page 27

Saving you Time, Saving you Money, Putting you First!

For more information, please call 604.572.4419 or visit www.superiortray.com

CENTER HUNG TRAY INTRODUCTION Easy step 1, 2, 3 connections for fast and effective

site installation: Step 1 - insert rod in splice

Step 2 - connect center section to splice

Step 3 - slide together TECHNICAL DATA Depth 6 to 24 inches. Length 10 feet (120″) standard. Fill Depth 3, 4 and 6 inches. Rung Spacing 3, 6, 9, 12 and 18 inches. Materials Aluminum Alloy 6061-T6, 6063-T6.

CATALOG NUMBER

A 1 2 L 4 – 1 2 – 1 2 0Material

Rung Space

Style(Prefix)

WidthLength in

Inches

Depth

Style: • T = Center Hung Top Mount Rung • WT = Wall Mount Top Rung Single Tier • L = Center Hung Bottom Mount Rung • WL = Wall Mount Bottom Rung Single Tier

For an integrated wire management system, Center Hung Tray simplifies the support and routing of power and telecom/teledata cabling. A single hanger rod is used at each support point. This makes installation easier by reducing support requirements and eliminating the need to pull cable through the trapeze supports. Center Hung provides substantial savings in cost and time. With Center Hung Tray, cables can be laid in on both sides. Both the support and connection of the Center Hung Tray sections are accomplished by a single splice coupling designed to save time. If additional support is needed beyond the 10 feet or 3 meter intervals, an intermediate support hanger can be used. Center Hung Tray rungs come already attached transversely through either the top or bottom of the center tubular rail. Each rung is securely staked to the center rail in four places, providing additional strength and rigidity for reliable cable support. The chances for damaging and losing rungs during transportation and cable installation are significantly reduced with this safe, reliable and secure method of rung attachment.

page 28

Saving you Time, Saving you Money, Putting you First!

For more information, please call 604.572.4419 or visit www.superiortray.com

DIMENSIONS

1 1/2"

A

Depth

1/2" Load Width

Top Rung

Unique dual width rungs provide 4 separate cable compartments without dividers. Dual width rung catalog numbers utilize our standard format, except both widths are shown.

TYPES OF CENTER HUNG TOP CENTER HUNG BOTTOM CENTER HUNG

DUAL CENTER HUNG WALL RACK

Depth A

Overall Height Top

A Overall Height

Bottom

Width

Load Width Top Bottom

3″ 5 ″ 3 ″ 6″ 6″ 7 ″ 4″ 6 ″ 4 ″ 9″ 9″ 10 ″ 6″ 8 ″ 6 ″ 12″ 12″ 13 ″ 18″ 18″ 24″ 24″

18″ 24″

CENTER HUNG TRAY

1/2"

A 1 1/2"

Load Width

Depth

Bottom Rung

Three 3/4″ wall spacers that are provided with each standard 10′ or 3m section must be mounted between back of spine and wall at mounting points. This unique design permits a wall rack to be installed without the use of a wall bracket.

page 29

Saving you Time, Saving you Money, Putting you First!

For more information, please call 604.572.4419 or visit www.superiortray.com

Width Bottom Rung Top Rung 6 ASP-TL-3 ASP-TT-3 9 ASP-TL-4 ASP-TT-4

12 ASP-TL-6 ASP-TT-6 18 ASP-TL-9 ASP-TT-9 24 ASP-TL-12 ASP-TT-12

Width Bottom Rung Top Rung 6 ASP-XL-3 ASP-XT-3 9 ASP-XL-4 ASP-XT-4

12 ASP-XL-6 ASP-XT-6 18 ASP-XL-9 ASP-XT-9 24 ASP-XL-12 ASP-XT-12

CENTER HUNG FITTINGS AND CONNECTORS HORIZONTAL TEE/90° CONNECTOR HORIZONTAL CROSS COUPLING

VERTICAL TEE/90° CONNECTOR (ASP-VT) SPLICE CONNECTOR (ASP-CR-B)

VERTICAL HINGE CONNECTOR (AFS-VCR) OFFSET VERTICAL CONNECTOR (ASP-VOFF-3)

HORIZONTAL HINGE CONNECTOR (AFS-HCR)

CENTER HUNG TRAY

Horizontal Tee/90°Connector Horizontal Cross Coupling

page 30

Saving you Time, Saving you Money, Putting you First!

For more information, please call 604.572.4419 or visit www.superiortray.com

Depth Part No. 3″ 4″ 6″

A3S-144-CR A4S-144-CR A6S-144-CR

Fixing Clamps and Screws included.

Catalog Number: ASP-WALL

Tray Width Part No.

6″ 9″

12″ 18″ 24″

WBK-6 WBK-7 WBK-9 WBK-12 WBK-15

Rung caps are used for system identification.

Color Catalog No. Red Black Blue Orange

RCAP – Red RCAP – Black RCAP – Blue RCAP – Orange

Attaches to rung with hardware provided.

ACCESSORIES BOX CONNECTOR BARRIER STRIP

WALL BRACKET WALL MOUNT

RUNG CAP

CABLE DROP OUT

Catalog Number: A B C ( ) – W – D

Rugged construction together with the ability to hang tray without any special clamps makes this bracket an efficient and economical device.

This connector allows for a sturdy connection for short wall-to-wall runs.

Drop Out Width Part No. Drop Out

Width Part No.

3″ 4 ″

6″ 8 ″

AVD-3-CR AVD-4 -CR AVD-6-CR AVD-8 -CR

9″

11 ″ 12″

AVD-9-CR AVD-11 -CR AVD-12-CR

Width

RUNG CAPOption A

Option B

Width (W): 3″, 6″, 9″, 12″, 18″, 24″ Depth (D): 3″, 4″, 6″

CENTER HUNG TRAY

For mounting to equipment and wall entrance flanges.

page 31

Saving you Time, Saving you Money, Putting you First!

For more information, please call 604.572.4419 or visit www.superiortray.com

CENTER HUNG COVERS Cover Attachment Illustration

Technical Data Width: 6″ to 24″ Length: 10 feet (120″) standard

Catalog Number For top mounted rung: CACTF-W-120 For bottom mounted rung: CACLF-W-120

Technical Data Width: 6″ to 24″ Length: 10 feet (120″) standard

Catalog Number For top mounted rung: AST-W-D-120 For bottom mounted rung: ASL-W-D-120

Note: Includes one sheet metal connector per insert. D – Depth W – Width.

RAIL END CAP BLIND END

Catalog Number: A E P ( ) - W - D Simplified one nut and bolt installation

to close up end of spline.

Catalog Number: A E P - C R

( ) For Cable Tray Please insert T for Top Rung and L for Bottom Rung. ( ) For Wall Rack Please insert TR for Top Right Hand, TL for Top Left Hand, LR for Lower Right Hand and LL for Lower Left Hand.

Simple one nut and bolt installation. Please advise width and rung type (top/bottom) when ordering.

CENTER HUNG TRAY

Cover

Insert

Notch permits cover to slide between the support nut and washers for secure attachment

Notch permits cover to slip under washer & nut for easy hold down

Center Hung Cover

SOLID TOP COVER SOLID BOTTOM INSERT