CANCER INSTITUTE (WIA)
Canal Bank Road, Adyar
Chennai 600 020 Phone:+91 44 2220 9150 Extn (179)
Email:[email protected]
www.caninstitutewia.in
Addendum to Tender – I
PROCUREMENT OF MEDICAL EQUIPMENTS
Procurement of : Linear Accelerator
BID REFERENCE: CI: SCI:NP/ROG/P-I/2016-17/01DATED DECEMBER 15, 2016
Abstract Schedule
SL.
No. Description Amount in Rs:
1. HVAC WORKS
2. CIVIL AND INTERIOR WORKS
3 ELECTRICAL WORKS
Grand Total Rs
Sr.
No. Item Description Qty. Unit Unit Rate
in Rs.
Total Amt
in Rs.
HVAC WORKS
1
Supply installation testing commissioning of 8.5 ton ductble split unit with supply
of grills,ducting, insulation with 4 fresh air arrangement, upto 5 mrt copper pipe
considered.(N+N) with 100% standy-by
Ls No
2 Supply of 2 ton Hi wall split unit for TPS room with 5 kva stabilizer, upto 5 mrt
copper pipe considered with 100% standy-by Ls No
3 Supply of 2 ton Hi wall split unit for UPS room with 5 kva stabilizer, upto 5 mrt
copper pipe considered with 100% standy-by Ls
4 Supply of Ceiling suspended unit for control consol area2 tr, upto 5 mtr copper
pipe considered. Ls no
5 Supply installation of Hooks for lifting ,shifting, and instalation of Linac
machine.
One No
TOTAL
Sr.
No. Item Description Qty. Unit
Unit Rate in
Rs.
Total Amt in
Rs.
CIVIL AND INTERIOR WORKS
1
Excavation in all types of soil including dense soil, disintegrated/ weathered/ soft rock
(Poclainable) for Footings of columns, Retaining walls, Core walls, catch pits, Pits,
Trenches, etc., by mechanical means including manual excavation for leveling, dressing
the edges, with all leads and lifts including back filling in layers of 150mm with watering
and compaction. dewatering of both ground and surface water, removal of slurry
generated while excavation and keeping the area free of water with necessary shoring,
struting, required for keeping earth in position etc, Rate to include disposing the excess
earth and spreading in layers to the required levels within the site wherever specified by
the local authorities. Note: Working space and Provision of slopes if required for
execution shall not be paid seperately. Rate to include all royalties, Seignorage, taking
statutory approvals as necessary to carry out the works etc., complete.
Upto 1.50 Metre depth below average ground level.
Cum
Supply and filling in foundations and the area whereever specified with approved good
quality filling materials in plinths, area development etc. wherever specified in layers of
not exceeding 150 mm thick including breaking clods,storing,transportation ,double
handling, watering, compacting each layer with vibratory compactor and at unaccessible
places with wooden/steel rammers to achieve 90 to 95% proctor density at optimum
moisture content, all leads and lifts, bailing/ pumping out of water to keep site dry while
backfilling; cost shall include conveyance of all materials, labour, machinery etc.
complete as directed.The rate to includes loading,unloading, hire and fuel charges for
tools and plants, all royalties,taking staxtutory approvals as necessary to carry out the
works and other incidental charges etc., complete. (Soil excavated from within site can
be used)
Cum
1
Providing and casting in situ cement concrete M-25 (Concrete Density 2.35 gms/cc) of
trap / granite /quartzite/ gneiss metal for R.C.C. Walls as per detailed designs and
drawings or as directed including centering, formwork, cover blocks compacting and
roughening if special finish is to be provided and curing complete. (Excluding
reinforcement).With fully automatic micro processor based PLC with SCADA enabled
reversible drum type concrete mixer. With natural sand.
i Between Maze and Console with Bed thickness 800mm Cum
ii Between Maze and Waiting hall with Bed thickness 600mm Cum
Sr.
No. Item Description Qty. Unit
Unit Rate in
Rs.
Total Amt in
Rs.
iii At Machine opposite inside Side Wall with Bed thickness 500mm Cum
iv Between Blood sample Room and Machine with Bed thickness 450mm Cum
v At Console with Bed thickness 300mm Cum
vi Near PET CT with Bed thickness 230mm Cum
vii Between Console and Maze with Bed thickness 200mm
Cum
viii At roof top with Bed thickness 900mm Cum
2
Providing and injecting chemical emulsion for PRE-CONSTRUCTIONAL anti-termite
treatment and creating a chemical barrier under and around the column pits, wall
trenches, basement excavation, top surface of plinth filling, junction of wall and floor,
along the external perimeter of building expansion joints, surroundings of pipes &
conduits etc. complete (plinth area of the building at ground floor only shall be
measured). (Chloropyrophos 20%)
Sqm
9 Supply of MS plate 70mm thick , 7.89g/CC (5602MM X 2794MM) AND (2705mm X
3500mm) KG
10 Supply of MS plate 265 mm thick , 7.89g/CC (3020X 4668MM) and (368mmx 113mm)
KG
11 Supply of MS plate 113mm thick , 7.89g/CC , (368mm x 4668mm)
KG
12 150mm thick Brick work in work with bricks of class designation 75 in super structure
above plinth for all heights in cement mortar 1:4 ( 1 cement : 4 coarse sand ) Sqm
13 230mm thick Brick work in work with bricks of class designation 75 in super structure
above plinth for all heights in cement mortar 1:4 ( 1 cement : 4 coarse sand ) Sqm
14
Dismantling of Plain Cement Concrete or Flooring or Brick work to any depth and
width, at all levels below & above Ground Level of any shape, removal of debris,
disposing the same away from the site, loading and unloading, making the surface good
etc. complete. Rate shall include for dismantling of Plain Cement Concrete / Brick work
by manually / mechanical means with necessary tools and plants, scaffolding, water and
power charges, cleaning the surface, preparation of surface etc. Rate shall include for
stacking the serviceable materials and disposing the unserviceable materials/debris away
from the site premises by mechanical means including loading, unloading, clearing the
site etc. complete, as directed.
Cum
Sr.
No. Item Description Qty. Unit
Unit Rate in
Rs.
Total Amt in
Rs.
Providing and applying 12mm thick plaster in cement mortar mix ratio CM 1:6 (1
cement : 6 sand) mixed with polypropylene fibers as per instruction of the approved
manufacturer, to internal surfaces of concrete and masonry work; including raking out
joints, hacking concrete surfaces and applying approved chemical bonding agent and
applying a scratch coat over concrete surfaces by bonding / adhesive chemical coat as
directed by approved manufacturer to create a key, cleaning / grooving deep junctions of
concrete & masonry, grouting then back by mortar mixed with non shrinking compound
along with packing of clean, fresh square cut aggregate; also providing and fixing 20
gauge GI chicken mesh @ 150 mm wide to junctions of concrete and masonry, preparing
jambs, sills, grooves, pattas, wattas, rounding of corners, etc. all complete as per
architectural drawings, specifications and finished smooth with wooden rundha etc. or
as specified by the PM at all leads,depth and lifts, doing independent double-legged
scaffolding, cleaning of surfaces, curing, etc. complete as per specification and to the
approval of the PM.
(Location : Internal Wall surfaces)
Sqm
16
Providing and applying plastic emulsion paint of approved make and colour conforming
to IS in two coats (surface and finish acceptable to the PM must be achieved by the
contractor and any additional coats if required shall be at the cost of the contractor);
including preparing surfaces, filling up with gypsum or approved crack filler, binder;
cleaning and making the surface dust-free, applying a sealer or primer coat of paint as
recommended by approved paint manufacturer, applying two coats of paint (of approved
make and shade), required scaffolding, cleaning and protecting till the handing over of
site to the employer all complete to entire satisfaction of the PM. (Location:Internal
walls)
Sqm
17 Providing concrete of grade M25 platform base for Linac Machine and Chiller Cum
18 Fabrication, Supply and Fixing inposition all works complete of Light duty MS Grating
with one coat of Primer and two coats of Finished Paint RMT
Sr.
No. Item Description Qty. Unit
Unit Rate in
Rs.
Total Amt in
Rs.
19
Providing and fixing 600mm x 600mm x 15mm thick Mineral fibre grid false ceiling
system as manufactured by M/s. Armstrong or equivalent approved; fixed using hot
dipped galvanized steel section, exposed surface with pre-coated cappings, tees,
rotary stitched cross tees, sub cross tee and wall angle fixed to the periphery of the wall.
The grid shall be suspended at every 1200mm c/c. in both directions using 2.0 mm.
thick pre-straightened GI wire, including cutting and making arrangement with
required reinforcement, to fix light fillings, AC grills, access services doors/panel
required double legged scaffolding / staging, finishing joints smooth to correct line and
level complete having 3 coats of white paint back of the tile duly sanded and finished
with a coat of protective paint over the formed grid complete all as per approved
reflected false ceiling layout to approval and satisfaction of the PM.
Sqm
20 Supply of Modular flush door with frame approx size 900 X 2100mm with 35 mm thick
solid wood, including lock, handle, keel and other accessories for inner main door. No
21
Providing and fixing 35mm thick flush door shutters single leaf / Double leaf of solid
core of block board type bonded with phenol formaldehyde synthetic resin thermo
pressed with 8 mm thick teak wood tongue & groove external lipping. The construction
procedure of the shutter should be as per IS 2202. The shutter shall be shop prepared
for taking mortice lock or latches suitable lock block of wood may be provided for fixing
the hardware. The size of block, shall perfectly correspond to the maximum size of lock,
covered in IS 2209. All the four edges of the door shutter shall be square. The shutter
shall be free from twist or warp in its plane and of required size etc. complete as
directed.Rate shall include for supplying and fixing the door with necessary approved
hardwares such as S.S.ball bearing Hinges of satin finish of suitable size and thickness
with S.S.Screws, Mortice Lock with handle, lever handle with lock, SS forend and SS
strike plate, europrofile cylinder, all of Satin finish Grade SS 304 confirming to BS
7352 , door closer with Paralel arm bracket in Active Leaf , stainless steel tower bolt,
S.S latches, door stoppers, door buffers etc. complete and as directed and all as per the
approved make and model as mentioned in the drawing
No
Sr.
No. Item Description Qty. Unit
Unit Rate in
Rs.
Total Amt in
Rs.
22
Providing and laying approved quality, colour, design and shade fully homogeneous
Vitrified tile 600mmx600mm (confirming to IS 15622 / EN 176 Group B1a and water
absorption less than 0.08%) flooring in pattern as detailed in drawing or as directed by
the PM. Tile to be bedded over cement concrete screed using approved quality
compatible adhesive of approved make, joints to be cleaned and grouted with matching
colour approved quality polymer based readymade grout, curing, cleaning etc. to
required line, level, etc. all complete at all heights, lifts and leads to the entire
satisfaction of the PM. The tile should be grouted having 5mm epoxy filler of approved
shade as per tile color .
Sqm
23
Providing and laying approved quality, colour, design and shade fully homogeneous
Vitrified tile 300mmx300mm (confirming to IS 15622 / EN 176 Group B1a and water
absorption less than 0.08%) flooring in pattern as detailed in drawing or as directed by
the PM. Tile to be bedded over cement mortar 1:3, joints to be cleaned and grouted with
matching colour approved quality polymer based readymade grout, curing, cleaning etc.
to required line, level, etc. all complete at all heights, lifts and leads to the entire
satisfaction of the PM. The tile should be grouted having 5mm epoxy filler of approved
shade as per tile color .
i For Machine Room Sqm
ii For TPS Room
Sqm
24
Providing and applying plastic emulsion paint of approved make and colour conforming
to IS in two coats (surface and finish acceptable to the PM must be achieved by the
contractor and any additional coats if required shall be at the cost of the contractor);
including preparing surfaces, filling up with gypsum or approved crack filler, binder;
cleaning and making the surface dust-free, applying a sealer or primer coat of paint as
recommended by approved paint manufacturer, applying two coats of paint (of approved
make and shade), required scaffolding, cleaning and protecting till the handing over of
site to the employer all complete to entire satisfaction of the PM. (Location:Internal
walls)
Sqm
25 Supply of working table in control console area 12' X3' X 3'.6" Nos
26 Wooden almirah inside linear accelerator room of size 6’ X 7’ X 2’ Nos
27 Supply of over head cabinet 12' X 2'.6" X2' Nos
Sr.
No. Item Description Qty. Unit
Unit Rate in
Rs.
Total Amt in
Rs.
28 Wooden table 20 RFT for TPS room
Nos
29 Storage cabinet for TPS room 20RFT.
Nos
30 Supply of Chairs
Nos
32
Designing, providing and laying proprietary chemical water proofing system consisting
of polymer modified acrylic base composite coating (of one part or two part component)
as approved by the Client and as recommended by the approved manufacturer of
waterproofing coating, sandwiched nylon mesh / fibre mesh and protective screed. The
work shall include removing of existing waterproofing course, cleaning of surface,
grouting porous surfaces including making ‘V’ grooves at junctions, cracks etc. Further
including horizontal surface protected with 20mm screeding in 1:4 mortar (1 cement : 4
sand) and vertical surface (wall) plastered with cement, sand mortar in ratio 1:4 (1
cement : 4 sand), finished in ready to receive Architectural finish, in correct line, level
and plumb, curing, grouting, testing, etc. all complete to entire satisfaction of the PM,
contractor to provide guarantee for 10 years Rs.100/- stamp paper in approved proforma.
Sqm
34
Making Core Cutting of size 150mm dia in slabs / beams / retaining walls and any other
R.C members to any dia & depth by using 'HILTI' make diamond drilling machine with
tolerance for any type of inserts, anchor fasteners etc. Rate shall include for sealing the
gaps between RC surface and inserts with fire retardent grouting material as per
manufactures specification ,all charge, preparation of surface, cutting of reinforcement,
cleaning the surface, staging, scaffolding with necessary tools and equipments water and
power, removal of debris from the site, staging scaffolding etc complete, as directed.
Nos
35 Co-ordination for Fixing of base frame and Pouring Concrete of grade M25 as directed
by Engineer in Charge Cum
37
Structural Consultancy Fees, including providing Stability Certificate and Test
Certificates from government recognized institutes for Concrete and Steel LS
TOTAL
Sl. No. Description of Item Qty Unit Unit Rate in Rs. Amount in Rs. Total Amount
in Rs.
ELECTRICAL WORKS
Supply Erection Supply Erection
I
SECTION-A: SUPPLY, FIXING, TESTING &
COMMISSIONING MAIN PANEL & DISTRIBUTION
BOARDS
1.1
Supply, Installation, Testing and Commissioning of following LT
Panel shall be designed for 415V, 3 Phase, 50Hz, 4wire A.C
system made up of sheet steel, dust and vermin proof of Cubicle
type, Indoor type, floor mounting, free standing, L.T panel
compartmentalized design and fabricated with 2mm CRCA sheet
steel for main frames, folded sections and load bearing members
and 1.6mm CRCA sheet steel for doors & covers and base
channel 75mm X 40mmX 3mm and removable Gland plates at
bottom and top entry complete with adequate rating of bus-bars,
single bus-bar system, interconnections, cable chamber, powder
coated painting, earthing etc., as mentioned in the Schedule of
quantity / schematic diagram. Providing and fixing of below Panel
with all accessories. The LT panel shall be accommodated in a
modular multi type arrangements, adequate size of cable rack in
cable chamber, painting, Two separate earth bus-bar throughout
the length of the panel, numbering, danger plate etc. as per the
drawings etc as required.
a MAIN LT PANEL
Incomer :
400A TP&N 25KA MCCB1 No with RYB Phase indication
lamps, control MCB and all other required accessories. - 1 No.
Instruments Panel
Digital type Ammeter, Voltmeter, kWH meter, necessary CTs,
and On-Off-Trip trip indicating lamps with control MCB etc.
as per schematic layout.
400A 25 KA TPN Aluminium busbars
Sl. No. Description of Item Qty Unit Unit Rate in Rs. Amount in Rs. Total Amount
in Rs.
Outgoings :
40A TPN MCCB 25KA with all other required accessories - 1
Nos for LDB
63A TPN MCCB 25KA with all other required accessories - 5
Nos for HVAC - 2 nos, PDB - 2 nos & Spare - 1 no
100A TPN MCCB 25KA with all other required accessories - 1
No for Chiller
250A TPN MCCB 25KA with all other required accessories - 1
No for 120KVA UPS
With necessary Aluminium busbar interconnection providing
control MCB, ON, OFF indication lamps etc. for each outgoing
feeders as per schematic layout.
With necessary Aluminium busbar interconnection etc. for each
outgoing feeders as per and schematic layout.
1 Each 0 0 0
b Clinac with OBI Costmer Control Board
Incomer :
250A TPN 25KA MCCB with RYB Phase indication lamps,
control MCB and all other required accessories. - 1 No.
Instruments Panel
Digital type Ammeter, Voltmeter, Earth Falt Relay, necessary
CTs, and On-Off-Trip trip indicating lamps with control MCB
etc. as per schematic layout.
250A 25 KA TPN Aluminium busbars
Outgoings :
100A 25KA 4pole MCCB - 2nos, 100A 4pole power contactor -
2nos
24VDC aux Contactor - 5 Nos, 110VAC aux contactor - 4 nos,
230VAC aux contactor - 1 no
16A Double pole MCB - 7 Nos, 40A 4P MCB - 2 nos, 230/24v
5A Power supply - 1 No
Sl. No. Description of Item Qty Unit Unit Rate in Rs. Amount in Rs. Total Amount
in Rs.
With necessary Aluminium busbar interconnection providing
control MCB, ON, OFF indication lamps etc. for each outgoing
feeders as per schematic layout.
With necessary Aluminium busbar interconnection etc. for each
outgoing feeders as per and schematic layout.
1 Each 0 0 0
1.2 DISTRIBUTION BOARDS:
Supply, Installation, Testing and Commissioning of the following
TPN MCB distribution boards shall be designed for metal
door type IP 42 protection, with MCB / Isolator / RCCB / RCBO
as incomer. The distribution boards shall be designed for
415V,3Ph,50Hz, 4 wire AC system sheet steel, dust and vermin
proof suitable for wall mounting type (recessed) designed and
fabricated made up of Standard reputed make manufacture. The
DB shall have suitable neutral and earth terminal block to
facilitate easy termination of wires. All wires inside the DB shall
be terminated using copper crimping socket. The DB shall be
suitable body earthing terminals with powder coated painting,
danger board, sign writing including minor civil works (recessed
system) etc as required.
a LDB 1
The double door type 4 Way TPN Compartmental
Horizontal ( 7 Segment Phase Segregation ) MCB DB
comprising of the following :
Incoming
32 A TPN MCB 'C' Curve – 1 No.
Outgoings
32 A DP 30 mA RCCB – 3 Nos. as outgoing with 12 Nos 6A SP
MCB 'C' Curve
(Each 32A DP 30 mA RCCB consist of 4 Nos of 6A 10 KA SP
MCB 'C' Curve )
Sl. No. Description of Item Qty Unit Unit Rate in Rs. Amount in Rs. Total Amount
in Rs.
With necessary tinned copper busbars, interconnections, separate
earth bus, separate neutral bus for each phases. The
board shall be powder coated type fixed with concealed system in
wall. The rate shall include necessary connected civil works like
chipping, rough plastering to match with good orginal surface etc.
1
Each
0
0
0
b PDB (Bunker & TPS Room)
The double door type 6 Way TPN Compartmental
Horizontal ( 7 Segment Phase Segregation ) MCB DB
comprising of the following :
Incoming
63A TPN 10kA MCB'C'Curve with all other required accessories – 1
No.
Outgoings
63 A DP 30 mA RCCB – 3 Nos. as outgoing with 9 Nos 16A & 3 Nos
SP MCB 'C' Curve
(Each 63A DP 30 mA RCCB consist of 6 Nos of 10/16/20A 10 KA SP
MCB 'C' Curve )
With necessary tinned copper busbars, interconnections, separate earth
bus, separate neutral bus for each phases. The
board shall be powder coated type fixed with concealed system in
wall. The rate shall include necessary connected civil works like
chipping, rough plastering to match with good orginal surface etc.
2
Each
c UPS DB - Bunkar & TPS Room
The double door type 4 Way TPN Compartmental Horizontal (
7 Segment Phase Segregation ) MCB DB comprising of the
following :
Incoming
32 A TPN MCB 'C' Curve – 1 No.
Sl. No. Description of Item Qty Unit Unit Rate in Rs. Amount in Rs. Total Amount
in Rs.
Outgoings
32 A DP 30 mA RCCB – 3 Nos. as outgoing with 12 Nos 6A SP
MCB 'C' Curve
(Each 32A DP 30 mA RCCB consist of 4 Nos of 6A 10 KA SP MCB
'C' Curve )
With necessary tinned copper busbars, interconnections, separate earth
bus, separate neutral bus for each phases. The
board shall be powder coated type fixed with concealed system in
wall. The rate shall include necessary connected civil works like
chipping, rough plastering to match with good orginal surface etc.
2
Each
1.3 63A 4P MCB & IP 65 Encloser
Supply, Installation, Testing and Commissioning 40/63A TPN MCB
with water proof enclosure including earthing and all other
required accessories as per site conditions. For A/C & Chiller
3
Each
1.4 120 KVA UPS Input & Output Switch
Supply, Erection, Testing and Commisioining of 250A 25KA TPN
MCCB with cubicle type free standing IP 42 Protection encloser with
support clamps and angles frames as required as per the site condition.
Incoming and outgoing cables shall be of Top and bottam entry
(Optional)
2
Each
SECTION - A:-Total C/o to summary : Rs.
II SECTION-B: WIRING AND CONNECTED ACCESSORIES
2.1 SUBMAINS UPS & RAW POWER CIRCUTS
Sl. No. Description of Item Qty Unit Unit Rate in Rs. Amount in Rs. Total Amount
in Rs.
a Supply & Laying of 2R 2.5sqmm 1R 1.5 PVC insulated multistrand
copper wire with 25mm dia PVC conduit with all accessories as
required as per site conditions.(lighting circuit mains)
100 Mtr.
b Supply & Laying of 2R 2.5sqmm 1R 1.5 PVC insulated multistrand
copper wire with 25mm dia PVC conduit with all accessories as
required as per site conditions.(Raw Power Circuit)
95 Mtr.
c Supply & Laying of 2R 2.5sqmm 1R 1.5 PVC insulated multistrand
copper wire with 25mm dia PVC conduit with all accessories as
required as per site conditions.(Ups Circuit)
450 Mtr.
d Supply & Laying of 2R 4sqmm 1R4sq.mm PVC insulated FRLS
multistrand copper wire with 25mm dia FRPVC conduit with all
accessories as required as per site conditions.(Split A/C & 16A
Power Socket Circuit)
150 Mtr.
e Supply & Laying of 12R 1.5sq.mm PVC insulated multistrand copper
wire with 25mm dia PVC conduit with all accessories as required as
per site conditions. (for CCP to Door InterLock and Warning
Lamp control wiring)
55 Mtr.
f Supply & Laying of 12C 1.5sq.mm PVC insulated multistrand copper
wire with 25mm dia PVC conduit with all accessories as required as
per site conditions. (for CCP to Modulator Interphase wiring)
12 Mtr.
g Supply & Laying of 2 Run 1.5sqmm PVC insulated multistrand
copper wire with 20mm dia PVC conduit with all accessories
for Emergency push button wiring.
90 Mtr.
2.2 LIGHT POINT
Sl. No. Description of Item Qty Unit Unit Rate in Rs. Amount in Rs. Total Amount
in Rs.
Provide all materials, accessories, labour etc. for wiring with conduit
and accessories in recessed system wiring for lights,
ceiling fan & exhaust fan point wiring. using 3 Runs of 1.5sqmm PVC
insulated multistrand Flexible copper conductor wires (FRLS) of
650/1100V grade drawn through rigid PVC conduit with 2mm wall
thickness including supply and laying of conduits and its accessories
concealed in the slab / wall, surface mounted / using PVC pull /
junction boxes, light outlet boxes, G.I.switch outlet boxes, Modular
switch plates, 6A switches in recessed system of G.I / Nickel
Cadmium outlet box etc., including testing and commissioning
complete wiring system. The rate for point wiring should inclusive of
supply and fixing of 6A modular type switch in a suitable size
modular box in concealed system, wiring from first switch point and
then looping between the points and switches. Connect the all lights,
switches sockets with suitable PVC sleeves etc as required in the
following manner.
a 1 Light controlled by 1 switch 20 Pts
b 2 light points controlled by 1 switch (1set = 2 lights) 12 Pts
c 4 light points controlled by 1 switch with 400W Dimmer 1(1set = 4
lights) - for Dimmer 1 Pts
2.3 SOCKETS
a
Supply, fixing, testing & commissioning of 6A, multipin shuttered
socket outlet controlled by one way 6A switch. The rate shall be
inclusive of G.I / Nickel Cadmium metal box, modular front plate,
switches & socket and necessary fixing accessories. In recessed
mounting system with civil works (cutting, chipping, plastering to
match the original finish as required. (Consol & Bunker Raw
Power)
6
Nos
b
Supply, fixing, testing & commissioning of 6/13A, multistandard
shuttered socket outlet controlled by one way 6A switch. The
rate shall be inclusive of G.I / Nickel Cadmium metal box, modular
front plate, switches & socket and necessary fixing accessories. In
recessed mounting system with civil works (cutting, chipping,
plastering to match the original finish as required. (Consol & Bunker
UPS Power)
30
Nos
c
Supply, fixing, testing & commissioning of 6/16A, multipin shuttered
socket outlet controlled by one way 16A switch. The rate
shall be inclusive of G.I / Nickel Cadmium metal box, modular front
plate, switches & socket and necessary fixing accessories. In recessed
mounting system with civil works (cutting, chipping, plastering to
match the original finish) as required. (Consol, Bunker & TPS
Room UPS & Raw Power)
15
Nos
d
Supply, fixing, testing & commissioning of 1No 25A 3 Pin socket with
plug top and controlled by 25A DP 'C' Curve MCB in a suitable size
MS enclosure with necessary making interconnection, wiring, earthing,
painting etc., and required fixing accessories. (Splite AC Control)
7
Nos
SECTION - B:-Total C/o to summary : Rs.
III SECTION - C : SUPPLY, FIXING, TESTING & COMMISSIONING
OF LIGHT FITTINGS
3.1 Light Fittings
a
Supply,Erection, Testing and Commissioning of 2' X 2' LED 40 watts
recessed mounting fitting with all accessories and
interconnecting with 3 R 1.5 sqmm PVC insulated FRLS copper wire
Make: Philips, other branded first class companies preferred.
15
Nos
b
Supply,Erection, Testing and Commissioning of LED 18 watts recessed
mounting down light fitting with all accessories and
interconnecting with 3 R 1.5 sqmm PVC insulated FRLS copper wire
Make: Philips, other branded first class companies preferred.
10
Nos
c
Supply,Erection, Testing and Commissioning of single 15W Recessed
fixed type LED Dimmer fitting with Electronics ballast
and all accessories and interconnecting with 3 core 1.5 sqmm PVC
insulated FRLS copper wire and fixing the same in the
Ceiling
4
Nos
d
Supply, Erection, Testing and Commisioining of Box type 28W T5
fitting along with 1 nos 28w Compact Fluorescent Lamps
and with high frequency electronic ballasts with all accessories.
6 Nos
SECTION - C :- Total C/o to summary : Rs.
IV SECTION - D : SUPPLY, LAYING, FIXING, TESTING &
COMMISSIONING LT CABLES AND CABLE TERMINATION
4.1 L.T.CABLES
Supply, Laying, Testing and Commissioning of the following size PVC
insulated and PVC sheathed/XLPE Power cable of
1.1KV grade Aluminium/Copper armoured/unarmoured LT UG cables.
The Cables shall be laying in the cable trenches/cable tray/ground/hume
pipes/cable duct and partially laid on wall/ceiling indoor/outdoor with
suitable clamps & necessary fixing accessories etc. as required.
a 4C 300 sq.mm Aluminium Ar. Cable for EB Incomming power
(Optional) Mtr.
b 4R 95 sq.mm Copper flexible cable UPS Incoming & Outgoing
16 Mtr.
c 4R 95 sq.mm Copper flexible cable for UPS to Clinac with OBI
Costmer Control Board 50 Mtr.
d 4R 35 sq.mm Copper flexible cable for CCP to Modulator
35 Mtr.
e 1C 95 sq.mm Copper flexible cable for additional Netural Earth and
Bodi Earth for 60KVA UPS & Machine 100 Mtr.
f 1C 35 sq.mm Copper flexible cable for Bodi Earth for Machine
35 Mtr.
g 4C 16 sq.mm Copper Ar. Cable for Chiller incoming
75 Mtr.
h 4C 10 sq.mm Copper Ar. Cable for PDB & Duct A/C incoming 150 Mtr.
i 4C 6 sq.mm Copper Ar. Cable for LDB & UPS DB incoming 125 Mtr.
4.2 CABLE TERMINATION
Supply, Installation and making of LT UG cable end termination of the
following size PVC insulated & PVC sheathed /XLPE insulated
Copper/Aluminium cable of 1.1KV grade with single compression
cable gland and suitable Aluminium/Copper crimpping
sockets/lugs,including Gland earth clip ,crimpping paste, sleeves,
ferrules etc., necessary accessories as required.
a 4 Core 300 Sqmm XLPE Ins.Ar.Alu. Cable 2 Each
b 4R 95 Sqmm Copper flexible cable
4 Each
c 4R 35 Sqmm Copper flexible cable
2 Each
d 1R 95 Sqmm Copper flexible cable 6 Each
e 1R 35 Sqmm Copper flexible cable 4 Each
f 4 Core 16 Sqmm Copper Ar. cable 2 Each
g 4 Core 10 Sqmm Copper Ar. cable 12 Each
h 4 Core 6 Sqmm Copper Ar. cable
12 Each
SECTION - D :- Total C/o to summary : Rs.
V SECTION-E: EARTHING SYSTEM, CABLE TRAY WORKS
5.1 Earth stations
a
Supply, Installation, Testing & Commisioning of 3 mtrs long 100mm
dia cast Iron pipe with 600 X 600 X 3mm copper plate
Earth electrode for Machine body earth & UPS Netural earth 3 Each
c Supply and laying of following flats for Earthing 25 x 3 mm GI flat for
main panel and other bodi earthing as required. 75 Mtr.
e
Supply and laying of following Earthing No '8' gauge Copper wire for
equipment and DB, AC & Chiller earthing. 150 Mtr.
5.2 Earth Links
Supply, Fixing of the following size Copper flat earth Station with 2
Nos DMC supporting Insulator clamp with predrilled machine made
holes of 12mm & 6 mm dia at 25mm intervals for fixing earth flat
including Nuts,Bolts & spring and plate washers complete as required.
(2Nos DMC supporting insulators shall be used for 400mm distance)
a 300 x 25 x 3mm thick copper earth flat
2 Each
5.3 CABLE TRAY
a
Supplying, fabricating, erecting and connecting the following 1.6mm
thickness GI perforated type cable trays with necessary
supports, tees, elbows, bends,bolts and nuts and any other associated
accessories to complete the job.-300mm (wide) X
50mm (collar height)
25
Mtr.
SECTION - E:-Total C/o to summary : Rs.
VI SECTION-F - SUPPLY, LAYING, FIXING, TESTING &
COMMISSIONING OF DATA, VOICE & Network
6.1 Supply, Laying & fixing of CAT6 unarmoured Data cable from Data
Rack Box to floor junction box & each individual Sockets
through existing rigid, PVC conduit with all accessories etc.
450 Mtr.
6.2 Supply, Laying & fixing of 2 pair unarmoured telephone cable from 20
Pair Krone connector Box to floor junction box & each
individual Sockets through existing rigid, 2mm thick PVC conduit with
all accessories etc.
100 Mtr.
6.3
Supply & fixing of type data socket outlet recessed mounted system on
a GI / Nickel Cadmium outlet box with UTP CAT6
Shuttered Flush mount with face plate in the exising metal box and all
necessary accessories complete as required including the termination of
wires.
24
Nos
6.4
Supply & fixing of type Voice socket outlet recessed mounted system
on a GI / Nickel Cadmium outlet box with UTP RJ11 IO
Shuttered Flush mount with face plate in the exising metal box and all
necessary accessories complete as required including the termination of
wires.
6
Nos
6.5 Supply,Fixing, Testing and Commissioning of 6U Communication
Rack 1 Nos
6.5 Supply & Fixing of 24port Patch panel and 10/100/1000 mbps Base T
Switch with 24 port patch panel 1 Nos
6.6 Supply of 1 mtr Patch card
24 Nos
6.7 Supply & Fixing of 105 X 50 mm CMS Tray for Electrical, Data &
Voice cable pulling 25 Mtr.
SECTION - F :- Total C/o to summary : Rs.
VII SECTION - G - SUPPLY AND FIXING OF CCTV, FIRE ALARM,
LMO, WARNING LIGHT, EMERGENCY SWITCH & DOOR
INTER LOCK & MISCELLANEOUS
7.1 CC TV
a Supply, Fixing, Testing & Commissioning of Weather Proof IR
Camera, Sony CCD 1/3” colour camera
1 Nos
b Supply, Fixing, Testing & Commissioning of PTZ Doom Camera Sony
CCD 420TVL, X22 Zoom, 3.9 - 8.5 mm Auto iris lens,
RS485 Control
1 Nos
c Supply, Fixing, Testing & Commissioning of PTZ keyboard with
joystick
1 Nos
d Supply, Fixing, Testing & Commissioning of 24” LED Monitor / TV 2 Nos
e Supply, Fixing, Testing & Commissioning of 12VDC 2A power supply
for camera
2 Nos
f Supply and laying of 1 + 3 RG 59 CCTV cable 100 Mtr.
7.2 Tack / Tack Back System
a Supply, Fixing, Testing & Commissioning of Tack / Tack Back
Systems comprises of Console with Mike ( inbled amp.) Ceiling
Speaker - 1no.
1 Set
b Supply and laying of two core screened cable 50 Mtr.
7.3 Fire Alarm System
a Supply, Fixing, Testing & Commissioning of 2 Zone Conventional Fire
Alarm Panel with complete set. (RAVEL Make)
1 Nos
b Supply, Fixing, Testing & Commissioning of conventional Smoke
Detectors with base (SYSTEM SENSOR Make)
6 Nos
c Supply, Erection, Testing & Commissioning of Conventional Manual
Call Point.(RAVEL Make)
1 Nos
d Supply, Erection, Testing & Commissioning of Conventional Hooter/
Sounders (RAVEL Make)
1 Nos
e Supply and Laying of 2 core 1.5 sqmm Copper armoured cable (Policab
Make)
125 Mtr.
7.4 Emergency Switch, LMO & Warning Light
a Supply & Fixing of Emergency Stop switch and system On switch with
base box
4 Nos
b Supply and fixing of Magnetic Door switch 2 Nos
c Supply,Erection, Testing and Commissioning of Warning Lamp for
RED,Yellow,Green & Red, Green for OBI
1 Nos
d Supply of Last man out control unit, Last man out switch with
indicator, buzzer and External wiring kit (1.0 sq.mm cu. Wire &
pipes)
1 Nos
7.5
Installation testing and commissioning of Reynold or other equivalent
make 10TR Chiller with ancillary work such as piping ,
inbuilt 60 later water tank, valves, Grundfoss/wilo make pumps, LP,HP
pressure switch, flow switch, Antifreeze protection, Alarm with buzzer,
ext as per the standard. Including lifting and shifting of chiller with
crane
1
No
7.6 PROFESSIONAL CHARGES:
Towards professional charges for filing application, preparation of
drawings in necessary formats for approval, follow up and arranging
approval of drawings, scheme by Local electricity authority / Electrical
Inspectorate, arranging inspection, obtaining safety certificate clearance
from electrical Inspectorate for the installation and arranging power
connection. The Rate shall be including preparation and submission of
as built drawings of entire installation of the works executed need to be
submitted in the blue print of A1 size as required in 7 Sets of hard copy
and two set sets of soft copy in CD.
1
Job
SECTION - G :- Total C/o to summary : Rs.
Recommended Makes of EquipmentsFor Electrical Works:
1 MCB / MCCB / RCCB/RCBO - HAVELLS / HAGER / LEGRAND
2 Distribution boards - HAVELLS / HAGER / LEGRAND
3 Indicating instruments - DIGITAL - MECO/RISHABH/L&T /
HPL 4 Control Switch / Indication Lamp/ Push
Button
- L&T/SIEMENS/TEKNIC / KAYCEE
5 CTs (epoxy resin cast) - AE / KAPPA/PRECISION/KALPA
6 PVC conduit & accessories - PRECISION/AVONPLAST
7 LT Cables - POLY CAB /HAVELLS /KUNDAN
8 Modular Switch & Switch box [UL, CE
CERTIFIED]
- CRABTREE / LEGRAND/ MK
9 Industrial Type Sockets / Tops - CLIPSAL / HENSEL / LEGRAND
10 FRLS PVC ins. multi-strand copper wires/
Conductors
- POLY CAB /HAVELLS /KUNDAN
11 Light fittings - WIPRO/PHILIPS/HAVELLS/CGL
12 MDF - KRONE
13 Cat 6 utp cables - D-LINK / AMP/3 COM / NETGEAR
14 RJ 45 Computer Jack - D-LINK / AMP/3 COM / NETGEAR
15 Exhaust / Ceiling Fans - ALMONARD / CROMPTON / ORIENT
Note:
1. The Successful Tenderer shall submit test reports for all the materials/equipments.
2. If any make is not in accordance with the tender specification it will not be accepted even if
the make is indicated in the above List.
3. The Client / Consultants reserves the right to reject or accept any of the make given above
without assigning any reasons & bound to supply other brands in the list.
4. Successful Tenderer shall assess the required materials before procurement @ site. on this
account will be recovered in full in their bill.
5. Any excess material brought to site shall be taken back, if any payment made on this account
will be recovered in full in their bill.
All other terms and conditions in the original tender documents remain same as unchanged.
Dated 10/01/2017. The Director