CERTIFICATE OF REGISTRATION This is to certify that the management system of: Tooling Systems Group (TSG) Main Site: 555 Plymouth Avenue NE, Grand Rapids, Michigan, 49505, USA See appendix for additional sites and additional site scopes has been registered by Intertek as conforming to the requirements of: ISO 9001:2015 The management system is applicable to: Develop and provide part manufacturing solutions Certificate Number: 0012567 Initial Certification Date: 16 October 2013 Date of Certification Decision: 11 September 2018 Issuing Date: 11 September 2018 Valid Until: 22 December 2020 Calin Moldovean President, Business Assurance Intertek Testing Services NA, Inc., 900 Chelmsford Street, Lowell, MA 01851. USA. In the issuance of this certificate, Intertek assumes no liability to any party other than to the Client, and then only in accordance with the agreed upon Certification Agreement. This certificate s validity is subject to the organization maintaining their system in accordance with Interteks requirements for systems certification. Validity may be confirmed via email at [email protected] or by scanning the code to the right with a smartphone. The certificate remains the property of Intertek, to whom it must be returned upon request. Page 1 of 4
Transcript
CERTIFICATEOF REGISTRATION
This is to certify that the management system of:
Tooling Systems Group (TSG)Main Site: 555 Plymouth Avenue NE, Grand Rapids, Michigan, 49505, USASee appendix for additional sites and additional site scopes
has been registered by Intertek as conforming to the requirements of:
ISO 9001:2015The management system is applicable to:
Develop and provide part manufacturing solutions
Certificate Number:0012567
Initial Certification Date:16 October 2013
Date of Certification Decision:11 September 2018
Issuing Date:11 September 2018
Valid Until:22 December 2020
Calin MoldoveanPresident, Business Assurance
Intertek Testing Services NA, Inc.,900 Chelmsford Street, Lowell, MA 01851.USA.
In the issuance of this certificate, Intertek assumes no liability to any party other than to the Client, and then only in accordance with the agreed upon Certification Agreement. This certificate’s validity is subject to the organization maintaining their system in accordance with Intertek’s requirements for systems certification. Validity may be confirmed via email at [email protected] or by scanning the code to the right with a smartphone. The certificate remains the property of Intertek, to whom it must be returned upon request.
Page 1 of 4
APPENDIX TOCERTIFICATE OFREGISTRATION
This appendix identifies the locations covered by the management system of:
Tooling Systems Group (TSG)This appendix is linked to the Main Certificate # 0012567 and cannot be shown nor reproduced without it.
Ultimate Gaging Systems (UGS)
555 Plymouth Avenue NE, Grand Rapids, Michigan, USA
Design, machine, assemble, build and certify check fixture and inspection gages.
Hot Stamp Tooling Systems (HTS)
555 Plymouth Avenue NE, Grand Rapids, Michigan, USA
Design and manufacture of metal stamping dies for the automotive, appliance, furniture and other industries.
Advanced Tooling Systems (ATS)
1166 - 7 Mile, Comstock Park, Michigan, 49321, USA
Design and manufacture of metal stamping dies for the automotive, appliance, furniture and other industries.
In the issuance of this certificate, Intertek assumes no liability to any party other than to the Client, and then only in accordance with the agreed upon Certification Agreement. This certificate’s validity is subject to the organization maintaining their system in accordance with Intertek’s requirements for systems certification. Validity may be confirmed via email at [email protected] or by scanning the code to the right with a smartphone. The certificate remains the property of Intertek, to whom it must be returned upon request.
Page 2 of 4
APPENDIX TOCERTIFICATE OFREGISTRATION
This appendix identifies the locations covered by the management system of:
Tooling Systems Group (TSG)This appendix is linked to the Main Certificate # 0012567 and cannot be shown nor reproduced without it.
Engineered Tooling Systems (ETS)
2780 Courier NW, Grand Rapids, Michigan, USA
Design and manufacture of metal stamping dies for the automotive, appliance, furniture and other industries.
Steel Craft Technologies
8057 Graphic Industrial Park NE, Belmont, Michigan, USA
1155 42nd Street SE, Grand Rapids, Michigan, 49508, USA
Site 1: Fabrication, machining and assembly of steel plate products for machine building, stamping dies and injection molding servicing the aviation, space, defense, automotive, food, furniture, agricultural, urban development, mining and oil industries.
Site 2: Machining and assembly of steel plate products for machine building, stamping dies and injection molding serving the aviation, space, defense, automotive, food, furniture, agricultural, urban development, mining and oil industries.
In the issuance of this certificate, Intertek assumes no liability to any party other than to the Client, and then only in accordance with the agreed upon Certification Agreement. This certificate’s validity is subject to the organization maintaining their system in accordance with Intertek’s requirements for systems certification. Validity may be confirmed via email at [email protected] or by scanning the code to the right with a smartphone. The certificate remains the property of Intertek, to whom it must be returned upon request.
Page 3 of 4
APPENDIX TOCERTIFICATE OFREGISTRATION
This appendix identifies the locations covered by the management system of:
Tooling Systems Group (TSG)This appendix is linked to the Main Certificate # 0012567 and cannot be shown nor reproduced without it.
Dienamic Tooling Systems (DTS)
303 Sam Rayburn Parkway, Lenoir City, Tennessee, USA
Design and manufacture of metal stamping dies for the automotive, appliance, furniture and other industries.
Specialty Tooling Systems (STS)
4513 Three Mile Road, Walker, Michigan, 49534, USA
Design, build, and assembly of automation equipment.
Rapid Tooling Systems (RTS)
555 Plymouth Avenue NE, Grand Rapids, Michigan, 49503, USA
Design and manufacture of metal stamping dies for the automotive, appliance, furniture and other industries.
In the issuance of this certificate, Intertek assumes no liability to any party other than to the Client, and then only in accordance with the agreed upon Certification Agreement. This certificate’s validity is subject to the organization maintaining their system in accordance with Intertek’s requirements for systems certification. Validity may be confirmed via email at [email protected] or by scanning the code to the right with a smartphone. The certificate remains the property of Intertek, to whom it must be returned upon request.
