Chip Programmer Intelsteer Power Save PBI Series.

Chip Programmer

Intelsteer Power Save PBI Series

Chip Programmer

• Main Menu- Basic Applications• The chip programmer is inbuilt with 13 different

kinds of basic application setups • Including conveyer belt 、 compressor 、 stone

crusher 、 and so on ….

Chip Programmer Main Menu- Basic Applications

• Stone crusher-provided with a function of full-torque start

Line voltage

25%

80%100%

Time

start 1

Optimization

start2

Dwell Time

Optimization

Dwell Time

Chip Programmer

• Basic software reboot• The independent soft start

parameters can be adjusted by the chip programmer.

Chip Programmer Main Menu- Basic Soft Reboot

• Basic voltage—voltage value at the time of start

• From 25 to 80%V (may increase gradually at a ratio of 1%)

• Directly start torque from 6 to 64%

(6)25%

(64)80%pedestal voltage

start torque

• Start Time• 0-255 seconds (may increase gradually at 1

sec. value)

Time

(6)25%

(64)80%pedestal voltage

start torque

0 255

100%



• Kick start level and time• Directly start torque with line

voltage from 25 to 80% or from 6 to 64%.

• 0.1 to 25 seconds (may increase gradually at 0.1 sec. value

(6)25%

(64)80%

Kick start voltage

levelK

ick start torque

0 10

100%

(36)60%1


• Current limitation level and time• Directly start current from 25 to 80%• 0 to 255 seconds (may increase

gradually at 0.1 sec. value)

Current limitation Time

Start current level

0 40

25%

80%100% 100%

Motor V

oltage

Start Time


• Soft stop function• Step-type stop

function• Reverse Torque

Braking


• Soft stop function

• Soft stop time has effect merely on high electrostatic frictional load (e.g. pipeline centrifugal water pump). The principle of operation is, on the basis on the gradual reduction of terminal voltage of motors, controlling motor torque to allow for the deceleration of motors in a controlled state with their own loads.


• A =Step-type stop voltage level (may be adjusted from 100 to

40% at an increase/decrease ratio of 1%)

• B = Step-type stop time (may be adjusted from 0 to 255 seconds at an increase/decrease ratio of 1 second)

• C = Step-type stop power dump level (may be adjusted from 30 to 50% at an increase/decrease ratio of 1%)

(64)80%

100%

Step-type stop function

(6)25%

Voltage

Motor torque

0 255

A

B

C

Actual working conditions of water pump after the application of step-type stop function

Process

start running stop

Time

Start Soft Start Stop Soft Stop



• PLUG BRAKING (REVERSE TORQUE BRAKING)

Line voltage

625%

80%100% B

raking torque%

time

Contactors reverse

64

Forward Optimize Braking Time


• A = braking torque （ may be increased gradually from 6 to 64% at a ratio of 1%)

• B = braking time （ may be increased gradually from 0 to 255 seconds with a value of 1 second)

PLUG BRAKING (REVERSE TORQUE BRAKING)

625%

80%

100%

Braking torque

time

Con

tactors R

everse

64

Forward Optimize Braking Time

A

B

U V W

L1 L2 L3

EARTH

K1

FAN(If Fitted)

3 Phase Supply

U WV

K2

Motor Overload

Semiconductor Fuses

PowerbossPBI series

Line of main power supply

* Normally Closed Contact from optional speed sensing relay*.

Intelsteer power save PBI seriesTB1

123456

110V/230VControl Supply

K1

Start

TB3

123456

RL2

FAN(if fitted

Emergency Stop

O/L

K2

K1

For

K1Brake

*Brake

TB2RL1

123456

Line of control circuit

REVERSE TORQUE BRAKING



• Relay RL1 and RL2 can be set in any of the following states:

• Operational relay• Relay with maximal

rotate speed• Fault relay


• Shifting function of non － arcing touch

• After the formation of start loop, “IntelSteer electric appliance” can provide a buffering time before current runs through the motor and make the main contactor (K1) actuate under a zero-current condition.

• It may increase or decrease from 0.1 to 25.5 seconds at a ratio of 0.1 second.

Date post:	13-Jan-2016
Category:	Documents
Upload:	suzanna-norris
View:	223 times
Download:	5 times

Chip Programmer Intelsteer Power Save PBI Series.

Documents