UNIT KEJURUTERAAN ALAM SEKITAR UNIT KEJURUTERAAN ALAM SEKITAR JABATAN KEJURUTERAAN AWAM JABATAN KEJURUTERAAN AWAM

POLITEKNIK SULTAN IDRIS SHAH

CHAPTER 4CHAPTER 4

AIR POLLUTION CONTROL AIR POLLUTION CONTROL AND TECHNOLOGIESAND TECHNOLOGIES

2

Upon completion of this course, student should be able to :

Identify air pollution control for particle pollutant Choose air pollution control device for particle pollutant Understand air pollution control method for gas

pollutant Describe adsorption method for control gas pollutant Describe absorption method for control gas pollutant Describe condensation method for control gas pollutant

Technology for Air Pollution Control

Techniques Without Using Emissions Control Devices Process Change

Wind, Geothermal, Hydroelectric, or Solar Unit instead of Fossil fired Unit.

Change in Fuel e.g. Use of Low Sulfur Fuel, instead of High Sulfur fuel.

Good Operating Practices Good Housekeeping Maintenance

Plant Shutdown

Commonly Used Methods For Air Pollution ControlPARTICULATE

Cyclones Electrostatic Precipitators Fabric Filter Wet Scrubbers

GASES Adsorption Towers Thermal Incernation Catalytic Combustion

SOx CONTROL

GENERAL METHODS FOR CONTROL OF SO2 EMISSIONS Change to Low Sulfur Fuel

Natural Gas Liquefied Natural Gas Low Sulfur Oil

Low Sulfur Coal

Use Desulfurized Coal and Oil Increase Effective Stack Height Build Tall Stacks Redistribution of Stack Gas Velocity Profile Modification of Plume Buoyancy

General Methods for Control of SO2 Emissions (contd.) Use Flue Gas Desulfurization Systems

Use Alternative Energy Sources, such as Hydro-Power or Nuclear-Power

Flue Gas Desulfurization SO2 scrubbing, or Flue Gas Desulfurization processes

can be classified as: Throw away or Regenerative, depending upon whether the recovered

sulfur is discarded or recycled. Wet or Dry, depending upon whether the scrubber is a liquid or a solid.

Flue Gas Desulfurization Processes The major flue gas desulfurization ( FGD ), processes are : Limestone Scrubbing Lime Scrubbing Dual Alkali Processes Lime Spray Drying Wellman-Lord Process

Limestone Scrubbing Limestone slurry is sprayed on the incoming flue

gas. The sulfur dioxide gets absorbed The

limestone and the sulfur dioxide react as

follows :

CaCO3 + H2O + 2SO2 ----> Ca+2 + 2HSO3-+ CO2

CaCO3 + 2HSO3-+ Ca+2 ----> 2CaSO3 + CO2 +

H2O

Limestone Scrubbing

Lime Scrubbing

Lime Scrubbing The equipment and the processes are similar to those

in limestone scrubbing Lime Scrubbing offers better utilization of the reagent. The operation is more flexible. The major disadvantage is the high cost of lime compared to limestone.

The reactions occurring during lime scrubbing are :

CaO + H2O -----> Ca(OH)2

SO2 + H2O <----> H2SO3

H2SO3 + Ca(OH)2 -----> CaSO3.2 H2OCaSO3.2 H2O + (1/2)O2 -----> CaSO4.2 H2O

Dual Alkali System Lime and Limestone scrubbing lead to deposits inside spray tower. The deposits can lead to plugging of the nozzles through which the

scrubbing slurry is sprayed. The Dual Alkali system uses two regents to remove the sulfur

dioxide. Sodium sulfite / Sodium hydroxide are used for the absorption of

sulfur dioxide inside the spray chamber. The resulting sodium salts are soluble in water,so no deposits are

formed. The spray water is treated with lime or limestone, along with make-

up sodium hydroxide or sodium carbonate. The sulfite / sulfate ions are precipitated, and the sodium

hydroxide is regenerated.

Lime – Spray DryingLime Slurry is sprayed into the chamber

The sulfur dioxide is absorbed by the slurry

The liquid-to-gas ratio is maintained such that the spray dries before it reaches the bottom of the chamber

The dry solids are carried out with the gas, and are collected in fabric filtration unit

This system needs lower maintenance, lower capital costs, and lower energy usage

Wellman – Lord Process This process consists of the following

subprocesses: Flue gas pre-treatment. Sulfur dioxide absorption by sodium sulfite Purge treatment Sodium sulfite regeneration. The concentrated sulfur dioxide stream is processed to a

marketable product.

The flue gas is pre - treated to remove the particulate. The sodium

sulfite neutralizes the sulfur dioxide : Na2SO3 + SO2 + H2O -----> 2NaHSO3

Wellman – Lord Process (contd.) Some of the Na2SO3 reacts with O2 and the SO3 present in the flue

gas to form Na2SO4 and NaHSO3.

Sodium sulfate does not help in the removal of sulfur dioxide, and

is removed. Part of the bisulfate stream is chilled to precipitate the

remaining bisulfate. The remaining bisulfate stream is evaporated

to release the sulfur dioxide, and regenerate the bisulfite.

Wellman – Lord ProcessSchematic process flow diagram – SO2 scrubbing and recovery system

NOX CONTROL

Background on Nitrogen Oxides

There are seven known oxides of nitrogen : NO

NO2

NO3

N2O

N2O3

N2O4

N2O5

NO and NO2 are the most common of the seven oxides listed

above. NOx released from stationary sources is of two types

General Methods For Control Of NOx Emissions

NOx control can be achieved by: Fuel Denitrogenation

Combustion Modification

Modification of operating conditions

Tail-end control equipment Selective Catalytic Reduction

Selective Non - Catalytic Reduction

Electron Beam Radiation

Staged Combustion

Fuel Denitrogenation

o One approach of fuel denitrogenation is to remove a large part of the

nitrogen contained in the fuels. Nitrogen is removed from liquid fuels

by mixing the fuels with hydrogen gas, heating the mixture and using a

catalyst to cause nitrogen in the fuel and gaseous hydrogen to unite.

This produces ammonia and cleaner fuel.

This technology can reduce the nitrogen contained in both naturally

occurring and synthetic fuels.

Combustion Modification Combustion control uses one of the following

strategies: Reduce peak temperatures of the flame zone. The methods are :

increase the rate of flame cooling decrease the adiabatic flame temperature by dilution

Reduce residence time in the flame zone. For this we, change the shape of the flame zone

Reduce Oxygen concentration in the flame one. This can be accomplished by:

decreasing the excess air controlled mixing of fuel and air using a fuel rich primary flame zone

Modification Of Operating Conditions

The operating conditions can be modified to achieve significant reductions in the rate of thermal NOx production. the various methods are: (reduce NOx) Low-excess firing Off-stoichiometric combustion ( staged combustion ) Flue gas recirculation Reduced air preheat Reduced firing rates

Water Injection

Tail-end Control Processes o Combustion modification and modification of

operating conditions provide significant reductions in NOx, but not enough to meet regulations.

For further reduction in emissions, tail-end control equipment is required.

Some of the control processes are:

Selective Catalytic Reduction Selective Non-catalytic Reduction Electron Beam Radiation Staged Combustion

Selective Catalytic Reduction (SCR)

Schematic process flow diagram – NOX control

Selective Catalytic Reduction (SCR)

In this process, the nitrogen oxides in the flue gases are reduced to

nitrogen

During this process, only the NOx species are reduced

NH3 is used as a reducing gas

The catalyst is a combination of titanium and vanadium oxides. The

reactions are given below :

4 NO + 4 NH3 + O2 -----> 4N2 + 6H2O

2NO2 + 4 NH3+ O2 -----> 3N2 + 6H2O

Selective catalytic reduction catalyst is best at around 300 too 400 oC.

Typical efficiencies are around 80 %

Catalytic Combustion

Catalytic Emission Control

Electron Beam Radiation This treatment process is under development,

and is not widely used. Work is underway to determine the feasibility of electron beam radiation for neutralizing hazardous wastes and air toxics.

Irradiation of flue gases containing NOx or SOx produce nitrate and sulfate ions.

The addition of water and ammonia produces NH4NO3, and (NH4)2SO4

The solids are removed from the gas, and are sold as fertilizers.

Staged Combustion PRINCIPLE

Initially, less air is supplied to bring about incomplete combustion

Nitrogen is not oxidized. Carbon particles and CO are released.

In the second stage, more air is supplied to complete the combustion of carbon and carbon monoxide.

30% to 50% reductions in NOx emissions are achieved.

Staged Combustion

CARBON MONOXIDE CONTROL

Formation Of Carbon Monoxide

Due to insufficient oxygen

Factors affecting Carbon monoxide formation: Fuel-air ratio

Degree of mixing

Temperature

General Methods For Control of CO Emissions

Control carbon monoxide formation. Note : CO & NOx control strategies are in conflict.

Stationary Sources Proper Design Installation Operation Maintenance

Process Industries Burn in furnaces or waste heat boilers.

CARBON DIOXIDE CONTROL

Sources of Carbon DioxideHuman-Related Sources Combustion of fossil fuels: Coal, Oil, and Natural

Gas in power plants, automobiles, and industrial facilities

Use of petroleum-based products Industrial processes: Iron and steel production,

cement, lime, and aluminum manufactures

Natural Sources Volcanic eruptions Ocean-atmosphere exchange Plant photosynthesis

Sources of CO2 Emissions in the U.S.

Source: USEPA

(x-axis units are teragrams of CO2 equivalent)

CO2 Emissions from Fossil Fuel Combustion by Sector and Fuel Type

Source: USEPA

(y-axis units are teragrams of CO2 equivalent)

General Methods For Control of CO2 Emissions

Reducing energy consumption, increasing the efficiency of energy conversion

Switching to less carbon intensive fuels

Increasing the use of renewable sources

Sequestering CO2 through biological, chemical, or physical processes

CONTROL OF MERCURY EMISSIONS

Mercury Emissions Mercury exists in trace amounts in

Fossil fuels such as Coal, Oil, and Natural GasVegetationWaste products

Mercury is released to the atmosphere through combustion or natural processes

It creates both human and environmental risks Fish consumption is the primary pathway for human

and wildlife exposure United states is the first country in the world to

regulate mercury emissions from coal-fired power plants (March 15, 2005).

Source: Seingeur, 2004 and Mason and Sheu, 2002.

Source: Presentation by J. Pacyna and J. Munthe at mercury workshop in Brussels, March 29-30, 2004

Types of Sources

Worldwide Distribution of Emissions

Control Technologies for Mercury Emissions

Currently installed control devices for SO2, NOX, and particulates, in a power plant, remove some of the mercury before releasing from the stack

Activated Carbon Injection: Particles of activated carbon are injected into the exit gas flow, downstream

of the boiler. The mercury attaches to the carbon particles and is removed in a particle control device

Thief process for the removal of mercury from flue gas:It is a process which extracts partially burned coal from a pulverized coal-

fired combustor using a suction pipe, or "thief," and injects the resulting sorbent into the flue gas to capture the mercury.

PARTICULATE MATTER CONTROL

General Methods For Control Of Particulate Emissions

Five Basic Types of Dust Collectors :

Gravity and Momentum collectors Settling chambers, louvers, baffle chambers

Centrifugal Collectors Cyclones Mechanical centrifugal collectors

Fabric Filters Baghouses Fabric collectors

General Methods For Control Of Particulate Emissions (Contd.)

Electrostatic Precipitators Tubular Plate Wet Dry

Wet Collectors Spray towers Impingement scrubbers Wet cyclones Peaked towers Mobile bed scrubbers

General Methods For Control Of Particulate Emissions

Five Basic Types of Dust Collectors :

Gravity and Momentum collectors Settling chambers, louvers, baffle chambers

Centrifugal Collectors Cyclones Mechanical centrifugal collectors

Fabric Filters Baghouses Fabric collectors

Particulate Collection Mechanism

Gravity Settling

Centrifugal Impaction

Inertial Impaction

Direct Interception

Diffusion

Electrostatic Effects

Industrial Sources of Particulate Emissions Iron & Steel Mills, the blast furnaces, steel making furnaces. Petroleum Refineries, the catalyst regenerators, air-blown asphalt

stills, and sludge burners. Portland cement industry Asphalt batching plants Production of sulfuric acid Production of phosphoric acid Soap and Synthetic detergent manufacturing Glass & glass fiber industry Instant coffee plants

Effects  of  Particulate  Emissions Primary Effects • Reduction of visibility

• size distribution and refractive index of the particles • direct absorption of light by particles • direct light scattering by particles • 150 micro g / m3 concentration ~ average visibility of 5 miles

( satisfactory for air and ground transportation )

• Soiling of nuisance• increase cost of building maintenance, cleaning of furnishings,

and households • threshold limit is 200 - 250 micro g / m3 ( dust ) • levels of 400 - 500 micro g / m3 considered as nuisance

Cyclones

Principle • The particles are removed by the application of a centrifugal

force. The polluted gas stream is forced into a vortex. the motion of the gas exerts a centrifugal force on the particles, and they get deposited on the inner surface of the cyclones

• centrifugal force to capture, recover or remove large and high-volume dust from industrial applications.

Overall collection ηCi inlet concentration

Co outlet concentration

Cyclones (contd.)Construction and Operation

The gas enters through the inlet, and is forced into a spiral. • At the bottom, the gas reverses direction and flows upwards.

• To prevent particles in the incoming stream from contaminating the clean gas, a vortex finder is provided to separate them. the cleaned gas flows out through the vortex finder.

Cyclones (contd.) Advantages of Cyclones

• Cyclones have a lost capital cost • Reasonable high efficiency for specially designed cyclones. • They can be used under almost any operating condition. • Cyclones can be constructed of a wide variety of materials. • There are no moving parts, so there are no maintenance

requirements.

Disadvantages of Cyclones • They can be used for small particles • High pressure drops contribute to increased costs of operation.

Fabric Filters Principle

The filters retain particles larger than the mesh size

Air and most of the smaller particles flow through. Some of the smaller particles are retained due to interception and diffusion.

The retained particles cause a reduction in the mesh size.

The primary collection is on the layer of previously deposited particles.

Design of Fabric Filters The equation for fabric filters is based on

Darcy’s law for flow through porous media. Fabric filtration can be represented by the

following equation:S = Ke + KswWhere,S = filter drag, N-min/m3

Ke = extrapolated clean filter drag, N-min/m3

Ks = slope constant. Varies with the dust, gas and fabric, N-min/kg-mW= Areal dust density = LVt, where L = dust loading (g/m3), V = velocity (m/s)

Both Ke and Ks are determined empirically from pilot tests.

Fabric Filters

Δ P Total pressure drop

Δ Pf Pressure drop due to the fabric

Δ Pp Pressure drop due to the particulate layer

Δ Ps Pressure drop due to the bag house structure

Advantages of Fabric Filters Very high collection efficiency

They can operate over a wide range of volumetric flow rates

The pressure drops are reasonably low.

Fabric Filter houses are modular in design, and can be pre-assembled at the factory

Fabric Filters (contd.) Disadvantages of Fabric Filters

Fabric Filters require a large floor area.

The fabric is damaged at high temperature.

Ordinary fabrics cannot handle corrosive gases.

Fabric Filters cannot handle moist gas streams

A fabric filtration unit is a potential fire hazard

ΔPfPressure drop N/m2

ΔPp Pressure drop N/m2

Df Depth of filter in the direction of flow (m)

Dp Depth of particulate layer in the direction of flow (m)

μ Gas viscosity kg/m-sV superficial filtering velocity m/minKf, Kp Permeability (filter & particulate layer m2)

60 Conversion factor δ/minV = Q/A

Q volumetric gas flow rate m3/minA cloth area m2

Darcy’s equation

L Dust loading kg/m3

t time of operation minρL Bulk density of the particulate layer kg/m3

ΔP = ΔPf + ΔPp

Filter Drag S = ΔP/VAreal dust density W = LVtS= k1+k2W

Dust Layer

Electrostatic Precipitator Principle

The particles in a polluted gas stream are charged by passing them through an electric field.

The charged particles are led through collector plates The collector plates carry charges opposite to that on the particles The particles are attracted to these collector plates and are thus removed from

the gas steam

Construction and Operation of Electrostatic Precipitator Charging Electrodes in the form of thin wires are placed in the path of the

influent gas. The charging electrodes generate a strong electric field, which charges the

particles as they flow through it. The collector plates get deposited with the particles. the particles are

occasionally removed either by rapping or by washing the collector plates.

Design of Electrostatic Precipitators The efficiency of removal of particles by an

Electrostatic Precipitator is given by

η = fractional collection efficiency

w = drift velocity, m/min.A = available collection area, m2

Q = volumetric flow rate m3/min

Migration velocity

Where, q = charge (columbos)

Ep = collection field intensity (volts/m)r = particle radius (m)μ = dynamic viscosity of gas (Pa-S)c = cunningham correction factor

Cunningham correction factor

where,T = absolute temperature (°k)dp = diameter of particle (μm)

ELECTROSTATIC PRECIPITATOR (contd.) Advantages of Electrostatic Precipitators

Electrostatic precipitators are capable very high efficiency, generally of the order of 99.5-99.9%.

Since the electrostatic precipitators act on the particles and not on the air, they can handle higher loads with lower pressure drops.

They can operate at higher temperatures. The operating costs are generally low.

Disadvantages of Electrostatic Precipitators The initial capital costs are high. Although they can be designed for a variety of operating

conditions, they are not very flexible to changes in the operating conditions, once installed.

Particulate with high resistivity may go uncollected.

Wet Scrubbers Principle

Wet scrubbers are used for removal of particles which have a diameter of the order of 0.2 mm or higher.

Wet scrubbers work by spraying a stream of fine liquid droplets on the incoming stream.

The droplets capture the particles The liquid is subsequently removed for treatment.

Construction and Operation A wet scrubber consists of a rectangular or circular chamber in

which nozzles are mounted. The nozzles spray a stream of droplets on the incoming gas stream The droplets contact the particulate matter, and the particles get

sorbed. The droplet size has to be optimized.

Wet Scrubbers (contd.)o Construction and Operation (contd.)

Smaller droplets provide better cleaning, but are more difficult to remove from the cleaned stream.

The polluted spray is collected. Particles are settled out or otherwise removed from the liquid. The liquid is recycled. Wet scrubbers are also used for the removal of gases from the air

streams.

Scrubber Efficiency

where,k = Scrubber coefficient (m3 of gas/ m3 of liquid)R = Liquid-to-gas flow rate (QL/QG)ψ = internal impaction parameter

Internal impaction parameter

where,c = cunningham correction factorρp = particle density (kg/m3)Vg = speed of gas at throat (m/sec)dp = diameter of particle (m)

dd = diameter of droplet (m)μ = dynamic viscosity of gas, (Pa-S)

Wet Scrubbers (contd.) Advantages of Wet Scrubbers

Wet Scrubbers can handle incoming streams at high temperature, thus

removing the need for temperature control equipment. Wet scrubbers can handle high particle loading. Loading fluctuations do not affect the removal efficiency. They can handle explosive gases with little risk. Gas adsorption and dust collection are handled in one unit. Corrosive gases and dusts are neutralized.

Disadvantages of Wet Scrubbers High potential for corrosive problems Effluent scrubbing liquid poses a water pollution problem.

Cyclone Spray Chambers These scrubbers combine a cyclone with a spray

nozzle.

The added centrifugal force permits good

separation of the droplets, hence a smaller droplet

size can be used.

Cyclone spray chambers provide up to 95% removal

of particles > 5 micron.

Orifice Scrubbers The gas is impacted onto a layer of the scrubbing

liquid.

The gas passes through the liquid, thus removing

almost all the particulate matter, and a large

portion of the probable gases. After coming out of the liquid, the gas is passed

through baffles to remove the liquid droplets.

Impingement Scrubbers In Impingement scrubbers, the gas impacts a layer

of liquid/froth through a perforated tray.

Passing through this layer removes the particulate

matter.

The wet gas stream is then passed through a mist

collector.

Venturi Scrubbers The dirty gas is led in to the chamber at high inlet

velocities. At the inlet throat, liquid at low pressure is added

to the gas stream This increases the relative velocity between the gas

and the droplets, thus increasing the efficiency of removal.

Efficiencies of the range of 95% for particles larger than 0.2 mm have been obtained.

Venturi ScrubberAbsolute Pressure Drop

Δp = pressure drop ( cm of water)ug = gas velocity (cm/s)

Qt = liquid volume flow rate

Qg = gas volume flow rate

HYDROCARBON CONTROL

General Methods For Control Of Hydrocarbon Emissions

Incineration or after burning

Direct flame incineration

Thermal incineration

Catalytic incineration

VOC Incinerators Principle

VOC incinerators thermally oxidize the effluent stream, in the presence of excess air.

The complete oxidation of the VOC results in the formation of carbon monoxide and water. The reaction proceeds as follows:

CxHy + ( x + y/4 ) O2 x CO2 + (y/2) H2O Operation

The most important parameters in the design and operation of an incineration system are what are called the ' three T's ' Temperature, Turbulence, and residence Time.

VOC Incinerators (contd.) Temperature

The reaction kinetics are very sensitive to temperature The higher the temperature, the faster the reaction

o Timing A certain time has to be provided for the reaction to proceed

o Turbulence

Turbulence promotes mixing between the VOC's and oxygen Proper mixing helps the reaction to proceed to completion in the

given time.

VOC Incinerators (contd.) The various methods for incineration are:

Elevated fires, for concentrated streams

Direct thermal oxidation, for dilute streams

Catalytic oxidation, for dilute streams.

Xi volume of i component in the mixture

Xm volume of mixture

LELi LEL of i component

GASES

Air Pollution Control For Gases

Adsorption Towers

Thermal Incernation

Catalytic Combustion

Adsorption Towers Principle

Adsorption towers use adsorbents to remove the impurities

from the gas stream.

The impurities bind either physically or chemically to the

adsorbing material.

The impurities can be recovered by regenerating the adsorbent.

Adsorption towers can remove low concentrations of impurities

from the flue gas stream.

Adsorption Towers (contd.) Construction and Operation

Adsorption towers consist of cylinders packed with the adsorbent. The adsorbent is supported on a heavy screen Since adsorption is temperature dependent, the flue gas is

temperature conditioned. Vapor monitors are provided to detect for large concentrations in the

effluent. Large concentrations of the pollutant in the effluent indicate that the adsorbent needs to be regenerated.

Advantages of Adsorption Towers Very low concentrations of pollutants can be removed. Energy consumption is low. Do not need much maintenance. Economically valuable material can be recovered during regeneration.

Adsorption Towers (contd.) Disadvantages of adsorption Towers

Operation is not continuous.

They can only be used for specific pollutants.

Extensive temperature pre-conditioning equipment to be

installed.

Despite regeneration, the capacity of the adsorbent decreases

with use.

The End!!!