Date post: | 31-Dec-2015 |
Category: |
Documents |
Upload: | titania-lyris |
View: | 67 times |
Download: | 7 times |
Chapter 6 - 1
ISSUES TO ADDRESS...
• How does diffusion occur?
• Why is it an important part of processing?
• How can the rate of diffusion be predicted for some simple cases?
• How does diffusion depend on structure and temperature?
Chapter 6: Diffusion
Chapter 6 - 2
Diffusion
Diffusion - Mass transport by atomic motion
Mechanisms• Gases & Liquids – random (Brownian) motion• Solids – vacancy diffusion or interstitial diffusion
Chapter 6 - 3
• Interdiffusion: In an alloy, atoms tend to migrate from regions of high conc. to regions of low conc.
Initially
Adapted from Figs. 6.1 and 6.2, Callister & Rethwisch 4e.
Diffusion
After some time
Chapter 6 - 4
• Self-diffusion: In an elemental solid, atoms also migrate.
Label some atoms
Diffusion
A
B
C
D
After some time
A
B
C
D
Chapter 6 - 5
Diffusion Mechanisms
Vacancy Diffusion:
• atoms exchange with vacancies • applies to substitutional impurities atoms • rate depends on: -- number of vacancies -- activation energy to exchange.
increasing elapsed time
Chapter 6 - 6
• Simulation of interdiffusion across an interface:
• Rate of substitutional diffusion depends on: -- vacancy concentration -- frequency of jumping
(Courtesy P.M. Anderson)
Diffusion SimulationThis slide contains an animation that requires Quicktime and a Cinepak decompressor. Click on the message or image below to activate the animation.
Chapter 6 - 7
Diffusion Mechanisms
• Interstitial diffusion – smaller atoms can diffuse between atoms.
More rapid than vacancy diffusionAdapted from Fig. 6.3 (b), Callister & Rethwisch 4e.
Chapter 6 - 8
Adapted from chapter-opening photograph, Chapter 6, Callister & Rethwisch 4e. (Courtesy ofSurface Division, Midland-Ross.)
• Case Hardening: -- Diffuse carbon atoms into the host iron atoms at the surface. -- Example of interstitial diffusion is a case hardened gear.
• Result: The presence of C atoms makes iron (steel) harder.
Processing Using Diffusion
Chapter 6 - 9
• Doping silicon with phosphorus for n-type semiconductors:• Process:
3. Result: Doped semiconductor regions.
silicon
Processing Using Diffusion
magnified image of a computer chip
0.5 mm
light regions: Si atoms
light regions: Al atoms
2. Heat it.
1. Deposit P rich layers on surface.
silicon
Adapted from Figure 12.27, Callister & Rethwisch 4e.
Chapter 6 - 10
Diffusion• How do we quantify the amount or rate of diffusion?
J slopeM =
massdiffused
time
• Measured empirically– Make thin film (membrane) of known cross-sectional area– Impose concentration gradient– Measure how fast atoms or molecules diffuse through the
membrane
Chapter 6 - 11
Steady-State Diffusion
Fick’s first law of diffusionC1
C2
x
C1
C2
x1 x2
D diffusion coefficient
Rate of diffusion independent of time
Flux proportional to concentration gradient =
Chapter 6 - 12
Example: Chemical Protective Clothing (CPC)
• Methylene chloride is a common ingredient of paint removers. Besides being an irritant, it also may be absorbed through skin. When using this paint remover, protective gloves should be worn.
• If butyl rubber gloves (0.04 cm thick) are used, what is the diffusive flux of methylene chloride through the glove?
• Data:– diffusion coefficient in butyl rubber:
D = 110 x10-8 cm2/s– surface concentrations:
C2 = 0.02 g/cm3
C1 = 0.44 g/cm3
Chapter 6 - 13
Example (cont).
gloveC1
C2
skinpaintremover
x1 x2
• Solution – assuming linear conc. gradient
D = 110 x 10-8 cm2/s
C2 = 0.02 g/cm3
C1 = 0.44 g/cm3
x2 – x1 = 0.04 cm
Data:
Chapter 6 - 14
Diffusion and Temperature
• Diffusion coefficient increases with increasing T
D=Do exp æ
è ç
ö
ø-
Qd
RT
= pre-exponential [m2/s]
= diffusion coefficient [m2/s]
= activation energy [J/mol or eV/atom]
= gas constant [8.314 J/mol-K]
= absolute temperature [K]
D
Do
Qd
R
T
Chapter 6 - 15
Diffusion and Temperature
Adapted from Fig. 6.7, Callister & Rethwisch 4e. (Date for Fig. 6.7 taken from E.A. Brandes and G.B. Brook (Ed.) Smithells Metals Reference Book, 7th ed., Butterworth-Heinemann, Oxford, 1992.)
D has exponential dependence on T
Dinterstitial >> Dsubstitutional
C in a-FeC in g-Fe
Al in AlFe in a-FeFe in g-Fe
1000 K/T
D (m2/s) C in a-Fe
C in g-Fe
Al in Al
Fe in a-Fe
Fe in g-Fe
0.5 1.0 1.510-20
10-14
10-8
T(C)15
00
1000
600
300
Chapter 6 - 16
Example: At 300ºC the diffusion coefficient and activation energy for Cu in Si are
D(300ºC) = 7.8 x 10-11 m2/sQd = 41.5 kJ/mol
What is the diffusion coefficient at 350ºC?
transform data
D
Temp = T
ln D
1/T
Chapter 6 - 17
Example (cont.)
T1 = 273 + 300 = 573 K
T2 = 273 + 350 = 623 K
D2 = 15.7 x 10-11 m2/s
Chapter 6 - 18
Non-steady State Diffusion
• The concentration of diffusing species is a function of both time and position C = C(x,t)
• In this case Fick’s Second Law is used
Fick’s Second Law
Chapter 6 -
VMSE: Screenshot of Diffusion Computations & Data Plots
19
Chapter 6 - 20
Non-steady State Diffusion
Adapted from Fig. 6.5, Callister & Rethwisch 4e.
B.C. at t = 0, C = Co for 0 x
at t > 0, C = CS for x = 0 (constant surface conc.)
C = Co for x =
• Copper diffuses into a bar of aluminum.
pre-existing conc., Co of copper atoms
Surface conc., C of Cu atoms bar
s
Cs
Chapter 6 - 21
Solution:
C(x,t) = Conc. at point x at time t
erf (z) = error function
erf(z) values are given in Table 6.1
CS
Co
C(x,t)
Adapted from Fig. 6.5, Callister & Rethwisch 4e.
Chapter 6 - 22
Non-steady State Diffusion
• Sample Problem: An FCC iron-carbon alloy initially containing 0.20 wt% C is carburized at an elevated temperature and in an atmosphere that gives a surface carbon concentration constant at 1.0 wt%. If after 49.5 h the concentration of carbon is 0.35 wt% at a position 4.0 mm below the surface, determine the temperature at which the treatment was carried out.
• Solution: use Eqn. 6.5
Chapter 6 - 23
Solution (cont.):
– t = 49.5 h x = 4 x 10-3 m– Cx = 0.35 wt% Cs = 1.0 wt%
– Co = 0.20 wt%
erf(z) = 0.8125
Chapter 6 - 24
Solution (cont.):
We must now determine from Table 6.1 the value of z for which the error function is 0.8125. An interpolation is necessary as follows
z erf(z)
0.90 0.7970z 0.81250.95 0.8209
z = 0.93
Now solve for D
Chapter 6 - 25
• To solve for the temperature at which D has the above value, we use a rearranged form of Equation (6.9a);
from Table 6.2, for diffusion of C in FCC Fe
Do = 2.3 x 10-5 m2/s Qd = 148,000 J/mol
Solution (cont.):
T = 1300 K = 1027°C
Chapter 6 - 26
Example: Chemical Protective Clothing (CPC)
• Methylene chloride is a common ingredient of paint removers. Besides being an irritant, it also may be absorbed through skin. When using this paint remover, protective gloves should be worn.
• If butyl rubber gloves (0.04 cm thick) are used, what is the breakthrough time (tb), i.e., how long could the gloves be used before methylene chloride reaches the hand?
• Data– diffusion coefficient in butyl rubber:
D = 110 x10-8 cm2/s
Chapter 6 - 27
CPC Example (cont.)
Time required for breakthrough ca. 4 min
gloveC1
C2
skinpaintremover
x1 x2
• Solution – assuming linear conc. gradient
Equation from online CPC Case Study 5 at the Student Companion Site for Callister & Rethwisch 4e (www.wiley.com/college/callister)
D = 110 x 10-8 cm2/s
Breakthrough time = tb
Chapter 6 - 28
Diffusion FASTER for...
• open crystal structures
• materials w/secondary bonding
• smaller diffusing atoms
• lower density materials
Diffusion SLOWER for...
• close-packed structures
• materials w/covalent bonding
• larger diffusing atoms
• higher density materials
Summary
Chapter 6 - 29
Core Problems:
Self-help Problems:
ANNOUNCEMENTS
Reading: