Catalogo - Techlok

7/26/2019 Catalogo - Techlok

1/30

VECTORINTERNATIONAL

Clamp Connector Technology

thewayforward


2/30

2

Clamp Connectors

- The Obvious Choice .............. 4

How it Works ......................... 5

The Techlok Advantage............ 6

Applications ........................... 7

Maintenance and

Fabrication............................. 7

Assembly and

Dis-Assembly.......................... 8

Sealrings................................ 9

Butt Weld Hubs.................... 10

Blind Hubs........................... 12

Clamps ................................ 14

Quality,Type Approval

and Testing .......................... 16

The Techlok

Product Range...................... 18

Pressure Temperature Ratings

- Carbon Steel ...................... 20

- Stainless Steel.................... 22

- Duplex Steel....................... 24

- Super Duplex ..................... 26

Selecting A Techlok

Connector ................ Inside Flap

Order/Quotation

Procedure ................ Inside Flap

Design

Consultancy ........... Outside Flap

Our Background

Techlok was founded in 1987, and

rapidly established itself as one of the

market leaders in clamp technology in

the North Sea Oil and Gas industry.

Since its foundation, the company hasalways striven to be in the forefront of

technological development,

manufacturing expertise and customer

service. Over the years its technological

expertise and range of services

expanded well beyond the Techlok

clamp connector product.

So, in 1995, the company restructured

under the new identity of Vector

International - Vector to signify our

forward movement in the industry, and

International to reflect the ever

expanding scope and breadth of the

services we offer our clients.

Today Vector International remains

committed to maintaining its high-

profile worldwide presence, with head

office in the UK and operational arms in

Scotland, Norway, Middle East and

USA, offering local expertise, tuned to

local conditions and requirements, with

products and services geared to local

industry needs.

Contents The Techlok range of clampconnectors is manufactured by

Vector International, the

industrys leading independent

manufacturer and supplier ofhigh performance, low weight

proven sealing technologies for

onshore, offshore & subsea

pipeline applications.

Techlok clamp connectors are available as standard from 1" - 24" and supplied in a wide range of

materials from Carbon Steel through to Duplex Steel and Nickel Alloys.


3/30

3

VECTORINTERNATIONAL

Our Strengths

Vector International is far more than

a supplier of advanced technology

sealing solutions.- We are

specialists.

We have a proven technical

capability.

An innovative outlook.

A dedicated manufacturing facility.

A strong engineering bias

A specialist trouble shooting team.

Fully equipped R & D facilities.

An established cost-effective

product range.

Experienced, dedicated

professionals, working across abreadth of industries developing

lasting, effective business

relationships.

And our track record proves it.

Our Credentials

Vector International is a major supplier

of services and equipment to leading

international offshore and onshore oil

companies worldwide.

The industries served include:

OIL AND GAS EXPLORATION

PETROCHEMICAL

REFINING

POWER GENERATION

AEROSPACE

Our Commitment

Vector International is a company with a

lot to offer.

This brochure sets out to show the full

range of Techlok products and services.

What it can't do is to show you the

degree of commitment and enthusiasm

we bring to every project we are

involved in - from a major collaboration

on technologically advanced high

pressure systems to prestigious on-going

maintenance and supply contracts with

the leading oil and gas explorers

worldwide.

That you will have to experience foryourself.


4/30

4

Save Weight - Save Money

Weight equals cost.

Techlok clamp connectors offer major

weight savings over standard ANSI flanges.

All offshore operators know about the need

to minimise platform topside weight to

reduce overall installation costs. For

offshore applications Techlok is the only

choice, with substantial weight savings

being realised even on smallerdevelopements - and these savings are

applicable across all industries where

weight is a consideration.

So wherever weight is a factor, Techlok

clamp connectors are the only sensible

solution.

Save Time - Save Money

Time equals cost.

Conventional flanges have eight or morebolt holes which have to be properly

aligned to make an effective seal.

Techlok clamps have only four bolt holes,

no alignment problems, and reduced bolt

loads.

So not only can Techlok save up to one-

third of the time spent assembling

conventional flange systems, they also

dramatically reduce down-time - with

savings of up to 1m recorded.

Save Space - Save Money

Space equals cost.

Techlok clamp connectors are significantly

smaller than comparable conventional

flanges.

And unlike conventional flanges Techlok

clamp connectors are bolted radially, not

along the axis of the pipe.

With no bolt holes to align the Techlokconnector can be oriented in any position

around the axis of the pipe, avoiding

potential clearance problems, it also

enables more components to be compacted

into the same space. Critical components

like valve hand wheels may be aligned

more efficiently for optimum positioning

before fully tightening the clamp bolts.

Save Leakages - Save Money

Leakage equals cost.

It can also have an enormous

environmental impact.

External bending moments are always

present in any piping system, invariably

resulting in high stresses at the pipe joints.

Strain gauge and destructive tests have

shown Techlok connectors can withstand

considerable bending moments/forces and

axial loading under pressure, without

leakage or bolt loosening. Data sheets are

available giving external load factors, Vector

International can also supply specific

customer requirements on request.

You cannot over overload or crush a

Techlok Sealring. Once initial make-up is

achieved, the seal is self energised with

essentially elastic deformations, and is

made even more effective by internal

pressure - so much so that the Sealring can

normally exceed the burst pressure of the

connected pipe.

So Techlok clamp connectors can withstand

severe bending without leakage or the need

for periodic retightening, thereby reducing

maintenance costs and protecting the

environment.

The design of conventional flanges hasremained unchanged for more than fifty

years. Around thirty years ago the clamp

connector was developed as a high-pressure,

low-weight alternative to flanges. Its

continued success has encouraged

increasing application in a widespread range

of industries where its performance and

economic and environmental advantages are

increasingly being realised.

Techlok high pressure clamp connectors

incorporate a proven metal-to-metal sealing

concept which combines the strength and

integrity of a welded joint with the versatilityof a mechanical joint.

The product range has been categorised into

three separate duty ratings - standard, light

and heavy - reflecting the size designations

developed over the years in a logical range

for ease of use, and to provide the optimum

solution for all pressure requirements.

Clamp Connectors - The Obvious Choice

In twenty-five years of reliable service the clampconnector has become a must for onshore, offshore

and subsea pipeline installations.

Fully Assembled

Pressure Energised Seal

Prior to Assembly

Self Energised Seal

Techlok 4 31 Sch. xxs connector

- Total weight = 23.8Kg

ANSI 4" 2500LB Sch. xxs flange

Total weight = 141.9Kg


5/30

Hubs

The two hubs are manufactured from the same generic

material as the piping system. They are then

welded to the pipe section or machined

integrally onto associated equipment such as

valves. A critical feature of the hub is

the conical seat which creates

the interference with the

sealing lips to effect the seal.

Butt weld hubs

are supplied

with standard

ANSI B16.25

weld profiles.

Blind hubs, are also

available as a means of

blanking off a pipe section,

or for pressure vessel

closures.

5

How it Works

Bolts

Techlok clamp connectors utilise standard grade bolts and nuts in a variety of coatings to suit every

application. Each connector only requires four bolts which include a 100% redundancy factor.

All bolts are provided with spherical-faced nuts to eliminate bending stresses in the bolts

during assembly.

The Techlok concept, unlike conventional

flange design, does not rely on the bolting

to maintain seal integrity during service.

The applied loads are transmitted to the

clamp segments via almost full 360

contact with the hubs, the transverse

bolting being virtually isolated from the

operating loads giving a strong, reliable

yet compact connection.

SealringThe sealring is the heart ofthe Techlok system and

provides many advantages over

conventional gaskets such as:

Minimal gasket forces and seal

diameter, enabling the load capacity

of the components to be maximised.

Reliable and proven pressure-

energised bore seal concept.making

the Techlok connector compact and

up to 75 per cent lighter than

comparably rated flanges.

Gas tight metal to metal seal.

The ring consists of a central rib section

and two seal lips which are tapered to

match the conical seat profile of the

hubs. It is these lips which provide the

pressure-energised seal, as shown in

(page 4), with deformation remaining

essentially elastic throughout, and

making the sealring reusable.

Clamps

The two clamp segments make nearly 360 contact round the hub flange. The seal is

made when the bolts are tightened, drawing the two clamp halves together, and

clamping the hubs against the seal ring. The clamp bolt holes are also supplied with

spherical seats to accept the spherically faced nuts.

The rib acts as a positive

stop during makeup,

prevents the lips from being

crushed by overtightening,

and transfers compressive and

bending loads from one hub to

the other.

Coating the sealring with a lubricant such as

PTFE or MoS2 prevents the surfaces galling during

makeup and enhances its reusability.

The ring is manufactured from high strength steel

compatible with the hub materials. Typically precipitation

hardening stainless steels, such as grades 630 or 660, or Alloy

718, are specified for corrosion resistant applications, while low

alloy steels are used for carbon steel pipelines.

The Techlok clamp connector is a compact mechanical joint consisting of four basic elements: hubs,

seal ring, clamps and bolting. During assembly the hubs are drawn together under the twin wedge

action of the clamp segments to provide the initial self-energising seal.


6/30

6

Unlike conventional flanges, Techlok

connectors do not rely directly on

bolting to maintain seal integrity. Loads

are transmitted to the clamp segments

via almost full 360 contact with the

hubs, the bolting being virtually isolated

from the operational loads. Each

connector requires only four bolts which

includes a 100 percent safety/

redundancy factor.

Techlok connectors also excel in high

pressure applications, with working

pressures of 30,000 psi not unknown.

The Benefits

Techlok clamp connectors are high-

performance products, competitively

priced to provide a superior alternative

to standard flanges for the Industrial

and Offshore sectors.

Their many advantages over

conventional flanges make Techlok

connectors obvious choice where time,

cost and operating efficiency are

paramount:

Up to 75% lighter and significantly

smaller than a comparable ANSI or

API flanges.

Close piping and hook-up

arrangements with typically 25%

smaller clamp diameter.

Typically 40% shorter connection

length.

Easier fabrication and installation

with no bolt holes to align.

Only 4 bolts to tighten rather than

up to 24 on a conventional flange.

The clamp can be rotated

completely round the hub for easy

bolt orientation and tightening.

Ancillary components such asvalves and piping layouts can be

installed without regard to bolt hole

alignment.

Quicker and easier assembly and

disassembly, minimising

maintenance downtime.

Far lower bolt torque required -

typically 50 percent less than that

for a ring joint flange.

Sealing integrity is unaffected by

over-tensioning bolts.

Short make and break times -

several Techlok connectors can

usually be assembled or

disassembled in the time it takes for

a single flange connection.

It is not usually necessary to re-

tighten bolts once in service.

In most cases only one clamp size

is required for each pipe size.

Unlike spiral-wound gaskets,reusable sealrings give greater

flexibility for hydro testing and

commissioning prior to service.

Reduced inventory.

Readily available machining details

for interface with associated

equipment such as valves and

pumps.

Approval and Support

Techlok connectors are approved and

supported by

Full Type approvals from Bureau

Veritas.All current Industry Standards for

interchangeability:

Backed by experienced professional

personnel to support individual

piping and system applications

High-tech international company

accredited with BS EN ISO 9001 -

1994.

Manufacturing facility dedicated to

Vectors wide range of pipe sealing

productsLarge stock of finished parts

strategically placed world-wide.

Severe Working Conditions

Techlok connectors can withstand

severe working conditions.

Pressures of up to 30,000psi

2069 bar.

Temperatures of between

-425 to 1750F (-254 to 950C)Bending.

Tension.

Vibration.

Thermal and mechanical shock.

Competitively Priced

Vector International's successful track

record together with our engineering

skills and experience enables us to

operate a cost-efficient productionfacility with keenly priced products. We

offer all our customers:

A standardised range of products

available from stock.

A standard range of material

specifications ensuring consistant

availability.

Effective solutions for most pipeline

requirements.

A competitive price structure.

The Techlok AdvantageFor many years the offshore, petrochemical and nuclear industries

have recognised the ability of clamp connectors to withstand

severe bending without leaking or the need for periodic re-

tightening of the bolts. These advantages are now available to the

wider industrial market


7/30

7

Wherever flanges are used, a Techlok clamp connector provides a suitable alternative whatever the

industry application. Typical applications include:

Applications

Petrochemical

Power GenerationOffshore

Aerospace

Industrial Piping

Oil and Gas Production

Maintenance

Properly assembled Techlok connectors

do not need any special maintenance.

Always protect exposed hub seat

surfaces with suitable corrosion resistant

coating when being stored or not in use.

When reassembling a connector the seal

ring should be checked for stand-off,

and the hub seats should be checked to

ensure that they are free from burrs and

scratches which could cause the

component to leak.

If burrs, scratches, rust or scale are

found they may be removed by lightly

polishing with a fine abrasive wet or

dry paper around the ring seat

circumference. Ensure that the reworked

area blends in uniformly.

Do not lap the hub seat with the seal

ring: both the ring and the seat will be

damaged, and it will not be possible to

make an effective seal.

Do not tighten the connector while it is

subject to pressure or severe mechanical

loads.

Clamps and seals must not be

welded without checking with Vector

International.

Substituting non Techlok parts will void

all warranties. Components should be

obtained only from Vector International

or an authorised distributor.

Fabrication

Techlok hubs can be fabricated to

piping or other component equipment

using established welding procedures.

Particular attention should be paid

during fabrication (welding) to

minimise angular misalignment of the

hub face.

Care must be taken to protect the hub

seat from damage (for example

scratching and weld spatter).

When required, stress relieving of

carbon and low alloy steel hubs must

be carried out in compliance with

applicable industry codes and

requirements.


8/30

8

Assembly and Dis-Assembly ProcedureDIS-ASSEMBLYASSEMBLYDE-PRESSURISE THE LINE

Always check, never take it for granted that the l inehas been de-pressurised. Proceed with caution incase seepage has caused pressure to build up again.

SLACKEN NUTS BUT DO NOT REMOVE THENUTS FROM THE BOLTS - THEN SLACKENCLAMP SEGMENTS

Gradually run the nuts back along the bolts until justloose. If clamp segments remain bound onto hubs,then BOTH segments must be slackened by hitting theinner face of the clamp lugs with a suitable hammer.

REPEAT SLACKENING PROCEDURE

Re-loosen nuts and re-slacken BOTH clamp segmentsuntil the maximum nut travel shown below is reached.This should release seal ring contact and any residualpressure will then be released through, with the joint.

0

2000

4000

6000

8000

10000

1 2

0 0 0

14000

1500

0

200

400 600

800

1000

X2X

X

ALWAYS ASK YOURSELF - WHAT IF ?What if, the clamp is still under pressure, am I or others in danger, and if so how?What if, there is still gas or fluid in the line.What if, the sling snaps.What if, the load swings in my direction.What if, the piping springs upon release. (Piping spring may also prevent free

rotation of clamps around the hubs).

CHECK CLAMPS ARE SLACK AND FREE TO

ROTATE AND/OR ROCK ABOUT HUBS

Do not proceed until discharge ceases AND clamps areslack, free to rotate or rock. NOTE - If pressure is stillin the line, the sealring might remain seated, makingthe joint tight even though it is part dis-assembled.ONLY when clamps are free to move can dis-assemblybe completed. If the clamps are not free to moveDO NOT CONTINUE - contact your supervisor.

X = Nut travel at each end of bolt

2X = Total nut travel fromassembled position

INSPECT COMPONENTS PRIOR TO ASSEMBLY

Hub and seal ring seating surfaces must be cleanand free from foreign matter. Damage to hubseats and seal lips is not acceptable, and should berectified before assembly.

LUBRICATE

Usually seal rings are coated which acts aslubricant during make-up. If required light oil orMoS 2 spray can be used. Take care that no solidparticles are present in the lubricant.

CHECK SEALRING STANDOFF

The sealring should rock slightly against hub face.Stand-off dimensions given below in inches.

ASSEMBLE COMPONENTS

Install sealring into the hubs, and assemble clampsaround the hubs. Lubricant applied to thehub/clamp contact area will aid assembly. Thestudbolts should be fitted ensuring that sphericallyfaced nuts locate into spherical seats of the clamps.Lubrication of nut faces and bolt threads isrecommended.

TIGHTEN BOLTS IN UNIFORM MANNER

Bolting should be tightened to keep spacing betweenclamp halves approximately equal. Clamp segmentsshould be shocked with suitable soft faced hammer

to aid assembly. Always re-tighten bolts aftershocking to the torque/preload values given below.

ALIGN HUBS

Hubs should be aligned so that seal ring can beinstalled between hubs. DO NOT attempt to correctbadly mis-aligned piping by clamping force alone;piping pulling forces should only be released whenclamp is fully assembled.

SEAL

RING

4

5

7

11

12

13

1416

20

23

25

NOMINAL

STANDOFF

CANTED

0.018

0.018

0.021

0.025

0.025

0.025

0.0240.024

0.023

0.025

0.028

MIN

CANTED

STANDOFF

FOR RE-USE

0.006

0.006

0.007

0.009

0.009

0.009

0.0080.009

0.011

0.013

0.014

27

31

34

40

42

46

52

56

62

64

67

72

76

0.032

0.031

0.036

0.039

0.042

0.050

0.050

0.053

0.092

0.096

0.096

0.099

0.103

0.016

0.015

0.018

0.019

0.021

0.025

0.025

0.026

0.046

0.048

0.048

0.050

0.052

82

84

87

91

92

94

97

102

106

112

116120

122

124

130

0.107

0.111

0.114

0.118

0.118

0.122

0.129

0.129

0.137

0.144

0.1480.155

0.155

0.152

0.167

0.053

0.055

0.057

0.059

0.059

0.061

0.065

0.065

0.068

0.072

0.0740.078

0.078

0.076

0.083

134

137

140

144

152

160

170

180

185

192

200210

220

225

232

0.167

0.163

0.167

0.193

0.189

0.193

0.200

0.207

0.219

0.230

0.2340.224

0.254

0.261

0.272

0.083

0.081

0.083

0.096

0.095

0.096

0.100

0.104

0.109

0.115

0.1170.112

0.127

0.130

0.136

These values are the minimum recommended. Fornormal piping fabrication increase values by 1.5.

For severe piping mis-alignment increase values by2.0 except for thin walled hubs - contact Vector

International for assistance.

LUBRICATED UNLUBRICATED

CLAMP SIZE FT-IBS Nm FT-IBS Nm

STANDARD CLAMP SERIES

1" 17 23 26 35112" 35 47 53 712" 55 75 83 1123" 60 81 90 1224" 90 122 135 1835" 140 190 210 2856" 200 271 300 4078" 300 407 450 610

LIGHT DUTY SERIES

L14" 650 881 975 1322L16" 900 1220 1350 1830L18" 1200 1627 1800 2440L20" 1300 1762 1950 2644L24" 1850 2506 2775 3762

HEAVY DUTY SERIES

H2" 90 122 135 183H3" 100 136 150 203H4" 140 190 210 285H8" 390 529 585 793H10" 600 813 900 1220H12" 900 1220 1350 1830H14" 1200 1627 1800 2440H16" 2000 2711 3000 4067H18" 2000 2711 3000 4067H20" 2000 2711 3000 4067H22" 2000 2711 3000 4067H24" 2000 2711 3000 4067H26" 2000 3389 3750 5084

X 2X

CLAMP SIZE INS MM INS MM


1" 0.1 3 0.2 5112" 0.1 3 0.2 62" 0.1 3 0.2 63" 0.2 4 0.3 84" 0.2 5 0.4 10

5" 0.3 7 0.6 146" 0.5 12 1.0 248" 0.5 13 1.1 27

LIGHT DUTY SERIES

L14" 0.6 16 1.3 33L16" 0.7 17 1.3 33L18" 0.7 17 1.3 33L20" 0.7 17 1.3 34L24" 0.8 20 1.6 39

HEAVY DUTY SERIES

H2" 0.1 3 0.2 6H3" 0.2 4 0.3 8H4" 0.2 5 0.4 11H8" 0.5 12 0.9 24H10" 0.6 16 1.2 32H12" 0.7 19 1.5 37H14" 0.8 20 1.5 39H16" 0.8 20 1.6 40H18" 0.8 21 1.7 42H20" 0.8 22 1.7 43H22" 0.9 22 1.7 43H24" 0.9 23 1.8 45H26" 0.9 23 1.8 45

CROSS REFERENCE TABLE

CLAMP SIZE GR STANDARD SIZES GR OPTIONAL SIZES


1in 1GR 112in 1.5GR 2in 2GR 3in 3GR 4in 4GR 5in 5GR E6in 6GR F,XF8in 8GR X8GR

LIGHT DUTY SERIES

L14in X14GR L16in X16GR L18in X18GR L20in X20GR L24in X24GR

HEAVY DUTY SERIES

H2in BH3in CH4in DH8in G XGH10in 10H X10HH12in 12M X12MH14in P 5PH16in SH18inH20in UH22in V 3V H24in W 3W H26in Y 3Y

Techlok designationuses in to denotenominal size in inchesas opposed to GRwhich denotes

comparable products.


9/30

9

Techlok sealrings are available in the

following standard materials:

A1S1 4140, 630SS (17-4PH), Alloy

718, and Super Duplex. Our standard

coating is PTFE, however, other suitable

coatings are available on request, and

these coatings provide lubrication duringmake up.

Sealrings manufactured of materials or

with coatings other than PTFE are also

available to meet specific service

conditions.

For applications greater than 750F,

consult Vector International for advice

on materials and coatings.

All Techlok sealrings meet the hardnessrequirements of NACE MR-01-75.

For ease of identification Techlok PTFE

sealrings are colour coded.

i.e. blue - Carbon Steel

green - Stainless Steel

black - Alloy 718/Super Duplex

A182F55

4 R12004 R22004 R32004 R42004 1.000 25.4 0.500 12.7 0.125 3.2 0.375 9.5 0.03 0.01

5 R12005 R22005 R32005 R42005 1.094 27.8 0.625 15.9 0.125 3.2 0.375 9.5 0.03 0.01

7 R12007 R22007 R32007 R42007 1.375 34.9 0.906 23 0.125 3.2 0.375 9.5 0.04 0.02

11 R12011 R22011 R32011 R42011 1.750 44.5 1.125 28.6 0.125 3.2 0.375 9.5 0.06 0.03

13 R12013 R22013 R32013 R42013 2.375 60.3 1.500 38.1 0.125 3.2 0.375 9.5 0.11 0.05

14 R12014 R22014 R32014 R42014 2.625 66.7 1.609 40.9 0.250 6.4 0.563 14.3 0.28 0.13

16 R12016 R22016 R32016 R42016 2.750 69.9 1.868 47.4 0.250 6.4 0.625 15.9 0.28 0.13

20 R12020 R22020 R32020 R42020 3.250 82.6 2.063 52.4 0.250 6.4 0.750 19.1 0.45 0.223 R12023 R22023 R32023 R42023 3.500 88.9 2.375 60.3 0.250 6.4 0.750 19.1 0.48 0.22

25 R12025 R22025 R32025 R42025 4.000 102 2.672 67.9 0.250 6.4 0.750 19.1 0.62 0.28

27 R12027 R22027 R32027 R42027 4.250 108 3.063 77.8 0.250 6.4 0.750 19.1 0.62 0.28

31 R12031 R22031 R32031 R42031 4.500 114 3.250 82.6 0.250 6.4 0.750 19.1 0.69 0.31

34 R12034 R22034 R32034 R42034 5.000 127 3.688 93.7 0.250 6.4 0.750 19.1 0.80 0.36

40 R12040 R22040 R32040 R42040 5.500 140 4.063 103 0.250 6.4 1.000 25.4 1.13 0.51

42 R12042 R22042 R32042 R42042 6.375 162 4.188 106 0.250 6.4 1.000 25.4 1.68 0.76

46 R12046 R22046 R32046 R42046 6.250 159 4.750 121 0.250 6.4 1.000 25.4 1.34 0.61

52 R12052 R22052 R32052 R42052 6.625 168 5.313 135 0.250 6.4 1.000 25.4 1.33 0.6

54 R12054 R22054 R32054 R42054 6.812 173 5.500 140 0.250 6.4 1.000 25.4 1.57 0.71

56 R12056 R22056 R32056 R42056 7.500 191 5.750 146 0.250 6.4 1.000 25.4 1.82 0.83

62 R12062 R22062 R32062 R42062 7.875 200 6.065 154 0.375 9.5 1.375 34.9 3.13 1.42

64 R12064 R22064 R32064 R42064 8.625 219 6.500 165 0.375 9.5 1.375 34.9 3.80 1.72

67 R12067 R22067 R32067 R42067 8.750 222 6.875 175 0.375 9.5 1.375 34.9 3.61 1.64

72 R12072 R22072 R32072 R42072 9.500 241 7.250 184 0.375 9.5 1.375 34.9 4.40 2

76 R12076 R22076 R32076 R42076 10.000 254 7.750 197 0.375 9.5 1.375 34.9 4.67 2.12

82 R12082 R22082 R32082 R42082 10.125 257 8.250 210 0.375 9.5 1.375 34.9 4.26 1.93

84 R12084 R22084 R32084 R42084 11.125 283 8.500 216 0.375 9.5 1.375 34.9 5.79 2.63

87 R12087 R22087 R32087 R42087 11.375 289 8.875 225 0.375 9.5 1.375 34.9 5.77 2.62

91 R12091 R22091 R32091 R42091 11.500 292 9.125 232 0.375 9.5 1.375 34.9 5.66 2.57

92 R12092 R22092 R32092 R42092 11.625 295 9.250 235 0.375 9.5 1.375 34.9 5.78 2.62

94 R12094 R22094 R32094 R42094 11.750 298 9.500 241 0.375 9.5 1.375 34.9 5.61 2.54

97 R12097 R22097 R32097 R42097 12.000 305 9.875 251 0.375 9.5 1.375 34.9 5.55 2.52

102 R12102 R22102 R32102 R42102 12.250 311 10.250 260 0.375 9.5 1.375 34.9 5.48 2.49

106 R12106 R22106 R32106 R42106 12.750 324 10.750 273 0.375 9.5 1.375 34.9 5.72 2.59

112 R12112 R22112 R32112 R42112 14.125 359 11.250 286 0.625 15.9 1.625 41.3 12.30 5.59

116 R12116 R22116 R32116 R42116 14.125 359 11.750 298 0.375 9.5 1.375 34.9 7.21 3.27

120 R12120 R22120 R32120 R42120 13.875 352 12.000 305 0.375 9.5 1.375 34.9 6.04 2.74

122 R12122 R22122 R32122 R42122 14.125 359 12.250 311 0.375 9.5 1.375 34.9 6.16 2.79

124 R12124 R22124 R32124 R42124 14.625 371 12.500 318 0.375 9.5 1.375 34.9 7.10 3.22

130 R12130 R22130 R32130 R42130 15.000 381 13.000 330 0.500 12.7 1.500 38.1 8.47 3.84

134 R12134 R22134 R32134 R42134 15.500 394 13.500 343 0.500 12.7 1.500 38.1 8.78 3.98

137 R12137 R22137 R32137 R42137 16.500 419 13.875 352 0.625 15.9 1.625 41.3 13.70 6.21

140 R12140 R22140 R32140 R42140 16.500 419 14.000 356 0.500 12.7 1.500 38.1 10.98 4.98

144 R12144 R22144 R32144 R42144 17.000 432 14.500 368 0.500 12.7 1.500 38.1 11.35 5.15

152 R12152 R22152 R32152 R42152 17.750 451 15.250 387 0.500 12.7 1.500 38.1 11.89 5.39

160 R12160 R22160 R32160 R42160 18.500 470 16.000 406 0.500 12.7 1.500 38.1 12.44 5.64170 R12170 R22170 R32170 R42170 19.438 494 17.000 432 0.500 12.7 1.750 44.5 13.84 6.28

180 R12180 R22180 R32180 R42180 20.500 521 18.000 457 0.500 12.7 1.750 44.5 14.61 6.63

185 R12185 R22185 R32185 R42185 21.250 540 18.625 473 0.500 12.7 1.750 44.5 16.37 7.43

192 R12192 R22192 R32192 R42192 22.000 559 19.250 489 0.500 12.7 1.750 44.5 17.16 7.78

200 R12200 R22200 R32200 R42200 22.750 578 20.000 508 0.500 12.7 1.750 44.5 17.80 8.07

210 R12210 R22210 R32210 R42210 24.000 610 21.000 533 0.500 12.7 2.000 50.8 21.36 9.69

220 R12220 R22220 R32220 R42220 25.000 635 22.000 559 0.500 12.7 2.000 50.8 22.32 10.1

225 R12225 R22225 R32225 R42225 25.750 654 22.625 575 0.500 12.7 2.000 50.8 24.19 10.97

232 R12232 R22232 R32232 R42232 26.375 670 23.250 591 0.500 12.7 2.000 50.8 24.29 11.02

240 R12240 R22240 R32240 R42240 27.500 699 24.000 610 0.500 12.7 2.000 50.8 27.42 12.4

244 R12244 R22244 R32244 R42244 27.750 705 24.500 622 0.500 12.7 2.000 50.8 26.34 11.9

254 R12254 R22254 R32254 R42254 28.875 733 25.500 648 0.500 12.7 2.000 50.8 28.20 12.8

264 R12264 R22264 R32264 R42264 30.000 762 26.500 673 0.500 12.7 2.000 50.8 30.12 13.7

274 R12274 R22274 R32274 R42274 31.125 791 27.500 699 0.500 12.7 2.000 50.8 32.31 14.7

284 R12284 R22284 R32284 R42284 32.250 819 28.500 724 0.500 12.7 2.000 50.8 34.36 15.6

292 R12292 R22292 R32292 R42292 32.250 819 29.250 743 0.500 12.7 2.000 50.8 29.30 13.3

Sealrings

PRODUCT CODE NUMBERS Outside Diameter(A)

ins (mm)

Inside Diameter(B)

ins (mm)

SealringSize

Rib Thickness(C)

ins (mm)

Overall Thickness(D)

ins (mm)

SealringWeight

Lbs. (Kg)AISI 4140PTFE Ctd

630 SS

PTFE Ctd

Alloy 718

PTFE CtdSuper Duplex A182 F55(UNS 32760) PTFE Ctd

C D

B

A


10/30


11/30


12/30


13/30


14/30


15/30

15

Piping Hub Sealring Material/Coating Clamp Material Service Requirements

Material Material inc. Bolting

A106 Gr B A 105 AISI 4140 / PTFE AISI 4140 - B7/2H General Service, NACE (1)

A333 Gr 1 A 350 LF2 (Mod) (5) AISI 4140 - L7/7 General Service, NACE, Low Temperature (2)

API 5L X52 A 694 F52 AISI 4140 - L7M/7M General Service, Full NACE Service, Low Temperature (3)

A106 Gr B A 350 LF2 (Mod) - with B637 UNS N07718 / PTFE AISI 4140 - B7/2H General Service, NACE (1)

A333 Gr 1 Alloy 625 weld inlay (Alloy 718) AISI 4140 - L7/7 General Service, NACE, Low Temperature (2)

API 5L X52 on seat area A182 F55 (UNS 32760) PTFE AISI 4140 - L7M/7M General Service, Full NACE Service, Low Temperature (3)

AISI 4130 AISI 4130 AISI 4140 / PTFE AISI 4140 - B7/2H General Service, NACE (1)

AISI 4140 - L7/7 General Ser vice, NACE, Low Temperature (2)

AISI 4140 - L7M/7M General Service, Full NACE Service, Low Temperature (3)

A 312 304 SS A 182 F304A 564 - 630 (17-4 PH) / PTFE AISI 4140 - B7/2H General Service, NACE (1)

A 312 316 SS A 182 F316 (L)A182 F55 (UNS 32760) PTFE AISI 4140 - L7/7 External Corrosion, Cr yogenic Ser vice.

A 312 321 SS A 182 F321A564 630 SS (17-4 PH) / MoS2 AISI 4140 - L7M/7M External Corrosion, High Temperature Service (4)

A182 F55 (UNS 32760) MoS2

A 790 UNS S31803 A 182 F 51 A564 630 SS (17-4 PH) / PTFE AISI 4140 - B7/2H General Service, NACE (1)(Duplex) (UNS S31803) A182 F55 (UNS 32760) PTFE AISI 4140 - L7/7 General Service, NACE, Low Temperature (2)

AISI 4140 - L7M/7M General Service, Full NACE Service, Low Temperature (3)

Nickel Alloys Nickel Alloy to B637 UNS N07718 / PTFE AISI 4140 - B7/2H General Service, NACE (1)

suit piping (Alloy 718) A 182 F304 - B8/8 External Corrosion,Cryogenic Service.

B637 UNS N07718 / MoS2 A 182 F304 - B8/8 External Corrosion, High Temperature Service (4)

(Alloy 718)

This data represents Vector International standard material specifications applicable to the Techlok product range. These materials are

usually available ex-stock.

Other material specifications are available upon request. Delivery and pricing information will be furnished at the time of enquiry.

Material Selection Table

Notes

1 All Wetted surfaces meet requirements of NACE MR-01-75

2 All Wetted surfaces meet requirements of NACE MR-01-75, Materials qualified at -46 C

3 All components meet requirements of NACE MR-01-75, Materials qualified at -46 C Minimum

4 Temperatures above 400 C.

5 Techlok standard material specification is certified for A 105, A 350 LF2 (mod) and A 694 F52.

Materials Specification & SelectionMaterial Specification Table

} }

}

}

Carbon Max. 0.22 0.33 0.04 0.03 0.03 0.43 0.08 0.43 0.07 0.03 0.08Min. --- 0.28 --- --- --- 0.38 --- 0.38 --- --- ---

Silicon Max. 0.30 0.35 1.00 1.00 1.00 0.35 1.00 0.35 1.00 1.00 0.35Min. 0.15 0.15 --- --- --- 0.15 --- 0.15 --- --- ---

Manganese Max. 1.35 0.60 2.00 2.00 1.00 1.00 2.00 1.00 1.00 1.00 0.35Min. --- 0.40 --- --- --- 0.75 --- 0.75 --- --- ---

Phosphorous Max. 0.04 0.04 0.04 0.03 0.03 0.04 0.04 0.04 0.04 0.03 0.02Min. --- --- --- --- --- --- --- --- --- --- ---

Sulphur Max. 0.04 0.04 0.03 0.02 0.01 0.04 0.03 0.04 0.03 0.01 0.02Min. --- --- --- --- --- --- --- --- --- --- ---

Nickel Max. --- --- 14.00 6.50 8.00 --- 11.00 --- 5.00 8.00 55.00Min. --- --- 10.00 4.50 6.00 --- 8.00 --- 3.00 6.00 50.00

Chromium Max. --- 1.10 18.00 23.00 26.00 1.10 20.00 1.10 17.50 26.00 21.00Min. --- 0.80 16.00 21.00 24.00 0.80 18.00 0.80 15.00 24.00 17.00

Molybdenum Max. --- 0.25 3.00 3.50 4.00 0.25 --- 0.25 --- 4.00 3.30Min. --- 0.15 2.00 2.50 3.00 0.15 --- 0.15 --- 3.00 2.80

Copper Max. --- --- --- --- 1.00 --- --- --- 5.00 1.00 0.30Min. --- --- --- --- 0.50 --- --- --- 3.00 0.50 ---

Titanium Max. --- --- --- --- --- --- --- --- --- --- 1.15Min. --- --- --- --- --- --- --- --- --- --- 0.65

Tungsten Max. --- --- --- --- 1.00 --- --- --- --- 1.00 ---Min. --- --- --- --- 0.50 --- --- --- --- 0.50 ---

Nitrogen Max. --- --- --- 0.20 0.30 --- --- --- --- 0.30 ---Min. --- --- --- 0.15 0.20 --- --- --- --- 0.20 ---

Carbon Equivalent Max. 0.42 --- --- --- --- --- --- --- --- --- ---

Tensile Strength Psi 70000 90000 75000 90000 108750 100000 75000 100000 115000 108750 130000N/mm2 483 621 517 621 750 690 517 690 793 750 897

Yield Strength Psi 52000 60000 30000 65000 79750 75000 30000 75000 75000 79750 110000N/mm2 359 414 207 448 550 517 207 517 517 550 759

Hardness (Max.) 197 BHN 235 BHN --- 28 HRC 200-270 BHN 22 HRC --- 22 HRC 33 HRC 200-270 BHN 40 HRCImpact Values Joules 54/40 40/32 --- 70/65 60/45 42/32 --- 27/20 27/20 60/45 --

@ Deg C -46 -46 --- -50 -50 -46 --- -46 -46 -50 --Heat Treatment Q + T Q + T S.A. S.A. S.A. Q + T S.A. Q + T H1150(M) S.A. S.A. + P.H.Temper Temp. Deg C 650 650 --- --- --- 620 --- --- --- --- ---Corrosion Test --- --- --- G48 --- --- --- --- --- --- ---

ElementClamps

AISI 4140 A182F304

%

Butt Weld HubsDuplex Super Duplex

A350 AISI 4130 A182 A182 F51 A182 F55LF2 Mod F316(L) (UNS S31803) (UNS S32760)

SealringsSuper Duplex

AISI 4140 A564 630 A182 F55 Alloy 718(17-4 PH) (UNS S32760)


16/30

16

Quality Assurance

Vector International has successfully

been audited and awarded the

prestigious BS EN ISO 9001 - 1994

accreditation for its thorough Quality

Assurance Programme.

This ensures strict compliance with all

relevant Regulatory Specifications and

codes including ANSI, API, ASME, BS,

NACE. Material specifications to ASTM

and BS are adhered to, and full

traceability of all components is

assured.

Using the latest CNC machine tools in a

modern factory environment,

manufacture can also be carried out inaccordance with the requirements of

NS5801 and API spec Q.

Vectors in-house inspection department

completes the quality aspect of our

product by inspecting 100 percent of

manufactured parts.

Techlok connectors, in addition to

meeting the current Industry Standard

for Interchangeability, can be supplied

in accordance with various design

codes/regulations including:

ANSI/ASME

API

BS 5500

UK Offshore Regulations

Customers' special requirements

Country Codes

Type Approval TestingThe Techlok range of connectors has

been subjected to extensive strain gauge

and destructive testing under

independent conditions both in-house

and at the National Engineering

Laboratory in the UK.

Combined pressure and external load

type testing has resulted in Type

Approval being awarded by Bureau

Veritas for the Techlok product range.

Quality, Type Approval & Testing


17/30

17

External Loading

Tension

The Techlok connector is capable of

withstanding higher tensile loads than a

conventional ANSI flange. Tensile loadscan cause conventional flange faces to

separate, providing a leak path across

the flange face. With the pressure

energised bore seal, this does not occur

and the Techlok connector will remain

leak tight.

Techlok

API Fire Testing

The need for correct analysis of

product performance is a

prerequisite when specifying pipe

connectors.

Having successfully completed

strain gauge testing under full load

conditions and fire testing to API

6FB parts 1 and 2, the Techlok

range of clamp connectors suits

most applications.

Independent testing and

witnessing, resulting in Bureau

Veritas, Type Approval coupled with

extensive Finite Element Analysis

Bending

Techlok connectors are designed to

withstand severe bending loads without

leaking or loosening.Independent tests evaluating Techlok

clamp connectors have shown that even

under severe pressure and bending

conditions, the connector does not leak

and the bolting remains tight.

Increasing the bending movement to

ultimate failure of the pipe has not

resulted in connector leakage.

Techlok

Compression

Because in most cases the bearing area

of the seal ring rib is larger than the

cross section of the adjoining pipe itbecomes impossible to over compress

the Sealring within the Techlok

connector. For normal piping

applications, the compressive limits are

governed by other factors such as

piping flexibility analysis or anchor loads

and in practice the Techlok connector

will always out perform the applied

compressive loading.

Techlok

Thermal Shock

Techlok connectors have been applied

to both Cryogenic and high temperature

service which are subject to thermal

transient conditions.

For very severe thermal shock (i.e.quenching), the connectors can be

provided with thermal shrouds to

protect the Sealring lips from the full

effects of the thermal shock.

Techlok technical department should be

consulted for recommendations in such

instances.

during the fire test programme, affords

clients one of the most comprehensively

tested clamp connector available.


18/30

18

All fittings are available in a selection of

materials such as carbon, low alloy,stainless and Duplex steels, with a full

range of nickel alloys for more

specialised applications.

We also offer an individual design

service for special applications. Contact

your nearest Vector International

distributor for more details.

Dur-O-Seal

Dur-O-Seal is an alternative sealing

mechanism to the standard metal-to-metal Techlok sealring.

It is used to advantage where seats are

badly corroded or damaged, or in sandy

conditions on service/vessel closures/pig

launchers where repeated make-breaks

are required.

Dur-O-Seal is fully interchangeable with

all clamp connectors. It utilises

standard, easily replaceable 'O' rings,

and eliminates the need for costly down

time for weld repair or on-site

machining of damaged hubs.

Dur-O-Seal has a zero extrusion gap

which allows for high pressure capacity,

and there is no loss of connector

performance.

This product is not intended for

permanent installations where 'O' ring

seals are not to be used due to

operating conditions.

The Techlok Product RangeTechlok connectors are highly versatile and can be used in many

diverse applications. In addition there are several other products

completing the Techlok range, some of which are illustrated below.

Mono-Bloc Bolt Tensioner

This product combines two bolt

tensioning heads within a single block

tensioner body, enabling two adjacent

bolts to be tensioned simultaneously or,

using two Mono-Bloc tensioners, to

tension all four bolts.

The Mono-Bloc tensioner utilises

standard nuts, does not require costly

tensioner support washers, and allows forthe degree of misalignment which occurs

with clamp sets during assembly.

It ensures uniform tension with a

minimum of passes (maximum three with

a single unit), requires one-side only

access, a minimum of hose connections,

and ensures a higher quality assembly.

Particularly suitable for larger clamp sizes

and sub-sea assembly, this product is

available either for hire or purchase, or

as part of a project scope of supply.

Blind Seal Rings

Techlok blind seal rings are an effective

way of blanking off pipe runs and can

normally take full line pressure.

They can also be supplied with the Duro-

seal option utilising 'O' ring elements.

Note, Techlok Blind Sealrings are

designed as an auxiliary pressure

isolation device and therefore should be

used in conjunction with other

equipment, ie valves.

Orifice Connectors

The Techlok Orifice Connector is amatched hub pair with orifice seal ring

and clampset, and can be supplied for

all pipe sizes and materials.

The two hubs are accurately drilled and

are provided with suitable outlet

connections for accurate flow

measurement. Alternatively, special

metering spools can be utilised,

employing a separate orifice plate and

integral pressure tappings - the spool is

simply connected into the pipe run using

streamline bore Techlok connectors.

Weld Overlay

Vector International can furnish carbon

and low alloy steel hubs with corrosion

resistant weld overlay to prolong hub

life in corrosive environments such as

water injection lines.

The weld overlay is applied in Alloy

625 to the critical seat area or, if

needed, through the hub bore.

Weld overlayed hubs should be used in

conjunction with suitable sealring

materials ie 630 SS or Alloy 718.


19/30

19

Elbows and Tees

Vector can supply a range of elbows,

tees and cross pieces for use with

Techlok connectors which can facilitate

more compact pipework layouts.

These components are manufactured

from forged steel and are reinforced at

the bend section.

Weld-O-Hubs

The Techlok Weld-O-Hubs enables

pipework branch connections to be

made with a single weld, and provides

full reinforcement for the pipe run

integral with the Techlok hub.

Weld-O-Hubs are available in all

materials to suit piping requirements, in

the standard size range 1 in to 6 in.

Streamline Bore

The streamline bore seat profile is gives

a smooth bore throughout the connector

joint, minimising flow turbulance and

erosion. Alternatively, the Sealring can

be fully shrouded for severely erosive

conditions.

It is available on all Techlok hubs, is

fully compatible with the standard range

of Techlok sealrings (refer to page 9),

and is interchangeable with standard

seat profiles.

API Hubs

As a further development of our clamp

connector products, Vector International

can supply the full range of API 17D

hub components and swivel ring flange

connections.

Cross-Over Spools

Cross-Over Spools are a compact meansof joining one type of pipe connection to

another, or different pipe sizes together.

Manufactured from single-piece

forgings, they are available for a variety

of connector combinations such as:

Techlok Hub to Techlok Hub

Techlok Hub to API flange/ANSI

flange

Techlok Hub to Threaded Union

Special Spools

Studded Vessel Closures

The Techlok sealing concept reduces the

size, weight and complexity of vessel

closures. Vessel closures can be

designed and supplied studded, flanged

or clamped for all vessel sizes and formost operating conditions.

Design criteria would normally be in

accordance with ASME Pressure Vessel

Codes, BS 5500 or special customer

requirements.

Vectors experience in design and

manufacture of studded and other

vessel closures extends up to two

metres in diameter and to pressures in

excess of 10,000psi. The product range

extends to include specialised designs

for valve bonnets, offering valve

manufacturers weight reduction and

reliable high pressure sealing.

Techlok closures are available in all

common grades of pressure vessel steel

forgings, with corrosion resistant liners

and protective weld overlays.

Techlok Dual Torque Tool

The Techlok Dual Torque Tool ensures

rapid and controlled bolting of medium

sized connectors (6 in to 12 in) by

torqeuing adjacent bolts in unison to

achieve much greater accuracy of bolttension.

This product is available for hire,

complete with air pressure regulator (80

psi maximum).


20/30


21/30


22/30

22

STANDARD SERIES

HUB MATERIAL: ASTM A 182 F316 (Note 1) CLAMP MATERIAL: LOW ALLOY STEEL (Note 1)

NOM.SIZE

TECHLOKSIZE CODE

PRESSURE RATING (psi)100F 200F 300F 400F 500F 600F 700F

PRESSURE RATING (BAR)50C 100C 150C 200C 250C 300C 350C

1 in 1in 4 12003 10363 9362 8562 8001 7562 7242 803 706 646 595 559 530 5241in 5 11156 9631 8702 7958 7437 7028 6731 746 656 600 553 519 493 487

1in 7 8428 7276 6574 6012 5618 5310 5085 564 496 453 418 392 372 3681in 11 4929 4255 3845 3516 3286 3105 2974 330 290 265 244 229 218 215

1.5 in 1.5in 11 10471 9040 8167 7469 6980 6597 6318 700 616 563 519 487 462 4571.5in 13 7820 6751 6100 5578 5213 4927 4718 523 460 421 388 364 345 341

1.5in 14 6721 5803 5242 4794 4480 4234 4055 450 395 361 333 313 297 294

2 in 2in 13 9825 8482 7664 7009 6550 6190 5928 657 578 528 487 457 434 4292in 14 9271 8004 7231 6613 6180 5841 5594 620 546 499 459 432 409 405

2in 16 7374 6366 5752 5260 4916 4646 4449 493 434 397 365 343 326 3222in 20 5373 4639 4191 3833 3582 3385 3242 359 316 289 266 250 237 235

3 in 3in 20 9912 8557 7731 7071 6607 6245 5980 663 583 533 491 461 438 433

3in 23 8729 7536 6809 6227 5819 5499 5267 584 514 469 433 406 385 3813in 25 6481 5595 5055 4623 4320 4083 3910 433 381 349 321 302 286 283

3in 27 3940 3402 3073 2811 2626 2482 2377 264 232 212 195 183 174 172

3in 31 1979 1709 1544 1412 1319 1247 1194 132 116 106 98 92 87 864 in 4in 25 9647 8329 7525 6882 6431 6078 5820 645 568 519 478 449 426 421

4in 27 8015 6920 6252 5717 5343 5050 4836 536 472 431 397 373 354 3504in 31 6898 5955 5380 4921 4598 4346 4162 461 406 371 342 321 305 301

4in 34 4531 3912 3534 3232 3020 2855 2734 303 267 244 225 211 200 198

4in 40 2596 2241 2025 1852 1731 1636 1566 174 153 140 129 121 115 1135 in 5in 31 10125 8741 7898 7223 6749 6379 6109 677 596 545 502 471 447 442

5in 34 9155 7904 7141 6530 6103 5768 5523 612 539 492 454 426 404 400

5in 40 7728 6672 6028 5513 5152 4869 4663 517 455 416 383 360 341 3375in 42 7022 6062 5477 5009 4681 4424 4237 470 413 378 348 327 310 307

5in 46 4842 4180 3777 3454 3228 3051 2921 324 285 260 240 225 214 2115in 52 2652 2290 2069 1892 1768 1671 1600 177 156 143 131 123 117 116

6 in 6in 40 9790 8452 7636 6984 6526 6168 5907 655 576 527 485 456 432 428

6in 42 9440 8150 7363 6734 6293 5947 5696 631 555 508 468 439 417 4126in 46 8099 6992 6317 5777 5399 5102 4886 542 477 436 401 377 358 354

6in 52 5989 5171 4671 4272 3992 3773 3613 401 352 322 297 279 264 2626in 56 4487 3874 3500 3201 2991 2827 2707 300 264 241 222 209 198 196

6in 62 3026 2612 2360 2159 2017 1906 1826 202 178 163 150 141 134 132

8 in 8in 62 7862 6788 6132 5608 5241 4953 4743 526 463 423 390 366 347 3438in 67 5570 4809 4345 3973 3713 3509 3361 373 328 300 276 259 246 243

8in 72 4496 3882 3507 3207 2997 2833 2713 301 265 242 223 209 199 196

8in 76 3198 2761 2494 2281 2132 2015 1930 214 188 172 159 149 141 1408in 82 2147 1854 1675 1532 1431 1353 1295 144 126 116 106 100 95 94

NOM.SIZE

TECHLOKSIZE CODE



LIGHT DUTY SERIESHUB MATERIAL: ASTM A 182 F316 (Note 1) CLAMP MATERIAL: LOW ALLOY STEEL (Note 1)

14in. L14in112 4334 3742 3380 3092 2889 2730 2615 290 255 233 215 202 191 189L14in116 3969 3426 3095 2831 2645 2500 2394 265 234 213 197 185 175 173

L14in120 3738 3227 2916 2667 2492 2355 2255 250 220 201 185 174 165 163

L14in124 2869 2477 2238 2047 1913 1808 1731 192 169 154 142 134 127 125L14in130 2220 1916 1731 1583 1480 1398 1339 148 131 119 110 103 98 97

L14in134 1632 1409 1273 1164 1088 1028 985 109 96 88 81 76 72 7116in. L16in130 3416 2949 2665 2437 2277 2152 2061 228 201 184 169 159 151 149

L16in134 3174 2741 2476 2264 2116 2000 1915 212 187 171 157 148 140 139

L16in137 3010 2598 2348 2147 2006 1896 1816 201 177 162 149 140 133 131L16in140 2958 2554 2307 2110 1972 1864 1785 198 174 159 147 138 131 129

L16in144 2678 2312 2089 1911 1785 1687 1616 179 158 144 133 125 118 117

L16in152 1843 1591 1438 1315 1229 1161 1112 123 108 99 91 86 81 8018in L18in144 3202 2765 2498 2284 2135 2017 1932 214 188 172 159 149 141 140

L18in152 2902 2506 2264 2070 1935 1829 1751 194 171 156 144 135 128 127L18in160 2643 2282 2061 1885 1762 1665 1595 177 156 142 131 123 117 115

L18in170 2006 1732 1565 1431 1337 1264 1210 134 118 108 99 93 89 88

20in L20in160 2914 2516 2273 2079 1943 1836 1758 195 171 157 144 136 129 127L20in170 2586 2232 2017 1844 1724 1629 1560 173 152 139 128 120 114 113

L20in180 2313 1997 1804 1650 1542 1457 1396 155 136 124 115 108 102 101

L20in185 2149 1856 1676 1533 1433 1354 1297 144 126 116 107 100 95 94L20in192 2028 1751 1582 1447 1352 1278 1224 136 119 109 101 94 90 89

24in. L24in200 3021 2609 2357 2155 2014 1904 1823 202 178 163 150 141 133 132L24in210 2743 2368 2140 1957 1829 1728 1655 184 161 148 136 128 121 120

L24in220 2505 2162 1954 1787 1670 1578 1511 168 147 135 124 117 111 109

L24in225 2357 2035 1839 1681 1571 1485 1422 158 139 127 117 110 104 103

Pressure Temperature Ratings - Stainless Steel


23/30

2 in H2in 13 11340 9790 8845 8089 7559 7144 6842 758 667 610 562 528 501 495H2in 14 11021 9514 8596 7861 7346 6943 6649 737 648 593 546 513 487 481H2in 16 10149 8762 7917 7240 6766 6394 6123 679 597 546 503 472 448 443H2in 20 9416 8129 7344 6717 6277 5932 5681 630 554 506 467 438 416 411

3 in H3in 20 10665 9208 8319 7608 7109 6719 6435 713 628 574 528 496 471 466H3in 23 9739 8408 7596 6947 6492 6136 5876 651 573 524 483 453 430 425H3in 25 8744 7549 6820 6237 5829 5508 5275 585 514 470 433 407 386 382

H3in 27 6494 5607 5066 4633 4329 4092 3918 434 382 349 322 302 287 2844 in H4in 25 10587 9140 8258 7552 7057 6670 6387 708 623 569 525 493 467 462

H4in 27 9671 8350 7544 6899 6447 6093 5835 647 569 520 479 450 427 422H4in 31 9187 7932 7166 6554 6124 5788 5543 614 541 494 455 428 406 401H4in 34 7421 6406 5788 5293 4947 4675 4477 496 437 399 368 345 328 324H4in 40 5504 4751 4293 3926 3669 3467 3320 368 324 296 273 256 243 240

8 in H8in 52 9279 8011 7238 6619 6186 5846 5598 621 546 499 460 432 410 405

H8in 56 8555 7385 6673 6102 5703 5389 5161 572 503 460 424 398 378 374H8in 62 7214 6228 5627 5146 4809 4545 4353 483 425 388 358 336 319 315H8in 64 5936 5125 4630 4235 3957 3740 3582 397 349 319 294 276 262 259H8in 67 4928 4254 3844 3515 3285 3104 2973 330 290 265 244 229 218 215H8in 72 3844 3319 2998 2742 2562 2422 2319 257 226 207 191 179 170 168

10 in H10in 82 5499 4748 4289 3923 3666 3464 3318 368 324 296 273 256 243 240H10in 84 4956 4279 3866 3535 3304 3122 2990 331 292 267 246 231 219 216H10in 87 4094 3535 3193 2920 2729 2579 2470 274 241 220 203 191 181 179

H10in 94 2793 2411 2179 1992 1862 1760 1685 187 164 150 138 130 123 122H10in 97 2142 1849 1671 1528 1428 1350 1292 143 126 115 106 100 95 94H10in 102 1578 1362 1231 1126 1052 994 952 106 93 85 78 73 70 69

12 in H12in 97 5655 4882 4411 4034 3770 3563 3412 378 333 304 280 263 250 247H12in 102 4971 4292 3877 3546 3314 3132 2999 332 293 267 246 231 219 217H12in 106 4019 3470 3135 2867 2679 2532 2425 269 237 216 199 187 177 176H12in 112 3124 2697 2437 2229 2083 1968 1885 209 184 168 155 145 138 136

H12in 120 2007 1733 1566 1432 1338 1264 1211 134 118 108 99 93 89 8814 in H14in 106 6995 6039 5456 4989 4663 4407 4220 468 412 376 347 326 309 305


H14in 134 2599 2244 2027 1854 1732 1637 1568 174 153 140 129 121 115 11416 in H16in 112 8767 7569 6838 6254 5844 5523 5289 586 516 472 434 408 387 383


H16in 144 4287 3701 3344 3058 2858 2701 2586 287 252 231 212 200 189 187H16in 152 3258 2813 2541 2324 2172 2053 1966 218 192 175 161 152 144 14218 in H18in 140 5904 5097 4605 4211 3936 3719 3562 395 347 318 293 275 261 258

H18in 144 5250 4532 4095 3745 3500 3307 3167 351 309 282 260 244 232 229H18in 152 4285 3700 3343 3057 2857 2700 2585 287 252 231 212 199 189 187H18in 160 3300 2849 2574 2354 2200 2079 1991 221 194 177 164 154 146 144H18in 170 2193 1894 1711 1565 1462 1382 1323 147 129 118 109 102 97 96

20 in H20in 152 6716 5932 5359 4901 4580 4329 4145 451 404 370 340 320 303 300

H20in 160 5967 5152 4654 4257 3978 3759 3600 399 351 321 296 278 263 261H20in 170 4838 4176 3773 3451 3225 3048 2919 324 285 260 240 225 214 211H20in 180 3666 3165 2859 2615 2444 2309 2212 245 216 197 182 171 162 160H20in185 2976 2569 2321 2123 1984 1875 1795 199 175 160 147 139 131 130H20in 192 2400 2072 1872 1712 1600 1512 1448 161 141 129 119 112 106 105

22 in H22in 160 5433 4691 4238 3876 3622 3423 3278 363 320 292 269 253 240 237H22in 170 4822 4163 3761 3440 3215 3038 2909 323 284 259 239 224 213 211H22in 180 4312 3723 3363 3076 2874 2717 2602 288 254 232 214 201 190 188

H22in 185 3594 3103 2803 2564 2396 2264 2168 240 211 193 178 167 159 157H22in 192 2984 2576 2327 2128 1989 1880 1800 200 176 160 148 139 132 130H22in 200 2303 1988 1796 1643 1535 1451 1390 154 136 124 114 107 102 101H22in 210 1521 1313 1186 1085 1014 958 918 102 89 82 75 71 67 66

24 in H24in 192 4334 3741 3380 3091 2889 2730 2615 290 255 233 215 202 191 189H24in 200 4020 3471 3136 2868 2680 2533 2426 269 237 216 199 187 178 176

H24in 210 3650 3152 2847 2604 2433 2300 2202 244 215 196 181 170 161 159H24in 220 3058 2640 2385 2182 2039 1927 1845 205 180 165 152 142 135 134H24in 225 2948 2545 2299 2103 1965 1857 1778 197 173 159 146 137 130 129H24in 232 2078 1794 1621 1482 1385 1309 1254 139 122 112 103 97 92 91

26 in H26in 225 3387 3334 3012 2755 2574 2433 2330 233 227 208 191 180 171 169H26in 232 3229 2880 2602 2380 2224 2102 2013 217 196 179 165 155 147 146H26in 240 2733 2360 2132 1950 1822 1722 1649 183 161 147 135 127 121 119H26in 244 2364 2041 1844 1687 1576 1490 1427 158 139 127 117 110 104 103

H26in 254 1698 1466 1325 1212 1132 1070 1025 114 100 91 84 79 75 74H26in 264 1120 967 873 799 746 705 675 75 66 60 55 52 49 49H26in 270 863 745 673 616 575 544 521 58 51 46 43 40 38 38

23

HEAVY DUTY SERIES

HUB MATERIAL: ASTM A 182 F316 (Note 1) CLAMP MATERIAL: LOW ALLOY STEEL (Note 1)

NOM.SIZE

TECHLOKSIZE CODE



Notes

1 See material specification tables page 15 for full details.2 Corrosion allowance = Zero.3 Max. Hydrostatic test pressure = 1.5 x Rated Pressure.4 Pressure ratings are based upon the hub bore being equal to the sealring bore.


24/30

LIGHT DUTY SERIESHUB MATERIAL: ASTM A 182 F51 or UNS S31803 (Note 1) CLAMP MATERIAL: LOW ALLOY STEEL (Note 1)

NOM.SIZE

TECHLOKSIZE CODE

PRESSURE RATING (psi)70F 100F 150F 200F 250F 300F 350F 400F

PRESSURE RATING (BAR)20C 50C 100C 150C 200C

14in. L14in112 4949 4949 4949 4949 4949 4949 4949 4949 341 341 341 341 341

L14in116 4531 4531 4531 4531 4531 4531 4531 4531 312 312 312 312 312

L14in120 4367 4367 4367 4367 4367 4367 4367 4367 301 301 301 301 301L14in124 3996 3996 3996 3996 3996 3996 3996 3996 276 276 276 276 276

L14in130 3740 3740 3679 3535 3432 3329 3268 3206 258 256 242 230 222L14in134 2981 2849 2706 2600 2524 2449 2403 2358 206 192 178 169 163

16in. L16in130 4198 4198 4198 4198 4198 4198 4198 4198 289 289 289 289 289

L16in134 3902 3902 3902 3902 3902 3902 3902 3902 269 269 269 269 269L16in137 3700 3700 3700 3700 3700 3700 3700 3700 255 255 255 255 255

L16in140 3636 3636 3636 3636 3636 3636 3636 3636 251 251 251 251 251L16in144 3396 3396 3396 3396 3396 3396 3396 3396 234 234 234 234 234

L16in152 3078 3078 3055 2936 2850 2765 2714 2663 212 212 201 191 184

18in L18in144 3472 3472 3472 3472 3472 3472 3472 3472 239 239 239 239 239

L18in152 3147 3147 3147 3147 3147 3147 3147 3147 217 217 217 217 217L18in160 2866 2866 2866 2866 2866 2866 2866 2866 198 198 198 198 198

L18in170 2543 2543 2543 2543 2543 2543 2543 2543 175 175 175 175 17520in L20in160 3866 3866 3866 3866 3866 3866 3866 3866 267 267 267 267 267

L20in170 3431 3431 3431 3431 3431 3431 3431 3431 237 237 237 237 237L20in180 3069 3069 3069 3069 3069 3069 3069 3069 212 212 212 212 212

L20in185 2851 2851 2851 2851 2851 2851 2851 2851 197 197 197 197 197

L20in192 2691 2691 2691 2691 2691 2691 2691 2691 186 186 186 186 18624in. L24in200 3145 3145 3145 3145 3145 3145 3145 3145 217 217 217 217 217

L24in210 2855 2855 2855 2855 2855 2855 2855 2855 197 197 197 197 197

L24in220 2606 2606 2606 2606 2606 2606 2606 2606 180 180 180 180 180L24in225 2454 2454 2454 2454 2454 2454 2454 2454 169 169 169 169 169

24

STANDARD SERIES

HUB MATERIAL: ASTM A 182 F51 or UNS S31803 (Note 1) CLAMP MATERIAL: LOW ALLOY STEEL (Note 1)

NOM.SIZE

TECHLOKSIZE CODE



1 in 1in 4 21916 20949 19894 19115 18560 18005 17671 17338 1511 1412 1309 1241 11991in 5 20370 19471 18490 17767 17250 16734 16424 16114 1404 1313 1216 1154 1114

1in 7 15389 14710 13968 13422 13032 12642 12408 12174 1061 992 919 872 8421in 11 9000 8603 8169 7850 7622 7394 7257 7120 621 580 537 510 492

1.5 in 1.5in 11 19119 18275 17355 16676 16191 15707 15416 15125 1318 1232 1142 1083 1046

1.5in 13 14278 13649 12961 12454 12092 11730 11513 11296 984 920 853 809 7811.5in 14 12272 11730 11139 10704 10393 10082 9895 9708 846 791 733 695 671

2 in 2in 13 17939 17148 16284 15647 15192 14738 14465 14192 1237 1156 1071 1016 981

2in 14 16928 16181 15366 14765 14336 13907 13649 13391 1167 1091 1011 959 9262in 16 13464 12870 12222 11744 11402 11061 10856 10651 928 868 804 763 737

2in 20 9811 9378 8905 8557 8308 8060 7910 7761 676 632 586 556 5373 in 3in 20 18098 17300 16428 15785 15327 14868 14593 14317 1248 1166 1081 1025 990

3in 23 15938 15235 14467 13901 13497 13094 12851 12609 1099 1027 952 903 872

3in 25 11834 11312 10742 10321 10021 9722 9542 9361 816 763 707 670 6473in 27 7194 6877 6530 6275 6092 5910 5801 5691 496 464 430 407 394

3in 31 3613 3454 3280 3152 3060 2969 2914 2859 249 233 216 205 198

4 in 4in 25 17614 16837 15989 15363 14917 14471 14203 13935 1214 1135 1052 998 9644in 27 14634 13989 13284 12764 12393 12023 11800 11577 1009 943 874 829 801

4in 31 12595 12039 11433 10985 10666 10347 10155 9964 868 812 752 713 6894in 34 8273 7908 7510 7216 7006 6797 6671 6545 570 533 494 469 453

4in 40 4740 4531 4303 4134 4014 3894 3822 3750 327 305 283 268 259

5 in 5in 31 18487 17672 16781 16125 15656 15188 14906 14625 1275 1191 1104 1047 10115in 34 15033 15033 15033 14580 14156 13732 13478 13224 1037 1037 998 947 915

5in 40 12180 12180 12180 12180 11950 11592 11378 11163 840 840 836 799 7725in 42 11497 11497 11497 11183 10858 10533 10338 10143 793 793 766 726 701

5in 46 8841 8451 8025 7711 7487 7263 7129 6994 610 570 528 501 484

5in 52 4843 4629 4396 4224 4101 3979 3905 3831 334 312 289 274 2656 in 6in 40 16071 16071 16071 15591 15138 14685 14413 14141 1108 1108 1068 1013 978

6in 42 15170 15170 15170 15034 14597 14160 13898 13636 1046 1046 1029 976 943

6in 46 11923 11923 11923 11923 11923 11923 11923 11699 822 822 822 822 8096in 52 9620 9620 9620 9538 9261 8984 8817 8651 663 663 653 619 598

6in 56 8193 7831 7437 7146 6938 6731 6606 6481 565 528 489 464 4486in 62 5525 5281 5015 4819 4679 4539 4455 4371 381 356 330 313 302

8 in 8in 62 9586 9586 9586 9586 9586 9586 9586 9586 661 661 661 661 661

8in 67 7563 7563 7563 7563 7563 7563 7563 7563 521 521 521 521 5218in 72 6840 6840 6840 6840 6840 6744 6619 6494 472 472 472 465 449

8in 76 5839 5582 5300 5093 4945 4797 4708 4619 403 376 349 331 3198in 82 3920 3747 3558 3419 3320 3221 3161 3101 270 253 234 222 214

Pressure Temperature Ratings - Duplex Steel


25/30

2 in H2in 13 20706 19792 18795 18060 17535 17010 16695 16380 1428 1334 1237 1173 1133H2in 14 20122 19234 18265 17551 17041 16531 16225 15919 1387 1297 1202 1140 1101H2in 16 18531 17714 16821 16163 15694 15224 14942 14660 1278 1194 1107 1050 1014H2in 20 17192 16434 15606 14995 14559 14124 13862 13601 1185 1108 1027 974 941

3 in H3in 20 19473 18614 17676 16985 16491 15998 15701 15405 1343 1255 1163 1103 1065H3in 23 17782 16998 16141 15510 15059 14608 14338 14067 1226 1146 1062 1007 973H3in 25 15965 15260 14491 13925 13520 13115 12872 12630 1101 1029 953 904 873H3in 27 11858 11335 10764 10343 10042 9742 9561 9381 818 764 708 672 649

4 in H4in 25 19330 18477 17546 16860 16370 15880 15586 15292 1333 1246 1154 1095 1058H4in 27 17659 16880 16029 15402 14955 14507 14238 13970 1218 1138 1055 1000 966H4in 31 16775 16035 15227 14631 14206 13781 13526 13270 1157 1081 1002 950 918H4in 34 13549 12951 12299 11818 11474 11131 10925 10719 934 873 809 767 741H4in 40 10049 9605 9121 8765 8510 8255 8102 7950 693 648 600 569 550

8 in H8in 52 13946 13946 13946 13946 13946 13919 13661 13403 962 962 962 960 927H8in 56 11976 11976 11976 11976 11976 11976 11976 11976 826 826 826 826 826H8in 62 10191 10191 10191 10191 10191 10191 10191 10191 703 703 703 703 703

H8in 64 8938 8938 8938 8938 8938 8905 8740 8575 616 616 616 614 593H8in 67 8041 8041 8041 7847 7619 7391 7254 7118 554 554 537 510 492H8in 72 7019 6709 6371 6122 5944 5766 5659 5552 484 452 419 398 384

10 in H10in 82 9660 9598 9114 8758 8503 8249 8096 7943 666 647 600 569 549H10in 84 9049 8650 8214 7893 7663 7434 7296 7159 624 583 540 513 495H10in 87 7475 7145 6785 6520 6331 6141 6027 5914 515 482 446 423 409

H10in 94 5100 4875 4629 4448 4319 4190 4112 4034 352 329 305 289 279H10in 97 3911 3739 3550 3411 3312 3213 3154 3094 270 252 234 222 214H10in 102 2881 2754 2615 2513 2440 2367 2323 2279 199 186 172 163 158


14 in H14in 106 9054 9054 9054 9054 9054 9054 9054 9054 624 624 624 624 624

H14in 112 7946 7946 7946 7946 7946 7946 7946 7946 548 548 548 548 548H14in 116 7275 7275 7275 7275 7275 7275 7275 7275 502 502 502 502 502H14in 120 7014 7014 7014 7014 7014 7014 7014 7014 484 484 484 484 484H14in 124 6418 6418 6418 6418 6302 6113 6000 5887 443 443 441 421 407H14in 130 5998 5734 5445 5232 5080 4928 4837 4745 414 387 358 340 328H14in 134 4745 4536 4307 4139 4019 3898 3826 3754 327 306 283 269 260

16 in H16in 112 12899 12899 12899 12899 12899 12899 12899 12663 889 889 889 889 876

H16in 120 11386 11386 11386 11386 11386 11386 11386 11386 785 785 785 785 785H16in 130 9750 9750 9750 9750 9750 9520 9344 9168 672 672 672 656 634H16in 134 9061 9061 9061 8981 8720 8459 8303 8146 625 625 615 583 563H16in 137 8591 8591 8502 8170 7932 7695 7553 7410 592 590 559 531 512H16in 140 8443 8443 8228 7906 7676 7447 7309 7171 582 576 541 513 496

H16in 144 7827 7482 7105 6827 6628 6430 6311 6192 540 504 467 443 428H16in 152 5949 5686 5400 5189 5038 4887 4797 4706 410 383 355 337 325


20 in H20in 152 6716 6716 6716 6716 6716 6716 6716 6716 463 463 463 463 463H20in 160 6115 6115 6115 6115 6115 6115 6115 6115 422 422 422 422 422H20in 170 5426 5426 5426 5426 5426 5426 5426 5426 374 374 374 374 374

H20in 180 4853 4853 4853 4853 4853 4853 4853 4853 335 335 335 335 335H20in185 4510 4510 4510 4510 4510 4464 4381 4298 311 311 311 308 297H20in 192 4256 4189 3978 3823 3712 3601 3534 3467 293 282 262 248 240

22 in H22in 160 6897 6897 6897 6897 6897 6897 6897 6897 476 476 476 476 476H22in 170 6121 6121 6121 6121 6121 6121 6121 6121 422 422 422 422 422H22in 180 5473 5473 5473 5473 5473 5473 5473 5473 377 377 377 377 377H22in 185 5087 5087 5087 5087 5087 5087 5087 5087 351 351 351 351 351

H22in 192 4800 4800 4800 4751 4613 4475 4392 4310 331 331 325 309 298H22in 200 4205 4020 3817 3668 3561 3455 3391 3327 290 271 251 238 230H22in 210 2777 2655 2521 2422 2352 2282 2239 2197 191 179 166 157 152

24 in H24in 192 4965 4965 4965 4965 4965 4965 4965 4965 342 342 342 342 342H24in 200 4607 4607 4607 4607 4607 4607 4607 4607 318 318 318 318 318

H24in 210 4183 4183 4183 4183 4183 4183 4183 4183 288 288 288 288 288H24in 220 3818 3818 3818 3818 3818 3818 3818 3818 263 263 263 263 263

H24in 225 3594 3594 3594 3594 3594 3594 3594 3594 248 248 248 248 248H24in 232 3425 3425 3425 3310 3213 3117 3059 3002 236 236 227 215 208

26 in H26in 225 3387 3387 3387 3387 3387 3387 3387 3387 234 234 234 234 234H26in 232 3229 3229 3229 3229 3229 3229 3229 3229 223 223 223 223 223H26in 240 3033 3033 3033 3033 3033 3033 3033 3033 209 209 209 209 209H26in 244 2913 2913 2913 2913 2913 2913 2913 2913 201 201 201 201 201H26in 254 2692 2692 2692 2692 2626 2548 2500 2453 186 186 185 176 170H26in 264 2044 1954 1856 1783 1731 1679 1648 1617 141 132 122 116 112

H26in 270 1576 1506 1431 1375 1335 1295 1271 1247 109 102 94 89 86

25

HEAVY DUTY SERIES

HUB MATERIAL: ASTM A 182 F51 or UNS S31803 (Note 1) CLAMP MATERIAL: LOW ALLOY STEEL (Note 1)

NOM.SIZE

TECHLOKSIZE CODE



Notes

1 See material specification tables page 15 for full details.2 Corrosion allowance = Zero.3 Max. Hydrostatic test pressure = 1.5 x Rated Pressure.4 Pressure ratings are based upon the hub bore being equal to the sealring bore.


26/30

26

Pressure Temperature Ratings - Super Duplex

LIGHT DUTY SERIES

HUB MATERIAL: UNS 32760 (Note 1) CLAMP MATERIAL: LOW ALLOY STEEL (Note 1)

NOM.SIZE

TECHLOKSIZE CODE



14in. L14in112 4948 4948 4948 4948 4948 4948 4948 4948 341 341 341 341 341L14in116 4531 4531 4531 4531 4531 4531 4531 4531 312 312 312 312 312

L14in120 4367 4367 4367 4367 4367 4367 4367 4367 301 301 301 301 301L14in124 3996 3996 3996 3996 3996 3996 3996 3996 276 276 276 276 276L14in130 3740 3740 3740 3740 3740 3740 3740 3740 258 258 258 258 258

L14in134 3292 3217 3134 3081 3029 2981 2959 2932 227 219 212 205 20216in. L16in130 4198 4198 4198 4198 4198 4198 4198 4198 289 289 289 289 289

L16in134 3902 3902 3902 3902 3902 3902 3902 3902 269 269 269 269 269L16in137 3699 3699 3699 3699 3699 3699 3699 3699 255 255 255 255 255

L16in140 3636 3636 3636 3636 3636 3636 3636 3636 251 251 251 251 251L16in144 3396 3396 3396 3396 3396 3396 3396 3396 234 234 234 234 234L16in152 3077 3077 3077 3077 3077 3077 3077 3077 212 212 212 212 212

18in L18in144 3472 3472 3472 3472 3472 3472 3472 3472 239 239 239 239 239L18in152 3147 3147 3147 3147 3147 3147 3147 3147 217 217 217 217 217

L18in160 2866 2866 2866 2866 2866 2866 2866 2866 198 198 198 198 198L18in170 2543 2543 2543 2543 2543 2543 2543 2543 175 175 175 175 175

20in L20in160 3866 3866 3866 3866 3866 3866 3866 3866 267 267 267 267 267

L20in170 3431 3431 3431 3431 3431 3431 3431 3431 237 237 237 237 237L20in180 3069 3069 3069 3069 3069 3069 3069 3069 212 212 212 212 212

L20in185 2851 2851 2851 2851 2851 2851 2851 2851 197 197 197 197 197L20in192 2691 2691 2691 2691 2691 2691 2691 2691 186 186 186 186 186

24in. L24in200 3145 3145 3145 3145 3145 3145 3145 3145 217 217 217 217 217

L24in210 2855 2855 2855 2855 2855 2855 2855 2855 197 197 197 197 197L24in220 2606 2606 2606 2606 2606 2606 2606 2606 180 180 180 180 180

L24in225 2454 2454 2454 2454 2454 2454 2454 2454 169 169 169 169 169

STANDARD SERIES


NOM.SIZE

TECHLOKSIZE CODE



1 in 1in 4 24205 23657 23044 22658 22271 21916 21755 21562 1669 1612 1556 1511 14891in 5 22497 21987 21418 21059 20699 20370 20220 20041 1551 1499 1446 1404 13841in 7 16996 16611 16181 15909 15638 15389 15276 15140 1172 1132 1092 1061 1045

1in 11 9940 9715 9463 9304 9145 9000 8934 8854 685 662 639 621 6111.5 in 1.5in 11 21115 20637 20103 19766 19428 19119 18979 18810 1456 1407 1357 1318 1299

1.5in 13 15769 15412 15014 14762 14510 14278 14174 14048 1087 1051 1014 984 9701.5in 14 13553 13246 12904 12687 12470 12272 12182 12074 934 903 871 846 834

2 in 2in 13 19813 19364 18863 18546 18230 17939 17808 17650 1366 1320 1273 1237 1219

2in 14 18695 18272 17799 17501 17202 16928 16804 16654 1289 1245 1202 1167 11502in 16 14870 14533 14157 13920 13682 13464 13365 13247 1025 991 956 928 915

2in 20 10835 10590 10316 10142 9969 9811 9739 9652 747 722 696 676 6663 in 3in 20 19988 19535 19030 18711 18391 18098 17966 17806 1378 1332 1285 1248 1229

3in 23 17603 17204 16759 16477 16196 15938 15821 15681 1214 1173 1131 1099 10833in 25 13069 12773 12443 12234 12025 11834 11747 11642 901 871 840 816 8043in 27 7945 7765 7564 7437 7310 7194 7141 7078 548 529 511 496 489

3in 31 3991 3900 3799 3736 3672 3613 3587 3555 275 266 257 249 2454 in 4in 25 19454 19013 18521 18210 17899 17614 17485 17330 1341 1296 1250 1214 1197

4in 27 16163 15797 15388 15130 14871 14634 14527 14398 1114 1077 1039 1009 9944in 31 13910 13595 13243 13021 12799 12595 12503 12391 959 927 894 868 8564in 34 9137 8930 8699 8553 8407 8273 8212 8139 630 609 587 570 562

4in 40 5235 5116 4984 4900 4817 4740 4705 4663 361 349 336 327 322

5 in 5in 31 19133 19133 19133 19113 18786 18487 18352 18188 1319 1319 1312 1275 12565in 34 15033 15033 15033 15033 15033 15033 15033 15033 1037 1037 1037 1037 10375in 40 12180 12180 12180 12180 12180 12180 12180 12180 840 840 840 840 8405in 42 11497 11497 11497 11497 11497 11497 11497 11497 793 793 793 793 793

5in 46 9036 9036 9036 9036 8984 8841 8776 8698 623 623 622 610 6015in 52 5349 5227 5092 5007 4921 4843 4807 4765 369 356 344 334 329

6 in 6in 40 16071 16071 16071 16071 16071 16071 16071 16071 1108 1108 1108 1108 11086in 42 15170 15170 15170 15170 15170 15170 15170 15170 1046 1046 1046 1046 1046

6in 46 11923 11923 11923 11923 11923 11923 11923 11923 822 822 822 822 8226in 52 9620 9620 9620 9620 9620 9620 9620 9620 663 663 663 663 6636in 56 8261 8261 8261 8261 8261 8193 8133 8060 570 570 570 565 557

6in 62 6102 5964 5810 5712 5615 5525 5485 5436 421 407 392 381 3758 in 8in 62 9586 9586 9586 9586 9586 9586 9586 9586 661 661 661 661 661

8in 67 7563 7563 7563 7563 7563 7563 7563 7563 521 521 521 521 5218in 72 6840 6840 6840 6840 6840 6840 6840 6840 472 472 472 472 4728in 76 6026 6026 6026 6026 5934 5839 5796 5745 415 415 414 403 397

8in 82 4330 4231 4122 4053 3984 3920 3891 3857 299 288 278 270 266


27/30

27

HEAVY DUTY SERIES


NOM.SIZE

TECHLOKSIZE CODE



2 in H2in 13 22868 22350 21772 21406 21041 20706 20554 20371 1577 1523 1470 1428 1407H2in 14 22223 21720 21158 20803 20448 20122 19975 19797 1532 1480 1428 1387 1367

H2in 16 20467 20003 19486 19158 18831 18531 18396 18232 1411 1363 1315 1278 1259H2in 20 18987 18557 18077 17774 17470 17192 17066 16914 1309 1265 1220 1185 1168

3 in H3in 20 21507 21020 20476 20132 19788 19473 19330 19158 1483 1433 1382 1343 1323

H3in 23 19639 19194 18698 18384 18070 17782 17652 17495 1354 1308 1262 1226 1208H3in 25 17632 17232 16787 16505 16223 15965 15848 15707 1216 1175 1133 1101 1084H3in 27 13096 12800 12469 12259 12050 11858 11771 11666 903 872 842 818 806

4 in H4in 25 21349 20865 20325 19984 19643 19330 19188 19018 1472 1422 1372 1333 1313

H4in 27 19503 19061 18568 18256 17945 17659 17529 17374 1345 1299 1254 1218 1200H4in 31 17543 17543 17543 17342 17046 16775 16652 16504 1210 1210 1191 1157 1140H4in 34 13784 13784 13784 13784 13768 13549 13450 13330 950 950 950 934 920

H4in 40 11098 10847 10566 10389 10211 10049 9975 9886 765 739 713 693 6838 in H8in 52 13946 13946 13946 13946 13946 13946 13946 13946 962 962 962 962 962

H8in 56 11976 11976 11976 11976 11976 11976 11976 11976 826 826 826 826 826

H8in 62 10191 10191 10191 10191 10191 10191 10191 10191 703 703 703 703 703H8in 64 8938 8938 8938 8938 8938 8938 8938 8938 616 616 616 616 616H8in 67 8041 8041 8041 8041 8041 8041 8041 8041 554 554 554 554 554H8in 72 7272 7272 7272 7256 7132 7019 6967 6905 501 501 498 484 477

10 in H10in 82 9660 9660 9660 9660 9660 9660 9660 9660 666 666 666 666 666H10in 84 9125 9125 9125 9125 9125 9049 8983 8903 629 629 629 624 615

H10in 87 8256 8069 7860 7728 7596 7475 7420 7354 569 550 531 515 508H10in 94 5632 5505 5362 5272 5182 5100 5062 5017 388 375 362 352 346H10in 97 4319 4222 4112 4043 3974 3911 3882 3848 298 288 278 270 266H10in 102 3182 3110 3030 2979 2928 2881 2860 2835 219 212 205 199 196

12 in H12in 97 8555 8555 8555 8555 8555 8555 8555 8555 590 590 590 590 590H12in 102 7963 7963 7963 7963 7963 7963 7963 7963 549 549 549 549 549H12in 106 7265 7265 7265 7265 7265 7265 7265 7220 501 501 501 501 498H12in 112 6300 6157 5998 5897 5796 5704 5662 5612 434 420 405 393 387

H12in 120 4047 3956 3853 3789 3724 3665 3638 3605 279 270 260 253 24914 in H14in 106 9054 9054 9054 9054 9054 9054 9054 9054 624 624 624 624 624

H14in 112 7946 7946 7946 7946 7946 7946 7946 7946 548 548 548 548 548

H14in 116 7275 7275 7275 7275 7275 7275 7275 7275 502 502 502 502 502H14in 120 7014 7014 7014 7014 7014 7014 7014 7014 484 484 484 484 484H14in 124 6418 6418 6418 6418 6418 6418 6418 6418 442 442 442 442 442

H14in 130 6006 6006 6006 6006 6006 5998 5954 5901 414 414 414 414 407H14in 134 5241 5122 4989 4906 4822 4745 4710 4668 361 349 337 327 322

16 in H16in 112 12899 12899 12899 12899 12899 12899 12899 12899 889 889 889 889 889H16in 120 11386 11386 11386 11386 11386 11386 11386 11386 785 785 785 785 785

H16in 130 9750 9750 9750 9750 9750 9750 9750 9750 672 672 672 672 672H16in 134 9061 9061 9061 9061 9061 9061 9061 9061 625 625 625 625 625H16in 137 8591 8591 8591 8591 8591 8591 8591 8591 592 592 592 592 592

H16in 140 8443 8443 8443 8443 8443 8443 8443 8443 582 582 582 582 582H16in 144 7886 7886 7886 7886 7886 7827 7770 7701 544 544 544 540 532H16in 152 6570 6421 6255 6150 6045 5949 5905 5853 453 438 422 410 404

18 in H18in 140 6793 6793 6793 6793 6793 6793 6793 6793 468 468 468 468 468H18in 144 6345 6345 6

Date post:	03-Mar-2018
Category:	Documents
Upload:	orea1
View:	380 times
Download:	13 times

Catalogo - Techlok

Documents