(4) Equipment: OCX 8800 Oxygen/Combustibles Transmitters, Type OCX 88C
(5) Manufacturer: Emerson Process Management, Rosemount Analytical Inc.
(6) Address: 2400 Barranca Parkway, Irvine, CA 92606 USA
(7) This equipment and any acceptable variation thereto is specified in the schedule to this certificate and the documents therein referred to.
(8) DEKRA Certification B.V., notified body number 0344 in accordance with Article 9 of the Council Directive 94/9/EC of 23 March 1994, certifies that this equipment has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of equipment and protective systems intended for use in potentially explosive atmospheres given in Annex II to the directive.
The examination and test results are recorded in confidential test report number 216440600 issue 1.
(9) Compliance with the Essential Health and Safety Requirements has been assured by compliance with:
EN 60079-0 : 2012 EN 60079-1 : 2007
(10) If the sign ”X” is placed after the certificate number, it indicates that the equipment is subject to special conditions for safe use specified in the schedule to this certificate.
(11) This EC-Type Examination Certificate relates only to the design, examination and tests of the specified equipment according to the Directive 94/9/EC. Further requirements of the directive apply to the manufacturing process and supply of this equipment. These are not covered by this certificate.
(12) The marking of the equipment shall include the following:
II 2 G Ex d IIB + H2 T6 Gb (split architecture – electronics assembly)T3 Gb (split architecture – sensor assembly)T3 Gb (integral version)
This certificate is issued on 19 April 2016 and, as far as applicable, shall be revised before the date of cessation of presumption of conformity of (one of) the standards mentioned above as communicated in the Official Journal of the European Union.
(13) SCHEDULE
(14) to EC-Type Examination Certificate KEMA 04ATEX2308 Issue No. 3
Page 2/3
Form 100Version 5 (2013-07)
(15) Description
The Oxygen/Combustibles Transmitter Type OCX 88C is designed to continuously measure both oxygen and combustibles content of flue gases. The flameproof enclosure comprises two individual enclosures, one for the sensor assembly and one for the electronics assembly. These two enclosures may be configured either for integral architecture, separated by a sealed fitting, or for split architecture, separated by up to 150 feet interconnecting cabling.
Thermal data
Ambient temperature range: Sensors Housing -40 °C to +100 °CElectronics Housing -40 °C to +65 °CIntegral Assembly -40 °C to +65 °C
The sensor housing must not be mounted to any surface or flange that exceeds 195 °C.
The sample entering the sensor housing must not exceed 195 °C.
Electrical Data
Rated Line Voltage 100 to 240 Vac ± 10%, 50 to 60 HzRated Power Consumption 750 W maximum
Nomenclature
OCX 88C aa bb c d ee ff g h
I II III IV V VI VII VIII IX
Ref. Explanation Value Explanation
I Model OCX 88COxygen/Combustibles Transmitters– Explosion-Proof
II Probe Length and Material -Not included in the scope of the certificate.
III Probe Mounting Assembly - Not relevant for explosion safety
IV Mounting Hardware – Stack Side - Not relevant for explosion safety
V Mounting Hardware (probe side) - Not relevant for explosion safety
VIElectronics Housing - NEMA 4X, IP66 HART® Communications - Std.
- Not relevant for explosion safety
VII Electronic Mounting0102
Integral to Sensor Housing ElectronicsSplit Electronics and no cable
VIII In-Situ Filter - Not relevant for explosion safety
IX Accessories - Not relevant for explosion safety
Installation instructions
The instructions provided with the equipment shall be followed in detail to assure safe operation.
(13) SCHEDULE
(14) to EC-Type Examination Certificate KEMA 04ATEX2308 Issue No. 3
Page 3/3
Form 100Version 5 (2013-07)
(16) Test Report
No. 216440600 issue 1.
(17) Special conditions for safe use
None.
(18) Essential Health and Safety Requirements
Covered by the standards listed at (9).
(19) Test documentation
As listed in Test Report No. 216440600 issue 1.
KEMAi
oi EC-TYPE EXAMINATION CERTIFICATE (2) Equipment and protective systems intended for use in potentially explosive
(4) Equipment: Oxygen/ Combustibles Transmitter Model OCX 8800
(5) Manufacturer: Rosemount Analytical Inc., Process Analytic Division
(6) Address: 6565P Davis Industrial Parkway, Solon, Ohio 44139-3922, USA
(7) This equipment and any acceptable variation thereto is specified in the schedule to this certificate and the documents therein referred to.
(8) KEMA Quality B.V., notified body number 0344 in accordance with Article 9 ofthe Council Directive 94/9/EC of 23 March 1994, certifies that this equipment has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of equipment and protective systems intended for use in potentially explosive atmospheres given in Annex II to the directive.
The examination and test results are recorded in confidential test report number 212372300.
(9) Compliance with the Essential Health and Safety Requirements has been assured by compliance with:
EN 60079-0 : 2004 EN 60079-1 : 2004
(10) If the sign "X" is placed after the certificate number, it indicates that the equipment is subject to special conditions for safe use specified in the schedule to this certificate.
(11) This EC-Type Examination Certificate relates only to the design, examination and tests ofthe specified equipment according to the Directive 94/9/EC. Further requirements of the directive apply to the manufacturing process and supply of this equipment. These are not covered by this certificate.
(12) The marking ofthe equipment shall include the following:
II 2 G Ex d IIB + H2 T6 (split architecture - electronics assembly) T3 (split architecture - sensor assembly) T3 (integral version)
This certificate is issued on March 13, 2009 and, as far as applicable, shall be revised before the date of cessation of presumption of conformity of (one of) the standards mentioned above as communicated in the Official Journal of the European Union.
KEMA Quality B.V.
EH H.J.G.deWild mm Certification Manager Page 1/2 BvACOOl
@ Integral publication of this certificate and adjoining reports is allowed. This Certificate may only be reproduced in its entirety and without any change.
KEMA Quality B.V. Utrechtseweg 310, 6812 AR Arnhem P.O. Box 5185, 6802 ED Arnhem The Netherlands T +31 26 3 56 20 00 F +31 26 3 52 58 00 [email protected] www.kema.com Registered Arnhem 09085396
(14) to EC-Type Examination Certificate KEMA 04ATEX2308 Issue No. 2
(15) Description
The Oxygen/ Combustibles Transmitters Model OCX 8800 measures both the oxygen and combustibles content of flue gas. The flameproof enclosure is compromised two individual enclosures, one for the sensor assembly and one for the electronics assembly. These two enclosures may be configured either for integral separated with a sealed fitting or for split architecture separated by up to 150 feet with interconnect cabling between them.
Ambient temperature range: electronics housing -40 °C to +65 °C. sensor housing -40 °C to +100 °C. integral assembly -40 °C to +65 °C.
Process temperature range 0 °C to +1427 °C.
Electrical data
Rated voltage: 100 to 240 Vac Rated power: 750 W
Installation instructions
The cable entry devices and blanking elements of unused apertures shall be of a certified flameproof type, suitable for the conditions of use and correctly installed.
Routine tests
Each flange weldment assembly of the sensor enclosure probe shall be subjected to an overpressure test according to EN 60079-1, clause 15.1.3.1, using a test pressure of 14,5 bar for at least 10 seconds. The enclosure shall withstand the pressure without suffering permanent deformation of the joints or damage to the enclosure.
Routine tests are not required for the electronics housing since the type test has been made at a static pressure of four times the reference pressure.
