Carbon emission control measures
L. U. Grema1, A. B. Abubakar1, O. O. Obiukwu2
1Department of Mechanical Engineering, Ramat Polytechnic, P.M.B. 1017 Maiduguri, Nigeria
2 Department of Mechanical Engineering, Federal University of Technology, Owerri, Nigeria
ABSTRACT
This paper seeks to share the experience of the Ultra Low CO2 Steelmaking programme
(ULCOS) established in 2002 by a number of EU members on how to cut down CO2 emission by at
least 50 % of the present volume of emission. Global environmental challenge today is the issue of
climate change resulting in devastating effects such as flooding in many countries of the world. One
of the major causes is the CO2 emission from different industries including iron and steel industries.
The total global CO2 emission was put at 29Gt in 2007 and projected to be 37Gt by the 2020. Out of
this volume the steel industry accounts for 3-4 % and this call for concern from stakeholders to come
up with measures to reduce or control the emission of the green house gas. These measures are
necessary considering the growth of the iron and steel industry in the last 50 years. Important items
considered include among others carbon emission and recovery, carbon capture and storage and new
iron and steel making processes and their potential for CO2 reduction.
Keywords: Emission; Ultra Low CO2; Steel Industry; Recovery
1. INTRODUCTION AND METHODS
The struggle for civilization and development is part of human existence. This
historical development has some challenges including the issues of global warming mainly
from industrial emissions which is a major contributor to green house gas (Kawai, 2001;
Losif et al, 2013). Although the topic of discussion here is centered on how iron and steel
industries take measures to cut down CO2 emissions we must start by giving a background
assessment of the magnitude of the problem and its sources. The issue of global warming
started since the industrial revolution of the 19th
century, and this lead to increase in
temperature of the globe (Farla et al, 2013; Chang et al, 2008).
Human activities generate millions of tons of CO2 annually resulting mainly from
industrial emissions whose major source of energy is the fossil fuels (Bonenfant et al, 2009;
Xu and Da-qianq, 2010). The demand for iron and steel has increased tremendously in the
last few decades (Vladimir, 2006). With output reaching well above 1240Mt as of 2006. (Xu
and Da-qianq, 2010). In 2001 Germany alone produced about 52million tons of CO2 from
their industrial production. (Katja and Jayant, 2007). The energy consumption and gas
emission depends on the production capacity of the industries and the type of technology
employed (Katja and Sand, 1998). Production of iron and steel is one of the energy intensive
processes (Katja and Sand, 1998; Katja and Jayant, 2007). The energy consumption of the
steel industry is estimated to be 18-19 EJ or 10-15 % of total global industrial requirements.
International Letters of Natural Sciences Online: 2013-10-27ISSN: 2300-9675, Vol. 3, pp 21-27doi:10.18052/www.scipress.com/ILNS.3.21CC BY 4.0. Published by SciPress Ltd, Switzerland, 2013
This paper is an open access paper published under the terms and conditions of the Creative Commons Attribution license (CC BY)(https://creativecommons.org/licenses/by/4.0)
The global CO2 emission as at 2007 is around 29Gt and is expected to rise by 21 % in
2020.(Xu and Da-qianq, 2010).The steel industries contribute 7 % of global CO2 emission
(Vladimir, 2006).
The production routes determine the amount of CO2 emissions because of the
differences in the raw materials used and the energy inputs (katja and Jayant, 2007).To
protect the environment a high priority is given in the 21st century in that all industrial
activities must be done with environmental consciousness (Kawai, 2001)., and that is the
more reason why most countries involved in iron and steel productions have different internal
environmental laws to tackle the problem of global warming and environmental issues. In
countries like France emission control measures include taxing companies for their emissions
and some legislation are in place mandating companies to include continuous monitoring
equipments of pollutants emitted from the industries, (Lonescu and Candau, 2007).
Fig. 1. ULCOS Program structure (Ulcos, 2013).
The Kyoto protocol was signed in 1997 as a mark of global approach to the issues of
greenhouse gas and how to mitigate it. Implementation of these agreements includes taking
legal actions on member countries who fail to abide by the agreement but not all steel
producing countries accepted including USA and Australia in the decline list (Peter, 2007).
22 ILNS Volume 3
Considering the bulk quantity of emission urgent measures were put in place to tackle the
problem. Some commonly adopted measures include CO2 sequestration, Mineral carbonation
and the use of slag sequestration which is economical as it does not involve transporting CO2
through pipes to reservoir sites. About 0.25 kg of CO2 can be sequestered in 1kg of slag (Xu
and Da-qianq, 2010). Other possible measures to cut down CO2 is to reduce the use of fossil
fuels for example using natural gas instead of coal and a forestation to help reduce CO2
concentration through photosynthesis by the plants (Farla et al, 2013).
The ultra low CO2 steelmaking programme (ULCOS) was established in 2002 by a
number of EU member countries and organizations with the mandate to find ways out on how
to cut down CO2 emission by at least 50 % of the present volume of emission. A lot of
programs are put in place by ULCOS with a view to possible reduction CO2 by improving on
or modifying the process routes in steelmaking. ULCOS for the purpose of efficiency divided
its program into subprojects with each group looking at certain problem area (Xu Da-qianq,
2010; Ulcos, 2013).
2. RAW MATERIALS GOING INTO FURNACE
What materials go in to the furnace determines the amount of greenhouse emission.
Today coal reserves are limited so there is the need for new technologies that dispense coking
and sintering in the production processes. Biomass can replace coal used in both BF and DRI
it is renewable and readily available, CO2 emission from biomass does not add to greenhouse
problems as it is just similar to carbon fixation by plants.
The calorific value of biomass is less than that of coal but it is sufficient to effect
energy conversion. Biomass is a potential reducing agent of iron ores and the weight required
to reduce ore varies with the type of ore used and the purity of the biomass (Vladimir, 2006).
3. CO2 EMISSIONS FROM IRON AND STEEL PRODUCTION
As the demand for iron and steel products has increased in recent years and
consequently this involves the use of large amount of energy, equivalent to 5 % of the
primary energy use in EU and around the globe. The volume of CO2 emitted per ton of steel
is approximately 2200 kg (Xu and Da-qianq, 2010). The emission results from the use of
fossil fuels as a source of energy and carbon as reducing agent (Ulcos, 2013). While energy
required for production depends on process route (Katja and Jayant, 1998; Peter, 2007). For
example the energy utilized in Blast furnace/Basic oxygen furnace is around 17.4 to 18.6
GJ/tcs and that for Electric arc furnace route is 8.3-9.8 GJ/tcs. (Peter, 2007).
The CO2 emission depends on the amount of energy consumed in the different process
routes, for BF/BOF is about 1.8 tons CO2/ts and for EAF is 0.5tons CO2/ts, and more CO2 is
emitted from BF/BOF route than EAF because more than 60 % of steel production is from
BF/BOF route (Vladimir, 2006).
International Letters of Natural Sciences Vol. 3 23
Fig. 2. (Ulcos, 2013.)
The life cycle of steel gives the life pattern of the steel from manufacturing (raw
materials to steel products) through fabrication and application of the product to finally
recycling. It is very important to consider ways of processing steel with little energy input
and low greenhouse gas emission
Fig. 3. Life cycle of steel (Kawai, 2001).
24 ILNS Volume 3
The efficiency of the primary production steps matters in CO2 reduction, what is meant
by efficiency here may include reduced electricity and fuel consumption. In BF emission can
be cut down by substituting coal with hydrogen containing substances like natural gas and
steam and when hydrogen is used to reduce iron ore, the by product is steam and not CO2.
ULCOS proposed the following to curtail CO2 emission problems (USEPA, 2010).
4. CO2 RECOVERY FROM IRON AND STEEL PRODUCTION
Nearly 70 % of carbon that goes into the blast furnace is emitted as gas this explains the
need for recovery. Many recovery techniques are available, the common one is chemical
absorption which is preferably used to recover CO2 reason for choosing it is because CO2 has
a low partial pressure. CO2 recovery is an important step towards reducing greenhouse gas.
Hoogovens group is a very large steel industry in Netherland that recovers large amount of
CO2 emission is recovered and utilized while some quantity being sold out to regional power
stations. The quantity purchased by the regional power station is estimated to be 3.6 Mtons of
CO2 in 1986 alone. More than 75 % of steel industries in Netherlands have incorporated gas
recovery units (Farla et al, 2013).
5. THE CAPTURE AND STORAGE OF CO2
CO2 capture and storage is one of the measures to control greenhouse gas problem. The
gas is captured and stored in special reservoir especially deep aquifers (Xu and Da-qianq,
2010). Since the gas is in a mixed form containing 20 % CO2, 23 % CO, 3 % H2, and 52 %
N2 so it has to be separated and captured and then pressurized and transported before finally
stored in the reservoirs (Xu and Da-qianq, 2010; USEPA, 2010). This practice is acceptable
in recent years and it can be done in one of the following processes (i) the liquid chemical
absorption and ii) the physical absorption and iii) the solid adsorption (Xu and Da-qianq,
2010). The CO2 is well protected by the rocks covering the oil and gas so cannot escape to
the free surface. The oil and gas reservoir is a potential store with capacity of about 140Gton
which is more than 20 times the annual global emission of carbon put at 7Gtons. Another
reservoir is the deep ocean (ULCOS, 2013)., with storage capacity of about 1019 tons
although this is a capital intensive process as it involves laying pipes to reach the deep ocean.
This type of storage is commonly known as carbon dioxide sequestration. Mineralization is
also a CO2 capture process where reaction between the CO2 and magnesium based rocks
converts CO2 into stable carbonates. Slag in steel production is proposed to be used as
reactant to absorb CO2 as follows 1
2CaSio4 + CO2 →CaCO3+
1
2 SiO2 (Xu and Da-qianq, 2010).
6. MODELLING OF INTEGRATED PLANTS
In this modeling gas produced internally are used to generate electricity. The gas is
obtained from the oven furnace and the converter, although not all the gas produced are used
for the electricity generation some are used for heating purposes.
International Letters of Natural Sciences Vol. 3 25
Fig. 4. Internal electricity generation (Losif et al 2013).
The excess gas can be used as energy source for auxiliary units such as steam and lime
production (Losif et al, 2013).
7. DIRECT REDUCTION PROCESS
The direct reduction process is capable of cutting CO2 by 20 % through avoiding some
practices common in the Blast furnace route (Xu and Da-qianq, 2010). This process also
produces DRI using shaft furnace, CO2 from this process are captured and off gas recycled
(ULCOS, 2013).
8. SMELTING REDUCTION PROCESS
This process basically involves the use of molten metal to reduce iron oxide and to
gasify carbonic materials. Environmental emissions are reduced in this process because
coking coal are not used and dispensing sinter plants by using lump ore. A typical type of
these processes includes the Corex, Finex and the HIsmelt, the Corex is developed by
Siemens (Xu and Da-qianq, 2010). In this process pure oxygen is used and off gas can readily
be stored (ULCOS, 2013).
Top Gas Recycled (TGR –BLAST FURNACE):
In top gas recycled blast furnace process CO2 emitted is stored and the remaining gas sent
back into the furnace through the base and act as reducing agent (ULCOS, 2013).
9. CONCLUSIONS
Many countries have taken different measures to deal with the issue of global warming
resulting from their industrial emissions, although this is a broader and more general
approach to the problem as we are only concerned with emissions from iron and steel
industries and specific steps taken by such industries to cut down greenhouse gas. In fact the
steel industries has been confronted with the issue of global warming and most countries
involve in iron and steel production have passed serious internal legislations and are
signatories to international policies to try mitigate the problem.
26 ILNS Volume 3
The setting up of ULCOS as a body responsible for achieving the greenhouse gas cut
down has put in place a lot plans to be implemented by the steel industries. Carbon capture
and storage is seen as the most urgent and more effective way to control CO2 emission
despite problems of implementation in large commercial scale. Secondly the possibility of
using steel slag for CO2 sequestration is also receiving attention where the basicity and
acidity characteristics of the slag play an important role. Here sequestration is achieved
through interaction between the CO2 and cations. Thirdly, CO2 recovery is also one way of
reducing greenhouse emission, majority of CO2 emission take place in the Blast furnace so
recovery from this point is necessary though is capital intensive but it is a wise investment.
References
[1] Bonenfant D., Kharoune L., Souve S., Hausler R., Niquette P., Mimeault M., Kharoune
M., International Journal of Greenhouse Gas Control 3(1) (2009) 20-28.
[2] Chang Y. F., Lewis C., Lin S. J., Energy Policy 36 (2008) 2471-2480.
[3] Farla J. C. M., Hendriks C. A., Blok K., CO2 Recovery from Industrial processes.
Retrieved June 21, 2013 from www.springerlink.com/index/u7075275w920x688.pdf
[4] Kawai J., Materials & Design 22(2) (2001) 111-122.
[5] Katja S. Jayant S. (1998). India’s Iron and Steel Industry. Retrieved June 20, 2013 from
http://ies.lbl.gov/iespubs/41844.pdf
[6] Katja S., Sand R. D., Energy Economics 29(4) (2007) 799-825.
[7] Losif A. M., Birat J. P., Mirguax O., Ablitzer D., Reduction of CO2 Emissions in the
Steel Industry based on LCA Methodology. Retrieved june 20, 2013 from
www.ulcos.org/en/docs/Ref33%20-%20TMS_CO2_correct_1.pdf
[8] Lonescu A., Candau Y., Environmental Modelling & Software 22(9) (2007) 1362-1371.
[9] Peter L., Ecological Economics 63(4) (2007) 799-806.
[10] ULCOS Program Addressing Climate Change Challenge. Retrieved July 10, 2013
www.ulcos.org/en/docs/Ref28%20-%20ISIJ_157_H0053.pdf
[11] U.S. Environmental Protection Agency 2010. Available and Emerging Technologies for
Reducing Greenhouse Gas Emissions from Iron and Steel Industries. Retrieved June 22,
2013 www.epa.gov/nsr/ghgdocs/ironsteel.pdf
[12] Vladimir S., Renewable Energy 31 (2006) 1892-1905.
[13] Xu C., Da-qiang C., Journal of Iron and Steel Research, International 17(3) (2010) 1-7.
( Received 04 October 2013; accepted 26 October 2013 )
International Letters of Natural Sciences Vol. 3 27