WIRE ROPE CUTTING CHARTWIRE SIZE SOFT EYE HARD EYE

6 MM 0.34 MTR 0.22 MTR9 MM 0.68 MTR 0.35 MTR

10 MM 0.68 MTR 0.35 MTR12 MM 0.68 MTR 0.35 MTR13 MM 0.80 MTR 0.45 MTR14 MM 0.93 MTR 0.50 MTR16 MM 0.95 MTR 0.50 MTR19 MM 1.16 MTR 0.65 MTR22 MM 1.25 MTR 0.72 MTR26 MM 1.56 MTR 0.86 MTR28 MM 1.67 MTR 0.92 MTR32 MM 1.85 MTR 1.06 MTR36 MM 2.10 MTR 1.30 MTR38 MM 2.20 MTR 1.30 MTR44 MM 2.66 MTR 1.60 MTR

52 MM 3.00 MTR 1.80 MTR

BOW DIA X PIN DIA TONNE BOW DIA X PIN DIA0.33 TON 5 mm x 6 mm0.5 TON 6 mm x 8 mm

0.75 TON 8 mm x 10 mm1 TON 10 mm x 12 mm

1.5 TON 12 mm x 13 mm2 TON 13 mm x 16 mm

3.25 TON 16 mm x 19 mm4.75 TON 19 mm x 22 mm6.5 TON 22 mm x 26 mm

1" X 1-1/8" 8.5 TON 26 mm x 28 mm9.5 TON 28 mm x 32 mm12 TON 32 mm x 36 mm

13.5 TON 36 mm x 38 mm17 TON 38 mm x 42 mm25 TON 44 mm x 52 mm

2" X 2-1/4" 35 TON 52 mm x 58 mm55 TON 64 mm x 70 mm

3/16" X 1/4"1/4" X 5/16"5/16" X 3/8"3/8" X 7/16"7/16" X 1/2"1/2" X 5/8"5/8" X 3/4"3/4" X 7/8"

7/8" X 1"

1-1/8" X 1-1/4"1-1/4" X 1-3/8"1-3/8" X 1-1/2"1-1/2" X 1-5/8"

1-3/4" X 2"

2-1/2" X 2-3/4"

CAPACITY CHART FOR WIRE ROPE SLINGS - STEEL CORE

SAFETY FACTOR 5:1 STD: BS EN 13414-1:2003(E)

SAFE WORKING LOAD OFFSHORE WORKING LOAD (SWL) (OSWL) OR DYNAMIC FACTOR

1 LEG 2 LEG 3 LEG 4 LEG 1 LEG 2 LEG 3 LEG 4 LEG8 0.75 1.0 1.5 1.59 0.95 1.3 2.0 2.0 NOT ALLOWED IN OFFSHORE

10 1.1 1.6 2.4 2.411 1.4 2.0 3.0 3.012 1.7 2.3 3.5 3.513 2.0 2.8 4.1 4.1 1.54 1.4 2.05 2.0514 2.25 3.15 4.8 4.8 1.73 1.57 2.4 2.416 3.0 4.2 6.3 6.3 2.3 2.1 3.15 3.1518 3.7 5.2 7.8 7.8 2.85 2.6 3.9 3.919 4.2 5.8 8.8 8.8 3.23 2.9 4.4 4.420 4.6 6.5 9.8 9.8 3.5 3.25 4.9 4.922 5.6 7.8 11.8 11.8 4.3 3.9 6.7 6.724 6.7 9.4 14.0 14.0 5.15 4.7 8.38 8.3826 7.8 11.0 16.5 16.5 6 6.15 10.7 10.728 9.0 12.5 19.0 19.0 6.92 7.3 13.0 13.032 11.8 16.5 25.0 25.0 9.07 10.7 20.6 20.636 15.0 21.0 31.5 31.5 11.5 15.2 31.5 31.538 16.9 23.6 35.5 35.5 13 18.5 35.5 35.540 18.5 26.0 39.0 39.0 14.23 22.2 39.0 39.044 22.5 31.5 47.0 47.0 17.3 31.5 47.0 47.048 26.0 37.0 55.0 55.0 20.0 37.0 55.0 55.052 31.5 44.0 66.0 66.0 24.23 44.0 66.0 66.056 36.0 50.0 76.0 76.0 27.69 50.0 76.0 76.060 42.0 58.0 88.0 88.0 32.3 58.0 88.0 88.0

UP TO AND INCLUDING 10 TON DYNAMIC FACTOR IS TWICE FROM 11 TON & UP TO AND

SLING (MM)

INCLUDING 30 TON DYNAMIC FACTOR IS 2-(0.0416 X (16)EXCEEDING OR AFTER 30 TON DYNAMIC FACTOR IS SAME AS SWLSWL FOR 6 MM WIRE ROPE IS 350 KGS.

WORKING LOAD LIMIT FOR G80 CHAINSTD: BS EN 818 - 4ALL GENERAL PURPOSE SLINGS SHOULD BE RATED BY THE UNIFORM LOAD METHOD AS SHOWN IN THE TABLE

CHAIN SIZE SINGLE LEG TWO LEG THREE & FOUR LEGMM

7 1.5 2.12 1.5 3.15 2.28 2.0 2.8 2.0 4.25 3.0

10 3.15 4.25 3.15 6.7 4.7513 5.3 7.5 5.3 11.2 8.016 8.0 11.2 8.0 17.0 11.820 12.5 17.0 12.5 26.5 19.022 15.0 21.2 15.0 31.5 22.426 21.2 30.0 21.2 45.0 31.532 31.5 45.0 31.5 67.0 47.5

ALL LOADS ARE SHOWN IN TONNES

0 - 45° 45° - 60° 0 - 45° 45° - 60°

INCH MM1/4" 6MM

5/16" 8MM3/8" 10MM1/2" 13MM5/8" 16MM3/4" 19MM7/8" 22MM

1" 26MM1-1/8" 28MM1-1/4" 32MM1-3/8" 36MM1-1/2" 38MM1-5/8" 42MM1-3/4" 44MM

2" 52MM2-1/8" 54MM2-1/2" 64MM

LIST OF STANDARDS

LIFTING EQUIPMENT TYPE REFERENCE STANDARDS

BEAM CLAMP BS EN 13155

CHAIN BLOCK BS EN 13157

CHAIN SLING BS EN 818-4, -5, -6

EYEBOLT / EYENUTS BS 4278

FULL BODY HARNESS BS EN 361

HOOK BS EN 1677-1, 2, 3, 5

LEVER HOIST - CHAIN BS EN 13157

PAD EYES (FABRICATED) LOLER

PALLET TRUCK - HAND OPERATED BS ISO 509, BS EN 1757-2

BS EN 341, 360, 361, 364

PIPE CLAMP / HOOK LOLER

PLATE CLAMP BS 13155

PULLEY BLOCKS / SNATCH BLOCK BS EN 13157

ROUND SLING BS EN 1492 - 2

SHACKLE - ALLOY STEEL US FED. SPEC. RRC-271D

TIRFORS / JAW WINCH BS EN 13157

TROLLEY BS EN 13157

TURNBUCKLES & RIGGING SCREWS BS 4429

WEBBING SLING - FLAT BS EN 1492 - 1

WINCH - HAND OPERATED BS EN 13157

WINCH - ELECTRICALLY OPERATED BS EN 14492

WIRE ROPE - STEEL BS EN 12385 - 1 TO 4

WIRE ROPE SLING BS EN 13414 - 1 TO 3

PERSONNEL PROTECTIVE EQUIPMENT AGAINST FALL FROM HEIGHT