Cement - Mortar 50E009 Blaine air permeability (fineness), apparatus Standards EN 196/6 - ASTM C204 - AASHTO T153, BS 4359/2 -UNI 7374 - NF P15:442 -UNE 80106To determine the fineness of Portland cement in terms of the specific surface expressed as total surface area in square centimeters per gram of cement. The apparatus is supplied with glass U-tube manometer with valve, steel stand, test cell with disk and plunger all in stainless steel, rubber aspirator bulb, 1000 filter paper discs, manometric liquid, thermometer. Weight 12 kg.E010-02 Standard reference cement

114p to ASTM / SRM/EN to calibrate the Blaine E055-08 Glass thermometer –10/+50ºC

E014 Le Chatelier flaskEN 196/3 -ASTM C188, AASHTO T133, UNE 83453 To determine the relative density (specific gravity) of hydraulic cement and lime. Capacity 250 ml. The neck is graduated from 0 to 1 ml and from 18 to 24 ml with divisions of 0.1 ml. Weight 500g.

E016 Water flowing sieves device Standard D.M.3/6/68To determine the fineness of cement. It consists of a sprying unit with feed cock and gauge, brass sieve body 0 85 mm and 95 mm high with two stainless steel cloth discs having opening 0.18 and 0.09 mm. A cement sample of 25 g is placed inside the sieve and washed for two minutes by means of the spraying unit put on top of the sieve. The residue of the retained cement is obtained by drying the sieve at 110°C. Weight 3 kg.

E017 Fineness of fly ash by wet sieving Standards EN 451:2 -ASTM D430The set brass made consists of sieve ∅ 50 mm with stainless steel mesh opening 0.045 mm, spray nozzle 17.5 mm ID with 17 holes ∅ 0.5 mm, pressure gauge ∅ 80 mm, range 0 -160 kPa, div. 5 kPa, fittings and connectors. Weight 3 kg.

E020 Bulk cement samplerStandards ASTM C183 -AASHTO T127 EN 196/7To sample cement in bulk storages or shipment. Made of brass, it consists of two cocentric tubes with slots. Inside tube volume 3 liters, dimensions ∅ 40x1500 mm.

E021 Packaged cement tube samplerStandards ASTM C183 - AASHTO T127 - EN 196/7 Used to sample cement homogeneously from cement bags, dimensions ∅ 32 x 700 mm. Weight 2 kg.

E025 Bulk density of cementThis apparatus is used for the measurement of the apparent density (bulk density) of powders and non-cohesive materials. It consists of sieve funnel with tripod, unit weight measure 1 liter capacity with hopper, spatula, straight edge, large spoon, dimensions ∅ 350x520 mm. Weight 6 kg.

E009

E014

E016

E017

E021

E020

E025

Cement - Mortar 51E027 Air entrainment meter, capacity 1 liter , EN 459-2Cast aluminium made, the test pot and the upper part are airtight sealed. The whole is connected to a dial gauge indicating directly the air entrainment in percentage, with range 0-50%. With built-in air pump, dimensions Ø 200x320 mm, weight 4 kg.

E027-01 Air entrainment meter, capacity 0.75 l, EN 413-2 Same as E027 but capacity 0.75 l.

E028 Air entrainment meter, capacity 1 l, EN 459-2Same as model E027 but with incorporated an electric mini-compressor giving air pressure and keeping it constant all along the test, 220/2 40 V 50 Hz. Weight 6 kg.E028-02 Air entrainment meter, capacity 0.75 l, EN 413-2Same as E028 but capacity 0.75 l.

E028-01 Filling hopper for the air entrainment meters E027 and E028.

Air content of freshly mixed mortars by the density method.

E029 Measurer 400 ml capacityStandards ASTM C185 - 85 - AASHTO T137Steel made, internal ∅ 76.2 x 88.1 mm height

E030 Measurer 500 ml capacityStandard BS 4551Steel made, internal ∅ 76x110 mm height.

E030-01 Hard plastic tamper ∅ 37.5 ± 0.5 mm. Weight 250 g. E055-07 Glass plate, nominally ∅ 120 mm V192-08 Chattaway spatula

E031 Dropping ball apparatus Standards BS 4551-1,6463 -4To measure the consistency of cement mortars, this instrument allows an acrylic ball ∅ 25 mm to fall freely from a standard height of 250 mm into a specimen of mortar contained into a mould and the surface of which has been carefully prepared. The depth of the ball penetration into the mortar gives the specimen consistency. The instrument comprises a dropping device mounted on a stand, acrylic ball, mould ∅ 100x25 mm. The base of the stand is machined. Chromed finishing. Weight 8 kg.

E031-01 Ball penetration measuring deviceFormed by a tripod on which a dial gauge 25x0.01 mm is mounted. A device to adjust the height of the dial in relation to the tripod is also included. Chromed finishing.

E037 Marsh funnel viscometerFor viscosity determination on drilling muds and fluid materials. Orifice opening 4.7 mm. Half part of the funnel mouth is foreseen of sieving cloth, 2 mm mesh. Plastic break-resistant made. Supplied with graduated cup. Weight 1 kg.

E027

E028

E030

E029

E030-01

E055-07

E031

E031-01

E037

Cement - Mortar 52E037-01 Baroid mud balanceIt provides a simple method for the accurate determination of mud density with the advantage that the temperature of the drilling mud does not materially affect the accuracy of readings. The balance consists of a base and graduated arm with cup, lid, knife edge, rider, built-in spirit level and counter-weight, carrying case. The constant volume cup is affixed to one end of the graduate arm and the counterweight on the opposite end. Weight 5 kg.

E038 Flow cone apparatus Standard EN 445For viscosity and fluidity determinations of mor- tars, muds, grouts, fluid materials etc. Cone top ∅ is 155 mm, total length 290 mm, capacity 2000 cc. Mortar fluidity is considered suitable when the flow time of 1000 cc of mortar is comprised between 17 to 25 seconds. Entirely brass made, it is supplied with four interchangeable nozzles Ø 8-9-10-11 mm, stand adjustable in height, plastic graduated cup. Weight 10 kg.

E038-01 Interchangeable nozzle Ø 12.5 mm for the flow cone E038

E039 Water retention apparatus Standards ASTM C91,C110To determine the density of mansory cement and lime putty so obtain a yield volume value. The unit comprises a water aspirator, mercury column, manometer, three-way stop-cock, metal perforated dish, glass funnel, stand, mercury valve, pack of paper filter disc, 1 kg of mercury, accessories but without pump which must be ordered separately, dimensions 500x280x600 mm. Weight 8 kg.

V203 Vacum pump220-240 V, 1ph, 50 Hz.

E037-01

E038

E039

V203

Cement - Mortar 53E044 Automatic computerized VICAT recording apparatus “VICATRONIC”To determine the initial and final setting time of an hydraulic binder, this electronic recording unit performs the complete test cycle in a totally automatic system ensuring results of absolute precision and repeatability. The results are printed on the integrated printer. Large high contrast LCD display showing the test dates together with general functions, real time graphic. Standard programmes for tests according to standards as EN 196/3, ASTM C191, DIN 1664, DIN 1168 gypsum, NF P 15/431. Further programs can be developed using the specific menu “free tests”.

The mobile probe weighs 300 g (1000g following EN, NF standards) the penetration needles has 1.13 mm diameter (1 mm ASTM standard). Its fall can be programmed in free fall or in guided fall. Totally flexible as far as time is concerned, penetration time can be set between 0.5 min and 999 minutes or can be changed during test up to 5 different phases with different interval times.

The Vicatronic calculates, visualizes and prints: time from the moment of sample preparation, starting time, residual time to the next penetration, residual time to the end of the test, number of penetrations made and the residual penetrations to be made. All parameters and results are memorized. USB connection port for separate printer with standard format., RS232 port for connecting a PC.

Supplied with incorporated printer, two needles ( 1 mm/1.13 mm) two conical moulds EN and ASTM, glass plate. 220 V, 220-240 V, 1 Ph, 50 Hz, 50 W, dimensions 400x200xh470 mm, weight 13 kg

E044-11 Software “VICAT-WIN” with connection cable of 3 m that allows by the RS223 port downloading processing, printing and managing all the data directly from the PC.

E044-20 Thermostatic water heating/cooling systemThis device produces water at controlled temperature of 20±1°C and circulated into the tank E044 by ensuring the test execution at saturated humidity and controlled temperature, as requested by EN 196-3 standards, 220/240 V, Hz, 1150 W, dimensions 615x375x400 mm, weight 24 kg.

AccessoriesE043 Mould tank

For testing in water of the specimen. E042 Needle for final setting EN / BS Ø 1.13 mmE042-01 Needle for final setting ASTM Ø 1.0 mmE042-02 Consistency probe dia. 10x50 mmE044-30 Needle cleaning deviceE044-41 Probe 100 g to make test on gypsum DIN 1168E044-45 Additional 700 g weight (NF, EN)E046-03 Hardened 1.13 mm needle, EN, UNI, NF, DIN, BSE055-04 Plastic mould Ø 80/90 x 40 mm, UNIE055-11 Brass mould Ø 80/90x40 mm, BSE055-12 Split brass mould two halves Ø 80/90x40 mm, BSE055-13 Plastic mould Ø 65/75 x40 mm, DIN

E044

E044-20

E044-11

E042 –E055-13

Cement – Mortar 54E055 Vicat apparatus used for setting time and consistency Standards EN 196:3 - ASTM C187, C191 -AASHTO T129, T131 - DIN 1164 - BS 4550 - NF P15 - 414 -D.M.3 / 6/68 The instrument consists of a metallic frame, graduated scale with index, sliding probe of 300 g, consistency plunger Ø 10 mm, glass base plate, thermometer. (The needle and conical mould are not included and have to be ordered separately, see accessories), dimensions 160x200x300 mm.

E042 Final needle ∅ 1.13 mm EN-NF - BS - DINE042-01 Final needle ∅ 1.00 mm ASTM - AASHTOE046 Needle ∅ 1.13 mm EN-UNI-NF-DIN-BS E046-01 Needle ∅ 1.00 mm ASTM – AASHTOE046-03 Hardened needle ∅ 1.13 mm EN – BS - NFE055-06 Additional weight 700 g NF/ENE055-08 Glass thermometer –10 to +50ºCConical moulds for all standards available

E058 Gillmore apparatus, ASTM C91, C141, C266Used to determine the setting time of cement. Vertical support shaft with device to maintain the horizontal arms in alignment. Support assembly adjustable. Two calibrated steel weights needles. Initial setting needle ∅ 2.12 mm, weight 113 g, final setting needle ∅ 1.06 mm, weight 453.6 g.E059 Funnel grooveStandard UNI 8997To determine the consistency of the expansion premixed cement mortars for anchorages, mixed with water, classified of super-fluid type, weight 20 kg.

E060 Bridge of dual measure, formed by a steel square straight edge with two adjustable measure screws E060-01 Fix caliper at two steps, heights 100 and 107 mm E060-02 Metallic container, hermetic cover ∅ 99x116 mm

E061 CalorimeterUsed to determine the heat of hydration of cement by the solution method. The apparatus consists of a dewar flask which is housed in an insulated wooden box, constant speed electric stirrer, Beckmann centesimal thermometer and funnel pouring the cement. The wooden box is hinged so that the flask can be easily removed or replaced. 220/240 V, 50 Hz, 150 W, dimensions 35x25x65 mm, weight 15 kg.E061-11 Propeller to ASTM C196 standardE061-12 Propeller to EN 196-8 standardE063 Flame photometerStandards EN 196:21 - ASTM C114:17 - BS 4550To determine the alkali content of cement, supplied with sodium (Na) and potassion (K) filters, fuel and air connections, accessories, digital readout 0-199,9 ppm , reading range K or Na 3 - 100 ppm, sensibility 3 ppm, reproductibility 1% coefficient of variation for 20 consecutive samples, operates on propane, butane, natural gas supplies. Air supply 6 liter/min. with pressure of 1 kg/cm2. 220/240 V, 50Hz dimenions 420x360x300 m, weight 8 kg. E063-01 Lithium (Li) filter E063-02 Barium (Ba) filterE063-03 Calcium (Ca) filter E063-04 Natural gas regulator E063-05 Propane gas regulator E063-06 Butane gas regulator

E055

E058

E059

E061

E063

E060

Cement - Mortar 55Le Chatelier equipment for soundness of cementEN 196/3-BS 6463-NF P15-432-UNE 80102 – D.M. 3/6/68E064 Le Chatelier water bathInside stainless steel chamber and exterior in painted steel sheet, it can hold up to 12 Le Chatelier moulds in the removable rack. The bath reaches the boiling point in approx. 30 minutes. Now a device keeps the bath temperature at the boiling point. Le Chatelier moulds remain covered by the water during all the test execution. 220 V, 50/60 Hz, 1800 W, dim. 405x265x50mm, weight 7 kg. E065 Le Chatelier mouldSame to mod. E066 but with serial number for identificationE066 Le Chatelier mouldMade from a brass spring tensioned split cylinder having internal ∅ 30x30 mm high, with two pointers 150 mm long, chromed finishing.E066-01 Glass plate 50x50 mm, pack of 2 pieces E066-02 Weight of 100 gE066-03 Extensibility of mould apparatusE067 Craking test mouldStandard NF P15 - 434Used to produce ring-shaped specimens.

E070 Autoclave for soundnessStandards ASTM C151, C141 - D.M.3 /6 / 68 - UNE 7207 It consists of a high pressure boiler made from special alloy steel, inside ∅ 154x430 mm high, receiving a holding rack for 10 cement specimens. The heating system is achieved by electric resistances. The control unit encloses a pressure gauge with built in pressure regulator and power switches. Supplied with safety valves. 220/240 V, 50/60 Hz, 3500 W, 295 psi, dim. 450x475x1080 mm, weight 75 kg. E071 Autoclavebasically similar to mod. E070, capacity 8 liters, max. pressure 25 bar (2.5N/mm2), temperature max. 250°C.

Moulds for expansion, soundness and shrinkage tests

E072 Two compartment prism mould 25x25x250 mm With 4 steel inserts, weight 6 kg. Standard ASTM C490E073 Two compartment prism mould 75x75x254 mm With 4 steel inserts, weight 9 kg. Standard BS 1881, 6073E074 Three compartments prism mould 40x40x160 mmMade of Cr/Ni steel, hardness 60 HRC. All surfaces are grinded, with tolerances within 0.1 mm, with 6 inserts, weight 12.5 kg. UNI 6687 - ASTM C348E107 Three compartments prism mould 40x40xl60 mmSteel made 55 HRB, with 6 inserts. Standards NF P15 - 434 - DIN 1164E113 Three compartments prism mould 70x70x280 mmSteel made 55 HRB, with 6 inserts. Standard NF P18-427

E064

E066-03, E066-02, E066-01

E065E066

E067

E070

E071

E073

E072

E113

E074

E107

Cement - Mortar 56E077 Length comparatorStandards ASTM C151, C490 - NF P15-433, P18-427 - BS 1881, 6073 - D.M.3 /6 /68 - DIN 1164, UNI 8147, 8148, 6687 To measure the length variations of 25x25x250 mm cement specimens in autoclave soundness tests. It can also be used to measure linear shrinkage of specimens 40x40x160 mm, 70x70x280 mm, 50x50x250 and 80x80x240 mm. The unit comprises a steel frame with an adjustable height beam fitted with a dial gauge 5 mm travel x 0.001 mm divisions. Supplied without reference rod. Dimensions ∅ 180x450 mm, 10 kg.

E078-01 Reference rod for 25x25x250 and 75x75x254 mm specimens to ASTM C490 and BS 1881E078-02 Reference rod for 40x40x160 mm ASTM C348E078-03 Reference rod for 70x70x280 mm to NF P18 - 427E078-04 Reference rod for 40x40x160 mm to NF P15 - 433E078-05 Reference rod for 50x50x250 mm UNI 8148 and 80x80x240 mm UNI 8147 specimens

E079 Length comparatorIdentical to mod. E078 but with digital gauge stroke 25 mm and sensitivity 0.001 mm, with battery and RS 232.

E080 Plaster extensometerStandards UNI 6782 -BS 1191 To measure the linear expansion of a paste of standard consistence. It comprises an horizontal cradle 100 mm long x 600 mm wide x 25 mm deep closed at one end and open to the other. The open end is in contact with a dial gauge spindle, so that the lateral expansion of the specimen is measured. The dial gauge has 10 mm travel and 0.01 mm graduation, dimensions 250x80x80 mm , weight 3 kg.

E081 Mortar workability apparatus NF18-452, EN413/2 To test concrete mortar for dynamic workability and also to ensure optimum proportioning of mortar constituents (sand, water, cement, as well as cement/sand and water/cement ratios). Consists of a prismatic receiver divided into two unequal volumes by a removable partition and by an electric vibrator. The fresh mortar is poured in the large volume place, the separating partition is removed and the vibrator starts automatically. The mortar flows from the large volume to the small one, in a time which is a function of the workability of the mortar. 220 V, 50 Hz, 110 W, weight 18 kg.E082 Pat test, standards BS 1191 - 6464:4 – EN 459/1For determination of the soundness of hydrated lime, gypsum and building plasters. Brass ring mould ∅ 100x5 mm deep. With glass plate.E083 Plunger penetration apparatusStandards EN 413/1, 459/2 - DIN 4211Used to determine the consistency of fresh mortar, lime and masonry cement. The base is foreseen of a device to locate the test cup. The height of the drop can be accurately adjusted to 100 mm, with test cup and tamper, dimensions 200x200x700 mm, weight 8 kg.E091 Bulk density of lime, EN 459/2 - DIN 1060The apparatus allows a sample to fall from a known height into a volumetric container, consisting of a hopper, one liter cylindrical container and spring loaded trap, weigh 5 kg.

E077+S375+E078-01

E080

E081

E082

E083 E091

E077+S383+E078-02

Cement - Mortar 57

Flow tables for flow and workability tests of mortar and limeStandards ASTM C230 - BS 4551:1 - EN 459 / 2 -UNI 7044 -NF P18 - 585 - DIN 1060 -UNE 7205, 83258

- To perform this test, a specimen contained in a cone mould is placed on a metal surface which is then raised andTo perform this test, a specimen contained in a cone mould is placed on a metal surface which is then raised and dropped from a known height, after releasing the specimen from the mould. The equipment consists of a circular top table with spindle, bronze flow mould and tamper. The apparatuses to EN and DIN standards are equipped also with filling hopper. Motorized models foresee an automatic digital drop counter. 220/240 V, 50 Hz, 150 W, weight 20-50 kg.

Models Standard Hand Table Drop Spare Spareoperated motorized Ø mm height mm mould

E084 UNI7044 • 300 10 E085-05 E085-06E085 UNI7044 • 300 10 E085-05 E085-06E086 ASTM C230 • 254 12.7 E087-05

E087-06E087 ASTM C230/BS4551 • 254 12.7 E087-05

E087-06E088-01 NF P18-585 • 250 20 E088-07

E087-01Flow calliper to ASTM and BS standards for measuring the Ø of the sample, weight 450 g.

E090 E085 E087

Cement – Mortar 58

E092 Automatic programmable mortar mixerStandards EN 196/1, E196 / 3, 413/2, 459/2 - ASTM C305 - AASHTO T162 -BS 3892 -NF P15 - 413 -DIN 1164Sturdy and durable construction, planetary transmission , automatic sand dispenser, variable speed inverter, transparent protection of mixing area, stainless steel polished mixing bowl and beater, different automatic programmable mixing cycles conforming to standards, large LCD display. 220 V, 50 Hz, weight 80 kgE092-06 Dispenser for the introduction of water during the mixing phaseE092-10 Bowl, polished stainless steel, 4.7 l capacityE095-04 Beater, polished stainless steelE093 Automatic mortar mixerFor the efficient mixing of cement pastes and mortar with three automatic sequence of mixing cycles, bowl capacity is 4.7 liters. Two speeds can be selected 140 or 285 rpm for the revolving action, 62 or 125 rpm for the planetary action. It is possible to select the manual working or one of the three automatic programs. By operating automatically on changes of speed, stops and mixing sequences, outlined by acoustic signal, the unit performs the mixing cycle. Equipped of an automatic sand dispenser which fills the sand into the mixing bowl for a period of 30 seconds (only EN 196 / 1 program), with safety door conforming to 89/392 /CEE directive; if opened, it automatically stops the machine. With stainless steel bowl but without beater which has to be ordered separately, 220/240 V 50 Hz, dimensions 340x460x700 mm, weight 45 kg.

E094 Mortar mixerBasically similar to model E093, but not equipped without automatic program, sand dispenser and safety door. Dimensions 340x460x500 mm , weight 40 kg.

E095 Mortar mixerBasically similar to model E094, but with safety door to 89 / 392 CE directive. Dimensions 340x460x500 mm, weight 44 kg.

AccessoriesE095-01 Stainless steel bowlE095-02 Aluminium beater with bayonet fittings E095-03 Stainless steel beater with bayonet fittings, to EN 196/1. E095-04 Stainless steel beater with bayonet fittings to EN 196/1. The beater is polished to eliminate porosity.E097 Reference sand, size 0.08-2 mm, EN 196/1, bag of 1350 g.

E100 Three compartments mould for prisms 40x40x160 mmStandards UNI 6009 - UNE 80101, 83258Made of Cr/Ni steel, hardness 60 HRC. With base, stop lever and safety catch to avoid disengagement during the jolting operation. All parts are marked with identification number for a correct assembling, surfaces are grinded and tolerance is held within 0.1 mm as requested by standards, weight 12.5 kg.

E106 Feed hopperTo fill the mould E100, E102, E103 when it is mounted on the jolting machine E130. Cast aluminium made, weight 1 kg

E093

E092

E095-01

E097

E095-02 E095-03

E100

E101

Cement – Mortar 59E102 Three compartments mould 40.1x40x160 mmEN 196/1Steel made with hardness over HV 200.All surfaces are grinded and all parts are marked with an identification number for a correct assembling. Supplied without certificate of conformity, weight 10 kg.E102-01 Feed hopper, used to fill the mould E102 and E102-02 Large and small scraper to EN 196/1 S200-11 Straight edge 300 mm long, one cutting rim E102-03 Glass plate 220x190x6 mm

E103 Three compartments 40.1x40x160 mmEN 196/1Steel made, with hardness of inside walls over 500 HV. All parts are marked with an identification number for a correct assembling. Each mould is individually verified in the dimensional tolerances, hardness, squareness, flatness and roughness with instruments periodically certified by Namas center or equivalent, with certificate of conformity, weight 10 kg.E103-02 Three gang mould 40.1x40x160 mmSame as E103 but supplied with a certificate of official organization like Namas or equivalent.

E105 Three compartments mould 40x40x160 mmNF P15 - 413 - ASTM C348 IN 1164, 1060Steel made, hardness 55 HRB, E106 Feed hopper

E108 Briquette mould, three compartments ASTM C190, C307 - AASHTO T132E111 Briquette mould, 1 compartmentASTM C190, C307 - AASHTO T132Accurately machines, easily collapsible, with base.

E110 Three compartments cube mould 50 mmASTM C109 - AASHTO T106Steel, hardness 55 HRB, it can be also used for soil and other materials.

E130 Jolting apparatusStandards EN 196/1 - NF P15-413 - ISO 679 - BS 3892 - UNE 80101To compact cement mortar prisms 40x40xl60 mm in the three compartments mould. It consists of a table holding the mould, seated on a rotating cam driven at 60 revolutions per minute. With separate control panel including main switch, automatic digital drop counter start/ top push button. 220/240 V, 50 Hz, 500 W. Dimensions 100x380x420 cm, weight 65 kg.

E132 Vibrating machine for 70.7 mm cube moulds Standard BS 4550The mould is mounted on a vibration platform with excentric mechanism. With guard, and a starter control mounted on a rigid frame. 220V, 50, Hz, 250 W, 100 kg.E133 Cube mould 70.7 mm, BS 4550Steel made with base plate.

E102-01

E102 E102-02

S200-11

E112

E105 E106

E133

E110

E108E111

E132

E130

Cement – Mortar 60E134-E134-02 Thermostatic bench cabinet, for curing cement, mortar, concrete specimensEN 196/1-ASTM C109, C511-BS 1881:111 - NF P18-404 For curing specimens at controlled temperature both at 95% relative humidity and in water by using suitable containers. Temperature range from +10 to 40°C, ±1°C sensitivity. Relative humidity 100%.The cabinet is entirely manufactured with stainless steel 18 /10. The refrigerator group and capacitors are housed in a separate compartment and mounted on sliders for an easy and simple maintenance. The insulation is obtained by a 60 mm thick material. Temperature is selected through an electronic digital thermostat. An original vaporization system creates 100% relative humidity. The upper side of the cabinet can be used as a working table.The compartments are equipped with three sliding grids dimensions of 325x600 mm. 220/240V, l ph.

E134-11 Plastic pan 24x30x7 cm.It accepts up to 6 prisms 4x4x16 cm for curing in water.

E136 Water curing bathTemperature range from ambient to +99°C with accuracy of 0.4°C at 20°C. The bath is equipped with a cooling coil device to be connected to the water net. Outside dimensions 680x420x 420 mm, weight 28 kg.

E136/B052-02 Water curing bath with cooling deviceIdentical to E136 but with cooling device placed under the bath. Dimensions 68x42x95 cm, weight, 60 kg.

E136-10 Mercury control thermometer range 0-50°C. division 0.5°C.

E138 Large capacity curing cabinetEN 196/1 - ASTM C87, C109, C190, C191 - UNE 80102 For curing large quantities of mortar and concrete specimens. Aluminum and polycarbonate made, it is complete with water circulating pump, precision digital thermostat and four shelves. Humidity range 95% to saturation. Temperature range from ambient to +30°C, accuracy ±1°C. Inside dim. 1090x470x1200 mm, overall dimensions 1370x540x 490 mm. 220/240 V, 50 Hz, 2000 W, weight 100 kg.

E139 Curing cabinetStandards EN 196/1 - ASTM C87, C109, C190, C191 Both external and internal walls are stainless steel made and insulated by a 50 mm thick glass wool.The cabinet has an inner inspection glass door. Temperature range from ambient to 70°C, humidity range 95% to saturation. 220V, 50/60 Hz, 1000W. Inside dimensions 620x44Ox400 mm, overall dimensions 900x 700x800 mm, weight 60 kg.

Mod. CapacityLiters

Compart-ments

Dimensionscm

Weights Watts

E134 260 2 149x70x80 140 400E134-01 400 3 194x70x85 175 500E134-02 550 4 240x70x85 210 500

E134

E136

E138

E139

Cement – Mortar 61Pull-off, bond strength1542 - BS 1881:207 - ISO 4624 - NF P18-853This dynamometer provides you with information on both the adhesive force and the tensile strength of two layers of materials: lime, facing plasters, mortars, building plasters, cements, concrete and resistance of anchoring studs. Compact, light, stand-alone. Load is applied by turning the crank. The reading is achieved through the indicator’s pointer which becomes blocked at the peak level of the testing. Models of different capacities are available and adhesion metal discs having Ø 20 and 50 mm can be used, depending to the expected pull force. The instrument is supplied without accessories to be ordered separately. To carry out the test a common electric drill is required. Weight 3.5 kg

E142-02 Pull-off tester 5 kN capacityrecommended for cement and plasters

E142-03 Pull-off tester 16 kN capacityrecommended for concrete

E142-04 Pull-off tester 25 kN capacityrecommended for concrete

E142-05 Pull-off tester 50 kN capacityrecommended for concrete

Accessories:E143 Adhesion metal disc Ø 20 mm (pack of 10 pcs.)E143-01 Adhesion metal disc Ø 50 mm (pack of 10 pcs.)E143-02 Tungsten carbide bit Ø 20 mmE143-03 Tungsten carbide bit Ø 50 mmE143-04 Adhesive metolux glue, can of 1 kgE143-06 Metallic carbide bit Ø 20 mmE143-07 Metallic carbide bit Ø 50 mm

Procedure of use1. Using the bit, make a round notch to the dimensions of the disc, up to the base material. This is intended to define exactly the testing surface. 2. Stick over the surface to be tested a disc of the relevant diameter. This is achieved using the adhesive metolux glue.3. The test consists in pulling out the notched part with the instrument. The result is provided in kN.

E142-02

E142-03

Cement – Mortar 62Compression and flexural testing machines for cement, bricks, rock, refractories etc. Standards EN 196 / 1 - BS 3892 - ASTM C109 - NF P18 - 411 - DIN 1164 -UNE 80101 - AS 2350For compression tests on cubes side 40, 50, 70, 100 mm, cores with max height 180 mm and flexural tests on prisms 40x40xl60 mm by using suitable devices. Max. vertical light between platens 185 mm. Ram travel 50 mm, platen ∅ 153 mm, gauges ∅ 200 mm, range 0-300 kN, division 2.5 kN, 0-50 kN, division 0.5 kN. Precision and repeatability ±1% of applied load. 220/240 V, 50 Hz, 750 W (motorized models), weights 300-330 kg. E155 Capacity 300 kN motorized, one gaugeWith power control electric pump and flow control valve. E156 Capacity 300 kN motorized, two gauges0-300 kN and 0-50 kN.E159 Capacity 500 kN, motorized with electronic digital measuring system Cybertronic. E159-01 Capacity 250 kN, motorized with electronic digital measuring system Cybertronic.E160 Dual range 500 kN/15 kN, motorized with electronic digital measuring system Cybertronic. Two pressure transducers for two measuring ranges 0-500 kN and 0-15 kN recommended for compression tests (by utilizing the range 0-500 kN) and flexural tests on prism 40,1x40x 60 mm ( by utilizing range 0-15 kN ). E160-01 Dual range, same as mod. E160 but with measuring ranges of 0-250 kN and 0-15 kN.E161 Capacity 250 kN, motorizedConnected to the automatic servocontrolled console Servotronic. It provides fully automatic testing through all test phases, with automatic control of load and pace rate and print out results and certificates. Compression/flexural devices to be positioned between the compression platens of the machine.E161-01 Dual range machine, 250/15 kNSame as E161 but with dual rangeE163 Software UTM2 for compression testsE164 Software UTM for flexion testsE164 Software UTM 2 for compression/flexion tests

E170 Compression device for prism of 40.1x40xl60 mm prism broken in flexure. Standards EN 196 / 01 - ASTM C349 - NF P15 - 451 Hardness of plates 60 HRC and upper platen is seat ball assembled. Cadmium plated for rust protection. E170-01 Compression device identical as E170but platen 40x62.5 mm DIN 1164, weight 12 kg. E171 Compression device for cube 50 mm side E171-01 Compression device for cube 70.7 mm side E172-01 Flexure device for 40.1x40x160 mm prisms. Upper bearer is seat ball assembled. The distance between lower bearers is 100 mm and one of themhas a spherical seat. Cadmium plated against rust.E172-02 Flexure device for 40x40x160 mm prisms Identical to model E172-01 but lower bearers have distance of 119 mm as requested by ASTM , 8 kg.

E156+E170

E159+C120+E170

E161+E172-01

E170

E171-01

E171

E171-01

E172-01

Cement – Mortar 63Compression/flexural testing machinesStandards EN 196/1 - ASTM C109 - BS 3892 - DIN 1164 - NF P18-411 - UNE 80101 - AS 2350

E181 Compression/flexural testing machine 250/15 kNFor 40.1x40x160 mm prismsDual loading chamber compression and flexure, max. capacity load in compression 250 kN, max. capacity load in flexure 15 kN. Piston strokes 50 mm. Dual loading chamber, ranges 250 kN and 15 kN by utilizing the digital measuring system Cybertronic C109. Load is measured by two electric strain cells. Accuracy and repeatability ±1%. 220/240 V, 50 Hz, 750 W. Dimensions 700x400x450 mm, weight 250 kg.

E183 Compressior/flexural testing machine 250/15 kNFor 40.1x40x160 mm prisms.Identical to mod. E181-01 but connected to the automatic servo-controlled unit Servotronic C104. It performs a fully automatic test procedure including speed rate and software for certificate printing.

C127 Graphic Printer A4 on thermal paperFor Cybertronic digital display unit

C128 Table printer, size A4

E163 Software UTM2 for compression testsFor managing and remoter control from a PC, according EN 196.1, ASTM C109E164 Software UTM2 for compression testsFor managing and remoter control from a PC according EN 196.1, ASTM C109C123 Software UTM 2 for Servotronic C104 unitFor managing and remote control through PC for compression and flexure tests (E1Compression/flexural devicesE170, E170-01, E171, E171-01, E172-01 and E172-02 have to be ordered separately.Technical features of software UTM21. Automatic identification of the machine connected.2. Setting of the sequence of operations of the test to be

made, settable by the operator, realisation of a personalised testing profile.

3. Memorisation of the test in the database with the possibility to process it again.

4. By means of a PC connected by a serial port RS232 to the machine, it allows interacting, test processing, graph and test report constructing and many other possibilities of remote control.

5. It allows visualising the instant loads, instant deformation, load/deformations/stroke graph, remote control of main functions of the machine. It calculates and saves all parameters of the test made.

6. The Windows menu allows to create personalised test profiles.

7. The test dates can be commented by means of test titles.8. The user can select the calculation algorithms and the

software will process required by the standards.9. The colours and the graph scales can be freely selected.

E181-01+C127+E170+E172-01+H009+C109-10

E183+E170+E172-01+H009+C123

Software E163, E164, C123

C128