Page 1
TECHNICAL DATA SHEET
CH Designation: CH ANCHOR
Codes: ACHT, ACHT88, ACHT88E, ACHTA2, ACHINB, ACHINN, ACHE, ACHTPL, ACHTPI, ACHA, ACHG, ACHAFO, ACHGFO, ACHAA2, ACHGA2, ACHGE
Reference: FT CH-en Date: 06/07/18 Version: 13 Page: 1 of 9
CH-TO CH-8.8 CH-8.8 E CH-A2
CH-INB CH-INN CH-ES CH-PL
CH-PI CH-AR CH-GA CH-AF
CH-GF CH-AF A2 CH-GF A2 CH-GE
CHARACTERISTICS BASE MATERIALS
Metal anchor that works by expansion once installed with controlled torque.
Male thread.
Use in non-cracked concrete.
Easy assembly.
Assembled with built-in antispins in the collar ensuring a spin-free installation.
To be used for medium loads.
Installation through the material to be fixed.
Versions:
o Zinc plated bolt. o 8.8 bolt. o 8.8 bolt short sizes. o A2 stainless steel. o Tamperproof head bolt. o Black zinc-plated tamperproof head
bolt. o Projecting bolt. o Flat bolt.
o A2 stainless steel flat bolt. o Hook bolt. o Eye bolt. o Forged hook bolt. o Forged eye bolt. o Forged stainless steel A2 hook bolt. o Forged stainless steel A2 eye bolt. o Spiral hook bolt.
APPLICATIONS WEB DATA SHEET
For fixing signposts, shelves, panels, gates, railings, street furniture, fence posts, cinema and stadium seats.
Page 2
TECHNICAL DATA SHEET
CH Designation: CH ANCHOR
Codes: ACHT, ACHT88, ACHT88E, ACHTA2, ACHINB, ACHINN, ACHE, ACHTPL, ACHTPI, ACHA, ACHG, ACHAFO, ACHGFO, ACHAA2, ACHGA2, ACHGE
Reference: FT CH-en Date: 06/07/18 Version: 13 Page: 2 of 9
1. RANGE AND COMPONENTS
CODE PICTURE COMPONENT MATERIAL
CH-TO
Bolt Washer
Sleeve Antispin
Conical nut Surface treatment
DIN 931, class 6.8 DIN 9021 (M6, M20) special (M8 to M16) Carbon steel PVC Carbon steel Zinc plated ISO 4042 ≥ 5 μm
CH-8.8
Bolt Washer
Sleeve Antispin
Conical nut Surface treatment
DIN 931, class 8.8 DIN 9021 (M6), special (M8 to M16)
Carbon steel PVC
Carbon steel Zinc plated ISO 4042 ≥ 5 μm
CH-8.8 E
Bolt Washer
Sleeve Conical nut
Surface treatment
DIN 931, class 8.8 DIN 9021 (M6), special (M8)
Carbon steel Carbon steel Zinc plated ISO 4042 ≥ 5 μm
CH-A2
Bolt Washer
Sleeve Antispin
Conical nut
DIN 931, A2-70 DIN 9021 (M6, M20) special (M8 to M16) AISI304 AISI304 PVC AISI303
CH-INB
Bolt Sleeve
Antispin Conical nut
Surface treatment
Tamperproof hexalobular Tx recess 40 class 5.6 Carbon steel PVC Carbon steel Zinc plated ISO 4042 ≥ 5 μm
CH-INN
Bolt Sleeve
Antispin Conical nut
Surface treatment
Tamperproof hexalobular Tx recess 40 class 5.6 Carbon steel PVC Carbon steel Zinc plated ISO 4042 ≥ 5 μm
CH-ES
Projecting bolt Washer
Sleeve Antispin
Conical nut Nut
Surface treatment
Class 4.8 DIN 9021 (M6) special (M8 a M10) Carbon steel PVC Carbon steel DIN934 Class 6 Zinc plated ISO 4042 ≥ 5 μm
CH-PL
Bolt Sleeve
Conical nut Surface treatment
DIN 7991 class 10.9
Carbon steel Carbon steel Zinc plated ISO 4042 ≥ 5 μm
CH-PI
Bolt Sleeve
Conical nut
DIN 7991 A2-70
AISI304 AISI303
CH-AR
Hook bolt Washer
Sleeve Antispin
Conical nut Nut
Surface treatment
Class 5.6 C4D EN 10016-2
DIN 9021 (M6) special (M8 to M12) Carbon steel PVC Carbon steel DIN934 Class 6 Zinc plated ISO 4042 ≥ 5 μm
Page 3
TECHNICAL DATA SHEET
CH Designation: CH ANCHOR
Codes: ACHT, ACHT88, ACHT88E, ACHTA2, ACHINB, ACHINN, ACHE, ACHTPL, ACHTPI, ACHA, ACHG, ACHAFO, ACHGFO, ACHAA2, ACHGA2, ACHGE
Reference: FT CH-en Date: 06/07/18 Version: 13 Page: 3 of 9
CH-GA
Eye bolt Washer
Sleeve Antispin
Conical nut Nut
Surface treatment
Class 5.6 C4D EN 10016-2
DIN 9021 (M6) special (M8 to M12) Carbon steel PVC Carbon steel DIN934 Class 6 Zinc plated ISO 4042 ≥ 5 μm
CH-AF
Forged gook bolt Washer
Sleeve Antispin
Conical nut Nut
Surface treatment
Class 5.6 C4C EN 10263-2
DIN 9021 (M6) special (M8 to M10) Carbon steel PVC Carbon steel DIN934 Class 6 Zinc plated ISO 4042 ≥ 5 μm
CH-GF
Forged eye bolt Washer
Sleeve Antispin
Conical nut Nut
Surface treatment
Class 5.6 C4C EN 10263-2
DIN 9021 (M6) special (M8 to M10) Carbon steel PVC Carbon steel DIN934 Class 6 Zinc plated ISO 4042 ≥ 5 μm
CH-AF A2
Forged hook bolt Washer
Sleeve Antispin
Conical nut Nut
AISI304 DIN 9021 (M6) special (M8 to M10) AISI304 AISI304 PVC AISI303 DIN934 AISI304
CH-GF A2
Forged eye bolt Washer
Sleeve Antispin
Conical nut Nut
AISI304 DIN 9021 (M6) special (M8 yo M10) AISI304 AISI304 PVC AISI303 DIN934 AISI304
CH-GE
Eye bolt Washer
Sleeve Antispin
Conical nut Nut
Surface treatment
Class 5.6 C4D EN 10016-2
Special Carbon steel PVC Carbon steel DIN934 Class 6 Zinc plated ISO 4042 ≥ 5 μm
Page 4
TECHNICAL DATA SHEET
CH Designation: CH ANCHOR
Codes: ACHT, ACHT88, ACHT88E, ACHTA2, ACHINB, ACHINN, ACHE, ACHTPL, ACHTPI, ACHA, ACHG, ACHAFO, ACHGFO, ACHAA2, ACHGA2, ACHGE
Reference: FT CH-en Date: 06/07/18 Version: 13 Page: 4 of 9
PRODUCT RANGE ACCORDING TO DIAMETER:
* Special short sizes, no PVC collar
DIAMETER MODEL
8 9 10 11 12 14 16 20 25
CH
-TO
AC
HT0
8C
AC
HT0
8L
AC
HT0
9C
AC
HT0
9L
AC
H1
0C
AC
HT1
0L
AC
HT1
1C
AC
HT1
1L
AC
HT1
2C
AC
HT1
2L
AC
HT1
4C
AC
HT1
4L
AC
HT1
6C
AC
HT1
6L
AC
HT2
0C
AC
HT2
5C
CH
-8.8
/8.8
E
AC
HT8
808
E*
AC
HT8
808
C
AC
HT8
808
L
----
----
AC
HT8
810
E*
AC
HT8
810
C
AC
HT8
810
L
----
----
AC
HT8
812
C
AC
HT8
812
L
----
----
AC
HT8
816
C
AC
HT8
816
L
AC
HT8
820
C
----
CH
-A2
AC
HTA
208
C
AC
HTA
208
L
AC
HTA
209
C
AC
HTA
209
L
AC
HTA
210
C
AC
HTA
210
L
AC
HTA
211
C
AC
HTA
211
L
AC
HTA
212
C
AC
HTA
212
L
AC
HTA
214
C
AC
HTA
214
L
AC
HTA
216
C
AC
HTA
216
L
AC
HTA
220
C
----
CH
-IN
B/I
NN
AC
HIN
B0
8C
AC
HIN
N0
8C
AC
HIN
B0
8L
AC
HIN
N0
8L
---
---
AC
HIN
B1
0C
AC
HIN
N1
0C
AC
HIN
B1
0L
AC
HIN
N1
0L
---
---
----
----
----
----
----
----
----
----
CH
-ES
AC
HE0
8C
---
AC
HE0
9C
---
AC
HE1
0C
AC
HE1
0L
AC
HE1
1C
AC
HE1
1L
AC
HE1
2C
AC
HE1
2L
AC
HE1
4C
AC
HE1
4L
---
---
---
---
CH
-PL/
PI
AC
HTP
L08
C
AC
HTP
I08
C
AC
HTP
L08
L
AC
HTP
I08
L
---
---
AC
HTP
L10
C
AC
HTP
I10
C
AC
HTP
L10
L A
CH
TPI1
0L
---
---
AC
HTP
L12
C
AC
HTP
I12
C
AC
HTP
L12
L A
CH
TPI1
2L
---
----
----
----
----
----
CH
-AR
AC
HA
08C
---
AC
HA
09C
---
AC
HA
10C
---
AC
HA
11C
---
AC
HA
12C
---
AC
HA
14C
---
AC
HA
H16
C
---
---
----
CH
-GA
AC
HG
08C
---
AC
HG
09C
---
AC
HG
10C
---
AC
HG
11C
---
AC
HG
12C
---
AC
HG
14C
---
AC
HG
H1
6C
---
---
----
CH
-AF/
AF
A2
AC
HA
FO0
8C
AC
HA
A20
8C
---
---
---
AC
HA
FO1
0C
AC
HA
A21
0C
---
---
---
AC
HA
FO1
2C
AC
HA
A21
2C
---
---
---
---
---
---
----
CH
-GF/
GF
A2
AC
HG
FO0
8C
AC
HG
A2
08C
---
---
---
AC
HG
FO1
0C
AC
HG
A2
10C
---
---
---
AC
HG
FO1
2C
A
CH
GA
21
2C
---
---
---
----
---
---
----
CH
-GE
--- --- --- ---
AC
HG
E10
--- --- ---
AC
HG
E12
--- --- --- --- --- --- ---
Page 5
TECHNICAL DATA SHEET
CH Designation: CH ANCHOR
Codes: ACHT, ACHT88, ACHT88E, ACHTA2, ACHINB, ACHINN, ACHE, ACHTPL, ACHTPI, ACHA, ACHG, ACHAFO, ACHGFO, ACHAA2, ACHGA2, ACHGE
Reference: FT CH-en Date: 06/07/18 Version: 13 Page: 5 of 9
2. INSTALLATION DATA
DIAMETER
8 9 10 11 12 14 16 20 25
AC
H…
08
E*
AC
H..
.08
C
AC
H..
.08
L
AC
H..
.09
C
AC
H..
.09
L
AC
H..
.10
E*
AC
H..
.10
C
AC
H..
.10
L
AC
H..
.11
C
AC
H..
.11
L
AC
H..
.12
C
AC
H..
.12
L
AC
H..
.14
C
AC
H..
.14
L
AC
H..
.16
C
AC
H..
.16
L
AC
H..
.20
C
AC
H..
.25
C
d0: drillbit diameter [mm] 8 9 10 11 12 14 16 20 25
dW: plate diameter ≤ [mm] 9 10 12 13 14 16 18 22 27
h1: hole depth ≥ [mm] 40 45 60 45 60 45 60 80 60 80 75 100 75 100 85 110 110 130
hC: base material thickness ≥ [mm] 70 100 100 100 70 100 105 100 105 100 110 100 110 110 135 145 160
Tins: torque [Nm] 10 10 20 20 35 35 50 80 120
hef: efective depth ≥ [mm] 25 30 35 30 35 25 40 52 40 52 48 55 48 55 55 67 72 80
t fix
: fi
xtu
re t
hic
kne
ss ≤
CH-TO, CH-8.8, CH-A2, CH-ES
[mm] 5 15 5 15 5 15 5 15 5 25 5 25 5 25 15 25
CH-INB, CH-INN [mm]
--- 6.5 16.5 --- --- --- 6.5 16.5 --- --- --- --- --- --- --- --- --- ---
CH-PL, CH-PI [mm] --- 8 18 --- --- --- 9 19 --- --- 10 30 --- --- --- --- --- ---
CH-AR, CH-GA, CH-AF, CH-GF, CH-AF A2, CH-GF A2, CH-GE
[mm] ---
scr: critical anchors distance [mm] 75 90 105 90 105 75 120 155 120 155 145 165 145 165 165 205 215 240
ccr: critical edge distance [mm] 40 45 55 45 55 40 60 80 60 80 75 85 75 85 85 105 110 120
* Special short sizes, no PVC ring.
Page 6
TECHNICAL DATA SHEET
CH Designation: CH ANCHOR
Codes: ACHT, ACHT88, ACHT88E, ACHTA2, ACHINB, ACHINN, ACHE, ACHTPL, ACHTPI, ACHA, ACHG, ACHAFO, ACHGFO, ACHAA2, ACHGA2, ACHGE
Reference: FT CH-en Date: 06/07/18 Version: 13 Page: 6 of 9
3. PRODUCT INSTALLATION
1. DRILL THE HOLE
Check that the concrete is compact and porosity insignificant.
To be used in dry, wet and flooded holes.
Both drilling and hammering modes must be turned on in the drilling machine.
Hole diameter and length specified must be used.
2. BLOW AND CLEAN
It is necessary to clean the holes thoroughly free of dust and debris.
Air pump and brush must be used.
3. INSTALLATION
Anchor must be introduced into the hole until depth mark reaches the surface of the base material.
Hammer can be used if needed.
Anchor can be used both ways, through the hole of the material to be fixed or can be installed in advance.
4.TIGHTENING
Specified torque must be applied using a dynamometric wrench.
Page 7
TECHNICAL DATA SHEET
CH Designation: CH ANCHOR
Codes: ACHT, ACHT88, ACHT88E, ACHTA2, ACHINB, ACHINN, ACHE, ACHTPL, ACHTPI, ACHA, ACHG, ACHAFO, ACHGFO, ACHAA2, ACHGA2, ACHGE
Reference: FT CH-en Date: 06/07/18 Version: 13 Page: 7 of 9
4.- CHARACTERISTIC RESISTANCE
4.1.- Characteristic resistance* in C20/25 concrete** of an isolated anchor (no edge distance effect neither anchor distance effect) is indicated in the table below:
DIAMETER 8 9 10 11 12 14 16 20 25
CH
-TO
---
AC
HT0
8C
AC
HT0
8L
AC
HT0
9C
AC
HT0
9L
---
AC
H1
0C
AC
HT1
0L
AC
HT1
1C
AC
HT1
1L
AC
HT1
2C
AC
HT1
2L
AC
HT1
4C
AC
HT1
4L
AC
HT1
6C
AC
HT1
6L
AC
HT2
0C
AC
HT2
5C
Tension [KN] --- 7.5 9.1 7.5 9.1 --- 9.5 13.1 9.5 13.1 12.7 20.6 12.7 20.6 17.5 27.6 26.0 36.1
Shear [KN] --- 6.0 6.0 6.0 6.0 --- 12.8 11.0 12.8 11.0 16.8 20.6 16.8 20.6 20.6 25.3 47.1 72.1
CH
-8.8
AC
HT8
80
8E*
AC
HT8
80
8C
AC
HT8
80
8L
---
---
AC
HT8
81
0E*
AC
HT8
81
0C
AC
HT8
81
0L
---
---
AC
HT8
81
2C
AC
HT8
81
2L
---
---
AC
HT8
81
6C
AC
HT8
81
6L
AC
HT8
82
0C
----
Tension [KN] 5.3 7.5 9.1 --- --- 7.5 9.5 13.1 --- --- 12.7 20.6 --- --- 17.5 27.6 26.0 ---
Shear [KN] 7.4 8.3 8.0 --- --- 7.4 12.8 14.6 --- --- 16.8 20.6 --- --- 20.6 33.7 60.9 ---
CH
-A2
---
AC
HTA
20
8C
AC
HTA
20
8L
AC
HTA
20
9C
AC
HTA
20
9L
---
AC
HTA
21
0C
AC
HTA
21
0L
AC
HTA
21
1C
AC
HTA
21
1L
AC
HTA
21
2C
AC
HTA
21
2L
AC
HTA
21
4C
AC
HTA
21
4L
AC
HTA
21
6C
AC
HTA
21
6L
AC
HTA
22
0C
----
Tension [KN] --- 7.5 9.1 --- 9.1 --- 9.5 13.1 --- 13.1 12.7 20.6 --- 20.6 17.5 27.6 26.0 ---
Shear [KN] --- 7.0 7.0 --- 7.0 --- 12.8 12.8 --- 12.8 16.8 20.3 --- 20.3 20.6 29.5 55.0 ---
CH
-ES
---
AC
HE0
8C
---
AC
HE0
9C
---
---
AC
HE1
0C
AC
HE1
0L
AC
HE1
1C
AC
HE1
1L
AC
HE1
2C
AC
HE1
2L
AC
HE1
4C
AC
HE1
4L
---
---
---
---
Tension [KN] -- 7.5 -- 7.5 -- --- 9.5 13.1 9.5 13.1 12.7 20.6 12.7 20.6 -- -- -- --
Shear [KN] --- 6.0 -- 6.0 -- --- 12.8 11.0 12.8 11.0 16.8 20.6 16.8 20.6 -- -- -- --
CH
-IN
B/I
NN
---
AC
HIN
B0
8C
AC
HIN
N0
8C
AC
HIN
B0
8L
AC
HIN
N0
8L
---
---
---
AC
HIN
B1
0C
AC
HIN
N1
0C
AC
HIN
B1
0L
AC
HIN
N1
0L
---
---
---
---
---
---
---
---
---
---
Tension [KN] -- 7.5 10.1 -- -- -- 9.5 13.1 -- -- -- -- -- -- -- -- -- --
Shear [KN] -- 5.0 5.0 -- -- -- 9.2 9.2 -- -- -- -- -- -- -- -- -- --
CH
-PL
---
AC
HTP
L08C
AC
HTP
L08L
---
---
---
AC
HTP
L10C
AC
HTP
L10L
---
---
AC
HTP
L12C
AC
HTP
L12L
---
---
---
---
---
---
Tension [KN] -- 7.5 9.1 -- -- -- 9.5 13.1 -- -- 12.7 20.6 -- -- -- -- -- --
Shear [KN] -- 7.3 10.1 -- -- -- 12.3 18.3 -- -- 16.7 20.5 -- -- -- -- -- --
CH
-PI
AC
HTP
I08C
AC
HTP
I08L
---
---
AC
HTP
I10C
AC
HTP
I10L
---
---
AC
HTP
I12C
AC
HTP
I12L
---
---
---
---
---
---
Tension [KN] -- 7.5 9.1 -- -- -- 9.5 13.1 -- -- 12.7 20.6 -- -- -- -- -- --
Shear [KN] -- 7.0 7.0 -- -- -- 12.8 12.8 -- -- 16.7 20.3 -- -- -- -- -- --
Page 8
TECHNICAL DATA SHEET
CH Designation: CH ANCHOR
Codes: ACHT, ACHT88, ACHT88E, ACHTA2, ACHINB, ACHINN, ACHE, ACHTPL, ACHTPI, ACHA, ACHG, ACHAFO, ACHGFO, ACHAA2, ACHGA2, ACHGE
Reference: FT CH-en Date: 06/07/18 Version: 13 Page: 8 of 9
Notes: - 1KN ≈ 100 kg - * Special short sizes, no PVC ring. Values tested in C35/40 concrete. - Underlined and cursive letters indicate steel failure. - Characteristic tension load and shear load must be considered separately.
DIÁMETRO 8 9 10 11 12 14 16 20 25
CH
-AR
---
AC
HA
08
C
---
AC
HA
09
C
---
---
AC
HA
10
C
---
AC
HA
11
C
---
AC
HA
12
C
---
AC
HA
14
C
---
AC
HA
16
C
---
---
---
Tension [KN] --- 1.5 --- 1.5 --- --- 3.0 --- 3.0 --- 5.0 --- 5.0 --- 6.0 --- --- ---
Shear [KN] --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
CH
-GA
---
AC
HG
08
C
---
AC
HG
09
C
---
---
AC
HG
10
C
---
AC
HG
11
C
---
AC
HG
12
C
---
AC
HG
14
C
---
AC
HG
16
C
---
---
----
Tension [KN] --- 1.5 --- 1.5 --- --- 3.0 --- 3.0 --- 5.0 --- 5.0 --- 6.0 --- --- ---
Shear [KN] --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
CH
-AF
---
AC
HA
FO0
8C
---
---
---
---
AC
HA
FO1
0C
---
---
---
AC
HA
FO1
2C
---
---
---
---
---
---
----
Tension [KN] --- 4.2 --- --- --- --- 9.5 --- --- --- 12.7 --- --- --- --- ---- --- ---
Shear [KN] --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
CH
-GF
---
AC
HG
FO0
8C
---
---
---
---
AC
HG
FO1
0C
---
---
---
AC
HG
FO1
2C
---
---
---
----
---
---
----
Tension [KN] --- 1.7 --- --- --- --- 3.2 --- --- --- 5.9 --- --- --- --- ---- --- ---
Shear [KN] --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
CH
-AF
A2
---
AC
HA
A2
08
C
---
---
---
---
AC
HA
A2
10
C
---
---
---
AC
HA
A2
12
C
---
---
---
---
---
---
----
Tension [KN] --- 4.2 --- --- --- --- 9.5 --- --- --- 12.7 --- --- --- --- --- --- ---
Shear [KN] --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
CH
-GF
A2
---
AC
HG
A2
08
C
---
---
---
---
AC
HG
A2
10
C
---
---
---
AC
HG
A2
12
C
---
---
---
----
---
---
----
Tension [KN] --- 1.7 --- --- --- --- 3.2 --- --- --- 5.9 --- --- --- --- --- --- ---
Shear [KN] --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
CH
-GE
---
---
---
---
---
---
AC
HG
E10
---
---
---
AC
HG
E12
---
---
---
----
---
---
----
Tension [KN] --- --- --- --- --- --- 3.0 --- --- --- 5.0 --- --- --- --- --- --- ---
Shear [KN] --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
Page 9
TECHNICAL DATA SHEET
CH Designation: CH ANCHOR
Codes: ACHT, ACHT88, ACHT88E, ACHTA2, ACHINB, ACHINN, ACHE, ACHTPL, ACHTPI, ACHA, ACHG, ACHAFO, ACHGFO, ACHAA2, ACHGA2, ACHGE
Reference: FT CH-en Date: 06/07/18 Version: 13 Page: 9 of 9
4.2.- Recommended safety factors
SAFETY FACTOR RESISTANCE REDUCTION
LOAD INCREASE CONCRETE FAIL STEEL FAIL
ACHT Tension 1.80 ---
1.4
Shear 1.50 1.25
ACHT88 Tension 1.80 ---
Shear 1.50 1.25
ACHTA2 Tension 1.80 ---
Shear 1.50 1.56
ACHE Tension 1.80 --
Shear 1.50 1.25
ACHINB, ACHINN Tension 1.80 2.00
Shear --- 1.67
ACHTPL Tension 1.80 ---
Shear 1.50 1.50
ACHTPI Tension 1.80 ---
Shear 1.50 1.56
ACHA, ACHG,
ACHGE
Tension --- 1.50
Shear --- ---
ACHAFO, ACHGFO Tension 1.80 1.50
Shear --- ---
ACHAA2, ACHGA2 Tension 1.80 1.87
Shear --- ---
4.3.- Calculation example
- Fixing a tension 500 kg (4,91KN) load in C20/25 concrete using ACHT10L anchor. - Verification to be made: -
-
- Verification : fixture is safe - For more complex calculations INDEXcal calculation software can be used (download at www.indexfix.com ).
