Catálogo Kross Parts 2015

OKŁADKA

208

AKCESORIA - WSTĘP

PARTS &ACCESSORIES

AKCESORIA - WSTĘP

PARTS &ACCESSORIES

210

COMPONENTSCOMPONENTS

FRAMES

212

LEVEL B+Level B+ is the top of the line model from the 29ers frames. Dedicated for the most demanding cyclists competing in marathons and cross-country races. The frame was created in collaboration with the leading Polish players of MTB scene - the Kross Racing Team. It was made of advanced carbon fiber Carbon SL, which thanks to the special layering ensure high rigidity at the same time very good damping characteristics while maintaining low weight. The wider seat post and bottom bracket junction strengthens the frame makes it really fast. Short rear triangle and tapered headtube provides very good manoeuvrability on winding paths. High rigidity is also ensured by application of 12 x 142 mm rear axle standard. Direct mount for front derailleur limits the amount of necessary parts. This frame proved its quality on demanding European tracks. In 2014 Kross Racing Team riders on the B+ have been really successful: 2nd during Polish championship XCO in Żerków, 1st during the Academic World Cup XCO in Jelenia Góra, 9th in European Championships XCO in St. Wendel, 1st place in the race Copa Catalana UCI HC in Andorra, 2nd place the race UCI C1 Asvö Österreich Grand Prix in Austria.

Bottom bracket type Press Fit

Bottom bracket width 92 mm

Bottom bracket diameter 41 mm

Front derailleur type Direct Mount

Brakes mount type (maximum rotor size)

PM 160 mm

Seat post diameter 31.6 mm

Headset type Integrated tapered

Headset mount diameter 44 mm-55 mm

T4CRA010121 L

T4CRA010120 M

T4CRA010119 S

LEVEL R+Level R+ is the top of the line model of the 27.5” frames. Dedicated for the most demanding cyclists competing in marathons an cross-country races. The frame was created in collaboration with the leading Polish players of MTB scene - the Kross Racing Team. It was made of advanced carbon fiber Carbon SL, which thanks to the special layering ensure high rigidity at the same time very good damping characteristics while maintaining low weight. The wider seat post / bottom bracket junction strengthens the frame and makes it really fast. Short rear triangle and tapered headtube provides very good manoeuvrability on winding paths. Direct mount for front derailleur limits the amount of needed parts. This frame proved its quality on demanding European tracks.






PM 160 mm




T4CRA010130 L

T4CRA010129 M

T4CRA010128 S

CS

WBHA

ST

SA

TT

HT

BB DROP

REACH

STACK

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

CS

WBHA

ST

SA

TT

HT

BB DROP

REACH

STACK

17”

440

578

110

75

70

428

1077

406

605

57

S

19”

490

565

130

75

70

428

1094

416

624

57

M

21”

530

605

150

74

70

428

1105

420

643

57

L

17”

430

590

110

73

70

439

1084

403

611

62

S

19”

480

610

120

73

71

439

1094

419

624

62

M

21”

540

640

140

73

71.5

439

1118

442

646

62

L

ACCESSORIES • COMPONENTS

FRAMES

213

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

MOON Z3Moon Z3 is the highest model of a series of frames dedicated to enduro ride, based on 27.5” wheel. Guarantees high traction, allowing the fluid overcoming both technically difficult and fast section of the mountain trails. Is the best choice for those requiring not only the latest technical solutions, but above all, fun and an unforgettable experience while riding. Moon is an ideal basis for a bike that will satisfy the expectations of even the most demanding lovers of the mountains. Sure riding on narrow and winding paths provide braced construction elements such as tapered head and rear axle mount 142x12 mm standard. Precision when braking on steep descents will brake mounted on a Post Mount, which, with a view to the protection of the frame against damage is with interchangeable bushings. For smooth performance suspension system is responsible for Revo Suspension-independent Virtual drive action and, at the same time, reducing the effect of collapsing while pedaling. The efficiency of the power of the bicycle is also ensured thanks to the cams, which causes the bike has above-average side stiffness. To create a framework uses aluminum alloy Super Lite, so the construction is extremely durable while keeping a low weight. Aggressive nature of the framework was underlined by using the painting between matte coating and shine one. All the housings hide inside the frame, making it even more desirable among enduro enthusiasts.




Travel 160 mm



PM 180 mm




T4CRA016234 XL

T4CRA016233 L

T4CRA016232 M

T4CRA016231 S

VENTO 7.0Vento 7.0 is the highest model of a series of road frames. Made of carbon fiber ensures a very low weight, at the same time high stiffness. Uncompromising geometry provides exceptional characteristics of riding both on a steep driveway, and during dynamic spirit. BB in Press Fit standard allow for an easy way to mount bearings and at the same time, strengthen the framework and increase the efficiency while riding. Unidirectional carbon fibers absorb vibrations, so that the frame is also very comfortable. Tapered head to strengthen the front part of the frame, so the bike based on a Vento 7.0 frame quickly responds to decisions of the cyclist. Internal housing routing. Paired with lightweight fork and a headset dedicated to the frame.


Bottom bracket width 86.5 mm


Front derailleur type Plate Mount


Pivot Type




T4CRA016931 XL

T4CRA016930 L

T4CRA016929 M

T4CRA016928 S

CSWB

SA HA

ST

TT

HT

BB DROP

REACH

STACK

16”

410

565

100

74

65.5

440

1165

418

578

5.7

S

17”

440

585

110

74

65.5

440

1187

436

587

5.7

M

18”

470

605

120

74

65.5

440

1209

453

596

5.7

L

20”

500

625

135

74

65.5

440

1231

470

610

5.7

XL

19”

500

530

116

74

71.5

410

984

382

515

68

S

21”

530

540

141

74

72

410

990

385

540

68

M

22”

560

565

155.5

73.5

73.5

410

996

399

560

68

L

23”

590

575

186

73.5

73.5

410

1006

401

589

68

XL

CS

WBHA

ST

SA

TT

HT

BB DROP

REACH

STACK

FRAMES

214

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

LEVEL B10B10 frame is a great solution for people who want to try Marathon and cross country riding on 29’’ wheels. Light frame made of carbon fiber will help to build a bike that is agile on uphill and aggressive on the most demanding slopes.Tapered headtube to strengthen the front part of the structure. Bike based on the frame is responsive, even on the most winding single tracks. BB in Press Fit standard allow for an easy way to mount bearings and at the same time, strengthen the framework and increase the efficiency while riding. Internal housing routing. High quality construction and durable paint make R10 a great proposition for all fans of the true MTB riding.






PM 160 mm




T4CRA010282 L

T4CRA010281 M

T4CRA010280 S

LEVEL R10R10 frame is a great solution for people who want to try their best during Marathon and cross country races on 27.5” wheels. Light frame made of carbon fiber will help to build a bike and on uphill and aggressive on the most demanding slopes. Tapered headtube to strengthen the front part of the structure. Bike based on the frame is responsive, even on the most winding single tracks. BB in Press Fit standard allow for an easy way to mount bearings and at the same time, strengthen the framework and increase the efficiency while riding. Internal housing routing. High quality construction and durable paint make R10 a great proposition for all fans of the true MTB riding.






PM 160 mm




T4CRA016937 L

T4CRA016936 M

T4CRA016935 S

CS

WBHA

ST

SA

TT

HT

BB DROP

REACH

STACK

15”

382

593

100

73

72

435

1062

398

613

60

S

18”

452

606

120

73

72

435

1074

404

632

60

M

20”

487

628

125

73

72

435

1096

425

637

60

L

17”

432

590

105

74

70.5

430

1085

419

594

52

S

19”

483

614

120

74

71

430

1105

440

610

52

M

21”

532

638

135

73.5

71

430

1124

453

625

52

L

CS

WBHA

ST

SA

TT

HT

BB DROP

REACH

STACK


FRAMES

215

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

LEVEL B8Dedicated to the 29” wheel B8 frame is a well balanced compromise between weight and stiffness. Despite the fact that frame is dedicated to the larger wheels it is still great for narrow single tracks. Thanks to tapered the headtube quickly responds to decisions of the cyclist. BB in Press Fit standard allow for an easy way to mount bearings and at the same time, strengthen the framework and increase the efficiency while riding. Internal housing routing. Such a framework is an ideal equipment for people starting their adventure in the marathon and cross country competitions.






PM 160 mm




T4CRA016714 L

T4CRA016713 M

T4CRA016712 S

LEVEL R8Dedicated to the 27.5” wheel R8 frame is a well balanced compromise between weight and stiffness. Thanks to tapered the headtube quickly responds to decisions of the cyclist. BB in Press Fit standard allows for an easy way to mount bearings and at the same time, strengthen the framework and increase the efficiency while riding. Internal housing routing. Such a framework is an ideal equipment for people starting their adventure in the marathon and cross country competitions.






PM 160 mm




T4CRA016711 XL

T4CRA016710 L

T4CRA016709 M

T4CRA016708 S

CS

WBHA

ST

SA

TT

HT

BB DROP

REACH

STACK

17”

432

600

100

73.5

71.5

438

1094

426

624

63

S

19”

483

620

110

73.5

71.5

438

1116

443

633

63

M

21”

533

640

120

73.5

71.5

438

1131

460

643

63

L

23”

584

660

130

73.5

71.5

438

1150

477

652

63

XL

17”

432

594

115

73.5

71

425

1079

415

602

45

S

19”

483

613

125

73.5

71

425

1098

432

612

45

M

21”

534

632

135

73.5

71

425

1118

448

621

45

L

23”

585

651

145

73.5

71

425

1137

464

631

45

XL

CS

WBHA

ST

SA

TT

HT

BB DROP

REACH

STACK

FRAMES

216

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

VENTO 4.0Vento 4.0 is an ideal base to build a bike for people who appreciate quality at a reasonable price. Made of Aluminium UltraLite ensures good weight and high stiffness. A bicycle built based on Vento 4.0 will be fine climber but with an equally large confidence on the descent. Internal housing routing. Paired with lightweight fork and a headset dedicated to the frame.

Bottom bracket type BSA 1.37x24T


Seat tube diameter 31.8 mm

Front derailleur type Clamp Mount


Pivot Type


Headset type Integrated

Headset mount diameter 41.35 mm

T4CRA016909 XL

T4CRA016908 L

T4CRA016907 M

T4CRA016906 S

LEVEL B4The Level B4 frame is a great option for starting your adventure with mountain biking and 29’’ wheels. The robust frame made of Aluminium Lite ensures excellent riding experience also in the more demanding terrain. Smooth welds underline the sporty character of the frame. The painting was made in the Powder Coating technology which ensures long durability and freshness of the paint.






IS 160 mm



Headset mount diameter 44 mm

T4CRA016643 XL

T4CRA016642 L

T4CRA016641 M

T4CRA016640 S

CS

WBHA

ST

SA

TT

HT

BB DROP

REACH

STACK

17”

432

590

110

74.3

70.5

443

1084

395

637

63

S

19”

483

610

120

74.3

70.5

443

1105

412

646

63

M

21”

534

630

130

74.3

70.5

443

1125

429

655

63

L

23”

584

650

140

74.3

70.5

443

1145

446

665

63

XL

19”

500

540

155

74

72

415

987

379

562

75

S

21”

530

558

175

73.5

72.5

415

996

385

582

75

M

22”

560

577

195

73

73

415

1003

392

604

75

L

23”

590

595

205

73

73.5

415

1017

407

615

75

XL

CS

WBHA

ST

SA

TT

HT

BB DROP

REACH

STACK


FRAMES

217

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

FS FRAME SIZE

ST SEAT TUBE LENGHT

TT TOP TUBE LENGHT

HT HEAD TUBE LENGHT

SA SEAT TUBE ANGLE

HA HEAD TUBE ANGLE

CS CHAINSTAY LENGHT

WB WHEEL BASE

REACH

STACK

BB DROP

LEVEL R4The Level R4 frame is a great option for starting your adventure with mountain biking and 27.5” wheels. The robust frame made of Aluminium Lite ensures excellent riding experience also in the more demanding terrain. Smooth welds underline the sporty character of the frame. The painting was made in the Powder Coating technology which ensures long durability and freshness of the paint.






IS 160 mm




T4CRA009876 XL

T4CRA009875 L

T4CRA009874 M

T4CRA009873 S

LEA R4Lea R4 frame is a great proposition for women starting their adventure with mountain biking and wheels 27.5’’. Specially designed for women this frame has been made of Aluminium Performance. Guarantees very good riding experience also in the more demanding terrain. Application of hydroformed tubes has significantly reduced the weight of the frame. It’s hard to go past not noticing specially designed graphics that meet even the most demanding feminine tastes.






IS 160 mm




T4CRA016438 M

T4CRA016437 S

T4CRA016436 XS

CS

WBHA

ST

SA

TT

HT

BB DROP

REACH

STACK

CS

WBHA

ST

SA

TT

HT

BB DROP

REACH

STACK

15”

381

545

125

72.5

70

430

1030

374

609

35

XS

17”

432

560

135

72.5

70

430

1046

375

618.5

35

S

19”

483

575

145

72.5

70

430

1060

382

628

35

M

17”

432

585

120

73

70.5

430

1073

400

605

45

S

19”

483

603

130

73

70.5

430

1092

415

615

45

M

21”

534

620

140

73

70.5

430

1109

430

624

45

L

23”

584

638

150

73

70.5

430

1128

444

633

45

XL

DROPOUTS

218

DROPOUT PICTURE YEAR MODELS PRODUCT CODE

DP-1 2014 LEA F1, TRANS PACIFIC T4CIN001056

DP-2

2014 ESPRIT 610, ESPRIT 910, EVADO 1.0, EVADO 2.0, LEA B2, LEA B3, LEVEL REPLICA, MOVE

T4CIN001057

2015 EVADO 1, EVADO 2, EVADO 3, LEVEL REPLICA

DP-3

2014 BISETTE, MODO 1.0, MODO 2.0, SATINE, SILK, TRESSE, VENTO 1.0, VENTO 2.0

T4CIN0010722015 SILK, SATINE, TRESSE, BISETTE, PULSO 1, PULSO 2, VENTO 1.0,

VENTO 2.0, VENTO 3.0, VENTO 4.0

DP-4

2014 BERG, BLACK L1, ESENSO, FLEX 2.0, HEXAGON X1, TRANS ALP, TRANS ATLANTIC, TRANS SIBERIAN, TRANS ARCTICA

T4CIN001197

2015ESENSO, FLEX 2.0, HEXAGON X1, HEXAGON X2, TRANS ALP, TRANS ARCTICA, TRANS ATLANTIS, TRANS INDIA, TRANS PACIFIC, TRANS SIBERIAN

DP-5

2014BLACKEDITION1, DIGGER, HEXAGONX1, HEXAGONX2DISC, HEXAGONX3, HEXAGONX4, HEXAGONX5, HEXAGONX6, HEXAGONX7, HEXAGONX8, HEXAGONX9, LEA F2, LEA F3, LEA F4

T4CIN001198

2015

LEA F1, LEA F2, LEA F3, LEA F4, LEA R2, LEA R4, LEA R6, HEXAGON R3, HEXAGON R4, HEXAGON R5, HEXAGON R6, HEXAGON R8, HEXAGON X2 DISC, HEXAGON X3, HEXAGON X4, HEXAGON X5, HEXAGON X6, LEVEL A2, LEVEL A3, LEVEL A4, LEVEL A6, LEVEL B2, LEVEL B3, LEVEL B4, LEVEL R2, LEVEL R3, LEVEL R4, LEVEL R6, DIGGER, TRANS AFRICA, TRANS GLOBAL, TRANS SOLAR, SETO, INZAI

DP-6

2014 LEVEL A7, LEVEL A8, LEVEL B6, LEVEL B7, LEVEL R8

T4CIN001371

2015 LEVEL B6, LEVEL B7, LEVEL B8, LEVEL R7, LEVEL R8

DP-7 2014 EVADO 3.0, EVADO 4.0, EVADO 5.0 T4CIN001385

DP-8

2014 SPADE REPLICA

T4CIN001390

2015 SPADE REPLICA

DP-9

2014 LEVEL B9, LEVEL B10

T4CIN001413

2015 LEVEL R9, LEVEL R10, LEVEL B9, LEVEL B10

DP-10

2014 VENTO 3.0, VENTO 4.0

T4CIN001414

2015 VENTO 5.0, VENTO 6.0, VENTO 7.0

DP-11

2014 EVADO 7.0

T4CIN001440

2015 EVADO 4.0, EVADO 5.0, EVADO 6.0, EVADO 7.0


DROPOUTS

219

DROPOUT PICTURE YEAR MODELS PRODUCT CODE

DP-12 2014 EARTH T4CIN001476

DP-13

2014 MOON

T4CIN001477

2015 MOON V, MOON Z

DP-14

2014 LEVEL A11, LEVEL A+, LEVEL R9, LEVEL R10, LEVEL R+

T4CIN001537

2015 LEVEL R11, LEVEL R12, LEVEL R+

DP-15

2014 B11 , B+

T4CIN001538

2015 LEVEL B11, LEVEL B12, LEVEL B+

DP-16 2014 LEVEL A9 , LEVEL A10 T4CIN001539

DP-17 2010 CRIME T4CIN001041

DP-18

LEVEL A4, LEVEL A6, LEVEL A8

T4CIN001042

2011 LEVEL A4, LEVEL A6, LEVEL A7, LEVEL A9

DP-19 2010 LEVEL A10 T4CIN001043

DP-21

2012 LEVEL A+

T4CIN000001

2013 LEVEL A+, LEVEL A11

DP-22

2012 LEVEL A9, LEVEL A10

T4CIN000002

2013 LEVEL A9 , LEVEL A10

DP-23

2012 EARTH

T4CIN000003

2013 EARTH

DP-24 2014

BIG BLACK 2, BLACK EDITION 2, BLACK EDITION 3, ESPRIT 720, INZAI, LEA F5, LEA F6, LEA F7, LEA F8, LEVEL A2, LEVEL A3, LEVEL A4, LEVEL A5, LEVEL A6, LEVEL B2, LEVEL B3, LEVEL B4, LEVEL R2, LEVEL R3, LEVEL R4, LEVEL R6, SETO, TRANS GLOBAL, TRANS SOLAR

T4CIN001425

CHAINS

220

SLA DHA ROLLER DHA PIN HP BL IC OC NS SR QRs LINK PIN QF SINGLE PIN

• • • • • • • • • •

• • • • • • • • • •

• • • • • • • •

• • • • • •

• • • • • •

• • • • • •

• • • • • •

• • • • •

• • • • • • •

• • • • •

• • • • •

• •

NAME IMAGE SPEED WEIGHT WIDTH LINKS CODE

SLA11 11 257g 5.6 mm 116L T4CLA000177

SLA10 11 267g 5.9 mm 116L T4CLA000176

S10 10 253g 5.9 mm 116L T4CLA000175

SH10 10 286g 5.9 mm 116L T4CLA000174

S9 9 291g 6.4 mm 116L T4CLA000173

SH9S 9 299g 6.4 mm 116L T4CLA000172

SH9G 9 299g 6.4 mm 116L T4CLA000171

S8S 8 300g 7.3 mm 116L T4CLA000170

S8G 8 300g 7.3 mm 116L T4CLA000169

S7/8 7/8 318g 7.3 mm 116L T4CLA000168

S6 6/7 322g 7.3 mm 116L T4CLA000167

Single 1 322g 8.6 mm 116L T4CLA000166

NAME IMAGE SPEED WEIGHT WIDTH CODE

QRs 7-8 7/8 25g 7.5 mm T4CLA000073

QRs 9 9 25g 6.4 mm T4CLA000074

QRs 10 10 25g 5.9 mm T4CLA000075


CHAINS

221

SLA DHA ROLLER DHA PIN HP BL IC OC NS SR QRs LINK PIN QF SINGLE PIN

• • • • • • • • • •

• • • • • • • • • •

• • • • • • • •

• • • • • •

• • • • • •

• • • • • •

• • • • • •

• • • • •

• • • • • • •

• • • • •

• • • • •

• •

SLA Superior Lubricant Aid is a special Ni-PTFE coating on chain plate for less friction and increasing 100% chain life

DHA ROLLER A Chromium Hardened Roller coated by a special chromium carbide layer

DHA PIN A Chromium Hardened Pin coated by a special chromium carbide layer

HP Solid tube, 20% lighter than traditional pin with no loss of strength

BL Technology aids in smooth shift transmission without binding

IC On the inner plate and outer plate is for anti drop of chain caused in back pedaling situation

OC The chamfering is on the end of the outer plate and reduce 80% and above shifting

NS Insure the quitest chain even while shifting up or down

SR Effect high pin power

QRS LINK Durabel Quick Release link included

PIN QF Quick Fasten pin included providing easy chain mounting

SINGLE PIN On the outer plate included pin to easy chain mounting

NAME IMAGE SPEED WEIGHT WIDTH LINKS CODE

SLA11 11 257g 5.6 mm 116L T4CLA000177

SLA10 11 267g 5.9 mm 116L T4CLA000176

S10 10 253g 5.9 mm 116L T4CLA000175

SH10 10 286g 5.9 mm 116L T4CLA000174

S9 9 291g 6.4 mm 116L T4CLA000173

SH9S 9 299g 6.4 mm 116L T4CLA000172

SH9G 9 299g 6.4 mm 116L T4CLA000171

S8S 8 300g 7.3 mm 116L T4CLA000170

S8G 8 300g 7.3 mm 116L T4CLA000169

S7/8 7/8 318g 7.3 mm 116L T4CLA000168

S6 6/7 322g 7.3 mm 116L T4CLA000167

Single 1 322g 8.6 mm 116L T4CLA000166

NAME IMAGE SPEED WEIGHT WIDTH CODE

QRs 7-8 7/8 25g 7.5 mm T4CLA000073

QRs 9 9 25g 6.4 mm T4CLA000074

QRs 10 10 25g 5.9 mm T4CLA000075

BRAKE PADS

222

VB-1Light brake pads provide stopping power in a variety of weather conditions. Exchangeable cartridges.

Braking surface 3-function, 72 mm long

Brake shoes cartridge, exchangeable

Color black-orange-grey.

T4CKL000069

VB-2Light brake pads provide stopping power in a variety of weather conditions. Exchangeable cartridges.

Braking surface 1-function, 72 mm long

Brake shoes cartridge, exchangeable

Color black-grey-red.

T4CKL000068

VB-3Classic brake pads V-brake type, to ensure proper operation during braking. Brake surface in three colors.

Braking surface classic, 72 mm long

Brake shoes non-exchangeable

Color black-grey-red

T4CKL000067

VB-4Classic brake pads V-brake type, to ensure proper operation during braking. Brake surface made in black.

Braking surface classic, 70 mm long

Brake shoes non-exchangeable

Color black.

T4CKL000066


CABLES & HOUSINGS

223

CABLE GEARHigh quality shifter cable made from steel wires.

Size 1.2 mm x 1800 mm.

Color silver

T4CLN000404

BRAKE CABLEHigh quality brake cable made from steel wires.

Size 1.5 mm x 1800 mm.

Color silver

T4CLN000403

UNIVERSAL CABLE HOUSINGS 2PHousing reinforced with braided steel tape. The possibility of using it for the brake and derailleur. The inner polyethylene liner minimizes friction. Recommended use of aluminum ferrules.

T4CPN000134 BLACK

T4CPN000135 WHITE

T4CPN000129 RED

T4CPN000128 BLUE

PEDALS

224

DURABLERacing MTB pedals compatible with SPD system. Ability to adjust the clip out tension. Sealed bearings will provide durability in difficult weather conditions. Set with cleats.

Use MTB

Material - body - cold forged aluminium - axle - CNC machined Cr-Mo steel

Bearing system LSL/sealed

Clip system double sided, SPD compatible, adjustable 80~140 kgf. cm

Extras cleats included

Platform dimensions 79 x 66 mm

Weight 320 g / pair

T4CPE000225

STUNTRacing MTB pedals compatible with SPD system. Ability to adjust the clip out tension. Sealed bearings will provide durability in difficult weather conditions. Set with cleats.

Use MTB

Material - body - polished aluminium - axle - Cr-Mo steel CNC machined





Weight 320 g / pair

T4CPE000219

COUPRacing MTB pedals compatible with SPD system. Ability to adjust the clip out tension. Sealed bearings will provide durability in difficult weather conditions. Set with cleats.

Use MTB

Material - body - polished aluminium - axle - Cr-Mo steel CNC machined

Bearing system ball



Platform dimensions 80 x 55 mm.

Weight 320 g / pair

T4CPE000218

TAILOREDRoad pedals compatible with SPD system. Ability to adjust the clip out tension. Sealed bearings system will provide a durable work in difficult weather conditions. Complete with cleats.

Use Road - body - hand polished aluminium - axle - CNC machined Cr-Mo steel

Material - body - hand polished aluminium - axle - CNC machined Cr-Mo steel





Weight 292 g / pair

T4CPE000224

PEDALS

ACCESSORIES • COMPONENTS225

LOOPRacing road pedals compatible with Look system. Ability to adjust the clip out tension. Sealed bearings will provide durability in difficult weather conditions. Set with cleats.

Use Road

Material - body - aluminium - axle - Cr-Mo steel CNC machined


Clip system single sided, Look compatible, adjustable 80~140 kgf. cm



Weight 280 g / pair

T4CPE000220

HURRIEDRoad bike pedals compatible with Look system. Ability to adjust the strength of clip out tension. Complete with cleats.

Use Road

Material - body - reinforced plastic composite - axle - boron steel

Bearing system ball

Clip system single sided, Look compatible, adjustable 80~140 kgf. cm



Weight 232 g / pair

T4CPE000223

PYLON-ADVRugged pedals with an aluminium body, dedicated to trekking and MTB bikes. With a one-sided system compatible with SPD, therefore are also comfortable to ride in the traditional shoes. Set with cleats.

Use Trekking / MTB

Material - body - aluminium - axle - Cr-Mo steel

Bearing system ball

Clip system single sided, SPD compatible, adjustable 80~140 kgf. cm

Extras side reflector, cleats included


Weight 446 g / pair

T4CPE000217

PYLONRugged pedals with an aluminium body, dedicated to trekking and urban bikes. With a one-sided system compatible with SPD, therefore also comfortable to ride in the traditional shoes. Set with cleats.

Use MTB

Material - body - aluminium - axle - Cr-Mo steel

Bearing system ball

Clip system single sided, SPD compatible, adjustable 80~140 kgf. cm



Weight 446 g / pair

T4CPE000183

PEDALS

226

PILLARRugged pedals with an aluminium body. Dedicated to MTB bikes. Thanks to the appropriately designed the platform provide a good grip for the shoe.

Use Trekking / Urban / City

Material - body - polished aluminium - cage - aluminium - axle - Cr-Mo steel

Bearing system ball

Extras side reflector


Weight 250 g / pair

T4CPE000216

SINEW-ADVRugged pedals with an aluminium body. Dedicated to trekking bikes. Thanks to the appropriately design and anti-slip cover platform provide a good grip for the shoe.

Use City / Trekking

Material - body - polished aluminium - cage - plastic composite with anti slip coating - axle - Cr-Mo steel

Bearing system ball



Weight 310 g / pair

T4CPE000203

SINEWDedicated to trekking and urban bikes, made of plastic composite and steel axles. Provide a good grip for shoe. Built-in reflectors enhance visibility on the road.

Use Trekking / Urban / City

Material - body - plastic composite - axle - steel

Bearing system ball



Weight 230 g / pair

T4CPE000214

BEDROCKDedicated to trekking and urban bikes, made of plastic composite and steel axles. Provide a good grip for shoe. Built-in reflectors enhance visibility on the road.

Use Trekking / City / Cross


Bearing system ball



Weight 238 g / pair

T4CPE000213

PEDALS


RADIXChild pedals, made of plastic composite and steel axles. Provide a good grip for shoe. Built-in reflectors enhance visibility on the road.

Use Junior


Bearing system ball



Weight 220 g / pair

T4CPE000212

SPD CLEATSMTB cleats made of Cr-Mo steel, to ensure trouble-free operation. Provide convenient, multi-directional clip out. Compatible with SPD system.

System SPD

Weight 56 g

T4CPE000221

LOOK CLEATSRoad cleats made of plastic composite. Ensure trouble-free operation. Provide convenient, multi directional clip out. Compatible with Look system.

System Look

Weight 75 g

T4CPE000222

HANDLEBARS

228

A2RBHDurable handlebar designed for MTB. The use of butted 7075-T6 aluminum ensures low weight parameters and high stiffness. Carbon fiber coating provides damping and ensures riding comfort.

Material double butted AL7075-T6 aluminium with carbon fiber coating

Upsweep 7°

Back sweep 8°

Rise 20 mm

Diameter 31.8 mm

Width 620 mm

Weight 214 g

T4CKI000284

A2XBHA simple, durable handlebar designed for MTB use. The use of butted 7075-T6 aluminum ensures low weight parameters and high stiffness. Carbon fiber coating provides damping and ensures riding comfort.

Material double butted AL7075-T6 aluminium w. carbon fiber coating

Back sweep 6°

Diameter 31.8 mm

Width 600 mm

Weight 169 g

T4CKI000283

B3RBHDurable, bent handlebar designed for MTB use. The use of butted 7075-T6 aluminum ensures low weight parameters and high stiffness.

Material double butted AL7075-T6 aluminium

Upsweep 5°

Back sweep 8°

Rise 50 mm

Diameter 31.8 mm

Width 710 mm

Weight 338 g

T4CKI000282

A3RBHDurable, bent handlebar designed for MTB use. The use of butted 7075-T6 aluminum ensures low weight parameters and high stiffness.


Upsweep 6°

Back sweep 5°

Rise 20 mm

Diameter 31.8 mm

Width 66 mm

Weight 231 g

T4CKI000281


HANDLEBARS

229

A3XBHA simple, durable handlebar designed for MTB use. The use of butted 7075-T6 aluminum ensures low weight parameters and high stiffness.


Back sweep 6°

Diameter 31.8 mm

Width 600 mm

Weight 187 g

T4CKI000280

B3RBHDurable, bent handlebar designed for MTB use. The use of butted 6061-T6 aluminum ensures low weight parameters and high stiffness.


Upsweep 5°

Back sweep 8°

Rise 50 mm

Diameter 31.8 mm

Width 710 mm

Weight 380 g

T4CKI000279

A3RBHDurable, bent handlebar designed for MTB use. The use of butted 6061-T6 aluminum ensures low weight parameters and high stiffness.


Upsweep 6°

Back sweep 5°

Rise 20 mm

Diameter 31.8 mm

Width 66 mm

Weight 298 g

T4CKI000278

A3XBHA simple, durable handlebar designed for MTB use. The use of butted 7075-T6 aluminum ensures low weight parameters and high stiffness.


Back sweep 6°

Diameter 31.8 mm

Width 600 mm

Weight 187 g

T4CKI000277

HANDLEBARS

230

MTB01AA simple handlebar made of 6061 aluminium. Double butting for low weight and high rigidity.


Back sweep 5°

Rise 60 mm

Diameter 31.8 mm

Width 600, 620 mm

Weight 257 g (600mm)

T4CKI000285 600 MM

T4CKI000286 620 MM

MTB11AFFlat handlebar made of 6061 aluminium. Double butting for low weight and high rigidity.


Back sweep 8°

Rise 70 mm

Diameter 31.8 mm

Width 680, 700 mm

Weight 250 g (680 mm)

T4CKI000288 680 MM

T4CKI000287 700 MM

MTB442ALow rise handlebar made of 6061 aluminium. Double butted for low weight and high rigidity.


Upsweep 5°

Back sweep 8°

Rise 90 mm

Diameter 31.8 mm

Width 660 mm

Weight 294 g

T4CKI000289


STEMS

231

A2MBSLight stem made of aluminum covered with carbon coating. Low weight and very good strength parameters for the most demanding riders. Allows you to set the position with a negative or positive angle.

Type ahead

Material double butted AL 2014 aluminium w. carbon fiber coating

Fork Diameter 28.6 mm

Handlebar Diameter 31.8 mm

Angle + / - 5°

Length 90, 110 mm


T4CWS000862 90 MM

T4CWS000863 110 MM

CR5.3SLightweight handlebar made of aluminium alloy to ensure high strength and stiffness. Provide great control over your bike during both climbing and intense downhill. Allows you to set the position with a negative or positive angle.

Type ahead

Material 3D cold forged 7075-T6 aluminium



Angle + / - 5°

Length 90, 110, 120 mm


T4CWS000857 110 MM

T4CWS000858 120 MM

T4CWS000856 90 MM

CR3.3SLightweight handlebar made of aluminium alloy to ensure high strength and stiffness. Provide great control over your bike during both climbing and intense downhill. Allows you to set the position with a negative or positive angle.

Type ahead

Material cold forged aluminium AL6061



Angle + / - 5°

Length 90 mm

Weight 149 g

T4CWS000859 90 MM

T4CWS000860 110 MM

T4CWS000861 120 MM

JD-ST57AHandlebar made cold-forged aluminum. Good stiffness provide great control over the bike. Allows you to set the position with a negative or positive angle.

Type ahead




Angle + / - 6°

Length 75, 90, 100, 110 mm


T4CWS000872 75 MM

T4CWS000873 90 MM

T4CWS000874 100 MM

T4CWS000875 110 MM

STEMS

232

JD-ST57AHandlebar made cold-forged aluminum. Good stiffness provide great control over the bike. Allows you to set the position with a negative or positive angle.

Type ahead




Angle + / - 6°

Length 75, 90, 100, 110 mm


T4CWS000872 75 MM

T4CWS000873 90 MM

T4CWS000874 100 MM

T4CWS000875 110 MM

AL-812Sturdy, quill type stem made of forged aluminium. Adjustable angle for comfort and firm lock for good control while riding.

Type quill, adjustable

Material cold forged aluminium



Angle 0°-60°

Length 110 mm

Weight 520 g

T4CWS001245

AS-828Stem made of forged aluminium. Good stiffness provide good control over the bike. Adjustability allows you to easily set the angle and height of the handlebar.

Type ahead, adjustable

Material forged aluminium



Angle 0°-60°

Length 115 mm

Weight 240 g

T4CWS001241BK BLACK


BARENDS

233

ERGOLIGHTErgonomic bar ends made of one piece 3D forged light aluminum alloy 6061-T6, which guarantees high durability and rigidity. Great fit for the palm of your hand, improve ride comfort.

Material one piece 3D forged 6061-T6 aluminium

Length 90 mm

Weight 110 g (pair)

T4CRO000058BK BLACK

T4CRO000058WH WHITE

BALANCEErgonomic bar ends made of light aluminum alloy 6061-T6 , which guarantees high durability and rigidity. Great fit for the palm of your hand, improve ride comfort.

Material forged 6061-T6 aluminium

Length 80 mm

Weight 100 g (pair)

T4CRO000059BK BLACK

GRIPS

234

IGUANAGrips made of special hardened foam. Allows you to use them without gloves. Aluminium o-rings allow for to secure mounting on the handlebar. Set with bar plugs.

Material hi density foam

Length 128 mm

Weight 100 g (pair)

T4CCH000263

LIZARDGrips made of durable and comfortable mix of rubber . Aluminium o-rings allow secure mounting on the handlebar. Set with bar plugs.

Material rubber compound

Length 128 mm

Weight 104 g (pair)

T4CCH000262BK BLACK

T4CCH000262RD RED

T4CCH000262WH WHITE

GECKONGrips made of durable and comfortable mix of rubber. Aluminium o-rings allow secure mounting on the handlebar. Set with bar plugs.

Material rubber compound

Length 130 mm

Weight 110 g (pair)

T4CCH000264

GRIPENComfortable grips made from a mixture of two types of rubber. Thanks to this treatment grips are comfortable and durable. Grip shape improves ergonomics and reduces the fatigue caused by the handlebar.

Material dual density rubber compound

Length 130 mm

Weight 145 g (pair)

T4CCH000261

SCALEGrips made of durable and comfortable mix of rubber. Dual density rubber for vibrations absorbing and excellent grip.

Material dual density rubber compoud

Length 130 mm

Weight 120 g (pair)

T4CCH000268RD RED

T4CCH000268BL BLUE

T4CCH000268GY GRAPHITE

T4CCH000268WH WHITE


GRIPS

235

FLANNELBar tape made from EVA foam. Absorbs vibrations on the handlebar. With its high tensile strength it can be wrapped very accurately on the handlebar. Set with bar plugs.

Material EVA

Length 2 x 185 cm

Weight 55 g

T4CCH000266

STRANGLERBar tape made out of foam and polyurethane. Perectly absorbs vibrations of the handlebar. With its high tensile strength you can wrap it accurately on the handlebar. Set with bar plugs.

Material SBR foam

Length 2 x 185 cm

Weight 87 g

T4CCH000267

RAINBOWSafe and comfortable grips designed for children’s bikes. Soft rubber and high flanges increase comfort and safety.

Material Kraton

Length 102 mm

Weight 85 g (pair)

T4CCH000259BK BLACK

T4CCH000259BL BLUE

T4CCH000259GRB GREEN

T4CCH000259PI PINK

SCUTErgonomically contoured grips - comfortable and durable at the same time. Grip shape improves ergonomics and reduces inconvenience caused by the handlebar.

Material dual density rubber compound

Length 130 mm

Weight 135 g (pair)

T4CCH000265

SEATPOSTS

236

A2MBPSeatpost made of high quality aluminum alloy carbon coating. Thanks to the technology used, seatpost will absorb vibration, improving ride comfort.

Material AL 2014 aluminium with carbon fiber coating

Size 27.2 x 350 mm

Offset 10 mm

Weight 223 g

T4CWS000865

A3MBPLightweight seatpost made from high-quality aluminum alloy, CNC machined. Through the use of 3D technology while forging, it has good mechanical parameters and low weight.

Material 3D cold forged CNC machined AL 2014 aluminium

Size 27.2 x 400 mm

Offset 10 mm

Weight 263 g

T4CWS000864

C3MBPSeatpost made from 3D forged, high-quality aluminium alloy 6061-T6, ensure good weight parameters.

Material 3D cold forged AL 2014 aluminium

Size 27.2; 28.6; 30.8; 31.6 mm

Length 400 mm

Offset 10 mm

Weight 321 g (27.2 mm)

T4CWS000866 27.2 MM

T4CWS000867 28.6 MM

T4CWS000868 30.8 MM

T4CWS000869 31.6 MM

JD-SP65TSeatpost made from high-quality aluminium alloy ensure good weight parameters.

Material AL 6061 aluminium

Size 27.2; 31.6 mm

Length 350 mm

Offset 10 mm


T4CWS000876 27.2 MM

T4CWS000877 31.6 MM

SP-602Basic seatpost made of aluminium.

Material aluminium

Size 27.2; 31.6 mm

Length 350 mm


T4CWS001217 27.2 MM

T4CWS001218 31.6 MM

SADDLES


FEATComfortable saddle made of high-density foam. Synthetic leather joined seamlessly to provide comfort also on long routes. Padding made of two layers for a better distribution of weight. Cut-out located in the central part of the saddle reduces pressure on the delicate spots, thus ensures that the saddle does not have negative influence on the proper blood circulation.

Coating synthetic leather

Fill high density foam

Rails Ø 7 mm hardened steel

Category race

Dimensions 268x133 mm

Weight 295 g

T4CSI000844RD RED

T4CSI000844GY GREY

DEEDComfortable saddle made of high-density foam that matches perfectly to the body anatomy. Synthetic leather joined seamlessly to provide comfort also on long routes. Padding made of two layers for a better distribution of weight.




Category sport


Weight 294 g

T4CSI000845RDWH RED-WHITE

T4CSI000845BLGY BLUE-GREY

T4CSI000845RDGY RED-GREY

STUNTComfortable saddle made of high-density foam. Synthetic leather joined seamlessly to provide comfort also on long routes. Padding made of two layers for a better distribution of weight and absorption of the shocks caused by the terrain. Cut-out located in the central part of the saddle reduces pressure on the delicate spots, thus ensures that the saddle does not have negative influence on the proper blood circulation. Polished surface layer allows for convenient cleaning from any dirt.




Category sport


Weight 313 g

T4CSI000846RD RED

T4CSI000846GR GREEN

T4CSI000846YL YELLOW

SNAPPYComfortable saddle made of high-density foam. Synthetic leather joined seamlessly to provide comfort also on long routes. Padding made of two layers for a better distribution of weight and absorption of the shocks caused by the terrain. Cut-out located in the central part of the saddle decrease the weight, reduces pressure on the delicate spots, thus ensures that the saddle does not have negative influence on the proper blood circulation.




Category Active


Weight 314 g

T4CSI000847GR GREEN

T4CSI000847OR ORANGE

SADDLES

238

VIVIDComfortable saddle made of high-density foam. Synthetic leather joined seamlessly to provide comfort also on long routes. Padding made of two layers for a better distribution of weight and absorption of the shocks caused by the terrain. Protective flange made of abrasion-resistant material at the bottom of the saddle ensures durability and protects against abrasion. Cut-out located in the central part of the saddle decrease the weight, reduces pressure on the delicate spots, thus ensures that the saddle does not have negative influence on the proper blood circulation.




Category Active


Weight 354 g

T4CSI000848PI PINK

T4CSI000848BL BLUE

VIGORComfortable saddle made of high-density foam. Synthetic leather joined seamlessly to provide comfort also on long routes. Padding made of two layers for a better distribution of weight. Cut-out located in the central part of the saddle reduces pressure on the delicate spots, thus ensures that the saddle does not have negative influence on the proper blood circulation.




Category Active


Weight 315 g

T4CSI000849RD RED

T4CSI000849BL BLUE

COMFYComfortable saddle, dedicated to urban bike, made of high-density foam. Synthetic leather for comfort also on long routes. Built-in elastomers effectively suppress vibrations from the obstacles. Padding made of two foam layers for a better distribution of weight.




Additional information vibration damping elastomer inserts

Category City


Weight 600 g

T4CSI000850BR BROWN

T4CSI000850GPBE GRAPHITE-BEIGE

SADDLES


PROUD MANComfortable saddle, dedicated to urban bikes, made of high-density foam. Synthetic leather for comfort also on long city routes. Built-in elastomers effectively suppress vibrations from the obstacles. Padding made of two layers for a better distribution of weight. With side shields to prevent damage that may be caused by leaning bike against walls, etc.





Category City


Weight 569 g

T4CSI000855BK BLACK

PROUD LADYComfortable saddle, dedicated to urban bikes, made of high-density foam. Synthetic leather for comfort also on long city routes. Built-in elastomers effectively suppress vibrations from the obstacles. Padding made of two layers for a better distribution of weight. With side shields to prevent damage that may be caused by leaning bike against walls, etc.





Category City


Weight 633 g

T4CSI000856BK BLACK

SPRINGYComfortable saddle, dedicated to urban bike, made of high-density foam. Synthetic leather for comfort also on long routes. Padding made of two layers for a better distribution of weight. Polished surface layer allows for convenient cleaning from any dirt.




Category City


Weight 564 g

T4CSI000851BR BROWN

T4CSI000851BK BLACK

NATTYComfortable saddle made of high-density foam. Synthetic leather joined seamlessly to provide comfort also on long routes. Padding made of two layers for a better distribution of weight.Cut-out located in the central part of the saddle reduces pressure on the delicate spots, thus ensures that the saddle does not have negative influence on the proper blood circulation. With side shields to prevent damage.




Category Junior


Weight 360 g

T4CSI000852RD RED

T4CSI000852PI PINK

SADDLES

240

CUTE KIDComfortable saddle, dedicated to children’s bicycles, made of high-density foam. Synthetic leather joined seamlessly, provide high level of comfort.




Category Kid


Weight 292 g

T4CSI000853PI PINK

T4CSI000853BLB BLUE

TIKEComfortable saddle, dedicated to children’s bicycle, made of high-density foam. Synthetic leather joined seamlessly, providing high level of comfort.




Category Kid


Weight 279 g

T4CSI000854BLOR BLUE-ORANGE

T4CSI000854GRGY GREEN-GREY

SADDLES


NAMELENGTH

[mm]WIDTH[mm]

WEIGHT[g] CHARACTERISTICS CODE

Feat 268 133 295 • • • • T4CSI000844

Deed 275 138 293.5 • • • T4CSI000845

Stunt 278 145 313 • • • • • T4CSI000846

Snappy 276 143 314 • • • • T4CSI000847

Vivid 270 155 363.5 • • • • T4CSI000848

Vigor 275 135 315 • • • T4CSI000849

Comfy 258 185 600 • • • T4CSI000850

Springy 246 180 384 • • • • T4CSI000851

Proud Man 260 178 569 • • • • T4CSI000855

Proud Lady 238 205 633 • • • • • T4CSI000856

Cute Kid 207 150 291.5 • • T4CSI000853

Tike 217 142 278.5 • • T4CSI000854

Natty 245 145 360 • • • • T4CSI000852

SOFT

FO

AM

AN

ATO

MIC

CEN

TER

G

RO

OVE

ULT

RA

LIG

HT

PAD

DIN

G

FLEX

IBLE

PR

ESSU

RE

REL

IEF

BA

SE Z

ON

E

AD

AP

TIVE

FLE

X D

ESIG

N

PR

ESSU

RE

REL

IEF

BU

MP

ER

PR

OTE

CTI

VE

BU

MP

ER G

UA

RD

FULL

TR

IM

FULL

CU

T

PO

LISH

ED B

ASE

SOFT FOAM Specialty formulated PU foam made to improve the softness of the saddle, but still remain firm to the road.

ANATOMIC CENTER GROOVE Groove down the center is designed specifically to the contour of the saddle to improve comfort and performance.

ULTRA LIGHT PADDING Additional padding with little added weight.

FLEXIBLE PRESSURE RELIEF BASE ZONE Helps to reduce pressure on the rider. Base is designed to relive the pressure created by the terrain.

ADAPTIVE FLEX DESIGN The flexibility of a saddle is able to respond to potential internal or external changes improving comfort and performance.

PRESSURE RELIEF BUMPER Bumpers are mounted to allow pressure to relive from the base and still maintain a firm shape of foam.

PROTECTIVE BUMPER GUARD Bumpers mounted to protect saddle from damage.

FULL TRIM Trim surrounds the underneath of the saddle to enhance the style and secure the cover from rip or tear.

FULL CUT Center cut hole allows air to flow through, which can improve comfort and performance of the saddle.

POLISHED BASE Base is polished to unique finish to maintain shine and sleek look. Also, allows for easy clean-up from the dirty terrain.

WHEELS

242

SIZE VERSION HOLE COUNT MATERIAL PROFILE BRAKE FINISH COLOR AXLE MOUNT FREEWHEEL DISC MOUNT EXTRAS CODE

20” front 28 aluminium single wall V-Brake standard silver 10 mm (3/8”) nuts and washers - - - T4CKO200044SI

20” rear 28 steel single wall V-Brake standard silver 10 mm (3/8”) nuts and washers torpedo - cog, lock washer T4CKO200045SI

20” rear 28 aluminium single wall V-Brake standard silver 10 mm (3/8”) nuts and washers thread-on - - T4CKO200046SI

24” front 32 aluminium high profile V-Brake CNC machined black 10 mm (3/8”) nuts and washers - - - T4CKO240044BK

24” rear 32 aluminium high profile V-Brake CNC machined black 10 mm (3/8”) nuts and washers thread-on - - T4CKO240045BK

24” front 32 aluminium high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers - - - T4CKO240046SI

24” rear 32 steel high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers torpedo - cog, lock washer T4CKO240047SI




26” rear 32 aluminium high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers thread-on - - T4CKO260052SI


26” front 32 aluminium high profile V-Brake CNC machined black 10 mm (3/8”) QR - - - T4CKO260054BK

26” rear 32 aluminium high profile V-Brake CNC machined black 10 mm (3/8”) QR cassette - - T4CKO260055BK

26” front 32 aluminium low profile Disc Brake standard black 10 mm (3/8”) QR - ISO 6 bolts - T4CKO260056BK

26” rear 32 aluminium low profile Disc Brake standard black 10 mm (3/8”) QR cassette ISO 6 bolts - T4CKO260057BK

26” front 32 aluminium high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers - - Panasonic hub dynamo, plugs T4CKO260058SI

26” rear 32 aluminium high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers 3 speed Nexus - hub accessories T4CKO260059SI



28” rear 32 aluminium high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers - - - T4CKO280051SI




28” front 32 aluminium high profile V-Brake CNC machined black 10 mm (3/8”) nuts and washers - - Panasonic hub dynamo, plugs T4CKO280055BK

28” rear 32 aluminium high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers 3 speed Nexus - hub accessories T4CKO280056BK

27.5” front 32 aluminium low profile Disc Brake standard black 10 mm (3/8”) QR - ISO 6 bolts - T4CKO275001BK

27.5” rear 32 aluminium low profile Disc Brake standard black 10 mm (3/8”) QR cassette ISO 6 bolts - T4CKO275002BK



700C front 32 aluminium low profile V-Brake standard black 10 mm (3/8”) QR - - - T4CKO280057BK

700C rear 32 aluminium low profile V-Brake standard black 10 mm (3/8”) QR cassette - - T4CKO280058BK


WHEELS

243

SIZE VERSION HOLE COUNT MATERIAL PROFILE BRAKE FINISH COLOR AXLE MOUNT FREEWHEEL DISC MOUNT EXTRAS CODE

20” front 28 aluminium single wall V-Brake standard silver 10 mm (3/8”) nuts and washers - - - T4CKO200044SI

20” rear 28 steel single wall V-Brake standard silver 10 mm (3/8”) nuts and washers torpedo - cog, lock washer T4CKO200045SI

20” rear 28 aluminium single wall V-Brake standard silver 10 mm (3/8”) nuts and washers thread-on - - T4CKO200046SI








26” rear 32 aluminium high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers thread-on - - T4CKO260052SI






26” front 32 aluminium high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers - - Panasonic hub dynamo, plugs T4CKO260058SI

26” rear 32 aluminium high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers 3 speed Nexus - hub accessories T4CKO260059SI



28” rear 32 aluminium high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers - - - T4CKO280051SI




28” front 32 aluminium high profile V-Brake CNC machined black 10 mm (3/8”) nuts and washers - - Panasonic hub dynamo, plugs T4CKO280055BK

28” rear 32 aluminium high profile V-Brake CNC machined silver 10 mm (3/8”) nuts and washers 3 speed Nexus - hub accessories T4CKO280056BK

27.5” front 32 aluminium low profile Disc Brake standard black 10 mm (3/8”) QR - ISO 6 bolts - T4CKO275001BK

27.5” rear 32 aluminium low profile Disc Brake standard black 10 mm (3/8”) QR cassette ISO 6 bolts - T4CKO275002BK



700C front 32 aluminium low profile V-Brake standard black 10 mm (3/8”) QR - - - T4CKO280057BK

700C rear 32 aluminium low profile V-Brake standard black 10 mm (3/8”) QR cassette - - T4CKO280058BK

INNERTUBES

244

SIZE VALVE TYPE VALVE LENGTH CODE

12.1/2x1.75x21/4 A/V (Shreader) standard T4CDE120010

12.12.1/2x1.75x21/4 D/V (Dunlop) standard T4CDE120011

16 1.75-2.125 A/V (Shreader) standard T4CDE160014

16 1.75-2.125 D/V (Dunlop) standard T4CDE160015

20 1.75- 2.125 D/V (Dunlop) standard T4CDE200023

20 1.75-2.125 A/V (Shreader) 48 mm T4CDE200025

24 1.75-2.125 A/V (Shreader) 48 mm T4CDE240031

24 1.75-2.125 D/V (Dunlop) 40 mm T4CDE240032

26 1.75-2.125 D/V (Dunlop) 40 mm T4CDE260060

26 1.75-2.125 F/V (Presta) 48 mm T4CDE260061

26 1.9 -2.125 A/V (Shreader) 48 mm T4CDE260062

26 1.9-2.125 A/V (Shreader) standard T4CDE260063

27x1.1/4 D/V (Dunlop) 40 mm T4CDE270011

27.5 1.75- 2.125 F/V (Presta) 48 mm T4CDE275001

28 1.75- 2.125 D/V (Dunlop) 40 mm T4CDE280035

28x1 5/8x1 3/8x1 1/4 A/V (Shreader) 48 mm T4CDE280036

28 700 35/38 C F/V (Presta) 48 mm T4CDE280037

28 700 18/28 C F/V (Presta) 48 mm T4CDE280038

RIM TAPERim tape made of PVC protects the tube from being cut by the rim. High pressure resistant - does not deform as rim tapes made of rubber.

Material PCV

Size 20-24”

Dimensions 18 x 0.5 mm

T4CFA200008 20”

T4CFA240008 24”

RIM TAPERim tape made of PVC protects the tube from beeing cut by the the rim.High pressure resistant and does not deform as rim tapes made of rubber.

Material nylon

Size 26” - 29”

Dimensions 18 x 0.5 mm

T4CFA260008 26”

T4CFA280008 28”

T4CFA2750008 27.5”

T4CFA290008 29”


INNERTUBES

245

TIRE REPAIR SET MINIA set for fast and effective repair of inner tubes. The whole process of vulcanization takes 3-5 minutes.

Set of - 6 patches Ø 25 mm - 2 oval patches 25x35 mm - glue 5 g - sandpaper - Dunlop valve rubber insert

T4CKW000021

TIRE REPAIR SET MIDIA set for fast and effective repair of inner tubes. The whole process of vulcanization takes 3-5 minutes.

Set of - 6 patches Ø 25 mm - 1 patch Ø 35 mm - 1 oval patch 35x50 mm - glue 5 g - sandpaper - Dunlop valve rubber insert

T4CKW000022

TIRE REPAIR SET MAXIA set for fast and effective repair of inner tubes. The whole process of vulcanization takes 3-5 minutes.

Set of - 3 patches Ø 35 mm - 3 oval patches 35x50 mm - glue 5 g - sandpaper - Dunlop valve rubber insert

T4CKW000023

TIRE LEVERSSet of 3 levers for removal of the tire. Levers can be hooked onto the spokes for easy tire removal. Made from durable plastic.

Material high tensile plastic composite Set of 3

T4CKW000026

TIRES

246

JAZZRugged tires with tread for riding in challenging conditions. The compound delivers protection against punctures and high durability.

Size 29” x 2.25

I.S.O. (57-622)

Use MTB

Weight

T4COP290002

CONNECTORRugged tires with tread for riding in challenging conditions. The compound delivers protection against punctures and high durability.

Size 29” x 2.10

I.S.O. (57-622)

Use MTB

Weight

T4COP290001

STRAITERRugged tires with slick shaped tread profile providing low rolling resistance, and fair amount of grip on the road. The compound delivers protection against punctures and high durability.

Size 28” x 1.75

I.S.O. (47-622)

Use City

Weight

T4COP280086

DART IRugged tires with classic shaped tread profile providing low rolling resistance, and fair amount of grip. The compound delivers protection against punctures and high durability..

Size 28” x 1 5/8 x 1 1/2 (700x38C)

I.S.O. (40-622)

Use Cross

Weight

T4COP280081

MAPILARugged tires with classic tread profile providing very good grip in the corners and during braking. The compound delivers protection against punctures and high durability.

Size 28” x 1 5/8 x 1 3/8 (700x35C)

I.S.O. (37-622)

Use Cross

Weight

T4COP280085

DART IIRugged tires with classic shaped tread profile providing low rolling resistance, and fair amount of grip. The compound delivers protection against punctures and high durability.

Size 28” x 1 5/8 x 1 3/8 (700x35C)

I.S.O. (37-622)

Use Cross

Weight

T4COP280082

TIRES


DART IIIRugged tires with classic shaped tread profile providing low rolling resistance, and fair amount of grip. The compound delivers protection against punctures and high durability.

Size 28” x 1 5/8 x 1 1/4 (700x32C)

I.S.O. (32-622)

Use Cross

Weight

T4COP280083

LUCERugged tires with smooth tread pattern which guarantees low rolling resistance. The compound delivers protection against punctures and high durability.

Size 28” x 1 5/8 x 1 1/16 (700x25C)

I.S.O. (25-622)

Use Road

Weight

T4COP280084

CONNECTORRugged tires with tread for riding in challenging conditions. The compound delivers protection against punctures and high durability.

Size 27.5” x 2.10

I.S.O. (54-584)

Use MTB

Weight

T4COP275001

WENTRugged tires with smooth tread pattern which guarantees low rolling resistance. The compound delivers protection against punctures and high durability.

Size 27” x 1 1/4

I.S.O. (32-630)

Use Road

Weight

T4COP270010

MOUNT ANGARugged tires with tread for riding in challenging conditions. The compound delivers protection against punctures and high durability.

Size 26” x 2.25

I.S.O. (57-559)

Use MTB

Weight

T4COP260199

MATRIXRugged tires with tread for riding in challenging conditions. The compound delivers protection against punctures and high durability.

Size 26” x 2.25

I.S.O. (57-559)

Use MTB

Weight

T4COP260197

TIRES

248

ROBERRugged tires with tread for riding in challenging conditions. The compound delivers protection against punctures and high durability.

Size 26” x 2.10

I.S.O. (54-559)

Use MTB

Weight

T4COP260198

LINEARugged tires with classic shaped tread profile providing low rolling resistance, and good amount of grip. The compound delivers protection against punctures and high durability.

Size 26” x 2.0

I.S.O. (54-559)

Use ATB

Weight

T4COP260191

WIPERRugged tires with aggressive tread profile providing very good grip. The compound delivers protection against punctures and high durability.

Size 26” x 1.95

I.S.O. (54-559)

Use ATB

Weight

T4COP260185

ASCIARugged tires with classic „butterfly” shaped tread profile providing low rolling resistance, and fair amount of grip. The compound delivers protection against punctures and high durability.

Size 26” x 1.9

I.S.O. (50-559)

Use MTB

Weight

T4COP260188

DARDORugged tires with Z shaped tread profile providing low rolling resistance, and fair amount of grip. The compound delivers protection against punctures and high durability.

Size 26” x 1.9

I.S.O. (50-559)

Use ATB

Weight

T4COP260184

ONDARugged tires with tread profile providing low rolling resistance, which also makes the tire „stick” to the ground. The compound delivers protection against punctures and high durability.

Size 26”x1.75

I.S.O. (47-559)

Use City

Weight

TIRES


SERPENTRugged tires with tread profile providing low rolling resistance, which also makes the tire stick to the ground. The compound delivers protection against punctures and high durability.

Size 26” x 1.75

I.S.O. (47-559)

Use City

Weight

T4COP260187

RATTLERugged tires with tread profile providing low rolling resistance, which also makes the tire stick to the ground. The compound delivers protection against punctures and high durability.

Size 26” x 1 3/8

I.S.O. (37-590)

Use Cross

Weight

T4COP260192

LEXELRugged tires with classic shaped tread profile providing low rolling resistance, and fair amount of grip. The compound delivers protection against punctures and high durability..

Size 24” x 1.9

I.S.O. (50-507)

Use ATB

Weight

T4COP240055

ONDARugged tires with V shaped tread profile providing low rolling resistance, and fair amount of grip. The compound delivers protection against punctures and high durability.

Size 24” x 1.75

I.S.O. (47-507)

Use Junior

Weight

T4COP240054

STRAITERRugged tires with tread profile providing low rolling resistance, which also makes the tire stick to the ground. The compound delivers protection against punctures and high durability.

Size 20” x 1.75

I.S.O. (47-406)

Use Junior

Weight

T4COP200049

FOIRugged tires with smooth tread pattern which guarantees good stick to the ground. The compound delivers protection against punctures and high durability.

Size 16” x 2.125

I.S.O. (57-305)

Use ATB

Weight

T4COP160028

TIRESTIRES

250

TIRES


TIRES

251

252

ACCESSORIESACCESSORIES

PUMPS

254

BORAMade from lightweight CNC machined aluminium alloy. Fitting on water bottle mounts on the frame. Easily adapts to different types of valves. Extracted tube will improve comfort while pumping. Fitted with a cover to protect the valve from dust.

Material CNC machined aluminium

Valve system F/V, A/V

Max pressure 120 PSI

Fastening water bottle mounted clamp

Additional information - Screw-in Clever Valve - for F/V, A/V - frame clamp - valve cover - retractable hose

Length 26.5 cm

Weight 125 g

T4CPO000121

SKEIRONLightweight pump is designed for forks and rear shocks. Easily gets into difficult accessible places thanks to the flexible hose. Lock ferrule on the valve makes inflation very easy. Built-in gauge for easy control of pressure .

Material aluminium

Use for suspension air springs


Additional information - pressure gauge (bar / PSI) - elastic, rotating hose - locking lever - release valve (2 - 3 psi) - anti scratch head

Length 23 cm

Weight 200 g

T4CPO000120

MISTRALMade from lightweight CNC machined aluminium alloy. Fitting on water bottle mounts on the frame. Easily adapts to different types of valves. Extractable hose will improve comfort while pumping. Fitted with a cover to protect the valve from dust.

Material CNC machined aluminium


Max pressure 80 PSI


Additional information - Screw-in Clever Valve - for F/V, A/V - frame clamp - valve cover - retractable hose

Length 23.5 cm

Weight 133 g

T4CPO000122

MATAGIA lightweight pump that can become a companion for each tour. Mount placement water on bottle cage mounts for easy transportation . Lock ferrule on the valve makes inflation very easy. Built-in gauge for control of pressure pumped. T-grip handle will improve comfort while pumping.

Material aluminium

Valve system F/V, A/V, D/V



Additional information - pressure gauge - foldable T-handle grip - frame mount - Velcro strap - locking lever

Length 27 cm - 56 cm

Weight 165 g

T4CPO000119

ACCESSORIES • ACCESSORIES

PUMPS

255

THUNDERThe perfect solution when you don’t have time for a long stop, or when there is not enough room in the jersey pocket. Light weight and dimensions allow you to carry it with you, even on the shortest ride.

Material plastic composite

Valve system F/V and A/V

Max pressure MTB - 35 PSI ROAD -100 PSI

Additional information CO2 16 g cartridge included, compatible with threaded, and non threaded cartridges

Length 14.5 cm

Weight 132 g CO2 cartridge included

T4CPO000114

AQUILOLightweight pump. Mounted using water bottle holes on the frame for easy transport. Lock ferrule on the valve makes inflation very easy. T-grip handle will improve comfort while pumping. Fitted with a cover to protect the valve from dust.

Material aluminium, reinforced plastic composite




Additional information - foldable T-handle grip - frame mount - Velcro strap - locking lever - anti dust valve cover

Length 22.4 cm - 45.5 cm expanded

Weight 130 g

T4CPO000117BK BLACK

T4CPO000117RD RED

T4CPO000117BL BLUE

HABOOBA lightweight pump that can become a companion for each tour. Mounted using water bottle holes on the frame for easy transport. Lock ferrule on the valve makes inflation very easy. T-grip handle will improve comfort while pumping. Has an adaptive valve for F/V and A/V with a cover to protect the valve from dust. Has the ability to customize between road bikes (high pressure) and mountain bikes (high volume).

Material aluminium 6063




Additional information - Clever Valve System - automatic valve - foldable, ergonomic T-handle grip - frame mount - Velcro strap - anti dust valve cover

Additional features - Lockable telescope barrel for High Volume (MTB) and High Pressure (MTB)

Length 26.5 cm - 53.5 cm

Weight 130 g

T4CPO000118

HAMMERHEADMounted using water bottle holes on the frame - for easy transport. Lock ferrule on the valve makes inflation very easy.


Valve system F/V and A/V

Max pressure 80 PSI


Additional information - frame mount - qr clamp head works with Presta or Schrader valves - 2-Tone soft touch handle

Length 24.2 cm

Weight 112 g

T4CPO000109

PUMPS

256

WASPVery light pump, which can become a companion for each tour. Lock ferrule on the valve makes inflation very easy. Pump has an internal container in which you can put for example a set of patches - making it a fully functional repair kit.

Material reinforced plastic composite

Valve system F/V, D/V, A/V

Max pressure 80 PSI


Additional information - frame mount - additional room for tools or tube repair set - locking lever - Thumb-lock

Length 25.6 cm

Weight 76 g

T4CPO000113

HORNETMounted using water bottle holes on the frame for easy transport. This pump has a built in container in which you can put for example a set of patches, making it a fully functional repair kit.


Valve F/V, A/V, D/V

Max pressure 80 PSI


Additional information - frame mount - additional room for tools or tube repair set

Length 23.3 cm

Weight 60 g

T4CPO000112

BUCCAA lightweight pump that can become a companion for each tour. Can be attached to luggage racks with compatible mounts. It is compatible with different types of valves.


Valve system DV, F/V and A/V

Max pressure 80 PSI

Fastening rear rack with pegs (distance 235 mm)

Length 24 cm

Weight 99 g

T4CPO000116


PUMPS

257

TYPHOONProfessional service pump, with a precision, top-mounted, easy to read pressure gauge. Allows for very high pressure and it has a release valve for precise monitoring. Thanks to the large volume of cylinder pumping is very efficient.




Additional information - Clever Valve System - automatic valve - oversized alloy extended barrel for a long stroke - locking lever - top-mounted pressure gauge - release valve - solid base

Height 71 cm

Weight 1668 g

T4CPO000123

STORMService pump, which allows to achieve very high pressure. Thanks to the large volume of cylinder pumping is very efficient.


Valve F/V, A/V, D/V


Additional information - locking lever - ergonomic handle

Length 61 cm

Weight 710 g

T4CPO000111

CYCLONEService pump, with a precision gauge. Allows acheiving very high pressure. Thanks to the large volume of cylinder pumping is very efficient and fast.


Valve F/V, A/V, D/V


Additional information - pressure gauge - locking lever - ergonomic handle

Length 61 cm

Weight 815 g

T4CPO000110

TORNADODurable service pump, with a precision gauge. Allows you to achieve very high pressure. Thanks to the large volume of cylinder pumping is very efficient.




Additional information - easy reading gauge - locking lever - ergonomic handle for better performance

Length 61 cm

Weight 880 g

T4CPO000108

FENDERS

258

ROOKLightweight fender made of plastic. For transport purposes it can be easily disassembled, unfolded, creating a flat surface.


Wheel size 24”-29”

Fastening - rubber straps

Maximum down tube diameter

uni

Weight 77 g

T4CBL260142

HARRIERAdvanced set of lightweight fenders for rapid assembly and disassembly with special adapters. Will satisfy even the most demanding needs of extreme cyclists in a difficult terrain. Special profile with an original, motocross-style optics, designed specially for a new generation of bicycles. When cycling the mudguard turns with the wheel and moves with the suspension fork, at all times remaining within a small distance from tire ensuring optimum protection during ride on all types of terrain. A special fork-shaped design and use of double pivot enables perfect adjustment of the mudguard to frame and wheel profile.


Wheel size 24”- 29”

Fastening - front using SPEEDclick fork adapter - rear using SPEEDstrap seat post adapter

Maximum seat post diameter

uni

Weight 365 g

T4CBL260128BK BLACK

T4CBL260128GP GRAPHITE

T4CBL260128WH WHITE

CROWLightweight fender made of plastic. For transport purposes can be easily disassembled, creating a flat surface.



Fastening - rear using frame adapter


uni

Weight 156 g

T4CBL260143

OSPREYUniversal set of fenders for all types of bicycles. When cycling the mudguard turns with the wheel, at all times remaining within a small distance from tire ensuring optimum protection during a ride on all types of terrain. Double system of adjustment enables ideal positioning of the mudguard in relation to frame and digfferent wheel profiles. Big surface and shape of fenders ensure optimum protection in all cycling conditions.



Fastening - front using SPEEDclick fork adapter - rear using SPEEDstrap seat post adapter


uni

Weight 398 g

T4CBL260129BK BLACK

T4CBL260129WH WHITE


FENDERS

259

HAWKUniversal set of fenders for all types of bicycles. Double system of adjustment for maximum adjustment to wheel alignment and frame type. Big surface and shape ensure optimum protection in all cycling conditions. The fenders have a self-cleaning high polish internal surface.



Fastening - front using Velcro straps - rear using frame adapter


32.8 mm

Weight 331 g

T4CBL260150

TERNClassic set of mountain bike fenders. The mudguards have been adapted for installation with V-Brake brakes. Easy assembly and disassembly with adapters allow fast operation in the event of sudden change of the weather.



Fastening - front using fork adapter - rear using frame adapter

Maximum seat post Diameter

35 mm

Weight 285 g

T4CBL240016

KITEA simple set of fenders suitable for installation with V-Brake brakes. The rear fender has a wide surface that increases protection against mud spray. There is reflective element on the back side of the rear fender which improves visibility and safety of the rider. Easy assembly and disassembly with adapters allow for fast operation in the event of sudden change of the weather.





35 mm

Weight 260 g

T4CBL260151

MERLINSet of fenders designed for bicycles with narrow tire profiles. In order to enhance the comfort, fenders are equipped with modern assembly system using steel wires, which will give them an unusal stability during cycling. Solid mounting points ideal to mount-and-forget. Perfect for those who are going to work in the morning sun and may be coming back in the rain.


Wheel size 28”

Tire width 32-46 mm

Fastening - front to suspension fork arch or classic fork - rear to frame tube with diameter to 40 mm

Weight 312 g

T4CBL280059BK BLACK

T4CBL280059GY GREY

FENDERS

260

LARKFender intended for younger users who are not scared of fast journeys through the puddles.




Weight 138 g

T4CBL160012


RACKS

261

TRAVELRACKLightweight luggage rack mounted to the frame. A convenient size control allows you to adjust it to different shapes and differently sized wheels. Thanks to its construction can be used together with disc brakes.


Material 6061-T6 aluminium

Load 25kg

Use rear

Weight 858 g

T4CBA260078

LIBERTYRACK 200Luggage rack designed to mount to the seat post. When the frame is not with supposed to be used with classic rack when its shape makes this is impossible. Thanks to the QR you can easily remove the luggage rack. Note: do not mount the on seatpost made of carbon fiber.



Load 10kg

Use rear

Weight 683 g

T4CBA000014

WEEKENDRACK 200Lightweight luggage rack mounted to the frame. A convenient size control allows you to adjust it to different frame shapes and differently sized wheels.



Load 25kg

Use rear

Weight 694 g

T4CBA260077SI SILVER

T4CBA260077BK BLACK

LIBERTYRACKLuggage rack designed to mount to the seat post. When the frame is not with supposed to be used with classic rack when its shape makes this is impossible. Thanks to the QR you can easily remove the luggage rack. Note: do not mount the on seatpost made of carbon fiber.



Load 10kg

Use rear

Weight 946 g

T4CBA000013BK BLACK

RACKS

262

FRONTRACK 200Front rack mount on the front fork. Secure transportation system, without affecting the handling characteristics of the bicycle. Placing system panniers close to the axis of the wheel positively affects the location of the center of gravity.


Material aluminium

Load 10kg

Use front

Additional information - for pannier use

Weight 599 g

T4CBA000015

ELSTRAPElastic strap made of high quality rubber. For additional cargo carry on the trunk. Thanks to the large elongation securely holds items, even those of unusual shapes.

Material rubber strap

Fastening plastic hook

T4CGU000024

FRONTRACK 100Front rack mount on the front fork. Secure transportation system, without affecting the handling characteristics of the bicycle. Placing system panniers close to the axis of the wheel positively affects the location of the center of gravity.


Material aluminium

Load 10kg

Use front

Additional information - for pannier use

Weight 599 g

T4CBA000002


BASKETS

263

WICKER 300Made of thickly braided cane, so in addition to the aesthetic appearance of the basket, it has exceptional durability. Mounting system on the handlebar allows you to quickly set up and. Thanks to the practical handle, you can use the basket when shopping.

Material Wicker

Fastening QR mount for handlebar

Dimensions 34x25x24 cm

Weight 1230g

T4CKZT00020

WICKER 100Stylish basket made of wicker. Practical handle allows you to make quick purchases without having to pick up the extra bags. Mounting on the handlebar using hooks allows you to easily install the basket without tools.

Material Wicker

Fastening Handlebar hooks


Weight 660g

T4CKZT00009

WICKER 200Wicker basket perfect for urban bicycles. Quick mounting system and a practical handle allows you to use it as a shopping basket, then easily install it on the handlebar.

Material Wicker



Weight 620g

T4CKZT00019

PICNICA basket covered with a waterproof nylon, closed down from the top, so that goods carried will remain safe during rain. Aluminum frame for light weight makes shopping easier. Shoulder strap and quick mounting system.

Material Bag - nylon, frame - aluminium



Weight 960g

T4CKZT00023BR BROWN

T4CKZT00023VI VIOLET

T4CKZT00023GY GREY

BASKETS

264

F400Made of two types of steel bars. Quick mounting system on the handlebar gives you the ability to easily mount and unmount the basket. Dimensions allow you to carry even a sizable luggage. Available in two colors.

Material steel

Fastening QR „click” handlebar mount


Weight 1150g

T4CKZT00028WH WHITE

T4CKZT00028BK BLACK

F100Sturdy steel basket mounted using the bracket located under the steering wheel bearings. The appropriate size of the basket allows for riding with handbags and a bunch of purchases.

Material steel net

Fastening under headset spacer / front fork


Weight 910g

T4CKZT00010

F200Basket made of steel mesh. Click mounting bracket and practical handle allows for quick shopping, ease of moving the basket. Fitted to the handlebar.

Material steel net

Fastening QR „click” handlebar mount


Weight 983g

T4CKZT00026

R200Rear basket made of steel wires net designed to be mounted on the rear rack. Dimensions allow for carrying large quantities of goods. Can be carried using a practical handle.

Material steel net

Fastening rear rack


Weight 670g

T4CKZT00018


BAGS

265

MAPS BAG 100Mounted by click-release bag for easy access to the maps. It has two pockets for carrying camera. Bag equipped with detachable shoulder strap and a cover for protection from the heavy rain.

Fastening Clip system

Material waterproof Nylon 1680

Additional info main pocket for photo camera, two side and one front pocket, detachable shoulder strap, map pocket, waterproof cover

Size 25.5x13x18 cm

T4CTO000145

DRY POCKETBag designed to carry touch screen mobile phones. A special foil protects phone against weather conditions and provides the ability to use the device. Mounted using plastic O-ring.

Fastening plastic O-ring

Material waterproof plastic composite

Additional info touchscreen compatible

Size 9.5x14.5x1.3 cm

T4CTO000125

TOP BOX 100Waterproof and durable bag attached to the top tube of the frame. Special layer used in the bag allows for the use of mobile phones with touch screen.

Closure Velcro straps

Material waterproof Nylon

Additional info touchscreen compatible

Size 17x8.5x7.5 cm

T4CTO000144

TRUNK BAGThe bag is designed to be mounted on the rack. Made of durable and water resistant material. Mount for lamp and reflective elements are useful in limited visibility.



Additional info reflective piping, strap for rear lamp fastening, zipped main pocket, volume adjustment, shoulder strap

Size 30.5x19x16.5 cm

T4CTO000135

LARGE STRAP 400Durable saddle bag, fitted with buckles. Ideal for small pump, and a set of wrenches. Has an internal pocket to carry small items. Strap for mounting the lights and reflective elements ensure visibility in all conditions.

Fastening Straps w. buckle

Material Polyester 210 denier

Additional info reflective tape, strap for rear lamp fastening

Size 17x8x10 cm

T4CTO000132

MINI STRAP 400Durable saddle bag, fitted with buckles. Ideal to carry repair kit and additional accessories. Has an internal pocket for small items. Strap for mounting the lights and reflective elements ensure visibility in all conditions.


Material Polyester 210 denier

Additional info reflective tape, strap for rear lamp fastening

Size 13x6x8 cm

T4CTO000131

BAGS

266

TOP TUBE BAGWaterproof bag made of nylon. It has two side pockets, so that you can easily carry the necessary tools. Equipped with a removable cover for the phone.



Additional info two zipped pockets w. side pockets, detachable phone pouch

Size side panel 17x4.5x9.5 cm middle panel: 13x7.5 cm

T4CTO000134

SADDLE BAG 100Saddle bag fitted with Velcro straps. Reflective zipper part on the flap.


Material waterproof Polyester 600D

Additional info reflective tape, zipped main pocket

Size 17 x 10 x 8 cm

T4CTO000126BK BLACK

T4CTO000126RD RED

T4CTO000126RDBK RED-BLACK

SADDLE BAG 200Saddle bag with quick mounting system. Equipped with reflective tape for visibility, and two side pockets made of mesh.



Additional info reflective tape, zipped main pocket, 2 mesh side pockets

Size 16x9x9.5 cm

T4CTO000128

TRIANGLE BAGTriangular bag made of waterproof polyester, mounted to frame with Velcro straps. Reflective elements provide visibility in all conditions.



Additional info zipped main pocket, reflective parts

Size 23x20x6 cm

T4CTO000133

LARGE CLIP 300Saddle bag with quick mounting system. Has reflective elements and strap for mounting the rear lamp, so user remains visible in all conditions. Due to the additional zipper the bag has the ability to increase the volume.



Additional info reflective tape, strap for rear lamp fastening, adjustable volume

Size 15.5x9x10.5 cm

T4CTO000130

MINI CLIP 300Saddle bag with quick mounting system. Has reflective elements and strap for mounting the rear lamps, so user remains visible in all conditions.



Additional info reflective tape, zipped main pocket, 2 mesh side pockets

Size 16x9x9.5 cm

T4CTO000129


BAGS

267

FRONT BAGBags made from durable and waterproof nylon. Mounted on the front rack by using holders and straps. The main pockets fastened with adjustable straps. Panniers are equipped with side pockets made of mesh and rain cover.

Fastening Buckle straps


Additional info buckle straps main pocket, 2 mesh side pockets, waterproof cover

Size 36.5x26x17 cm

T4CTO000146

PANNIER BAGBags made from waterproof nylon. Mounted on the rack with buckle straps. Contains smaller zippered pockets. Reflective elements and the light mount will ensure security in all conditions.



Additional info 2 side panniers with small pockets, reflective parts, strap for rear lamp fastening, upper mesh pocket

Size (single pannier) 38.5x11.5x32 cm

T4CTO000136

TRIPLE PANNIER BAGRoomy travel pannier made from waterproof nylon. Detachable upper compartment with dedicated pocket for the map. Reflective elements provide security in all conditions of limited visibility.



Additional info top bag - detachable, two pockets, map pocket, shoulder strap; side bag - main pocket, two side pockets, reflective piping. All pockets with sipper closure.

Size top bag 41x12x35 cm, side bag 29x14x25 cm

T4CTO000147

BACKPACKS

268

AEROBackpack made of nylon for durability and protection against water. Thanks to 2 in 1 function it can be used as a separate backpack with hydration bladder. Ventilated back provides adequate air flow. Hip and chest belts keep backpack in a stable position also during the intense ride. Reflective parts provide visibility during limited visibility.


Volume 20 l

Dimensions 43.5x28x17 cm

Additional information - 2in1 backpack; 1 small cycling pack; 2 hydration pack - padded back and shoulder straps - chest and hip belt - reflective piping

Weight 750 g

T4CTO000122

BUGOver shoulder backpack, made of nylon for durability and protection against water. Attachment system for the helmet and vented back for comfort during use.


Volume 22 l


Additional information - helmet fastening system - ventilated back

Weight 770 g

T4CTO000124

KICKSTANDS

ACCESSORIES • ACCESSORIES269

EMUDurable kickstand with convenient adjustment system to match the size of the wheels, fixed centrally. Made from lightweight aluminum alloy. Thanks to dual the footer provides a stable position of the bicycle at standstill.

Size adjustable 24’’ - 28’’

Mounting location center, behind BB

Material aluminium

Additional information - dual stand - rubber foot

Weight 540 g

T4CPK000161

CRANEDurable kickstand with convenient adjustment system to match the size of the wheels. Attached to the chainstay. Made from lightweight aluminum alloy. Ensures a stable position of the bicycle at standstill.

Size adjustable 24” - 28”

Mounting location chain stay

Material aluminium

Additional information - tool free height adjustment - rubber foot

Weight 320 g

T4CPK000167

HERONRugged stand for comfortable fit system the size of wheels and different angles of the rear triangle. Made from lightweight aluminum alloy. Ensures a stable position of the bicycle at standstill.


Mounting location chain stay / seat stay

Material 6061 T6 aluminium

Additional information - for frames with various angles of the rear triangle - tool free height adjustment - rubber foot

Weight 366 g

T4CPK000157

MARABOURugged stand for comfortable fit system the size of wheels. Made from lightweight aluminum alloy. Ensures a stable position of the bicycle at standstill.



Material 6061 T6 aluminium

Additional information - fits on chain stay with a fixed plate with 2 holes (18 mm ) - tool free height adjustment - rubber foot

Weight 295 g

T4CPK000170

KICKSTANDS

270

FLAMINGODurable kickstand with convenient adjustment system to match the size of the wheels. Attached to the chainstay. Made from lightweight aluminum alloy. Ensures a stable position of the bicycle at standstill.



Material aluminium

Additional information - possibility of mounting on tubes with square profile

Weight 330 g

T4CPK000168

LITTLE EGRETKickstand for children’s bikes with comfortable fit system to match the size of the wheels. Attached centrally behind BB. Made from lightweight aluminum alloy. Ensures a stable position of the bicycle at standstill.



Material aluminium


Weight 186 g

T4CPK000166

STORKDurable kickstand with convenient adjustment system to match the size of the wheels. Attached behind the BB. Made from lightweight aluminum alloy. Ensures a stable position of the bicycle at standstill.



Material aluminium


Weight 310 g

T4CPK000165

IBISDurable kickstand with convenient adjustment system to match the size of the wheels. Attached behind the BB. Made from lightweight aluminum alloy. Ensures a stable position of the bicycle at standstill.



Material aluminium


Weight 210 g

T4CPK000169

LAMPS


GLINTTechnologically advanced, lamp made of aluminium. Rugged and sealed well casing protects against ingress of water, enabling the use in harsh weather conditions. With a LED from aa reputable company CREE. Sensor of battery discharge, loaded via USB. Built-in Smart Sensor Beam light adjusts the brightness to the lighting conditions. Cut off Line Technology to prevent blinding drivers coming from the opposite direction. Intuitive and easy installation allows you to quickly transfer the lights to another bike.

Material aluminium, ABS

Mounting location handlebar


Light source 3W LED CREE XPE R3

Light power 120lm

Illuminance 30lx / 10m

Range 100m

Temperature of emitted light

5500°K~8300°K

Power source 2 lithium batteries LIR17280

Modes - 1 constant - 1 constant power saving

Features - waterproofness IPX4 - tool free fastening - battery capacity sensor - USB charging - Cut off line - Smart Beam - compliant with z StVZO

Weight 87 g

T4COSLP0189WH WHITE

FLUXTechnologically advanced, lamp made of aluminium. Rugged and well sealed casing protects against water enabling the use in harsh weather conditions. Equipped with CREE LED and sensor of battery discharge. Cut off Technology prevent blinding drivers coming from the opposite direction. Variable operating modes allow you to save energy. Intuitive and easy installation allows you to quickly mount the lights to another bike

Material aluminium, ABS



Light source 2.5W LED CREE XPE R3

Light power 110lm

Illuminance 28lx / 10m

Range 90m


5500°K~8300°K

Power source 3 batteries AAA

Modes - 1 constant - 1 constant power saving

Features - waterproofness IPX4 - tool free fastening - battery drain sensor - Cut off line - compliant with StVZO

Weight 76 g

T4COSLP0190BK BLACK

LAMPS

272

SOLARFLARETechnically advanced, lamp with 3 super bright LEDs and 2 side to improve road safety. With the built-in solar panel for charging the battery. Light modes allow you to adjust to different conditions. intuitive and easy installation allows you to quickly move the lights to another bike




Light source 3 super bright LED, 2 side warning LED’s

Light source brightness 20000 mcd

Illuminance 2 lx


8000°K - 35000°K

Power source NI-MH battery solar charged, 3 batteries AAA

Modes - 1 constant - 1 pulse

Features - waterproofness IPX1 - solar panel and Ni-MH battery - battery capacity sensor - tool free fastening

Weight 62 g

T4COSLP0179

FLESHAdvanced light equipped with center LED and 2 side LEDs that provide even greater visibility on the road. Several operating modes allow you to adjust to different conditions. Intuitive and easy installation allows you to quickly move the lights to another bike.




Light source LED 1W, 2 side warning LED’s

Light power 75 lm

Illuminance 8 lux


5500°K - 12000°K

Power source 3 batteries AAA (included)

Modes - 1 constant - 1 constant power save - 1 pulse

Features - tool free fastening - waterproofness IPX1

Weight 87 g

T4COSLP0147SI SILVER

T4COSLP0147RD RED

T4COSLP0147BL BLUE

AGONAdvanced light equipped with center LED and 2 side LEDs that provide even greater visibility on the road. Several operating modes allow you to adjust to different conditions. Intuitive and easy installation allows you to quickly move the lights to another bike




Light source LED 0.5W, 2 side warning LED’s

Light power 35 lm

Illuminance 4 lux


5500°K - 12000°K




Weight 104 g

T4COSLP0146

SPARKAdvanced light equipped with center LED and 2 side LEDs that provide even greater visibility on the road. Several operating modes allow you to adjust to different conditions. Intuitive and easy installation allows you to quickly move the lights to another bike




Light source LED 0.5W, 2 side warning LED’s

Light power 35 lm

Illuminance 4 lux


5500°K - 12000°K




Weight 112 g

T4COSLP0145BK BLACK

LAMPS


PUREThe light made of plastic composite featuring low weight and high strength. Equipped with LED from a reputable company CREE. Lighting modes to adapt to different light conditions. Easy assembly allows you to use the lights in a variety of bikes.




Light source 1W LED CREE

Illuminance 48.5lx / 10m

Light power 40 lm


6500°K - 7500°K



Features - waterproofness - tool free fastening

Weight 95 g

T4COSLP0188BK BLACK

T4COSLP0188WH WHITE

LUMI IILamp made of lightweight plastic composite. Sealed enclosure protects against water, allowing use in harsh weather conditions. Equipped with 3 LED’s with a high service life. Variable operating modes allow you to save energy and to adjust the intensity of light to visibility. Intuitive and easy installation allows you to quickly translate the lights for another bike.




Light source 3 LED 0.5W

Light power 22lm


Range 30m


15000°K~-25000°K



Features - waterproofness IPX4 - tool free fastening

Weight 36 g

T4COSLP0191WH WHITE

T4COSLP0191GY GREY

T4COSLP0191BK BLACK

ECLIPSEStrong light with LED with a very high service life. Lighting modes allow you to adjust to changing conditions. Intuitive and easy installation allows you to quickly move the lights to another bike




Light source 0.5W LED

Light power 20lm

Illuminance 5.2lx


6500°K - 7500°K




Weight 87g

T4COSLP0164BK BLACK

T4COSLP0164SI SILVER

LUMIFront light with super bright LED for high visibility. Different lighting modes allow you to adjust to changing conditions. Intuitive and easy installation allows you to quickly move the lights to another bike




Light source 3 super bright LED’s

Light power 20000 mcd


8000°K~35000°K



Features

- waterproofness IPX0 - tool free fastening

Weight 40 g

T4COSLP0138

T4COSLP0138BK BLACK

T4COSLP0138WH WHITE

LAMPS

274

SILKYLamp made of plastic composite and silicone for quick mounting on the handlebar. Equipped with Nichia LED. Has 3 light modes to adapt to different light conditions. Easy assembly allows you to use the lights in a variety of bikes.

Material silicon + plastic composite


Fastening silicone clamp

Light source 1 Nichia LED

Light power 20000mcd


7000°K~9000°K

Power source 1 battery AA

Modes - 1 constant - 1 pulse - 1 stroboscope


Weight 40 g

T4COSLP0187BK BLACK

T4COSLP0187GRB BRIGHT GREEN

T4COSLP0187RD RED

T4COSLP0187WH WHITE

T4COSLP0187YL YELLOW

RED LINELamp made of lightweight plastic composite, mounted on the seat post. With 3 LEDs and 2 SMD LEDs, to improve visibility. With the built-in sensor for easy control over the degree of discharge of the battery. Easy assembly allows you to use the lights in a variety of bikes.


Mounting location seat post


Light source 3 LED + 2 side SMD (260 degree visibility)



Modes - 1 constant

Features - waterproofness - battery drain sensor - tool free fastening - compliant with K-Mark - compliant with StVZO

Weight 46.5 g

T4COSLT0117

SCOPETechnically advanced lamp with 5 super bright LED’s for high visibility on the road. Lighting modes allow you to adjust to different conditions. Intuitive and easy installation allows you to quickly move the lights to another bike




Light source 5 super bright LED’s


Illuminance 5lux


6000°K~8000°K



Features


Weight 88 g

T4COSLP0186BK BLACK

T4COSLP0186PI PINK

T4COSLP0186RD RED

T4COSLP0186WH WHITE

RED EYELamp is made of plastic composite and silicone for quick mounting on the seat post. Equipped with 2 LEDs, 2 lighting modes allow lamp to work in different conditions. Easy assembly allows you to use the lights in a variety of bikes.




Light source 2 x 0.5W LED


Light power 14.6lm

Power source 1 battery AAA


Weight 92g

T4COSLT0124

LAMPS


LUMI IILamp made of lightweight plastic composite, mounted on the seat post. Sealed enclosure protects against water damage, thus allowing to be used in harsh weather conditions. with 3 LEDs and the sensor battery. Used easy assembly system used, allows you to use the lights in a variety of bikes.




Light source 3 LED

Light power 3lm

Luminous intensity 20000mcd

Power source 2 CR2032

Modes - 1 constant

Features - waterproofness IPX4 - battery indicator - tool free fastening - compliant with StVZO

Weight 22 g

T4COSLT0126

RED SPOTLamp is made of plastic composite and silicone for quick mounting on the seat post. Fitted with 2 LEDs, 2 lighting modes allow lamp to work in different conditions. Easy assembly allows you to use the lights in a variety of bikes.




Light source 0.5W SMD + 2 LED


Light power 3lm




Weight 85g

T4COSLT0096

RED SILKLamp is made of plastic composite and silicone for quick mounting on the seat post. Fitted with 2 LEDs, 2 lighting modes allow lamp to work in different conditions. Easy assembly allows you to use the lights in a variety of bikes.

Material silicon + plastic composite



Light source 2 LED

Light power 10000 - 14000mcd

Power source 1 battery AA



Weight 37 g

T4COSLT0123BK BLACK

T4COSLT0123WH WHITE

SOLARISAdvanced light mounted on the seat post. With the built-in sun panel and internal battery. With LEDs with a high service life. Variable operating modes allow you to save energy and to adjust the intensity of work to visibility. Intuitive and easy installation allows you to quickly move the lights to another bike




Light source 2 LED



6000°K~8000°K

Power source NI-MH battery, solar charged


Features - waterproofness IPX1 - solar panel and Ni-MH battery - tool free fastening

Weight 49 g

T4COSLT0114BK BLACK

LAMPS

276

RED STRIKELamp is made of lightweight plastic composite, mounted on the seat post. With 5 LEDs and 3 light modes to adapt to different light conditions. easy assembly allows you to use the lights in a variety of bikes.




Light source 5 LED’s


Light power 4.5lm


Modes - 1 constant - 1 pulse - 1 sequence

Features


Weight 91 g

T4COSLT0125BK BLACK

T4COSLT0125WH WHITE

CLEAR REDLamp is made of lightweight plastic composite and mounted on the fender by using screws. with 3 LEDs with a high service life.


Mounting location fender

Fastening bolts

Light source 3 LED


Light power 2lm


Modes - 1 constant

Features - waterproofness - built in reflector

Weight 60 g

T4COSLT0121

LIMPID REDLamp is made of lightweight plastic composite, mounted on the seat post. With 5 LEDs and 3 light modes to adapt to different light conditions. easy assembly allows you to use the lights in a variety of bikes.


Mounting location rear rack

Fitting 2 bolts

Light source 3 LED


Light power 2lm

Power source 2 batteries AA

Modes - 1 constant

Features - waterproofness - built in reflector

Weight 100 g

T4COSLT0120RD RED

RED MAGMALamp made of lightweight plastic composite, mounted on the seat post. Sealed enclosure protects against water damage, thus allowing to be used in harsh weather conditions. with 3 LEDs and the sensor battery. Used easy assembly system used, allows you to use the lights in a variety of bikes.



Fastening clamp

Light source 3 LED


Light power 2lm



Weight 87 g

T4COSLT0106

LAMPS


LUMI SET IIPortable lighting set made of plastic composite and silicone for fast installation. Both the front and rear-light equipped with 3 LEDs, providing a high service life. An easy way to mount allows you to use lighting in different bikes.

Material plastic composite + silicon

Mounting location handlebar / seat post


Light source front: 3 LED’s 0.5W / rear: 3 LED

Light power front: 22 lm, rear: 3 lm


15000°K - 25000°K

Power source front - 3 batteries AAA, rear - 2 batteries CR2032 (included)

Modes - 1 constant (front, rear) - 1 pulse (front)


Weight 58 g

T4COS000069WH WHITE

T4COS000069GY GREY

T4COS000069BK BLACK

LUMI SETAdvanced lighting set provided by a very good visibility. Both the front and rear-light with super bright LEDs. Different operating modes allow you to choose the type of light for the requisition. An easy way to mount allows you to use lighting in different bikes.




Light source front: 3 super bright LED / rear: 4 LED

luminous intensity front - 20000mcd, rear - 1000-3000mcd


8000°K~35000°K


Modes - 1 constant - 1 pulse (front) - 3 pulse (rear)

Features

- waterproofness front - IPX0, rear - IPX3

Weight 74 g

T4COS000053 BLACK

T4COS000053BK BLACK

T4COS000053WH WHITE

SCOPE SET IIPortable lighting set made of plastic composite and silicone strap for fast installation. Both the front and rear-light equipped with 3 LEDs, providing a high service life. An easy way to mount allows you to use lighting in different bikes.

Material plastic composite + silicone

Mounting location handlebar / any frame tube

Fastening plastic O-ring / silicone clamp

Light source front: 0.5W LED / rear: 2 LED

Light power front: 25 lm

Luminous intensity rear: 10000-14000mcd


6000°K~8000°K

Power source 2 batteries AAA, 2 batteries CR2025 (included)


Features

- waterproofness front - IPX0, rear - IPX1 - tool free fastening

Weight 88 g

T4COS000070BK BLACK

T4COS000070WH WHITE

T4COS000070GR GREEN

T4COS000070RD RED

T4COS000070BL BLUE

T4COS000070GY GREY

LAMPS

278

TICK SET IILight lighting set made of plastic composite and silicone strap for fast installation. Both the front and rear-light are equipped with LEDs, ensuring high service life. Different operating modes allow you to choose the type of light. An easy way to mount allows you to use lighting on different bikes.

Material silicone + plastic composite

Mounting location any frame tube


Light source 2 LED

Light power front: 20000 - 25000mcd, rear: 10000-14000mcd


6000°K~8000°K

Power source 2 batteries CR2032 (included)



Weight 20 g

T4COS000068BK BLACK

T4COS000068BL BLUE

T4COS000068GRB GREEN

T4COS000068PI PINK

T4COS000068RD RED

T4COS000068VI VIOLET

T4COS000068WH WHITE

T4COS000068YL YELLOW

FRAG SETMaterial plastic composite



Light source 9 LED’s

Luminous intensity 10000 mcd


6000°K~8000°K



Features - waterproofness IPX1

Weight 69 g

T4COS000062

JOLLY SETLight lighting set made of plastic composite and silicone protection against damage. Both the front and rear-light are equipped with LEDs, ensuring high service life. Different operating modes allow you to choose the type of light. An easy way to mount allows you to use lighting on different bikes.

Material silicone + plastic composite

Mounting location any frame tube


Light source 2 LED

Luminous intensity front: 20000 - 25000mcd, rear: 10000-14000mcd


6000°K~8000°K

Power source 2 batteries CR2032 (included)



Weight 20 g

T4COS000067BK BLACK

T4COS000067BL BLUE

T4COS000067GRB GREEN

T4COS000067PI PINK

T4COS000067RD RED

T4COS000067WH WHITE

COMPUTERS


KRC 312WAdvanced wireless cycling computer, with 12 functions. Has the ability to memorize the settings of the second wheel - useful feature especially for those frequent exchanging tires with different widths.KRC312W has also a measurement of the total distance for two bikes. Thanks to the clean and backlit screen it can be used well in the night.

Feature wireless

Functions - current speed - maximum speed - average speed - trip time - trip distance - total trip distance - average vs. current speed - calories - 2 wheel size setting - total trip distance for two bikes - backlight - clock mode 12/24

T4CLI000142

KRC 309WCycling computer with 9 functions, useful for both the tour and the race. With a clear and easy to read display, so user can comfortably read all the necessary values.

Feature wireless

Functions - current speed - maximum speed - average speed - trip time - trip distance - total trip distance - average vs. current speed - calories - clock mode 12/24

T4CLI000141BKBL BLACK-BLUE

T4CLI000141BKRD BLACK-RED

KRC 319WCAdvanced wireless cycling computer, featuring 19 functions. For people who want to control over the intensity of the training there is a cadence meter, for current and the average. Has the ability to memorize the settings of the second wheel - a useful feature especially for frequent exchanging tires with different widths. KRC319WC has also a measurement of the total distance for two bikes. Charge status will be pointed out by the battery indicator. Thanks to the clean and backlight screen it can be used well in the night.

Feature wireless

Functions - current speed - maximum speed - average speed - trip time - day trip - trip distance - total trip distance - average vs. current speed - calories - 2 wheel size setting - total trip distance for two bikes - backlight - auto scan - battery status - cadence current - cadence average - cadence maximum - clock mode 12/24 - auto on/off

T4CLI000144

KRC 315WAdvanced wireless cycling computer, with 15 functions. Has the ability to memorize the settings of the second wheel - useful feature especially for those frequent exchanging tires with different widths. KRC315W has also a measurement of the total distance for two bikes. Has built-in thermometer to constant analysis of temperature. Charge status will be pointed out by the battery indicator. Thanks to the clean and backlight screen it can be used well in the night.

Feature wireless

Functions - current speed - maximum speed - average speed - trip time - trip distance - day trip - total trip distance - average vs. current speed - calories - 2 wheel size setting - total trip distance for two bikes - backlight - battery status - thermometer - clock mode 12/24

T4CLI000143

COMPUTERS

280

KRC 212Advanced wireless cycling computer with 12 functions. Ergonomic design and easy to use menu. with a clear and easy to read display. In addition to the basic function, the cycling computer has a cadence meter, calories burned calculator, and automatic switching function.

Feature wireless

Functions - current speed - trip time - trip distance - total trip distance - maximum speed - average speed - cadence - calories - clock - average vs. current speed - auto function switch - auto start

T4CLI000098

KRC 309Easy to install cycling computer, has an easy-to-use panel. Equipped with a clear and easy to read display, so user can comfortably read the values. Has all the basic features you need for each cycling excursion.

Feature wireless

Functions - current speed - maximum speed - average speed - trip time - trip distance - total trip distance - average vs. current speed - calories - clock mode 12/24

T4CLI000140BK BLACK

T4CLI000140WH WHITE

KRC 307Easy to install cycling computer, has an easy-to-use panel. Equipped with a clear and easy to read display, so you can comfortably read the values. Has all the basic features you need for each cycling excursion.

Feature wired

Functions - current speed - average speed - trip time - trip distance - total trip distance - average vs. current speed - clock mode 12/24

T4CLI000139BK BLACK

T4CLI000139PI PINK

T4CLI000139WH WHITE

COMPUTERS


KRC 108Wired cycling computer with basic functions useful for each trip. Easy to read display with all the needed information.

Feature wired

Functions - current speed - trip time - trip distance - total trip distance - maximum speed - average speed - RPM - calories - clock - stopwatch - auto function switch - auto on/off

T4CLI000138BK BLACK

T4CLI000138GRB BRIGHT GREEN

T4CLI000138OR ORANGE

T4CLI000138WH WHITE

KRC 111Advanced wired cycling computer with 11 functions. Ergonomic design and easy to use menu. with a clear and easy to read display. In addition to the basic function, the cycling computer has a stopwatch and an automatic switching function.

Feature wired

Functions - current speed - trip time - trip distance - total trip distance - maximum speed - average speed - RPM - calories - clock - stopwatch - auto function switch - auto on/off

T4CLI000100SI SILVER

T4CLI000100BK BLACK

LOCKS

282

KZS 550Robust spiral lock, covered with delicate material that protects frame from scratches. Code lock makes it possible for use by several users and does not require additional key. Made of a material with increased resilience, to even better protect the equipment. Built-in light makes it easy to operate during limited visibility.

Lock type 4 digit, resettable code

Length 90 cm

Diameter 12 mm

Head outer material plastic composite

Additional information - additional anti-cut resistance - built-in illumination - exchangeable batteries

T4CZP000186GY GREY

T4CZP000186RD RED

T4CZP000186YL YELLOW

KZS 400Robust spiral lock, covered with delicate material that protects frame from scratches. Code lock makes it possible for use by several users and does not require additional key. Made of a material with increased resilience, to even better protection of equipment.


Length 100 cm

Diameter 10 mm


Additional information - additional anti-cut resistance

T4CZP000188BK BLACK

T4CZP000188BL BLUE




Length 90 cm

Diameter 12 mm



T4CZP000187BK BLACK

T4CZP000187GR GREEN

T4CZP000187PU PURPLE



Length 120 cm

Diameter 12 mm



T4CZP000189GY GREY

T4CZP000189GR GREEN

T4CZP000189RD RED

LOCKS


KZU 250A solid U-Lock which code lock, can be used by several users. Made of reinforced steel and plastic protective cover to protect frame from scratches. Reinforced steel increases resistance to cutting . Dust cover protects the code lock from elements.


Dimensions 146 mm x 227.5 mm

Diameter 16 mm

Head outer material reinforced steel with plastic composite outer casing

Additional information - additional anti-cut resistance - additional anti leverage protection - outer casing features Rubber Finish technology - dust cover

T4CZP000193BK BLACK

T4CZP000193RD RED


KZU 100A solid U-Lock key lock with cover to protect against dust. Made of reinforced steel and covered with plastic to protect frame from scratches.

Lock type flat key

Dimensions 108 mm x 248.5 mm

Diameter 14 mm


Additional information - dust cover - 2 keys included

T4CZP000185BK BLACK

KZU 150A solid U-Lock which code lock, can be used by several users. Made of reinforced steel and plastic protective cover to protect frame from scratches. Reinforced steel increases resistance to cutting . Dust cover protects the code lock from elements.


Dimensions 123 mm x 228 mm

Diameter 14 mm


Additional information - additional anti-cut resistance - outer casing features Rubber Finish technology - holder included

T4CZP000194GY GREY

T4CZP000194BL BLUE

T4CZP000194PU PURPLE

KZS 300Robust spiral lock, covered with delicate material that protects the frame from scratches. Code lock makes it possible for use by several users and does not require additional key. The length of the lock allows securing few bikes at once.


Length 180 cm

Diameter 8 mm


Additional information - anti scratch outer cover

T4CZP000184BK BLACK

T4CZP000184RD RED

T4CZP000184WH WHITE

LOCKS

284

KZS 250Spiral lock, covered with delicate material that protects frame from scratches. Code lock makes it possible for use by several users and does not require additional key.


Length 90 cm

Diameter 6 mm


Additional information - anti scratch outer cover

T4CZP000183BK BLACK

T4CZP000183RD RED

T4CZP000183WH WHITE

KZS 100Spiral lock, covered with delicate material that protects frame from scratches. Code lock makes it possible for use by several users and does not require additional key.

Lock type 4 digit code

Length 90 cm

Diameter 6 mm


T4CZP000181BK BLACK

T4CZP000181BL BLUE

T4CZP000181GRB BRIGHT GREEN

T4CZP000181RD RED

KZS 150Robust spiral lock, covered with delicate material that protects frame from scratches. Code lock makes it possible for use by several users and does not require additional key. The length of the spiral allows securing few bikes at once.

Lock type 4 digit code

Length 150 cm

Diameter 6 mm


T4CZP000182BK BLACK

T4CZP000182BL BLUE

T4CZP000182GRB GREEN

T4CZP000182RD RED

KZK 300Robust spiral lock, covered with delicate material that protects frame from scratches.

Lock type flat key

Length 200 cm

Diameter 6 mm


Additional information - 2 keys included

T4CZP000180BK BLACK

T4CZP000180WH WHITE

LOCKS


KZK 250Robust spiral lock, covered with delicate material that protects frame from scratches.

Lock type flat key

Length 180 cm

Diameter 12 mm



T4CZP000179BK BLACK

KZK 100Spiral lock, covered with delicate material that protects frame from scratches.

Lock type flat key

Length 60 cm

Diameter 8 mm



T4CZP000178BK BLACK

T4CZP000178BL BLUE

T4CZP000178GRB BRIGHT GREEN

T4CZP000178PI PINK

T4CZP000178RD RED


MULTITOOLS

286

MASTER-18The set of tools is an essential part of each cyclist equipment. Light 18-function Multitool that contains the necessary tools for a quick bike service. It will be useful both in the home workshop and on a trip outside the city. Tools were made of high-quality chrome-vanadium steel (CR-V), and aluminum.

Material CR-V steel

No. of functions 18

Tools - Allen keys 2/2.5/3/4/5/6/8 mm - flat screwdriver - Phillips screwdriver PH1/PH2 - chain tool - Torx T25 - box wrench 8/9/10 mm - spoke wrench 14 g/15 g - tire lever

Weight 168 g

T4CKU000095

STARK-8The set of tools is an essential part of each cyclist equipment. A lightweight 8-multitool contains the basic tools for the rapid bike service. It will be useful both in home workshop on a trip outside the city. Tools were made of high-quality chrome-vanadium steel (CR-V).

Material CR-V steel

No. of functions 8

Tools - Allen keys 2/2.5/3/4/5/6 mm - flat screwdriver - Phillips screwdriver

Weight 110 g

T4CKU000130BK BLACK

T4CKU000130BL BLUE

T4CKU000130RD RED

CRUCIAL-11The set of tools is an essential part of each cyclist equipment. Light 11-function Multitool that contains the necessary tools for a quick bike service. It will be useful both in the home workshop and on a trip outside the city. Tools were made of high-quality chrome-vanadium steel (CR-V), and aluminum.

Material steel CR-V, aluminium sides

No. of functions 11

Tools - Allen keys 2/2.5/3/4/5/6/8 mm - flat screwdriver - Phillips screwdriver - chain tool - Torx T25

Weight 180 g

T4CKU000103

FEST-6The set of tools is an essential part of each cyclist equipment. Multitool containing 6 basic tools for quick servicing the bike. It will be useful both in the home workshop on a trip outside the city. Tools were made of high-quality chrome-vanadium steel (CR-V).

Material CR-V steel

No. of functions 6

Tools - Allen keys 3/4/5/6 mm - flat screwdriver - Phillips screwdriver

Weight 138 g

T4CKU000133RD RED

T4CKU000133GR GREEN

T4CKU000133BK BLACK

SHOP TOOLS


CRABPolyethylene handle with ABS for a comfortable grip. Dual removable pin extractor provides longer service life and reliability. Universal type, for IG/HG/UG chains.

Material steel, polyethylene ABS

Use IG / HG / UG chains

Weight 86 g

T4CKU000105

BT-23Spline wrench for freewheel and disc brakes Shimano Center Lock ™.

Material phosphate steel

No. of functions 3

Weight 56 g

T4CKU000136

BT-04Ergonomic and universal nipple wrench. Thanks to the magnet it does not fall with during operation.

Material hardened steel

No. of functions 3

Tools - nipple diameter 3.2/3.3/3.4 mm

Weight 50 g

T4CKU000138

BT-14Spline wrench for Campagnolo ® cassettes and bottom bracket cartridges (Record ™, Chorus ™).


No. of functions 3

Weight 58 g

T4CKU000135

BT-11Spline wrench for Shimano bottom bracket ISIS ™ cartridges.


No. of functions 1

Weight 121 g

T4CKU000137

COVERS

288

BIKE COVERMade of tear-resistant polyester. To protect the bike against the rain, snow, or intense sunlight. Will also work as a protection against dust.

Material waterproof Polyester 170T

Additional information - Velcro closure - compatible with bike locks

Size - L - 195 cm x 77 cm x 90 cm - XL - 200 cm x 70 cm x 98 cm - XXL- 193 cm x 97 cm x 102 cm

T4CTO000142L L

T4CTO000142XL XL

T4CTO000142XXL XXL

WHEEL COVERCover made of waterproof nylon and foam with a pocket for quick release and protect the axle hub. The cover has a pocket for business card.

Material waterproof Nylon w. foam

Wheel size od 26” do 29”

T4CTO000148


WATER BOTTLES

FORENDMade by a reputable manufacturer, Dutch company Tacx. Material from which the bottle is made does not change the taste and smell of beverages. Screw cap prevents fluid loss even when the bottle falls out of the bottle cage.

Material non-toxic plastic composite

Volume 750 ml

Weight 91 g

T4CBI000059WH WHITE

T4CBI000059BK BLACK

FARERMade by a reputable manufacturer, Dutch company Tacx. Material from which the bottle is made does not change the taste and smell of beverages. Screw cap prevents fluid loss even when the bottle falls out of the bottle cage.


Volume 500 ml

Weight 73 g

T4CBI000057BL BLUE

T4CBI000057GPBK GRAPHITE-BLACK

T4CBI000057BK BLACK

T4CBI000057RD RED

T4CBI000057WH WHITE

MOVERMade by a reputable manufacturer, Dutch company Tacx. Material from which the bottle is made does not change the taste and smell of beverages. Screw cap prevents fluid loss even when the bottle falls out of the bottle cage.


Volume 750 ml

Weight 91 g

T4CBI000060BLBK BLUE-BLACK

T4CBI000060RDBK RED-BLACK

T4CBI000060YLBK YELLOW-BLACK

DURARMade by a reputable manufacturer, Dutch company Tacx. Material from which the bottle is made does not change the taste and smell of beverages. Screw cap prevents fluid loss even when the bottle falls out of the bottle cage.


Volume 500 ml

Weight 73 g

T4CBI000058BL BLUE

T4CBI000058BLWH BLACK-WHITE

T4CBI000058GRBK GREEN-BLACK

T4CBI000058RDWH RED-WHITE

T4CBI000058VI VIOLET

T4CBI000058YLBK YELLOW-BLACK

290

WATER BOTTLES

TEAM ISSUE 750Bottle designed for professional users. Transparent material, from which it was made allowes for constant control over the level of the liquid, which is extremely important in the heat of battle on the road. The scale for precise measuring of the quantity of the fluid, mixing drinks- isotonic or post-workout. Bottle was made with the cooperation of KROSS Racing Team and Nutrend nutrition for sportsmen.


Volume 750 ml

Weight 91 g

T4CBI000062

TEAM ISSUE 500Bottle designed for professional users. Transparent material, from which it was made allowes for constant control over the level of the liquid, which is extremely important in the heat of battle on the road. The scale for precise measuring of the quantity of the fluid, mixing drinks- isotonic or post-workout. Bottle was made with the cooperation of KROSS Racing Team and Nutrend nutrition for sportsmen.


Volume 500 ml

Weight 73 g

T4CBI000061


BOTTLE CAGES

TEAM BASKETTransport basket for water bottles, designed to carry a set of 8 bottles of 500 or 750 ml. Makes it easy to provide water bottles on the route of the race, and easy to carry in the car. Works best as support during competitions and sporting events.


Volume 8 bottles

T4CBI000066

STRONGHOLDHigh-quality, durable and very light cage made of titanium. Ergonomic design provides sure grip of water bottle. In set with two screws made of high quality stainless steel.

Material titanium

Fitting 2 stainless steel bolts

Weight 26 g

Additional info compatible with all derailleur mounts/clamps

T4CKZBI0056

LIFFVery lightweight bottle cage made of carbon fiber. Modern shape prevents bottle loss while training. In set with two screws made of high quality stainless steel.

Material carbon


Weight 22 g


T4CKZBI0064

BLADEEAdvanced cage made of aluminum and plastic, which ensures light weight and very high strength. The shape of the basket provides easy access both to draw and inserting water bottle. Holds perfectly, even when the biggest shocks occur. In set with two screws made of high quality stainless steel.

Material aluminium + plastic composite


Weight 24 g

T4CKZBI0048BK BLACK

T4CKZBI0048SI SILVER

T4CKZBI0048WH WHITE

FLEX HOLDERBottle cage made of plastic composite, making it extremely lightweight. In set with two screws made of high quality stainless steel.

Material aluminium + plastic composite


Weight 76 g

T4CKZBI0057

BOTTLE CAGES

292

CLAWBottle cage made of plastic composite, making it extremely lightweight. In set with two screws made of high quality stainless steel.



Weight 35 g


T4CKZBI0061BL BLUE

T4CKZBI0061GP GRAPHITE

T4CKZBI0061RD RED

T4CKZBI0061YL YELLOW

CARTThe classic bottle cage made of aluminium. Provides a sure grip and easily adapts to bottles of different sizes. In set with two screws made of high quality stainless steel.

Material aluminium


Weight 65 g


T4CKZBI0052BK BLACK

T4CKZBI0052RD RED

T4CKZBI0052SI SILVER

T4CKZBI0052WH WHITE

T4CKZBI0052BL BLUE

T4CKZBI0052GP GRAPHITE

GRIDLightweight bottle cage made of plastic composite. Thoughtful design provides a sure grip water of bottle, and ease of access. In set with two screws made of high quality stainless steel.



Weight 33 g


T4CKZBI0062WHBK WHITE-BLACK

T4CKZBI0062WHRD WHITE-RED

T4CKZBI0062BKRD BLACK-RED

T4CKZBI0062BKGP BLACK-GRAPHITE

T4CKZBI0062BKOR BLACK-ORANGE

T4CKZBI0062GRBK GREEN-BLACK

CAGECage dedicated to smaller water bottles. Made of plastic composite, making it extremely lightweight. In a set with two screws made of high quality stainless steel.

Material Aluminium


Weight 44 g


T4CKZBI0053

294

APPARELAPPAREL

HELMETS

296

STIFFAdvanced helmet made in In-mold technology. Thanks to the large number of vents ensures very good ventilation during hot days. Micro System Push is responsible for an easy way to fit into the head. Net placed inside holes protects against insects. Suitable for both mountain biking in the woods and riding a road bicycle on the asphalt roads.

Construction In-mold

Vent holes 25

Fit Micro system

Sizes M (54-58 cm), L (58-61 cm)

Additional information anti bug net

Weight L/290 g

T4CKS000060MRD RED M

T4CKS000060LRD RED L

T4CKS000060MBL BLUE M

T4CKS000060LBL BLUE L

T4CKS000060MGP GRAPHITE M

T4CKS000060LGP GRAPHITE L

T4CKS000060MWH WHITE M

T4CKS000060LWH WHITE L

STOUTHelmet made in In-mold technology. Thanks to the large number of vents ensures proper ventilation of the head during warm days. Easy adjustable with Ring Fit System. Built-in net and the visor protect against insects and branches.


Vent holes 23

Fit Ring Fit System

Sizes M (54-58 cm), L (58-62 cm)

Additional information anti bug net, visor

Weight L/250 g

T4CKS000062MYL YELLOW M

T4CKS000062LYL YELLOW L



T4CKS000062MGR GREEN M

T4CKS000062LGR GREEN L

TIDALHelmet made in In-mold technology. Thanks to the large number of vents ensures proper ventilation of the head during warm days. Easily adjustable with Ring Fit System. Built-in net and the visor protect against insects and branches.


Vent holes 21

Fit Ring Fit System

Sizes M (54-58 cm), L (58-62 cm)


Weight L/289 g


T4CKS000061LGR GREEN L




T4CKS000061LRD RED L

ASCENTHelmet made in In-mold technology. Thanks to the large number of vents ensures proper ventilation of the head during warm days. Easily adjusts thanks to Ring Fit System. Built-in net and the visor protect against insects and branches.


Vent holes 23

Fit Ring Fit System

Sizes M (54-58 cm), L (58-62 cm)


Weight L/250 g

T4CKS000063MVI VIOLET M

T4CKS000063LVI VIOLET L



T4CKS000063MPI PINK M

T4CKS000063LPI PINK L

ACCESSORIES • APPAREL

HELMETS

297

DISTRICTHelmet made in In-mold technology. Thanks to the large number of vents ensures proper ventilation of the head during warm days. Easily adjusts thanks to Ring Fit System. Built-in net and the visor protect against insects and branches.


Vent holes 23

Fit Ring Fit System

Sizes M (54-58 cm), L (58-61 cm)

Weight L/295 g

T4CKS000058MBK BLACK M

T4CKS000058LBK BLACK L



REMOTEHelmet made in Out-mold technology. Easily adapts to the shape of the head with the buckle and Ring System to Fit. With anti-insect net and visor.

Construction Out-mold

Vent holes 14

Fit Ring Fit System

Sizes M (54-58 cm), L (58-61 cm)


Weight L/250 g



T4CKS000065MBL BLACK M

T4CKS000065LBLD BLACK L

COMFYA comfortable helmet made in Out-mold technology. Easily adapts to the shape of the head with the buckle and Ring Fit System . With anti-insect net and visor.


Vent holes 14

Fit Ring Fit System

Sizes M (54-58 cm), L (58-61 cm)


Weight L/250 g


T4CKS000064LGP GRAPHITE L

T4CKS000064MBK BLACK M

T4CKS000064LBK BLACK L



ACEChildren’s helmet made in In-mold technology. Will protect the youngest thanks to superb fit to the shape of the head. with a Ring Fit System and buckle.


Vent holes 14

Fit Ring Fit System

Sizes S (48-54 cm), M (54-58 cm)

Weight M/215 g

T4CKS000057SGP GRAPHITE S


T4CKS000057SBL BLUE S


T4CKS000057SPI PINK S


T4CKS000057SGRB GREEN S

T4CKS000057MGRB GREEN M

HELMETS

298

NETERA lightweight helmet made in Out-mold technology. A large number of vents ensures proper ventilation of the head. Thanks to the Ring Fit, helmet easily adapts to the shape of the head. with insect net and removable visor.


Vent holes 14

Fit Ring Fit System

Sizes M (54-58 cm)

Additional information Additional information: anti bug net, visor

Weight M/245 g



T4CKS000067MVI VIOLET M


TINYA lightweight helmet made for children in Out-mold technology. A large number of vents ensures proper ventilation of the head. Thanks to the Ring Fit System easily adapts to the shape of the head. With a built-in net against insects.


Vent holes 8

Fit Ring Fit System

Sizes S (48-53 cm), M (54-58 cm)

Additional information anti bug net

Weight M/220 g

T4CKS000066SPI PINK S


T4CKS000066SBLB BLUE S

T4CKS000066MBLB BLUE M

T4CKS000066SRD RED S


T4CKS000066SBLD BLD S

T4CKS000066MBLD BLD M


EYEWEAR

299

DX-PROLight weight sports glasses with interchangeable lenses made of polycarbonate. The lenses are made in a spherical technology-that does not have any image distortion at the edge of the lens. Adjustable, removable nosepads allows for a better fit of the glasses..

Frame material TR90

Lens material polycarbonate

Filter UV400

Interchangeable lens (included)

- grey polarized - orange - yellow - transparent

Weight

T4COK000002BKBK BLACK

T4COK000002GRBK GREEN/BLACK

T4COK000002ORWH ORANGE/WHITE

DX-RACELight weight sports glasses with interchangeable lenses made of polycarbonate. The lenses are made in a spherical technology-that does not have any image distortion at the edge of the lens

Frame material TR90


Filter UV400


- grey mirror finish - yellow - transparent

T4COK000004SI SILVER

T4COK000004GR GREEN

T4COK000004YL YELLOW

T4COK000004BK BLACK

SX-RACELight weight sports glasses with interchangeable lenses made of polycarbonate. The lenses are made in a spherical technology-that does not have any image distortion at the edge of the lens

Frame material TR90


Filter UV400


- grey mirror finish - yellow - transparent

Weight

T4COK000003BLWH BLUE/WHITE

T4COK000003SIWH SILVER/WHITE

T4COK000003GRBK GREEN/BLACK


DX-SPTLight weight sports glasses with interchangeable lenses made of polycarbonate. The lenses are made in a spherical technology-that does not have any image distortion at the edge of the lens

Frame material TR90


Filter UV400


- grey mirror finish - yellow

T4COK000006BKWH BLACK/WHITE

T4COK000006BKGR BLACK/GREEN


T4COK000006RDWH RED/WHITE

EYEWEAR

300

DX-OPTICLight weight sports glasses with interchangeable lenses made of polycarbonate. The lenses are made in a spherical technology-that does not have any image distortion at the edge of the lens. Additional adapter for lens enables safe and comfortable use prescription lens..

Frame material TR90


Filter UV400


- grey mirror finish - yellow


T4COK000007GRWH GREEN/WHITE

SX-BBasic light weight sports glasses with lenses made of polycarbonate. The lenses are made in a spherical technology-that does not have any image distortion at the edge of the lens. Adjustable, removable nosepads allows for a better fit of the glasses..

Frame material polycarbonate


Filter UV400


T4COK000001BKOR BLACK/ORANGE


MODEL LENS COLOR

DX-PRO 1

POLARIZED

SX-RACE 1

DX-RACE 1

DX-SPT 1

DX-OPTIC

SX-B


EYEWEAR

301

DX-RACE SPARE LENSInterchangeable lenses made of polycarbonate. Made in a spherical technology-that does not have any image distortion at the edge of the lens.


Filter UV400

T4CLENS0004GP GRAPHITE

T4CLENS0004YL YELLOW

T4CLENS0004TR TRANSPARENT

DX-PRO SPARE LENSInterchangeable lenses made of polycarbonate. Made in a spherical technology-that does not have any image distortion at the edge of the lens.


Filter UV400

T4CLENS0002GPPO GREY POLARIZED

T4CLENS0002OR ORANGE



OPTIC LENSInterchangeable lenses made of polycarbonate. Made in a spherical technology-that does not have any image distortion at the edge of the lens.


Filter UV400


T4CLENS0007OR ORANGE


DX-OPTIC LENS ADAPTERAdapter for prescription lens.


T4CADOPT001

DX-SPT LENSInterchangeable lenses made of polycarbonate. Made in a spherical technology-that does not have any image distortion at the edge of the lens.


Filter UV400



SX-RACE SPARE LENSInterchangeable lenses made of polycarbonate. Made in a spherical technology-that does not have any image distortion at the edge of the lens.


Filter UV400




NOSEPADSComfortable, interchangeable nosepads made of rubber.

Material hypoalergic rubber

Color black

T4CNOSE0002 DX-PRO

T4CNOSE0003 SX-RACE

T4CNOSE0004 DX-RACE

T4CNOSE0006 DX-SPT

T4CNOSE0001 SX-B

T4CNOSE0007 OPTIC

TRANSMISSION

LENS TRANSMISSION(OVER %) MATERIAL FILTR UV

GREY POLARIZED

15% POLYCARBONATE UV 400

GREY


ORANGE


YELLOW


TRANSPARENT


BASELAYERS

302

BASE ZEROBase layer made in seamless technology. Perfectly conforms to the body and wicks perspiration. Special areas with increased breathability simplify heat transfer in places where increased sweating occurs during increased physical exertion. Zones with increased breathability are designed specifically for cyclists and position on the bike. Additional antibacterial properties of fibers used to improve the quality. T-shirt provides maximum comfort with minimal weight.

Material Polyamide

Sizes S/M, L/XL, XXL

T4COD00270SMWH WHITE S/M

T4COD00270LXLWH WHITE L/XL

T4COD00270XXLWH WHITE XXL

BASE TWOBase layer made in seamless technology. Perfectly conforms to the body and wicks perspiration. Special areas with increased breathability simplify heat transfer in places where increased sweating occurs during increased physical exertion. Zones with increased breathability are designed specifically for cyclists and position on the bike. Additional antibacterial properties of fibers used to improve the quality. T-shirt provides maximum comfort with minimal weight.

Material Polyamide/Polypropylene


T4COD00272SMBK BLACK S/M

T4COD00272LXLBK BLACK L/XL

T4COD00272XXLBK BLACK XXL

BASE ONEBase layer made in seamless technology. Perfectly conforms to the body and wicks perspiration. Special areas with increased breathability simplify heat transfer in places where increased sweating occurs during increased physical exertion. Zones with increased breathability are designed specifically for cyclists and position on the bike. Additional antibacterial properties of fibers used to improve the quality. T-shirt provides maximum comfort with minimal weight.

Material Polyamide


T4COD00271SMWH WHITE S/M

T4COD00271LXLWH WHITE L/XL



JERSEYS

303

RACE PROVery light and durable jacket made of Lycra. mesh located in the armpits and full zip will provide ventilation in hot days. Details such as sleeves finished with laser or slider cover provide comfort when riding in all conditions. The necessary things you can put in a deep pocket at the back. Advanced solutions make the jersey is ideal for the most demanding riders.

Material ultra 5™ Lycra® / Dallas™ mesh

No. of pockets 3 + 1 zipped

Sizes S, M, L, XL, XXL

Additional information laser sleeve hem

T4COD000216SBK BLACK S

T4COD000216MBK BLACK M

T4COD000216LBK BLACK L

T4COD000216XLBK BLACK XL


BLACK EDITIONRegular fit cycling jersey made from polyester. With 1/3 length zipper. Sleeves finished with rubber. All the necessary things can be put in a deep, 3-parts pocket.

Material Malaga™ / Brisbane™

Pad polyester 2D


Additional information silicone sleeve hem

T4COD000237SBL BLUE S

T4COD000237MBL BLUE M

T4COD000237LBL BLUE L

T4COD000237XLBL BLUE XL

T4COD000237XXLBL BLUE XXL

T4COD000237SGP GRAPHITE S

T4COD000237MGP GRAPHITE M

T4COD000237LGP GRAPHITE L

T4COD000237XLGP GRAPHITE XL

T4COD000237XXLGP GRAPHITE XXL

T4COD000237SRD RED S

T4COD000237MRD RED M

T4COD000237LRD RED L

T4COD000237XLRD RED XL

T4COD000237XXLRD RED XXL

RACE +Classic style jersey made of Lycra. Adequate ventilation will be provided by full zip and Dallas ™ mesh located in the armpits area . Comfort during the ride is ensured by sleeves finished with laser cut. The necessary things can be put in a deep pockets.

Material ultra 5™ Lycra® / Dallas™ mesh



Additional information laser sleeve hem











T4COD000235SYL YELLOW S

T4COD000235MYL YELLOW M

T4COD000235LYL YELLOW L

T4COD000235XLYL YELLOW XL

T4COD000235XXLYL YELLOW XXL

JERSEYS

304

LEARegular fit cycling jersey made from polyester. With 1/3 length zipper. Sleeves finished with rubber. All the necessary things can be put in a deep, 3-parts pocket.

Material Polyester

No. of pockets 3

Sizes XS, S, M, L, XL

Additional information rubber band hem

T4COD000239XSBL BLUE XS





T4COD000239XSVI VIOLET XS

T4COD000239SVI VIOLET S

T4COD000239MVI VIOLET M

T4COD000239LVI VIOLET L

T4COD000239XLVI VIOLET XL

T4COD000239XSWH WHITE XS

T4COD000239SWH WHITE S

T4COD000239MWH WHITE M

T4COD000239LWH WHITE L

T4COD000239XLWH WHITE XL

ENDURO 3/4Jersey designed for enduro riders. Designed in collaboration with leading Polish enduro riders. Made of elastic and breathable fabric. Provide comfort not only during the demanding downhill, but also during the hike. A specially crafted cut and 3/4 sleeves effectively protect against branches. Profiled sleeve allows you to freely use elbow pads, without restraining movements.

Material

Pad 3D moisture absorbing

Sizes S, M, L, XL

Additional information sleeve 3/4

T4COD000250SGR GREEN S

T4COD000250MGR GREEN M

T4COD000250LGR GREEN L

T4COD000250XLGR GREEN XL









SHORTS AND BIBS

ACCESSORIES • APPAREL305

RACE PROVery light and hard-wearing bib shorts. Made from a various fabrics, easily conform to the body. Comfort during the ride will be provided by 3D pad and elastic shoulder straps. Legs finished with a strip of silicone, which does not allow shorts to move while riding. Advanced solutions make the shorts are ideal for the most demanding riders.

Material Zafiro™ / Shield Endurance™



Additional information silicone hem, Spider mesh braces






RACE PROLong pants with braces, great for riding at low temperatures. Dedicated for XC and road cycling. Made of elastic fabric and membrane with an extra layer on knees. 3D pad provide comfort even during long trips.

Material Giga Elastic™








RACE +Bib shorts with a classic cut made from breathable and elastic fabric. With 3D insert for comfort and good absorption of moisture. Legs have a silicone gripper, so they do not change position while riding.

Material Zafiro™ / Shield Endurance™



Additional information silicone hem, Spider mesh braces
















BLACK EDITIONShorts with suspenders with a classic cut made from elastic fabric. With a convenient 2D pad. Silicone grippers stabilize the legs during ride.


Pad polyester 2D


Additional information silicone hem
















SHORTS AND BIBS

306

ENDURO SHORTSShorts designed for enduro riding. Made from a stretchable fabric. Very light and well vented. Application of mesh in the lining of pockets provided by additional air circulation. Side-zippered pockets allow for extra ventilation or carrying the most important accessories. Clip-in the inner short with pad.

Fabric Polyester / Nylon


Sizes S, M, L, XL













XC SHORTSShorts designed for XC and trail ude. Made from a stretchable fabrics. Very light and well vented. Application of mesh in the lining of pockets provides by additional air circulation. Clip-in the inner short with pad.

Fabric Polyester / Nylon


Sizes S, M, L, XL





LEAShorts for women 3/4 made from elastic and breathable fabrics. Comfortable 2D pad will provide comfort also on long trips. Leg openings finished with silicone gripper, so that that they do not change the position while riding.


Pad polyester 2D

Sizes XS,S, M, L, XL

Additional information silicone hem






T4COD000240XSVI VIOLET XS

T4COD000240SVI VIOLET S

T4COD000240MVI VIOLET M

T4COD000240LVI VIOLET L

T4COD000240XLVI VIOLET XL







JACKETS AND GILETS

307

RACE PROLightweight long sleeve jersey made of elastic fabric. Designed for XC and road bike. Full zip. Ideal to start training, and then with a small size fits in the back pocket. there is a 3-part pocket and an 1 additional zippered to transport the necessary things.

Material Giga Elastic™








RACE PROWarm jacket designed for riding in difficult conditions. Made of three-layer membrane providing comfort while riding at low temperatures. Fully with a full zip. There is a 3-part pocket and an 1 additional zippered to transport the necessary things. Reflective elements will ensure safety during limited visibility.

Material 3 layer membrane


Sizes M,L,XL, XXL

Additional information additional reflective parts





RACE PROLightweight gilet made of breathable membrane. The fabric on the back made of mesh with a very good breathing parameters. There are 2 pockets to transport the necessary . Reflective elements will ensure safety during limited visibility.

Material membrane Flight™ Lycra®

No. of pockets 2


Additional information back made of breathable mesh






RAIN JACKETJacket made from breathable and waterproof material. The perfect „emergency” protection against rain in the event of a sudden collapse of the weather. Will not stand against long rain, but will prevent cooling of the body. Reflective elements will allow for safe return home. Packable in small stow bag.

Material


Additional information additional reflective parts
















WARMERS

308

ARM WARMERSArm warmers made of excellent Italian fabric. Provide excellent protection against the cold and are able to maintain body temperature even when they are soaked. Silicone gripper at the top does not allow warmers to move in relation to the body.

Material Lycra® Lombardia™

Sizes S, M, L, XL

Additional information

T4COD000254S S

T4COD000254M M

T4COD000254L L

T4COD000254XL XL

LEG WARMERSLeg warmers made of excellent Italian fabric. Provide an excellent protection against the cold and are able to maintain body temperature even when they are soaked. Silicone gripper at the top. Zipper at the bottom of warmers for easy wearing.


Sizes S, M, L, XL


T4COD000269S S

T4COD000269M M

T4COD000269L L

T4COD000269XL XL

KNEE WARMERSKnee warmers made of excellent Italian fabric. Provide excellent protection against the cold and are able to maintain body temperature even when they are soaked. Silicone gripper at the top and at the bottom does not allow warmers to move in relation to the body.


Sizes S, M, L, XL


T4COD000268S S

T4COD000268M M

T4COD000268L L

T4COD000268XL XL

ARM WARMERSElastic arm warmers made of a material that provided by protection against low temperatures and little rainfall. Thanks to silicone grippers warmer does not move with the hand. Reflective elements provide security during limited visibility.

Material Lycra®

Size S,M,L,XL

T4COD000256S S

T4COD000256M M

T4COD000256L L

T4COD000256XL XL

WARMERS


LEG WARMERSElastic leg warmers made of a material that provided by protection against low temperatures and little rainfall. Thanks silicone grippers, the warmer does not move with the leg. Reflective elements provide security during limited visibility.

Material Lycra®

Size S,M,L,XL

T4COD000257S S

T4COD000257M M

T4COD000257L L

T4COD000257XL XL

CAPS

310

THERMO COLLAR/CAPBeanie made of two types of fabric. In part around the head it is made of SoftShell-type membrane, and in the upper part of the Lombardia. Thanks to their construction can be easily converted into thermal collar.

Material Lombardia

Size uni

T4COD000258 UNI

THERMAL BALACLAVABalaclava for the most difficult weather conditions. Constructed of SoftShell membrane and fleece. Anatomic cut does not restrict movements of the head. The membrane protects the sensitive spots on the head and fleece provides an adequate level of ventilation.

Material SoftShell+Fleece

Sizes S/ M, L/ XL

T4COD000261SM SM

T4COD000261LXL LXL

THERMAL HEADBANDHeadband made of flexible SoftShell membrane. Anatomic cut to protect the sensitive part of the head and ears. Can be used on the bike and during other activity (running, skiing, etc.).

Material SoftShell

Sizes S/ M, L/ XL

T4COD000262SM SM

T4COD000262LXL LXL

BELGIAN CAPBeanie made from Lombardia. Based on the old Belgian cycling caps, but made of modern materials. The fabric is resistant to spraying water and maintains thermal properties, even when wet. In addition, the visor protects the eyes from rain and snow. When it is worn under the helmet reflective part increases the level of security.

Material Lombardia

Sizes S/ M, L/ XL

T4COD000259SM SM

T4COD000259LXL LXL

HELMET CAPUnder helmet beanie. Constructed of SoftShell membrane and fleece. The membrane protects the sensitive spots on the head and fleece provides an adequate level of ventilation.

Material SoftShell+Fleece

Sizes S/ M, L/ XL

T4COD000260SM SM

T4COD000260LXL LXL

BANDANAUniversal bandana intended to be worn under the helmet. Will provide protection against the wind and little rain. Made of quick-drying material.

Material Polyamide

Sizes UNI

T4COD000246

CAPS


CLASSICClassic cycling cap made of cotton. Protects against wind chill, which threatens cyclists even on warm days. Elastic webbing inside perfectly adapts to the head and absorbs perspiration. Cap also provides excellent protection against insects.

Material Cotton

Sizes uni

T4COD000263BK BLACK

T4COD000263WH WHITE

T4COD000263RD RED

TRUCKER CAPTrucker cap , made of cotton and polyamide. Ideal before or after cycling. Mesh on the provides airflow in warm weather.

Material 60% Cotton, 40% polyamide

Sizes uni

T4COD000266GP GRAPHITE

T4COD000266RD RED

FULLCAPFull Flat Cap made of cotton. Ideal before or after challenging cycling. Protects from the sun and wind. Thanks to the flexible tape easily adapts to the head.

Material Cotton

Sizes S/M, M/L, L/XL

T4COD000265SMWH WHITE S

T4COD000265MLWH WHITE M

T4COD000265LXLWH WHITE L

T4COD000265SMRD RED S

T4COD000265MLRD RED M

T4COD000265LXLRD RED L

SOCKS

312

PRS TEAMClassic, perfect for road cycling. Made of elastic material, conform easily to the shape of the foot. Proper fibers ensure ventilation on demanding climbs and high-speed descents.

Material Polypropylene

Sizes S (36-38), M (39-41, L (42-44), XL (45-47)













PRS MIDThe middle cuff length socks made of elastic material, conform easily to the shape of the foot. Good choice not only for mountain expeditions, but also for tours and in the city.


Sizes S (36-38), M (39-41, L (42-44), XL (45-47)









PRS HIClassic, perfect for road cycling. Made of elastic material, conform easily to the shape of the foot. Proper fibers ensure ventilation on demanding climbs and high-speed descents.


Sizes S (36-38), M (39-41, L (42-44), XL (45-47)










T4COD000275SOR ORANGE S

T4COD000275MOR ORANGE M

T4COD000275LOR ORANGE M

T4COD000275LOR ORANGE L

T4COD000275XLOR ORANGE XL





PRS LOAnkle socks made from elastic material, conform greatly to the shape of the foot. Perfect for warm days.


Sizes S (36-38), M (39-41, L (42-44), XL (45-47)










SHOE COVERS

313

WINTER COVERCycling shoe cover made of 3 mm Neoprene. For protection when walking a strong layer of material on the underside. Provide high thermal comfort with low temperatures. Anatomically placed zipper protect the Achilles tendon. Additional reflective elements increase visibility on the road.

Material Neoprene / PVC

Sizes S (36-38), M (39-41, L (42-44), XL (45-47)

T4COD000276S S

T4COD000276M M

T4COD000276L L

T4COD000276XL XL

RAIN COVERCycling shoe cover made of waterproof material. For protection when walking a strong layer of material on the underside. Protect against water and acts a barrier to mud. Anatomically placed zipper protect the Achilles tendon. Additional reflective elements increase visibility on the road.

Material Polyurethane / Spandex / Nylon

Sizes S (36-38), M (39-41, L (42-44), XL (45-47)

T4COD000277S S

T4COD000277M M

T4COD000277L L

T4COD000277XL XL

GLOVES

314

THERMAL 3FGloves with synthetic fill for thermal comfort. Outer shell is a membrane material to ensure waterproofness and breathability. Long cut, gloves can be worn over the cuff of the jacket and protect against low temperatures (below-10 degrees). Special cut allows free use of bicycle components, and provide maximum thermal comfort.

Material Taslan / Fleece / waterproof membrane

Closure draw cord


T4COD000278S S

T4COD000278M M

T4COD000278L L

T4COD000278XL XL

T4COD000278XXL XXL

ENDUROEnduro gloves, light and very well ventilated. Provide maximum thermal comfort. Only minimalist foam fill on palm side. Silicone printed fingers, indicating the middle and thumb will ensure better control over the brakes,shifters, and suspension adjusters. Velcro closure, for a more secure fit.

Material Spandex / Nylon™ / Polyester

Closure Velcro


T4COD00281SRD RED S

T4COD00281MRD RED M

T4COD00281LRD RED L








THERMAL 5FGloves with synthetic fill for thermal comfort. Outer shell is a membrane material to ensure waterproofness and breathability. Long cuff, can be worn over the jacket sleeve and protect against low temperatures (below-10 degrees).

Material Taslan / Fleece / waterproof membrane

Closure draw cord


T4COD000279S S

T4COD000279M M

T4COD000279L L

T4COD000279XL XL

T4COD000279XXL XXL

XC LITEMinimalistic and ultralight gloves for marathon and XC racing. No padding on the underside for a firm grip and low weight. The top layer is made of a very thin mesh. Without Velcro closure for further weight reduction and increased freedom of movement.

Material Spandex / Nylon™ / Polyester

Closure Velcro












T4COD00282SRD RED S

T4COD00282MRD RED M

T4COD00282LRD RED L









GLOVES

315

ADIUMComfortable gloves with long fingers. The top layer is made of Spandex mesh and Microfiber. Safe and sure handlebar grip will be provided by a non-slip Amara ™ material.

Upper part Spandex mesh , microfiber

Palm part Amara+gel inserts

Closure Velcro

Sizes M, L, XL




SF_NODUSShort finger gloves designed for XC riding. The top layer is made of Spandex mesh and Microfiber - provide adequate ventilation. Non-slip material Amara ™ ensures a secure grip of the handlebar also during most demanding riding conditions.


Palm part Amara

Closure Velcro

Sizes M, L, XL




LF_NODUSLong fingered gloves for XC riding. The top layer is made of Spandex mesh and Microfiber - provide adequate ventilation. Non-slip material Amara ™ ensures a secure grip of the handlebar also during most demanding riding conditions.


Palm part Amara

Closure Velcro

Sizes M, L, XL




PHOTONShort finger gloves. Exceptionally well ventilated thanks to the breathable Spandex mesh. Conforms well to palm shape thanks to 4 direction stretch material. Safe and sure handlebar grip provided by a non-slip Amara ™ material.

Upper part Spandex mesh, 4-Way Stretch

Palm part Amara

Closure Velcro

Sizes M,L,XL,XXL




T4COD000229XXLGR GREEN XXL




T4COD000229XXLR RED XXL

GLOVES

316

CRONShort finger gloves made of breathable Spandex mesh and Microfiber. Safe and sure handlebar grip provided by a non-slip Amara ™ material. Reflective elements increase safety during limited visibility.

Upper part Spandex mesh, microfiber

Palm part Amara

Closure Velcro

Sizes S,M,L,XL









NIZERShort finger gloves made of breathable Spandex mesh and Microfiber. Safe and sure handlebar grip provided by a non-slip Amara ™ material, padded with foam inserts.

Upper part Spandex mesh, microfiber,


Closure Velcro

Sizes S,M,L,XL,XXL





T4COD000232XXLR RED XXL





T4COD000232XXLY YELLOW XXL





T4COD000232XXLB BLUE XXL

NETICShort finger gloves dedicated for women. Made of breathable Spandex mesh and Microfiber. Safe and sure handlebar grip and provided by a non-slip material Amara ™ padded with gel inserts.

Upper part Spandex mesh, microfiber, Amara


Closure Velcro

Sizes XS,S,M,L





T4COD000231XSGP GRAPHITE XL





GLOVES

317

XIALAShort finger gloves dedicated for women. Made of breathable Spandex mesh. Safe and sure handlebar grip provided by a non-slip Amara ™ material.

Upper part Spandex

Palm part Amara

Closure Velcro

Sizes XS,S,M,L





T4COD000234XSBK BLACK XS




LUMARShort finger gloves made of breathable Spandex mesh. Safe and sure handlebar grip provided by a non-slip Amara ™ material, padded with foam inserts.

Upper part Spandex

Palm part Amara

Closure Velcro

Sizes XS,S,M,L,XL,XXL

T4COD000233XSGR GREEN XS





T4COD000233XXLGR GREEN XXL







T4COD000233XSGP GRAPHITE XS






T4COD000233XSYL YELLOW X






GLOVES

318

CUDDLY GIRLShort finger gloves dedicated for children. Made of breathable Spandex mesh. Safe and sure handlebar grip provided by a non-slip Amara ™ material.

Upper part Spandex

Palm part Amara

Closure Velcro

Sizes XXXS,XXS,XS

T4COD000247XXXSPI PINK XXXS

T4COD000247XXSPI PINK XXS

T4COD000247XSPI PINK XS

T4COD000247XXXSBL BLUE XXXS

T4COD000247XXSBL BLUE XXS


CUDDLY BOYShort finger gloves for children. Made of breathable Spandex mesh. Safe and sure handlebar grip provided by a non-slip Amara ™ material.

Upper part Spandex

Palm part Amara

Closure Velcro

Sizes XXXS,XXS,XS

T4COD000248XXXSRD RED XXXS

T4COD000248XXSRD RED XXS

T4COD000248XSRD RED XS

T4COD000248XXXSBL BLUE XXXS

T4COD000248XXSBL BLUE XXS



CHILD SEATS

319

COZYChild seat fitted with a 3-stage adjustable backrest tilt, adjustable harness and foot rests. With a cover for the spokes, to protect the child’s legs. Quick Clamp System for easy assembly and removing. Reflectors on the back of the seat in order to increase visibility. Quick clamp System for easy installation on the frame of the bicycle.

Fastening frame

Max. child weight up to 22 kg

Certificate EN 14344

Color blue, grey

T4CFO000019BL BLUE

T4CFO000019GR GREY

COZY MOUNT BRACKETMounting bracket allows you to install a bike seat in the bike. Quick clamp System for easy removal and installation on the frame of the bicycle.

Compatible seats SW-BC09

Color black

T4CIN000505

SNUGThe child seat with an adjustable harness and foot rests. Cover for the spokes, protect the child’s legs. Quick Clamp System for easy installation on the frame of the bicycle.

Fastening frame

Max. child weight up to22 kg


Color beige, blue, graphite

T4CFO000014BE BEIGE

T4CFO000014BL BLUE

T4CFO000014GP GRAPHITE

SNUG MOUNT BRACKETMounting bracket allows you to install a bike seat in the bike. Quick clamp System for easy removal and installation on the frame of the bicycle.

Compatible seats Bingo, Elibas

Color black

T4CIN000493

KID ACCESSORIES

320

HORNBicycle Horn with a classic look. Made of metal and rubber. It can be easily attached to the handlebar using the clamp/bracket with a screw.

Material steel + rubber

Fastening steel O-ring

T4CKK000015

DOGRingtone-trumpet, made of soft plastic. Thanks to the intuitive operation, child can easily inform the surroundings of its presence.



T4CDZ000070

FISHRingtone-trumpet, made of soft plastic. Thanks to the intuitive operation, child can easily inform the surroundings of its presence.



T4CDZ000071

ELEPHANTRingtone-trumpet, made of soft plastic. Thanks to the intuitive operation, child can easily inform the surroundings of its presence.



T4CDZ000069

PARROTRingtone-trumpet, made of soft plastic. Thanks to the intuitive operation, child can easily inform the surroundings of its presence.



T4CDZ000068

SPRING BASKETLightweight basket made of plastic. Easily mounted on the handlebar using plastic straps - it can be used not only for cycling.


Use handlebar for 12”-20” bikes

Fastening straps

Dimensions 24 cm x 16 cm x 15 cm

T4CKZT00024


KID ACCESSORIES

321

KID SUPPORT 200Universal wheels intended for children’s bikes with wheels of: 12-14-16-18-20 inches. Certified EN 14765.

Material steel

Fastening : on wheel axle - 2 stainless steel bolts

Size 12”-20”


T4CKB000010

BESAFERearview mirror with convex lens providing good overview of what goes on behind the cyclist, a reflector and the LED on the front of the increases visibility on the road.


Features - concave lens - reflector+LED - adjustable - bracket for handlebar mount

T4CLU000017

REPLACEMENT WHEELSA set of wheels-spare part for Kid Support 200.

Material plastic composite and rubber a

Size 12”-20”

Additional information compatible w. Kid Support 200

T4CKB000011

PUSHING RODDesigned to be fitted on the seat post or seat tube of kid’s bike . Allows you teach child and help by holding it in the event of loss of balance.

Material steel

Fastening brace w. bolts

Weight 400 g

T4CIN000509

BELLS

322

I LOVE MYBIKEBicycle bell made of aluminium, it has an easy way to mount. Ringing sound will inform you of the presence of a cyclist.

Material aluminium


Weight 34 g

T4CDZ000054

BEEPBicycle bell made of aluminium. Easy way to fit to the handlebar.

Material aluminium


Weight 18 g

T4CDZ000067

JANGLEBicycle bell made of aluminium. Easy way to fit to the handlebar.

Material aluminium


Weight 31 g

T4CDZ000058

BUZZERBicycle bell made of aluminium. Easy way to fit to the handlebar.

Material aluminium


Weight 18 g

T4CDZ000073

CONCEPTSTORE

324

CONCEPTSTORE

OKŁADKASTORE STANDARD

STOREFRONT

326

OKŁADKASTORE STANDARD

CONCEPT STORE • STORE STANDARD 327

STORE STANDARD

STORE DOWN PROJECTION

328

STORE DOWN PROJECTION

STORE STANDARD


STORE STANDARD

VISUALIZATION

330

STORE STANDARD


STORE STANDARD

PHOTO-WALLPAPERSON WALLS

332

STORE STANDARD

CONCEPT STORE • STORE STANDARD

BRAND CORNER

STAND DOWN PROJECTION

334

STAND DOWN PROJECTION

BRAND CORNER

CONCEPT STORE • BRAND CORNER 335

BRAND CORNER

336

BRAND CORNER

VISUALIZATION

CONCEPT STORE • BRAND CORNER 337

STORE STANDARD

STOREFRONTS

338

STORE STANDARD

DOUBLE-SIDED COFFER87 x 75 cm

OUTSIDE COFFER300 x 75 cm


STORE STANDARD

MAST FLAG100 x 400 cm

340

STORE STANDARD

BICYCLE CATEGORIESGRAPHIC


STORE STANDARD

PHOTOWALLPAPERS

342

STORE STANDARD

STORE COLOUR SCHEME

REDC:0% M:100% Y:100% K:0%R:240 G:0 B:15PANTONE : 485 CRAL: 3020

BLACKC:0% M:0% Y:0% K:100%R:0 G:0 B:0PANTONE: PROCESS BLACK CRAL: 9017

WHITEC:0% M:0% Y:0% K:0%R:255 G:255 B:255RAL: 3020

GREYC:0% M:0% Y:0% K:50%R:157 G:157 B:157PANTONE: COOL GRAY 7 C

GRAPHITEC:0% M:0% Y:0% K:80%R:87 G:87 B:87PANTONE: COOL GRAY 10 C

STEELC:0% M:0% Y:0% K:20%R:218 G:218 B:218PANTONE: COOL GRAY 3 C


STORE STANDARD

STORE EQUIPMENTCOUNTER V1

344

STORE STANDARD


STORE STANDARD

STORE EQUIPMENTCOUNTER V2

346

STORE STANDARD


STORE STANDARD

348

STORE STANDARD

STORE EQUIPMENTCHEST


STORE STANDARD

STORE EQUIPMENTHANDLE FOR CHEST

350

STORE STANDARD

STORE EQUIPMENTSIGN FOR BICYCLE CHEST


STORE STANDARD

STORE EQUIPMENTSHELF FOR BICYCLE

352

STORE STANDARD


STORE STANDARD

354

STORE STANDARD

STORE EQUIPMENTUPRIGHT FOR BICYCLE


STORE STANDARD

STORE EQUIPMENTRACK FOR ACCESSORIES

356

STORE STANDARD

STORE EQUIPMENTPRICE CLIP & PRICE TAG


STORE STANDARD

STORE EQUIPMENTINSIDE FLAG75 x 170 cm

358

STORE STANDARD

STORE EQUIPMENTOUTSIDE FLAG110 x 265 cm


STORE STANDARD

LOGOS USED

ON A BRIGHT BACKGROUND

ON A DARK BACKGROUND

ON RED BACKGROUND

360

STORE STANDARD

“CARBON” BACKGROUND


STORE STANDARD

362

STORE STANDARD

OUTSIDE MATERIALSGATE


STORE STANDARD

OUTSIDE MATERIALSTENT

364

STORE STANDARD

OUTSIDE MATERIALSBALOON


DISTRIBUTORS

366

ALBANIAJANKOVIC-COMP D.O.O.SVETOZARA MARKOVICA 2524430 ADA, SERBIA+381 63 583 429

[email protected]

AZERBAIJANOOO AYDIN SERVISNIFTALIEVA STREET 29/39AZ1063 BAKU+994503129549

[email protected]

BELGIUM2M BIKESRUE DE LUSAMBO 40-521190 BRUXELLES / BRUSSELS+32 496 89 38 17

[email protected]

BELARUSCJSC BIKESETPARTIZANSKII AVENUE 8/11/4220033 MINSK+375 17 2983098

[email protected]

BOSNIA AND HERZEGOVINAJANKOVIC-COMP D.O.O.SVETOZARA MARKOVICA 2524430 ADA, SERBIA+381 63 583 429

[email protected]

BULGARIAVELOZONAIZGREV, BL. 61BURGAS+359 887 804 372

[email protected]

CHILEIBIKES LTDASAN DIEGO 9258330938 SANTIAGO+56 2 26628517

[email protected]

COLUMBIAIBIKES LTDASAN DIEGO 9258330938 SANTIAGO, CHILE+56 2 26628517

[email protected]

CROATIABIKE SPORT D.O.O.MIROSLAVA KRLEŽE 1/242000 VARAŽDIN+42 493 747

[email protected]

CZECH REPUBLICSNOW-HOW ČR S.R.O.ZDĚBRADSKÁ 56251 01 ŘIČANY-JAŽLOVICE+420 323627611

[email protected]

ESTONIAOÜ RADEMARMÕISA 413522 TALLIN+372 6 154 130

[email protected]

FINLANDSIM SPORT OYJOUSITIE 620760 PIISPANRISTI+358 (0)2 275 1400

[email protected]

GERMANYKROSS GMBHHULTSCHINER DAMM 9412623 BERLIN+49 30 565 55 974

WWW.KROSS.PL/[email protected]

HUNGARYBIKING LTDKOLOZSVARI UTCA 641225 BUDAPEST

[email protected]

ICELANDG.Á.P. EHFFAXAFENI 7108. REYKYAVÍK+3545200200

[email protected]

IRELANDCB BICYCLE DISTIBUTIONEASTWAY BUSINESS PARKBALLYSIMON TIPPERARY ROADLIMERICK+353 87 9300002

DISTRIBUTORS

ACCESSORIES • 367

ITALYBICICLETTE CANELLINIDI CANELLINI ERMANO E GIOVANNI SNCVIA CONTRARGINE NORD 1446010 CAMPITELLO DI MARCARIA+39 37 69 64 95

[email protected]

LITHUANIAUAB SALASTATELŠIŲ G. 2LT-90162 PLUNGĖ+370 650 77880

[email protected]

LATVIAAKTIVCENTRS SIAGANĪBU DAMBIS 23B1005 RĪGA+371 26 614 755+371 28 668 983

[email protected]

LUXEMBOURG2M BIKESRUE DE LUSAMBO 40-521190 BRUXELLES / BRUSSELS+32 496 89 38 17

[email protected]

MACEDONIAJANKOVIC-COMP D.O.O.SVETOZARA MARKOVICA 2524430 ADA, SERBIA+381 63 583 429

[email protected]

MOLDOVAPANAMARA S.R.L.BIKESALON KROSSVASILE LUPU STREET 182008 CHISINAU+373 22 857 177+373 69005170

[email protected]

NORWAYLILLAND SPORTS ASSENTRUM 2N-3185 SKOPPUM+47 330 74 851

[email protected]

PERUIBIKES LTDASAN DIEGO 9258330938 SANTIAGO+56 2 26628517

[email protected]

PORTUGALCASTANHEIRA & CASTANHEIRA LDARUA DA MALAPOSTA S/N4905-642 VILA DE PUNHE, VIANA DO CASTELO+351 258 971 216

WWW.CASTANHEIRACASTANHEIRA.PT

ROMANIAS.C. KERO BRINGA S.R.L.BECLEAN STREET 19535600 ODORHEIU SECUIESC+40 266 217 430+40 731 371 384

[email protected]

SERBIAJANKOVIC-COMP D.O.O.SVETOZARA MARKOVICA 2524430 ADA+381 63 583 429

[email protected]

SLOVAKIAEXISPORT S.R.O.OPATOVSKA CESTA 14040 01 KOSICE+421 918707473

[email protected]

SPAINBICICLETAS QÜERC/ MESTRE JOAQUÍN RODRIGO, 2046510 QUARTELL, VALÈNCIA+34 96 26 36 412

[email protected]

SWEDENCYKELKRAFT ABPROPELLERVÄGEN 8A18362 TÄBY+46 8 7920661+46 8 154170

[email protected]

SWITZERLANDWWD WIDE WORLD DESIGNS LLCFREIE STRASSE 88POSTFACH 2009CH-4001 BASEL+41 789077373

[email protected]

UKRAINEVELOMAN-EXTREMEKAMENETSKAYA STREET 6829000 KHMELNITSKIY+3 (097) 942 49 06

[email protected]

NOTES

368

Date post:	07-Apr-2016
Category:	Documents
Upload:	castanheira-castanheira-lda
View:	256 times
Download:	20 times

Catálogo Kross Parts 2015

Documents