Photo: Bryn Hughes Sledder: Dan Treadway

Part# TR04

Photo: Russell Dalby Sledder: Aaron Leyland

The CFR Tunnel racks are designed to go on the back of mostsnowmobiles with a141” or longer tunnel. They are made from strongyet lightweight structural tubular aluminum. The CFR Tunnel racks aredesigned to carry extra fuel, backpacks, ski boots etc. CFR also

manufactures a complete line of waterproof bags that are designed tofit seamlessly with our racks, to keep your gear extra dry. If you needto carry skis, snowboards or pow surfers we offer a complete line ofto carry skis, snowboards or pow surfers we offer a complete line ofbrackets that bolt to the side of our racks to keep your gear secure and

out of your way.

We are constantly working on making our products line better andbetter. This year is no exception, and the new Mountain rack is as cutting edge as it gets. The overall height of the Mountain Rack is only3.75 “. Dropping the center of mass lowers all of the weight that’s carried in the rack allowing the snowmobile to perform better under load.Another new feature of this rack is that the new design allows the rackto be mounted on the edge of the tunnel. This will allow some OEMto be mounted on the edge of the tunnel. This will allow some OEMfactory holes to be used requiring less drilling into the rear tunnel.Thenew design is also engineered to use fewer materials than existing racksyet still be as strong.

Part# TR03

Rack Dimensions : 15x10.75x2mounting plate 2.75x10.9

The iRack from CFR has been our flagship rack for the past three years. The new CFR Connect system was designed using the iRack because of its strong yet lightweight design. Features include- Now available with CFR Connect system. Allows rack to be put on and taken off snowmobile without any tools.. (Only available on Ski Doo XPand XM snowmobiles.and XM snowmobiles.- Made from extremely strong and lightweight ¾” structural tubularaluminum.- Mounting brackets are from fitted around the sides of rack for superstrength.- Professional welds for long lasting results.- All mounting hardware included is made from high grade stainlesssteel. (Super strong and rust free)steel. (Super strong and rust free)- Carries up to a 20l 6 G fuel container.- Carries up to two pairs of skis, Snowboardsand Pow Surfers with proper attachments.(Sold separately)- Mounts to most snowmobiles with a 141”track or longer.-- Compatible with CFR Dime and QP Bag.- Available in Four Colors: Flat Black, Monster green Ghost White and orange crush.

The Boardski bracket kit is a direct result of listening to numerouscustomers and dealers wanting a bracket that carries skis or snowboards.The boardski bracket kit can carry one snowboard or one pair of skisand poles on the side of a snowmobile. Its the go to bracket for peoplewho both ski and snowboard or have friends that ski and snowboard.Nothing has been compromised in the design securing both skis orsnowboards. The Boardski fastens both skis and snowboards as well assnowboards. The Boardski fastens both skis and snowboards as well asall of the other ski/snowboard specific CFR Brackets.

CFR Bracket Kits are designed to be attached to the CFR Mountain rack,iRack, DD and D racks. Each CFR Bracket kit is designed to carry skis,snowboards, no boards and Powsurfers. The bracket kits attach to theside of the CFR racks enabling up to two bracket kits to be attached to each rack.(Using the single ski bracket system only allows one bracket

kit to be used)

Features:

Carries one pair of skis/poles or one snowboard.Light weight Nylon parts are infused with resin thatmakes them extremely strong and can handle -100 degreecold temps.

Custom made Injected molded straps that wont break in the cold but will break insevere roll overs to prevent damage.severe roll overs to prevent damage.Ratchets and Ladders are custom made for superior ratcheting capabilities.All mounting Hardware included is made from high grade stainless steel.(Super strongand rust Free) Carries one pair of skis and poles.(Another Dual Ski bracket kit can be purchased tocarry up to two pairs of skis)Specifically designed to be fastened to CFR DD, i rack or Mountain Rack (Sold separately)Proudly made Canada.Proudly made Canada. Photo: Kurtis Croy Tandemars: Willy and Dave

part # K04

Features:

Light weight Nylon parts are infused with resin that makes them extremely strong andcan handle -100 degree cold temps.Injected molded straps that wont break in the cold but will break in severe roll overs toprevent damage.Ratchets and Ladders are custom made for superior ratcheting capabilities.All mounting Hardware included is made from high grade stainless steel.(Super strongAll mounting Hardware included is made from high grade stainless steel.(Super strongand rust Free) Carries one snowboard.(Another bracket can be purchased to carry up to two snowboards) Specifically designed to be fastened to CFR D , DD rack , iRack or Mountain rack (Sold Separately) Proudly made in Canada. Proudly made in Canada.

part# K01

photo: Joe Carter Mountain Slayer: Bryan Iguchi

The snowmobile Snowboard rack that is tested and approved byprofessional snowboarders Travis Rice, Mark Carter, Mark Landvik andAnnie Boulanger. The CFR Snowboard Bracket Kit will keep yoursnowboard out of the way while snowmobiling. You will forget thatyou have your snowboard with you when breaking trail to the top ofyour favorite snowboard line or jump spot. This package contains partsand hardware to carry one snowboard on D, DD rack, iRack orand hardware to carry one snowboard on D, DD rack, iRack orMountain Rack (Sold separately)Another snowboard bracket kit can be purchased to carry up to twosnowboards on the D, DD, i Rack or Mountain Rack. A CFR Dual Ski Bracket can also be purchased to carry a pair of skis onDD or iRack.(Sold separately) A boardski Bracket Kit can also bepurchased to carry either a pair of skis and or snowboard on DD, iRackor Mountain Rack(Sold separately)or Mountain Rack(Sold separately)

The CFR single ski brackets system is designed to be mounted to D, DD, i rack or Mountain Rack. The CFR single ski bracket kit is the best wayto get your skis and poles to the top of the mountain safely on yoursnowmobile. This set up evenly distributes the weight of both skis andpoles by carrying one ski and pole on each side of the D, DD,i rack orMountain Rack. No other attachments are possible.

part# K03

Features:

Light weight Nylon parts are infused with resin that makes them extremely strong andcan handle -100 degree cold temps.Custom made Injected molded straps that wont break in the cold but will break insevere roll overs to prevent damage.Ratchets and Ladders are custom made for superior ratcheting capabilities.All mounting Hardware included is made from high grade stainless steel.(Super strongAll mounting Hardware included is made from high grade stainless steel.(Super strongand rust Free) Carries one ski and pole on each side of snowmobile. No other Brackets can be usedwith this system. Specifically designed to be fastened to CFR D/DD rack, i Rack or Mountain Rack(Sold separately)(Sold separately)Proudly made in Canada.

Photo: Bryn Hughes Sledder: Dan Treadway

Tested and approved by professional Skiers Dan Treadway,Ian McIntosh,Dana Flahr and Sage Cattabriga. The CFR Dual Ski Bracket Kit will keepyour skis and poles out of the way while breaking trail to your favoriteline or jump spot. This system can be used with another dual ski bracketkit to carry up to two pairs of skis and poles. It also can be used with asnowboard bracket kit to carry a snowboard on one side of snowmobileand skis/poles on the other side of snowmobile. When two dual skiand skis/poles on the other side of snowmobile. When two dual skibracket kits are being used it is putting a lot of extra weight on the reartunnel. Slow down going through rough conditions. Extra tunnelsupports are a good idea if you frequently travel in rough conditionswith two pairs of skis.The Dual Ski Bracket kit is specifically designed tobe attached to the CFR DD rack, i rack or Mountain Rack(Sold separately)

Photo: Bryn Hughes

part# K02

The new CFR Snowboard/Pow Surf bracket is a result of a directcollaboration with Jeremy Jensen at Grassroots pow surfing and CFR.Jeremy needed a rack on his snowmobile to carry his pow surfers. The current CFR snowboard bracket kit he had been using workedgreat for his snowboard but didn’t work with his pow surfers. We hitthe drawing board and designed a new bracket that worked both tocarry his revolutionary bindingless snow riding pow surfers and hiscarry his revolutionary bindingless snow riding pow surfers and hisregular snowboard when he had to use bindings. If you want to carryyour pow surfer or snowboard on your snowmobile this is the bracketfor you!

Features:Carries one Grass Roots pow surf board or one snowboardLight weight Nylon parts are infused with resin that makes them extremely strong andcan handle -100 degree cold temps.Custom made Injected molded straps that wont break in the cold but will break insevere roll overs to prevent damage.Ratchets are specifically made for this application with bigger pulling teeth and thickerRatchets are specifically made for this application with bigger pulling teeth and thickersprings. Made to last!All mounting Hardware included is made from high grade stainless steel.(Super strongand rust Free) Another bracket can be purchased to be mounted on the other side of the rack to carry whatever else you need.

Specifically designed to be fastened Specifically designed to be fastened to CFR D/DD rack, i Rack or Mountain Rack(Sold separately)Proudly made in Canada.

POV Photo: Jeremy Jensen

part# K05

part# B01

photo:foonskis.com sledder: db

The new CFR handlebar bag convenientlyattaches between the handlebars ofmost snowmobiles. The rip stop waterprooffabric along with waterproofzippers keep your goods dry on the wettest days. Using the CFR handlebarbag lets you empty your jacket and pant pockets, with them empty you canboondock your sled through the trickiest terrain and side hill for miles. boondock your sled through the trickiest terrain and side hill for miles. 9” of clearance required on XM snowmobiles between the top of the bag andthe DESS switch. If clearance is not available the bag will knock DESS switchout when turning sharply. DESS switch can be relocated if you still want torock the Buck bag and dont have clearance.

The CFR bag division was developed to utilize certain key spots on the snowmobile to carry much needed extra gear. Our goal was to only have theessentials in your back pack and pockets. Lightening up your load when

sledding and shredding is a must have for high performance maneuvers. Thebags are waterproof and tough to withstand all of the hardest winterconditions you will face and keep your gear dry and accessible.

Part# B03

The CFR Dime Bag was designed by Birkin, BC Canada based FYI designs. Tom Routhhead designer/snowboard legend/sled/moto head wanted a waterproof and supertough bag for his CFR rack. The Dime Bag was the result. Tom choseleading fabric maker Dimension Polyent for theouter shell because of its super tough andwaterproof characteristics. The CFR Dime Baghas velcro strips that wrap around all CFR rackshas velcro strips that wrap around all CFR rackstubular bars in four spots to keep the bag lockedinto place. The waterproof zipper on theoutside will keep your contents dry. The insidewaterproof pocket is perfect for your wallet andthe key hook keeps your keys in the right place.A CFR scraper comes standard in all Dime Bagsso you can scrape the unwanted ice build up onso you can scrape the unwanted ice build up onyour snowboard/skis and running boards. TheCFR Dime Bag allows 10 cubic inches of carryingcapacity. Now you can bring along your first aidkit, tow rope,syphon hoses, beverages orwhatever else you might need for your winteradventures.

photo:DB

part# B02

Features include

-Cordura waterproof fabric-Waterproof zippers-25 liter capacity, unzip the extension and capacity increases to 50 liters-Clips right into all CFR rack systems and is easily systems and is easily removable-Shovel access on top allows easy access to shovel on deep days.-Covenient carrying handle-Individual inside pocket

photo:totallyawsomeadventures.com sledder: Dave Treadway

The new CFR QP Bag offers 25 litres of waterproof carrying capacity and fitssnugly in all of the CFR rack systems. The QP is a telescoping bag that doublesin size with a quick zipper extension to carry up to 50 litres of gear.

part# M03

Features include

-Bolts to the side of most snowmobiles (Does not work on 07 and newerPolaris or Skidoo Rev’s)-Two nylon infused polyurethane brackets carry snowboard and or skissecurely and safely.-Custom made injection moulded nylon straps keep your shit tight.-Cfr uses custom ratchets designed to be used under very high tensile loads-Cfr uses custom ratchets designed to be used under very high tensile loadswith thicker springs andratcheting mechanisms.-CFR logo included!-Carries either a pair ofskis or snowboard.-Another DTM Boardskibracket system can bebracket system can bepurchased to carry anotherset of skis or a board on theother side of your sled.-Top vertical holes line up withpre drilled Ski Doo XM’s hole pattern.

photo: Russell Dalby Sledder: Curtis Ciszek

The CFR direct tunnel mount (DTM) rack systems are designed to be attacheddirectly to the rear tunnel of most snowmobiles. No other rack required. Theyare for the minimalist who doesn’t want a rack on the back and just wants tocarry their snowboard or ski gear.

We have been working on thedirect tunnel mount bracketfor the past 5 years. The countless moulds and R&D havemade this our biggest projectto date. We are happy to finally bring youthe new DTM Boardski bracket system.the new DTM Boardski bracket system.The demands and expectations of ourusers of this system are huge. That’swhy this release is such great news; it has all the quality and features that our customershave been demanding. The ability to carry a snowboard or skis with no otherrack required is now a reality. Just buy this bracket, bolt it on, strap on yourskis or board and go! skis or board and go!

The snowboard rack tested and approved by snowboarders EricJackson, Bjorn Leines and Mads Johnson. Lightest snowboard bracketson the market weighing in @ 2.5lbs.Tandem riding with your buddies isnow easy as pie with your snowboards on the rack and not in your backpacks hitting you in the back of the head. Having snowboards fastenedto the snowmobile allows you to negotiate tricky snowmobilingsituations getting to your favorite big mountain line or jump spot. Thesituations getting to your favorite big mountain line or jump spot. TheMetal Snowboard rack system is made for the minimalist who wants tobe able to carry his or her snowboard and nothing else. The CFR MetalSnowboard rack System carries one snowboard on the side of yoursnowmobile. (No other rack required) Another Metal Snowboard rackSystem can be purchased to carry two snowboards.

part# M01

photo: Kurtis Croy Shredder: db

Features:

-Metal Snowboard rack System carries one snowboard on the side of most snowmobiles(No other rack required) -Another snowboard can be carried by purchasing another Metal Snowboard rackSystem.-A cost effective way of carrying a snowboard on your snowmobile.-Light weight Nylon parts are infused with resin that makes them extremely strong and-Light weight Nylon parts are infused with resin that makes them extremely strong andcan handle -100 degree cold temps.-Custom made Injected molded straps that can handle temps as low as -100 cold butwill break in severe roll overs to prevent damage.-Ratchets and Ladders are custom made for superior ratcheting lock down.-All mounting Hardware included is made from high grade stainless steel.(Super strongfrom high grade stainless steel.(Super strongand rust Free) -Proudly made in Canada.

Features:

-Metal Ski Rack System carries one ski and pole on each side of most snowmobiles(No other rack required) -A cost effective way of carrying your skis and poles on your snowmobile.-Light weight Nylon parts are made from extremely strong infused resin that can handle -100 degree cold temps.-Custom made Injected molded straps that will not-Custom made Injected molded straps that will notbreak in -100 degreecold but will break in severe roll overs toprevent damage.-Ratchets and Ladders are custom made forsuperior ratcheting lockdown.-All mounting Hardware included is made-All mounting Hardware included is madefrom high grade stainless steel(Super strong and rust Free) -Proudly made in Canada.

part# M02

The CFR Metal ski Bracket System is one of the lightest snowmobile skiracks available today @ 5lbs.(No other rack required)This is the minimalist set up, for a person who only wants to carry oneski and pole on each side of there snowmobile. Having skis fastened tothe snowmobile allows you to negotiate tricky snowmobiling situationsgetting to your favorite big mountain line or jump spot. The CFR Metalski rack would be a cheaper alternative to CFR tunnel racks using theski rack would be a cheaper alternative to CFR tunnel racks using theDual Ski Bracket / Single Ski Bracket kits.

photo: Mark Fisher

Flat Black part# CD01

Monster Green part# CD02

Ghost White Part# CD03

Features include

-2” rise - 7 degree Up- 12degree Back- 30” width-Made from 7075 Heat treated super aluminum with flex technology-Strong ,lightweight and tough as shit!-Better positioning than stock bars and way stronger! The new designdissipates bumpy conditions better than stock bars keeping you fresh andriding longerriding longer-Vertical and horizontal positioning graphics for perfect centering and pullback angulation.-All handlebars come with CFR bar pad

The CFR snowmobile control division was started because of the lack offeatures and designs of handlebars and risers that were available on the

market. All of the products below have been designed and approved by us atCFR and our circle of Team riders and users.

Introducing the Boondocker Bar!The new cutting edge snowmobiles that have been released in the past fewyears require less effort and therefore the design of the handle bar needed tochange. Designed from feedback from our network of Team riders and usersthe Boondocker by CFR is the result! Do you love to ride in deep pow, lay bigpow carves manoeuvring through tight trees and whip off every jump insight? Is your snowmobile your helicopter for accessing powder snow eithersight? Is your snowmobile your helicopter for accessing powder snow eitherfor skiing or snowboarding? The CFR Boondocker with its 30 inch width, 12degree sweep and 7 degree bar rise was made for you. This bar was designedfrom the inside out.First of all we used 7075 double butted heat treatedaluminum for a strong yet lightweight base. In the center, where the stemclamps, we use a larger 1 1/8th wall thickness, but at the ends it tapers to 7/8”.This allows the energy to dissipate over a gradual tapering within the innercore. What’s the result? Much better strength, but also much bettercore. What’s the result? Much better strength, but also much betterdampening of hard hits and a better feel for what’s going on underneath youon the snow. The 7/8th tapering thickness also allows the snowmobilecontrols to fit directly on the bar. On the outside we added a side to side andforward backward template so you can center and clamp the bar just whereyou want it, without a tape measure. The 37 degree bar ends are great forkeeping your hands from slipping off the handlebar and putting you into atree! We wanted the Boondocker to last and look good with age so the flattree! We wanted the Boondocker to last and look good with age so the flatblack bars are anodized and the Monster green and Ghost white bars havea triple powder coated finish.

Flat Black part# CD04

Monster Green part# CD05

Ghost White Part# CD06

Features include

-3” rise - 8 degree Up- 14degree Back- 30” width-Made from 7075 Heat treated super aluminum with flex technology-Strong ,lightweight and tough as shit!-Better positioning than stock bars and way stronger! The new designdissipates bumpy conditions better than stock bars keeping you fresh andriding longerriding longer-Vertical and horizontal positioning graphics for perfect centering and pullback angulation.-All handlebars come with CFR bar pad

The CFR Dan Treadway signature bar is a result of A handlebar that isdesigned to do what Dan does best on his snowmobile. Pretty mucheverything if you have seen his video parts or pictures, but more specific tojumping his snowmobile off of big stuff. The 30” width is stable on the biggestdrops with the strait ends allowing full use of the entire bar. The DanTreadway Bar specific 3” rise 8 degree up and 14 degree back bar specs is ofDans liking. If you like the specs but want to have bar ends there are marks onDans liking. If you like the specs but want to have bar ends there are marks onthe end of the bar that allows you to evenly cut down the bars and putaftermarket hooks on them. Or if you want narrower bars you can just cutthem down to your desired width. This Bar was designed from the inside out.First of all we used 7075 double butted heat treated aluminum for a strongyet light weight base. In the center, where the stem clamps, we use a larger 1 1/8”wall thickness, but at the end the bar tapers to 7/8”.This allows theenergy to dissipate over a consistent and gradual tapering within the innerenergy to dissipate over a consistent and gradual tapering within the innercore. What’s the result? Much more strength, but also much better dampeningof hard hits and a better feel for what's going on underneath you on the snow.The 7/8” tapering thickness also allows the snowmobile controls to fit directlyon the bar. On the outside we added a side to side and forward backwardtemplate so you can center and clamp the bar just where you want it withoutusing a tape measure. We wanted the bar to last and look good with age sothe Black Bar is Anodized and the White and Green bars have a Powderthe Black Bar is Anodized and the White and Green bars have a Powdercoated finish that’s triple layered. The Dan Treadway signature model comesin three colors. Flat black, Monster green and ghost white.

Part# 4” CD07 5” CD08 6” CD09 7” CD10 8” CD11

Features include-- CNC machined from Hi strength 6061 - T06 Aluminum.- Graphics are laser etched for a durable long lasting look.- Anodized black and tumbled finished.- Available in 4,5,6,7 and 8” inch heights.- Will work with either 1-1/8" tapered bar or 7/8"bars. (Adaptor included)- Patent pending ?” anti slip insert keeps bars where you want them.- Patent pending ?” anti slip insert keeps bars where you want them.- You must have a pivot style steering post or a double pivot adapter.- Designed to be used with the new CFR Boondocker/DT bars but will workwith all handlebars.

The new Knucks Handlebar risers are ideal to personally customize the height of yourbars. Machined from Hi Strength super tough 6061 - T06 Aluminum they cantake anything you can throw at them. An anodized black tumble finish andGraphics kit will ad some style to your steed. The graphics are not just forlooks with a centering line on the top cap allowing you to adjust your handlebars to where you want them! The Knucks come in 4,5,6,7 and 8 inch heightsbars to where you want them! The Knucks come in 4,5,6,7 and 8 inch heightsand will work on your 7/8” or oversized 1 1/8” bars

Part# C01

Photo: Rob Alford sledder: Chris Brown

The CFR Connect System enables you to take your CFR iRack on or off at whim!Four stainless steel buckles lock your rack down to your snowmobile.

-4 Stainless steel buckles lock your rack down to your snowmobile tunnel.-Permanent Mounting points on snowmobile are low profile stainles steelloops.-Made for people who sometimes want to Go lightweight and low pro.-CFR Connect only works with the CFR iRack and on Ski Doo XP and XMsnowmobiles Only.

Add a bit more Metal to your rear snowmobile tunnel. These bad boysad 50% more strength to your tunnel. You can mount them on theinside or outside depending on what snowmobile you have. Blades arerecommended if you travel on very bumpy roads with a lot of extraweight on your rear tunnel. Blades are available for Ski Doo XP's andXM’s. 06-07 Arctic cat M series and Yamaha Nytro's.Features:Features:- Ski Doo XP/XM Blades are anatomically designed to fit the rear tunnelof the Ski Doo XP/XM.Part # TS01 146" Track.Part # TS02 154" TrackPart # TS03 163” Track- Nytro Blades square off the rear tunnel leaving a flat platform tomount rack to.mount rack to.Part # TS04 2010-2013 Yamaha NytroPart # TS05 2008-2009 Yamaha Nytro- 06-08 Arctic Cat Blades go on dimples that are on top of tunnelallowing a flat surface for rack to sit on.Part # TS06 2008-2009 Arctic Cat- All Rivets and mounting hardware included.

Photo:Dave b . Joe Lax Patiently waiting for the fog to clear

Prevents overheatingExtends the life of your sliders

CFR Aluminum Black Ratchet Part # 1006

16" Injected molded replacement strap. Part # 1002

8" Injected molded replacement strap. Part # 1001

220mm CFR Ladder strap Part # 1003

Photo: Bryn Hughes Sledder: Dan Treadway

-High quality alluminum ramps-folding feature and lightweight enhancesportability rubber coated arms protect truck bed -unique channel system to diffuse loading stress away from welds-models to fit in shortbox and regular-models to fit in shortbox and regularbeds-3 year warranty on deffectsin material andworkmanship -available in 2 lengthsMade in the USA

part# AR01 6 ftpart# AR02 7 ft

Photo: Bryn Hughes Sledder: Dan Treadway

photo:Bryn Hughes sledder:Dan Treadway

studio photos: Dice K ,Brian HockensteinBrochure: Corbett

For more info orordering please visitwww.cheetahfactoryracing.comor call (604)894-18801-877-894-1880