SUBMITTAL TRANSMITTAL Date: 6/26/17 Job Name: Trilogy Condominiums To: George Schweikart Number of pages sent: Company: Kilburn Architects Including this page. 14 Reply To: Marc Pevoto Email: [email protected]Supplier: BBH Sheet Metal Copies Pages Spec.No. Description 1 2-5 076200 Shop drawings 6 076200 Color chart 7-9 076200 Kyan 500 specification 10-13 076200 NuRay sample warranty 14 076200 NuRay care and maintenance Architect’s Stamp: Services Contractor Review CDK Construction Submittal # 076200 Job: Trilogy Condominiums X Reviewed F Reviewed/Resubmit F Reviewed with Comments F Other Reviewed for general conformance with the contract requirements. Contractors review does not relieve subcontractor and/or vendor of their responsibility for dimension, quantities, accuracy, or completeness of this submittal or from any responsibility required by the terms and conditions of their contract/purchase order with CDK Construction Services. Date 06/26/17 Reviewed By: Marc Pevoto 1 X George Schweikart 06/28/17 Install per details.Verify conditions in the field. Provide pre-finished "matte black" color coping at roof parapet (see detail 35). Provide pre-primed coping at all partial walls - at deck openings (see detail 37) and at entries. Paint per paint schedule.
X Reviewed Reviewed/Resubmit Reviewed with Comments OtherReviewed for general conformance with the contract requirements. Contractors review does not relieve subcontractor and/orvendor of their responsibility for dimension, quantities, accuracy, or completeness of this submittal or from any responsibilityrequired by the terms and conditions of their contract/purchase order with CDK Construction Services.Date 06/26/17 Reviewed By: Marc Pevoto
1
X
George Schweikart 06/28/17
Install per details.Verify conditions in the field. Provide pre-finished "matte black" color coping at roof parapet (see detail 35). Provide pre-primed coping at all partial walls - at deck openings (see detail 37) and at entries. Paint per paint schedule.
2
3
4
5
Leaf Green ★ ◆
Architectural Color Guide
Hartford Green ★ ◆
Light Brown ●
Moss Green ★ ◆ ●
Weathered Copper ★ ◆ ●
Musket ◆ ●
Tahoe Blue ★ ◆
Dark Bronze ★ ◆
Deep Blue Sea ★ ◆ ●
Matte Black ★ ◆
Charcoal Gray ★ ◆ ●
Colonial Red ★ ◆
Brick Red ●
Redi-Red ★ ◆
Desert Tan ★ ◆ ●
Parchment ★
Regal White ★ ◆ ●Light Stone ●
Zincalume Plus(available in all gauges)
Old Town Gray ★ ◆ ●
Cordovan ★
Metallic Copper Penny ★
Metallic Antique Patina ★
Metallic Pre-Weathered Zinc ★
— PREMIUM FINISHES —
Nu-Ray Metals is an official Energy Star Partner® and manufacturer of Energy Star® rated products.
The colors shown on this card are best-approximations of the true finish colors of our products. Although they are as accurate as technology allows, there will be slight differences compared to actual product finishes.
Key to color availability by gauge: ★ 24 gauge ULTRA-Cool Kynar ◆ 26 gauge Nu-Shield with Teflon® surface protector ● 28 gauge Silcone-Modified Polyester (SMP)
TEFLON® is a registered Trademark of DuPont used under license by NuRay Metal Products, Inc.
6
GS
Roof parapet only
Pre-prime and paintall coping otherthan roof parapet.
GS
Pre Finished Flashing Materials SECTION 07620
Nu Ray Metal Products, INC. • 1234 37th Street NW Auburn, WA 98001 • www.nuraymetals.com
Specification:
A. Pre Finished flashing materials shall be from Nu Ray Metal Products, Inc. Base metal Tru Zinc®Steel. All materials shall be 24 gauge unless otherwise noted on drawings and details. Exposedsurfaces to be coated with PPG ULTRA Cool Kynar 500 coating or a factory primed/paint readycoating as selected by the architect. Kynar 500 coating to contain 70% fluoropolymer basedresin (PVDF). Colors will be selected by the architect from submitted color chart. Verify colors oncolor/finish schedule with architect before ordering materials.
Standard information:
Our 24 gauge materials offer PPG ULTRA Cool Kynar 500 paint system. This system provides outstandingaesthetics, durability, and long term IR reflectivity in a wide range of architectural uses under normalenvironmental conditions. More than 25 years of field use, combined with chemistry that improves theIR reflectivity while not diminishing your options in color, creates a new standard of excellence inarchitectural fluoropolymer finishes.
Important notes:
Contains 70% PVDF40 year warrantySuperior fade/chalk ratingsBacked by a world leader in coatings systemsMeet requirements for:
o LEEDo ENERGY STAR®o AAMA 620/621o Title 24o ASHRAE 90.1
ULTRA Cool are registered trademarks of PPG Industries, Inc.
True Zinc is a registered trademark of BlueScope Steel Limited. Steelscape holds exclusive rights to the True Zinc trademark within the U.S.
7
SYSTEM OVERVIEW
COMMERCIAL USES
DURABILITY
PRODUCT DESCRIPTION
DURANAR ULTRA-Cool fluoropolymer coil coatings are designed to provide outstanding aesthetics, durability, and long term IR reflectivity in a wide range of architectural uses under normal environmental conditions. More than 25 years of Duranar field use, combined with chemistry that improves the IR reflectivity while not diminishing your options in color, creates a new standard of excellence in architectural fluoropolymer finishes. DURANAR ULTRA-Cool coil coatings combine IR reflective pigment technologies and PPG proprietary resin, with 70% of the resin system being fluoropolymer-based. The coatings are highly resistant to chalking, fading, chipping, and peeling when properly applied by an approved applicator. DURANAR ULTRA-Cool coil coatings meet Cool Roof requirements of LEED, ENERGY STAR®, Title 24 and ASHRAE 90.1. PPG has numerous colors registered with the Cool Roof Rating Council and ENERGY STAR. The coatings exceed the requirements of AAMA 620/621 specifications, and are approved for use on properly cleaned and treated aluminum and coated steel substrates such as G90 hot dip galvanized, Galvalume®, and Zincalume®*. They are not intended for use on hot or cold rolled steel substrates for exterior exposure applications.
P R O D U C T D ATA
DURANAR ULTRA-Cool IR reflective
coatings are multi-coat systems consisting
of a nominal 0.2 mil corrosion inhibitive
primer, a 0.75 mil fluoropolymer topcoat,
and a 0.5 mil clearcoat, when applicable.
They are available in a wide range of
consistent, stable colors that meet
ENERGY STAR® requirements for IR
reflective roof products. They are extremely
durable, providing long-term solar
reflectivity as well as resistance to chemical
attack and surface damage caused by acid
rain, salt spray, and humidity encountered
under normal environmental conditions.
DURANAR ULTRA-Cool coil coatings
require minimal maintenance and minor
scratches can be easily repaired in the field.
Cool-roof technology has never been so
easy. The DURANAR ULTRA-Cool
coatings system offers more heat
reflectivity than virtually any other roofing
material available –letting you realize
significant energy savings while enjoying
the choice of a color palette that ranges
from bold and bright to deep and dark.
The effects of DURANAR ULTRA-Cool
coatings will offer potential benefits such
as lower building air conditioning costs,
less product expansion and contraction,
and improved comfort levels for building
occupants. This coating system is an
excellent choice for roof and wall panels.
DURANAR ULTRA-Cool coil coatings are
chemically inert, providing excellent
resistance to color and gloss fade as well as
environmental stress including acid rain and
ultraviolet attack. The coatings require very
little maintenance, and most surface
contaminants may be removed by
conventional detergents or cleaning
solvents. (Harsh chemicals, abrasives or
solvents must not be used on DURANAR
coated surfaces.) All coatings are fully
tested in south Florida for sustainable
solar reflectance prior to approval for use
in any DURANAR ULTRA-Cool coil
coating system. Additionally, DURANAR
ULTRA-Cool coatings are tested at
exposure sites throughout the world in all
types of climatic and industrial conditions
to ensure the coatings’ performance
and durability.
DURANAR®
ULTRA-Cool®
COATINGS
DURANAR , ULTRA-Cool and the PPG logo are registered trademarks of PPG Industries, Inc.The Cooladillo is a trademark of PPG Industries, Inc.
*Galvalume is a registered trademark of BIEC International, Inc. Zincalume is a registered trademark of BlueScope Steel Limited. Steelscape, Inc. holds exclusive rights to the Zincalume trademark within the U.S.
DURANAR ULTRA-Cool coatings are just one of the EcoLogical Building Solutions™ from PPG.
®
8
1 Coated Steel includes the following types of steel: G90 hot dip galvanized, Galvalume, and Zincalume.2 Fracturing or rupturing of substrate will rupture coatings. Heavy gauge and clad steel substrates impose limitations on formability.
PPG Industries, Inc.151 Colfax St.Springdale, PA 15144(800) 258-6398Fax: (724) 274-2600
DURANAR ULTRA-Cool WARRANTY INFORMATIONPPG offers a comprehensive warranty on DURANAR ULTRA-Cool coil coatings. For complete warranty information and a copy of the DURANAR ULTRA-Cool coil coatings warranty, please call PPG at 1-800-258-6398.
P R O D U C T D ATA
DURANAR ULTRA-Cool SPECIFICATIONS
DURANAR®
ULTRA-Cool®
COATINGS
Aluminum Substrate Coated Steel1 SubstrateDry Film Thickness (nominal) ASTM D1400 0.15 - 0.30 mil primer 0.15 - 0.30 mil primer 0.7 - 0.9 mil topcoat 0.7 - 0.9 mil topcoatGloss ASTM D523 @ 60° 25 - 35 25 - 35Solar Reflectance ASTM E903 Steep Slope: >25% Initial; >25% Initial; >15% after 3 years >15% after 3 years Low Slope: >65% Initial; >65% Initial; >50% after 3 years >50% after 3 yearsEmissivity ASTM C1371 0.80 (80%) min. 0.80 (80%) min. E408Pencil Hardness ASTM D3363 F-2H F-2HFlexibility2
T-bend, ASTM D4145 0-2 T-bend; No pick-off 2 T-bend; No pick-offAdhesion ASTM D3359 No adhesion loss No adhesion lossReverse Impact ASTM D2794 No cracking or adhesion loss No cracking or adhesion lossAbrasion, Falling Sand ASTM D968 65-85 l/mil 65-85 l/mil Mortar Resistance ASTM C267 No effect No effect Detergent Resistance ASTM D2248 3% detergent @ 100˚F (72 hrs.) No effect No effect Acid Resistance ASTM D1308 10% muriatic acid - 24 hrs. No effect No effect 20% sulfuric acid - 18 hrs. No effect No effect Acid Rain Test Kesternich SO2, DIN 50018 15 cycles min. 15 cycles min. No objectionable color change No objectionable color change Alkali Resistance ASTM D1308 10%, 25% NaOH, 1 hr. No effect No effect Salt Spray Resistance ASTM B117 No face blistering; None or few #8 blisters; 5% salt fog @ 95°F Max. average 1/16” Max. average 1/8” scribe creep. scribe creep. Passes 4000 hrs. Passes 1000 hrs.Humidity Resistance ASTM D714, Passes 4000 hrs. Passes 1500 hrs. ASTM D2247 No #8 blisters No #8 blisters 100% relative humidity @ 95°FExterior Exposure 10 yrs. @ 45°, south Florida ASTM D2244 Max. 5 fade Max. 5 fade ASTM D4214 Max. 8 chalk Max. 8 chalk
9
NU-RAY METAL PRODUCTS, INC. KYNAR 500 ULTRA-COOL WARRANTY *We Nu-Ray Metal Products, Inc. warrant our Kynar 500 Ultra-Cool coated steel products as follows:
1. SUBJECT OF WARRANTY: This warranty is issued to (NRM Customer): SAMPLE solely for the benefit of (end user): SAMPLE warranty applies only to the Nu-Ray Metal Products (NRM) Kynar Ultra-Cool coating applied to G-90 galvanized or Zincalume coated steel. 2. WARRANTY:
2.1 - NRM warrants that all the Kynar 500 Ultra-Cool coated steel panels that are installed in the United States and Canada shall not: a. Within forty (40) years of date of installation 1. Peel, chip or crack 2. See attached warranty for remedy. b. Within twenty (20) years of date of installation 1. Chalk more than eight (8): as rated by ASTM-D659-80 2. Show a color change of more than five (2) E Unites; as rated by ASTM D 2240-80 3.7.1 and 3.8.1.4. 2.2 – If the coating should fail during the warranty period we Nu-Ray Metal Products, Inc. will repair or replace the panels in question, Nu-Ray Metal Products will:
1. Pay the reasonable cost of refinishing the defective panels. This decision will be determined with an objective evaluation by NRM and NRM customer (contractor): SAMPLE. of the installation whether the panels in question may be refinished or must be replaced. If the (NRM customer): SAMPLE warranty is less than replacement, then NRM obligation shall be reduced accordingly.
2.3 – Recoating of the failed metal shall be performed using standard refinishing practices and materials, not necessarily the NRM Kynar Ultra-Cool standard, at NRM’s discretion.
3. DEFINITIONS: The following terms shall be defined as follows:3.1 – “Chip” – this defect is characterized as a surface paint failure, as shown by paint not adhering, as opposed to physical damage as a result of bumping, nicking and banging. 3.2 – “Crack” – Breaks that occur in flat coated surface resulting from exposure, as compared to those breaks in the film associated with metal forming or fabrication, as seen with the naked eye and which allow the film to be removed by taping. 3.3 – “Abnormal exposure area” – This means any area where corrosive exposure such as, but not limited to, salt spray, strong acid or alkaline emissions; such as oil refineries, paper mills, smelters, and fertilizer plants and similar operations.(Areas of pollution and smog of the normally encountered in commercial, industrial and residential areas are not considered abnormal exposure areas)3.4 – “Blistering” – Areas of the coating that are detached or bubbled from the substrate. 3.5 – “Chalk rating” – ASTM D659-80 3.6 – “Metal perforation” – Holes in the panels caused by corrosion due to paint failure. 3.7 – “Peel” – Area of the metal where the coating fails away due to failure other than by corrosion.3.8 – “White rust” – Oxides of zinc developing as a result of coating protection failure as opposed to other causes. 3.9 – “Color change rating” – Measured after the surface has been cleaned of contaminants in accordance with ASTM D2244-80 3.7.1. and 3.8.1.4.
10
4. CONDITIONS: The foregoing warranty is conditioned upon compliance with each of the following standards.
4.1 – The Kynar 500 Ultra-Cool coating must be applied to a minimum dry film thickness of .8 mil to the weather side of the panel. The Kynar 500 Ultra-Cool paint is to be applied to the properly cleaned and treated galvanized or Zincalume coated steel 4.2 – All claims must be made in writing to the following address within 30 days of the discovered of suspected failure.
Nu-Ray Metal Products, Inc. 1234 37th Street NW Auburn, WA. 98001
5. LIMITATIONS: The foregoing warranty does not apply to:5.1 – Failure due to improper handling of Kynar 500 Ultra-Cool coated materials. 5.2 – Failure from acts of God, improper installation techniques, product installed within 1000 feet of salt water is not covered under this warranty, excluding product installed within the Puget Sound Exclusion area as defined by “Puget Sound Exclusion” below, or physical damage during shipment, handling, physical damage resulting from reactions to harmful chemicals, liquids or gases.
6. PUGET SOUND EXCLUSION: 6.1 - Conditions: Mild Marine - calm salt water near large natural harbors. No breaking surf. For the area defined as the Inner Coastal areas of the Puget Sound, Washington as extending from Bellingham, WA to Olympia, WA. Coastal areas with direct exposure to the Strait of Juan de Fuca West defined as the a line extending north to south connecting from Anacortes, Oak Harbor and Port Townsend, WA are excluded from the warranty and will fall under the Severe Marine Conditions of the standard warranty. The warranty will exclude Industrial Applications.6.2 - For locations located from 0 - 1,000 feet of the coast as defined above the warranty conditions are as follows:
Technology: BASF Standard Ultra-Cool Fluoroceram and Ultramet ColorsYears: 20 Years for Standard Ultra-Cool Fluoroceram and 15 Years for Ultramet Colors Primer Film Thickness: 0.25 mls (standard) Topcoat Film Thickness: 0.75 mls (standard) Film Integrity: 20 Years Standard / 15 Years Ultramet Color dE <= 5.0: 20 Years Standard / 15 Years Ultramet Chalking >=8: 20 Years Standard / 15 Years Ultramet
7. EXCLUSION OF WARRANTIES; LIMITATION OF DAMAGES: 7.1 – Nu-Ray Metal Products, Inc. provides a warranty only as described herein. Nu-Ray Metal Products, Inc. extends no other warranty of any kind, expressed or implied, including but not limited to warranties of merchantability, suitably or fitness for a particular purpose, usage or trade. 7.2 – Nu-Ray Metal Products, Inc. exclusive remedy hereunder is expressly non-conforming goods or parts on the terms and subject to the conditions described herein. 7.3 – The warranty for any repaired, refinished, or replaced material shall be for the remainder of the original warranty period applicable to the original painted metal. Delivery charges, installations cost, and taxes are not covered under this warranty.
8. TERMS OF WARRANTY: 8.1 – If a warranty is required, the customer must notify Nu-Ray Metal Products, Inc. in writing at the time the purchase order is issued. 8.2 – The warranty period shall commence as of Nu-Ray Metal Products, Inc. invoice date provided the original copy of the warranty signed by all parties has as been returned to Nu-Ray Metal Products, Inc within the sixty (60) days of presentation to Nu-Ray Metal Products, Inc. Customer.
11
OWNER: SAMPLE
LOCATION OF PROJECT: 1234 37TH St. Auburn, WA 98001
A. In most areas, normal rainfall is sufficient to keep the metal surface clean. Where an unusual amount of dirt or debris suck as needles, leafs or pollen are deposited on the surface, a simple cleaning procedure should be scheduled annually or more often if conditions demand. The use of ordinary non-abrasive household detergent is recommended.
B. For severe conditions use the following solution: 1/3 cup ordinary non-abrasive household detergent (i.e. Tide) 2/3 cup trisodium phosphate (i.e. Spic N Span) 1 gallon water
CAUTION: Stronger concentrations of cleaners can cause damage to the finish. Rinse the surface with clear water immediately after cleaning. Avoid skin contact or getting the solution in the eyes. Always wash the metal from the bottom to top and keep rinsing thoroughly with fresh water while cleaning.
C. In some areas, mildew may be a problem. It appears as black spots on the surface dirt and is usually detected in areas not subjected to rainfall. For removal, prepare a solution as follows: 1/3 cup powder detergent (i.e. Tide) 2/3 cup powder detergent (i.e. Spic N Span) 1 quart 5% Sodium Hypochlorite (i.e. Clorox) 3 quarts water.
CAUTION: Greater amounts of concentration may cause damage to the finish. Always test any cleaner on an inconspicuous area before application to major areas. Excessive rubbing will crate an undesirable glossy finish.
D. We are pleased to add you to our long list of satisfied customers and we hope you’ll recommend our products to your friends and neighbors. We know you’ll benefit from these prefinished building materials for many years to come and thank you for your purchase.
13
Care and Normal Maintenance Instructions for your:
Nu-Ray Metals
Prefinished Building Materials
A. In most areas, normal rainfall is sufficient to keep the metal surface clean. Where an unusual amount of dirt or debris suck as needles, leafs or pollen are deposited on the surface, a simple cleaning procedure should be scheduled annually or more often if conditions demand. The use of ordinary non-abrasive household detergent is recommended.
B. For severe conditions use the following solution:
1/3 cup ordinary non-abrasive household detergent (i.e. Tide) 2/3 cup trisodium phosphate (i.e. Spic N Span) 1 gallon water CAUTION: Stronger concentrations of cleaners can cause damage to the finish. Rinse the surface with clear water immediately after cleaning. Avoid skin contact or getting the solution in the eyes. Always wash the metal from the bottom to top and keep rinsing thoroughly with fresh water while cleaning.
C. In some areas, mildew may be a problem. It appears as black spots on the surface dirt and is usually detected in areas not subjected to rainfall. For removal, prepare a solution as follows: 1/3 cup powder detergent (i.e. Tide) 2/3 cup powder detergent (i.e. Spic N Span) 1 quart 5% Sodium Hypochlorite (i.e. Clorox) 3 quarts water. CAUTION: Greater amounts of concentration may cause damage to the finish. Always test any cleaner on an inconspicuous area before application to major areas. Excessive rubbing will crate an undesirable glossy finish. D. We are pleased to add you to our long list of satisfied customers and we hope
you’ll recommend our products to your friends and neighbors. We know you’ll benefit from these prefinished building materials for many years to come and thank you for your purchase.
