Checking Rules

WCDMA RAN and I-HSPA, Rel. RU30, Operating Documentation, Issue 04

WCDMA RAN and I-HSPA RNW Consistency Checking Rules

DN0934038

Issue 02DApproval Date 2011-09-14

Confidential

2 DN0934038Issue 02D

WCDMA RAN and I-HSPA RNW Consistency Check-ing Rules

Id:0900d805808b529dConfidential

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2011. All rights reserved

f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources of danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product.

The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.

The same text in German:

f Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen ausgehen.

Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-anforderungen erfolgen.

Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal, Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentations-satzes.

DN0934038 3



Table of contentsThis document has 106 pages.

Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2 ADJD consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3 ADJG consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4 ADJI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5 ADJL consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6 ADJS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

7 CBCI consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

8 CMOB consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

9 COCO consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

10 FMCG consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

11 FMCI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

12 FMCS consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

13 HOPG consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

14 HOPI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

15 HOPL consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

16 HOPS consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

17 IPNB consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

18 IPQM consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

19 IU consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

20 IUO consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

21 IUR consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

22 RNAC consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

23 RNC consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

24 RNFC consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

25 RNHSPA consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . 50

26 RNMOBI consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . 52

27 RNPS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

28 RNRLC consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

29 RNTRM consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

30 TQM consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

4 DN0934038



31 VBTS consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

32 VCEL consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

33 WANE consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

34 WBTS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

35 WCEL consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

36 WLCSE consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

37 WRAB consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

38 WSG consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

39 WSMLC consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . 104

DN0934038 5



List of tablesTable 1 Rule and description attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Table 2 ADJD consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Table 3 ADJG consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Table 4 ADJI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Table 5 ADJL consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Table 6 ADJS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Table 7 CBCI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Table 8 CMOB consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Table 9 COCO consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Table 10 FMCG consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Table 11 FMCI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Table 12 FMCS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Table 13 HOPG consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Table 14 HOPI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Table 15 HOPL consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Table 16 HOPS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Table 17 IPNB consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Table 18 IPQM consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Table 19 IU consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Table 20 IUO consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Table 21 IUR consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Table 22 RNAC consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Table 23 RNC consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Table 24 RNFC consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Table 25 RNHSPA consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . 50Table 26 RNMOBI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . 52Table 27 RNPS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Table 28 RNRLC consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Table 29 RNTRM consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Table 30 TQM consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Table 31 VBTS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Table 32 VCEL consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Table 33 WANE consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Table 34 WBTS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Table 35 WCEL consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Table 36 WLCSE consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . 101Table 37 WRAB consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 102Table 38 WSG consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103Table 39 WSMLC consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . 104

6 DN0934038


Id:0900d805808b8255Confidential

Summary of changes

Summary of changes Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.

Note that the issue numbering system and product naming practices are changing. For more information, see Guide to WCDMA RAN and I-HSPA Operating Documentation.

Changes between issues 02C (2011-06-13, RU30) and 02D (2011-09-14, RU30)

General changes in this issue

• RNC refers to the IPA-RNC, mcRNC, and I-HSPA adapter collectively, when it is not necessary to specify them individually. The word controller is no longer used for this purpose.

Introduction (1)

• A redundant reference to the WCDMA RAN and I-HSPA system library has been removed.

• The word controller has been changed to RNC throughout this section.

WBTS consistency checking rules (34)

• Rules added: WBTS_CM_0048, WBTS_CM_0049, WBTS_CM_0050, WBTS_CM_0051, WBTS_M_0012, WBTS_M_0013, WBTS_M_0014

WCEL consistency checking rules (35)

• Rule added: WCEL_M_0028

Changes between issues 02B (2011-03-06, WCDMA RAN RU30) and 02C (2011-06-13, WCDMA RAN and I-HSPA RU30)

General changes in this issue

• This document has been updated to include information relevant to the IPA-RNC, mcRNC, and I-HSPA.

• The word controller refers to the IPA-RNC, mcRNC, and I-HSPA adapter, when it is not necessary to specify them individually.

Introduction (1)

• IPA-RNC/mcRNC/I-HSPA information added

ADJD consistency checking rules (2)

• Rule modified: ADJD_CM_0007

ADJI consistency checking rules (4)

• Rules modified: ADJI_CM_0006, ADJI_CM_0012, ADJI_CM_0013

• Rules removed: ADJI_CM_0014, ADJI_CM_0015

ADJS consistency checking rules (6)

• Rule modified: ADJS_CM_0008

• Rule removed: ADJS_CM_0016

DN0934038 7


Summary of changes


FMCG consistency checking rules (10)

• Rule added: FMCG_M_0002

FMCS consistency checking rules (12)

• Rule modified: FMCS_D_0002

IU consistency checking rules (19)

• Rule modified: IU_CM_0011

IUO consistency checking rules (20)

• Rules added: IUO_CM_0006, IUO_CM_0007, IUO_CM_0008, IUO_CM_0009, IUO_MD_0002

• Rules modified: IUO_CM_0001, IUO_CM_0002, IUO_CM_0003, IUO_CM_0004, IUO_CM_0005

RNAC consistency checking rules (22)

• New chapter resulting from the IPA-RNC object split. Rule added: RNAC_CM_0001

RNC consistency checking rules (23)

• Rule added: RNC_CM_0007

• Rule modified: RNC_CM_0038 has been renamed RNC_CM_0006.

RNFC consistency checking rules (24)

• Rule added: RNFC_M_0025

WBTS consistency checking rules (34)

• Rules added: WBTS_CM_0038, WBTS_CM_0039, WBTS_CM_0040, WBTS_CM_0041, WBTS_CM_0042, WBTS_CM_0043, WBTS_CM_0044, WBTS_CM_0045, WBTS_CM_0046, WBTS_CM_0047

WCEL consistency checking rules (35)

• Rules added: WCEL_CM_175, WCEL_CM_176

• Rules modified: WCEL_CM_0033, WCEL_M_0004

WLCSE consistency checking rules (36)

• Rule modified: WLCSE_C_0002

Changes between issues 02A (2010-12-08, WCDMA RAN RU30) and 02B (2011-03-06, WCDMA RAN RU30)

RNFC consistency checking rules (23) • Rules removed: RNFC_CM_0001, RNFC_CM_0002, RNFC_CM_0003,

RNFC_CM_0004, RNFC_CM_0005

WBTS consistency checking rules (33) • Rule removed: WBTS_M_0006

WCEL consistency checking rules (34) • Rules removed: WCEL_CM_0002, WCEL_CM_0029, WCEL_CM_0031,

WCEL_CM_0032, WCEL_CM_0068, WCEL_CM_0076, WCEL_CM_0097

8 DN0934038



Summary of changes

WSMLC consistency checking rules (38) • Rules modified: WSMLC_M_0001 has been renamed WSMLC_CM_0018.

WSMLC_M_0002 has been renamed WSMLC_CM_0019. • Rule removed: WSMLC_CM_0004

DN0934038 9


Introduction

Id:0900d805808be424Confidential

1 IntroductionThis document describes the consistency checks performed between the different radio network (RNW) configuration management parameters during operations targeted to RNW managed objects.

The RNW consistency check is a service provided by the RNC software (that is, the IPA-RNC/I-HSPA/mcRNC software) to ensure the consistency of the RNC database, which is configured for different RNW managed objects. The consistency checks are based on the defined relationships between the RNW configuration management parameters under the same or different RNW managed objects. In these checks, the parameter data are compared with each other to ensure that the data are consistent according to the parameter relationship definitions. The consistency checks are performed during RNW plan download, or during direct activation or GUI operations on the RNW managed objects. The same consistency rules apply to the configuration tasks carried out by the Parameter Editor application in the OMS Element Manager.

In contrast, the parameter range check is done by the RNC software (RAYMAN) during RNW parameter creation/modification, to ensure that the parameter value is within the valid range. This parameter range check is performed before the consistency check and thus it is not included in the consistency checking rules described in this document. For more information about the value ranges of the different RNW parameters, see WCDMA Radio Network Configuration Parameters.

Consistency checking rules are grouped according to managed objects in this docu-ment. Under the managed object, rules are arranged by the operation type and the rule identifier. Each rule has its own unique identifier, which consists of the managed object, the operation type, and the number. The number is unique within the managed object and the operation type.

The rules are presented in tables. The following table presents the attributes for each rule and a description of the attributes.

Entry Description

Checking rule identifier (ID) The unique identifier for the rule. The format is “ManagedObject_OperationType_FourDigitNumber”, for example, WBTS_C_0002. The following abbreviations are used for operation type:

• C (Creation) • CM (Creation and Modification) • M (Modification) • D (Deletion) • U (Unlock) (This is valid for WCEL only.)

RNW managed object type This attribute defines for which RNW managed object the rule is valid.

Operation type This attribute defines the operation for which the rule is valid and the consistency check is performed.

Check description This attribute defines the actual checking performed during the oper-ation.

Table 1 Rule and description attributes

10 DN0934038



Introduction

Error text This attribute defines the error text returned if the consistency check rule is not fulfilled.

Entry Description

Table 1 Rule and description attributes (Cont.)

DN0934038 11


ADJD consistency checking rules

Id:0900d80580891c5bConfidential

2 ADJD consistency checking rulesThe following table lists the ADJD consistency checking rules.

Checking rule identifier (ID)

Object type

Operation type

Check description Error text

ADJD_C_0001 ADJD Create ADJDId must be unique within the parent WCEL

ADJD ALREADY CREATED UNDER WCEL

ADJD_C_0002 ADJD Create The maximum amount of ADJD under the WCEL is 32

MAXIMUM OF ADJDS FOR WCEL

ADJD_CM_0001 ADJD Create/Modify AdjdRTHopsId and AdjdN-RTHopsId must refer to the existing HOPS object (Intra-frequency Handover Path)

HOPS NOT FOUND

ADJD_CM_0002 ADJD Create/Modify The scrambling code must be different between the ADJD and the source WCEL

ADJD AND SOURCE CELL MUST HAVE DIFFERENT PRIMARY SCRAMBLING CODE

ADJD_CM_0003 ADJD Create/Modify The same scrambling code is not allowed for other ADJD of the source WCEL

PRIMARY SCRAMBLING CODE MUST BE UNIQUE WITHIN ADJD OF THE SAME SOURCE CELL

ADJD_CM_0004 ADJD Create/Modify The same scrambling code is not allowed for any ADJS of the source WCEL

PRIMARY SCRAMBLING CODE OF AN ADJS AND AN ADJD OF THE SAME SOURCE WCEL MUST BE DIFFERENT

ADJD_CM_0005 ADJD Create/Modify ADJD must have a unique target WCEL among ADJDs under the source WCEL

THE SAME TARGET CELL IS POINTED BY AN ADJD OF THE SAME SOURCE CELL

ADJD_CM_0006 ADJD Create/Modify ADJD must have a different target WCEL from any ADJS under the source WCEL

THE SAME TARGET CELL IS POINTED BY AN ADJS OF THE SAME SOURCE CELL

ADJD_CM_0007 ADJD Create/Modify ADJD parameters LAC, RAC, SCRCODE, UEtxPowerMax-PRACH, UEtxPowerMaxD-PCH, PtxPrimaryCPICH, and UARFCN should be consistent with the corresponding param-eters defined in the target cell

ADJD PARAMETERS MCC,MNC,LAC,RAC,SCR-CODE,CPICHTXPWR MUST BE SAME IN TARGET WCEL AND ADJD.

ADJD_CM_0008 ADJD Create/Modify The UARFCN of the source and the target WCEL must be the same

SOURCE AND TARGET CELLS MUST HAVE SAME FREQUENCY IN ADJD

Table 2 ADJD consistency checking rules

12 DN0934038


Id:0900d80580891c5bConfidential

ADJD consistency checking rules

ADJD_CM_0009 ADJD Create/Modify When the source WCEL is HSDPA-enabled, AdjdHS-DPAHopsId must be defined

HSDPA HOPS ID MUST BE DEFINED FOR OUTGOING ADJD OF HSDPA ENABLED CELL

ADJD_CM_0010 ADJD Create/Modify When the source WCEL is HSDPA-enabled, and HSDPA with AMR is enabled in the RNC, AdjdRTWithHSDPA-HopsId must be defined

RT HSDPA HOPS MUST BE DEFINED FOR ADJD OF HSDPA ENABLED CELL IF RNC SUPPORTS AMRWITH-HSDSCH

ADJD_CM_0011 ADJD Create/Modify If AdjdHSDPAHopsId is defined, the referred HOPS must exist

HOPS NOT FOUND

ADJD_CM_0012 ADJD Create/Modify If AdjdRTWithHSDPAHopsId is defined, the referred HOPS must exist

HOPS NOT FOUND

ADJD_CM_0013 ADJD Create/Modify If the Cell is controlled by the local RNC, ADJD -ADJDTX-DIV cannot be modified

IF THE CELL IS CON-TROLLED BY THE LOCAL RNC, ADJD -ADJDTXDIV CAN NOT BE MODIFIED

ADJD_CM_0014 ADJD Create/Modify The option “Detected Set Reporting Based SHO” must be supported

ADJD CANNOT BE CREATED OR MODIFIED IF FEATURE STATE OF DETECT SET REPORTING BASED SHO OFF

ADJD_M_0001 ADJD Modify The parameters related to the target WCEL except AdjdRN-CId (AdjdMCC, AdjdMNC-Length, AdjdMNC, and AdjdCI) cannot be modified when the target cell is under the same RNC

TARGET CELL OF THE ADJACENCY IS NOT ALLOWED TO CHANGE IF TARGET CELL IS UNDER THE SAME RNC


Object type

Operation type


Table 2 ADJD consistency checking rules (Cont.)

DN0934038 13


ADJG consistency checking rules

Id:0900d805807e02a1Confidential

3 ADJG consistency checking rulesThe following table lists the ADJG consistency checking rules.


Object type

Operation type


ADJG_C_0001 ADJG Create ADJGId must be unique within the parent WCEL

ADJG ALREADY CREATED UNDER WCEL

ADJG_C_0002 ADJG Create The maximum amount of ADJG under the WCEL is 32

MAXIMUM OF ADJGS FOR WCEL

ADJG_C_0003 ADJG Create Each WCDMA cell can have only one GAN specific inter-RAT neighbor cell (ADJG).

EACH WCDMA CELL CAN HAVE ONLY ONE GAN SPECIFIC INTER-RAT NEIGHBOUR CELL (ADJG)

ADJG_CM_0001 ADJG Create/Modify BCCH and BSIC must be dif-ferent between separate ADJG definitions

BCCH AND BSIC MUST BE DIFFERENT BETWEEN SEPARATE ADJG DEFINI-TIONS

ADJG_CM_0002 ADJG Create/Modify ADJG with the same target WCEL must not exist

THERE IS ALREADY ANOTHER ADJ POINTING TO SAME TARGET UNDER THIS WCEL.

ADJG_CM_0003 ADJG Create/Modify If ADJGId is 0 and the parame-ter AMRDirReCell of the FMCG that the source WCEL points with RtFmcgIdentifier has the value Enabled, the value of AdjgSIB cannot be No, that is, the ADJG must be included in System Informa-tion.

ADJG-AdjgSIB SHOULD NOT BE SET AS 0 (NO) WHEN AMR CALL INTERSYSTEM HANDOVER IS ON

ADJG_CM_0004 ADJG Create/Modify If the ADJG is GAN-specific (BCCH and BSIC are the same as RNC parameters GANet-wARFCN, GANetwNCC, and GANetwBCC), AdjgSIB must be No, that is, GAN-specific ADJG cannot be included in System Information.

GAN ADJG CAN EXIST ONLY WHEN GSM NEIGHBOUR CELL IS NOT INCLUDED IN THE SYSTEM INFORMA-TION

ADJG_CM_0005 ADJG Create/Modify If the option “UTRAN - GAN interworking” is ON, and the option “GSM ISHO” is OFF, only the GAN-specific ADJG can be configured.

ADJG GAN RELATED PARAMETERS NOT SAME WITH RNC PARAMETERS GANetwARFCN, GANetwNCC AND GANetwBCC

Table 3 ADJG consistency checking rules

14 DN0934038



ADJG consistency checking rules

ADJG_CM_0006 ADJG Create/Modify Normal ADJG (not GAN spe-cific) – RtHopgIdentifier and NrtHopgIdentifier must refer to the existing HOPG object (Inter-system Handover Path)

HOPG NOT FOUND

ADJG_CM_0007 ADJG Create/Modify As for normal ADJG (not GAN specific), RT+NRT FMCG must be defined for the source WCEL

FMCG ID NOT DEFINED FOR THE WCEL

ADJG_CM_0008 ADJG Create/Modify If AdjgBandIndicator has the value 0, the full GSM band range 0~1023 is allowed; if AdjgBandIndicator has the value 1, only the GSM1900 band range is allowed.

ADJG BCCH ARFCN VALUE OUT OF RANGE

ADJG_CM_0009 ADJG Create/Modify When the ADJG is not GAN-specific, and the source WCEL is HSDPA enabled, the source cell’s HSDPAFmcgIdentifier must be defined

HSDPA FMCG MUST BE DEFINED IF HSDPA ENABLED AND ADJG(S) CREATED UNDER THE WCEL

ADJG_CM_0010 ADJG Create/Modify When the ADJG is not GAN-specific, the source WCEL is HSDPA-enabled, and HSDPA with AMR is enabled in the RNC, the source cell’s RTWithHSDPAFmcgIdentifier must be defined

RT HSDPA FMCG MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL

ADJG_CM_0011 ADJG Create/Modify If WireLessPriorityService in the RNC is Enabled, and ADJGId is 0, the value of AdjgSIB cannot be No, that is, the ADJG must be included in System Information.

ADJGSIB IS NOT ENABLED FOR WPS ADJG IN ONE OR MORE WCEL IN RNC RNW DATABASE

ADJG_M_0001 ADJG Modify ADJG - BandIndicator is not modifiable

BAND INDICATOR MAY NOT BE CHANGED


Object type

Operation type


Table 3 ADJG consistency checking rules (Cont.)

DN0934038 15


ADJI consistency checking rules

Id:0900d8058088fcf8Confidential

4 ADJI consistency checking rulesThe following table lists the ADJI consistency checking rules.


Object type

Operation type


ADJI_C_0001 ADJI Create ADJIId must be unique within the parent WCEL

ADJI ALREADY CREATED UNDER WCEL

ADJI_C_0002 ADJI Create The maximum amount of ADJI under the WCEL is 48

MAXIMUM OF ADJIS FOR WCEL

ADJI_CM_0001 ADJI Create/Modify The maximum number of inter-frequency neighbor cells that can be included in the System Information is 32.

MAXIMUM NUMBER OF ADJIS INCLUDED IN BCCH INFOEXCEEDED

ADJI_CM_0002 ADJI Create/Modify ADJI – RtHopiIdentifier and NrtHopiIdentifier must refer to an existing HOPI object (Inter-system Handover Path)

HOPI NOT FOUND

ADJI_CM_0003 ADJI Create/Modify The UARFCN of the source WCEL and ADJI must be dif-ferent (WCEL – UARFCN, ADJI - AdjiUARFCN)

ADJI AND ITS SOURCE WCEL MUST HAVE DIFFER-ENT FREQS

ADJI_CM_0004 ADJI Create/Modify The scrambling code and UARFCN combination must be unique within the ADJI objects under the same source WCEL

PRI SCRC AND UARFCN COMBINATION OF AN INTER-FREQ NEIGHBOUR CELL MUST BE UNIQUE WITHIN ADJI

ADJI_CM_0005 ADJI Create/Modify ADJI with the same target WCEL must not exist

THERE IS ALREADY ANOTHER ADJ POINTING TO SAME TARGET UNDER THIS WCEL.

ADJI_CM_0006 ADJI Create/Modify ADJI parameters LAC, RAC, SCRCODE, UEtxPowerMax-PRACH, UEtxPowerMaxD-PCH, PtxPrimaryCPICH, and UARFCN should be consistent with the corresponding param-eters defined in the target cell.

LAC,RAC,SCRCODE,UETX-POWERMAXPRACH,UETX-POWERMAXDPCH,PTXPRIMARYCPICH,UARFCN MUST BE SAME IN TGT WCEL AND ADJI

ADJI_CM_0007 ADJI Create/Modify RT+NRT FMCI must be defined for the source WCEL

FMCI ID NOT DEFINED FOR THE WCEL

ADJI_CM_0008 ADJI Create/Modify When the source WCEL is HSDPA-enabled, the source cell’s HSDPAFmciIdentifier must be defined

HSDPA FMCI MUST BE DEFINED IF HSDPA ENABLED AND ADJI(S) CREATED UNDER THE WCEL

Table 4 ADJI consistency checking rules

16 DN0934038


Id:0900d8058088fcf8Confidential

ADJI consistency checking rules

ADJI_CM_0009 ADJI Create/Modify When the source WCEL is HSDPA enabled and HSDPA with AMR is enabled in the RNC, the source cell’s RTWithHSDPAFmciIdentifier must be defined

RT HSDPA FMCI MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL

ADJI_CM_0010 ADJI Create/Modify When the source WCEL is HSDPA enabled and HSDPA with AMR is enabled in the RNC, the source cell’s RTWithHSDPAFmciIdentifier must be defined


ADJI_CM_0011 ADJI Create/Modify ADJI-AdjiTxDiv must be set to zero if the inter-frequency neighbor cell is controlled by the local RNC.

IF THE INTER-FREQUENCY NEIGHBOR CELL IS CON-TROLLED BY THE LOCAL RNC, ADJI-ADJITXDIV MUST BE SET TO ZERO

ADJI_CM_0012 ADJI Create/Modify Multiple ADJIs under a single WCEL having the same ADJI-UARFCN should not have BlindHoTargetCell as enabled.

MULTIPLE ADJI UNDER A SINGLE WCEL HAVING THE SAME ADJIUARFCN SHOULD NOT HAVE BLIND-HOTARGETCELL AS ENABLED

ADJI_CM_0013 ADJI Create/Modify ADJI-BlindHOTargetCell must be enabled only when neighbor cell RNC id AdjiRN-Cid is same as this cell RNCid

ADJI-BLINDHOTARGET-CELL MUST BE ENABLED ONLY WHEN NEIGHBOUR CELL RNC ID ADJIRNCID IS SAME AS THIS CELL RNCID

ADJI_M_0001 ADJI Modify The parameters related to the target cell except AdjiRNCid (AdjiMCC, AdjiMNCLength, AdjiMNC, and AdjiCI) cannot be modified when the target cell is under the own RNC


ADJI_M_0003 ADJI Modify ADJI-AdjiUARFCN is not mod-ifiable if target cell is under own RNC

ADJI-ADJIUARFCN IS NOT MODIFIABLE IF TARGET CELL IS UNDER OWN RNC


Object type

Operation type


Table 4 ADJI consistency checking rules (Cont.)

DN0934038 17


ADJL consistency checking rules

Id:0900d80580827662Confidential

5 ADJL consistency checking rulesThe following table lists the ADJL consistency checking rules.


Object type

Operation type


ADJL_CM_0001 ADJL Create/Modify AbsPrioCellReselec and AdjLAbsPrioCellReselec always have unique values

ABSPRIOCELLRESELEC AND ADJLABSPRIOCELLRE-SELEC ALWAYS HAVE UNIQUE VALUES

ADJL_CM_0002 ADJL Create/Modify Maximum of ADJLs for WCEL MAXIMUM OF ADJLs FOR WCEL

Table 5 ADJL consistency checking rules

18 DN0934038


Id:0900d805808902e1Confidential

ADJS consistency checking rules

6 ADJS consistency checking rulesThe following table lists the ADJS consistency checking rules.


Object type

Operation type


ADJS_C_0001 ADJS Create ADJSId must be unique within the parent WCEL

ADJS ALREADY CREATED UNDER WCEL

ADJS_C_0002 ADJS Create The maximum number of ADJS under the WCEL is 31

MAXIMUM OF ADJSS FOR WCEL

ADJS_CD_0001 ADJS Create/Delete UARFCN of the source and target WCEL must be the same

SOURCE AND TARGET WCELS MUST HAVE SAME FREQS IN ADJS (INTRA-FREQ ADJ)

ADJS_CM_0001 ADJS Create/Modify If RTWithHSDPAHopsIdenti-fier is defined, the referred HOPS must exist

HOPS NOT FOUND

ADJS_CM_0002 ADJS Create/Modify ADJS – RtHopsIdentifier and NrtHopsIdentifier must refer to the existing HOPS object (Intra-frequency Handover Path)

HOPS NOT FOUND

ADJS_CM_0003 ADJS Create/Modify The scrambling code must be different between the ADJS and the source WCEL

ADJS (INTRA-FREQ ADJ) AND SOURCE WCEL MUST HAVE DIFFERENT DL_PRI_SCR_CODE

ADJS_CM_0004 ADJS Create/Modify The same scrambling code is not allowed for other ADJS of the source WCEL

PRIMARY SCRAMBLING CODE OF AN INTRA-FRE-QUENCY NEIGHBOUR CELL MUST BE UNIQUE WITHIN ADJS.

ADJS_CM_0005 ADJS Create/Modify The same scrambling code is not allowed for any ADJD of the source WCEL

PRIMARY SCRAMBLING CODE OF AN ADJS AND AN ADJD OF THE SAME SOURCE WCEL MUST BE DIFFERENT

ADJS_CM_0006 ADJS Create/Modify ADJS must have a unique target WCEL among ADJSs under the source WCEL

THE SAME TARGET CELL IS POINTED BY AN ADJS OF THE SAME SOURCE CELL

ADJS_CM_0007 ADJS Create/Modify ADJS must have a different target WCEL from any ADJD under the source WCEL

THE SAME TARGET CELL IS POINTED BY AN ADJD OF THE SAME SOURCE CELL

Table 6 ADJS consistency checking rules

DN0934038 19


ADJS consistency checking rules


ADJS_CM_0008 ADJS Create/Modify ADJS parameters LAC, RAC, SCRCODE, UEtxPowerMax-PRACH, and PtxPrimary-CPICH should be consistent with the corresponding param-eters defined in the target cell.

LAC,RAC,SCRCODE,UETX-POWERMAX-PRACH,PTXPRIMARYCPICH MUST BE SAME IN TGT WCEL AND ADJS

ADJS_CM_0009 ADJS Create/Modify If HSDPAHopsIdentifier is defined, the referred HOPS should exist

HOPS NOT FOUND

ADJS_CM_0010 ADJS Create/Modify When the source WCEL is HSDPA enabled and HSDPA with AMR is enabled in the RNC, RTWithHSDPAHopsI-dentifier must be defined

HSDPA HOPS FOR AMR MULTI-SERVICE MUST BE DEFINED FOR THE SOURCE WCEL

ADJS_CM_0011 ADJS Create/Modify If RTWithHSDPAHopsIdenti-fier is defined, the referred HOPS should exist

HOPS NOT FOUND

ADJS_CM_0012 ADJS Create/Modify If the intra-frequency neighbor cell is controlled by the local RNC, ADJS-AdjsTxDiv must be set to zero

If the intra-frequency neighbor cell is controlled by the local RNC, ADJS-AdjsTxDiv must be set to zero

ADJS_CM_0013 ADJS Create/Modify When the source WCEL is HSDPA-enabled, HSDPAHop-sIdentifier must be defined

HSDPA HOPS MUST BE DEFINED IF HSDPA ENABLED FOR THE SOURCE WCEL

ADJS_CM_0014 ADJS Create/Modify If HSDPAHopsIdentifier is defined, the referred HOPS must exist

HOPS NOT FOUND

ADJS_CM_0015 ADJS Create/Modify When the source WCEL is HSDPA-enabled, and HSDPA with AMR is enabled in the RNC, RTWithHSDPAHopsI-dentifier must be defined

HSDPA HOPS FOR AMR MULTI-SERVICE MUST BE DEFINED FOR THE SOURCE WCEL

ADJS_M_0001 ADJS Modify The parameters related to the target WCEL except AdjsRN-Cid (AdjsMCC, AdjsMNC-Length, AdjsMNC, and AdjsCI) cannot be modified when the target cell is under the same RNC



Object type

Operation type


Table 6 ADJS consistency checking rules (Cont.)

20 DN0934038


Id:0900d8058082585bConfidential

CBCI consistency checking rules

7 CBCI consistency checking rulesThe following table lists the CBCI consistency checking rules.


Object type

Operation type


CBCI_CM_0001 CBCI Create/Modify If CBC is defined, at least one IP address must be defined.

IP ADDRESS NOT DEFINED FOR CBC

CBCI_CM_0002 CBCI Create/Modify If the Service Area Broadcast option is not purchased, CBC cannot be defined.

SAB OPTION IS NOT IN USE IN RNC

CBCI_CM_0003 CBCI Create/Modify IU list must contain PLMN id defined for the CBC.

PLMN ID DEFINED FOR THE CBC (CELL BROADCAST CENTER) NOT FOUND IN CORE NETWORK DEFINI-TIONS

CBCI_CM_0004 CBCI Create/Modify The Radio Network Controller (RNC) object cannot be found in the radio network database.

RNC NOT FOUND

CBCI_M_0001 CBCI Modify If RAN sharing is disabled, only one CBCItem can be defined.

MAXIMUM NUMBER OF CBC (CELL BROADCAST CENTER) EXCEEDED

CBCI_M_0002 CBCI Modify RNC - CBCList - CBCItem - CBCPLMNList - CBCPLMNId (CBC PLMN id) must be unique in the whole CBCList.

PLMN IDS OF CBC (CELL BROADCAST CENTER) MUST BE UNIQUE

CBCI_M_0003 CBCI Modify The CBC item or PLMN id cannot be removed from the CBC item if WCEL(s) with 3 SCCPCH (SAB activated) are mapped (same PLMN id) to it.

SAME PLMN ID DEFINED FOR CBC (CELL BROAD-CAST CENTER) AND WCEL (SAB ACTIVATED)

Table 7 CBCI consistency checking rules

DN0934038 21


CMOB consistency checking rules


8 CMOB consistency checking rulesThe following table lists the CMOB consistency checking rules.


Object type

Operation type


CMOB_C_0001 CMOB Create It is not possible to create more than two CMOB objects whose parameter Restriction-GroupType is RNAR

CS DSAC CMOB COUNT TOO HIGH

CMOB_C_0002 CMOB Create It is not possible to create more than four CMOB objects whose parameter Restriction-GroupType is CS-DSAC

CS DSAC CMOB COUNT TOO HIGH

CMOB_C_0003 CMOB Create It is not possible to create more than four CMOB objects whose parameter Restriction-GroupType is PS-DSAC

PS DSAC CMOB COUNT TOO HIGH

CMOB_C_0004 CMOB Create A forced CMOB cannot be created by the user

USER CANNOT CREATE OR DELETE FORCED TYPE CMOB OBJECT.

CMOB_D_0001 CMOB Delete A CMOB cannot be deleted if there are relations to it from WCEL objects

CMOB OBJECT CANNOT BE DELETED IF RELATED WCELS EXIST

CMOB_D_0002 CMOB Delete A forced CMOB cannot be deleted by the user

USER CANNOT CREATE OR DELETE FORCED TYPE CMOB OBJECT.

CMOB_M_0001 CMOB Modify The CMOB parameter “RestrictionGroupType” cannot be changed

CMOB RESTRICTION TYPE CANNOT BE CHANGED.

Table 8 CMOB consistency checking rules

22 DN0934038


Id:0900d8058088fd0eConfidential

COCO consistency checking rules

9 COCO consistency checking rulesThe following table lists the COCO consistency checking rules.


Object type

Operation type


COCO_CM_001 COCO Create/Modify VP for each link should be found in the VPI list

VP ID OF COCO C-NBAP, D-NBAP, AAL2SIG, AAL2TP LINK SHOULD BE FOUND IN COCO VPI LIST.

COCO_CM_002 COCO Create/Modify COCO PCR parameter check-ing: the sum of all VC’s PCR (PCR for CBR VCC and MDCR for UBR+ VCC) under one VP in COCO should not exceed the corresponding VP’s PCR or MDCR value

SUM OF VCC PCR IS GREATER THAN VP PCR IN ONE COCO

COCO_CM_003 COCO Create/Modify VP already exists in COCO creation, the VP PCR value in COCO should not exceed the existing VP PCR value.

GIVEN VALUE IS TOO BIG

COCO_CM_004 COCO Create/Modify COCO TPI existence check: all ATM TP in the COCO should be found on the platform level

VCLTP DOES NOT EXIST VPLTP DOES NOT EXIST

COCO_CM_005 COCO Create/Modify CBR VCC cannot be config-ured under UBR+ VP in the COCO object.

REQUESTED SERVICE CATEGORY FOR VCLTP IS NOT SUPPORTED IN THE VPCTP (FOR VCCS)

COCO_CM_006 COCO Create/Modify No unused ATM interface, VP in COCO object

UNUSED ATM IF OR VP IN COCO OBJECT.

COCO_CM_007 COCO Create/Modify Bundle usage in AAL2TP link should be found on the bundle list (the related bundle item should be defined).

BUNDLE ITEM IS MISSING IN COCO BUNDLE LIST

COCO_CM_008 COCO Create/Modify One AAL2 UP link should have one AAL2 signaling link asso-ciated

ILLEGAL AAL2 SIGNALING LINK RELATED TO COCO USER PLANE LINK.

COCO_CM_009 COCO Create/Modify The same AAL2 UP VCC should have the same signal-ing link

AAL2 SIGNALING LINK MISMATCH FOR COCO USER PLANE LINK.

COCO_CM_010 COCO Create/Modify The same AAL2 UP VCC should have the same path ID

AAL2 PATH ID MISMATCH

Table 9 COCO consistency checking rules

DN0934038 23




COCO_CM_011 COCO Create/Modify The AAL2 signaling link asso-ciated with AAL2 TP should be found on the AAL2SIG list

UNKNOWN SIGNALLING LINK ID

COCO_CM_012 COCO Create/Modify AAL2 user plane links with equal WAM ID must have the same A2EA

A2EA ADDRESS MISMATCH FOR COCO USER PLANE IN THE SAME WAM.

COCO_CM_013 COCO Create/Modify AAL2 user plane links with equal WAM ID have an equal AAL2 signaling link

AAL2 SIGNALING LINK MISMATCH FOR COCO USER PLANE IN THE SAME WAM.

COCO_CM_014 COCO Create/Modify WAM ID for AAL2TP link should be found on the D-NBAP TTP ID list

WAM ID AND CCP ID DO NOT MATCH

COCO_CM_015 COCO Create/Modify One AAL2SIG link cannot be used for a different WAM

AAL2 SIGNALLING VCI IS USED BY AAL2 UPLINK

COCO_CM_016 COCO Create/Modify AAL2 UP usage should not overlap except when SHARED and DCH overlap is allowed

SHARED OR DEDICATED TRANSPORT SOLUTION SHOULD BE SELECTED FOR ALL AAL2 UP LINKS

COCO_CM_017 COCO Create/Modify The AAL2 path type for the same AAL2UPUsage should be unique; for example, it is impossible to have stringent HSPA and stringent & strin-gent bi-level HSPA in the same COCO

AAL2 PATH TYPES OF AN AAL2UPUSAGE ARE OVER-LAPPED

COCO_CM_018 COCO Create/Modify The AAL2 path type for HSPA VCC (AAL2UPUsage can be HSPA or DCH&HSPA) should be unique in one COCO.

AAL2 PATH TYPES OF AN AAL2UPUSAGE ARE OVER-LAPPED

COCO_CM_019 COCO Create/Modify AAL2UPUsage and AAL2 path type combination:

DCH: Stri, Sbi, Stri&Sbi; DCH&HSDPA: Stri&Sbi&Tol

AAL2 UP USAGE AND AAL2 PATH TYPE COMBINATION IS ILLEGAL

COCO_CM_020 COCO Create/Modify All AAL2 UP links in the same VCC have the same AAL2UPUsage

ALL AAL2 UP LINKS IN SAME VCC MUST HAVE SAME AAL2UPUSAGE VALUE

COCO_CM_021 COCO Create/Modify There can be no more than one HSDPA-dedicated VCC per route

ONLY ONE HSDPA VCC IS ALLOWED PER ROUTE


Object type

Operation type


Table 9 COCO consistency checking rules (Cont.)

24 DN0934038




COCO_CM_022 COCO Create/Modify DCH stringent & DCH stringent bi-level should be included for each route

STRINGENT OR STRIN-GENT BI-LEVEL DCH IS MISSING FROM ROUTE STRINGENT OR STRIN-GENT BI-LEVEL DCH IS MISSING FROM ROUTE

COCO_CM_023 COCO Create/Modify There must be at least one SHARED VCC per WBTS; this rule is dedicated for the poor man's route selection solution. In the poor man solution, DCH + SHARED is allowed, one SHARED VCC is needed for the HSDPA traffic purpose

SHARED VCC IS MISSING FROM CONNECTION CON-FIGURATION OBJECT

COCO_CM_024 COCO Create/Modify At least one RT-DCH and NRT-DCH dedicated VCC per route

RT_DCH OR NRT_DCH DED-ICATED VCC IS MISSING FROM ROUTE

COCO_CM_025 COCO Create/Modify AAL2 UP links in the same VCC must have the same AAL2 path type

AAL2 UP LINKS IN SAME VCC CANNOT HAVE DIF-FERENT PATHTYPE VALUES

COCO_CM_026 COCO Create/Modify Only service-category CBR for VPtp and control plane link and cbr or ubr+ for user plane VCLtp

ERROR IN SERVICE REQUEST

COCO_CM_027 COCO Create/Modify If the ingress category is UBRPLUS, MCR cannot be larger than the corresponding PCR value

ERROR IN SERVICE REQUEST

COCO_CM_028 COCO Create/Modify If coco.coco_data.dsnpath_switch is enabled, NRT VCC should be configured into COCO

MISSING NRT VCC FOR DYNAMIC NRT PATH SELECTION

COCO_CM_029 COCO Create/Modify If coco.coco_data.hsdpa_fl_ctrl_meth_bts is not dynamic, HSDPA VCC cannot be attached in a bundle

NRT DCH VCC IN A BUNDLE DOES NOT MATCH FOR NRT DCH FLOW CONTROL METHOD


Object type

Operation type



DN0934038 25




COCO_CM_030 COCO Create/Modify If a bundle is used in one COCO, either coco.coco_data.dsnpath_switch or coco.coco_data.hsdpa_fl_ctrl_meth_bts should be ON

BUNDLE USAGE DOES NOT MATCH FOR FLOW CONTROL METHOD

COCO_CM_031 COCO Create/Modify SHARED VCC can never be attached in a bundle

SHARED VCC CAN NEVER BE ATTACHED IN A BUNDLE

COCO_CM_033 COCO Create/Modify In a bundle, NRT DCH VCC, HSDPA VCC, HSPA VCC, and HSUPA VCC must be UBR+ type, and RTDCH and DCH VCCs can be either CBR or UBR+ type

SERVICE CATEGORY OF VCC ATTACHED IN A BUNDLE DOES NOT MATCH FOR BUNDLE USAGE

COCO_CM_034 COCO Create/Modify If the user has HSDPA dynamic flow control, a bundle is not used in COCO, and the user cannot modify CBR VCC to UBR+ for HSDPA/HSPA. The reason is that in order for the HSDPA flow control to work with UBR+, the VCC should be in a bundle, and the DSHPATH and PS features are required. UBR+ cannot be sold as one separate feature on top of RAS5.1. So the rule is to ensure that UBR+ and HSDYN is not a possible com-bination

UBR+ SERVICE CATEGORY CANNOT EXIST WITH HSDPA FLOW CONTROL IF BUNDLE IS NOT USED

COCO_CM_035 COCO Create/Modify All DCH (RTDCH, NRTDCH, DCH VCCs) should be in or out of the bundle; it is not allowed to have some DCH inside a bundle and others out of the bundle.

ALL DCH SHOULD BE INSIDE SAME BUNDLE OR OUTSIDE OF BUNDLE

COCO_CM_036 COCO Create/Modify The sum of the PCR (CBR) or the MDCR (UBR+) value of VCCeps inside the same bundle should not exceed the PCR value of the bundle

SUM OF PCR OR MCR OF NCIDS INSIDE BUNDLE EXCEEDS THE BUNDLE PCR


Object type

Operation type



26 DN0934038




COCO_CM_037 COCO Create/Modify TPI consistency checking: 1) The same TPI should not be used by another COCO; 2) The same TPI cannot be used in the same COCO for C-NBAP, D-NBAP, and AAL2SIG; 3) If AAL2 multiplexing is used in the same COCO, AAL2TP can have the same TPI.

GIVEN VCI VALUE IS ALREADY IN USE

COCO_CM_038 COCO Create/Modify PATH ID consistency check-ing: 1) The same Path ID cannot be used in a different COCO; 2) If AAL2 mux is enabled in the same COCO, then the TPI and PATH ID can be the same.

AAL2 PATH ID MISMATCH

COCO_CM_039 COCO Create/Modify A2EA consistency checking: 1) The same A2EA address cannot be found in different COCO; 2) The same A2EA address cannot be found in dif-ferent WAM in the same COCO

COCO AAL2 ADDRESSES NOT UNIQUE

COCO_CM_040 COCO Create/Modify WAM ID cannot be changed because (1) AAL2 multiplexing is not used, and AAL2 path ID is not changed (2) AAL2 multi-plexing is used, and AAL2 path ID and A2EA address are not changed

THE PARAMETER CANNOT BE MODIFIED

COCO_CM_041 COCO Create/Modify There can be only one WAM ID defined for the flexi_bts aal2 generation rule

NOT MORE THAN ONE DNBAPTP CAN BE DEFINED IF COCO-GENERATEAAL2NUM IS 3 (ONE A2EA FOR BTS).

COCO_CM_042 COCO Create/Modify Not more than two VCCs can be allowed per WAM for UltraBTS if AAL2 multiplexing is not enabled

NOT MORE THAN TWO AAL2TP CAN BE DEFINED PER WAMID FOR ULTRA-SITE BTS IF COCO - AAL2MULTIPLEXING IS DIS-ABLED.


Object type

Operation type



DN0934038 27


FMCG consistency checking rules

Id:0900d8058088fd4dConfidential

10 FMCG consistency checking rulesThe following table lists the FMCG consistency checking rules.


Object type

Operation type


FMCG_C_0001 FMCG Create FMCGId must be unique under the RNC

FMCG ALREADY CREATED

FMCG_CM_0001 FMCG Create/Modify The value of NcellSearchPe-riod must be lower than the value of MaxMeasPeriod

FMCG-GSMNCELLSEARCH-PERIOD MUST BE LOWER THAN FMCG-GSMMAX-MEASPERIOD

FMCG_D_0001 FMCG Delete FMCG object cannot be referred to from any WCEL object

FMC STILL USED BY SOME WCEL

FMCG_D_0002 FMCG Delete FMC still used by the VCEL FMC IS STILL BEING USED BY THE VCEL

FMCG_M_0001 FMCG Modify If AMRDirReCell is modified to Enabled, the AdjgSIB parame-ter value of the outgoing GSM neighbor cell definition for Adjgld 0 cannot be No; this is true for all the WCELs that use the FMCG with RtFmcgIdenti-fier


FMCG_M_0002 FMCG Modify WBTS-ICREnabled cannot be set to Enabled if IMSIBasedHO is not set to “allowed(1)” that is, “1” for any WCEL under this cell.

IMSIBASEDGSMHO MUST BE ENBALED FOR ALL THE WCELS UNDER BTS HAVING WBTS-ICREN-ABLED AS ENABLED

Table 10 FMCG consistency checking rules

28 DN0934038


Id:0900d80580825c7eConfidential

FMCI consistency checking rules

11 FMCI consistency checking rulesThe following table lists the FMCI consistency checking rules.


Object type

Operation type


FMCI_C_0001 FMCI Create FMCIId must be unique under the RNC

FMCI ALREADY CREATED

FMCI_CM_0001 FMCI Create/Modify The value of NcellSearchPe-riod must be lower than the value of MaxMeasPeriod

PARAMETER INTERDEPEN-DENCE ERROR

FMCI_CM_0002 FMCI Create/Modify FMCI-InterFreqNcellSearch-Period must be lower than FMCI-InterFreqMaxMeasPe-riod.

FMCI-INTERFREQNCELL-SEARCHPERIOD MUST BE LOWER THAN FMCI-INTER-FREQMAXMEASPERIOD

FMCI_D_0001 FMCI Delete FMCI object cannot be referred to from any WCEL object


FMCI_D_0002 FMCI Delete FMC still used by the VCEL FMC IS STILL BEING USED BY THE VCEL

Table 11 FMCI consistency checking rules

DN0934038 29


FMCS consistency checking rules

Id:0900d8058088fd81Confidential

12 FMCS consistency checking rulesThe following table lists the FMCS consistency checking rules.


Object type

Operation type


FMCS_C_0001 FMCS Create FMCSId must be unique under the RNC

FMCS ALREADY CREATED

FMCS_CM_0001 FMCS Create/Modify EDCHRemEcNoOffset should have at least 2 dB higher value than that defined inEDCHRe-mEcNoOffset to avoid frequent channel type switches between DCH and E-DCH

CHECK FOR CPICH ECNO OFFSET E-DCH USAGE REMOVAL AND ALLOW E-DCH USAGE ECNO OFFSET ERROR

FMCS_CM_0002 FMCS Create/Modify EDCHRemEcNoOffset cannot have a value 0.5dB~1.5dB lower than the value defined in HSDPAServCellWindow

INTERDEPENDENCE BETWEEN EDCHREMEC-NOOFFSET AND HSD-PASERVCELLWINDOW ERROR

FMCS_CM_0003 FMCS Create/Modify HHoRscpThreshold should be lower than HHoRscpCancel

FMCS-HHORSCPCANCEL MUST BE HIGHER THAN FMCS-HHORSCPTHRESH-OLD

FMCS_CM_0004 FMCS Create/Modify FMCS- HHoEcNoThreshold must be lower than the value of FMCS- HhoEcNoCancel.

FMCS- HHOECNOTHRESH-OLD MUST BE LOWER THAN THE VALUE OF FMCS- HHOECNOCANCEL.

FMCS_D_0001 FMCS Delete The FMCS object cannot be referred to from any WCEL object


FMCS_D_0002 FMCS Delete FMC still used by the VCEL FMC IS STILL BEING USED BY THE VCEL

Table 12 FMCS consistency checking rules

30 DN0934038



HOPG consistency checking rules

13 HOPG consistency checking rulesThe following table lists the HOPG consistency checking rules.


Object type

Operation type


HOPG_D_0001 HOPG Delete HOPG object cannot be referred to from any ADJG object

HOP IS USED BY SOME ADJ

HOPG_D_0002 HOPG Delete HOP still used by the VCEL HOPSTILL USED BY THE VCEL

Table 13 HOPG consistency checking rules

DN0934038 31


HOPI consistency checking rules


14 HOPI consistency checking rulesThe following table lists the HOPI consistency checking rules.


Object type

Operation type


HOPI_D_0001 HOPI Delete HOPI object cannot be referred to from any ADJI object


HOPI_D_0002 HOPI Delete HOP still used by the VCEL HOP STILL USED BY THE VCEL

Table 14 HOPI consistency checking rules

32 DN0934038



HOPL consistency checking rules

15 HOPL consistency checking rulesThe following table lists the HOPL consistency checking rules.


Object type

Operation type


HOPL_D_0001 HOPL Delete HOPL cannot be deleted if it is used by ADJL

HOPL CANNOT BE DELETED IF IT IS USED BY ADJL

Table 15 HOPL consistency checking rules

DN0934038 33


HOPS consistency checking rules


16 HOPS consistency checking rulesThe following table lists the HOPS consistency checking rules.


Object type

Operation type


HOPS_D_0001 HOPS Delete HOPS object cannot be referred to from any ADJS object


HOPS_D_0002 HOPS Delete HOP still used by the VCEL HOP STILL USED BY THE VCEL

Table 16 HOPS consistency checking rules

34 DN0934038



IPNB consistency checking rules

17 IPNB consistency checking rulesThe following table lists the IPNB consistency checking rules.


Object type

Operation type


IPNB_CM_001 IPNB Create/Modify CCPid defined for a DNBAP cannot be duplicate

DUPLICATE CCP IDS IN DNBAP LIST

IPNB_CM_002 IPNB Create/Modify At least one CCPid should be defined

NO DEFINED CCP ID

IPNB_CM_003 IPNB Create/Modify The SCTP port should not be out of range (65535)

INVALID DNBAP SCTP PORT

IPNB_CM_004 IPNB Create/Modify SCTP port consistency check-ing: 1) The same SCTP port cannot be found in different IPNBs

SCTP PORT NOT UNIQUE FOR ALL IPNBS.

IPNB_CM_005 IPNB Create/Modify IP Address consistency check-ing: 1) The same IP Address cannot be found in different IPNBs

CONTROL PLANE DESTINA-TION IP ADDRESS CONFIG-URED IN IPNB HAS ALREADY BEEN USED

Table 17 IPNB consistency checking rules

DN0934038 35


IPQM consistency checking rules

Id:0900d805807e030aConfidential

18 IPQM consistency checking rulesThe following table lists the IPQM consistency checking rules.


Object type

Operation type


IPQM_D_0001 IPQM Delete IPQM cannot be deleted if there are relations to it from IU objects

IPQM ID IS IN USE

Table 18 IPQM consistency checking rules

36 DN0934038


Id:0900d8058088fdb3Confidential

IU consistency checking rules

19 IU consistency checking rulesThe following table lists the IU consistency checking rules.


Object type

Operation type


IU_CD_0001 IU Create/Delete If IUCS does not exist, the user cannot define the IUPS core

PLMN ID MUST BE SAME FOR CS AND PS CN (CORE NETWORK)

IU_CM_0001 IU Create/Modify If RAN sharing is not enabled, then the same IU - GlobalCNId - PLMNid - MNC (Mobile Network Code) must be defined for each Iu

DIFFERENT MNC FOR CN

IU_CM_0002 IU Create/Modify If the RAN sharing feature is enabled, Flex IU is disabled for one operator's CN domain (CS or PS), and the MCN feature is disabled, then the same IU - GlobalCNId - PLMNid cannot be defined for the operator's CN domain

IF MOCN/MORAN IS ON THEN UNIQUE PLMN ID MUST BE DEFINED FOR EACH CN.

IU_CM_0003 IU Create/Modify If the MCN and RAN sharing options are OFF, and IuFlex is not in use, only one IU of each domain type is allowed

MAXIMUM NUMBER OF CS CN EXCEEDED MAXIMUM NUMBER OF PS CN EXCEEDED

IU_CM_0004 IU Create/Modify If the primary PLMNid is the same, the secondary plmn list definitions must also be the same

SECONDARY PLMN ID MUST BE UNIQUE UNDER A CERTAIN PRIMARY PLMN ID

IU_CM_0005 IU Create/Modify The primary PLMNid cannot be the same as one of the sec-ondary PLMNid

GLOBAL CN ID MUST BE UNIQUE

IU_CM_0006 IU Create/Modify NRIminforCSCN cannot be greater than NRImaxforCSCN, NRIminforPSCN cannot be greater than NRImaxforPSCN

NRIMINFORCSCN/PSCN CANNOT BE GREATER THAN NRIMAXFORC-SCN/PSCN

IU_CM_0007 IU Create/Modify At least one of the min/max pairs (NRIMaxforCSCN/NRIM-inforCSCN, NRIMaxforPSCN/ NRIMinforPSCN) cannot have the value 1023 (not used) for all configured CN nodes of one operator whose corresponding NRI length is set to non-zero

IF NRILENGTHFORCS OR PSCN IS NONZERO,FOR EACH IU OBJ ATLEAST ONE OF THE MIN/MAX SHOULD INDICATE VALID RANGE.

Table 19 IU consistency checking rules

DN0934038 37




IU_CM_0008 IU Create/Modify If the Flexible IU feature is deactivated, the maximum number of defined CNs is 8

MAXIMUM NUMBER OF DEFINED DEFAULT CNS EXCEEDED

IU_CM_0009 IU Create/Modify Subnet_id cannot be defined if no IP addresses are given

SUBNET_ID CANNOT BE DEFINED WITHOUT IP ADDRESSES

IU_CM_0010 IU Create/Modify The IPQM must exist if it is defined in IU

IPQM NOT FOUND

IU_CM_0011 IU Create/Modify Sum of OperatorWeight under IUO Objects must be 0 or 100.

SUM OF OPERATOR-WEIGHT UNDER IUO OBJECTS MUST BE 0 OR 100

IU_CM_0012 IU Create/Modify MIBPLMNIdIncluded cannot be modified when MOCNen-abled under RNC is enabled.

MIBPLMNIDINCLUDED CANNOT BE MODIFIED WHEN MOCNENABLED UNDER RNC IS ENABLED

IU_CM_0013 IU Create/Modify A null NRI value for CS Pool cannot be given to any MSC of the pool.

NULL NRI VALUE FOR CS POOL CANNOT BE GIVEN TO ANY MSC OF THE POOL

IU_CM_0014 IU Create/Modify A null NRI value for PS Pool cannot be given to any SGSN of the pool.

NULL NRI VALUE FOR PS POOL CANNOT BE GIVEN TO ANY SGSN OF THE POOL

IU_D_0001 IU Delete IU cannot be removed if it is mapped to WCEL(s)

OPERATION DENIED, SOME WCEL(S) CONNECTED TO CN (CORE NETWORK DEFI-NITION IN RNC)

IU_D_0002 IU Delete An IU object cannot be deleted when IuState is other than BAR-US

IU OBJECT CAN NOT BE DELETED WHEN IUSTATE IS OTHER THAN BAR-US

IU_D_0003 IU Delete An IU Object cannot be deleted when IU Primary or Secondary PLMN is configured in the RNC-CBC list

IU OBJECT CAN'T BE DELETED IF IU PRIMARY OR SECONDARY PLMN CON-FIGURED IN RNC-CBC LIST.

IU_D_0004 IU Delete The last IU object cannot be deleted if any WCEL objects exist.

THE LAST IU OBJECT CAN NOT BE DELETED, IF THERE EXIST ANY WCEL OBJECTS

IU_D_0005 IU Delete IU object can not be deleted if IuLinkStatus is enabled.

IU OBJECT CAN NOT BE DELETED, IF IULINKSTATUS IS ENABLED


Object type

Operation type


Table 19 IU consistency checking rules (Cont.)

38 DN0934038




IU_D_0006 IU Delete WCEL-PLMNid must be the same as IUCS/IUPS-PLMNid.

WCEL-PLMNID must be same with IUCS/IUPS-PLMNID

IU_M_0001 IU Modify IU - GlobalCNId (Global CN Id) modification is prohibited

GLOBAL CN ID OF IU CANNOT BE MODIFIED

IU_M_0002 IU Modify The modification of an item of the secondary plmn list is denied if there are any WCEL(s) mapped to that item

OPERATION DENIED, SOME WCEL(S) CONNECTED TO CN (CORE NETWORK DEFI-NITION IN RNC)

IU_M_0003 IU Modify An IU object cannot be modified if a configured IU primary or secondary PLMN causes a conflict with the RNC-CBC list

IU OBJECT CAN'T BE MODIFIED IF IU PRIMARY OR SECONDARY PLMN CONFIGURED CONFLICT WITH RNC-CBC LIST


Object type

Operation type


Table 19 IU consistency checking rules (Cont.)

DN0934038 39


IUO consistency checking rules

Id:0900d805808c02cfConfidential

20 IUO consistency checking rulesThe following table lists the IUO consistency checking rules.


Object type

Operation type


IUO_CM_0001 IUO Create/Modify PLMNID defined in IUO Object should be unique.

PLMNID IN IUO OBJECT SHOULD BE UNIQUE

IUO_CM_0002 IUO Create/Modify IUO-NullNRIForCSPool must be unique within IUO Objects.

IUO-NULLNRIFORCSPOOL MUST BE UNIQUE WITHIN IUO OBJECTS

IUO_CM_0003 IUO Create/Modify IUO-NullNRIForPSPool must be unique within IUO Objects.

IUO-NULLNRIFORPSPOOL MUST BE UNIQUE WITHIN IUO OBJECTS.

IUO_CM_0004 IUO Create/Modify Sum of OperatorWeight under IUO Objects must be 0 or 100.

SUM OF OPERATOR-WEIGHT UNDER IUO OBJECTS MUST BE 0 OR 100

IUO_CM_0005 IUO Create/Modify PLMN ID defined in Global-CNID of IU item cannot be found in IU operator list

PLMN ID IN GLOBALCNID OF IU ITEM NOT FOUND IN PLMNID OF IUO.

IUO_CM_0006 IUO Create/Modify WBTS-ICREnabled is not allowed to be set to Enabled if MORAN is enabled and multiple PLMN IDs exist for host operator in IUO objects

WBTS-ICRENABLED CAN BE ENABLED ONLY WHEN MORAN IS DISABLED

IUO_CM_0007 IUO Create/Modify WBTS-ICR Enabled is not allowed if IUO-ICROpID is undefined in any IUO object.

IUO-ICR OPERATOR ID NOT DEFINED FOR ONE OR MORE IUO OBJECTS

IUO_CM_0008 IUO Create/Modify ICRPLMNid should be unique for every operator and among all the operators (host and roaming partners)

IUO-ICRPLMNID SHALL BE UNIQUE FOR EVERY OPERATOR AND AMONG ALL THE OPERATORS

IUO_CM_0009 IUO Create/Modify IUO-ICROpId should be unique if defined

IUO-ICR OPERATOR ID NOT UNIQUE AMONG IUO OBJECTS

IUO_D_0001 IUO Delete IU operator cannot be deleted or modified because its PLMNID is used by IU item.

IU OPERATOR CANNOT BE DELETED OR MODIFIED BECAUSE ITS PLMNID IS USED BY IU ITEM

IUO_M_0001 IUO Modify A null NRI value for CS Pool cannot be given to any MSC of the pool.

NULL NRI VALUE FOR CS POOL CANNOT BE GIVEN TO ANY MSC OF THE POOL

Table 20 IUO consistency checking rules

40 DN0934038


Id:0900d805808c02cfConfidential

IUO consistency checking rules

IUO_M_0002 IUO Modify A null NRI value for PS Pool cannot be given to any SGSN of the pool.

NULL NRI VALUE FOR PS POOL CANNOT BE GIVEN TO ANY SGSN OF THE POOL

IUO_M_0003 IUO Modify Common PLMN ID is not allowed to be modified if a relation to the WCEL object exists.

COMMON PLMN ID IS NOT ALLOWED TO BE MODIFIED IF RELATION TO WCEL OBJECT EXISTS

IUO_M_0004 IUO Modify MIBPLMNIdIncluded cannot be modified when MOCNen-abled under RNC is enabled.

MIBPLMNIDINCLUDED CANNOT BE MODIFIED, WHEN MOCNENABLED UNDER RNC IS ENABLED

IUO_M_0005 IUO Modify IU object cannot be modified if the IU primary or secondary PLMN configured conflicts with RNC-CBC.

IU OBJECT CANNOT BE MODIFIED IF THE IU PRIMARY OR SECONDARY PLMN CONFIGURED CON-FLICTS WITH RNC-CBC LIST

IUO_MD_0001 IUO Modify/Delete WCEL-PLMNid must be the same as IUCS/IUPS-PLMNid.


IUO_MD_0002 IUO Modify/Delete IUO- ICR OP Id, if associated with any WBTS-r99OpWt-OpId or RNC-HostOpId, shall not be modified/deleted.

IUO-ICR OPERATOR ID IN USE AS WBTS-R99ICROPERATORID OR RNC-HOSTOPERATORID


Object type

Operation type


Table 20 IUO consistency checking rules (Cont.)

DN0934038 41


IUR consistency checking rules

Id:0900d805807e030cConfidential

21 IUR consistency checking rulesThe following table lists the IUR consistency checking rules.


Object type

Operation type


IUR_CM_0001 IUR Create/Modify IURNRncId (Neighbour RNC identifier) and IUR - Neigh-bouringPLMNidList - Neigh-bouringPLMNid (Neighbouring PLMN identity) must be unique within all IUR

RNC ID + PLMN ID PAIR MUST BE UNIQUE WITHIN IUR LIST (NEIGHBOURING RNC LIST)

IUR_CM_0002 IUR Create/Modify Inside each IUR, the Neigh-bouringPLMNid (Neighbour-ing PLMN identity) must be unique.

PLMN IDS OF NEIGHBOUR-ING RNC MUST BE UNIQUE

IUR_CM_0003 IUR Create/Modify At least one Neighbouring-PLMNid must be defined for IUR

PLMN ID FOR NEIGHBOUR-ING RNC NOT DEFINED

IUR_CM_0004 IUR Create/Modify IUR - NRncSignPointCode (Signaling point code of neigh-bour RNC) and IUR - NRnc-NetworkInd (Network indicator of neighbour RNC) must be unique within all IUR in the DB

SIGNALLING POINT CODE MUST BE UNIQUE

IUR_CM_0005 IUR Create/Modify If the IUR-HSPAOverIUR parameter is enabled, RNC-HSDPAMobility and RNC-HSDPADynamicResourceAl-location should be enabled

IUR-HSPAOVERIUR PARAM-ETER CAN BE ENABLED ONLY WHEN RNC-HSDPA-DYNAMICRESOURCEALLO-CATION IS ENABLED

IUR_CM_0006 IUR Create/Modify If the IUR-HSPAOverIUR parameter is enabled, IUR-NRncVersion should have a value corresponding to Rel 6 or later

IUR-HSPAOVERIUR PARAM-ETER CAN BE ENABLED ONLY WHEN IUR-NRNC-VERSION SHOULD HAVE VALUE GREATER OR EQUAL TO REL6

IUR_CM_0007 IUR Create/Modify The value of IUR-DelayTh-resholdMaxIur has to be greater than IUR-DelayTh-resholdMidIur

IUR-DELAYTHRESHOLD-MAXIUR MUST BE GREATER THAN IUR-DELAYTHRESHOLDMIDIUR

IUR_CM_0008 IUR Create/Modify The value of IUR-DelayTh-resholdMidIur has to be greater than IUR-DelayTh-resholdMinIur

IUR-DELAYTHRESHOLD-MIDIUR MUST BE GREATER THAN IUR-DELAYTHRESH-OLDMINIUR

Table 21 IUR consistency checking rules

42 DN0934038



IUR consistency checking rules

IUR_CM_0009 IUR Create/Modify The relation between SRNC and ADA cannot be defined both in ControllerIdPair and IUR

THE RELATION BETWEEN SRNC AND ADA CAN NOT BE DEFINED BOTH IN CON-TROLLERIDPAIR AND IUR

IUR_CM_0010 IUR Create/Modify IBTSSharing can be set to enable only when the Neigh-bouringRNWElement is ADA

IBTSSHARING CAN BE SET TO ENABLE ONLY WHEN THE NEIGHBOURINGRN-WELEMENT IS ADA

IUR_CM_0011 IUR Create/Modify IBTSSharing can be supported only when IUR user plane and cell DCH relocation are both supported

IBTSSHARING CAN BE SUP-PORTED ONLY WHEN IUR USER PLANE AND CELL DCH RELOCATION BOTH ARE SUPPORTED

IUR_CM_0012 IUR Create/Modify If NeighboringRNWElement is set to IHSPA Adapter, then the value of NRncVersion should be internally set to Rel6

IF NEIGHBORINGRNWELE-MENT IS SET TO IHSPA ADAPTER, NRNCVERSION SHOULD BE SET TO REL6

IUR_CM_0013 IUR Create/Modify One and only one PLMN ID should be configured for those IURs which support IBTSShar-ing

ONE AND ONLY ONE PLMN ID SHOULD BE CONFIG-URED FOR THOSE IURS WHICH SUPPORT IBTSSHARING

IUR_CM_0014 IUR Create/Modify PLMNId of IURs which support IBTSSharing must be same

PLMNID OF IURS WHICH SUPPORT IBTSSHARING MUST BE SAME

IUR_CM_0015 IUR Create/Modify The number of IUR objects showing Neighboring RNC exceeds the limit

THE MAX NUMBER OF IUR OBJECTS WHO NEIGH-BOURING RNC IS 32


Object type

Operation type


Table 21 IUR consistency checking rules (Cont.)

DN0934038 43


RNAC consistency checking rules

Id:0900d8058088fee6Confidential

22 RNAC consistency checking rulesThe following table lists the RNAC consistency checking rules.


Object type

Operation type


RNAC_CM_0001 RNAC Create/Modify WBTS-ICR Enabled cannot be set to enabled if RNC-HostOpId is not a defined IUO-ICROpId

RNC-ICRHOSTOPERATO-RID MUST MATCH WITH ATLEAST ONE IUO-ICROPE-ATORID

Table 22 RNAC consistency checking rules

44 DN0934038


Id:0900d805808902a0Confidential

RNC consistency checking rules

23 RNC consistency checking rulesThe following table lists the RNC consistency checking rules.


Object type

Operation type


RNC_CM_0001 RNC Create/Modify LCS Support for Anchoring can be enabled only when the parameter LCS Functionality is enabled

LCS SUPPORT FOR ANCHORING CAN BE ENABLED ONLY WHEN PARAMETER LCS FUNC-TIONALITY IS ENABLED

RNC_CM_0002 RNC Create/Modify RNC-LCSfunctionality cannot be disabled when WSMLC-UEBasedAGPS is enabled.

RNC-LCSFUNCTIONALITY CANT BE DISABLED WHEN WSMLC-UEBASEDAGPS IS ENABLED

RNC_CM_0003 RNC Create/Modify The value of the parameter SIB18 priority must not be higher than the value of the parameter SIB11/12 priority

PRIORITY OF SIB18 MUST NOT BE HIGHER THAN PRIORITY OF SIB11 OR SIB12

RNC_CM_0004 RNC Create/Modify RAN sharing and IMSI HO are not supported, only one PLMN id is allowed for one CBC

MAXIMUM NUMBER OF PLMN IDS FOR CBC (CELL BROADCAST CENTER) EXCEEDED

RNC_CM_0005 RNC Create/Modify RNC - DefaultAuthorisedNet-workId (Identifier of the Default Authorised Network) must point to the existing WANE object if the value is not 0.

WANE NOT FOUND

RNC_CM_0006 RNC Create/Modify The value of DelayThreshold-Mid always has to be lower than the value of DelayThresh-oldMax, unless DelayThresh-oldMax has the value HSUPA CC mechanism disabled.

INTERDEPENDENCE BETWEEN DELAYTHRESH-OLDMIN, DELAYTHRESH-OLDMID AND DELAYTHRESHOLDMAX ERROR

RNC_CM_0007 RNC Create/Modify WBTS-ICR Enabled cannot be set as enabled if RNC-HostOpId is not a defined IUO-ICROpId


RNC_M_0001 RNC Modify RncId (RNC Identifier) is not modifiable

RNC IDENTIFIER MAY NOT BE CHANGED

RNC_M_0002 RNC Modify AMRwithHSDSCH is not allowed to be set to Enabled if the special value “Not defined” is set to the parameter RTWith-HSDPAFmcsIdentifier.

RT HSDPA FMCS identifier for AMR multi-service must be defined for all the WCELLs and ADJS under this RNC.

Table 23 RNC consistency checking rules

DN0934038 45


RNC consistency checking rules

Id:0900d805808902a0Confidential

RNC_M_0003 RNC Modify AMRwithHSDSCH is not allowed to be set to Enabled if the special value “Not defined” is set to the parameter RTWith-HSDPAFmciIdentifier.


RNC_M_0004 RNC Modify AMRwithHSDSCH is not allowed to be set to Enabled if the special value “Not defined” is set to the parameter RTWith-HSDPAFmcgIdentifier.


RNC_M_0005 RNC Modify AMRwithHSDSCH is not allowed to be set to Enabled if the special value “Not defined” is set to the parameter RTWith-HSDPAHopsIdentifier.

HSDPA HOPS FOR AMR MULTI-SERVICE MUST BE DEFINED FOR THE OUTGOING ADJS OF THE WCEL

RNC_M_0006 RNC Modify WBTS-BroadcastSIB15 cannot be enabled when the RNC-LCSFunctionality is not enabled.

WBTS-BROADCASTSIB15 CAN NOT BE USED WHEN RNC-LCSFUNCTIONALITY IS NOT ENABLED.

RNC_M_0007 RNC Modify MOCN WCEL can be created or modified only if MOCNen-abled is set to enable. MOC-Nenabled can be set to disable only if no MOCN WCEL exists.

MOCN WCEL CAN BE CON-FIGURED ONLY IF MOC-NENABLED IS ENABLE. MOCNENABLED CAN BE DISABLED IF NO MOCN WCEL EXISTS

RNC_M_0008 RNC Modify LCS Support for Anchoring can be enabled only when the Operational Mode of LCS is RNC Centric Mode.

LCS SUPPORT FOR ANCHORING CAN BE ENABLED ONLY WHEN OPERATIONAL MODE IS RNC CENTRIC MODE


Object type

Operation type


Table 23 RNC consistency checking rules (Cont.)

46 DN0934038


Id:0900d805808c0385Confidential

RNFC consistency checking rules

24 RNFC consistency checking rulesThe following table lists the RNFC consistency checking rules.


Object type

Operation type


RNFC_CM_0006 RNFC Create/Modify RNC-HSPAOverIurExt param-eter can be enabled only when RNC-HSDPAMobility is enabled.

RNC-HSPAOVERIUREXT PARAMETER CAN BE ENABLED ONLY WHEN RNC-HSDPAMOBILITY IS ENABLED

RNFC_CM_0007 RNFC Create/Modify RNC-HSPAOverIurExt param-eter can be enabled only when RNC-HSDPADynamicRe-sourceAllocation is enabled.

RNC-HSPAOVERIUREXT PARAMETER CAN BE ENABLED ONLY WHEN RNC-HSDPADYNAMICRE-SOURCEALLOCATION IS ENABLED

RNFC_CM_0008 RNFC Create/Modify An attempt has been made to enable options IEMISHO and EMISHO simultaneously. This is not allowed.

ATTEMPTED TO ENABLE OPTIONS IEMISHO AND EMISHO SIMULTANEOUSLY

RNFC_M_0001 RNFC Modify The AMRWithEDCH parame-ter is valid only if AMRWith-HSDSCH is enabled.

AMRWITHEDCH IS VALID ONLY IF AMRWITHHSDSCH IS ENABLED

RNFC_M_0002 RNFC Modify If HSDPA16KBPSReturnChannel is Off, the 16 kbps value is not allowed for the following parameters: HSDPAminAl-lowedBitrateUL and HSD-PAinitialBitrateUL.

HSDPA16KRETURNCHANNEL NOT ON

RNFC_M_0003 RNFC Modify The value of RNC-FlexULRL-CEnabled can be enabled only when RNC-FRLCEnabled is enabled.

RNC FLEXULRLCENABLED CAN BE ENABLED ONLY WHEN RNC FRLCENABLED IS ENABLED

RNFC_M_0004 RNFC Modify WCEL-HSFACHEnabled can be enabled only when RNC-FRLCEnabled is enabled.

WCEL-HSFACHENABLED CAN BE ENABLED ONLY WHEN RNC-FRLCENABLED IS ENABLED

RNFC_M_0005 RNFC Modify WCEL-HSFACHEnabled can be enabled only when RNC-HSDPADynamicResourceAl-location is enabled.

WCEL-HSFACHENABLED CAN BE ENABLED ONLY WHEN RNC-HSDPADYNAMI-CRESOURCEALLOCATION IS ENABLED

Table 24 RNFC consistency checking rules

DN0934038 47




RNFC_M_0006 RNFC Modify HSDPA64QAMallowed can be enabled only when FRLCEn-abled is enabled; FRLCEn-abled can be disabled only if all HSDPA64QAMallowed is dis-abled.

HSDPA64QAMALLOWED CAN BE ENABLED ONLY WHEN FRLCENABLED IS ENABLED.

RNFC_M_0007 RNFC Modify FRLCEnabled can be enabled only when HSDPA dynamic resource allocation is enabled; HSDPA dynamic resource allocation can be disabled only if FRLCEnabled is disabled.

FRLCENABLED CAN BE ENABLED ONLY WHEN HSDPA DYNAMIC RESOURCE ALLOCATION IS ENABLED

RNFC_M_0008 RNFC Modify WCEL-DCellHSDPAEnabled can be enabled only when RNC-HSDPAMobility is enabled.

WCEL-DCELLHSDPAEN-ABLED CAN BE ENABLED ONLY WHEN RNC-HSDPA-MOBILITY IS ENABLED

RNFC_M_0009 RNFC Modify RNC-RABDRAEnabled can be set to enabled only when RNC-HSDPADynamicResourceAl-location is set to enabled.

RNC-RABDRAENABLED CAN BE SET ENABLED ONLY WHEN RNC-HSDPA-DYNAMICRESOURCEALLO-CATION IS SET ENABLED

RNFC_M_0010 RNFC Modify Minimum allowed bitrate for HSDPA UL DCH for NRT with streaming can be 16 kbps only if the HSDPA 16 kbps UL DCH return channel switch is turned on.

HSDPAMINBRULSTRNRT CAN BE 16 KBPS ONLY IF HSDPA16KBPSRETURNCHANNEL IS ENABLED

RNFC_M_0011 RNFC Modify If the Wireless Priority Service feature is enabled, then AdjgSIB is set to Enabled for every outgoing ADJG whose parameter ADJGid equals 0 of every WCEL.

ADJGSIB IS NOT ENABLED FOR WPS ADJG IN ONE OR MORE WCEL IN RNC RNW DATABASE

RNFC_M_0012 RNFC Modify AMRwithEDCH is not allowed to be set to enabled if the special value “Not defined” is set to the parameter RTWithH-SPAFmcsIdentifier.

HSPA FMCS IDENTIFIER FOR AMR MULTI-SERVICE NOT DEFINED

RNFC_M_0013 RNFC Modify HSDPA dynamic resource allocation cannot be disabled when HSDPA 14Mbps per user is enabled.

HSDPA 14MBPS PER USER CAN BE ENABLED ONLY IF HSDPA DYNAMIC RESOURCE ALLOCATION IS ENABLED


Object type

Operation type


Table 24 RNFC consistency checking rules (Cont.)

48 DN0934038




RNFC_M_0014 RNFC Modify If the parameter HSPA QoS Enabled indicates that HSPA QoS is used for NRTs, or HSPA streaming is in use, HSDPA Dynamic Resource Allocation must be enabled.

HSPA QOS FOR NRT, HSPA STREAMING, CS VOICE OR HSPA STREAMING CS VOICE CAN BE USED IF HSDPA DYN RES ALLOC USED

RNFC_M_0015 RNFC Modify If the parameter HSDPADy-namicResourceAllocation is modified, all HSDPA wcels must be locked.

OPERATION REQUIRES WCEL OBJECT TO BE LOCKED

RNFC_M_0016 RNFC Modify If HSDPADynamicRe-sourceAllocation changes to Enable, the rule PtxTarget >= PtxTargetPSMax >= PtxTar-getPSMin must be matched in all hsdpa WCELs.

PTXTARGET LESS THAN PTXTARGETPS-MAX PARAMETER INTERDEPEN-DENCE ERROR

RNFC_M_0017 RNFC Modify HSDPAMobility can be Disabled only when no cells are using HSUPA.

HSUPAEnabled CAN BE ENABLED IF HSDPAMobility IS ENABLED;HSDPAMobility CAN BE DISABLED IF NO WCEL USE HSUPA

RNFC_M_0018 RNFC Modify HSPAQoSEnabled can be set to cs_voice_c or str_cs_c only when AMRWithHSDSCH is Enabled.

HSPAQOSENABLED CAN BE SET TO CS_VOICE_C OR STR_CS_C ONLY WHEN AMRWITHHSDSCH IS ENABLED

RNFC_M_0019 RNFC Modify HSPAQoSEnabled can be set to cs_voice_c or str_cs_c only when AMRWithEDCH is Enabled.

HSPAQOSENABLED CAN BE SET TO CS_VOICE_C OR STR_CS_C ONLY WHEN AMRWITHEDCH IS SET TO ENABLED

RNFC_M_0020 RNFC Modify WCEL-DCellHSDPAEnabled can be enabled only when RNFC-FRLCEnabled is enabled.

WCEL-DCELLHSDPAEN-ABLED CAN BE ENABLED ONLY WHEN RNFC-FRL-CENABLED IS ENABLED

RNFC_M_0021 RNFC Modify WCEL- HSPAQoSEnabled can be set to cs_voice_c only when RNFC-FRLCEnabled is set to Enabled.

WCEL-HSPAQOSENABLED CAN BE SET TO CS_VOICE_C ONLY WHEN RNFC-FRLCENABLED IS SET TO ENABLED


Object type

Operation type



DN0934038 49




RNFC_M_0022 RNFC Modify HSDPA 14Mbps per user can be enabled only when HSDPA dynamic resource allocation is enabled. HSDPA dynamic resource allocation cannot be disabled when HSDPA 14Mbps per user is enabled.


RNFC_M_0023 RNFC Modify IUR-HSPAOverIUR can be enabled only when RNFC-HSDPAMobility is enabled.

IUR-HSPAOVERIUR CAN BE ENABLED ONLY WHEN RNFC-HSDPAMOBILITY IS ENABLED

RNFC_M_0024 RNFC Modify IUR-HSPAOverIUR can be enabled only when RNFC-HSDPADynamicResourceAl-location is enabled.

IUR-HSPAOVERIUR CAN BE ENABLED ONLY WHEN RNFC-HSDPADYNAMICRE-SOURCEALLOCATION IS ENABLED

RNFC_M_0025 RNFC Modify WBTS-ICREnabled cannot be set to Enabled if RNC-MOC-NEnabled is Enabled.

WBTS-ICRENABLED CAN BE ENABLED ONLY WHEN RNC-MOCNENABLED IS DISABLED


Object type

Operation type



50 DN0934038


Id:0900d805808258efConfidential

RNHSPA consistency checking rules

25 RNHSPA consistency checking rulesThe following table lists the RNHSPA consistency checking rules.


Object type

Operation type


RNHSPA_CM_0001 RNHSPA Create/Modify The value of the parameter HSDPAMinAllowedBitrateUl must be lower than or equal to the parameter HSDPAInitial-BitrateUl.

HSDPAINITIALBITRATEUL MUST BE GREATER THAN OR EQUAL TO HSDPAMI-NALLOWEDBITRATEUL

RNHSPA_CM_0002 RNHSPA Create/Modify The value of the parameter ThresholdMaxEDPDCHSR1920kbps must be higher than the value of the parameter ThresholdMaxEDPDCHSR960kbps.

THRESHOLDMAXEDPDCHSR1920KBPS MUST BE GREATER THAN THRESHOLDMAXEDPDCHSR960KBPS

RNHSPA_CM_0003 RNHSPA Create/Modify The value of ThresholdMaxEDPDCHSR3840kbps must be higher than the value of the parameter ThresholdMaxEDPDCHSR1920kbps.

THE VALUE OF THRESHOLDMAXEDPDCHSR3840kbps IS NOT LARGER THAN VALUE OF THRESHOLDMAXEDPDCHSR1920kbps

RNHSPA_CM_0004 RNHSPA Create/Modify The initial bitrate for HSDPA UL DCH for NRT with stream-ing must be greater than or equal to the minimum allowed bitrate for HSDPA UL DCH for NRT with streaming.

INITIAL BR FOR HSDPA UL DCH FOR NRT WITH STREAMING CANNOT BE SMALLER THAN MIN ALLOWED BR

RNHSPA_CM_0005 RNHSPA Create/Modify The value of the parameter HSDPAMinAllowedBitrateUl must be lower than or equal to the parameter HSDPAInitial-BitrateUl.

HSDPAINITIALBITRATEUL MUST BE GREATER THAN OR EQUAL TO HSDPAMI-NALLOWEDBITRATEUL

RNHSPA_CM_0006 RNHSPA Create/Modify RNC-Thresholdmaxedpdchsr3840Kbps must be higher than RNC-Thresholdmaxedpdchsr960Kbps.

RNC-THRESHOLDMAXEDPDCHSR3840KBPS MUST BE GREATER THAN RNC-THRESHOLDMAXEDPDCHSR960KBPS

RNHSPA_M_0001 RNHSPA Modify The priorities of HSPA NBR in the uplink direction must form a continuous block of priori-ties used for NRTs.

PRIORITIES WITH NBR AT UL DIRECTION MUST COVER FROM THE HIGHEST PRIORITIES USED FOR NRTS

Table 25 RNHSPA consistency checking rules

DN0934038 51


RNHSPA consistency checking rules

Id:0900d805808258efConfidential

RNHSPA_M_0002 RNHSPA Modify The priorities with HSPA NBR in the downlink direction must form a continuous block of pri-orities used for NRTs.

PRIORITIES WITH NBR AT DL DIRECTION MUST COVER FROM THE HIGHEST PRIORITIES USED FOR NRTS

RNHSPA_M_0003 RNHSPA Modify If HSDPA16KBPSReturnChannel is Off, the 16 kbps value is not allowed for the following parameters: HSDPAminAl-lowedBitrateUL and HSD-PAinitialBitrateUL.

HSDPA16KRETURNCHANNEL NOT ON


Object type

Operation type


Table 25 RNHSPA consistency checking rules (Cont.)

52 DN0934038


Id:0900d805808902bcConfidential

RNMOBI consistency checking rules

26 RNMOBI consistency checking rulesThe following table lists the RNMOBI consistency checking rules.


Object type

Operation type


RNMOBI_CM_0001 RNMOBI Create/Modify The value of FAST UE THRESHOLD must be greater than the value of FAST UE CANCEL.

FAST UE THRESHOLD NOT GREATER THAN FAST UE CANCEL

RNMOBI_M_0001 RNMOBI Modify HSDPAChaTypeSwitchWin-dow must have a lower value than the value used in HSD-PAServCellWindow.

HSDPACHATYPESWITCH-WINDOW NOT LESS THAN HSDPASERVCELLWINDOW

RNMOBI_M_0002 RNMOBI Modify When the Flexible Iu feature is activated, a maximum of eight CN nodes can be con-figured as default CNs for routing.


RNMOBI_M_0003 RNMOBI Modify If HSDPAServCellWindow is modified, FMCS- EDCHRe-mEcNoOffset cannot have a value that is 0.5dB~1.5dB lower than HSDPAServCell-Window.

INTERDEPENDENCE BETWEEN EDCHREMEC-NOOFFSET AND HSD-PASERVCELLWINDOW ERROR

Table 26 RNMOBI consistency checking rules

DN0934038 53


RNPS consistency checking rules

Id:0900d805808258f1Confidential

27 RNPS consistency checking rulesThe following table lists the RNPS consistency checking rules.


Object type

Operation type


RNPS_CM_0001 RNPS Create/Modify The value of PriForSRB-sOnHSPA must be greater than the values assigned to the parameters PriForStreamARP1, PriForStreamARP2, and PriForStreamARP3.

PriForSRBsOnHSPA MUST BE BIGGER THAN PriForCon-vOnHSPA,PriForStreamARP1,PriForStreamARP2 AND PriForStreamARP3

RNPS_CM_0002 RNPS Create/Modify Priorities for streaming RABs must be greater than the priority of interactive signaling RABs.

PRIORITIES FOR STREAM-ING RABS MUST BE BIGGER THAN PRIORITY FOR INTERACTIVE SIGNALING RABS

RNPS_CM_0003 RNPS Create/Modify If RT over NRT is used for a specific ARP category, the priority set for interactive sig-naling RABs must be greater than the priority of thresholds RT over NRT.

PRIORITIES FOR STREAM-ING RABS MUST BE BIGGER THAN PRIORITY FOR INTERACTIVE SIGNALING RABS

RNPS_CM_0004 RNPS Create/Modify The priority for interactive sig-naling RABs must be greater than the priorities of other inter-active and background RABs.

PRIORITY FOR INTERAC-TIVE SIGNALING RABS MUST BE BIGGER THAN PRIORITIES FOR OTHER NRT RABS

RNPS_CM_0005 RNPS Create/Modify The value of PriForHSFACH-DTCH must be less than PriFo-rIntSignaling.

VALUE OF PRIFORHSFACH-DTCH MUST BE LESS THAN PRIFORINTSIGNALING

RNPS_CM_0006 RNPS Create/Modify PriForConvOnHSPA must take values higher than PriForStreamARP1, PriForStreamARP2, and PriForStreamARP3.

PRIFORCONVONHSPA MUST TAKE VALUES BIGGER THAN PRIFORSTREAMARP1, PRIFORSTREAMARP2 AND PRIFORSTREAMARP3

Table 27 RNPS consistency checking rules

54 DN0934038



RNRLC consistency checking rules

28 RNRLC consistency checking rulesThe following table lists the RNRLC consistency checking rules.


Object type

Operation type


RNRLC_CM_0001 RNRLC Create/Modify The value of RNC-AMRLCRelatTXWindowRate1 should be lower than or equal to the value of the parameter RNC-AMRLCRelatTXWindowRate2

RNC-AMRLCRELATTXWINDOWRATE1 SHOULD BE SMALLER THAN OR EQUAL TO RNC-AMRLCRELATTXWINDOWRATE2.



RNRLC_CM_0003 RNRLC Create/Modify The value of the RNC-AMRLCRelatTXWindowRate3 should be lower than or equal to the value of the parameter RNC-AMRLCRelatTXWindowRate4








Table 28 RNRLC consistency checking rules

DN0934038 55


RNRLC consistency checking rules





Object type

Operation type


Table 28 RNRLC consistency checking rules (Cont.)

56 DN0934038



RNTRM consistency checking rules

29 RNTRM consistency checking rulesThe following table lists the RNTRM consistency checking rules.


Object type

Operation type


RNTRM_M_0001 RNTRM Modify When the Flexible Iu feature is activated, a maximum of eight CN nodes can be configured as default CNs for routing.


Table 29 RNTRM consistency checking rules

DN0934038 57


TQM consistency checking rules

Id:0900d805807e030eConfidential

30 TQM consistency checking rulesThe following table lists the TQM consistency checking rules.


Object type

Operation type


TQM_D_0001 TQM Delete TQM cannot be deleted if there are relations to it from WBTS objects

THE TQM IS STILL USED BY SOME WBTSs

Table 30 TQM consistency checking rules

58 DN0934038


Id:0900d805807e030fConfidential

VBTS consistency checking rules

31 VBTS consistency checking rulesThe following table lists the VBTS consistency checking rules.


Object type

Operation type


VBTS_CM_0001 VBTS Create/Modify The relation between SRNC and ADA cannot be defined both in ControllerIdPair and IUR

THE RELATION BETWEEN SRNC AND ADA CAN NOT BE DEFINED BOTH IN CON-TROLLERIDPAIR AND IUR

VBTS_CM_0002 VBTS Create/Modify One ADA can be used by only one RNC for IBTS Sharing

ONE ADA CAN BE USED BY ONLY ONE RNC FOR IBTS SHARING

Table 31 VBTS consistency checking rules

DN0934038 59


VCEL consistency checking rules


32 VCEL consistency checking rulesThe following table lists the VCEL consistency checking rules.


Object type

Operation type


VCEL_CM_001 VCEL Create/Modify If parameter VCEL-HSUPAEn-abled is enabled, VCEL-HSD-PAEnabled should be enabled

VCEL-HSUPAENABLED IS ENABLED, THEN VCEL-HSDPAENABLED MUST BE ENABLED.

VCEL_CM_002 VCEL Create/Modify VCEL-HSDPAFmcsIdentifier should have a value other than “not defined” if VCEL-HSD-PAenabled is set to “enabled”.

VCEL-HSDPAFMCSIDENTI-FIER MUST BE DEFINED IF VCEL-HSDPAENABLED IS ENABLED

VCEL_CM_003 VCEL Create/Modify If parameter VCEL-HSDPAF-mcsIdentifier is set to a value other than “not defined”, the FMCS object with the corre-sponding FMCSId should exist in the database.

FMCS NOT FOUND

VCEL_CM_004 VCEL Create/Modify VCEL-HSDPAFmciIdentifier should have a value other than “not defined” if VCEL-HSD-PAenabled is set to “enabled”.

VCEL-HSDPAFMCIIDENTI-FIER MUST BE DEFINED IF VCEL-HSDPAENABLED IS ENABLED

VCEL_CM_005 VCEL Create/Modify If parameter VCEL-HSDPAF-mciIdentifier is set to a value other than “not defined”, the FMCI object with the corre-sponding FMCIId should exist in the database.

FMCI NOT FOUND

VCEL_CM_006 VCEL Create/Modify VCEL-HSDPAFmcgIdentifier should have a value other than “not defined” if VCEL-HSD-PAenabled is set to “enabled”.

VCEL-HSDPAFMCGIDENTI-FIER MUST BE DEFINED IF VCEL-HSDPAENABLED IS ENABLED

VCEL_CM_007 VCEL Create/Modify If parameter VCEL-HSDPAF-mcgIdentifier is set to a value other than “not defined”, the FMCG object with the corre-sponding FMCGId should exist in the database.

FMCG NOT FOUND

VCEL_CM_008 VCEL Create/Modify VCEL-HSDPAHopsIdentifier should have a value other than “not defined” if VCEL-HSD-PAenabled is set to “enabled”.

VCEL-HSDPAHOPSIDENTI-FIER MUST BE DEFINED IF VCEL-HSDPAENABLED IS ENABLED

Table 32 VCEL consistency checking rules

60 DN0934038




VCEL_CM_009 VCEL Create/Modify If parameter VCEL-HSDPA-HopsIdentifier is set to a value other than “not defined”, the HOPS object with the corre-sponding HOPSId should exist in the database.

HOPS NOT FOUND

VCEL_CM_010 VCEL Create/Modify VCEL-HSPAFmcsIdentifier should have a value other than “not defined” if VCEL-HSU-PAenabled is set to “enabled”

VCEL-HSPAFMCSIDENTI-FIER MUST BE DEFINED IF VCEL-HSUPAENABLED IS ENABLED

VCEL_CM_011 VCEL Create/Modify If parameter VCEL-HSPAFmc-sIdentifier is set to a value other than “not defined”, the FMCS object with the corre-sponding FMCSId should exist in the database.

FMCS NOT FOUND

VCEL_CM_012 VCEL Create/Modify MaxBitRateDLPSNRT should be higher than or equal to Ini-tialBitRateDL

MAXBITRATEDLPSNRT SHOULD BE BIGGER THAN OR EQUAL TO INITIALBI-TRATEDL

VCEL_CM_013 VCEL Create/Modify InitialBitRateDL should be higher than or equal to MinAl-lowedBitRateDL

INITIALBITRATEDL SHOULD BE BIGGER THAN OR EQUAL TO MINALLOWEDBI-TRATEDL

VCEL_CM_014 VCEL Create/Modify FMC still used by the VCEL FMC STILL USED BY THE VCEL

VCEL_CM_015 VCEL Create/Modify HOP still used by the VCEL HOP STILL USED BY THE VCEL

VCEL_CM_016 VCEL Create/Modify MaxBitRateULPSNRT should be higher than or equal to Ini-tialBitRateUL.

MAXBITRATEULPSNRT SHOULD BE BIGGER THAN OR EQUAL TO INITIALBI-TRATEUL

VCEL_CM_017 VCEL Create/Modify VCEL-RTwithHSDPAFmcsI-dentifier must be defined if RNC-AMRWithHSDSCH and VCEL-HSDPAenabled are enabled.

VCEL-RTWITHHSDPAFMC-SIDENTIFIER MUST BE DEFINED IF RNC-AMRWITH-HSDSCH AND VCEL-HSD-PAENABLED ARE ENABLED

VCEL_CM_018 VCEL Create/Modify VCEL-RTwithHSDPAFmciI-dentifier must be defined if RNC-AMRWithHSDSCH and VCEL-HSDPAenabled are enabled.

VCEL-RTWITHHSDPAFMCII-DENTIFIER MUST BE DEFINED IF RNC-AMRWITH-HSDSCH AND VCEL-HSD-PAENABLED ARE ENABLED


Object type

Operation type


Table 32 VCEL consistency checking rules (Cont.)

DN0934038 61




VCEL_CM_019 VCEL Create/Modify VCEL-RTwithHSDPAFmcgI-dentifier must be defined if RNC-AMRWithHSDSCH and VCEL-HSDPAenabled are enabled.

VCEL-RTWITHHSDPAFM-CGIDENTIFIER MUST BE DEFINED IF RNC-AMRWITH-HSDSCH AND VCEL-HSD-PAENABLED ARE ENABLED

VCEL_CM_020 VCEL Create/Modify VCEL-RTwithHSDPAHopsI-dentifier must be defined if RNC-AMRWithHSDSCH and VCEL-HSDPAenabled are enabled.

VCEL-RTWITHHSDPAHOP-SIDENTIFIER MUST BE DEFINED IF RNC-AMRWITH-HSDSCH AND VCEL-HSD-PAENABLED ARE ENABLED

VCEL_CM_021 VCEL Create/Modify VCEL-RTwithHSPAFmcsIden-tifier must be defined if RNC-AMRWithEDCH and VCEL-HSUPAenabled are enabled.

VCEL-RTWITHHSPAFMCSI-DENTIFIER MUST BE DEFINED IF RNC-AMR-WITHEDCH AND VCEL-HSU-PAENABLED ARE ENABLED

VCEL_CM_022 VCEL Create/Modify The value of InitialBitRateUL should be higher than or equal to the value of MinAllowedBi-tRateUL.

INITIALBITRATEUL SHOULD BE BIGGER THAN OR EQUAL TO MINALLOWEDBI-TRATEUL


Object type

Operation type


Table 32 VCEL consistency checking rules (Cont.)

62 DN0934038



WANE consistency checking rules

33 WANE consistency checking rulesThe following table lists the WANE consistency checking rules.


Object type

Operation type


WANE_D_0001 WANE Delete A WANE object cannot be deleted if it is referred to from WSG

THERE ARE WSG RELATED TO WANE

WANE_D_0002 WANE Delete A WANE object cannot be deleted if RNC - DefaultAutho-risedNetworkId refers to it

DEFAULT WANE CANNOT BE DELETED

Table 33 WANE consistency checking rules

DN0934038 63


WBTS consistency checking rules

Id:0900d805808be25bConfidential

34 WBTS consistency checking rulesThe following table lists the WBTS consistency checking rules.


Object type

Operation type


WBTS_C_0001 WBTS Create WBTSId must be unique under the RNC

WBTS ALREADY CREATED

WBTS_C_0002 WBTS Create WBTS creation failed because the maximum number of WBTSs has already been created in the RNW database.

MAXIMUM NUMBER OF WBTSS EXCEEDED

WBTS_CM_0001 WBTS Create/Modify SharedHSDPAFlowControlAl-location should be greater than or equal to the value of the SharedHSDPAallocation in the same WBTS.

SHAREDHSDPAALLOCA-TION GREATER THAN SHAREDHSDPAFLOWCON-TROLALLOCATION

WBTS_CM_0002 WBTS Create/Modify WBTS - ATMInterfaceID (ATM interface identifier) / VPI / VCI and WBTS - COCOId (Con-nection Configuration Identi-fier) references must be unique within all WBTS objects

COCO OBJECT IS BEING USED BY SOME WBTS

WBTS_CM_0003 WBTS Create/Modify WBTS - IPBasedRouteIdIub reference must be unique within all WBTS objects

THE IP BASED ROUTE ID NOT UNIQUE UNDER WBTS OBJECT.

WBTS_CM_0004 WBTS Create/Modify If the referred COCO object exists, then WBTS - COCOId and WBTS - ATMInterfaceID / VPI / VCI must be the same as given for COCO, if they are defined.

MISMATCH BETWEEN COCO ID AND C-NBAP PARAMS IN WBTS AND COCO-OBJECT

WBTS_CM_0005 WBTS Create/Modify When IubTransportMedia is not ATM, IP Subnet id must be defined

IUBTRANSPORTMEDIA IS NOT ATM, IPBASE-DROUTEIDIUB MUST BE DEFINED.

WBTS_CM_0006 WBTS Create/Modify WBTS- AutoConnSiteID must be unique for every BTS.

WBTS- AUTOCONNSITEID SHOULD BE UNIQUE FOR EVERY BTS.

WBTS_CM_0007 WBTS Create/Modify WBTS- AutoConnHWID must be unique for every BTS.

WBTS- AUTOCONNHWID SHOULD BE UNIQUE FOR EVERY BTS.

Table 34 WBTS consistency checking rules

64 DN0934038




WBTS_CM_0008 WBTS Create/Modify WBTS-BroadcastSIB15 cannot be enabled when the RNC-LCS functionality is not enabled.

WBTS-BROADCASTSIB15 CAN NOT BE USED WHEN RNC-LCSFUNCTIONALITY IS NOT ENABLED.

WBTS_CM_0009 WBTS Create/Modify WBTS-BroadcastSIB15 cannot be enabled when WSMLC-LCSInterfaceOption is not IUPC.

WBTS-BROADCASTSIB15 CAN NOT BE ENABLED WHEN WSMLC-LCSINTER-FACEOPTION IS NOT IUPC.

WBTS_CM_0010 WBTS Create/Modify WBTS-BroadcastSIB15.2 and WBTS-BroadcastSIB15.3 can be enabled only when WBTS-BroadcastSIB15 is enabled

WBTS-BROADCASTSIB15.2 OR WBTS-BROADCASTSIB15.3 CON-FLICTED WITH WBTS-BROADCASTSIB15.

WBTS_CM_0011 WBTS Create/Modify WBTS IPBasedRouteIdIub2 must be unique for all WBTS.

WBTS IPBASEDROUTEIDIUB2 MUST BE UNIQUE FOR ALL WBTS

WBTS_CM_0012 WBTS Create/Modify WBTS must not be connected to a COCO or an IPNB object when WBTS-NBAPCom-mMode is modified.

WBTS MUST NOT BE CON-NECTED TO COCO OR IPNB OBJECT WHEN WBTS-NBAPCOMMMODE IS MODI-FIED.

WBTS_CM_0013 WBTS Create/Modify WBTS IPBasedRouteIdIub must be defined when WBTS IPBasedRouteIdIub2 has some defined value.

WBTS IPBASE-DROUTEIDIUB MUST BE DEFINED WHEN WBTS IPBASEDROUTEIDIUB2 HAS SOME DEFINED VALUE.

WBTS_CM_0014 WBTS Create/Modify COCOId or ATMIf/VPI/VCI triplet and IPNBId cannot both be defined.

COCOID OR ATMIF/VPI/VCI TRIPLET AND IPNBID CAN NOT BE BOTH DEFINED.

WBTS_CM_0015 WBTS Create/Modify Once the COCOId or ATMIf/VPI/VCI triplet is defined, then IubTransportMe-dia may not contain the value "IPIub"; Once the IPNBId is defined then IubTransportMe-dia may only contain the value "IPIub".

COCO DEFINED IUBTRANS-PORTMEDIA MAY NOT CONTAIN IPIUB; IPNB DEFINED IUBTRANSPORT-MEDIA MAY ONLY CONTAIN IPIUB.

WBTS_CM_0016 WBTS Create/Modify For the parameter IubTrans-portMedia, if NRT DCH traffic is configured over IP, all other NRT traffic should be config-ured over IP.

IF NRT DCH TRAFFIC IS CONFIGURED OVER IP, ALL OTHER NRT TRAFFICS SHOULD BE CONFIGURED OVER IP.


Object type

Operation type


Table 34 WBTS consistency checking rules (Cont.)

DN0934038 65




WBTS_CM_0017 WBTS Create/Modify WBTS-HSDPA14MbpsPerUser user can be enabled only when the CDSP-DH hardware is present in upgrade mode

WBTS-HSDPA14MBPSPERUSER USER CAN BE ENABLED ONLY WHEN THE HARDWARE OF CDSP-DH IS PRESENT IN UPGRADE MODE

WBTS_CM_0018 WBTS Create/Modify The value of DelayThreshold-Min always has to be lower than the value of DelayThresh-oldMid, unless DelayThresh-oldMax has the value HSUPA CC mechanism disabled.

INTERDEPENDENCE BETWEEN DELAYTHRESH-OLDMIN, DELAYTHRESH-OLDMID AND DELAYTHRESHOLDMAX ERROR

WBTS_CM_0019 WBTS Create/Modify The value of DelayThresholdMin2msTTI always has to be lower than the value of DelayThresholdMid2msTTI.

THE VALUE OF DELAYTHRESHOLDMIN2MSTTI IS NOT LESS THAN THE VALUE OF DELAYTHRESHOLDMID2MSTTI

WBTS_CM_0020 WBTS Create/Modify WBTS- DelayThresholdMin should be less than WBTS- DelayThresholdMid.

WBTS-DELAYTHRESHOLD-MIN SHOULD BE LESS THAN WBTS-DELAYTHRESHOLD-MID

WBTS_CM_0021 WBTS Create/Modify DelayThresholdMin2msTTI should be less than DelayThresholdMid2msTTI and DelayThresholdMid2msTTI should be less than DelayThresholdMax2msTTI.

DEPENDENCY AMONG WBTS PARAMETERS DELAYTHRESHOLDMIN2MSTTI,DELAYTHRESHOLDMID2MSTTI AND DELAYTHRESHOLDMAX2MSTTI

WBTS_CM_0022 WBTS Create/Modify The maximum number of WBTSs that have HSDPA enabled WCELs exceeded.

MAXIMUM NUMBER OF HSDPA WBTSS EXCEEDED

WBTS_CM_0023 WBTS Create/Modify The number of HSUPA 3 Users Per BTS enabled BTS exceeds the capacity limit.

THE NUMBER OF HSUPA 3 USERS PER BTS ENABLED BTS EXCEEDS THE CAPACITY LIMIT




Object type

Operation type



66 DN0934038








WBTS_CM_0027 WBTS Create/Modify The maximum number of HSDPA congestion control enabled WBTS exceeded.

MAXIMUM NUMBER OF HSDPA CONGESTION CONTROL ENABLED WBTS EXCEEDED

WBTS_CM_0028 WBTS Create/Modify The number of HSDPA 64 Users Per Cell enabled BTS exceeds the capacity limit.

THE NUMBER OF HSDPA 64 USERS PER CELL ENABLED BTS EXCEEDS THE CAPACITY LIMIT

WBTS_CM_0029 WBTS Create/Modify The number of HSDPA 14Mbps per user enabled WBTS exceeds the capacity limit set by the license.

THE NUMBER OF HSDPA 14MBPS PER USER ENABLED WBTS EXCEEDS THE CAPACITY LIMIT

WBTS_CM_0030 WBTS Create/Modify The number of HSPA multi NRT RAB enabled BTS exceeds the capacity limit set by the license.

THE NUMBER OF HSPA MULTI NRT RAB ENABLED BTS EXCEEDS THE CAPACITY LIMIT

WBTS_CM_0031 WBTS Create/Modify The number of IP Based Iub enabled WBTS exceeds the capacity of license IP Based Iub.

THE NUMBER OF IP BASED IUB ENABLED WBTS EXCEEDS THE CAPACITY OF LICENSE IP BASED IUB.

WBTS_CM_0032 WBTS Create/Modify The number of Dual Iub enabled WBTS exceeds the capacity of license Dual Iub.

THE NUMBER OF DUAL IUB ENABLED WBTS EXCEEDS THE DUAL IUB CAPACITY LIMIT

WBTS_CM_0033 WBTS Create/Modify The number of QoS Aware HSPA Scheduling enabled BTS exceeds the licensed capacity.

THE NUMBER OF QOS AWARE HSPA SCHEDULING ENABLED BTS EXCEEDS THE LICENSED CAPACITY

WBTS_CM_0034 WBTS Create/Modify The number of HSPA with Streaming QoS Support enabled BTS exceeds the licensed capacity.

THE NUMBER OF HSPA WITH STREAMING QOS SUPPORT ENABLED BTS EXCEEDS THE LICENSED CAPACITY


Object type

Operation type



DN0934038 67




WBTS_CM_0035 WBTS Create/Modify The count of Iub Transport QoS-enabled WBTS exceeds the license Iub Transport QoS capacity limit.

THE COUNT OF IUB TRANS-PORT QOS-ENABLED WBTS EXCEEDS THE LICENSE IUB TRANSPORT QOS CAPACITY LIMIT

WBTS_CM_0036 WBTS Create/Modify HSDPA 14Mbps per user can be enabled only when HSDPA dynamic resource allocation is enabled. HSDPA dynamic resource allocation cannot be disabled when HSDPA 14Mbps per user is enabled.


WBTS_CM_0037 WBTS Create/Modify WCEL-DCellHSDPAEnabled can be enabled only when WBTS-HSDPA14MbpsPerUser is enabled.

WCEL-DCELLHSDPAEN-ABLED CAN BE ENABLED ONLY WHEN WBTS- HSDPA14MBPSPERUSER IS ENABLED

WBTS_CM_0038 WBTS Create/Modify WBTS-ICREnabled cannot be set to Enabled if RNC-MOC-NEnabled is Enabled.

WBTS-ICRENABLED CAN BE ENABLED ONLY WHEN RNC-MOCNENABLED IS DISABLED

WBTS_CM_0039 WBTS Create/Modify WBTS-ICREnabled cannot be set to Enabled if MORAN is enabled and multiple PLMN IDs exist for the host operator in IUO objects.

WBTS-ICRENABLED CAN BE ENABLED ONLY WHEN MORAN IS DISABLED

WBTS_CM_0040 WBTS Create/Modify WBTS-ICR Enabled is not allowed if no IUO object exists.

WBTS-ICRENABLED CAN BE ENABLED ONLY WHEN IUO OBJECT EXIST

WBTS_CM_0041 WBTS Create/Modify WBTS-ICR Enabled is not allowed if IUO-ICROpID is undefined in any IUO object.

IUO-ICR OPERATOR ID NOT DEFINED FOR ONE OR MORE IUO OBJECTS

WBTS_CM_0042 WBTS Create/Modify WBTS-ICR Enabled cannot be set as enabled if RNC-HostOpId is not a defined IUO-ICROpId.


WBTS_CM_0043 WBTS Create/Modify WBTS-R99OperIdWeightPair –R99OperatorId, if defined, must be unique within the WBTS.

WBTS-R99ICROPERATORID MUST BE UNIQUE WITHIN WBTS OBJECT


Object type

Operation type



68 DN0934038




WBTS_CM_0044 WBTS Create/Modify WBTS-R99OperIdWeightPair –R99OperatorId, if defined, must match one of the IUO-ICROperatorId.

REL99OPERATORID SHALL MATCH WITH ATLEAST ONE IUO-ICROPEATORID

WBTS_CM_0045 WBTS Create/Modify Sum of all WBTS-R99OperIdWeightPair –R99OpWt (where R99OpId is also defined) must be either 0 or 100.

SUM OF R99OPERTWEIGHT FOR ALL THE OPERATORS MUST BE EITHER 0 OR 100

WBTS_CM_0046 WBTS Create/Modify WBTS-ICREnabled cannot be set to Enabled if DCHSD-PAEnabled is Enabled for any WCEL under this cell.

WBTS-ICRENBABLED CAN BE ENABLED ONLY WHEN WCEL-DCHSDPA IS DISABLED FOR ALL WCELS

WBTS_CM_0047 WBTS Create/Modify WBTS-ICREnabled cannot be set to Enabled if IMSIBasedHO is not set to “allowed(1)” that is, “1” for any WCEL under this cell.

IMSIBASEDGSMHO MUST BE ENABLED FOR ALL THE WCELS UNDER BTS HAVING WBTS-ICREN-ABLED AS ENABLED

WBTS_CM_0048 WBTS Create/Modify If WBTS-HSDPAOperId-WeightPair –HSDPAOperato-rId is defined, it must be unique within WBTS.

WBTS-HSDPAICROPERA-TORID MUST BE UNIQUE WITHIN WBTS OBJECT

WBTS_CM_0049 WBTS Create/Modify If WBTS-HSDPAOperId-WeightPair –HSDPAOperato-rId is defined, it must match at least one IUO-ICROperatorId.

WBTS-HSDPAICROPERA-TORID MUST MATCH AT LEAST ONE IUO-ICROPERA-TORID

WBTS_CM_0050 WBTS Create/Modify WBTS-HSDPAOperIdWeight-Pair -HSDPAOperatorWt should be given only if WBTS-WBTS-HSDPAOperIdWeight-Pair-HSDPAOperatorId is defined.

WBTS-HSDPAICROPERA-TORID MUST BE DEFINED IF WBTS-HSDPAOPWT IS DEFINED

WBTS_CM_0051 WBTS Create/Modify Sum of WBTS-HSDPAIur-Weight WBTS-HSDPAOperId-WeightPair -HSDPAOperatorWt must be either 0 or 100.

SUM OF WBTS-HSDPAI-URWT AND ALL WBTS-HSD-PAOPWTS MUST BE EITHER 0 OR 100

WBTS_D_0001 WBTS Delete The WBTS cannot be deleted if some WCELs are still under it.

IUBTRANSPORTMEDIA IS NOT ATM, IPBASE-DROUTEIDIUB MUST BE DEFINED.


Object type

Operation type



DN0934038 69




WBTS_M_0001 WBTS Modify WBTS - ATMInterfaceID (ATM interface identifier) / VPI / VCI and WBTS - COCOId (Con-nection Configuration Identi-fier) modification requires WCEL object locking when the COCO is related to the WBTS

OPERATION REQUIRES THAT ALL WCELS UNDER THE WBTS MUST BE LOCKED

WBTS_M_0002 WBTS Modify DedicatedMeasReportPeriod or RRMULDCHActivityFactor or IubTransportMedia or Dedi-MeasRepPeriodCSdata or DediMeasRepPeriodPSdata requires WCEL object locking to all WCELS related to the WBTS if the WBTS is con-nected with COCO or IPNB


WBTS_M_0003 WBTS Modify IPNBId or IPBasedRouteIdIub requires WCEL object locking to all WCELS related to the WBTS, if the WBTS is con-nected with IPNB


WBTS_M_0004 WBTS Modify If IubTransportMedia is not ATM and WBTS is connected with COCO, IPBase-dRouteIdIub modification requires WCEL object locking.


WBTS_M_0005 WBTS Modify MaxNumberEDCHLCG must be higher than the value of the parameter WCEL-NumberED-CHReservedSHOBranchAddi-tions.

NUMBEREDCHRESERVED-SHOBRANCHADDITIONS GREATER THAN MAXNUM-BEREDCHLCG OR MAX-NUMBEREDCHCELL

WBTS_M_0007 WBTS Modify The window size for interfer-ence measurement to start LHOs must be equal to or greater than the Radio Resource Indication Period in the WBTS cell.

LHOWINSIZEONINTERFER-ENCE HAS TO BE EQUAL TO OR GREATER THAN RRIND-PERIOD IN WBTS CELL

WBTS_M_0008 WBTS Modify WBTS-BTSFallbackEnabled modification requires object locking.



Object type

Operation type



70 DN0934038




WBTS_M_0009 WBTS Modify WBTS-IubTransportFallback-Enabled modification requires object locking.


WBTS_M_0010 WBTS Modify The count of CCH Setup-enabled WCELs cannot exceed the license CCHSetup capacity limit.

THE COUNT OF CCH SETUP ENABLED WCEL'S EXCEEDS THE LICENSE CCHSETUP CAPACITY LIMIT.

WBTS_M_0011 WBTS Modify WBTS-NBAPCommMode modification requires object locking.


WBTS_M_0012 WBTS Modify WBTS-HSDPAIurWeight can have a value greater than 0 only if for any WCEL, WCEL-HSPAQosEnabled is set to a value greater than 0.

AT LEAST ONE WCEL-HSPAQOS MUST BE GREATER THAN 0 FOR NONZERO WBTS-HSDPAI-URWT

WBTS_M_0013 WBTS Modify If WBTS-HSDPAOperator-WeightPair-HSDPAOperato-rId is defined then HSPAQosEnabled must be set to a value greater than 0 in at least one WCEL under this WBTS.

IF WBTS-HSDPAOPWTID IS DEFINED THEN WCEL-HSPAQOSENABLED IN AT LEAST ONE WCEL OF WBTS MUST BE GREATER THAN 0

WBTS_M_0014 WBTS Modify WBTS-HSDPAOperIdWeight-Pair -HSDPAOperatorWt can be greater than 0 only if for any WCEL, WCEL-HSPAQosEn-abled is set to a value greater than 0.

AT LEAST ONE WCEL-HSPAQOS MUST BE GREATER THAN 0 FOR NONZERO WBTS-HSD-PAOPWT


Object type

Operation type



DN0934038 71


WCEL consistency checking rules

Id:0900d805808be29fConfidential

35 WCEL consistency checking rulesThe following table lists the WCEL consistency checking rules.


Object type

Operation type


WCEL_C_0001 WCEL Create The maximum number of WCEL objects in the RNW database for RNC196, RNC450, and RNC2600 is 1152, 1800, and 2800 respec-tively

MAXIMUM NUMBER OF WCELS EXCEEDED

WCEL_C_0002 WCEL Create Cell identifier (cid) must be unique under the RNCs. There is some other cell with the same id in the same RNC.

CELL IDENTIFIER IS NOT UNIQUE IN THE RNC

WCEL_C_0003 WCEL Create If CommonPLMNId/Multiple-PLMNListIncluded is defined, PS Core Network Identity must not be defined for WCEL.

IF COMMONPLMNID/MULTI-PLEPLMNLISTINCLUDED IS DEFINED, CS CORE NETWORK IDENTITY SHALL NOT BE DEFINED FOR WCEL.

WCEL_C_0004 WCEL Create If Common PLMN id is config-ured, PS Core Network Identity must not be defined for WCEL.

IF COMMON PLMN ID IS CONFIGURED, PS CORE NETWORK IDENTITY SHALL NOT BE DEFINED FOR WCEL.

WCEL_CM_0001 WCEL Create/Modify The WRAB object could not be found in the Radio Network Database.

WRAB NOT FOUND

WCEL_CM_0003 WCEL Create/Modify RtFmcsIdentifier and RtFmcsI-dentifier (RT/NRT FMCS Iden-tifier) must be defined.

FMCS NOT FOUND

WCEL_CM_0004 WCEL Create/Modify If RtFmciIdentifier (RT FMCI Identifier) is defined, NrtFmciI-dentifier (NRT FMCI Identifier) must also be defined.

IF RT FMCI IS GIVEN, ALSO NRT FMCI IS NEEDED

WCEL_CM_0005 WCEL Create/Modify If NrtFmciIdentifier (NRT FMCI Identifier) is defined, RtFmciI-dentifier (RT FMCI Identifier) must also be defined.

IF NRT FMCI IS GIVEN, ALSO RT FMCI IS NEEDED

WCEL_CM_0006 WCEL Create/Modify If ADJI is defined, RtFmciIden-tifier (RT FMCI Identifier) must also be defined.

FMCI ID NOT DEFINED FOR THE WCEL

Table 35 WCEL consistency checking rules

72 DN0934038




WCEL_CM_0007 WCEL Create/Modify If RtFmcgIdentifier (RT FMCG Identifier) is defined, NrtFmcgI-dentifier (NRT FMCG Identi-fier) must also be defined.

IF RT FMCG IS GIVEN, ALSO NRT FMCG IS NEEDED

WCEL_CM_0008 WCEL Create/Modify If NrtFmcgIdentifier (NRT FMCG Identifier) is defined, RtFmcgIdentifier (RT FMCG Identifier) must also be defined.

IF NRT FMCG IS GIVEN, ALSO RT FMCG IS NEEDED

WCEL_CM_0009 WCEL Create/Modify If ADJG is defined, RtFmcgI-dentifier (RT FMCG Identifier) must be defined.

FMCG ID NOT DEFINED FOR THE WCEL

WCEL_CM_0010 WCEL Create/Modify The value of FachLoadMargin-CCH must be lower than the value of FachLoadThreshold-CCH if both are not 0

WCEL-FACHLOADMARGIN-CCH MUST BE LESS THAN WCEL-FACHLOADTHRESH-OLDCCH

WCEL_CM_0011 WCEL Create/Modify The value of RachLoadMargin-CCH must be lower than the value of RachLoadThreshold-CCH if both are not 0

WCEL-RACHLOADMARGIN-CCH MUST BE LESS THAN WCEL-RACHLOADTHRESH-OLDCCH

WCEL_CM_0012 WCEL Create/Modify InitialBitRateDL should not be higher than the value of MaxBi-tRateDLPSNRT.


WCEL_CM_0013 WCEL Create/Modify InitialBitRateDL should not be lower than the value of MinAl-lowedBitRateDL.


WCEL_CM_0014 WCEL Create/Modify InitialBitRateUL should not be higher than the value of MaxBi-tRateULPSNRT.


WCEL_CM_0015 WCEL Create/Modify InitialBitRateUL should not be lower than the value of MinAl-lowedBitRateUL.


WCEL_CM_0016 WCEL Create/Modify MaxBitRateDLPSNRT should not be lower than the value of MinAllowedBitRateDL


WCEL_CM_0017 WCEL Create/Modify MaxBitRateULPSNRT should not be lower than the value of MinAllowedBitRateUL


WCEL_CM_0018 WCEL Create/Modify MinAllowedBitRateDL should not be higher than the value of MaxBitRateDLPSNRT



Object type

Operation type


Table 35 WCEL consistency checking rules (Cont.)

DN0934038 73




WCEL_CM_0019 WCEL Create/Modify MinAllowedBitRateUL should not be higher than the value of MaxBitRateULPSNRT


WCEL_CM_0020 WCEL Create/Modify The RACH_Tx_NB01max parameter value must always be higher than the value of the RACH_Tx_NB01min parame-ter


WCEL_CM_0022 WCEL Create/Modify If the maximum cell range (CellRange) is greater than 10 km, AICH Transmission Timing is 1 and Rx Diversity Indicator is 1. If AICH Trans-mission Timing has the value 0, or if four antennas are used (Rx Diversity Indicator = 2), the maximum value can be 10 km.

CELL RANGE OF WCEL IS INCORRECT

WCEL_CM_0023 WCEL Create/Modify The value of LHOWinSizeON-Interference must be equal to or greater than RRIndPeriod if it is not 0 and NBAPCom-mMode is not NB/RSXXX

LHOWINSIZEONINTERFER-ENCE HAS TO BE EQUAL TO OR GREATER THAN RRIND-PERIOD IN WBTS CELL

WCEL_CM_0024 WCEL Create/Modify The value of LHOWinSizeON-Interference should be equal to or greater than PrxTotalRe-portPeriod and PtxTotalRe-portPeriod if it is not 0 and NBAPCommMode is NB/RSXXX

LHOWINSIZEONINTERFER-ENCE CANNOT SHORTER THAN PRX AND PTXTOTAL-REPORTPERIOD IN NB/RSXXX CELL

WCEL_CM_0025 WCEL Create/Modify UARFCN (UTRAN Absolute Radio Frequency Number) and Downlink Primary Scrambling Code must together be unique under WCELs parent WBTS.

WCELS UARFCN AND DL_PRI_SCR_CODE PAIR MUST BE UNIQUE UNDER WBTS

WCEL_CM_0026 WCEL Create/Modify If WBTS-NBAPCommMode has the value (NB/RSxxx), the value 1 of WCEL-AICHTra-Time must be used

IF WBTS-NBAPCOMMMODE IS SET TO NB/RSXXX, WCEL-AICHTRATIME MUST BE SET TO ONE

WCEL_CM_0027 WCEL Create/Modify If wbts-nbapcommmode is set to ultrasite bts/flexibts/picobts, wcel-cellrange must not be set to zero.

WCEL-CELLRANGE MUST BE DEFINED IF WBTS-NBAPCOMMMODE IS SET TO ULTRASITE BTS / FLEXIBTS / PICOBTS


Object type

Operation type



74 DN0934038




WCEL_CM_0028 WCEL Create/Modify WCEL-HSUPA2MSTTIEnabled can be enabled only when a CDSP-DH card exists

WCEL-HSUPA2MSTTIENABLED CAN BE ENABLED ONLY WHEN CSDSP-DH CARD EXIST

WCEL_CM_0030 WCEL Create/Modify WCEL - WCELGlobalCNid - WCELPLMNid (PLMN identity) must be defined

PLMN ID NOT DEFINED

WCEL_CM_0033 WCEL Create/Modify If this DirectedRRCForHSD-PALayerEnhanc is disabled, DirectedRRCEnabled and DirectedRRCForHSDPALay-erEnabled cannot be enabled simultaneously.

WCEL-DIRECTEDRRCEN-ABLED AND WCEL-DIRECT-EDRRCFORHSDPALAYERENABLED CANNOT BE ENABLED SIMULTANE-OUSLY

WCEL_CM_0034 WCEL Create/Modify If WCEL - NbrOfSCCPCHs (Number of SCCPCHs) is 3 (the SAB feature is active), SACB (Service Area Code for SAB) must be defined.

SAC_B MUST BE DEFINED IF SAB ACTIVE

WCEL_CM_0035 WCEL Create/Modify CTCH_CAPA_CBS_MSG must be given if SAB (Service area broadcast) is active.

CTCH_CAPA_CBS_MSG MUST BE DEFINED IF SAB ACTIVE

WCEL_CM_0036 WCEL Create/Modify If WCEL - NbrOfSCCPCHs (Number of SCCPCHs) is 3 (the SAB feature is active), KforCTCH must be defined.

K_CTCH MUST BE DEFINED IF SAB ACTIVE

WCEL_CM_0037 WCEL Create/Modify If WCEL - NbrOfSCCPCHs (Number of SCCPCHs) is 3 (the SAB feature is active), NforCTCH must be defined.

N_CTCH MUST BE DEFINED IF SAB ACTIVE

WCEL_CM_0038 WCEL Create/Modify If WCEL - NbrOfSCCPCHs (Number of SCCPCHs) is 3 (the SAB feature is active), RNC - CBCList - CBCItem (CBC Item) must be defined

CBC (CELL BROADCAST CENTER) MUST BE DEFINED IF SAB (SERVICE AREA BROADCAST) IN USE

WCEL_CM_0039 WCEL Create/Modify WCEL - SACB (Service Area Code for SAB) must be unique in the RNC

SAC_B PARAMETER MUST BE UNIQUE IN RNC

WCEL_CM_0040 WCEL Create/Modify SectorID: More than two cells can belong to the same sector if DirectedRRCForHSDPALay-erEnhanc is enabled.

IF DIRECTEDRRCFORHSD-PALAYERENHANC IS DIS-ABLED, THERE CANNOT BE MORE THAN TWO LAYERS


Object type

Operation type



DN0934038 75




WCEL_CM_0041 WCEL Create/Modify Two or more cells can belong to the same sector if the follow-ing parameters are identical for these cells: PtxPrimaryCPICH, CPICHtoRefRABoffset, MCC, MNC.

ILLEGAL SECTOR ID FOR WCEL UNDER THIS WBTS

WCEL_CM_0042 WCEL Create/Modify A WCEL object cannot be created or modified with a relation to a CMOB that does not exist. The relation of WCEL to CMOB is defined with the parameters RNARGroupId, CSGroupId, and PSGroupId.

CMOB NOT FOUND

WCEL_CM_0043 WCEL Create/Modify The WCEL parameter RNAR-GroupId can only contain either the value Not defined or an identifier for CMOB whose type is RNAR

CMOB TYPE AND USAGE DO NOT MATCH IN WCEL

WCEL_CM_0044 WCEL Create/Modify WCEL parameter CSGroupId can only contain either the value Not defined or an identi-fier for CMOB whose type is CS-DSAC


WCEL_CM_0045 WCEL Create/Modify WCEL parameter PSGroupId can only contain either the value Not defined or an identi-fier for CMOB whose type is PS-DSAC


WCEL_CM_0046 WCEL Create/Modify AMRUnderTxTotal must be lower than AMRTargetTxTotal

AMRUNDERTXTOTAL MUST BE SMALLER THAN AMR-TARGETTXTOTAL

WCEL_CM_0047 WCEL Create/Modify AMRTargetTXtotal must be lower than AMROverTxtotal

AMRTARGETTXTOTAL MUST BE SMALLER THAN AMROVERTXTOTAL

WCEL_CM_0048 WCEL Create/Modify WCEL-AMROverTxTotal must be greater than WCEL-AMRUnderTxTotal.

WCEL-AMROVERTXTOTAL MUST BE GREATER THAN WCEL-AMRUNDERTXTO-TAL

WCEL_CM_0049 WCEL Create/Modify AMRUnderTxNC must be lower than AMRTargetTxNC

AMRUNDERTXNC MUST BE SMALLER THAN AMRTAR-GETTXNC


Object type

Operation type



76 DN0934038




WCEL_CM_0050 WCEL Create/Modify AMRTargetTxNC must be lower than AMROverTxNC

AMRTARGETTXNC MUST BE SMALLER THAN AMROVERTXNC

WCEL_CM_0051 WCEL Create/Modify AMRUnderTxNC must be lower than AMROverTxNC

WCEL-AMRUNDERTXNC MUST BE SMALLER THAN WCEL-AMROVERTXNC.

WCEL_CM_0052 WCEL Create/Modify AMRUnderTxNonHSPA must be lower than AMRTargetTx-NonHSPA

AMRUNDERTXNONHSPA MUST BE SMALLER THAN AMRTARGETTXNONHSPA

WCEL_CM_0053 WCEL Create/Modify AMRTargetTxNonHSPA must be lower than AMROverTx-NonHSPA

AMRTARGETTXNONHSPA MUST BE SMALLER THAN AMROVERTXNONHSPA

WCEL_CM_0054 WCEL Create/Modify AMRUnderTxNonHSPA must be lower than AMROverTx-NonHSPA

WCEL-AMROVERTX-NONHSPA MUST BE GREATER THAN WCEL-AMRUNDERTXNONHSPA

WCEL_CM_0055 WCEL Create/Modify AMRUnderSC must be lower than AMRTargetSC

AMRUNDERSC MUST BE SMALLER THAN AMRTAR-GETSC

WCEL_CM_0056 WCEL Create/Modify AMRTargetSC must be lower than AMROverSC

AMRTARGETSC MUST BE SMALLER THAN AMROVERSC

WCEL_CM_0057 WCEL Create/Modify AMRUnderSC must be lower than AMROverSC

WCEL-AMROVERSC MUST BE GREATER THAN WCEL-AMRUNDERSC

WCEL_CM_0058 WCEL Create/Modify AMRUnderTransmission must be lower than AMRTar-getTransmission

AMRUNDERTRANSMIS-SION MUST BE SMALLER THAN AMRTARGETTRANS-MISSION

WCEL_CM_0059 WCEL Create/Modify AMRTargetTransmission must be lower than AMROverTrans-mission

AMRTARGETTRANSMIS-SION MUST BE SMALLER THAN AMROVERTRANS-MISSION

WCEL_CM_0060 WCEL Create/Modify AMRUnderTransmission must be lower than AMROverTrans-mission

WCEL-AMROVERTRANS-MISSION MUST BE GREATER THAN WCEL-AMRUNDERTRANSMISSION

WCEL_CM_0061 WCEL Create/Modify PtxCellMax must be greater than or equal to PtxMaxHS-DPA

WCEL-PTXCELLMAX MUST BE GREATER THAN OR EQUAL TO WCEL-PTX-MAXHSDPA


Object type

Operation type



DN0934038 77




WCEL_CM_0062 WCEL Create/Modify RachTxNb01Max must be greater than or equal to RachTxNb01Min

WCEL-RACH_TX_NB01MIN PARAMETER VALUE MUST BE LOWER THAN THE VALUE OF WCEL-RACH_TX_NB01MAX PARAMETER

WCEL_CM_0063 WCEL Create/Modify PtxTargetPSMax must be greater than or equal to Ptx-TargetPSMin

WCEL- PTXTARGETPSMAX MUST BE GREATER THAN OR EQUAL TO THE WCEL- PTXTARGETPSMIN

WCEL_CM_0064 WCEL Create/Modify PtxFDPCHMax must not be greater than PtxFDPCHMin

WCEL-PTXFDPCHMAX PARAMETER MUST NOT BE GREATER THAN WCEL-PTXFDPCHMIN PARAME-TER

WCEL_CM_0065 WCEL Create/Modify FDPCHEnabled can be Enabled only if HSUPAEn-abled is Enabled

FDPCHENABLED CAN BE ENABLED ONLY IF HSU-PAENABLE IS ENABLED

WCEL_CM_0066 WCEL Create/Modify FDPCHEnabled can be Enabled only if the HSPAQoSEnabled value is 1 or higher

FDPCHENABLED CAN BE ENABLED ONLY IF QOS PRI-ORITIZATION IS USED WITH THE PARAMETER HSPAQOSENABLED

WCEL_CM_0067 WCEL Create/Modify HSUPAEnabled can be Enabled only when HSDPA-Mobility is Enabled

HSUPAEnabled CAN BE ENABLED IF HSDPAMobility IS ENABLED;HSDPAMobility CAN BE DISABLED IF NO WCEL USE HSUPA

WCEL_CM_0069 WCEL Create/Modify If the HSDPA-enabled param-eter value is Enabled, hsdpa_fmcs_id must be defined

HSDPA FMCS MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL

WCEL_CM_0070 WCEL Create/Modify If the HSDPA enabled parame-ter value is Enabled, and AMR-WithHSDSCH is Enabled, RT_hsdpa_fmcs_id must be defined.

RT HSDPA FMCS IDENTI-FIER MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL

WCEL_CM_0071 WCEL Create/Modify If HSDPA and HSDPA Dynamic Resource Allocation are Enabled, PtxTargetPSMax must be lower than or equal to PtxTarget.



Object type

Operation type



78 DN0934038




WCEL_CM_0072 WCEL Create/Modify If HSDPA and HSDPA Dynamic Resource Allocation are Enabled, PtxTargetPSMax must be greater than or equal to PtxTargetPSMin.


WCEL_CM_0073 WCEL Create/Modify If the HSDPA enabled parame-ter value is Enabled, PtxTar-getHSDPA must be defined

PARAMETER PTX_TARGET_HSDPA MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL

WCEL_CM_0074 WCEL Create/Modify If the HSDPA enabled parame-ter value is Enabled, Ptx-MaxHSDPA must be defined

PARAMETER PTX_MAX_HSDPA MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL

WCEL_CM_0075 WCEL Create/Modify If WCEL - HSDPA64UsersEnabled (HSDPA 64 users enabled) is Enabled, HSDPAenabled (HSDPA enabled) must be Enabled

HSDPA 64 USERS ENABLED CAN BE ENABLED ONLY WHEN HSDPA ENABLED IS ENABLED.

WCEL_CM_0077 WCEL Create/Modify The following HSDPA 64 user feature related parameters request object locking when modified: HSDPA64UsersEnabled


WCEL_CM_0078 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, HSD-PAEnabled must be Enabled

INTERDEPENDENCE BETWEEN HSUPA ENABLED AND HSDPA ENABLED ERROR

WCEL_CM_0079 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) and AMRWith-HSDSCH are enabled, RTWithHSDPAFmcsIdentifier must be defined.

HSPA FMCS IDENTIFIER FOR AMR MULTI-SERVICE NOT DEFINED

WCEL_CM_0080 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, HSDPA-DynamicResourceAllocation must be Enabled

HSDPA DYNAMIC RESOURCE ALLOCATION NOT ENABLED

WCEL_CM_0081 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, the HSU-PAXUSERSENABLED value Disabled is not allowed

HSUPA ENABLED CANNOT BE ENABLED IF HSUPA X USERS ENABLED IS NOT ENABLED.


Object type

Operation type



DN0934038 79




WCEL_CM_0082 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, hsdpa_fmcs_id must be defined

HSPA FMCS IDENTIFIER NOT DEFINED

WCEL_CM_0083 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, PrxTar-getPSMax must be lower than or equal to the PrxTarget.

PRXTARGET LESS THAN PRXTARGETPSMAX

WCEL_CM_0084 WCEL Create/Modify PrxLoadMarginEDCH must be lower than or equal to the value of the PrxMaxTargetBTS

INTERFERENCE MARGIN FOR MIN EDCH LOAD GREATER THAN MAX TARGET RECEIVED WIDE BAND POWER

WCEL_CM_0085 WCEL Create/Modify PrxTargetPSMax must be greater than or equal to Prx-TargetPSMin.

MIN PS TARGET INTERFER-ENCE SHARING BIGGER THAN MAX PS TARGET INTERFERENCE SHARING

WCEL_CM_0086 WCEL Create/Modify PrxLoadMarginDCH must be lower than or equal to the value of PrxLoadMarginMaxDCH.

INTERFERENCE MARGIN FOR THE MIN UL DCH LOAD GREATER THAN THE MAX VALUE

WCEL_CM_0087 WCEL Create/Modify The value of NumberED-CHReservedSHOBranchAddi-tions must be lower than the values of MaxNumberEDCH-Cell and MaxNumberED-CHLCG

NUMBEREDCHRESERVED-SHOBRANCHADDITIONS GREATER THAN MAXNUM-BEREDCHLCG OR MAX-NUMBEREDCHCELL

WCEL_CM_0088 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, Num-berEDCHReservedSHO-BranchAdditions must be lower than the value of HSU-PAXUsersEnabled.

IF HSUPA IS ENABLED, NUMBEREDCHRESERVED-SHOBRANCHADDITIONS MUST BE LOWER THAN HSUPAXUSERSENABLED

WCEL_CM_0089 WCEL Create/Modify If HSUPA is activated, it must be activated in all cells that use the same frequency (UARFCN) in the same BTS.

THE HSUPA STATE OF WCELS WITH SAME UARFCN INCONSISTENCY

WCEL_CM_0090 WCEL Create/Modify If HSUPA is deactivated, it must be deactivated in all cells that use the same frequency (UARFCN) in the same BTS.



Object type

Operation type



80 DN0934038




WCEL_CM_0091 WCEL Create/Modify The following HSUPA feature related parameters request object locking when modified: HSUPAEnabled, PrxLoadMar-ginEDCH, SIRDPCCHOffset-EDPCH, MaxTotalUplinkSymbolRate, TargetNSEDCHToTotalED-CHPR


WCEL_CM_0092 WCEL Create/Modify HSUPA2MSTTIEnabled can be set to Enabled only if HSUPA is enabled in the cell using the RNP parameter HSUPAEnabled

HSUPA2MSTTIEnabled CAN BE SET TO ENABLED ONLY IF HSUPAEnabled IS ENABLED

WCEL_CM_0093 WCEL Create/Modify MaxTotalUplinkSymbolRate can be set to 3 (5760kbps, 2*SF2+2*SF4) only if HSUPA 2ms TTI is enabled in the cell using the RNP parameter

MaxTotalUplinkSymbolRate CAN BE SET TO 5760kbps ONLY IF HSUPA2MSTTIEnabled IS ENABLED

WCEL_CM_0094 WCEL Create/Modify If the value of HSPAQoSEn-abled is 1 (QoS prioritization for HSPA NRT connections) or 2 (HSPA streaming is in use), HSDPAEnabled must be Enabled

HSPA QOS FOR NRT, HSPA STREAMING, CS VOICE OR HSPA STREAMING CS VOICE CAN BE USED ONLY WHEN HSDPA IS ENABLED

WCEL_CM_0095 WCEL Create/Modify If the value of HSPAQoSEn-abled is 1 (QoS prioritization for HSPA NRT connections) or 2 (HSPA streaming is in use), HSDPADynamicResourceAl-location must be Enabled

HSPA QOS FOR NRT, HSPA STREAMING, CS VOICE OR HSPA STREAMING CS VOICE CAN BE USED IF HSDPA DYN RES ALLOC USED

WCEL_CM_0096 WCEL Create/Modify NB/RSxxx BTS does not support the Streaming QoS for HSPA feature.

NB/RSXXX BTS DOES NOT SUPPORT STREAMING QOS FOR HSPA FEATURE

WCEL_CM_0098 WCEL Create/Modify If NBAPCommMode (NBAP Communication Mode) mis-matches with NEtype (Ne-type), WCEL Creation and modification are not allowed.

MISMATCH BETWEEN NBAP COMMUNICATION MODE AND NE-TYPE OF NODEB


Object type

Operation type



DN0934038 81




WCEL_CM_0099 WCEL Create/Modify WCEL and the Intra-Fre-quency neighboring WCEL must have different scrambling codes (PriScrCode) and the same frequency (uarfcn)

SOURCE AND TARGET WCELS MUST HAVE DIF-FERENT DL_PRI_SCR_CODE IN ADJS (INTRA-FREQ ADJ) SOURCE AND TARGET WCELS MUST HAVE SAME FREQS IN ADJS (INTRA-FREQ ADJ)

WCEL_CM_0100 WCEL Create/Modify WCEL and the additional intra-frequency adjacency WCEL must have different scrambling codes (PriScrCode) and the same frequency (uarfcn)

SOURCE AND TARGET CELLS MUST HAVE DIFFER-ENT PRIMARY SCRAM-BLING CODE IN ADJD SOURCE AND TARGET CELLS MUST HAVE SAME FREQUENCY IN ADJD

WCEL_CM_0101 WCEL Create/Modify WCEL and the Inter-frequency neighboring WCEL must have different frequencies

SOURCE AND TARGET WCELS MUST HAVE DIF-FERENT FREQS IN ADJI (INTER-FREQ ADJ)

WCEL_CM_0102 WCEL Create/Modify WCEL and the incoming intra-frequency adjacency (ADJS) must have the same scram-bling code (PriScrCode).

PRIMARY SCRAMBLING CODE MUST BE SAME FOR THE WCEL AND THE INCOMING ADJACENCY (ADJS)

WCEL_CM_0103 WCEL Create/Modify The primary scrambling code of an intra-frequency neighbor cell must be unique within the basic and additional intra-fre-quency neighbor cells.

PRIMARY SCRAMBLING CODE OF AN INTRA-FRE-QUENCY NEIGHBOUR CELL MUST BE UNIQUE WITHIN ADJS. PRIMARY SCRAMBLING CODE MUST BE UNIQUE WITHIN ADJD OF THE SAME SOURCE CELL

WCEL_CM_0104 WCEL Create/Modify The primary scrambling code of an additional intra-frequency neighbor cell must be unique within the basic and additional intra-frequency neighbor cells.

PRIMARY SCRAMBLING CODE OF AN ADJS AND AN ADJD OF THE SAME SOURCE WCEL MUST BE DIFFER-ENT PRIMARY SCRAMBLING CODE MUST BE UNIQUE WITHIN ADJD OF THE SAME SOURCE CELL


Object type

Operation type



82 DN0934038




WCEL_CM_0105 WCEL Create/Modify The primary scrambling code and the UTRA RF Channel Number combination of an inter-frequency neighbor cell must be unique within inter-fre-quency neighbor cells.

PRI SCRC AND UARFCN COMBINATION OF AN INTER-FREQ NEIGHBOUR CELL MUST BE UNIQUE WITHIN ADJI

WCEL_CM_0106 WCEL Create/Modify If WCEL-HSPA72UsersPerCell is set to Enabled, WCEL-HSUPAEN-ABLED must be Enabled

WCEL-HSPA72USERSPERCELL CAN BE ENABLED ONLY WHEN PARAMETER WCEL-HSUPAENABLED IS ENABLED.

WCEL_CM_0107 WCEL Create/Modify If WCEL-HSDPAMAXBITRA-TEUL is set to Enabled, RNC-HSDPA16KBPSRETURNCHANNEL must be Enabled.

VALUE OF WCEL-HSDPA-MAXBITRATEUL CAN BE 16KBPS ONLY WHEN RNC-HSDPA16KBPSRETURNCHANNEL IS ENABLED.

WCEL_CM_0108 WCEL Create/Modify WCEL-URAId must be unique within WCEL-URAIdList.

WCEL-URAID MUST BE UNIQUE WITHIN WCEL-URAIIDLIST.

WCEL_CM_0109 WCEL Create/Modify The value of WCEL-NbrofSC-CPCHs cannot be 1 if WCEL-PCH24kbpsEnable is Enabled.

WCEL-NBROFSCCPCHS CAN NOT BE ONE IF WCEL-PCH24KBPSENABLE IS ENABLED.

WCEL_CM_0110 WCEL Create/Modify The value of WCEL-AMRUnderTxNC must be lower than the value of WCEL-AMROverTxNC.

WCEL-AMRUNDERTXNC MUST BE SMALLER THAN WCEL-AMROVERTXNC.

WCEL_CM_0111 WCEL Create/Modify The number of MIMO 28Mbps support enabled wcels must not exceed the license capacity

THE NUMBER OF MIMO 28MBPS SUPPORT ENABLED WCELS EXCEED THE LICENSED CAPACITY

WCEL_CM_0112 WCEL Create/Modify WCEL-MIMOEnabled can be enabled only when RNC-HSDPA14MbpsPerUser is enabled.

WCEL-MIMOENABLED CAN BE ENABLED ONLY WHEN WBTS-HSDPA14MBPSPERUSER IS ENABLED

WCEL_CM_0113 WCEL Create/Modify WCEL-MIMOEnabled can be enabled only when RNC-FRL-CEnabled is enabled.

WCEL-MIMOENABLED CAN BE ENABLED ONLY WHEN RNC-FRLCENABLED IS ENABLED


Object type

Operation type



DN0934038 83




WCEL_CM_0114 WCEL Create/Modify The number of LTECellRese-lection enabled WCELs exceeds the license Cell Rese-lection to LTE capacity limit

THE NUMBER OF LTECELL-RESELECTION ENABLED WCELS EXCEEDS THE LICENSE CELL RESELEC-TION TO LTE CAPACITY LIMIT

WCEL_CM_0115 WCEL Create/Modify AbsPrioCellReselec and AdjLAbsPrioCellReselec always have unique values.

AbsPrioCellReselec and AdjLAbsPrioCellReselec always have unique values

WCEL_CM_0116 WCEL Create/Modify The number of Incom-ingLTEISHO enabled WCELs exceeds the license ISHO from LTE capacity limit

THE NUMBER OF INCOM-INGLTEISHO ENABLED WCELS EXCEEDS THE LICENSE ISHO FROM LTE CAPACITY LIMIT

WCEL_CM_0117 WCEL Create/Modify WCEL-DCellHSDPAEnabled can be enabled only when RNC-FRLCEnabled is enabled

WCEL-DCELLHSDPAEN-ABLED CAN BE ENABLED ONLY WHEN RNC-FRLCEN-ABLED IS ENABLED

WCEL_CM_0118 WCEL Create/Modify WCEL-DCellHSDPAEnabled can be enabled only when WBTS-HSDPA14MbpsPerUser is enabled

WCEL-DCELLHSDPAEN-ABLED CAN BE ENABLED ONLY WHEN WBTS- HSDPA14MBPSPERUSER IS ENABLED

WCEL_CM_0119 WCEL Create/Modify WCEL-DCellHSDPAEnabled can be enabled only when WCEL-MIMOEnabled is disabled in all cells under the WBTS

WCEL-DCELLHSDPAEN-ABLED CAN BE ENABLED ONLY WHEN WCEL-MIMOE-NABLED IS DISABLED IN ALL CELLS UNDER WBTS

WCEL_CM_0120 WCEL Create/Modify WCEL-DCellHSDPAEnabled can be enabled only when WCEL-HSUPAEnabled is enabled

WCEL-DCELLHSDPAEN-ABLED CAN BE ENABLED ONLY WHEN WCEL-HSU-PAENABLED IS ENABLED

WCEL_CM_0121 WCEL Create/Modify The number of DC HSDPA enabled cells must not exceed the license capacity

THE NUMBER OF DC HSDPA ENABLED CELLS MUST NOT EXCEED THE LICENSE CAPACITY

WCEL_CM_0122 WCEL Create/Modify WCEL- HSPAQoSEnabled can be set to cs_voice_c only when RNC-FRLCEnabled is set to Enabled

WCEL-HSPAQOSENABLED CAN BE SET TO CS_VOICE_C ONLY WHEN RNC-FRLCENABLED IS SET TO ENABLED


Object type

Operation type



84 DN0934038




WCEL_CM_0123 WCEL Create/Modify Cells forming DC HSDPA pairs should have the same WCEL-HSPAQoSEnabled parameter value

CELLS FORMING DC HSDPA PAIRS SHOULD HAVE SAME VALUE OF WCEL-HSPAQOSENABLED PARAMETER

WCEL_CM_0124 WCEL Create/Modify If WCEL-DCellHSDPAEnabled is set to 1, WCEL-HSPDSCH-Codeset must be set to HSDPA 15 Codes

IF WCEL-DCELLHSDPAEN-ABLED IS SET TO 1, WCEL-HSPDSCHCODESET MUST BE SET TO HSDPA 15 CODES

WCEL_CM_0125 WCEL Create/Modify The license state of DC HSDPA must be ON for cell unlocking when WCEL-DCellHSDPAEnabled is enabled

LICENSE STATE OF DC HSDPA MUST BE ON FOR CELL UNLOCKING WHEN WCEL-DCELLHSDPAEN-ABLED IS ENABLED

WCEL_CM_0126 WCEL Create/Modify WCEL-HSPA128UsersPerCell can only be enabled in the WCEL if WCEL-HSUPAEN-ABLED is enabled

PARAMETER WCEL-HSPA128USERSPERCELL CAN ONLY BE ENABLED IN WCEL IF WCEL-HSUPAEN-ABLED IS ENABLED

WCEL_CM_0127 WCEL Create/Modify WCEL-HSPA128UsersPerCell can only be enabled in the WCEL if WCEL-HSPA72USersPerCell is enabled

PARAMETER WCEL-HSPA128USERSPERCELL CAN ONLY BE ENABLED IN WCEL IF WCEL-HSPA72USERSPERCELL IS ENABLED

WCEL_CM_0128 WCEL Create/Modify WCEL-NumberED-CHReservedSHOBranchAddi-tions must be lower than the value of parameter WBTS-MaxNumberEDCHLCG

WCEL-NUMBERED-CHRESERVEDSHO-BRANCHADDITIONS MUST BE LOWER THAN VALUE OF PARAMETER WBTS-MAX-NUMBEREDCHLCG

WCEL_CM_0129 WCEL Create/Modify WCEL-NumberED-CHReservedSHOBranchAddi-tions must be lower than the value of parameter WCEL-MaxNumberEDCHCell

WCEL-NUMBERED-CHRESERVEDSHO-BRANCHADDITIONS MUST BE LOWER THAN VALUE OF PARAMETER WCEL-MAX-NUMBEREDCHCELL


Object type

Operation type



DN0934038 85




WCEL_CM_0130 WCEL Create/Modify HSFACHEnabled can be set to enabled only when the hardware of CDSP-DH with upgrade mode is present

HSFACHENABLED CAN BE SET TO ENABLED ONLY WHEN THE HARDWARE OF CDSP-DH WITH UPGRADE MODE IS PRESENTPRE-SENT

WCEL_CM_0131 WCEL Create/Modify WCEL-HSFACHEnabled can be enabled only when WCEL-HSDPAEnabled is enabled.

WCEL-HSFACHENABLED CAN BE ENABLED ONLY WHEN WCEL-HSDPAEN-ABLED IS ENABLED

WCEL_CM_0132 WCEL Create/Modify HSFACHEnabled can be enabled only when WCEL-PowerSaveHSPAType has the value no_hspa_cnf_c or def_c or hspa_5_c

HSFACHENABLED CAN BE ENABLED ONLY WHEN WCEL-POWERSAVEHSPA-TYPE HAS NO_HSPA_CNF_C OR DEF_C OR HSPA_5_C

WCEL_CM_0133 WCEL Create/Modify PIC-activated cells in PIC Pool exceed maximum limit

TOO MANY PIC ENABLED CELLS IN PIC POOL

WCEL_CM_0134 WCEL Create/Modify WCEL-AdminPICState can be automatic or active only when WCEL-HSUPA2MSTTIEnabled is enabled.

WCEL-ADMINPICSTATE CAN BE AUTOMATIC OR ACTIVE ONLY WHEN WCEL-HSUPA2MSTTIENABLED IS ENABLED

WCEL_CM_0135 WCEL Create/Modify The PrxMaxOrigTargetBTS value must be greater than or equal to the value of PrxMax-TargetBTS.

PRXMAXORIGTARGETBTS VALUE MUST BE GREATER THAN OR EQUAL TO VALUE OF PRXMAXTARGETBTS

WCEL_CM_0136 WCEL Create/Modify If WCEL-MIMOWith64QAMUsage is enabled, then WCEL-MIMOE-nabled must be enabled.

IF WCEL-MIMOWITH64QAMUSAGE IS ENABLED, THEN WCEL-MIMOENABLED MUST BE ENABLED

WCEL_CM_0137 WCEL Create/Modify If WCEL-MIMOWith64QAMUsage is enabled, then WCEL-HSDPA64QAMallowed must be enabled

IF WCEL-MIMOWITH64QAMUSAGE IS ENABLED, THEN WCEL-HSDPA64QAMALLOWED MUST BE ENABLED

WCEL_CM_0138 WCEL Create/Modify WCEL-HSUPA16QAMAllowed can be set as enabled only if WCEL-MaxTotalUplinkSymbolRate is 5760 kbps

WCEL-HSUPA16QAMALLOWED CAN BE SET AS ENABLED ONLY IF WCEL-MAXTOTAL-UPLINKSYMBOLRATE IS 5760 KBPS


Object type

Operation type



86 DN0934038




WCEL_CM_0139 WCEL Create/Modify HSPAQoSEnabled can be set to cs_voice_c or str_cs_c only when AMRWithHSDSCH is Enabled

HSPAQOSENABLED CAN BE SET TO CS_VOICE_C OR STR_CS_C ONLY WHEN AMRWITHHSDSCH IS ENABLED

WCEL_CM_0140 WCEL Create/Modify HSPAQoSEnabled can be set to cs_voice_c or str_cs_c only when AMRWithEDCH is Enabled

HSPAQOSENABLED CAN BE SET TO CS_VOICE_C OR STR_CS_C ONLY WHEN AMRWITHEDCH IS SET TO ENABLED

WCEL_CM_0141 WCEL Create/Modify WCEL-DCellHSDPAEnabled can be enabled only when RNC-HSDPAMobility is enabled.

WCEL-DCELLHSDPAEN-ABLED CAN BE ENABLED ONLY WHEN RNC-HSDPA-MOBILITY IS ENABLED

WCEL_CM_0142 WCEL Create/Modify MaxBitRateDLPSNRT should be higher than or equal to Ini-tialBitRateDL

MAXBITRATEDLPSNRT SHOULD BE BIGGER THAN OR EQUAL TO INITIALBI-TRATEDL

WCEL_CM_0143 WCEL Create/Modify InitialBitRateDL should be higher than or equal to MinAl-lowedBitRateDL

INITIALBITRATEDL SHOULD BE BIGGER THAN OR EQUAL TO MINALLOWEDBI-TRATEDL

WCEL_CM_0144 WCEL Create/Modify PtxTargetTotMin cannot take values that are lower than the value of PtxTarget

PTXTARGETTOTMIN CANNOT TAKE VALUES WHICH ARE LESS THAN THE VALUE OF PTXTARGET

WCEL_CM_0145 WCEL Create/Modify PtxTargetTotMax cannot take values that are greater than the value of PtxCellMax

PTXTARGETTOTMAX CANNOT TAKE VALUES WHICH ARE GREATER THAN THE VALUE OF PTX-CELLMAX

WCEL_CM_0146 WCEL Create/Modify PtxTargetTotMin cannot take values that are greater than the value of PtxTargetTotMax

PTXTARGETTOTMIN CANNOT TAKE VALUES WHICH ARE GREATER THAN THE VALUE OF PTX-TARGETTOTMAX

WCEL_CM_0147 WCEL Create/Modify PtxTarget cannot take values that are greater than the value of PtxTargetTotMax.

PTXTARGET CANNOT TAKE VALUES WHICH ARE GREATER THAN THE VALUE OF PTXTARGETTOTMAX


Object type

Operation type



DN0934038 87




WCEL_CM_0148 WCEL Create/Modify PrxTargetMax cannot take values that are lower than the value of PrxTarget

PRXTARGETMAX CANNOT TAKE VALUES WHICH ARE SMALLER THAN THE VALUE OF PRXTARGET

WCEL_CM_0149 WCEL Create/Modify WCEL-PTXCELLMAX must be greater than or equal to WCEL-PTXMAXHSDPA

WCEL-PTXCELLMAX MUST BE GREATER THAN OR EQUAL TO WCEL-PTX-MAXHSDPA

WCEL_CM_0150 WCEL Create/Modify If the parameter CPCEnabled of WCEL is enabled, the parameter FDPCHEnabled of WCEL must be enabled. If the parameter FDPCHEnabled of WCEL is disabled, the param-eter CPCEnabled of WCEL must be disabled

IF CPCENABLED ENABLED,FDPCHENABLED MUST BE ENABLED;IF FDP-CHENABLED DIS-ABLED,CPCENABLED MUST BE DISABLED

WCEL_CM_0151 WCEL Create/Modify WCEL-HSDPA64QAMallowed can be enabled only when the hardware of CDSP-DH is present in upgrade mode

WCEL-HSDPA64QAMALLOWED CAN BE ENABLED ONLY WHEN THE HARDWARE OF CDSP-DH IS PRESENT IN UPGRADE MODE

WCEL_CM_0152 WCEL Create/Modify WCEL-HSDPAEnabled must be set as enabled if WCEL-HSDPA64QAMallowed is enabled.

WCEL-HSDPAENABLED MUST BE SET AS ENABLED IF WCEL-HSDPA64QAMALLOWED IS ENABLED.

WCEL_CM_0153 WCEL Create/Modify WCEL-MIMOEnabled can be enabled only when WCEL-HSUPA2MSTTIEnabled is enabled.

WCEL-MIMOENABLED CAN BE ENABLED ONLY WHEN WCEL-HSUPA2MSTTIEnabled IS ENABLED

WCEL_CM_0154 WCEL Create/Modify MIMOEnabled cannot be set as enabled with DCellHSD-PAEnbaled if HSUPAEnabled set as disabled.

MIMOENABLED CANNOT BE SET AS ENABLED WITH DCELLHSDPAENBALED IF HSUPAENABLED SET AS DISABLED

WCEL_CM_0155 WCEL Create/Modify WCEL-DCellHSDPAFmcsId cannot have not-defined value if WCEL-DCellHSDPAEnabled is set to enabled.

WCEL-DCELLHSDPAFMC-SID CAN NOT HAVE NOT DEFINED VALUE IF WCEL-DCELLHSDPAENABLED IS SET TO ENABLED


Object type

Operation type



88 DN0934038




WCEL_CM_0156 WCEL Create/Modify If WCEL-DCellHSDPAEnabled is set to enabled then WCEL-SectorID should not be set as default.

IF WCEL-DCELLHSDPAEN-ABLED IS SET TO ENABLED THEN WCEL-SECTORID SHOULD NOT BE SET AS DEFAULT.

WCEL_CM_0157 WCEL Create/Modify If DC-HSDPA is enabled in any cell of the sector, MIMO must not be enabled in any other cell than the DC-HSDPA cell.

IF DC-HSDPA IS ENB IN ANY CELL OF THE SEC,MIMO MUST NOT BE ENB IN ANY OTHER CELL THAN DC-HSDPA CELL

WCEL_CM_0158 WCEL Create/Modify During WCEL modifica-tion,SectorId cannot be modified if the DCellHSD-PAEnabled parameter is already enabled.

DURING WCEL MODIFICA-TION,SECTORID CANNOT BE MODIFIED IF DCELLHSD-PAENABLED PARAMETER IS ALREADY ENABLED

WCEL_CM_0159 WCEL Create/Modify NB/RSxxx BTS does not support Streaming QoS and the CS Voice over HSPA for HSPA feature

NB/RSXXX BTS DOES NOT SUPPORT STREAMING QOS AND CS VOICE OVER HSPA FOR HSPA FEATURE

WCEL_CM_0160 WCEL Create/Modify MaxBitRateULPSNRT should be greater than or equal to Ini-tialBitRateUL

MAXBITRATEULPSNRT SHOULD BE BIGGER THAN OR EQUAL TO INITIALBI-TRATEUL

WCEL_CM_0161 WCEL Create/Modify If WCEL-DCellAndMIMOUs-age is enabled with the value 1 or 2, then WCEL-FDPCHEn-abled must be enabled.

IF WCEL-DCELLANDMI-MOUSAGE IS ENABLED WITH VALUE 1 OR 2, THEN WCEL-FDPCHENABLED MUST BE ENABLED.

WCEL_CM_0162 WCEL Create/Modify If WCEL-DCellAndMIMOUs-age is enabled with the value 1 or 2, then WCEL-DCellHSD-PAEnabled must be enabled.

IF WCEL-DCELLANDMI-MOUSAGE IS ENABLED WITH VALUE 1 OR 2, THEN WCEL-DCELLHSDPAEN-ABLED MUST BE ENABLED.

WCEL_CM_0163 WCEL Create/Modify If WCEL-DCellAndMIMOUs-age is enabled with the value 1 or 2, then WCEL-MIMOEn-abled must be enabled.

IF WCEL-DCELLANDMI-MOUSAGE IS ENABLED WITH VALUE 1 OR 2, THEN WCEL-MIMOENABLED MUST BE ENABLED

WCEL_CM_0164 WCEL Create/Modify If WCEL-DCellAndMIMOUs-age is enabled with the value 2, then WCEL-HSDPA64QAMallowed must be enabled.

IF WCEL-DCELLANDMI-MOUSAGE IS ENABLED WITH VALUE 2, THEN WCEL-HSDPA64QAMALLOWED MUST BE ENABLED.


Object type

Operation type



DN0934038 89




WCEL_CM_0165 WCEL Create/Modify If WCEL-DCellAndMIMOUs-age is enabled with the value 2, then WCEL-MIMOWith64QAMUsage must be enabled.

IF WCEL-DCELLANDMI-MOUSAGE IS ENABLED WITH VALUE 2, THEN WCEL-MIMOWITH64QAMUSAGE MUST BE ENABLED.

WCEL_CM_0166 WCEL Create/Modify The count of CCH Setup-enabled WCELs exceeds the license CCHSetup capacity limit.

THE COUNT OF CCH SETUP-ENABLED WCELS EXCEEDS THE LICENSE CCHSETUP CAPACITY LIMIT

WCEL_CM_0167 WCEL Create/Modify The number of DC HSDPA-enabled cells must not exceed the license capacity.

THE NUMBER OF DC HSDPA-ENABLED CELLS MUST NOT EXCEED THE LICENSE CAPACITY

WCEL_CM_0168 WCEL Create/Modify The number of MIMO 28Mbps support-enabled WCELs must not exceed the licensed capac-ity.

THE NUMBER OF MIMO 28MBPS SUPPORT-ENABLED WCELS EXCEEDED THE LICENSED CAPACITY

WCEL_CM_0169 WCEL Create/Modify The number of LTECellRese-lection enabled WCELs exceeds the license Cell Rese-lection to LTE capacity limit.

THE NUMBER OF LTECELL-RESELECTION ENABLED WCELS EXCEEDS THE LICENSE CELL RESELEC-TION TO LTE CAPACITY LIMIT

WCEL_CM_0170 WCEL Create/Modify The number of Incom-ingLTEISHO enabled WCELs exceeds the license ISHO from LTE capacity limit.

THE NUMBER OF INCOM-INGLTEISHO ENABLED WCELS EXCEEDS THE LICENSE ISHO FROM LTE CAPACITY LIMIT

WCEL_CM_0171 WCEL Create/Modify WCEL-HSFACHEnabled can be enabled only when RNFC-HSDPADynamicResourceAl-location is enabled.

WCEL-HSFACHENABLED CAN BE ENABLED ONLY WHEN RNFC-HSDPADY-NAMICRESOURCEALLOCA-TION IS ENABLED

WCEL_CM_0172 WCEL Create/Modify WCEL-HSFACHEnabled can be enabled only when RNFC-FRLCEnabled is enabled.

WCEL-HSFACHENABLED CAN BE ENABLED ONLY WHEN RNFC-FRLCEN-ABLED IS ENABLED.


Object type

Operation type



90 DN0934038




WCEL_CM_0173 WCEL Create/Modify MOCN WCEL can be created or modified only when MOC-Nenabled is enabled. MOC-Nenabled can be disabled only when no MOCN WCEL exists.

CONFIGURATING MOCN WCEL ONLY IF MOCNEN-ABLED IS ENABLED; DIS-ABLING MOCNENABLED ONLY IF NO MOCN WCEL EXISTS

WCEL_CM_0174 WCEL Create/Modify HSDPA64QAMallowed can be enabled only when FRLCEn-abled is enabled; FRLCEn-abled can be disabled only if all HSDPA64QAMallowed is dis-abled.

HSDPA64QAMALLOWED CAN BE ENABLED ONLY WHEN FRLCENABLED IS ENABLED

WCEL_CM_0175 WCEL Create/Modify WBTS-ICREnabled cannot be set to Enabled if DCHSD-PAEnabled is Enabled for any WCEL under this cell

WBTS-ICRENABLED CAN BE ENABLED ONLY WHEN WCEL-DCHSDPA IS DISABLED FOR ALL WCELS

WCEL_CM_0176 WCEL Create/Modify WBTS-ICREnabled cannot be set to Enabled if IMSIBasedHO is not set to “allowed(1)”, that is, “1” for any WCEL under this cell

IMSIBASEDGSMHO MUST BE ENBALED FOR ALL THE WCELS UNDER BTS HAVING WBTS-ICREN-ABLED AS ENABLED

WCEL_M_0001 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, no outgoing ADJS cells HSDPA-HopsIdentifier have the value hops_id_t_not_def

HSDPA HOPS MUST BE DEFINED FOR OUTGOING ADJS OF THE WCEL

WCEL_M_0002 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, and AMRWithHSDSCH is Enabled, the "no outgoing ADJS cells" RTWithHSDPAHopsIdentifier value is hops_id_t_not_def_c

HSDPA HOPS FOR AMR MULTI-SERVICE MUST BE DEFINED FOR THE OUTGOING ADJS OF THE WCEL

WCEL_M_0003 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, the "no outgoing ADJD cells" HSDPA-HopsIdentifier value is hops_id_t_not_def

HSDPA HOPS ID MUST BE DEFINED FOR OUTGOING ADJD OF HSDPA ENABLED CELL

WCEL_M_0004 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, and AMRWithHSDSCH is Enabled, the "no outgoing ADJD cells" RTWithHSDPAHopsIdentifier value is hops_id_t_not_def_c

RT HSDPA HOPS ID MUST BE DEFINED FOR OUTGOING ADJD OF HSDPA ENABLED CELL


Object type

Operation type



DN0934038 91




WCEL_M_0005 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, and ADJI is defined, the hsdpa_fmci_id value fmci_id_t_not_def is not allowed

HSDPA FMCI MUST BE DEFINED IF HSDPA ENABLED AND ADJI(S) CREATED UNDER THE WCEL

WCEL_M_0006 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, AMR-WithHSDSCH is Enabled and ADJI is defined, the rt_hsdpa_fmci_id value fmci_id_t_not_def_c is not allowed


WCEL_M_0007 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, and ADJG is defined, the hsdpa_fmcg_id value fmcg_id_t_not_def is not allowed

HSDPA FMCG MUST BE DEFINED IF HSDPA ENABLED AND ADJG(S) CREATED UNDER THE WCEL

WCEL_M_0008 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, AMR-WithHSDSCH is Enabled, and ADJG is defined, the rt_hsdpa_fmcg_id value fmcg_id_t_not_def_c is not allowed


WCEL_M_0009 WCEL Modify The following HSDPA feature related parameters request object locking when modified: HSDPAEnabled, PtxMaxHS-DPA, HSPDSCHCodeSet, MaxNbrOfHSSCCHCodes


WCEL_M_0010 WCEL Modify If AMRDirReCell (Usage of Directed Retry of AMR call Inter-system Handover) is Enabled, and the target cell of the directed retry of AMR call is the cell whose ADJGid (Inter-system adjacency identifier) has the value 0 , then AdjgSIB (Include in System Informa-tion) must be default (yes)


WCEL_M_0011 WCEL Modify CId (Cell identifier) is unmodifi-able

CELL IDENTIFIER MAY NOT BE CHANGED


Object type

Operation type



92 DN0934038




WCEL_M_0012 WCEL Modify UARFCN (UTRA Absolute Radio Frequency Channel Number) is unmodifiable

UARFCN MAY NOT BE CHANGED

WCEL_M_0013 WCEL Modify WCEL - WCELGlobalCNid -WCELPLMNid (PLMN identity) is unmodifiable

THE IDENTIFIER OF PLMN NOT MODIFIABLE

WCEL_M_0014 WCEL Modify WCEL - WCELGlobalCNid -WCELCSCNId (CS Core Network Identity) is unmodifi-able

CS CN IS UNMODIFIABLE

WCEL_M_0015 WCEL Modify WCEL - WCELGlobalCNid -WCELPSCNId (PS Core Network Identity) is unmodifi-able

PS CN IS UNMODIFIABLE

WCEL_M_0016 WCEL Modify The folllowing parameters request WCEL object locking before a modification: NbrOf-SCCPCHs (Number of SCCPCHs), CellRange (if Nokia BTS with 3GPP inter-face is involved), PtxCellMax (Cell maximum transmission power), EbNoSetIdentifier, AICHTraTime, PI_amount, PRACHScramblingCode, RACHCapacity, PowerOff-setSCCPCHTFCI



Object type

Operation type



DN0934038 93




WCEL_M_0017 WCEL Modify If NBAPCommMode is NB/RSXXX, the following parameters request WCEL object locking before a modifi-cation:

Cell Reconfig Parameters:

• PtxPrimarySCH • PtxSecSCH • PtxPrimaryCPICH • PtxPrimaryCCPCH

PRACH parameters:

• AllowedPreambleSigna-tures

• AllowedRACHSubChan-nels

• PtxAICH

SCCPCH parameters:

• ToAWS_CCH • ToAWE_CCH • PtxSCCPCH1,

PtxSCCPCH2, PtxSCCPCH3

• PtxPICH


WCEL_M_0018 WCEL Modify If HSUPA2MSTTIEnabled is modified, RAKTOR must ensure that the WCEL opera-tional state is BL-U (blocked by user)


WCEL_M_0019 WCEL Modify If MaxTotalUplinkSymbolRate is modified, RAKTOR must ensure that the WCEL opera-tional state is BL-U (blocked by user)


WCEL_M_0020 WCEL Modify WCEL and the Intra-frequency adjacency within it must have different scrambling codes (PriScrCode)

ADJS (INTRA-FREQ ADJ) AND SOURCE WCEL MUST HAVE DIFFERENT DL_PRI_SCR_CODE

WCEL_M_0021 WCEL Modify WCEL and the additional Intra-frequency adjacency within it must have different scrambling codes (PriScrCode)

ADJD AND SOURCE CELL MUST HAVE DIFFERENT PRIMARY SCRAMBLING CODE


Object type

Operation type



94 DN0934038




WCEL_M_0022 WCEL Modify The count of CCH Setup enabled WCELs must not exceed the license CCHSetup capacity limit.

THE COUNT OF CCH SETUP ENABLED WCEL'S EXCEEDS THE LICENSE CCHSETUP CAPACITY LIMIT.

WCEL_M_0023 WCEL Modify WCEL-PWSMCellGroup, WCEL-PWSMShutdownOr-der, WCEL-PWSMShutdown-RemCell, and WCEL-PowersaveHSPAType cannot be modified if WBTS-PWSMI-nUse is ON.

PWSMCELLGROUP,PWSM-SHUTDOWNORDER,PWSM-SHUTDOWNREMCELL,POWERSAVEHSPATYPE CAN NOT BE MODIFIED IF PWSMINUSE IS ON

WCEL_M_0024 WCEL Modify High-speed cell FACH is enabled in the RNC but disabled in the BTS

HIGH SPEED CELL FACH IS ENABLED IN RNC BUT DISABLED IN BTS

WCEL_M_0025 WCEL Modify AdminPICState set by operator is mismatching with PIC State received from Node-B

ADMINPICSTATE SET BY OPERATOR IS MISMATCH-ING WITH PIC STATE RECEIVED FROM NODE-B.

WCEL_M_0026 WCEL Modify The value of InitialBitRateUL should be higher than or equal to the value of MinAllowedBi-tRateUL.

INITIALBITRATEUL SHOULD BE BIGGER THAN OR EQUAL TO MINALLOWEDBI-TRATEUL

WCEL_M_0027 WCEL Modify WCEL-PLMNid must be the same as IUCS/IUPS-PLMNid.


WCEL_M_0028 WCEL Modify The number of EVAM enabled WCELs must not exceed the licensed capacity.

THE NUMBER OF EVAM ENABLED WCELS EXCEEDED THE LICENSED CAPACITY.

WCEL_U_0001 WCEL Unlock If NBAPCommMode (NBAP Communication Mode) mis-matches with NEtype (Ne-type), WCEL unlocking is not allowed.

MISMATCH BETWEEN NBAP COMMUNICATION MODE AND NE-TYPE OF NODEB

WCEL_U_0002 WCEL Unlock If HSDPAEnabled (HSDPA Enabled) is Enabled, the optional license HSDPA state should be ON

BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON


Object type

Operation type



DN0934038 95




WCEL_U_0003 WCEL Unlock If HSDPADynamicRe-sourceAllocation is Enabled, the HSDPA and HSDPA Dynamic Resource Allocation license state should be ON

BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA DYNAMIC RESOURCE ALLOCATION LICENCE STATE CON-FIG/OFF, NOT ON

WCEL_U_0004 WCEL Unlock If the maximum code value in HSPDSCHCodeSet is higher than 10, the HSDPA 15 Codes license state should be ON

HSDPA 15 CODES LICENCE STATE CONFIG/OFF, NOT ON

WCEL_U_0005 WCEL Unlock If the maximum code value in HSPDSCHCodeSet is between 5 and 10, the optional license HSDPA 15 Codes or HSDPA 10 Codes state should be ON

HSDPA 10 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA 15 CODES LICENCE STATE CON-FIG/OFF, NOT ON

WCEL_U_0006 WCEL Unlock If HSUPAEnabled (HSUPA Enabled) is Enabled, the HSDPA (optional) and HSDPA Dynamic Resource Allocation (optional), and HSUPA X Users (optional, according to value of HSUPAXUsersEn-abled) license states should be ON

(HSUPA 3 USERS PER BTS LICENCE STATE NOT ON HSUPA 12 USERS PER BTS LICENCE STATE NOT ON HSUPA 24 USERS PER BTS LICENCE STATE NOT ON HSUPA 60 USERS PER BTS LICENCE STATE NOT ON ) HSDPA DYNAMIC RESOURCE ALLOCATION LICENCE STATE CON-FIG/OFF, NOT ON BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON

WCEL_U_0007 WCEL Unlock If HSUPAEnabled is Enabled, the AAL2UPUsage on the con-nected COCO should be of the HSUPA or HSPA type

INVALID USERPLANE WHEN HSUPA ENABLED


Object type

Operation type



96 DN0934038




WCEL_U_0008 WCEL Unlock If the value of HSPAQoSEn-abled is 1(QoS prioritization for HSPA NRT connections), HSDPA (optional) and HSDPA Dynamic Resource Allocation (optional) and QoS Aware HSPA Scheduling (optional) license states should be ON

BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA DYNAMIC RESOURCE ALLOCATION LICENCE STATE CON-FIG/OFF, NOT ON THE STATE OF LICENCE FEATURE QOS AWARE HSPA SCHEDULING IS NOT ON

WCEL_U_0009 WCEL Unlock If the value of HSPAQoSEn-abled is 2 (HSPA streaming is in use), HSDPA (optional) and HSDPA Dynamic Resource Allocation (optional), and QoS Aware HSPA Scheduling (optional), and HSPA with Streaming QoS Support (optional) license states should be ON

BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA DYNAMIC RESOURCE ALLOCATION LICENCE STATE CON-FIG/OFF, NOT ON THE STATE OF LICENCE FEATURE QOS AWARE HSPA SCHEDULING IS NOT ON THE STATE OF LICENCE FEATURE HSPA WITH STREAMING QOS SUPPORT IS NOT ON

WCEL_U_0010 WCEL Unlock If the value of MaxNbrOfHSS-CCHCodes is higher than 1, the HSDPA (optional), HSDPA Dynamic Resource Allocation (optional), and HSDPA Code Multiplexing (optional) and (HSDPA 15 Codes (optional) or HSDPA 10 Codes (optional) license states should be ON

BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA DYNAMIC RESOURCE ALLOCATION LICENCE STATE CON-FIG/OFF, NOT ON HSDPA CODE MULTIPLEXING LICENCE STATE CON-FIG/OFF, NOT ON HSDPA 10 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA 15 CODES LICENCE STATE CON-FIG/OFF, NOT ON


Object type

Operation type



DN0934038 97




WCEL_U_0011 WCEL Unlock If the value of CellRange is between 20Km and 35Km, the Extended cell 35km (optional) or Extended cell 60km (optional) or Extended cell 180km (optional) license state should be ON

NEEDED EXTENDED CELL RANGE LICENCE STATE CONFIG/OFF, NOT ON

WCEL_U_0012 WCEL Unlock If the value of CellRange is between 35Km and 60Km, the Extended cell 60km (optional) or Extended cell 180km (optional) license state should be ON


WCEL_U_0013 WCEL Unlock If the value of CellRange is greater than 60Km, the Extended cell 180km (optional) license state should be ON


WCEL_U_0014 WCEL Unlock If the value of HSDPA64UsersEnabled is Enabled, HSDPA (optional) and the HSDPA 64 Users per Cell (optional) license state should be ON

BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON

WCEL_U_0015 WCEL Unlock If the value of MaxTotalUplink-SymbolRate is 2 (3840 kbps, 2*SF2), at least one HSUPA X Users (optional) license state should be ON and the HSDPA 2.0 Mbps (optional) license state should be ON

THE LICENCE STATE OF BASIC HSUPA BTS ERROR HSUPA 2.0 MBPS LICENCE STATE NOT ON

WCEL_U_0016 WCEL Unlock If HSUPA is activated, it must be activated in all cells that use the same frequency (UARFCN) in the same BTS.


WCEL_U_0017 WCEL Unlock If HSUPA is deactivated, it must be deactivated in all cells that use the same frequency (UARFCN) in the same BTS.


WCEL_U_0018 WCEL Unlock If HSUPA2MSTTIEnabled is set to Enabled, the HSUPA 2ms TTI (optional) license state should be ON

LICENSE HSUPA 2MS TTI IS NOT ON


Object type

Operation type



98 DN0934038




WCEL_U_0019 WCEL Unlock If MaxTotalUplinkSymbolRate is set to (5760kbps, 2*SF2+2*SF4), the HSUPA 5.8Mbps (optional) license state should be ON

LICENSE HSUPA 5.8MBPS IS NOT ON

WCEL_U_0020 WCEL Unlock If WCEl-HSPA72UsersPerCell is set to Enabled, the license state of “HSPA 72 Users Per Cell” (optional) should be ON

LICENSE STATE OF HSPA 72 USERS PER CELL MUST BE ON FOR CELL UNLOCK-ING WHEN HSPA72USERSPERCELL IS ENABLED.

WCEL_U_0021 WCEL Unlock If PCH24kbpsEnabled is Enabled and NbrofSCCPCHs is greater than 1, then the 24kbps Paging Channel License state must be ON for the purpose of cell unlocking

24KBPS PAGING CHANNEL LICENSE STATE IS NOT ON.

WCEL_U_0022 WCEL Unlock WCEL-HSPA128USERSPERCELL can be enabled only when the HSPA 128 Users Per Cell license is On

WCEL-HSPA128USERSPERCELL CAN BE ENABLED ONLY WHEN THE HSPA 128 USERS PER CELL LICENSE IS ON

WCEL_U_0023 WCEL Unlock HSFACH cannot be activated because the HSFACH license state is CONFIG/OFF instead of ON

HSFACH CANNOT BE ACTI-VATED BECAUSE THE HSFACH LICENSE STATE IS CONFIG/OFF INSTEAD OF ON

WCEL_U_0024 WCEL Unlock EmergencyCallRedirect cannot be enabled because the state of the Emergency Call Redirect to GSM license is CONFIG/OFF, not ON.

EMERGENCY CALL REDIRECT TO GSM LICENCE STATE CON-FIG/OFF, NOT ON

WCEL_U_0025 WCEL Unlock HSDPAMobility cannot be acti-vated because the state of the HSDPA Serving Cell Change and Soft/Softer HO license is CONFIG/OFF, not ON.

HSDPA SERVING CELL CHANGE AND SOFT/SOFTER HO LICENCE STATE CONFIG/OFF, NOT ON

WCEL_U_0026 WCEL Unlock AMRWithHSDSCH cannot be activated because the state of the HSDPA with Simultaneous AMR Voice Call license is CONFIG/OFF, not ON.

HSDPA WITH SIMULTANE-OUS AMR VOICE CALL LICENCE STATE CON-FIG/OFF, NOT ON


Object type

Operation type



DN0934038 99




WCEL_U_0027 WCEL Unlock HSDPA16KBPSReturnChannel cannot be activated because the state of the 16 kbit/s Return Channel DCH Data Rate Support for HSDPA license is CONFIG/OFF, not ON.

16 KBIT/S RETURN CHANNEL DCH DATA RATE SUPPORT FOR HSDPA LICENCE STATE CON-FIG/OFF, NOT ON

WCEL_U_0028 WCEL Unlock HSDPA48UsersEnabled cannot be activated because the state of the HSDPA 48 Users per Cell license is CON-FIG/OFF, not ON.

HSDPA 48 USERS PER CELL LICENCE STATE CON-FIG/OFF, NOT ON

WCEL_U_0029 WCEL Unlock HSDPALayeringCom-monChEnabled cannot be acti-vated for the WCEL, because the HSDPA Layering for UEs in Common Channels license state is CONFIG/OFF, not ON.

HSDPA LAYERING FOR UES IN COMMON CHANNELS LICENCE STATE CON-FIG/OFF, NOT ON

WCEL_U_0030 WCEL Unlock The state of the HSUPA with simultaneous AMR voice call license is CONFIG/OFF, not ON. Therefore AMR-WithEDCH cannot be acti-vated.

HSUPA WITH SIMULTANE-OUS AMR VOICE CALL LICENCE STATE CON-FIG/OFF, NOT ON

WCEL_U_0031 WCEL Unlock IuFlex cannot be activated for either the IU-CS or IU-PS, because the Flexible Iu license state is CONFIG/OFF instead of ON

FLEXIBLE IU LICENCE STATE CONFIG/OFF, NOT ON

WCEL_U_0032 WCEL Unlock The HSPA Inter-RNC HHO license is not activated.

HSPA INTERRNC HHO LICENCE IS NOT ACTI-VATED

WCEL_U_0033 WCEL Unlock The IP Based IUPS license is not active.

IP BASED IUPS LICENSE NOT ACTIVE

WCEL_U_0034 WCEL Unlock The IP based IUCS license is not active.

IP BASED IUCS LICENSE NOT ACTIVE

WCEL_U_0035 WCEL Unlock HSDPA64QAMallowed cannot be activated, because the HSDPA64QAM license state is CONFIG/OFF instead of ON.

HSDPA64QAMALLOWED CANNOT BE ACTIVATED, BECAUSE THE HSDPA64QAM LICENSE STATE IS CONFIG/OFF INSTEAD OF ON.


Object type

Operation type



100 DN0934038




WCEL_U_0036 WCEL Unlock The state of license feature CS Voice Over HSPA is not ON

THE STATE OF LICENCE FEATURE CS VOICE OVER HSPA IS NOT ON

WCEL_U_0037 WCEL Unlock MOCN cannot be activated, because the MOCN license state is CONFIG/OFF instead of ON.

MOCN CANNOT BE ACTI-VATED, BECAUSE THE MOCN LICENSE STATE IS CONFIG/OFF INSTEAD OF ON.

WCEL_U_0038 WCEL Unlock The license state of MIMO 28Mbps must be ON for cell unlocking when WCEL-MIMOEnabled is enabled

LICENSE STATE OF MIMO 28MBPS MUST BE ON FOR CELL UNLOCKING WHEN WCEL-MIMOENABLED IS ENABLED

WCEL_U_0039 WCEL Unlock The license state of HSUPA16QAM must be on for cell unlocking when WCEL-HSUPA16QAMAllowed is enabled.

LICENSE STATE OF HSUPA16QAM MUST BE ON FOR CELL UNLOCKING WHEN WCEL-HSUPA16QAMALLOWED IS ENABLED

WCEL_U_0040 WCEL Unlock The license state of HSUPA16QAM must be on for cell unlocking when WCEL-HSUPA16QAMAllowed is enabled.

LICENSE STATE OF HSUPA16QAM MUST BE ON FOR CELL UNLOCKING WHEN WCEL-HSUPA16QAMALLOWED IS ENABLED

WCEL_U_0041 WCEL Unlock A parameter noticed to be invalid by an individual process. NOTICE: THIS IS NOT A DMX ERROR.

INVALID PARAMETER

WCEL_U_0042 WCEL Unlock Invalid license/feature state. INVALID LICENSE/FEA-TURE STATE


Object type

Operation type



DN0934038 101


WLCSE consistency checking rules

Id:0900d805808902dfConfidential

36 WLCSE consistency checking rulesThe following table lists the WLCSE consistency checking rules.


Object type

Operation type


WLCSE_C_0001 WLCSE Create A WSMLC object must be found in the RNC

WSMLC NOT FOUND

WLCSE_C_0002 WLCSE Create The maximum number of WLCSE objects in RNW database is 8000

MAXIMUM NUMBER OF WLCSES EXCEEDED

WLCSE_D_0001 WLCSE Delete If a parent WBTS has WBTS-BroadcastSIB15 as Enabled, a WLCSE cannot be deleted for a cell

WLCSE CAN NOT BE DELETED FOR A CELL IF ITS PARENT WBTS HAS WBTS-BROADCASTSIB15 AS ENABLED

Table 36 WLCSE consistency checking rules

102 DN0934038



WRAB consistency checking rules

37 WRAB consistency checking rulesThe following table lists the WRAB consistency checking rules.


Object type

Operation type


WRAB_D_0001 WRAB Delete A WRAB object cannot be deleted if any cell or cells have associations with it. In order to delete the WRAB, remove all cell associations. After that, the WRAB object can be deleted.

WRAB WITH EXISTING CELL ASSOCIATION(S) CANNOT BE DELETED

WRAB_D_0002 WRAB Delete WRAB still used by the VCEL WRAB STILL USED BY THE VCEL

WRAB_M_0001 WRAB Modify WRAB cannot be modified if there are some unlocked WCELs related

MODIFICATION OF WRAB IS REJECTED DUE TO ITS ASSOCIATION WITH AN UNLOCKED WCEL

Table 37 WRAB consistency checking rules

DN0934038 103


WSG consistency checking rules

Id:0900d805807e032dConfidential

38 WSG consistency checking rulesThe following table lists the WSG consistency checking rules.


Object type

Operation type


WSG_CM_0001 WSG Create/Modify A WSG object can be created and modified if the related WANE object is found in the database, or if WANE id is default

WANE NOT FOUND

Table 38 WSG consistency checking rules

104 DN0934038



WSMLC consistency checking rules

39 WSMLC consistency checking rulesThe following table lists the WSMLC consistency checking rules.


Object type

Operation type


WSMLC_CM_0001 WSMLC Create/Modify The LCSInterfaceOption parameter can be changed to iupc_c only if either the NW_AGPS_SUPPORT or the AGPS_SUPPORT option is enabled, and if the IUPC_INTERFACE option is enabled

WSMLC IU-PC INTERFACE NOT SUPPORTED

WSMLC_CM_0002 WSMLC Create/Modify NW_AGPS_SUPPORT can be enabled only if LCSInterfa-ceOption is iupc_c

PARAMETER INTERDE-PENDENCE ERROR

WSMLC_CM_0003 WSMLC Create/Modify The NetworkIndicatorFor-SAS/SignallingPointCodeOf-SAS parameters can be changed to a valid value only if either the NW_AGPS_SUPPORT or the AGPS_SUPPORT option is enabled, and if the sas_if_option parameter is set to iupc_c

IU PC INTERFACE FOR NETWORK ASSISTED GPS NOT CONFIGURED

WSMLC_CM_0005 WSMLC Create/Modify PreferredAGPSMethod can be changed to the UE base method only if UEBased-AGPS is enabled


WSMLC_CM_0006 WSMLC Create/Modify PreferredAGPSMethod can be changed to NW Based Method only if Network-BasedAGPS is enabled


WSMLC_CM_0007 WSMLC Create/Modify Parameter OperationalMode can select the SAS Centric mode only when LCSInterfa-ceOption has the value Iupc

SAS CENTRIC MODE CAN ONLY BE SELECTED IF LCSINTERFACEOPTION HAS VALUE IUPC

WSMLC_CM_0008 WSMLC Create/Modify Parameter OperationalMode cannot select the SAS Centric mode when LCS Support for Anchoring has the value Enabled

LCS SUPPORT FOR ANCHORING CAN BE ENABLED ONLY WHEN OPERATIONAL MODE IS RNC CENTRIC MODE

Table 39 WSMLC consistency checking rules

DN0934038 105




WSMLC_CM_0009 WSMLC Create/Modify The priority of Shape is unique under CIRTTEmer-gencyShapeList and CIRTTShapeList separately if the value is not 0 (disabled)

THE SHAPE PRIORITY MUST BE UNIQUE UNDER CIRTTSHAPE PRIORITY LIST

WSMLC_CM_0010 WSMLC Create/Modify At least one shape priority is valid (not 0) under CIRTTE-mergencyShapeList and CIRTTShapeList separately

THE CIRTT SHAPE PRIORITY LIST SHOULD NOT BE EMPTY

WSMLC_CM_0012 WSMLC Create/Modify NW Based A-GPS can only be enabled if the LCS Inter-face option is Iupc

WSMLC-NETWORKBASED-AGPS CAN BE ENABLED ONLY IF WSMLC-LCSIN-TERFACEOPTION IS SET TO IUPC

WSMLC_CM_0013 WSMLC Create/Modify WSMLC-UEBasedAGPS can be enabled only if WSMLC-LCSInterfaceOption is set to IUPC

WSMLC-UEBASEDAGPS CAN BE ENABLED ONLY IF WSMLC-LCSINTERFA-CEOPTION IS SET TO IUPC

WSMLC_CM_0014 WSMLC Create/Modify WSMLC-UEBasedAGPS can only be enabled when RNC-LCSfunctionality is enabled.

WSMLC-UEBASEDAGPS CAN BE ENABLED ONLY WHEN RNC-LCSFUNC-TIONALITY IS ENABLED

WSMLC_CM_0015 WSMLC Create/Modify A WLCSE to the same UC ID already exists.

WLCSE TO SAME UC ID ALREADY EXISTS

WSMLC_CM_0016 WSMLC Create/Modify WSMLC-PreferredAGPS-Method can be network based only when WSMLC-NetworkBasedAGPS is enabled

WSMLC-PREFERRED-AGPSMETHOD CAN BE NETWORK BASED ONLY WHEN WSMLC-NETWORK-BASEDAGPS IS ENABLED

WSMLC_CM_0017 WSMLC Create/Modify WSMLC-preferred AGPS method can be UE based only when WSMLC-UE based AGPS is enabled.

WSMLC-PREFERRED AGPS METHOD CAN BE UE BASED ONLY WHEN WSMLC-UE BASED AGPS IS ENABLED

WSMLC_CM_0018 WSMLC Create/Modify The selected shape priorities in the list (CIRTTShapelist, CIRTTEmergencyShapelist) are not descending from the highest priority without gaps.

DEFINED CIRTT SHAPE PRIORITIES ARE NOT DESCENDING FROM THE HIGHEST PRIORITY WITHOUT GAPS

WSMLC_CM_0019 WSMLC Create/Modify WLCSECid cannot be modified if the identification of the Local RNC is RNC Identi-fier

WLCSECID CANNOT BE MODIFIED IF THE IDENTIFI-CATION OF THE LOCAL RNC IS RNC IDENTIFIER


Object type

Operation type


Table 39 WSMLC consistency checking rules (Cont.)

106 DN0934038




WSMLC_D_0001 WSMLC Delete WBTS-BroadcastSIB15 cannot be enabled when WSMLC-LCSInterfaceOption is not IUPC.

WBTS-BROADCASTSIB15 CAN NOT BE ENABLED WHEN WSMLC-LCSINTER-FACEOPTION IS NOT IUPC.

WSMLC_D_0002 WSMLC Delete WSMLC cannot be deleted, because it is still being used by one or more WLCSEs.

WSMLC CANNOT BE DELETED, BECAUSE IT IS STILL USED BY ONE OR MORE WLCSES.

WSMLC_D_0003 WSMLC Delete If the parent WBTS has WBTS-BroadcastSIB15 as Enabled, the WLCSE cannot be deleted for a cell.

WLCSE CAN NOT BE DELETED FOR A CELL IF ITS PARENT WBTS HAS WBTS-BROADCASTSIB15 AS ENABLED


Object type

Operation type


Table 39 WSMLC consistency checking rules (Cont.)

Date post:	26-Oct-2014
Category:	Documents
Upload:	tarekgara
View:	462 times
Download:	22 times

Checking Rules

Documents