CAD Standards 1
UNIVERSITY OF STELLENBOSCH
FACILITIES MANAGEMENT DEPT
CAD Standards
FOR CONSULTANTS
FOR STELLENBOSCH UNIVERSITY CONSULTANTS
K.W.Matthew Manager: Architectural Design Office
[email protected] – 021 808 4653
June 2007 - Revised July 2009
Revised June 2010
CAD Standards 2
Contents Page
1. Introduction .................................................................................................................................... 4
1.1 Background .............................................................................................................................. 4
1.2 Stellenbosch University Title Blocks.......................................................................................... 6
1.3 Editing Title Blocks ................................................................................................................... 7
1.4 Editing Text Properties ............................................................................................................. 7
1.5 Editing Title Block Entites ......................................................................................................... 8
1.6 Basic list of definitions and acronyms ....................................................................................... 9
2 Quick Guide for CAD Draftspersons ........................................................................................... 10
3 General Requirements ................................................................................................................. 11
3.1 Conditions of Compliance ....................................................................................................... 11
3.2 Drawing Transmittal Requirements ......................................................................................... 11
3.3 Available Information .............................................................................................................. 13
4 CAD File Format Requirements ................................................................................................... 14
4.1 General File Requirements ..................................................................................................... 14
4.2 Model Space, Layouts and External References ..................................................................... 14
4.3 Layer Naming ......................................................................................................................... 15
4.4 Menu Settings ........................................................................................................................ 15
4.5 Line Types ............................................................................................................................. 15
4.6 Font Styles ............................................................................................................................. 15
4.7 Symbols/Blocks ...................................................................................................................... 15
4.8 Drawing Units ......................................................................................................................... 16
4.9 Colour & Plotting Settings ....................................................................................................... 16
5 Special Requirements .................................................................................................................. 18
5.1 Space Inventory Requirements ............................................................................................... 18
5.2 Feature Surveys ..................................................................................................................... 18
CAD Standards 3
5.3 Underground Services ............................................................................................................ 19
6 APPENDIX A ................................................................................................................................. 21
6.1 Cover Sheet ........................................................................................................................... 21
6.2 Document Transmittal Form ................................................................................................... 22
6.3 Drawing Lists (US Tekeningnommers) .................................................................................... 23
6.4 Drawing Lists 2nd Page (US Tekeningnommers) .................................................................... 24
6.5 Standard Layer Names........................................................................................................... 25
7 APPENDIX B ................................................................................................................................. 37
7.1 Underground Services Unique Information ............................................................................. 37
8 APPENDIX C ................................................................................................................................. 38
8.1 Underground Services Unique Entity Codes ........................................................................... 38
8.2 Example – Underground Storm Water CAD File ..................................................................... 39
CAD Standards 4
1. Introduction
1.1 Background
AutoCAD is used in the maintenance, design and facilities management of buildings
and grounds in conjunction with other packages including, AutoCAD Map, MS Access,
ARCHIBUS, and AutoManager Workflow.
In this document the requirements for the AS BUILT drawings are outlined to obtain a
high quality uniform set of documents that can easily be digitally archived and
implemented into the buildings facility management system.
All queries relating to the CAD Standards should be directed to the Manager:
Architectural Design Office, Facilities Management Department, University of
Stellenbosch. Phone: (021) 808 4653 Fax: (021) 808 4299. E-mail: [email protected]
To be able to achieve a consistent standard regarding CAD documents generated by
consultants who are appointed to produce projects for the University, a complete set of
standard templates are made available to be used by the consultants.
These title sheets contain all the settings and standards needed for conformity purposes
such as:
o The basic title sheet layout to which the consultant is to add his unique name
block and ISO naming and numbering procedure.
o The layers needed for all disciplines divided into the following sections:
Architectural and Structural
Existing Architectural and Structural
Audio Visual
Building Management Systems
CAD Standards 5
Data and Communications
Electrical
Essential Services
Facilities Management
General
Hydraulic
Mechanical and Lifts
Security
Survey and Landscaping
Underground Services
o The text and text sizes
o The dimension settings
o The scaling settings for the following scales (1:1, 1:2, 1:5, 1:10, 1:20, 1:25, 1:50,
1:100, 1:200, 1:500 and 1:1000)
Consultants are strongly urged not to add to the layers as supplied unless absolutely
necessary.
CAD Standards 6
1.2 Stellenbosch University Title Blocks
The standard Stellenbosch University Title blocks are available for the following
sizes...... A0, A1, A2, A3, A4 landscape and A4 portrait. Title blocks are to be inserted
un-exploded at co-ordinates 0,0,0 into the Paper Space layout and contain the following
the following attributes.....
Ref Attribute Name Tag Description
1
Title Line 1 Title-1 The length of text string that is entered into
these two lines of the attributes are
determined by the space available Title Line 2 Title-2
2
Project Line 1 Project-1 The length of text string that is entered into
these two lines of the attributes are
determined by the space available Project Line 2 Project -2
3 Drawn By Drawn Initials of drawing creator
4 Checked By Checked Initials of drawing checker
5 Date Date Date drawing created in DD/MM/YYYY
format
6 Scale Scale The drawing scale in 1:XXX format
7 Building Name Bldname
The length of text string that is entered into
this line of the attribute is determined by
the space available
8 Building Reference Bld Maximum 3 characters XXX format
9 Drawing Number Draw-1
Drawing Number XX/XXX/XXX/U format
as per “Standard and “As Built”
requirements”.
10 Revision Number Rev Revision Number
CAD Standards 7
Stellenbosch University
Title Block Attribute Reference
1.3 Editing Title Blocks
Editing attributes in AutoCAD, use the DDATTE (Dialog
Attribute Editor), Select block reference: (select the Title
block), the following AutoCAD dialog box appears ....
Enter the valid information as required and click “OK” and the
Title Block updates.
1.4 Editing Text Properties
When entering information into the attribute dialogue box,
text strings might sometimes be long for the space provided
and you might have to change the text height of the attribute,
you will have to “Double Click” on the Title Block and the
following AutoCAD dialog box appears ....
CAD Standards 8
For example, we need to change the height of the Building Name string, highlight the
BLDNAME attribute and click on Text Options and the following AutoCAD dialog box
appears .....
Change the text height, or width factor and click “OK” twice to update your Title Block.
1.5 Editing Title Block Entites
When wanting to change the rotation angle of the north sign, highlight the Title Block,
“Right click” and select “Block Editor”, (or type BEDIT & select NORTH LEAF & rotate)
you will now be in the Block Editor, zoom to the “North Sign”, rotate the “North Sign” to
required angle.
Complete all changes and update the TitleBlock by clicking on “Close Block Editor”
and click on “Yes” to save changes.
CAD Standards 9
1.6 Basic list of definitions and acronyms
AutoCAD AutoCAD 2000 or later, copyright Autodesk.
AS-BUILT Measured and revised drawings documenting the full extent of completed
building works.
SAMG South African Map Grid.
SAHD South African Height Datum.
DWG Default AutoCAD drawing file format.
MODEL SPACE Defined drawing space in AutoCAD
PAPER SPACE Defined drawing space in AutoCAD for placing title sheets etc.
LAYOUT Defined drawing space in AutoCAD for placing title sheets etc
XREF An external drawing file that is referenced into the main drawing.
BIND An AutoCAD command that allows all external reference files to become a
BLOCK in the CAD file.
LAYER Electronic drawing sheet within a drawing file upon which data can be drawn
and manipulated. A layer can be turned on or off as required.
BYLAYER Settings of line types and colours for specified entities.
PURGED AutoCAD command to delete any entity information that is not being used in the
CAD file.
BLOCK A subordinate drawing file within the main drawing file.
EXPLODE AutoCAD command to break a subordinate drawing file into separate entities
within the main drawing file.
BASE An AutoCAD command that sets the insertion point of drawings when used as a
BLOCK.
CAD Standards 10
2 Quick Guide for CAD Draftspersons
This section is a quick guide for draftspersons that edit drawings for the contractor or
consultant. It summarises the basic elements that are to be adhered to when submitting
the "As-Built" drawings to the Facilities Management Department. This is not a
comprehensive listing but will help in ensuring drawings will be accepted. If drawing files
do not meet these basic criteria they will not be accepted.
The basic requirements are:
The CAD files shall be in AutoCAD 2000 file format and have the following conditions met
o One drawing unit = one millimetre
o Use fonts and line type files supplied with standard installation of AutoCAD
o Plot style table to be supplied.
o No external references to be used. (Xrefs shall be bound)
o Files shall be purged.
o There shall be one AutoCAD file per completed drawing (hard copy)
identical to the hard copy.
o Multiple drawings shall not be contained in one AutoCAD file.
o Drawing entities shall be in model space.
The documentation to be supplied should include:
o Building Number (building request number) as provided by the Building Data
Administrator, on each title sheet of the drawing.
o Marked with "AS BUILT" on each title sheet of the drawing.
o Marked with correct DATE on each title sheet of the drawing.
o Marked with correct REVISION numbers on each title sheet of the drawing.
CAD Standards 11
All computer files (DWG and PDF) shall be provided on a DVD or up-loaded on the FTP
website with a full size hard copy to the Building Data Administrator: Architectural
Design Office. Contact details: 808 9167 ([email protected])
www.sun.ac.za/sunprojects
3 General Requirements
3.1 Conditions of Compliance
All consultants and contractors are required to meet the specifications of the CAD
Standards set by the Planning and Development unit, Facilities Management, University
of Stellenbosch, as part of their conditions of appointment.
The University of Stellenbosch Planning and Development Unit provides
consultants/contractors with copies of the Stellenbosch University CAD files for
reference only and accepts no liability for their accuracy for purposes of building
design or construction. All consultants/contractors are required to carry out the
normal standard of site investigations as required by their profession and in
accordance with their conditions of contract.
The consultant/contractor shall provide the Planning and Development Unit with "As-
Built" AutoCAD drawings as specified in the Standards Manual, no later than one
month after practical completion.
3.2 Drawing Transmittal Requirements
All "As-Built" drawings are to be marked in an obvious fashion with the text "As Built" on
the Cad files as well as hard copies of the drawings. These drawings shall be
documentation of the built structure after building work is completed.
All drawings should have the B Number (Building Number) written on the Title sheet.
The B number is the number generated by the University for that specific building and
can be acquired through the Building Data Administrator.
CAD Standards 12
All digital data shall be sent to the University with a cover sheet and an information
sheet attached to it for easier reference and cataloguing. Copies of cover sheet and file
information sheet are supplied in Appendix A.
One set of printed hard copies shall be issued to the Planning and Development Unit
with the AutoCAD file information. The maximum title sheet size to be used for printed
hard copy drawings shall be A1 according to ISO standards.
One set of "As-Built" information per project is required. Multiple contracts or building
requisitions shall not be combined into one set of "As-Built" documentation.
When submitting the CAD files of the "As-Built" drawings, the CAD file names shall be
accurately named to identify the project.
The CAD file name shall include a prefix and suffix combined from the information
described below:
-Drawing Focus:
A letter identifying the drawing discipline according to the following:
A Architectural
S Structural
M Mechanical & Lifts
E Electrical
H Hydraulic
DC Data & Communications
S Survey, Landscape & Grounds
U University of Stellenbosch Architectural Services
Prefixes:
S Stellenbosch Campus
T Tygerberg Campus
B Bellville Park Campus
M Mariendahl Experimental Farm
W Welgevallen Experimental Farm
CAD Standards 13
-Building Number:
The building number is a unique integer that can be obtained from the Architectural
Design Office.
-Example 1:
SA/182/102/U/3
The prefix SA 182 represents a Stellenbosch Campus administrative building drawing
for building 182, the suffix 102 is the unique drawing number, U indicates that it was
generated by the University of Stellenbosch Architectural Services office and 3 indicates
the revision status.
-Example 2:
SA/182/102/M/3
The prefix SA 182 represents a Stellenbosch Campus administrative building drawing
for building 182, the suffix 102 is the unique drawing number, M indicates that it was
generated by a Mechanical consultant and 3 indicates the revision status.
3.3 Available Information
Information on the University of Stellenbosch CAD standards is available upon request.
The information includes AutoCAD prototype drawings, line type files, font files,
dimension styles files, menu files and plot file settings. It is recommended this
information be requested prior to commencing the “as built” documentation process.
The complete CAD Standards document with drawing register pages, as well as all title
block sheet templates (containing layers, font styles and sizes, dimension styles) and
the plot style file is available on http://www.sun.ac.za/sunprojects.
CAD Standards 14
4 CAD File Format Requirements
4.1 General File Requirements
The consultant/contractor shall ensure that all CAD files conform to the following:
All CAD files are to be recorded on CD, for transmittal to the Architectural Services
Office in AutoCAD 2000 file format.
There shall be only one CAD file for each individual drawing; multiple drawings saved to
one CAD file will not be accepted. Also one drawing with many CAD files will not be
accepted.
All files shall be PURGED prior to being transmitted to the Architectural Services Office.
Each CAD file shall be saved with layer "0" set as the current layer.
All CAD files of building floor plans shall have BASE set to "0,0,0" and the floor plans
drawn to the same grid coordinates on each CAD file.
All entities within the drawing file shall have the colours and line types set to BYLAYER.
4.2 Model Space, Layouts and External References
Where the project is too large for the title sheet, the drawing is to be split only for
plotting in layout or PAPER SPACE. All CAD drawings shall be drawn as one
continuous and uniform plan in MODEL SPACE.
All drawing entities for each drawing are to be contained in one file, without the use of
external reference files. If drawings were originally created with external reference files,
the AutoCAD BIND command shall be used to include the external reference file as part
of the main file. The BLOCK created by this command shall be EXPLODED.
Layer names from external reference drawings shall conform to the layer naming
requirements as specified in section 3.3. Any layers that have been inserted to a
drawing after an external reference has been bound and exploded shall be renamed to
remove the external reference file name prefix off the layer names.
All drawing entities are to be drawn in MODEL SPACE on the CAD files; drawing title
sheet information will be accepted. This can include scale bars, north points, general
notes.
CAD Standards 15
4.3 Layer Naming
Layer-names are included in each title block template. Standard Layer Table List all
the standard layer names that shall be used for "As-Built" drawing files. The
consultant/contractor shall endeavour to use these layer names in this table in
preference to any other layer names.
4.4 Menu Settings
The drawing shall be submitted either with the AutoCAD menu set to the standard
acad.mnu file or as supplied by the Architectural Design Office.
4.5 Line Types
All line types shall be set to BYLAYER and only standard line types provided by the
standard installation of AutoCAD in the standard acad.lin file or as supplied by the
Architectural Design Office shall be used.
All documentation of Under Ground Services according to section 4.3 shall use
customised line types as supplied by the Architectural Design Office. These are
available upon request.
4.6 Font Styles
All fonts used in the CAD file shall be SHX type fonts as supplied by the standard
installation of AutoCAD. True type fonts will not be accepted. If text is used to represent
an object then the insertion point must be "middle centre" justified.
4.7 Symbols/Blocks
All blocks within a CAD file shall have their entities drawn on layer 0 and inserted in the
discipline layer so that all BLOCKS will be shown together when required.
All grounds, underground services, and landscape elements shall be from the standard
blocks library as supplied upon request from the Architectural Design Office. Where
CAD Standards 16
blocks are unavailable for the required device or structure, reference shall be made to
applicable South African standards for the correct symbol.
Where a new block is defined, the insertion point shall be in the middle of the block
unless inapplicable.
Blocks for fire detection devices shall be in accordance with the South African standards
4.8 Drawing Units
All drawings shall be drawn at a scale of one drawing unit = 1 millimetre.
4.9 Colour & Plotting Settings
The plotting settings for AutoCAD shall be set to colour-dependent plot style tables
(CTB) for AutoCAD 2000 and all entities shall have colour set to BYLAYER. The
following is a specification of the plotting configuration used by the Architectural Design
Office at University of Stellenbosch. All consultants and contractors are to adopt this
standard for "As-Built" drawings.
N.B. Electrical and Mechanical consultants are permitted to use colour plot settings for
design and construction purposes only, but “as-builts” must be legible and supplied in
monochrome.
CAD Standards 17
Colour and Plotting Setting
Colour No. Thickness
/Fading Colour No.
Thickness
/Fading Colour No.
Thickness
/Fading Colour No.
Thickness
/Fading
1 0.1 65 0.25 129 0.25 193 0.25
2 0.35 66 0.25 130 0.25 194 0.25
3 0.15 67 0.25 131 0.25 195 0.25
4 0.05 68 0.25 132 0.25 196 0.25
5 0.05 69 0.25 133 0.25 197 0.25
6 0.2 70 0.1 134 0.25 198 0.25
7 0.25 71 0.25 135 0.25 199 0.25
8 0.05 72 0.25 136 0.05 200 0.25
9 0.13 73 0.25 137 0.25 201 0.25
10 0.5 74 0.25 138 0.25 202 0.25
11 0.7 75 0.25 139 0.25 203 0.25
12 0.18 76 0.25 140 0.25 204 0.25
13 0.2 77 0.25 141 0.25 205 0.25
14 0.25 78 0.25 142 0.25 206 0.25
15 0.25 79 0.25 143 0.25 207 0.25
16 0.25 80 0.25 144 0.25 208 0.25
17 0.25 81 0.25 145 0.25 209 0.25
18 0.25 82 0.25 146 0.25 210 0.25
19 0.25 83 0.25 147 0.25 211 0.25
20 0.25 84 0.25 148 0.25 212 0.25
21 0.1 85 0.25 149 0.25 213 0.25
22 0.25 86 0.25 150 0.1 214 0.25
23 0.25 87 0.25 151 0.25/10% 215 0.25
24 0.25 88 0.25 152 0.25 216 0.25
25 0.25 89 0.25 153 0.25 217 0.25
26 0.25 90 0.25 154 0.25 218 0.25
27 0.25 91 0.25 155 0.25 219 0.25
28 0.25 92 0.25 156 0.25 220 0.25
29 0.25 93 0.25 157 0.25 221 0.25
30 0.25 94 0.25 158 0.25 222 0.25
31 0.13 95 0.25 159 0.25 223 0.25
32 0.25 96 0.25 160 0.25 224 0.25
33 0.25 97 0.25 161 0.25 225 0.25
34 0.25 98 0.25 162 0.25 226 0.25
35 0.25 99 0.25 163 0.25 227 0.25
36 0.25 100 0.25 164 0.25 228 0.25
37 0.25 101 0.25 165 0.25 229 0.25
38 0.25 102 0.25 166 0.25 230 0.25
39 0.25 103 0.25 167 0.25 231 0.25
40 0.25 104 0.25 168 0.25 232 0.25
41 0.13 105 0.25 169 0.25 233 0.25
42 0.35 106 0.25 170 0.25 234 0.25
43 0.18 107 0.25 171 0.25/25% 235 0.25
44 0.25 108 0.25 172 0.25 236 0.25
45 0.35 109 0.25 173 0.25 237 0.25
46 0.5 110 0.25 174 0.25 238 0.25
47 0.7 111 0.25 175 0.25 239 0.25
48 0.25 112 0.25 176 0.25 240 0.25
49 0.25 113 0.25 177 0.25 241 0.25
50 0.15 114 0.25 178 0.25 242 0.25
51 0.13 115 0.25 179 0.25 243 0.25
52 0.09 116 0.25 180 0.25 244 0.25
53 0.25 117 0.25 181 0.25 245 0.25
54 0.25 118 0.25 182 0.25 246 0.25
55 0.25 119 0.25 183 0.25 247 0.25
56 0.25 120 0.25 184 0.25 248 0.25
57 0.25 121 0.25 185 0.25 249 0.25
58 0.25 122 0.25 186 0.25 250 0.25
59 0.25 123 0.25 187 0.25 251 0.25
60 0.25 124 0.25 188 0.25 252 0.25
61 0.25 125 0.25 189 0.25 253 0.25
62 0.25 126 0.25 190 0.25 254 0.25
63 0.25 127 0.25 191 0.25 255 0.25
64 0.25 128 0.25 192 0.25 256 0.25
CAD Standards 18
5 Special Requirements
The following are special requirements for the Space Inventory, Feature Surveys,
Landscape and Underground Services documentation.
5.1 Space Inventory Requirements
o Polylines shall be drawn to outline the useable floor area for each area type
including rooms, circulation areas, external gross area and internal gross area
of each floor level. Refer to Appendix 1.D of the Space and Data
Management Office, University of Stellenbosch.
o Design Standards for method of measurement and definitions.
o All area polylines shall be closed polylines.
o All room numbers shall be clearly notated in MODEL SPACE, in 3.5mm
height text on each room layout.
o The useable floor area in square metres of each room shall be clearly notated
in MODEL SPACE, in 2.5mm height text on each room layout.
o The polylines shall be drawn on the correct layers as specified in Standard
Layer Table List.
5.2 Feature Surveys
All plans shall be orientated with North to the top of the screen. Where a campus survey
drawing is used there shall be NO rotation to the drawing.
All elements shall be surveyed in three coordinates (X,Y,Z) using only AMG and AHD.
Where available within the campus, a minimum of three benchmarks shall be used and
CAD Standards 19
tied to one another to check for any possible variation in the coordinates or RL. Where
no guaranteed benchmarks exist in the campus area, the contractor must place at least
three control points in the campus area by a qualified surveyor. The coordinates and
mapped positions of these control points must be submitted with the final work. The
control points must be placed in stable areas where there is little chance of them being
destroyed; those areas shall be coordinated with the Space and Data Management
Office.
Contours shall be displayed on all drawings at a suitable contour interval where
applicable.
Trees of a height of one metre or more shall be surveyed. The position of the tree shall
be surveyed as the middle of the trunk, measured at one metre above ground level.
All existing features shall be surveyed unless approval in writing is granted by Space
and Data Management Office, of the University of Stellenbosch. Only standard symbols
shall be used on the drawing and they can be obtained from the Space and Data
Management Office. With regard to site plans and service information, only information
supplied by registered land surveyors will be accepted for inclusion in the University
data base. Contact telephone number 021 808 4834.
5.3 Underground Services
All constructed underground services shall be mapped on the campus survey plan.
The investigation shall provide the following information for each service.
o The service location on plan together with an offset measurement from the
nearest building line.
o Material of pipe or conduit.
o Depth or cover to pipe, conduit or cable.
o Diameter of pipe or conduit.
o The reduced level on pit covers.
o The depth and exact location of pit, including the edges of pits.
CAD Standards 20
o The invert level of pipes or conduits converging on a pit.
o Documentation on the type of pit, material and depth of pit, type of lid and
state of repair of pit.
o In cases of array of conduits, the surveyor shall provide information on
which conduits are in service and which are not.
o All isolation valves to buildings or other set areas, this is to include valves
inside and outside buildings.
The contractor shall also detail all service entity information as specified in Appendix B.
The final documentation for underground services shall be provided in two formats
incorporating an AutoCAD drawing file and an Excel spreadsheet. To enable Excel
information to be associated with the correct service entity on the AutoCAD file, each
Excel record will have a unique entity code. The format for this code is in Appendix C.
The pit number for pits shall be the same as the unique entity code as specified above.
All abbreviations used in the documentation of the underground services must be fully
defined within the legend of all title sheets.
As an exception to section 3.2, underground service Cad files shall comprise of external
reference files. One AutoCAD CAD file for each service type surveyed.
The Space and Data Management Office, of the University of Stellenbosch is able to
provide records of known services on request.
CAD Standards 21
6 APPENDIX A
6.1 Cover Sheet
STELLENBOSCH UNIVERSITY
COVER SHEET
Job Title: ______________________________________________________________
Building Number: _______________ Building Name: __________________________
Br Number: ____________________ Drawings Completion Date: ________________
Company/Firm Name: ___________________________________________________
Contact Person: ________________________________________________________
Address: ______________________________________________________________
_____________________________________________________________________
Phone Number: ________________ Fax Number: ____________________________
E-mail address:_________________________________________________________
Drawing Discipline
Architectural Mechanical
Electrical Structural
Grounds / Landscape Underground Services
Hydraulic Survey
Attachments
Please find enclosed:
Disks (2 sets) Number of disks per set: ______________
Hard copies (1 set)
File Information Sheets
CAD Standards 22
6.2 Document Transmittal Form
UNIVERSITY OF STELLENBOSCH
DOCUMENT TRANSMITTAL FORM
Attention: _____________________________________________________________
Company/Firm: _________________________________________________________
Address: ______________________________________________________________
_____________________________________________________________________
Date: _________________
Building Number: _______________ Building Name: __________________________
Sender: _______________________ Contact Number: _________________________
Attachments: Fax Number: (021) 808 4299
Please Find Enclosed: Sent By:
DVD ROM (1 Set) Number of disks per set: _________ Picked up
Hard Copies (1 Set) Number of copies per set:_________ Post
Other: ________________________________________________ Courier
Other
DOCUMENT NO DOCUMENT DESCRIPTION
CAD Standards 23
6.3 Drawing Lists (US Drawing Numbers)
This is the only list that should be used for listing all project drawing documents generated as
well as to be included as the final “as built” register for the Building Data Administration
US DRAWING NUMBERS
BUILDING CODE: AA000
BUILDING NAME: ABC
LAST UPDATED: 10/10/2008 *DRAWING NOT ON SYSTEM
E = Electronic- S = Scanned- P = Hard Copy- E1 = Electronic, Hard Copy + PDF- E2 = Electronic + Hard Copy
E3 = Electronic +PDF- S1 = Scanned, Hard Copy + PDF- S2 = Scanned + Hard Copy- S3 = Scanned + PDF
PLAN REFERENCE DESCRIPTION CONSLT. NO. CAD NO.
E1
CAD Standards 24
6.4 Drawing Lists 2nd Page (US Drawing Numbers)
AA/000 PAGE 0
PLAN REFERENCE DESCRIPTION CONSLT. NO. CAD NO.
CAD Standards 25
6.5 Standard Layer Names
This is the only complete list of layers to be used. Any additional layers are discouraged. Note
that all the layers and layer protocols are included on each pro forma title sheet.
No. Discipline Name Description Linetype Thickness Color
1 0 Layer Creator - 0 Continuous 0.25 7
2
Architecture and
Structural
A_AccessHatch Architecture - Access to plant and ceiling spaces Continuous 0.05 8
3 A_BuildingOutline Architecture - Building outline Continuous 0.35 2
4 A_BuldingLine Architecture - Municipal building line ACAD_ISO06W100 0.10 1
5 A_BulkheadDecorative Architecture - Bulkhead Decorative Continuous 0.25 7
6 A_BulkHeadHatch Architecture - Bulkhead Hatch Continuous 0.25 171
7 A_BulkheadStructural Architecture - Structural bulkheads Continuous 0.15 3
8 A_CarSpace Architecture - Marked out car space Continuous 0.25 7
9 A_Ceiling Architecture - Reflected ceiling Continuous 0.15 3
10 A_Ceiling-Battens Architecture - Ceiling Battens Continuous 0.10 1
11 A_CeilingCornice Architecture - Ceiling Cornice Continuous 0.15 3
12 A_Chimney Architecture - Chimney Continuous 0.35 2
13 A_ChimneyFlues Architecture - Chimney Flues Continuous 0.25 15
14 A_Chimney-Hidden Architecture - Chimney Behind ACAD_ISO03W100 0.05 8
15 A_ColumnConcrete Architecture - Concrete Columns Continuous 0.35 2
16 A_ColumnSteel Architecture - Structural steel columns Continuous 0.20 6
17 A_Concrete Architecture - Concrete in plan and section Continuous 0.25 80
18 A_ConcreteBeam Architecture - Concrete Beam Continuous 0.25 7
19 A_ConcreteHatch Architecture - New concrete hatch Continuous 0.10 70
20 A_Door Architecture - Fixed panel doors Continuous 0.20 13
21 A_DoorAuto Architecture - Automatic door Continuous 0.20 13
22 A_DoorGlass Architecture - Glass door Continuous 0.50 4
23 A_DoorRoller Architecture - Roller door Continuous 0.20 13
24 A_Drainage Architecture - Drainage ACAD_ISO02W100 0.13 41
25 A_DrainageText Architecture - Drainage Text Continuous 0.13 31
26 A_DripTrays Architecture - Driptrays Continuous 0.20 6
27 A_EavesLine Architecture - Eaves line Continuous 0.10 1
28 A_Electrical Architecture - Electrical Continuous 0.18 43
29 A_ElectricalText Architecture - Electrical Text Continuous 0.13 31
30 A_Fascias Architecture - Fascias general Continuous 0.15 3
31 A_Fixture Architecture - Fixtures - fitting built-in Continuous 0.05 5
32 A_Flashing Architecture - Flashing Continuous 0.10 1
33 A_FloorCarpet Architecture - Carpet floor Continuous 0.15 3
34 A_FloorFurniture Architecture - Floor Furniture Continuous 0.35 2
CAD Standards 26
35 A_FloorFurniture-Above Floor Furniture - Above HIDDEN2 0.15 3
36 A_FloorFurniture-AdjustableFoot Floor Furniture - Adjustable Feet Continuous 0.13 9
37 A_FloorFurniture-Below Floor Furniture - Below DASHED2 0.05 8
38 A_FloorFurniture-Castors Floor Furniture - Castors Continuous 0.20 6
39 A_FloorFurniture-Castors-Below Floor Furniture - Castors Below HIDDEN2 0.05 8
40 A_FloorFurniture-Cupboards Floor Furniture - Cupboards Continuous 0.35 2
41 A_FloorFurniture-Cupboards-Below Floor Furniture - Cupboards Below DASHED2 0.05 8
42 A_FloorFurniture-Dim Floor Furniture - Dimensions Continuous 0.05 8
43 A_FloorFurniture-Dim-Detail Floor Furniture - Dimensions for Details Continuous 0.05 8
44 A_FloorFurniture-Elevation_1 Floor Furniture - Elevation-1 Continuous 0.25 40
45 A_FloorFurniture-Elevation_2 Floor Furniture - Elevation-2 Continuous 0.18 12
46 A_FloorFurniture-Elevation_3 Floor Furniture - Elevation-3 Continuous 0.10 70
47 A_FloorFurniture-Glass Floor Furniture - Glass Continuous 0.20 13
48 A_FloorFurniture-Glass-Hatch Floor Furniture - Glass Hatch Continuous 0.05 151
49 A_FloorFurniture-Handles and Locks Floor Furniture - Handles and Locks Continuous 0.10 1
50 A_FloorFurniture-Hatch Floor Furniture - Hatch Continuous 0.05 151
51 A_FloorFurniture-Neoprene Floor Furniture - Neoprene Continuous 0.25 7
52 A_FloorFurniture-Neoprene-Hatch Floor Furniture - Neoprene Hatch Continuous 0.05 151
53 A_FloorFurniture-Nuts and Bolts Floor Furniture - Nuts Bolts Screws and Washers Continuous 0.13 31
54 A_FloorFurniture-Plumping Floor Furniture - Plumping Continuous 0.05 5
55 A_FloorFurniture-Plumping-Below Floor Furniture - Plumping Below HIDDEN2 0.05 8
56 A_FloorFurniture-Sanitary Floor Furniture - Sanitary Continuous 0.05 5
57 A_FloorFurniture-Sanitary-Below Floor Furniture - Sanitary Below DASHED2 0.05 8
58 A_FloorFurniture-Seating Wall Floor Furniture - Seating Wall Continuous 0.25 141
59 A_FloorFurniture-Steel Floor Furniture - Steel Continuous 0.25 20
60 A_FloorFurniture-Steel-Below Floor Furniture - Steel Below HIDDEN2 0.10 21
61 A_FloorFurniture-Steel-Hatch Floor Furniture - Steel Hatch Continuous 0.05 151
62 A_FloorFurniture-Steel-Section Floor Furniture - Steel Section Continuous 0.13 31
63 A_FloorFurniture-Vents Floor Furniture - Vents Continuous 0.20 13
64 A_FloorFurniture-Welding Floor Furniture - Welding Continuous 0.70 11
65 A_FloorFurniture-Wood Floor Furniture - Wood Continuous 0.25 80
66 A_FloorFurniture-Wood-Below Floor Furniture - Wood Below DASHED2 0.13 9
67 A_FloorFurniture-Wood-Hatch Floor Furniture - Wood Hatch Continuous 0.05 151
68 A_FloorFurniture-Wood-Section Floor Furniture - Wood Section Continuous 0.13 41
69 A_FloorLine Architecture - Floor line/threshold etc. Continuous 0.15 3
70 A_FloorScreed Architecture - Floor Screed Continuous 0.20 6
71 A_FloorScreedHatch Architecture - Floor Screed Hatch Continuous 0.05 151
72 A_FloorSkirting Architecture - Floor Skirting Continuous 0.13 31
73 A_FloorText Architecture - Floor RLs and structure type and step heights Continuous 0.25 7
74 A_FloorTile Architecture - Floor Tile Continuous 0.15 3
75 A_FloorVinyl Architecture - Vinyl floor Continuous 0.15 3
CAD Standards 27
76 A_Foundation Architecture - Foundation Continuous 0.35 45
77 A_FoundationHatch Architecture - Foundation Hatch Continuous 0.13 9
78 A_Grid Architecture - Building grid ACAD_ISO10W100 0.25 191
79 A_GridCircle Architecture - Building grid circle ACAD_ISO10W100 0.25 191
80 A_GridText Architecture - Building grid text Continuous 0.25 255
81 A_GroundLine Architecture - Ground line Continuous 0.70 11
82 A_Gulley Architecture - Gulley Continuous 0.13 9
83 A_Gutter Architecture - Gutter - Box Gutter and RWP etc… Continuous 0.05 5
84 A_Levels Architecture - Floor levels ACAD_ISO05W100 0.25 254
85 A_Partition Architecture - Partition Continuous 0.20 6
86 A_PartitionGlass Architecture - Glass partition Continuous 0.05 4
87 A_PartitionHatch Architecture - Partition Hatch BATTING 0.10 1
88 A_Pergola Architecture - Pergola Continuous 0.15 3
89 A_PergolaAbove Architecture - Pergola Above HIDDEN2 0.15 3
90 A_PergolaSection Architecture - Pergola Section Continuous 0.18 43
91 A_Plaster Architecture - Plaster Continuous 0.05 8
92 A_PlasterHatch Architecture - Plaster Hatch Continuous 0.05 4
93 A_PlumbingFittings Architecture - Plumbing fitting built in Continuous 0.05 5
94 A_Roof Architecture - Roof Continuous 0.10 1
95 A_RoofCover Architecture - Roof Cover - Tiles etc….. Continuous 0.13 41
96 A_RoofHatch Architecture - Roof Hatch Continuous 0.13 9
97 A_RoofRafter Architecture - Roof rafter in Section Continuous 0.13 41
98 A_RoofSheet Architecture - Roof sheet Continuous 0.25 130
99 A_RoofSisolation Architecture - Sisolation ACAD_ISO04W100 0.50 46
100 A_RoofWallPlate Architecture - Roof wall plate in Section Continuous 0.25 40
101 A_SectionElevation_18 Architecture - Light elevation layer Continuous 0.18 12
102 A_SectionElevation_25 Architecture - Standard elevation layer Continuous 0.25 40
103 A_SectionElevation_35 Architecture - Medium elevation layer Continuous 0.35 42
104 A_SectionElevation_50 Architecture - Heavy elevation layer Continuous 0.50 10
105 A_SectionElevation_70 Architecture - Very heavy elevation layer Continuous 0.70 11
106 A_Signage Architecture - Signage equipment Continuous 0.25 15
107 A_SignageText Architecture - Signage text Continuous 0.25 7
108 A_Silicon Architecture - Silicon Continuous 0.25 7
109 A_SiliconHatch Architecture - Silicon Hatch Continuous 0.05 151
110 A_Stair Architecture - Internal stairs or ramps and steps Continuous 0.10 1
111 A_StairBalustrade Architecture - Railings and handrails etc…. Continuous 0.10 1
112 A_StairText Architecture - Stairs Text Continuous 0.13 31
113 A_SteelBeam Architecture - Structural beam member Continuous 0.10 1
114 A_SteelHatch Architecture - New steel hatching Continuous 0.05 150
115 A_StudWall Architecture - Stud wall Continuous 0.25 54
116 A_TimberHatch Architecture - New timber hatching Continuous 0.10 21
117 A_VentPipe Architecture - Vent Pipe Continuous 0.13 9
118 A_Veranda Architecture - Veranda ACAD_ISO03W100 0.15 3
CAD Standards 28
119 A_Void Architecture - Void space in structure ACAD_ISO03W100 0.25 7
120 A_WallBrick Architecture - Brick wall Continuous 0.35 42
121 A_WallCavity Architecture - Cavity-wall Continuous 0.10 1
122 A_WallColdRoom Architecture - Cold Room Walls Continuous 0.35 2
123 A_WallColdRoomHatch Architecture - Cold Room Wall Hatch BATTING 0.15 50
124 A_WallDemolish Architecture - Demolish walls ACAD_ISO03W100 0.35 42
125 A_WallHatch Architecture - New wall hatching Continuous 0.15 50
126 A_WallMisc Architecture - Wall miscellaneous Continuous 0.25 240
127 A_WallOpening Architecture - Wall Openings Arches and Hatches etc.... DASHED2 0.20 13
128 A_WallTile Architecture - Wall Tiles Hatch Continuous 0.15 50
129 A_WallTileBelow Architecture - Wall Tiles Below HIDDEN2 0.05 8
130 A_Window Architecture - Windows Continuous 0.10 1
131 A_WindowCill Architecture - Window cills Continuous 0.15 3
132
Existing Architecture
and Structural
A_X-Balustrade Existing - Balustrade Continuous 0.13 41
133 A_X-Balustrade-Hatch Existing - Balustrade-Hatch Continuous 0.05 151
134 A_X-BuildingElements Existing - Building elements Continuous 0.13 9
135 A_X-Ceiling Existing - Ceiling Continuous 0.13 9
136 A_X-Column-Brick Existing - Brick Column Continuous 0.10 1
137 A_X-Column-Concrete Existing - Column-Concrete Continuous 0.13 9
138 A_X-Column-Steel Existing - Column-Steel Continuous 0.20 13
139 A_X-Door Frame Existing - Door Frame Continuous 0.10 1
140 A_X-Doors Existing - Doors Continuous 0.10 1
141 A_X-FloorConcrete Existing – Floor Concrete Continuous 0.35 2
142 A_X-FloorConcrete-Hatch Existing – Floor Concrete Hatch Continuous 0.05 151
143 A_X-Furniture-Fixed Existing - Fixed Furniture Continuous 0.05 4
144 A_X-Ground Existing - Ground Continuous 0.05 5
145 A_X-Gulley Existing - Gulley Continuous 0.10 1
146 A_X-Machinery Existing - Machinery Continuous 0.20 6
147 A_X-Manhole Existing - Manhole Continuous 0.15 3
148 A_X-Partition Existing - Partitions Continuous 0.13 9
149 A_X-Ramp Existing - Ramp Continuous 0.25 7
150 A_X-Roof Existing - Roof Continuous 0.25 20
151 A_X-Roof-Hatch Existing - Roof Hatch Continuous 0.10 21
152 A_X-Sanitary Existing - Sanitary Continuous 0.25 14
153 A_X-Seating Existing - Seating Continuous 0.15 5
154 A_X-Sewer Existing - Sewer BORDER2 0.18 43
155 A_X-Stormwater Existing – Storm water Continuous 0.25 80
156 A_X-Walls Existing - Walls Continuous 0.13 9
157 A_X-Walls-Concrete Existing - Concrete Walls Continuous 0.13 9
158 A_X-Walls-Hatch Existing - Walls Hatch Continuous 0.05 151
159 A_X-WasteWater Existing - Waste Water Continuous 0.25 82
160 A_X-Windows Existing - Windows Continuous 0.13 9
161 Audio Visual AV_CCT Audio Visual - Video links DIVIDE 0.70 11
CAD Standards 29
162 AV_Equipment Audio Visual - Video equipment and fittings Continuous 0.20 6
163 AV_Text Audio Visual - Video equipment text Continuous 0.25 7
164
Building Management
Systems
BMS_Control Building Management System - Control devices and fittings Continuous 0.25 116
165 BMS_Equipment Building Management System - BMS equipment Continuous 0.25 210
166 BMS_Other Building Management System - Unspecified items Continuous 0.25 116
167 BMS_TempControl Building Management System - Temperature control Continuous 0.25 210
168 BMS_Text Building Management System - Notation on control devices Continuous 0.25 116
169
Data and
Communication
DC_CCTV Data and Communications - CCTV points Continuous 0.50 10
170 DC_CCTV_CCT Data and Communications - CCTV links DIVIDE 0.70 11
171 DC_Data_CCT Data and Communications - Data links DIVIDE 0.70 11
172 DC_DataJack Data and Communications - Data points Continuous 0.50 10
173 DC_DataPoint Data and Communications - Data VOIP phone and PC points etc... Continuous 0.50 10
174 DC_DataText Data and Communications - Data text Continuous 0.25 7
175 DC_InterC_CCT Data and Communications - Intercom and PA system links DIVIDE 0.70 11
176 DC_InterC_Text Data and Communications - Intercom and PA system text Continuous 0.25 7
177 DC_InterCommunication Data and Communications - Intercom and PA systems and equipment Continuous 0.50 10
178 DC_NetEquipment Data and Communications - Panels - ubs - routers and fittings Continuous 0.70 11
179 DC_Telkom_CCT Data and Communications - Telkom links DIVIDE 0.70 11
180 DC_TelkomJack Data and Communications - Telkom points Continuous 0.50 10
181 DC_TelomText Data and Communications - Telkom text Continuous 0.25 7
182 Electrical E_Appliances Electrical - Fridges - Microwaves etc Continuous 0.20 6
183 E_CableTray Electrical - Power cable trays Continuous 0.70 11
184 E_CableTrayText Electrical - Power cable tray text Continuous 0.25 7
185 E_ConsumerConn Electrical - Consumer connections ACAD_ISO10W100 0.70 11
186 E_ConsumerKiosk Electrical - Consumer distribution kiosk Continuous 0.50 10
187 E_ConsumerText Electrical - Consumer kiosk and connections text Continuous 0.25 7
188 E_Distribution Board Electrical - Distribution boards Continuous 0.50 10
189 E_Distribution Board_Text Electrical - Distribution boards text Continuous 0.25 7
190 E_Duct Electrical - Electrical ducting ACAD_ISO03W100 0.70 11
191 E_Fan Electrical - Ceiling and sweeping fan Continuous 0.13 41
192 E_Light Electrical - Electrical light switches and fittings Continuous 0.50 10
193 E_LightText Electrical - Electrical lighting text Continuous 0.25 7
194 E_LightTrunking Electrical - Electrical lighting trunking ACAD_ISO05W100 0.70 11
195 E_MiniSub Electrical - Mini sub-stations Continuous 0.50 10
196 E_MiniSubText Electrical - Mini sub-stations text Continuous 0.25 7
197 E_Power Electrical - Power points Continuous 0.50 10
198 E_PowerDims Electrical - Power dimensions Continuous 0.05 8
199 E_PowerSkirting Electrical - Power skirting ACAD_ISO05W100 0.70 11
200 E_PowerSkirtingText Electrical - Power skirting text Continuous 0.25 7
201 E_PowerText Electrical - Electrical text Continuous 0.25 7
202 E_PowerTrunkText Electrical - Power trunking text Continuous 0.25 7
203 E_PowertTrunk Electrical - Power trunking ACAD_ISO03W100 0.70 11
204 E_ReticulationSleeve Electrical - Reticulation sleeve ACAD_ISO10W100 0.70 11
CAD Standards 30
205 E_ReticulationSleeveText Electrical - Reticulation sleeve text Continuous 0.25 7
206 E_Sleeves Electrical - Sleeves ACAD_ISO10W100 0.70 11
207 E_SleeveText Electrical - Sleeve text and labels Continuous 0.25 7
208 E_StreetLight Electrical - Street light poles Continuous 0.50 10
209 E_StreetLightCable Electrical - Street Lighting cables PHANTOM 0.70 11
210 E_StreetLightText Electrical - Street light text Continuous 0.25 7
211 E-LightDims Electrical - Electrical light dimensions Continuous 0.05 8
212 E-LightReticulation Electrical - Lights and reticulation cables ACAD_ISO10W100 0.70 11
213 Essential Services
ES_EmergencyLight Essential Services - Emergency and exit sign lighting - cables etc... Continuous 0.25 20
214 ES_Evacuation Essential Services - Evacuation systems - speakers - etc... Continuous 0.25 20
215 ES_ExitDoor Essential Services - Door for emergency routes Continuous 0.25 20
216 ES_Extinguisher Essential Services - Fire extinguisher Continuous 0.25 20
217 ES_Fire_CCT Essential Services - Links DIVIDE 0.25 20
218 ES_FireDetectors Essential Services - Detectors Smoke and rate of rise Continuous 0.25 20
219 ES_FireDoor Essential Services - Fire door Continuous 0.25 20
220 ES_FirePanel Essential Services - Fire control indicator panel Continuous 0.25 20
221 ES_FireText Essential Services - Fire text Continuous 0.25 7
222 ES_HazardChemicals Essential Services - Hazardous chemicals and elements Continuous 0.25 20
223 ES_Hydrant Essential Services - Hydrant and hose reels Continuous 0.25 20
224 ES_Routes Essential Services - Emergency exit routes Continuous 0.25 100
225 ES_SmokeDoor Essential Services - Smoke doors Continuous 0.25 20
226 ES_Sprinkler Essential Services - Sprinkler systems and fittings Continuous 0.25 20
227 Facilities Management
FM_Audit Facilities Management - Space being audited Continuous 0.25 7
228 FM_CirculationSpace Facilities Management - Circulation space - polygon Continuous 0.25 54
229 FM_CR_PL$TXT Facilities Management - For Archibus only Continuous 0.05 4
230 FM_CRPL$ Facilities Management - For Archibus only Continuous 0.05 4
231 FM_DeptUsage Facilities Management - Area used by department Continuous 0.25 7
232 FM_DeptUsageText Facilities Management - Text associated with area for department Continuous 0.25 7
233 FM_FL_PL$ Facilities Management - For Archibus only Continuous 0.10 1
234 FM_FloorAreaPolyline Facilities Management - Floor area polyline Continuous 0.10 1
235 FM_FLPS$TXT Facilities Management - For Archibus only Continuous 0.10 1
236 FM_Footprint Facilities Management - Building foot print continuous Continuous 0.10 1
237 FM_OfficeArea Facilities Management - Highlight office areas Continuous 0.15 50
238 FM_OfficeOccupancy Facilities Management - Names and details of occupants Continuous 0.15 3
239 FM_RM_PL$ Facilities Management - For Archibus only Continuous 0.05 5
240 FM_RM_PL$TXT Facilities Management - For Archibus only Continuous 0.05 5
241 FM_RoomNumber Facilities Management - Room numbers Continuous 0.25 162
242 FM_RoomType Facilities Management - Room type Continuous 0.25 162
243 FM_SignableSpace Facilities Management - Rooms - polygon Continuous 0.25 162
244 General G_10mmText General - 10mm High text Continuous 0.25 221
245 G_14mmText General - 14mm High text Continuous 0.25 161
246 G_2.0mmText General - 2.0mm High text Continuous 0.13 31
247 G_2.5mmText General - 2.5mm High text Continuous 0.13 41
CAD Standards 31
248 G_3.5mmText General - 3.5mm High text Continuous 0.25 53
249 G_5.0mmText General - 5.0mm High text Continuous 0.25 33
250 G_7.0mmText General - 7.0mm High text Continuous 0.25 141
251 G_Background General - Shadow background for use by consultants Continuous 0.13 9
252 G_BuildNumber General - Building code number Continuous 0.25 7
253 G_Details-2.0mmText General - 2.0mm Text for Details in different Scale Continuous 0.13 51
254 G_Details-Dimension General - Dimensions for Details in different Scale Continuous 0.05 8
255 G_Dimensions General - Drawing dimensions Continuous 0.05 8
256 G_Hatch General - Drawing hatching Continuous 0.10 1
257 G_Logo General - Drawing logo Continuous 0.25 7
258 G_Margins General - Drawing margins Continuous 0.25 255
259 G_Mview General - Drawing view ports Continuous 0.25 7
260 G_ScaleBar General - Scale bar Continuous 0.25 7
261 G_SightLines General - Sight lines for projection viewing Continuous 0.05 8
262 G_TextGeneral General - General text Continuous 0.25 7
263 G_TextPerm General - Drawing permanent text Continuous 0.25 7
264 G_TextPointers General - Text arrows and pointers Continuous 0.05 8
265 G_TextSpecialNotes General - Special non title text and notes Continuous 0.10 1
266 G_TextTitle General - General text Continuous 0.25 191
267 G_TitleBlock General - Drawing title block Continuous 0.25 191
268 G_TitleBlockLight General - Titlebloc light Continuous 0.05 8
269 G_ViewPort General - Drawing Viewport Continuous 0.05 8
270 G_ViewportNoPlot General - Drawing Viewport No Plot Continuous 0.25 40
271 Hydraulic H_ColdWaterServices Hydraulic - Piping for cold water in building ACAD_ISO10W100 0.25 130
272 H_ColdWaterText Hydraulic - Cold water text Continuous 0.25 7
273 H_Equipment Hydraulic - General hydraulic equipment Continuous 0.25 7
274 H_FireEquip Hydraulic - Hydrant - sprinklers etc... Continuous 0.25 20
275 H_FireHatch Hydraulic - Hatching for fire services Continuous 0.70 11
276 H_FireHoseReels Hydraulic - Piping and components for fire hose reels Continuous 0.20 13
277 H_FireHoseText Hydraulic - Text for piping and components for fire hose reels Continuous 0.25 7
278 H_FireHydrantPipe Hydraulic - Piping and components for fire hydrants Continuous 0.70 11
279 H_FireHydrantText Hydraulic - Text for fire hydrants Continuous 0.25 7
280 H_FireServices Hydraulic - Piping for fire mains in building Continuous 0.25 20
281 H_FireText Hydraulic - Fire services text Continuous 0.25 7
282 H_FlushWater Hydraulic - Piping for flush water systems in building ACAD_ISO03W100 0.25 210
283 H_GreaseTraps Hydraulic - Grease traps and pts ACAD_ISO02W100 0.25 90
284 H_HotwaterCylReliefPiping Hydraulic - Piping for hot water cylinder relief piping ACAD_ISO10W100 0.25 240
285 H_HotwaterReturn Hydraulic - Piping for hot water return ACAD_ISO10W100 0.25 240
286 H_HotwaterSupply Hydraulic - Piping for hot water supply in building ACAD_ISO10W100 0.25 240
287 H_HotwaterText Hydraulic - Hot water text Continuous 0.25 7
288 H_SanitaryText Hydraulic - Text for sanitary and waste descriptions Continuous 0.25 90
289 H_SewerServices Hydraulic - Piping sewer services in building Continuous 0.25 90
290 H_SprinklerPipe Hydraulic - Piping and components for sprinklers Continuous 0.18 12
CAD Standards 32
291 H_SprinklerServices Hydraulic - Fire sprinkler services CENTER 0.25 20
292 H_SprinklerText Hydraulic - Text for piping and components for sprinklers Continuous 0.25 7
293 H_StormWater Hydraulic - Piping for storm water in building ACAD_ISO02W100 0.13 41
294 H_StormwaterText Hydraulic - Storm water text Continuous 0.25 7
295 H_TepidServices Hydraulic - Tepid water services HIDDEN 0.25 20
296 H_TextGeneral Hydraulic - General descriptive text Continuous 0.25 7
297 H_Vent Hydraulic - Vents to sewer and waste piping in building HIDDEN 0.25 90
298 H_WasteWater Hydraulic - Piping for waste and drains in building HIDDEN 0.13 41
299 Mechanical ME_Air Mechanical and Lifts - Air lines Continuous 0.25 130
300 ME_AirConditioningUnits Mechanical and Lifts - Air conditioning unit Continuous 0.20 6
301 ME_AirText Mechanical and Lifts - Air lines text Continuous 0.25 130
302 ME_ChilledWaterPipe Mechanical and Lifts - Piping for chilled water DIVIDE 0.25 30
303 ME_CompAirEquip Mechanical and Lifts - Compressed air equipment Continuous 0.25 142
304 ME_CompAirPipe Mechanical and Lifts - Compressed air piping ACAD_ISO05W100 0.25 142
305 ME_CompAirText Mechanical and Lifts - Compressed air text Continuous 0.25 142
306 ME_Condensate Mechanical and Lifts - Condensate ACAD_ISO03W100 0.25 25
307 ME_CondenserWaterPiping Mechanical and Lifts - Piping for condenser ACAD_ISO03W100 0.25 100
308 ME_DuctingExhaust Mechanical and Lifts - Exhaust ducting work Continuous 0.25 20
309 ME_DuctingExhaustText Mechanical and Lifts - Ducting exhaust text Continuous 0.25 20
310 ME_DuctingExisting Mechanical and Lifts - Existing ducting ACAD_ISO03W100 0.13 9
311 ME_DuctingReturn Mechanical and Lifts - Return air ducting ACAD_ISO06W100 0.25 100
312 ME_DuctingReturnText Mechanical and Lifts - Return air ducting text Continuous 0.25 100
313 ME_DuctingSupply Mechanical and Lifts - Supply ducting work Continuous 0.25 160
314 ME_DuctingSupplyText Mechanical and Lifts - Supply ducting work text Continuous 0.25 160
315 ME_Equipment Mechanical and Lifts - Mechanical equipment - solid lines Continuous 0.20 6
316 ME_EquipmentExhaust Mechanical and Lifts - Exhaust air equipment Continuous 0.25 20
317 ME_EquipmentExisting Mechanical and Lifts - Existing mechanical equipment ACAD_ISO02W100 0.13 9
318 ME_EquipmentSupply Mechanical and Lifts - Supply air equipment Continuous 0.25 160
319 ME_FlexibleDuctingExhaust Mechanical and Lifts - Exhaust flexible ducting - solid lines Continuous 0.25 240
320 ME_FlexibleDuctingSupply Mechanical and Lifts - Supply flexible ducting - solid lines Continuous 0.25 170
321 ME_GasEquip Mechanical and Lifts - Gas Equipment-Manifolds etc…. Continuous 0.25 60
322 ME_GasPiping Mechanical and Lifts - Gas piping BORDER 0.25 60
323 ME_GasText Mechanical and Lifts - Gas text Continuous 0.25 60
324 ME_HeatingEquip Mechanical and Lifts - Heating text Continuous 0.25 32
325 ME_HeatingPipe Mechanical and Lifts - Piping for heating PHANTOMX2 0.25 32
326 ME_HiddenDucting_EquipText Mechanical and Lifts - Hidden ducting and equipment text HIDDEN 0.25 224
327 ME_HiddenDuctingExhaust Mechanical and Lifts - Exhaust ducting work - hidden lines HIDDEN 0.25 224
328 ME_HiddenDuctingReturn Mechanical and Lifts - Return air ducting - hidden lines HIDDEN 0.25 224
329 ME_HiddenDuctingSupply Mechanical and Lifts - Supply ducting hidden HIDDEN 0.25 224
330 ME_HiddenEquipment Mechanical and Lifts - Mechanical equipment - hidden lines HIDDEN 0.25 224
331 ME_Lift Mechanical and Lifts - Lift cages outlines Continuous 0.50 8
332 ME_PipeEquipment Mechanical and Lifts - General piping for equipment Continuous 0.13 41
333 ME_PipingText Mechanical and Lifts - Piping text Continuous 0.13 41
CAD Standards 33
334 ME_TextDims Mechanical and Lifts - General text and dimensions Continuous 0.50 8
335 ME_VacuumEquip Mechanical and Lifts - Vacuum equipment Continuous 0.25 145
336 ME_VacuumPipe Mechanical and Lifts - Vacuum piping ACAD_ISO06W100 0.25 145
337 ME_VacuumText Mechanical and Lifts - Vacuum text Continuous 0.25 145
338 Structural S_Architect Structural - Items from Architect Continuous 0.25 8
339 S_BWK Structural - Load bearing BWK: Plan/Elevation/Section Continuous 0.25 140
340 S_BWK Alterations Structural - Load bearing BWK: Alterations HIDDEN2 0.25 9
341 S_BWK Under Structural - Load bearing BWK: Hidden detail (Support under) HIDDEN2 0.25 150
342 S_Cast-In Items Structural - Items to be cast into concrete Continuous 0.25 8
343 S_Centre Structural - Centre line CENTER2 0.25 2
344 S_Civil Structural - Items from Civil Engineer Continuous 0.25 2
345 S_Cloud-Hold Structural - Cloud for areas on hold Continuous 0.25 3
346 S_Cloud-Rev Structural - Cloud for areas revised PHANTOM2 0.25 8
347 S_Col Structural - Concrete column: Section through vertical element on plan Continuous 0.25 3
348 S_Col Numbers Structural - Concrete column: Numbers Continuous 0.25 3
349 S_Col Text Structural - Concrete column: Annotations Continuous 0.25 2
350 S_Col Under Structural - Concrete column: Hidden detail (Support under) HIDDEN2 0.25 2
351 S_Concrete Elevation Structural - Concrete elements in elevation Continuous 0.25 1
352 S_Concrete Section Structural - Concrete elements in section Continuous 0.25 3
353 S_Construct Line Structural - Non plot - Construction lines for drafting Continuous 0.25 7
354 S_Demolish Structural - Items to be demolished HIDDEN2 0.25 8
355 S_Existing Structural - Existing items: Plan/Elevation/Section PHANTOM2 0.25 9
356 S_Finishes Structural - Finishes to structural elements Continuous 0.25 8
357 S_Foundation Structural - Foundations: Plan/Elevation Continuous 0.25 1
358 S_Foundation Text Structural - Foundations: Annotations Continuous 0.25 2
359 S_Foundation Under Structural - Foundations: Hidden detail HIDDEN2 0.25 2
360 S_Future Structural - Items for future expansion PHANTOM2 0.25 9
361 S_Grout Structural - Structural grouting Continuous 0.25 9
362 S_Hatch Structural - Hatch in section Continuous 0.25 9
363 S_Hatch Under Structural - Hatch for hidden elements (Support under) HIDDEN2 0.25 9
364 S_Joints IJ Structural - Structural isolation joints DIVIDE2 0.25 3
365 S_Joints SC Structural - Structural saw-cut joints PHANTOM2 0.25 6
366 S_Keyplan Structural - Structural key plan Continuous 0.25 6
367 S_Level Line Structural - Line indicating floor level DASHDOT2 0.25 8
368 S_Mesh Structural - Mesh reinforcing HIDDEN2 0.25 1
369 S_Pile Structural - Piles: Elevation/Section Continuous 0.25 6
370 S_Pile Number Structural - Piles: Numbers Continuous 0.25 3
371 S_Pile Text Structural - Piles: Annotations Continuous 0.25 2
372 S_Pile Under Structural - Piles: Hidden (Support under) HIDDEN2 0.25 2
373 S_Rebar Structural - Rebar detail on concrete drawing: Plan/Elevation Continuous 0.25 3
374 S_Rebar Section Structural - Rebar detail on concrete drawing: Section Continuous 0.25 1
375 S_Rock Structural - Ground conditions: Rock PHANTOM2 0.25 9
376 S_RWP Structural - Rain water downpipes: Plan Continuous 0.25 6
CAD Standards 34
377 S_RWP Text Structural - Rain water downpipes: Annotations Continuous 0.25 2
378 S_Slab Structural - Concrete slab: Plan/Elevation (Immediate foreground) Continuous 0.25 1
379 S_Slab Beyond Structural - Concrete slab: Plan/Elevation (Further away from view) Continuous 0.25 2
380 S_Slab Falls Structural - Concrete slab: Cast to falls kink line Continuous 0.25 9
381 S_Slab Section Structural - Concrete slab: Section Continuous 0.25 3
382 S_Slab Text Structural - Concrete slab: Annotations Continuous 0.25 2
383 S_Slab Under Structural - Concrete slab: Hidden detail HIDDEN2 0.25 2
384 S_Sleeves Structural - Sleeves through concrete elements Continuous 0.25 6
385 S_Soil Structural - Ground conditions: Soil PHANTOM2 0.25 9
386 S_Steel Structural - Structural steel items: Plan/Elevation/Section Continuous 0.25 40
387 S_Steel Under Structural - Structural steel items: Hidden detail (Support under) HIDDEN2 0.25 9
388 S_Surface Bed Structural - Concrete surface bed in section Continuous 0.25 3
389 S_Symbols Structural - Structural symbols Continuous 0.25 1
390
S_Text Structural - Structural Annotations Continuous 0.25 2
391 S_Timber Structural - Structural timber details Continuous 0.25 33
392 S_Wall Structural - Concrete wall: Section through vertical element on plan Continuous 0.25 3
393 S_Wall Section Structural - Concrete wall: Section Continuous 0.25 3
394 S_Wall Text Structural - Concrete wall: Annotation Continuous 0.25 2
395 S_Wall Under Structural - Concrete wall: Hidden detail (Support under) HIDDEN2 0.25 2
396 Security SEC_CCT Security - Security device links DIVIDE 0.70 11
397 SEC_Device Security - Security device Continuous 0.50 10
398 SEC_Text Security - Security device text Continuous 0.25 7
399 Survey and
Landscaping
SU_BikeRack Survey & Landscaping - Bike rack Continuous 0.20 6
400 SU_Bollard Survey & Landscaping - Bollards Continuous 0.10 1
401 SU_BollardMech Survey & Landscaping - Mechanical bollard Continuous 0.10 1
402 SU_Boomgate Survey & Landscaping - Boom gate Continuous 0.25 7
403 SU_Bridge Survey & Landscaping - Bridge Continuous 0.13 41
404 SU_BuildingText Survey & Landscaping - Text for describing buildings Continuous 0.35 2
405 SU_CoolTowers Survey & Landscaping - Cooling towers Continuous 0.10 1
406 SU_EdgeFormation Survey & Landscaping - Edge of formation Continuous 0.25 7
407 SU_EdgeRoad Survey & Landscaping - Edge of road / path bitumen Continuous 0.13 41
408 SU_EmbankmentBottom Survey & Landscaping - Bottom of embankment Continuous 0.10 1
409 SU_EmbankmentTop Survey & Landscaping - Top of embankment Continuous 0.10 1
410 SU_Fence Survey & Landscaping - Fences Continuous 0.05 5
411 SU_GardenBed Survey & Landscaping - Garden bed Continuous 0.15 3
412 SU_Gate Survey & Landscaping - Gate Continuous 0.25 7
413 SU_InvertLevel Survey & Landscaping - Invert levels Continuous 0.25 7
414 SU_KerbBack Survey & Landscaping - Back of kerb or channel Continuous 0.10 1
415 SU_KerbFace Survey & Landscaping - Face / top of kerb or channel Continuous 0.10 1
416 SU_KerbLip Survey & Landscaping - Lip of kerb or channel Continuous 0.13 41
417 SU_Kerblnvert Survey & Landscaping - Invert of kerb or channel Continuous 0.25 7
418 SU_Kiosk Survey & Landscaping - Kiosk Continuous 0.13 41
419 SU_LandChannel Survey & Landscaping – Land channel boundaries Continuous 0.05 5
CAD Standards 35
420 SU_LightPole Survey & Landscaping - Light poles Continuous 0.13 41
421 SU_MajorContour Survey & Landscaping - Major contour Continuous 0.25 80
422 SU_MappingGrid Survey & Landscaping - Mapping grid Continuous 0.25 253
423 SU_MinorContour Survey & Landscaping - Minor contour Continuous 0.25 40
424 SU_Monument Survey & Landscaping - Monument Continuous 0.10 1
425 SU_OpenDrain Survey & Landscaping - Open or spoon drain Continuous 0.25 7
426 SU_Paving Survey & Landscaping - Paving Continuous 0.20 13
427 SU_PedestPath Survey & Landscaping - Pedestrian path Continuous 0.20 13
428 SU_Pole Survey & Landscaping - Power & other poles Continuous 0.13 41
429 SU_Pond Survey & Landscaping - Pond Continuous 0.25 130
430 SU_PSM Survey & Landscaping - Pavement survey mark Continuous 0.13 41
431 SU_Ramp Survey & Landscaping - Pedestrian ramps Continuous 0.20 6
432 SU_RetainingWall Survey & Landscaping - Retaining wall Continuous 0.20 6
433 SU_RL Survey & Landscaping - Spot level Continuous 0.25 7
434 SU_RoadsCL Survey & Landscaping - Road centre line Continuous 0.25 251
435 SU_RubbishBin Survey & Landscaping - Rubbish bins Continuous 0.10 1
436 SU_Seat Survey & Landscaping - Benches and Seats Continuous 0.10 1
437 SU_Shrubs Survey & Landscaping - Shrubs and garden plants Continuous 0.15 3
438 SU_Sign Survey & Landscaping - Sign Continuous 0.10 1
439 SU_SpeedHump Survey & Landscaping - Speed humps Continuous 0.20 6
440 SU_Steps Survey & Landscaping - External steps and stairs Continuous 0.20 6
441 SU_SubStructure Survey & Landscaping - Underground Structures DASHED2 0.25 30
442 SU_SurveyLand Survey & Landscaping - Survey and landscaping text Continuous 0.25 7
443 SU_TitleBoundary Survey & Landscaping - Title boundary of property Continuous 0.13 41
444 SU_Trees Survey & Landscaping - Trees Continuous 0.15 3
445 SU_TSM Survey & Landscaping - Temporary survey mark Continuous 0.13 41
446 SU_USMap Survey & Landscaping - University map Continuous 0.25 7
447 SU_WaterFeature Survey & Landscaping - Natural water areas - dams - etc.... Continuous 0.25 130
448 Underground Services
US_BoreHole Underground Services - Bore holes Continuous 0.25 20
449 US_ChilledWater Underground Services - Chilled water piping Continuous 0.25 40
450 US_ChlorinePit Underground Services - Chlorine pit Continuous 0.25 90
451 US_CondenserWater Underground Services - Condenser water pipes Continuous 0.25 44
452 US_ConstructDim Underground Services - Dimensions for underground services Continuous 0.05 8
453 US_ConstructFooting Underground Services - Foundations Continuous 0.25 30
454 US_ConstructText Underground Services - Foundation text Continuous 0.25 7
455 US_Data Underground Services - Data Continuous 0.25 20
456 US_ElectricalConduit Underground Services - Electrical conduit Continuous 0.25 200
457 US_ElectricalHV_Text Underground Services - Electrical HV cable text Continuous 0.25 7
458 US_ElectricalLV Underground Services - Electrical LV cable and feeders Continuous 0.25 20
459 US_ElectricalLV_Text Underground Services - Electrical LV cable text Continuous 0.25 20
460 US_ElectricalPit Underground Services - Electrical pit Continuous 0.25 20
461 US_ElectricalStreetLight Underground Services - Street lighting Continuous 0.25 142
462 US_ElectricalSubstation Underground Services - Sub station Continuous 0.25 20
CAD Standards 36
463 US_ElectricalSubstation-Hatch Underground Services - Hatching Continuous 0.25 20
464 US_ElectricalText Underground Services - Electrical text Continuous 0.25 20
465 US_ElectricaltHV Underground Services - Electrical HV Continuous 0.25 170
466 US_Fibre Underground Services - Fibre optics Continuous 0.25 140
467 US_FibreConduit Underground Services - Fibre optic conduit Continuous 0.25 200
468 US_FibreText Underground Services - Fibre optic text Continuous 0.25 140
469 US_FireHydrant Underground Services - Fire hydrants Continuous 0.25 20
470 US_FireHydrant_ID Underground Services - Fire Hydrant ID Continuous 0.25 20
471 US_FireService Underground Services - Fire service Continuous 0.25 20
472 US_FireText Underground Services - Fire Text Continuous 0.25 20
473 US_GasDimension Underground Services - Gas dimensions Continuous 0.05 8
474 US_GasHigh Pressure Underground Services - Gas high pressure Continuous 0.25 30
475 US_GasLow Pressure Underground Services - Gas low pressure Continuous 0.25 220
476 US_GasMeter Underground Services - Gas meters Continuous 0.25 60
477 US_GasMeter_ID Underground Services - Gas meters ID Continuous 0.25 60
478 US_GasPipe_ID Underground Services - Gas pipe ID Continuous 0.25 60
479 US_GasRegulator Underground Services - Gas regulator Continuous 0.25 133
480 US_GasRegulator_ID Underground Services - Gas regulator ID Continuous 0.25 133
481 US_GasText Underground Services - Gas service text Continuous 0.25 133
482 US_GasValve Underground Services - Gas valves Continuous 0.25 60
483 US_GasValve_ID Underground Services - Gas valves ID Continuous 0.25 60
484 US_HeatPumpServices Underground Services - Heat pump water Continuous 0.25 82
485 US_HotWater Underground Services - Hot water piping Continuous 0.25 82
486 US_HotwWaterText Underground Services - Hot water service text Continuous 0.25 82
487 US_Irrigation Underground Services - Irrigation system Continuous 0.25 90
488 US_PitElectrical_ID Underground Services - Electrical pit ID Continuous 0.25 20
489 US_PitFibre Underground Services - Fibre pit Continuous 0.25 140
490 US_PitFibreOptic_ID Underground Services - Fibre optic pit ID Continuous 0.25 140
491 US_PitGas Underground Services - Gas pit Continuous 0.25 60
492 US_PitGas_ID Underground Services - Gas pit ID Continuous 0.25 60
493 US_PitHotWater Underground Services - Hot water pit Continuous 0.25 82
494 US_PitHotWater_ID Underground Services - Hot water pit ID Continuous 0.25 82
495 US_PitSewer Underground Services - Sewer pit Continuous 0.25 90
496 US_PitSewer_ID Underground Services - Sewer pit ID Continuous 0.25 90
497 US_PitSteam Underground Services - Steam pit Continuous 0.25 20
498 US_PitSteam_ID Underground Services - Steam pit ID Continuous 0.25 22
499 US_PitStormWater Underground Services - Storm water pit Continuous 0.25 22
500 US_PitStormWater_ID Underground Services - Storm water pit ID Continuous 0.25 22
501 US_PitTelkom Underground Services - Telkom pit Continuous 0.25 20
502 US_PitTelkom_ID Underground Services - Telkom pit ID Continuous 0.25 20
503 US_PitWater Underground Services - Water pit Continuous 0.25 130
504 US_PitWater_ID Underground Services - Water pit ID Continuous 0.25 130
505 US_SewerNeutralisers Underground Services - Grease traps Continuous 0.25 20
CAD Standards 37
7 APPENDIX B
7.1 Underground Services Unique Information
This appendix documents the underground service that is required, by the University of
Stellenbosch to be surveyed. It also specifies the types of information required for each
underground service. A pro forma spreadsheet is available from the Space and Data
Management Office, University of Stellenbosch
506 US_SewerPipe Underground Services - Sewer pipe Continuous 0.25 90
507 US_SewerText Underground Services - Sewer text Continuous 0.25 90
508 US_SteamPipe Underground Services - Steam pipe Continuous 0.25 20
509 US_SteamText Underground Services - Steam text Continuous 0.25 20
510 US_StormPipe Underground Services - Storm water pipe Continuous 0.25 22
511 US_StormText Underground Services - Storm water text Continuous 0.25 22
512 US_TanksDiesel Underground Services - Diesel tanks Continuous 0.25 20
513 US_TanksOld Underground Services - Old tanks Continuous 0.25 30
514 US_TanksPetrol Underground Services - Petrol tanks Continuous 0.25 20
515 US_TelkomConduit Underground Services - Telkom conduit Continuous 0.25 200
516 US_TelkomLine Underground Services - Telkom cable Continuous 0.25 200
517 US_TelkomText Underground Services - Telkom text Continuous 0.25 200
518 US_Unknown Underground Services - Unknown service Continuous 0.25 20
519 US_WaterDimensions Underground Services - Dimensions Continuous 0.05 8
520 US_WaterMain Underground Services - Water main Continuous 0.25 130
521 US_WaterMain_ID Underground Services - Water main ID Continuous 0.25 130
522 US_WaterMeter_ID Underground Services - Water meter ID Continuous 0.25 170
523 US_WaterText Underground Services - Water text Continuous 0.25 130
524 US_WaterValve Underground Services - Water valve Continuous 0.25 130
525 US_WaterValve_ID Underground Services - Water valve ID Continuous 0.25 130
CAD Standards 38
8 APPENDIX C
8.1 Underground Services Unique Entity Codes
All underground entities surveyed will surveyed will be supplied with a unique entity
code. The code will be tabled in ad Excel spreadsheet with the information as requested
in Appendix C. The unique entity code shall also be noted on the drawing next to the
entity concerned and be bounded by a polyline.
The format of this code is made up of two sub parts. The first sub part is a prefix
representing the underground service of the entity. A list of these prefixes is
documented below. The second sub part is a unique five digit number that will be
supplied to entity sequentially.
CODE PREFIX DESCRIPTION
CSS CENTRAL SUPERVISORY / MANAGEMENT SYSTEM
CTD COOLING TOWER DISCHARGE
DAT CAMPUS DATA RETICULATION
EGC EMERGENCY GENERATOR CONNECTION
GAS GAS MAINS
HVE HIGH VOLTAGE ELECTRICITY
HWS HOT WATER AND HEAT PUMP RETICULATION
LVE LOW VOLTAGE ELECTRICITY
MWS MAINS WATER
SEW SEWERS
STL STREET LIGHTING
STW STORM WATER
TEL TELKOM
UGE GENERAL ELECTRICAL
CAD Standards 39
8.2 Example – Underground Storm Water CAD File
The Following is an example of table information supplied with a drawing.
A CAD file for underground storm water:
The associated Excel spreadsheet:
STORM WATER
Pipes
Entity Code Material Date Dia Depth
STW 1265 RC 1965 300 1.45
STW 1267 RC 1965 300 1.5
STW 1268 RC 1965 300 1.35
STW 1269 RC 1980 300 1.3
STW 1270 RC 1980 300 1.3
STW 1271 RC 1980 300 1.35
STW 1272 UPVC 2001 110 1.45
STW 1273 UPVC 2002 110 1.05
STW 1274 RC 1985 150 0.9
Pits
Entity Code Date Cover type Condition RL Top Depth
STW-P 1266 1965 Cast Iron Good 4.55 1.7
STW-P 1268 1980 Concrete Poor 4.56 1.5
STW-P 1270 1980 Cast Iron Fair 4.68 1.35
STW-P 1274 1980 Cast Iron Fair 4.60 1.45
