Cad Manual

CREATION OF SIMPLE BLLOCK

AIM: creation of simple block by using the commands of circle, point, trim, mirror, etc

Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300

Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model.

Command: lineSpecify first point: 110,50Specify next point or [Undo]: 260,50Specify next point or [Undo]: 260,180Specify next point or [Close/Undo]: 110,180Specify next point or [Close/Undo]: close

Command: pointSpecify the point :185,180

Command: _circle Specify center point for circle or [3P/2P/Ttr (tan tan /radius)]: 185,180Specify radius of circle or [Diameter]: 35

Command: arcSpecify start point of arc or [Center]: ceSpecify center point of arc: @45<0Specify end point of arc or [Angle/chord Length]: ASpecify included angle: 180

Command :TrimSelect the object: pick the source objectSelect the object to trim : trim unwanted line

Command: lineSpecify first point: 135,125Specify next point or [Undo]: 235,135 ENTER

Command :pointSpecify the point:235,95

Command: arcSpecify start point of arc or [Center]: ceSpecify center point of arc: (pick the start point )(110,50)Specify end point of arc or [Angle/chord Length]: (pick the end point )(235,125)

Command:mirrorSelect the object: pick the arcSpecify first point of mirror line: pick the mid point of line 1Specify next point of mirror line: pick the mid point of line2 Delete the source objects:{yes/no}:no ENTER

RESULT:Thus the Simple Block Drawing Was Created Successfully Using Auto Cad

Software

CREATION OF RECTANGLE

Aim : To create a rectangle using Auto CAD Software.



Command: lineSpecify first point: 110,50Specify next point or [Undo]: 260,50Specify next point or [Undo]: 260,180Specify next point or [Close/Undo]: 110,180Specify next point or [Close/Undo]: close

RESULT:Thus the rectangle Drawing Was Created Successfully Using Auto Cad

Software

CREATION OF CONE

Aim : To create front view and top view of cone using Auto CAD Software



FRONT VIEW:

Command: LineSpecify first point: pick any pointSpecify next point or [Undo]: 50Specify next point or [Undo]: @75<108Specify next point or [Close/Undo]: close

TOP VIEW

Command: circleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]:pick any pointSpecify radius of circle or [Diameter] <35.0000>: DSpecify diameter of circle <70.0000>: 50 ENTER

RESULT:Thus the cone Drawing Was Created Successfully Using Auto Cad Software

CREATION OF CYLINDER

Aim : To create front view and top view of cylinder using Auto CAD Software



FRONT VIEW:

Command: LINESpecify first point: pick any pointSpecify next point or [Undo]: 40Specify next point or [Undo]: 75Specify next point or [Close/Undo]: close

TOP VIEW

Command: circleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]:pick any pointSpecify radius of circle or [Diameter] <35.0000>: DSpecify diameter of circle <70.0000>: 40 ENTER

RESULT:Thus the front view and top view of a cylinder Drawing Was Created

Successfully Using Auto Cad Software

CREATION OF HEXAGONAL PRISM

Aim : To draw the front view and top view of hexagonal prism height of 70 mm and edge 35 mm using Auto CAD Software


Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model

FRONT VIEW:

Command: LINESpecify first point: pick the point with respect to (a)Specify next point or [Undo]: point with respect to (b)Specify next point or [Undo]: 70Specify next point or [Undo]: 70Specify next point or [Close/Undo]: close

TOP VIEW

Command: polygonEnter number of sides <4>: 6Specify center of polygon or [Edge]: eSpecify first endpoint of edge: Specify second endpoint of edge: 35 enter

RESULT:Thus the front view and top view of a hexagonal prism Drawing Was

Created Successfully Using Auto Cad Software

CREATION OF PENTAGONAL PRISM

Aim : To draw the front view and top view of pentagonal prism height of 70 mm and edge 35 mm using Auto CAD Software

Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000, 0.0000>: 0,0Specify upper right corner <12.0000, 9.0000>: 300,300


FRONT VIEW:

Command: LineSpecify first point: pick the point with respect to (a)Specify next point or [Undo]: point with respect to (b)Specify next point or [Undo]: 70Specify next point or [Undo]: 70Specify next point or [Close/Undo]: close

TOP VIEW

Command: PolygonEnter number of sides <4>: 5Specify center of polygon or [Edge]: eSpecify first endpoint of edge: Specify second endpoint of edge: 35 enter

RESULT:Thus the front view and top view of pentagonal prism Drawing Was Created

Successfully Using Auto Cad Software

CREATION OF TITLE BLOCK

Aim : To draw the following title block with necessary text and projection symbol using Auto CAD Software.



Command: LINESpecify first point: 100,150Specify next point or [Undo]: @230,0Specify next point or [Undo]: @0,130Specify next point or [Close/Undo]: @-230,0Specify next point or [Close/Undo]: close

Command: OffsetSpecify offset distance or [Through] <25.0000>: 25Select object to offset or <exit>: LINE 1Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: ENTER

Command: LINESpecify first point: 190,125Specify next point or [Undo]: @0,45Specify next point or [Undo]: @140,0 ENTER

Command: OffsetSpecify offset distance or [Through] <25.0000>: 15Select object to offset or <exit>: LINE 2Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: LINE 3Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: LINE 3Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: LAST CRAEATED LINE ENTER

Command: LINESpecify first point: 190,170Specify next point or [Undo]: @0,60 ENTER

Command: OffsetSpecify offset distance or [Through] <25.0000>: 15Select object to offset or <exit>: LINE ASpecify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: LAST CREATED LINE Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: LAST CREATED LINE Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: ENTER

Command: OffsetSpecify offset distance or [Through] <25.0000>: 20Select object to offset or <exit>: LINE BSpecify point on side to offset: →RIGHT PSIDESelect object to offset or <exit>: ENTER

Command: OffsetSpecify offset distance or [Through] <25.0000>: 50 Select object to offset or <exit>: LAST CREATED LINESpecify point on side to offset: →RIGHT PSIDESelect object to offset or <exit>: ENTER

Command: OffsetSpecify offset distance or [Through] <25.0000>: 35Select object to offset or <exit>: LAST CREATED LINESpecify point on side to offset: →RIGHT SIDESelect object to offset or <exit>: LAST CREATED LINESpecify point on side to offset: →RIGHT SIDESelect object to offset or <exit>: ENTER

CREATING THE TEXT Command: TextCurrent text style: "Standard" Text height: 0.2000Specify start point of text or [Justify/Style]: 105,118Specify height <0.2000>: 3.5Specify rotation angle of text <0>: 0Enter text: TITLE

Command: TextCurrent text style: "Standard” Text height: 0.2000Specify start point of text or [Justify/Style]: 115,105Specify height <0.2000>: 7.5Specify rotation angle of text <0>: 0Enter text: LAYOUT

Command: TextCurrent text style: "Standard” Text height: 0.2000Specify start point of text or [Justify/Style]: 225,105Specify height <0.2000>: 7.5Specify rotation angle of text <0>: 0Enter text: NAME

CREATING THE PROJECTION SYMBOL

Command: circleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]: 235,147.5Specify radius of circle or [Diameter] <25.0000>: DSpecify diameter of circle <50.0000>: 30

Command: circleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]: 235,147.5Specify radius of circle or [Diameter] <15.0000>: DSpecify diameter of circle <30.0000>: 15 ENTER

Command: LINESpecify first point: 260,162.5Specify next point or [Undo]: @0,-30Specify next point or [Undo]: @40,7.5Specify next point or [Close/Undo]: @0,15Specify next point or [Close/Undo]: @-40,7.54Specify next point or [Close/Undo]: Close

RESULT:Thus the following title block drawing was created successfully using

Auto Cad Software.

CREATION OF 3D MODEL OF V BLOCK

AIM: To draw the 3d view of v block using Auto CAD Software

Command: vpointSpecify a view point or [Rotate] <display compass and tripod>: 1,-1,1Regenerating model.

Command: shademodeEnter option [2D wireframe/3D wireframe/Hidden/Flat/Gouraud/fLat+edges/gOuraud+edges] <Flat+Edges>: 3d

Command: lineSpecify first point :pick any point Specify next point or [Undo]: @30,0,0Specify next point or [Undo]: @0,0,20Specify next point or [Close/Undo]: @-5,0,0Specify next point or [Close/Undo]: @-10,0,-10Specify next point or [Close/Undo]: @-10,0,10Specify next point or [Close/Undo]: @-5,0,0Specify next point or [Close/Undo]: c

Command: regionSelect objects: Specify opposite corner: 6 foundSelect objects:1 loop extracted.1 Region created.

Command: extEXTRUDESelect objects: select objectSpecify height of extrusion or [Path]: 30Specify angle of taper for extrusion <0>: 0 ENTER

RESULT: Thus the 3D view of V block drawing was successfully created using

Auto CAD Software

CREATION OF 3D MODEL OF BASE OF MIXEE

AIM: To draw the 3d view of base of mixee using Auto CAD Software



Command: lineSpecify first point :pick any point Specify next point or [Undo]: @0,95,0Specify next point or [Undo]: @0,-10,65Specify next point or [Close/Undo]: @0,-30,0Specify next point or [Close/Undo]: @0,-15,-45Specify next point or [Close/Undo]: @0,-30,0Specify next point or [Close/Undo]: c

Command: regionSelect objects: Specify opposite corner: 6 foundSelect objects: all objects1 loop extracted.1 Region created

Command: ext EXTRUDESelect objects: select objectSpecify height of extrusion or [Path]: 40Specify angle of taper for extrusion <0>: 0 ENTER

Command: CircleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]:pick any pointSpecify radius of circle or [Diameter] : DSpecify diameter of circle <70.0000>: 15 ENTER

Command: extEXTRUDESelect objects: select objectSpecify height of extrusion or [Path]: 20 Specify angle of taper for extrusion <0>: 0 ENTER

Command: SubtractSelect objects: select the objectSelect objects: pick the circleSelect objects: select the object

RESULT: Thus the 3D view of base of mixee drawing was successfully created using

Auto CAD Software.

CREATION OF CUBIC SPLINE

AIM: To draw the cubic spline using Auto CAD Software



Command: PLINESpecify start point: @10,0Current line-width is 0.0000Specify next point or [Arc/Halfwidth/Length/Undo/Width]: @0,10Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @-20,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-20Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-20Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @30,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,30Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @-40,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-40Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @50,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,50Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @-60,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @60,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-60Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @70,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,70Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @-80,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-80Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @90,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: ENTER

RESULT:Thus the cubic spline drawing was successfully created using

Auto CAD Software.

CREATION OF PARABOLA

AIM: To draw the parabola using Auto CAD Software



Command: SPLINESpecify first point or [Object]: pick any point p1Specify next point : pick any point p2Specify next point or [Close/Fit tolerance]: pick any point p3Specify next point or [Close/Fit tolerance] : ENTERSpecify start tangent: ENTERSpecify end tangent: ENTER

RESULT: Thus the cubic spline drawing was successfully created using

Auto CAD Software

ISOMETRIC DRAWING

AIM: To Draw the Isometric Drawing Using Auto CAD Software

Command: snapSpecify snap spacing or [ON/OFF/Aspect/Rotate/Style/Type] <0.5000>: styleEnter snap grid style [Standard/Isometric] <S>: isometricSpecify vertical spacing <0.5000>: ENTER

Command: lineSpecify first point:Specify next point or [Undo]: 90Specify next point or [Undo]: 120Specify next point or [Close/Undo]: 70Specify next point or [Close/Undo]: 20Specify next point or [Close/Undo]: 90Specify next point or [Close/Undo]: 120Specify next point or [Close/Undo]: 70Specify next point or [Close/Undo]: close

Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 60

Command: copySelect the object: select the lineSpecify base of displacement: pick the point ENTER

RESULT:Thus the isometric object drawing was successfully created using

Auto CAD Software

3D VIEW OF CONE

AIM: To draw the 3d view of cone using Auto CAD Software




Command: coneSpecify center point for base of cone or [Elliptical] <0,0,0>: pick any pointSpecify radius for base of cone or [Diameter]: 50Specify height of cone or [Apex]: 70 ENTER

RESULT:Thus the 3D view of cone drawing was successfully created using

Auto CAD Software

3D VIEW OF CYLINDER

AIM: To draw the 3d view of cylinder using Auto CAD Software




Command: coneSpecify center point for base of cone or [Elliptical] <0,0,0>: pick any pointSpecify radius for base of cone or [Diameter]: 30Specify height of cone or [Apex]: 100 ENTER

RESULT:Thus the 3D view of cylinder drawing was successfully created using

Auto CAD Software

3D VIEW OF HEXAGONAL PRISM

AIM: To draw the 3d view of hexagonal prism using Auto CAD Software




Command: polygonEnter number of sides <4>: 6Specify center of polygon or [Edge]: pick any pointEnter an option: ISpecify radius of the circle: 35

Command: extEXTRUDESelect objects of extrude: select the objectSpecify height of extrusion or [Path]: 70Specify angle of taper for extrusion <0>: 0 ENTER

RESULT:Thus the 3D view of hexagonal prism drawing was successfully created

using Auto CAD Software

SECTIONAL VIEW OF CYLINDER

AIM: To draw the sectional view of cylinder using Auto CAD Software



Command: CircleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]: pick any pointSpecify radius of circle or [Diameter] : DSpecify diameter of circle <70.0000>: 50 ENTER

Command: LineSpecify first point: pick any point with respect to circleSpecify next point or [Undo]: @50<0Specify next point or [Undo]: @70<90Specify next point or [Close/Undo]: @50<180Specify next point or [Close/Undo]: Close

Command: OffsetSpecify offset distance or [Through] <25.0000>:14Select object to offset or <exit>: LINE 1Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: ENTER

Command: LineSpecify first point: pick any point with respect to offset lineSpecify next point or [Undo]: both corners ENTER

Command: HatchCommand: hatchSelect internal point: pick points ENTER

RESULT:Thus the sectional view of cylinder was successfully created using Auto

CAD Software

SECTIONAL VIEW OF CONE

AIM: To draw the sectional view of cone using Auto CAD



Command: CircleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]:pick any pointSpecify radius of circle or [Diameter] : DSpecify diameter of circle <70.0000>: 35 ENTER

Command: LineSpecify first point: pick any point with respect to circleSpecify next point or [Undo]: @35<0Specify next point or [Undo]: @42<108Specify next point or [Close/Undo]: Close


Command: LineSpecify first point: pick any point with respect to offset lineSpecify next point or [Undo]: both corners ENTER

Command: CircleBy using three points method find the diameter value and draw the circle

Command: HatchCommand: hatchSelect internal point: pick points ENTER

RESULT:Thus the sectional view of cylinder was successfully created using

Auto CAD Software

2D VIEW OF V BLOCK

AIM: To draw the 2d view of following v block (front view, top view and side

view) using Auto CAD Software



FRONT VIEW

Command: LineSpecify first point: pick any pointSpecify next point or [Undo]: @5<180Specify next point or [Undo]: @20< 270Specify next point or [Undo]: @30<0Specify next point or [Undo]: @20<90Specify next point or [Undo]: @5<180Specify next point or [Close/Undo]: Close

Command: LineSpecify first point: (SELECT END 1)Specify next point or [Undo]: @14.1<315 ENTER

Command: LineSpecify first point: (SELECT END 2)Specify next point or [Undo]: @14.1<225 ENTER

TOP VIEW

Command: LineSpecify first point: pick any point with reference to front viewSpecify next point or [Undo]: @30<0Specify next point or [Undo]: @30<270Specify next point or [Undo]: close


Command: OffsetSpecify offset distance or [Through] <25.0000>:10Select object to offset or <exit>: LINE 2Specify point on side to offset: → RIGHT SIDESelect object to offset or <exit>: ENTER

SIDE VIEW

Command: LineSpecify first point: pick any point with reference to front viewSpecify next point or [Undo]: @30<0Specify next point or [Undo]: @20<90Specify next point or [Undo]: @30<180Specify next point or [Undo]: close

Command: OffsetSpecify offset distance or [Through] : 10Select object to offset or <exit>: SELECT LINE Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: ENTER

Command: TextSpecify starting point: pick any point Specify the height: 5Type the text: front view, top view, side view

RESULT: Thus the 2D view of V block drawing was successfully created using

Auto CAD Software

2D VIEW OF BASE OF MIXEEAIM:

To draw the 2d view of following v block (front view, top view and side view) using Auto CAD Software



FRONT VIEW

Command: LineSpecify first point: pick any pointSpecify next point or [Undo]: @95<0Specify next point or [Undo]: @65< 90Specify next point or [Undo]: @10<180Specify next point or [Undo]: @30<180Specify next point or [Close/Undo]: ENTER

Command: LineSpecify first point: pick any pointSpecify next point or [Undo]: select corner 1Specify next point or [Undo]: @20< 90Specify next point or [Undo]: @10<0Specify next point or [Undo]: @30< 0 ENTER

Command: LineSpecify first point: select corner ASpecify next point or [Undo]: select corner B ENTER

Command: LineSpecify first point: select corner CSpecify next point or [Undo]: select corner D ENTER

Command: EraseSpecify first point: pick any pointSpecify next point or [Undo]: Remove Unwanted LinesCommand: LineSpecify first point: select mid pointSpecify next point or [Undo]: @20<270 ENTER

Command: OffsetSpecify offset distance or [Through] :7.5Select object to offset or <exit>: SELECT LINE Specify point on side to offset: →RIGHT SIDE

Command: OffsetSpecify offset distance or [Through] :7.5Select object to offset or <exit>: SELECT LINE Specify point on side to offset: →RIGHT SIDE

Command: LineSpecify first point: select corner GSpecify next point or [Undo]: ENTER

TOP VIEW

Command: LineSpecify first point: pick any point with reference to front viewSpecify next point or [Undo]: @95<0Specify next point or [Undo]: @40< 270Specify next point or [Undo]: @95<180Specify next point or [Undo]: close

Command: OffsetSpecify offset distance or [Through] :10Select object to offset or <exit>: SELECT LINE Specify point on side to offset: →RIGHT SIDE



Command: OffsetSpecify offset distance or [Through] :10Select object to offset or <exit>: SELECT LINE Specify point on side to offset: ←LEFT SIDE

Command: circleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]:pick center pointSpecify radius of circle or [Diameter] <35.0000>: 75 ENTER

SIDE VIEW

Command: LineSpecify first point: pick any point with reference to front viewSpecify next point or [Undo]: @40<0Specify next point or [Undo]: @65< 90Specify next point or [Undo]: @40<180Specify next point or [Undo]: close

Command: TextSpecify starting point: pick any point Specify the height: 5Type the text: front view, top view, side view

RESULT: Thus the 2D view of base of mixee drawing was successfully created using

Auto CAD Software

CREATION OF STEEL TRUSS

AIM:To create the steel truss using AutoCAD.

Command: LIMITSReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <420.0000,297.0000>: 500,500

Command: ZOOMSpecify corner of window, enter a scale factor (nX or nXP), or[All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: ALLRegenerating model.

To draw B1Command: lineSpecify first point:Specify next point or [Undo]: 320Specify next point or [Undo]: 5Specify next point or [Close/Undo]: close

To draw C1Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 3Specify next point or [Undo]: 65Specify next point or [Undo]: 3Specify next point or [Undo]: 65Specify next point or [Close/Undo]: close




To draw T1Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 182Specify next point or [Undo]: 3Specify next point or [Undo]: 182Specify next point or [Undo]: 3Specify next point or [Close/Undo]: close

Command: rotateSelect objects: select T1Specify base point: pick the point CSpecify rotation angle or [Reference]: 18Specify next point or [Close/Undo]: close

To draw S1Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 66Specify next point or [Undo]: 3Specify next point or [Undo]: 66Specify next point or [Undo]: 3Specify next point or [Close/Undo]: close

Command: rotateSelect objects: select S1Specify base point: pick right sideSpecify rotation angle or [Reference]: - 46Specify next point or [Close/Undo]: close





To connect C1 to B1Command: C1 to B1Select object: C1Specify base point: C1(corner point)Specify second point: B1(point)

To connect T1 to C1Command: moveSelect object: C1Specify base point: T1(corner point)Specify second point: C1(corner point)Mirroring the object

Command: mirrorSelect objects: select allSpecify first point of mirror line: select line (point)Specify second point of mirror line: select line (point)Delete source objects? [Yes/No] <N>: no

RESULT:Thus the steel truss is perfectly created using AutoCAD software.

RESIDENTIAL BUILDING PLAN

AIM:To create the plane of residential building plan using AutoCAD.

Command: LIMITSReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <420.0000,297.0000>: 500,500

Command: ZOOMSpecify corner of window, enter a scale factor (nX or nXP), or[All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: ALLRegenerating model.

Command: lineSpecify first point: @60,150Specify next point: @90,0Specify next point: @0,-110Specify next point: @-46,0Specify next point: @-30,0Specify next point: @-14,10Specify next point or [Close/Undo]: close

Command: lineSpecify first point: @61,149Specify next point: @88,0Specify next point: @0,-108Specify next point: @-44,0Specify next point: @-28,0Specify next point: @-0,8Specify next point or [Close/Undo]: close

To draw W-C blockCommand: lineSpecify first point: @63,147Specify next point: @12,0Specify next point: @0,-10Specify next point: @-12,0Specify next point or [Close/Undo]: close

To draw both blockCommand: lineSpecify first point: @63,136Specify next point: @12,0Specify next point: @0,-18Specify next point: @-12,0Specify next point or [Close/Undo]: close

To draw passage blockCommand: lineSpecify first point: @77,147Specify next point: @38,0Specify next point: @0,-28Specify next point: @-38,0Specify next point or [Close/Undo]: close

To draw kitchen blockCommand: lineSpecify first point: @147,147Specify next point: @0,-2Specify next point: @-31,0Specify next point: @-12,0Specify next point or [Close/Undo]: close

To draw living room blockCommand: lineSpecify first point: @63,116Specify next point: @42,0Specify next point: @0,-58Specify next point: @-42,0Specify next point or [Close/Undo]: close

To draw the windows-ICommand: lineSpecify first point: @63,64Specify next point: @-9,0Specify next point: @0,15Specify next point: @9,0Specify next point or [Close/Undo]: close

To draw the windows-IICommand: lineSpecify first point: @126,147Specify next point: @0,9Specify next point: @12,0Specify next point: @9,0Specify next point or [Close/Undo]: close

RESULT:Thus the plane of the residential building is successfully created using

AutoCAD software.

Date post:	26-Jan-2016
Category:	Documents
Upload:	vijayakumar
View:	14 times
Download:	0 times

Cad Manual

Documents