7/27/2019 CFX-Intro 14.5 L01 Introduction

http://slidepdf.com/reader/full/cfx-intro-145-l01-introduction 1/11

© 2012 ANSYS, Inc. December 17, 2012 1

14.5 Release

Lecture 01:

Introduction 

Introduction to ANSYS CFX

7/27/2019 CFX-Intro 14.5 L01 Introduction

http://slidepdf.com/reader/full/cfx-intro-145-l01-introduction 2/11

© 2012 ANSYS, Inc. December 17, 2012 2

Agenda: Day 1

Welcome to the ANSYS CFX introductory training course!

This training course covers the basics of using ANSYS CFX for performing a range of Computational Fluid Dynamic (CFD) analyses.

It is intended for all new or occasional ANSYS CFX users

Course Contents:

 – General understanding of the CFD process, and use of the CFX interface

 –Setting up a CFD simulation (materials, boundary conditions etc.)

 – Ensuring flow accuracy

 – Accounting for Turbulence and Heat Transfer

 – Postprocessing

7/27/2019 CFX-Intro 14.5 L01 Introduction

http://slidepdf.com/reader/full/cfx-intro-145-l01-introduction 3/11

© 2012 ANSYS, Inc. December 17, 2012 3

Agenda: Day 1

Morning Lecture 1 – Introduction

Lecture 2 – Introduction to Workbench

Lecture 3 – Introduction to CFD Methodology

Workshop 1 – Mixing Tee 

Lecture 4 – Domains, Boundary Conditions and Sources

Workshop 2 – Mixing Tee with Particles or

Workshop 3 – Mixing Tube (profile boundary condition)

Afternoon Lecture 5 – Post-processing 

Workshop 4 – Post-processing

Lecture 6 – Solver Settings & .out file

Workshop 5 – Airfoil

Lecture 7 – Summary/Review of Day

7/27/2019 CFX-Intro 14.5 L01 Introduction

http://slidepdf.com/reader/full/cfx-intro-145-l01-introduction 4/11

© 2012 ANSYS, Inc. December 17, 2012 4

Agenda: Day 2

Morning Lecture 8 – Interfaces and Moving Zones

Workshop 6 – Axial Fan Stage or

Workshop 7 – Centrifugal Pump

Lecture 9 – Heat Transfer

Workshop 8 – Electronics Cooling

Lecture 10 – Turbulence Modelling

Afternoon Lecture 11 – Transient Simulations

Workshop 9 – Tank Flush 

Lecture 12 – Best Practices for CFD 

Workshop 10 – Vortex Shedding 

Lecture 13 – CEL, CCL and Additional Variables

Lecture 14 – Summary/Review of Day

7/27/2019 CFX-Intro 14.5 L01 Introduction

http://slidepdf.com/reader/full/cfx-intro-145-l01-introduction 5/11

© 2012 ANSYS, Inc. December 17, 2012 5

More than 60 offices worldwide plus an extensive network of distributors

Over 2,200 direct employees of ANSYS and its subsidiaries worldwide

Listed on NASDAQ (ANSS)

Visit www.ansys.com for more information

About ANSYS, Inc.

Corporate HeadquartersCanonsburg, PA

7/27/2019 CFX-Intro 14.5 L01 Introduction

http://slidepdf.com/reader/full/cfx-intro-145-l01-introduction 6/11

© 2012 ANSYS, Inc. December 17, 2012 6

Breadth of Technologies

Structural Mechanics:

From Linear Statics

Fluid Mechanics:From Single-Phase Flows

Electromagnetics:

From Low-Frequency

Windings 

Systems:

From Data Sharing

To High-Speed Impact

To Multiphase

Combustion

To High-Frequency

Field Analysis

To Multi-Domain

System Analysis

7/27/2019 CFX-Intro 14.5 L01 Introduction

http://slidepdf.com/reader/full/cfx-intro-145-l01-introduction 7/11© 2012 ANSYS, Inc. December 17, 2012 7

Index and store CAE files automatically

Find and reuse past CAE files efficiently

Trace and audit simulation decisions 

Breadth of TechnologiesANSYS EKM - Engineering Knowledge Manager

ANSYS Engineering Knowledge Manager (EKM) is a multi-user collaborative

solution that is aimed at meeting the Simulation Process and Data Managementchallenges

Use Case:

Knowledge Retention and ReuseSimulation focused search and retrieval 

 Automated CAE reports

Remote CAE visualization

EKM capabilities

7/27/2019 CFX-Intro 14.5 L01 Introduction

http://slidepdf.com/reader/full/cfx-intro-145-l01-introduction 8/11© 2012 ANSYS, Inc. December 17, 2012 8

Build and run CAE workflows

Allow multi site, multi user access

Deploy templates for what if studies 

Breadth of TechnologiesANSYS EKM - Engineering Knowledge Manager

Use Case: Collaboration

Workflow Modeling

Process Tracking

Hosted Applications

EKM capabilities

ANSYS Engineering Knowledge Manager (EKM) is a multi-user collaborative

solution that is aimed at meeting the Simulation Process and Data Managementchallenges

7/27/2019 CFX-Intro 14.5 L01 Introduction

http://slidepdf.com/reader/full/cfx-intro-145-l01-introduction 9/11© 2012 ANSYS, Inc. December 17, 2012 9

The ANSYS Customer Portal

Contains over 50,000 support assets powered by a modern web user

interface and powerful search engine.

Support Products DownloadsKnowledge

Resources

Classroom Training

Webinars

Service Requests

Product Assets Latest Release

Updates

Tools

Previous Release(s)

Solutions

Conference Proceedings

Class3 Reports

Documentation

Training & Tutorials

support.ansys.com

7/27/2019 CFX-Intro 14.5 L01 Introduction

http://slidepdf.com/reader/full/cfx-intro-145-l01-introduction 10/11© 2012 ANSYS, Inc. December 17, 2012 10

About search

The ANSYS Customer Portal’s searchis powered by dedicated Google ®  

hardware.

Mesh = Meshed = Meshing

Export = Exported = Exporting

XXXXX = YYYYY = ZZZZZ

Example:You want a meshing tutorial for ANSYS Meshing and your search

has results for other products that are not of interest to you; by

selecting the product facet “ANSYS Meshing” you can narrow

down your results further.

Search Facets

7/27/2019 CFX-Intro 14.5 L01 Introduction

http://slidepdf.com/reader/full/cfx-intro-145-l01-introduction 11/11

© 2012 ANSYS, Inc. December 17, 2012 11

Support / downloads / training

Submit and review service requestsIf you cannot find the answer to your question within the ANSYS Customer Portal then

you can submit a service request. A member of ANSYS technical support will then get

back to you with advice or a solution.

Download the latest software and updates

Download ISO images if you wish to create a DVD which is recommend for installations

on multiple computers and allows you to keep an archive of the installation for later re-

use.

Individual downloads can also be selected if you have a limited speed internet

connection.

Download classroom and video training material

Training and tutorial material are available for both a broad range of ANSYS products

and user’s experience. Search the hundreds of courses available and improve your

knowledge of ANSYS software.