CFW 09 - Pamensky 09 - Table of Products Notes: The maximum motor power ratings listed above are...

MotorsAutomation

MachinesTransformers

PAMENSKY

Variable Frequency DriveCFW 09Three Phase 200-240V - 1.5 - 75 HP

Three Phase 380-480V - 1.5 - 500 HP

Three Phase 500-600/690V - 2 - 500 HP

2 | CFW 09 - Variable Frequency Drive

CFW 09 - Variable Frequency DriveThe CFW 09‘s Vectrue Technology combines V/F, Sensorless Vector and Closed Loop Vector (with encoder) control techniques in one product. Optimal Braking saves the need for the dynamic braking resistor in some applications allowing a more compact and economical solution.

Standard Features

• V/Hz or Sensorless Vector Control via parameter selection

• Self Tuning to motor parameters• NEMA 1 Enclosure up to 200HP• IP20 Enclosure from 250 to 500HP• 200-240V, 380-480V or 500-600/690V input

voltage• Single or Three-phase input voltage up to

3HP/230V *Call 1 877 PAMENSKY for higher than 3HP

• 150% current overload capacity• DC bus connections accessible• Detachable Smart Keypad with dual display

and Copy Function• 32 bit RISC microprocessor controlled PWM

output• 1.25 / 2.5 / 5 / 10 kHz adjustable switching

frequency• Six isolated programmable digital inputs• Three programmable relay outputs (250Vac /

1A)• Two isolated programmable analog inputs• Two programmable analog outputs (0 - 10

Vdc)• Protective features: Over current, motor

overload, drive over temperature, output phase-to-phase and phase-to-ground short circuit, DC bus over and under voltage, power supply under voltage and phase loss and external fault

Standard Features - cont.

• Control features: Linear and “S” ramp acceleration and deceleration, local/remote control, DC braking, torque boost, motor slip compensation, electronic pot, preset speeds, adjustable V/Hz profi le, maximum and minimum adjustable motor speed limits, three skip frequencies, adjustable output current limit, JOG, ride-thru, fl ying start and PID regulator

• Display readings: Motor speed, frequency, voltage, current and torque, output power (kW), last ten faults, drive status, digital and analog I/O status, hours powered and hours running

• Ambient: 32ºF (0ºC) to 104ºF (40ºC), 3300 ft (1000m) altitude, 90% humidity, non- condensing

Optional Features

• Closed loop vector control• Remote keypad with cable and mounting

frame• RS-232 or RS-485 Serial Interface• On/Off line PC programming with Superdrive• Fieldbus Comm: Profi bus DP, DeviceNet or

Modbus RTU (Requires optional RS-232 or RS-485 Interface), Ethernet TCP/IP

• Encoder buffered output• Additional digital and analog I/O• Dynamic Braking capabilities for most models

CFW 09 - Variable Frequency Drive | 3

CFW 09 - Table of Products

380-480VElectrical Data Mechanical Data Purchasing Data

Current(A)

Built-In DynamicBraking

Maximum Applicable Motor

FrameWeight

(lb)Degree of Protection

Dimensions(in)

H x W x DWEG Part Number

List Price

Constant Torque Variable Torque

CT VT HP KW HP KW

3.6 Yes 1.5 1 1.5 1.1 1 8 NEMA 1 8.27 x 5.63 x 7.72 CFW090003T3848ESZ $1,6464 Yes 2 2 2 1.5 1 8 NEMA 1 8.27 x 5.63 x 7.72 CFW090004T3848ESZ 1,685

5.5 Yes 3 2 3 2.2 1 8 NEMA 1 8.27 x 5.63 x 7.72 CFW090005T3848ESZ 1,7449 Yes 5.5 4 5.5 4 1 8 NEMA 1 8.27 x 5.63 x 7.72 CFW090009T3848ESZ 1,884

13 Yes 7.5 6 7.5 5.5 2 13 NEMA 1 11.42 x 7.16 x 7.72 CFW090013T3848ESZ 1,98016 Yes 10 8 10 7.5 2 13 NEMA 1 11.42 x 7.16 x 7.72 CFW090016T3848ESZ 2,46424 Yes 15 11 15 11 2 13 NEMA 1 11.42 x 7.16 x 7.72 CFW090024T3848ESZ 2,654

30 36 Yes 20 15 25 18.5 3 42 NEMA 1 15.35 x 8.78 x 10.79 CFW090030T3848ESZ 3,78038 45 Optional 25 19 30 22 4 50 NEMA 1 18.70 x 9.84 x 10.79 CFW090038T3848ESZ 4,50245 54 Optional 30 22 30 22 4 50 NEMA 1 18.70 x 9.84 x 10.79 CFW090045T3848ESZ 5,62860 70 Optional 40 30 50 37 5 90 NEMA 1 21.65 x 13.19 x 10.79 CFW090060T3848ESZ 6,97670 86 Optional 50 37 60 45 5 90 NEMA 1 21.65 x 13.19 x 10.79 CFW090070T3848ESZ 7,43086 105 Optional 60 45 75 55 6 121 NEMA 1 26.57 x 13.19 x 11.77 CFW090086T3848ESZ 9,110

105 130 Optional 75 55 100 55 6 121 NEMA 1 26.57 x 13.19 x 11.77 CFW090105T3848ESZ 9,956142 174 Optional 100 75 125 90 7 154 NEMA 1 32.87 x 13.19 x 12.20 CFW090142T3848ESZ 11,862

180 External DB 150 110 150 110 8 221 NEMA 1 38.38 x 16.14 x 14.57 CFW090180T3848ESZ 18,778211 External DB 150 110 150 110 8 221 NEMA 1 38.38 x 16.14 x 14.57 CFW090211T3848ESZ 21,410240 External DB 200 150 200 150 8 221 NEMA 1 38.38 x 16.14 x 14.57 CFW090240T3848ESZ 22,280312 External DB 250 185 250 185 9 476 IP20 39.37 x 27.56 x 19.33 CFW090312T3848ESZ 26,396361 External DB 300 220 300 220 9 476 IP20 39.37 x 27.56 x 19.33 CFW090361T3848ESZ 27,584450 External DB 350 260 350 260 10 571 IP20 46.65 x 27.56 x 19.33 CFW090450T3848ESZ 35,964515 External DB 400 300 400 300 10 571 IP20 46.65 x 27.56 x 19.33 CFW090515T3848ESZ 41,636600 External DB 500 370 500 370 10 571 IP20 46.65 x 27.56 x 19.33 CFW090600T3848ESZ 47,492


Current(A)



FrameWeight


Dimensions(in)


List Price


CT VT HP KW HP KW

6 Yes 1.5 1.1 1.5 1.1 1 8 NEMA 1 8.27 x 5.63 x 7.72 CFW090006T2223ESZ $1,468 7 Yes 2 1.5 2 1.5 1 8 NEMA 1 8.27 x 5.63 x 7.72 CFW090007T2223ESZ 1,486

10 Yes 3 2.2 3 2.2 1 8 NEMA 1 8.27 x 5.63 x 7.72 CFW090010T2223ESZ 1,56313 Yes 3 2.2 3 2.2 1 8 NEMA 1 8.27 x 5.63 x 7.72 CFW090013T2223ESZ 1,60516 Yes 5 3.7 5 3.7 2 13 NEMA 1 11.42 x 7.16 x 7.72 CFW090016T2223ESZ 1,73124 Yes 7.5 5.5 5.5 5.5 2 13 NEMA 1 11.42 x 7.16 x 7.72 CFW090024T2223ESZ 2,27428 Yes 10 7.5 10 7.5 2 13 NEMA 1 11.42 x 7.16 x 7.72 CFW090028T2223ESZ 2,51745 Yes 15 11 15 11 3 42 NEMA 1 15.35 x 8.78 x 10.79 CFW090045T2223ESZ 3,837

54 68 Optional 20 15 25 18.5 4 50 NEMA 1 18.70 x 9.84 x 10.79 CFW090054T2223ESZ 5,33970 86 Optional 25 18.5 30 22 5 90 NEMA 1 21.65 x 13.19 x 10.79 CFW090070T2223ESZ 7,71686 105 Optional 30 22 40 30 5 90 NEMA 1 21.65 x 13.19 x 10.79 CFW090086T2223ESZ 8,124

105 130 Optional 40 30 50 37 6 121 NEMA 1 26.57 x 13.19 x 11.77 CFW090105T2223ESZ 9,788130 150 Optional 50 37 60 45 6 121 NEMA 1 26.57 x 13.19 x 11.77 CFW090130T2223ESZ 10,488142 174 Optional 50 37 60 45 7 154 NEMA 1 32.87 x 13.19 x 12.20 CFW090142T2223ESZ 12,178

180 External DB 60 45 60 45 8 221 NEMA 1 38.38 x 16.14 x 14.57 CFW090180T2223ESZ 16,863240 External DB 75 55 75 55 8 221 NEMA 1 38.38 x 16.14 x 14.57 CFW090240T2223ESZ 24,057

Notes: The maximum motor power ratings listed above are based on WEG 2 and 4 pole motors. For motors with different numbers of poles (ie. 6 and 8 poles), other voltages and/ or from other manufacturers, specify the VFD through the motor rated current.

220-230V - With Optional Dynamic BrakingElectrical Data Mechanical Data Purchasing Data

Current(A)



FrameWeight


Dimensions(in)


List Price


CT VT HP KW HP KW

54 68 Yes 20 15 25 18.5 4 50 NEMA 1 18.70 x 9.84 x 10.79 CFW090054T2223EODBZ $6,37770 86 Yes 25 18.5 30 22 5 90 NEMA 1 21.65 x 13.19 x 10.79 CFW090070T2223EODBZ 9,10986 105 Yes 30 22 40 30 5 90 NEMA 1 21.65 x 13.19 x 10.79 CFW090086T2223EODBZ 9,589

105 130 Yes 40 30 50 37 6 121 NEMA 1 26.57 x 13.19 x 11.77 CFW090105T2223EODBZ 11,447130 150 Yes 50 37 60 45 6 121 NEMA 1 26.57 x 13.19 x 11.77 CFW090130T2223EODBZ 12,266142 174 Yes 50 37 60 45 7 154 NEMA 1 32.87 x 13.19 x 12.20 CFW090142T2223EODBZ 15,132


CFW 09 - Table of Products



Current(A)



FrameWeight


Dimensions(in)


List Price


CT VT HP KW HP KW

38 45 Yes 25 19 30 22 4 50 NEMA 1 18.70 x 9.84 x 10.79 CFW090038T3848EODBZ $5,79045 54 Yes 30 22 30 22 4 50 NEMA 1 18.70 x 9.84 x 10.79 CFW090045T3848EODBZ 7,88460 70 Yes 40 30 50 37 5 90 NEMA 1 21.65 x 13.19 x 10.79 CFW090060T3848EODBZ 9,98470 86 Yes 50 37 60 45 5 90 NEMA 1 21.65 x 13.19 x 10.79 CFW090070T3848EODBZ 10,83286 105 Yes 60 45 75 55 6 121 NEMA 1 26.57 x 13.19 x 11.77 CFW090086T3848EODBZ 13,457

105 130 Yes 75 55 100 55 6 121 NEMA 1 26.57 x 13.19 x 11.77 CFW090105T3848EODBZ 15,678142 174 Yes 100 75 125 90 7 154 NEMA 1 32.87 x 13.19 x 12.20 CFW090142T3848EODBZ 18,515


Current(A)



FrameWeight


Dimensions(in)


List Price


CT VT HP KW HP KW

22 27 Yes 20 15 25 18.5 4 50 NEMA 1 18.7 x 9.8 x 10.8 CFW090022T5060EODBZ $5,52627 32 Yes 25 18.5 30 22 4 50 NEMA 1 18.7 x 9.8 x 10.8 CFW090027T5060EODBZ 6,51632 32 Yes 30 22 30 22 4 50 NEMA 1 18.7 x 9.8 x 10.8 CFW090032T5060EODBZ 8,83344 53 Yes 40 30 50 37 7 154 NEMA 1 32.9 x 13.2 x 11.8 CFW090044T5060EODBZ 11,49053 63 Yes 50 37 60 45 7 154 NEMA 1 32.9 x 13.2 x 11.8 CFW090053T5060EODBZ 13,45463 79 Yes 60 45 75 55 7 154 NEMA 1 32.9 x 13.2 x 11.8 CFW090063T5060EODBZ 16,12079 99 Yes 75 55 100 75 7 154 NEMA 1 32.9 x 13.2 x 11.8 CFW090079T5060EODBZ 18,968


Current(A)



FrameWeight


Dimensions(in)


List Price


CT VT HP KW HP KW

2.9 4.2 Yes 2 1.5 2 2.2 2 13 NEMA 1 11.4 x 7.2 x 7.7 CFW090002T5060ESZ $1,7424.2 7 Yes 3 2.2 5 4 2 13 NEMA 1 11.4 x 7.2 x 7.7 CFW090004T5060ESZ 1,8017 10 Yes 5 3.7 7.5 5.5 2 13 NEMA 1 11.4 x 7.2 x 7.7 CFW090007T5060ESZ 2,305

10 12 Yes 7.5 5.5 10 7.5 2 13 NEMA 1 11.4 x 7.2 x 7.7 CFW090010T5060ESZ 2,41312 14 Yes 10 7.5 15 9.2 2 13 NEMA 1 11.4 x 7.2 x 7.7 CFW090012T5060ESZ 2,93514 14 Yes 15 9.2 15 9.2 2 13 NEMA 1 11.4 x 7.2 x 7.7 CFW090014T5060ESZ 3,27122 27 Optional 20 15 25 18.5 4 50 NEMA 1 18.7 x 9.8 x 10.8 CFW090022T5060ESZ 4,19427 32 Optional 25 18.5 30 22 4 50 NEMA 1 18.7 x 9.8 x 10.8 CFW090027T5060ESZ 4,92832 32 Optional 30 22 30 22 4 50 NEMA 1 18.7 x 9.8 x 10.8 CFW090032T5060ESZ 6,70844 53 Optional 40 30 50 37 7 154 NEMA 1 32.9 x 13.2 x 11.8 CFW090044T5060ESZ 8,94153 63 Optional 50 37 60 45 7 154 NEMA 1 32.9 x 13.2 x 11.8 CFW090053T5060ESZ 10,55063 79 Optional 60 45 75 55 7 154 NEMA 1 32.9 x 13.2 x 11.8 CFW090063T5060ESZ 12,55879 99 Optional 75 55 100 75 7 154 NEMA 1 32.9 x 13.2 x 11.8 CFW090079T5060ESZ 14,928

107 147 External DB 100 75 150 110 8E 253 NEMA 1 45.1 x 16.1 x 14.6 CFW090107T5069ESZ 18,119147 196 External DB 150 110 200 150 8E 253 NEMA 1 45.1 x 16.1 x 14.6 CFW090147T5069ESZ 27,295211 211 External DB 200 150 200 150 8E 253 NEMA 1 45.1 x 16.1 x 14.6 CFW090211T5069ESZ 36,995247 315 External DB 250 185 300 220 10E 682 IP20 46.6 x 27.5 x 22.9 CFW090247T5069ESZ 39,018315 343 External DB 300 220 350 250 10E 682 IP20 46.6 x 27.5 x 22.9 CFW090315T5069ESZ 42,264343 318 External DB 350 250 400 300 10E 682 IP20 46.6 x 27.5 x 22.9 CFW090343T5069ESZ 56,796418 472 External DB 400 300 500 370 10E 682 IP20 46.6 x 27.5 x 22.9 CFW090418T5069ESZ 61,225472 555 External DB 500 370 600 450(370) 10E 682 IP20 46.6 x 27.5 x 22.9 CFW090472T5069ESZ 65,161


CFW 09 Shark - Variable Frequency DriveCFW 09 Drives with a NEMA 4X (IP 56) enclosure, designed for highly aggressive environments including:• Chemical industry• Petrochemical• Food industry• Other applications requiring full protection

Standard Features

• V/Hz or Sensorless Vector Control via parameter selection

• Self Tuning to motor parameters• NEMA 4X (IP56) Stainless Steel Enclosure• 200-240V up to 5HP, 380-480V up to 10HP• Single or Three-phase input voltage up to

3HP/230V *Call 1 877 PAMENSKY for higher than 3HP

• 150% current overload capacity• DC bus connections accessible• Detachable Smart Keypad with dual display

and Copy Function• 32 bit RISC microprocessor controlled PWM

output• 1.25 / 2.5 / 5 / 10 kHz adjustable switching

frequency• Six isolated programmable digital inputs• Three programmable relay outputs (250Vac /

1A)• Two isolated programmable analog inputs• Two programmable analog outputs (0 - 10

Vdc)• Protective features: Over current, motor

overload, drive over temperature, output phase-to-phase and phase-to-ground short circuit, DC bus over and under voltage, power supply under voltage and phase loss and external fault

Standard Features - cont.

• Control features: Linear and “S” amp acceleration and deceleration, local/remote control, DC braking, torque boost, motor slip compensation, electronic pot, preset speeds, adjustable V/Hz profi le, maximum and minimum adjustable motor speed limits, three skip frequencies, adjustable output current limit, JOG, ride-thru, fl ying start and PID regulator

• Display readings: Motor speed, frequency, voltage, current and torque, output power (kW), last four faults, drive status, digital and analog I/O status, hours powered and hours running

• Ambient: 32ºF (0ºC) to 104ºF (40ºC), 3300 ft (1000m) altitude, 90% humidity, non- condensing

Optional Features

• Closed loop vector control• RS-485 Serial Interface• On/Off line PC programming with Superdrive• Fieldbus Comm: Profi bus DP, DeviceNet or

Modbus RTU (Requires optional RS-232 or RS-485 Interface), Ethernet TCP/IP

• Encoder buffered output• Additional digital and analog I/O• Dynamic Braking capabilities for all models


CFW 09 Shark - Table of Products


220-230V

Electrical Data Mechanical Data Purchasing Data

Current(A)



FrameWeight


Dimensions(in)


List Price


CT VT HP KW HP KW

6 Yes 1.5 1.1 1.5 1.1 1 10 NEMA 4X 14.2 x 9.2 x 8.5 CFW090006T2223PON4Z $2,660

7 Yes 2 1.5 2 1.5 1 10 NEMA 4X 14.2 x 9.2 x 8.5 CFW090007T2223PON4Z 2,782



380-480V

Electrical Data Mechanical Data Purchasing Data

Current(A)



FrameWeight


Dimensions(in)


List Price


CT VT HP KW HP KW

3.6 Yes 2 1.5 2 1.5 1 10 NEMA 4X 14.2 x 9.2 x 8.5 CFW090003T3848PON4Z $2,782


5.5 Yes 3 2.2 3 2.2 1 10 NEMA 4X 14.2 x 9.2 x 8.5 CFW090005T3848PON4Z 2,980


13 Yes 7.5 5.5 7.5 5.5 2 15 NEMA 4X 16.2 x 10.2 x 8.5 CFW090013T3848PON4Z 3,300



CFW 09 - Accessories

* Modbus RTU –requires optional RS-232 or RS-485 interface.

Dynamic Braking

Description Part Number List Price

External Dynamic Braking Module for 180A Model (16 X 9 X 10 NEMA 1 Enclosure) DBW01.0165D21801SZ $2,154

External Dynamic Braking Module for 211 & 240A Models (16 X 9 X 10 NEMA 1 Enclosure) DBW01.0240D21801SZ 2,630

External Dynamic Braking Module for 312, 361,450,515, & 600A Models (16 X 9 X 10 NEMA 1 Enclosure) DBW01.0300D21801SZ 3,208

External Dynamic Braking Module for 107,147,211,& 247A Models at 575V (16 X 9 X 10 NEMA 1 Enclosure) DBW02.0210D50691SZ 3,954

External Dynamic Braking Module for 315 & 343A Models at 575V (16 X 9 X 10 NEMA 1 Enclosure) DBW02.0300D50691SZ 5,214

External Dynamic Braking Module for 418 & 472 Amp Models at 575V (16 X 9 X 10 NEMA 1 Enclosure) DBW02.0380D50691SZ 6,462

Keypads


Standard Keypad with LED & LCD HMICFW09LCD $210

NEMA 4/IP56 Remote Keypad with LED & LCD HMI CFW09 LCD N4 274

Remote Keypad FRAME KIT KMR CFW09 90

Blank Keypad with Power & Error LED’s TCL CFW09 30

Caps


External DC Bus Cap Kit 1500uF (includes bleeder resistor, mounting bracket, & screws) CFW09CAP1500 $240

External DC Bus Cap Kit 4700uF (includes bleeder resistor, mounting bracket, & screws) CFW09CAP4700 280

Keypad Cables


1m (3.3 ft) Remote Keypad Cable CAB HMI 09 1 $32

2m (6.6 ft) Remote Keypad Cable CAB HMI 09 2 40

3m (10 ft) Remote Keypad Cable CAB HMI 09 3 50

5m (16 ft) Remote Keypad Cable CAB HMI 09 5 76

7.5m (25 ft) Remote Keypad Cable (Requires CFW09KMR09) CAB HMI 09 7 90

10m (33 ft) Remote Keypad Cable (Requires CFW09KMR09) CAB HMI 09 10 108

Communication


Superdrive PC Communication Kit (includes software & hardware accessories) KSD CFW09 $180

RS-232 Serial Interface KCS CFW09 88

Profi bus DP Communication Kit KFB DP 1,060

DeviceNet Communication Kit KFB DN 912

Ethernet IP Communication Kit (V3.70 or higher) KFB EN 1,590


CFW 09 - AccessoriesI/O Expansion Boards


I/O Exp. Board A with Encoder Input, Encoder Output, RS-485 Serial Interface, I4 bit A/D, I4 bit D/A’s, Digital Inputs and Outputs + Thermistor (PTC) Input

EBA.01 CFW09 $1,436

I/O Exp. Board A with RS-485 Serial Interface, Digital Inputs and Outputs + Thermistor (PTC) Input EBA.02 CFW09 340

I/O Exp. Board A with I4 bit A/D, I4 bit D/A’s, Digital Inputs and Outputs + Thermistor (PTC) Input EBA.03 CFW09 664I/O Exp. Board B with Encoder Input, Encoder Output, RS-485 Serial Interface, Isolated Analog Input, Isolated Analog Outputs, Digital Inputs and Outputs + Thermistor (PTC) Input

EBB.01 CFW09 1,210

I/O Exp. Board B with Encoder Input with internal Power Supply - 12VDC, Digital Inputs and Outputs + Thermistor (PTC) Input

EBB.02 CFW09 570

I/O Exp. Board B with Isolated Analog Input, Isolated Analog Outputs, Digital Inputs and Outputs + Thermistor (PTC) Input

EBB.03 CFW09 678

I/O Exp. Board B with Encoder Input, 5V Power Supply for Encoder, Buffered Outputs for Encoder Signals, RS-485 Serial Port, 24V Digital Input, 2 X 24V OC Digital Outputs, 0…10V/4-20mA Analog Input, 2 X 4-20mA Analog Outputs and PTC Thermistor Input

EBB.04 CFW09 1,510

I/O Exp. Board B with 2 X 4-20mA Analog Outputs EBB.05 CFW09 440

I/O Exp. Board C with Encoder Input, 5-15VDC External Power Supply EBC1.01 CFW09 198

I/O Exp. Board C with Encoder Input with internal Power Supply - 12VDC EBC1.03 CFW09 530

I/O Exp. Board E with RS-485 Serial Interface, Digital or Thermistor (PTC) Input EBE.01 CFW09 196

PLC/Motion Control Board PLC1.01 972

PLC/Motion Control Board with Communication Capabilities PLC2.00 1,166

Through Surface Mounting


Kit for Through Surface Mounting - Size 3 KMF - CFW09 - M3 $16

Kit for Through Surface Mounting - Size 4 KMF - CFW09 - M4 20






Why the CFW 09?

For applications requiring short stopping times and/or stops under high inertial loading, the traditional braking devices call for Dynamic Braking, in which the load kinetic energy is regenerated to the inverter DC link and the excess of which is dissipated in the form of heat in a braking resistor which is interlinked to the power circuit. The CFW 09 VSD has a built-in “Optimal Braking ®” function, for the vector mode, enabling an optimal braking which can cater for many applications that could previously only be solved by dynamic braking. This technological innovation enables high dynamic performance activation/starts to be obtained with braking torques about 5 times the DC braking torque besides the great advantage of eliminating the need for a braking resistor.The graph shows the advantage of this new braking system “ Optimal Braking ®“, thereby ensuring an ideal solution for braking applications at low cost.

• High performance RISC 32 bit microprocessor

• Vector and Scaler Control with selection by parameter

• Detachable SMART keypad with dual display (LCD and LED)

• Wide power range: 1.1.. 1,100 kW• Variable and Constant Torque ratings• Degree of Protection NEMA 1 / IP 20

standard up to 200HP, IP20 from 250HP and NEMA 4X / IP56 in stainless steel enclosure up to 10HP

• Compact design• Simplifi ed installation and programming• Oriented start-up• Through surface mounting option• On/Off-line PC programming with

SuperDrive software (Optional)• DC bus connections available• Fieldbus network communication:

Profi bus DP, DeviceNet, or Ethernet TCP/IP (optional). Modbus RTU (built-in) also available

• International certifi cations including UL and cUL, CE, C-Tick and IRAM

CFW 09 - Optimal BrakingTM CFW 09 - Other Advantages


CFW 09 - Features

Optional RS-232 Interface Module for PC Communication

NEMA 1 / IP20 Enclosure

Flange for Through Surface Mounting

Optional I/O Expansion Boards for:• RS-485 Serial

Interface• Additional Inputs/

Outputs• Encoder

Feedback

2 Programmable Analog Outputs

Dynamic Braking Resistor Connection

DC Bus Connection for:• DC Bus Choke• Common DC BusC• Regenerative Rectifi er

Motor Connection Output

AC Supply Input

Metallic Conduit Connection System

2 Programmable Analog Inputs

6 Programmable Isolated Digital Inputs

Fieldbus Communication Network Modules for:• Profi bus DP (optional)• DeviceNet (optional)• DeviceNet Drive Profi le

(optional)• Modbus RTU (built-in)

2 Lines with 16 Characters LCD Display

7 Segment LED Display

Detachable Keypad with Multi-language Double Display (LCD + LED) and Copy Function

3 Programmable Relay Outputs

High Performance 32 bit RISC Microprocessor

Standard SMD Control Board for all Models


CFW 09 - KeypadIntelligent KeypadIntelligent operating interface with double display, LED (7 segment) and LCD (2 lines with 16 characters), providing optimum distant viewing along with a detailed description of all parameters and messages.

Selectable LanguageThe intelligent operating interface also allows the product user to choose the language to be used in programming, reading and presenting the parameters and alphanumerical messages through the LCD display.The product’s high hardware and software capacity enables the user to use various languages such as Portuguese, English and Spanish so as to make it adaptable for users throughout the world.

Oriented Start-up The CFW 09 “Oriented Start-Up” feature was specially created to facilited and expedite the start-up procedure. At the fi rst power-up or after a reset to factory default parameters, and automatic programming routine guides the operator through a sequence of steps for the introduction of the minimum parameters necessary for a perfect adaptation between drive and motor.

COPY Function This intelligent keypad also incorporates a “Copy Function”, which allows copying parameters from one drive to others, providing easy and reliable programming repeatability for duplicate applications.Note: Call 1 877 PAMENSKY for compatibility

LED Display

LCD Display

“LOCAL” LED

“REMOTE” LED

“FORWARD“ LED

“REVERSE” LED

VSD “A” VSD “B”

CFW 09 Keypad Keypad CFW 09


CFW 09 - Keypad Functions

Superdrive Programming Software

Windows Programming software via PC microcomputer, for parameterization, control and monitoring of CFW 09 drives.It allows editing of “on-line” parameters, directly on the drive or editing “off-line” parameter fi les, saved in the microcomputer.

It also allows storage of parameter fi les of all CFW 09 drives available on the installation.The software also incorporates functions to transfer the set of parameters from the microcomputer to the drive, as well as from the drive to the microcomputer.

The communication between drive and microcomputer is made via serial interface RS-232 (point to point) or RS-485 for network interconnection.

Stops the drive via a controlled deceleration ramp. Resets the inverter after a fault trip has occurred.

Increases the speed or parameter number/content.

Decreases the speed or parameter number/content.

Switches the display between the parameter number and its content (position/content) for programming.

While pressed the motor is run at JOG speed.

FWD/REV key. When pressed reverses the direction of rotation.

Selects the drive operating mode as Local or Remote.

Starts the drive via a controlled acceleration ramp. When running switches the display indication: rpm - Volts - Status - Torque - Hz - Amps


The CFW 09 allows fl exible mounting confi gurations. Besides the traditional Base mounting, they allow fl ange mounting, where the heat sink is mounted at the back of the mounting plate.

As a result, the warm air generated by the power components inside the panel is so blown out that minimizes drive overheating, which is caused by heating sources inside the panel.

Base mounting Flange mounting

Outlet air fl ow

Outlet air fl ow

Inlet air fl ow

Inlet air fl ow

CFW 09 - Mounting Confi gurations

This function replaces the traditional linear acceleration and deceleration ramps by Type “S” Ramps providing smoother starting, braking and approximation to the set speed curves. The practical result is the elimination of mechanical shocks, which are undesirable and some times unpractical for certain applications.

Overlapping PID Regulator

Up to eight different speeds can be programmed by the user and selected via the combination of three digital Inputs. These Inputs can be switched by any external device such as Limit Switches, Photocells, Proximity Sensors, PLC, etc.

“S” Ramp

Multi-speed

This built-in digital PID regulator was designed for applications where a process variable (fl ow, pressure, level, etc.) has to be controlled by the motor speed. To implement this regulator the CFW 09 needs a set point and a feedback signal from the process variable sensor so that a closed loop is formed. This function eliminates the need for an external regulator to control the process reducing the solution cost.

CFW 09 - Special Functions

Velocidade (rpm)

Outfl ow referenceor pressure reference

DI 4 5 6

n1

0 0 0

n2

0 0 1

n3

0 1 0

n4

0 1 1

n5

1 0 0

n6

1 0 1

n7

1 1 0

n8

1 1 1


CFW 09 - Technical Data

Power Supply

Voltage Three-phase:220-230 V: 220 230 V (+10% -15%)

380 - 480 V: 380 / 400 / 415 / 440 / 460 / 480 V (+10%, - 15%)500 - 600 V; 500 - 690 V; 660 - 690 V; 660/690 (+ 10%. -15%)

Frequency 50 / 60 Hz +/- 2 Hz (48 ... 62 Hz)Phase Unbalance Up to 3%

Cos (Displacement Power Factor) Greater Ihan 0.98 at full load

Enclosure

Degree of ProtectionNEMA 1/IP 20 (sizes 1...8 and 8E), IP20 (sizes 9,10 and 10E)

NEMA 4X I IP 56 (modules up to 10HP)

Finishing ColorPlastic Cover - Light Gray PANTONE 413 C (sizes 1 and 2)

Metallic Cover and Sides - Light Gray RAL 7032 (sizes 3 to 10)Base - Dark Gray RAL 7022 (sizes 3 to 10)

Control

Power Supply Switched Mode Power Supply Fed from the DC LinkMicroprocessor 32 bit RISC Technology

PWM TechniqueSVM Sine wave PWM (Space Vector Modulation)

Software Implemented Current fl ux and Speed Regulators (Full DigitaI)

Control ModesV / F

Sensorless Vector ( without encoder)Vector with Encoder

Switching Frequency 1.25 / 2.5 / 5.0 / 10 kHz

Frequency Range0...1020 Hz for V / Hz Control 0...408 Hz for Vector Control

Overload Capacity150% for 60 seconds every 10 minutes180% for 1 second every 10 minutes

Effi ciency Greater than 97% at full load

PerformanceSpeed Control

V / F ModeRegulation ( wilh Slip Compensation) : 1% 01 Motor Rated Speed

Resolution: 1 rpm ( Keypad Reference )Speed Regulation Range: 1: 20

SensorlessVector Mode

Regulation: 0.5% of Motor Rated SpeedResolution: 1 rpm (Keypad Reference)

Speed Regulation Range: 1:100

Encoder VectorMode

Regulation with:10 bit Analogy Reference: +1- 0.1% 01 Motor Rated Speed14 bit Analogy Reference: +- 0.01% 01 Motor Rated Speed

Digital Reference (Ex: Keypad): + / - 0.01 % of Motor Rated SpeedSpeed Regulation Range: Down to 0 rpm

Torque Control Vector ModesRegulation: + - 10% of Motor Rated TorqueRange: O ... 150% 01 Motor Rated Torque

Control Inputs

Analog2 Programmable Differential Input (10 bit) : 0...10 V 0...20 mA or 4...20 mA

1 Programmable Bipolar Input (14 bit): -10 ... + 10 V 0...20 mA or 4...20 mA <D1 Programmable Isolated Input (10 bit) : O ... 10 V 0...20 mA or 4...20 mA <D

Digital6 Programmable Isolated Input: 24 Vdc1 Programmable Isolated Input: 24 Vdc

1 Programmable Isolated Input: 24 Vdc (for Motor PTC Thermistor) Encorder 1 Isolated Differencial Encoder Signals Output: 5 ...15 Vdc External Power Supply

CommunicationSerial

RS-232 wilh KCS-GFW09 Kn <D - RS-485 Isolated with EBA or EBB Board <DProtocolo Johnson Contols-N2 (optional)

Fieldbus Modbus RTU Standard, Profi bus DP, DeviceNet, EtherNet / IP, DeviceNet Drive Profi le with KFB kits.

Safety Protections

D C Link Under Voltage Output Short CircuitD C Link Over Voltage Output Ground FaultDrive Over Temperature External FaultMotor Over Temperature SeIf -diagnosis Fault

Output Over Current Programming ErrorMotor Overload (i x t) Serial Communication Fault

Dynamic Braking Resistor Overload Motor or Encoder Connection FaultCPU / EPROM Error ( watchdog) Power Supply Ohase Fault (30 A and above models)

Encoder Fault Keypad Connection Fault

AmbientTemperature 0ºC (32ºF)...40ºC (104ºF), up to 50ºC (122ºF) with 2% / ºC (1,1% / ºF) output current derating

Humidity 5...90% Non CondensingAltitude 0...1000m (3300ft), up to 4000m (13100ft) with 10% / 1000m (3% / 1000ft) output current derating

Conformities

EMC Directive 89 / 336 / EEC - EM 61800-3 Elec tromagnetie Compatibil -Industrial Environment - EMC - Emission and ImmunitvLVD 73 / 23 / EEC low Voltage Directive

IEC 146 Semiconductor driveUL 508C Power Conversion EnuinmentEN 50178 Electronic Equipment for Use in Power InstallationsEN 61010 Safety Requirements for Electrical Equipament for Measurement Control and laboratory Use

Certifi cations

UL (USA) and cUL (CANADA) Underwriters laboratories Ine. USACE (EUROPE) Phoenix Test-Lab GmbH – Germany (Competent Body)

IRAM (ARGENTINA) Instituto Argentino de NormalizaciónC-Tiek (AUSTRALIA) 2250/1132383 Australian Communications Aulhority


CFW 09 - Technical Data

Keypad

Programming General Drive Functions ProgrammingControls Start/Stop , Increase/Decrease Speed, JOG, FWD/REV and Local/Remote

Monitoring

Speed Reference (rpm) Oulput Current (A)Motor Speed (rpm) Oulput Voltage (Vac)

Speed Proportional Value (Ex: ft/min) Drive StatusOutput Frequency (Hz) Digital Inputs StatusDC Link Voftage (Vdc) Transistor Outputs Status

Motor Torque (%) Relay Outputs StatusOutout Power (kW) Analog Inputs Value

Hours Powered Up (h) Four Last FaultsHours Enabled (h) Fault Messages

Control Features and Options

Standard

Keypad wilh LCD + LED displays (HMI-CFW09-LCD)Password to protect drive programming

LCD display language selection: English, Spanish and PortugueseControl mode selection (via parameter}: V / F. Sensorless Vector or Vector with Encoder

Fault auto-diagnosis and auto-resetParameters reset to factory or user default

Drive Self-tuning to motor and load (Vector Modes)Specifi c unit indication ( Ex: l/s, t/h, %, etc. )

Motor slip compensation (V / F Mode)Manual and automatic Torque Boost (V / F Mode)

Adjustable V / F Curve (V / F Mode)Minimum and maximum speed limits

Output current limitAdjustable motor overload protection

Digital gain and offset adjustments for the analog inputsDigital gain adjustment for the analog outputs

JOG functionJOG + I JOG - Function (momentary speed increase/decrease)

COPY Function (Drive ® Keypad or Keypad ® Drive)Comparison functions for lhe digital outputs: N* > Nx; N > Nx; N < Nx; N = O; N = N*; Is > Ix ; Is < Ix; T > Tx and T < Tx

Where: N = Motor speed; N* = Speed reference; Is = Output Current and T = Motor torqueLinear and S independent acceleration and deceleration ramps, two sets of ramps

DC BrakingOptimal Braking (Vector Modes)

Built-in dynamic braking transistor – Models up to 45A/220-230V and up to 30A/380-480V and up to 14A/500-600VMulti-speed function (up to 8 preset speeds)

Speed Profi ling functionHour meter and Wattrneter

Overlapping PID Regulator (for automatic control of level, pressure, fl ow, etc. )FWD I REV selection

Local I Remate operation selectionFlying Start function (restart with the motor spinning)

Skip Speed (critical speed rejection)Ride-Through (operation during momentary power loss)

Built-in dynamic braking transistor:Models: 6 ... 45 A / 220 - 230 V and 36 ... 30 A / 380 - 480 V

FieldBus communication: Modbus RTU built-in

Options

Simplifi ed keypad (with LED display only) HMI-CFW09-LEDIP 55 Remote keypad (LED display only) HMI-CFW09-LED-N4

IP 55 Remote keypad (LCD + LED displays) HMI-CFW09-LCD-N4Remote Keypad cable (3.3, 6.6,10.16.25 and 35 ft) CAB - HMI 09-X

Blank Keypad for local lnstallation TCL - CFW09Blank Keypad for remote installation TCR - CFW09

Remote Keypad frame kit KMR - CFW09

I/O Expansion Boards

EBA . OX - CFW09EBB .OX.- CFW09EBC1 .OX- CFW10EBE1. OX - CFW09

FieldBus Communications kits (Mounted inside drive)

Profi bus DP KFB - PDDeviceNet KFB - DN

DeviceNet Drive Profi le KFB - DDElherNet I IP KFB - EN

VSD I PC Communication kitSoftware SUPERDRIVE

KSD - CFW09Conectores e CabosKCS - CFW09

Intertace Serial Module RS-232 KCS - CFW09Built-in dynamic braking transistor

Models: 54...130 A / 220-230 V and 38...142 A / 380-480 V"DB" Models

External dynamic braking module

Models 180...600A/220-230V e 380-480V DBW - 01Models 107...472A/500-690V

DBW - 02Models 100...428A/660-690V

Easy mounting kit wilh fl ange (for sizes 3...8) KMF - CFW09Removable mounting kit (for slzes 9...10) KME - CFW09

Inductor kit for DC link (for sizes 2...8) KIL - CFW09EMC fi lter with high attenuation capacity RF

PAMENSKY 1 800 ASK 4 WEG (275-4934) Head Office1 877 PAMENSKY (726-3675) Provincial Office www.pamensky.com

V.J. Pamensky Canada Inc.

Toronto64 Samor RoadToronto, OntarioM6A 1J7

Montreal9428 boul du GolfAnjou, QuebecH1J 3A1

Winnipeg10 Hutchings StreetWinnipeg, ManitobaR2X 2X1

CalgaryBay #805100 - 64 Ave. S.E.Calgary, AlbertaT2C 4V3

Edmonton17204 - 114th Ave.Edmonton, AlbertaT5X 5Y7

Vancouver3226 - 138A StreetSurrey, British ColumbiaV4P 2B4

TEL: 416 781-4617FAX: 416 781-4352

TEL: 514 341-5950FAX: 514 341-2945

TEL: 204 633-1438FAX: 204 633-8720

TEL: 403 240-0629FAX: 403 240-0959

TEL: 780 444-4465FAX: 780 449-2543

TEL: 604 531-4004FAX: 604 531-7009

CAN.CFW09.12.2011

e = DC Bus Choke connection (Optional) (only from Size 2 and up)

e = DC Bus Connection

e = DB Resistor Connection (Up to Size 7 only. Option for Sizes 4 to 7)

CFW 09 - Block Diagram

Date post:	01-Dec-2018
Category:	Documents
Upload:	trinhcong
View:	242 times
Download:	0 times

CFW 09 - Pamensky 09 - Table of Products Notes: The maximum motor power ratings listed above are...

Documents