP-CX777ES 400 disc DVD changers.


This Control Module is for use with DVD changers manufacturered by Sony.The following models have been tested:

• DVP-CX777ES






2 RxD3 TxD5 GND


3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND







CMS Name : A descriptive name, such as “Sony DVD Changer”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : SonyDVP777CM”

116





device settings.












117

2.55 SXEncoderCM

Controls the built-in encoders in SX series video servers.


This Control Module is for use with digital video encoders manufactureredby Tightrope Media Systems. The following models have been tested:

• SX-2• SX-2HD• SX-4• SX-LE



CMS Name : A descriptive name, such as “Encoder”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : SXEncoderCM”

Port/IP/Local Path : Enther the drive to which this video servershould record

Example: “E:\”Network Path : Leave blank




device settings.



Name : A descriptive name for your deviceDevice Function : “Record only”



ated earlier for this deviceDevice Address : The encoder that this device represents, “0”

or “1”

118

Device Formats : Select a suitable format.Device End Actions : “StopRecord”

Router Output : The router output to which this device isconnected, e.g. “3”

Record Quality : Select what codec you want to use for record-ings on this device

Record Copy UNC : Leave blank. See the Cablecast manual formore information.


119

2.56 SXPlayerCM

Controls the video decoders in the SX series video servers.


This Control Module is for use with digital video servers manufacturered byTightrope Media Systems. The following models have been tested:

• SX-2• SX-2HD• SX-4• SX-LE



CMS Name : A descriptive name, such as “Server Playback”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : SXPlayerCM”

Port/IP/Local Path : Enter the content drive or drives that thisvideo server will play from, multiple drives should be separated by a pipecharacter

Example: “E:\|F:\”Network Path : Leave blank




device settings.






Post Roll : We suggest “0” seconds

120


Device Address : The playback channel that this device repre-sents, starting with “0”

Device Formats : Select a suitable format.Device End Actions : “None”


121

2.57 TascamBDR2000CM

Controls DVD and Blueray playback on Tascam BD-R2000


This Control Module is for use with DVD players manufacturered by Tascam.The following models have been tested:

• DSR-45

Set QUICK STARTUP to ON in device menu.





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND







CMS Name : A descriptive name, such as “Tascam DVD”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : TascamBDR2000CM”

Port/IP/Local Path : Leave blank

122


Sync Time : OFF



device settings.











123

2.58 TascamDVD6500CM

Controls Industrial DVD Players decks from Tascam.


This Control Module is for use with DVD players manufacturered by Tascam.The following models have been tested:

• DV-D01U• DV-D6500





2 RxD3 TxD5 GND


3 TxD2 RxD5 GND


2 RxD3 TxD5 GND


3 TxD2 RxD5 GND







CMS Name : A descriptive name, such as “Tascam DVD”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : TascamDVD6500CM”

124






device settings.








Device Address : Leave blankDevice Formats : Select a suitable format.



125

2.59 TRMSCBLRS422CM

Controls VTRs and other devices that support the Sony RS422 proto-col.


This Control Module is for use with timecode VTRs manufacturered byvarious manufacturers that support the Sony RS422 protocol. The followingmodels have been tested:

• Sony DSR-1500• Sony DSR-2000• Sony DSR-45
















126





CMS Name : A descriptive name, such as “various manufacturersthat support the Sony RS422 protocol VTR”.


Example: “localhost : TRMSCBLRS422CM”Port/IP/Local Path : Leave blank


Sync Time : OFF



device settings.











127

2.60 TRMSIR4CM

Controls the IR-4 IR Expander. This unit is used to control up to four IRdevices


This Control Module is for use with devices manufacturered by TightropeMedia Systems. The following models have been tested:

• IR-4

You need to use the IR Learner application to learn the appropriatecommands for your devices before this Control Module will work. Thisapplication can be found in D:\TRMS\ Tools.



CMS Name : A descriptive name, such as “IR-4”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : TRMSIR4CM”






device settings.




Name : A descriptive name for your device

128

Router Address : The router input to which this device is con-nected, e.g. “2”

Device Function : “Playback only”Device Type : “Generic”




Device Address : The IR port to which the deck is connected,“1” . . . “4”



129

2.61 TRMSRelayCM

Uses the RTS line of the serial port to control external devices. A Play eventwill set RTS, a Stop event will clear it

130

2.62 UtahScientificRCP1CM

Controls Utah routers that use the RCP1 protocol.


This Control Module is for use with video switchers manufacturered by UtahScientific. The following models have been tested:

• Routers that use the RCP1 protocol

Your router’s control board may have a jumper that selects the serial portmode, you should set it to RS-232. For 100x series routers, you must usea DB9 null-modem cable with ONLY pins 2,3 and 5 wired.





2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND


2 RxD3 TxD5 GND








131


Example: “localhost : UtahScientificRCP1CM”Port/IP/Local Path : Enter the serial port to which the device is



Sync Time : OFF





UtahScientificRPC1-Outputs : Sets the outputs that status will be requestedfor. This list is zero based, so the first output on the router is 0. Enter this asa comma-delimited list, for example 0,1,2,3,7,42.

UtahScientificRPC1-Levels : Sets the levels that will be switched and thatstatus will be requested for. This list is one based, so the first level is 1. Enterthis as a comma-delimited list, for example 1,2,3,6,7

UtahScientificRPC1-BaudRate : The baud rate that will be used for serialcommunication. If not set 9600 will be used. For use with 100x seriesrouters, this must be set to 19200



list.

132

2.63 VDCPCM

Controls Video Servers that support the VDCP protocol.


This Control Module is for use with digital video servers manufactureredby various manufacturers that support the VDCP protocol. The followingmodels have been tested:

• 360 Systems Imageserver• 360 Systems Imageserver 2000• 360 Systems Imageserver MAXX• Ross Softmetal

Files on the VDCP controlled server must be named showid-reelnumbere.g. ’12345-1’. The Reel Number is required, and no file extension isallowed














133







CMS Name : A descriptive name, such as “Server Playback”.Control Module : Select the corresponding Host and Control

ModuleExample: “localhost : VDCPCM”


Example: “2”NetworkPath : Enter the IP Address of the device

Example: “192.168.1.10”Auth : Leave blank

Sync Time : OFF



device settings.







ated earlier for this device

134

Device Address : The playback channel that this device repre-sents, starting with “1”

Device Formats : Select a suitable format.Device End Actions : “None”


135

2.64 VODCM

Performs VOD operations like transcoding and file discovery.

136

Date post:	30-May-2020
Category:	Documents
Upload:	others
View:	11 times
Download:	0 times

Cablecast: Control Module Reference - Amazon S3€¦ · 2 Cablecast Control Module Reference 9. 2.1...

Documents