1

Cement Presents

Materials Used Article Number QuantityJewellery Mould - Pendant Day, approx. 23 x 39mm, material requirements: approx. 8g Jewellery - Concrete 508863 1

Jewellery Mould - Pendant Heart, approx. 27 x 39mm, material requirements: approx. 7g Jewellery - Concrete 509423 1

Jewellery Mould - Pendant, approx. 25 x 39mm, material requirements: approx. 5g Jewellery - Concrete 508988 1

Fine Concrete for Jewellery, 500g 608792 as required

Fine Concrete for Jewellery, 3000g 608806 as required

Release Agents - Formestone, 100ml 480666 1

Sticker Feathers, black, 37 pieces, approx. 25 - 87 mm 307249 1

Deco & Lifestyle Hobby Paint, coffee cream, 230 ml 608345 1

Deco & Lifestyle Hobby Paint, antique gold, 230 ml 446712 1

Collier - Silky Cord, champagne, approx. 450 x 3 mm 575691 1

Collier - Silky Cord, black, approx. 450 x 3 mm 575680 1

Chain, approx. 1 m x 3 mm, copper 548034 1

Spacer Rings, 10 pieces, gold, ø 12 mm 206602 1

Spacer Rings, 20 pieces, copper, ø 6 mm 418126 1

Metal - Pendant - Mix, Leaf, Bird, Clover, set of 3, approx. 10 - 14 mm 593604 1

Recommended Materials/Tools:Jewellery Pliers - Set of 3 512509 1

Tools Neededsurface, measuring cup, mixing vessel, beater, vegetable oil (or release agent Formestone), kitchen roll, bristle brush, round brush, side cutter, round nose pliers, scissors

InstructionsS010K002

Cement Jewellery

2

Apply the silicone mould with release agent according to product description.Mix fine concrete with water according to product description.Fill the silicone mould with concrete and let it dry overnight.Then remove it from the mold.Let residual moisture escape.Dispense parts of the stickers-feathers off the release paper and press them on the concrete shapes.To bring out the main points, colour parts of the feathers with Deco & Lifestyle Hobby Paint.Let the paint dry.Insert and close a big golden spacer ring in the hole off each concrete pendant.Thread the desired Silky-Cord-Collier through one spacer ring.For a further collier, thread the copper coloured chain through a spacer ring.Shorten the cain if desired. Connect the beginning and the end of the chain with a copper spacer ring.Hook one of the golgen metal pendants (cloverleaf, bird, leaf) in two copper spacer rings.Hook this metal pendant in the golden spacer ring, of the pendant with the copper coloured chain.

Candle Holder Cement Style

Materials Used Article Number QuantityWood Candle Holder, approx. 80 x 80 x 220 mm 947986 1

Wood Candle Holder, approx. 80 x 80 x 270 mm 947975 1

Sculpey® Silicon Mould Cabochon, approx. 96 x 125 x 12 mm 442752 1

Fine Concrete for Jewellery, 500g 608792 1

Release Agents - Formestone 100ml 480666 1

Raffia Natural, 20g 530497 1

Creative Set - Concrete Effect, 7 pieces 607811 1

Deco & Lifestyle Hobby Paint , light grey green, 230 ml 446295 1

Deco & Lifestyle Hobby Paint , yellow, 230 ml 608378 1

Deco & Lifestyle Hobby Paint , coffee cream, 230 ml 608345 1

Deco & Lifestyle Hobby Paint, antique gold, 230 ml 446712 1

Tools Neededsurface, measuring cup, mixing vessel, beater, vegetable oil (or release agent Formestone),kitchen roll, round brush, bristle brush, scissors, hot glue gun

3

Apply the silicone mould with release agent according to product description.Mix fine concrete with water according to product description.Fill the silicone mould with concrete and let it dry overnight.Then remove it from the mold.Let residual moisture escape.Paint the candle holder with Concrete Effect (proceed as described in the product description).Colour it with different colours of Deco & Lifestyle Hobby Paint.Thread the concrete-jewellery-pendant Rings (made of silicone mold Cabochon) on bast and fasten them on the big candle holder.Glue the round concrete-jewellery-pendants with the hot glue gun to the small candle holder.

S010L002

Have fun creating! Your Opitec Creative Team!