12770 Rue Brault, Mirabel QC, J7J 1P3 Sans Frais / Toll Free 1 888 657.2203 Tel. : 450 420.1839 Fax : 450 420.3882 [email protected]www.boulonsplus.net CERTIFICAT D'ASSEMBLAGE ASSEMBLY CERTIFICATE SVP PRENDRE NOTE QUE L'ASSEMBLAGE SUIVANT A ÉTÉ PRODUIT PAR BOULONS PLUS INC. ET NOMMÉ D'APRÈS LE NUMÉRO DE D'ASSEMBLAGE DU BOULON, DE L'ÉCROU AINSI QUE DE LA RONDELLE. PLEASE TAKE NOTE THAT THE FOLLOWING ASSEMBLY WAS DONE BY BOULONS PLUS INC. AND NAMED AFTER THE SET NUMBER MADE FROM THE BOLT, THE NUT AND THE WASHER. Sylvain Vaudry, Assurance-Qualité / Authorized test Clerk PLACAGE / GALVANISATION # PLATING / GALVANISATION # SET # BOULON / BOLT LOT # ÉCROU / NUT LOT # RONDELLE / WASHER LOT # L’ANALYSE CHIMIQUE PROVIENT DU FOURNISSEUR D’ACIER. ESSAIE DE CAPACITÉ ROTATIVE AVEC INDICATEUR DE TENSION. RÉSULTAT D’ESSAI = ACCEPTÉ. L’ASSEMBLÉE RENCONTRE LES EXIGENCES DE LA NORME ASTM A325. -- ÉCROUS LUBRIFIÉS. CHEMICAL ANALYSIS COMES FROM THE STEEL COMPANY. RC TEST DONE WITH TENSION MEASURING DEVICE. ROTATIONAL CAPACITY TEST = PASSED ASSEMBLY MEETS THE REQUIREMENTS OF THE ASTM A325 STANDARD. - NUTS LUBRICATED. 21111-270716 756162 1507-80458 D1605 3/4 X 8 1/2 A325-1 USA SET BLT+A563-C+F436-1 HDG CHARTER INFASC PRESTA
TEST REPORT Operations Center3281 West County Road 0 NSFrankfort, IN 46041-6966T. 765.654.0477F. 765.654.0857
Ship Date
Certification 530241*3*1
Report Date 07-21-16
Cust PO 436420
Lot Nbr 756162
Quantity 140
Mfg Date 10-01-15Boulons Plus12770 rue BraultMirabel, PQ J7J 1P3
Applicable Standards, Specifications, and Sampling Schemes:
For Non Structural Product:Test methods in accordance to ASTMF606/ISO 898-1 where applicable.Sampling plan in accordance toASTM F1470. Thread fit and dimensional properties are compliant to ASME B18.2.1. Mechanical properties are according to SAEJ429 or ISO 898-1 were applicable. Bolts passed a surface discontinuity inspection per ASTM F788. These bolts were manufacturedin the USA from domestic material and were not produced from heat in which Bismuth, Selenium, Tellurim, or Lead was intentionallyadded. Bolts were not exposed to Mercury or any other metal alloy that is liquid at ambient temperature during processing or while inour possession.The listed standards, specifications, and sampling schemes are of the revision in effect on the date of manufacture unless notedotherwise. Only those standards specifically noted under "test methods" or "additional test methods" are included on LE's scope oflaboratory accreditation.
Additional Information
None
This lot has been found to conform to the requirements of the above standards and specifications
We certify: The product furnished by Fontana Fasteners, Inc. was manufactured, sampled, tested, and inspected in accordance with the standards andspecifications listed above and with Fontana Fasteners, Inc. Quality Manual in effect as of the date of manufacture. The above data accurately represents valuesprovided by Fontana Fasteners, Inc. suppliers and/or values generated in one of Fontana Fasteners, Inc. A2LA accredited laboratories.This test report relates only to the sample tested above. This document may only be reproduced unaltered and may not be used for any purpose other than thepurpose of certifying the same or lesser quantity of the product specified herein. Reproduction, alteration or use of this document for any other purpose isprohibited, except as expressly provided in this certification. Fontana Fasteners, Inc. makes no (and disclaims all) representations, warranties and guaranteeswhatsoever, whether express, implied or statutory, including, without limitation, any warranty of merchantability or fitness for a particular purpose.
CERT #0122.02"MECHANICAL FIELD OF TESTING"
EMAIL
CHARTER STEEL TEST REPORTMelted in USA Manufactured in USA
Fontana Fasteners Inc3595 West State Road 28Frankfort,IN-46041
Cust P.O. 111401Customer Part # 955611468A1
Charter Sales Order 30098084Heat # 10390140
Ship Lot # 4356496Grade LEBA1 M SK FG RHQ 37/64
Process HRCCFinish Size 37/64
Ship date 30-JUL-15
I hereby certify that the material described herein has been manufactured in accordance with the specifications and standards listed below and that it satisfies these requirements. The recording of false, fictitious and fraudulent statements or entries on this document may be punishable as a felony under federal statute.
Charter Steel This MTR supersedes all previously dated MTRs for this orderSaukville, WI, USA
Janice BarnardManager of Quality Assurance
Rem: Load1,Fax0,Mail0 Printed Date : 07/30/2015Page 1 of 2
Test results of Heat Lot # 10390140Lab Code: 7388CHEM C MN P S SI NI CR MO CU SN V
Specifications: Manufactured per Charter Steel Quality Manual Rev Date 9/12/12Meets customer specifications with any applicable Charter Steel exceptions for the following customer documents:Customer Document = LE 1.1 Revision = 9 Dated = 27-NOV-07
Additional Comments: GRADE 30 Cr Mn B1
Page 2 of 2
The following statements are applicable to the material described on the front of this Test Report:1. Except as noted, the steel supplied for this order was melted, rolled, and processed in the United States meeting DFARS
compliance, LEEDS compliance, REACH compliance, ROHS-WEEE compliance, and Conflict Materials Restrictions.2. Mercury was not used during the manufacture of this product, nor was the steel contaminated with mercury during
processing.3. Unless directed by the customer, there are no welds in any of the coils produced for this order.4. The laboratory that generated the analytical or test results can be identified by the following key:
CertificateNumber
Lab Code Laboratory Address
0358-01 7388 CSSM Charter Steel Melting Division 1658 Cold Springs Road, Saukville, WI 53080
0358-02 8171 CSSR/CSSP
Charter Steel Rolling/ Processing Division 1658 Cold Springs Road, Saukville, WI 53080
0358-03 123633 CSFP Charter Steel Ohio Processing Division 6255 US Highway 23, Rising Sun, OH 43457
0358-04 125544 CSCM/CSCR
Charter Steel Cleveland 4300 E. 49th St., Cuyahoga Heights, OH 44125-1004
* * -- Subcontracted test performed by laboratory not in Charter Steel System
5. When run by a Charter Steel laboratory, the following tests were performed according to the latest revisions of the specifications listed below, as noted in the Charter Steel Laboratory Quality Manual:
Test Specifications CSSMCSSR/CSSP CSFP
CSCM/CSCR
Chemistry Analysis ASTM E415; ASTM E1019 X XMacroetch ASTM E381 X XHardenability (Jominy) ASTM A255; SAE J406; JIS G0561 X XGrain Size ASTM E112 X X X XTensile Test ASTM E8; ASTM A370 X X XRockwelll Hardness ASTM E18; ASTM A370 X X X XMicrostructure (spheroidization) ASTM A892 X XInclusion Content (Methods A, E) ASTM E45 X XDecarburization ASTM E1077 X X X
Charter Steel has been accredited to perform all of the above tests by the American Association for Laboratory Accreditation (A2LA). These accreditations expire 03/31/17. All other test results associated with a Charter Steel laboratory that appear on the front of this report, if any, were performed according to documented procedures developed by Charter Steel and are not accredited by A2LA.
6. The test results on the front of this report are the true values measured on the samples taken from the production lot. They do not apply to any other sample.
7. This test report cannot be reproduced or distributed except in full without the written permission of Charter Steel. The primarycustomer whose name and address appear on the front of this form may reproduce this test report subject to the following restrictions:
• It may be distributed only to their customers
• Both sides of all pages must be reproduced in full8. This certification is given subject to the terms and conditions of sale provided in Charter Steel's acknowledgement
(designated by our Sales Order number) to the customer's purchase order. Both order numbers appear on the front page of this Report.
9. Where the customer has provided a specification, the results on the front of this test report conform to that specification unless otherwise noted on this test report.
