Specifications Engine Model Cat ® C4.4 Stage IIIA DIT Gross Power 63 kW 84 hp Maximum Torque 353 Nm/1400 rpm Displacement 4.4 litre Weights Operating Weight with Carriage and Forks 5897 kg Operating Specifications Rated Load Capacity 2500 kg Maximum Lift Height 5600 mm Maximum Forward Reach 3250 mm Top Travel Speed 26 km/h Load at Max Height 2500 kg Load at Max Reach 940 kg Turning Radius Over Tyres 3200 mm Turning Radius Over Forks 4254 mm Service Refill Capacities Fuel Tank 91 litre Hydraulic System 98 litre Tyres Standard 14.00 x 17.5 Foam Filled Brakes Service Brakes Inboard wet disc brakes on front axle Parking Brakes Wet disc spring-applied hydraulic release • Light on dash indicates when brake is on. Axles • Planetary on front and rear axles. • High bias limited slip differential on front axle. Hydraulic System — Implement Pump Type Single Section Gear Pump Maximum system pressure 240 bar Maximum Pump Flow 85 litre/min • Auxiliary Hydraulic Circuit used for all attachments equipped with cylinders or other hydraulic components. Consists of valves, controls, and hydraulic lines. Transmission Transmission Hydrostatic Forward Variable Speed Reverse Variable Speed Boom Performance Boom Up 6.2 Seconds Boom Down 4.3 Seconds Tele In 3.4 Seconds Tele Out 6.3 Seconds Bucket Dump 2.0 Seconds Bucket Crowd 2.4 Seconds Drawbar Pull (Loaded) 38.7 kN Instruments • Indicators for machine hours, fuel-level, steer mode, steering pressure, battery charge, coolant temperature, parking brake and engine pre-heat. • Reverse motion alarm. • Panel and switches are illuminated for night operation. Cat ® TH255 Telehandler
WeightsOperating Weight with Carriage and Forks 5897 kg
Operating SpecificationsRated Load Capacity 2500 kgMaximum Lift Height 5600 mmMaximum Forward Reach 3250 mmTop Travel Speed 26 km/hLoad at Max Height 2500 kgLoad at Max Reach 940 kgTurning Radius Over Tyres 3200 mmTurning Radius Over Forks 4254 mm
Service Refill CapacitiesFuel Tank 91 litreHydraulic System 98 litre
TyresStandard 14.00 x 17.5 Foam Filled
BrakesService Brakes Inboard wet disc brakes on front axleParking Brakes Wet disc spring-applied hydraulic release• Light on dash indicates when brake is on.
Axles• Planetary on front and rear axles.• High bias limited slip differential on front axle.
Hydraulic System — ImplementPump Type Single Section Gear PumpMaximum system pressure 240 barMaximum Pump Flow 85 litre/min• Auxiliary Hydraulic Circuit used for all attachments
equipped with cylinders or other hydraulic components. Consists of valves, controls, and hydraulic lines.
CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
2 m
3 m
4 m
5 m
6 m
1 m
0 m
4 m 3 m 2 m 1 m 0 m600 mm
C
DE
BA
0°
10°
20°
30°
40°
50°
60°
70°
940
kg 1500
kg 20
00 k
g 2500
kg
2500 kg
TL255
-1010 20
30 4050 60
7080
TL255
-1010 20
30 4050 60
7080
TL255
-10 10 20 3040 50
60 7080
TL255
Load Chart and Dimensions
AEHQ6033-01 (10-2009)
1920 mm
2290 mm
3660 mm
279 mm
1820 mm
TH255 Telehandler
Dimensions
All dimensions are approximate.
IMPORTANTRated lift capacities shown are with machine equipped with standard carriage and pallet forks. When lifting loads, the machine requires a firm surface with undamaged, properly inflated tyres. Machine specifications and stability are based on rated lift capacities at specific boom angles and boom lengths. (If specifications are critical, the proposed application should be discussed with your dealer.)
DO NOT exceed rated lift capacity loads, as unstable and dangerous machine conditions will result.
DO NOT tip the machine forward to determine the allowable load.
Due to continuous product improvements, machine specifications and/or equipment changes may be made without prior notification. This machine meets or exceeds AS1418.19-2007 as originally manufactured for intended applications.
Cat®
TH336Telehandler
SpecificationsEngineEngine
Standard Cat®C4.4DITAACOptional Cat®C4.4DITAAC-ACERT™
CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
Stabilizers DownStabilizers Up
9 m 8 m 7 m 6 m 5 m 4 m 3 m 2 m 1 m 0 m 9 m 8 m 7 m 6 m 5 m 4 m 3 m 2 m 1 m 0 m-1 m
0 m
1 m
2 m
3 m
4 m
5 m
6 m
7 m
8 m
9 m
10 m
11 m
12 m
13 m
14 m
-1 m
0 m
1 m
2 m
3 m
4 m
5 m
6 m
7 m
8 m
9 m
10 m
11 m
12 m
13 m
14 m
600 mm 600 mm
75°
60°
50°
40°
30°
20°
10°
0°
75°
60°
50°
40°
30°
20°
10°
0°
350
kg50
0 kg
750
kg
1000
kg
1500
kg 25
00 k
g
3700
kg
3000 kg
2000 kg
1250 kg
2500
kg
1000
kg
1500
kg
2500 kg
3700
kg
3000
kg
2000
kg
Load Chart and Dimensions
TH414 Telehandler
Dimensions
All dimensions are approximate.880 mm
2036 mm
2449 mm
2592 mm
1979 mm
3200 mm
458 mm
5091 mm6325 mm
1225 mm
AEHQ6036 02(12-2010)
IMPORTANTRated lift capacities shown are with machine equipped with standard carriage and pallet forks. When lifting a load, the machine requires a firm surface with undamaged, properly inflated tyres. Machine specifications and stability are based on rated lift capacities at specific boom angles and boom lengths. (If specifications are critical, the proposed application should be discussed with your dealer.)
DO NOT exceed rated lift capacity loads, as unstable and dangerous machine conditions will result.
DO NOT tip the machine forward to determine the allowable load.
Due to continuous product improvements, machine specifications and/or equipment changes may be made without prior notification.
This machine meets or exceeds AS1418.19-2007 as originally manufactured for intended applications. When utilising a suspended load, the JLG Load Management Indicator System (LMIS) must be installed in order to remain compliant with AS1418.19-2007.
