August 2012 Issue 8
with Recommended Retail Prices
The Complete Flooring GuideThe Complete Flooring Guide
WELCOME TO THE WORLD OF WOODPECKER
WELCOME TO THE WORLD OF WOODPECKER
‘YOUR SATISFACTION GUARANTEED WITH
A 25 YEAR WARRANTY’
Each Woodpecker floor carries this outstanding reassurance of our
confidence that you will not find a better value product anywhere on the
market. Your satisfaction depends on our care and attention to detail,
such as the careful selection of the trees before they are felled and the
way in which the timber is sawn, stacked and dried.
In most cases the sawn timber is air dried for over twelve months prior
to a 2 stage kilning and dehumidification process to achieve maximum
stability. It is then carefully selected for grain pattern, colour variation
and knots, to provide the many varied appearances that are available
within the Woodpecker range. It is then machined using the latest
technologies – in many cases to engineering tolerances that up to a few
years ago would have been thought impossible – so we can bring virtual
perfection to your floor.
OUR COMMITMENT TO SUSTAINABILITY
We care about the environment and go to great lengths to bring to you
products that have been manufactured from materials harvested with
this in mind.
Stringent attention to all products right from the source to your door
gives you the assurance that with a Woodpecker floor you are not
impacting negatively on the environment.
Kenton Floors is a third generation family owned business who have been
involved in the timber industry for over a quarter of a century. Our motto
has always been:
‘THE BEST IS ONLY JUST GOOD ENOUGH’
At Kenton Floors ‘Affordable quality’ is no idle claim. Our traditional high
standards of selection and machining of every plank of flooring – instituted
in the original small factory where the first floors were made – are still
applied today now that our manufacturing facilities extend to thirteen
state of the art factories around the globe. Every board goes through a rigid
quality and grading process to ensure that the highest possible standards
are met to guarantee your perfect satisfaction.
‘TRADITIONAL HAND FINISHING TO ACHIEVE
A TIMELESS ELEGANCE’
The boards are then put through finishing processes such as lacquering,
oiling or antiquing – many of which are carried out by hand using centuries
old traditions – for that timeless elegance that only a natural wood floor
can bring to your home.
Finally it is stored in our extensive warehousing facility where we hold large
stocks ready for immediate dispatch to fulfil your requirements. All so that
you can enjoy the natural elegance of timeless tradition without delay once
you have made your selection.
We trust you will experience as much pleasure from your floor as we have
had in bringing it to you.
The Woodpecker Team
HOW TO CHOOSE THE RIGHT FLOOR 4
HOW TO CHOOSE THE RIGHT GRADE 5
HOW TO CHOOSE THE RIGHT HARDNESS 5
HOW TO CHOOSE THE RIGHT SURFACE FINISH 6
HOW TO CHOOSE THE RIGHT TRIMS 8
HOW TO CHOOSE THE RIGHT UNDERLAY 11
HOW TO CHOOSE THE RIGHT ADHESIVE 13
INSTALLATION: PREPARATION GUIDELINES 14
INSTALLATION: STICKING DOWN 16
INSTALLATION: FLOATING 18
INSTALLATION: SECRET NAILING 20
INSTALLATION: THE TRICKY BITS 22
UNDERFLOOR HEATING 24
ROUTINE FLOOR CARE 26
LONG-TERM FLOOR CARE 28
SOLID WOOD 30
YORK 31
DUNSTER 36
FLINK 38
DENBIGH 44
REAL WOOD ENGINEERED 46
RAGLAN 47
HARLECH 58
HARLECH MAGNUM 70
WINDSOR 74
CHEPSTOW 82
DESIGNER COLLECTION 92
GOODRICH 93
CHEPSTOW 96
ARUNDEL 100
BAMBOO 104
WARWICK 105
STYLE 108
CORK 114
ESTILO 115
LAMIN8 124
LAMIN8 125
VUSTA 144
PACK CALCULATOR 146
TERMS & CONDITIONS 147
HO
W TO
CHO
OSE
ENG
INEERED
CORK
SOLID
BAM
BOO
DESIG
NER
LAM
IN8
DISCLAIMER
Although every care has been taken in the reproduction of this catalogue,
each product has its own individual character. Variations will inevitably occur
in the colour and structure, and the physical limitations of the printing process
mean that we cannot guarantee your floor will look identical to the illustration.
SPECIFICATION DISCLAIMER
Kenton Floors reserves the right to change dimensions and grading specification
without notice. Customers should confirm that the floor of their choice is still
available with the specification shown.
PRICE DISCLAIMER
Prices can be changed without notice and should be checked prior to orders
being placed. No responsibility or liability is accepted by Kenton Floors for any
loss arising from such a change.
E&OE
While every effort is made to ensure that accurate pricing and descriptions
are given, we reserve the right to decline orders if they are based on inaccurate
information in this publication.
© Copyright 2012. No part of this catalogue may be copied or reproduced in
any way, without the express written permission of Kenton Floors. Nor may this
catalogue be used to sell or promote any products other than Woodpecker®.
INDEX
LAMINATE
Laminate simulates the appearance of a real wood fl oor without some
of the practical drawbacks. Its colour and characteristics are determined
by a decorative foil that is coated with a transparent melamine layer for
durability. The core is made of High Density Fibreboard (HDF) for optimum
strength and backed with a stabilizing cellulose paper.
TYPECHOOSE THE RIGHT FLOOR
SOLID WOOD
The traditional and timeless appeal of a solid wood fl oor will enhance
the appearance of any interior and endure for generations. Each board is
precision machined from a single piece of timber and typically fi nished
with a robust tongue and groove joint on all sides.
ENGINEERED
Each board is constructed from multiple layers of wood pressed together.
The top solid wood layer is available in a wide variety of species, fi nishes and
thicknesses to accommodate all tastes and requirements. It is supported by
a central core and backing board to give the fl oor increased stability.
ESTILO CORK
Innovative in design yet ecologically sustainable. Constructed of three
distinct layers for optimum comfort, warm and resilience. The prefi nished
cork top layer is laminated to a water-resistant HDF core which is backed
with a low density cork underlay for acoustic insulation.
BAMBOO
While technically a variety of grass, the characteristics of a bamboo fl oor are
comparable to that of a hardwood fl oor. Bamboo is 100% sustainable with
a life cycle of around 5 years. Available in two styles; traditional and strand-
woven, with the latter being twice as durable as the traditional method.
HO
W TO
CHO
OSE
4 HOW TO CHOOSE All prices include VAT
GRADE CHOOSE THE RIGHT GRADE
HARDNESS THE RIGHT HARDNESS
BAMBOO (STRAND WOVEN)
JATOBA
MERBAU
CANADIAN MAPLE
IROKO
BEECH
OAK
CHERRY
BAMBOO (ENGINEERED)
ASH
WALNUT
PINE
SOFTER HARDER
* Knots are divided into 2 main categories. A dead knot occurs when the
core has been removed or has fallen out. It is subsequently filled. A live
knot still has the core and generally does not contain filler. This grade
includes both categories. When knots are filled it is not always possible
to closely match the colour of the wood. If large knots with filler are not
wanted it is the responsibility of the customer to inform the installer to
cut these out at the time of installation.
SELECT
This grade offers a natural look with limited knots.
Considerable grain and colour variation provide a
characterful look. Up to 10% sapwood permitted
in some species but only small knots allowed.
RUSTIC
A rustic grade allows for considerable grain and
colour variation. Up to 10% sapwood, large knots*
(some filled); dark streaks and filled cracks are all
acceptable.
EXTRA RUSTIC
Very little is graded out in this category. Large
knots*, splits, cracks and any amount of sapwood
are all to be expected when choosing this
distinctive design.
HO
W TO
CHO
OSE
5HOW TO CHOOSEAll prices include VAT
FINISHING CHOOSE THE RIGHT SURFACE FINISH
UV OILED
An oiled finish penetrates the surface of the wood to bring out the natural
beauty of the grain. Each board receives 5–7 coats of oil and is UV cured at every
stage of the process. Choosing this finish allows for isolated areas of damage,
such as scratches, to be easily re-touched without the need for major work.
MATT LACQUERED
The dull satin sheen of the matt lacquered finish has been designed to
replicate the appearance of an oiled floor, without the same periodic
maintenance requirements. Instead its smooth hard surface enjoys the
same upkeep as a lacquered floor.
UV LACQUERED
A lacquered floor is typically smooth to touch and more glossy in
appearance. Each board receives 5–7 coats of lacquer and is UV cured at
every level of the process. The finished result is a hardwearing and durable
surface that can be easily maintained.
UNFINISHED
An unfinished floor has no surface finish which allows you to create
a truly bespoke result in terms of both colour and durability. All products
are supplied with pre-filled knots and the boards are pre-sanded for
your convenience.
IMAGE NEEDED
SAWN
Keeping you right in touch with nature, the kerf of the saw marks are proudly
exposed on each board producing that delightfully rustic feel that conjures
up the inspiring smell of fresh sawdust and the pleasure of witnessing
freshly sawn timber.
BRUSHED
The top of the board is lightly brushed to remove the softer surface fibres
and expose the wood grain. The result is a subtly textured finish that
delicately highlights the natural grain structure within the timber adding
definition to each plank.
HO
W TO
CHO
OSE
6 HOW TO CHOOSE All prices include VAT
BEVELLED EDGE
A bevelled edge adds definition to each plank creating a rustic feel that’s
more traditional in design. The chamfered edges will vary in size between
our different flooring collections, with anything from a discreet micro-bevel
right up to a deep v-groove.
SQUARE EDGE
The edges of each plank meet squarely when joined together, creating a
smooth and seamless transition between the boards. This results in a clean
and consistent overall finish that lends itself well to contemporary and
formal interiors.
HANDSCRAPED
Full of rustic charm, this distinctive finish is characterised by the unique textures
that result from the hand scraping process. Each plank is painstakingly scraped
by hand prior to finishing which creates an aged look. The irregular ridges and
grooves add depth and warmth yet remain smooth to the touch.
AGED & DISTRESSED
Each plank is hand distressed to produce a textured surface reminiscent
of a naturally aged, rustic floor. The boards are then subjected to a series
of caustic processes, such as smoking, before the application of oils and
stains to enrich their timeworn appeal.
HO
W TO
CHO
OSE
7HOW TO CHOOSEAll prices include VAT
TRIMS SELECTING THE RIGHT PROFILES
TWIN PROFILE
Covers the expansion gap between two floors of equal height, providing a neat finish at doorways or serving as a room divider.
RAMP PROFILE
Creates a smooth transition between two floors of varying height. Typically used to bridge larger transitions such as wood to vinyl floor coverings.
SEMI RAMP PROFILE
Provides a smooth transition between two floors of varying height.
Typically conceals minor transitions, such as wood to carpet.
PERIMETER PROFILE
Like the End Profile, the Perimeter Profile can also be used when
a wooden floor meets patio doors. With the option to scribe its rear
edge (if necessary), it is the ideal trim to finish a fireplace hearth.
For use with all Solid Wood and
Engineered flooring. Available in 3
heights and 13 finishes. Supplied in
lengths of 0.99m or 3m.
For use with all Solid Wood and
Engineered Flooring. Available in 3
heights and 13 finishes. Supplied in
lengths of 0.99m or 3m.
For use with all Solid Wood and Engineered flooring. Available in 3 heights
and 13 finishes. Supplied in lengths of 0.99m or 3m.
For use with all Lamin8 flooring.
Choose from 11 different colours,
supplied in lengths of 2.4m.
For use with all Lamin8 flooring.
Choose from 11 different colours,
supplied in lengths of 2.4m.
For use with Bamboo flooring.
Matching colours available for both
the Warwick and Style Flooring.
Supplied in 1.8m lengths.
For use with Bamboo flooring.
Matching colours available for both
the Warwick and Style Flooring.
Supplied in 1.8m lengths.
For use with all floor coverings but
primarily Estilo and Lamin8 flooring.
Available in Gold or Silver and
supplied in lengths of 0.99m and 3m.
For use with all floor coverings but
primarily Estilo and Lamin8 flooring.
Available in Gold or Silver and
supplied in lengths of 0.99m and 3m.
For use with all Solid Wood and Engineered flooring. Available in 3 heights
and 13 finishes. Supplied in lengths of 0.99m or 3m.
HO
W TO
CHO
OSE
8 HOW TO CHOOSE All prices include VAT
END PROFILE
Typically used as an attractive finish for an inset mat well. In some cases, it can also be used when a wooden floor meets patio doors.
STAIR NOSING
The Stair Nosing Profile is used on steps and stairs to protect the edges of the flooring from the excessive wear caused by foot traffic.
SCOTIA / QUADRANT
When it’s not possible to remove and refit skirting boards, the Scotia and Quadrant Profiles are used around the edge of a room to hide the necessary
expansion gaps.
For use with all Solid Wood and
Engineered flooring. Available in 3
heights and 13 finishes. Supplied in
lengths of 0.99m or 3m.
For use with all Solid Wood and
Engineered flooring. Available in
13 finishes. Supplied in lengths
of 1m or 3m.
Scotia and Quadrant Profiles are available for
use with all Solid Wood and Engineered flooring.
Available in 13 finishes and 3m lengths.
A Lamin8 Scotia Profile is available for use with all
Lamin8 flooring. Offered in 11 colours and lengths
of 2.4m.
A Quadrant Profile is available to match both
Warwick and Style bamboo flooring. Supplied in
1.8m lengths.
For use with all Lamin8 flooring.
Choose from 11 different colours,
supplied in lengths of 2.4m.
For use with all Lamin8 flooring.
Choose from 11 different colours,
supplied in lengths of 2.4m.
For use with Bamboo flooring.
Matching colours available for
the Style Range only. Supplied in
1.8m lengths.
For use with Bamboo flooring.
Matching colours available for both
Warwick and Style floor coverings.
Supplied in 1.8m lengths.
For use with all floor coverings but
primarily Estilo and Lamin8 flooring.
Available in Gold or Silver and
supplied in lengths of 0.99m and 3m.
For use with all floor coverings but
primarily Estilo and Lamin8 flooring.
Available in a Gold finish only.
Supplied in 2.5m lengths.
HO
W TO
CHO
OSE
9HOW TO CHOOSEAll prices include VAT
TRIMS SELECTING THE RIGHT PROFILES
SKIRTING BOARDS
Skirting serves as a smooth transition from floor to wall with the intention of concealing expansions gaps and unsightly wiring.
PIPE COVERS
Pipe covers are used to conceal the necessary expansion gaps and unsightly imperfections around the base of your radiator pipes.
SOLID OAK
Our dual purpose solid oak skirting allows you
to choose between a Torus and Ogee profile.
Made from rustic grade timber and available as
either a lacquered or unfinished board.
Finished size: 20 x 145 x 2400mm.
OAK VENEER
Our real oak veneered skirting offers a modern
pencil round profile with a moulded rear rebate
to conceal unsightly wires. Optional skirting clips
are available for a glueless installation.
Finished size: 16 x 95 x 2500mm.
LAMINATE
Our laminate skirting replicates a wide variety
of species and colours to compliment the
laminate floor of your choice. Simply order
the quantity required and we will do the rest!
Finished size: 15 x 80 x 2400mm.
SOLID
Hardwood pipe covers are supplied in two halves with a unique jigsaw design
that allows them to click together creating a seamless joint. Sold (pre-packed)
as pairs, with a set inside diameter of 15mm. Available in 7 prefinished
(lacquered) species as well as unfinished oak.
PLASTIC
Single piece, matt plastic pipe covers with laser incision for easy installation.
Simply slide the ring around the pipe and allow to snap into position. Sold in
packs of four and available in 6 different colours with a set inside diameter
of 15mm.
HO
W TO
CHO
OSE
10 All prices include VATHOW TO CHOOSE
UNDERLAY SELECTING THE RIGHT UNDERLAY
BASIC 20
Dense yet lightweight economy foam underlay offering a good degree
of comfort and support with reasonable sound and thermal insulating
properties. Minimal ability to correct subfloor irregularities. Ideal solution
when cost is important and in areas where moisture issues are of no
concern e.g. first floor bedrooms. To be used when floating a floor.
AQUASTOP
Designed especially for ground floor installations where excess moisture
could be present. Similar in specification to the Basic 20, with the addition
of a laminated Damp Proof Membrane (DPM) and 80mm overlap to ensure
ultimate protection against moisture migration. A popular and economic
solution when floating a floor.
UNDERMATE
Similar in specification to the Floormate, this low tog version has been
specifically designed for use with underfloor heating to allow maximum
thermal transfer. When installing over underfloor heating please ensure a
Damp Proof Membrane (DPM) is installed first to prevent moisture migration.
SOLITEC
A specialist underlay with a strong self-adhesive backing that enables both
a solid wood and engineered floor to be floated. No adhesive or nail gun
required! Always use in conjunction with a Damp Proof Membrane (DPM)
to protect against moisture migration.
FLOORMATE
High performance rubber underlay incorporating a foil vapour barrier to
prevent moisture migration. Designed to withstand heavy foot traffic. The
preferred option for all floating installations as it offers the best combination of
comfort and support together with sound and thermal insulating properties.
ACOUSTAMAT
A slatted acoustic underlay to be used in combination with the WP50
Adhesive Sausages and Bulk Gun as part of a liquid batten system. The pre-
cut areas provide a template for the adhesive and once installed it forms a
reliable acoustic barrier. Ideal for use on uneven subfloors.
DPM
DPM
HO
W TO
CHO
OSE
11All prices include VAT HOW TO CHOOSE
UNDERLAY SELECTING THE RIGHT UNDERLAY
MOISTOP BARRIER PAPER
Purpose made moisture resistant barrier paper for use when secret nailing a
wooden floor over a timber based subfloor. The bitumen backing self-seals
around the punctures formed by nails to maintain a watertight barrier and
help to prevent cupping or moisture migration.
XL UNDERLAY
Disguises minor irregularities within the subfloor by absorbing indentations
or protrusions up to 3mm in height. Made from lightweight extruded
polystyrene, the boards offer exceptional sound and thermal insulation as well
as moisture protection when taped together. To be used when floating a floor.
COIR MATTING
While technically not an underlay, coir matting should be an important
consideration when laying a new floor. It should be used at each entrance as
a barrier for wet and dirty feet to trap grit and prevent lasting damage. Grit
underfoot will have the same effect as sandpaper against your new floor.
BLUE DAMP PROOF BARRIER
An impermeable membrane designed to isolate a floor from damp
substrates. Its dimpled surface allows for air flow beneath the barrier making
it ideal for basements or recently screeded floors as it allows the substrate
to dry out without delaying the installation. This doesn’t negate the need to
check atmospheric humidity.
DAMP PROOF MEMBRANE (DPM)
A durable membrane designed to be used in combination with a cushioning
underlay to prevent the passage of moisture when floating a floor.
Manufactured from high quality polyethylene (1000 gauge), it has been
designed to provide superior strength and high puncture resistance.
DPM
DPM
DPM
DPM
HO
W TO
CHO
OSE
12 HOW TO CHOOSE All prices include VAT
ADHESIVE SELECTING THE RIGHT PRODUCTS
MS PARQUET
A purpose-made adhesive developed specifically for use with Woodpecker
floors. Designed to hold the boards after a short open time (30mins) but
remains permanently flexible once cured to allow for the expansion and
contraction of the timber between seasons.
FLOORING GRADE PVA
A premium flooring grade PVA adhesive for hardwood flooring.
Typically used when floating a floor to bond tongue and groove (T&G)
boards together. Easy to apply, solvent free and fully cured within four
hours of application.
11P SURFACE PRIMER
High performance surface primer used to seal dusty or porous substrates in
preparation for the Woodpecker MS Parquet adhesive, Woodpecker WP50
sausages, or the Woodpecker WP60 Liquid DPM. Improves adhesion on
difficult substrates.
WP50 SAUSAGES
A purpose-made adhesive designed for use with the slatted Acoustamat
underlay as part of a liquid batten system. Remains permanently flexible
once cured to allow for the expansion and contraction of the timber
between seasons. Apply using a gun applicator. Ideal solution for subfloors
with slight surface irregularities.
WP60 LIQUID DPM
A reliable liquid membrane designed to prevent residual moisture within
a screed from penetrating a new timber floor. Apply using a roller for a
seamless barrier. Fully cured within 30 minutes. Single coat application
when used in combination with the Woodpecker MS Parquet Adhesive.
LEVEL-X & PRIMER
A fibre-reinforced self-levelling compound designed to prepare and smooth
surface irregularities. Application may vary from 2–50mm in a single pour.
Substrates should be primed in advance to assist adhesion and prevent
contamination.
DPM
HO
W TO
CHO
OSE
13HOW TO CHOOSEAll prices include VAT
INSTALLATION PREPARATION GUIDELINES
PRE-DELIVERY CONDITIONS
Before any flooring is delivered to site, all wet trades such as concreting,
plastering and decorating should be complete and the building must be
thoroughly dried out. Windows and doors must be fitted and watertight.
N.B: As a rough guide, the drying time for a sand and cement
based screed is 1 day per mm for the first 50mm and 2.5 days per
mm thereafter. Therefore, a 50mm screed will take approximately
2 months to dry out while a 100mm screed could take about
6 months. Plaster may take 6 weeks or more to dry completely.
SUBFLOOR PREPARATION
Ideally the subfloor should be prepared for installation in accordance
with the industry standards outlined in BS-8201-2011. It must be in good
structural condition and free from damp rot, fungal or insect infestation
and contaminating residues. Surface irregularities should not exceed
3mm over a 2m area and the floor must be in a clean and vacuumed
condition. Hot pipes should be well insulated to prevent localised hot
spots under the floor that could lead to excessive shrinkage.
HEATING SYSTEMS
Before any flooring arrives on site, the room temperature and atmospheric
Relative Humidity (RH) must be stable. All heating and air conditioning
systems must be commissioned and operating for a minimum of 2 weeks
before fitting can commence.
Where underfloor heating is being used, we would always recommend
that a real wood engineered floor is installed in preference to a solid
wood floor due to the increased stability that a multi-layered construction
provides. Contractors that install solid wood flooring over underfloor
heating, do so at their own risk!
INSPECTION
Woodpecker flooring is subject to strict quality control procedures,
however, our products are manufactured from natural materials so it
is essential that you check every plank carefully before installation.
We cannot consider any claims regarding product defects after installation.
ACCLIMATISATION
Before installation, it is imperative that all flooring is acclimatised in the
room it is to be fitted. The sealed unopened boxes should be laid flat, ideally
in the centre of the room, or with at least 50cm distance from the walls.
Flooring must not be stored outdoors, in an outbuilding or a room displaying
ventilation, damp or condensation problems. The site conditions need to
match those which will prevail when the floor is in use.
– Solid wood flooring requires 5–7 days acclimatisation
– Engineered and bamboo flooring require 3–4 days
– Laminate and Estilo flooring only require 24 hours
LAYING DIRECTION
Wood flooring looks its best when the planks are installed in the same
direction as the light and down the length of the room. However, if your new
floor is to be laid upon existing parquet, the boards should be arranged at
right-angles to the existing floor.
Disclaimer: Installation guidance is advisory and based on established good practice and
BS-8201-2011. It is the responsibility of the installer to ensure that correct procedures are
followed before, during and after installation. Kenton Floors do not accept any reasonability
for any issues relating to installation.H
OW
TO CH
OO
SE
14 FITTING All prices include VAT
MOISTURE TESTING
While the surface of the subfloor may appear dry, it is possible
that excess moisture may still be present within the substrate.
As wood and moisture are natural enemies, it is imperative to test
the subfloor moisture content before fitting. Using a professional
moisture meter such as the Protimeter MMS, the readings must
not exceed the following:
– 70% Relative Humidity (RH) for cement based concrete
– 11% Wood Moisture Equivalent (WME) for wooden subfloors
or joists.
ATMOSPHERIC CONDITIONS
It is important that the following conditions are fulfilled before,
during and after the installation:
– Room temperature of at least 18°C (64°F)
– Floor surface temp. of at least 15°C (59°F)
– Atmospheric RH of between 40% and 60%
N.B: Wood flooring is not suitable for installation in wet rooms
or areas where there is a regular flow of water.
HO
W TO
CHO
OSE
15FITTINGAll prices include VAT
INSTALLATION STICKING DOWN YOUR FLOOR
A traditional tongue and groove wooden floor can be fixed
directly to a concrete subfloor using the Woodpecker MS
Parquet Adhesive. This purpose-made adhesive will hold
the timber after a short open time but remains permanently
flexible to allow for the expansion and contraction of the
timber between seasons.
The adhesive should be applied using a 3–4.8mm notched trowel
(depending on the condition of the subfloor) and spread evenly onto the
subfloor. It is essential that there is a full bond and that each board is fully
adhered to ensure maximum stability.
We always recommend that solid wood flooring is installed by an
experienced floor fitter. Wood is a natural product and susceptible to
dimensional changes – each situation needs to be professionally assessed
before installation commences.
N.B: Never glue the joints when fully sticking your floor down. It places too
much pressure on the boards and could lead to cracking.
Preparation Checklist
Are all wet trades complete and thoroughly
dried out?
As a rough guide, the drying time for a sand
and cement based screed is 1 day per mm
for the first 50mm and 2.5 days per mm
thereafter.
Is the subfloor clean, dry and free from any
contaminating residues?
If it is necessary to level the subfloor before
fitting, apply Level-X Primer followed by
Woodpecker Level-X (Fibre Reinforced)
Self-Levelling Compound. NEVER use latex
self-levelling compounds. They do not have
the tensile strength to resist the movement
of the timber.
Are the subfloor moisture readings
within tolerance?
A cement based screed must have an RH
(Relative Humidity) reading of 70% or less.
If there is any doubt as to the moisture levels
in the subfloor always apply the Woodpecker
WP60 Liquid Damp Proof Membrane which
will seal the moisture below the surface
of the floor and prevent the floor from
expanding and distorting. The subfloor must
be free of dust and any contamination before
application. Wooden subfloors must have
moisture readings of between 7% and 11%
WME (Wood Moisture Equivalent) and the
new flooring should be left to acclimatize
until it has reached a similar reading so as
to prevent undue expansion or contraction.
If the initial moisture readings are not within
tolerance then an alternative method for
fitting should be used.
Is the atmospheric RH reading between
40% and 60%?
If underfloor heating is present, has it been
properly tested and turned off 48 hours
before fitting?
Has the flooring been acclimatised for the
correct period of time?
HO
W TO
CHO
OSE
16 FITTING All prices include VAT
HO
W TO
CHO
OSE
17FITTINGAll prices include VAT
INSTALLATION FLOATING YOUR FLOOR
Floating a floor essentially means that the new boards are
loose laid over a suitable underlay instead of being screwed,
nailed or stuck to the subfloor.
A floating floor can be installed over various subfloors including concrete,
anhydrite, existing wood floor, chipboard, ceramic tiles, PVC and linoleum,
providing they meet the preparatory guidelines. Soft subfloor coverings such
as carpet must be removed.
Underlay should be laid edge-to-edge, in the opposite direction to that
of the flooring, and linked using an adhesive tape. If your underlay is dual-
purpose and also provides a Damp Proof Membrane (DPM), always use
the Woodpecker Vapour Tape to prevent moisture rising between the
seams. Do not overlap the underlay unless it has been specifically
designed to do so.
Starting in a corner of the room lay the first row of flooring with the tongue
(T&G) or top lip (Loc/Clic) of the board facing the wall. Don’t forget the
necessary expansion gaps! Ensure that all boards are tightly joined or glued
together, using a tapping block or pulling iron with care if necessary. The
off-cut from the final board in each row can be used to begin the next row,
providing it measures 200mm or more. To maximise the appearance of your
floor it is important to stagger the ends of the boards (header joints) by at
least 300mm.
Preparation Checklist
Are all wet trades complete and thoroughly
dried out?
As a rough guide, the drying time for a sand
and cement based screed is 1 day per mm
for the first 50mm and 2.5 days per mm
thereafter.
Is the subfloor level to within 3mm over
a 2m radius?
Minor undulations can be disguised using
the Woodpecker XL Underlay which will
help to absorb slight irregularities. However,
if it is necessary to level the subfloor before
fitting, apply Level-X Primer followed
by Woodpecker Level-X Self-Levelling
Compound.
Are the subfloor moisture readings
within tolerance?
A cement based screed must have an
RH (Relative Humidity) reading of 70%
or less while wooden subfloors must read
between 7% and 11% WME (Wood Moisture
Equivalent).
If there is any doubt as to the moisture
levels in the subfloor always use an underlay
with integral DPM (Damp Proof Membrane)
and install barrier side down to form a
protective layer.
Is the atmospheric RH reading between
40% and 60%?
If underfloor heating is present, has it been
properly tested and turned off 48 hours
before fitting?
Has the flooring been acclimatised for the
correct period of time?
HO
W TO
CHO
OSE
18 FITTING All prices include VAT
LOC SYSTEM
Although not always viable, fi tting is easiest
when you ‘loc’ down the boards in complete
rows rather than individually. When connecting
the header joints, insert the board into the lip
at an angle of 30° then simultaneously move
the board closer and lower into position. The
fl ooring should ‘loc’ into place. Never use force;
instead remove the board and check for dirt or
excess lacquer then try again.
CLIC SYSTEM
When installing, align the long edge of the
board fi rst and simply ‘clic’ into position. Using
a tapping block, gently knock the header joint
up towards the previous board until they
snap together. Remember, these instructions
are advisory and you may fi nd that, for you,
installation is still easier if the header joints
are connected prior to the long edges and the
whole run inserted together
TONGUE AND GROOVE
When gluing a tongue and groove board, run
a generous bead of adhesive along the lower
groove of both the long-side and header joint.
This will provide a suffi cient bond between
the boards and eliminate squeaking. To fi x into
place, slide towards the long edge with the
header joint connected and tighten using a
tapping block or pulling iron as necessary.
HO
W TO
CHO
OSE
19FITTINGAll prices include VAT
INSTALLATION NAILING DOWN YOUR FLOOR
A traditional tongue and groove wooden floor can be
secret nailed over an existing timber subfloor or (subject
to thickness) fixed directly above joists to provide a
structural floor.
Current building regulations stipulate that a structural floor must exceed
18mm in thickness. Where possible it is recommended that a structural
timber based sheet material is installed over the joists ahead of the flooring
being fitted to avoid any surface irregularities.
Whichever method you use, the subfloor must be of an appropriate
width and thickness to retain a 50mm cleat when fired into it at 45°.
Joists must be kiln dried to avoid cupping or expansion and must be
spaced in accordance with current building regulations (we recommend
300mm centres).
When secret nailing always use the Woodpecker Moistop Barrier Paper over
the subfloor and overlap the joins by a minimum of 200mm. The bitumen
backing self-seals around the punctures formed by nails to maintain a
watertight barrier. It may be necessary to secure the joins with a moisture
resistant tape.
Flooring should be fitted at 45° or 90° to the subfloor and nailed over every
joist – through the sheet material if applicable. It is possible to have header
joints which are not over a joist providing the boards either side are fully
spanning the joists. Cleats should be no more than 400mm apart.
N.B: Never use adhesive to glue the joints in combination with this method.
Preparation Checklist
Are all wet trades complete and thoroughly
dried out?
Is the subfloor structurally safe and free
from damp rot, fungal or insect infestation?
Is the subfloor clean, free of chips or
shavings, dry and level to within 3mm over
a 2m area?
Will the subfloor retain a 50mm cleat when
fired into it at 45°?
If necessary, have all hot pipes been
insulated to prevent hot spots?
If underfloor heating is present, has it been
properly tested and turned off 48 hours
before fitting?
Does the subfloor measure between 7% and
11% WME (Wood Moisture Equivalent)?
Wooden subfloors must have moisture
readings of between 7% and 11% WME
(Wood Moisture Equivalent) and the new
flooring should be left to acclimatize until it
has reached a similar reading so as to prevent
undue expansion or contraction.
Is the atmospheric RH reading between
40% and 60%?
Has the flooring been acclimatised for the
correct period of time?
HO
W TO
CHO
OSE
20 FITTING All prices include VAT
HO
W TO
CHO
OSE
21FITTINGAll prices include VAT
INSTALLATION THE TRICKY BITS
THE FIRST ROW
After determining the best layout of the flooring and the starting wall,
measure the width of the room and divide it by the width of the flooring
panels to determine the number of rows and the width of the last row.
If the last row is determined to be less than 60mm wide, it should be
adjusted by cutting the first row lengthwise.
– Check all panels for possible damages/defects.
– Starting from the left hand corner of the room lay the first row of
flooring with the tongue (T&G) or top lip (Loc/Clic) of the board
facing the wall.
– Place spacers between the edge of the flooring panels and the wall
to provide an appropriate expansion gap.
– Mark then cut the last panel in the first row to the required length.
Use the remainder of the board to start the second row of flooring
– Always make sure the off-cut is at least 200mm in length. If not,
cut another piece greater than 200mm in length.
– Start all subsequent rows with the off cut piece from the previous row.
N.B: Ensure all the short ends are staggered at least 300mm. It is vital
to maintain a minimum of 300mm between the ends of boards in the
adjacent rows (staggered).
PIPES
Measure the position of the pipes and mark it on the panel, consider also
the expansion. Take measurements from the spacers into account. Drill a
hole 16mm (5/8”) bigger than the pipe diameter expansion provision. Saw
at a 45degree angle to the holes. Apply glue to the sawn out piece and fit in
with the pull bar. Again, do not forget the spacers.
DOOR JAMB
If you have a wooden door jamb, we recommend undercutting the door
jamb according to the thickness of the flooring plus the possible underlay.
Install the flooring underneath the doorjamb but leave the necessary
expansion gaps!
HO
W TO
CHO
OSE
22 FITTING All prices include VAT
EXPANSION GAPS
Since wood flooring is a natural material, it is subject to shrinkage and
expansion due to changes in climate conditions. Therefore, expansion
gaps must be left when a floor meets obstructions such as walls,
doorframes, structural supports, stairs, fireplaces or pipes. Spacers
should be placed at regular intervals when fitting and removed before
skirting boards or trims are installed to conceal the gaps.
For wood flooring it is necessary to leave at least 2mm for every 1m
span across the board with a minimum of 10–15mm regardless. For
particularly large areas exceeding 8 metres in width (or 5 metres
in width for a solid wood floor) it is recommended that additional
expansion provision should be allowed by the inclusion of washer or
penny joints at appropriate intervals across the floor. For Lamin8 and
Estilo flooring, a minimum of 8mm expansion is required.
N.B: Skirting boards should always be fixed to the wall and must
not in any way obstruct the movement of the floor.
HO
W TO
CHO
OSE
23FITTINGAll prices include VAT
FLOOR HEATING UNDERFLOOR HEATING
CHOOSING A FLOOR
In general we would always recommend that where underfloor heating
is being used, then a Real Wood Engineered floor should be installed in
preference to a Solid Wood floor due to the increased stability that
a multi-layered construction provides.
Not all timbers react well with underfloor heating so it is important to
choose one of the floors that is recommended for use with underfloor
heating. Each floor in this catalogue carries a recommendation in the
listing next to the product as to its suitability.
CHECK YOUR SUBFLOOR
You must NEVER install underfloor heating over a concrete subfloor
that has a moisture content of more than 75% Relative Humidity (RH).
Ideally we would recommend it to be below 70% RH to give a margin
for error.
In the case of timber subfloors, it is important that the moisture content
does not exceed 11% Wood Moisture Equivalent (WME). Make sure
your installer has checked these readings before proceeding.
If the measurements exceed the above guidelines, then one of the
Woodpecker damp proof preparation products must be used prior to
installation of the heating system.
PICK YOUR SYSTEM
There are two main types of system available with many variations from
different manufacturers, but essentially they will either be water heated
or electrically heated systems.
In general, water heated systems are normally found in new build or
renovation projects, while electrically heated systems are generally found
in situations where installation is required to be relatively quick and easy.
Whichever system you choose, the maximum water or electrical element
temperature should not be greater than 50°C and the temperature below the
floor must never exceed 27°C.
TEST YOUR HEATING
Prior to fitting your floor, the underfloor heating should, in the case of a water
heated system, be fully pressurised, tested for leaks and left to run usually for
a fortnight, but certainly until all the moisture in the screed or timber subfloor
has been driven off.
Plaster should be dry and all the wet trades finished in the rooms to which the
flooring is to be fitted. The atmospheric Relative Humidity within the room
should read between 40% and 60%.
FITTING YOUR FLOOR
Your underfloor system should be turned off for at least 48 hours prior to
fitting the floor. Only electrical heating or central heating should be used
during installation.
Engineered tongue and groove floors (subject to suitability of species) should
always be fully adhered to the subfloor using the Woodpecker MS Parquet
(Flexible) Adhesive.
An Engineered floor with a glueless locking joint can, in most cases, be floated
over underfloor heating subject to suitability of species. Remember to pick an
underlay that is suitable for use with underfloor heating.
If only part of the subfloor has underfloor heating, the new flooring must not
be laid continuously but separated by dilation joints because flooring installed
over underfloor heating is likely to expand and contract more than flooring
that is not.H
OW
TO CH
OO
SE
24 FLOOR HEATING All prices include VAT
AFTERCARE
After fitting, the floor should be left for 2–3 days
to fully acclimatise to its new surroundings and if
relevant for any adhesive to fully cure before the
heating is switched on.
When ready, the heating should be raised gently
by 1°C per day from the prevailing ambient
temperature. It must NOT be turned on full
straight away.
Raising and lowering the temperature of your
heating too quickly can result in dimensional
changes to the timber which will cause the floor
to shrink and crack.
As a general rule, this method of gradually increasing
and decreasing temperatures should be followed in
the day-to-day running of your system. Ideally,
underfloor heating should be left running from the
thermostat all the time and only raised or lowered by
1°C per day to accommodate the different seasons.
MORE INFO
These guidelines are not exhaustive and are provided
to give a general understanding of how the systems
work. They do not replace the need to follow the
recommended fitting procedures of each individual
manufacturer.
CONCRETE SCREED
WOODPECKER UNDERMATE
WOODPECKER DAMP PROOF MEMBRANE
1°C per day
HO
W TO
CHO
OSE
25FLOOR HEATINGAll prices include VAT
FLOOR CARE ROUTINE CARE & MAINTENANCE
ROUTINE CARE
We appreciate that hardwood flooring is a major investment for most
people and knowing how to clean and maintain your floor is paramount
in retaining its natural beauty and ensuring longevity.
LIGHT CLEANING
Wooden floors can either be swept regularly using a soft bristled broom
or vacuumed frequently to remove any dirt and gr t. When vacuuming
your floor, it is advisable to use a soft brush attachment to minimise
scratching.
PETS
Wooden floors hold many advantages for pet owners but inevitably
animals can damage your floor. Keep claws trim to prevent scratches
and mop any ‘accidents’ immediately to avoid staining. Opting for a light
coloured floor will minimise the appearance of scratches, while an oiled
finish will allow you to easily carry out spot repairs if necessary.
SPILLAGES
Since water and wood are natural enemies, any spillages should be
removed promptly! While small drops of water may not harm your floor,
excessive amounts of water left sitting on the boards are likely to cause
lasting damage.
SHOES
As a rule of thumb, stilettos should be left at the front door and heavy
shoes avoided! High heels and stilettos in particular, exert a phenomenal
pressure that even the toughest of timber species struggle to withstand.
SUNLIGHT
Exposure to direct sunlight will cause your floor to mellow in colour
over time. Red woods like Merbau, Jatoba, Cherry etc., are particularly
susceptible to colour change. Be sure to frequently move rugs and
mats placed in these areas to ensure the floor colour matures evenly.
PROTECTION
Prevention rather than cure is the key to a beautiful floor! Consider using
rugs or carpet runners in high traffic areas such as hallways and never
drag furniture or other objects across a wood floor. Woodpecker offers
a variety of felt protectors and castor cups that will allow furniture to be
moved with ease and without marking your floor.
FLOOR MATS
Install good quality floor mats at each entrance to trap dirt and prevent
damage. Grit underfoot will act like sandpaper against your floor.
Woodpecker Coir Matting is an ideal entrance barrier for wet and dirty feet.
HO
W TO
CHO
OSE
CLEANING PRICE LIST
Woodpecker Cleaning Kit77-WRC-001 Oiled Floors £27.90
77-WKL-001 Lacquered / Lamin8 £27.90
Woodpecker Cleaner Refill77-WKO-001 Oiled Floors £11.90
77-WLC-001 Lacquered / Lamin8 £11.90
77-WRC-001 Washable Mop Head £11.90
Woodpecker One Coat Soap81-OCS-002 Oiled Floors (2 Litre) £41.90
Heavy Duty (Self Adhesive) Felt Pads 05-FFP-951 Round (19mm) £4.80
05-FFP-952 Round (25mm) £4.80
05-FFP-953 Round (38mm) £4.80
05-FFP-947 Multi-pack (various sizes) £11.50
05-FFP-950 2 pads (113x153mm) £7.40
26 All prices include VATFLOOR CARE All prices include VAT
MOPPING
Always use a well rung mop when wiping your
hardwood floor. Excess liquid has the potential
to seep down the joins in a floor and cause
permanent damage.
Specially formulated for Woodpecker floors are
our comprehensive Cleaning Kits, containing an
antistatic mop, cleaning fluid and trigger head
spray bottle for easy application. The cleaning kits
are offered for both lacquered and oiled finishes,
with product refills available as necessary.
In addition to the above kits, Woodpecker One
Coat Soap is a concentrated cleaning solution
exclusively for oiled floors. Once diluted, it is applied
in a similar fashion to the above. Repeated use
of Woodpecker products on oiled floors will help
develop an invisible film, offering extra protection
and increased resistance to dirt.
HO
W TO
CHO
OSE
27FLOOR CAREAll prices include VAT
FLOOR CARE LONG–TERM CARE & MAINTENANCE
LONG-TERM CARE
Despite using some of the most advanced finishing products and
techniques on the market, a hardwood floor will not withstand the brunt
of daily life forever. Eventually, even the most well-tended of surfaces will
require a little extra maintenance.
It is important to maintain an existing floor finish in good time. If you
allow the protective coat to wear away, it becomes susceptible to dirt
and water which can penetrate the surface of the wood making the
floor difficult to clean and quickly subdued. Routine maintenance is
particularly important for floors with distinctive finishes, as sanding
will take out all traces of an existing stain or texture.
Due to individual circumstance, it is impossible to recommend how
often you should renew your floor finish but as a preventative measure,
you may wish to recoat the floor every 2–3 years. To perform a basic
evaluation of your floor finish, select a high traffic area and pour a few
drops of water onto the floor. A well finished floor will force beads of
water to form on the surface suggesting that no maintenance is required.
If the water slowly soaks into the timber leaving behind a light saturation
mark, the finish is only partially effective and a new coat of lacquer or
oil should be applied. Alternatively, if the water is immediately absorbed
leaving behind a dark stain, it indicates that the finish has completely
worn and the floor may need to be sanded and recoated.
Methods of repair will differ depending on whether your chosen floor
was pre-treated with an oil or polyurethane lacquer. If you are unsure,
as a general rule of thumb a lacquered floor is typically smooth and
shiny while an oiled floor has a matt finish and subtle texture.
However, before any surface treatment is carried out, we always
recommend that an adhesion test is performed in an inconspicuous
area to determined compatibility.
Unfortunately, a laminate floor cannot be repaired in the same way that a
hardwood floor can, however, small chips and scratches can be concealed
using the Colourfill Repair Kit. The kit is supplied together with a solvent to
clean the affected areas before filling and to remove excess filler afterwards.
OILED FLOORS
Unlike a lacquered floor, an oiled surface allows for isolated areas of damage,
such as scratches and stains, to be easily re-touched without having to re-oil
the entire floor. Although easier to repair, they usually require earlier periodic
maintenance.
ONE COAT SOAP
The One Coat Soap is a concentrated cleaning solution specially designed
for oiled floors. When diluted with 150mls of water, it can be used in the
same fashion as the Woodpecker Maintenance Kits. However, on occasion
it can also be used as neat solution to perform a deep clean. If this fails
to revive the floors natural lustre then you will need to consider re-oiling
your floor.
ONE COAT CLEANER
Before re-oiling all or part of your floor, it is essential that the wood is
free from dust and contamination to ensure adhesion. Applying a small
amount of the One Coat Cleaner to a dry cloth is sufficient enough to
intensively clean the affected area. It also allows for any dust to be collected
electro-statically. Drying times will vary from 15–60 minutes depending
on saturation. If the floor remains soiled, you will have to consider sanding
the surface to remove the engrained dirt.
ONE COAT OIL
Using a cotton cloth, brush or squeegee, the oil is applied sparely and
evenly to the floor and worked into the wood along the grain. The oil only
needs 60 seconds to react with the floor and the excess must be rubbed off
within 15–20 minutes of application, until practically dry. With such a quick
response time required, it is important not to expand treated areas beyond
your resources. One Coat Oil is also suitable for commercial properties
without the need for multiple coats. Its ability to re-disperse on the surface
of the wood also eliminates tide marks and any signs of overlapping.
Approximately 24–36 hours after application, the floor is suitable for
foot traffic.
HO
W TO
CHO
OSE
28 FLOOR CARE All prices include VAT
HO
W TO
CHO
OSE
LACQUERED FLOORS
Small indentations and isolated scratches can be concealed and
recoated using the Woodpecker Touch-Up Lacquer. Before application,
ensure that the area in question is dry and free from dirt, dust or grease.
Using the brush applicator supplied within the lid, paint the lacquer
onto the affected area and leave to cure.
To disguise deeper scratches or gouges, you many need to use a
professional wood floor filler. Available in a wide variety of colours from
most hardware or flooring retailers, these pastes are applied to the
damaged area, left to cure, sanded flush and later sealed using the
Touch-Up Lacquer to maintain a protective shell.
When it comes to restoring your entire floor, the Ultimo Lacquer is available
in two grades to cater for both domestic and commercial environments.
A factory lacquered floor will not need to be sanded back prior to application,
however, previously re-lacquered surfaces must be lightly sanded to ensure
sufficient adhesion.
Unlike an oiled floor, the lacquer doesn’t penetrate the surface of the wood
so the entire floor must be re-lacquered to prevent the formation of ridges.
Best results are achieved using a roller. A single coat is sufficient enough to
protect against moisture although several coats may be applied if the floor is
subject to high levels of foot traffic. When coating unfinished timber, three
coats of lacquer are required. Between each coat of lacquer, the floor must
be sanded, vacuumed and wiped with a damp cloth before re-coating.
The lacquer will take about 1–2 hours to dry between applications.
After 24 hours the floor is suitable for light foot traffic, although the
surface will continue to cure for 7 days before rugs can be replaced.
CLEANING PRICE LIST
Oiled Floors81-OCS-002 Woodpecker One Coat Soap 2 ltr £41.90
81-OCC-001 Woodpecker One Coat Cleaner 1ltr £27.90
81-OCO-001 Woodpecker One Coat Oil Pure £83.90
Lacquered Floors02-TUL-080 Touch Up lacquer 30ml Silk Matt £11.90
02-TUL-081 Touch Up lacquer 30ml Matt £11.90
52-WUL-004 Woodpecker Ultimo Floor Lacquer £63.00
52-WUP-004 Woodpecker Ultimo Plus Floor Lacquer £85.00
Laminate Floors06-UCF-005 Colourfill with solvent Oak £12.95
06-UCF-176 Colourfill with solvent Dark Oak £12.95
06-UCF-043 Colourfill with solvent Light walnut £12.95
29All prices include VAT FLOOR CARE
SOLID WOODFOR THE ULTIMATE HARDFLOOR EXPERIENCE
For many centuries timber has been used as a
fl ooring material and evokes an atmosphere of
timeless elegance and charm which will add
character to any home or building.
In the following pages you will fi nd a variety of
solid wood fl oors from as far afi eld as Russia, the
Far East, North and South America, Eastern and
Western Europe.
Each is treated in diff erent ways to bring out the
natural qualities of the material and complement
the unique style of your home.
Each board is made from a single piece of timber,
usually with a tongue and groove joint, on the
ends as well as the long side. This is called ‘Ends
Matched’ and ensures that your fl oor is secured
fi rmly to the subfl oor and gives maximum stability.
The choices of fi nish that are outlined on page 8
will further enhance the fi nished look of your fl oor
and will provide you with a fl oor that not only
provides pleasure and enjoyment but will prove
to be an investment that enhances the value and
attractiveness of your property.
We only source our products from managed
forests where there is a commitment to
sustainability – when you buy from Woodpecker®
you may be sure that your children’s children will
enjoy an enduringly beautiful fl oor, and also an
unspoilt environment for many years to come.
We strongly recommend that once you have
chosen your solid wood fl oor that you use an
experienced fl oor fi tter who has the necessary
experience and means to test the atmospheric
and subfl oor moisture levels in your property.
This is very important as wood is homogenous
and will take on and give off moisture which in
turn will cause it to expand or contract depending
on moisture levels. It is important therefore that
the prevailing conditions are taken into account
prior to installation.
It is also important to note that it is normal to
expect some movement within a solid wood fl oor
due to seasonal changes in humidity which will
normally settle down once a fl oor has been down
for a year or so.
SOLID
30 SOLID WOOD All prices include VAT
York is a traditional tongue and groove solid wood fl oor,
manufactured from either European Oak or American Black
Walnut, with variable lengths ranging from 300–1500mm.
Finished with 5 coats of highly wear resistant lacquer this
product represents excellent value for money.
When deciding whether to have a solid or an engineered wood
fl oor, you need to consider the environment in which it will be fi tted.
How will it be fi tted? Will it be nailed down or stuck down?
Are you satisfi ed that the moisture levels within the subfl oor are
at the correct level? Please refer to our fi tting pages.
YORKTRUE BEAUTY – REAL VALUE
YO
RK
5 COATS OF DURABLE UV LACQUER
TONGUE AND GROOVE JOINT
MANUFACTURED FROM SOLID OAK
STRESS GROOVES
MATCHING TRIMS AVAILABLE BEVELLED EDGES
36-YNO-00136-YOR-00136-YRO-001
36-YWR-00136-YBM-004 36-YOA-003
SOLID
31SOLID WOODAll prices include VAT
Sourced from extensive Oak forests across Europe...
York Oak
Rustic Plank
TYPE OF FLOOR Solid Wood
THICKNESS 18mm
LENGTH X WIDTH 300–1500mm x 90/130mm
average length 700mm
PACK SIZE 1.584m2 / 2.29m2
TYPE OF FINISH Lacquered or Oiled
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Stick down or secret nail
UNDERFLOOR HEATING Not advised
HARDNESS Hard
DURABILITY High wear resistance
York Oak Rustic Lacquered Plank (130mm) 36-Y0R-001
£48.95/m2 £40.79/m2 EX VAT
York Oak Rustic Oiled Narrow Plank (90mm) 36-YNO-001
£46.95/m2 £39.13/m2 EX VAT
York Oak Rustic Oiled Plank (130mm) 36-YR0-001
£49.95/m2 £41.63/m2 EX VAT
YO
RK
SOLID
32 SOLID WOOD All prices include VAT
Beautiful mellow colours...
York Oak Select
Brushed Matt
Lacquered Plank
TYPE OF FLOOR Solid Wood
THICKNESS 18mm
LENGTH X WIDTH 300–1500mm x 130mm
average length 700mm
PACK SIZE 2.29m2
TYPE OF FINISH Brushed Matt Lacquered
GRADE Select
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Stick down or secret nail
UNDERFLOOR HEATING Not advised
HARDNESS Hard
DURABILITY High wear resistance
York Oak Select Brushed Matt Lacquered Plank36-YBM-004
£57.95/m2 £.48.29 /m2 EX VAT
YO
RK
SOLID
33SOLID WOODAll prices include VAT
TYPE OF FLOOR Solid Wood
THICKNESS 18mm
LENGTH X WIDTH 300–1500mm x 130mm
average length 700mm
PACK SIZE 2.29m2
TYPE OF FINISH Lacquered
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Stick down or secret nail
UNDERFLOOR HEATING Not advised
HARDNESS Hard
DURABILITY High wear resistance
York Oak Antique
Handscraped
Lacquered Plank
Hand scraped to add character and charm...
York Oak Antique Handscraped Lacquered Plank36-YOA-003
£59.95/m2 £49.96/m2 EX VAT
YO
RK
SOLID
34 SOLID WOOD All prices include VAT
TYPE OF FLOOR Solid Wood
THICKNESS 18mm
LENGTH X WIDTH 300–1500mm x 130mm
average length 700mm
PACK SIZE 2.29m2
TYPE OF FINISH Lacquered
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Stick down or secret nail
UNDERFLOOR HEATING Not advised
HARDNESS Medium
DURABILITY High wear resistance
York Walnut
Rustic Lacquered
Plank
Swirling colours of dark chocolate and honey...
York Walnut Rustic Lacquered Plank36-YWR-001
£93.95/m2 £78.29/m2 EX VAT
YO
RK
SOLID
35SOLID WOODAll prices include VAT
Dunster is an exclusive, premium quality unfi nished oak fl oor.
This enables you to fi nish it to your own choice and colour.
Its rustic character brings together all the richness of colour and
character to be found in this most enduring of materials.
Dunster is a traditional tongue and groove fl oor with an excellent
width and length specifi cation.
Now available in mixed widths.
DUNSTER OAKWOOD FLOORING AT ITS BEST
UNFINISHED SURFACE
TONGUE AND GROOVE JOINT
MANUFACTURED FROM SOLID OAK
STRESS GROOVES
UNFINISHED OAK TRIMS AVAILABLE PRE-FILLED UNFINISHED SURFACE
18-OCU-14018-OCU-16018-OCU-180
DU
NS
TE
RSO
LID
36 SOLID WOOD All prices include VAT
TYPE OF FLOOR Solid Wood
THICKNESS 18mm
LENGTH X WIDTH 500–2000mm x 140/160/180mm
PACK SIZE 1.68 / 1.92 / 2.16
TYPE OF FINISH Unfinished. Filled and Sanded.
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES None
METHOD OF FIXING Stick down or secret nail
UNDERFLOOR HEATING Not advised
HARDNESS Hard
DURABILITY High wear resistance
Dunster Oak
Unfinished Plank
French Oak, the most beautiful timber in both character and colour...
18mm x 160mm x 500–2000mm
18-OCU-160
£69.95/m2 £58.29/m2 EX VAT
18mm x 180mm x 500–2000mm
18-OCU-180
£73.95/m2 £61.63/m2 EX VAT
Supplied Unfinished
After finish coat applied
Dunster Oak Unfinished Plank 18mm x 140mm x 500–2000mm
18-OCU-140
£65.95/m2 £54.96/m2 EX VAT
DU
NS
TE
RSO
LID
37SOLID WOODAll prices include VAT
With this revolutionary new wood fl oor, the issues of how to solve
the diffi culties of damp subfl oors no longer pose a problem*.
Both the top layer and the core are manufactured from Solid Oak.
Having an engineered core gives the product the stability that is
not found in a conventionally produced solid wood fl oor.
You simply fl oat the fl oor on an underlay with a damp proof
membrane, just like any engineered or laminate fl oor.
This fl oor has fi ve coats of high-wear, matt lacquer, which is applied
to a subtly brushed surface giving a beautifully textured fi nish that
is superbly durable and practical for almost all applications.
FLINKCLEVER WITH WOOD
HIGH WEAR RESISTANT UV LACQUER
SOLID OAK ENGINEERED CORE
GLUELESS LOC JOINT
MATCHING TRIMS AVAILABLE
FLOAT OVER AN UNDERLAY WITH DPM
76-ORL-200 76-OWL-20076-ONL-200 76-OCL-200
* Detailed instructions are provided in each pack as to installation procedures and precautions which must be taken.
FLINK
SOLID
38 SOLID WOOD All prices include VAT
Flink Oak Rustic
Natural Brushed
Matt Lacquered
Plank
TYPE OF FLOOR Engineered Solid Oak
THICKNESS 14mm
LENGTH X WIDTH 300–1200mm x 125mm
PACK SIZE 1.50m2
TYPE OF FINISH Brushed Matt Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Not advised
HARDNESS Hard
DURABILITY High wear resistance
Manufactured from European Oak...
Flink Oak Rustic Natural Brushed Matt Lacquered Plank76-ORL-200
£63.95/m2 £53.29/m2 EX VAT
FLINK
SOLID
39SOLID WOODAll prices include VAT
Flink Oak Rustic
Whitened
Brushed Matt
Lacquered Plank
TYPE OF FLOOR Engineered Solid Oak
THICKNESS 14mm
LENGTH X WIDTH 300–1200mm x 125mm
PACK SIZE 1.50m2
TYPE OF FINISH Brushed Matt Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Not advised
HARDNESS Hard
DURABILITY High wear resistance
Beautiful textured surface processed with 5 surface finishes...
Flink Oak Rustic Whitened Brushed Matt Lacquered Plank76-ONL-200
£65.95/m2 £54.96/m2 EX VAT
FLINK
SOLID
40 SOLID WOOD All prices include VAT
TYPE OF FLOOR Engineered Solid Oak
THICKNESS 14mm
LENGTH X WIDTH 300–1200mm x 125mm
PACK SIZE 1.50m2
TYPE OF FINISH Brushed Matt Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Not advised
HARDNESS Hard
DURABILITY High wear resistance
Reaching standards of precision not previously seen...
Flink Dark
Oak Rustic
Brushed Matt
Lacquered Plank
Flink Dark Oak Rustic Brushed Matt Lacquered Plank76-OCL-200
£65.95/m2 £54.96/m2 EX VAT
FLINK
SOLID
41SOLID WOODAll prices include VAT
FLINK
SOLID
All prices include VATSOLID WOOD42
TYPE OF FLOOR Engineered Solid Oak
THICKNESS 14mm
LENGTH X WIDTH 300–1200mm x 125mm
PACK SIZE 1.50m2
TYPE OF FINISH Brushed Matt Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Not advised
HARDNESS Hard
DURABILITY High wear resistance
Stable, practical and easy to fit...
Flink Oak Rustic
Cognac Brushed
Matt Lacquered Plank
Flink Oak Rustic Cognac Brushed Matt Lacquered Plank76-OWL-200
£65.95/m2 £54.96/m2 EX VAT
FLINK
SOLID
43SOLID WOODAll prices include VAT
Parquetry is one of the oldest forms of wood fl ooring and refl ects
the very best in traditional techniques. In recent years there has
been a renaissance in this sophisticated style which has seen it
work equally well in both traditional and contemporary settings.
Machined to exacting standards with a universal tongue and grove
joint, the Denbigh Blocks are available in two lengths allowing them
to be laid in a variety of patterns to complement their surroundings.
Popular designs include herringbone, basket weave and ship’s deck
but the possibilities are endless.
DENBIGH SOLID OAK BLOCKSCLASSICAL, ELEGANT & TIMELESS
MANUFACTURED FROM SOLID OAK
TONGUE AND GROOVE JOINT
UNFINISHED SURFACE
UNFINISHED SURFACE
04-ORU-23004-ORU-280
22mm
DE
NB
IGH
SOLID
44 SOLID WOOD All prices include VAT
Denbigh Solid
Oak Unfinished
Blocks
TYPE OF FLOOR Solid Wood
THICKNESS 22mm
LENGTH X WIDTH 230/280mm x 70mm
PACK SIZE 0.515/0.627m2
TYPE OF FINISH Unfinished. Sanded
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES None
METHOD OF FIXING Stick down
UNDERFLOOR HEATING Not advised
HARDNESS Hard
DURABILITY High wear resistance
Traditional parquet style...
Denbigh Solid Oak Unfinished Blocks 22mm x 70mm x 230mm
04-ORU-230
£46.95/m2 £39.13/m2 EX VAT
22mm x 70mm x 280mm
04-ORU-280
£48.95/m2 £40.79/m2 EX VAT
DE
NB
IGH
SOLID
45SOLID WOODAll prices include VAT
REAL WOOD ENGINEEREDADDED STABILITY WITH GREATER VARIETY OF DESIGN
THE CONCEPT OF REAL WOOD ENGINEERED FLOORS
Solid wood fl ooring has been used for hundreds
of years in houses and public buildings but it is
really only in the last 65 years that the process
has evolved from a craft to a science, with the
introduction of multi-layered products and more
recently in the late 1990’s the development of
integral locking systems that greatly facilitate the
installation of the fl oor.
The increasing popularity of using wood in
modern homes has led to the need for meeting
signifi cant challenges. New housing is almost
always centrally heated often leading to
relatively low atmospheric moisture in the air;
advances have been made in the materials used
for subfl oors; and most recently, the growing
popularity of underfl oor heating; all this has led to
a need for an increasing level of sophistication in
the fl oors themselves.
Thus the development of a fl oor that is
multi-layered in construction and provides:
1. Greater stability.
2. The very best use of a natural resource in the
least wasteful and the most practical way.
3. A product that in some cases can be laid and
re-laid many times making it both economical
and re-usable.
4. A product that can be used safely in
conjunction with underfl oor heating subject
to certain conditions.
5. A product that can be laid much faster
resulting in lower fi tting costs, and,
if pre-fi nished, can be used immediately
after installation.
6. A greater range of design possibilities off ering
single plank, two strip and three strip options.
REAL WOOD ENGINEERED
These fl oors off er added
stability and a greater variety
of design. They are normally
constructed in 3 layers, using
the chosen species as a top
wear layer, with a central
core of either softwood*, high
density fi breboard (HDF) with a
balancing spruce veneer, or birch
plywood. The top wear layer
can vary from 0.6mm to 6mm
depending on the product.
*Expansion and contraction of the softwood
core due to seasonal changes in humidity may
produce a squeaking sound if the subfl oor is
not perfectly fl at. Waxing of the joints can
eliminate this.
ENG
INEERED
46 All prices include VATREAL WOOD ENGINEERED
RA
GLA
N
Available in 3 diff erent species and off ering a total of 10 variations.
This fl oor is coated with fi ve coats of high build UV lacquer or oil
and is supported by a high density fi breboard core.
Each plank is bevelled on all four edges and it has a glueless
“Drop & Lock” jointing system that is easy to install and extremely
practical. Particularly good for use with underfl oor heating.
RAGLAN BEAUTIFUL, PRACTICAL AND DURABLE
5 COATS OF UV LACQUER/OIL
HDF CORE
2.5MM WEAR LAYER
GLUELESS LOC JOINT
GLUELESS LOC SYSTEM
34-ORL-00134-ORO-00134-OBL-001
34-OAO-00134-ORC-001 34-OWO-001 34-MAL-00234-OWS-001 34-OCL-001 34-WAL-002
10.5mm
PERFECT FOR USE WITH UNDERFLOOR HEATING
ENG
INEERED
47All prices include VAT REAL WOOD ENGINEERED
Raglan Oak
Rustic Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 10.5mm (wear layer 2.5mm)
LENGTH X WIDTH 1860mm x 148mm
PACK SIZE 2.20m2
TYPE OF FINISH Lacquered, Brushed Matt
Lacquered or OiledGRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Raglan Oak Rustic Lacquered Plank34-ORL-001
£45.95/m2 £38.29/m2 EX VAT
Raglan Oak Rustic Oiled Plank34-ORO-001
£46.95/m2 £39.13/m2 EX VAT
Raglan Oak Rustic Brushed Matt Lacquered Plank34-OBL-001
£47.95/m2 £39.96/m2 EX VAT
RA
GLA
NEN
GIN
EERED
48 All prices include VATREAL WOOD ENGINEERED
RA
GLA
NEN
GIN
EERED
49All prices include VAT REAL WOOD ENGINEERED
Raglan Oak
Rustic Cognac
Brushed Matt
Lacquered Plank
Raglan Oak Rustic Cognac Brushed Matt Lacquered Plank34-ORC-001
£51.95/m2 £43.29/m2 EX VAT
TYPE OF FLOOR Real Wood Engineered
THICKNESS 10.5mm (wear layer 2.5mm)
LENGTH X WIDTH 1860mm x 148mm
PACK SIZE 2.20m2
TYPE OF FINISH Brushed Matt Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
RA
GLA
NEN
GIN
EERED
50 All prices include VATREAL WOOD ENGINEERED
Raglan Oak
Rustic White
Oiled Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 10.5mm (wear layer 2.5mm)
LENGTH X WIDTH 1860mm x 148mm
PACK SIZE 2.20m2
TYPE OF FINISH Oiled
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Raglan Oak Rustic White Oiled Plank34-OWO-001
£51.95/m2 £43.29/m2 EX VAT
RA
GLA
NEN
GIN
EERED
51All prices include VAT REAL WOOD ENGINEERED
Raglan Oak
Rustic Antique
Oiled Plank
REAL WOOD ENGINEERED
TYPE OF FLOOR Real Wood Engineered
THICKNESS 10.5mm (wear layer 2.5mm)
LENGTH X WIDTH 1860mm x 148mm
PACK SIZE 2.20m2
TYPE OF FINISH Oiled
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Raglan Oak Rustic Antique Oiled Plank34-OAO-001
£51.95/m2 £43.29/m2 EX VAT
RA
GLA
NEN
GIN
EERED
52 All prices include VAT
RA
GLA
NEN
GIN
EERED
53All prices include VAT REAL WOOD ENGINEERED
Raglan Oak
Rustic White
Smoked Brushed
Matt Lacquered
Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 10.5mm (wear layer 2.5mm)
LENGTH X WIDTH 1860mm x 148mm
PACK SIZE 2.20m2
TYPE OF FINISH Brushed Matt Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Raglan Oak Rustic White Smoked Brushed Matt Lacquered Plank 34-OWS-001
£51.95/m2 £43.29/m2 EX VAT
RA
GLA
NEN
GIN
EERED
54 All prices include VATREAL WOOD ENGINEERED
Raglan Oak
Rustic Coffee
Brushed Matt
Lacquered Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 10.5mm (wear layer 2.5mm)
LENGTH X WIDTH 1860mm x 148mm
PACK SIZE 2.20m2
TYPE OF FINISH Brushed Matt Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Raglan Oak Rustic Coffee Brushed Matt Lacquered Plank 34-OCL-001
£51.95/m2 £43.29/m2 EX VAT
RA
GLA
NEN
GIN
EERED
55All prices include VAT REAL WOOD ENGINEERED
Raglan Maple
Matt Lacquered
Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 10.5mm (wear layer 2.5mm)
LENGTH X WIDTH 1200mm x 125mm
PACK SIZE 1.05m2
TYPE OF FINISH Matt Lacquered
GRADE Select
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Not Advised
HARDNESS Hard
DURABILITY High wear resistance
Raglan Maple Matt Lacquered Plank34-MAL-002
£61.95/m2 £51.63/m2 EX VAT
RA
GLA
NEN
GIN
EERED
56 All prices include VATREAL WOOD ENGINEERED
Raglan Walnut
Matt Lacquered
Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 10.5mm (wear layer 2.5mm)
LENGTH X WIDTH 1200mm x 125mm
PACK SIZE 1.05m2
TYPE OF FINISH Matt Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Medium
DURABILITY High wear resistance
Raglan Walnut Matt Lacquered Plank34-WAL-002
£79.95/m2 £66.63/m2 EX VAT
RA
GLA
NEN
GIN
EERED
57All prices include VAT REAL WOOD ENGINEERED
Harlech is an engineered fl oor which is compatible with underfl oor
heating. It is available in a number of fi nishes with a softwood
core and a hardwood wear layer of either Oak or American
Black Walnut.
It is fi nished using either 5 coats of UV lacquer or a UV cured
Oil which gives the product a beautiful lustre and is available
both in Natural or Stained fi nishes to blend in with most decors.
Tremendous value for money.
HARLECHELEGANCE AND PRACTICALITY COMBINED
4MM WEAR LAYER
5 COATS OF UV LACQUER/OIL
ENGINEERED SOFTWOOD CORE
TONGUE AND GROVE JOINT
35-HOE-300 35-HOL-00135-HOO-005
35-HOC-14835-HOB-001
35-HRO-001 35-HWS-001 35-HOC-001
MATCHINGTRIMS AVAILABLE MAINTENANCE PRODUCTS AVAILABLE P.26
35-HWL-00135-HWO-148 35-HAN-148
15mmN.B: Symbols exclude Harlech Eco Oak Rustic Lacquered 3 Strip.
HA
RLE
CH
ENG
INEERED
58 All prices include VATREAL WOOD ENGINEERED
Harlech Eco Oak
Rustic Lacquered
3 Strip
TYPE OF FLOOR Real Wood Engineered
THICKNESS 10.5mm (wear layer 2.5mm)
LENGTH X WIDTH 1090mm x 182mm
PACK SIZE 1.587m2
TYPE OF FINISH Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Harlech Eco Oak Rustic Lacquered 3 Strip35-HOE-300
£31.95/m2 £26.63/m2 EX VAT
HA
RLE
CH
ENG
INEERED
59All prices include VAT REAL WOOD ENGINEERED
Harlech Oak
Rustic Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 15mm (wear layer 4mm)
LENGTH X WIDTH 1860mm x 148mm
can be one cut length per pack
PACK SIZE 1.65m2
TYPE OF FINISH UV Oiled or Brushed
Matt LacqueredGRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Harlech Oak Rustic Brushed Matt Lacquered Plank35-HOB-001
£52.95/m2 £44.13/m2 EX VAT
Harlech Oak Rustic Oiled Plank35-HOC-148
£49.95/m2 £41.63/m2 EX VAT
HA
RLE
CH
ENG
INEERED
60 All prices include VATREAL WOOD ENGINEERED
HA
RLE
CH
ENG
INEERED
61All prices include VAT REAL WOOD ENGINEERED
Harlech Oak Extra Rustic Oiled Wide Plank35-HRO-001
£51.95/m2 £43.29/m2 EX VAT
Harlech Oak
Extra Rustic
Oiled Wide PlankTYPE OF FLOOR Real Wood Engineered
THICKNESS 15mm (wear layer 4mm)
LENGTH X WIDTH 1860mm x 189mm
can be one cut length per pack
PACK SIZE 2.10m2
TYPE OF FINISH UV Oiled
GRADE Extra Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Bringing nature right into your room...
HA
RLE
CH
ENG
INEERED
62 All prices include VATREAL WOOD ENGINEERED
HA
RLE
CH
ENG
INEERED
63All prices include VAT REAL WOOD ENGINEERED
Harlech Oak
Select Wide
Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 15mm (wear layer 4mm)
LENGTH X WIDTH 1860mm x 189mm
can be one cut length per pack
PACK SIZE 2.10m2
TYPE OF FINISH UV Lacquered or UV Oiled
GRADE Select
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Harlech Oak Select Lacquered Wide Plank35-HOL-001
£61.95/m2 £51.63/m2 EX VAT
Harlech Oak Select Oiled Wide Plank35-HOO-005
£61.95/m2 £51.63/m2 EX VAT
Traditional tongue and groove on 4 edges for maximum stability...
HA
RLE
CH
ENG
INEERED
64 All prices include VATREAL WOOD ENGINEERED
Harlech Oak
White Smoked
Brushed Matt
Lacquered Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 15mm (wear layer 4mm)
LENGTH X WIDTH 1860mm x 148mm
can be one cut length per pack
PACK SIZE 1.65m2
TYPE OF FINISH Brushed Matt Lacquered
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Sophisticated, elegant with the allure of the unexpected...
Harlech Oak White Smoked Brushed Matt Lacquered Plank 35-HWS-001
£63.95/m2 £53.29/m2 EX VAT
HA
RLE
CH
ENG
INEERED
65All prices include VAT REAL WOOD ENGINEERED
Harlech Oak
Cognac Brushed
Matt Lacquered
Plank
Harlech Oak Cognac Brushed Matt Lacquered Plank35-HOC-001
£59.95/m2 £49.96/m2 EX VAT
TYPE OF FLOOR Real Wood Engineered
THICKNESS 15mm (wear layer 4mm)
LENGTH X WIDTH 1860mm x 148mm
can be one cut length per pack
PACK SIZE 1.65m2
TYPE OF FINISH Brushed Matt Lacquered
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Harlech captures the full tradition of wood flooring...
HA
RLE
CH
ENG
INEERED
66 All prices include VATREAL WOOD ENGINEERED
Harlech Oak
Rustic White
Oiled Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 15mm (wear layer 4mm)
LENGTH X WIDTH 1860mm x 148mm
can be one cut length per pack
PACK SIZE 1.65m2
TYPE OF FINISH UV Oiled
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
5 coats of the chosen finish give maximum wear...
Harlech Oak Rustic White Oiled Plank35-HWO-148
£58.95/m2 £49.13/m2 EX VAT
HA
RLE
CH
ENG
INEERED
67All prices include VAT REAL WOOD ENGINEERED
Harlech Oak
Rustic Antique
Oiled Plank
Harlech Oak Rustic Antique Oiled Plank35-HAN-148
£61.95/m2 £51.63/m2 EX VAT
TYPE OF FLOOR Real Wood Engineered
THICKNESS 15mm (wear layer 4mm)
LENGTH X WIDTH 1860mm x 148mm
can be one cut length per pack
PACK SIZE 1.65m2
TYPE OF FINISH UV Oiled
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
With its long lengths and bevelled edges...
HA
RLE
CH
ENG
INEERED
68 All prices include VATREAL WOOD ENGINEERED
Harlech Walnut
Lacquered Plank
Harlech Walnut Lacquered Plank35-HWL-001
£95.95/m2 £79.96/m2 EX VAT
Combining choice with beauty and practicality...
TYPE OF FLOOR Real Wood Engineered
THICKNESS 15mm (wear layer 4mm)
LENGTH X WIDTH 1860mm x 148mm
can be one cut length per pack
PACK SIZE 1.65m2
TYPE OF FINISH Lacquered
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Medium
DURABILITY High wear resistance
HA
RLE
CH
ENG
INEERED
69All prices include VAT REAL WOOD ENGINEERED
Harlech Magnum is the grandfather of the Harlech range!
With its 21mm overall thickness and 6mm wear layer on a ply core,
Magnum off ers exceptional qualities of practical, hardwearing
durability at a very reasonable cost.
HARLECH MAGNUMSUPERIOR THICKNESS SPECIFICATION
6MM WEAR LAYER
5 COATS OF UV LACQUER/OIL
ENGINEERED PLYWOOD CORE
TONGUE AND GROVE JOINT
MATCHINGTRIMS AVAILABLE TRADITIONAL BEVELLED EDGES
35-HMB-148 35-HML-00135-HBO-00135-HMU-001
21mm
HA
RLE
CH
MA
GN
UM
ENG
INEERED
70 All prices include VATREAL WOOD ENGINEERED
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
TYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1860mm x 148mm
PACK SIZE 1.65m2
one cut length per pack
TYPE OF FINISH Brushed and Oiled
GRADE Rustic
Harlech Magnum
Rustic Oak
Narrow Plank
Harlech Magnum 21mm thickness
Wear Layer 6mm Rustic Oak Brushed
& Oiled21mm x 148mm
35-HMB-148
£63.95/m2 £53.29/m2 EX VAT
HA
RLE
CH
MA
GN
UM
ENG
INEERED
71All prices include VAT REAL WOOD ENGINEERED
Harlech Magnum
Rustic Oak Wide
PlankTYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1860mm x 189mm
PACK SIZE 2.11m2
one cut length per pack
TYPE OF FINISH Unfinished, Lacquered
or Brushed & OiledGRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Rustic Oak Lacquered 21mm x 189mm
35-HML-001
£67.95/m2 £56.63/m2 EX VAT
Rustic Oak Brushed & Oiled 21mm x 189mm
35-HBO-001
£69.95/m2 £58.29/m2 EX VAT
Rustic Oak Unfinished 21mm x 189mm
35-HMU-001
£61.95/m2 £51.63/m2 EX VAT
HA
RLE
CH
MA
GN
UM
ENG
INEERED
72 All prices include VATREAL WOOD ENGINEERED
HA
RLE
CH
MA
GN
UM
ENG
INEERED
73All prices include VAT REAL WOOD ENGINEERED
Windsor has a pedigree for quality and reliability. This is a top
quality engineered fl oor utilising a patented loc system enabling
it to be laid and taken up again with ease.
It can be used both in domestic and commercial environments
with confi dence being fi nished with 6 coats of one of the hardest
wearing lacquers available.
WINDSORA BEAUTIFUL AND FUNCTIONAL FLOOR
4MM WEAR LAYER
6 COATS OF UV LACQUER/OIL
GLUELESS LOC JOINT
ENGINEEERED SOFTWOOD CORE
FLOAT OVER AN UNDERLAY
46-WOU-003 46-WOL-00146-WOO-001
46-WOB-001
GLUELESS LOC SYSTEM
46-WMC-00346-WWO-001 46-WME-00346-WDO-001
WIN
DS
OR
ENG
INEERED
74 All prices include VATREAL WOOD ENGINEERED
Windsor
Oak Unique
Lacquered 3 Strip
TYPE OF FLOOR Real Wood Engineered
THICKNESS 14mm (wear layer 4mm)
LENGTH X WIDTH 2190mm x 182mm
PACK SIZE 3.587m2
TYPE OF FINISH Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Renowned for its superior appearance and high specification...
Windsor Oak Unique Lacquered 3 Strip 46-WOU-003
£38.95/m2 £32.46/m2 EX VAT
WIN
DS
OR
ENG
INEERED
75All prices include VAT REAL WOOD ENGINEERED
Windsor Oak
Rustic Plank
A premium quality floor...
TYPE OF FLOOR Real Wood Engineered
THICKNESS 14mm (wear layer 4mm)
LENGTH X WIDTH 2200mm x 182mm
one cut length per pack
PACK SIZE 3.203m2
TYPE OF FINISH UV Lacquered or UV Oiled
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Windsor Oak Rustic Lacquered Plank 46-WOL-001
£66.95/m2 £55.79/m2 EX VAT
Windsor Oak Rustic UV Oiled Plank46-WOO-001
£70.95/m2 £59.13/m2 EX VAT
WIN
DS
OR
ENG
INEERED
76 All prices include VATREAL WOOD ENGINEERED
Modern, cool and clean...
Windsor Oak
Rustic Oiled
Plank With Bevels
TYPE OF FLOOR Real Wood Engineered
THICKNESS 14mm (wear layer 4mm)
LENGTH X WIDTH 2200mm x 182mm
one cut length per pack
PACK SIZE 3.203m2
TYPE OF FINISH UV Oiled
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES 2 long edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Windsor Oak Rustic Oiled Plank With Bevels46-WOB-001
£75.95/m2 £63.29/m2 EX VAT
WIN
DS
OR
ENG
INEERED
77All prices include VAT REAL WOOD ENGINEERED
Windsor Oak
Rustic Dark
Oiled Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 14mm (wear layer 4mm)
LENGTH X WIDTH 2200mm x 182mm
one cut length per pack
PACK SIZE 3.203m2
TYPE OF FINISH UV Oiled
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
A warm blend of the traditional and the contemporary...
Windsor Oak Rustic Dark Oiled Plank46-WDO-001
£75.95/m2 £63.29/m2 EX VAT
WIN
DS
OR
ENG
INEERED
78 All prices include VATREAL WOOD ENGINEERED
Windsor Oak
Rustic White
Oiled Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 14mm (wear layer 4mm)
LENGTH X WIDTH 2200mm x 182mm
one cut length per pack
PACK SIZE 3.203m2
TYPE OF FINISH UV Oiled
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Whitened for sophistication and a contemporary feel...
Windsor Oak Rustic White Oiled Plank46-WWO-001
£75.95/m2 £63.29/m2 EX VAT
WIN
DS
OR
ENG
INEERED
79All prices include VAT REAL WOOD ENGINEERED
TYPE OF FLOOR Real Wood Engineered
THICKNESS 14mm (wear layer 4mm)
LENGTH X WIDTH 2200mm x 182mm
one cut length per pack
PACK SIZE 3.203m2
TYPE OF FINISH Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Very Hard
DURABILITY High wear resistance
Warm, hard-wearing and practical for any situation...
Windsor Merbau
Lacquered 3 Strip
Windsor Merbau Lacquered 3 Strip46-WME-003
£59.95/m2 £49.96/m2 EX VAT
WIN
DS
OR
ENG
INEERED
80 All prices include VATREAL WOOD ENGINEERED
TYPE OF FLOOR Real Wood Engineered
THICKNESS 14mm (wear layer 4mm)
LENGTH X WIDTH 2200mm x 182mm
one cut length per pack
PACK SIZE 3.203m2
TYPE OF FINISH Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Not Advised
HARDNESS Hard
DURABILITY High wear resistance
A warm blend of the traditional and the contemporary...
Windsor
European Maple
Classic Lacquered
3 Strip
Windsor European Maple Classic Lacquered 3 Strip46-WMC-003
£59.95/m2 £49.96/m2 EX VAT
WIN
DS
OR
ENG
INEERED
81All prices include VAT REAL WOOD ENGINEERED
A stunning range of 21mm thick engineered boards with a 6mm
wear layer of solid oak on a Birch ply backing.
Chepstow has the same wear layer as a solid wood fl oor – you can
sand and re-sand many times but with all the stability benefi ts of an
engineered board.
CHEPSTOW OAK RUSTICENGINEERED STABILITY, SOLID APPEARANCE
6MM WEAR LAYER
5 COATS OF HARDWAX OIL
PLYWOOD CORE
TONGUE AND GROOVE JOINT
MATCHINGTRIMS AVAILABLE BEVELLED EDGES
21mm
65-PON-001 65-POA-00165-POW-001 65-POG-001 65-AOC-001 65-AWS-001 65-AON-001 65-AOS-001
CH
EP
ST
OW
ENG
INEERED
82 All prices include VATREAL WOOD ENGINEERED
Chepstow Oak
Rustic Natural
Planed Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1860mm x 189mm
one cut length per pack
PACK SIZE 2.11m2
TYPE OF FINISH Hardwax Oil
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Premium quality, 21mm thickness, long wide boards, the same wear layer as a solid wood floor with greater stability...
Chepstow Oak Rustic Natural Planed Plank65-PON-001
£81.95/m2 £68.29/m2 EX VAT
CH
EP
ST
OW
ENG
INEERED
83All prices include VAT REAL WOOD ENGINEERED
Chepstow Oak
Rustic Whitened
Planed Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1860mm x 189mm
one cut length per pack
PACK SIZE 2.11m2
TYPE OF FINISH Hardwax Oil
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
A light white stain with this rustic floor makes it characterful and yet contemporary...
Chepstow Oak Rustic Whitened Planed Plank65-POW-001
£81.95/m2 £68.29/m2 EX VAT
CH
EP
ST
OW
ENG
INEERED
84 All prices include VATREAL WOOD ENGINEERED
Chepstow Oak
Rustic Grey
Planed Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1860mm x 189mm
one cut length per pack
PACK SIZE 2.11m2
TYPE OF FINISH Hardwax Oil
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
The light grey stain takes tradition and blends it skillfully with modern...
Chepstow Oak Rustic Grey Planed Plank65-POG-001
£81.95/m2 £68.29/m2 EX VAT
CH
EP
ST
OW
ENG
INEERED
85All prices include VAT REAL WOOD ENGINEERED
Chepstow Oak
Rustic Antique
Planed PlankTYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1860mm x 189mm
one cut length per pack
PACK SIZE 2.11m2
TYPE OF FINISH Hardwax Oil
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
The dark stain highlights the beauty of the grain pattern...
Chepstow Oak Rustic Antique Planed Plank65-POA-001
£81.95/m2 £68.29/m2 EX VAT
CH
EP
ST
OW
ENG
INEERED
86 All prices include VATREAL WOOD ENGINEERED
CH
EP
ST
OW
ENG
INEERED
87All prices include VAT REAL WOOD ENGINEERED
Chepstow
Charcoal Aged
& Distressed
Oak Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1900mm x 190mm
one cut length per pack
PACK SIZE 1.444m2
TYPE OF FINISH Hardwax Oil
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
These floors are smoked to age the timber.Stains and waxes are then lovingly applied by hand...
Due to the techniques used
for distressing there can be
some roughness on the surface
of the floor
Chepstow Charcoal Aged & Distressed Oak Plank65-AOC-001
£103.95/m2 £86.63/m2 EX VAT
CH
EP
ST
OW
ENG
INEERED
88 All prices include VATREAL WOOD ENGINEERED
Chepstow White
Smoked Aged
& Distressed
Oak Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1900mm x 190mm
one cut length per pack
PACK SIZE 1.444m2
TYPE OF FINISH Hardwax Oil
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Double smoked to give a light grey stone washed effect,combined with the ageing...
Due to the techniques used
for distressing there can be
some roughness on the surface
of the floor
Chepstow White SmokedAged & DistressedOak Plank65-AWS-001
£103.95/m2 £86.63/m2 EX VAT
CH
EP
ST
OW
ENG
INEERED
89All prices include VAT REAL WOOD ENGINEERED
Chepstow
Natural Aged
& Distressed
Oak Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1900mm x 190mm
one cut length per pack
PACK SIZE 1.444m2
TYPE OF FINISH Hardwax Oil
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Carefully worked edges to reflect the wear of many feet, bruises that mark the passage of time. Beautiful floors for the discerning!
Due to the techniques used
for distressing there can be
some roughness on the surface
of the floor
Chepstow Natural Aged & Distressed Oak Plank65-AON-001
£103.95/m2 £86.63/m2 EX VAT
CH
EP
ST
OW
ENG
INEERED
90 All prices include VATREAL WOOD ENGINEERED
Chepstow
Sienna Aged
& Distressed
Oak Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1900mm x 190mm
one cut length per pack
PACK SIZE 1.444m2
TYPE OF FINISH Hardwax Oil
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Exuding a lovely blend of honeyed tones...Due to the techniques used
for distressing there can be
some roughness on the surface
of the floor
Chepstow Sienna Aged & Distressed Oak Plank65-AOS-001
£103.95/m2 £86.63/m2 EX VAT
CH
EP
ST
OW
ENG
INEERED
91All prices include VAT REAL WOOD ENGINEERED
DESIGNER COLLECTIONA LITTLE BIT OF BEAUTY THAT NO ONE HAS EVER SEEN BEFORE
Every Woodpecker® fl oor is truly unique – the fact
that no two trees are ever entirely the same is a
large part of the attraction. But there are some
people who want something that’s dramatically
diff erent, and very much out of the ordinary.
Value for money is still a consideration for these
discerning individuals, but it’s not as important
to them as outstanding quality, exclusivity
and originality.
With this in mind we’ve scoured the world to
discover remarkable fl oors that have been created
from both traditional and exotic tree species.
The result, we think you’ll agree, is a stunning
collection that’s sure to give the most creative and
imaginative designers a wealth of inspiration.
Having said this, these fl oors not only look good,
they also meet the most stringent practical criteria.
Because these fl oors are so unusual we don’t hold
them in stock, however, if you are looking for a
fl oor that’s sure to impress, they are more than
worth the wait.
When ordering from this collection a 30% deposit
will be required.
Please allow 4–8 weeks for delivery from the date
of your confi rmed order.
DESIG
NER
92 All prices include VATDESIGNER COLLECTION
The development of a herringbone engineered fl oor with a glueless
locking joint means that you can now enjoy a timeless style and
design at the fraction of the cost of the solid wood equivalent.
This fl oor is fl oated and can be fi tted by any competent installer
very quickly at a fraction of the cost previously required!
The fl oor is treated with a specially developed, hard wearing
lacquered fi nish containing nanoparticles, which increases
resistance to minor scratches and keeps the fl oor looking new
for longer. This fi nish looks like an oiled fl oor, but enjoys all the
low maintenance benefi ts of a lacquered fl oor.
GOODRICHENGINEERED HERRINGBONE DESIGN LOC JOINT
HIGH WEAR RESISTANT LACQUER
HDF CORE
0.6MM WEAR LAYER
GLUELESS LOC JOINT
32-GOH-001
GLUELESS LOC SYSTEMPERFECT FOR USE WITH UNDERFLOOR HEATING
7.2mm
GO
OD
RIC
HD
ESIGN
ER
93All prices include VAT DESIGNER COLLECTION
Goodrich Oak
Herringbone
LacqueredTYPE OF FLOOR Real Wood Engineered
THICKNESS 7.2mm (wear layer 0.6mm)
LENGTH X WIDTH 385mm x 77mm
PACK SIZE 1.08 m2
TYPE OF FINISH Lacquered
GRADE Select
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Goodrich Oak Herringbone Lacquered32-GOH-001
£77.95/m2 £64.96/m2 EX VAT
GO
OD
RIC
HD
ESIGN
ER
94 All prices include VATDESIGNER COLLECTION
GO
OD
RIC
HD
ESIGN
ER
95All prices include VAT DESIGNER COLLECTION
The Chepstow Designer range off ers you a fl oor that is just a bit
more than “another fl oor” this range keeps you right in touch
with nature with the fl oors still showing the kerf of the saw marks
and that delightfully rustic feel that conjures up the smell of fresh
sawdust and the pleasure of seeing freshly sawn timber.
The 6mm wear layer of solid Oak on a ply backing gives you the
feel of solid wood with all the stability benefi ts of engineered.
CHEPSTOW DESIGNERKEEPING CLOSE TO NATURE
6MM WEAR LAYER
PLYWOOD CORE
TONGUE AND GROOVE JOINT
65-SON-001
21mm
65-SOG-001 65-SOB-001
BEVELLED EDGES MAINTENANCE PRODUCTS AVAILABLE P.26
CH
EP
ST
OW
DESIG
NER
96 All prices include VATDESIGNER COLLECTION
Chepstow Sawn
“Natural” Oak
Plank
Straight from the saw!
TYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1860mm x 189mm
one cut length per pack
PACK SIZE 2.11m2
TYPE OF FINISH Hardwax Oil
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Due to the techniques used
for distressing there can be
some roughness on the surface
of the floor
Chepstow Sawn “Natural” Oak Plank65-SON-001
£109.95/m2 £91.63/m2 EX VAT
CH
EP
ST
OW
DESIG
NER
97All prices include VAT DESIGNER COLLECTION
TYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1860mm x 189mm
one cut length per pack
PACK SIZE 2.11m2
TYPE OF FINISH Hardwax Oil
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Straight from the saw!
Chepstow Sawn
“Grey” Oak Plank
Due to the techniques used
for distressing there can be
some roughness on the surface
of the floor
Chepstow Sawn “Grey” Oak Plank65-SOG-001
£109.95/m2 £91.63/m2 EX VAT
CH
EP
ST
OW
DESIG
NER
98 All prices include VATDESIGNER COLLECTION
Chepstow Sawn
“Bronzed” Oak
Plank
TYPE OF FLOOR Real Wood Engineered
THICKNESS 21mm (wear layer 6mm)
LENGTH X WIDTH 1860mm x 189mm
one cut length per pack
PACK SIZE 2.11m2
TYPE OF FINISH Hardwax oil
GRADE Rustic
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated, nailed or stuck down
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Due to the techniques used
for distressing there can be
some roughness on the surface
of the floor
Chepstow Sawn “Bronzed” Oak Plank65-SOB-001
£109.95/m2 £91.63/m2 EX VAT
CH
EP
ST
OW
DESIG
NER
99All prices include VAT DESIGNER COLLECTION
Arundel is a range of exclusive premium grade fl oor off ering artistry,
precision, and character. Using the highest quality material in both
native and exotic species, this is a fl oor for the discerning and
adventurous where quality and aesthetic values are of all
importance.
This engineered fl oor is manufactured using a chosen 4mm wear
layer on a high grade softwood core with a spruce backing. It off ers
maximum stability and is easily installed due to its glueless locking
system. With the exception of Jatoba, it is compatible with
underfl oor heating.
ARUNDEL EXCLUSIVE – ELEGANT – EXOTIC
4MM WEAR LAYER
GLUELESS LOC JOINT
SOFTWOOD CORE
FLOAT OVER AN UNDERLAY
68-AWL-00168-AWO-001
68-AJA-001 68-OAW-001
GLUELESS LOC SYSTEM
46-WMC-003
65-AOW-00168-ABA-001
AR
UN
DE
LD
ESIGN
ER
All prices include VATDESIGNER COLLECTION100
TYPE OF FLOOR Real Wood Engineered
THICKNESS 14mm (wear layer 4mm)
LENGTH X WIDTH 2200mm x 182mm
PACK SIZE 3.203m2
TYPE OF FINISH UV Lacquered or UV Oiled
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
Arundel
Walnut Plank
Arundel Walnut Oiled Plank68-AWO-001
£171.95/m2 £143.29/m2 EX VAT
Arundel Walnut Lacquered Plank68-AWL-001
£171.95/m2 £143.29/m2 EX VAT
AR
UN
DE
LD
ESIGN
ER
101SOLID WOODAll prices include VAT 101DESIGNER COLLECTIONAll prices include VAT
Arundel
Jatoba Plank
Arundel Jatoba Lacquered Plank 68-AJA-001
£131.95/m2 £109.96/m2 EX VAT
TYPE OF FLOOR Real Wood Engineered
THICKNESS 14mm (wear layer 4mm)
LENGTH X WIDTH 2200mm x 182mm
PACK SIZE 3.203m2
TYPE OF FINISH Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Not advisedA
RU
ND
EL
DESIG
NER
102 SOLID WOOD All prices include VAT102 All prices include VATDESIGNER COLLECTION
TYPE OF FLOOR Real Wood Engineered
THICKNESS 14mm (wear layer 4mm)
LENGTH X WIDTH 2200mm x 182mm
PACK SIZE 3.203m2
TYPE OF FINISH Lacquered
GRADE Rustic
TYPE OF JOINT Glueless Loc
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
Arundel Black Ash Plank68-ABA-001
£121.95/m2 £101.63/m2 EX VAT
Arundel Oak Antique
Washed Plank
Arundel Black
Ash Plank
Arundel Oak
Washed Plank
Arundel Oak Antique Washed Plank68-OAW-001
£89.95/m2 £74.96/m2 EX VAT
Arundel Oak Washed Plank68-AOW-001
£89.95/m2 £74.96/m2 EX VAT
Arundel
Collection
AR
UN
DE
LD
ESIGN
ER
103SOLID WOODAll prices include VAT 103All prices include VAT DESIGNER COLLECTION
BAMBOOA TOUCH OF THE EXOTIC ALL THE WAY FROM THE ORIENT
Bamboo is actually a grass, not a wood.
It is tremendously strong and versatile.
In the Far East it is used for everything from
bridges to scaff olding and boats to name but
a few. It is now available as a very attractive
fl oor material in two diff erent styles.
Natural and Coff ee colouration in both vertical
and horizontal laminations.
BAM
BOO
104 All prices include VATBAMBOO
WA
RW
ICK
Engineered Bamboo fl ooring is manufactured from cut strips of
bamboo that are laminated together either vertically or horizontally
to make fl oor boards.
The boards are then machined around all four edges with a tongue
and groove joint.
These boards are available in either Natural or Coff ee which is a
carbonisation process making a beautiful, practical and hardwearing
fl oor covering which can be either stuck or nailed down.
WARWICKHORIZONTAL AND VERTICAL LAMINATIONS
5 COATS OF UV LACQUER
TONGUE AND GROOVE JOINT
LAMINATED BAMBOO STRIPS, VERTICAL OR HORIZONTAL
15mm
MATCHING TRIMS AVAILABLE ROBUST TONGUE & GROOVE JOINT
26-CVM-004 26-NHM-004
BAM
BOO
105All prices include VAT BAMBOO
Warwick Bamboo
Coffee Matt
Lacquered
Vertical
Warwick Bamboo Coffee Matt Lacquered Vertical26-CVM-004
£44.95/m2 £37.46/m2 EX VAT
TYPE OF FLOOR Engineered
THICKNESS 15mm
LENGTH X WIDTH 950mm x 95mm
PACK SIZE 2.166m2
TYPE OF FINISH Matt Lacquered
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Stick down or secret nail
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Shown with Natural Inserts
WA
RW
ICK
BAM
BOO
106 All prices include VATBAMBOO
Warwick Bamboo Natural Matt Lacquered Horizontal26-NHM-004
£44.95/m2 £37.46/m2 EX VAT
TYPE OF FLOOR Engineered
THICKNESS 15mm
LENGTH X WIDTH 950mm x 95mm
PACK SIZE 2.166m2
TYPE OF FINISH Matt Lacquered
TYPE OF JOINT Tongue and Groove
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Stick down or secret nail
UNDERFLOOR HEATING Suitable if fully stuck down
HARDNESS Hard
DURABILITY High wear resistance
Warwick Bamboo
Natural Matt
Lacquered
Horizontal
WA
RW
ICK
BAM
BOO
107All prices include VAT BAMBOO
Strand woven bamboo fl ooring is a natural product derived directly
from the Culm (stem) of the plant, which grows wild in the
mountainous regions of China.
Bamboo is an environmentally friendly, rapidly renewable resource.
It is self regenerating and grows to full maturity within 5 years.
• Environmentally sustainable – natural regeneration of the plant
every 5 years
• Hypoallergenic and non pollutant – no CFCs or VOC emissions
• Easy to install – Uniclic locking system
• Easy to maintain – Damp mop or vacuum as required;
• Available in 4 beautiful colours – Natural, Coff ee, Saddle and White.
STYLE BAMBOOSTYLISH YET SUSTAINABLE STRAND WOVEN BAMBOO
5 COATS OF UV LACQUER
GLUELESS CLIC SYSTEM
STRAND WOVEN BAMBOO
12mm
GLUELESS CLIC SYSTEM MATCHING TRIMS AVAILABLE
20-SWN-001 20-SWC-001 20-SSA-001 20-SWH-001
ST
YLE
BAM
BOO
108 All prices include VATBAMBOO
Style Strand
Woven Bamboo
Natural Lacquered
Plank
TYPE OF FLOOR Strand Woven
THICKNESS 12mm
LENGTH X WIDTH 1850mm x 138mm
PACK SIZE 1.532m2
TYPE OF FINISH Lacquered
TYPE OF JOINT Glueless Clic system
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Very hard
DURABILITY High wear resistance
Style Strand Woven Bamboo Natural Lacquered Plank20-SWN-001
£59.95/m2 £49.96/m2 EX VAT
Shredded, cleaned and compressed under phenomenal pressure,each plank has the tensile strength of steel!
ST
YLE
BAM
BOO
109All prices include VAT BAMBOO
Style Strand Woven
Bamboo Coffee
Lacquered PlankTYPE OF FLOOR Strand Woven
THICKNESS 12mm
LENGTH X WIDTH 1850mm x 138mm
PACK SIZE 1.532m2
TYPE OF FINISH Lacquered
TYPE OF JOINT Glueless Clic system
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Very hard
DURABILITY High wear resistance
Style Strand Woven Bamboo Coffee Lacquered Plank20-SWC-001
£59.95/m2 £49.96/m2 EX VAT
The strongest, most environmentally friendly floor you’ll ever find!
ST
YLE
BAM
BOO
110 All prices include VATBAMBOO
ST
YLE
BAM
BOO
111All prices include VAT BAMBOO
Style Strand
Woven Bamboo
Saddle Lacquered
Plank
TYPE OF FLOOR Strand Woven
THICKNESS 12mm
LENGTH X WIDTH 1850mm x 138mm
PACK SIZE 1.532m2
TYPE OF FINISH Lacquered
TYPE OF JOINT Glueless Clic system
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Very hard
DURABILITY High wear resistance
Style Strand Woven Bamboo Saddle Lacquered Plank20-SSA-001
£63.95/m2 £53.29/m2 EX VAT
Bamboo is a grass, it regenerates every five years ready for harvesting...
ST
YLE
BAM
BOO
112 All prices include VATBAMBOO
Style Strand
Woven Bamboo
Whitened
Lacquered Plank
TYPE OF FLOOR Strand Woven
THICKNESS 12mm
LENGTH X WIDTH 1850mm x 138mm
PACK SIZE 1.532m2
TYPE OF FINISH Lacquered
TYPE OF JOINT Glueless Clic system
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Very hard
DURABILITY High wear resistance
Style Strand Woven Bamboo Whitened Lacquered Plank20-SWH-001
£63.95/m2 £53.29/m2 EX VAT
Helps to remove carbon from the atmosphere as it grows...
ST
YLE
BAM
BOO
113All prices include VAT BAMBOO
The Woodpecker Estilo range of Cork fl oors is
a breakthrough in both innovative design and
ecological sustainability.
ESTILO CORK FLOATING FLOORS HAVE THREE MAIN COMPONENTS
• Top Cork layer: 3mm
• High Density Fibreboard (HDF) core
• Backing: 2mm which acts as a built in sound
absorbing underlay
EASY TO LAY
The Uniclic glueless locking system means the fl oor
can be laid very quickly, can be used immediately
after installation and can if necessary be removed
and reinstalled many times making it a lifetime’s
investment.
THE CHOICE
Available in 8 stunning colours in a unique
tile sized board.
CORKTHE ECOLOGICAL CHOICE
CORK
Estilo Cork fl oors have a choice of beautiful
top layers, with a HDF core and a cork backing
underlay. This off ers an incredibly comfortable,
sound resistant fl oor which is easy to install due
to the glueless locking system.
N.B: Cork is a natural product and is subject to
fading if exposed directly to UV light.
UNIQUE SOUND AND INSULATION PROPERTIES
Cork is a highly eff ective acoustic fl ooring solution
consisting of thousands of tiny air cells. This absorbs
sound reducing impact sound by up to 18 decibels.
Estilo Cork is ideal for use in domestic and
commercial installations.
UNDERFLOOR HEATING
Estilo Cork is suitable for use over both hot water and
radiant underfl oor heating systems. Please refer to
page 25.
CORK
114 All prices include VATCORK
ES
TILO
Cork is an exceptionally comfortable floor to walk on being both warm
and soft adding a sense of luxury to your home.
It is anti-microbial. It can easily be cleaned by vacuuming and damp
mopping with approved cleaners. It is highly fire retardant.
Estilo Cork carries a phenomenal wear rating of 12,000 revolutions
using the Taber test method. Where a wheel is rotated in sand on
the finished surface and measures the number of revolutions before
wearing through the surface. Three times as resilient as a typical
wood floor.
ESTILO CORKRE-INVENTING CORK FLOORING
HIGH WEAR RESISTANT UV LACQUER
CORK WEAR SURFACE
HDF CORE
INTEGERAL UNDERLAY
GLUELESS CLIC JOINT
11mm
COMPLEMENTARY TRIMS AVAILABLE
24-EMA-004 24-EVE-004 24-EPR-004 24-EHE-004 24-EBA-444 24-EMI-444 24-EMC-004 24-ELI-004
IDEAL FOR USE WITH UNDERFLOOR HEATING
CORK
115All prices include VAT CORK
Estilo Madrid
Cork Lacquered
Tile
Each layer of the top surface of every tile is painstakingly applied by hand...
TYPE OF FLOOR Engineered Cork
THICKNESS 11mm (wear layer 3mm)
LENGTH X WIDTH 612mm x 440mm
PACK SIZE 1.62m2
TYPE OF FINISH High Build UV Lacquered
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
DURABILITY Very high wear resistance
Estilo Madrid Cork Lacquered Tile24-EMA-004
£63.95/m2 £53.29/m2 EX VAT
ES
TILO
CORK
116 All prices include VATCORK
Estilo Verona
Cork Lacquered
Tile
TYPE OF FLOOR Engineered Cork
THICKNESS 11mm (wear layer 3mm)
LENGTH X WIDTH 612mm x 440mm
PACK SIZE 1.62m2
TYPE OF FINISH High Build UV Lacquered
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
DURABILITY Very high wear resistance
No two tiles are the same – each floor becomes unique...
Estilo Verona Cork Lacquered Tile24-EVE-004
£55.95/m2 £46.63/m2 EX VAT
ES
TILO
CORK
117All prices include VAT CORK
Warm bourbon hues
Estilo Prague
Cork Lacquered
Tile
TYPE OF FLOOR Engineered Cork
THICKNESS 11mm (wear layer 3mm)
LENGTH X WIDTH 612mm x 440mm
PACK SIZE 1.62m2
TYPE OF FINISH High Build UV Lacquered
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
DURABILITY Very high wear resistance
Estilo Prague Cork Lacquered Tile24-EPR-004
£65.95/m2 £54.96/m2 EX VAT
ES
TILO
CORK
118 All prices include VATCORK
Estilo Helsinki
Cork Lacquered
Tile
Looks like marble but with all the warmth and comfort of cork...
TYPE OF FLOOR Engineered Cork
THICKNESS 11mm (wear layer 3mm)
LENGTH X WIDTH 612mm x 440mm
PACK SIZE 1.62m2
TYPE OF FINISH High Build UV Lacquered
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES None or all 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
DURABILITY Very high wear resistance
Estilo Helsinki Cork Lacquered Tile With Bevel24-EHE-444
£67.95/m2 £56.63/m2 EX VAT
Estilo Helsinki Cork Lacquered Tile 24-EHE-004
£63.95/m2 £53.29/m2 EX VAT
ES
TILO
CORK
119All prices include VAT CORK
Estilo Barcelona
Cork Lacquered
Tile
Soft, comfortable, durable and highly water resistant...
TYPE OF FLOOR Engineered Cork
THICKNESS 11mm (wear layer 3mm)
LENGTH X WIDTH 612mm x 440mm
PACK SIZE 1.62m2
TYPE OF FINISH High Build UV Lacquered
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
DURABILITY Very high wear resistance
Estilo Barcelona Cork Lacquered Tile With Bevel24-EBA-444
£67.95/m2 £56.63/m2 EX VAT
ES
TILO
CORK
120 All prices include VATCORK
With more accentuated rustic colour variation...
Estilo Milan
Cork Lacquered
Tile
TYPE OF FLOOR Engineered Cork
THICKNESS 11mm (wear layer 3mm)
LENGTH X WIDTH 612mm x 440mm
PACK SIZE 1.62m2
TYPE OF FINISH High Build UV Lacquered
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
DURABILITY Very high wear resistance
Estilo Milan Cork Lacquered Tile With Bevel24-EMI-444
£67.95/m2 £56.63/m2 EX VAT
ES
TILO
CORK
121All prices include VAT CORK
Estilo Monte
Carlo Cork
Lacquered Tile
TYPE OF FLOOR Engineered Cork
THICKNESS 11mm (wear layer 3mm)
LENGTH X WIDTH 612mm x 440mm
PACK SIZE 1.62m2
TYPE OF FINISH High Build UV Lacquered
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
DURABILITY Very high wear resistance
Estilo Monte Carlo Cork Lacquered Tile24-EMC-004
£55.95/m2 £46.63/m2 EX VAT
ES
TILO
CORK
122 All prices include VATCORK
TYPE OF FLOOR Engineered Cork
THICKNESS 11mm (wear layer 3mm)
LENGTH X WIDTH 612mm x 440mm
PACK SIZE 1.62m2
TYPE OF FINISH High Build UV Lacquered
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
DURABILITY Very high wear resistance
Estilo Lisbon
Cork Lacquered
Tile
Estilo Lisbon Cork Lacquered Tile24-ELI-004
£55.95/m2 £46.63/m2 EX VAT
ES
TILO
CORK
123All prices include VAT CORK
LAMIN8WHAT’S SPECIAL ABOUT LAMIN8 FLOORING?
Lots! Our hard wearing, easy to install laminate
fl oors are extremely durable, very practical
and easy to maintain, yet off er the attractive
appearance of real wood.
These fl oors are made from the highest quality
High Density Fibreboard (HDF), guaranteeing the
integrity of the product. They are fi nished with a
decorative wood grain foil beneath a transparent
but hard wearing melamine surface.
All coatings comply with the AC3 heavy/
domestic/light commercial rating, so they’ll look
fantastic for years. They incorporate a patented
glueless joint system so they can be laid and relaid
many times with ease and confi dence.
LAM
IN8
LAM
IN8
124 All prices include VATLAMIN8
LAM
IN8
THE ADVANTAGES OF A LAMIN8 FLOOR:
• A superb range of authentic wood styles to suit your
taste and budget
• Perfectly closed joints
• The fl oor can be used immediately after installation
• No glue – no mess!
• High wear resistance rating.
OPTIONS AVAILABLE:
There are a choice of styles with embossed surfaces which
make it hard to distinguish from real wood surfaces.
To add the fi nal touch the plank fl oors can have micro-bevelled
edges to create the traditional long plank eff ect.
LAMIN8INSPIRED BY NATURE
40-VSO-12540-WSO-125
40-WDO-33840-WUB-742 40-WAM-67840-VCO-15540-WCO-155
40-WAW-21140-WCU-719 40-WWS-908 40-VMS-11240-WOR-137 40-WDS-64440-WWO-515 40-WWP-258 40-VBS-025
HIGH WEAR MELAMINE COATING
PRINTED WOOD FOIL
BALANCING MATERIAL
GLUELESS CLIC JOINT
HDF CORE
MATCHING TRIMS AVAILABLE MAINTENANCE PRODUCTS AVAILABLE P.26
8.3mm
LAM
IN8
125All prices include VAT LAMIN8
Lamin8 Oak
Select Plank
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES None or all 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Oak Select Plank With Bevel40-WS0-125
£18.95/m2 £15.79/m2 EX VAT
Lamin8 Oak Select Plank 40-VS0-125
£17.95/m2 £14.96/m2 EX VAT
LAM
IN8
LAM
IN8
126 All prices include VATLAMIN8
LAM
IN8
LAM
IN8
127All prices include VAT LAMIN8
Lamin8 Classic
Oak Plank
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES None or all 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Classic Oak Plank With Bevel40-WCO-155
£18.95/m2 £15.79/m2 EX VAT
Lamin8 Classic Oak Plank 40-VCO-155
£17.95/m2 £14.96/m2 EX VAT
LAM
IN8
LAM
IN8
128 All prices include VATLAMIN8
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Oak
Rustic Plank
Lamin8 Oak Rustic Plank With Bevel 40-WOR-137
£18.95/m2 £15.79/m2 EX VAT
LAM
IN8
LAM
IN8
129All prices include VAT LAMIN8
Lamin8 Urban
Oak Plank
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Urban Oak Plank With Bevel40-WUB-742
£18.95/m2 £15.79/m2 EX VAT
LAM
IN8
LAM
IN8
130 All prices include VATLAMIN8
LAM
IN8
LAM
IN8
All prices include VAT 131LAMIN8
Lamin8 Country
Oak Plank
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Country Oak Plank With Bevel40-WCU-719
£18.95/m2 £15.79/m2 EX VAT
LAM
IN8
LAM
IN8
132 All prices include VATLAMIN8
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Washed
Oak Plank
Lamin8 Washed Oak Plank With Bevel 40-WWO-515
£18.95/m2 £15.79/m2 EX VAT
LAM
IN8
LAM
IN8
133LAMIN8All prices include VAT
Lamin8 Dark
Oak Plank
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Dark Oak Plank With Bevel40-WDO-338
£18.95/m2 £15.79/m2 EX VAT
LAM
IN8
LAM
IN8
134 All prices include VATLAMIN8
LAM
IN8
LAM
IN8
135All prices include VAT LAMIN8
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 American
White Oak Plank
Lamin8 American White Oak Plank With Bevel40-WAW-211
£18.95/m2 £15.79/m2 EX VAT
LAM
IN8
LAM
IN8
136 All prices include VATLAMIN8
Lamin8 Dark
Sawn Plank
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Dark Sawn Plank With Bevel40-WDS-644
£18.95/m2 £15.79/m2 EX VAT
LAM
IN8
LAM
IN8
137All prices include VAT LAMIN8
Lamin8 American
Walnut Plank
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 American Walnut Plank With Bevel40-WAM-678
£18.95/m2 £15.79/m2 EX VAT
LAM
IN8
LAM
IN8
138 All prices include VATLAMIN8
LAM
IN8
LAM
IN8
139All prices include VAT LAMIN8
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Oak
White Smoked
Plank
Lamin8 Oak White Smoked Plank With Bevel40-WWS-908
£18.95/m2 £15.79/m2 EX VAT
LAM
IN8
LAM
IN8
140 All prices include VATLAMIN8
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES All 4 edges
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Walnut
Plank
Lamin8 Walnut Plank With Bevel40-WWP-258
£18.95/m2 £15.79/m2 EX VAT
LAM
IN8
LAM
IN8
141All prices include VAT LAMIN8
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Maple
Select 3 Strip
Lamin8 Maple Select 3 Strip40-VMS-112
£17.95/m2 £14.96/m2 EX VAT
LAM
IN8
LAM
IN8
142 All prices include VATLAMIN8
Lamin8 Beech
Select 3 Strip
TYPE OF FLOOR Laminate
THICKNESS 8.3mm
LENGTH X WIDTH 1215mm x 196mm
PACK SIZE 1.905m2
TYPE OF FINISH Embossed Grain
TYPE OF JOINT Glueless Clic System
BEVELS ON EDGES None
METHOD OF FIXING Floated
UNDERFLOOR HEATING Suitable
HARDNESS Hard
DURABILITY High wear resistance
Lamin8 Beech Select 3 Strip40-VBS-025
£17.95/m2 £14.96/m2 EX VAT
LAM
IN8
LAM
IN8
143All prices include VAT LAMIN8
VUSTAWHY NOT LOOK AT VUSTA DESIGN FLOORING?
Vusta Design Flooring replicates the beauty and texture of natural materials, using the same styles and designs such as planks and tiles with and without bevels, with light or heavily embossed surfaces and even with synchronised embossing, where the individual pores of the wood or stone are synchronised with the print of the grain to give an authentic look which is hard to differentiate from the real thing. It offers the ultimate mix of versatile design and affordable quality.
144 All prices include VATVUSTA
Ideal in living areas Perfect for wet rooms Suitable for commercial use
Visit our NEW website
www.vusta.co.uk
All prices include VAT 145VUSTA
For a small fee you can
also upload your own
room set photos
HOW THE ROOM DESIGNER WORKS:
• Visit www.vusta.co.uk to get started
• Launch the Room Designer by
clicking on the icon
• Select a room design
• Choose your fl ooring
• Change the wall colour
• Select the laying angle
• Include design strips?
• Save, print or share your designs
Add design strips...
Change the wall colour...
Choose the fl oor...
ROOM DESIGNERVISUALISE YOUR LIVING SPACE ONLINE
PACK CALCULATORLET US DO THE HARD WORK FOR YOU...
RANGEPer Pack m2
1 2 3 4 5 6 7 8 9 10
SOLID
York 2.29 4.58 6.87 9.16 11.45 13.74 16.03 18.32 20.61 22.9
York Narrow Plank 1.584 3.168 4.752 6.336 7.92 9.504 11.088 12.672 14.256 15.84
Dunster 140mm 1.68 3.36 5.04 6.72 8.4 10.8 11.76 13.44 15.12 16.8
Dunster 160mm 1.92 3.84 5.76 7.68 9.6 11.52 13.44 15.36 17.28 19.2
Dunster 180mm 2.16 4.32 6.48 8.64 10.8 12.96 15.12 17.28 19.44 21.6
Flink 1.5 3 4.5 6 7.5 9 10.5 12 13.5 15
Denbigh 230mm 0.515 1.03 1.545 2.06 2.575 3.09 3.605 4.12 4.635 5.15
Denbigh 280mm 0.627 1.254 1.881 2.508 3.135 3.762 4.389 5.016 5.643 6.27
ENGINEERED
Raglan Oak 2.2 4.4 6.6 8.8 11 13.2 15.4 17.6 19.8 22
Raglan Walnut & Maple 1.05 2.1 3.15 4.2 5.25 6.3 7.35 8.4 9.45 10.5
Harlech Eco 1.587 3.174 4.761 6.348 7.935 9.522 11.109 12.696 14.283 15.87
Harlech Wide plank 2.1 4.2 6.3 8.4 10.5 12.6 14.7 16.8 18.9 21
Harlech plank 1.65 3.3 4.95 6.6 8.25 9.9 11.55 13.2 14.85 16.5
Harlech Magnum 2.11 4.22 6.33 8.44 10.55 12.66 14.77 16.88 18.99 21.1
Harlech Magnum Narrow Plank 1.65 3.3 4.95 6.6 8.25 9.9 11.55 13.2 14.85 16.5
Windsor Oak Unique 3 Strip 3.587 7.174 10.761 14.348 17.935 21.522 25.109 28.696 32.283 35.87
Windsor Plank 3.203 6.406 9.609 12.812 16.015 19.218 22.241 25.624 28.827 32.03
Chepstow Planed 2.11 4.22 6.33 8.44 10.55 12.66 14.77 16.88 18.99 21.1
Chepstow Aged & Distressed 1.444 2.888 4.332 5.776 7.22 8.664 10.108 11.552 12.996 14.44
DESIGNER
Goodrich Herringbone 1.08 2.16 3.24 4.32 5.4 6.48 7.56 8.64 9.72 10.8
Chepstow Sawn 2.11 4.22 6.33 8.44 10.55 12.66 14.77 16.88 18.99 21.1
Arundel 3.203 6.406 9.609 12.812 16.015 19.218 22.421 25.624 28.827 32.03
BAMBOO
Warwick 2.166 4.332 6.498 8.664 10.83 12.996 15.162 17.328 19.494 21.66
Style 1.532 3.064 4.596 6.128 7.66 9.192 10.724 12.256 13.788 15.32
CORK
Estilo 1.62 3.24 4.86 6.48 8.1 9.72 11.34 12.96 14.58 16.2
LAMIN8
Lamin8 1.905 3.81 5.715 7.62 9.525 11.43 13.335 15.24 17.145 19.05
146 All prices include VATPACK CALCULATOR
Terms & ConditionsIn the unlikely event that goods are delivered wrong or damaged,
it is the responsibility of the customer to ensure sufficient time is
allowed for a replacement to be sent.
1. DEFINITIONS
In these terms and conditions, the following words shall have
the following meanings:
“Buyer” shall mean any person, firm or company, to whom
the Company supplies Goods or Services or with whom the
Company enters into negotiations for the supply of Goods
or Services.
“Company” shall mean Woodpecker Trading Company trading
as Kenton Floors.
“Goods” shall mean products, articles or things which are
supplied by or which are the subject of negotiations for supply
by the Company to the Buyer.
“Services” shall mean services are supplied by or which are the
subject of negotiations/or supply by the Company to the Buyer.
2. MAKING THE CONTRACT
2.1 The Company’s salesmen are not authorised representatives
and are not authorised to accept confirm or vary any order nor to
make any representation or promise on the Company’s behalf
2.2 Any estimate/quotation which comprises an invitation to
treat is open for a period of 30 days only from the date thereof,
provided that the Company has not previously withdrawn it.
Any order issued by the Buyer is subject to acceptance by the
Company and a contract will only be formed when the Company
has accepted the Buyer’s offer to buy in writing. Any offer made
by the Buyer must be confirmed in writing by the Buyer.
2.3 All orders are placed under these terms and conditions alone.
2.4 These terms and conditions exclude any other terms and
conditions inconsistent therewith which a Buyer might seek to
impose even though such other terms and conditions may be
submitted in a later document and/or purport to exclude or
supersede any terms or conditions with them or may be
contained in any offer acceptance or counter-offer made by
the Buyer.
2.5 All floors supplied by the Company must be fitted in
accordance with BS8201 (1987).
2.6 No variation of these terms and conditions is permitted
unless expressly accepted by a Director of the firm in writing.
3. CANCELLATION
3.1 No cancellation by the Buyer is permitted except where
expressly agreed by a Director of the Company in writing.
3.2 The Buyer will in the event of agreed cancellation by the
Buyer indemnify the Company fully against all expenses incurred
up to the time of such cancellation together with by way of
liquidated damages a sum of 33 1/3% of the contract price which
shall be paid by the Buyer to the Company forthwith,
4. PRICE
4.1 All prices quoted are those ruling at the date of dispatch
or supply.
4.2 Unless otherwise stated all prices quoted are net, exclusive of
VAT, and in the case of Goods ex works.
4.3 The Company reserves the right at any time prior to delivery
of the Goods or supply of Services to adjust the price to take
account of any increase in the cost of raw materials, labour or
services or any currency fluctuations affecting the cost of
imported materials or services.
5. TERMS OF PAYMENT
5.1 All sums become due and payable under these terms and
conditions not later than 14 days from date of invoice.
5.2 Time for payment shall be of the essence.
5.3 The Company reserves the right to charge interest at 2.5 per
centum per month on all overdue accounts, such interest being
deemed to accrue on a day to day basis from the due date for
payment under clause 5.1.
5.4 The Buyer shall have no right to set off, statutory or
otherwise.
5.5 If the Buyer (being a Company) has a petition for its
winding-up or passes a resolution for voluntary winding-up
otherwise than for the purpose of a bona fide amalgamation or
reconstruction or compounds with its creditors or has a receiver
appointed or all or any part of its assets or (being an individual)
becomes bankrupt or insolvent or enters into any arrangement
with its creditors or commits a material or serious breach of this
Agreement (and in the case of such a breach being remediable
fails to remedy it within 7 days of receiving notice to do so) he
will be deemed to have repudiated the Contract.
5.6 The Company reserves the right at any time at its discretion
to demand security for payment before continuing with or
delivering any Order, supplying any Goods or Services.
5.7 The Buyer accepts that in the event of non payment within
the payment period the Company will resort to legal action
to recover the debt in this instance a 20% surcharge will be
added to the outstanding amount to cover administration and
agents fees.
5.8 Where the Buyer is a company the directors agree to
guarantee payment personally, both jointly and severally, of any
outstanding amounts due in the event of their company being
unable to meet its financial commitments or becoming insolvent.
6. DELIVERY
6.1 Delivery will be deemed to have been effected when the
Goods are ready for collection at the premises of the Company
or as the case may be the premises of the suppliers to the
Company in circumstances where the Gods are delivered direct
from such suppliers.
6.2 Time of delivery is not of the essence.
6.3 The Company shall not be liable for any loss whatsoever or
howsoever arising caused by its non-delivery or by the failure to
make Goods ready for collection on the due date.
6.4 The Company reserves the right to make delivery by
installments and to tender a separate invoice in respect of each
installment.
6.5 When delivery is to be by installments or the Company
exercises its right to deliver by installments under clause 6.4
hereof or if there be delay in the delivery of any one or more
installments for whatever reason this will not entitle the Buyer to
treat the contract as repudiated and/or to damages.
6.6 Deviations in quantity between the Goods delivered and
Goods ordered representing not more than 10 per cent by value
shall not give the Buyer any right to reject the Goods or to claim
damages and the Buyer shall be obliged to accept and pay at the
contract rate for the quantity of the Goods delivered.
7. SUPPLY OF SERVICES
7.1 Time for the supply of Services is not of the essence.
7.2 The Company shall not be liable for any loss whatsoever or
howsoever arising caused by its failure to supply Services or any
part thereof on the due date.
7.3 The Company reserves the right to supply Services by
installments and to tender a separate invoice in respect of each
installment.
7.4 When the supply of Services is to be by installments or the
firm exercises its right to supply Services by installments under
clause 7.3 hereof or if there be a delay in the supply of any one
or more installments of Services for whatever reason this will
not entitle the Buyer to treat the contract as repudiated or
to damages.
7.5 Deviation in the quantity between Services supplied and the
Services ordered representing not more than 10 per cent by value
shall not give the Buyer any right to reject the Services or to claim
damages and the Buyer shall be obliged to accept and pay at the
contract rate for the quantity of the Services supplied.
8. RISK AND THE PASSING OF PROPERTY IN GOODS
8.1 Risk in the Goods shall pass to the Buyer when the Goods
are delivered.
8.2 Notwithstanding risk in the Goods passing in accordance
with clause 8.1 hereof title in the Goods shall not pass to the
Buyer until whichever shall be the first to occur of the following:-
8.2.1 payment being received by
the Company for the Goods and Services and no other amounts
then being outstanding from the Buyer to the Company in
respect of other Goods or Services supplied by the Company
8.2.2 the Buyer selling the Goods in accordance with the
provisions of these terms and conditions in which case title to the
Goods shall be deemed to have passed to the Buyer immediately
prior to delivery of the Goods to the Buyer’s customers; and
8.2.3 the Company waiving its rights under this clause 8.2 in
respect of specified Goods or Services whereupon title to the said
Goods shall forthwith vest in the Buyer.
8.3 The Buyer is licensed by the Company to use or to agree to
sell the Goods delivered to the Buyer subject to the express
condition that the entire proceeds of any sale are held in trust for
the Company and are not mixed with other moneys or paid into
an overdrawn bank account and shall at all times be identifiable
as the Company’s moneys.
8.4 Until title to the Goods passes:
8.4.1 The Buyer will hold the Goods as fiduciary agent and bailee
for the Company;
8.4.2 the Goods shall, subject to clause 8.3, be kept separate and
distinct from all other property of the Buyer and of third parties
and in good and substantial repair and condition and be stored in
such a way as to be clearly identifiable as belonging to the
Company;
8.4.3 the Company may at any time revoke the power of sale and
use contained in clause 8.3 by notice to the Buyer if the Buyer is
in default for longer than 14 days in the payment of any sum
whatsoever due to the Company (whether in respect of the
Goods or any other Goods or Services supplied at any time by it
to the Buyer) or if the Company has bona fide doubts as to the
solvency of the Buyer;
8.4.4 The Buyer’s power of sale and use contained in clause 8.3
shall automatically cease if the Buyer has a petition presented for
its winding-up or passes a resolution for voluntary winding-up
otherwise than for the purpose of a bona fide amalgamation or
reconstruction or compounds with its creditors or has a receiver
appointed of all or any part of its assets or becomes bankrupts
or insolvent or enters into any arrangements with creditors or
takes or suffers any similar action in consequence of debts or
carries out or undergoes any analogues act or proceeding under
foreign law;
8.4.5 upon determination of the Buyer’s power of sale and use
pursuant to clause 8.4.3 or clause 8.4.4. the Buyer shall place any
of the Goods in its possession or under its control and unsold at
the disposal of the Company and the Company shall be entitled
to enter upon any premises of the Buyer for the purpose of
removing such Goods.
8.5 The Company shall at any time be entitled to appropriate any
payments made by the Buyer in respect of any Goods or Services
in settlement of such invoices or accounts in respect of such
Goods or Services as the Company may in its absolute discretion
think fit notwithstanding any purported appropriation to the
contrary by the Buyer.
9. LIEN AND STOPPAGE
9.1 Until such time as the title in the Goods has passed to the
Buyer the Company has the right to withhold delivery if the Buyer
(being a Company) has a petition presented for its winding-up or
passes a resolution for voluntary winding-up otherwise than for
the purpose of a bona fide amalgamation or reconstruction or
compounds with its creditors or has a receiver appointed of all or
any part of its assets or (being an individual) becomes bankrupt
or insolvent or enters into any arrangements with creditors or
takes or suffers any similar action in consequence of debts or
carries out or undergoes any analogous act or proceedings under
foreign law.
9.2 When the title in the Goods has passed to the Buyer and the
time for payment has fallen due but payment has not been made
or if the Buyer (being a Company) has a petition presented for its
winding-up or passes a resolution for voluntary winding-up
otherwise than for the purposes of a bona fide amalgamation or
reconstruction or compounds with its creditors or has a receiver
appointed of all or any part of its assets or (being an individual)
becomes bankrupt or insolvent or enters into any arrangements
with creditors or takes or suffers any similar action in
consequence of debts or carries out or undergoes any analogous
act or proceedings under foreign law the Company has
9.2.1 a lien on the Goods so long as the Company is in possession
of them
9.2.2 a right of stoppage in transit
9.2.3 a right of resale
9.3 For the avoidance of doubt it is hereby declared that nothing
in this clause shall affect the rights given to the Company by
ss.38–48 of the Sale of Goods Act 1979.
10. INSPECTION/SHORTAGES
10.1 The Buyer is under a duty to inspect the Goods forthwith on
delivery and satisfy himself as to the due performance of Services
forthwith after supply.
10.2 The Company shall be under no liability for any defects or
shortages that would be apparent on careful inspection if the
terms of this clause are not complied with, and, in any event will
be under no liability if a written complaint is not delivered to the
Company within 7 days of delivery or supply detailing the alleged
detect or shortage.
10.3 In all cases where defects or shortages in respect of Goods
are complained of the Company shall be under no liability in
respect thereof unless an opportunity to inspect the Goods is
given to the Company before any use is made thereof or any
alteration or modification is made thereto by the Buyer.
10.4 Subject to clauses 10.2 and 10.3 the Company shall make
good any defect or shortage in the Goods and where appropriate
replace any Goods damaged in transit as soon as it is reasonably
able to do so, but otherwise shall be under no liability whatsoever
or howsoever arising from such defect, shortage or damage.
10.5 Subject to clause 10.4 the Company shall remedy any defect
in the supply of Services as soon as it is reasonably able to do so
but otherwise shall be under no liability whatsoever or howsoever
arising from such defect
11. WARRANTY
11.1 No representation or warranty is given as to the suitability or
fitness of the Goods or Services for any particular purpose and
the Buyer shall satisfy himself in this respect and shall be totally
responsible therefore
11.2 If the Goods are in such a state or the Services so defectively
supplied as would but for this condition entitle the Buyer to
repudiate the contract and/or claim damages from the Company
the Company reserves the right to repair or replace the Goods or
perform the Services (or the relevant part thereof) again.
12. LIABILITY
12.1 Introduction
12.1.1 Nothing in clause 12 shall be deemed to exclude or restrict
the Company’s liability for death or personal injury resulting from
negligence.
12.1.2 Each of the sub-clauses in clause 12 is to be treated as
separate and independent
12.1.3 The Company is willing to undertake liability additional to
that provided by this clause in exchange for a higher price
12.2 Exclusion
12.2.1 Clause 12.2 only covers defects caused by faulty design,
manufacture, materials or workmanship. It does not cover
defects caused by abnormal use, misuse or neglect.
12.2.2 The Company agrees that if any defect covered by clause
12.2 is discovered during the period of three months commencing
with the date of delivery or supply, the Company will remedy any
defect at its own expense or, in the case of Goods if it chooses to
do so, replace them.
12.2.3 The Buyer cannot claim the benefit of this clause unless
– he informs the Company of the relevant defect in writing within
7 working days of discovering it; and – in the case of Goods he
returns the Goods to the Company at his own expense
12.2.3a The company will not accept any liability for defects in
goods once they have been fitted. It is the buyers responsibility to
check the goods prior to installation.
12.2.4 The risk of accidental loss whilst the Goods are being
returned will be borne by the Buyer
12.2.5 In consideration for receiving the benefit of this clause,
the Buyer agrees that, apart from those terms set out in clause
10 and 11, all other terms, whether conditions, warranties or
innominate terms, express or implied, statutory or otherwise, are
excluded from the contract between the Company and the Buyer
to the extent permitted by law (except where the Buyer deals as
consumer within section 12 of the Unfair Contract Terms Act
1977 when the terms implied by sections 13, 14 and 15 of the Sale
of Goods Act 1979 shall be implied into the contract).
12.3 Exclusion of Consequential Loss.
The Company shall not be liable for any consequential or indirect
loss suffered by the Buyer whether this loss arises from breach of
a duty in contract or tort or in any other way (including loss
arising from the Company’s negligence).
Non-exhaustive illustrations of consequential or indirect loss
would be
– loss of profits
– loss of contracts
– damage to property of the Buyer or anyone else, and
– personal injury to the Buyer or anyone else (except so far as
such injury is attributable to the Company’s negligence)
12.4 Limitation
The Company’s total liability for any one claim or for the total
of all claims arising from any one act or default of the Company
(whether arising from the Company’s negligence or otherwise)
shall not exceed £1000 0r the contract price whichever is
the greater.
13. FORCE MAJEURE
13.1 The Company shall not be liable for any failure to deliver the
Goods or perform the Services arising from circumstances
outside the Company’s control.
13.2 Non-exhaustive illustrations of such circumstances would
be act of God, war, riot, explosion, abnormal weather conditions,
fire, flood, strikes, lockouts, Government action or regulations
(UK or otherwise), delay by suppliers, accidents and shortage
of materials, labour or manufacturing facilities.
13.3 Should the Company be prevented from delivering the
Goods or performing the Services in the above circumstances,
it shall give the Buyer written notice of this fact as soon as
reasonably practicable after discovering it.
13.4 If the circumstances preventing delivery of the Goods or
performing the Services are still continuing three months after
the Buyer receives the Company’s notice, then either party may
give written notice to the other cancelling the contract.
13.5 If the contract is cancelled in this way, the Company will
refund any payment which the Buyer has already made on
account of the price (subject to deduction of any amount the
Company is entitled to claim from the Buyer) but the Company
will not be liable to compensate the Buyer for any further loss or
damage caused by the failure to deliver the Goods or perform
the Services.
14. SALES PROMOTION DOCUMENTATION
Whilst the Company takes every precaution in the preparation of
its catalogue, technical circulars, price lists and its other literature,
these documents are for the Buyer’s general guidance only and
the particulars contained therein shall not constitute
representations by the Company and the Company shall not be
bound thereby.
15. NOTICES
Any notice to be given hereunder shall be in writing and shall
be deemed to have been duly given if sent or delivered to the
party concerned at its address specified overleaf or such other
address as that party may from time to time notify in writing and
shall be deemed to have been served, if sent by post, 48 hours
after posting.
16. CANCELLATION
The Company is prepared to accept the cancellation of a contract
provided that it is in writing and is received by the Company:
(a) in the case of special orders before the manufacture of the
goods has commenced:
(b) in the case of goods ordered from stock before the goods
have been despatched.
(c) but subject to liability for any losses incurred by the Company
in disposing of the goods.
17. MATCHING
For technical reasons it is not always possible to obtain an exact
colour match between different production batches which have
the same colour description. The Company therefore
recommends that all products should be of the same batch. The
Company will be under no liability whatsoever in respect of any
mismatching of tiles and sheet with the same colour description
where the tiles and sheet are of different batches.
18. ADVICE AND WARNINGS
(a) Without prejudice to any of the Company’s rights under these
terms or common law or statute the Company shall not be liable
for any loss or damage suffered by the Buyer or any third party
as a result of failure to follow any of the Company’s
recommendations with regard to the goods.
19. STILETTO HEELS
Where Stiletto heeled shoes are in use, floors are liable to suffer
damage from intense point loading pressure. We therefore
cannot be held responsible for any loss in appearance where such
heels are in use.
20. SUITABILITY OF GOODS
If requested in writing to do so, we will use our utmost
endeavours to give sound and honest advice as to the suitability
of goods sold by us for a particular use or purpose, but we do not
represent or warrant (and nobody has authority to represent or
warrant) the fitness of any goods for any particular purpose or
use, whether such use or purpose is known to us or not or any
advice requested regarding installation.
21. ASSIGNMENT
The Buyer shall not assign or purport to assign or transfer the
contract or the benefits thereof to any other person without prior
written consent of the other.
22. PROPER LAW AND JURISDICTION
The Contract shall be governed by and construed in accordance
with English law and all disputes arising in connection with
the contract shall be submitted to the jurisdiction of the
English Courts.
23. HEADINGS
The headings of these conditions are for convenience only and
shall have no effect on the interpretation thereof.
Revision Date: June 2012
Kenton Floors, Caerphilly CF83 8DR
Tel: 02920 888223
Kenton Floors reserves the right to update and amend these
terms and conditions without notice.
All prices include VAT 147TERMS & CONDITIONS
Your Woodpecker Stockist
Kenton Floors
Woodpecker House
29 Pant Glas Industrial Estate
Bedwas, Caerphilly CF83 8DR
T: 02920 888223 F: 02920 881694
www.woodpeckerflooring.co.uk