Chapter 14 Control Unit...

YonseiYonsei UniversityUniversity

Chapter 14Chapter 14

Control Unit Operation

YonseiYonsei UniversityUniversity14-2

ContentsContents

• Micro-Operation• Control of the Processor• Hardwired Implementation


MicroMicro--OperationsOperations

• Micro refers to the fact that each step is very simple and accomplishes very little

• The execution of a program consists of the sequential execution of instructions

• Each instruction is executed during an instruction cycle made up of shorter subcycles

• The performance of each subcycleinvolves one or more shorter operations, that is, micro-operations

Micro-Operations


Constituent ElementConstituent Element Micro-Operations


The Fetch CycleThe Fetch Cycle

• Four involved registers.– Memory address register (MAR) :

• Is connected to the address lines of the system bus• It specifies the address in memory for a read or write

operation

– Memory buffer register (MBR) : • Is connected to the data lines of the system bus• It contains the value to be stored in memory or the last

value read from memory

– Program counter (PC) : • Holds the address of the next instruction to be fetched

– Instruction register (IR) : • Holds the last instruction fetched

Micro-Operations


Sequence of Events, Fetch CycleSequence of Events, Fetch Cycle

(a) Beginning

Micro-Operations



(b) First Step

Micro-Operations



(c) Second Step

Micro-Operations



(d) Third Step

Micro-Operations


The Fetch CycleThe Fetch Cycle –– SequenceSequence

(a) Beginning : the address of the next instruction to be executed is in the PC

(b) First step : move that address to the MAR

(c) Second step : bring in the instruction The desired address is placed on the address bus, the control unit issues a READ command on the control bus, and the result appears on the data bus and is copied into the MBR

(d) Third step : move the contents of the MBR to the IR

This free up the MBR for use during a possible indirect cycle

Micro-Operations


The Fetch CycleThe Fetch Cycle –– SequenceSequence

•Symbolic presentationt1: MAR ? (PC)t2: MBR ? Memory

PC ? (PC) + It3: IR ? (MBR)

•Micro-operation grouping rules1. The proper sequence of events must be followed2. Conflicts must be avoided

•Micro-operation involve an addition- This addition could be performed by the ALU- The use of the ALU may involve additional

micro-operations

Micro-Operations


The Indirect CycleThe Indirect Cycle

• Indirect addressing

t1: MAR ? (IR(Address))t2: MBR ? Memoryt3: IR(Address) ? (MBR(Address))

Micro-Operations


The Interrupt CycleThe Interrupt Cycle

t1: MBR ? (PC)t2: MAR ? Save_Address

PC ? Routine_Addresst3: Memory ? (MBR)

Micro-Operations


The Execute CycleThe Execute Cycle

• ADD R1, Xt1: MAR ? (IR(address))t2: MBR ? Memoryt3: R1 ? (R1) + (MBR)

• ISZ X (increment and skip if zero)t1: MAR ? (IR(address))t2: MBR ? Memoryt3: MBR ? (MBR) + 1t4: Memory ? (MBR)

If((MBR) = 0) then (PC ? (PC) +I)

Micro-Operations


The Execute CycleThe Execute Cycle

• BSA X (branch and save address)

t1: MAR ? (IR(address))MBR ? (PC)

t2: PC ? (IR(address))Memory ? MBR

t3: PC ? (PC) + I

Micro-Operations


The Instruction CycleThe Instruction Cycle

• There is one sequence each for the fetch, indirect, and interrupt cycle, and, for the execute cycle, there is one sequence of micro-operation for each opcode

• Instruction cycle code(ICC)00: Fetch01: Indirect10: Execute11: Interrupt

Micro-Operations


Flowchart for Instruction CycleFlowchart for Instruction CycleMicro-Operations


Functional RequirementsFunctional Requirements

• The following three-step process leads to a characterization of the control unit:– Define the basic elements of the processor– Describe the micro-operations that the processor

performs– Determine the functions that the control unit must

perform to cause the micro operations to be performed

• Basic functional elements– ALU– Register– Internal data paths– External data paths– Control unit

Control Of The Processor


Functional RequirementsFunctional Requirements

• The reader should see that all micro-operations fall into the following categories– Transfer data from one register to another– Transfer data from a register to an external interface– Transfer data from an external interface to a register– Perform an arithmetic or logic operation, using

registers for input and output

• The control unit perform two basic tasks– Sequencing– Execution



Control SignalsControl Signals

• Inputs– Clock – Instruction register– Flags

• Outputs– Control signals within the processor– Control signals to control bus



Model of Control UnitModel of Control Unit Control Of The Processor


Model of Control UnitModel of Control Unit Control Of The Processor


Control SignalsControl Signals

• A control signal that opens gates, allowing the contents of the MAR onto the address bus

• A memory read control signal on the control bus

• A control signal that opens the gates, allowing the contents of the data bus to be stored in the MBR

• Control signals to logic that add 1 to the contents of the PC and store the result back to the PC



A Control Signals ExampleA Control Signals Example

• Control signals go to three separate destinations– Data paths– ALU– System bus



Data Paths and Control SignalsData Paths and Control Signals Control Of The Processor


MicroMicro--operation and Control Signalsoperation and Control Signals Control Of The Processor


Internal Processor OrganizationInternal Processor Organization

• The ALU and all processor registers are connected by a single internal bus

• Gates and control signals are provided for movement of data onto and off the bus from each register

• Two new registers,labeled Y and Z, have been added to the organization



CPU with Internal BusCPU with Internal Bus Control Of The Processor


Internal Processor OrganizationInternal Processor Organization

• An operation to add a value from memory to the AC would have the following steps:

t1: MAR<-(IR(address))t2: MBR<-Memory t3: Y<-(MBR)t4: Z<-(AC) + (Y)t5:AC<-(Z)

• Register Y provide temporary storage for the other input

• Register Z provide temporary output storage



The Intel 8085The Intel 8085

• Incrementer/decrementer address latch– Logic that can add 1 to or subtract 1 from the

contents of the stack pointer or program counter

• Interrupt control– This module handles multiple levels of interrupt

signals

• Serial I/O control– This module interfaces to devices that

communicate 1 bit at a time



Intel 8085 CPU Block DiagramIntel 8085 CPU Block Diagram Control Of The Processor


Intel8085 External SignalsIntel8085 External Signals Control Of The Processor


Intel 8085 External SignalsIntel 8085 External Signals Control Of The Processor


Intel 8085 Pin ConfigurationIntel 8085 Pin Configuration Control Of The Processor


• The control unit is identified as having two components labeled

(1) instruction decoder and machine cycle encoding(2) Timing and control

• Timing and control– accepts as inputs clock, current instruction and some

external control signal

• Each instruction cycle is divided into from one to five machine cycles

• The number of machine cycles is fixed for a given instruction but varies from one instruction to another


Timing and controlTiming and control


Timing DiagramTiming Diagram Control Of The Processor


Hardwired ImplementationHardwired Implementation• Control unit implementation

– Hardwired implementation– Microprogrammed implementation

Hardwired Implementation


Control Unit InputsControl Unit Inputs• The key inputs are the instruction register,

the clock, flags, and control bus signals• To simplify the control unit logic, there

should be a unique logic input for each opcode

• Decoder– Takes an encoded input and produces a single

output

• The clock portion of the control unit issues a repetitive sequence of pulses



DecoderDecoder Hardwired Implementation


Control Unit with Decoded InputsControl Unit with Decoded Inputs Hardwired Implementation


Control Unit LogicControl Unit Logic• Derive a Boolean expression of that signal

as a function of the inputs• Define two new control signal, P and Q

PQ = 00 Fetch CyclePQ = 01 Indirect CyclePQ = 10 Execute CyclePQ = 11 Interrupt Cycle



Control Unit LogicControl Unit Logic

• The task of implementing a combinatorial circuit that satisfies all of these equations becomes extremely difficult

• The results is that a far simpler approach– Microprogramming


Date post:	10-May-2020
Category:	Documents
Upload:	others
View:	9 times
Download:	0 times

Chapter 14 Control Unit...

Documents