FX350 / FX350B

(with FX350B)

Please read through this booklet for safe and efficient use of the applianceeven if you are familiar with using this appliance.

Keep this guide handy for future reference.

First Use Safety Recommendation

Chopper (FX350) / Chopper Blender (FX350B)

-2-

While using electrical appliances, in order to reduce the risk of fire, electric shock,and/or injury to persons, basic safety precautions should be followed, including thefollowing:

• Read all instructions carefully.

• To protect against electrical shock, DO NOT IMMERSE the appliance, cord set orplug water or other liquids.

• Close supervision is necessary when any appliance is used by or near children.

• Unplug from outlet when not in use. Unplug before cleaning, changingaccessories or approaching parts which move in use.

• Never pull the cord when unplugging from the power outlet.

• Do not operate any appliance with a damaged cord or plug, or after the appliancemalfunctions or has been damaged in any manner. Return appliance to anauthorized service facility for examination, repair or adjustment.

• Do not abuse the cord. Never carry the appliance by the cord or pull it todisconnect it from the power outlet. Always grip the plug & pull to disconnect.

• Do not use outdoors.

• Do not let cord hang over edge of table or counter, or touch hot surfaces.

• Do not place on or near a hot gas or electric burner, or in a heated oven.

• Do not use the appliance for other than the intended use.

• The use of accessory attachments not recommended by this appliancemanufacturer may cause hazards.

• For household use only.

• Do not leave this appliance unattended in use.

• To avoid a circuit overload, do not operate another high wattage appliance on thesame circuit.

• If an extension cord is used, please ensure it is correctly wired and rated for usewith this appliance. If in doubt, consult a qualified electrician. The extension cordshould be arranged so that it will not drape over the counters or table tops whereit could be pulled by children or tripped over.

• Do not attempt to repair this appliance yourself; instead take it to your nearestBlack & Decker-owned or Authorised Service Centre for repair.

IMPORTANT SAFEGUARDS

SAVE THESE INSTRUCTIONS

ENGLISH

-3-

Parts Identification

1. Blender lid cap (FX350B)

2. Blender lid (FX350B)

3. Blender jar (FX350B)

4. Blender Blade (FX350B)

5. Cover

6. Chopper Blade

7. Bowl

8. On / Off switch

9. Motor housing

10. Blade release button

FEATURES

• 700W

• Single speed pulse operation

• 1 litre Blender jug (FX350B only)

• Brake

• Non-slip feet

• Stainless steel blades

ENGLISH

610

25

10

6

7

8

9

4

3

1

-4-

ENGLISH

Before first use:• Before using your Chopper Blender for the first time, make sure it is disconnected from the electrical supply,

then remove all packaging.• All parts should be cleaned before use.• Clean all parts as recommended in the section “How to take care of your Chopper/Chopper Blender”• The motor housing (9) must only be cleaned with a damp cloth, and dried thoroughly before use.• To clean the Blender jar (3), add 0.5L of warm water and a little detergent to the jar.• Fit the jar to the Motor housing & connect it to a suitable electrical supply.• Run the Blender for a few seconds until clean.• Rinse, repeat & rinse again.• Dry carefully, taking care when approaching the blades as these are very sharp.• All other parts can be washed using a mid detergent and warm water. These parts are not dishwasher safe

and must be hand washed.• After washing, rinse and allow all parts to dry thoroughly before re-assembly and storing.• Take care when handling the cutting blades as they are sharp.How to assemble your Chopper (FX350)• Place the motor housing (9) on a flat, stable surface.• Place the bowl (7) over the stem on the motor housing.• Fit the blade (6) over the boss on the bowl. Press down gently to make sure it is locked in place.• Fit the cover (5) over the bowl; rotate anti-clockwise to lock in place.

Note: The chopper will not work unless the cover is correctly fitted.How to assemble your Blender (FX350B)• Place the motor housing (9) on a flat, stable surface.• Place the blender lid (2) on top of the blender jar; rotate anti-clockwise to lock in place.• Fit the blender lid cap (1) into the blender lid & rotate anti-clockwise to lock in place.• Place the Blender jar (3) on the motor housing and rotate it in an anti-clockwise direction until it locks in

place.Note: The blender will not work unless it is correctly fitted.

How to use your Chopper (FX350)• This appliance is designed to chop dry ingredients such as meat.• Do not use this appliance for any other purpose. For indoor domestic use only.• Prepare the ingredients by cutting them into small cubes and place them in the bowl (7). Do not over-fill the

bowl.• Fit the cover (5) over the bowl and rotate anti-clockwise to lock in place.• To avoid a hazard, this appliance must only be used for chopping dry ingredients.

Note: The chopper will not work unless the cover is correctly fitted.Press the on / off switch (8) down.• The unit should only be operated for 5 to 15 second pulses only. Never operate the chopper continuously

for longer than 45 seconds at a time. Always allow the appliance to cool down for a minimum of 15 minutesbefore next use.

• When the correct consistency is achieved, disconnect the unit from the electrical supply.• Remove the cover, the blade and then remove the bowl & transfer the ingredients to a suitable container.• Take care when handling the cutting blades as they are sharp.

-5-

ENGLISH

Protecting the environment

Separate collection. This product must not be disposed of with normal household waste.

Should you find one day that your Black & Decker product needs replacement, or if it is of no further use toyou, do not dispose it off with other household waste. Make this product available for separate collection.

Separate collection of used products and packaging allows materials to be recycled and used again.Use of recycled materials helps prevent environmental pollution and reduces the demand for rawmaterials.

Local regulations may provide for separate collection of electrical products from the household, at municipalwaste sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and recycling of Black & Decker products once they havereached the end of their working life. To take advantage of this service please return your product to anyauthorised repair agent who will collect them on our behalf. You can check the location of your nearestauthorised repair agent by contacting your local Black & Decker office at the address indicated in this manual.A list of authorised Black & Decker repair agents and full details of our after-sales service and contact areavailable on the Internet at: www.2helpU.com

How to use your Blender (FX350B)• Your Black & Decker blender has been designed for the following applications: blending, mixing and

crushing of solid and liquid food and beverage ingredients. This product is intended for household use only.• Prepare the ingredients and place them in the jar (3). Do not over-fill.• Fit the lid (2) over the bowl and the lid cap (1) to it, rotating both in an anti-clockwise direction to lock them

in place.• Place the Blender jar (3) on the motor housing and rotate it in an anti-clockwise direction until it locks in

place.• Do not open lid until the blades come to a complete stop.

Note: The blender will not work unless it is correctly fitted.Press the on / off switch (8) down.• The unit should only be operated for 5 to 15 second pulses only. Never operate the chopper continuously

for longer than 45 seconds at a time. Always allow the appliance to cool down for a minimum of 15 minutesbefore next use.

• When the correct consistency is achieved, disconnect the unit from the electrical supply.• Remove the jar from the motor housing. Remove the lid & pour the ingredients into a suitable container.• How to take care of your Chopper (FX350) / Chopper Blender (FX350B)• The appliance must be cleaned thoroughly after each use.• Make sure the appliance is switched ‘OFF’ and unplug the unit from the power supply before cleaning.

NOTE: NEVER IMMERSE the motor housing (9) IN WATER OR ANY OTHER LIQUID.• To clean motor housing, wipe clean with a damp cloth. Allow to dry thoroughly before re-using or storing.• To clean the Blender jar, add 0.5L of warm water and a little detergent to the jar.• Fit the jar to the Motor housing & connect it to a suitable electrical supply.• Run the Blender for a few seconds until clean. Rinse, repeat & rinse again.• Dry carefully, taking care when approaching the blades as these are very sharp.• All other parts can be washed using a mid detergent and warm water. These parts are not dishwasher safe

and must be hand washed.• After washing, rinse and allow all parts to dry thoroughly before re-assembly and storing.• Take care when handling the cutting blades as they are sharp.

ENGLISH

Black & Decker provides a 2 Year Warranty for this product from the date of purchase against defects due todefective materials or workmanship. Motor/element burn-outs due to voltage fluctuations are not covered underwarranty. If the product should become defective within the warranty period, Black & Decker will repair or (at Black &Decker's discretion) replace it free of charge.

The warranty provisions do not cover failure due to accident, misuse, abuse, negligence or non observation of localregulations on the part of the user. Equally, the warranty provisions do not apply where the appliance has beenserviced by a person not authorized by Black & Decker or serviced with non-approved parts and this has contributedto the fault of the product. Superseded models without a replacement equivalent will either be repaired or (at Black &Decker's discretion) replaced with another product of similar retail value.

UPON PURCHASE

Fill in the Warranty Registration Card with the original Authorized Dealer's stamp (indicating date of purchase) andattach your purchase receipt to it. Retain in case of claims in the future.

MAKING A CLAIM

Take your defective product together with the Warranty Registration Card & purchase receipt to your local serviceCentre. You can either do this in person or send it freight prepaid. If mailing or shipping your appliance, ensure that itis packed carefully in a sturdy carton with enough packing material to prevent damage. Include a note describing theproblem to the service Centre and be sure to give your return address.

DESIGNED FOR DOMESTIC PURPOSES ONLY.

BLACK & DECKER HOME APPLIANCE 2 YEAR WARRANTY

Afghanistan: Ishan National Co., Opp. Ministry of Justice, Kabul. Tel.: +93-2-2101727. Algeria: SARL Outillage Corporation, 04Route De Dely Brahim Cheraga, Alger. Tel.: +213-21-364363/508, Fax: +213-21-369667. Bahrain: Fawaz Al Zayani, P.O.Box26563, Adliya, Manama. Tel.: +973-17-715252/712756, Fax: +973-17-713789. Bangladesh: Ultra Corporation, 8, Kushol Centre,Uttara, Dhaka 1230. Tel.: +880-2-8919272/9756 Ext.28, Fax: +880-2-9887167. Egypt: Anasia Egypt for Trading S. A. E., P.O.Box2443, 110 Mostafa Refaat Street, Sheraton Heliopolis 11361, Cairo. Tel.: +20-2-2684159, Fax: +20-2-2684169. Ethiopia: TewfikSherif & Co. Ltd., P.O.Box 5583, Debre Zeit Road, Addis Ababa. Tel.: +251-1-651700/601, Fax: +251-1-650570. India: GryphonImpex Pvt. Ltd., D-6/4, Okhla Industrial Area, Phase-I, New Delhi-110020. Tel.: +91-11-26372602-4, Fax: +91-11-26372601. Iran:Tehran - Service Centre of Iran, No 510, South Karger Ave, Below Pasteur Sq. Tehran. Tel.: +98-21-6490608/0656/6407672. KishIsland: Cayhan Electric Co., No. 69, Paradise Shopping Centre, Kish Island. Tel.: +98-76444-22894. Jordan: Bashiti Hardware,P.O.Box 1564, TLA Ali, Amman. Tel.: +962-6-5350009/4770741, Fax: +962-6-5350012/4789783. Kenya: Zylog Enterprises, IPSBuilding, Kuanda Street, P.O.Box 40877, Nairobi. Tel.: +254-2-338188/199, Fax: +254-2-330642. Kuwait: Al Omar Technical Co.,P.O.Box 4062, 13041 Safat, Kuwait. Tel.: +965-4848595/0039, Fax: +965-4845652. Lebanon: Est. F.A. Kettaneh SA, P.O.Box110242, Dora Highway, Kettaneh Building, Beirut. Tel.: +961-1-255860/6, Fax: +961-1-255891. Libya: El Ghoul Brothers, P.O.Box348, Islamic Call Bldg., Office 201-202, Benghazi. Tel.: +218-61-9097681/4183, Fax: +218-61-9094123. Madagascar: GroupTana Confort S. A. R. L., B. P. 1770, Antananarivo. Tel.: +261-20-2264505, Fax: +261-20-2264244. Malta: John G. Cassar Ltd.,36 Victory Str, Qormi QRM 06, Malta. Tel.: +356-21-493251, Fax: +356-21-483231. Mauritius: Happy World Marketing Ltd., Block2, Industrial Estate, Coromandel, P.O.Box 429, Port Louis. Tel.: +230-2076700, Fax: +230-2337330/7400. Nepal: UniversalTrading Centre, P.O.Box 1947, Tripureswor, Kathmandu. Tel.: +977-1-262192/260587/785, Fax: 261154. Nigeria: Amin Bros. Eng.Co. Ltd., 30A (Plot 1291), Akin Adesola Street, Victoria Island, Lagos. Tel.: +234-1-3201778, Fax: +234-1-2613667. Oman: OmanMktg. & Service Co., P.O.Box 2734, Ruwi, Muscat. Tel.: +968-560232, Fax: +968-560255. Pakistan: Karachi - Ammar Service &Spares, 60, Bank Arcade, Serai Road, Karachi. Tel.: +92-21-2426905, Fax: 2427214/5243. Pakistan: Lahore - Electronics Inn,212-G Raja Centre, Main Market, Gulberg, Lahore. Tel.: +92-42-5756750. Philippines: Modern House International Enterprises,213 Rizal Ave. Extension, between 2nd and 3rd Ave. Kalookan City. Tel.: +632 366-4487, Fax: +632 366-4489. Qatar: Al MuftahTrading & Cont., P.O.Box 875, Doha. Tel.: +974-4650880/4446868, Fax: +974-4441415. Saudi Arabia: Dammam - EbrahimFawaz Al Zayani, P.O.Box 76026, Al Raka, Dammam. Tel.: +966-3-8140914, Fax: +966-3-8140824. Jeddah: Anasia - P.O.Box50959, Jeddah - 21477. Tel.: +966-2-6710014, Fax: +966-2-6725929. EAC (Al Yousuf) - P.O. Box 30377, Jeddah - 21477. Tel.:+966-2-6519912, Fax: +966-2-6511153. Madina: Garziz Trdg. for Bldg. Mat.&Decor., P.O.Box 3364, Madina. Tel.: +966-4-8261490/8227636, Fax: +966-4-8265741. Riyadh: Anasia, P.O.Box 18689, Riyadh - 11425. Tel.: +966-1-2693751, Fax: +966-1-4501178. Yanbu: Bin Afif, P.O.Box 530 Yanbu, Al Bahr. Tel.: +966-4-3222626/8867, Fax: +966-4-3222210. Sri Lanka: DelmegeGen. Equip. Pvt. Ltd., No. 428/1AT. B., Jaya Mawatha (Darley Road), Colombo-10. Tel.: +94-11-2665914, Fax: +94-11-2665915.Sudan: United Distribution Company, P.O.Box 325, Sayed Abdul Rehman Street, Khartoum. Tel.: +249-11-772612/777296, Fax:+249-11-770919. Tanzania: General Motors Investment, P. O Box 16541, 14 Vingunguti Nyerere Road, Dar Es Salaam. Tel.: +255-22-2862661/5022, Fax: +255-22-2862667/5412/3. Tunisia: STE Tunisienne De Quincaillerie Stq., Nvelle Z.I 2013, Ben Arous,Tunis, Tunisia, Tel: +216 71386102, Fax: +216 71380412. UAE: Abu Dhabi - Light House Electric., P.O.Box 120, Abu Dhabi. Tel.:+971-2-6726131, Fax: +971-2-6720667. Dubai - Black & Decker (O) A.G., P.O.Box 5420, Dubai. Tel.: +971-4-7028234/233, Fax:+971-4-2822765. Ideal Mach. & Equipt. R. W/shop P.O.Box 37116, Al Quoz, Dubai. Tel.: +971-4-3474160, Fax: +971-4-3474157.Sharjah - McCoy Middle East LLC, P.O.Box 20228, Sharjah. Tel.: +971-6-5336321, Fax: +971-6-5336320. Uganda: The BuildingCentre, Kitgum House, 52 Station Road, P.O.Box 7436, Kampala. Tel.: +256-41-234567, Fax: +256-41-236413. Yemen: Aden -Middle East Trad. Co. Ltd., Mulla Dakka, Aden. Tel.: +967-2-240950, Fax: +967-2-240952. Sana'a: Middle East Trad. Co. Ltd.,P.O.Box 12363, Hayel Street, Sana'a. Tel.: +967-1-204201, Fax: +967-1-204204. Taiz: Middle East Trad. Co. Ltd., Campa areanear Al-Kair mosque, Taiz. Tel.: +967-4-231610/232033, Fax: +967-4-219869. Zimbabwe: J.D.Distributors, P.O.Box 226, 17Bessemer Road, Graniteside, Harare Tel.: +263-4-753913-7, Fax: 753918.

Names & Addresses for Black & Decker Service Concessionaries

WARRANTY REGISTRATION CARD