+ All Categories
Home > Documents > Cement Bond Log (CBL) Logging Services · Halliburton's Cement Bond Log tools reveal the...

Cement Bond Log (CBL) Logging Services · Halliburton's Cement Bond Log tools reveal the...

Date post: 25-Dec-2019
Category:
Upload: others
View: 35 times
Download: 2 times
Share this document with a friend
2
CEMENT EVALUATION Cement Bond Log (CBL) Services Accurate Cement Evaluation in any Downhole Environment Halliburton's Cement Bond Log tools reveal the effectiveness of cementing operations. Evaluate cement bond to both pipe and formation Indicate channels or intervals with only partial bond Locate free pipe and top of cement With more than 75 years of experience, Halliburton has the right tools and the superior on-site capabilities to provide reliable cement bond logs in any downhole environment. Full Suite of Tools Halliburton's array of nine different CBL tools produce accurate bond logs in any casing size – from 2 in. to 20 in. – over a wide range of temperatures and pressures. Bond Logs in Hostile and Slimhole Environments Haliburton's Hostile Full Wave Sonic tool can provide reliable bond data in temperatures up to 500°F and pressures as high as 25,000 psi. And with an OD of just 2.75 inches, the HFWS is also ideal for slimhole applications. Superior Wellsite Presentations Real-time results can be presented in a variety of formats to match specific wellsite operations. e wellsite engineer can switch between formats during logging for optimal viewing. e cement bond logs shown below utilize acoustic data to determine the degree of cement bonding to the pipe and formation. Primary log presentations include pipe amplitude curves in Track 2 and a Micro- Seismogram® (MSG) waveform in Track 4. Amplitude curves are used in the calculation of percent of bond to the pipe while the MSG reveals qualitative information on both the pipe and formation bond. Cement Bond Log (CBL) Logging Services Accurate Cement Evaluation In Any Downhole Environment HAL936 is cement bond log is across a section containing free pipe. e log exhibits a classic MSG signal of very straight lines with a casing collar pattern near the center of the log. e volumetric map shows approximately 97% liquid while the amplitude curve is reading between 60 and 70 mV, revealing that there is virtually no cement present in this interval. is cement bond log shows a fully bonded section. Note the low amplitude signals in track 2 (approximately 1 mV) and the absence of pipe signals in Track 4 of the MSG. e volumetric map in Track 3 shows 100% solid material except for a small section in the middle, where it is approximately 70% to 75% bonded. Formation signals in the MSG waveform indicate cement bond to the formation. SOLIDS LIQUIDS AMPLITUDE AMP/AMP GAMMA CCL EI TT MSG USEC -50000 0 100 260 160 0 250 CBL B/1 1 0 0 100 0 10 0 20 X700 50000 HAL935 SOLIDS LIQUIDS AMPLITUDE AMP/AMP GAMMA CCL EI TT MSG USEC -50000 0 100 260 160 0 250 CBL B/1 1 0 0 100 0 10 0 20 50000 X100
Transcript
Page 1: Cement Bond Log (CBL) Logging Services · Halliburton's Cement Bond Log tools reveal the effectiveness of cementing operations. • Evaluate cement bond to both pipe and formation

CEMENT EVALUATION

Cement Bond Log (CBL) ServicesAccurate Cement Evaluation in any Downhole Environment

Halliburton's Cement Bond Log tools reveal the effectivenessof cementing operations.

• Evaluate cement bond to both pipe and formation

• Indicate channels or intervals with only partial bond

• Locate free pipe and top of cement

With more than 75 years of experience, Halliburton has theright tools and the superior on-site capabilities to providereliable cement bond logs in any downhole environment.

Full Suite of Tools

Halliburton's array of nine different CBL tools produceaccurate bond logs in any casing size – from 2 in. to 20 in. –over a wide range of temperatures and pressures.

Bond Logs in Hostile and Slimhole

Environments

Haliburton's Hostile Full Wave Sonic tool can provide reliable bond data in temperatures up to 500°F and pressures as high as25,000 psi. And with an OD of just 2.75inches, the HFWS is also ideal forslimhole applications.

Superior Wellsite Presentations

Real-time results can be presented in avariety of formats to match specificwellsite operations. The wellsite engineercan switch between formats duringlogging for optimal viewing.

The cement bond logs shown belowutilize acoustic data to determine thedegree of cement bonding to the pipeand formation. Primary logpresentations include pipe amplitudecurves in Track 2 and a Micro-Seismogram® (MSG) waveform in Track 4. Amplitude curves are used inthe calculation of percent of bond tothe pipe while the MSG revealsqualitative information on both thepipe and formation bond.

Cement Bond Log (CBL) Logging ServicesAccurate Cement Evaluation In Any Downhole Environment

HA

L936

This cement bond log is across a section containing free pipe. The logexhibits a classic MSG signal of very straight lines with a casing collarpattern near the center of the log. The volumetric map showsapproximately 97% liquid while the amplitude curve is reading between 60 and 70 mV, revealing that there is virtually no cement present in this interval.

This cement bond log shows a fully bonded section. Note the low amplitude signals in track 2(approximately 1 mV) and the absence of pipe signals in Track 4 of the MSG. The volumetric mapin Track 3 shows 100% solid material except for a small section in the middle, where it isapproximately 70% to 75% bonded. Formation signals in the MSG waveform indicate cementbond to the formation.

SOLIDS

LIQUIDS

AMPLITUDE

AMP/AMPGAMMA

CCL

EI TT MSG

USEC

-50000

0 100

260 160 0 250CBL B/1

1 00 100

0 10

0 20

X700

50000

HA

L935

SOLIDS

LIQUIDS

AMPLITUDE

AMP/AMPGAMMA

CCL

EI TT MSG

USEC

-50000

0 100

260 160 0 250CBL B/1

1 00 100

0 10

0 20

50000

X100

Page 2: Cement Bond Log (CBL) Logging Services · Halliburton's Cement Bond Log tools reveal the effectiveness of cementing operations. • Evaluate cement bond to both pipe and formation

Cement Evaluation

CBL TOOLSCement Bond

LoggingTool (CBT-EA™)

Full Wave SonicTool (FWST-A™)

Hostile Full WaveSonic Tool (HFWS-A™)

Max Temperature

Max Pressure

Max ODRecommended Min Csg/Tbg ID

Recommended Max Csg/Tbg ID

LengthRecommended Logging Speed

350°F (177°C)

18,500 psi(127,600 kPa)

3.25 in (83 mm)

4 in (102 mm)

13.38 in (340 mm)

18.04 ft (5.50 m)

30 ft/min(9.1 m/min)

350°F (177°C)

20,000 psi(137,900 kPa)

3.63 in (92 mm)

4.13 in (105 mm)

20 in (508 mm)

20.41 ft (6.22 m)

30 ft/min(9.1 m/min)

500°F/6hr(260°C/6hr)

25,500 psi(172,400 kPa)

2.75 in (70 mm)

3.5 in (89 mm)

12 in (305 mm)

30.22 ft (9.21 m)

30 ft/min(9.1 m/min)

Halliburton's suite of CBL tools provide reliable bond logs in casing sizes from 2 in. to 20 in. These are 3 of the tools commonly used.


Recommended