Caterpillar® Small and MediumSeries Wheel Loaders
924H/924Hz/928Hz/930H/938H/IT38H
950H/962H/IT62H/966H/972H/980H Series
Pocket Reference Guide 2009
2
Model Cross-Reference Chart
Cat® John Deere Komatsu Volvo Kawasaki Case
924Hz 444K/524K WA200-6 L60F — 521DPin on
924H 444K WA200-6 L60F — 521D XTHook on Powerllel WA250PZ-6
928Hz 544K WA250-6 L70F — 621E
930H 544K WA250PZ-6 L70F — 621E XTHook On Powerllel WA320PZ-6
938H 624K WA320-6 L90F 70AV-2 721E
IT38H 624K — L90F — 721E XT
950H 644K WA380-6 L110F 80ZV-2 821E
962H 724K WA430-6 L120F 85ZV-2 —
IT62H 724K — L120Fwith QC — —
966H 744K WA450-6 L150F — 921E
972H 824K WA480-6 L180F 90ZV-2 —
980H 844K WA500-6 L220F 95ZV-2 1221E
924Hz Pin-on Specification Comparisons
3
Cat Deere Deere Case Volvo Komatsu
924Hz 444K Z-Bar 524K Z-Bar 521D L60F WA200-6
Rated Net Power kW (hp) 96 (128) N/A N/A 82 (110) N/A N/Arpm 2300 N/A N/A 2000 N/A N/A
Max. Net Power kW (hp) 103 (138) 95 (128) 110 (146) 88 (118) 115 (154) 94 (126)rpm 1800 2100 2000 2000 1700 2000
Bucket Range m3 1.7-2.1 1.5-1.9 1.7-2.1 1.5-1.9 1.6-5.0 1.7-2.4(yd3) (2.2-2.7) (2.0-2.5) (2.27-2.75) (2.0-2.5) (2.1-6.5) (2.2-3.1)
Bucket used for specs m3 1.8 1.9 2.1 1.7 2.1 2.0with BOCE (yd3) (2.4) (2.5) (2.75) (2.25) (2.7) (2.6)
Operating Weight kg 10 968 11 055 12 474 10 028 11 600 10 550(lb) (24,180) (24,372) (27,500) (22,109) (25,580) (23,259)
Breakout Force kN 97.6 80.5 83.42 86.3 82.9 93.2(lb) (21,945) (18,104) (22,394) (19,392) (18,640) (20,944)
Straight Tipping Load kg 8816 9275 8750 8264 8520 9690(lb) (19,437) (20,447) (19,290) (18,219) (18,780) (21,363)
Full Turn Static Tipping Load kg 7640 8072 7572 7182 7380 8345(lb) (16,844) (17,796) (16,693) (15,833) (16,270) (18,397)
Articulation Angle degree 40 40 40 40 40 40
Wheelbase mm 2800 2760 2930 2750 3000 2840(ft in) (9'2") (9'1") (9'7") (9'0") (9'10") (9'4")
924Hz Pin-on Specification Comparisons
4
Cat Deere Deere Case Volvo Komatsu
924Hz 444K Z-Bar 524K Z-Bar 521D L60F WA200-6
Width Over Tires mm 2502 2415 2545 2308 2440 2470(ft in) (8'3") (7'11") (8'4") (7'7") (8'0") (8'1")
Dump Clearance mm 2828 2670 2770 2708 2830 2830(ft in) (9'4") (8'9") (9'1") (8'11") (9'3") (9'3")
Reach – full lift mm 791 1040 980 1013 1010 930(ft in) (2'7") (3'5") (3'2") (3'4") (3'4") (3'1")
Overall Length mm 6898 6860 7340 6643 7270 6895(ft in) (22'8") (22'6") (24'1") (21'9") (23'10") (22'7")
Loader Clearance Circle mm 11 232 11 070 11 600 10 915 11 590 11 700(ft in) (36'10") (36'4") (38'1") (35'10") (38'0") (38'5")
Hinge Pin Height mm 3757 3610 3770 3603 3870 3705fully raised (ft in) (12'4") (11'10") (12'5") (11'10") (12'9") (12'2")
Height to top of ROPS mm 3227 3170 3250 3173 3220 3180(ft in) (10'7") (10'5") (10'8") (10'5") (10'7") (10'5")
4th Gear Forward kph 38.5 36.0 36.0 37.6 43.1 38(mph) (23.9) (22.4) (22.4) (23.4) (26.8) (23.6)
Hydraulic Cycle Time seconds 9 9 10.5 10.4 9.7 10.9
Tires 20.5 R25 L-3 17.5 R25 L-3 20.5 R25 L-3 17.5 R25 L-3 20.5 R25 L-2 20.5-25/12PR L-3
924H Hook-on Specification Comparisons
5
Deere
Cat 444K Case Volvo Komatsu Komatsu
924H Powerllel 521D XT L60F WA200-6 WA250PZ-6
Rated Net Power kW (hp) 96 (128) N/A 82 (110) N/A N/A N/Arpm 2300 N/A 2000 N/A N/A N/A
Max. Net Power kW (hp) 103 (138) 95 (128) 88 (118) 115 (154) 94 (126) 103 (138)rpm 1800 2000 2000 1700 2000 2000
Bucket Range m3 1.7-2.8 1.5-1.9 1.5 1.6-5.0 1.7-2.4 1.9-2.3(yd3) (2.2-3.6) (2.0-2.5) (2.0) (2.1-6.5) (2.2-3.1) (2.5-3.0)
Bucket used for specs m3 2.1 1.9 1.5 1.9 2.0 2.3with BOCE (yd3) (2.7) (2.5) (2.0) (2.5) (2.6) (3.0)
Operating Weight kg 11 635 12 074 10 858 11 800 10 550 11 000(lb) (25,651) (26,619) (23,928) (26,020) (23,259) (24,250)
Breakout Force kN 88.3 59.4 97.5 80.2 93.2 108(lb) (19,848) (13,352) (21,929) (18,020) (20,944) (24,250)
Straight Tipping Load kg 8126 7230 7218 8120 9690 8925(lb) (17,916) (15,940) (15,913) (17,910) (21,363) (19,676)
Full Turn Static Tipping Load kg 7098 6226 6190 7010 8345 7765(lb) (15,647) (13,726) (13,647) (15,450) (18,397) (17,119)
Articulation Angle degree 40 40 40 40 40 40
Wheelbase mm 2800 2760 2750 3000 2840 2900(ft in) (9'2") (9'1") (9'0") (9'10") (9'4") (9'6")
6
924H Hook-on Specification Comparisons
Deere
Cat 444K Case Volvo Komatsu Komatsu
924H Powerllel 521D XT L60F WA200-6 WA250PZ-6
Width Over Tires mm 2502 2415 2308 2440 2470 2470(ft in) (8'3") (7'11") (7'7") (8'0") (8'1") (8'1")
Dump Clearance mm 2759 2580 2734 2810 2830 2861(ft in) (9'1") (8'5") (9'0") (9'3") (9'3") (9'5")
Reach – full lift mm 1060 1140 1122 1040 930 1088(ft in) (3'6") (3'9") (3'8") (3'5") (3'1") (3'7")
Overall Length mm 7251 7150 6715 7310 6895 7337(ft in) (23'9") (23'5") (22'0") (24'0") (22'7") (24'1")
Loader Clearance Circle mm 11 194 11 230 10 871 11 590 11 700 12 236(ft in) (36'8") (36'10") (35'8") (38'0") (38'5") (40'2")
Hinge Pin Height mm 3881 3670 3739 3870 3705 3965fully raised (ft in) (12'9") (12'0") (12'3") (12'8") (12'2") (13'0")
Height to top of ROPS mm 3227 3170 3173 3220 3180 3200(ft in) (10'7") (10'5") (10'5") (10'7") (10'5") (10'6")
4th Gear Forward kph 38.5 36.0 37.6 43.1 38.0 38.0(mph) (23.9) (22.4) (23.4) (26.8) (23.6) (23.6)
Hydraulic Cycle Time seconds 8.9 9.0 10.4 9.7 10.9 10.6
Tires 20.5R25 L-3 17.5R25 L-3 17.5R25 L-3 20.5R25 L-2 20.5-25/ 20.5-25/12PR L-3 12PR (L2)
7
928Hz Pin-on Specification Comparisons
Cat Deere Case Volvo Komatsu
928Hz 544K Z-Bar 621E L70F WA250-6
Rated Net Power kW (hp) 111 (149) N/A 109 (146) N/A N/Arpm 2300 N/A 1800 N/A N/A
Max. Net Power kW (hp) 119 (160) 125 (167) 121 (162) 125 (168) 103 (138)rpm 2000 1900 1800 1700 2000
Bucket Range m3 2.0-2.3 1.9-2.3 2.0-2.3 2.0-6.4 1.9-2.7(yd3) (2.6-3.0) (2.5-3.0) (2.5-3.0) (2.6-8.4) (2.5-3.5)
Bucket used for specs m3 2.3 2.3 2.3 2.3 2.3with BOCE (yd3) (3.0) (3.0) (3.0) (3.0) (3.0)
Operating Weight kg 12 618 12 820 12 431 13 160 11 545(lb) (27,818) (28,263) (27,406) (29,020) (25,448)
Breakout Force kN 108.8 100.9 103.4 95.4 121.0(lb) (24,460) (22,672) (23,249) (21,450) (27,210)
Straight Tipping Load kg 9911 10 896 10 339 9770 11 960(lb) (21,850) (24,021) (22,795) (21,530) (26,367)
Full Turn Static Tipping Load kg 8585 9434 8998 8420 10 525(lb) (18,928) (20,799) (19,836) (18,570) (23,204)
Articulation Angle degree 40 40 40 40 40
Wheelbase mm 2900 2930 2900 3000 2900(ft in) (9'6") (9'7") (9'6") (9'10") (9'6")
928Hz Pin-on Specification Comparisons
8
Cat Deere Case Volvo Komatsu
928Hz 544K Z-Bar 621E L70F WA250-6
Width Over Tires mm 2570 2546 2523 2470 2470(ft in) (8'5") (8'4") (8'3") (8'1") (8'1")
Dump Clearance mm 2842 2760 2801 2790 2850(ft in) (9'4") (9'1") (9'2") (9'2") (9'4")
Reach – full lift mm 964 990 1013 1090 985(ft in) (3'2") (3'3") (3'4") (3'7") (3'3")
Overall Length mm 7304 7430 7384 7390 7055(ft in) (24'0") (24'4") (24'3") (24'3") (23'2")
Loader Clearance Circle mm 11 592 11 650 11 549 11 670 12 060(ft in) (38'0") (38'3") (37'11") (38'3") (39'7")
Hinge Pin Height mm 3872 3820 3830 3870 3795fully raised (ft in) (12'8") (12'6") (12'7") (12'8") (12'5")
Height to top of ROPS mm 3269 3240 3395 3280 3200(ft in) (10'9") (10'8") (11'2") (10'9") (10'6")
4th Gear Forward kph 37.7 35.7 38.6 44.5 38(mph) (23.4) (22.2) (24) (27.7) (23.6)
Hydraulic Cycle Time seconds 10.1 10.2 12.3 9.3 11.6
Tires 20.5R25 L-3 20.5R25 L-3 20.5R25 L-2 20.5R25 L-2 20.5R25 L-2
9
930H Hook-on Specification Comparisons
Deere
Cat 544K Case Volvo Volvo Komatsu Komatsu
930H Powerllel 621E XT L70F L90F WA250PZ-6 WA320PZ-6
Rated Net Power kW (hp) 111 (149) N/A 101 (136) N/A N/A N/A N/Arpm 2300 N/A 2000 N/A N/A N/A N/A
Max. Net Power kW (hp) 119 (160) 125 (167) 110 (148) 125 (168) 128 (172) 103 (138) 125 (167)rpm 2000 1900 2000 1700 1700 2000 2000
Bucket Range m3 2.1-5.0 1.9-2.3 2.0-2.4 2.0-6.4 2.3-7.0 1.9-2.3 2.5-2.7(yd3) (2.6-6.5) (2.5-3.0) (2.5-3.0) (2.6-8.4) (3.0-9.2) (2.5-3.0) (3.25-3.50)
Bucket used for specs m3 2.3 2.3 2.4 2.3 2.3 2.3 2.5with BOCE (yd3) (3.0) (3.0) (3.0) (3.0) (3.0) (3.0) (3.3)
Operating Weight kg 13 174 13 840 13 022 13 410 15 170 11 000 15 350(lb) (29,044) (30,571) (28,709) (29,580) (33,450) (24,250) (33,830)
Breakout Force kN 126.0 84.4 108.1 86.7 113.1 108 142(lb) (28,334) (18,968) (24,298) (19,490) (25,420) (24,250) (31,810)
Straight Tipping Load kg 9042 8791 8840 9180 10 700 8925 10 990(lb) (19,933) (19,382) (19,489) (20,240) (23,600) (19,676) (24,228)
Full Turn Static kg 7871 7554 7652 7870 9100 7765 9670Tipping Load (lb) (17,352) (16,654) (19,869) (17,360) (20,070) (17,119) (21,320)
Articulation Angle degree 40 40 40 40 40 40 40
Wheelbase mm 2900 2930 2900 3000 3000 2900 3030(ft in) (9'6") (9'7") (9'6") (9'10") (9'10") (9'6") (9'11")
930H Hook-on Specification Comparisons
10
Deere
Cat 544K Case Volvo Volvo Komatsu Komatsu
930H Powerllel 621E XT L70F L90F WA250PZ-6 WA320PZ-6
Width Over Tires mm 2580 2546 2523 2470 2490 2470 2590(ft in) (8'6") (8'4") (8'3") (8'1") (8'6") (8'1") (8'6")
Dump Clearance mm 2773 2680 2792 2710 2820 2861 2820(ft in) (9'1") (8'9") (9'2") (8'11") (9'3") (9'5") (9'3")
Reach – full lift mm 995 1090 1141 1180 1130 1088 1200(ft in) (3'3") (3'7") (3'9") (3'10") (3'8") (3'7") (3'11")
Overall Length mm 7686 7690 7593 7510 7550 7337 7750(ft in) (25'3") (25'3") (24'11") (24'8") (24'9") (24'1") (25'4")
Loader Clearance Circle mm 11 696 12 100 11 720 11 720 11 860 12 236 N/A(ft in) (38'4") (39'8") (37'8") (38'5") (38'11") (40'2") N/A
Hinge Pin Height mm 4090 3850 3956 3870 3960 3965 4005fully raised (ft in) (13'3") (12'8") (13'0") (12'8") (13'0") (13'0") (13'2")
Height to top of ROPS mm 3278 3240 3395 3260 3280 3200 3200(ft in) (10'9") (10'8") (11'2") (10'8") (10'9") (10'6") (10'6")
4th Gear Forward kph 38.3 35.7 38.6 44 46.2 38.0 38.0(mph) (23.8) (22.2) (24) (27.3) (28.7) (23.6) (23.6)
Hydraulic Cycle Time seconds 9.5 9.3 12.7 9.3 10 10.6 10.8
Tires 20.5R25 20.5R25 20.5R25 20.5R25 20.5R25 20.5-25/ 20.5-25/ L-3 L-3 L-2 L-2 L-2 12PR (L2) 12PR (L2)
924H High Lift Hook-on Specification Comparisons
11
Cat Deere Deere Volvo Volvo
924H 444K 544J L60F L70F
Bucket used for specs m3 2.1 1.9 1.9 2.1 2.1with BOCE (yd3) (2.7) (2.5) (2.5) (2.7) (2.7)
Dump Clearance mm 3267 2900 3063 3300 3240(ft in) (10'9") (9'6") (10'1") (10'10") (10'7")
Reach – full lift mm 1060 1150 1090 1083 1120(ft in) (3'6") (3'9") (3'7") (3'6") (3'8")
Hinge Pin Height mm 4387 3980 4188 4390 4340fully raised (ft in) (14'5") (13'1") (13'9") (14'5") (14'3")
Overall Length mm 7752 7380 7807 7890 7920(ft in) (25'5") (24'3") (25'7") (25'11") (26'0")
Operating Weight kg 11 754 11 548 13 180 12 000 13 620(lb) (25,913) (25,459) (29,057) (26,460) (30,040)
Breakout Force kN 88.3 60.3 80.5 85.1 88.3(lb) (19,848) (13,550) (18,104) (19,130) (19,860)
Straight Tipping Load kg 6621 7092 9176 6330 7480(lb) (14,596) (15,635) (20,230) (15,520) (16,510)
Full Turn Static Tipping Load kg 5751 6105 8164 5390 6370(lb) (12,679) (13,459) (17,999) (11,880) (14,040)
930H High Lift Hook-on Specification Comparisons
12
Case
Cat Deere Deere 621EXR Volvo Volvo Komatsu
930H 544K 624J Pin-on L70F L90F WA320-6
Bucket used for specs m3 2.3 2.3 2.7 2.3 2.3 2.3 2.3with BOCE (yd3) (3.0) (3.0) (3.5) (3.0) (3.0) (3.0) (3.0)
Dump Clearance mm 3273 3010 3020 3214 3200 3240 3595(ft in) (10'9") (9'10") (9'11") (10'7") (10'6") (10'8") (11'10")
Reach – full lift mm 994 1050 1240 1029 1160 1080 950(ft in) (3'3") (3'5") (4'1") (3'5") (3'9") (3'6") (3'1")
Hinge Pin Height mm 4549 4130 4340 4243 4340 4390 4545fully raised (ft in) (14'11") (13'7") (14'3") (13'11") (14'3") (14'5") (14'10")
Overall Length mm 8165 7900 8260 7792 7980 7960 8005(ft in) (26'9") (25'11") (27'1") (25'7") (26'3") (26'1") (26'3")
Operating Weight kg 13 322 13 271 15 597 12 521 13 660 15 420 14 550(lb) (29,370) (29,258) (34,386) (27,604) (30,130) (34,000) (32,080)
Breakout Force kN 126.0 78.1 95.0 106.4 84.7 115.1 133(lb) (28,334) (17,550) (21,358) (23,925) (19,040) (25,870) (29,980)
Straight Tipping Load kg 7190 8295 10 230 8473 7410 9050 9520(lb) (15,852) (18,286) (22,553) (18,680) (16,340) (19,960) (20,090)
Full Turn Static kg 6221 7110 9129 7338 6290 7640 8460Tipping Load (lb) (13,715) (15,676) (20,216) (16,178) (13,880) (16,850) (18,650)
938H Pin-On Specification Comparison
13
Cat Case Deere Volvo Kawasaki Komatsu938H 721E 624K L90F 70ZV-2 WA320-6
Net Power — kW (hp) 134 (180) 128 (172) 127 (170) — 125 (168) —SAE J1349, ISO 9249 rpm 2100 1800 2200 — 2400 —
Max. Net Power – kW (hp) 134 (180) 137 (183) 147 (198) 128 (174) — 124 (166)SAE J1349, ISO 9249 rpm 2100 2000 1800 1700 — 2000
Max. Gross Power – kW (hp) 147 (197) 145 (195) — 129 (175) — 127 (170)SAE J1995 rpm 2100 2000 — 1700 — 2000
Bucket Range m3 2.1-3.1 2.3-2.7 1.9-2.7 2.3-2.7 2.5-3.1 2.3-3.2(yd3) (2.8-4.1) (3.0-3.5) (2.5-3.5) (3.0-3.5) (3.3-4.0) (3.0-4.2)
Bucket used for specs m3 2.8 2.7 2.7 2.5 2.7 2.8with BOCE (yd3) (3.7) (3.5) (3.5) (3.3) (3.5) (3.7)
Operating Weight kg 14 992 14 500 22 716 14 980 14 260 14 370(lb) (33,043) (31,967) (33,477) (33,032) (31,437) (31,680)
Breakout Force kN 123 133 126.7 118.5 124.0 129.3(lb) (27,574) (29,805) (28,484) (26,640) (27,875) (29,060)
Straight Tipping Load kg 11 544* 12 526 13 922 11 210 11 350 12 535(lb) (25,442)* (27,615) (30,693) (24,716) (25,022) (27,635)
Full Turn Static Tipping Load kg 10 034* 10 856 12 031 9570 9720 11 140(lb) (22,115)* (23,933) (26,524) (21,106) (21,428) (24,560)
Articulation Angle degrees 40 40 40 40 40 40
Wheelbase mm 3020 3253 3330 3000 3050 3030(ft in) (9'10") (10'8") (10'1") (9'10") (10'0") (9'11")
John Deere 624K specs include optional 140 kg (309 lb) counterweight. Kawasaki 70ZV-2 specs include optional350 kg (770 lb) counterweight.*Static tipping loads conform to the international standard as defined in ISO 14397-1 (Sept2007).
938H Pin-On Specification Comparison
14
Cat Case Deere Volvo Kawasaki Komatsu
938H 721E 624K L90F 70ZV-2 WA320-6
Width Over Tires mm 2674 2562 2582 2490 2585 2585(ft in) (8'9") (8'5") (8'5") (8'2") (8'6") (8'6")
Dump Clearance mm 2771 2890 2870 2820 2815 2850(ft in) (9'1") (9'5") (9'5") (9'3") (9'3") (9'4")
Reach – full lift mm 1077 1172 1020 1130 1090 1035(ft in) (3'6") (3'10") (3'4") (3'8") (3'8") (3'5")
Overall Length mm 7342 7710 7750 7560 7600 7455(ft in) (24'1") (25'4") (25'5") (24'10") (24'11") (24'6")
Loader Clearance Circle mm 12 023 12 680 12 240 11 960 12 110 12 180(ft in) (39'5") (41'7") (40'2") (39'3") (39'8") (39'9")
Hinge Pin Height mm 3843 3980 3960 3960 3890 3905fully raised (ft in) (12'7") (13'1") (13'0") (13'0") (12'9") (12'10")
Height to top of ROPS mm 3356 3404 3330 3280 3335 3200(ft in) (11'0") (11'2") (10'11") (10'9") (10'11") (10'6")
4th Gear Forward km/h 43.2 38.0 39.5 46.2 37.8 38.0(mph) (26.8) (23.6) (24.5) (28.7) (23.6) (23.6)
Hydraulic Cycle Time seconds 10.3 10.7 10.0 10.0 10.5 10.6
Tires 20.5R25 20.5R25 20.5-25 20.5R25 20.5-25 20.5-25
IT38H Specification Comparisons
15
Cat IT38H with Case Deere Volvo
Fusion Coupler 721E XT 624K Powerllel L90F
Net Power — kW (hp) 134 (180) 128 (172) 127 (170) —SAE J1349, ISO 9249 rpm 2200 1800 2200 —
Max. Net Power kW (hp) 134 (180) 137 (183) 147 (198) 125 (168)SAE J1349, ISO 9249 rpm 1800 1800 1800 1700
Max. Gross Power – kW (hp) 147 (197) 145 (195) — 126 (169)SAE J1995 rpm 1800 2000 — 1700
Bucket used for specs m3 2.5 QC 2.4 QC 2.7 QC 2.5 QCwith BOCE (yd3) (3.3) (3.1) (3.5) (3.3)
Operating Weight kg 16 266 14 650 16 453 15 220(lb) (35,850) (32,298) (36,275) (33,550)
Breakout Force kN 122 118 105.5 108.5(lb) (27,514) (26,491) (23,719) (24,400)
Straight Tipping Load kg 10 436* 13 000 10 802 10 520(lb) (23,001)* (28,660) (23,814) (23,190)
Full Turn Static Tipping Load kg 8981* 12 016 9256 8940(lb) (19,795)* (26,491) (20,408) (19,710)
Articulation Angle degrees 40 40 40 40
Wheelbase mm 3020 3253 3070 3000(ft in) (9'11") (10'8") (10'1") (9'10")
John Deere 624K Powerllel specs include optional 140 kg (309 lb) counterweight.*Static tipping loads conform to the international standard as defined in ISO 14397-1 (Sept2007).*IT38H Specs are measured with Fusion Coupler. Fusion coupler information available on page 37-38.
IT38H Specification Comparisons
16
Cat IT38H with Case Deere Volvo
Fusion Coupler 721E XT 624K Powerllel L90F
Width Over Tires mm 2709 2550 2582 2490(ft in) (8'11") (8'4") (8'6") (8'2")
Dump Clearance mm 2733 2769 2690 2740(ft in) (9'0") (9'1") (8'10") (9'0")
Reach – full lift mm 1224 1272 1269 1210(ft in) (4'0") (4'2") (4'2") (3'11")
Overall Length mm 7543 8117 8130 7670(ft in) (24'8") (26'8") (26'8") (25'2")
Loader Clearance Circle mm 12 136 12 491 12 600 12 010(ft in) (39'9") (41'0") (41'4") (39'5")
Hinge Pin Height mm 3933 4161 3990 3960fully raised (ft in) (12'10") (13'7") (13'1") (13'0")
Height to top of ROPS mm 3356 3404 3330 3280(ft in) (11'0") (11'2") (10'11") (10'9")
4th Gear Forward km/h 43.2 38 39.6 46.2(mph) (26.8) (23.6) (24.6) (28.7)
Hydraulic Cycle Time 10.4 10.8 10.3 10.0– seconds
Tires 20.5R25 20.5-25 20.5-25 20.5R25
950H Pin-On Specification Comparison
17
Cat® Case Deere Kawasaki Volvo Komatsu950H** 821E 644K 80ZV-2 L110F WA380-6
Gross Power – SAE J1995 kW (hp) 161 (216) 157 (210) — 155 (208) 170 (231) 143 (192)rpm 1800 1800 — 2200 1700 2100
Net Power – ISO 9249 kW (hp) 147 (197) — — — — 142 (191)rpm 1800 — — — — 2100
Net Power – SAE J1349 kW (hp) 145 (195) 148 (198) 138 (185) — 169 (230) 142 (191)rpm 1800 1800 2200 — 1700 2100
Bucket Range m3 2.5-5.2 2.6-3.4 3.2-3.4 2.7-3.6 2.9-3.4 2.9-4.0(yd3) (3.3-6.8) (3.4-4.5) (4.3-4.5) (3.6-4.8) (3.8-4.4) (3.8-5.2)
Bucket used for specs m3 3.1 3.2 3.25 3.2 3.1 3.3with BOCE (yd3) (4.0) (4.2) (4.25) (4.2) (4.0) (4.3)
Operating Weight kg 18 197 17 166 18 242 17 830 18 300 17 580(lb) (40,106) (37,845) (40,224) (39,054) (40,349) (38,760)
Breakout Force kN 156 157.5 150.8 161.0 156.7 158(lb) (34,985) (35,408) (33,903) (36,193) (35,252) (35,495)
Straight Tipping Load kg 12 161* 14 351 13 207 13 880 13 120 14 560(lb) (26,804)* (31,639) (33,576) (30,600) (28,928) 32,100
Full Turn Static Tipping Load kg 10 473* 12 405 13 126 11 880 11 270 12 610(lb) (23,082)* (27,348) (28,937) (26,191) (24,842) (27,800)
Articulation Angle degrees 40 40 40 40 40 40
Wheelbase mm 3350 3340 3250 3200 3200 3300(ft in) (11'0") (10'11.5") (10'8") (10'6") (10'6") (10'10")
Kawasaki’s publication doesn’t specify which standards are used for engine power.Case bucket used for specs not published.*Static tipping loads conform to the international standard as defined in ISO 14397-1 (Sept2007).**950H configuration does not include NACD power package.Kawasaki 80ZV-2: The weight and load data includes optional counterweight, enclosed ROPS Cab, air conditioner.
155 (208)2200
950H Pin-On Specification Comparison
18
Cat Case Deere Kawasaki Volvo Komatsu
950H 821E 644K 80ZV-2 L110F WA380-6
Width Over Tires mm 2784 2890 2875 2680 2680 2780(ft in) (9'2") (9'5.6") (9'5") (8'9.5") (8'9") (9'1")
Dump Clearance mm 2814 2980 2840 2960 2880 2950(ft in) (9'3") (9'9") (9'4") (9'8.6") (9'5") (9'8")
Reach, full lift mm 1282 1110 1120 1130 1110 1150(ft in) (4'2") (3'8") (3'8") (3'8") (3'8") (3'9")
Overall Length mm 8086 7860 8050 8105 7850 8140(ft in) (26'6") (25'9") (26'5") (26'7") (25'9") (26'8")
Turning radius, mm 7016 6032 5486 6375 6350 6320bucket in carry (ft in) (23'0") (19'9") (18'0") (20'11") (21'2") (20'9")
Hinge Pin Height, mm 3992 4120 4060 4095 4030 4095fully raised (ft in) (13'1") (13'6.3") (13'4") (13'5") (13'3") (13'5")
Height to top of ROPS mm 3452 3450 3380 3448 3360 3390(ft in) (11'4") (11'3.8") (11'1") (11'4") (11'0") (11'2")
4th Gear Forward km/h 37.0 37.0 35.4 36.9 36.2 33.0(mph) (23.0) (23.0) (22.0) (22.9) (22.5) (20.5)
4th Gear Reverse km/h 40.0 — — 37.3 36.2 35.5(mph) (24.9) — — (23.2) (22.5) (22.1)
Hydraulic Cycle Time seconds 10.0 9.0 10.6 11.0 10.0 11.0
Tires 23.5R25 23.5R25 23.5R25 23.5-25 23.5R25 23.5-25
Cat 4th gear forward/reverse shown with 23.5-25 tires.
962H Pin-On Specification Comparison
19
Cat Deere Volvo Kawasaki Komatsu962H 724K L120F 85ZV-2 WA430-6
Gross Power – SAE J1995 kW (hp) 172 (230) — 180 (245) 173 (232)rpm 1800 — 1700 2100
Net Power – ISO 9249 kW (hp) 158 (211) — — — —rpm 1800 — — — —
Net Power – SAE J1349 kW (hp) 156 (209) 169 (227) 179 (243) — 172 (231)rpm 1800 — 1700 — 2100
Bucket Range m3 2.7-5.2 3.1-3.6 3.1-9.5 3.1-4.0 3.1-4.3(yd3) (3.5-6.8) (4.0-4.8) (4.1-12.4) (4.0-5.2) (4.1-5.6)
Bucket used for specs m3 3.5 3.6 3.6 3.7 3.5with BOCE (yd3) (4.5) (4.75) (4.7) (4.8) (4.6)
Operating Weight kg 18 821 19 130 19 430 20 990 18 530(lb) (41,481) (42,174) (42,839) (46,275) (40,852)
Breakout Force kN 148 141.2 138.0 181 179(lb) (33,272) (31,742) (31,020) (40,680) (40,333)
Straight Tipping Load kg 13 122* 16 489 13 340 15 990 14 960(lb) (28,921)* (36,352) (29,413) (35,252) (32,981)
Full Turn Static Tipping Load kg 11,317* 14 204 11 330 13 700 13 785(lb) (24,943)* (31,314) (24, 983) (30,203) (30,390)
Articulation Angle degrees 40 40 40 40 40
Wheelbase mm 3350 3250 3200 3300 3300(ft in) (11'0") (10'8") (10'6") (10'10") (10'10")
Kawasaki’s publication doesn’t specify which standards are used for engine power.*Static tipping loads conform to the international standard as defined in ISO 14397-1 (Sept2007).Kawasaki 85ZV-2: The weight and load data includes optional counterweight, enclosed ROPS Cab, air conditioner.
175 (235)2200
962H Pin-On Specification Comparison
20
Cat 4th gear forward/reverse shown with 23.5-25 tires.
Cat Deere Volvo Kawasaki Komatsu
962H 724K L120F 85ZV-2 WA430-6
Width Over Tires mm 2770 2770 2680 2930 2820(ft in) (9'1") (9'1") (8'9") (9'7.5") (9'3")
Dump Clearance mm 3002 2790 2820 3190 3015(ft in) (9'10") (9'2") (9'3") (10'5.5") (9'11")
Reach, full lift mm 1257 1140 1270 1025 1195(ft in) (4'1") (3'9") (4'2") (3'4.5") (3'11")
Overall Length mm 8282 8330 8130 8145 8460(ft in) (27'2") (27'4") (26'8") (26'8") (27'9")
Turning radius, mm 6759 6540 6370 6635 6335bucket in carry (ft in) (22'2") (21'5.5") (21'4") (21'9.5") (20'9")
Hinge Pin Height, mm 4182 4060 4110 4310 4165fully raised (ft in) (13'9") (13'4") (13'6") (14'1.5") (13'8")
Height to top of ROPS mm 3452 3380 3360 3531 3390(ft in) (11'4") (11'1") (11'0") (11'7") (11'1")
4th Gear Forward km/h 38.0 35.4 35.1 35.8 37.2(mph) (23.6) (22.0) (21.8) (22.2) (23.1)
4th Gear Reverse km/h 40.0 — 35.1 36.5 37.2(mph) (24.9) — (21.8) (22.7) (23.1)
Hydraulic Cycle Time seconds 10 10.2 10.0 12.1 11.4
Tires 23.5R25 23.5R25 23.5R25 26.5-25 23.5-25
IT62H Specification Comparisons
21
*Static tipping loads conform to the international standard as defined in ISO 14397-1 (Sept2007).*IT62H Specs are measured with Fusion Coupler. Fusion coupler information available on page 37-38.
Cat
IT62H with Volvo 644K
Fusion Coupler L120F w/QC Powerllel
Gross Power – SAE J1995 kW (hp) 172 (230) 180 (245) —rpm 1800 1700 —
Net Power – ISO 9249 kW (hp) 158 (211) — —rpm 1800 — —
Net Power – SAE J1349 kW (hp) 156 (209) 179 (243) 138 (185)rpm 1800 1700 2200
Bucket used for specs m3 3.1 3.1 QC 3.0with BOCE (yd3) (4.1) (4.1) (4.0)
Operating Weight kg 19 667 19 310 19 760(lb) (43,346) (42,574) (43,563)
Breakout Force kN 151 148.5 118(lb) (33,825) (33,387) (26,519)
Straight Tipping Load kg 12 581* 13 580 13 170(lb) (27,728)* (29,939) (29,035)
Full Turn Static Tipping Load kg 10 693* 11 550 11 277at 40° (lb) (23,567)* (25,465) (24,862)
Wheelbase mm 3350 3200 3250(ft in) (11'0") (10'6") (11'1")
IT62H Specification Comparisons
22
Cat
IT62H with Volvo 644K
Fusion Coupler L120F w/QC Powerllel
Width Over Tires mm 2885 2680 —(ft in) (9'6") (8'9") —
Dump Clearance mm 2785 2830 2790(ft in) (9'2") (9'3") (9'2")
Reach, full lift mm 1227 1270 1190(ft in) (4'0") (4'2") (3'11")
Overall Length mm 8498 8150 8510(ft in) (27'11") (26'9") (27'11")
Turning radius, mm 6727 6370 13 360bucket at carry (ft in) (22'1") (21'4") (43'10")
Hinge Pin Height, mm 4123 4110 4110fully raised (ft in) (13'6") (13'6") (13'6")
Height to top of ROPS mm 3452 3360 3380(ft in) (11'4") (11'0") (11'1")
4th Gear Forward km/h 38 35.1 36.5(mph) (23.6) (21.8) (22.7)
4th Gear Reverse km/h 40 35.1 —(mph) (24.9) (21.8) —
Hydraulic Cycle Time seconds 10.7 10.0 10.6
Tires 23.5R25 23.5R25 23.5R25
Cat 4th gear forward/reverse shown with 23.5-25 tires.
966H Pin-On Specification Comparison
23*Static tipping loads conform to the international standard as defined in ISO 14397-1 (Sept2007).
Cat Case Deere Volvo Komatsu
966H 921E 744K L150F WA450-6
Gross Power – SAE J1995 kW (hp) 213 (286) 221 (297) 215 (288) 211 (287) 204 (273)rpm 1800 1800 1800 1400-1700 2000
Net Power – ISO 9249 kW (hp) 195 (262) — — 210 (284) 203 (272)rpm 1800 — — 1400-1700 2000
Net Power – SAE J1349 kW (hp) 193 (259) 204 (274) 204 (274) 210 (284) 203 (272)rpm 1800 1800 — 1400-1700 2000
Bucket Range m3 3.5-6.4 4.0-4.4 4.0-4.4 3.5-6.8 3.8-5.2(yd3) (4.5-8.3) (5.3-5.8) (5.3-5.8) (4.6-8.9) (5.0-6.8)
Bucket used for specs m3 4.3 4.4 4.0 4.0 3.8with BOCE (yd3) (5.6) (5.8) (5.3) (5.3) (5.0)
Operating Weight kg 23 526 23 042 24 182 23 320 22 680(lb) (51,852) (50,692) (53,312) (51,413) (50,000)
Breakout Force kN 187 201.9 190.4 184.7 203(lb) (42,080) (45,398) (42,805) (41,524) (45,660)
Straight Tipping Load kg 16 290* 19 350 19 923 17 380 17 870(lb) (35,902)* (42,659) (43,923) (38,318) (39,397)
Full Turn Static Tipping Load kg 14 295* 15 336 17 123 15 280 15 550(lb) (31,507)* (33,810) (37,750) (33,688) (34,282)
Articulation Angle degrees 37 40 40 37 40
Wheelbase mm 3450 3400 3450 3550 3450(ft in) (11'4") (11'2") (11'4") (11'8") (11'4")
966H Pin-On Specification Comparison
24
Cat Case Deere Volvo Komatsu
966H 921E 744K L150F WA450-6
Width Over Tires mm 2950 3000 2946 2950 3010(ft in) (9'8") (9'9") (9'8") (9'8") (9'11")
Dump Clearance mm 3086 3067 3050 3000 3235(ft in) (10'2") (10'0") (10'0") (9'10") (10'7")
Reach, full lift mm 1294 1286 1210 1210 1185(ft in) (4'3") (4'2") (4'0") (4'0") (3'11")
Overall Length mm 8855 8815 9020 8610 8930(ft in) (29'1") (28'11") (29'7") (28'3") (29'4")
Loader Clearance Circle, mm 14 720 13 653 14 380 14 640 15 260bucket in carry (ft in) (48'4") (44'9") (47'2") (48'0") (50'1")
Hinge Pin Height, mm 4224 4278 4290 4350 4360fully raised (ft in) (13'10") (14'0") (14'1") (14'3") (14'4")
Height to top of ROPS mm 3600 3700 3510 3580 3500(ft in) (11'10") (12'1") (11'6") (11'9") (11'6")
4th Gear Forward km/h 37.4 37.4 39.5 37.3 34.9(mph) (23.2) (23.2) (24.5) (23.2) (21.7)
4th Gear Reverse km/h 37.4 — — 37.3 36.0(mph) (23.2) — — (23.2) (22.4)
Hydraulic Cycle Time seconds 9.9 11.0 11.0 11.6 11.3
Tires 26.5R25 26.5-25 26.5R25 26.5R25 26.5-25
Cat 4th gear forward/reverse shown with 23.5-25 tires.
972H Pin-On Specification Comparison
25
Cat Deere Volvo Kawasaki Komatsu972H 824K L180F 90ZV-2 WA480-6
Gross Power – SAE J1995 kW (hp) 229 (307) — 235 (320) 224 (300)rpm 1800 — 1400-1600 2000
Net Power – ISO 9249 kW (hp) 214 (287) — 234 (318) — 223 (299)rpm 1800 — 1400-1600 — 2000
Net Power – SAE J1349 kW (hp) 212 (284) 205 (275) 234 (318) — 223 (299)rpm 1800 2000 1400-1600 — 2000
Bucket Range m3 4.0-6.4 4.0-5.2 4.0-7.8 3.3-4.5 4.1-6.1(yd3) (5.2-8.3) (5.3-6.8) (5.3-10.2) (4.3-5.9) (5.4-8.0)
Bucket used for specs m3 4.7 4.6 4.6 4.0 4.6with BOCE (yd3) (6.2) (6.0) (6.0) (5.2) (6.0)
Operating Weight kg 25 574 26 210 26 540 23 250 24 725(lb) (56,366) (57,783) (58,512) (51,257) (54,510)
Breakout Force kN 222 185.4 214.7 205.9 212(lb) (49,987) (41,678) (48,310) (46,309) (47,660)
Straight Tipping Load kg 17 527* 20 509 20 900 18 295 20 420(lb) (38,630)* (45,213) (45,899) (40,333) (45,020)
Full Turn Static Tipping Load kg 15 237* 17 588 18 260 15 670 17 780(lb) (33,582)* (38,775) (40,259) (34,546) (39,200)
Articulation Angle degrees 37 40 37 40 40
Wheelbase mm 3450 3450 3550 3400 3450(ft in) (11'4") (11'6") (11'8") (11'2") (11'4")
Kawasaki’s publication doesn’t specify which standards are used for engine power.*Static tipping loads conform to the international standard as defined in ISO 14397-1 (Sept2007).Kawasaki 90ZV-2: The weight and load data includes optional counterweight, enclosed ROPS Cab, air conditioner.
205 (275)2100
972H Pin-On Specification Comparison
26
Cat Deere Volvo Kawasaki Komatsu
972H 824K L180F 90ZV-2 WA480-6
Width Over Tires mm 3002 3048 2950 2930 3010(ft in) (9'10") (10'0") (9'8") (9'7.5") (9'11")
Dump Clearance mm 3252 3200 3120 3130 3205(ft in) (10'8") (10'6") (10'3") (10'3") (10'6")
Reach, full lift mm 1291 1270 1230 1180 1410(ft in) (4'3") (4'2") (4'0") (3'10") (4'8")
Overall Length mm 9144 9270 8790 8700 9345(ft in) (30'0") (30'5") (28'10") (28'6") (30'8")
Loader Clearance Circle, mm 14 919 14 250 14 760 13 680 15 400bucket in carry (ft in) (48'11") (46'9") (48'5") (44'11") (50'6")
Hinge Pin Height, mm 4446 4500 4480 4360 4505fully raised (ft in) (14'8") (14'9") (14'8") (14'4") (14'9")
Height to top of ROPS mm 3606 3510 3580 3535 3500(ft in) (11'10") (11'6") (11'9") (11'7") (11'6")
4th Gear Forward km/h 36.9 39.5 37.3 34.0 34.5(mph) (22.9) (24.5) (23.2) (21.1) (21.4)
4th Gear Reverse km/h 38.8 — 37.3 35.0 35.6(mph) (24.0) — (23.2) (21.7) (22.1)
Hydraulic Cycle Time seconds 10.4 10.4 12.9 10.7 12.7
Tires 26.5R25 26.5R25 26.5R25 26.5-25 26.5-25
Cat 4th gear forward/reverse shown with 23.5-25 tires.
980H Pin-On Specification Comparison
27
Cat Case Volvo Kawasaki Komatsu Deere980H 1221E L220F 95ZV-2 WA500-6 844K
Net Power – kW (hp) 260 (349) 239 (320) 259 (352) 255 (340) 263 (353) 246 (330)SAE J1349 rpm 1800 2200 1600 2100 1900 1600
Net Power – kW (hp) 260 (349) — 259 (352) — 263 (353) —ISO 9249 rpm 1800 — 1600 — 1900 —
Gross Power – kW (hp) 293 (393) 250 (335) 261 (355) — 266 (357) — SAE J1995 rpm 1800 2200 1600 — 1900 —
Bucket Range m3 4.2-8.2 5.6-7.0 4.5-14.0 4.2-5.9 4.5-6.3 5.5-6.2(yd3) (5.5-10.7) (7.3-9.2) (5.9-18.3) (5.5-7.7) (5.9-8.2) (7.3-8.1)
Bucket used for specs m3 5.7 5.7 5.6 5.4 5.6 5.6 with BOCE (yd3) (7.5) (7.46) (7.3) (7.0) (7.3) (7.3)
Operating Weight kg 30 050 30 400 31 520 30 920 32 550 31 792 (lb) (66,231) (66,930) (69,494) (68,170) (71,760) (70,089)
Breakout Force kN 212 221.1 220.2 245 245 212.9 (lb) (47,653) (49,710) (49,575) (55,120) (55,115) (47,860)
Straight Tipping Load kg 21 527* 25 320 23 450 24 230 23 600 23 616(lb) (47,446)* (55,830) (51,702) (53,420) (52,030) (52,064)
Full Turn Static Tipping Load kg 18 878* 21 810 20 520 19 930 20 500 20 282(lb) (41,607)* (48,070) (45,240) (43,940) (45,195) (44,713)
Articulation Angle degrees 37 40 37 40 40 40 Wheelbase mm 3700 3700 3700 3560 3780 3710
(ft in) (12'2") (12'2") (12'2") (11'8") (12'5") (12'2")
Komatsu WA500-6 specs include optional 900 kg (1985 lb) counterweight.Deere 844J specs include counterweight.Cat 980H specs will change with the optional Aggregate Loader arrangement.John Deere bucket optional spill sheet brings capacity to 8.1 yd3.Volvo L220F bucket range includes light duty buckets.*Static tipping loads conform to the international standard as defined in ISO 14397-1 (Sept2007).Komatsu WA500-6 large 8.2 yd3 is for loose material.Kawasaki 95ZV-2: The weight and load data includes optional counterweight, AC, Enclosed ROPS Cab.
980H Pin-On Specification Comparison
28
Cat Case Volvo Kawasaki Komatsu Deere980H 1221E L220F 95ZV-2 WA500-6 844K
Width Over Tires mm 3227 3270 3170 3220 3190 3202(ft in) (10'6") (10'7") (10'5") (10'7") (10'6") (10'6")
Dump Clearance mm 3272 3230 3270 3220 3295 3330 (ft in) (10'9") (10'6") (10'9") (10'7") (10'10") (10'10")
Reach – full lift mm 1534 1430 1280 1350 1500 1500 (ft in) (5'0") (4'7") (4'2") (4'6") (4'11") (4'11")
Overall Length mm 9468 9690 9120 9280 9815 9650 (ft in) (31'1") (31'8") (29'11") (30'5") (32'2") (31'8")
Loader Clearance Circle mm 15 829 15 250 15 500 14 550 14 300 15 060 (ft in) (51'11") (50'0") (50'10") (47'9") (50'2") (49'5")
Hinge Pin Height mm 4505 4550 4680 4490 4755 4620fully raised (ft in) (14'9") (14'9") (15'4") (14'9") (15'7") (15'2")
Height to top of ROPS mm 3765 3840 3730 3760 3785 3760 (ft in) (12'4") (12'6") (12'3") (12'4") (12'5") (12'4")
4th Gear Forward km/h 36.3 34.0 32.8 34.0 38.8 37.6 (mph) (22.6) (21.1) (20.4) (21.1) (24.1) (23.4)
4th Gear Reverse km/h 41.5 — 32.8 — 43.2 —(mph) (25.8) — (20.4) — (26.9) —
Hydraulic Cycle Time seconds 11.5 11.3 10.6 12.2 13.1 11.3
Tires 29.5R25 29.5R25 29.5R25 29.5-25 29.5-25 29.5-25
29
Model Serial Numbers
MODEL Clayton Leicester CBL
924H HXC JTM KLN
924Hz BEF PED WLB
928H CXK BYD N/A
930H DHC FTD N/A
MODEL U.S. GOS SCM CBL
938H MJC LKM KLM JKM
IT38H N/A N/A N/A JNJ
950H K5K N1A J5J M1G
962H K6K N4A J6J M3G
IT62H N/A N/A N/A M5G
966H A6D A6G A6J N/A
972H A7D A7G A7J N/A
980H JMS MHG A8G N/A
H Series Wheel Loaders will have common serial number prefixes for CCS and SW.
30
Engines
Competitive Power Differences:
1. Volvo converts from kW to Metric Horsepower, not Standard Horsepower,which gives their machines an extra 3-5 hp on paper
2. Volvo reduces their Gross power by subtracting the parasitic losses fromthe alternator, muffler and air cleaner
3. Volvo advertises their Net power assuming much lower fan speeds(and power loss)
ENGINE SPEED (RPM)
Gross Net
Rated Gross
Rated Net
Max Gross
Max Net
31
Former Model Specifications
Model 938F 938G 938G II 950F 950F II 950G 950G II
Product ID# Prefix — 4YS CRD 7ZF 5SK 3JW/4BS AXX/AXR
Years Built 94-97 97-02 03-07 90-92 93-98 98-02 02-05
Flywheel Power kW 104 119 119 128 128 134 136(hp) (140) (160) (160) (170) (170) (183) (183)
Shipping Weight kg 13 030 12 962 13 452 16 086 16 880 16 904 18 339(lb) (28,730) (28,578) (29,656) (35,463) (37,220) (37,266) (40,430)
Rated Capacity m3 2.5 2.8 2.8 3.1 3.5 3.5 3.5(yd3) (3.25) (3.65) (3.65) (4.0) (4.5) (4.5) (5)
Breakout Force kN 133.2 110.1 109.4 146.7 146.7 146 138(lb) (27,180) (24,770) (24,594) (32,974) (32,980) (32,810) (31,024)
Width Over Tires m 2.61 2.6 2.6 2.76 2.76 2.89 2.89(ft in) (8'7") (8'6") (8'6") (9'0") (9'0") (9'6") (9'5")
Ground Clearance mm 400 400 399 474 460 400 412(in) (16") (16") (16") (18.7") (18.1") (16") (16")
Max. Reach @ Full Lift mm 1004 1055 1068 1160 1180 1270 1308(ft) (3'4") (3'6") (3'6") (3'10") (3'10") (4'2") (4'4")
Dump Clearance @ m 2.85 2.72 2.77 2.85 2.83 2.89 2.81Max. Height (ft) (9'4") (8'11") (9'1") (9'4") (9'3") (9'6") (9'2")
Maximum Speed – Forward km/h 37.9 39.4 38.0 39.3 38.7 37.0 37.0(mph) (23.6) (24.5) (23.6) (24.4) (24.0) (23.0) (23.0)
Maximum Speed – Reverse km/h 22.0 23.4 23.1 43.0 42.7 40.7 40.0(mph) (13.7) (14.5) (14.3) (26.7) (26.5) (25.3) (25.0)
32
Former Model Specifications
Model 960F 962G 962G II 966E 966F 966F II 966G 966G II
Product ID# Prefix 9ZJ 4PW/5AS AXY/AXS 99Y 4YG 1SL 3SW/3ZS ANZ/ANT
Years Built 94-98 98-02 00-05 87-90 90-93 93-98 98-02 00-05
Flywheel Power kW 149 149 152 161 164 164 175 184(hp) (200) (200) (204) (216) (220) (220) (235) (246)
Shipping Weight kg 18 070 17 941 19 992 20 324 20 466 21 290 22 068 21 979(lb) (39,840) (39,553) (44,075) (44,767) (45,119) (46,950) (48,651) (48,455)
Rated Capacity m3 3.5 3.8 3.6 3.8 3.8 3.8 4.0 4.25(yd3) (4.5) (5.0) (4.71) (5.0) (5.0) (5.0) (5.25) (5.5)
Breakout Force kN 142.3 142 132.9 185.6 201.18 204.90 196 189.1(lb) (31,970) (31,950) (29,877) (41,715) (45,187) (45,180) (44,120) (42,477)
Width Over Tires m 2.77 2.9 2.89 2.94 2.94 2.94 2.97 2.97(ft/in) (9'1") (9'8") (9'5") (9'8") (9'8") (9'8") (9'9") (9'7")
Ground Clearance mm 454 400 412 476 476 476 565 471(in) (17.9") (16") (16") (18.7") (18.7") (18.7") (22") (18.5")
Max. Reach @ Full Lift mm 1030 1250 1287 1290 1280 1277 1295 1328(ft) (3'5") (4'2") (4'2") (4'3") (4'2") (4'2") (4'3") (4'4")
Dump Clearance @ m 2.92 2.77 2.96 2.97 2.98 2.98 3.1 3.07Max. Height (ft) (9'6") (9'2") (9'7") (9'9") (9'9") (9'9") (10'2") (10'0")
Maximum Speed –Forward km/h 39.4 37.0 37.0 38.2 43.6 38.8 37.1 37.2
(mph) (24.5) (23.0) (23.0) (23.7) (27.0) (24.1) (23.1) (23.1)Reverse km/h 43.2 40.7 40 37.6 42.6 43.9 42.2 38.5
(mph) (26.8) (25.3) (24.9) (23.4) (26.4) (27.3) (26.2) (23.9)
33
Former Model Specifications
Model 970F 972G 927G II 980C 980F 980F II 980G 980G II
Product ID# Prefix 7SK 4WW/7LS AWP/ANY 63X 8CJ 8CJ 2KR AWH
Years Built 92-98 98-02 01-05 79-91 91-92 92-95 95-01 01-05
Flywheel Power kW 187 198 201 201 205 205 224 232(hp) (250) (265) (270) (270) (275) (275) (300) (311)
Shipping Weight kg 20 367 24 468 23 900 27 559 27 580 27 580 29 480 31 435(lb) (44,901) (53,942) (52,691) (60,755) (60,800) (60,800) (65,000) (69,302)
Rated Capacity m3 4.3 4.7 4.7 5.2 5.38 5.38 5.4 5.7(yd3) (5.6) (6.0) (6.0) (6.75) (7.0) (7.0) (7.0) (8.0)
Breakout Force kN 183 212 216.1 227.5 227.5 227.5 233 199(lb) (40,995) (47,580) (48,554) (51,121) (51,121) (51,121) (52,391) (44,785)
Width Over Tires m 2.94 2.97 2.97 3.15 3.15 3.15 3.25 3.25(ft in) (9'7") (9'9") (9'7") (10'4") (10'4") (10'4") (10'8") (10'8")
Ground Clearance mm 482 565 565 417 469 469 467 467(in) (19") (22") (22") (16.4") (18.54") (18.54") (18.4") (18.4")
Max. Reach @ Full Lift mm 1147 1255 1325 1480 1500 1500 1540 1540(ft) (3'9") (4'1") (4'4") (4'10") (4'11") (4'11") (5'1") (5'1")
Dump Clearance @ m –3.4 3.15 3.23 3.19 3.16 3.16 3.27 3.27Max. Height (ft) (10'10") (10'4") (10'7") (10'7") (10'5") (10'5") (10'9") (10'9")
Maximum Speed – Forward km/h 37.3 37 36.9 34.6 39.6 39.6 37.4 37.4
(mph) (23.2) (22.9) (22.9) (21.5) (24.5) (24.5) (23.2) (23.2)Reverse km/h 42.7 41.9 38.8 37.4 42.8 42.8 42.8 42.8
(mph) (26.5) (26.0) (24.0) (23.2) (26.6) (26.6) (26.6) (24.8)
34
Work Tools
Caterpillar offers the most complete range of work tools available for Cat® WheelLoaders. No matter the application Caterpillar® Work Tools are available to enhancethe performance of the machine, and meet your customers’ job requirements,providing a total package that no other manufacturer can touch. Key tools includequick couplers, forks, specialty buckets and brooms; and there are many more.
Many work tools can be shipped factory-installed. These are listed in the machineprice lists.
In addition, Caterpillar offers a complete line of work tools that can be shippedloose. These work tools are found in the WT-SWL (924H, 924Hz, 928Hz, 930H)or WT-WL (938H-980H) price lists in InfoCast. These loose work tool price listsare found in the same location as the machine price lists. From the dropdownmenu, select WT-SWL (Work Tools – Small Wheel Loaders) or WT-WL (WorkTools – Wheel Loaders).
For additional information or assistance, contact Cat Work Tools at 1-800-255-2372.
Fusion Coupler
Fusion provides flexibility across small and midsize wheel loader range:• 924, 924z, 928, 930, IT38, 938, 950, IT62, 962, 966, 972• G-series, H-series and future• One machine can pick any Fusion tool• Multiple machines share the same tools
35
Integral check valve keeps cylinderslocked in place — even if hoses arecompromised.
Direct connection between wedgeand cylinder is simple and reliable.Other couplers use complicatedcross-linkages, prone to wearand failure.
With Caterpillar on the side, youknow Fusion is backed by the world’slargest, most knowledgeable serviceorganization.
Open frame designpromotes better visibilityat ground level and truckbed heights.
Constructed of high-strength steels,and assembled to ISO9001 standards,the Fusion coupler endures like noother. Over 30,000 hours of on-the-job testing prove it.
A tight fit is achieved by cylindersdriving wedges down and into couplerpockets on the attachment. Tight fiteliminates rattle and premature wear,and substantially increases durabilityover traditional couplers.
High performancehydraulics are fullyintegrated withCat® Machines forflawless control.
Separate Fusioncontrol circuitkeeps third valvefree for runningother attachments.
Fusion coupler is integratedinto loader arms — minimizing offset, promoting moremachine performance.
Alignment indicators enhanceease of use for coupling anduncoupling in ideal andless-than-ideal conditions.
Long-stroke cylinderskeep wedges tight forthe life of the coupler.
Fusion Coupler (continued)
Literature:
The Power of Cat Fusion brochure GEDQ0224Cat Fusion Coupler System specalog GEHQ0185Wheel Loader Bucket card GEJQ0501
Product Bulletins:
Fusion Coupler System GEJQ0222Snow Removal Tools GEJQ0183Brooms GEJQ0002Rakes GEJL0199Material Handling Arms GEJQ0223Forks GEJQ0224
Video:
Cat Fusion Coupler – Sales & Operation Video GEVQ0001
36
37
Cat MWLs Fusion Coupler Specs
Model 938H IT38H 950H 962H IT62H 966H 972H
Rated Net Power – kW (hp) 134 (180) 135 (180) 161 (216) 172 (230) 173 (230) 213 (286) 229 (307)SAE J1349 rpm 2100 2101 1800 1800 1801 1800 1800
Rated Net Power – kW (hp) 134 (180) 135 (180) 147 (197) 158 (211) 159 (211) 195 (262) 214 (287)ISO 9249 rpm 2100 2101 1800 1800 1801 1800 1800
Rated Gross Power – kW (hp) 147 (197) 148 (197) 145 (195) 156 (209) 157 (209) 193 (259) 212 (284)SAE J1995 rpm 2100 2101 1800 1800 1801 1800 1800
Bucket Range m3 2.1-3.1 2.3-3.1 2.9-3.4 2.9-3.8 2.9-3.8 3.6-4.2 4.0-4.8(yd3) (2.8-4.0) (3.0-4.0) (3.8-4.5) (3.8-5.0) (3.8-5.0) (4.7-5.5) (5.2-6.3)
Bucket used for specs m3 2.9 2.5 3.1 3.4 3.1 4.2 4.8with BOCE (yd3) (3.79) (3.3) (4.1) (4.4) (4.1) (5.5) (6.3)
Operating Weight kg 15 522 16 266 18 561 19 402 19 667 23 838 25 852(lb) (34,210) (35,850) (40,908) (42,761) (43,345) (52,539) (56,978)
Breakout Force kN 111 122 154 141 151 186 220(lb) (25,041) (27,513) (34,514) (31,708) (33,825) (41,871) (49,371)
Straight Tipping Load* kg 11 190 10 436 11 999 13 429 12 581 16 115 17 427(lb) (24,663) (23,001) (26,447) (29,598) (27,728) (35,518) (38,409)
Full Turn Static Tipping Load* kg 9665 8981 10 295 11 457 10 693 14 109 15 108(lb) (21,302) (19,795) (22,689) (25,251) (23,567) (31,095) (33,298)
Articulation Angle degrees 40 40 40 40 40 40 40
Wheelbase mm 3020 3021 3350 3350 3351 3450 3450(ft in) (9'10") (9'10") (11'0") (11'0") (11'0") (11'4") (11'4")
*Static tipping loads conform to the international standard as defined in ISO 14397-1 (Sept2007).
38
Cat MWLs Fusion Coupler Specs (continued)
Model 938H IT38H 950H 962H IT62H 966H 972H
Width over tires mm 2700 2700 2927 2927 2927 3220 3224(ft in) (8'10") (8'10") (9'7") (9'7") (9'7") (10'6") (10'6")
Dump Clearance mm 2669 2818 2895 2812 2868 3062 3136(ft in) (8'9") (9'2") (9'5") (9'2") (9'4") (10'0") (10'3")
Reach – Full Lift mm 1135 1231 1337 1392 1355 1334 1275(ft in) (3'8") (4'0") (4'4") (4'6") (4'5") (4'4") (4'2")
Overall Length mm 7472 7601 8042 8247 8453 8682 9178(ft in) (24'6") (24'11") (26'4") (27'0") (27'8") (28'5") (30'1")
Loader Clearance Circle mm 12 067 12 195 13 340 13 397 13 523 14 717 14 936(ft in) (39'7") (40'0") (43'9") (43'11") (44'4") (48'3") (49'0")
Hinge Pin Height fully raised mm 3843 3933 3992 4182 4123 4224 4446(ft in) (12'7") (12'10") (13'1") (13'9") (13'6") (13'10") (14'8")
Height to top of ROPS mm 3356 3357 3452 3452 3453 3600 3606(ft in) (11'0") (11'0") (11'4") (11'4") (11'4") (11'10") (11'10")
4th Gear Forward km/h 43 44 37 38.0 38.0 37.4 36.9(mph) (26.8) (26.8) (23.0) (23.6) (23.6) (23.2) (22.9)
4th Gear Reverse km/h — — 40.0 40.0 40.0 37.4 38.8(mph) — — (24.9) (24.9) (24.9) (23.2) (24.0)
Hydraulic Cycle Time km/h 10.3 10.4 10.0 10.0 10.0 9.9 10.4
Tires km/h 20.5R25 20.5R25 23.5R25 23.5R25 23.5R25 26.5R25 26.5R25
39
Structures
Caterpillar ManufacturedAll components designed, analyzed, and tested
Linkage
VersaLink™ – 924H, 930H
Provides parallel lift andZ-bar performance
Z-Bar Linkage – 924Hz,
928Hz, 938H, 950H,
962H, 966H, 972H, 980H
Offers excellent dumpclearance, reach andbreakout force at lowbucket position
8-Bar Parallel Lift –
IT38H, IT62H
Ideal for load levelthroughout the lift cycle,especially with forksLess than 2° fluctuationfrom parallel through lift
40
Structures (continued)
Frames
40-degree articulation (924H-930H/938H/IT38H-962H/IT62H)37-degree articulation (966H-980H)80% robotically welded (938H-980H)Spread hitch design; double tapered roller bearingsArticulation neutralizer valves (except on 924H-938H/IT38H)Engine End Frame (EEF) – Provides a strong, rigid structure
that resists twisting and impact loadsNon-Engine End Frame (NEEF) – a four plate loader tower (IT38H, 950H-980H)that absorbs all forces associated with loading, twisting and penetration.The 938H uses a two plate design.
41
Axles
Caterpillar designed and manufacturedFour-piece design – 924H-930H and 950H-972HOne-piece housing – 980HMulti-piece housing – 938H/IT38H
Oscillating rear axle – allows for four wheels to remain on the groundover uneven terrain, which equates to excellent stability and traction.
(±12° – 924H-930H, 938H/IT38H)(±13° – 950H-980H)
Maximum single-wheel rise and fall travel
924H-930H – 423 mm (16.6") – 17.5 tires,924H-930H – 326 mm (12.8") – 20.5 tires938H, IT38H – 420 mm (16.5")950H, 962H, IT62H – 470 mm (18.5")966H, 972H – 502 mm (19.8")980H – 550 mm (21.7")Duo-Cone™ Seals between axle and housing minimizing contamination – 924H-980HRear axle trunnion has remote lubrication fitting – 924H-980H
42
Axles (continued)
Standard differential lock front – 924Hz (Clayton build), 924H, 930H and
938H/IT38H
Standard open differential front – 928Hz
Optional limited slip differential, front and rear – 950H-980H
Optional limited slip differential, rear – 924Hz, 924H, 928Hz and 930H
Traction Aids – Optional
Standard Manual Front Diff Lock – 938H/IT38H
Optional Automatic Front/Rear Diff Lock – 938H/IT38H
Final Drives and Brakes
Inboard final drives (protect from mud, sand and debris) – 924H-930H, 950H-972HOutboard final drives (provides easy access when service is required)
– 938/IT38H, 980HAdjustment-free, fully enclosed oil-disc brakes – 924H-980HBrake wear indicator – 938H-980H
(determines brake life without disassembling the axle)Axle oil cooler optional
43
Hydraulics
Hydraulic System
Load Sensing Pilot Operated Hydraulic Implement System – 924H, 924Hz, 930Hand 938H/IT38• Closed Center Hydraulic System provides flow and pressure upon demand
and only in the amounts needed• Variable Displacement Piston Pump – 924H, 924Hz, 930H, and 938H/IT38H• SP3C Valve (930H only) – Enables simultaneous lift and tilt functions for
improved material retention and cycle times. Additional functions such asride control (optional), anti-drift, and pilot supply are incorporated for areduction in hose routings
• Integrated 3rd function with electrohydraulic control (3rd function only)on versalink models (924H and 930H)
• Optional flow control available on versalink models (924H and 930H)Open Center Hydraulic Implement System – 928Hz and 980H
• Vane Type Pump
44
Hydraulics (continued)
Load Sensing Hydraulic Implement System – 950H-972H• Closed Center Hydraulic System provides flow and pressure upon demand
and only in the amounts needed• 950H-972H improved hydraulic system has 20% force lift increase (improved
cycle times) and a fuel efficiency advantage with competitors of 5-15%depending on application requirements
• Variable Displacement Piston Pump – 950H-972H• Priority Promotional Pressure Compensated Sectional Valve – simultaneous
lift and tilt functions for improved material retention and cycle times).Additional functions like ride control (optional), anti-drift, and pilot supplyare incorporated for a reduction in hose routings
XT™3 hoses with reusable couplings
Hydraulic Controls
Pilot Hydraulics – 924H-930H, 938H/IT38H (w/FNR joystick)Electro-hydraulic – 950H-972H (both conventional and command control steering)
and 980H (command control steering)
45
Hydraulics (continued)
Options
Optional Joystick* – 938H-980HOptional Third Valve** – 924H, 924Hz, 928Hz, 930H, 938H/IT38H-980HOptional Fourth Valve – 924Hz, 928Hz, 930H, 938H/IT38HOptional Fifth and Sixth Valve – 930HIntegrated Third Function Joystick w/Adjustable Flow – 924H, 930H, 950H-972HDual mode steering – 930HOptional Ride Control – 924H-980HOptional Payload Control System – 950H-980H
*FNR switch in 980H joystick is not integrated.** Third valve is standard on the 924H and 930H built at the Clayton factory.
46
Serviceability — 924H-930H
Extended serviceintervals reduce
machine service timeand increase machine
uptime. 4,000 hourhydraulic oil change1,000 hour hydraulic
filter change andstandard extended life
coolant/antifreeze
Extended serviceinterval of 500 hours
for engine oil changes
Firewall separates enginefrom cooling compartment
allowing systems to runmore efficiently
Durable XT hoses areindividually labeled,
allowing for easyidentification
Maintenancefree batteries
Easy access and minimal maintenance requirements provide exceptional ease of service
Vertically mounted andspaced spin-on filtersallow for convenient
and fast filter changes
Standard electric fuel-priming pump
Large upward-opening gull wing
doors and dropdown service panels
allow easy,ground level access
to service points
Wide spacingbetween radiators
allows forconvenient and
spacious cleaningof debris, keepingthe cooling systemoperating efficiently
Swing-outcooling fan allows
quick, easy cleaningand service of the
radiator whilekeeping lownoise levels
Scheduled OilSampling ports arefactory installed forimproved access to
engine, transmissionand hydraulic oils
47
Serviceability – 938H/IT38H
Tilting one piece, slopinghood provides complete
access to engine andcoolant compartmentsas well as best in class
rear visibility
Ground-level sightgauges for transmission(left side hitch area) andhydraulic tank (left sidebehind cab) offer ease
of daily checks
Electric Service Center located behind left-sideaccess ladder allows for easy, ground-levelaccess to circuit breakers, hood-tilt actuator,
master switch, and jump-start receptacle
Manual front differential lock (standard) andfront/rear automatic differential lock (optional
attachment) maximize machine capability in poorunderfoot conditions with ‘on the fly’ engagement
Outboard final drives and brakes provide easyaccess when service is required
Standard airborne debrisrear grill and 6 fins/inch
core spacing provideeasier cleaning andgreater resistance
to plugging
Right side service doorhouses engine oil fill
tube, engine oil dipstick,coolant shunt tank/fluid
level check and airrestriction indicator
Electronic fuel primingpump allows quick
and easy priming ofprimary filter.
Ground-level HydraulicService Center provides
easy access totransmission and
hydraulic oil filters aswell as hydraulic tankdrain and S•O•S ports
Grouped ground level grease points and remotepressure taps facilitate easy lubrication of vital
points and check of select system pressures
48
Serviceability — 950H-972H
• A new corrugated andperforated swing outrear grill minimizesentry of debris
• Cooling cores are6 fins per inch andprovide for easiercleaning and greaterresistance to plugging
Ground-levelsight gauges for
transmission (behindleft access ladder) andhydraulic tank (left sidebehind cab) offer ease
of daily checks
Right sideservice doorhouses the
engine oil filltube, and the
engine oildipstick
Under the hood, fuel filters withelectric priming pump allow easy switchof toggle switch for priming the system
vs. manual priming of Volvo andKomatsu; ease of serviceability and
elimination of contamination;COMPETITIVE ADVANTAGE
Ground level, grouped grease pointsand remote pressure taps facilitate easy
lubrication of vital points and easycheck of pressure ports for steering,hydraulic, transmission (optional),
and brake systems
Additional Options:
• Windshield-cleaning packagefor ease of cleaning
• Autolube system for preciselubrication of pin and bushingslowers operating costs
Service Intervals:
• 500 hours: engine oil andhydraulic filters
• 1000 hours: transmission filter
Electric Service Centerlocated by left-side
access ladder allowsfor easy, ground-level
access to circuit breakers,hood-tilt actuator, master
switch, and jump-startreceptacle
Ground-level HydraulicService Center with
easy access totransmission oil and
hydraulic filters as wellas hydraulic oil tank
drain port
Left side service door
houses groundlevel coolantsite gauge
49
Serviceability — 980H
Electro-hydraulic hoodtilts in 30 seconds for full
access to the engine,cooling system, andmajor components
• A new corrugated andperforated swing outrear grill minimizesentry of debris
• Cooling cores are6 fins per inch andprovide for easiercleaning and greaterresistance to plugging
Air cleaneraccessibility
without liftingthe hood
Ground-levelaccess to slide-
out batteries
Ecology drainsfor engine,
transmission,and hydraulic oil
Service Intervals:
Engine Oil Filter: 500 hoursTransmission Filter: 1000 hoursHydraulic Oil Filter: 500 hours
Transmissionsight gauge
Right side service doorhouses ground levelcoolant sight gauge,
engine oil fill, in-cab airfilter indicator, engine oil
dipstick, engine oil filltube, master switch,and optional jump
start receptacle
Electric fuel-priming pump
Optional Autolubeprovides precise, automaticlubrication while machine
is operating
Brake wearindicators
Remotepressure taps
Optional windshield-cleaning package for
better access
Right-side, hydrauliclevel sight gauge
50
Engine: 924H/924Hz/930H/928Hz
Caterpillar® C6.6 6-cylinder engine, U.S. EPA Tier 3 compliant6.6 L (403 in3) displacement
Direct-injection, electronic rotary fuel pump for accurate fuel deliveryThree-ring, controlled-expansion pistons
Lubricated by oil from piston cooling jetsGear-driven water pump and oil pumpReplaceable dry liners supported over entire lengthReplaceable valve guides and seatsIntegral plate-type oil coolerDeep skirted, internally-stiffened cast iron blockOne-piece cast iron cylinder heads – 2 valves per cylinderFuel priming pump and fuel/water separator standardClosed Circuit Breather (CCB)S•O•SSM sampling valve – engine oilCooling package provides better operation and serviceabilitySeparate air intake system
Isolates cooling air from engine air to provide ambient air to radiator core
51
Engine: 924H/924Hz/930H/928Hz
924H/924Hz 930H/928Hz
Rated Net Power kW 96 111
Horsepower (hp) (128) (149)
RPM 2300 2300
Maximum Net Rated kW 103 119
Horsepower (hp) (138) (160)
RPM 2000 2000
Torque Rise 59% 66%
Fuel Tank – L 225 225
dry fill (gal) (59.4) (59.4)
52
Engine: 938H/IT38H
EPA Tier 3, EU Stage III compliantConstant Net Horsepower at full parasitic loadOn-demand cooling fan improves fuel efficiency, less noise, and reduced
radiator pluggingEngine Idle Management System (EIMS) maximizes fuel efficiency
and provides flexibility
938H/IT38H
Engine Model Caterpillar C6.6 with ACERT Technology
Gross Power – SAE 1995 kW (hp) 147 (197)
Net Power – ISO 9249 kW (hp) 134 (180)
Net Power – SAE J1349 kW (hp) 128 (172)
RPM 2100
Displacement L (in3) 6.6 (402.8)
Fuel Tank – Standard L (gal) 247 (65.2)
53
Engine: 950H, 962H, IT62H
U.S. EPA Tier 3 and EU Stage III emissions compliantConstant Net Horsepower at full parasitic loadOn-demand cooling fan improves fuel efficiency, less noise, and reduced
radiator pluggingEngine Idle Management System (EIMS) maximizes fuel efficiency and
provides flexibility
950H 962H/IT62H
Engine Model Cat C7 with ACERT™ Technology
Gross Power – SAE 1995 kW (hp) 162 (217) 172 (230)
Net Power – ISO 9249 kW (hp) 147 (197) 158 (211)
Net Power – SAE J1349 kW (hp) 145 (195) 156 (209)
RPM 1800
Displacement L (in3) 7.2 (439)
Fuel Tank – Standard L (gal) 314 (83)
54
Engine: 966H, 972H
U.S. EPA Tier 3 and EU Stage III emissions compliant6 fins-per-inch, square wave core design on radiator decrease blockagesConstant Net Horsepower at full parasitic loadOn-demand cooling fan improves fuel efficiency, less noise, and reduced
radiator pluggingEngine Idle Management System (EIMS) maximizes fuel efficiency
and provides flexibility
966H 972H
Engine Model Cat C11 Cat C13ATAAC ATAAC
Gross Power – SAE 1995 kW (hp) 213 (286) 232 (311)
Net Power – ISO 9249 kW (hp) 195 (262) 214 (287)
Net Power – SAE J1349 kW (hp) 193 (259) 212 (284)
RPM 1800
Displacement L (in3) 11.1 (677) 12.5 (762.8)
Fuel Tank – Standard L (gal) 380 (100.4)
55
Engine: 980H
U.S. EPA Tier 3 and EU Stage III emissions compliant6 fins-per-inch, square wave core design on radiator decrease blockagesConstant Net Horsepower at full parasitic loadOn-demand cooling fan improves fuel efficiency, less noise, and reduced
radiator pluggingEngine Idle Management System (EIMS) maximizes fuel efficiency and
provides flexibility
980H
Engine Model Cat C15 Engine with ACERT™ Technology
Gross Power – SAE J1995 kW (hp) 293 (393)
Net Power – ISO 9249 kW (hp) 260 (349)
Net Power – SAE J1349 kW (hp) 260 (349)
RPM 1800
Displacement L (in3) 15.2 (928)
Fuel Tank – Standard L (gal) 479 (127)
56
Transmission: 924H-980H
Countershaft Automatic Powershift Transmission with Electronic Clutch PressureControl (ECPC) (924H-930H and 938H/IT38H
Planetary Automatic Powershift Transmission with Electronic Clutch PressureControl (ECPC) (950H-980H)
For both transmissions (924H – 980H):
• Modulates clutch engagement individually to provide smoother shiftsand longer component life
• Electronic controls provide the operator with choice between automaticand manual transmission shift modes
• Oil level sight gauges• Programmable transmission neutralizer – can be recalibrated using Cat ET
(924H-930H, 938H/IT38H are operator programmable)• Single control for both speed and direction
924H-930H
• Quick gear kickdown button on lift lever• High contact gears are precision ground for quieter operation
950H-980H
• Caseless (clutch housing encloses planetary trains)• Ecology drain (option)• Two Steering Systems (except 980H where command control steering is standard)
• Conventional Steering (standard) – quick gear kickdown button on implement pod• Command Control Steering (optional) – thumb operated upshift/downshift
rocker switch
57
Transmission: 924H-980H (Continued)
Maximum Travel Speeds
924H and 924Hz – 4 speeds forward, 3 speeds reverse
38.5 km/h (23.9 mph) forward21.8 km/h (13.5 mph) reverse
924H and 924Hz Low Speed Transmission
3.7 km/h (2.3 mph) forward in 1st4.1 km/h (2.5 mph) reverse in 1st
928Hz – 4 speeds forward, 3 speeds reverse
37.7 km/h (23.4 mph) forward25.8 km/h (16 mph) reverse
930H – 4 speeds forward, 3 reverse
38.3 km/h (23.8 mph) forward 24.1 km/h (15 mph) reverse
938H/IT38H – 4 speeds forward, 3 speeds reverse
43.2 km/h (26.8 mph) forward25.5 km/h (15.8 mph) reverse
58
Transmission: 924H-980H (Continued)
950H – 4 speeds forward, 4 speeds reverse
37.0 km/h (23.0 mph) forward40.0 km/h (24.9 mph) reverse
962H/IT62H – 4 speeds forward, 4 speeds reverse
38.0 km/h (23.6 mph) forward40.0 km/h (24.9 mph) reverse
966H – 4 speeds forward, 4 speeds reverse
37.4 km/h (23.2 mph) forward37.4 km/h (23.2 mph) reverse
972H – 4 speeds forward, 4 speeds reverse
36.9 km/h (22.9 mph) forward 38.8 km/h (24.0 mph) reverse
980H – 4 speeds forward, 4 speeds reverse
36.3 km/h (22.6 mph) forward 41.5 km/h (25.8 mph) reverse
59
Operator Station: 924H-930H
Load-sensing steering systemprovides low effort operatorcontrol. Optional QuickSteer,
dual mode steering forextremely low effort andaggressive truck loading
on the 930H
Two-door designmakes access
and egress easywith 180-degree
locking doors
Generous storageareas and cup holder
Optional rearview cameradisplayed ona 7 inch colorLCD monitor
Auxiliary hydraulicswith optional IntegratedThird Function Joystick
Controls
Sound suppressedand pressurized cab
Standard adjustablesuspension seat with armrestwith seat upgrades available
Safer ingress and egresswith a sloped ladder and
additional wider steps
Electric defrost andoptional external heated
rear view mirrors
Ergonomic design emphasizes comfort, visibility and easy operation
Standard heater and A/Cin Clayton build product
Adjustable armrest
Excellent visibility with distortion-free, flatglass, with wet-arm wipers on front and back
Updated sealed white facedgauge cluster with large LCD
and fault code display capability
60
Operator Station: 938H and IT38H
Excellent visibility with distortion-free, flat glass to cab floor, wet-arm wipers onfront and back, overhang to reduce glare, optional rear vision camera and HID lights.
Optional Cat Comfort Air Suspension Seat, 6-way adjustable clothseat with automotive-style lumbar support; Optional heated seat
Tilting steering column
Centrally-located gauges,status indicators, and
alert indicators
Messenger interfaceprovides in-cabadjustment of
transmission neutralizersettings and shift points
as well on-boardmachine diagnostics
and performance data
Optional joystick withintegrated FNR switch,transmission kickdown
and horn buttons
Integrated, right-sidearmrest, 2-way
adjustable and canbe formed for
optimal comfort
Low-effort, loadsensing, hydraulic
steering
180-degree, rear hingedleft and right sideaccess doors withstandard sliding
windows.
61
Operator Station: 950H-980H
180-degree leftrear-hinged door
with 5 degreeinclined access
ladder and fully-functional right-
access door
Low-efforthydraulic
conventionalsteering system(950-972) with
option forcommand
control steering(standard for 980)
GenerousStorage Areasand Cup holder
Cat Comfort Air Suspension Seat, 6-way adjustable withautomotive-style lumbar support; Optional heated seat
HVAC systemwith 13 vents
Electro-hydraulicfingertip controls
Integrated, right-side armrest,
3-way adjustable
Pressurized and sound-suppressed ROPS/FOPS cab
Fine modulationhydraulic mode
Implementcontrols with
programmablekick-outs, variable
shift control,optional Aggregate
Autodig
Optional heatedmirrors
Tilting and telescopicsteering column
Excellent visibility with distortion-free, flat glass to cab floor,wet-arm wipers on front and back, overhang to reduce glare,
optional rear vision camera, and optional HID lights
924H-930H Key Features
VersaLink™ Loader Linkage (924H, 930H) – Loader linkage provides unsurpassedvisibility, versatility and stability. The single piece boom-style lift arm designoffers exceptional strength, rigidity and visibility. A high lift version is availablefor high-dump or long reach requirements.
Load-Sensing Hydraulics (924H-930H) – Driven by a variable displacement axialpiston pump, the load-sensing, variable flow hydraulic system senses workdemand and adjusts flow and pressure to match.
Diff-Lock (924H, 924Hz, 930H) – Front axles feature diff-lock as standard and canbe actuated on the go by a foot pedal on demand.
Simplified Routine Service (924H-930H) – Gull-wing engine enclosure doors lockin position with gas struts while access panels in the frame can be foldeddown for exceptional access to filters and service points, all accessible fromthe ground level.
Additional Productivity Features (924H-930H) – The 924H-930H wheel loadershave outstanding power to weight ratios. The Cat C6.6 engine provides cleaner,quieter operation while delivering superior performance and durability.
Parallel Lift (924H-930H) – Parallel lift simplifies working with palletized orstacked material.
Ride Control System (924H-930H) – The optional Ride Control System providesa comfortable ride at all speeds and improves hard bank digging.
62
924H-930H Key Features (continued)
Reversing Fan (924H-930H) – Optional reversing capability of the fan cleansscreens without interrupting machine operation.
HID Lights (924H-930H) – High Intensity Discharge lights are available as anoptional addition to the deluxe cab.
Operator Programmable Transmission Neutralizer (924H-930H) – The transmissionneutralizer can be programmed by the operator within seconds, setting thesystem to optimum pressures.
Access/Egress (924H-930H) – Angled stairs with equally spaced steps are widerfor more comfortable and secure footing.
Optional Rear View Camera System (924H-930H) – This work area visualenhancement system utilizes a closed circuit video monitoring system.
63
64
938H-980H Key Features
Caterpillar Medium Wheel Loaders has a number of key features, (standard andoptions) that make the machines more productive, easier to operate, andultimately benefit our customers. Below is a brief highlight of these features.
Command Control Steering – Puts all steering and transmission controls at yourfingertips while reducing repetitive steering motionsAlternative Option to Steering Wheel in 950H-972HStandard feature in the 980H
Optional Aggregate Auto (available on the 950H-980H) – Automated system thatallows all operators to consistently get full payloads without touching the controls
Integrated Braking System (Standard on 938H-980H)Extend brake life and roll up smoothly to dump targets with this Caterpillarexclusive feature
Engine Idle Management System (Standard on 938H-980H)A new engine idle software package, to help maximize fuel efficiency, andallow customer flexibility in managing idle conditions for their applicationAvailable with four idle control settings: work mode, hibernate mode, lowvoltage mode, and warm-up mode
Hydraulic and Electrical Service Centers (Standard 938H-972H)Allows ground level access to key components and filters
65
938H-980H Key Features (continued)
Payload Control System (Option on the 950H-980H)Loads exact amounts of material and keep trucks moving quickly in the yard
Ride Control (Option on the 938H-980H)Improve ride performance and load retention when traveling over rough terrain
Windshield Cleaning Package (950H-980H) – Optional windshield cleaning packagemakes it easy to access the full windshield area. Consists of one step and oneplatform located on the loader frame, and two additional handrails.
High Intensity Discharge (HID) Lights (938H-980H) – Offer two times more lightthan 65-watt halogen lights and are six to ten times more durable.
Rear-Camera Option (938H-980H) – easily mounted to the hood for improvedviewing of the jobsite
Autolube (938H-980H) – System lubricates pins and bushings while the machineis in operation minimizing downtime and reducing maintenance cost
Product Link (Standard on the 938H-980H)Communicate vital machine information between the machine system,the Cat dealer, and the customer
Variable Pitch Fan (938H-972H) – This fan unit reverses airflow to purge debrisfrom the radiator by periodically rotating each individual fan blade 180 degrees.
Auto Reversing Fan (980H) – This fan unit reverses airflow to purge debris fromthe radiator by periodically reversing the rotation of the fan.
66
Market Segment Application Offerings
Steel Mill Arrangement (972H and 980H)
• Features that allow 972H and 980H to work in steel mill applications forhandling industrial material, hot slag, and processing scrap
• Enhanced guarding and high temperature hose protection• Rubber mounted front glass (quick change), steel overhanging roof cap,
heavy duty transmission and engine mounts (980H only), steel cable steps,heat isolated battery mounts, turbine precleaner, secondary steering,Ecosafe lubricant, and narrow steel front fenders.
• Parking brake override, transmission override, and engine shutdown switchat ground level
• Price List info: 331-9943 for 980H, 303-4178 for 972H
Segment Version 938H 950H 962H 966H 972H 980H
Steel Mill X X
Forestry Arrangement X X X
Waste Arrangement X X X X X
Corrosion Resistance X X X
67
Market Segment Application Offerings
Forestry Arrangement (950H, 966H and 980H)
• Enhanced features for improved durability and versatility in machinesworking in forestry applications
• Includes hydraulic 3rd valve, ride control, heavy duty tilt cylinder, additionalcounterweight, enhanced transmission, and guarding
• Increased tilt capacity for load controllability• Price List info: 244-5421 for 950H, 236-9131 for 966H, and 329-6624 for 980H
Industrial Arrangement (930H, 950H-980H)
• Provides additional guarding and features needed for machines in applicationin waste transfer stations, recycling centers, etc.• Guarding includes axle seal guards, front driveshaft guard, headlight guards,
hinged and electrically actuated power train and crankcase guards, etc.• Cooling system is six (6) fins per inch standard for all cores for H-Series machines• High lift, hydraulic option in price list• Additional options include: Cab mounted roof air conditioner; rubber mounted
cab glass; Cat machine security system Caterpillar product line; and front liftcylinder baffle
• Additional information in Waste Landfills Brochure (AEXQ0037)• Price List info: Order 938H Packages G (bottom protection 317-9489) and
H (top protection 317-9490), 302-7848 for 950/962H, 302-7849 for 966H,302-7850 for 972H, and 329-6630 for 980H.
68
Market Segment Application Offerings
Corrosion Resistance Arrangement (938H-962H)
• Corrosion package machines will be sourced out of CBL• Designed for corrosive environments such as fertilizer plants, chemical
industries, agriculture and salt water ports • Industry unique factory treatment• More protection of all machine components which can be affected by
corrosive materials• A four-stage special paint process provides a paint thickness which is more
than two times the thickness of the standard paint, giving the machine extraresistance against corrosion.
• Front hoses are treated with heat shrink tubing.• Silicon protection applied to electrical terminals and exposed bolts to
maximize component life.• Anodized metal accelerator pedal.• Heavy-duty 24V/95A sealed alternator. • Cooling cores receive a corrosion resistant treatment prior to assembly.
Corrosion resistant (e-coat) coating applied to engine, radiator, hydraulicoil cooler, transmission oil cooler, and air conditioner condenser cores.
69
InfoCast
For additional marketing information, including contacts, sales tools, currentproduct information and updates, please visit the InfoCast website at:https://nacd.cat.com/
InfoCast is a Caterpillar dealer extranet system.See your dealership IS coordinator if you don’t already have access.
To find information for all wheel loaders,click on “Product Information” in the left-hand menu.
For 924H-930H wheel loaders, click on “Building Construction Products”, then click “Small Wheel Loaders”.
For 938H-980H wheel loaders, click on “Medium Wheel Loaders”.
70
Marketing Contacts: 924H-930H
Nick NataleSWL Marketing(919) 465-5545
71
Marketing Contacts: 938H-980H
Bill CampbellProduct Application Specialist – MWLLarge Contractor [email protected](630) 859-4378
Arve OpperudProduct Application Specialist – MWLLarge Contractor [email protected](630) 859-6001
Don WeinholdProduct Application Specialist – MWLQuarry & Speciality [email protected](309) 675-4153
TEJB5042-07© March 2009
All Rights ReservedPrinted in U.S.A.
CAT, CATERPILLAR,SAFETY.CAT.COM, their respectivelogos, ACERT, “Caterpillar Yellow”and the POWER EDGE trade dress,
as well as corporate and productidentity used herein, are trademarks
of Caterpillar and may not beused without permission.