Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)First Published: 2017-08-04
Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000 800 553-NETS (6387)Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITEDWARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITHTHE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain versionof the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDINGANYOTHERWARRANTYHEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS"WITH ALL FAULTS.CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OFMERCHANTABILITY, FITNESS FORA PARTICULAR PURPOSEANDNONINFRINGEMENTORARISING FROMACOURSEOFDEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUTLIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERSHAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, networktopology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentionaland coincidental.
This product includes cryptographic software written by Eric Young ([email protected]).
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (https://www.openssl.org/)This product includes software written by Tim Hudson ([email protected]).
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: https://www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnershiprelationship between Cisco and any other company. (1110R)
Please send general FSF & GNU inquiries to [email protected]. There are also other ways to contact the FSF. Please send broken links and other corrections or suggestions [email protected]. Please see the Translations README for information on coordinating and submitting translations of this article.
Copyright © 2007, 2009, 2011 Free Software Foundation, Inc. Verbatim copying and distribution of this entire article are permitted worldwide, without royalty, in any medium, providedthis notice, and the copyright notice, are preserved. Updated: Date: 2011/06/28 02:44:32
© 2017 Cisco Systems, Inc. All rights reserved.
C O N T E N T S
P r e f a c e Preface lix
Audience lix
Document Conventions lix
Related Documentation lxi
Documentation Feedback lxi
C H A P T E R 1 Using the APIC CLI 1
Using the NX-OS Style CLI 1
C H A P T E R 2 A Commands 5
aaa authentication login console 8
aaa authentication login default 9
aaa authentication login domain 10
aaa authentication login fallback-check 11
aaa authentication login ping-check 12
aaa banner 13
aaa group server ldap 14
aaa group server radius 15
aaa group server tacacsplus 16
aaa user default-role 17
absolute 18
access-encap 19
access-group 20
access-list 21
account-status 22
action 23
active-flow-timeout 24
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) iii
address-family 25
address-pool-ref 29
address-pool 30
address-range 31
address 32
admin-state-enable 33
admin 35
advertise-subnet 36
aggregate-address 37
allow-credential 38
allow-origin 39
allow-promiscuous 40
allow-self-as 41
allow-writes 42
allowed-self-as-count 43
analytics 44
application 45
area default-cost 46
area interpod 47
area l3out 48
area loopback 49
area nssa 50
area nssa default-information-originate 51
area nssa no-redistribute 52
area nssa translate 53
area range 54
area route-map 55
area stub 56
arp 57
arp flooding 58
asn 59
attach-avs 60
attribute-logical-expression 61
attribute 62
authenticate 63
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)iv
Contents
authentication-key-timeout 64
authentication-key 66
authentication 69
auto-cost 72
auto-route-target 73
autonomous-system 74
C H A P T E R 3 B Commands 75
bandwidth 76
basedn 77
bash 78
bd-enf-exp-ip 79
bd-enforce 80
bfd 81
bfd ip ipv6 authentication 83
bfd ip ipv6 inherit 86
bfd ip ipv6 tenant 88
bgp-fabric 90
bgp 91
binddn 93
bpdu-filter 94
breakout 95
bridge-domain-match 97
bridge-domain 98
C H A P T E R 4 C Commands 101
callhome 104
callhome test info notice emergency alert critical error debug warning node 105
catalog-version 106
cdp 107
cert-chain 111
cert 112
certificate 113
channel-group 114
channel-mode 116
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) v
Contents
ciphers 119
clear-encryption-key 120
clear-pwd-history 121
clear core-status controller 122
clear core-status switch 123
clear core controller 124
clear core switch 125
clear endpoints leaf tenant bridge-domain 126
clear endpoints leaf tenant bridge-domain vlan 127
clear endpoints leaf tenant vrf 128
clear firmware 129
clear snapshot file 130
clear snapshot job 131
clear techsupport controllers 132
clear techsupport switch 133
clear troubleshoot epext session report 134
clear troubleshoot eptoep session report 135
clock display-format 136
clock show-offset 137
clock timezone 138
cluster-device 139
cluster-interface 140
collect 141
comm-policy 142
community-list expanded 143
community-list standard 144
configure-avs 145
configure-dvs 146
configure 147
connection intra-service 148
connection intra-service service1 connector1 service2 connector2 copyservice 149
connection terminal provider consumer service 150
connection terminal provider consumer service connector copyservice 151
connection terminal provider consumer terminal provider consumer copyservice 152
connector 153
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)vi
Contents
console 154
consumer 155
contract-id 156
contract 157
contract consumer 158
contract deny 161
contract enforce 163
contract intra-epg 164
contract provider 165
controller-group 168
controller 169
coop-fabric 170
coop 171
copp-aggr 172
cos enable 173
cos value 174
cost 175
country 176
crypto aes 177
crypto ca 178
crypto keyring 179
crypto webtoken 180
csr 181
customer-id 182
C H A P T E R 5 D Commands 183
data 185
dead-interval 186
debug-switch 187
debug log reset 188
debug log set 189
decommission controller 190
decommission switch 191
default-information 192
default-originate 194
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) vii
Contents
delay 195
deny-mode 196
deploy-epg tenant application epg qinq 197
deploy-epg tenant application epg type 199
deploy-epg tenant application epg vlan 201
deployment-mode 203
descr 204
description 205
destination-port 227
destination-profile 228
destination 229
destination address 232
destination destip 234
destination epg 235
destination external-l3 epg tenant l3out epg 237
destination external-l3 epg tenant vrf epg 239
destination interface 241
destination tenant 242
dhcp option 244
dhcp relay policy 245
dhcpv4-server 248
dhcpv6-server 249
dhparam 250
direction 251
disable-connected-check 254
disable-peer-as-check 255
distance 256
dns 260
dnssearchsuffix 261
dnsservers 262
dnssuffix 263
dnssvr 264
dnssvrgrp 265
domain 266
dot1q-tunnel 268
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)viii
Contents
dscp 269
dsr-vip 271
dsr 272
C H A P T E R 6 E Commands 273
ebgp-multihop 276
echo-address 277
echo-mode 278
echo-rx-interval 279
email-addr 281
email-contact 282
email 283
enable-bfd 284
enable-ssl 285
encap-mode 286
encap 287
encryption 288
end 289
endpoint 290
endpoint ip 291
endpoint ip aging 292
endpoint ipv6 293
endpoint loop-detect action bd-learn-disable 294
endpoint loop-detect action port-disable 295
endpoint loop-detect enable 296
endpoint loop-detect factor 297
endpoint loop-detect interval 298
endpoint move-detection 299
endpoint retention bounce-age-interval 300
endpoint retention hold-interval 301
endpoint retention local-age-interval 302
endpoint retention move-frequency 303
endpoint retention policy 304
endpoint retention remote-age-interval 305
enforce-subnet-learning 306
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) ix
Contents
ep-flush 307
ep-retention-time 308
epg 309
eraseconfig 310
errdisable recovery cause bpduguard 311
errdisable recovery cause ep-move 312
errdisable recovery cause mcp-loop 313
errdisable recovery interval 314
erspan-id 315
erspan-version 317
evpn 319
evpn consumer 320
evpn export 321
evpn import 322
evpn provider 323
exec 324
exit 325
expiration 326
expires 327
export-config 328
export 329
exporter 331
extcommunity-list expanded 332
extcommunity-list standard 333
external-l2 334
external-l3 335
external-l3 epg 336
external-routed-domain 337
C H A P T E R 7 F Commands 339
fabric-external 341
fabric-interface ethernet 342
fabric-internal 343
fabric clear 344
fabric show 345
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)x
Contents
fail-auth-epg 346
fail-auth-vlan 347
fc 348
fcoe 349
fcoe fcmap 351
fcoe fka-adv-period 352
fcoe vsan vlan loadbalancing 353
fctimer e-d-tov 355
fctimer r-a-tov 356
feature 358
fex-interface-group 359
fex-profile 360
fex 361
file 363
filter 364
filter tenant bd 366
filter tenant vrf 367
fips mode 368
firewall-logging 369
firewall 370
firmware-version 371
firmware 372
firmware repository add 373
firmware repository delete 374
firmware upgrade controller-group 375
firmware upgrade switch-group 376
first-file 377
first-hop-security 378
first-hop-security security-policy 379
first-hop-security trust-control 380
first-name 381
flow-exporter 382
flow direction 383
flow exporter 384
flow monitor 386
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xi
Contents
flow node-policy 388
flow record 390
flow timeout collection 391
flow timeout template 392
flow vm-exporter 393
force-pwd-change 394
forged-transmits 395
format 396
forward-error-correction 397
C H A P T E R 8 G Commands 399
global-name 400
graceful-restart-helper 401
graceful-restart 402
group 404
C H A P T E R 9 H Commands 405
hello-interval 406
host-mode 407
host-rt-leak 408
hsrp delay 409
hsrp enable-bfd 410
hsrp group 411
hsrp use-bia 412
hsrp version 413
http 414
https 415
C H A P T E R 1 0 I Commands 417
idle-flow-timeout 424
immediacy-immediate 425
import-config 426
inband-mgmt 427
inband-mgmt epg 428
inherit-from-epg 429
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xii
Contents
inherit 431
inherit analytics-policy 438
inherit bfd 439
inherit bgp 440
inherit bgp address-family 441
inherit bgp dampening 442
inherit eigrp 443
inherit fc-fabric-policy 445
inherit fc-leaf-policy 446
inherit hsrp 447
inherit ipv4 448
inherit ipv6 449
inherit isis-fabric 452
inherit node-control-policy 453
inherit node-only 454
inherit ntp-fabric 455
inherit pod-group 456
inherit snmp-fabric 457
inherit vsan-attribute 458
instance 459
interface 460
interface ethernet 463
interface inband-mgmt0 465
interface mgmt0 466
interface port-channel 467
interface vfc-po 469
interface vfc 470
interface vlan 471
interface vpc 472
interpod 473
ip-inspection-admin-status 474
ip 475
ip address-range 478
ip address 480
ip address tenant application 484
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xiii
Contents
ip address tenant external-l2 486
ip address tenant external-l3 488
ip bandwidth 490
ip bfd 493
ip dhcp relay address tenant application 496
ip dhcp relay address tenant external-l2 499
ip dhcp relay address tenant external-l3 500
ip distribute-list eigrp 501
ip dscp 503
ip flow 505
ip hello-interval 509
ip hold-interval 512
ip igmp 515
ip igmp allow-v3-asm 516
ip igmp fast-leave 518
ip igmp group-timeout 520
ip igmp inherit 522
ip igmp last-member-query-count 524
ip igmp last-member-query-response-time 526
ip igmp querier-timeout 527
ip igmp query-interval 529
ip igmp query-max-response-time 531
ip igmp report-link-local-groups 533
ip igmp report-policy 535
ip igmp robustness-variable 537
ip igmp snooping 539
ip igmp snooping access-group route-map leaf interface ethernet ethernet vlan 540
ip igmp snooping access-group route-map leaf interface port-channel vlan 541
ip igmp snooping access-group route-map vpc context interface vpc vlan 542
ip igmp snooping fast-leave 543
ip igmp snooping last-member-query-interval 544
ip igmp snooping policy 545
ip igmp snooping querier 546
ip igmp snooping query-interval 547
ip igmp snooping query-max-response-time 548
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xiv
Contents
ip igmp snooping startup-query-count 549
ip igmp snooping startup-query-interval 550
ip igmp snooping static-group leaf interface ethernet ethernet vlan 551
ip igmp snooping static-group leaf interface port-channel vlan 552
ip igmp snooping static-group vpc context interface vpc vlan 553
ip igmp ssm-translate 554
ip igmp startup-query-count 555
ip igmp startup-query-interval 557
ip igmp state-limit 559
ip igmp state-limit reserved 561
ip igmp static-oif 563
ip igmp version 565
ip multicast 567
ip next-hop-self 568
ip ospf authentication-key 571
ip ospf authentication 573
ip ospf bfd 575
ip ospf cost 577
ip ospf dead-interval 579
ip ospf hello-interval 581
ip ospf inherit 583
ip ospf mtu-ignore 585
ip ospf network 586
ip ospf passive-interface 588
ip ospf prefix-suppression 589
ip ospf priority 591
ip ospf retransmit-interval 593
ip ospf transmit-delay 595
ip passive-interface 597
ip pim 600
ip pim auto-rp forward 601
ip pim auto-rp listen 602
ip pim auto-rp mapping-agent-policy 603
ip pim border 604
ip pim bsr bsr-policy 605
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xv
Contents
ip pim bsr forward 606
ip pim bsr listen 607
ip pim dr-delay 608
ip pim dr-priority 610
ip pim fast-convergence 612
ip pim hello-authentication 613
ip pim hello-interval 615
ip pim inherit 617
ip pim jp-interval 618
ip pim jp-policy 620
ip pim mtu 622
ip pim neighbor-policy 623
ip pim passive 625
ip pim register-rate-limit 626
ip pim register-source 627
ip pim rp-address 628
ip pim sg-expiry-timer 629
ip pim sparse 630
ip pim ssm route-map 631
ip pim state-limit 632
ip pim state-limit reserved 633
ip pim strict-rfc-compliant 634
ip pim use-shared-tree-only 636
ip prefix-list 637
ip prefix-list permit le 638
ip prefix 639
ip prefix permit le 640
ip router eigrp 641
ip router ospf default 643
ip shared address consumer 645
ip shared address provider 646
ip split-horizon 647
ip summary-address eigrp 650
ip throughput-delay 652
ip ttl 655
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xvi
Contents
ipobtainmode 657
iprange 658
ipv6-router 659
ipv6 660
ipv6 address-range 662
ipv6 address 664
ipv6 address tenant application 668
ipv6 address tenant external-l2 670
ipv6 address tenant external-l3 672
ipv6 bandwidth 674
ipv6 bfd 676
ipv6 dhcp relay address tenant application 678
ipv6 dhcp relay address tenant external-l2 679
ipv6 dhcp relay address tenant external-l3 680
ipv6 distribute-list eigrp 681
ipv6 flow 683
ipv6 hello-interval 687
ipv6 hold-interval 689
ipv6 link-local 691
ipv6 nd hop-limit 693
ipv6 nd managed-config-flag 696
ipv6 nd mtu 698
ipv6 nd ns-interval 701
ipv6 nd ns-retries 704
ipv6 nd other-config-flag 707
ipv6 nd policy 709
ipv6 nd prefix 710
ipv6 nd ra-interval 712
ipv6 nd ra-lifetime 715
ipv6 nd reachable-time 718
ipv6 nd retrans-timer 721
ipv6 nd suppress-ra-mtu 724
ipv6 nd suppress-ra 726
ipv6 next-hop-self 728
ipv6 ospf bfd 730
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xvii
Contents
ipv6 ospf cost 732
ipv6 ospf dead-interval 734
ipv6 ospf hello-interval 736
ipv6 ospf inherit 738
ipv6 ospf mtu-ignore 740
ipv6 ospf network 741
ipv6 ospf passive-interface 743
ipv6 ospf prefix-suppression 744
ipv6 ospf priority 746
ipv6 ospf retransmit-interval 748
ipv6 ospf transmit-delay 750
ipv6 passive-interface 752
ipv6 router eigrp 754
ipv6 router ospf default 756
ipv6 shared address consumer 758
ipv6 shared address provider 759
ipv6 split-horizon 760
ipv6 summary-address eigrp 762
ipv6 throughput-delay 764
isis 766
isolation 767
C H A P T E R 1 1 K Commands 769
key 770
C H A P T E R 1 2 L Commands 771
l2-unknown-unicast 774
l2protocol-tunnel 775
l3-unknown-multicast 776
l3out 777
l4l7-cluster 778
l4l7-peer 779
l4l7 780
l4l7 cluster import-from 781
l4l7 cluster name 782
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xviii
Contents
l4l7 graph 783
l4l7 resource-pool 784
label 785
label match 786
label name 787
lacp fast-select-hot-standby 788
lacp graceful-convergence 789
lacp load-defer 790
lacp max-links 791
lacp min-links 793
lacp port-priority 795
lacp port-priority interface 797
lacp rate 798
lacp rate fast normal interface 800
lacp suspend-individual 801
lacp symmetric-hash 802
last-name 803
latency 804
layer2-switched flow 805
ldap-server attribute 809
ldap-server basedn 810
ldap-server filter 811
ldap-server host 812
ldap-server retries 813
ldap-server timeout 814
leaf-group 815
leaf-interface-group 816
leaf-interface-profile 817
leaf-policy-group 819
leaf-profile 820
leaf 821
legacy 823
link 824
lldp 828
lldp holdtime 832
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xix
Contents
lldp reinit 833
lldp timer 834
load-balance 835
local-as 837
locality 839
logfile 840
logging 841
logging audit 842
logging description 843
logging event 844
logging fault 845
logging server-group 846
logging session 847
logging severity 848
logit 850
logit severity dest-grp server node 851
lsp-fast-flood 852
lsp-gen-interval 853
lsp-mtu 854
C H A P T E R 1 3 MCommands 855
mac-address 858
mac-changes 861
mac-learning 862
managed-config-check 863
managed-config-flag 864
match-precedence 865
match 866
match arp 868
match bridge-domain 869
match dscp 870
match icmp 871
match ip 872
match ip multicast group 873
match ip multicast group rp 874
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xx
Contents
match ip multicast group rp source 875
match ip multicast group source 876
match ip multicast group source rp 877
match ip multicast rp 878
match ip multicast rp group 879
match ip multicast rp group source 880
match ip multicast rp source 881
match ip multicast rp source group 882
match ip multicast source 883
match ip multicast source group 884
match ip multicast source group rp 885
match ip multicast source rp 886
match ip multicast source rp group 887
match ipv6 888
match prefix-list 889
match raw 890
match route group 891
match tcp 892
match udp 893
max-lsa 894
max-validity-period 896
max concurrent 897
max running 898
maxas-limit 899
maximum-hop-limit 900
maximum-paths 901
maximum-prefix 904
maximum-router-preference 906
mcp 907
mcp action 910
mcp control pdu-per-vlan 911
mcp description 912
mcp enable 913
mcp factor 914
mcp init-delay 915
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xxi
Contents
mcp transmit-frequency 916
member 917
message-level 918
message-size 919
metric 920
mgmt-connectivity-pref 922
mgmt-epg 923
microsoft-domain 924
microsoft 926
min-rx 927
min-tx 929
min 931
minimum-hop-limit 932
mode 933
modulus 934
monitor 935
monitor access 936
monitor fabric 937
monitor tenant 938
monitor virtual 939
mtu-ignore 940
mtu 941
multi-destination 945
multi-site-mac-address 946
multicast-address 947
multiplier 948
C H A P T E R 1 4 N Commands 951
name-alias 952
name-lookup 956
name 957
negotiate 958
neighbor-discovery 961
neighbor 962
network 964
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xxii
Contents
next-hop-self 965
node-control 966
npv 967
npv auto-load-balance 968
npv traffic-map external-interface vfc-po 969
npv traffic-map external-interface vfc 971
npv traffic-map server-interface vfc-po 972
npv traffic-map server-interface vfc 974
ntp 976
C H A P T E R 1 5 O Commands 977
oob-mgmt 978
oob-mgmt epg 979
optimize 980
option 981
org-name 982
org-unit-name 983
other-config-check 984
other-config-flag 985
C H A P T E R 1 6 P Commands 987
passive-interface 989
passphrase 990
passwd 991
password 992
password change-count 994
password change-during-interval 995
password change-interval 996
password change-password 997
password history-count 998
password no-change-interval 999
password pwd-rules 1000
password pwd-strength-check 1001
path 1002
pause 1003
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xxiii
Contents
peer-dead-interval 1004
periodic-inventory notification 1005
phone-contact 1006
phone 1007
pod-profile 1008
pod 1009
pods 1010
policy-group 1011
policy-map type control-plane-if 1013
policy-map type control-plane-leaf 1014
policy-map type control-plane-spine 1015
policy-map type data-plane 1016
policy-map type port-authentication 1017
policy-map type qos 1018
port-authentication 1019
port-authentication fail-auth-epg 1020
port-authentication fail-auth-vlan 1022
port-authentication radius-provider-group 1023
port 1024
porttrack delay 1027
porttrack minlinks 1028
porttrack state 1029
power 1030
preempt 1031
preempt delay 1032
prefix-suppression 1034
preview 1035
priority-flow-control 1036
priority 1039
priv-type 1042
priv 1043
private-as-control 1044
profile-type 1045
protocol 1047
protocol bps 1048
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xxiv
Contents
provider 1049
proxy-arp 1050
ptp 1051
pwd-lifetime 1052
C H A P T E R 1 7 Q Commands 1053
qinq-static-endpoint 1054
qos 1058
qos parameters 1059
qos preserve 1060
query-profile 1061
query 1062
queue control 1063
queue limit 1064
quota 1065
C H A P T E R 1 8 R Commands 1067
radius-provider-group 1069
radius-server host 1070
radius-server retries 1071
radius-server timeout 1072
rbac role 1073
rbac rule 1074
rbac security-domain 1075
realm 1076
record 1077
recurring 1078
redir-dest 1079
redirect 1080
redistrib-metric 1081
redistribute 1082
redundancy-mode 1083
region 1084
reload controller 1085
reload switch 1086
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xxv
Contents
remote-as 1087
remote 1088
replace-controller replace 1090
replace-controller reset 1091
request-status-count 1092
reset-to-factory 1093
response-incl 1094
response-subtree 1095
retransmit-interval 1096
retries 1097
reverse-port 1098
revision 1099
role 1100
route-control 1101
route-map 1102
route-profile 1105
route-reflector 1106
route-target 1107
router-advertisement-guard-admin-status 1109
router-advertisement-guard 1110
router-advertisement 1111
router-id 1112
router bgp 1114
router eigrp 1115
router ospf 1116
rtr-cfg 1117
run-mode 1118
C H A P T E R 1 9 S Commands 1119
sampling-rate 1146
scale-profile 1147
schedule 1148
scheduler 1149
scheduling 1150
scope 1151
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xxvi
Contents
scvmm 1153
second-file 1154
security-domain 1155
security-policy 1156
security 1157
security allow-promiscuous 1158
security forged-transmits 1159
security mac-changes 1160
send-community 1161
server 1162
service-policy 1165
service-policy type data-plane 1170
service-policy type qos 1171
service 1172
session-record-flags 1173
set 1174
set addcommunity 1177
set as-path prepend-last-as 1182
set as-path prepend 1186
set burst 1190
set cir 1191
set community 1192
set conform-cos-transmit 1199
set conform-dscp-transmit 1200
set conform 1201
set dampening 1202
set dscp-code 1207
set dscp 1208
set exceed-cos-transmit 1209
set exceed-dscp-transmit 1210
set exceed 1211
set excessive-burst 1212
set local-preference 1213
set metric-type 1217
set metric 1221
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xxvii
Contents
set mode 1225
set next-hop 1226
set pir 1230
set qos-class 1231
set tag 1233
set target-dscp 1237
set type 1238
set violate-cos-transmit 1239
set violate-dscp-transmit 1240
set violate 1241
set weight 1242
shellinabox 1246
show aaa authentication 1247
show aaa groups 1248
show access-list 1249
show accounting log 1250
show acllog deny l2 flow 1251
show acllog deny l2 flow tenant vrf 1252
show acllog deny l2 flow tenant vrf detail 1253
show acllog deny l2 pkt 1254
show acllog deny l2 pkt tenant vrf 1255
show acllog deny l2 pkt tenant vrf detail 1256
show acllog deny l3 flow 1257
show acllog deny l3 flow tenant vrf 1258
show acllog deny l3 flow tenant vrf detail 1259
show acllog deny l3 pkt 1260
show acllog deny l3 pkt tenant vrf 1261
show acllog deny l3 pkt tenant vrf detail 1262
show acllog permit l2 flow tenant vrf 1264
show acllog permit l2 flow tenant vrf detail 1265
show acllog permit l2 pkt tenant vrf 1266
show acllog permit l2 pkt tenant vrf detail 1267
show acllog permit l3 flow tenant vrf 1268
show acllog permit l3 flow tenant vrf detail 1269
show acllog permit l3 pkt tenant vrf 1270
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xxviii
Contents
show acllog permit l3 pkt tenant vrf detail 1271
show analytics 1273
show application 1274
show audits 1275
show audits tenant 1276
show audits tenant application 1277
show audits tenant application epg 1278
show audits tenant bridge-domain 1279
show audits tenant bridge-domain detail 1280
show audits tenant bridge-domain first-hop-security binding-table 1281
show audits tenant bridge-domain first-hop-security statistics arp 1282
show audits tenant bridge-domain first-hop-security statistics dhcpv4 1283
show audits tenant bridge-domain first-hop-security statistics dhcpv6 1284
show audits tenant bridge-domain first-hop-security statistics neighbor-discovery 1285
show audits tenant dnsservergroup 1286
show audits tenant dnsservergroup server 1287
show audits tenant dnsservergroup server domain 1288
show audits tenant interface bridge-domain 1289
show audits tenant interface bridge-domain detail 1290
show audits tenant interface bridge-domain first-hop-security binding-table 1291
show audits tenant interface bridge-domain first-hop-security statistics arp 1292
show audits tenant interface bridge-domain first-hop-security statistics dhcpv4 1293
show audits tenant interface bridge-domain first-hop-security statistics dhcpv6 1294
show audits tenant interface bridge-domain first-hop-security statistics neighbor-discovery 1295
show audits tenant multicast-route-maps 1296
show audits tenant vrf 1297
show audits tenant vrf acllog l2 1298
show audits tenant vrf acllog l3 1299
show audits tenant vrf detail 1301
show audits tenant vrf external-l3 bgp 1302
show audits tenant vrf external-l3 bgp node 1303
show audits tenant vrf external-l3 eigrp 1304
show audits tenant vrf external-l3 eigrp detail 1305
show audits tenant vrf external-l3 epg 1306
show audits tenant vrf external-l3 epg detail 1307
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xxix
Contents
show audits tenant vrf external-l3 epg name 1308
show audits tenant vrf external-l3 epg name detail 1309
show audits tenant vrf external-l3 interfaces 1310
show audits tenant vrf external-l3 interfaces detail 1311
show audits tenant vrf external-l3 ospf 1312
show audits tenant vrf external-l3 ospf detail 1313
show audits tenant vrf external-l3 static-route 1314
show audits tenant vrf external-l3 static-route detail 1315
show audits tenant vrf external-l3 static-route node 1316
show audits tenant vrf external-l3 static-route node detail 1317
show audits tenant vrf multicast 1318
show bridge-domain 1319
show bridge-domain detail 1320
show bridge-domain first-hop-security binding-table 1321
show bridge-domain first-hop-security statistics arp 1322
show bridge-domain first-hop-security statistics dhcpv4 1323
show bridge-domain first-hop-security statistics dhcpv6 1324
show bridge-domain first-hop-security statistics neighbor-discovery 1325
show callhome 1326
show callhome common destination-profile 1327
show callhome common query-profile 1328
show callhome common transport-email 1329
show catalog 1330
show cli command 1331
show cli internal audit 1332
show cli internal transaction 1333
show cli internal usage 1334
show cli list 1335
show cli manpage 1336
show cli path 1337
show clock 1338
show communication ciphers 1339
show communication controller 1340
show communication http 1341
show communication https 1342
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xxx
Contents
show communication shellinabox 1343
show communication ssh-service 1344
show communication telnet 1345
show communication web-requests 1346
show contract-type 1347
show contract 1348
show controller 1349
show controller detail 1350
show cores 1351
show cores status 1352
show debug counter 1353
show debug log 1354
show deployment endpoint node 1355
show dns-address 1356
show dns-domain 1357
show dot1q-tunnel 1358
show endpoints 1359
show endpoints leaf interface ethernet 1360
show endpoints leaf interface port-channel 1361
show endpoints vpc 1362
show epg 1363
show epg detail 1364
show events 1365
show events controller 1366
show events controller detail 1367
show events leaf 1368
show events leaf fex 1369
show events leaf fex module 1370
show events leaf interface ethernet 1371
show events leaf interface l3instance 1372
show events leaf interface mgmt 1373
show events leaf interface portchannel 1374
show events leaf interface tunnel 1375
show events leaf inventory chassis 1376
show events leaf inventory fans 1377
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xxxi
Contents
show events leaf inventory module 1378
show events leaf inventory module fabricport 1379
show events leaf inventory module leafport 1380
show events leaf inventory powersupply 1381
show events leaf inventory supervisor 1382
show events leaf protocol 1383
show events leaf vpc 1384
show events leaf vrf 1385
show events spine 1386
show events spine interface ethernet 1387
show events spine interface l3instance 1388
show events spine interface mgmt 1389
show events spine interface tunnel 1390
show events spine inventory chassis 1391
show events spine inventory fabric 1392
show events spine inventory fans 1393
show events spine inventory module 1394
show events spine inventory module fabricport 1395
show events spine inventory powersupply 1396
show events spine inventory supervisor 1397
show events spine inventory system 1398
show events spine protocol 1399
show events spine vrf 1400
show events tenant 1401
show events tenant application 1402
show events tenant application epg 1403
show events tenant bridge-domain 1404
show events tenant bridge-domain detail 1405
show events tenant bridge-domain first-hop-security binding-table 1406
show events tenant bridge-domain first-hop-security statistics arp 1407
show events tenant bridge-domain first-hop-security statistics dhcpv4 1408
show events tenant bridge-domain first-hop-security statistics dhcpv6 1409
show events tenant bridge-domain first-hop-security statistics neighbor-discovery 1410
show events tenant dnsservergroup 1411
show events tenant dnsservergroup server 1412
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xxxii
Contents
show events tenant dnsservergroup server domain 1413
show events tenant endpoints 1414
show events tenant endpoints leaf interface ethernet 1415
show events tenant endpoints leaf interface port-channel 1416
show events tenant endpoints vpc 1417
show events tenant interface bridge-domain 1419
show events tenant interface bridge-domain detail 1420
show events tenant interface bridge-domain first-hop-security binding-table 1421
show events tenant interface bridge-domain first-hop-security statistics arp 1422
show events tenant interface bridge-domain first-hop-security statistics dhcpv4 1423
show events tenant interface bridge-domain first-hop-security statistics dhcpv6 1424
show events tenant interface bridge-domain first-hop-security statistics neighbor-discovery 1425
show events tenant multicast-route-maps 1426
show events tenant vrf 1427
show events tenant vrf acllog l2 1428
show events tenant vrf acllog l3 1429
show events tenant vrf detail 1431
show events tenant vrf external-l3 bgp 1432
show events tenant vrf external-l3 bgp node 1433
show events tenant vrf external-l3 eigrp 1434
show events tenant vrf external-l3 eigrp detail 1435
show events tenant vrf external-l3 epg 1436
show events tenant vrf external-l3 epg detail 1437
show events tenant vrf external-l3 epg name 1438
show events tenant vrf external-l3 epg name detail 1439
show events tenant vrf external-l3 interfaces 1440
show events tenant vrf external-l3 interfaces detail 1441
show events tenant vrf external-l3 ospf 1442
show events tenant vrf external-l3 ospf detail 1443
show events tenant vrf external-l3 route-map 1444
show events tenant vrf external-l3 route-map detail 1445
show events tenant vrf external-l3 static-route 1446
show events tenant vrf external-l3 static-route detail 1447
show events tenant vrf external-l3 static-route node 1448
show events tenant vrf external-l3 static-route node detail 1449
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xxxiii
Contents
show events tenant vrf multicast 1450
show external-l2 epg 1451
show external-l2 epg name 1452
show external-l2 epg tenant 1453
show external-l3 bgp 1454
show external-l3 bgp tenant 1455
show external-l3 bgp tenant vrf 1456
show external-l3 bgp tenant vrf node 1457
show external-l3 eigrp 1458
show external-l3 eigrp detail 1459
show external-l3 eigrp node 1460
show external-l3 eigrp node detail 1461
show external-l3 eigrp tenant 1462
show external-l3 eigrp tenant detail 1463
show external-l3 eigrp tenant vrf 1464
show external-l3 eigrp tenant vrf detail 1465
show external-l3 eigrp tenant vrf node 1466
show external-l3 eigrp tenant vrf node detail 1467
show external-l3 epg 1468
show external-l3 epg detail 1469
show external-l3 epg name 1470
show external-l3 epg name detail 1471
show external-l3 epg tenant 1472
show external-l3 epg tenant detail 1473
show external-l3 epg tenant vrf 1474
show external-l3 epg tenant vrf detail 1475
show external-l3 interfaces 1476
show external-l3 interfaces detail 1477
show external-l3 interfaces node 1478
show external-l3 interfaces node detail 1479
show external-l3 interfaces tenant 1480
show external-l3 interfaces tenant detail 1481
show external-l3 interfaces tenant vrf 1482
show external-l3 interfaces tenant vrf detail 1483
show external-l3 interfaces tenant vrf node 1484
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xxxiv
Contents
show external-l3 interfaces tenant vrf node detail 1485
show external-l3 ospf 1486
show external-l3 ospf detail 1487
show external-l3 ospf node 1488
show external-l3 ospf node detail 1489
show external-l3 ospf tenant 1490
show external-l3 ospf tenant detail 1491
show external-l3 ospf tenant vrf 1492
show external-l3 ospf tenant vrf detail 1493
show external-l3 ospf tenant vrf node 1494
show external-l3 ospf tenant vrf node detail 1495
show external-l3 route-map 1496
show external-l3 route-map detail 1497
show external-l3 route-map name 1498
show external-l3 route-map name detail 1499
show external-l3 route-map tenant 1500
show external-l3 route-map tenant detail 1501
show external-l3 route-map tenant vrf 1502
show external-l3 route-map tenant vrf detail 1503
show external-l3 route-map tenant vrf node 1504
show external-l3 route-map tenant vrf node detail 1505
show external-l3 static-route 1506
show external-l3 static-route detail 1507
show external-l3 static-route node 1508
show external-l3 static-route node detail 1509
show external-l3 static-route tenant 1510
show external-l3 static-route tenant detail 1511
show external-l3 static-route tenant vrf 1512
show external-l3 static-route tenant vrf detail 1513
show external-l3 static-route tenant vrf node 1514
show external-l3 static-route tenant vrf node detail 1515
show fabric-recovery status 1516
show faults 1517
show faults controller 1519
show faults controller detail 1520
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xxxv
Contents
show faults l4l7-cluster 1521
show faults l4l7-graph 1522
show faults leaf 1523
show faults leaf fex 1524
show faults leaf fex module 1525
show faults leaf interface ethernet 1526
show faults leaf interface l3instance 1527
show faults leaf interface mgmt 1528
show faults leaf interface portchannel 1529
show faults leaf interface tunnel 1530
show faults leaf inventory chassis 1531
show faults leaf inventory fans 1532
show faults leaf inventory module 1533
show faults leaf inventory module fabricport 1534
show faults leaf inventory module leafport 1535
show faults leaf inventory powersupply 1536
show faults leaf inventory supervisor 1537
show faults leaf protocol 1538
show faults leaf vpc 1539
show faults leaf vrf 1540
show faults microsoft domain 1541
show faults microsoft domain name 1542
show faults microsoft domain name hyperv 1543
show faults microsoft domain name port-group 1544
show faults microsoft domain name scvmm 1545
show faults microsoft domain name vm 1546
show faults microsoft domain name vm name 1547
show faults quota 1548
show faults spine 1549
show faults spine interface ethernet 1550
show faults spine interface l3instance 1551
show faults spine interface mgmt 1552
show faults spine interface tunnel 1553
show faults spine inventory chassis 1554
show faults spine inventory fabric 1555
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xxxvi
Contents
show faults spine inventory fans 1556
show faults spine inventory module 1557
show faults spine inventory module fabricport 1558
show faults spine inventory powersupply 1559
show faults spine inventory supervisor 1560
show faults spine inventory system 1561
show faults spine protocol 1562
show faults spine vrf 1563
show faults tenant 1564
show faults tenant application 1565
show faults tenant application epg 1566
show faults tenant bridge-domain 1567
show faults tenant bridge-domain detail 1568
show faults tenant bridge-domain first-hop-security binding-table 1569
show faults tenant bridge-domain first-hop-security statistics arp 1570
show faults tenant bridge-domain first-hop-security statistics dhcpv4 1571
show faults tenant bridge-domain first-hop-security statistics dhcpv6 1572
show faults tenant bridge-domain first-hop-security statistics neighbor-discovery 1573
show faults tenant dnsservergroup 1574
show faults tenant dnsservergroup server 1575
show faults tenant dnsservergroup server domain 1576
show faults tenant interface bridge-domain 1577
show faults tenant interface bridge-domain detail 1578
show faults tenant interface bridge-domain first-hop-security binding-table 1579
show faults tenant interface bridge-domain first-hop-security statistics arp 1580
show faults tenant interface bridge-domain first-hop-security statistics dhcpv4 1581
show faults tenant interface bridge-domain first-hop-security statistics dhcpv6 1582
show faults tenant interface bridge-domain first-hop-security statistics neighbor-discovery 1583
show faults tenant multicast-route-maps 1584
show faults tenant vrf 1585
show faults tenant vrf acllog l2 1586
show faults tenant vrf acllog l3 1587
show faults tenant vrf detail 1589
show faults tenant vrf external-l3 bgp 1590
show faults tenant vrf external-l3 bgp node 1591
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xxxvii
Contents
show faults tenant vrf external-l3 eigrp 1592
show faults tenant vrf external-l3 eigrp detail 1593
show faults tenant vrf external-l3 epg 1594
show faults tenant vrf external-l3 epg detail 1595
show faults tenant vrf external-l3 epg name 1596
show faults tenant vrf external-l3 epg name detail 1597
show faults tenant vrf external-l3 interfaces 1598
show faults tenant vrf external-l3 interfaces detail 1599
show faults tenant vrf external-l3 ospf 1600
show faults tenant vrf external-l3 ospf detail 1601
show faults tenant vrf external-l3 static-route 1602
show faults tenant vrf external-l3 static-route detail 1603
show faults tenant vrf external-l3 static-route node 1604
show faults tenant vrf external-l3 static-route node detail 1605
show faults tenant vrf multicast 1606
show faults vmware domain 1607
show faults vmware domain name 1608
show faults vmware domain name epg 1609
show faults vmware domain name esx 1610
show faults vmware domain name port-group 1611
show faults vmware domain name trunk-portgroup 1612
show faults vmware domain name vcenter 1613
show faults vmware domain name vm 1614
show faults vmware domain name vm name 1615
show fips 1616
show fips status 1617
show firmware repository 1618
show firmware repository detail 1619
show firmware upgrade status 1620
show firmware upgrade status controller-group 1621
show firmware upgrade status controller-group detail 1622
show firmware upgrade status detail 1623
show firmware upgrade status switch-group 1624
show firmware upgrade status switch-group detail 1625
show flow exporter 1626
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xxxviii
Contents
show flow exporter infra 1627
show flow exporter tenant 1628
show flow monitor 1629
show flow monitor infra 1630
show flow monitor tenant 1631
show flow node-policy 1632
show flow node-policy detail 1633
show flow record 1634
show flow record infra 1635
show flow record tenant 1636
show flow vm-exporter 1637
show health 1638
show health leaf 1639
show health leaf fex 1640
show health leaf fex module 1641
show health leaf interface ethernet 1642
show health leaf interface l3instance 1643
show health leaf interface mgmt 1644
show health leaf interface portchannel 1645
show health leaf interface tunnel 1646
show health leaf inventory chassis 1647
show health leaf inventory fans 1648
show health leaf inventory module 1649
show health leaf inventory module fabricport 1650
show health leaf inventory module leafport 1651
show health leaf inventory powersupply 1652
show health leaf inventory supervisor 1653
show health leaf protocol 1654
show health leaf vpc 1655
show health leaf vrf 1656
show health spine 1657
show health spine interface ethernet 1658
show health spine interface l3instance 1659
show health spine interface mgmt 1660
show health spine interface tunnel 1661
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xxxix
Contents
show health spine inventory chassis 1662
show health spine inventory fabric 1663
show health spine inventory fans 1664
show health spine inventory module 1665
show health spine inventory module fabricport 1666
show health spine inventory powersupply 1667
show health spine inventory supervisor 1668
show health spine inventory system 1669
show health spine protocol 1670
show health spine vrf 1671
show health tenant 1672
show health tenant application 1673
show health tenant application epg 1674
show health tenant bridge-domain 1675
show health tenant bridge-domain detail 1676
show health tenant bridge-domain first-hop-security binding-table 1677
show health tenant bridge-domain first-hop-security statistics arp 1678
show health tenant bridge-domain first-hop-security statistics dhcpv4 1679
show health tenant bridge-domain first-hop-security statistics dhcpv6 1680
show health tenant bridge-domain first-hop-security statistics neighbor-discovery 1681
show health tenant dnsservergroup 1682
show health tenant dnsservergroup server 1683
show health tenant dnsservergroup server domain 1684
show health tenant interface bridge-domain 1685
show health tenant interface bridge-domain detail 1686
show health tenant interface bridge-domain first-hop-security binding-table 1687
show health tenant interface bridge-domain first-hop-security statistics arp 1688
show health tenant interface bridge-domain first-hop-security statistics dhcpv4 1689
show health tenant interface bridge-domain first-hop-security statistics dhcpv6 1690
show health tenant interface bridge-domain first-hop-security statistics
neighbor-discovery 1691
show health tenant multicast-route-maps 1692
show health tenant vrf 1693
show health tenant vrf acllog l2 1694
show health tenant vrf acllog l3 1695
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xl
Contents
show health tenant vrf detail 1697
show health tenant vrf external-l3 bgp 1698
show health tenant vrf external-l3 bgp node 1699
show health tenant vrf external-l3 eigrp 1700
show health tenant vrf external-l3 eigrp detail 1701
show health tenant vrf external-l3 epg 1702
show health tenant vrf external-l3 epg detail 1703
show health tenant vrf external-l3 epg name 1704
show health tenant vrf external-l3 epg name detail 1705
show health tenant vrf external-l3 interfaces 1706
show health tenant vrf external-l3 interfaces detail 1707
show health tenant vrf external-l3 ospf 1708
show health tenant vrf external-l3 ospf detail 1709
show health tenant vrf external-l3 static-route 1710
show health tenant vrf external-l3 static-route detail 1711
show health tenant vrf external-l3 static-route node 1712
show health tenant vrf external-l3 static-route node detail 1713
show health tenant vrf multicast 1714
show inband-mgmt 1715
show inband-mgmt controller 1716
show inband-mgmt switch 1717
show interface bridge-domain 1718
show interface bridge-domain detail 1719
show interface bridge-domain first-hop-security binding-table 1720
show interface bridge-domain first-hop-security statistics arp 1721
show interface bridge-domain first-hop-security statistics dhcpv4 1722
show interface bridge-domain first-hop-security statistics dhcpv6 1723
show interface bridge-domain first-hop-security statistics neighbor-discovery 1724
show ip interface bridge-domain 1725
show ipv6 interface bridge-domain 1726
show l4l7-cluster 1727
show l4l7-graph 1728
show l4l7-package 1729
show ldap-server 1730
show locator-led 1731
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xli
Contents
show locator-led status leaf 1732
show microsoft domain 1733
show microsoft domain name 1734
show microsoft domain name hyperv 1735
show microsoft domain name port-group 1736
show microsoft domain name scvmm 1737
show microsoft domain name vm 1738
show microsoft domain name vm name 1739
show microsoft vm 1740
show monitor access 1741
show monitor fabric 1742
show monitor summary 1743
show monitor tenant 1744
show monitor virtual 1745
show name-alias tenant 1746
show name-alias tenant acl 1747
show name-alias tenant application 1748
show name-alias tenant application epg 1749
show name-alias tenant bridge-domain 1750
show name-alias tenant contract 1751
show name-alias tenant contract subject 1752
show name-alias tenant l3out 1753
show name-alias tenant vrf 1754
show ntpq 1755
show oob-mgmt 1756
show oob-mgmt controller 1757
show oob-mgmt switch 1758
show pd-recovery status 1759
show policy-map 1760
show policy-map type data-plane 1761
show policy-map type qos 1762
show port-channel leaf 1763
show port-channel map 1764
show port-channel map leaf 1765
show pwd-rules 1766
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xlii
Contents
show quota 1767
show radius-server 1768
show resource 1769
show resource conflict encap-vlan epg 1770
show resource conflict encap-vlan epg node 1771
show role 1772
show running-config 1773
show sessions 1774
show sessions controller 1775
show sessions controller detail 1776
show sessions leaf 1777
show sessions spine 1778
show snapshot active 1779
show snapshot files 1780
show snapshot jobs 1781
show snmp 1782
show snmp clientgroups 1783
show snmp community 1784
show snmp engineid 1785
show snmp hosts 1786
show snmp summary 1787
show snmp users 1788
show stats 1789
show stats granularity communication controller 1790
show stats granularity leaf 1791
show stats granularity leaf fex 1792
show stats granularity leaf fex module 1793
show stats granularity leaf interface ethernet 1794
show stats granularity leaf interface mgmt 1795
show stats granularity leaf interface portchannel 1796
show stats granularity leaf inventory chassis 1797
show stats granularity leaf inventory fans 1798
show stats granularity leaf inventory powersupply 1799
show stats granularity leaf inventory supervisor 1800
show stats granularity spine 1801
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xliii
Contents
show stats granularity spine interface ethernet 1802
show stats granularity spine interface mgmt 1803
show stats granularity spine inventory chassis 1804
show stats granularity spine inventory fabric 1805
show stats granularity spine inventory fans 1806
show stats granularity spine inventory module 1807
show stats granularity spine inventory powersupply 1808
show stats granularity spine inventory supervisor 1809
show stats granularity spine inventory system 1810
show stats granularity tenant 1811
show stats granularity tenant application 1812
show stats granularity tenant application epg 1813
show stats granularity tenant dnsservergroup 1814
show stats granularity tenant dnsservergroup server 1815
show stats granularity tenant dnsservergroup server domain 1816
show stats granularity tenant dot1q-tunnel 1817
show stats granularity tenant multicast-route-maps 1818
show stats granularity tenant vrf 1819
show stats granularity tenant vrf acllog l2 1820
show stats granularity tenant vrf acllog l3 1821
show stats granularity tenant vrf detail 1822
show stats granularity tenant vrf external-l3 bgp 1823
show stats granularity tenant vrf external-l3 bgp node 1824
show stats granularity tenant vrf external-l3 eigrp 1825
show stats granularity tenant vrf external-l3 eigrp detail 1826
show stats granularity tenant vrf external-l3 epg 1827
show stats granularity tenant vrf external-l3 epg detail 1828
show stats granularity tenant vrf external-l3 epg name 1829
show stats granularity tenant vrf external-l3 epg name detail 1830
show stats granularity tenant vrf external-l3 interfaces 1831
show stats granularity tenant vrf external-l3 interfaces detail 1832
show stats granularity tenant vrf external-l3 ospf 1833
show stats granularity tenant vrf external-l3 ospf detail 1834
show stats granularity tenant vrf external-l3 static-route 1835
show stats granularity tenant vrf external-l3 static-route detail 1836
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xliv
Contents
show stats granularity tenant vrf external-l3 static-route node 1837
show stats granularity tenant vrf external-l3 static-route node detail 1838
show stats granularity tenant vrf multicast 1839
show switch 1840
show switch detail 1841
show tacacs-server 1842
show techsupport all 1843
show techsupport controllers 1844
show techsupport host 1845
show techsupport switch 1846
show tenant 1847
show tenant access-list 1848
show tenant application 1849
show tenant application endpoints 1850
show tenant application endpoints leaf interface ethernet 1851
show tenant application endpoints leaf interface port-channel 1852
show tenant application endpoints vpc 1853
show tenant application epg 1854
show tenant application epg detail 1855
show tenant application epg endpoints 1856
show tenant application epg endpoints leaf interface ethernet 1857
show tenant application epg endpoints leaf interface port-channel 1858
show tenant application epg endpoints vpc 1859
show tenant bridge-domain 1861
show tenant bridge-domain detail 1862
show tenant bridge-domain first-hop-security binding-table 1863
show tenant bridge-domain first-hop-security statistics arp 1864
show tenant bridge-domain first-hop-security statistics dhcpv4 1865
show tenant bridge-domain first-hop-security statistics dhcpv6 1866
show tenant bridge-domain first-hop-security statistics neighbor-discovery 1867
show tenant contract-type 1868
show tenant contract 1869
show tenant detail 1870
show tenant dnsservergroup 1871
show tenant dnsservergroup server 1872
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xlv
Contents
show tenant dnsservergroup server domain 1873
show tenant dot1q-tunnel 1874
show tenant endpoints 1875
show tenant endpoints leaf interface ethernet 1876
show tenant endpoints leaf interface port-channel 1877
show tenant endpoints vpc 1878
show tenant epg 1879
show tenant epg detail 1880
show tenant external-l2 epg 1881
show tenant interface bridge-domain 1882
show tenant interface bridge-domain detail 1883
show tenant interface bridge-domain first-hop-security binding-table 1884
show tenant interface bridge-domain first-hop-security statistics arp 1885
show tenant interface bridge-domain first-hop-security statistics dhcpv4 1886
show tenant interface bridge-domain first-hop-security statistics dhcpv6 1887
show tenant interface bridge-domain first-hop-security statistics neighbor-discovery 1888
show tenant ip interface bridge-domain 1889
show tenant ipv6 interface bridge-domain 1890
show tenant multicast-route-maps 1891
show tenant policy-map 1892
show tenant policy-map type data-plane 1893
show tenant policy-map type qos 1894
show tenant vrf 1895
show tenant vrf acllog l2 1896
show tenant vrf acllog l3 1897
show tenant vrf detail 1898
show tenant vrf external-l3 bgp 1899
show tenant vrf external-l3 bgp node 1900
show tenant vrf external-l3 eigrp 1901
show tenant vrf external-l3 eigrp detail 1902
show tenant vrf external-l3 epg 1903
show tenant vrf external-l3 epg detail 1904
show tenant vrf external-l3 epg name 1905
show tenant vrf external-l3 epg name detail 1906
show tenant vrf external-l3 interfaces 1907
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xlvi
Contents
show tenant vrf external-l3 interfaces detail 1908
show tenant vrf external-l3 ospf 1909
show tenant vrf external-l3 ospf detail 1910
show tenant vrf external-l3 route-map 1911
show tenant vrf external-l3 route-map detail 1912
show tenant vrf external-l3 static-route 1913
show tenant vrf external-l3 static-route detail 1914
show tenant vrf external-l3 static-route node 1915
show tenant vrf external-l3 static-route node detail 1916
show tenant vrf multicast 1917
show troubleshoot epext session 1918
show troubleshoot epext session atomiccounter 1919
show troubleshoot epext session audit 1920
show troubleshoot epext session contracts 1921
show troubleshoot epext session deployments 1922
show troubleshoot epext session events 1923
show troubleshoot epext session faults 1924
show troubleshoot epext session latency 1925
show troubleshoot epext session monitor 1926
show troubleshoot epext session reports 1927
show troubleshoot epext session statistics 1928
show troubleshoot epext session topology 1929
show troubleshoot epext session traceroute 1930
show troubleshoot epext sessions 1931
show troubleshoot eptoep session 1932
show troubleshoot eptoep session atomiccounter 1933
show troubleshoot eptoep session audit 1934
show troubleshoot eptoep session contracts 1935
show troubleshoot eptoep session deployments 1936
show troubleshoot eptoep session events 1937
show troubleshoot eptoep session faults 1938
show troubleshoot eptoep session latency 1939
show troubleshoot eptoep session monitor 1940
show troubleshoot eptoep session reports 1941
show troubleshoot eptoep session statistics 1942
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xlvii
Contents
show troubleshoot eptoep session topology 1943
show troubleshoot eptoep session traceroute 1944
show troubleshoot eptoep sessions 1945
show username 1946
show username detail 1947
show version 1948
show vlan-domain 1949
show vmm internal debug 1950
show vmm internal debug epg 1951
show vmm internal debug mac 1952
show vmware domain 1953
show vmware domain name 1954
show vmware domain name epg 1955
show vmware domain name esx 1956
show vmware domain name port-group 1957
show vmware domain name trunk-portgroup 1958
show vmware domain name vcenter 1959
show vmware domain name vm 1960
show vmware domain name vm name 1961
show vmware vm 1962
show vpc 1963
show vpc map leaf 1964
show vrf 1965
show vrf detail 1966
show vsan-domain 1967
shut 1968
shutdown 1969
site-id 1973
slow-drain congestion-timeout action 1974
slow-drain congestion-timeout count 1977
slow-drain pause 1980
slow-timer 1983
snapshot download 1984
snapshot export 1985
snapshot import 1986
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)xlviii
Contents
snapshot rollback 1987
snapshot upload 1988
snmp-server clientgroup 1989
snmp-server community 1990
snmp-server contact 1991
snmp-server host 1992
snmp-server location 1993
snmp-server protocol 1994
snmp-server user 1995
source-guard-admin-status 1996
source 1997
source application 1999
source interface ethernet 2000
source interface port-channel 2001
source interface vpc 2002
spanning-tree 2003
spanning-tree bpdu-filter 2007
spanning-tree bpdu-guard 2008
speed 2009
spf-interval 2012
spine-group 2013
spine-interface-group 2014
spine-interface-policy-group 2015
spine-interface-profile 2017
spine-policy-group 2018
spine-profile 2019
spine 2020
ssh-key 2021
ssh-service 2022
ssl-protocols 2023
ssl-validation-level 2024
state 2025
static-endpoint 2026
static-tep 2030
statistics 2034
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) xlix
Contents
storm-control broadcast level 2035
storm-control broadcast pps 2038
storm-control level 2041
storm-control multicast level 2044
storm-control multicast pps 2047
storm-control pps 2050
storm-control unicast level 2053
storm-control unicast pps 2056
street-address 2059
subject 2060
subnet 2061
summary-address 2062
svcredir-pol 2063
switch-group 2064
switch 2065
switching 2066
switchport 2067
switchport access vlan tenant application 2069
switchport access vlan tenant external-svi 2073
switchport mode 2076
switchport port-authentication 2080
switchport port-authentication enable 2081
switchport port-authentication host-mode 2082
switchport port-security maximum 2083
switchport port-security timeout 2086
switchport port-security violation 2089
switchport tenant 2092
switchport trunk allowed vlan inband-mgmt 2095
switchport trunk allowed vlan tenant application 2096
switchport trunk allowed vlan tenant external-l2 2100
switchport trunk allowed vlan tenant external-svi 2103
switchport trunk allowed vlan tenant legacy-forwarding 2106
switchport trunk allowed vsan tenant application 2109
switchport trunk native vlan tenant application 2112
switchport trunk native vlan tenant external-svi 2116
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)l
Contents
switchport trunk qinq outer-vlan inner-vlan tenant application 2119
switchport vepa 2123
switchport vlan 2126
switchport vsan 2129
switchport vsan tenant application 2132
syslog 2133
system cluster-size 2134
system controller-id 2135
system dynamic-load-balance 2136
system fabric-security-mode 2137
system jumbomtu 2138
system pod 2139
system switch-id 2140
system use-infra-gipo 2141
C H A P T E R 2 0 T Commands 2143
tacacs-server host 2147
tacacs-server retries 2148
tacacs-server timeout 2149
tag 2150
target 2152
telnet 2153
template bfd 2154
template bgp address-family 2156
template bgp timers 2157
template dhcp option 2158
template dhcp relay 2159
template eigrp interface-policy 2160
template eigrp vrf-policy 2161
template endpoint retention policy 2162
template fabric-interface-policy-group 2163
template fc-fabric-policy 2164
template fc-leaf-policy 2165
template hsrp group-policy 2166
template hsrp interface-policy 2167
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) li
Contents
template ip igmp interface-policy 2168
template ip igmp snooping policy 2169
template ip pim interface-policy 2170
template ipv6 nd policy 2171
template ipv6 nd prefix 2173
template isis-fabric 2174
template leaf-policy-group 2175
template ntp-fabric 2176
template ospf interface-policy 2177
template ospf vrf-policy 2178
template pod-group 2179
template policy-group 2180
template port-channel 2181
template route-profile 2182
template route group 2184
template route tag 2185
template snmp-fabric 2186
template spine-fabric-interface-policy-group 2187
template spine-interface-policy-group 2188
template spine-policy-group 2189
template vsan-attribute 2190
tenant 2191
terminal 2192
time 2193
time start daily 2194
time start weekly 2195
timeout 2196
timers 2197
timers lsa-arrival 2201
timers lsa-group-pacing 2202
timers throttle lsa 2203
timers throttle spf 2205
totp-enable 2207
tp 2208
transmit-delay 2209
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)lii
Contents
transport 2210
transport email from 2212
transport email mail-server 2213
transport email reply-to 2214
trigger fabric-recovery 2215
trigger shutdown 2216
trigger snapshot download 2217
trigger snapshot export 2218
trigger snapshot import 2219
trigger snapshot rollback 2220
trigger snapshot upload 2221
trigger techsupport all 2222
trigger techsupport controllers 2223
trigger techsupport host 2224
trigger techsupport local 2225
trigger techsupport switch 2226
trigger troubleshoot epext session report 2227
trigger troubleshoot eptoep session report 2228
trigger vmware 2229
troubleshoot epext session atomiccounter 2230
troubleshoot epext session description 2231
troubleshoot epext session latency 2232
troubleshoot epext session latestminutes 2233
troubleshoot epext session monitor destination apic 2234
troubleshoot epext session monitor destination prefdestgroup 2235
troubleshoot epext session monitor destination tenant 2236
troubleshoot epext session scheduler 2238
troubleshoot epext session srcextip destip tenant application 2239
troubleshoot epext session srcextip destip tenant vrf 2240
troubleshoot epext session srcip tenant application epg destextip 2241
troubleshoot epext session srcip tenant vrf destextip 2242
troubleshoot epext session starttime 2243
troubleshoot epext session traceroute 2244
troubleshoot epext session traceroute protocol icmp 2245
troubleshoot epext session traceroute protocol tcp 2246
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) liii
Contents
troubleshoot epext session traceroute protocol udp 2247
troubleshoot eptoep session atomiccounter 2248
troubleshoot eptoep session description 2249
troubleshoot eptoep session latency 2250
troubleshoot eptoep session latestminutes 2251
troubleshoot eptoep session monitor destination apic 2252
troubleshoot eptoep session monitor destination prefdestgroup 2253
troubleshoot eptoep session monitor destination tenant 2254
troubleshoot eptoep session scheduler 2256
troubleshoot eptoep session srcip tenant application epg destip tenant application 2257
troubleshoot eptoep session srcip tenant application epg destip tenant vrf 2258
troubleshoot eptoep session srcip tenant vrf destip tenant application 2259
troubleshoot eptoep session srcip tenant vrf destip tenant vrf 2260
troubleshoot eptoep session srcmac tenant application epg destmac tenant application 2261
troubleshoot eptoep session srcmac tenant application epg destmac tenant vrf 2263
troubleshoot eptoep session srcmac tenant vrf destmac tenant application 2265
troubleshoot eptoep session srcmac tenant vrf destmac tenant vrf 2267
troubleshoot eptoep session starttime 2269
troubleshoot eptoep session traceroute 2270
troubleshoot eptoep session traceroute protocol icmp 2271
troubleshoot eptoep session traceroute protocol tcp 2272
troubleshoot eptoep session traceroute protocol udp 2273
trunk-portgroup 2274
trust-control 2275
trusted-key 2276
try 2277
C H A P T E R 2 1 U Commands 2279
ui-idle-timeout-seconds 2280
unicast 2281
update-source ethernet 2282
update-source loopback 2283
update-source vlan 2284
usage 2285
use-bia 2286
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)liv
Contents
use-keyring 2287
use-vrf 2288
user 2289
username 2290
C H A P T E R 2 2 V Commands 2291
vcenter 2293
vemcmd show avs 2294
vemcmd show cdp 2295
vemcmd show dfw connection 2296
vemcmd show dfw flows 2297
vemcmd show dfw globals 2298
vemcmd show dfw interfaces 2299
vemcmd show dfw port-drop 2300
vemcmd show dfw session 2301
vemcmd show dfwdenyflows 2302
vemcmd show dfwflows ftp 2303
vemcmd show dfwflows internal 2304
vemcmd show dfwflows ltl 2305
vemcmd show dfwslflows 2306
vemcmd show epp 2307
vemcmd show heap 2308
vemcmd show host 2309
vemcmd show l2 2310
vemcmd show lacp 2311
vemcmd show lldp 2312
vemcmd show mempool 2313
vemcmd show microsegment tables brief 2314
vemcmd show microsegment tables info 2315
vemcmd show opflex 2316
vemcmd show packets 2317
vemcmd show pc 2318
vemcmd show pd-port 2319
vemcmd show port 2320
vemcmd show portmac 2321
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) lv
Contents
vemcmd show proxy-arp 2322
vemcmd show sod 2323
vemcmd show span 2324
vemcmd show stats cookie 2325
vemcmd show useg all 2326
vemcmd show useg tables brief 2327
vemcmd show useg tables info 2328
vemcmd show useg unresolved 2329
vemcmd show version 2330
vemcmd show vlan 2331
vemsend 2332
version 2333
vlan-domain 2335
vlan-pool 2340
vlan-range 2341
vlan 2342
vmware-domain 2344
vnic 2346
vpc context 2347
vpc domain consecutive 2348
vpc domain explicit 2349
vpc domain reciprocal 2350
vrf-blacklist-mode 2351
vrf 2352
vsan-domain 2361
vsan 2364
vxlan 2365
C H A P T E R 2 3 WCommands 2367
webtoken-timeout-seconds 2368
weight 2369
where 2370
where detail 2371
whitelist-blacklist-mix 2372
winservers 2373
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)lvi
Contents
C H A P T E R 2 4 Z Commands 2375
zone 2376
zones 2377
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) lvii
Contents
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)lviii
Contents
Preface
• Audience, page lix
• Document Conventions, page lix
• Related Documentation, page lxi
• Documentation Feedback, page lxi
AudienceThis guide is intended for network and systems administrators who configure and maintain the ApplicationCentric Infrastructure fabric.
Document ConventionsCommand descriptions use the following conventions:
DescriptionConvention
Bold text indicates the commands and keywords that you enter literallyas shown.
bold
Italic text indicates arguments for which the user supplies the values.Italic
Square brackets enclose an optional element (keyword or argument).[x]
Square brackets enclosing keywords or arguments separated by a verticalbar indicate an optional choice.
[x | y]
Braces enclosing keywords or arguments separated by a vertical barindicate a required choice.
{x | y}
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) lix
DescriptionConvention
Nested set of square brackets or braces indicate optional or requiredchoices within optional or required elements. Braces and a vertical barwithin square brackets indicate a required choice within an optionalelement.
[x {y | z}]
Indicates a variable for which you supply values, in context where italicscannot be used.
variable
A nonquoted set of characters. Do not use quotation marks around thestring or the string will include the quotation marks.
string
Examples use the following conventions:
DescriptionConvention
Terminal sessions and information the switch displays are in screen font.screen font
Information you must enter is in boldface screen font.boldface screen font
Arguments for which you supply values are in italic screen font.italic screen font
Nonprinting characters, such as passwords, are in angle brackets.< >
Default responses to system prompts are in square brackets.[ ]
An exclamation point (!) or a pound sign (#) at the beginning of a lineof code indicates a comment line.
!, #
This document uses the following conventions:
Means reader take note. Notes contain helpful suggestions or references to material not covered in themanual.
Note
Means reader be careful. In this situation, you might do something that could result in equipment damageor loss of data.
Caution
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)lx
PrefaceDocument Conventions
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before youwork on any equipment, be aware of the hazards involved with electrical circuitry and be familiar withstandard practices for preventing accidents. Use the statement number provided at the end of each warningto locate its translation in the translated safety warnings that accompanied this device.
SAVE THESE INSTRUCTIONS
Warning
Related DocumentationCisco Application Centric Infrastructure (ACI) Documentation
The ACI documentation is available at the following URL: http://www.cisco.com/c/en/us/support/cloud-systems-management/application-policy-infrastructure-controller-apic/tsd-products-support-series-home.html.
Cisco Application Centric Infrastructure (ACI) Simulator Documentation
The Cisco ACI Simulator documentation is available at http://www.cisco.com/c/en/us/support/cloud-systems-management/application-centric-infrastructure-simulator/tsd-products-support-series-home.html.
Cisco Nexus 9000 Series Switches Documentation
The Cisco Nexus 9000 Series Switches documentation is available at http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/tsd-products-support-series-home.html.
Cisco Application Virtual Switch Documentation
The Cisco Application Virtual Switch (AVS) documentation is available at http://www.cisco.com/c/en/us/support/switches/application-virtual-switch/tsd-products-support-series-home.html.
Cisco Application Centric Infrastructure (ACI) Integration with OpenStack Documentation
Cisco ACI integration with OpenStack documentation is available at http://www.cisco.com/c/en/us/support/cloud-systems-management/application-policy-infrastructure-controller-apic/tsd-products-support-series-home.html.
Documentation FeedbackTo provide technical feedback on this document, or to report an error or omission, please send your commentsto [email protected]. We appreciate your feedback.
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) lxi
PrefaceRelated Documentation
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)lxii
PrefaceDocumentation Feedback
Using the APIC CLI
• Using the NX-OS Style CLI, page 1
Using the NX-OS Style CLI
The APIC NX-OS style CLI uses similar syntax and other conventions to the Cisco NX-OS CLI, but theAPIC operating system is not a version of Cisco NX-OS software. Do not assume that a Cisco NX-OSCLI command works with or has the same function on the APIC CLI.
Note
Abbreviating Commands
You can abbreviate commands and keywords by entering the first few characters of a command. Theabbreviation must include sufficient characters to make it unique from other commands or keywords. If youare having trouble entering a command, check the system prompt and enter the question mark (?) for a list ofavailable commands. You might be in the wrong command mode or using incorrect syntax. Commandabbreviation is shown in the following example:
apic1# show aaa authenticationDefault : localConsole : local
apic1# sh aa aDefault : localConsole : local
Command Completion
To complete a command or keyword after entering an abbreviated string, press the Tab key. The CLI completesthe command or keyword only if the partial string matches only one command or keyword.
Some commands, such as show hardware internal power-management, require the Tab key for partialcompletion and the ESC key for the remainder of the completion.
Note
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1
Viewing Command Options
After typing a partial command, you can display the command options by typing a question mark (?), as shownin the following example:
apic1# show aaa ?authentication Show AAA Authentication informationgroups Show AAA group information
Command History
The history buffer stores the previous commands you entered. Using the Up arrow key (or typing Ctrl-P), youcan recall commands in the history buffer, beginning with the most recent command. Repeat the key sequenceto recall successively older commands. To return to more recent commands in the history buffer after recallingcommands, use the Down arrow key or type Ctrl-N).
Filtering show Command Output
You can use the vertical bar (|) with any show command and include a filter option and filtering expression.The filtering is performed by matching each output line with a regular expression. By selecting different filteroptions you can include or exclude all output that matches the expression. You can also display all outputbeginning with the line that matches the expression.
An example of filtering options with the show command is as follows:
apic1# show aaa authenticationDefault : localConsole : local
apic1# show aaa authentication | grep ConsoleConsole : localapic1#
Displaying a List of Commands and Syntax
To display a list of CLI commands and their syntax, use the show cli list command, as shown in the followingexample
apic1# show cli list[ ][mode] [None ] exec[cfg ][mode] [exec ] configure [['terminal', 't']][cfg ][mode] [configure ] power redundancy-policy <WORD>[cfg ][cmd ] [power ] redundancy-mode combined|ps-redundant|redundant...
You can filter the output of this command, as shown in the following example:
apic1# show cli list | grep ntp[cfg ][mode] [pod ] ntp[cfg ][cmd ] [ntp ] authenticate[cfg ][cmd ] [ntp ] authentication-key <id> [md5 <md5>]...
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2
Using the APIC CLIUsing the NX-OS Style CLI
Negating a Command with the no Prefix
Almost every configuration command has a no form that can be used to disable a feature, revert to a defaultvalue, or remove a configuration.
To disable a feature, remove a created object, or revert a configuration setting to its default value, mostconfiguration commands can be preceded with the prefix 'no'.
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 3
Using the APIC CLIUsing the NX-OS Style CLI
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)4
Using the APIC CLIUsing the NX-OS Style CLI
A Commands
• aaa authentication login console, page 8
• aaa authentication login default, page 9
• aaa authentication login domain, page 10
• aaa authentication login fallback-check, page 11
• aaa authentication login ping-check, page 12
• aaa banner, page 13
• aaa group server ldap, page 14
• aaa group server radius, page 15
• aaa group server tacacsplus, page 16
• aaa user default-role, page 17
• absolute, page 18
• access-encap, page 19
• access-group, page 20
• access-list, page 21
• account-status, page 22
• action, page 23
• active-flow-timeout, page 24
• address-family, page 25
• address-pool-ref, page 29
• address-pool, page 30
• address-range, page 31
• address, page 32
• admin-state-enable, page 33
• admin, page 35
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 5
• advertise-subnet, page 36
• aggregate-address, page 37
• allow-credential, page 38
• allow-origin, page 39
• allow-promiscuous, page 40
• allow-self-as, page 41
• allow-writes, page 42
• allowed-self-as-count, page 43
• analytics, page 44
• application, page 45
• area default-cost, page 46
• area interpod, page 47
• area l3out, page 48
• area loopback, page 49
• area nssa, page 50
• area nssa default-information-originate, page 51
• area nssa no-redistribute, page 52
• area nssa translate, page 53
• area range, page 54
• area route-map, page 55
• area stub, page 56
• arp, page 57
• arp flooding, page 58
• asn, page 59
• attach-avs, page 60
• attribute-logical-expression, page 61
• attribute, page 62
• authenticate, page 63
• authentication-key-timeout, page 64
• authentication-key, page 66
• authentication, page 69
• auto-cost, page 72
• auto-route-target, page 73
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)6
A Commands
• autonomous-system, page 74
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 7
A Commands
aaa authentication login consoleaaa authentication login console
Description: Configure console methods
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login console
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)8
A Commandsaaa authentication login console
aaa authentication login defaultaaa authentication login default
Description: Configure default methods
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 9
A Commandsaaa authentication login default
aaa authentication login domainaaa authentication login domain <WORD>
Description: Configure domain methods
Syntax:
Login domain nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)10
A Commandsaaa authentication login domain
aaa authentication login fallback-checkaaa authentication login fallback-check
Description: checks if default auth servers are active or not before allowing fallback login
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login fallback-check
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 11
A Commandsaaa authentication login fallback-check
aaa authentication login ping-checkaaa authentication login ping-check
Description: Enables ICMP health check of AAA servers
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login ping-check
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)12
A Commandsaaa authentication login ping-check
aaa banneraaa banner <LINE>
Description: CLI informational banner to be displayed before user login (wrap with single quotes)
Syntax:
CLI informational banner to be displayed before user login (wrap withsingle quotes) (Max Size None)
LINE
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa banner <LINE>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 13
A Commandsaaa banner
aaa group server ldapaaa group server ldap <WORD>
Description: LDAP server group name.
Syntax:
LDAP server group nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa group server ldap <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)14
A Commandsaaa group server ldap
aaa group server radiusaaa group server radius <WORD>
Description: RADIUS server group name.
Syntax:
RADIUS server group nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa group server radius <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 15
A Commandsaaa group server radius
aaa group server tacacsplusaaa group server tacacsplus <WORD>
Description: TACACS+ server group name.
Syntax:
TACACS+ server group nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa group server tacacsplus <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)16
A Commandsaaa group server tacacsplus
aaa user default-roleaaa user default-role <default-role-policy>
Description: Default role assigned by aaa-admin for remote authentication
Syntax:
<default-role-policy><default-role-policy>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa user default-role <default-role-policy>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 17
A Commandsaaa user default-role
absoluteabsolute window <WORD>
Description: Absolute window configuration mode
Syntax:
Configure scheduler windowwindow
Window name (Max size 31)WORD
Command Mode: scheduler : Scheduler configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# absolute window <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)18
A Commandsabsolute
access-encapaccess-encap vlan <NUMBER>
Description: set the access-vlan for the qinq tunnel
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Command Mode: dot1q-tunnel : Tunnel configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# dot1q-tunnel <WORD>(config-tenant-tunnel)#access-encap vlan <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 19
A Commandsaccess-encap
access-groupaccess-group <WORD> <WORD> log
Description: Apply an access-list on this subject
Syntax:
Name of the access-list to apply (Max Size 64)WORD
DirectionsWORD
Log packets hitting the ACLlog
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# access-group <WORD> <WORD> log
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)20
A Commandsaccess-group
access-listaccess-list <WORD>
Description: Create access-list
Syntax:
Access-list Name (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 21
A Commandsaccess-list
account-statusaccount-status <WORD>
Description: Set The status of the locally-authenticated user account.
Syntax:
status of the locally-authenticated user accountWORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# account-status <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)22
A Commandsaccount-status
actionaction merge|replace
Description: Snapshot import action merge|replace
Syntax:
Merge with existing configurationmerge
Replace existing configurationreplace
Command Mode: snapshot import : Configuration import setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# action merge|replace
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 23
A Commandsaction
active-flow-timeoutactive-flow-timeout <activeFlowTimeout>
Description: Configure Active Flow TimeOut
Syntax:
Configure Active Flow TimeOut. Number range from=60 to=3600activeFlowTimeout
Command Mode: flow exporter : Configure NetFlow Exporter Policy
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-dvs(config-vmware-dvs)# flow exporter <WORD>(config-vmware-dvs-flow-exporter)# active-flow-timeout <activeFlowTimeout>
active-flow-timeout <activeFlowTimeout>
Description: Configure Active Flow TimeOut
Syntax:
Configure Active Flow TimeOut. Number range from=60 to=3600activeFlowTimeout
Command Mode: flow exporter : Configure NetFlow Exporter Policy
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# flow exporter <WORD>(config-vmware-avs-flow-exporter)# active-flow-timeout <activeFlowTimeout>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)24
A Commandsactive-flow-timeout
address-familyaddress-family ipv4|ipv6 unicast
Description: Address Family
Syntax:
IPv4 address familyipv4
IPv6 address familyipv6
Unicast delivery modelunicast
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# address-family ipv4|ipv6 unicast
address-family ipv4|ipv6 unicast
Description: EIGRP Policy Address Family
Syntax:
Address Family IPv4ipv4
Address Family IPv6ipv6
Unicastunicast
Command Mode: vrf : Configure VRF information
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast
address-family ipv4|ipv6|l2vpn unicast|evpn
Description: Configure an address-family for peer
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 25
A Commandsaddress-family
Configure IPv4 address-familyipv4
Configure IPv6 address-familyipv6
Configure l2vpn address-familyl2vpn
Configure Unicast sub-address-familyunicast
Configure EVPN sub-address-familyevpn
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6|l2vpn unicast|evpn
address-family ipv4|ipv6 unicast
Description: Configure an address-family
Syntax:
Configure IPv4 address-familyipv4
Configure IPv6 address-familyipv6
Configure unicast address-familyunicast
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast
address-family ipv4|ipv6 unicast
Description: Address Family
Syntax:
IPv4 address familyipv4
IPv6 address familyipv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)26
A Commandsaddress-family
Unicast delivery modelunicast
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# address-family ipv4|ipv6 unicast
address-family ipv4|ipv6 unicast
Description: EIGRP Policy Address Family
Syntax:
Address Family IPv4ipv4
Address Family IPv6ipv6
Unicastunicast
Command Mode: vrf : Configure VRF information
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast
address-family ipv4|ipv6|l2vpn unicast|evpn
Description: Configure an address-family for peer
Syntax:
Configure IPv4 address-familyipv4
Configure IPv6 address-familyipv6
Configure l2vpn address-familyl2vpn
Configure Unicast sub-address-familyunicast
Configure EVPN sub-address-familyevpn
Command Mode: neighbor : Configure a BGP neighbor
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 27
A Commandsaddress-family
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6|l2vpn unicast|evpn
address-family ipv4|ipv6 unicast
Description: Configure an address-family
Syntax:
Configure IPv4 address-familyipv4
Configure IPv6 address-familyipv6
Configure unicast address-familyunicast
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)28
A Commandsaddress-family
address-pool-refaddress-pool-ref <ippool>
Description: Configure External IP Address Pool
Syntax:
ippoolippool
Command Mode: l4l7 resource-pool : Configure L4-L7 Service Resource Pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 resource-pool <WORD>(config-resource-pool)# address-pool-ref <ippool>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 29
A Commandsaddress-pool-ref
address-pooladdress-pool <PoolName> <gateway-address>
Description: Configure Address Pool
Syntax:
Name of the poolPoolName
gateway-addressgateway-address
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# address-pool <PoolName> <gateway-address>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)30
A Commandsaddress-pool
address-rangeaddress-range <start> <end>
Description: Add Unicast Address Range
Syntax:
Start Addressstart
End Addressend
Command Mode: address-pool : Configure Address Pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# address-pool <PoolName> <gateway-address>(config-tenant-addrinst)# address-range <start> <end>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 31
A Commandsaddress-range
addressaddress <A.B.C.D> [preferred]
Description: Configure the IP address for dns servers
Syntax:
IP Unicast address in format i.i.i.iA.B.C.D
(Optional) Configure the address to be preferredpreferred
Command Mode: dns : Configure default dns policy
Command Path:
# configure [['terminal', 't']](config)# dns(config-dns)# address <A.B.C.D> [preferred]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)32
A Commandsaddress
admin-state-enableadmin-state-enable
Description: Enable the state of the SSH communication service
Command Mode: ssh-service : SSH communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# ssh-service(config-ssh-service)# admin-state-enable
admin-state-enable
Description: Enable the state of the TELNET communication service
Command Mode: telnet : TELNET communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# telnet(config-telnet)# admin-state-enable
admin-state-enable
Description: Enable the state of the shellinabox communication service
Command Mode: shellinabox : SHELLINABOX communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# shellinabox(config-shellinabox)# admin-state-enable
admin-state-enable
Description: Enable the state of the HTTP communication service
Command Mode: http : HTTP communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# admin-state-enable
admin-state-enable
Description: Enable the state of the HTTPS communication service
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 33
A Commandsadmin-state-enable
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# admin-state-enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)34
A Commandsadmin-state-enable
adminadmin enable
Description: Set admin state of syslog group
Syntax:
Enableenable
Command Mode: logging : Logging server group configuration mode
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# admin enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 35
A Commandsadmin
advertise-subnetadvertise-subnet
Description: Advertise ip subnet instead of a host mask in the router LSA
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# advertise-subnet
advertise-subnet
Description: Advertise ip subnet instead of a host mask in the router LSA
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# advertise-subnet
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)36
A Commandsadvertise-subnet
aggregate-addressaggregate-address <IP-PREFIX/LEN> [as-set]
Description: Route summarization
Syntax:
Aggregate IPv4 address and mask lengthIP-PREFIX/LEN
(Optional) Autonomous system set path information and communityinformation
as-set
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# aggregate-address <IP-PREFIX/LEN> [as-set]
aggregate-address <IP-PREFIX/LEN> [as-set]
Description: Route summarization
Syntax:
Aggregate IPv4 address and mask lengthIP-PREFIX/LEN
(Optional) Autonomous system set path information and communityinformation
as-set
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# aggregate-address <IP-PREFIX/LEN> [as-set]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 37
A Commandsaggregate-address
allow-credentialallow-credential
Description: Enable HTTP Access-Control-Allow-Credentials header
Command Mode: http : HTTP communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# allow-credential
allow-credential
Description: Enable HTTPS Access-Control-Allow-Credentials header
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# allow-credential
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)38
A Commandsallow-credential
allow-originallow-origin <WORD>
Description: The URL to return in the Access-Control-Allow-Origin HTTP header
Syntax:
The URL to return in the Access-Control-Allow-Origin HTTP header(Max Size 256)
WORD
Command Mode: http : HTTP communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# allow-origin <WORD>
allow-origin <WORD>
Description: The URL to return in the Access-Control-Allow-Origin HTTPS header
Syntax:
The URL to return in the Access-Control-Allow-Origin HTTPS header(Max Size 256)
WORD
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# allow-origin <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 39
A Commandsallow-origin
allow-promiscuousallow-promiscuous enable
Description: Enable/disable promiscuous mode on trunk
Syntax:
enableenable
Command Mode: trunk-portgroup : Configure a trunk port group in the VMWare domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# trunk-portgroup <>(config-vmware-trunk)# allow-promiscuous enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)40
A Commandsallow-promiscuous
allow-self-asallow-self-as
Description: Accept as-path with my AS present in it
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# allow-self-as
allow-self-as
Description: Accept as-path with my AS present in it
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# allow-self-as
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 41
A Commandsallow-self-as
allow-writesallow-writes
Description: Allow writes for the RBAC rule
Command Mode: rbac rule : Create RBAC rule, security domain users can read subtree starting at specificobject
Command Path:
# configure [['terminal', 't']](config)# rbac rule <DN> <WORD>(config-rule)# allow-writes
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)42
A Commandsallow-writes
allowed-self-as-countallowed-self-as-count <NUMBER>
Description: The number of occurrences of a local access service network
Syntax:
Number of occurrences of AS number, default is 3. Number rangefrom=1 to=10
<1-10>
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# allowed-self-as-count <NUMBER>
allowed-self-as-count <NUMBER>
Description: The number of occurrences of a local access service network
Syntax:
Number of occurrences of AS number, default is 3. Number rangefrom=1 to=10
<1-10>
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# allowed-self-as-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 43
A Commandsallowed-self-as-count
analyticsanalytics cluster <WORD>
Description: Configure external analytics reachability information
Syntax:
Analytics cluster namecluster
Analytics cluster nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# analytics cluster <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)44
A Commandsanalytics
applicationapplication <WORD>
Description: application configuration mode
Syntax:
Application name (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>
application <WORD>
Description: application configuration mode
Syntax:
Application name (Max Size 64)WORD
Command Mode: dnssvrgrp : dnssvrgrp configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# dnssvrgrp <WORD>(config-tenant-dnssvrgrp)# application <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 45
A Commandsapplication
area default-costarea <A.B.C.D|NUMBER> default-cost <0-16777215>
Description: Set OSPF default area cost
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Cost value<0-16777215>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> default-cost <0-16777215>
area <A.B.C.D|NUMBER> default-cost <0-16777215>
Description: Set OSPF default area cost
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Cost value<0-16777215>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> default-cost <0-16777215>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)46
A Commandsarea default-cost
area interpodarea <A.B.C.D|NUMBER> interpod peering
Description: InterPod Peering
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
InterPod Peeringpeering
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> interpod peering
area <A.B.C.D|NUMBER> interpod peering
Description: InterPod Peering
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
InterPod Peeringpeering
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> interpod peering
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 47
A Commandsarea interpod
area l3outarea <A.B.C.D|NUMBER> l3out <l3out name>
Description: Enable OSPF in the L3Out
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Configure ASN on an API configured L3Out<l3out name>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> l3out <l3out name>
area <A.B.C.D|NUMBER> l3out <l3out name>
Description: Enable OSPF in the L3Out
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Configure ASN on an API configured L3Out<l3out name>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> l3out <l3out name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)48
A Commandsarea l3out
area loopbackarea <A.B.C.D|NUMBER> loopback <Loopback Ip Address>
Description: Configure OSPF on Loopback
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Loopback Ip<Loopback Ip Address>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> loopback <Loopback Ip Address>
area <A.B.C.D|NUMBER> loopback <Loopback Ip Address>
Description: Configure OSPF on Loopback
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Loopback Ip<Loopback Ip Address>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> loopback <Loopback Ip Address>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 49
A Commandsarea loopback
area nssaarea <A.B.C.D|NUMBER> nssa
Description: Configure area as nssa
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa
area <A.B.C.D|NUMBER> nssa
Description: Configure area as nssa
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)50
A Commandsarea nssa
area nssa default-information-originatearea <A.B.C.D|NUMBER> nssa default-information-originate [no-redistribute]
Description: Originate a default route
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
(Optional) No Redistribute area optionno-redistribute
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa default-information-originate[no-redistribute]
area <A.B.C.D|NUMBER> nssa default-information-originate [no-redistribute]
Description: Originate a default route
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
(Optional) No Redistribute area optionno-redistribute
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa default-information-originate[no-redistribute]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 51
A Commandsarea nssa default-information-originate
area nssa no-redistributearea <A.B.C.D|NUMBER> nssa no-redistribute [default-information-originate]
Description: Configure area as no-redistribute
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
(Optional) Originate a default routedefault-information-originate
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa no-redistribute[default-information-originate]
area <A.B.C.D|NUMBER> nssa no-redistribute [default-information-originate]
Description: Configure area as no-redistribute
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
(Optional) Originate a default routedefault-information-originate
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa no-redistribute[default-information-originate]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)52
A Commandsarea nssa no-redistribute
area nssa translatearea <A.B.C.D|NUMBER> nssa translate type7 suppress-fa
Description: Translate LSAs
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
From Type 7 to Type 5type7
Suppress forwarding address in translated LSAssuppress-fa
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa translate type7 suppress-fa
area <A.B.C.D|NUMBER> nssa translate type7 suppress-fa
Description: Translate LSAs
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
From Type 7 to Type 5type7
Suppress forwarding address in translated LSAssuppress-fa
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa translate type7 suppress-fa
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 53
A Commandsarea nssa translate
area rangearea <A.B.C.D|NUMBER> range <IP-PREFIX/LENGTH> [cost <cost>]
Description: Range
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Summarized IPIP-PREFIX/LENGTH
(Optional) Route costcost
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> range <IP-PREFIX/LENGTH> [cost <cost>]
area <A.B.C.D|NUMBER> range <IP-PREFIX/LENGTH> [cost <cost>]
Description: Range
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Summarized IPIP-PREFIX/LENGTH
(Optional) Route costcost
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> range <IP-PREFIX/LENGTH> [cost <cost>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)54
A Commandsarea range
area route-maparea <A.B.C.D|NUMBER> route-map <WORD> out|in
Description: Set Route Map
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Route Map Name (Max Size 63)WORD
Apply policy to outgoing routesout
Apply Policies for Incoming routein
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> route-map <WORD> out|in
area <A.B.C.D|NUMBER> route-map <WORD> out|in
Description: Set Route Map
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Route Map Name (Max Size 63)WORD
Apply policy to outgoing routesout
Apply Policies for Incoming routein
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> route-map <WORD> out|in
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 55
A Commandsarea route-map
area stubarea <A.B.C.D|NUMBER> stub
Description: Configure area as a stub
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> stub
area <A.B.C.D|NUMBER> stub
Description: Configure area as a stub
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> stub
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)56
A Commandsarea stub
arparp
Description: Config trust ARP in trust control policy
Command Mode: trust-control : Configuration for trust control policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# trust-control <WORD>(config-tenant-fhs-trustctrl)# arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 57
A Commandsarp
arp floodingarp flooding
Description: Enable ARP flooding
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# arp flooding
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)58
A Commandsarp flooding
asnasn <NUMBER>
Description: Configure BGP Autonomous System number
Syntax:
Number that uniquely identifies an autonomous system. Number rangefrom=1 to=4294967295
<1-4294967295>
Command Mode: bgp-fabric : Border Gateway Protocol (BGP)
Command Path:
# configure [['terminal', 't']](config)# bgp-fabric(config-bgp-fabric)# asn <NUMBER>
asn <NUMBER>
Description: Configure BGP Autonomous System number
Syntax:
Number that uniquely identifies an autonomous system. Number rangefrom=1 to=4294967295
<1-4294967295>
Command Mode: bgp : Border Gateway Protocol (BGP)
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# bgp fabric(config-pod-bgp)# asn <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 59
A Commandsasn
attach-avsattach-avs <OpflexDevid>
Description: Execute remote cli on an Opflex Device
Syntax:
Specify the OpFlex device<OpflexDevid>
Command Mode: exec : Exec Mode
Command Path:
# attach-avs <OpflexDevid>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)60
A Commandsattach-avs
attribute-logical-expressionattribute-logical-expression <logical-expression>
Description: Configure a logical expression as criteria
Syntax:
Enter a logical expression in the format: '<attributeType> <operator><attributeValue>' For custom-label, enter logical expression in theformat: 'custom <labelName> <operator> <labelValue>' For tags, enterlogical expression in the format: 'tag <operator> <categoryName><tagName>' - attributeType can take one of these values: vm-name,guest-os, hypervisor-id, vm-id, vnic, domain, datacenter, ip, mac -operator can take one of these values: equals, contains, startsWith,endsWith - operator should be 'equals' when attributeType is ip or mac- attributeValue, labelName, labelValue, categoryName and tagNameaccept a string - attributeValue can be 'use-epg-subnet' only whenattributeType is ip - A logical expression can be formed by combiningany of the above using 'AND'/'and'/'OR'/'or' - If any attribute valuecontains spaces or parenthesis, enclose it in backslashes ('\'). e.g.:attribute-logical-expression 'hypervisor-id equals host-123 OR tagcontains TCAT_1 TTAG_1 AND (guest-os equals \Ubuntu Linux(64-bit)\ and domain contains fex)' e.g.: attribute-logical-expression 'ipequals 10.1.1.10 or ip equals use-epg-subnet'
<logical-expression>
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute-logical-expression <logical-expression>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 61
A Commandsattribute-logical-expression
attributeattribute <WORD>
Description: An LDAP endpoint attribute to be used as the CiscoAVPair
Syntax:
LDAP endpoint attribute (Max Size 63)<WORD>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# attribute <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)62
A Commandsattribute
authenticateauthenticate
Description: Configure authentication for the default ntp policy
Command Mode: ntp : Configure the default ntp policy
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# ntp(config-ntp)# authenticate
authenticate
Description: Configure authentication for the default ntp policy
Command Mode: template ntp-fabric : Network Time Protocol (NTP)
Command Path:
# configure [['terminal', 't']](config)# template ntp-fabric <WORD>(config-template-ntp-fabric)# authenticate
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 63
A Commandsauthenticate
authentication-key-timeoutauthentication-key-timeout <NUMBER>
Description: Configure the authentication key timeout
Syntax:
Hold interval in seconds. Number range from=0 to=32767<0-32767>
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# authentication-key-timeout <NUMBER>
authentication-key-timeout <NUMBER>
Description: Configure the authentication key timeout
Syntax:
Hold interval in seconds. Number range from=0 to=32767<0-32767>
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# authentication-key-timeout <NUMBER>
authentication-key-timeout <NUMBER>
Description: Configure the authentication key timeout
Syntax:
Hold interval in seconds. Number range from=0 to=32767<0-32767>
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)64
A Commandsauthentication-key-timeout
(config-spine)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# authentication-key-timeout <NUMBER>
authentication-key-timeout <NUMBER>
Description: Configure the authentication key timeout
Syntax:
Hold interval in seconds. Number range from=0 to=32767<0-32767>
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# authentication-key-timeout <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 65
A Commandsauthentication-key-timeout
authentication-keyauthentication-key <id> [md5 <md5>]
Description: Configure ntp authentication keys for the default ntp policy
Syntax:
Id for the authentication key. Number range from=1 to=65535id
(Optional) Configure the authentication key (Max Size 510)md5
Command Mode: ntp : Configure the default ntp policy
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# ntp(config-ntp)# authentication-key <id> [md5 <md5>]
authentication-key <id> [md5 <md5>]
Description: Configure ntp authentication keys for the default ntp policy
Syntax:
Id for the authentication key. Number range from=1 to=65535id
(Optional) Configure the authentication key (Max Size 510)md5
Command Mode: template ntp-fabric : Network Time Protocol (NTP)
Command Path:
# configure [['terminal', 't']](config)# template ntp-fabric <WORD>(config-template-ntp-fabric)# authentication-key <id> [md5 <md5>]
authentication-key <LINE>
Description: Configure the authentication key
Syntax:
authentication keyLINE
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)66
A Commandsauthentication-key
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# authentication-key <LINE>
authentication-key <LINE>
Description: Configure the authentication key
Syntax:
authentication keyLINE
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# authentication-key <LINE>
authentication-key <LINE>
Description: Configure the authentication key
Syntax:
authentication keyLINE
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# authentication-key <LINE>
authentication-key <LINE>
Description: Configure the authentication key
Syntax:
authentication keyLINE
Command Mode: hsrp group : Configure HSRP Group
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 67
A Commandsauthentication-key
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# authentication-key <LINE>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)68
A Commandsauthentication-key
authenticationauthentication type compatible|strict
Description: Configure COOP authentication type
Syntax:
Configure COOP authentication typetype
Compatible typecompatible
Strict typestrict
Command Mode: coop-fabric : Council Of Oracles Protocol (COOP)
Command Path:
# configure [['terminal', 't']](config)# coop-fabric(config-coop-fabric)# authentication type compatible|strict
authentication type compatible|strict
Description: Configure COOP authentication type
Syntax:
Configure COOP authentication typetype
Compatible typecompatible
Strict typestrict
Command Mode: coop : COOP protocol
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# coop fabric(config-pod-coop)# authentication type compatible|strict
authentication simple|md5
Description: Authentication
Syntax:
Plain text authenticationsimple
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 69
A Commandsauthentication
Use MD5 authenticationmd5
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# authentication simple|md5
authentication simple|md5
Description: Authentication
Syntax:
Plain text authenticationsimple
Use MD5 authenticationmd5
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# authentication simple|md5
authentication simple|md5
Description: Authentication
Syntax:
Plain text authenticationsimple
Use MD5 authenticationmd5
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# authentication simple|md5
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)70
A Commandsauthentication
authentication simple|md5
Description: Authentication
Syntax:
Plain text authenticationsimple
Use MD5 authenticationmd5
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# authentication simple|md5
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 71
A Commandsauthentication
auto-costauto-cost reference-bandwidth <NUMBER>
Description: Set OSPF Policy Bandwidth Reference
Syntax:
OSPF Policy Bandwidth Referencereference-bandwidth
BandwidthReferenceValue inMbps. Number range from=1 to=4000000<1-4000000>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# auto-cost reference-bandwidth <NUMBER>
auto-cost reference-bandwidth <NUMBER>
Description: Set OSPF Policy Bandwidth Reference
Syntax:
OSPF Policy Bandwidth Referencereference-bandwidth
BandwidthReferenceValue inMbps. Number range from=1 to=4000000<1-4000000>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# auto-cost reference-bandwidth <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)72
A Commandsauto-cost
auto-route-targetauto-route-target
Description: Configure Route Target
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# auto-route-target
auto-route-target
Description: Configure Route Target
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# auto-route-target
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 73
A Commandsauto-route-target
autonomous-systemautonomous-system <NUMBER> [l3out <l3out>]
Description: Autonomous System Configuration for EIGRP
Syntax:
The autonomous system number. Number range from=1 to=65535<1-65535>
(Optional) Configure ASN on an API configured L3Outl3out
Command Mode: vrf : Configure VRF information
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# autonomous-system <NUMBER> [l3out <l3out>]
autonomous-system <NUMBER> [l3out <l3out>]
Description: Autonomous System Configuration for EIGRP
Syntax:
The autonomous system number. Number range from=1 to=65535<1-65535>
(Optional) Configure ASN on an API configured L3Outl3out
Command Mode: vrf : Configure VRF information
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# autonomous-system <NUMBER> [l3out <l3out>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)74
A Commandsautonomous-system
B Commands
• bandwidth, page 76
• basedn, page 77
• bash, page 78
• bd-enf-exp-ip, page 79
• bd-enforce, page 80
• bfd, page 81
• bfd ip ipv6 authentication, page 83
• bfd ip ipv6 inherit, page 86
• bfd ip ipv6 tenant, page 88
• bgp-fabric, page 90
• bgp, page 91
• binddn, page 93
• bpdu-filter, page 94
• breakout, page 95
• bridge-domain-match, page 97
• bridge-domain, page 98
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 75
bandwidthbandwidth <NUMBER>
Description: Set the desired bandwidth to police to
Syntax:
Bandwidth percentage guaranteed as %. Number range from=0 to=100<0-100>
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# bandwidth <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)76
B Commandsbandwidth
basednbasedn <WORD>
Description: The LDAP base DN for user lookup in the LDAP directory tree
Syntax:
user lookup in LDAP directory tree (Max Size 127)<WORD>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# basedn <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 77
B Commandsbasedn
bashbash
Description: Bash shell for unix commands
Command Mode: exec : Exec Mode
Command Path:
# bash
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)78
B Commandsbash
bd-enf-exp-ipbd-enf-exp-ip add <ip>
Description: Enable Enforced BD Flag
Syntax:
BD Enforce Exception ipadd
ipip
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# bd-enf-exp-ip add <ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 79
B Commandsbd-enf-exp-ip
bd-enforcebd-enforce enable
Description: Enable Enforced BD Flag
Syntax:
Enable BD Enforcingenable
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# bd-enforce enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)80
B Commandsbd-enforce
bfdbfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# bfd enable
bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# bfd enable
bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 81
B Commandsbfd
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# bfd enable
bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# bfd enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)82
B Commandsbfd
bfd ip ipv6 authenticationbfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
Description: Configure BFD authentication
Syntax:
IPv4ip
IPv6ipv6
Configure Keyed SHA1 authenticationkeyed-sha1
Configure authentication key IDkeyid
Authentication key ID. Number range from=1 to=255<keyid>
Configure shared authentication keykey
Shared authentication key (Max Size 20)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
Description: Configure BFD authentication
Syntax:
IPv4ip
IPv6ipv6
Configure Keyed SHA1 authenticationkeyed-sha1
Configure authentication key IDkeyid
Authentication key ID. Number range from=1 to=255<keyid>
Configure shared authentication keykey
Shared authentication key (Max Size 20)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 83
B Commandsbfd ip ipv6 authentication
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
Description: Configure BFD authentication
Syntax:
IPv4ip
IPv6ipv6
Configure Keyed SHA1 authenticationkeyed-sha1
Configure authentication key IDkeyid
Authentication key ID. Number range from=1 to=255<keyid>
Configure shared authentication keykey
Shared authentication key (Max Size 20)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
Description: Configure BFD authentication
Syntax:
IPv4ip
IPv6ipv6
Configure Keyed SHA1 authenticationkeyed-sha1
Configure authentication key IDkeyid
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)84
B Commandsbfd ip ipv6 authentication
Authentication key ID. Number range from=1 to=255<keyid>
Configure shared authentication keykey
Shared authentication key (Max Size 20)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 85
B Commandsbfd ip ipv6 authentication
bfd ip ipv6 inheritbfd ip|ipv6 inherit interface-policy <WORD>
Description: Inherit BFD interface template policy
Syntax:
IPv4ip
IPv6ipv6
Associate the interface with a BFD interface policyinterface-policy
Policy nameWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 inherit interface-policy <WORD>
bfd ip|ipv6 inherit interface-policy <WORD>
Description: Inherit BFD interface template policy
Syntax:
IPv4ip
IPv6ipv6
Associate the interface with a BFD interface policyinterface-policy
Policy nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 inherit interface-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)86
B Commandsbfd ip ipv6 inherit
bfd ip|ipv6 inherit interface-policy <WORD>
Description: Inherit BFD interface template policy
Syntax:
IPv4ip
IPv6ipv6
Associate the interface with a BFD interface policyinterface-policy
Policy nameWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 inherit interface-policy <WORD>
bfd ip|ipv6 inherit interface-policy <WORD>
Description: Inherit BFD interface template policy
Syntax:
IPv4ip
IPv6ipv6
Associate the interface with a BFD interface policyinterface-policy
Policy nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 inherit interface-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 87
B Commandsbfd ip ipv6 inherit
bfd ip ipv6 tenantbfd ip|ipv6 tenant mode
Description: Enable BFD Tenant Mode
Syntax:
IPv4ip
IPv6ipv6
Modemode
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 tenant mode
bfd ip|ipv6 tenant mode
Description: Enable BFD Tenant Mode
Syntax:
IPv4ip
IPv6ipv6
Modemode
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 tenant mode
bfd ip|ipv6 tenant mode
Description: Enable BFD Tenant Mode
Syntax:
IPv4ip
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)88
B Commandsbfd ip ipv6 tenant
IPv6ipv6
Modemode
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 tenant mode
bfd ip|ipv6 tenant mode
Description: Enable BFD Tenant Mode
Syntax:
IPv4ip
IPv6ipv6
Modemode
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 tenant mode
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 89
B Commandsbfd ip ipv6 tenant
bgp-fabricbgp-fabric
Description: Border Gateway Protocol (BGP)
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# bgp-fabric
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)90
B Commandsbgp-fabric
bgpbgp fabric
Description: Border Gateway Protocol (BGP)
Syntax:
Fabric BGP configurationfabric
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# bgp fabric
bgp evpn peering [type <type>] [password <password>]
Description: BGP EVPN Peering Profile
Syntax:
BGP EVPN Peering Profileevpn
BGP EVPN Peering Profilepeering
(Optional) BGP EVPN Peering typetype
(Optional) BGP EVPN Peering Passwordpassword
Command Mode: fabric-external : Intrasite/Intersite Connectivity Profile
Command Path:
# configure [['terminal', 't']](config)# fabric-external <NUMBER>(config-fabric-external)# bgp evpn peering [type <type>] [password <password>]
bgp evpn peering [type <type>] [password <password>]
Description: BGP EVPN Peering Profile
Syntax:
BGP EVPN Peering Profileevpn
BGP EVPN Peering Profilepeering
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 91
B Commandsbgp
(Optional) BGP EVPN Peering typetype
(Optional) BGP EVPN Peering Passwordpassword
Command Mode: pod : Pod Profile
Command Path:
# configure [['terminal', 't']](config)# fabric-external <NUMBER>(config-fabric-external)# pod <NUMBER>(config-fabric-external-pod)# bgp evpn peering [type <type>] [password <password>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)92
B Commandsbgp
binddnbinddn <WORD>
Description: The LDAP bind DN for user lookup in the LDAP directory tree
Syntax:
user lookup in LDAP directory tree (Max Size 127)<WORD>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# binddn <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 93
B Commandsbinddn
bpdu-filterbpdu-filter
Description: Enable BPDU filter for extended chassis ports
Command Mode: spanning-tree : STP MST configuration mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# bpdu-filter
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)94
B Commandsbpdu-filter
breakoutbreakout <breakout-map>
Description: Configure breakout ports
Syntax:
Breakout Map<breakout-map>
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# breakout <breakout-map>
breakout <breakout-map>
Description: Configure breakout ports
Syntax:
Breakout Map<breakout-map>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# breakout <breakout-map>
breakout <breakout-map>
Description: Configure breakout ports
Syntax:
Breakout Map<breakout-map>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 95
B Commandsbreakout
(config-leaf-if)# breakout <breakout-map>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)96
B Commandsbreakout
bridge-domain-matchbridge-domain-match
Description: Remove the global default-export route-profile
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# bridge-domain-match
bridge-domain-match
Description: Remove the global default-export route-profile
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# bridge-domain-match
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 97
B Commandsbridge-domain-match
bridge-domainbridge-domain <WORD>
Description: Configuration for bridge-domain
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>
bridge-domain member <WORD>
Description: Bind the EPG to a bridge-domain
Syntax:
Bind the EPG to a bridge-domainmember
bridge-domain to associate (Max Size 64)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# bridge-domain member <WORD>
bridge-domain <WORD>
Description: Bind the EPG to a bridge-domain
Syntax:
bridge domain associated with epg suggestion use "inb"WORD
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)98
B Commandsbridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# bridge-domain <WORD>
bridge-domain member <WORD>
Description: Bind the EPG to a bridge-domain
Syntax:
Bind the EPG to a bridge-domainmember
bridge-domain to associate (Max Size 64)WORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# bridge-domain member <WORD>
bridge-domain tenant <tenant> name <name>
Description: Configure Bridge Domain for a L4-L7 Graph Connector.
Syntax:
Tenant in which the bridge domain is availabletenant
Tenant in which the bridge domain is available<tenant>
Bridge domain namename
Name of bd<name>
Command Mode: connector : Configure Connector for a Service Node
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>] [svcredir <Service Redirection>] [service-type <Service Type>](config-service)# connector <WORD> [cluster-interface <WORD>](config-connector)# bridge-domain tenant <tenant> name <name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 99
B Commandsbridge-domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)100
B Commandsbridge-domain
C Commands
• callhome, page 104
• callhome test info notice emergency alert critical error debug warning node, page 105
• catalog-version, page 106
• cdp, page 107
• cert-chain, page 111
• cert, page 112
• certificate, page 113
• channel-group, page 114
• channel-mode, page 116
• ciphers, page 119
• clear-encryption-key, page 120
• clear-pwd-history, page 121
• clear core-status controller, page 122
• clear core-status switch, page 123
• clear core controller, page 124
• clear core switch, page 125
• clear endpoints leaf tenant bridge-domain, page 126
• clear endpoints leaf tenant bridge-domain vlan, page 127
• clear endpoints leaf tenant vrf, page 128
• clear firmware, page 129
• clear snapshot file, page 130
• clear snapshot job, page 131
• clear techsupport controllers, page 132
• clear techsupport switch, page 133
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 101
• clear troubleshoot epext session report, page 134
• clear troubleshoot eptoep session report, page 135
• clock display-format, page 136
• clock show-offset, page 137
• clock timezone, page 138
• cluster-device, page 139
• cluster-interface, page 140
• collect, page 141
• comm-policy, page 142
• community-list expanded, page 143
• community-list standard, page 144
• configure-avs, page 145
• configure-dvs, page 146
• configure, page 147
• connection intra-service, page 148
• connection intra-service service1 connector1 service2 connector2 copyservice, page 149
• connection terminal provider consumer service, page 150
• connection terminal provider consumer service connector copyservice, page 151
• connection terminal provider consumer terminal provider consumer copyservice, page 152
• connector, page 153
• console, page 154
• consumer, page 155
• contract-id, page 156
• contract, page 157
• contract consumer, page 158
• contract deny, page 161
• contract enforce, page 163
• contract intra-epg, page 164
• contract provider, page 165
• controller-group, page 168
• controller, page 169
• coop-fabric, page 170
• coop, page 171
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)102
C Commands
• copp-aggr, page 172
• cos enable, page 173
• cos value, page 174
• cost, page 175
• country, page 176
• crypto aes, page 177
• crypto ca, page 178
• crypto keyring, page 179
• crypto webtoken, page 180
• csr, page 181
• customer-id, page 182
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 103
C Commands
callhomecallhome common
Description: Callhome common policy configuration mode
Syntax:
Callhome common policy configuration modecommon
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# callhome common
callhome test info|notice|emergency|alert|critical|error|debug|warning
Description: Send callhome test message
Syntax:
Send callhome test messagetest
Infoinfo
Noticenotice
Emergencyemergency
Alertalert
Criticalcritical
Errorerror
Debugdebug
Warningwarning
Command Mode: exec : Exec Mode
Command Path:
# callhome test info|notice|emergency|alert|critical|error|debug|warning
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)104
C Commandscallhome
callhome test info notice emergency alert critical error debugwarning node
callhome test info|notice|emergency|alert|critical|error|debug|warning node <Source node>
Description: Source node
Syntax:
Send callhome test messagetest
Infoinfo
Noticenotice
Emergencyemergency
Alertalert
Criticalcritical
Errorerror
Debugdebug
Warningwarning
leaf or spine node. Number range from=0 to=9223372036854775807Source node
Command Mode: exec : Exec Mode
Command Path:
# callhome test info|notice|emergency|alert|critical|error|debug|warning node <Source node>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 105
C Commandscallhome test info notice emergency alert critical error debug warning node
catalog-versioncatalog-version <version>
Description: Change catalog version
Syntax:
firmware version<version>
Command Mode: firmware : Firmware upgrade configuration Mode
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# catalog-version <version>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)106
C Commandscatalog-version
cdpcdp enable|default
Description: Configure CDP parameters on DVS uplink ports
Syntax:
Enable CDPenable
Remove CDP override policydefault
Command Mode: configure-dvs : Configure a VMWare Domain as DVS type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-dvs(config-vmware-dvs)# cdp enable|default
cdp enable|default
Description: Configure CDP parameters on AVS uplink ports
Syntax:
Enable CDPenable
Remove CDP override policydefault
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# cdp enable|default
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: template policy-group : Configure Policy Group Parameters
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 107
C Commandscdp
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# cdp enable
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# cdp enable
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: template spine-interface-policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template spine-interface-policy-group <WORD>(config-spine-if-pol-grp)# cdp enable
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)108
C Commandscdp
(config-leaf-if)# cdp enable
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# cdp enable
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# cdp enable
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# cdp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 109
C Commandscdp
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# cdp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)110
C Commandscdp
cert-chaincert-chain <WORD>
Description: Set The PEM-encoded chain of trust from the trustpoint to a trusted root authority.
Syntax:
The PEM-encoded chain of trust from the trustpoint to a trusted rootauthority
<WORD>
Command Mode: crypto ca : Configure certificate authority related information
Command Path:
# configure [['terminal', 't']](config)# crypto ca <WORD>(config-ca)# cert-chain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 111
C Commandscert-chain
certcert <CERTIFICATE>
Description: Provide a certificate, that contains public key and signed information.
Syntax:
Provide a certificate in quotes, that contains public key and signedinformation
<CERTIFICATE>
Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# cert <CERTIFICATE>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)112
C Commandscert
certificatecertificate <WORD>
Description: Create AAA user certificate in X.509 format.
Syntax:
Name for the user certificateWORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# certificate <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 113
C Commandscertificate
channel-groupchannel-group <WORD> [vpc]
Description: Create Port Channel
Syntax:
Port-Channel/VPC Name (Max Size 64)WORD
(Optional) Configure channel-group as VPCvpc
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# channel-group <WORD> [vpc]
channel-group <WORD> [vpc]
Description: Configure Port Channel on Fex
Syntax:
Port-Channel/VPC Name (Max Size 64)WORD
(Optional) Create the channel-group as a VPCvpc
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# channel-group <WORD> [vpc]
channel-group <WORD> [vpc]
Description: Associate a Channel Group to this Interface
Syntax:
Port-Channel/VPC Name (Max Size 64)WORD
(Optional) Create the channel-group as a VPCvpc
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)114
C Commandschannel-group
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# channel-group <WORD> [vpc]
channel-group <WORD> [vpc]
Description: Associate a Channel Group to this Interface
Syntax:
Port-Channel/VPC Name (Max Size 64)WORD
(Optional) Create the channel-group as a VPCvpc
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# channel-group <WORD> [vpc]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 115
C Commandschannel-group
channel-modechannel-mode on|active|passive|mac-pinning
Description: Configure LACP mode override on DVS uplink ports
Syntax:
Set channeling mode to ON (static)on
Set channeling mode to ACTIVEactive
Set channeling mode to PASSIVEpassive
Set channeling mode to MAC-PINNINGmac-pinning
Command Mode: configure-dvs : Configure a VMWare Domain as DVS type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-dvs(config-vmware-dvs)# channel-mode on|active|passive|mac-pinning
channel-mode on|active|passive|mac-pinning
Description: Configure LACP mode override on AVS uplink ports
Syntax:
Set channeling mode to ON (static)on
Set channeling mode to ACTIVEactive
Set channeling mode to PASSIVEpassive
Set channeling mode to MAC-PINNINGmac-pinning
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# channel-mode on|active|passive|mac-pinning
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)116
C Commandschannel-mode
channel-mode on|active|passive|mac-pinning
Description: Configure channeling mode
Syntax:
Set channeling mode to ON (static)on
Set channeling mode to ACTIVEactive
Set channeling mode to PASSIVEpassive
Set channeling mode to MAC-PINNINGmac-pinning
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# channel-mode on|active|passive|mac-pinning
channel-mode on|active|passive|mac-pinning
Description: Configure channeling mode
Syntax:
Set channeling mode to ON (static)on
Set channeling mode to ACTIVEactive
Set channeling mode to PASSIVEpassive
Set channeling mode to MAC-PINNINGmac-pinning
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# channel-mode on|active|passive|mac-pinning
channel-mode on|active|passive|mac-pinning
Description: Configure channeling mode
Syntax:
Set channeling mode to ON (static)on
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 117
C Commandschannel-mode
Set channeling mode to ACTIVEactive
Set channeling mode to PASSIVEpassive
Set channeling mode to MAC-PINNINGmac-pinning
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# channel-mode on|active|passive|mac-pinning
channel-mode on|active|passive|mac-pinning
Description: Configure channeling mode
Syntax:
Set channeling mode to ON (static)on
Set channeling mode to ACTIVEactive
Set channeling mode to PASSIVEpassive
Set channeling mode to MAC-PINNINGmac-pinning
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# channel-mode on|active|passive|mac-pinning
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)118
C Commandschannel-mode
ciphersciphers <WORD>
Description: HTTPS cipher suite
Syntax:
Provide a valid cipher nameWORD
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# ciphers <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 119
C Commandsciphers
clear-encryption-keyclear-encryption-key
Description: Clears AES encryption key
Command Mode: crypto aes : AES encryption configuration
Command Path:
# configure [['terminal', 't']](config)# crypto aes(config-aes)# clear-encryption-key
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)120
C Commandsclear-encryption-key
clear-pwd-historyclear-pwd-history
Description: Clears the password history of a locally-authenticated user
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# clear-pwd-history
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 121
C Commandsclear-pwd-history
clear core-status controllerclear core-status controller <NUMBER> <WORD>
Description: Remove exported core status and files for controllers
Syntax:
Controller id. Number range from=1 to=64<1-64>
Core status collection timeWORD
Command Mode: exec : Exec Mode
Command Path:
# clear core-status controller <NUMBER> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)122
C Commandsclear core-status controller
clear core-status switchclear core-status switch <NUMBER> <WORD>
Description: Remove exported core status and files for switches
Syntax:
Switch id. Number range from=101 to=4000<101-4000>
Core status collection timeWORD
Command Mode: exec : Exec Mode
Command Path:
# clear core-status switch <NUMBER> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 123
C Commandsclear core-status switch
clear core controllerclear core controller <NUMBER> <WORD>
Description: Remove core metadata information generated at a controller
Syntax:
Controller id. Number range from=1 to=64<1-64>
Core creation timeWORD
Command Mode: exec : Exec Mode
Command Path:
# clear core controller <NUMBER> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)124
C Commandsclear core controller
clear core switchclear core switch <NUMBER> <WORD>
Description: Remove core metadata information generated at a switch
Syntax:
Switch id. Number range from=101 to=4000<101-4000>
Core creation timeWORD
Command Mode: exec : Exec Mode
Command Path:
# clear core switch <NUMBER> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 125
C Commandsclear core switch
clear endpoints leaf tenant bridge-domainclear endpoints leaf <node-id> tenant <tenant-name> bridge-domain <bd-name>
Description: Clear Bridge-Domain Hosting the endpoints
Syntax:
Leaf Numberleaf
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
node-id
Tenant Hosting the endpoints (Max Size 63)tenant-name
Bridge-Domain Hosting the endpoints (Max Size 64)bd-name
Command Mode: exec : Exec Mode
Command Path:
# clear endpoints leaf <WORD> tenant <WORD> bridge-domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)126
C Commandsclear endpoints leaf tenant bridge-domain
clear endpoints leaf tenant bridge-domain vlanclear endpoints leaf <node-id> tenant <tenant-name> bridge-domain <WORD> vlan <NUMBER>
Description: Clear VLAN Hosting the endpoints
Syntax:
Leaf Numberleaf
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
node-id
Tenant Hosting the endpoints (Max Size 63)tenant-name
Bridge-Domain Hosting the endpoints (Max Size 64)bd-name
VLAN Hosting the endpoints. Number range from=1 to=4094<1-4094>
Command Mode: exec : Exec Mode
Command Path:
# clear endpoints leaf <WORD> tenant <WORD> bridge-domain <WORD> vlan <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 127
C Commandsclear endpoints leaf tenant bridge-domain vlan
clear endpoints leaf tenant vrfclear endpoints leaf <node-id> tenant <tenant-name> vrf <vrf-name>
Description: Clear VRF Hosting the endpoints
Syntax:
Leaf Numberleaf
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
node-id
Tenant Hosting the endpoints (Max Size 63)tenant-name
Name of the VRF Hosting the endpoints (Max Size 64)vrf-name
Command Mode: exec : Exec Mode
Command Path:
# clear endpoints leaf <WORD> tenant <WORD> vrf <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)128
C Commandsclear endpoints leaf tenant vrf
clear firmwareclear firmware upgrade scheduler-restrictions
Description: Clear firmware upgrade scheduler restrictions
Syntax:
upgradeupgrade
scheduler-restrictionsscheduler-restrictions
Command Mode: exec : Exec Mode
Command Path:
# clear firmware upgrade scheduler-restrictions
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 129
C Commandsclear firmware
clear snapshot fileclear snapshot file <WORD>
Description: Remove snapshot file
Syntax:
Snapshot file nameWORD
Command Mode: exec : Exec Mode
Command Path:
# clear snapshot file <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)130
C Commandsclear snapshot file
clear snapshot jobclear snapshot job <WORD>
Description: Remove snapshot job
Syntax:
Snapshot job nameWORD
Command Mode: exec : Exec Mode
Command Path:
# clear snapshot job <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 131
C Commandsclear snapshot job
clear techsupport controllersclear techsupport controllers <NUMBER> <WORD>
Description: Clear techsupport status for controllers
Syntax:
Controller id. Number range from=1 to=64<1-64>
Techsupport collection timeWORD
Command Mode: exec : Exec Mode
Command Path:
# clear techsupport controllers <NUMBER> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)132
C Commandsclear techsupport controllers
clear techsupport switchclear techsupport switch <NUMBER> <WORD>
Description: Clear techsupport status for switch
Syntax:
Switch id. Number range from=101 to=4000<101-4000>
Techsupport collection timeWORD
Command Mode: exec : Exec Mode
Command Path:
# clear techsupport switch <NUMBER> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 133
C Commandsclear techsupport switch
clear troubleshoot epext session reportclear troubleshoot epext session <ession_name> report
Description: Remove all non-pending reports of a troubleshoot session
Syntax:
sessionsession
Session nameession_name
Command Mode: exec : Exec Mode
Command Path:
# clear troubleshoot epext session <ession_name> report
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)134
C Commandsclear troubleshoot epext session report
clear troubleshoot eptoep session reportclear troubleshoot eptoep session <session_name> report
Description: Remove all non-pending reports of a troubleshoot session
Syntax:
sessionsession
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# clear troubleshoot eptoep session <session_name> report
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 135
C Commandsclear troubleshoot eptoep session report
clock display-formatclock display-format local|utc
Description: Configure Clock Display Format
Syntax:
Local display formatlocal
UTC display formatutc
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# clock display-format local|utc
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)136
C Commandsclock display-format
clock show-offsetclock show-offset enable
Description: Enable/Disable Display of the Offset
Syntax:
Enable/Disable Display of the Offset from UTCenable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# clock show-offset enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 137
C Commandsclock show-offset
clock timezoneclock timezone <timeZone>
Description: Configure clock timezone
Syntax:
The Timezone SelectiontimeZone
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# clock timezone <timeZone>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)138
C Commandsclock timezone
cluster-devicecluster-device <WORD> [vcenter <WORD>] [vm <WORD>]
Description: Configure L4-L7 Cluster Device
Syntax:
device name (Max Size 64)WORD
(Optional) vcenter name (Max Size 64)WORD
(Optional) vm name (Max Size 128)WORD
Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>] [context <context>] [trunking <enable|disable>](config-cluster)# cluster-device <WORD> [vcenter <WORD>] [vm <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 139
C Commandscluster-device
cluster-interfacecluster-interface <WORD> [vlan <NUMBER>]
Description: Configure L4-L7 Cluster Interface
Syntax:
Cluster interface name (Max Size 16)WORD
(Optional) Static Encap/VLAN to user for this cluster interface. Numberrange from=1 to=4094
<vlan>
Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>] [context <context>] [trunking <enable|disable>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)140
C Commandscluster-interface
collectcollect <arg>
Description: Configure collect
Syntax:
arg
Command Mode: flow record : Configure Netflow Record
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow record <WORD>(config-tn-flow-record)# collect <>
collect <arg>
Description: Configure collect
Syntax:
arg
Command Mode: flow record : Configure Netflow Record
Command Path:
# configure [['terminal', 't']](config)# flow record <WORD>(config-flow-record)# collect <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 141
C Commandscollect
comm-policycomm-policy <WORD>
Description: Configure any communication policy, ssh/telnet/shellinabox/http/https
Syntax:
Provide a communication policy nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)142
C Commandscomm-policy
community-list expandedcommunity-list expanded <WORD> <LINE>
Description: Configure expanded community list templates
Syntax:
Community list name (Max Size 64)WORD
Regular-expressionLINE
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route group <WORD> tenant <WORD>(config-route-group)# community-list expanded <WORD> <LINE>
community-list expanded <WORD> <LINE>
Description: Configure expanded community list templates
Syntax:
Community list name (Max Size 64)WORD
Regular-expressionLINE
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route group <WORD> tenant <WORD>(config-route-group)# community-list expanded <WORD> <LINE>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 143
C Commandscommunity-list expanded
community-list standardcommunity-list standard <WORD> ASN2:NN
Description: Configure standard community list templates
Syntax:
Community list name (Max Size 64)WORD
Community number aa:nn formatASN2:NN
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route group <WORD> tenant <WORD>(config-route-group)# community-list standard <WORD> ASN2:NN
community-list standard <WORD> ASN2:NN
Description: Configure standard community list templates
Syntax:
Community list name (Max Size 64)WORD
Community number aa:nn formatASN2:NN
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route group <WORD> tenant <WORD>(config-route-group)# community-list standard <WORD> ASN2:NN
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)144
C Commandscommunity-list standard
configure-avsconfigure-avs
Description: Configure a VMWare Domain as AVS (N1K) type
Command Mode: vmware-domain : Create a VMM VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 145
C Commandsconfigure-avs
configure-dvsconfigure-dvs
Description: Configure a VMWare Domain as DVS type
Command Mode: vmware-domain : Create a VMM VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-dvs
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)146
C Commandsconfigure-dvs
configureconfigure [['terminal', 't']]
Description: Configuration Mode
Syntax:
(Optional) configure using terminalterminal
(Optional) configure using terminalterminal
Command Mode: exec : Exec Mode
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 147
C Commandsconfigure
connection intra-serviceconnection <WORD> [peerconnect <Peer connectivity>] intra-service service1 <WORD> connector1 <WORD>service2 <WORD> connector2 <WORD>
Description: Configure L4-L7 connection between service nodes
Syntax:
Connection name (Max Size 64)WORD
(Optional) Configure connectivity to peerPeer connectivity
Service node 1service1
service-node-1 name (Max Size 64)WORD
Connector on service node 1 that connects to the connectionconnector1
service-node-1 connector name (Max Size 64)WORD
Service node 2service2
service-node-2 name (Max Size 64)WORD
Connector on service node 2 that connects to the connectionconnector2
service-node-2 connector name (Max Size 64)WORD
Command Mode: l4l7 graph : Configure L4-L7 Service Graph
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# connection <WORD> [peerconnect <Peer connectivity>] intra-service service1<WORD> connector1 <WORD> service2 <WORD> connector2 <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)148
C Commandsconnection intra-service
connection intra-service service1 connector1 service2connector2 copyservice
connection <WORD> [peerconnect <Peer connectivity>] intra-service service1 <WORD> connector1 <WORD>service2 <WORD> connector2 <WORD> copyservice <WORD> connector <WORD>
Description: Configure copy node and connector
Syntax:
Connection name (Max Size 64)WORD
(Optional) Configure connectivity to peerPeer connectivity
Service node 1service1
service-node-1 name (Max Size 64)WORD
Connector on service node 1 that connects to the connectionconnector1
service-node-1 connector name (Max Size 64)WORD
Service node 2service2
service-node-2 name (Max Size 64)WORD
Connector on service node 2 that connects to the connectionconnector2
service-node-2 connector name (Max Size 64)WORD
service node name (Max Size 64)WORD
Connector on the service node that connects to a terminal nodeconnector
connector name (Max Size 64)WORD
Command Mode: l4l7 graph : Configure L4-L7 Service Graph
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# connection <WORD> [peerconnect <Peer connectivity>] intra-service service1<WORD> connector1 <WORD> service2 <WORD> connector2 <WORD> copyservice <WORD> connector<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 149
C Commandsconnection intra-service service1 connector1 service2 connector2 copyservice
connection terminal provider consumer serviceconnection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumer service <WORD>connector <WORD>
Description: Configure service node that connects to a terminal node
Syntax:
Connection name (Max Size 64)WORD
(Optional) Configure connectivity to peerPeer connectivity
Provider terminalprovider
Consumer terminalconsumer
service node name (Max Size 64)WORD
Connector on the service node that connects to a terminal nodeconnector
connector name (Max Size 64)WORD
Command Mode: l4l7 graph : Configure L4-L7 Service Graph
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# connection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumerservice <WORD> connector <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)150
C Commandsconnection terminal provider consumer service
connection terminal provider consumer service connectorcopyservice
connection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumer service <WORD>connector <WORD> copyservice <WORD> connector <WORD>
Description: Configure copy node and connector
Syntax:
Connection name (Max Size 64)WORD
(Optional) Configure connectivity to peerPeer connectivity
Provider terminalprovider
Consumer terminalconsumer
service node name (Max Size 64)WORD
Connector on the service node that connects to a terminal nodeconnector
connector name (Max Size 64)WORD
service node name (Max Size 64)WORD
Connector on the service node that connects to a terminal nodeconnector
connector name (Max Size 64)WORD
Command Mode: l4l7 graph : Configure L4-L7 Service Graph
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# connection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumerservice <WORD> connector <WORD> copyservice <WORD> connector <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 151
C Commandsconnection terminal provider consumer service connector copyservice
connection terminal provider consumer terminal providerconsumer copyservice
connection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumer terminalprovider|consumer copyservice <WORD> connector <WORD>
Description: Configure copy node and connector
Syntax:
Connection name (Max Size 64)WORD
(Optional) Configure connectivity to peerPeer connectivity
Provider terminalprovider
Consumer terminalconsumer
Provider terminalprovider
Consumer terminalconsumer
service node name (Max Size 64)WORD
Connector on the service node that connects to a terminal nodeconnector
connector name (Max Size 64)WORD
Command Mode: l4l7 graph : Configure L4-L7 Service Graph
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# connection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumerterminal provider|consumer copyservice <WORD> connector <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)152
C Commandsconnection terminal provider consumer terminal provider consumer copyservice
connectorconnector <WORD> [cluster-interface <WORD>]
Description: Configure Connector for a Service Node
Syntax:
Connector name (Max Size 64)WORD
(Optional) Cluster Interface name (Max Size 16)WORD
Command Mode: service : Configure L4-L7 Service
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>] [svcredir <Service Redirection>] [service-type <Service Type>](config-service)# connector <WORD> [cluster-interface <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 153
C Commandsconnector
consoleconsole [severity severity <severity-value>] [format <format>]
Description: Enable the logging to console(switches only)
Syntax:
(Optional) The severity level for the logsseverity <severity-value>
(Optional) The format for the log messagesformat
Command Mode: logging : Logging server group configuration mode
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# console [severity severity <severity-value>] [format <format>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)154
C Commandsconsole
consumerconsumer epg-label <WORD>
Description: Add a consumer EPG label
Syntax:
EPG labelepg-label
EPG label name (Max Size 64)WORD
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# consumer epg-label <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 155
C Commandsconsumer
contract-idcontract-id <WORD>
Description: Service contract id of the customer
Syntax:
The contract id (Max Size 512) surrounded by quotesWORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# contract-id <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)156
C Commandscontract-id
contractcontract <WORD> [type <type>]
Description: Configure binary contracts between Application EPGs
Syntax:
Name of the contract to create (Max Size 64)WORD
(Optional) whitelist (permit) or blacklist(deny) or oob-mgmt type ofcontract
type
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 157
C Commandscontract
contract consumercontract consumer <WORD> [qos-class <WORD>]
Description: Add the supplied contract to be consumed by any AEPg on this VRF
Syntax:
Whitelist contract to consume (Max Size 64)WORD
(Optional) Qos LevelWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# contract consumer <WORD> [qos-class <WORD>]
contract consumer <WORD> [imported] [label <WORD>] [qos-class <WORD>]
Description: Add a contract consumed by this AEPg, along with an optional list of subject labels
Syntax:
Whitelist contract to consume (Max Size 64)WORD
(Optional) used for contracts imported from other tenantsimported
(Optional) Per-Contract label (Max Size 64)WORD
(Optional) Qos LevelWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# contract consumer <WORD> [imported] [label <WORD>] [qos-class<WORD>]
contract consumer <contractName> [imported] [label <WORD>]
Description: Add a contract consumed by this EPG, along with an optional list of subject labels
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)158
C Commandscontract consumer
Whitelist contract to consume<contractName>
(Optional) Used for contracts imported from other tenantsimported
(Optional) Per-Contract label (Max Size 64)WORD
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# contract consumer <contractName> [imported] [label <WORD>]
contract consumer <WORD> [imported] [label <WORD>]
Description: Add a contract consumed by this In-band Epg, along with an optional list of subject labels
Syntax:
Whitelist contract to consume (Max Size 64)WORD
(Optional) used for contracts imported from other tenantsimported
(Optional) Per-Contract label (Max Size 64)WORD
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# contract consumer <WORD> [imported] [label <WORD>]
contract consumer <WORD> [imported] [label <WORD>] [qos-class <WORD>]
Description: Add a contract consumed by this EPG, along with an optional list of subject labels
Syntax:
Whitelist contract to consume (Max Size 64)WORD
(Optional) used for contracts imported from other tenantsimported
(Optional) Per-Contract label (Max Size 64)WORD
(Optional) Qos LevelWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 159
C Commandscontract consumer
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# contract consumer <WORD> [imported] [label <WORD>] [qos-class<WORD>]
contract consumer <WORD> [imported]
Description: Add a consumer contract
Syntax:
Whitelist contract to consumeWORD
(Optional) Used for contracts imported from other tenantsimported
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# contract consumer <WORD> [imported]
contract consumer <WORD> [imported]
Description: Add a consumer contract
Syntax:
Whitelist contract to consumeWORD
(Optional) Used for contracts imported from other tenantsimported
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# contract consumer <WORD> [imported]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)160
C Commandscontract consumer
contract denycontract deny <WORD>
Description: Attach a taboo contract to this AEPg
Syntax:
Name of the blacklist contract (Max Size 64)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# contract deny <WORD>
contract deny <contractName>
Description: Attach a taboo contract to this EPG
Syntax:
Name of the blacklist contract<contractName>
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# contract deny <contractName>
contract deny <contractName>
Description: Attach a taboo contract to this InBand Epg
Syntax:
Name of the blacklist contract<contractName>
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 161
C Commandscontract deny
(config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# contract deny <contractName>
contract deny <WORD>
Description: Attach a taboo contract to this EPG
Syntax:
Name of the blacklist contract (Max Size 64)WORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# contract deny <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)162
C Commandscontract deny
contract enforcecontract enforce [ingress] [egress]
Description: Add a policy enforcement
Syntax:
(Optional) Policy will be applied at the Ingress Nodeingress
(Optional) Policy will be applied at the Egress Nodeegress
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# contract enforce [ingress] [egress]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 163
C Commandscontract enforce
contract intra-epgcontract intra-epg <WORD>
Description: Contract for controlling Intra-EPG traffic
Syntax:
Whitelist contract to apply (Max Size 64)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# contract intra-epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)164
C Commandscontract intra-epg
contract providercontract provider <WORD> [qos-class <WORD>]
Description: Add the supplied contract to be provided by any AEPg on this VRF
Syntax:
Whitelist contract provided (Max Size 64)WORD
(Optional) Qos LevelWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# contract provider <WORD> [qos-class <WORD>]
contract provider <WORD> [label <WORD>] [qos-class <WORD>]
Description: Contract provided by this AEPg, along with an optional list of subject labels
Syntax:
Whitelist contract to provide (Max Size 64)WORD
(Optional) Per-Contract label (Max Size 64)WORD
(Optional) Qos LevelWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# contract provider <WORD> [label <WORD>] [qos-class <WORD>]
contract provider <contractName> [label <WORD>]
Description: Add a contract provided by this EPG, along with an optional list of subject labels
Syntax:
Whitelist contract to provide<contractName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 165
C Commandscontract provider
(Optional) Per-Contract label (Max Size 64)WORD
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# contract provider <contractName> [label <WORD>]
contract provider <contractName> [label <label>]
Description: Add a contract provided by this AEPg, along with an optional list of subject labels
Syntax:
link to contract name<contractName>
(Optional)label
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# contract provider <contractName> [label <label>]
contract provider <WORD> [label <WORD>] [qos-class <WORD>]
Description: Add a contract provided by this EPG, along with an optional list of subject labels
Syntax:
Whitelist contract to provide (Max Size 64)WORD
(Optional) Per-Contract label (Max Size 64)WORD
(Optional) Qos LevelWORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# contract provider <WORD> [label <WORD>] [qos-class <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)166
C Commandscontract provider
contract provider <contractName>
Description: Add a contract provided by this AEPg, along with an optional list of subject labels
Syntax:
Name of the contract to be provided<contractName>
Command Mode: oob-mgmt : Creates/Modify the out of band mgmt under the tenant mgmt
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>(config-oob-epg)# contract provider <contractName>
contract provider <WORD>
Description: Add a provider contract
Syntax:
Whitelist contract to provideWORD
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# contract provider <WORD>
contract provider <WORD>
Description: Add a provider contract
Syntax:
Whitelist contract to provideWORD
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# contract provider <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 167
C Commandscontract provider
controller-groupcontroller-group
Description: Controller Upgrade Configuration Mode
Command Mode: firmware : Firmware upgrade configuration Mode
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# controller-group
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)168
C Commandscontroller-group
controllercontroller
Description: Configure Controller Node
Syntax:
arg
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# controller
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 169
C Commandscontroller
coop-fabriccoop-fabric
Description: Council Of Oracles Protocol (COOP)
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# coop-fabric
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)170
C Commandscoop-fabric
coopcoop fabric
Description: COOP protocol
Syntax:
Fabric COOP configurationfabric
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# coop fabric
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 171
C Commandscoop
copp-aggrcopp-aggr <arg>
Description: Add CoPP aggregate policy
Syntax:
arg
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# copp-aggr <>
copp-aggr <arg>
Description: Add CoPP aggregate policy
Syntax:
arg
Command Mode: template spine-policy-group : Configure Spine Policy Group
Command Path:
# configure [['terminal', 't']](config)# template spine-policy-group <WORD>(config-spine-policy-group)# copp-aggr <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)172
C Commandscopp-aggr
cos enablecos enable
Description: Enable Cos Marking
Command Mode: vmware-domain : Associate EPG to a VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>][allow-micro-segmentation] [deploy <WORD>] [push <WORD>] [delimiter <WORD>](config-tenant-app-epg-domain)# cos enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 173
C Commandscos enable
cos valuecos value <num>
Description: CoS value <0-7>
Syntax:
Class of Service. Number range from=0 to=7num
Command Mode: vmware-domain : Associate EPG to a VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>][allow-micro-segmentation] [deploy <WORD>] [push <WORD>] [delimiter <WORD>](config-tenant-app-epg-domain)# cos value <num>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)174
C Commandscos value
costcost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# cost <NUMBER>
cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# cost <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 175
C Commandscost
countrycountry <WORD>
Description: Set The two-letter ISO code for the country where the organization is located.
Syntax:
The two-letter ISO code for the country where the organization is located<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# country <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)176
C Commandscountry
crypto aescrypto aes
Description: AES encryption configuration
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# crypto aes
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 177
C Commandscrypto aes
crypto cacrypto ca <WORD>
Description: Configure certificate authority related information
Syntax:
Trustpoint label (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# crypto ca <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)178
C Commandscrypto ca
crypto keyringcrypto keyring <WORD>
Description: A keyring mode to create and hold an SSL certificate
Syntax:
Provide a keyring nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 179
C Commandscrypto keyring
crypto webtokencrypto webtoken
Description: The cryptographic data used for generating and verifying web tokens.
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# crypto webtoken
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)180
C Commandscrypto webtoken
csrcsr
Description: A csr mode to create and hold an SSL certificate
Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 181
C Commandscsr
customer-idcustomer-id <WORD>
Description: The customer id
Syntax:
The customer id (Max Size 512) surrounded by quotesWORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# customer-id <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)182
C Commandscustomer-id
D Commands
• data, page 185
• dead-interval, page 186
• debug-switch, page 187
• debug log reset, page 188
• debug log set, page 189
• decommission controller, page 190
• decommission switch, page 191
• default-information, page 192
• default-originate, page 194
• delay, page 195
• deny-mode, page 196
• deploy-epg tenant application epg qinq, page 197
• deploy-epg tenant application epg type, page 199
• deploy-epg tenant application epg vlan, page 201
• deployment-mode, page 203
• descr, page 204
• description, page 205
• destination-port, page 227
• destination-profile, page 228
• destination, page 229
• destination address, page 232
• destination destip, page 234
• destination epg, page 235
• destination external-l3 epg tenant l3out epg, page 237
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 183
• destination external-l3 epg tenant vrf epg, page 239
• destination interface, page 241
• destination tenant, page 242
• dhcp option, page 244
• dhcp relay policy, page 245
• dhcpv4-server, page 248
• dhcpv6-server, page 249
• dhparam, page 250
• direction, page 251
• disable-connected-check, page 254
• disable-peer-as-check, page 255
• distance, page 256
• dns, page 260
• dnssearchsuffix, page 261
• dnsservers, page 262
• dnssuffix, page 263
• dnssvr, page 264
• dnssvrgrp, page 265
• domain, page 266
• dot1q-tunnel, page 268
• dscp, page 269
• dsr-vip, page 271
• dsr, page 272
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)184
D Commands
datadata <LINE>
Description: Set A user public key in PEM format.
Syntax:
user public key in PEM format in quotes (Max Size None)LINE
Command Mode: ssh-key : Update ssh key for the user for ssh authentication
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# ssh-key <WORD>(config-ssh-key)# data <LINE>
data <CERTIFICATE>
Description: Set PEM encoded certificate
Syntax:
PEM encoded certificate in quotesCERTIFICATE
Command Mode: certificate : Create AAA user certificate in X.509 format.
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# certificate <WORD>(config-certificate)# data <CERTIFICATE>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 185
D Commandsdata
dead-intervaldead-interval <NUMBER>
Description: Dead interval
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# dead-interval <NUMBER>
dead-interval <NUMBER>
Description: Dead interval
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# dead-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)186
D Commandsdead-interval
debug-switchdebug-switch <NUMBER>
Description: Turn on debug mode for switch
Syntax:
Node ID. Number range from=101 to=4000<101-4000>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# debug-switch <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 187
D Commandsdebug-switch
debug log resetdebug <node-name> <process> log reset
Description: Reset the log levels to default log level
Syntax:
Node name<node-name>
Process name<process>
Command Mode: exec : Exec Mode
Command Path:
# debug <node-name> <process> log reset
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)188
D Commandsdebug log reset
debug log setdebug <node-name> <process> log set <topic> <level>
Description: Set log level for a topic
Syntax:
Node name<node-name>
Process name<process>
Topic name<topic>
Level name<level>
Command Mode: exec : Exec Mode
Command Path:
# debug <node-name> <process> log set <topic> <level>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 189
D Commandsdebug log set
decommission controllerdecommission controller <NUMBER>
Description: Decommission controller
Syntax:
Controller ID. Number range from=1 to=64<1-64>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# decommission controller <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)190
D Commandsdecommission controller
decommission switchdecommission switch <NUMBER> [remove-from-controller]
Description: Decommission switch
Syntax:
Node ID. Number range from=101 to=4000<101-4000>
(Optional) Remove the switch from controller (optional)remove-from-controller
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# decommission switch <NUMBER> [remove-from-controller]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 191
D Commandsdecommission switch
default-informationdefault-information originate [always]
Description: Control origination of a default route
Syntax:
Originate a default routeoriginate
(Optional) Always advertise default routealways
Command Mode: vrf : Configure VRF information
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# default-information originate [always]
default-information originate [always]
Description: Control origination of a default route
Syntax:
Originate a default routeoriginate
(Optional) Always advertise default routealways
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# default-information originate [always]
default-information originate [always]
Description: Control origination of a default route
Syntax:
Originate a default routeoriginate
(Optional) Always advertise default routealways
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)192
D Commandsdefault-information
Command Mode: vrf : Configure VRF information
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# default-information originate [always]
default-information originate [always]
Description: Control origination of a default route
Syntax:
Originate a default routeoriginate
(Optional) Always advertise default routealways
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# default-information originate [always]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 193
D Commandsdefault-information
default-originatedefault-originate
Description: Originate a default toward this peer
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# default-originate
default-originate
Description: Originate a default toward this peer
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# default-originate
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)194
D Commandsdefault-originate
delaydelay minimum|reload <NUMBER>
Description: HSRP initialization delay
Syntax:
Minimum delayminimum
Delay after reloadreload
Delay in seconds. Number range from=0 to=10000<0-10000>
Command Mode: template hsrp interface-policy : Configure HSRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template hsrp interface-policy <WORD> tenant <WORD>(config-template-hsrp-if-pol)# delay minimum|reload <NUMBER>
delay minimum|reload <NUMBER>
Description: HSRP initialization delay
Syntax:
Minimum delayminimum
Delay after reloadreload
Delay in seconds. Number range from=0 to=10000<0-10000>
Command Mode: template hsrp interface-policy : Configure HSRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template hsrp interface-policy <WORD> tenant <WORD>(config-template-hsrp-if-pol)# delay minimum|reload <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 195
D Commandsdelay
deny-modedeny-mode
Description:WhiteList or BlackList mode for EPG
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# deny-mode
deny-mode
Description:WhiteList or BlackList mode for EPG
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# deny-mode
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)196
D Commandsdeny-mode
deploy-epg tenant application epg qinqdeploy-epg tenant <WORD> application <WORD> epg <WORD> qinq outer-vlan <NUMBER> inner-vlan<NUMBER>
Description: Deploy regular AEPg on leaf with qinq(double encap)
Syntax:
Tenant hosting the AEPg to deploytenant
Tenant hosting the AEPg to deploy (Max Size 63)WORD
Application hosting the AEPg to deployapplication
Application Name (Max Size 64)WORD
AEPg to be deployed on the leafepg
EPg that uses the statically enabled Encap. (Max Size 64)WORD
Encapsulation Outer Vlanouter-vlan
Encapsulation Outer Vlan. Number range from=1 to=4094<1-4094>
Encapsulation Inner Vlaninner-vlan
Encapsulation Inner Vlan. Number range from=1 to=4094<1-4094>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# deploy-epg tenant <WORD> application <WORD> epg <WORD> qinq outer-vlan<NUMBER> inner-vlan <NUMBER>
deploy-epg tenant <WORD> application <WORD> epg <WORD> qinq outer-vlan <NUMBER> inner-vlan<NUMBER>
Description: Deploy regular AEPg on leaf with qinq(double encap)
Syntax:
Tenant hosting the AEPg to deploytenant
Tenant hosting the AEPg to deploy (Max Size 63)WORD
Application hosting the AEPg to deployapplication
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 197
D Commandsdeploy-epg tenant application epg qinq
Application Name (Max Size 64)WORD
AEPg to be deployed on the leafepg
EPg that uses the statically enabled Encap. (Max Size 64)WORD
Encapsulation Outer Vlanouter-vlan
Encapsulation Outer Vlan. Number range from=1 to=4094<1-4094>
Encapsulation Inner Vlaninner-vlan
Encapsulation Inner Vlan. Number range from=1 to=4094<1-4094>
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# deploy-epg tenant <WORD> application <WORD> epg <WORD> qinq outer-vlan<NUMBER> inner-vlan <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)198
D Commandsdeploy-epg tenant application epg qinq
deploy-epg tenant application epg typedeploy-epg tenant <WORD> application <WORD> epg <WORD> type micro-segmented
Description: Deploy micro-segmented AEPg on leaf
Syntax:
Tenant hosting the AEPg to deploytenant
Tenant hosting the AEPg to deploy (Max Size 63)WORD
Application hosting the AEPg to deployapplication
Application Name (Max Size 64)WORD
AEPg to be deployed on the leafepg
EPg that uses the statically enabled Encap. (Max Size 64)WORD
micro-segmented AEPgmicro-segmented
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# deploy-epg tenant <WORD> application <WORD> epg <WORD> type micro-segmented
deploy-epg tenant <WORD> application <WORD> epg <WORD> type micro-segmented
Description: Deploy micro-segmented AEPg on leaf
Syntax:
Tenant hosting the AEPg to deploytenant
Tenant hosting the AEPg to deploy (Max Size 63)WORD
Application hosting the AEPg to deployapplication
Application Name (Max Size 64)WORD
AEPg to be deployed on the leafepg
EPg that uses the statically enabled Encap. (Max Size 64)WORD
micro-segmented AEPgmicro-segmented
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 199
D Commandsdeploy-epg tenant application epg type
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# deploy-epg tenant <WORD> application <WORD> epg <WORD> type micro-segmented
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)200
D Commandsdeploy-epg tenant application epg type
deploy-epg tenant application epg vlandeploy-epg tenant <WORD> application <WORD> epg <WORD> vlan <NUMBER> vlan-domain member<WORD>
Description: Deploy regular AEPg on leaf
Syntax:
Tenant hosting the AEPg to deploytenant
Tenant hosting the AEPg to deploy (Max Size 63)WORD
Application hosting the AEPg to deployapplication
Application Name (Max Size 64)WORD
AEPg to be deployed on the leafepg
EPg that uses the statically enabled Encap. (Max Size 64)WORD
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Vlan Domain for Encapsulation Vlanvlan-domain
Vlan Domain for Encapsulation Vlanmember
vlan-domain to use to validate encapsulation vlan. (Max Size 64)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# deploy-epg tenant <WORD> application <WORD> epg <WORD> vlan <NUMBER>vlan-domain member <WORD>
deploy-epg tenant <WORD> application <WORD> epg <WORD> vlan <NUMBER> vlan-domain member<WORD>
Description: Deploy regular AEPg on leaf
Syntax:
Tenant hosting the AEPg to deploytenant
Tenant hosting the AEPg to deploy (Max Size 63)WORD
Application hosting the AEPg to deployapplication
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 201
D Commandsdeploy-epg tenant application epg vlan
Application Name (Max Size 64)WORD
AEPg to be deployed on the leafepg
EPg that uses the statically enabled Encap. (Max Size 64)WORD
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Vlan Domain for Encapsulation Vlanvlan-domain
Vlan Domain for Encapsulation Vlanmember
vlan-domain to use to validate encapsulation vlan. (Max Size 64)WORD
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# deploy-epg tenant <WORD> application <WORD> epg <WORD> vlan <NUMBER>vlan-domain member <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)202
D Commandsdeploy-epg tenant application epg vlan
deployment-modedeployment-mode <WORD>
Description: Set zone deployment mode
Syntax:
Zone Deployment ModeWORD
Command Mode: zone : Create zone policy
Command Path:
# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>(config-zone)# deployment-mode <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 203
D Commandsdeployment-mode
descrdescr <WORD>
Description: RADIUS server descr for authentication
Syntax:
descr for authentication (Max Size 128)<WORD>
Command Mode: radius-server host : RADIUS server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# descr <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)204
D Commandsdescr
descriptiondescription <description>
Description: Add a description to a power supply redundancy policy
Syntax:
Power supply redundancy policy description string<description>
Command Mode: power : Create a power supply redundancy policy
Command Path:
# configure [['terminal', 't']](config)# power redundancy-policy <WORD>(config-power)# description <description>
description <LINE>
Description: Set description
Syntax:
Set description, use single quotes with spaces ex: 'my descr' (Max Size128)
LINE
CommandMode: rbac security-domain : Create AAA security domain for processing authentication requests.
Command Path:
# configure [['terminal', 't']](config)# rbac security-domain <WORD>(config-security-domain)# description <LINE>
description <WORD>
Description: The description of callhome destination-profile
Syntax:
The description (Max Size 128) surrounded by single quotesWORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 205
D Commandsdescription
(config-callhome-destnprof)# description <WORD>
description <WORD>
Description: Add switch-group description
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# description <WORD>
description <STRING>
Description: Configure remote path description
Syntax:
DescriptionSTRING
Command Mode: remote : Remote path configuration mode
Command Path:
# configure [['terminal', 't']](config)# remote path <WORD>(config-remote)# description <STRING>
description <STRING>
Description: Configure description for the active ntp policy
Syntax:
DescriptionSTRING
Command Mode: ntp : Configure the default ntp policy
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# ntp(config-ntp)# description <STRING>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)206
D Commandsdescription
description <STRING>
Description: Configure STP description
Syntax:
DescriptionSTRING
Command Mode: region : STP MST region configuration mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>(config-stp-region)# description <STRING>
description <WORD>
Description: Description string, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# description <WORD>
description <WORD>
Description: Add fc-fabric-policy description
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: template fc-fabric-policy : Configure FC Fabric Policy(Max Size 64)
Command Path:
# configure [['terminal', 't']](config)# template fc-fabric-policy <WORD>(config-fc-fabric-policy)# description <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 207
D Commandsdescription
description <description>
Description: Update FC leaf policy description
Syntax:
<description>
Command Mode: template fc-leaf-policy : Configure FC Leaf Policy(Max Size 64)
Command Path:
# configure [['terminal', 't']](config)# template fc-leaf-policy <WORD>(config-fc-leaf-policy)# description <description>
description <STRING>
Description: Configure description for the active ntp policy
Syntax:
DescriptionSTRING
Command Mode: template ntp-fabric : Network Time Protocol (NTP)
Command Path:
# configure [['terminal', 't']](config)# template ntp-fabric <WORD>(config-template-ntp-fabric)# description <STRING>
description <description>
Description: Update Policy-Group Template description
Syntax:
<description>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# description <description>
description <description>
Description: Update Port-Channel Template description
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)208
D Commandsdescription
<description>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# description <description>
description <description>
Description: Update Spine-Interface-Policy-Group Template description
Syntax:
<description>
Command Mode: template spine-interface-policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template spine-interface-policy-group <WORD>(config-spine-if-pol-grp)# description <description>
description <WORD>
Description: Add a description string to a tenant, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# description <WORD>
description <WORD>
Description: Add a description on a contract, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Contract description, surrounded by single quotes if with spaces ex:'My descr' (Max Size 128)
WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 209
D Commandsdescription
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# description <WORD>
description <WORD>
Description: Add a description on a subject, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Subject description, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# description <WORD>
description <WORD>
Description: Add a description on a vrf, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
VRF description, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# description <WORD>
description <WORD>
Description: Add a description on an application, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)210
D Commandsdescription
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: application : application configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# description <WORD>
description <WORD>
Description: Add a description on an epg, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# description <WORD>
description <WORD>
Description: Add a description on an epg, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: dot1q-tunnel : Tunnel configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# dot1q-tunnel <WORD>(config-tenant-tunnel)#description <WORD>
description <epgDescr>
Description: Add a description on an epg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 211
D Commandsdescription
Syntax:
<epgDescr>
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# description <epgDescr>
description <WORD>
Description:Add a description on a bridge-domain, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Bridge-domain description, surrounded by single quotes if with spacesex: 'My descr' (Max Size 128)
WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# description <WORD>
description <WORD>
Description: Add a description on an epg, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# description <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)212
D Commandsdescription
description <epgDescr>
Description: Add a description on an epg
Syntax:
<epgDescr>
Command Mode: oob-mgmt : Creates/Modify the out of band mgmt under the tenant mgmt
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>(config-oob-epg)# description <epgDescr>
description <WORD>
Description: Add a description on a Redirection policy, surrounded by single quotes if with spaces ex: 'Mydescr'
Syntax:
Redirection Policy description, surrounded by single quotes if withspaces ex: 'My descr' (Max Size 128)
WORD
Command Mode: svcredir-pol : Configure L4L7 service redirection policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# svcredir-pol <WORD>(svcredir-pol)# description <WORD>
description <WORD>
Description: Description string, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# description <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 213
D Commandsdescription
description <LINE>
Description: Update igmp policy description
Syntax:
IGMP policy description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# description <LINE>
description <LINE>
Description: Update igmp snooping policy description
Syntax:
IGMP snooping policy description, use single quotes with spaces ex:'my descr' (Max Size 128)
LINE
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# description <LINE>
description <LINE>
Description: Update Netflow Exporter description
Syntax:
Netflow Exporter description, use single quotes with spaces ex: 'mydescr' (Max Size 128)
LINE
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transportudp <dstPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)214
D Commandsdescription
(config-tn-flow-exporter)# description <LINE>
description <LINE>
Description: Update Netflow Record description
Syntax:
NetflowRecord description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: flow record : Configure Netflow Record
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow record <WORD>(config-tn-flow-record)# description <LINE>
description <LINE>
Description: Update Netflow Monitor description
Syntax:
Netflow Monitor description, use single quotes with spaces ex: 'mydescr' (Max Size 128)
LINE
Command Mode: flow monitor : Configure Netflow Monitor
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow monitor <WORD>(config-tn-flow-monitor)# description <LINE>
description <LINE>
Description: Update Leaf Profile description
Syntax:
Leaf-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: leaf-profile : Configure Leaf Profile
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 215
D Commandsdescription
(config)# leaf-profile <WORD>(config-leaf-profile)# description <LINE>
description <LINE>
Description: Update Leaf Group description
Syntax:
Leaf-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: leaf-group : Configure Leaf Group
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# description <LINE>
description <LINE>
Description: Update Leaf Interface Profile description
Syntax:
Leaf-If-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: leaf-interface-profile : Create Leaf Interface Profile
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# description <LINE>
description <LINE>
Description: Update Leaf Interface Group description
Syntax:
Leaf-If-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)216
D Commandsdescription
(config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# description <LINE>
description <LINE>
Description: Update Spine Profile description
Syntax:
Spine-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: spine-profile : Configure Spine Profile
Command Path:
# configure [['terminal', 't']](config)# spine-profile <WORD>(config-spine-profile)# description <LINE>
description <LINE>
Description: Update Spine Group description
Syntax:
Spine-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: spine-group : Configure Spine Group
Command Path:
# configure [['terminal', 't']](config)# spine-profile <WORD>(config-spine-profile)# spine-group <WORD>(config-spine-group)# description <LINE>
description <LINE>
Description: Update Spine Interface Profile description
Syntax:
Spine-If-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: spine-interface-profile : Create Spine Interface Profile
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 217
D Commandsdescription
Command Path:
# configure [['terminal', 't']](config)# spine-interface-profile <WORD>(config-spine-if-profile)# description <LINE>
description <LINE>
Description: Update Spine Interface Group description
Syntax:
Spine-If-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: spine-interface-group : Configure Spine Interface Group
Command Path:
# configure [['terminal', 't']](config)# spine-interface-profile <WORD>(config-spine-if-profile)# spine-interface-group <WORD>(config-spine-if-group)# description <LINE>
description <LINE>
Description: Update Fex Profile description
Syntax:
Fex-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: fex-profile : Configure Fex Profile
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# description <LINE>
description <LINE>
Description: Update Fex Interface Group description
Syntax:
Fex-If-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: fex-interface-group : Configure Fex Interface Group
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)218
D Commandsdescription
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# description <LINE>
description <LINE>
Description: Update Leaf Interface Profile description
Syntax:
Leaf-If-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: leaf-interface-profile : Create Leaf Interface Profile
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-interface-profile <WORD>(config-leaf-if-profile)# description <LINE>
description <LINE>
Description: Update Leaf Interface Group description
Syntax:
Leaf-If-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# description <LINE>
description <LINE>
Description: Update Leaf Profile description
Syntax:
Leaf-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 219
D Commandsdescription
Command Mode: leaf-profile : Configure Leaf Profile
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-profile <WORD>(config-leaf-profile)# description <LINE>
description <LINE>
Description: Update Leaf Group description
Syntax:
Leaf-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: leaf-group : Configure Leaf Group
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# description <LINE>
description <LINE>
Description: Update interface vlan description
Syntax:
interface vlan description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# description <LINE>
description <LINE>
Description: Update Interface description
Syntax:
Interface description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)220
D Commandsdescription
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# description <LINE>
description <LINE>
Description: Update Port-Channel description
Syntax:
Port-Channel description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# description <LINE>
description <LINE>
Description: Update interface vlan description
Syntax:
interface vlan description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# description <LINE>
description <LINE>
Description: Update Interface description
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 221
D Commandsdescription
Interface description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# description <LINE>
description <LINE>
Description: Update Port-Channel description
Syntax:
Port-Channel description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# description <LINE>
description <LINE>
Description: Update Netflow Exporter description
Syntax:
Netflow Exporter description, use single quotes with spaces ex: 'mydescr' (Max Size 128)
LINE
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-exporter)# description <LINE>
description <LINE>
Description: Update Netflow Exporter description
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)222
D Commandsdescription
Syntax:
Netflow Exporter description, use single quotes with spaces ex: 'mydescr' (Max Size 128)
LINE
Command Mode: flow vm-exporter : Configure NetFlow Exporter for VM Networking
Command Path:
# configure [['terminal', 't']](config)# flow vm-exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-vm-exporter)# description <LINE>
description <LINE>
Description: Update Netflow Record description
Syntax:
NetflowRecord description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: flow record : Configure Netflow Record
Command Path:
# configure [['terminal', 't']](config)# flow record <WORD>(config-flow-record)# description <LINE>
description <LINE>
Description: Update Netflow Monitor description
Syntax:
Netflow Monitor description, use single quotes with spaces ex: 'mydescr' (Max Size 128)
LINE
Command Mode: flow monitor : Configure Netflow Monitor
Command Path:
# configure [['terminal', 't']](config)# flow monitor <WORD>(config-flow-monitor)# description <LINE>
description <LINE>
Description: Update Netflow Node-policy description
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 223
D Commandsdescription
Syntax:
NetflowNode-policy description, use single quotes with spaces ex: 'mydescr' (Max Size 128)
LINE
Command Mode: flow node-policy : Configure Netflow Node Policy Parameters
Command Path:
# configure [['terminal', 't']](config)# flow node-policy <WORD>(config-flow-node-pol)# description <LINE>
description <LINE>
Description: Update VPC description
Syntax:
VPC description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# description <LINE>
description <LINE>
Description: Add description to the session
Syntax:
Session description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# description <LINE>
description <LINE>
Description: Add description to the session
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)224
D Commandsdescription
Syntax:
Session description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: monitor fabric : Configue monitor session for fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# description <LINE>
description <LINE>
Description: Add description to the session
Syntax:
Session description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: monitor tenant : Configue monitor session for tenant EPGs
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <WORD>(config-monitor-tenant)# description <LINE>
description <LINE>
Description: Add description to the session
Syntax:
Session description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# description <LINE>
description <STRING>
Description: Configure scheduler description
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 225
D Commandsdescription
Scheduler descriptionSTRING
Command Mode: scheduler : Scheduler configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# description <STRING>
description <WORD>
Description: Add description for this server-group
Syntax:
Description (Max Size 128) surrounded by single quotesWORD
Command Mode: logging : Logging server group configuration mode
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# description <WORD>
description <WORD>
Description: Add zone description
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: zone : Create zone policy
Command Path:
# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>(config-zone)# description <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)226
D Commandsdescription
destination-portdestination-port <port>
Description: Destination port of this analytics server
Syntax:
The analytics server destination port. Number range from=0 to=65535port
Command Mode: flow-exporter : Configure external analytics reachability information
Command Path:
# configure [['terminal', 't']](config)# analytics cluster <WORD>(config-analytics)# flow-exporter <WORD>(config-analytics-cluster-exporter)# destination-port <port>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 227
D Commandsdestination-port
destination-profiledestination-profile
Description: Configure destination profile Parameters
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)228
D Commandsdestination-profile
destinationdestination <WORD>
Description: Configure destination Parameters
Syntax:
The name (Max Size 64)WORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>
destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D>source-ip-prefix <A.B.C.D/M>
Description: Configure monitor remote destination
Syntax:
tenanttenant
tenant name (Max Size 63)tenant_name
applicationapplication
application nameapplication_name
epgepg
epg nameepg_name
destination IPdestination-ip
IP addressA.B.C.D
source IP prefixsource-ip-prefix
IP adddress prefixA.B.C.D/M
Command Mode: monitor fabric : Configue monitor session for fabric interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 229
D Commandsdestination
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>
destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D>source-ip-prefix <A.B.C.D/M>
Description: Configure monitor remote destination
Syntax:
tenanttenant
tenant name (Max Size 63)tenant_name
applicationapplication
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
destination IPdestination-ip
IP addressA.B.C.D
source IP prefixsource-ip-prefix
IP adddress prefixA.B.C.D/M
Command Mode: monitor tenant : Configue monitor session for tenant EPGs
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <WORD>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>
destination <A.B.C.D|A:B::C:D>
Description: Destination IP of analytics server
Syntax:
Destination IP of Analytics ServerA.B.C.D|A:B::C:D
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)230
D Commandsdestination
Command Mode: flow-exporter : Configure external analytics reachability information
Command Path:
# configure [['terminal', 't']](config)# analytics cluster <WORD>(config-analytics)# flow-exporter <WORD>(config-analytics-cluster-exporter)# destination <A.B.C.D|A:B::C:D>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 231
D Commandsdestination
destination addressdestination address <A.B.C.D|A:B::C:D>
Description: Configure destination address
Syntax:
A.B.C.D|A:B::C:DA.B.C.D|A:B::C:D
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transportudp <dstPort>(config-tn-flow-exporter)# destination address <A.B.C.D|A:B::C:D>
destination address <A.B.C.D|A:B::C:D>
Description: Configure destination address
Syntax:
A.B.C.D|A:B::C:DA.B.C.D|A:B::C:D
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-exporter)# destination address <A.B.C.D|A:B::C:D>
destination address <A.B.C.D|A:B::C:D>
Description: Configure destination address
Syntax:
A.B.C.D|A:B::C:DA.B.C.D|A:B::C:D
Command Mode: flow vm-exporter : Configure NetFlow Exporter for VM Networking
Command Path:
# configure [['terminal', 't']](config)# flow vm-exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)232
D Commandsdestination address
<dstPort>(config-flow-vm-exporter)# destination address <A.B.C.D|A:B::C:D>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 233
D Commandsdestination address
destination destipdestination destip <A.B.C.D>
Description: Configure monitor remote destination
Syntax:
Destination IP addressA.B.C.D
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)234
D Commandsdestination destip
destination epgdestination epg tenant <WORD> application <WORD> epg <WORD>
Description: Configure destination EPg
Syntax:
Tenant hosting the EPgtenant
Tenant hosting the EPg (Max Size 63)WORD
Application hosting the EPgapplication
Application hosting the EPg (Max Size 64)WORD
EPgepg
EPg (Max Size 64)WORD
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transportudp <dstPort>(config-tn-flow-exporter)# destination epg tenant <WORD> application <WORD> epg <WORD>
destination epg tenant <WORD> application <WORD> epg <WORD>
Description: Configure destination EPg
Syntax:
Tenant hosting the EPgtenant
Tenant hosting the EPg (Max Size 63)WORD
Application hosting the EPgapplication
Application hosting the EPg (Max Size 64)WORD
EPgepg
EPg (Max Size 64)WORD
Command Mode: flow exporter : Configure Netflow Exporter
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 235
D Commandsdestination epg
Command Path:
# configure [['terminal', 't']](config)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-exporter)# destination epg tenant <WORD> application <WORD> epg <WORD>
destination epg tenant <WORD> application <WORD> epg <WORD>
Description: Configure destination EPg
Syntax:
Tenant hosting the EPgtenant
Tenant hosting the EPg (Max Size 63)WORD
Application hosting the EPgapplication
Application hosting the EPg (Max Size 64)WORD
EPgepg
EPg (Max Size 64)WORD
Command Mode: flow vm-exporter : Configure NetFlow Exporter for VM Networking
Command Path:
# configure [['terminal', 't']](config)# flow vm-exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-vm-exporter)# destination epg tenant <WORD> application <WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)236
D Commandsdestination epg
destination external-l3 epg tenant l3out epgdestination external-l3 epg tenant <WORD> l3out <WORD> epg <WORD>
Description: Epg
Syntax:
Tenanttenant
Tenant hosting the EPg (Max Size 63)WORD
l3Out within the Tenant (Max Size 64)WORD
l3Out within the Tenant (Max Size 64)WORD
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transportudp <dstPort>(config-tn-flow-exporter)# destination external-l3 epg tenant <WORD> l3out <WORD> epg <WORD>
destination external-l3 epg tenant <WORD> l3out <WORD> epg <WORD>
Description: Epg
Syntax:
Tenanttenant
Tenant hosting the EPg (Max Size 63)WORD
l3Out within the Tenant (Max Size 64)WORD
l3Out within the Tenant (Max Size 64)WORD
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-exporter)# destination external-l3 epg tenant <WORD> l3out <WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 237
D Commandsdestination external-l3 epg tenant l3out epg
destination external-l3 epg tenant <WORD> l3out <WORD> epg <WORD>
Description: Epg
Syntax:
Tenanttenant
Tenant hosting the EPg (Max Size 63)WORD
l3Out within the Tenant (Max Size 64)WORD
l3Out within the Tenant (Max Size 64)WORD
Command Mode: flow vm-exporter : Configure NetFlow Exporter for VM Networking
Command Path:
# configure [['terminal', 't']](config)# flow vm-exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-vm-exporter)# destination external-l3 epg tenant <WORD> l3out <WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)238
D Commandsdestination external-l3 epg tenant l3out epg
destination external-l3 epg tenant vrf epgdestination external-l3 epg tenant <WORD> vrf <WORD> epg <WORD>
Description: epg
Syntax:
Tenanttenant
Tenant hosting the EPg (Max Size 63)WORD
Vrf on the Tenant (Max Size 64)WORD
Instp within the Tenant (Max Size 64)WORD
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transportudp <dstPort>(config-tn-flow-exporter)# destination external-l3 epg tenant <WORD> vrf <WORD> epg <WORD>
destination external-l3 epg tenant <WORD> vrf <WORD> epg <WORD>
Description: epg
Syntax:
Tenanttenant
Tenant hosting the EPg (Max Size 63)WORD
Vrf on the Tenant (Max Size 64)WORD
Instp within the Tenant (Max Size 64)WORD
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-exporter)# destination external-l3 epg tenant <WORD> vrf <WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 239
D Commandsdestination external-l3 epg tenant vrf epg
destination external-l3 epg tenant <WORD> vrf <WORD> epg <WORD>
Description: epg
Syntax:
Tenanttenant
Tenant hosting the EPg (Max Size 63)WORD
Vrf on the Tenant (Max Size 64)WORD
Instp within the Tenant (Max Size 64)WORD
Command Mode: flow vm-exporter : Configure NetFlow Exporter for VM Networking
Command Path:
# configure [['terminal', 't']](config)# flow vm-exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-vm-exporter)# destination external-l3 epg tenant <WORD> vrf <WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)240
D Commandsdestination external-l3 epg tenant vrf epg
destination interfacedestination interface ethernet <ethernet> leaf <leaf Id> [mtu <mtu>]
Description: Configure monitor local destination
Syntax:
ethernetethernet
<ethernet><ethernet>
leafleaf
leaf Id<leaf Id>
(Optional) mtu value. Number range from=64 to=9216mtu
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination interface ethernet <ethernet> leaf <leaf Id> [mtu<mtu>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 241
D Commandsdestination interface
destination tenantdestination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D>source-ip-prefix <A.B.C.D/M>
Description: Configure monitor remote destination
Syntax:
tenant name (Max Size 63)tenant_name
applicationapplication
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
destination IPdestination-ip
IP addressA.B.C.D
source IP prefixsource-ip-prefix
IP adddress prefixA.B.C.D/M
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>
destination tenant <WORD> application <WORD> epg <WORD> macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure monitor local destination
Syntax:
tenant name (Max Size 63)WORD
applicationapplication
application name (Max Size 64)WORD
epgepg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)242
D Commandsdestination tenant
epg name (Max Size 64)WORD
macmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination tenant <WORD> application <WORD> epg <WORD> macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 243
D Commandsdestination tenant
dhcp optiondhcp option <WORD> id <NUMBER> [data <WORD>]
Description: Add or modify an existing DHCP option when relayed from the server to the client
Syntax:
Name of the option to add (Max Size 64)WORD
ID of the optionid
ID of the option. Number range from=0 to=255<0-255>
(Optional) Body of the Option TLV as hex string, surrounded by singlequotes ex: 'foo*' (Max Size 256)
WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# dhcp option <WORD> id <NUMBER> [data <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)244
D Commandsdhcp option
dhcp relay policydhcp relay policy tenant|infra <WORD> [option <WORD>]
Description: Associate the BD with a DHCP Relay policy
Syntax:
Select DHCP policies from current Tenanttenant
Select DHCP policy from infrainfra
Name of the DHCP relay policy (Max Size 64)WORD
(Optional) Name of the DHCP option policy (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# dhcp relay policy tenant|infra <WORD> [option <WORD>]
dhcp relay policy tenant|infra <WORD>
Description: Associate the SVIs with a DHCP Relay policy
Syntax:
Select DHCP policies from current Tenanttenant
Select DHCP policy from infrainfra
Name of the DHCP relay policy (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# dhcp relay policy tenant|infra <WORD>
dhcp relay policy tenant|infra <WORD>
Description: Associate the SVIs with a DHCP Relay policy
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 245
D Commandsdhcp relay policy
Select DHCP policies from current Tenanttenant
Select DHCP policy from infrainfra
Name of the DHCP relay policy (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# dhcp relay policy tenant|infra <WORD>
dhcp relay policy tenant|infra <WORD>
Description: Associate the SVIs with a DHCP Relay policy
Syntax:
Select DHCP policies from current Tenanttenant
Select DHCP policy from infrainfra
Name of the DHCP relay policy (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# dhcp relay policy tenant|infra <WORD>
dhcp relay policy tenant|infra <WORD>
Description: Associate the SVIs with a DHCP Relay policy
Syntax:
Select DHCP policies from current Tenanttenant
Select DHCP policy from infrainfra
Name of the DHCP relay policy (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)246
D Commandsdhcp relay policy
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# dhcp relay policy tenant|infra <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 247
D Commandsdhcp relay policy
dhcpv4-serverdhcpv4-server
Description: Config DHCPv4 server in trust control policy
Command Mode: trust-control : Configuration for trust control policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# trust-control <WORD>(config-tenant-fhs-trustctrl)# dhcpv4-server
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)248
D Commandsdhcpv4-server
dhcpv6-serverdhcpv6-server
Description: Config DHCPv6 server in trust control policy
Command Mode: trust-control : Configuration for trust control policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# trust-control <WORD>(config-tenant-fhs-trustctrl)# dhcpv6-server
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 249
D Commandsdhcpv6-server
dhparamdhparam <dhparam>
Description: Set the DH parameter used for HTTPS communication service
Syntax:
DH Param as comma separated values like val1,val2,..valNdhparam
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# dhparam <dhparam>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)250
D Commandsdhparam
directiondirection both|rx|tx
Description:Monitor direction
Syntax:
bothboth
rxrx
txtx
Command Mode: source interface ethernet : Configure monitor for ethernet access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface ethernet <ethernet> leaf <leaf Id>(config-monitor-access-source)# direction both|rx|tx
direction both|rx|tx
Description:Monitor direction
Syntax:
bothboth
rxrx
txtx
Command Mode: source interface port-channel : Configure monitor for port-channel interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface port-channel <port-channel list> leaf <leaf Id>[fex <fex Id>](config-monitor-access-source)# direction both|rx|tx
direction both|rx|tx
Description:Monitor direction
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 251
D Commandsdirection
bothboth
rxrx
txtx
Command Mode: source interface vpc : Configure monitor for VPC interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex<fex Ids>](config-monitor-access-source)# direction both|rx|tx
direction both|rx|tx
Description:Monitor direction
Syntax:
bothboth
rxrx
txtx
Command Mode: source interface ethernet : Configure monitor for ethernet fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>(config-monitor-fabric-source)# direction both|rx|tx
direction both|rx|tx
Description:Monitor direction
Syntax:
bothboth
rxrx
txtx
Command Mode: source application : Configure EPG as monitor source
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)252
D Commandsdirection
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <WORD>(config-monitor-tenant)# source application <application_name> epg <epg_name>(config-monitor-tenant-source)# direction both|rx|tx
direction both|rx|tx
Description: Configure monitor source direction
Syntax:
bothboth
rxrx
txtx
Command Mode: source : Configure monitor virtual source
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# source tenant <WORD> application <WORD> epg <WORD> [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >](config-monitor-virtual-source)# direction both|rx|tx
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 253
D Commandsdirection
disable-connected-checkdisable-connected-check
Description: Disable check for directly connected peer
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# disable-connected-check
disable-connected-check
Description: Disable check for directly connected peer
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# disable-connected-check
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)254
D Commandsdisable-connected-check
disable-peer-as-checkdisable-peer-as-check
Description: Disable checking of peer AS-number while advertising
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# disable-peer-as-check
disable-peer-as-check
Description: Disable checking of peer AS-number while advertising
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# disable-peer-as-check
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 255
D Commandsdisable-peer-as-check
distancedistance <NUMBER>
Description: Set OSPF Policy Preferred Administrative Distance
Syntax:
Distance Value. Number range from=1 to=255<1-255>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# distance <NUMBER>
distance <NUMBER> <NUMBER> <NUMBER>
Description: Configure BGP Address Family Distance Properties
Syntax:
The administrative distance of eBGP routes. Number range from=1to=255
<1-255>
The administrative distance of iBGP routes. Number range from=1to=255
<1-255>
The administrative distance of local routes. Number range from=1to=255
<1-255>
Command Mode: template bgp address-family : Configure Router BGP Address Family Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp address-family <WORD> tenant <WORD>(config-bgp-af)# distance <NUMBER> <NUMBER> <NUMBER>
distance <NUMBER> <NUMBER>
Description: Set EIGRP adminstrative distances
Syntax:
The administrative distance preference for internal routes. Number rangefrom=1 to=255
<1-255>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)256
D Commandsdistance
The administrative distance preference for external routes. Numberrange from=1 to=255
<1-255>
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# distance <NUMBER> <NUMBER>
distance <NUMBER> <NUMBER>
Description: Set EIGRP adminstrative distances
Syntax:
The administrative distance preference for internal routes. Number rangefrom=1 to=255
<1-255>
The administrative distance preference for external routes. Numberrange from=1 to=255
<1-255>
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# distance <NUMBER> <NUMBER>
distance <NUMBER>
Description: Set OSPF Policy Preferred Administrative Distance
Syntax:
Distance Value. Number range from=1 to=255<1-255>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# distance <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 257
D Commandsdistance
distance <NUMBER> <NUMBER> <NUMBER>
Description: Configure BGP Address Family Distance Properties
Syntax:
The administrative distance of eBGP routes. Number range from=1to=255
<1-255>
The administrative distance of iBGP routes. Number range from=1to=255
<1-255>
The administrative distance of local routes. Number range from=1to=255
<1-255>
Command Mode: template bgp address-family : Configure Router BGP Address Family Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bgp address-family <WORD> tenant <WORD>(config-bgp-af)# distance <NUMBER> <NUMBER> <NUMBER>
distance <NUMBER> <NUMBER>
Description: Set EIGRP adminstrative distances
Syntax:
The administrative distance preference for internal routes. Number rangefrom=1 to=255
<1-255>
The administrative distance preference for external routes. Numberrange from=1 to=255
<1-255>
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# distance <NUMBER> <NUMBER>
distance <NUMBER> <NUMBER>
Description: Set EIGRP adminstrative distances
Syntax:
The administrative distance preference for internal routes. Number rangefrom=1 to=255
<1-255>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)258
D Commandsdistance
The administrative distance preference for external routes. Numberrange from=1 to=255
<1-255>
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# distance <NUMBER> <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 259
D Commandsdistance
dnsdns
Description: Configure default dns policy
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# dns
dns label <WORD>
Description: Add a DNS policy to the VRF
Syntax:
Dns policy to applylabel
Dns policy to apply (Max Size 64)WORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# dns label <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)260
D Commandsdns
dnssearchsuffixdnssearchsuffix <suffix>
Description: Add DNS search suffix
Syntax:
suffixsuffix
Command Mode: microsoft : Configure static IP pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# dnssearchsuffix <suffix>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 261
D Commandsdnssearchsuffix
dnsserversdnsservers <DNS server list>
Description: Add dns servers
Syntax:
DNS server listDNS server list
Command Mode: microsoft : Configure static IP pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# dnsservers <DNS server list>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)262
D Commandsdnsservers
dnssuffixdnssuffix <suffix>
Description: Add dns suffix
Syntax:
suffixsuffix
Command Mode: microsoft : Configure static IP pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# dnssuffix <suffix>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 263
D Commandsdnssuffix
dnssvrdnssvr <A.B.C.D>
Description: dnssvr configuration mode
Syntax:
IP Unicast address in format i.i.i.iA.B.C.D
Command Mode: dnssvrgrp : dnssvrgrp configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# dnssvrgrp <WORD>(config-tenant-dnssvrgrp)# dnssvr <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)264
D Commandsdnssvr
dnssvrgrpdnssvrgrp <WORD>
Description: dnssvrgrp configuration mode
Syntax:
Server group name (Max Size 16)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# dnssvrgrp <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 265
D Commandsdnssvrgrp
domaindomain <WORD>
Description: Create the AAA domain to which the user belongs.
Syntax:
Domain for the userWORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# domain <WORD>
domain <WORD> [default]
Description: Configure the domains for dns servers
Syntax:
Domain in the format^([a-zA-Z]|[a-zA-Z][a-zA-Z0-9]|[a-zA-Z][a-zA-Z0-9-.]{0,253}[a-zA-Z0-9])$
WORD
(Optional) Set the default domain for dns serversdefault
Command Mode: dns : Configure default dns policy
Command Path:
# configure [['terminal', 't']](config)# dns(config-dns)# domain <WORD> [default]
domain <WORD>
Description: domain configuration mode
Syntax:
Name of domain (Max Size 512)WORD
Command Mode: dnssvr : dnssvr configuration mode
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)266
D Commandsdomain
(config)# tenant <WORD>(config-tenant)# dnssvrgrp <WORD>(config-tenant-dnssvrgrp)# dnssvr <A.B.C.D>(config-tenant-dnssvrgrp-dnssvr)# domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 267
D Commandsdomain
dot1q-tunneldot1q-tunnel <WORD>
Description: Tunnel configuration mode
Syntax:
Tunnel EPG name (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# dot1q-tunnel <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)268
D Commandsdot1q-tunnel
dscpdscp <0-63>
Description: Configure dscp
Syntax:
Dscp Value<0-63>
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transportudp <dstPort>(config-tn-flow-exporter)# dscp <0-63>
dscp <0-63>
Description: Configure dscp
Syntax:
Dscp Value<0-63>
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-exporter)# dscp <0-63>
dscp <0-63>
Description: Configure dscp
Syntax:
Dscp Value<0-63>
Command Mode: flow vm-exporter : Configure NetFlow Exporter for VM Networking
Command Path:
# configure [['terminal', 't']](config)# flow vm-exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 269
D Commandsdscp
<dstPort>(config-flow-vm-exporter)# dscp <0-63>
dscp <WORD>
Description: Specifies the DSCP value
Syntax:
DSCP valueWORD
Command Mode: flow-exporter : Configure external analytics reachability information
Command Path:
# configure [['terminal', 't']](config)# analytics cluster <WORD>(config-analytics)# flow-exporter <WORD>(config-analytics-cluster-exporter)# dscp <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)270
D Commandsdscp
dsr-vipdsr-vip <WORD>
Description: Configure DSR VIP for a L4-L7 Graph Connector.
Syntax:
Enter VIP address (Max Size None)WORD
Command Mode: connector : Configure Connector for a Service Node
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>] [svcredir <Service Redirection>] [service-type <Service Type>](config-service)# connector <WORD> [cluster-interface <WORD>](config-connector)# dsr-vip <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 271
D Commandsdsr-vip
dsrdsr virtual-ip-address <address> [description <description>]
Description: Add a DSR virtual IP address
Syntax:
Virtual IP address of load balancervirtual-ip-address
IP address<address>
(Optional) descriptiondescription
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# dsr virtual-ip-address <address> [description <description>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)272
D Commandsdsr
E Commands
• ebgp-multihop, page 276
• echo-address, page 277
• echo-mode, page 278
• echo-rx-interval, page 279
• email-addr, page 281
• email-contact, page 282
• email, page 283
• enable-bfd, page 284
• enable-ssl, page 285
• encap-mode, page 286
• encap, page 287
• encryption, page 288
• end, page 289
• endpoint, page 290
• endpoint ip, page 291
• endpoint ip aging, page 292
• endpoint ipv6, page 293
• endpoint loop-detect action bd-learn-disable, page 294
• endpoint loop-detect action port-disable, page 295
• endpoint loop-detect enable, page 296
• endpoint loop-detect factor, page 297
• endpoint loop-detect interval, page 298
• endpoint move-detection, page 299
• endpoint retention bounce-age-interval, page 300
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 273
• endpoint retention hold-interval, page 301
• endpoint retention local-age-interval, page 302
• endpoint retention move-frequency, page 303
• endpoint retention policy, page 304
• endpoint retention remote-age-interval, page 305
• enforce-subnet-learning, page 306
• ep-flush, page 307
• ep-retention-time, page 308
• epg, page 309
• eraseconfig, page 310
• errdisable recovery cause bpduguard, page 311
• errdisable recovery cause ep-move, page 312
• errdisable recovery cause mcp-loop, page 313
• errdisable recovery interval, page 314
• erspan-id, page 315
• erspan-version, page 317
• evpn, page 319
• evpn consumer, page 320
• evpn export, page 321
• evpn import, page 322
• evpn provider, page 323
• exec, page 324
• exit, page 325
• expiration, page 326
• expires, page 327
• export-config, page 328
• export, page 329
• exporter, page 331
• extcommunity-list expanded, page 332
• extcommunity-list standard, page 333
• external-l2, page 334
• external-l3, page 335
• external-l3 epg, page 336
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)274
E Commands
• external-routed-domain, page 337
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 275
E Commands
ebgp-multihopebgp-multihop <NUMBER>
Description: Specify multihop TTL for remote peer
Syntax:
EBGP TTL value. Number range from=1 to=255<1-255>
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# ebgp-multihop <NUMBER>
ebgp-multihop <NUMBER>
Description: Specify multihop TTL for remote peer
Syntax:
EBGP TTL value. Number range from=1 to=255<1-255>
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# ebgp-multihop <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)276
E Commandsebgp-multihop
echo-addressecho-address <arg>
Description: Configure BFD ECHO-SRC-ADDRESS value
Syntax:
arg
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# echo-address <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 277
E Commandsecho-address
echo-modeecho-mode enable
Description: Enable Echo mode
Syntax:
Enable Echo modeenable
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# echo-mode enable
echo-mode enable
Description: Enable Echo mode
Syntax:
Enable Echo modeenable
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# echo-mode enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)278
E Commandsecho-mode
echo-rx-intervalecho-rx-interval <NUMBER>
Description: Configure BFD ECHO-RX-INTERVAL value in milliseconds
Syntax:
BFD interval. Number range from=50 to=999<interval>
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# echo-rx-interval <NUMBER>
echo-rx-interval <NUMBER>
Description: Configure Echo Rx Interval in milliseconds
Syntax:
Echo Rx Interval. Number range from=50 to=999<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# echo-rx-interval <NUMBER>
echo-rx-interval <NUMBER>
Description: Configure Echo Rx Interval in milliseconds
Syntax:
Echo Rx Interval. Number range from=50 to=999<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bfd <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 279
E Commandsecho-rx-interval
(config-template-bfd-pol)# echo-rx-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)280
E Commandsecho-rx-interval
email-addremail-addr <WORD>
Description: Configure the e-mail address
Syntax:
The email address (Max Size None)WORD
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# email-addr <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 281
E Commandsemail-addr
email-contactemail-contact <WORD>
Description: The contact e-mail address
Syntax:
Contract e-mail address (Max Size 512)WORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# email-contact <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)282
E Commandsemail-contact
emailemail <WORD>
Description: Set The email address of the locally-authenticated user.
Syntax:
email address of the locally-authenticated userWORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# email <WORD>
email <WORD>
Description: Set The email address of the organization contact person.
Syntax:
email address (Max Size 40)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# email <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 283
E Commandsemail
enable-bfdenable-bfd
Description: Enable Bidirectional Forwarding Detection(BFD) protocol
Command Mode: template hsrp interface-policy : Configure HSRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template hsrp interface-policy <WORD> tenant <WORD>(config-template-hsrp-if-pol)# enable-bfd
enable-bfd
Description: Enable Bidirectional Forwarding Detection(BFD) protocol
Command Mode: template hsrp interface-policy : Configure HSRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template hsrp interface-policy <WORD> tenant <WORD>(config-template-hsrp-if-pol)# enable-bfd
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)284
E Commandsenable-bfd
enable-sslenable-ssl
Description: Enabling an SSL connection with the LDAP provider
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# enable-ssl
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 285
E Commandsenable-ssl
encap-modeencap-mode auto|vlan|vxlan
Description: Enforce encap mode, domain mode will be used if not set
Syntax:
Uses domain preferenceauto
VLANvlan
VXLANvxlan
Command Mode: vmware-domain : Associate EPG to a VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>][allow-micro-segmentation] [deploy <WORD>] [push <WORD>] [delimiter <WORD>](config-tenant-app-epg-domain)# encap-mode auto|vlan|vxlan
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)286
E Commandsencap-mode
encapencap scope <arg>
Description: Configure the encap scope
Syntax:
The encap scopescope
arg
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# encap scope <>
encap scope <arg>
Description: Configure the encap scope
Syntax:
The encap scopescope
arg
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# encap scope <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 287
E Commandsencap
encryptionencryption
Description: Enable AES Encryption
Command Mode: crypto aes : AES encryption configuration
Command Path:
# configure [['terminal', 't']](config)# crypto aes(config-aes)# encryption
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)288
E Commandsencryption
endend
Description: Exit to the exec mode
Command Mode: exec : Exec Mode
Command Path:
# end
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 289
E Commandsend
endpointendpoint retention <WORD>
Description: Specify an endpoint retention policy for this VRF
Syntax:
Specify an endpoint retention policy for this VRFretention
Endpoint Retention Policy (Max Size 64)WORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# endpoint retention <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)290
E Commandsendpoint
endpoint ipendpoint ip <A.B.C.D/LEN> next-hop <A.B.C.D> [scope <scope>]
Description: IP endpoint
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
Next-Hop for endpointnext-hop
IP address in format i.i.i.iA.B.C.D
(Optional) Scope of the address among ['shared', 'public', 'private']scope
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# endpoint ip <A.B.C.D/LEN> next-hop <A.B.C.D> [scope <scope>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 291
E Commandsendpoint ip
endpoint ip agingendpoint ip aging
Description: Enable/Disable Endpoint IP Aging
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# endpoint ip aging
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)292
E Commandsendpoint ip aging
endpoint ipv6endpoint ipv6 <A:B::C:D/LEN> next-hop <A:B::C:D> [scope <scope>]
Description: IPv6 endpoint
Syntax:
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
Next-Hop for endpointnext-hop
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
(Optional) Scope of the address among ['shared', 'public', 'private']scope
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# endpoint ipv6 <A:B::C:D/LEN> next-hop <A:B::C:D> [scope <scope>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 293
E Commandsendpoint ipv6
endpoint loop-detect action bd-learn-disableendpoint loop-detect action bd-learn-disable
Description: Configure Endpoint Loop Protection Action to BD-Learn-Disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# endpoint loop-detect action bd-learn-disable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)294
E Commandsendpoint loop-detect action bd-learn-disable
endpoint loop-detect action port-disableendpoint loop-detect action port-disable
Description: Configure Endpoint Loop Protection Action to Port-Disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# endpoint loop-detect action port-disable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 295
E Commandsendpoint loop-detect action port-disable
endpoint loop-detect enableendpoint loop-detect enable
Description: Enable/Disable Endpoint Loop-Detect Policy
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# endpoint loop-detect enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)296
E Commandsendpoint loop-detect enable
endpoint loop-detect factorendpoint loop-detect factor <NUMBER>
Description: Configure Endpoint Loop Detection Factor
Syntax:
End Point Loop ProtectionMultipication Factor. Number range from=1to=255
<1-255>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# endpoint loop-detect factor <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 297
E Commandsendpoint loop-detect factor
endpoint loop-detect intervalendpoint loop-detect interval <NUMBER>
Description: Configure Endpoint Loop Detection Interval
Syntax:
End Point Loop Detection Interval. Number range from=30 to=300<30-300>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# endpoint loop-detect interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)298
E Commandsendpoint loop-detect interval
endpoint move-detectionendpoint move-detection <WORD>
Description: Endpoint Move detection Mode
Syntax:
Endpoint Move detection ModeWORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint move-detection <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 299
E Commandsendpoint move-detection
endpoint retention bounce-age-intervalendpoint retention bounce-age-interval x in <0-0> or <150-65535>
Description: Set the bounce age interval for endpoints
Syntax:
Set the Bounce Age Interval, use 0 for infinitex in <0-0> or <150-65535>
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention bounce-age-interval x in <0-0> or <150-65535>
endpoint retention bounce-age-interval x in <0-0> or <150-65535>
Description: Set the bounce age interval for endpoints
Syntax:
Set the Bounce Age Interval, use 0 for infinitex in <0-0> or <150-65535>
Command Mode: template endpoint retention policy : Configure an endpoint retention policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention bounce-age-interval x in<0-0> or <150-65535>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)300
E Commandsendpoint retention bounce-age-interval
endpoint retention hold-intervalendpoint retention hold-interval <NUMBER>
Description: Set the hold interval for endpoints
Syntax:
Set the Hold Interval. Number range from=5 to=65535<5-65535>
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention hold-interval <NUMBER>
endpoint retention hold-interval <NUMBER>
Description: Set the hold interval for endpoints
Syntax:
Set the Hold Interval. Number range from=5 to=65535<5-65535>
Command Mode: template endpoint retention policy : Configure an endpoint retention policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention hold-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 301
E Commandsendpoint retention hold-interval
endpoint retention local-age-intervalendpoint retention local-age-interval x in <0-0> or <120-65535>
Description: Set the local endpoint age interval
Syntax:
Set the local endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention local-age-interval x in <0-0> or <120-65535>
endpoint retention local-age-interval x in <0-0> or <120-65535>
Description: Set the local endpoint age interval
Syntax:
Set the local endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>
Command Mode: template endpoint retention policy : Configure an endpoint retention policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention local-age-interval x in<0-0> or <120-65535>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)302
E Commandsendpoint retention local-age-interval
endpoint retention move-frequencyendpoint retention move-frequency <NUMBER>
Description: Set the move frequency
Syntax:
Set the move frequency. Number range from=0 to=65535<0-65535>
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention move-frequency <NUMBER>
endpoint retention move-frequency <NUMBER>
Description: Set the move frequency
Syntax:
Set the move frequency. Number range from=0 to=65535<0-65535>
Command Mode: template endpoint retention policy : Configure an endpoint retention policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention move-frequency <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 303
E Commandsendpoint retention move-frequency
endpoint retention policyendpoint retention policy <WORD>
Description: Associate the BD with an endpoint retention policy
Syntax:
Name of the endpoint retention policy to set (Max Size 64)WORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)304
E Commandsendpoint retention policy
endpoint retention remote-age-intervalendpoint retention remote-age-interval x in <0-0> or <120-65535>
Description: Set the remote endpoint age interval
Syntax:
Remote endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention remote-age-interval x in <0-0> or <120-65535>
endpoint retention remote-age-interval x in <0-0> or <120-65535>
Description: Set the remote endpoint age interval
Syntax:
Remote endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>
Command Mode: template endpoint retention policy : Configure an endpoint retention policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention remote-age-interval x in<0-0> or <120-65535>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 305
E Commandsendpoint retention remote-age-interval
enforce-subnet-learningenforce-subnet-learning
Description: Subnet learning enforcement
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# enforce-subnet-learning
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)306
E Commandsenforce-subnet-learning
ep-flushep-flush
Description: Clear remote L2 entries when local vPC L2 entries are cleared
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# ep-flush
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 307
E Commandsep-flush
ep-retention-timeep-retention-time <WORD>
Description: Retention Time for all End Points in this domain
Syntax:
End Point Retention TimeWORD
Command Mode: vmware-domain : Create a VMM VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# ep-retention-time <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)308
E Commandsep-retention-time
epgepg <WORD> [type <WORD>]
Description: AEPg configuration mode
Syntax:
Application EPG name (Max Size 64)WORD
(Optional) Specify EPG typeWORD
Command Mode: application : application configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>]
epg <WORD>
Description: AEPg configuration mode
Syntax:
Application EPG name (Max Size 64)WORD
Command Mode: application : application configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# dnssvrgrp <WORD>(config-tenant-dnssvrgrp)# application <WORD>(config-tenant-dnssvrgrp-app)# epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 309
E Commandsepg
eraseconfigeraseconfig [setup]
Description: Erase config and reboot
Syntax:
(Optional) Clean setupsetup
Command Mode: exec : Exec Mode
Command Path:
# eraseconfig [setup]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)310
E Commandseraseconfig
errdisable recovery cause bpduguarderrdisable recovery cause bpduguard
Description: Enable timer to recover from BPDU Guard error disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# errdisable recovery cause bpduguard
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 311
E Commandserrdisable recovery cause bpduguard
errdisable recovery cause ep-moveerrdisable recovery cause ep-move
Description: Enable timer to recover from End Point Move error disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# errdisable recovery cause ep-move
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)312
E Commandserrdisable recovery cause ep-move
errdisable recovery cause mcp-looperrdisable recovery cause mcp-loop
Description: Enable timer to recover from MCP Loop error disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# errdisable recovery cause mcp-loop
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 313
E Commandserrdisable recovery cause mcp-loop
errdisable recovery intervalerrdisable recovery interval <NUMBER>
Description: Configure Error Disable Recovery Interval
Syntax:
Timer-interval (sec). Number range from=30 to=65535<30-65535>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# errdisable recovery interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)314
E Commandserrdisable recovery interval
erspan-iderspan-id <id>
Description: Erspan Id
Syntax:
erspan Id. Number range from=1 to=1023id
Command Mode: destination tenant : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# erspan-id <id>
erspan-id <id>
Description: Erspan Id
Syntax:
erspan Id. Number range from=1 to=1023id
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# erspan-id <id>
erspan-id <arg>
Description: Erspan Id
Syntax:
erspan Id. Number range from=1 to=1023arg
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 315
E Commandserspan-id
(config)# monitor tenant <tenant_name> session <WORD>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-tenant-dest)# erspan-id <>
erspan-id <arg>
Description: Configure ERSPAN ID
Syntax:
ERSPAN ID. Number range from=1 to=1023arg
Command Mode: destination destip : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# erspan-id <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)316
E Commandserspan-id
erspan-versionerspan-version <version> [enforce]
Description: Set ERSPAN version
Syntax:
ERSPAN versionversion
(Optional) enforceenforce
Command Mode: destination tenant : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# erspan-version <version> [enforce]
erspan-version <version> [enforce]
Description: Set ERSPAN version
Syntax:
ERSPAN versionversion
(Optional) enforceenforce
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# erspan-version <version> [enforce]
erspan-version <version> [enforce]
Description: Set ERSPAN version
Syntax:
ERSPAN versionversion
(Optional) enforceenforce
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 317
E Commandserspan-version
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <WORD>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-tenant-dest)# erspan-version <version> [enforce]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)318
E Commandserspan-version
evpnevpn route-reflector spine <LIST>
Description: Configure BGP evpn route-reflectors
Syntax:
Configure BGP evpn route-reflectorsroute-reflector
Configure Spines as route-reflectorsspine
Route-reflector spine node name or ID list. Ex. spine1 or 103,105LIST
Command Mode: bgp-fabric : Border Gateway Protocol (BGP)
Command Path:
# configure [['terminal', 't']](config)# bgp-fabric(config-bgp-fabric)# evpn route-reflector spine <LIST>
evpn route-reflector spine <LIST>
Description: Configure BGP evpn route-reflectors
Syntax:
Configure BGP evpn route-reflectorsroute-reflector
Configure Spines as route-reflectorsspine
Route-reflector spine node name or ID list. Ex. spine1 or 103,105LIST
Command Mode: bgp : Border Gateway Protocol (BGP)
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# bgp fabric(config-pod-bgp)# evpn route-reflector spine <LIST>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 319
E Commandsevpn
evpn consumerevpn consumer <WORD>
Description: EVPN Consumer
Syntax:
Label NameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# evpn consumer <WORD>
evpn consumer <WORD>
Description: EVPN Consumer
Syntax:
Label NameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# evpn consumer <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)320
E Commandsevpn consumer
evpn exportevpn export map <WORD> label <WORD>
Description: VRF export
Syntax:
Route-map based VRF exportmap
Route Map Name (Max Size 63)WORD
Configure consumer labellabel
Consumer label nameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# evpn export map <WORD> label <WORD>
evpn export map <WORD> label <WORD>
Description: VRF export
Syntax:
Route-map based VRF exportmap
Route Map Name (Max Size 63)WORD
Configure consumer labellabel
Consumer label nameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# evpn export map <WORD> label <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 321
E Commandsevpn export
evpn importevpn import map <WORD> label <WORD>
Description: VRF import
Syntax:
Route-map based VRF importmap
Route Map Name (Max Size 63)WORD
Configure consumer labellabel
Consumer label nameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# evpn import map <WORD> label <WORD>
evpn import map <WORD> label <WORD>
Description: VRF import
Syntax:
Route-map based VRF importmap
Route Map Name (Max Size 63)WORD
Configure consumer labellabel
Consumer label nameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# evpn import map <WORD> label <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)322
E Commandsevpn import
evpn providerevpn provider <WORD>
Description: EVPN Provider
Syntax:
Provide Label NameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# evpn provider <WORD>
evpn provider <WORD>
Description: EVPN Provider
Syntax:
Provide Label NameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# evpn provider <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 323
E Commandsevpn provider
execexec
Description: Exec Mode
Command Mode: None
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)324
E Commandsexec
exitexit
Description: Exit from current mode
Command Mode: exec : Exec Mode
Command Path:
# exit
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 325
E Commandsexit
expirationexpiration <DATE>
Description: If expires enabled, Set expiration date of locally-authenticated user account.
Syntax:
UTC Date format (YYYY-MM-DDTHH:MM:SS.mmm[+-]hh:mm)DATE
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# expiration <DATE>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)326
E Commandsexpiration
expiresexpires
Description: Enable expiry for locally-authenticated user account
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# expires
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 327
E Commandsexpires
export-configexport-config <WORD>
Description: Export Configuration
Syntax:
Filename(absolute path)WORD
Command Mode: exec : Exec Mode
Command Path:
# export-config <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)328
E Commandsexport-config
exportexport to tenant <WORD> [as <WORD>]
Description: Export a contract to another tenant
Syntax:
Tenant to export the command toto
Tenant to export the command totenant
Tenant to export the command to (Max Size 63)WORD
(Optional) New name under which the contract will be known (MaxSize 64)
WORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# export to tenant <WORD> [as <WORD>]
export map <WORD>
Description: VRF export
Syntax:
Route-map for inter VRF route leakmap
Route Map Name (Max Size 63)WORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# export map <WORD>
export map <WORD>
Description: VRF export
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 329
E Commandsexport
Route-map for inter VRF route leakmap
Route Map Name (Max Size 63)WORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# export map <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)330
E Commandsexport
exporterexporter <WORD>
Description: Assign Netflow Exporter to the Monitor
Syntax:
Exporter Name (Max Size 64)WORD
Command Mode: flow monitor : Configure Netflow Monitor
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow monitor <WORD>(config-tn-flow-monitor)# exporter <WORD>
exporter <WORD>
Description: Assign Netflow Exporter to the Monitor
Syntax:
Exporter Name (Max Size 64)WORD
Command Mode: flow monitor : Configure Netflow Monitor
Command Path:
# configure [['terminal', 't']](config)# flow monitor <WORD>(config-flow-monitor)# exporter <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 331
E Commandsexporter
extcommunity-list expandedextcommunity-list expanded <WORD> <LINE>
Description: Configure expanded community list templates
Syntax:
Community list name (Max Size 64)WORD
Regular-expressionLINE
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route group <WORD> tenant <WORD>(config-route-group)# extcommunity-list expanded <WORD> <LINE>
extcommunity-list expanded <WORD> <LINE>
Description: Configure expanded community list templates
Syntax:
Community list name (Max Size 64)WORD
Regular-expressionLINE
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route group <WORD> tenant <WORD>(config-route-group)# extcommunity-list expanded <WORD> <LINE>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)332
E Commandsextcommunity-list expanded
extcommunity-list standardextcommunity-list standard <WORD> [scope <scope>] ASN2:NN
Description: Configure standard community list templates
Syntax:
Community list name (Max Size 64)WORD
(Optional) transitive or non-transitivescope
Community number aa:nn formatASN2:NN
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route group <WORD> tenant <WORD>(config-route-group)# extcommunity-list standard <WORD> [scope <scope>] ASN2:NN
extcommunity-list standard <WORD> [scope <scope>] ASN2:NN
Description: Configure standard community list templates
Syntax:
Community list name (Max Size 64)WORD
(Optional) transitive or non-transitivescope
Community number aa:nn formatASN2:NN
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route group <WORD> tenant <WORD>(config-route-group)# extcommunity-list standard <WORD> [scope <scope>] ASN2:NN
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 333
E Commandsextcommunity-list standard
external-l2external-l2 epg <WORD>
Description: L2 external EPG creation/configuration
Syntax:
L2 external EPG nameepg
L2 external EPG name (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)334
E Commandsexternal-l2
external-l3external-l3 epg <WORD> <WORD>
Description: External L3 EPG to associate
Syntax:
Specify the external EPGepg
External L3 EPG nameWORD
evpn label nameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# external-l3 epg <WORD> <WORD>
external-l3 epg <WORD> <WORD>
Description: External L3 EPG to associate
Syntax:
Specify the external EPGepg
External L3 EPG nameWORD
evpn label nameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# external-l3 epg <WORD> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 335
E Commandsexternal-l3
external-l3 epgexternal-l3 epg <WORD> [oob-mgmt] [l3out <l3out>]
Description: External L3 EPG configuration mode
Syntax:
External L3 EPG name (Max Size 49)WORD
(Optional) External L3 EPG for Out of bandoob-mgmt
(Optional) Configure external-l3 epg on an API configured L3Outl3out
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)336
E Commandsexternal-l3 epg
external-routed-domainexternal-routed-domain <l3dom>
Description: Add l3Dom to the Resource Pool
Syntax:
l3doml3dom
Command Mode: l4l7 resource-pool : Configure L4-L7 Service Resource Pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 resource-pool <WORD>(config-resource-pool)# external-routed-domain <l3dom>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 337
E Commandsexternal-routed-domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)338
E Commandsexternal-routed-domain
F Commands
• fabric-external, page 341
• fabric-interface ethernet, page 342
• fabric-internal, page 343
• fabric clear, page 344
• fabric show, page 345
• fail-auth-epg, page 346
• fail-auth-vlan, page 347
• fc, page 348
• fcoe, page 349
• fcoe fcmap, page 351
• fcoe fka-adv-period, page 352
• fcoe vsan vlan loadbalancing, page 353
• fctimer e-d-tov, page 355
• fctimer r-a-tov, page 356
• feature, page 358
• fex-interface-group, page 359
• fex-profile, page 360
• fex, page 361
• file, page 363
• filter, page 364
• filter tenant bd, page 366
• filter tenant vrf, page 367
• fips mode, page 368
• firewall-logging, page 369
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 339
• firewall, page 370
• firmware-version, page 371
• firmware, page 372
• firmware repository add, page 373
• firmware repository delete, page 374
• firmware upgrade controller-group, page 375
• firmware upgrade switch-group, page 376
• first-file, page 377
• first-hop-security, page 378
• first-hop-security security-policy, page 379
• first-hop-security trust-control, page 380
• first-name, page 381
• flow-exporter, page 382
• flow direction, page 383
• flow exporter, page 384
• flow monitor, page 386
• flow node-policy, page 388
• flow record, page 390
• flow timeout collection, page 391
• flow timeout template, page 392
• flow vm-exporter, page 393
• force-pwd-change, page 394
• forged-transmits, page 395
• format, page 396
• forward-error-correction, page 397
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)340
F Commands
fabric-externalfabric-external <NUMBER>
Description: Intrasite/Intersite Connectivity Profile
Syntax:
Fabric ID. Number range from=0 to=9223372036854775807<ID>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# fabric-external <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 341
F Commandsfabric-external
fabric-interface ethernetfabric-interface ethernet
Description: Ethernet IEEE 802.3z
Syntax:
interface rangearg
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# fabric-interface ethernet
fabric-interface ethernet
Description: Ethernet IEEE 802.3z
Syntax:
interface rangearg
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# fabric-interface ethernet
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)342
F Commandsfabric-interface ethernet
fabric-internalfabric-internal
Description: Fabric Policy Configuration for internal ports
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# fabric-internal
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 343
F Commandsfabric-internal
fabric clearfabric <nodes> clear <scope>
Description: Clear switch information
Syntax:
node list<nodes>
switch command<scope>
Command Mode: exec : Exec Mode
Command Path:
# fabric <nodes> clear <scope>
Usage Notes:
When clearing virtual fibre channel (VFC) interface counters using the fabric node clearcounters interfacevfc slot/port command, allow up to eight seconds after sending the command for the counters to clear.
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)344
F Commandsfabric clear
fabric showfabric <nodes> show <scope>
Description: Show switch information
Syntax:
node list<nodes>
switch command<scope>
Command Mode: exec : Exec Mode
Command Path:
# fabric <nodes> show <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 345
F Commandsfabric show
fail-auth-epgfail-auth-epg tenant <arg> application <arg> epg <arg>
Description: Set default EPg name if authentication fails
Syntax:
Tenant hosting the EPgtenant
arg
Application Nameapplication
arg
Deploy EPg if authentication failsepg
arg
Command Mode: policy-map type port-authentication : Create node level port authentication policy
Command Path:
# configure [['terminal', 't']](config)# policy-map type port-authentication <WORD>(config-pmap-port-authentication)# fail-auth-epg tenant <> application <> epg <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)346
F Commandsfail-auth-epg
fail-auth-vlanfail-auth-vlan <vlan-id>
Description: Set default vlan encap if authentication fails
Syntax:
Configure Vlan ID<vlan-id>
Command Mode: policy-map type port-authentication : Create node level port authentication policy
Command Path:
# configure [['terminal', 't']](config)# policy-map type port-authentication <WORD>(config-pmap-port-authentication)# fail-auth-vlan <vlan-id>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 347
F Commandsfail-auth-vlan
fcfc
Description: Enable fc BD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# fc
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)348
F Commandsfc
fcoefcoe vsan <NUMBER> vlan <NUMBER>
Description: Configure fcoe parameters
Syntax:
Configure Vsan IDvsan
Configure Vsan ID. Number range from=1 to=4093<vsan-id>
Configure Vlan IDvlan
Configure Vlan ID. Number range from=1 to=4094<vlan-id>
Command Mode: vsan-domain : Configure vsan domain
Command Path:
# configure [['terminal', 't']](config)# vsan-domain <name>(config-vsan)# fcoe vsan <NUMBER> vlan <NUMBER>
fcoe fcmap <WORD>
Description: Configure fcoe parameters
Syntax:
FC Mapfcmap
Configure FC Map, range is from 0E:FC:00 to 0E:FC:FFWORD
Command Mode: template fc-fabric-policy : Configure FC Fabric Policy(Max Size 64)
Command Path:
# configure [['terminal', 't']](config)# template fc-fabric-policy <WORD>(config-fc-fabric-policy)# fcoe fcmap <WORD>
fcoe vsan <NUMBER> vlan <NUMBER>
Description: Configure fcoe parameters
Syntax:
Configure Vsan IDvsan
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 349
F Commandsfcoe
Configure Vsan ID. Number range from=1 to=4093<vsan-id>
Configure Vlan IDvlan
Configure Vlan ID. Number range from=1 to=4094<vlan-id>
Command Mode: template vsan-attribute : Configure Vsan Attributes(Max Size 64)
Command Path:
# configure [['terminal', 't']](config)# template vsan-attribute <WORD>(config-vsan-attr)# fcoe vsan <NUMBER> vlan <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)350
F Commandsfcoe
fcoe fcmapfcoe fcmap <WORD>
Description: Configure FC Map
Syntax:
Configure FC Map, range is from 0E:FC:00 to 0E:FC:FFWORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# fcoe fcmap <WORD>
fcoe fcmap <WORD>
Description: Configure FC Map
Syntax:
Configure FC Map, range is from 0E:FC:00 to 0E:FC:FFWORD
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# fcoe fcmap <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 351
F Commandsfcoe fcmap
fcoe fka-adv-periodfcoe fka-adv-period <NUMBER>
Description: Configure FIP Keep Alive Interval
Syntax:
FIP Keep Alive Timer. Number range from=4 to=60<interval>
Command Mode: template fc-leaf-policy : Configure FC Leaf Policy(Max Size 64)
Command Path:
# configure [['terminal', 't']](config)# template fc-leaf-policy <WORD>(config-fc-leaf-policy)# fcoe fka-adv-period <NUMBER>
fcoe fka-adv-period <NUMBER>
Description: Configure FIP Keep Alive Interval
Syntax:
FIP Keep Alive Timer. Number range from=4 to=60<interval>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# fcoe fka-adv-period <NUMBER>
fcoe fka-adv-period <NUMBER>
Description: Configure FIP Keep Alive Interval
Syntax:
FIP Keep Alive Timer. Number range from=4 to=60<interval>
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# fcoe fka-adv-period <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)352
F Commandsfcoe fka-adv-period
fcoe vsan vlan loadbalancingfcoe vsan <NUMBER> vlan <NUMBER> loadbalancing src-dst-id|src-dst-ox-id
Description: Configure loadbalancing
Syntax:
Configure Vsan IDvsan
Configure Vsan ID. Number range from=1 to=4093<vsan-id>
Configure Vlan IDvlan
Configure Vlan ID. Number range from=1 to=4094<vlan-id>
Load balaning based on src-dst-idsrc-dst-id
Load balaning based on the src-dst-ox-idsrc-dst-ox-id
Command Mode: vsan-domain : Configure vsan domain
Command Path:
# configure [['terminal', 't']](config)# vsan-domain <name>(config-vsan)# fcoe vsan <NUMBER> vlan <NUMBER> loadbalancing src-dst-id|src-dst-ox-id
fcoe vsan <NUMBER> vlan <NUMBER> loadbalancing src-dst-id|src-dst-ox-id
Description: Configure loadbalancing
Syntax:
Configure Vsan IDvsan
Configure Vsan ID. Number range from=1 to=4093<vsan-id>
Configure Vlan IDvlan
Configure Vlan ID. Number range from=1 to=4094<vlan-id>
Load balaning based on src-dst-idsrc-dst-id
Load balaning based on the src-dst-ox-idsrc-dst-ox-id
Command Mode: template vsan-attribute : Configure Vsan Attributes(Max Size 64)
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 353
F Commandsfcoe vsan vlan loadbalancing
Command Path:
# configure [['terminal', 't']](config)# template vsan-attribute <WORD>(config-vsan-attr)# fcoe vsan <NUMBER> vlan <NUMBER> loadbalancing src-dst-id|src-dst-ox-id
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)354
F Commandsfcoe vsan vlan loadbalancing
fctimer e-d-tovfctimer e-d-tov <NUMBER>
Description: Configure e_d_tov value
Syntax:
FC Fabric error detect timeout. Number range from=1000 to=4000<interval>
Command Mode: template fc-fabric-policy : Configure FC Fabric Policy(Max Size 64)
Command Path:
# configure [['terminal', 't']](config)# template fc-fabric-policy <WORD>(config-fc-fabric-policy)# fctimer e-d-tov <NUMBER>
fctimer e-d-tov <NUMBER>
Description: Configure e_d_tov value
Syntax:
FC Fabric error detect timeout. Number range from=1000 to=4000<interval>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# fctimer e-d-tov <NUMBER>
fctimer e-d-tov <NUMBER>
Description: Configure e_d_tov value
Syntax:
FC Fabric error detect timeout. Number range from=1000 to=4000<interval>
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# fctimer e-d-tov <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 355
F Commandsfctimer e-d-tov
fctimer r-a-tovfctimer r-a-tov <NUMBER>
Description: Configure r_a_tov value
Syntax:
FC Fabric resolution allocation timeout. Number range from=5000to=10000
<interval>
Command Mode: template fc-fabric-policy : Configure FC Fabric Policy(Max Size 64)
Command Path:
# configure [['terminal', 't']](config)# template fc-fabric-policy <WORD>(config-fc-fabric-policy)# fctimer r-a-tov <NUMBER>
fctimer r-a-tov <NUMBER>
Description: Configure r_a_tov value
Syntax:
FC Fabric resolution allocation timeout. Number range from=5000to=10000
<interval>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# fctimer r-a-tov <NUMBER>
fctimer r-a-tov <NUMBER>
Description: Configure r_a_tov value
Syntax:
FC Fabric resolution allocation timeout. Number range from=5000to=10000
<interval>
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)356
F Commandsfctimer r-a-tov
(config)# spine <101-4000>(config-spine)# fctimer r-a-tov <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 357
F Commandsfctimer r-a-tov
featurefeature analytics|netflow
Description: Select Netflow
Syntax:
Select Analyticsanalytics
Select Netflownetflow
Command Mode: node-control : Create a Node Control Policy
Command Path:
# configure [['terminal', 't']](config)# node-control policy <WORD>(config-node)# feature analytics|netflow
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)358
F Commandsfeature
fex-interface-groupfex-interface-group <WORD>
Description: Configure Fex Interface Group
Syntax:
Fex Interface Group Name (Max Size 64)WORD
Command Mode: fex-profile : Configure Fex Profile
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 359
F Commandsfex-interface-group
fex-profilefex-profile <WORD>
Description: Configure Fex Profile
Syntax:
Fex Profile Name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)360
F Commandsfex-profile
fexfex associate <NUMBER> template <WORD>
Description: Configure Fex on the Interface
Syntax:
Associate the port to a FEXassociate
Fex Number. Number range from=101 to=199NUMBER
Associate a templatetemplate
Fex Template Name (Max Size 64)WORD
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# fex associate <NUMBER> template <WORD>
fex associate <arg>
Description: Configure Fex on the Interface
Syntax:
Associate the port to a FEXassociate
Fex Number. Number range from=101 to=199arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# fex associate <>
fex associate <arg>
Description: Configure Fex on the Interface
Syntax:
Associate the port to a FEXassociate
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 361
F Commandsfex
Fex Number. Number range from=101 to=199arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# fex associate <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)362
F Commandsfex
filefile <FILENAME>
Description: Snapshot file name
Syntax:
Snapshot file nameFILENAME
Command Mode: snapshot download : Configuration snapshot download setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot download <WORD>(config-download)# file <FILENAME>
file <FILENAME>
Description: Snapshot file name
Syntax:
Snapshot file nameFILENAME
Command Mode: snapshot import : Configuration import setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# file <FILENAME>
file <FILENAME>
Description: Snapshot file name
Syntax:
Snapshot file nameFILENAME
Command Mode: snapshot upload : Configuration snapshot upload setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot upload <WORD>(config-upload)# file <FILENAME>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 363
F Commandsfile
filterfilter <WORD>
Description: Set the LDAP filter to be used in a user search
Syntax:
filter used in user search (Max Size 63)<WORD>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# filter <WORD>
filter tenant <tenant_name> application <application_name> epg <epg_name>
Description: EPG filter
Syntax:
tenanttenant
tenant name (Max Size 63)tenant_name
applicationapplication
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
Command Mode: source interface ethernet : Configure monitor for ethernet access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface ethernet <ethernet> leaf <leaf Id>(config-monitor-access-source)# filter tenant <tenant_name> application <application_name>epg <epg_name>
filter tenant <tenant_name> application <application_name> epg <epg_name>
Description: EPG filter
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)364
F Commandsfilter
tenanttenant
tenant name (Max Size 63)tenant_name
applicationapplication
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
Command Mode: source interface port-channel : Configure monitor for port-channel interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface port-channel <port-channel list> leaf <leaf Id>[fex <fex Id>](config-monitor-access-source)# filter tenant <tenant_name> application <application_name>epg <epg_name>
filter tenant <tenant_name> application <application_name> epg <epg_name>
Description: EPG filter
Syntax:
tenanttenant
tenant name (Max Size 63)tenant_name
applicationapplication
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
Command Mode: source interface vpc : Configure monitor for VPC interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex<fex Ids>](config-monitor-access-source)# filter tenant <tenant_name> application <application_name>epg <epg_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 365
F Commandsfilter
filter tenant bdfilter tenant <tenant_name> bd <bd_name>
Description: BD filter
Syntax:
tenanttenant
tenant nametenant_name
BD namebd_name
Command Mode: source interface ethernet : Configure monitor for ethernet fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>(config-monitor-fabric-source)# filter tenant <tenant_name> bd <bd_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)366
F Commandsfilter tenant bd
filter tenant vrffilter tenant <tenant_name> vrf <vrf_name>
Description: VRF filter
Syntax:
tenanttenant
tenant nametenant_name
vrf namevrf_name
Command Mode: source interface ethernet : Configure monitor for ethernet fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>(config-monitor-fabric-source)# filter tenant <tenant_name> vrf <vrf_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 367
F Commandsfilter tenant vrf
fips modefips mode enable
Description: Enable FIPS mode
Syntax:
Enable FIPS modeenable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# fips mode enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)368
F Commandsfips mode
firewall-loggingfirewall-logging server-group <WORD> [severity severity <severity-info>] [polling-interval <polling-interval>][action-type <action-type>]
Description: Configure firewall-logging on AVS
Syntax:
Specify server group nameserver-group
Logging server-group name (Max Size 64)WORD
(Optional) Specify severity infoseverity <severity-info>
(Optional) Specify polling interval time in seconds. Number rangefrom=60 to=86400
polling-interval
(Optional) Specify action typeaction-type
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# firewall-logging server-group <WORD> [severity severity <severity-info>][polling-interval <polling-interval>] [action-type <action-type>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 369
F Commandsfirewall-logging
firewallfirewall mode enabled|disabled|learning
Description: Configure firewall mode on AVS
Syntax:
firewall modemode
Enabled modeenabled
Disabled modedisabled
Learning modelearning
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# firewall mode enabled|disabled|learning
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)370
F Commandsfirewall
firmware-versionfirmware-version <version>
Description: Set target firmware version
Syntax:
firmware version<version>
Command Mode: controller-group : Controller Upgrade Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# controller-group(config-firmware-controller)# firmware-version <version>
firmware-version <version>
Description: Set target firmware version
Syntax:
firmware version<version>
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# firmware-version <version>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 371
F Commandsfirmware-version
firmwarefirmware
Description: Firmware upgrade configuration Mode
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# firmware
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)372
F Commandsfirmware
firmware repository addfirmware repository add <WORD>
Description: Add firmware image to repository
Syntax:
Firmware image filename(absolute path)WORD
Command Mode: exec : Exec Mode
Command Path:
# firmware repository add <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 373
F Commandsfirmware repository add
firmware repository deletefirmware repository delete <WORD>
Description: Remove firmware image from repository
Syntax:
Firmware image nameWORD
Command Mode: exec : Exec Mode
Command Path:
# firmware repository delete <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)374
F Commandsfirmware repository delete
firmware upgrade controller-groupfirmware upgrade controller-group
Description: Trigger controller-group upgrade
Command Mode: exec : Exec Mode
Command Path:
# firmware upgrade controller-group
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 375
F Commandsfirmware upgrade controller-group
firmware upgrade switch-groupfirmware upgrade switch-group <WORD>
Description: Trigger switch-group upgrade
Syntax:
switch-group name (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# firmware upgrade switch-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)376
F Commandsfirmware upgrade switch-group
first-filefirst-file <FILENAME>
Description: First snapshot file name
Syntax:
First snapshot file nameFILENAME
Command Mode: snapshot rollback : Configuration rollback setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot rollback <WORD>(config-rollback)# first-file <FILENAME>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 377
F Commandsfirst-file
first-hop-securityfirst-hop-security
Description: Configuration for first hop security
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)378
F Commandsfirst-hop-security
first-hop-security security-policyfirst-hop-security security-policy <WORD>
Description: Associate the bridge domain with a first hop security policy
Syntax:
first hop security policy name to be associated (Max Size 64)WORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# first-hop-security security-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 379
F Commandsfirst-hop-security security-policy
first-hop-security trust-controlfirst-hop-security trust-control <WORD>
Description: Bind the EPG to a trust control policy
Syntax:
trust control to associate (Max Size 64)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# first-hop-security trust-control <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)380
F Commandsfirst-hop-security trust-control
first-namefirst-name <WORD>
Description: Set the first name of the locally-authenticated user.
Syntax:
first name (Max Size 32)WORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# first-name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 381
F Commandsfirst-name
flow-exporterflow-exporter <WORD>
Description: Configure external analytics reachability information
Syntax:
Analytics config server nameWORD
Command Mode: analytics : Configure external analytics reachability information
Command Path:
# configure [['terminal', 't']](config)# analytics cluster <WORD>(config-analytics)# flow-exporter <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)382
F Commandsflow-exporter
flow directionflow direction ingress|egress|both
Description: Configure Netflow Direction (Valid only for AVS domain)
Syntax:
Ingress Directioningress
Egress Directionegress
Bidirectionalboth
Command Mode: vmware-domain : Associate EPG to a VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>][allow-micro-segmentation] [deploy <WORD>] [push <WORD>] [delimiter <WORD>](config-tenant-app-epg-domain)# flow direction ingress|egress|both
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 383
F Commandsflow direction
flow exporterflow exporter <WORD>
Description: Configure NetFlow Exporter Policy
Syntax:
VMM Exporter Policy NameWORD
Command Mode: configure-dvs : Configure a VMWare Domain as DVS type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-dvs(config-vmware-dvs)# flow exporter <WORD>
flow exporter <WORD>
Description: Configure NetFlow Exporter Policy
Syntax:
VMM Exporter Policy NameWORD
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# flow exporter <WORD>
flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp <dstPort>
Description: Configure Netflow Exporter
Syntax:
Exporter Name (Max Size 64)WORD
Configure destination addressdestination
Configure destination addressaddress
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
Configure Transport Porttransport
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)384
F Commandsflow exporter
Configure Transport Portudp
Configure Transport PortdstPort
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transportudp <dstPort>
flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp <dstPort>
Description: Configure Netflow Exporter
Syntax:
Exporter Name (Max Size 64)WORD
Configure destination addressdestination
Configure destination addressaddress
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
Configure Transport Porttransport
Configure Transport Portudp
Configure Transport PortdstPort
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 385
F Commandsflow exporter
flow monitorflow monitor enable
Description: Configure Netflow Monitor
Syntax:
Enable Netflow Monitorenable
Command Mode: vmware-domain : Associate EPG to a VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>][allow-micro-segmentation] [deploy <WORD>] [push <WORD>] [delimiter <WORD>](config-tenant-app-epg-domain)# flow monitor enable
flow monitor <WORD>
Description: Configure Netflow Monitor
Syntax:
Monitor Name (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow monitor <WORD>
flow monitor <WORD>
Description: Configure Netflow Monitor
Syntax:
Monitor Name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)386
F Commandsflow monitor
(config)# flow monitor <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 387
F Commandsflow monitor
flow node-policyflow node-policy <WORD>
Description: Netflow Node Policy Configuration
Syntax:
Netflow Node Policy Name (Max Size 64)WORD
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# flow node-policy <WORD>
flow node-policy <WORD>
Description: Node-policy name
Syntax:
Netflow Node Policy Name (Max Size 64)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# flow node-policy <WORD>
flow node-policy <WORD>
Description: Node-policy name
Syntax:
Netflow Node Policy Name (Max Size 64)WORD
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# flow node-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)388
F Commandsflow node-policy
flow node-policy <WORD>
Description: Configure Netflow Node Policy Parameters
Syntax:
Netflow Node Policy Name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# flow node-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 389
F Commandsflow node-policy
flow recordflow record <WORD>
Description: Configure Netflow Record
Syntax:
Record Name (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow record <WORD>
flow record <WORD>
Description: Configure Netflow Record
Syntax:
Exporter Name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# flow record <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)390
F Commandsflow record
flow timeout collectionflow timeout collection <arg>
Description: Collection time interval
Syntax:
Configure collection timeout value in seconds. Number range from=60to=36000
arg
Command Mode: flow node-policy : Configure Netflow Node Policy Parameters
Command Path:
# configure [['terminal', 't']](config)# flow node-policy <WORD>(config-flow-node-pol)# flow timeout collection <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 391
F Commandsflow timeout collection
flow timeout templateflow timeout template <arg>
Description: Template time interval
Syntax:
Configure template timeout value in seconds. Number range from=60to=64000
arg
Command Mode: flow node-policy : Configure Netflow Node Policy Parameters
Command Path:
# configure [['terminal', 't']](config)# flow node-policy <WORD>(config-flow-node-pol)# flow timeout template <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)392
F Commandsflow timeout template
flow vm-exporterflow vm-exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp <dstPort>
Description: Configure NetFlow Exporter for VM Networking
Syntax:
NetFlow Exporter Name (Max Size 64)WORD
Configure destination addressdestination
Configure destination addressaddress
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
Configure Transport Porttransport
Configure Transport Portudp
Configure Transport PortdstPort
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# flow vm-exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 393
F Commandsflow vm-exporter
force-pwd-changeforce-pwd-change
Description: Force the user to change password in next login
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# force-pwd-change
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)394
F Commandsforce-pwd-change
forged-transmitsforged-transmits accept
Description: Enable/disable forged transmits on trunk
Syntax:
enableaccept
Command Mode: trunk-portgroup : Configure a trunk port group in the VMWare domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# trunk-portgroup <>(config-vmware-trunk)# forged-transmits accept
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 395
F Commandsforged-transmits
formatformat xml|short-txt|aml
Description: Configure the format of the message
Syntax:
Xmlxml
Short-txtshort-txt
Amlaml
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# format xml|short-txt|aml
format xml|json
Description: Snapshot format: xml or json
Syntax:
XML formatxml
JSON formatjson
Command Mode: snapshot export : Configuration export setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot export <WORD>(config-export)# format xml|json
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)396
F Commandsformat
forward-error-correctionforward-error-correction <WORD>
Description: Forward Error Correction
Syntax:
Forward Error Correction ModeWORD
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# forward-error-correction <WORD>
forward-error-correction <WORD>
Description: Forward Error Correction
Syntax:
Forward Error Correction ModeWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# forward-error-correction <WORD>
forward-error-correction <WORD>
Description: Forward Error Correction
Syntax:
Forward Error Correction ModeWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 397
F Commandsforward-error-correction
(config-leaf-if)# forward-error-correction <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)398
F Commandsforward-error-correction
G Commands
• global-name, page 400
• graceful-restart-helper, page 401
• graceful-restart, page 402
• group, page 404
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 399
global-nameglobal-name <WORD>
Description: Set private network global name
Syntax:
Private network global name (Max Size 64)WORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# global-name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)400
G Commandsglobal-name
graceful-restart-helpergraceful-restart-helper
Description: Configure BGP Policy Graceful Restart Helper
Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# graceful-restart-helper
graceful-restart-helper
Description: Configure BGP Policy Graceful Restart Helper
Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# graceful-restart-helper
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 401
G Commandsgraceful-restart-helper
graceful-restartgraceful-restart helper-disable
Description: Disable OSPF Policy Graceful Restart Helper
Syntax:
disable Restart helperhelper-disable
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# graceful-restart helper-disable
graceful-restart stalepath-time <NUMBER>
Description: Set BGP Policy Graceful Restart Timers
Syntax:
Maximum time that BGP keeps stale routes from the restarting BGPpeer
stalepath-time
Timer Value in Seconds. Number range from=1 to=3600<1-3600>
Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# graceful-restart stalepath-time <NUMBER>
graceful-restart helper-disable
Description: Disable OSPF Policy Graceful Restart Helper
Syntax:
disable Restart helperhelper-disable
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)402
G Commandsgraceful-restart
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# graceful-restart helper-disable
graceful-restart stalepath-time <NUMBER>
Description: Set BGP Policy Graceful Restart Timers
Syntax:
Maximum time that BGP keeps stale routes from the restarting BGPpeer
stalepath-time
Timer Value in Seconds. Number range from=1 to=3600<1-3600>
Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# graceful-restart stalepath-time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 403
G Commandsgraceful-restart
groupgroup <WORD>
Description: Specify server groups
Syntax:
Server group name (Max Size 127)<WORD>
Command Mode: aaa authentication login console : Configure console methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login console(config-console)# group <WORD>
group <WORD>
Description: Specify server groups
Syntax:
Server group name (Max Size 127)<WORD>
Command Mode: aaa authentication login default : Configure default methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login default(config-default)# group <WORD>
group <WORD>
Description: Set provider group for login domain
Syntax:
Server group name (Max Size 127)<WORD>
Command Mode: aaa authentication login domain : Configure domain methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login domain <WORD>(config-domain)# group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)404
G Commandsgroup
H Commands
• hello-interval, page 406
• host-mode, page 407
• host-rt-leak, page 408
• hsrp delay, page 409
• hsrp enable-bfd, page 410
• hsrp group, page 411
• hsrp use-bia, page 412
• hsrp version, page 413
• http, page 414
• https, page 415
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 405
hello-intervalhello-interval <NUMBER>
Description: Hello interval
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# hello-interval <NUMBER>
hello-interval <NUMBER>
Description: Hello interval
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# hello-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)406
H Commandshello-interval
host-modehost-mode <arg>
Description: Set host mode
Syntax:
Host modearg
Command Mode: switchport port-authentication : Port authentication configuration
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# switchport port-authentication <WORD>(config-port-authentication)# host-mode <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 407
H Commandshost-mode
host-rt-leakhost-rt-leak enable
Description: Configure BGP Host Type2 Routes
Syntax:
Enabling the host routes type 2 Policyenable
Command Mode: template bgp address-family : Configure Router BGP Address Family Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp address-family <WORD> tenant <WORD>(config-bgp-af)# host-rt-leak enable
host-rt-leak enable
Description: Configure BGP Host Type2 Routes
Syntax:
Enabling the host routes type 2 Policyenable
Command Mode: template bgp address-family : Configure Router BGP Address Family Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bgp address-family <WORD> tenant <WORD>(config-bgp-af)# host-rt-leak enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)408
H Commandshost-rt-leak
hsrp delayhsrp delay minimum|reload <NUMBER>
Description: HSRP initialization delay
Syntax:
Minimum delayminimum
Delay after reloadreload
Delay in seconds. Number range from=0 to=10000<0-10000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp delay minimum|reload <NUMBER>
hsrp delay minimum|reload <NUMBER>
Description: HSRP initialization delay
Syntax:
Minimum delayminimum
Delay after reloadreload
Delay in seconds. Number range from=0 to=10000<0-10000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp delay minimum|reload <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 409
H Commandshsrp delay
hsrp enable-bfdhsrp enable-bfd
Description: Enable Bidirectional Forwarding Detection(BFD) protocol
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp enable-bfd
hsrp enable-bfd
Description: Enable Bidirectional Forwarding Detection(BFD) protocol
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp enable-bfd
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)410
H Commandshsrp enable-bfd
hsrp grouphsrp group <NUMBER> [['ipv4', 'ipv6']]
Description: Configure HSRP Group
Syntax:
Group number(0-255 for v1, 0-4095 for v2). Number range from=0to=4095
<0-4095>
(Optional) Configure IP Version 4 groupipv4
(Optional) Configure IP Version 6 groupipv6
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']]
hsrp group <NUMBER> [['ipv4', 'ipv6']]
Description: Configure HSRP Group
Syntax:
Group number(0-255 for v1, 0-4095 for v2). Number range from=0to=4095
<0-4095>
(Optional) Configure IP Version 4 groupipv4
(Optional) Configure IP Version 6 groupipv6
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 411
H Commandshsrp group
hsrp use-biahsrp use-bia
Description: HSRP uses interfaces burned in address
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp use-bia
hsrp use-bia
Description: HSRP uses interfaces burned in address
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp use-bia
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)412
H Commandshsrp use-bia
hsrp versionhsrp version 1|2
Description: Configure Hsrp Version
Syntax:
Version 11
Version 22
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp version 1|2
hsrp version 1|2
Description: Configure Hsrp Version
Syntax:
Version 11
Version 22
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp version 1|2
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 413
H Commandshsrp version
httphttp
Description: HTTP communication policy group
Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)414
H Commandshttp
httpshttps
Description: HTTPS communication policy group
Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 415
H Commandshttps
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)416
H Commandshttps
I Commands
• idle-flow-timeout, page 424
• immediacy-immediate, page 425
• import-config, page 426
• inband-mgmt, page 427
• inband-mgmt epg, page 428
• inherit-from-epg, page 429
• inherit, page 431
• inherit analytics-policy, page 438
• inherit bfd, page 439
• inherit bgp, page 440
• inherit bgp address-family, page 441
• inherit bgp dampening, page 442
• inherit eigrp, page 443
• inherit fc-fabric-policy, page 445
• inherit fc-leaf-policy, page 446
• inherit hsrp, page 447
• inherit ipv4, page 448
• inherit ipv6, page 449
• inherit isis-fabric, page 452
• inherit node-control-policy, page 453
• inherit node-only, page 454
• inherit ntp-fabric, page 455
• inherit pod-group, page 456
• inherit snmp-fabric, page 457
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 417
• inherit vsan-attribute, page 458
• instance, page 459
• interface, page 460
• interface ethernet, page 463
• interface inband-mgmt0, page 465
• interface mgmt0, page 466
• interface port-channel, page 467
• interface vfc-po, page 469
• interface vfc, page 470
• interface vlan, page 471
• interface vpc, page 472
• interpod, page 473
• ip-inspection-admin-status, page 474
• ip, page 475
• ip address-range, page 478
• ip address, page 480
• ip address tenant application, page 484
• ip address tenant external-l2, page 486
• ip address tenant external-l3, page 488
• ip bandwidth, page 490
• ip bfd, page 493
• ip dhcp relay address tenant application, page 496
• ip dhcp relay address tenant external-l2, page 499
• ip dhcp relay address tenant external-l3, page 500
• ip distribute-list eigrp, page 501
• ip dscp, page 503
• ip flow, page 505
• ip hello-interval, page 509
• ip hold-interval, page 512
• ip igmp, page 515
• ip igmp allow-v3-asm, page 516
• ip igmp fast-leave, page 518
• ip igmp group-timeout, page 520
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)418
I Commands
• ip igmp inherit, page 522
• ip igmp last-member-query-count, page 524
• ip igmp last-member-query-response-time, page 526
• ip igmp querier-timeout, page 527
• ip igmp query-interval, page 529
• ip igmp query-max-response-time, page 531
• ip igmp report-link-local-groups, page 533
• ip igmp report-policy, page 535
• ip igmp robustness-variable, page 537
• ip igmp snooping, page 539
• ip igmp snooping access-group route-map leaf interface ethernet ethernet vlan, page 540
• ip igmp snooping access-group route-map leaf interface port-channel vlan, page 541
• ip igmp snooping access-group route-map vpc context interface vpc vlan, page 542
• ip igmp snooping fast-leave, page 543
• ip igmp snooping last-member-query-interval, page 544
• ip igmp snooping policy, page 545
• ip igmp snooping querier, page 546
• ip igmp snooping query-interval, page 547
• ip igmp snooping query-max-response-time, page 548
• ip igmp snooping startup-query-count, page 549
• ip igmp snooping startup-query-interval, page 550
• ip igmp snooping static-group leaf interface ethernet ethernet vlan, page 551
• ip igmp snooping static-group leaf interface port-channel vlan, page 552
• ip igmp snooping static-group vpc context interface vpc vlan, page 553
• ip igmp ssm-translate, page 554
• ip igmp startup-query-count, page 555
• ip igmp startup-query-interval, page 557
• ip igmp state-limit, page 559
• ip igmp state-limit reserved, page 561
• ip igmp static-oif, page 563
• ip igmp version, page 565
• ip multicast, page 567
• ip next-hop-self, page 568
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 419
I Commands
• ip ospf authentication-key, page 571
• ip ospf authentication, page 573
• ip ospf bfd, page 575
• ip ospf cost, page 577
• ip ospf dead-interval, page 579
• ip ospf hello-interval, page 581
• ip ospf inherit, page 583
• ip ospf mtu-ignore, page 585
• ip ospf network, page 586
• ip ospf passive-interface, page 588
• ip ospf prefix-suppression, page 589
• ip ospf priority, page 591
• ip ospf retransmit-interval, page 593
• ip ospf transmit-delay, page 595
• ip passive-interface, page 597
• ip pim, page 600
• ip pim auto-rp forward, page 601
• ip pim auto-rp listen, page 602
• ip pim auto-rp mapping-agent-policy, page 603
• ip pim border, page 604
• ip pim bsr bsr-policy, page 605
• ip pim bsr forward, page 606
• ip pim bsr listen, page 607
• ip pim dr-delay, page 608
• ip pim dr-priority, page 610
• ip pim fast-convergence, page 612
• ip pim hello-authentication, page 613
• ip pim hello-interval, page 615
• ip pim inherit, page 617
• ip pim jp-interval, page 618
• ip pim jp-policy, page 620
• ip pim mtu, page 622
• ip pim neighbor-policy, page 623
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)420
I Commands
• ip pim passive, page 625
• ip pim register-rate-limit, page 626
• ip pim register-source, page 627
• ip pim rp-address, page 628
• ip pim sg-expiry-timer, page 629
• ip pim sparse, page 630
• ip pim ssm route-map, page 631
• ip pim state-limit, page 632
• ip pim state-limit reserved, page 633
• ip pim strict-rfc-compliant, page 634
• ip pim use-shared-tree-only, page 636
• ip prefix-list, page 637
• ip prefix-list permit le, page 638
• ip prefix, page 639
• ip prefix permit le, page 640
• ip router eigrp, page 641
• ip router ospf default, page 643
• ip shared address consumer, page 645
• ip shared address provider, page 646
• ip split-horizon, page 647
• ip summary-address eigrp, page 650
• ip throughput-delay, page 652
• ip ttl, page 655
• ipobtainmode, page 657
• iprange, page 658
• ipv6-router, page 659
• ipv6, page 660
• ipv6 address-range, page 662
• ipv6 address, page 664
• ipv6 address tenant application, page 668
• ipv6 address tenant external-l2, page 670
• ipv6 address tenant external-l3, page 672
• ipv6 bandwidth, page 674
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 421
I Commands
• ipv6 bfd, page 676
• ipv6 dhcp relay address tenant application, page 678
• ipv6 dhcp relay address tenant external-l2, page 679
• ipv6 dhcp relay address tenant external-l3, page 680
• ipv6 distribute-list eigrp, page 681
• ipv6 flow, page 683
• ipv6 hello-interval, page 687
• ipv6 hold-interval, page 689
• ipv6 link-local, page 691
• ipv6 nd hop-limit, page 693
• ipv6 nd managed-config-flag, page 696
• ipv6 nd mtu, page 698
• ipv6 nd ns-interval, page 701
• ipv6 nd ns-retries, page 704
• ipv6 nd other-config-flag, page 707
• ipv6 nd policy, page 709
• ipv6 nd prefix, page 710
• ipv6 nd ra-interval, page 712
• ipv6 nd ra-lifetime, page 715
• ipv6 nd reachable-time, page 718
• ipv6 nd retrans-timer, page 721
• ipv6 nd suppress-ra-mtu, page 724
• ipv6 nd suppress-ra, page 726
• ipv6 next-hop-self, page 728
• ipv6 ospf bfd, page 730
• ipv6 ospf cost, page 732
• ipv6 ospf dead-interval, page 734
• ipv6 ospf hello-interval, page 736
• ipv6 ospf inherit, page 738
• ipv6 ospf mtu-ignore, page 740
• ipv6 ospf network, page 741
• ipv6 ospf passive-interface, page 743
• ipv6 ospf prefix-suppression, page 744
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)422
I Commands
• ipv6 ospf priority, page 746
• ipv6 ospf retransmit-interval, page 748
• ipv6 ospf transmit-delay, page 750
• ipv6 passive-interface, page 752
• ipv6 router eigrp, page 754
• ipv6 router ospf default, page 756
• ipv6 shared address consumer, page 758
• ipv6 shared address provider, page 759
• ipv6 split-horizon, page 760
• ipv6 summary-address eigrp, page 762
• ipv6 throughput-delay, page 764
• isis, page 766
• isolation, page 767
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 423
I Commands
idle-flow-timeoutidle-flow-timeout <idleFlowTimeout>
Description: Configure Idle Flow TimeOut
Syntax:
Configure Idle Flow TimeOut. Number range from=10 to=600idleFlowTimeout
Command Mode: flow exporter : Configure NetFlow Exporter Policy
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-dvs(config-vmware-dvs)# flow exporter <WORD>(config-vmware-dvs-flow-exporter)# idle-flow-timeout <idleFlowTimeout>
idle-flow-timeout <idleFlowTimeout>
Description: Configure Idle Flow TimeOut
Syntax:
Configure Idle Flow TimeOut. Number range from=10 to=600idleFlowTimeout
Command Mode: flow exporter : Configure NetFlow Exporter Policy
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# flow exporter <WORD>(config-vmware-avs-flow-exporter)# idle-flow-timeout <idleFlowTimeout>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)424
I Commandsidle-flow-timeout
immediacy-immediateimmediacy-immediate enable
Description: Enable/disable immediate immediacy on trunk
Syntax:
enableenable
Command Mode: trunk-portgroup : Configure a trunk port group in the VMWare domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# trunk-portgroup <>(config-vmware-trunk)# immediacy-immediate enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 425
I Commandsimmediacy-immediate
import-configimport-config <WORD>
Description: Import Configuration
Syntax:
Filename(absolute path)WORD
Command Mode: exec : Exec Mode
Command Path:
# import-config <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)426
I Commandsimport-config
inband-mgmtinband-mgmt epg <WORD>
Description: Enter Inside In-band management mode to modify inband properties or create new inband
Syntax:
inband mgmt epg label, usage inband-mgmt epgepg
epg name for inband epg, it can be existing inband epg or new oneWORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 427
I Commandsinband-mgmt
inband-mgmt epginband-mgmt epg <WORD>
Description: Associate node to a Inband EPG
Syntax:
Inband End Point Group Name (Max Size 64)WORD
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# inband-mgmt epg <WORD>
inband-mgmt epg <WORD>
Description: Associate node to a Inband EPG
Syntax:
Inband End Point Group Name (Max Size 64)WORD
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# inband-mgmt epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)428
I Commandsinband-mgmt epg
inherit-from-epginherit-from-epg application <WORD> epg <WORD>
Description: EPG settings inheritance
Syntax:
Application for the EPG where to inherit settingsapplication
Application for the EPG where to inherit settings (Max Size 64)WORD
EPG where to inherit settingsepg
EPG where to inherit settings (Max Size 64)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# inherit-from-epg application <WORD> epg <WORD>
inherit-from-epg epg <WORD>
Description: EPG settings inheritance
Syntax:
EPG where to inherit settingsepg
EPG where to inherit settings (Max Size 64)WORD
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# inherit-from-epg epg <WORD>
inherit-from-epg epg <WORD>
Description: EPG settings inheritance
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 429
I Commandsinherit-from-epg
EPG where to inherit settingsepg
EPG where to inherit settings (Max Size 64)WORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# inherit-from-epg epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)430
I Commandsinherit-from-epg
inheritinherit route-profile <WORD> <WORD>
Description: Inherit a policy template
Syntax:
Configure route-profileroute-profile
Route profile nameWORD
route control context nameWORD
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# inherit route-profile <WORD> <WORD>
inherit route-profile <WORD> <WORD>
Description: Inherit a policy template
Syntax:
Configure route-profileroute-profile
Route profile nameWORD
route control context nameWORD
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# inherit route-profile <WORD> <WORD>
inherit route-profile <WORD> <WORD>
Description: Inherit a policy template
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 431
I Commandsinherit
Syntax:
Configure route-profileroute-profile
Route profile nameWORD
route control context nameWORD
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# inherit route-profile <WORD> <WORD>
inherit route-profile <WORD> <WORD>
Description: Inherit a policy template
Syntax:
Configure route-profileroute-profile
Route profile nameWORD
route control context nameWORD
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# inherit route-profile <WORD> <WORD>
inherit route-profile <WORD> <WORD>
Description: Inherit a policy template
Syntax:
Configure route-profileroute-profile
Route profile nameWORD
route control context nameWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)432
I Commandsinherit
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# inherit route-profile <WORD> <WORD>
inherit route tag <WORD>
Description: Inherit a policy template
Syntax:
Policy template for routesroute
Route tag policy templatetag
Policy template name (Max Size 64)WORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# inherit route tag <WORD>
inherit group-policy <WORD>
Description: Inherit HSRP Group template policy
Syntax:
Associate the Group with an HSRP Group policygroup-policy
Policy nameWORD
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# inherit group-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 433
I Commandsinherit
inherit eigrp vrf-policy <WORD>
Description: Inherit EIGRP VRF Policy under this VRF
Syntax:
Inherit EIGRP VRF Policyeigrp
Inherit EIGRP VRF Policyvrf-policy
Policy nameWORD
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# inherit eigrp vrf-policy <WORD>
inherit route-profile <WORD> <WORD>
Description: Inherit a policy template
Syntax:
Configure route-profileroute-profile
Route profile nameWORD
route control context nameWORD
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# inherit route-profile <WORD> <WORD>
inherit route-profile <WORD> <WORD>
Description: Inherit a policy template
Syntax:
Configure route-profileroute-profile
Route profile nameWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)434
I Commandsinherit
route control context nameWORD
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# inherit route-profile <WORD> <WORD>
inherit route-profile <WORD> <WORD>
Description: Inherit a policy template
Syntax:
Configure route-profileroute-profile
Route profile nameWORD
route control context nameWORD
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# inherit route-profile <WORD> <WORD>
inherit route-profile <WORD> <WORD>
Description: Inherit a policy template
Syntax:
Configure route-profileroute-profile
Route profile nameWORD
route control context nameWORD
Command Mode: match prefix-list : Match entries of a prefix-list
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 435
I Commandsinherit
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# inherit route-profile <WORD> <WORD>
inherit route-profile <WORD> <WORD>
Description: Inherit a policy template
Syntax:
Configure route-profileroute-profile
Route profile nameWORD
route control context nameWORD
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# inherit route-profile <WORD> <WORD>
inherit route tag <WORD>
Description: Inherit a policy template
Syntax:
Policy template for routesroute
Route tag policy templatetag
Policy template name (Max Size 64)WORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# inherit route tag <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)436
I Commandsinherit
inherit group-policy <WORD>
Description: Inherit HSRP Group template policy
Syntax:
Associate the Group with an HSRP Group policygroup-policy
Policy nameWORD
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# inherit group-policy <WORD>
inherit eigrp vrf-policy <WORD>
Description: Inherit EIGRP VRF Policy under this VRF
Syntax:
Inherit EIGRP VRF Policyeigrp
Inherit EIGRP VRF Policyvrf-policy
Policy nameWORD
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# inherit eigrp vrf-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 437
I Commandsinherit
inherit analytics-policyinherit analytics-policy cluster <WORD> server <WORD>
Description: Associate an analytics policy
Syntax:
Analyics Clustercluster
Name of analytics clusterWORD
Analyics Serverserver
Name of analytics policyWORD
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# template leaf-policy-group <WORD>(config-leaf-policy-group)# inherit analytics-policy cluster <WORD> server <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)438
I Commandsinherit analytics-policy
inherit bfdinherit bfd ip|ipv6 <WORD>
Description: BFD Policy
Syntax:
IPv4 Addressip
IPv6 Addressipv6
BFD PolicyWORD
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# inherit bfd ip|ipv6 <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 439
I Commandsinherit bfd
inherit bgpinherit bgp timer <WORD>
Description: Inherit VRF specific BGP Timer Policy
Syntax:
Inherit BGP Timer Policytimer
BGP Template Policy Name (Max Size 64)WORD
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# inherit bgp timer <WORD>
inherit bgp timer <WORD>
Description: Inherit VRF specific BGP Timer Policy
Syntax:
Inherit BGP Timer Policytimer
BGP Template Policy Name (Max Size 64)WORD
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# inherit bgp timer <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)440
I Commandsinherit bgp
inherit bgp address-familyinherit bgp address-family <WORD>
Description: Inherit BGP Address Family Policy
Syntax:
BGP Address Family Policy Name (Max Size 64)WORD
Command Mode: address-family : Configure an address-family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-af)# inherit bgp address-family <WORD>
inherit bgp address-family <WORD>
Description: Inherit BGP Address Family Policy
Syntax:
BGP Address Family Policy Name (Max Size 64)WORD
Command Mode: address-family : Configure an address-family
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-af)# inherit bgp address-family <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 441
I Commandsinherit bgp address-family
inherit bgp dampeninginherit bgp dampening <WORD>
Description: Inherit Route Profile with BGP Dampening Policy
Syntax:
Route Profile with BGP Dampening Policy Name (Max Size 64)WORD
Command Mode: address-family : Configure an address-family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-af)# inherit bgp dampening <WORD>
inherit bgp dampening <WORD>
Description: Inherit Route Profile with BGP Dampening Policy
Syntax:
Route Profile with BGP Dampening Policy Name (Max Size 64)WORD
Command Mode: address-family : Configure an address-family
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-af)# inherit bgp dampening <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)442
I Commandsinherit bgp dampening
inherit eigrpinherit eigrp ip|ipv6 interface-policy <WORD>
Description: Inherit EIGRP interface template policy
Syntax:
Address Family IPv4ip
Address Family IPv6ipv6
Associate the interface with an EIGRP interface policyinterface-policy
Policy nameWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# inherit eigrp ip|ipv6 interface-policy <WORD>
inherit eigrp ip|ipv6 interface-policy <WORD>
Description: Inherit EIGRP interface template policy
Syntax:
Address Family IPv4ip
Address Family IPv6ipv6
Associate the interface with an EIGRP interface policyinterface-policy
Policy nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# inherit eigrp ip|ipv6 interface-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 443
I Commandsinherit eigrp
inherit eigrp ip|ipv6 interface-policy <WORD>
Description: Inherit EIGRP interface template policy
Syntax:
Address Family IPv4ip
Address Family IPv6ipv6
Associate the interface with an EIGRP interface policyinterface-policy
Policy nameWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# inherit eigrp ip|ipv6 interface-policy <WORD>
inherit eigrp ip|ipv6 interface-policy <WORD>
Description: Inherit EIGRP interface template policy
Syntax:
Address Family IPv4ip
Address Family IPv6ipv6
Associate the interface with an EIGRP interface policyinterface-policy
Policy nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# inherit eigrp ip|ipv6 interface-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)444
I Commandsinherit eigrp
inherit fc-fabric-policyinherit fc-fabric-policy <WORD>
Description: FC Fabric Policy
Syntax:
FC Fabric PolicyWORD
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# inherit fc-fabric-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 445
I Commandsinherit fc-fabric-policy
inherit fc-leaf-policyinherit fc-leaf-policy <WORD>
Description: FC Leaf Policy
Syntax:
FC Leaf PolicyWORD
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# inherit fc-leaf-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)446
I Commandsinherit fc-leaf-policy
inherit hsrpinherit hsrp interface-policy <WORD>
Description: Inherit HSRP interface template policy
Syntax:
Associate the interface with an HSRP interface policyinterface-policy
Policy nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# inherit hsrp interface-policy <WORD>
inherit hsrp interface-policy <WORD>
Description: Inherit HSRP interface template policy
Syntax:
Associate the interface with an HSRP interface policyinterface-policy
Policy nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# inherit hsrp interface-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 447
I Commandsinherit hsrp
inherit ipv4inherit ipv4 ospf vrf-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF Policyospf
Inherit OSPF vrf-policyvrf-policy
OSPF Template Policy name (Max Size 64)WORD
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# inherit ipv4 ospf vrf-policy <WORD>
inherit ipv4 ospf vrf-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF Policyospf
Inherit OSPF vrf-policyvrf-policy
OSPF Template Policy name (Max Size 64)WORD
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# inherit ipv4 ospf vrf-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)448
I Commandsinherit ipv4
inherit ipv6inherit ipv6 nd <WORD>
Description: Inherit IPv6 Neighbor Discovery template policy
Syntax:
Associate the interface with an IPv6 Neighbor Discovery policynd
Policy nameWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# inherit ipv6 nd <WORD>
inherit ipv6 nd <WORD>
Description: Inherit IPv6 Neighbor Discovery template policy
Syntax:
Associate the interface with an IPv6 Neighbor Discovery policynd
Policy nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# inherit ipv6 nd <WORD>
inherit ipv6 ospf vrf-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF Policyospf
Inherit OSPF vrf-policyvrf-policy
OSPF Template Policy name (Max Size 64)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 449
I Commandsinherit ipv6
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# inherit ipv6 ospf vrf-policy <WORD>
inherit ipv6 nd <WORD>
Description: Inherit IPv6 Neighbor Discovery template policy
Syntax:
Associate the interface with an IPv6 Neighbor Discovery policynd
Policy nameWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# inherit ipv6 nd <WORD>
inherit ipv6 nd <WORD>
Description: Inherit IPv6 Neighbor Discovery template policy
Syntax:
Associate the interface with an IPv6 Neighbor Discovery policynd
Policy nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# inherit ipv6 nd <WORD>
inherit ipv6 ospf vrf-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)450
I Commandsinherit ipv6
Inherit OSPF Policyospf
Inherit OSPF vrf-policyvrf-policy
OSPF Template Policy name (Max Size 64)WORD
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# inherit ipv6 ospf vrf-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 451
I Commandsinherit ipv6
inherit isis-fabricinherit isis-fabric <WORD>
Description: InterSystem-InterSystem Protocol (IS-IS)
Syntax:
IS-IS Fabric template (Max Size 64)WORD
Command Mode: template pod-group : POD Group
Command Path:
# configure [['terminal', 't']](config)# template pod-group <WORD>(config-pod-group)# inherit isis-fabric <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)452
I Commandsinherit isis-fabric
inherit node-control-policyinherit node-control-policy <WORD>
Description: Associate an node-control policy
Syntax:
Name of node-control policyWORD
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# template leaf-policy-group <WORD>(config-leaf-policy-group)# inherit node-control-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 453
I Commandsinherit node-control-policy
inherit node-onlyinherit node-only bgp timer <WORD>
Description: Inherit node specific BGP Timer Policy
Syntax:
Inherit BGP Timer Policybgp
Inherit BGP Timer Policytimer
BGP Template Policy Name (Max Size 64)WORD
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# inherit node-only bgp timer <WORD>
inherit node-only bgp timer <WORD>
Description: Inherit node specific BGP Timer Policy
Syntax:
Inherit BGP Timer Policybgp
Inherit BGP Timer Policytimer
BGP Template Policy Name (Max Size 64)WORD
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# inherit node-only bgp timer <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)454
I Commandsinherit node-only
inherit ntp-fabricinherit ntp-fabric <WORD>
Description: Network Time Protocol (NTP)
Syntax:
NTP Fabric template (Max Size 64)WORD
Command Mode: template pod-group : POD Group
Command Path:
# configure [['terminal', 't']](config)# template pod-group <WORD>(config-pod-group)# inherit ntp-fabric <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 455
I Commandsinherit ntp-fabric
inherit pod-groupinherit pod-group <WORD>
Description: Pod Group
Syntax:
Pod Group Name (Max Size 64)WORD
Command Mode: pods : Set of PODs
Command Path:
# configure [['terminal', 't']](config)# pod-profile <WORD>(config-pod-profile)# pods <1-255>(config-pod-profile-pods)# inherit pod-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)456
I Commandsinherit pod-group
inherit snmp-fabricinherit snmp-fabric <WORD>
Description: Simple Network Management Protocol (SNMP)
Syntax:
SNMP Fabric template (Max Size 64)WORD
Command Mode: template pod-group : POD Group
Command Path:
# configure [['terminal', 't']](config)# template pod-group <WORD>(config-pod-group)# inherit snmp-fabric <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 457
I Commandsinherit snmp-fabric
inherit vsan-attributeinherit vsan-attribute <WORD>
Description: Configure Vsan Attribute Policy
Syntax:
Configure Vsan Attribute PolicyWORD
Command Mode: vsan-domain : Configure vsan domain
Command Path:
# configure [['terminal', 't']](config)# vsan-domain <name>(config-vsan)# inherit vsan-attribute <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)458
I Commandsinherit vsan-attribute
instanceinstance <NUMBER> vlan <RANGE>
Description:Maps VLANs to an MST instance
Syntax:
MST instance ID. Number range from=1 to=4094<1-4094>
Virtual LANvlan
VLAN range. Ex.: 10-3000RANGE
Command Mode: region : STP MST region configuration mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>(config-stp-region)# instance <NUMBER> vlan <RANGE>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 459
I Commandsinstance
interfaceinterface bridge-domain <WORD>
Description: Configuration for interface bridge-domain
Syntax:
Name of the bridge-domainbridge-domain
Name of the bridge-domain (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>
interface ethernet
Description: Provide a Range of Interfaces
Syntax:
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# interface ethernet
interface ethernet
Description: Provide a Range of Interfaces
Syntax:
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)460
I Commandsinterface
Command Mode: spine-interface-group : Configure Spine Interface Group
Command Path:
# configure [['terminal', 't']](config)# spine-interface-profile <WORD>(config-spine-if-profile)# spine-interface-group <WORD>(config-spine-if-group)# interface ethernet
interface ethernet
Description: Configure Ports on the Fex Interface Group
Syntax:
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# interface ethernet
interface ethernet
Description: Provide a Range of Interfaces
Syntax:
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# interface ethernet
interface vpc <WORD> [fex <fex>]
Description: Provide VPC Name
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 461
I Commandsinterface
VPC Interfacevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Command Mode: vpc context : Enter vpc context
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)462
I Commandsinterface
interface ethernetinterface ethernet <ethernet> leaf <leaf-id>
Description: Configure Physical Ethernet Port as a Cluster Member Interface
Syntax:
List of ethernet itfs<ethernet>
Leaf ID that connects to cluster ethernet interface on (physical) device.leaf
Leaf ID that connects to cluster ethernet interface on (physical) device.<leaf-id>
Command Mode: member : Configure Cluster Interface Member
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>] [context <context>] [trunking <enable|disable>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>(config-member)# interface ethernet <ethernet> leaf <leaf-id>
interface ethernet <ifRange>
Description: Ethernet IEEE 802.3z
Syntax:
interface Range<ifRange>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
interface ethernet <ifRange>
Description: Ethernet IEEE 802.3z
Syntax:
interface Range<ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 463
I Commandsinterface ethernet
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)464
I Commandsinterface ethernet
interface inband-mgmt0interface inband-mgmt0
Description: Inband management interface
Command Mode: controller : Configure Controller Node
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0
interface inband-mgmt0
Description: Inband management interface
Command Mode: switch : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 465
I Commandsinterface inband-mgmt0
interface mgmt0interface mgmt0
Description: Out of band management interface
Command Mode: controller : Configure Controller Node
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0
interface mgmt0
Description: Out of band management interface
Command Mode: switch : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)466
I Commandsinterface mgmt0
interface port-channelinterface port-channel <port-channel-name> leaf <NUMBER> [fex <fex-id>]
Description: Configure Port Channel as a Cluster Member Interface
Syntax:
Name of the port-channel<port-channel-name>
Leaf Id for the port-channelleaf
Leaf Id for the port channel.. Number range from=0to=9223372036854775807
NUMBER
(Optional) Fex ID that connects to cluster interface interface on(physical) device.
<fex-id>
Command Mode: member : Configure Cluster Interface Member
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>] [context <context>] [trunking <enable|disable>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>(config-member)# interface port-channel <port-channel-name> leaf <NUMBER> [fex <fex-id>]
interface port-channel <WORD> [fex <fex>]
Description: Port Channel interface
Syntax:
Port-Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>]
interface port-channel <WORD> [fex <fex>]
Description: Port Channel interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 467
I Commandsinterface port-channel
Syntax:
Port-Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)468
I Commandsinterface port-channel
interface vfc-pointerface vfc-po <WORD> [fex <fex>]
Description: VFC Port Channel interface
Syntax:
Port-Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vfc-po <WORD> [fex <fex>]
interface vfc-po <WORD> [fex <fex>]
Description: VFC Port Channel interface
Syntax:
Port-Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vfc-po <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 469
I Commandsinterface vfc-po
interface vfcinterface vfc <ifRange>
Description: Virtual Fiber Channel interface
Syntax:
interface Range<ifRange>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vfc <ifRange>
interface vfc <ifRange>
Description: Virtual Fiber Channel interface
Syntax:
interface Range<ifRange>
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vfc <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)470
I Commandsinterface vfc
interface vlaninterface vlan <1-4094>
Description: Vlan interface
Syntax:
Vlan interface number<1-4094>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>
interface vlan <1-4094>
Description: Vlan interface
Syntax:
Vlan interface number<1-4094>
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 471
I Commandsinterface vlan
interface vpcinterface vpc <vpc-name> leaf <NUMBER> <NUMBER> [fex fex <Ids>]
Description: Configure monitor for VPC interfaces
Syntax:
VPC port-channel group name<vpc-name>
leafleaf
First leaf member of the Pair. Number range from=0to=9223372036854775807
NUMBER
Second leaf member of the Pair. Number range from=0to=9223372036854775807
NUMBER
(Optional) paired fex Idsfex <Ids>
Command Mode: member : Configure Cluster Interface Member
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>] [context <context>] [trunking <enable|disable>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>(config-member)# interface vpc <vpc-name> leaf <NUMBER> <NUMBER> [fex fex <Ids>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)472
I Commandsinterface vpc
interpodinterpod data hardware-proxy <A.B.C.D>
Description: Interpod anycast hardware-proxy ip
Syntax:
Interpod anycast hardware-proxy ipdata
Interpod anycast hardware-proxy iphardware-proxy
IPV4 address in format x.x.x.xA.B.C.D
Command Mode: pod : Pod Profile
Command Path:
# configure [['terminal', 't']](config)# fabric-external <NUMBER>(config-fabric-external)# pod <NUMBER>(config-fabric-external-pod)# interpod data hardware-proxy <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 473
I Commandsinterpod
ip-inspection-admin-statusip-inspection-admin-status enabled-both|disabled
Description: Config IP inspection administrative status in first hop security bridge domain policy
Syntax:
Enable IP inspection for both IPv4 and IPv6enabled-both
Disable IP inspectiondisabled
Command Mode: security-policy : Configuration for security policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>(config-tenant-fhs-secpol)# ip-inspection-admin-status enabled-both|disabled
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)474
I Commandsip-inspection-admin-status
ipip learning
Description: Instruct the destination leaf to learn source ip of the packet
Syntax:
ip learninglearning
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# ip learning
ip route <A.B.C.D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
Description: Configure IP features
Syntax:
Route informationroute
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
ipAddress|null
<ZeroorPref>
<BfdorPref>
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# ip route <A.B.C.D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
ip <arg> [secondary]
Description: Enable HSRP IP and set the virtual IP address
Syntax:
arg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 475
I Commandsip
(Optional) Configure IP Address as Secondary IPsecondary
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# ip <> [secondary]
ip route <A.B.C.D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
Description: Configure IP features
Syntax:
Route informationroute
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
ipAddress|null
<ZeroorPref>
<BfdorPref>
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# ip route <A.B.C.D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
ip <arg> [secondary]
Description: Enable HSRP IP and set the virtual IP address
Syntax:
arg
(Optional) Configure IP Address as Secondary IPsecondary
Command Mode: hsrp group : Configure HSRP Group
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)476
I Commandsip
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# ip <> [secondary]
ip prefix-list <name> [permit <A.B.C.D/LEN>]
Description: Import Prefix list
Syntax:
Prefix Listprefix-list
Prefix list namename
(Optional) IPV4 address in format x.x.x.x/LENA.B.C.D/LEN
Command Mode: route-map : Import subnet from IPN
Command Path:
# configure [['terminal', 't']](config)# fabric-external <NUMBER>(config-fabric-external)# route-map interpod-import(config-fabric-external-route-map)# ip prefix-list <name> [permit <A.B.C.D/LEN>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 477
I Commandsip
ip address-rangeip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP Address and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Gateway address in format x.x.x.xA.B.C.D
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP address and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Gateway address in format x.x.x.xA.B.C.D
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP Address and network mask length in format x.x.x.x/mA.B.C.D/LEN
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)478
I Commandsip address-range
Configure gateway address on interfacegateway
Gateway address in format x.x.x.xA.B.C.D
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
ip address-range <A.B.C.D> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP address and network mask length in format x.x.x.x/mA.B.C.D
Configure gateway address on interfacegateway
Gateway address in format x.x.x.xA.B.C.D
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ip address-range <A.B.C.D> gateway <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 479
I Commandsip address-range
ip addressip address <A.B.C.D/LEN> [scope <scope>] [secondary] [multi-site] [snooping-querier]
Description: Define an IPv4 subnet to be exported by the BD
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
(Optional) Scope of the address among ['public', 'private']scope
(Optional) Set the address as secondary addresssecondary
(Optional) Set the address as multi-site addressmulti-site
(Optional) Tell the address to be used by IGMP Snooping querierfunctionality if enabled
snooping-querier
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip address <A.B.C.D/LEN> [scope <scope>] [secondary] [multi-site][snooping-querier]
ip address <A.B.C.D/LEN> [secondary]
Description: Configure IP address on interface
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
(Optional) Configure additional IP addresses on interfacesecondary
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip address <A.B.C.D/LEN> [secondary]
ip address <A.B.C.D/LEN> [secondary]
Description: Configure IP address on interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)480
I Commandsip address
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
(Optional) Configure IP Address as Secondary IPsecondary
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip address <A.B.C.D/LEN> [secondary]
ip address <A.B.C.D/LEN> [secondary]
Description: Configure IP address on interface
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
(Optional) Configure additional IP addresses on interfacesecondary
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip address <A.B.C.D/LEN> [secondary]
ip address <A.B.C.D/LEN> [secondary]
Description: Configure IP address on interface
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
(Optional) Configure IP Address as Secondary IPsecondary
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip address <A.B.C.D/LEN> [secondary]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 481
I Commandsip address
ip address <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Gateway address in format x.x.x.xA.B.C.D
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>
ip address <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP address and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Gateway address in format x.x.x.xA.B.C.D
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>
ip address <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Gateway address in format x.x.x.xA.B.C.D
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)482
I Commandsip address
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>
ip address <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP address and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Gateway address in format x.x.x.xA.B.C.D
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 483
I Commandsip address
ip address tenant applicationip address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> application <WORD> epg<WORD>
ip address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)484
I Commandsip address tenant application
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> application <WORD>epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 485
I Commandsip address tenant application
ip address tenant external-l2ip address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>
ip address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l2 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)486
I Commandsip address tenant external-l2
<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 487
I Commandsip address tenant external-l2
ip address tenant external-l3ip address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>
ip address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l3 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)488
I Commandsip address tenant external-l3
<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 489
I Commandsip address tenant external-l3
ip bandwidthip bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip bandwidth eigrp default <NUMBER>
ip bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip bandwidth eigrp default <NUMBER>
ip bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)490
I Commandsip bandwidth
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip bandwidth eigrp default <NUMBER>
ip bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip bandwidth eigrp default <NUMBER>
ip bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 491
I Commandsip bandwidth
(config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip bandwidth eigrp default <NUMBER>
ip bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip bandwidth eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)492
I Commandsip bandwidth
ip bfdip bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip bfd enable
ip bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip bfd eigrp enable
ip bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 493
I Commandsip bfd
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip bfd eigrp enable
ip bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip bfd enable
ip bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip bfd eigrp enable
ip bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)494
I Commandsip bfd
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip bfd eigrp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 495
I Commandsip bfd
ip dhcp relay address tenant applicationip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD>epg <WORD>
ip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>
Description: Application hosting the DHCP server
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the DHCP server (Max Size 63)WORD
Application hosting the DHCP server (Max Size 64)WORD
EPG hosting the DHCP serverepg
EPG hosting the DHCP server (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)496
I Commandsip dhcp relay address tenant application
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD> epg<WORD>
ip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>
Description: Application hosting the DHCP server
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the DHCP server (Max Size 63)WORD
Application hosting the DHCP server (Max Size 64)WORD
EPG hosting the DHCP serverepg
EPG hosting the DHCP server (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD> epg<WORD>
ip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>
Description: Application hosting the DHCP server
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the DHCP server (Max Size 63)WORD
Application hosting the DHCP server (Max Size 64)WORD
EPG hosting the DHCP serverepg
EPG hosting the DHCP server (Max Size 64)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 497
I Commandsip dhcp relay address tenant application
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD> epg<WORD>
ip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>
Description: Application hosting the DHCP server
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the DHCP server (Max Size 63)WORD
Application hosting the DHCP server (Max Size 64)WORD
EPG hosting the DHCP serverepg
EPG hosting the DHCP server (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD> epg<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)498
I Commandsip dhcp relay address tenant application
ip dhcp relay address tenant external-l2ip dhcp relay address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip dhcp relay address <A.B.C.D> tenant <WORD> external-l2 epg<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 499
I Commandsip dhcp relay address tenant external-l2
ip dhcp relay address tenant external-l3ip dhcp relay address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip dhcp relay address <A.B.C.D> tenant <WORD> external-l3 epg<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)500
I Commandsip dhcp relay address tenant external-l3
ip distribute-list eigrpip distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP route-map
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip distribute-list eigrp default route-map <WORD> out
ip distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP Policies
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip distribute-list eigrp default route-map <WORD> out
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 501
I Commandsip distribute-list eigrp
ip distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP route-map
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip distribute-list eigrp default route-map <WORD> out
ip distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP Policies
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip distribute-list eigrp default route-map <WORD> out
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)502
I Commandsip distribute-list eigrp
ip dscpip dscp <dscp>
Description: dscp
Syntax:
DSCP code or valuedscp
Command Mode: destination tenant : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# ip dscp <dscp>
ip dscp <dscp>
Description: dscp
Syntax:
DSCP code or valuedscp
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# ip dscp <dscp>
ip dscp <dscp>
Description: dscp
Syntax:
DSCP code or valuedscp
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 503
I Commandsip dscp
(config)# monitor tenant <tenant_name> session <WORD>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-tenant-dest)# ip dscp <dscp>
ip dscp <dscp>
Description: Configure DSCP
Syntax:
<dscp><dscp>
Command Mode: destination destip : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# ip dscp <dscp>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)504
I Commandsip dscp
ip flowip flow monitor <WORD>
Description: Configure Netflow on the Port-Channel
Syntax:
Configure Netflow on the Port-Channelmonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# ip flow monitor <WORD>
ip flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# ip flow monitor <WORD>
ip flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 505
I Commandsip flow
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip flow monitor <WORD>
ip flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip flow monitor <WORD>
ip flow monitor <arg>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip flow monitor <>
ip flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)506
I Commandsip flow
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# ip flow monitor <WORD>
ip flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip flow monitor <WORD>
ip flow monitor <arg>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip flow monitor <>
ip flow monitor <WORD>
Description: Configure Netflow on the Interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 507
I Commandsip flow
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# ip flow monitor <WORD>
ip flow monitor <WORD>
Description: Configure Netflow on the VPC
Syntax:
Configure Netflow on the VPCmonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# ip flow monitor <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)508
I Commandsip flow
ip hello-intervalip hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip hello-interval eigrp default <NUMBER>
ip hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip hello-interval eigrp default <NUMBER>
ip hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 509
I Commandsip hello-interval
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip hello-interval eigrp default <NUMBER>
ip hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip hello-interval eigrp default <NUMBER>
ip hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)510
I Commandsip hello-interval
(config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip hello-interval eigrp default <NUMBER>
ip hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip hello-interval eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 511
I Commandsip hello-interval
ip hold-intervalip hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip hold-interval eigrp default <NUMBER>
ip hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip hold-interval eigrp default <NUMBER>
ip hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)512
I Commandsip hold-interval
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip hold-interval eigrp default <NUMBER>
ip hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip hold-interval eigrp default <NUMBER>
ip hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 513
I Commandsip hold-interval
(config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip hold-interval eigrp default <NUMBER>
ip hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip hold-interval eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)514
I Commandsip hold-interval
ip igmpip igmp
Description: Enable IGMP
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip igmp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 515
I Commandsip igmp
ip igmp allow-v3-asmip igmp allow-v3-asm
Description: Allow V3 ASM
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp allow-v3-asm
ip igmp allow-v3-asm
Description: Allow V3 ASM
Syntax:
igmpigmp
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp allow-v3-asm
ip igmp allow-v3-asm
Description: Allow V3 ASM
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp allow-v3-asm
ip igmp allow-v3-asm
Description: Allow V3 ASM
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)516
I Commandsip igmp allow-v3-asm
(config-leaf-if)# ip igmp allow-v3-asm
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 517
I Commandsip igmp allow-v3-asm
ip igmp fast-leaveip igmp fast-leave
Description: Enable IP IGMP fast leave processing
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp fast-leave
ip igmp fast-leave
Description: Enable IP IGMP fast leave processing
Syntax:
igmpigmp
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp fast-leave
ip igmp fast-leave
Description: Enable IP IGMP fast leave processing
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp fast-leave
ip igmp fast-leave
Description: Enable IP IGMP fast leave processing
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)518
I Commandsip igmp fast-leave
(config-leaf-if)# ip igmp fast-leave
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 519
I Commandsip igmp fast-leave
ip igmp group-timeoutip igmp group-timeout <NUMBER>
Description: Configures group membership timeout for IGMPv2
Syntax:
Time in seconds. Number range from=3 to=65535<3-65535>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp group-timeout <NUMBER>
ip igmp group-timeout <NUMBER>
Description: Configures group membership timeout for IGMPv2
Syntax:
igmpigmp
Time in seconds. Number range from=3 to=65535<3-65535>
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp group-timeout <NUMBER>
ip igmp group-timeout <NUMBER>
Description: Configures group membership timeout for IGMPv2
Syntax:
Time in seconds. Number range from=3 to=65535<3-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)520
I Commandsip igmp group-timeout
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp group-timeout <NUMBER>
ip igmp group-timeout <NUMBER>
Description: Configures group membership timeout for IGMPv2
Syntax:
Time in seconds. Number range from=3 to=65535<3-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp group-timeout <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 521
I Commandsip igmp group-timeout
ip igmp inheritip igmp inherit interface-policy <WORD> [tenant <WORD>]
Description: Associate a IGMP interface policy to this interface
Syntax:
interface-policyinterface-policy
IGMP inteface policy name (Max Size 64)WORD
(Optional) Tenant where policy is definedWORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp inherit interface-policy <WORD> [tenant <WORD>]
ip igmp inherit interface-policy <WORD> [tenant <WORD>]
Description: Associate a IGMP interface policy to this interface
Syntax:
interface-policyinterface-policy
IGMP inteface policy name (Max Size 64)WORD
(Optional) Tenant where policy is definedWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp inherit interface-policy <WORD> [tenant <WORD>]
ip igmp inherit interface-policy <WORD> [tenant <WORD>]
Description: Associate a IGMP interface policy to this interface
Syntax:
interface-policyinterface-policy
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)522
I Commandsip igmp inherit
IGMP inteface policy name (Max Size 64)WORD
(Optional) Tenant where policy is definedWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp inherit interface-policy <WORD> [tenant <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 523
I Commandsip igmp inherit
ip igmp last-member-query-countip igmp last-member-query-count <NUMBER>
Description: Configures number of group-specific Queries sent
Syntax:
Count value. Number range from=1 to=5<1-5>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp last-member-query-count <NUMBER>
ip igmp last-member-query-count <NUMBER>
Description: Configures number of group-specific Queries sent
Syntax:
igmpigmp
Count value. Number range from=1 to=5<1-5>
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp last-member-query-count <NUMBER>
ip igmp last-member-query-count <NUMBER>
Description: Configures number of group-specific Queries sent
Syntax:
Count value. Number range from=1 to=5<1-5>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)524
I Commandsip igmp last-member-query-count
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp last-member-query-count <NUMBER>
ip igmp last-member-query-count <NUMBER>
Description: Configures number of group-specific Queries sent
Syntax:
Count value. Number range from=1 to=5<1-5>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp last-member-query-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 525
I Commandsip igmp last-member-query-count
ip igmp last-member-query-response-timeip igmp last-member-query-response-time <NUMBER>
Description: Configures last member query response time
Syntax:
Time in seconds. Number range from=1 to=25<1-25>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp last-member-query-response-time <NUMBER>
ip igmp last-member-query-response-time <NUMBER>
Description: Configures last member query response time
Syntax:
igmpigmp
Time in seconds. Number range from=1 to=25<1-25>
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp last-member-query-response-time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)526
I Commandsip igmp last-member-query-response-time
ip igmp querier-timeoutip igmp querier-timeout <NUMBER>
Description: Configures querier timeout for IGMPv2
Syntax:
Time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp querier-timeout <NUMBER>
ip igmp querier-timeout <NUMBER>
Description: Configures querier timeout for IGMPv2
Syntax:
igmpigmp
Time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp querier-timeout <NUMBER>
ip igmp querier-timeout <NUMBER>
Description: Configures querier timeout for IGMPv2
Syntax:
Time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 527
I Commandsip igmp querier-timeout
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp querier-timeout <NUMBER>
ip igmp querier-timeout <NUMBER>
Description: Configures querier timeout for IGMPv2
Syntax:
Time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp querier-timeout <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)528
I Commandsip igmp querier-timeout
ip igmp query-intervalip igmp query-interval <NUMBER>
Description: Configures interval between Query transmission
Syntax:
Time in seconds. Number range from=1 to=18000<1-18000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp query-interval <NUMBER>
ip igmp query-interval <NUMBER>
Description: Configures interval between Query transmission
Syntax:
igmpigmp
Time in seconds. Number range from=1 to=18000<1-18000>
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp query-interval <NUMBER>
ip igmp query-interval <NUMBER>
Description: Configures interval between Query transmission
Syntax:
Time in seconds. Number range from=1 to=18000<1-18000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 529
I Commandsip igmp query-interval
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp query-interval <NUMBER>
ip igmp query-interval <NUMBER>
Description: Configures interval between Query transmission
Syntax:
Time in seconds. Number range from=1 to=18000<1-18000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp query-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)530
I Commandsip igmp query-interval
ip igmp query-max-response-timeip igmp query-max-response-time <NUMBER>
Description: Configures MRT for query messages
Syntax:
Time in seconds. Number range from=1 to=25<1-25>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp query-max-response-time <NUMBER>
ip igmp query-max-response-time <NUMBER>
Description: Configures MRT for query messages
Syntax:
igmpigmp
Time in seconds. Number range from=1 to=25<1-25>
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp query-max-response-time <NUMBER>
ip igmp query-max-response-time <NUMBER>
Description: Configures MRT for query messages
Syntax:
Time in seconds. Number range from=1 to=25<1-25>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 531
I Commandsip igmp query-max-response-time
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp query-max-response-time <NUMBER>
ip igmp query-max-response-time <NUMBER>
Description: Configures MRT for query messages
Syntax:
Time in seconds. Number range from=1 to=25<1-25>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp query-max-response-time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)532
I Commandsip igmp query-max-response-time
ip igmp report-link-local-groupsip igmp report-link-local-groups
Description: Send Reports for groups in 224.0.0.0/24
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp report-link-local-groups
ip igmp report-link-local-groups
Description: Send Reports for groups in 224.0.0.0/24
Syntax:
igmpigmp
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp report-link-local-groups
ip igmp report-link-local-groups
Description: Send Reports for groups in 224.0.0.0/24
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp report-link-local-groups
ip igmp report-link-local-groups
Description: Send Reports for groups in 224.0.0.0/24
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 533
I Commandsip igmp report-link-local-groups
(config-leaf-if)# ip igmp report-link-local-groups
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)534
I Commandsip igmp report-link-local-groups
ip igmp report-policyip igmp report-policy <WORD>
Description: Configure IGMP report policy
Syntax:
Route-map nameWORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp report-policy <WORD>
ip igmp report-policy <WORD>
Description: Configure IGMP report policy
Syntax:
igmpigmp
Route-map nameWORD
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp report-policy <WORD>
ip igmp report-policy <WORD>
Description: Configure IGMP report policy
Syntax:
Route-map nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 535
I Commandsip igmp report-policy
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp report-policy <WORD>
ip igmp report-policy <WORD>
Description: Configure IGMP report policy
Syntax:
Route-map nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp report-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)536
I Commandsip igmp report-policy
ip igmp robustness-variableip igmp robustness-variable <NUMBER>
Description: Configures RFC defined Robustness Variable
Syntax:
Count value. Number range from=1 to=7<1-7>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp robustness-variable <NUMBER>
ip igmp robustness-variable <NUMBER>
Description: Configures RFC defined Robustness Variable
Syntax:
igmpigmp
Count value. Number range from=1 to=7<1-7>
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp robustness-variable <NUMBER>
ip igmp robustness-variable <NUMBER>
Description: Configures RFC defined Robustness Variable
Syntax:
Count value. Number range from=1 to=7<1-7>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 537
I Commandsip igmp robustness-variable
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp robustness-variable <NUMBER>
ip igmp robustness-variable <NUMBER>
Description: Configures RFC defined Robustness Variable
Syntax:
Count value. Number range from=1 to=7<1-7>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp robustness-variable <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)538
I Commandsip igmp robustness-variable
ip igmp snoopingip igmp snooping
Description: IP IGMP snooping settings
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping
ip igmp snooping
Description: IP IGMP snooping settings
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 539
I Commandsip igmp snooping
ip igmp snooping access-group route-map leaf interfaceethernet ethernet vlan
ip igmp snooping access-group route-map <WORD> leaf <WORD> interface ethernet ethernet <slot>/<port>vlan <VLAN>
Description: Encap VLAN
Syntax:
Route-Map used for filteringroute-map
route-map name (Max Size 64)WORD
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Interface keywordinterface
Ethernet Rangeethernet <slot>/<port>
Encap VLANVLAN
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# ip igmp snooping access-group route-map <WORD> leaf <WORD> interfaceethernet ethernet <slot>/<port> vlan <VLAN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)540
I Commandsip igmp snooping access-group route-map leaf interface ethernet ethernet vlan
ip igmp snooping access-group route-map leaf interfaceport-channel vlan
ip igmp snooping access-group route-map <WORD> leaf <WORD> interface port-channel <WORD> [fex<NUMBER>] vlan <VLAN>
Description: Encap VLAN
Syntax:
Route-Map used for filteringroute-map
route-map name (Max Size 64)WORD
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Interface keywordinterface
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199<101-199>
Encap VLANVLAN
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# ip igmp snooping access-group route-map <WORD> leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>] vlan <VLAN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 541
I Commandsip igmp snooping access-group route-map leaf interface port-channel vlan
ip igmp snooping access-group route-map vpc context interfacevpc vlan
ip igmp snooping access-group route-map <WORD> vpc context <WORD> <WORD> interface vpc <WORD>[fex <fex>] vlan <VLAN>
Description: Encap VLAN
Syntax:
Route-Map used for filteringroute-map
route-map name (Max Size 64)WORD
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Encap VLANVLAN
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# ip igmp snooping access-group route-map <WORD> vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>] vlan <VLAN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)542
I Commandsip igmp snooping access-group route-map vpc context interface vpc vlan
ip igmp snooping fast-leaveip igmp snooping fast-leave
Description: Enable IP IGMP Snooping fast leave processing
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping fast-leave
ip igmp snooping fast-leave
Description: Enable IP IGMP Snooping fast leave processing
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping fast-leave
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 543
I Commandsip igmp snooping fast-leave
ip igmp snooping last-member-query-intervalip igmp snooping last-member-query-interval <NUMBER>
Description: Change the IP IGMP snooping last member query interval param
Syntax:
Last Memeber Query Interval Value. Number range from=1 to=25<1-25>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping last-member-query-interval <NUMBER>
ip igmp snooping last-member-query-interval <NUMBER>
Description: Change the IP IGMP snooping last member query interval param
Syntax:
Last Memeber Query Interval Value. Number range from=1 to=25<1-25>
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping last-member-query-interval<NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)544
I Commandsip igmp snooping last-member-query-interval
ip igmp snooping policyip igmp snooping policy <WORD>
Description: Associate the BD with an IGMP snooping policy
Syntax:
Name of the IGMP snooping policy to attach (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 545
I Commandsip igmp snooping policy
ip igmp snooping querierip igmp snooping querier
Description: Enable IP IGMP Snooping querier processing
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping querier
ip igmp snooping querier
Description: Enable IP IGMP Snooping querier processing
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping querier
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)546
I Commandsip igmp snooping querier
ip igmp snooping query-intervalip igmp snooping query-interval <NUMBER>
Description: Change the IP IGMP snooping query interval param
Syntax:
Query Interval Value. Number range from=1 to=18000<1-18000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping query-interval <NUMBER>
ip igmp snooping query-interval <NUMBER>
Description: Change the IP IGMP snooping query interval param
Syntax:
Query Interval Value. Number range from=1 to=18000<1-18000>
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping query-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 547
I Commandsip igmp snooping query-interval
ip igmp snooping query-max-response-timeip igmp snooping query-max-response-time <NUMBER>
Description: Change the IP IGMP snooping max query response time
Syntax:
Query Max Response Time. Number range from=1 to=25<1-25>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping query-max-response-time <NUMBER>
ip igmp snooping query-max-response-time <NUMBER>
Description: Change the IP IGMP snooping max query response time
Syntax:
Query Max Response Time. Number range from=1 to=25<1-25>
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping query-max-response-time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)548
I Commandsip igmp snooping query-max-response-time
ip igmp snooping startup-query-countip igmp snooping startup-query-count <NUMBER>
Description: Change the IP IGMP snooping number of initial queries to send
Syntax:
Start Query Count. Number range from=1 to=10<1-10>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping startup-query-count <NUMBER>
ip igmp snooping startup-query-count <NUMBER>
Description: Change the IP IGMP snooping number of initial queries to send
Syntax:
Start Query Count. Number range from=1 to=10<1-10>
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping startup-query-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 549
I Commandsip igmp snooping startup-query-count
ip igmp snooping startup-query-intervalip igmp snooping startup-query-interval <NUMBER>
Description: Change the IP IGMP snooping time for sending initial queries
Syntax:
Start Query Interval Value. Number range from=1 to=18000<1-18000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping startup-query-interval <NUMBER>
ip igmp snooping startup-query-interval <NUMBER>
Description: Change the IP IGMP snooping time for sending initial queries
Syntax:
Start Query Interval Value. Number range from=1 to=18000<1-18000>
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping startup-query-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)550
I Commandsip igmp snooping startup-query-interval
ip igmp snooping static-group leaf interface ethernet ethernetvlan
ip igmp snooping static-group <A.B.C.D> [source <A.B.C.D>] leaf <WORD> interface ethernet ethernet<slot>/<port> vlan <VLAN>
Description: Encap VLAN
Syntax:
IP Multicast address in format i.i.i.iA.B.C.D
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Interface keywordinterface
Ethernet Rangeethernet <slot>/<port>
Encap VLANVLAN
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# ip igmp snooping static-group <A.B.C.D> [source <A.B.C.D>] leaf<WORD> interface ethernet ethernet <slot>/<port> vlan <VLAN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 551
I Commandsip igmp snooping static-group leaf interface ethernet ethernet vlan
ip igmp snooping static-group leaf interface port-channel vlanip igmp snooping static-group <A.B.C.D> [source <A.B.C.D>] leaf <WORD> interface port-channel <WORD>[fex <NUMBER>] vlan <VLAN>
Description: Encap VLAN
Syntax:
IP Multicast address in format i.i.i.iA.B.C.D
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Interface keywordinterface
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199<101-199>
Encap VLANVLAN
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# ip igmp snooping static-group <A.B.C.D> [source <A.B.C.D>] leaf<WORD> interface port-channel <WORD> [fex <NUMBER>] vlan <VLAN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)552
I Commandsip igmp snooping static-group leaf interface port-channel vlan
ip igmp snooping static-group vpc context interface vpc vlanip igmp snooping static-group <A.B.C.D> [source <A.B.C.D>] vpc context <WORD> <WORD> interface vpc<WORD> [fex <fex>] vlan <VLAN>
Description: Encap VLAN
Syntax:
IP Multicast address in format i.i.i.iA.B.C.D
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Encap VLANVLAN
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# ip igmp snooping static-group <A.B.C.D> [source <A.B.C.D>] vpccontext <WORD> <WORD> interface vpc <WORD> [fex <fex>] vlan <VLAN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 553
I Commandsip igmp snooping static-group vpc context interface vpc vlan
ip igmp ssm-translateip igmp ssm-translate <A.B.C.D/LEN> <A.B.C.D>
Description: Translate IGMPv1/v2 reports to (S,G) route entries
Syntax:
IP Multicast group rangeA.B.C.D/LEN
IP Multicast address sourceA.B.C.D
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip igmp ssm-translate <A.B.C.D/LEN> <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)554
I Commandsip igmp ssm-translate
ip igmp startup-query-countip igmp startup-query-count <NUMBER>
Description: Configures number of queries sent at startup
Syntax:
Time in seconds. Number range from=1 to=10<1-10>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp startup-query-count <NUMBER>
ip igmp startup-query-count <NUMBER>
Description: Configures number of queries sent at startup
Syntax:
igmpigmp
Time in seconds. Number range from=1 to=10<1-10>
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp startup-query-count <NUMBER>
ip igmp startup-query-count <NUMBER>
Description: Configures number of queries sent at startup
Syntax:
Time in seconds. Number range from=1 to=10<1-10>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 555
I Commandsip igmp startup-query-count
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp startup-query-count <NUMBER>
ip igmp startup-query-count <NUMBER>
Description: Configures number of queries sent at startup
Syntax:
Time in seconds. Number range from=1 to=10<1-10>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp startup-query-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)556
I Commandsip igmp startup-query-count
ip igmp startup-query-intervalip igmp startup-query-interval <NUMBER>
Description: Configures query interval at startup
Syntax:
Time in seconds. Number range from=1 to=18000<1-18000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp startup-query-interval <NUMBER>
ip igmp startup-query-interval <NUMBER>
Description: Configures query interval at startup
Syntax:
igmpigmp
Time in seconds. Number range from=1 to=18000<1-18000>
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp startup-query-interval <NUMBER>
ip igmp startup-query-interval <NUMBER>
Description: Configures query interval at startup
Syntax:
Time in seconds. Number range from=1 to=18000<1-18000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 557
I Commandsip igmp startup-query-interval
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp startup-query-interval <NUMBER>
ip igmp startup-query-interval <NUMBER>
Description: Configures query interval at startup
Syntax:
Time in seconds. Number range from=1 to=18000<1-18000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp startup-query-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)558
I Commandsip igmp startup-query-interval
ip igmp state-limitip igmp state-limit <NUMBER>
Description: Configures State limit
Syntax:
Maximum states allowed. Number range from=1 to=4294967295<1-4294967295>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp state-limit <NUMBER>
ip igmp state-limit <NUMBER>
Description: Configures State limit
Syntax:
igmpigmp
Maximum states allowed. Number range from=1 to=4294967295<1-4294967295>
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp state-limit <NUMBER>
ip igmp state-limit <NUMBER>
Description: Configures State limit
Syntax:
Maximum states allowed. Number range from=1 to=4294967295<1-4294967295>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 559
I Commandsip igmp state-limit
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp state-limit <NUMBER>
ip igmp state-limit <NUMBER>
Description: Configures State limit
Syntax:
Maximum states allowed. Number range from=1 to=4294967295<1-4294967295>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp state-limit <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)560
I Commandsip igmp state-limit
ip igmp state-limit reservedip igmp state-limit <NUMBER> reserved <WORD> <NUMBER>
Description: Reserve the states using route-map
Syntax:
Maximum states allowed. Number range from=1 to=4294967295<1-4294967295>
Route-map nameWORD
Maximum (*,G)/(S,G) entires allowed on the interface. Number rangefrom=0 to=4294967295
<0-4294967295>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp state-limit <NUMBER> reserved <WORD> <NUMBER>
ip igmp state-limit <NUMBER> reserved <WORD> <NUMBER>
Description: Reserve the states using route-map
Syntax:
igmpigmp
Maximum states allowed. Number range from=1 to=4294967295<1-4294967295>
Route-map nameWORD
Maximum (*,G)/(S,G) entires allowed on the interface. Number rangefrom=0 to=4294967295
<0-4294967295>
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp state-limit <NUMBER> reserved <WORD><NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 561
I Commandsip igmp state-limit reserved
ip igmp state-limit <NUMBER> reserved <WORD> <NUMBER>
Description: Reserve the states using route-map
Syntax:
Maximum states allowed. Number range from=1 to=4294967295<1-4294967295>
Route-map nameWORD
Maximum (*,G)/(S,G) entires allowed on the interface. Number rangefrom=0 to=4294967295
<0-4294967295>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp state-limit <NUMBER> reserved <WORD> <NUMBER>
ip igmp state-limit <NUMBER> reserved <WORD> <NUMBER>
Description: Reserve the states using route-map
Syntax:
Maximum states allowed. Number range from=1 to=4294967295<1-4294967295>
Route-map nameWORD
Maximum (*,G)/(S,G) entires allowed on the interface. Number rangefrom=0 to=4294967295
<0-4294967295>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp state-limit <NUMBER> reserved <WORD> <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)562
I Commandsip igmp state-limit reserved
ip igmp static-oifip igmp static-oif route-map <WORD>
Description: Configures static oif for a multicast forwarding
Syntax:
route-maproute-map
Route-map nameWORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp static-oif route-map <WORD>
ip igmp static-oif route-map <WORD>
Description: Configures static oif for a multicast forwarding
Syntax:
igmpigmp
route-maproute-map
Route-map nameWORD
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp static-oif route-map <WORD>
ip igmp static-oif route-map <WORD>
Description: Configures static oif for a multicast forwarding
Syntax:
route-maproute-map
Route-map nameWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 563
I Commandsip igmp static-oif
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp static-oif route-map <WORD>
ip igmp static-oif route-map <WORD>
Description: Configures static oif for a multicast forwarding
Syntax:
route-maproute-map
Route-map nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp static-oif route-map <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)564
I Commandsip igmp static-oif
ip igmp versionip igmp version <arg>
Description: Configures IGMP version number for interface
Syntax:
IGMP version numberarg
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp version <>
ip igmp version <arg>
Description: Configures IGMP version number for interface
Syntax:
igmpigmp
IGMP version numberarg
Command Mode: template ip igmp interface-policy : Create an IGMP interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp interface-policy <WORD>(config-tenant-template-ip-igmp-policy)# ip igmp version <>
ip igmp version <arg>
Description: Configures IGMP version number for interface
Syntax:
IGMP version numberarg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 565
I Commandsip igmp version
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip igmp version <>
ip igmp version <arg>
Description: Configures IGMP version number for interface
Syntax:
IGMP version numberarg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip igmp version <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)566
I Commandsip igmp version
ip multicastip multicast
Description: Enable multicast on this bridge-domain
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip multicast
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 567
I Commandsip multicast
ip next-hop-selfip next-hop-self eigrp default
Description: Set the next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip next-hop-self eigrp default
ip next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip next-hop-self eigrp default
ip next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)568
I Commandsip next-hop-self
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip next-hop-self eigrp default
ip next-hop-self eigrp default
Description: Set the next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip next-hop-self eigrp default
ip next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip next-hop-self eigrp default
ip next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 569
I Commandsip next-hop-self
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip next-hop-self eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)570
I Commandsip next-hop-self
ip ospf authentication-keyip ospf authentication-key <WORD>
Description: Set OSPF authentication key
Syntax:
OSPF authentication keyWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf authentication-key <WORD>
ip ospf authentication-key <WORD>
Description: Set OSPF authentication key
Syntax:
OSPF authentication keyWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf authentication-key <WORD>
ip ospf authentication-key <WORD>
Description: Set OSPF authentication key
Syntax:
OSPF authentication keyWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 571
I Commandsip ospf authentication-key
(config-leaf-if)# ip ospf authentication-key <WORD>
ip ospf authentication-key <WORD>
Description: Set OSPF authentication key
Syntax:
OSPF authentication keyWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf authentication-key <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)572
I Commandsip ospf authentication-key
ip ospf authenticationip ospf authentication md5|none|simple
Description: Set the OSPF authentication type
Syntax:
MD5 authenticationmd5
No authenticationnone
Simple authenticationsimple
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf authentication md5|none|simple
ip ospf authentication md5|none|simple
Description: Set the OSPF authentication type
Syntax:
MD5 authenticationmd5
No authenticationnone
Simple authenticationsimple
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf authentication md5|none|simple
ip ospf authentication md5|none|simple
Description: Set the OSPF authentication type
Syntax:
MD5 authenticationmd5
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 573
I Commandsip ospf authentication
No authenticationnone
Simple authenticationsimple
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip ospf authentication md5|none|simple
ip ospf authentication md5|none|simple
Description: Set the OSPF authentication type
Syntax:
MD5 authenticationmd5
No authenticationnone
Simple authenticationsimple
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf authentication md5|none|simple
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)574
I Commandsip ospf authentication
ip ospf bfdip ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf bfd enable
ip ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf bfd enable
ip ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 575
I Commandsip ospf bfd
(config-leaf-if)# ip ospf bfd enable
ip ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf bfd enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)576
I Commandsip ospf bfd
ip ospf costip ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf cost <NUMBER>
ip ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf cost <NUMBER>
ip ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 577
I Commandsip ospf cost
(config-leaf-if)# ip ospf cost <NUMBER>
ip ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf cost <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)578
I Commandsip ospf cost
ip ospf dead-intervalip ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf dead-interval <NUMBER>
ip ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf dead-interval <NUMBER>
ip ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 579
I Commandsip ospf dead-interval
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip ospf dead-interval <NUMBER>
ip ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf dead-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)580
I Commandsip ospf dead-interval
ip ospf hello-intervalip ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf hello-interval <NUMBER>
ip ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf hello-interval <NUMBER>
ip ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 581
I Commandsip ospf hello-interval
(config-leaf-if)# ip ospf hello-interval <NUMBER>
ip ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf hello-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)582
I Commandsip ospf hello-interval
ip ospf inheritip ospf inherit interface-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf inherit interface-policy <WORD>
ip ospf inherit interface-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf inherit interface-policy <WORD>
ip ospf inherit interface-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 583
I Commandsip ospf inherit
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip ospf inherit interface-policy <WORD>
ip ospf inherit interface-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf inherit interface-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)584
I Commandsip ospf inherit
ip ospf mtu-ignoreip ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf mtu-ignore
ip ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf mtu-ignore
ip ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip ospf mtu-ignore
ip ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf mtu-ignore
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 585
I Commandsip ospf mtu-ignore
ip ospf networkip ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf network bcast|p2p|unspecified
ip ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf network bcast|p2p|unspecified
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)586
I Commandsip ospf network
ip ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip ospf network bcast|p2p|unspecified
ip ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf network bcast|p2p|unspecified
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 587
I Commandsip ospf network
ip ospf passive-interfaceip ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf passive-interface
ip ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf passive-interface
ip ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip ospf passive-interface
ip ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf passive-interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)588
I Commandsip ospf passive-interface
ip ospf prefix-suppressionip ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf prefix-suppression disable|enable|inherit
ip ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf prefix-suppression disable|enable|inherit
ip ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 589
I Commandsip ospf prefix-suppression
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip ospf prefix-suppression disable|enable|inherit
ip ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf prefix-suppression disable|enable|inherit
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)590
I Commandsip ospf prefix-suppression
ip ospf priorityip ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf priority <NUMBER>
ip ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf priority <NUMBER>
ip ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 591
I Commandsip ospf priority
(config-leaf-if)# ip ospf priority <NUMBER>
ip ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf priority <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)592
I Commandsip ospf priority
ip ospf retransmit-intervalip ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf retransmit-interval <NUMBER>
ip ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf retransmit-interval <NUMBER>
ip ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 593
I Commandsip ospf retransmit-interval
(config-leaf-if)# ip ospf retransmit-interval <NUMBER>
ip ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf retransmit-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)594
I Commandsip ospf retransmit-interval
ip ospf transmit-delayip ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf transmit-delay <NUMBER>
ip ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf transmit-delay <NUMBER>
ip ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 595
I Commandsip ospf transmit-delay
(config-leaf-if)# ip ospf transmit-delay <NUMBER>
ip ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip ospf transmit-delay <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)596
I Commandsip ospf transmit-delay
ip passive-interfaceip passive-interface eigrp default
Description: Set the passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip passive-interface eigrp default
ip passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip passive-interface eigrp default
ip passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 597
I Commandsip passive-interface
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip passive-interface eigrp default
ip passive-interface eigrp default
Description: Set the passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip passive-interface eigrp default
ip passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip passive-interface eigrp default
ip passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)598
I Commandsip passive-interface
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip passive-interface eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 599
I Commandsip passive-interface
ip pimip pim
Description: Enable PIM
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim
ip pim
Description: Enable PIM
Command Mode: l3out : Configuration for L3Out
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l3out <WORD>(config-tenant-l3out)# ip pim
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)600
I Commandsip pim
ip pim auto-rp forwardip pim auto-rp forward listen
Description: Forward Auto-RP messages
Syntax:
Listen to Auto-RP messageslisten
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim auto-rp forward listen
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 601
I Commandsip pim auto-rp forward
ip pim auto-rp listenip pim auto-rp listen forward
Description: Listen to Auto-RP messages
Syntax:
Forward Auto-RP messagesforward
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim auto-rp listen forward
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)602
I Commandsip pim auto-rp listen
ip pim auto-rp mapping-agent-policyip pim auto-rp mapping-agent-policy <WORD>
Description: Associate route-map policy for filtering Mapping Agent messages
Syntax:
Route-map nameWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim auto-rp mapping-agent-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 603
I Commandsip pim auto-rp mapping-agent-policy
ip pim borderip pim border
Description: Configures interface to be a boundary of a PIM domain
Syntax:
pimpim
Command Mode: template ip pim interface-policy : Create a PIM interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip pim interface-policy <WORD>(config-tenant-template-ip-pim)# ip pim border
ip pim border
Description: Configures interface to be a boundary of a PIM domain
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim border
ip pim border
Description: Configures interface to be a boundary of a PIM domain
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip pim border
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)604
I Commandsip pim border
ip pim bsr bsr-policyip pim bsr bsr-policy <WORD>
Description: Associate route-map policy for filtering BSR messages
Syntax:
Route-map nameWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim bsr bsr-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 605
I Commandsip pim bsr bsr-policy
ip pim bsr forwardip pim bsr forward listen
Description: Forward Bootstrap/Candidate-RP messages
Syntax:
Listen to Bootstrap/Candidate-RP messageslisten
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim bsr forward listen
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)606
I Commandsip pim bsr forward
ip pim bsr listenip pim bsr listen forward
Description: Listen to Bootstrap/Candidate-RP messages
Syntax:
Forward Bootstrap/Candidate-RP messagesforward
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim bsr listen forward
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 607
I Commandsip pim bsr listen
ip pim dr-delayip pim dr-delay <NUMBER>
Description: Configures delay for PIM DR election on interface
Syntax:
pimpim
DR Delay Value in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template ip pim interface-policy : Create a PIM interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip pim interface-policy <WORD>(config-tenant-template-ip-pim)# ip pim dr-delay <NUMBER>
ip pim dr-delay <NUMBER>
Description: Configures delay for PIM DR election on interface
Syntax:
DR Delay Value in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim dr-delay <NUMBER>
ip pim dr-delay <NUMBER>
Description: Configures delay for PIM DR election on interface
Syntax:
DR Delay Value in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)608
I Commandsip pim dr-delay
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip pim dr-delay <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 609
I Commandsip pim dr-delay
ip pim dr-priorityip pim dr-priority <NUMBER>
Description: Configures priority for PIM DR election on interface
Syntax:
pimpim
DR priority. Number range from=1 to=4294967295<1-4294967295>
Command Mode: template ip pim interface-policy : Create a PIM interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip pim interface-policy <WORD>(config-tenant-template-ip-pim)# ip pim dr-priority <NUMBER>
ip pim dr-priority <NUMBER>
Description: Configures priority for PIM DR election on interface
Syntax:
DR priority. Number range from=1 to=4294967295<1-4294967295>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim dr-priority <NUMBER>
ip pim dr-priority <NUMBER>
Description: Configures priority for PIM DR election on interface
Syntax:
DR priority. Number range from=1 to=4294967295<1-4294967295>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)610
I Commandsip pim dr-priority
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip pim dr-priority <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 611
I Commandsip pim dr-priority
ip pim fast-convergenceip pim fast-convergence
Description: Set PIM fast convergence
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim fast-convergence
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)612
I Commandsip pim fast-convergence
ip pim hello-authenticationip pim hello-authentication ah-md5 <WORD>
Description: Add AH header option to Hellos
Syntax:
pimpim
MD5 authenticationah-md5
PIM hello authentication keyWORD
Command Mode: template ip pim interface-policy : Create a PIM interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip pim interface-policy <WORD>(config-tenant-template-ip-pim)# ip pim hello-authentication ah-md5 <WORD>
ip pim hello-authentication ah-md5 <WORD>
Description: Add AH header option to Hellos
Syntax:
MD5 authenticationah-md5
PIM hello authentication keyWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim hello-authentication ah-md5 <WORD>
ip pim hello-authentication ah-md5 <WORD>
Description: Add AH header option to Hellos
Syntax:
MD5 authenticationah-md5
PIM hello authentication keyWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 613
I Commandsip pim hello-authentication
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip pim hello-authentication ah-md5 <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)614
I Commandsip pim hello-authentication
ip pim hello-intervalip pim hello-interval <NUMBER>
Description: Configures the Hello interval for the interface
Syntax:
pimpim
Hello Interval Value. Number range from=1 to=18724286<1-18724286>
Command Mode: template ip pim interface-policy : Create a PIM interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip pim interface-policy <WORD>(config-tenant-template-ip-pim)# ip pim hello-interval <NUMBER>
ip pim hello-interval <NUMBER>
Description: Configures the Hello interval for the interface
Syntax:
Hello Interval Value in milliseconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim hello-interval <NUMBER>
ip pim hello-interval <NUMBER>
Description: Configures the Hello interval for the interface
Syntax:
Hello Interval Value in milliseconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 615
I Commandsip pim hello-interval
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip pim hello-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)616
I Commandsip pim hello-interval
ip pim inheritip pim inherit interface-policy <WORD> [tenant <WORD>]
Description: Associate a PIM interface policy to this interface
Syntax:
interface-policyinterface-policy
PIM inteface policy name (Max Size 64)WORD
(Optional) Tenant where policy is definedWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim inherit interface-policy <WORD> [tenant <WORD>]
ip pim inherit interface-policy <WORD> [tenant <WORD>]
Description: Associate a PIM interface policy to this interface
Syntax:
interface-policyinterface-policy
PIM inteface policy name (Max Size 64)WORD
(Optional) Tenant where policy is definedWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip pim inherit interface-policy <WORD> [tenant <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 617
I Commandsip pim inherit
ip pim jp-intervalip pim jp-interval <NUMBER>
Description: Configures the Join-Prune interval for the interface
Syntax:
pimpim
JP Interval Value. Number range from=60 to=65520<60-65520>
Command Mode: template ip pim interface-policy : Create a PIM interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip pim interface-policy <WORD>(config-tenant-template-ip-pim)# ip pim jp-interval <NUMBER>
ip pim jp-interval <NUMBER>
Description: Configures the Join-Prune interval for the interface
Syntax:
JP Interval Value. Number range from=60 to=65520<60-65520>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim jp-interval <NUMBER>
ip pim jp-interval <NUMBER>
Description: Configures the Join-Prune interval for the interface
Syntax:
JP Interval Value. Number range from=60 to=65520<60-65520>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)618
I Commandsip pim jp-interval
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip pim jp-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 619
I Commandsip pim jp-interval
ip pim jp-policyip pim jp-policy <WORD> in|out
Description: Specify policy for receiving Join-Prune messages
Syntax:
pimpim
Route-map nameWORD
inin
outout
Command Mode: template ip pim interface-policy : Create a PIM interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip pim interface-policy <WORD>(config-tenant-template-ip-pim)# ip pim jp-policy <WORD> in|out
ip pim jp-policy <WORD> in|out
Description: Specify policy for receiving Join-Prune messages
Syntax:
Route-map nameWORD
inin
outout
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim jp-policy <WORD> in|out
ip pim jp-policy <WORD> in|out
Description: Specify policy for receiving Join-Prune messages
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)620
I Commandsip pim jp-policy
Route-map nameWORD
inin
outout
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip pim jp-policy <WORD> in|out
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 621
I Commandsip pim jp-policy
ip pim mtuip pim mtu <NUMBER>
Description: Set PIM MTU size
Syntax:
MTU size in bytes. Number range from=1500 to=65536<1500-65536>
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim mtu <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)622
I Commandsip pim mtu
ip pim neighbor-policyip pim neighbor-policy <WORD>
Description: Configures a neighbor policy for filtering adjacencies
Syntax:
pimpim
Route-map nameWORD
Command Mode: template ip pim interface-policy : Create a PIM interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip pim interface-policy <WORD>(config-tenant-template-ip-pim)# ip pim neighbor-policy <WORD>
ip pim neighbor-policy <WORD>
Description: Configures a neighbor policy for filtering adjacencies
Syntax:
Route-map nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim neighbor-policy <WORD>
ip pim neighbor-policy <WORD>
Description: Configures a neighbor policy for filtering adjacencies
Syntax:
Route-map nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 623
I Commandsip pim neighbor-policy
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip pim neighbor-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)624
I Commandsip pim neighbor-policy
ip pim passiveip pim passive
Description: Configures interface to be a passive interface
Syntax:
pimpim
Command Mode: template ip pim interface-policy : Create a PIM interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip pim interface-policy <WORD>(config-tenant-template-ip-pim)# ip pim passive
ip pim passive
Description: Configures interface to be a passive interface
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim passive
ip pim passive
Description: Configures interface to be a passive interface
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip pim passive
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 625
I Commandsip pim passive
ip pim register-rate-limitip pim register-rate-limit <NUMBER>
Description: Rate limit for PIM data registers
Syntax:
Max number of packets per second. Number range from=1 to=65535<1-65535>
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim register-rate-limit <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)626
I Commandsip pim register-rate-limit
ip pim register-sourceip pim register-source <A.B.C.D>
Description: Configure source address for Register messages
Syntax:
Source IP address in format A.B.C.DA.B.C.D
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim register-source <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 627
I Commandsip pim register-source
ip pim rp-addressip pim rp-address <A.B.C.D> [route-map <WORD>]
Description: Configure static RP for group range
Syntax:
IP address in format A.B.C.DA.B.C.D
(Optional) route-map nameWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim rp-address <A.B.C.D> [route-map <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)628
I Commandsip pim rp-address
ip pim sg-expiry-timerip pim sg-expiry-timer <NUMBER> [sg-list <WORD>]
Description: Adjust expiry time for PIM ASM (S,G) routes
Syntax:
Expiry timer interval in seconds. Number range from=180 to=604801<180-604801>
(Optional) Route-map nameWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim sg-expiry-timer <NUMBER> [sg-list <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 629
I Commandsip pim sg-expiry-timer
ip pim sparseip pim sparse
Description: Enable PIM on this interface
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim sparse
ip pim sparse
Description: Enable PIM on this interface
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip pim sparse
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)630
I Commandsip pim sparse
ip pim ssm route-mapip pim ssm route-map <WORD>
Description: Associate route-map policy for SSM range
Syntax:
Route-map nameWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim ssm route-map <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 631
I Commandsip pim ssm route-map
ip pim state-limitip pim state-limit <NUMBER>
Description: Configure maximum state entries
Syntax:
Maximum state entries. Number range from=1 to=4294967295<1-4294967295>
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim state-limit <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)632
I Commandsip pim state-limit
ip pim state-limit reservedip pim state-limit <NUMBER> reserved <WORD> <NUMBER>
Description: Configure maximum state entries
Syntax:
Maximum state entries. Number range from=1 to=4294967295<1-4294967295>
route-map nameWORD
Maximum reserve state entries. Number range from=0 to=4294967295<0-4294967295>
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim state-limit <NUMBER> reserved <WORD> <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 633
I Commandsip pim state-limit reserved
ip pim strict-rfc-compliantip pim strict-rfc-compliant
Description: Set PIM RFC Compliant
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim strict-rfc-compliant
ip pim strict-rfc-compliant
Description: Set PIM RFC Compliant
Syntax:
pimpim
Command Mode: template ip pim interface-policy : Create a PIM interface policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip pim interface-policy <WORD>(config-tenant-template-ip-pim)# ip pim strict-rfc-compliant
ip pim strict-rfc-compliant
Description: Set PIM RFC Compliant
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip pim strict-rfc-compliant
ip pim strict-rfc-compliant
Description: Set PIM RFC Compliant
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)634
I Commandsip pim strict-rfc-compliant
(config-leaf-if)# ip pim strict-rfc-compliant
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 635
I Commandsip pim strict-rfc-compliant
ip pim use-shared-tree-onlyip pim use-shared-tree-only group-list <WORD>
Description: Use (*,G) only state, no source state is created
Syntax:
group listgroup-list
Route-map nameWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# ip pim use-shared-tree-only group-list <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)636
I Commandsip pim use-shared-tree-only
ip prefix-listip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN>
Description: Build a prefix-list
Syntax:
Name of prefix-list (Max Size 64)WORD
Specify routes to forwardpermit
IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# ip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN>
ip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN>
Description: Build a prefix-list
Syntax:
Name of prefix-list (Max Size 64)WORD
Specify routes to forwardpermit
IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# ip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 637
I Commandsip prefix-list
ip prefix-list permit leip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN> le <32>
Description:Maximum prefix length to be matched
Syntax:
Name of prefix-list (Max Size 64)WORD
Specify routes to forwardpermit
IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN
Maximum prefix length32
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# ip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN> le<32>
ip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN> le <32>
Description:Maximum prefix length to be matched
Syntax:
Name of prefix-list (Max Size 64)WORD
Specify routes to forwardpermit
IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN
Maximum prefix length32
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# ip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN> le<32>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)638
I Commandsip prefix-list permit le
ip prefixip prefix permit <A.B.C.D/LEN | A:B::C:D/LEN>
Description: IP prefix for route match
Syntax:
Specify routes to forwardpermit
IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route group <WORD> tenant <WORD>(config-route-group)# ip prefix permit <A.B.C.D/LEN | A:B::C:D/LEN>
ip prefix permit <A.B.C.D/LEN | A:B::C:D/LEN>
Description: IP prefix for route match
Syntax:
Specify routes to forwardpermit
IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route group <WORD> tenant <WORD>(config-route-group)# ip prefix permit <A.B.C.D/LEN | A:B::C:D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 639
I Commandsip prefix
ip prefix permit leip prefix permit <A.B.C.D/LEN | A:B::C:D/LEN> le <32>
Description:Maximum prefix length to be matched
Syntax:
Specify routes to forwardpermit
IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN
Maximum prefix length32
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route group <WORD> tenant <WORD>(config-route-group)# ip prefix permit <A.B.C.D/LEN | A:B::C:D/LEN> le <32>
ip prefix permit <A.B.C.D/LEN | A:B::C:D/LEN> le <32>
Description:Maximum prefix length to be matched
Syntax:
Specify routes to forwardpermit
IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN
Maximum prefix length32
Command Mode: template route group : Configure Route Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route group <WORD> tenant <WORD>(config-route-group)# ip prefix permit <A.B.C.D/LEN | A:B::C:D/LEN> le <32>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)640
I Commandsip prefix permit le
ip router eigrpip router eigrp default
Description: Configure Router EIGRP Policies
Syntax:
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip router eigrp default
ip router eigrp default
Description: Configure EIGRP default interface
Syntax:
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip router eigrp default
ip router eigrp default
Description: Configure Router EIGRP Policies
Syntax:
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 641
I Commandsip router eigrp
(config-leaf-if)# ip router eigrp default
ip router eigrp default
Description: Configure EIGRP default interface
Syntax:
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip router eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)642
I Commandsip router eigrp
ip router ospf defaultip router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip router ospf default area <A.B.C.D|NUMBER>
ip router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip router ospf default area <A.B.C.D|NUMBER>
ip router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 643
I Commandsip router ospf default
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip router ospf default area <A.B.C.D|NUMBER>
ip router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip router ospf default area <A.B.C.D|NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)644
I Commandsip router ospf default
ip shared address consumerip shared address <A.B.C.D/LEN> consumer application any epg any
Description: Shared consumed service
Syntax:
IPv4 subnetaddress
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
application keywordapplication
any applicationany
epg keywordepg
any EPGany
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip shared address <A.B.C.D/LEN> consumer application any epg any
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 645
I Commandsip shared address consumer
ip shared address providerip shared address <A.B.C.D/LEN> provider application <WORD> epg <WORD> [scope <scope>]
Description: Shared provider service
Syntax:
IPv4 subnetaddress
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
application keywordapplication
Application Name (Max Size 64)WORD
epg keywordepg
Application EPG (Max Size 64)WORD
(Optional) Scope of the address among ['public']scope
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip shared address <A.B.C.D/LEN> provider application <WORD> epg<WORD> [scope <scope>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)646
I Commandsip shared address provider
ip split-horizonip split-horizon eigrp default
Description: Set the split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip split-horizon eigrp default
ip split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip split-horizon eigrp default
ip split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 647
I Commandsip split-horizon
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip split-horizon eigrp default
ip split-horizon eigrp default
Description: Set the split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip split-horizon eigrp default
ip split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip split-horizon eigrp default
ip split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)648
I Commandsip split-horizon
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip split-horizon eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 649
I Commandsip split-horizon
ip summary-address eigrpip summary-address eigrp default <IP-PREFIX/LEN>
Description: Configure route summarization for EIGRP
Syntax:
EIGRP default instancedefault
Summary IPV4 address (e.g. 10.0.0.0/8)IP-PREFIX/LEN
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip summary-address eigrp default <IP-PREFIX/LEN>
ip summary-address eigrp default <IP-PREFIX/LEN>
Description: Configure route summarization for EIGRP
Syntax:
EIGRP default instancedefault
Summary IPV4 address (e.g. 10.0.0.0/8)IP-PREFIX/LEN
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip summary-address eigrp default <IP-PREFIX/LEN>
ip summary-address eigrp default <IP-PREFIX/LEN>
Description: Configure route summarization for EIGRP
Syntax:
EIGRP default instancedefault
Summary IPV4 address (e.g. 10.0.0.0/8)IP-PREFIX/LEN
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)650
I Commandsip summary-address eigrp
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip summary-address eigrp default <IP-PREFIX/LEN>
ip summary-address eigrp default <IP-PREFIX/LEN>
Description: Configure route summarization for EIGRP
Syntax:
EIGRP default instancedefault
Summary IPV4 address (e.g. 10.0.0.0/8)IP-PREFIX/LEN
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip summary-address eigrp default <IP-PREFIX/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 651
I Commandsip summary-address eigrp
ip throughput-delayip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughput delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughput delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)652
I Commandsip throughput-delay
(config-leaf-if)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughput delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughput delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 653
I Commandsip throughput-delay
ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughput delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughput delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)654
I Commandsip throughput-delay
ip ttlip ttl <ttl>
Description: TTL
Syntax:
ttl value. Number range from=1 to=255ttl
Command Mode: destination tenant : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# ip ttl <ttl>
ip ttl <ttl>
Description: TTL
Syntax:
ttl value. Number range from=1 to=255ttl
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# ip ttl <ttl>
ip ttl <arg>
Description: TTL
Syntax:
ttl value. Number range from=1 to=255arg
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 655
I Commandsip ttl
(config)# monitor tenant <tenant_name> session <WORD>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-tenant-dest)# ip ttl <>
ip ttl <arg>
Description: Configure TTL
Syntax:
TTL value. Number range from=1 to=255arg
Command Mode: destination destip : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# ip ttl <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)656
I Commandsip ttl
ipobtainmodeipobtainmode learn|admin|autoconfig
Description:Mode to obtain Virtual IP Address
Syntax:
learn IP from HSRP peerlearn
Address is configuredadmin
Auto configure ipv6 addressautoconfig
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# ipobtainmode learn|admin|autoconfig
ipobtainmode learn|admin|autoconfig
Description:Mode to obtain Virtual IP Address
Syntax:
learn IP from HSRP peerlearn
Address is configuredadmin
Auto configure ipv6 addressautoconfig
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# ipobtainmode learn|admin|autoconfig
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 657
I Commandsipobtainmode
iprangeiprange <startip> <endip>
Description: Add ip pool
Syntax:
startipstartip
endipendip
Command Mode: microsoft : Configure static IP pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# iprange <startip> <endip>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)658
I Commandsiprange
ipv6-routeripv6-router
Description: Config IPv6 router in trust control policy
Command Mode: trust-control : Configuration for trust control policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# trust-control <WORD>(config-tenant-fhs-trustctrl)# ipv6-router
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 659
I Commandsipv6-router
ipv6ipv6 route <A:B::C:D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
Description: Configure IPv6 features
Syntax:
Configure IPv6 unicast static routeroute
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
ipAddress|null
<ZeroorPref>
<BfdorPref>
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# ipv6 route <A:B::C:D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
ipv6 route <A:B::C:D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
Description: Configure IPv6 features
Syntax:
Configure IPv6 unicast static routeroute
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
ipAddress|null
<ZeroorPref>
<BfdorPref>
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)660
I Commandsipv6
(config-leaf-vrf)# ipv6 route <A:B::C:D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 661
I Commandsipv6
ipv6 address-rangeipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
Description: Configure IPv6 Address Range
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C:X
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
Description: Configure IPv6 Address Range
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C:X
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
Description: Configure IPv6 Address Range
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)662
I Commandsipv6 address-range
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C:X
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
Description: Configure IPv6 Address Range
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C:X
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 663
I Commandsipv6 address-range
ipv6 addressipv6 address <A:B::C:D/LEN> [scope <scope>] [preferred] [suppress-nd] [eui64]
Description: Define an IPv6 subnet to be exported by the BD
Syntax:
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
(Optional) Scope of the address among ['public', 'private']scope
(Optional) Set the address as preferred addresspreferred
(Optional) Suppress the Neighbor Discovery on this subnetsuppress-nd
(Optional) Use eui64 interface identifiereui64
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 address <A:B::C:D/LEN> [scope <scope>] [preferred][suppress-nd] [eui64]
ipv6 address <A:B::C:D/LEN> eui64 [preferred]
Description: Configure IPv6 address on interface
Syntax:
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
Configure Extended Unique Identifier for the low-order 64 bitseui64
(Optional) Configure IPv6 address as preferredpreferred
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 address <A:B::C:D/LEN> eui64 [preferred]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)664
I Commandsipv6 address
ipv6 address <A:B::C:D/LEN> eui64 [preferred]
Description: Configure IPv6 address on interface
Syntax:
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
Configure Extended Unique Identifier for the low-order 64 bitseui64
(Optional) Configure IPv6 address as preferredpreferred
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 address <A:B::C:D/LEN> eui64 [preferred]
ipv6 address <A:B::C:D/LEN> eui64 [preferred]
Description: Configure IPv6 address on interface
Syntax:
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
Configure Extended Unique Identifier for the low-order 64 bitseui64
(Optional) Configure IPv6 address as preferredpreferred
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 address <A:B::C:D/LEN> eui64 [preferred]
ipv6 address <A:B::C:D/LEN> eui64 [preferred]
Description: Configure IPv6 address on interface
Syntax:
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
Configure Extended Unique Identifier for the low-order 64 bitseui64
(Optional) Configure IPv6 address as preferredpreferred
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 665
I Commandsipv6 address
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 address <A:B::C:D/LEN> eui64 [preferred]
ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
Description: Configure IP and gateway features
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C::X
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
Description: Configure IPv6 Address and Gateway
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C::X
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)666
I Commandsipv6 address
ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
Description: Configure IP and gateway features
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C::X
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
Description: Configure IPv6 Address and Gateway
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C::X
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 667
I Commandsipv6 address
ipv6 address tenant applicationipv6 address <A:B::C:D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> application <WORD> epg<WORD>
ipv6 address <A:B::C:D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)668
I Commandsipv6 address tenant application
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> application<WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 669
I Commandsipv6 address tenant application
ipv6 address tenant external-l2ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>
ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)670
I Commandsipv6 address tenant external-l2
<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 671
I Commandsipv6 address tenant external-l2
ipv6 address tenant external-l3ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>
ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)672
I Commandsipv6 address tenant external-l3
<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 673
I Commandsipv6 address tenant external-l3
ipv6 bandwidthipv6 bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 bandwidth eigrp default <NUMBER>
ipv6 bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 bandwidth eigrp default <NUMBER>
ipv6 bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)674
I Commandsipv6 bandwidth
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 bandwidth eigrp default <NUMBER>
ipv6 bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 bandwidth eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 675
I Commandsipv6 bandwidth
ipv6 bfdipv6 bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 bfd eigrp enable
ipv6 bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 bfd eigrp enable
ipv6 bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)676
I Commandsipv6 bfd
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 bfd eigrp enable
ipv6 bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 bfd eigrp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 677
I Commandsipv6 bfd
ipv6 dhcp relay address tenant applicationipv6 dhcp relay address <A:B::C:D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 dhcp relay address <A:B::C:D> tenant <WORD> application<WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)678
I Commandsipv6 dhcp relay address tenant application
ipv6 dhcp relay address tenant external-l2ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l2 epg<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 679
I Commandsipv6 dhcp relay address tenant external-l2
ipv6 dhcp relay address tenant external-l3ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l3 epg<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)680
I Commandsipv6 dhcp relay address tenant external-l3
ipv6 distribute-list eigrpipv6 distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP route-map
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 distribute-list eigrp default route-map <WORD> out
ipv6 distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP Policies
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 distribute-list eigrp default route-map <WORD> out
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 681
I Commandsipv6 distribute-list eigrp
ipv6 distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP route-map
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 distribute-list eigrp default route-map <WORD> out
ipv6 distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP Policies
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 distribute-list eigrp default route-map <WORD> out
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)682
I Commandsipv6 distribute-list eigrp
ipv6 flowipv6 flow monitor <WORD>
Description: Configure Netflow on the Policy Group
Syntax:
Configure Netflow on the Policy Groupmonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# ipv6 flow monitor <WORD>
ipv6 flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# ipv6 flow monitor <WORD>
ipv6 flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 683
I Commandsipv6 flow
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 flow monitor <WORD>
ipv6 flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 flow monitor <WORD>
ipv6 flow monitor <arg>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 flow monitor <>
ipv6 flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)684
I Commandsipv6 flow
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# ipv6 flow monitor <WORD>
ipv6 flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 flow monitor <WORD>
ipv6 flow monitor <arg>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 flow monitor <>
ipv6 flow monitor <WORD>
Description: Configure Netflow on the Interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 685
I Commandsipv6 flow
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# ipv6 flow monitor <WORD>
ipv6 flow monitor <WORD>
Description: Configure Netflow on the VPC
Syntax:
Configure Netflow on the VPCmonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# ipv6 flow monitor <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)686
I Commandsipv6 flow
ipv6 hello-intervalipv6 hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 hello-interval eigrp default <NUMBER>
ipv6 hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 hello-interval eigrp default <NUMBER>
ipv6 hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 687
I Commandsipv6 hello-interval
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 hello-interval eigrp default <NUMBER>
ipv6 hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 hello-interval eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)688
I Commandsipv6 hello-interval
ipv6 hold-intervalipv6 hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 hold-interval eigrp default <NUMBER>
ipv6 hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 hold-interval eigrp default <NUMBER>
ipv6 hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 689
I Commandsipv6 hold-interval
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 hold-interval eigrp default <NUMBER>
ipv6 hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 hold-interval eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)690
I Commandsipv6 hold-interval
ipv6 link-localipv6 link-local <A:B::C:D>
Description: Configure IPv6 link-local address
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 link-local <A:B::C:D>
ipv6 link-local <X:X:X:X::X>
Description: Configure IPv6 link-local address
Syntax:
IPv6 link-local addressX:X:X:X::X
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 link-local <X:X:X:X::X>
ipv6 link-local <X:X:X:X::X>
Description: Configure IPv6 link-local address
Syntax:
IPv6 link-local addressX:X:X:X::X
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 691
I Commandsipv6 link-local
(config-leaf-if)# ipv6 link-local <X:X:X:X::X>
ipv6 link-local <X:X:X:X::X>
Description: Configure IPv6 link-local address
Syntax:
IPv6 link-local addressX:X:X:X::X
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 link-local <X:X:X:X::X>
ipv6 link-local <X:X:X:X::X>
Description: Configure IPv6 link-local address
Syntax:
IPv6 link-local addressX:X:X:X::X
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 link-local <X:X:X:X::X>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)692
I Commandsipv6 link-local
ipv6 nd hop-limitipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd hop-limit <NUMBER>
ipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd hop-limit <NUMBER>
ipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 693
I Commandsipv6 nd hop-limit
(config-template-nd-pol)# ipv6 nd hop-limit <NUMBER>
ipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd hop-limit <NUMBER>
ipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd hop-limit <NUMBER>
ipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd hop-limit <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)694
I Commandsipv6 nd hop-limit
ipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd hop-limit <NUMBER>
ipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd hop-limit <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 695
I Commandsipv6 nd hop-limit
ipv6 nd managed-config-flagipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd managed-config-flag
ipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd managed-config-flag
ipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd managed-config-flag
ipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd managed-config-flag
ipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)696
I Commandsipv6 nd managed-config-flag
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd managed-config-flag
ipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd managed-config-flag
ipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd managed-config-flag
ipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd managed-config-flag
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 697
I Commandsipv6 nd managed-config-flag
ipv6 nd mtuipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd mtu <NUMBER>
ipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd mtu <NUMBER>
ipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)698
I Commandsipv6 nd mtu
(config-template-nd-pol)# ipv6 nd mtu <NUMBER>
ipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd mtu <NUMBER>
ipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd mtu <NUMBER>
ipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd mtu <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 699
I Commandsipv6 nd mtu
ipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd mtu <NUMBER>
ipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd mtu <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)700
I Commandsipv6 nd mtu
ipv6 nd ns-intervalipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ns-interval <NUMBER>
ipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ns-interval <NUMBER>
ipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 701
I Commandsipv6 nd ns-interval
(config-template-nd-pol)# ipv6 nd ns-interval <NUMBER>
ipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ns-interval <NUMBER>
ipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ns-interval <NUMBER>
ipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd ns-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)702
I Commandsipv6 nd ns-interval
ipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ns-interval <NUMBER>
ipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ns-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 703
I Commandsipv6 nd ns-interval
ipv6 nd ns-retriesipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ns-retries <NUMBER>
ipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ns-retries <NUMBER>
ipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)704
I Commandsipv6 nd ns-retries
(config-template-nd-pol)# ipv6 nd ns-retries <NUMBER>
ipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ns-retries <NUMBER>
ipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ns-retries <NUMBER>
ipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd ns-retries <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 705
I Commandsipv6 nd ns-retries
ipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ns-retries <NUMBER>
ipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ns-retries <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)706
I Commandsipv6 nd ns-retries
ipv6 nd other-config-flagipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd other-config-flag
ipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd other-config-flag
ipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd other-config-flag
ipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd other-config-flag
ipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 707
I Commandsipv6 nd other-config-flag
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd other-config-flag
ipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd other-config-flag
ipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd other-config-flag
ipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd other-config-flag
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)708
I Commandsipv6 nd other-config-flag
ipv6 nd policyipv6 nd policy <WORD>
Description: Associate the BD with an IPv6 Neighbor Discovery policy
Syntax:
Name of the policy to associate (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 709
I Commandsipv6 nd policy
ipv6 nd prefixipv6 nd prefix <A:B::C:D/LEN> <NUMBER> <NUMBER> [no-autoconfig] [no-onlink] [router-address]
Description: Advertise in Neighbor Discover a Prefix and configure the parameters
Syntax:
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
Lifetime to advertise for the prefix, in seconds. Number range from=0to=4294967295
<0-4294967295>
Preferred lifetime to advertise, in seconds. Number range from=0to=4294967295
<0-4294967295>
(Optional) advertise with A bit clearno-autoconfig
(Optional) advertise with L bit clearno-onlink
(Optional) Set this prefix as usable as default gateway by the hostsrouter-address
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd prefix <A:B::C:D/LEN> <NUMBER> <NUMBER> [no-autoconfig][no-onlink] [router-address]
ipv6 nd prefix <NUMBER> <NUMBER> [no-autoconfig] [no-onlink] [router-address]
Description: Advertise in Neighbor Discover a Prefix and configure the parameters
Syntax:
Lifetime to advertise for the prefix, in milliseconds. Number rangefrom=0 to=4294967295
<0-4294967295>
Preferred lifetime to advertise, in milliseconds. Number range from=0to=4294967295
<0-4294967295>
(Optional) advertise with A bit clearno-autoconfig
(Optional) advertise with L bit clearno-onlink
(Optional) Set this prefix as usable as default gateway by the hostsrouter-address
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)710
I Commandsipv6 nd prefix
Command Mode: template ipv6 nd prefix : Create/modify an an IPv6 Neighbor Prefix policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd prefix policy <WORD>(config-tenant-template-ipv6-nd-pfx)# ipv6 nd prefix <NUMBER> <NUMBER> [no-autoconfig][no-onlink] [router-address]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 711
I Commandsipv6 nd prefix
ipv6 nd ra-intervalipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ra-interval <NUMBER>
ipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ra-interval <NUMBER>
ipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)712
I Commandsipv6 nd ra-interval
(config-template-nd-pol)# ipv6 nd ra-interval <NUMBER>
ipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ra-interval <NUMBER>
ipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ra-interval <NUMBER>
ipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd ra-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 713
I Commandsipv6 nd ra-interval
ipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ra-interval <NUMBER>
ipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ra-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)714
I Commandsipv6 nd ra-interval
ipv6 nd ra-lifetimeipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ra-lifetime <NUMBER>
ipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ra-lifetime <NUMBER>
ipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 715
I Commandsipv6 nd ra-lifetime
(config-template-nd-pol)# ipv6 nd ra-lifetime <NUMBER>
ipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ra-lifetime <NUMBER>
ipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ra-lifetime <NUMBER>
ipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd ra-lifetime <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)716
I Commandsipv6 nd ra-lifetime
ipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ra-lifetime <NUMBER>
ipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ra-lifetime <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 717
I Commandsipv6 nd ra-lifetime
ipv6 nd reachable-timeipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Reachable timer in seconds. Number range from=0 to=3600000<0-3600000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd reachable-time <NUMBER>
ipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Reachable timer in milliseconds. Number range from=0 to=3600000<0-3600000>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd reachable-time <NUMBER>
ipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Reachable timer in milliseconds. Number range from=0 to=3600000<0-3600000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)718
I Commandsipv6 nd reachable-time
(config-template-nd-pol)# ipv6 nd reachable-time <NUMBER>
ipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Reachable timer in milliseconds. Number range from=0 to=3600000<0-3600000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd reachable-time <NUMBER>
ipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Reachable timer in milliseconds. Number range from=0 to=3600000<0-3600000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd reachable-time <NUMBER>
ipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Reachable timer in milliseconds. Number range from=0 to=3600000<0-3600000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd reachable-time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 719
I Commandsipv6 nd reachable-time
ipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Reachable timer in milliseconds. Number range from=0 to=3600000<0-3600000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd reachable-time <NUMBER>
ipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Reachable timer in milliseconds. Number range from=0 to=3600000<0-3600000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd reachable-time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)720
I Commandsipv6 nd reachable-time
ipv6 nd retrans-timeripv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Retransmit timer, in seconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd retrans-timer <NUMBER>
ipv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Retransmit timer inmilliseconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd retrans-timer <NUMBER>
ipv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Retransmit timer inmilliseconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 721
I Commandsipv6 nd retrans-timer
(config-template-nd-pol)# ipv6 nd retrans-timer <NUMBER>
ipv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Retransmit timer inmilliseconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd retrans-timer <NUMBER>
ipv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Retransmit timer inmilliseconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd retrans-timer <NUMBER>
ipv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Retransmit timer inmilliseconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd retrans-timer <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)722
I Commandsipv6 nd retrans-timer
ipv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Retransmit timer inmilliseconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd retrans-timer <NUMBER>
ipv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Retransmit timer inmilliseconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd retrans-timer <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 723
I Commandsipv6 nd retrans-timer
ipv6 nd suppress-ra-mtuipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd suppress-ra-mtu
ipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd suppress-ra-mtu
ipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd suppress-ra-mtu
ipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd suppress-ra-mtu
ipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)724
I Commandsipv6 nd suppress-ra-mtu
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd suppress-ra-mtu
ipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd suppress-ra-mtu
ipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd suppress-ra-mtu
ipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd suppress-ra-mtu
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 725
I Commandsipv6 nd suppress-ra-mtu
ipv6 nd suppress-raipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd suppress-ra
ipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd suppress-ra
ipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd suppress-ra
ipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd suppress-ra
ipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)726
I Commandsipv6 nd suppress-ra
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd suppress-ra
ipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd suppress-ra
ipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd suppress-ra
ipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd suppress-ra
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 727
I Commandsipv6 nd suppress-ra
ipv6 next-hop-selfipv6 next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 next-hop-self eigrp default
ipv6 next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 next-hop-self eigrp default
ipv6 next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)728
I Commandsipv6 next-hop-self
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 next-hop-self eigrp default
ipv6 next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 next-hop-self eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 729
I Commandsipv6 next-hop-self
ipv6 ospf bfdipv6 ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf bfd enable
ipv6 ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf bfd enable
ipv6 ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)730
I Commandsipv6 ospf bfd
(config-leaf-if)# ipv6 ospf bfd enable
ipv6 ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf bfd enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 731
I Commandsipv6 ospf bfd
ipv6 ospf costipv6 ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf cost <NUMBER>
ipv6 ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf cost <NUMBER>
ipv6 ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)732
I Commandsipv6 ospf cost
(config-leaf-if)# ipv6 ospf cost <NUMBER>
ipv6 ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf cost <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 733
I Commandsipv6 ospf cost
ipv6 ospf dead-intervalipv6 ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf dead-interval <NUMBER>
ipv6 ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf dead-interval <NUMBER>
ipv6 ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)734
I Commandsipv6 ospf dead-interval
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf dead-interval <NUMBER>
ipv6 ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf dead-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 735
I Commandsipv6 ospf dead-interval
ipv6 ospf hello-intervalipv6 ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf hello-interval <NUMBER>
ipv6 ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf hello-interval <NUMBER>
ipv6 ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)736
I Commandsipv6 ospf hello-interval
(config-leaf-if)# ipv6 ospf hello-interval <NUMBER>
ipv6 ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf hello-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 737
I Commandsipv6 ospf hello-interval
ipv6 ospf inheritipv6 ospf inherit interface-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf inherit interface-policy <WORD>
ipv6 ospf inherit interface-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf inherit interface-policy <WORD>
ipv6 ospf inherit interface-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)738
I Commandsipv6 ospf inherit
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf inherit interface-policy <WORD>
ipv6 ospf inherit interface-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf inherit interface-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 739
I Commandsipv6 ospf inherit
ipv6 ospf mtu-ignoreipv6 ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf mtu-ignore
ipv6 ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf mtu-ignore
ipv6 ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf mtu-ignore
ipv6 ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf mtu-ignore
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)740
I Commandsipv6 ospf mtu-ignore
ipv6 ospf networkipv6 ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf network bcast|p2p|unspecified
ipv6 ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf network bcast|p2p|unspecified
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 741
I Commandsipv6 ospf network
ipv6 ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf network bcast|p2p|unspecified
ipv6 ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf network bcast|p2p|unspecified
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)742
I Commandsipv6 ospf network
ipv6 ospf passive-interfaceipv6 ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf passive-interface
ipv6 ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf passive-interface
ipv6 ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf passive-interface
ipv6 ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf passive-interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 743
I Commandsipv6 ospf passive-interface
ipv6 ospf prefix-suppressionipv6 ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf prefix-suppression disable|enable|inherit
ipv6 ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf prefix-suppression disable|enable|inherit
ipv6 ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)744
I Commandsipv6 ospf prefix-suppression
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf prefix-suppression disable|enable|inherit
ipv6 ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf prefix-suppression disable|enable|inherit
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 745
I Commandsipv6 ospf prefix-suppression
ipv6 ospf priorityipv6 ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf priority <NUMBER>
ipv6 ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf priority <NUMBER>
ipv6 ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)746
I Commandsipv6 ospf priority
(config-leaf-if)# ipv6 ospf priority <NUMBER>
ipv6 ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf priority <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 747
I Commandsipv6 ospf priority
ipv6 ospf retransmit-intervalipv6 ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf retransmit-interval <NUMBER>
ipv6 ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf retransmit-interval <NUMBER>
ipv6 ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)748
I Commandsipv6 ospf retransmit-interval
(config-leaf-if)# ipv6 ospf retransmit-interval <NUMBER>
ipv6 ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf retransmit-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 749
I Commandsipv6 ospf retransmit-interval
ipv6 ospf transmit-delayipv6 ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf transmit-delay <NUMBER>
ipv6 ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf transmit-delay <NUMBER>
ipv6 ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)750
I Commandsipv6 ospf transmit-delay
(config-leaf-if)# ipv6 ospf transmit-delay <NUMBER>
ipv6 ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf transmit-delay <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 751
I Commandsipv6 ospf transmit-delay
ipv6 passive-interfaceipv6 passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 passive-interface eigrp default
ipv6 passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 passive-interface eigrp default
ipv6 passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)752
I Commandsipv6 passive-interface
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 passive-interface eigrp default
ipv6 passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 passive-interface eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 753
I Commandsipv6 passive-interface
ipv6 router eigrpipv6 router eigrp default
Description: Configure EIGRP default interface
Syntax:
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 router eigrp default
ipv6 router eigrp default
Description: Configure EIGRP default interface
Syntax:
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 router eigrp default
ipv6 router eigrp default
Description: Configure EIGRP default interface
Syntax:
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)754
I Commandsipv6 router eigrp
(config-leaf-if)# ipv6 router eigrp default
ipv6 router eigrp default
Description: Configure EIGRP default interface
Syntax:
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 router eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 755
I Commandsipv6 router eigrp
ipv6 router ospf defaultipv6 router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 router ospf default area <A.B.C.D|NUMBER>
ipv6 router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 router ospf default area <A.B.C.D|NUMBER>
ipv6 router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)756
I Commandsipv6 router ospf default
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 router ospf default area <A.B.C.D|NUMBER>
ipv6 router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 router ospf default area <A.B.C.D|NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 757
I Commandsipv6 router ospf default
ipv6 shared address consumeripv6 shared address <A:B::C:D/LEN> consumer application any epg any
Description: Shared consumed service
Syntax:
IPv6 subnetaddress
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
application keywordapplication
any applicationany
epg keywordepg
any EPGany
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 shared address <A:B::C:D/LEN> consumer application any epgany
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)758
I Commandsipv6 shared address consumer
ipv6 shared address provideripv6 shared address <A:B::C:D/LEN> provider application <WORD> epg <WORD> [scope <scope>]
Description: Shared provider service
Syntax:
IPv6 subnetaddress
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
application keywordapplication
Application Name (Max Size 64)WORD
epg keywordepg
Application EPG (Max Size 64)WORD
(Optional) Scope of the address among ['public']scope
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 shared address <A:B::C:D/LEN> provider application <WORD>epg <WORD> [scope <scope>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 759
I Commandsipv6 shared address provider
ipv6 split-horizonipv6 split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 split-horizon eigrp default
ipv6 split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 split-horizon eigrp default
ipv6 split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)760
I Commandsipv6 split-horizon
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 split-horizon eigrp default
ipv6 split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 split-horizon eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 761
I Commandsipv6 split-horizon
ipv6 summary-address eigrpipv6 summary-address eigrp default <IP-PREFIX/LEN>
Description: Configure route summarization for EIGRP
Syntax:
EIGRP default instancedefault
Summary IPV6 address (e.g. 2001:0DB8:0:1::/64)IP-PREFIX/LEN
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 summary-address eigrp default <IP-PREFIX/LEN>
ipv6 summary-address eigrp default <IP-PREFIX/LEN>
Description: Configure route summarization for EIGRP
Syntax:
EIGRP default instancedefault
Summarized IPV6 address (e.g. 2001:0DB8:0:1::/64)IP-PREFIX/LEN
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 summary-address eigrp default <IP-PREFIX/LEN>
ipv6 summary-address eigrp default <IP-PREFIX/LEN>
Description: Configure route summarization for EIGRP
Syntax:
EIGRP default instancedefault
Summary IPV6 address (e.g. 2001:0DB8:0:1::/64)IP-PREFIX/LEN
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)762
I Commandsipv6 summary-address eigrp
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 summary-address eigrp default <IP-PREFIX/LEN>
ipv6 summary-address eigrp default <IP-PREFIX/LEN>
Description: Configure route summarization for EIGRP
Syntax:
EIGRP default instancedefault
Summarized IPV6 address (e.g. 2001:0DB8:0:1::/64)IP-PREFIX/LEN
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 summary-address eigrp default <IP-PREFIX/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 763
I Commandsipv6 summary-address eigrp
ipv6 throughput-delayipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughput delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughput delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)764
I Commandsipv6 throughput-delay
(config-leaf-if)# ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughput delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughput delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 765
I Commandsipv6 throughput-delay
isisisis fabric
Description: Intermediate System to Intermediate System (IS-IS)
Syntax:
Fabric IS-IS configurationfabric
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# isis fabric
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)766
I Commandsisis
isolationisolation enforce
Description: Enable EPG isolation
Syntax:
Enable enforcing of policy-control rules (EPG isolation)enforce
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# isolation enforce
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 767
I Commandsisolation
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)768
I Commandsisolation
K Commands
• key, page 770
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 769
keykey
Description: LDAP server key for authentication
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# key
key
Description: RADIUS server key for authentication
Command Mode: radius-server host : RADIUS server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# key
key
Description: TACACS server key for authentication
Command Mode: tacacs-server host : TACACS+ server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# key
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)770
K Commandskey
L Commands
• l2-unknown-unicast, page 774
• l2protocol-tunnel, page 775
• l3-unknown-multicast, page 776
• l3out, page 777
• l4l7-cluster, page 778
• l4l7-peer, page 779
• l4l7, page 780
• l4l7 cluster import-from, page 781
• l4l7 cluster name, page 782
• l4l7 graph, page 783
• l4l7 resource-pool, page 784
• label, page 785
• label match, page 786
• label name, page 787
• lacp fast-select-hot-standby, page 788
• lacp graceful-convergence, page 789
• lacp load-defer, page 790
• lacp max-links, page 791
• lacp min-links, page 793
• lacp port-priority, page 795
• lacp port-priority interface, page 797
• lacp rate, page 798
• lacp rate fast normal interface, page 800
• lacp suspend-individual, page 801
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 771
• lacp symmetric-hash, page 802
• last-name, page 803
• latency, page 804
• layer2-switched flow, page 805
• ldap-server attribute, page 809
• ldap-server basedn, page 810
• ldap-server filter, page 811
• ldap-server host, page 812
• ldap-server retries, page 813
• ldap-server timeout, page 814
• leaf-group, page 815
• leaf-interface-group, page 816
• leaf-interface-profile, page 817
• leaf-policy-group, page 819
• leaf-profile, page 820
• leaf, page 821
• legacy, page 823
• link, page 824
• lldp, page 828
• lldp holdtime, page 832
• lldp reinit, page 833
• lldp timer, page 834
• load-balance, page 835
• local-as, page 837
• locality, page 839
• logfile, page 840
• logging, page 841
• logging audit, page 842
• logging description, page 843
• logging event, page 844
• logging fault, page 845
• logging server-group, page 846
• logging session, page 847
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)772
L Commands
• logging severity, page 848
• logit, page 850
• logit severity dest-grp server node, page 851
• lsp-fast-flood, page 852
• lsp-gen-interval, page 853
• lsp-mtu, page 854
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 773
L Commands
l2-unknown-unicastl2-unknown-unicast <WORD>
Description: Change Unknown Unicast flood behavior
Syntax:
Unicast Unknown threatmentWORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# l2-unknown-unicast <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)774
L Commandsl2-unknown-unicast
l2protocol-tunnell2protocol-tunnel stp|lldp|cdp|lacp|vtp
Description: set the type of qinq tunneling protocol
Syntax:
Set protocol which needs to be tunnled to STPstp
Set protocol which needs to be tunnled to LLDPlldp
Set protocol which needs to be tunnled to CDPcdp
Set protocol which needs to be tunnled to LACPlacp
Set protocol which needs to be tunnled to VTPvtp
Command Mode: dot1q-tunnel : Tunnel configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# dot1q-tunnel <WORD>(config-tenant-tunnel)#l2protocol-tunnel stp|lldp|cdp|lacp|vtp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 775
L Commandsl2protocol-tunnel
l3-unknown-multicastl3-unknown-multicast <WORD>
Description: Change L3 Multicast flood behavior
Syntax:
IP Multicast unknown Fram handlingWORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# l3-unknown-multicast <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)776
L Commandsl3-unknown-multicast
l3outl3out <WORD>
Description: Configuration for L3Out
Syntax:
L3Out name (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l3out <WORD>
l3out <l3out> <default>
Description: Add l3out to the Resource Pool
Syntax:
l3outl3out
defaultdefault
Command Mode: l4l7 resource-pool : Configure L4-L7 Service Resource Pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 resource-pool <WORD>(config-resource-pool)# l3out <l3out> <default>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 777
L Commandsl3out
l4l7-clusterl4l7-cluster <ldevVip>
Description: Add ldev to the Resource Pool
Syntax:
ldevVipldevVip
Command Mode: l4l7 resource-pool : Configure L4-L7 Service Resource Pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 resource-pool <WORD>(config-resource-pool)# l4l7-cluster <ldevVip>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)778
L Commandsl4l7-cluster
l4l7-peerl4l7-peer tenant <WORD> out <WORD> epg <WORD> redistribute WORD
Description: Configure l3external epg association for a L4-L7 graph connector.
Syntax:
tenant under which the l3external epg residestenant
WORDWORD
l3external outside nameout
WORDWORD
l3external-epg nameepg
WORDWORD
Protocol Redistribute Settingsredistribute
Protocol Redistribute SettingsWORD
Command Mode: connector : Configure Connector for a Service Node
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>] [svcredir <Service Redirection>] [service-type <Service Type>](config-service)# connector <WORD> [cluster-interface <WORD>](config-connector)# l4l7-peer tenant <WORD> out <WORD> epg <WORD> redistribute WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 779
L Commandsl4l7-peer
l4l7l4l7 graph <WORD>
Description: Associate a l4l7 graph with this subject
Syntax:
l4l7 graph to associate withgraph
Service Graph name (Max Size 64)WORD
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# l4l7 graph <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)780
L Commandsl4l7
l4l7 cluster import-froml4l7 cluster import-from <WORD> device-cluster <WORD>
Description: Import a L4-L7 Service Device Cluster
Syntax:
Tenant name (Max Size 63)WORD
Device Cluster namedevice-cluster
Device cluster name (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster import-from <WORD> device-cluster <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 781
L Commandsl4l7 cluster import-from
l4l7 cluster namel4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service <service>] [function <function>][context <context>] [trunking <enable|disable>]
Description: Add a L4-L7 Service Device Cluster
Syntax:
Device cluster name (Max Size 64)WORD
Type of l4l7 Device Clustertype
Type of l4l7 Device Clustertype
Physical or Virtual vlan domain to use for allocating encapsvlan-domain
Physical Or Virtual vlan domain to use for allocating encaps<domain-name>
(Optional) Indicates the type of service the device cluster providesservice
(Optional) Indicates the type of function the device cluster providesfunction
(Optional) Type of l4l7 Device Contextcontext
(Optional) Enable or disable trunking for the device cluster<enable|disable>
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>] [context <context>] [trunking <enable|disable>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)782
L Commandsl4l7 cluster name
l4l7 graphl4l7 graph <WORD> [contract <contract-option>]
Description: Configure L4-L7 Service Graph
Syntax:
Service Graph name (Max Size 64)WORD
(Optional) Name of Contractcontract-option
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 783
L Commandsl4l7 graph
l4l7 resource-pooll4l7 resource-pool <WORD>
Description: Configure L4-L7 Service Resource Pool
Syntax:
WORDWORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 resource-pool <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)784
L Commandsl4l7 resource-pool
labellabel <WORD>
Description: Create Provider Label
Syntax:
Provider Label NameWORD
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# label <WORD>
label <WORD>
Description: Create Provider Label
Syntax:
Provider Label NameWORD
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# label <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 785
L Commandslabel
label matchlabel match provider|consumer any|one|all|none
Description: Specify the match type for the provider or consumer label
Syntax:
Matching type for providerprovider
Matching type for consumerconsumer
Match if ANY label is found in the contract relationany
Match if exactly ONE label is found in the contract relationone
Match if ALL labels are found in the contract relationall
Match if NO labels are found in the contract relationnone
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# label match provider|consumer any|one|all|none
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)786
L Commandslabel match
label namelabel name <WORD> provider|consumer
Description: Add a provider or consumer label to the subject
Syntax:
Name of the label to add (Max Size 64)WORD
Matching type for providerprovider
Matching type for consumerconsumer
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# label name <WORD> provider|consumer
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 787
L Commandslabel name
lacp fast-select-hot-standbylacp fast-select-hot-standby
Description: Enable LACP fast select for hot standby ports
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# lacp fast-select-hot-standby
lacp fast-select-hot-standby
Description: Enable LACP fast select for hot standby ports
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp fast-select-hot-standby
lacp fast-select-hot-standby
Description: Enable LACP fast select for hot standby ports
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp fast-select-hot-standby
lacp fast-select-hot-standby
Description: Enable LACP fast select for hot standby ports
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp fast-select-hot-standby
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)788
L Commandslacp fast-select-hot-standby
lacp graceful-convergencelacp graceful-convergence
Description: Enable LACP graceful convergence
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# lacp graceful-convergence
lacp graceful-convergence
Description: Enable LACP graceful convergence
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp graceful-convergence
lacp graceful-convergence
Description: Enable LACP graceful convergence
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp graceful-convergence
lacp graceful-convergence
Description: Enable LACP graceful convergence
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp graceful-convergence
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 789
L Commandslacp graceful-convergence
lacp load-deferlacp load-defer
Description: Enable LACP load defer member ports
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# lacp load-defer
lacp load-defer
Description: Enable LACP load defer member ports
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp load-defer
lacp load-defer
Description: Enable LACP load defer member ports
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp load-defer
lacp load-defer
Description: Enable LACP load defer member ports
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp load-defer
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)790
L Commandslacp load-defer
lacp max-linkslacp max-links <NUMBER>
Description: Configure maximum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# lacp max-links <NUMBER>
lacp max-links <NUMBER>
Description: Configure maximum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp max-links <NUMBER>
lacp max-links <NUMBER>
Description: Configure maximum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 791
L Commandslacp max-links
(config-leaf-if)# lacp max-links <NUMBER>
lacp max-links <NUMBER>
Description: Configure maximum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp max-links <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)792
L Commandslacp max-links
lacp min-linkslacp min-links <NUMBER>
Description: Configure minimum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# lacp min-links <NUMBER>
lacp min-links <NUMBER>
Description: Configure minimum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp min-links <NUMBER>
lacp min-links <NUMBER>
Description: Configure minimum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 793
L Commandslacp min-links
(config-leaf-if)# lacp min-links <NUMBER>
lacp min-links <NUMBER>
Description: Configure minimum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp min-links <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)794
L Commandslacp min-links
lacp port-prioritylacp port-priority <arg>
Description: Set Lacp priority
Syntax:
Priority Value. Number range from=1 to=65535arg
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp port-priority <>
lacp port-priority <arg>
Description: Set Lacp priority.
Syntax:
Priority Value. Number range from=1 to=65535arg
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp port-priority <>
lacp port-priority <NUMBER>
Description: Set Lacp priority.
Syntax:
Priority Value. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 795
L Commandslacp port-priority
(config-leaf-if)# lacp port-priority <NUMBER>
lacp port-priority <NUMBER>
Description: Set Lacp priority.
Syntax:
Priority Value. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# lacp port-priority <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)796
L Commandslacp port-priority
lacp port-priority interfacelacp port-priority <arg> interface ethernet
Description: Set Port Priority on specific Ports
Syntax:
Priority Value. Number range from=1 to=65535arg
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp port-priority <> interface ethernet
lacp port-priority <arg> interface ethernet
Description: Set Port Priority on specific ports
Syntax:
Priority Value. Number range from=1 to=65535arg
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp port-priority <> interface ethernet
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 797
L Commandslacp port-priority interface
lacp ratelacp rate fast|normal
Description: Set Lacp rate
Syntax:
Set rate to fastfast
Set rate to normalnormal
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp rate fast|normal
lacp rate fast|normal
Description: Set Lacp rate
Syntax:
Set rate to fastfast
Set rate to normalnormal
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp rate fast|normal
lacp rate fast|normal
Description: Set Lacp rate
Syntax:
Set rate to fastfast
Set rate to normalnormal
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)798
L Commandslacp rate
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# lacp rate fast|normal
lacp rate fast|normal
Description: Set Lacp rate
Syntax:
Set rate to fastfast
Set rate to normalnormal
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# lacp rate fast|normal
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 799
L Commandslacp rate
lacp rate fast normal interfacelacp rate fast|normal interface ethernet
Description: Set Port Priority on specific Ports
Syntax:
Set rate to fastfast
Set rate to normalnormal
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp rate fast|normal interface ethernet
lacp rate fast|normal interface ethernet
Description: Set Port Priority on specific Ports
Syntax:
Set rate to fastfast
Set rate to normalnormal
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp rate fast|normal interface ethernet
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)800
L Commandslacp rate fast normal interface
lacp suspend-individuallacp suspend-individual
Description: Enable LACP individual Port suspension
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# lacp suspend-individual
lacp suspend-individual
Description: Enable LACP individual Port suspension
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp suspend-individual
lacp suspend-individual
Description: Enable LACP individual Port suspension
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp suspend-individual
lacp suspend-individual
Description: Enable LACP individual Port suspension
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp suspend-individual
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 801
L Commandslacp suspend-individual
lacp symmetric-hashlacp symmetric-hash
Description: Configure symmetric hashing policy
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# lacp symmetric-hash
lacp symmetric-hash
Description: Configure symmetric hashing policy
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp symmetric-hash
lacp symmetric-hash
Description: Configure symmetric hashing policy
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp symmetric-hash
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)802
L Commandslacp symmetric-hash
last-namelast-name <WORD>
Description: Set The last name of the locally-authenticated user.
Syntax:
last name (Max Size 32)WORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# last-name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 803
L Commandslast-name
latencylatency mode <mode>
Description: Configure latency
Syntax:
Configure Vlan Domain Membermode
modemode
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# latency mode <mode>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)804
L Commandslatency
layer2-switched flowlayer2-switched flow monitor <WORD>
Description: Configure Netflow on a Policy Group
Syntax:
Configure Netflow on a Policy Groupmonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# layer2-switched flow monitor <WORD>
layer2-switched flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# layer2-switched flow monitor <WORD>
layer2-switched flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 805
L Commandslayer2-switched flow
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# layer2-switched flow monitor <WORD>
layer2-switched flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# layer2-switched flow monitor <WORD>
layer2-switched flow monitor <arg>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# layer2-switched flow monitor <>
layer2-switched flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)806
L Commandslayer2-switched flow
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# layer2-switched flow monitor <WORD>
layer2-switched flow monitor <WORD>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# layer2-switched flow monitor <WORD>
layer2-switched flow monitor <arg>
Description: Configure Netflow on the Interface
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# layer2-switched flow monitor <>
layer2-switched flow monitor <WORD>
Description: Configure Netflow on the Interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 807
L Commandslayer2-switched flow
Syntax:
Configure Netflow on the Interfacemonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# layer2-switched flow monitor <WORD>
layer2-switched flow monitor <WORD>
Description: Configure Netflow on the VPC
Syntax:
Configure Netflow on the VPCmonitor
Netflow Monitor Policy Name (Max Size 64)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# layer2-switched flow monitor <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)808
L Commandslayer2-switched flow
ldap-server attributeldap-server attribute <WORD>
Description: An LDAP endpoint attribute to be used as the CiscoAVPair
Syntax:
LDAP endpoint attribute (Max Size 63)<WORD>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server attribute <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 809
L Commandsldap-server attribute
ldap-server basednldap-server basedn <WORD>
Description: The LDAP base DN for user lookup in the LDAP directory tree
Syntax:
user lookup in LDAP directory tree (Max Size 127)<WORD>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server basedn <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)810
L Commandsldap-server basedn
ldap-server filterldap-server filter <WORD>
Description: LDAP search filter for the LDAP endpoint
Syntax:
search filter for the LDAP endpoint (Max Size 63)<WORD>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server filter <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 811
L Commandsldap-server filter
ldap-server hostldap-server host <A.B.C.D|A:B::C:D|WORD>
Description: LDAP server DNS name or IP address
Syntax:
Provide a hostname or IPV4/IPV6 addressA.B.C.D|A:B::C:D|WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)812
L Commandsldap-server host
ldap-server retriesldap-server retries <NUMBER>
Description: Global LDAP server retransmit count
Syntax:
Global LDAP server retransmit count. Number range from=0 to=5<0-5>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server retries <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 813
L Commandsldap-server retries
ldap-server timeoutldap-server timeout <NUMBER>
Description: Global LDAP server timeout period in seconds
Syntax:
Global LDAP server timeout period in seconds. Number range from=1to=60
<1-60>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server timeout <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)814
L Commandsldap-server timeout
leaf-groupleaf-group <WORD>
Description: Configure Leaf Group
Syntax:
Leaf Group name (Max Size 64)WORD
Command Mode: leaf-profile : Configure Leaf Profile
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>
leaf-group <WORD>
Description: Configure Leaf Group
Syntax:
Leaf Group name (Max Size 64)WORD
Command Mode: leaf-profile : Configure Leaf Profile
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 815
L Commandsleaf-group
leaf-interface-groupleaf-interface-group <WORD>
Description: Configure Leaf Interface Group
Syntax:
Leaf Interface Group name (Max Size 64)WORD
Command Mode: leaf-interface-profile : Create Leaf Interface Profile
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>
leaf-interface-group <WORD>
Description: Configure Leaf Interface Group
Syntax:
Leaf Interface Group name (Max Size 64)WORD
Command Mode: leaf-interface-profile : Create Leaf Interface Profile
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)816
L Commandsleaf-interface-group
leaf-interface-profileleaf-interface-profile <WORD>
Description: Attach Leaf Interface Profile to the Leaf Profile
Syntax:
Leaf Interface Profile name (Max Size 64)WORD
Command Mode: leaf-profile : Configure Leaf Profile
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-interface-profile <WORD>
leaf-interface-profile <WORD>
Description: Create Leaf Interface Profile
Syntax:
Leaf Interface Profile name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>
leaf-interface-profile <WORD>
Description: Create Leaf Interface Profile
Syntax:
Leaf Interface Profile name (Max Size 64)WORD
Command Mode: fabric-internal : Fabric Policy Configuration for internal ports
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-interface-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 817
L Commandsleaf-interface-profile
leaf-interface-profile <WORD>
Description: Attach Leaf Interface Profile to the Leaf Profile
Syntax:
Leaf Interface Profile name (Max Size 64)WORD
Command Mode: leaf-profile : Configure Leaf Profile
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-profile <WORD>(config-leaf-profile)# leaf-interface-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)818
L Commandsleaf-interface-profile
leaf-policy-groupleaf-policy-group <WORD>
Description: Configure leaf policy group
Syntax:
Leaf policy name (Max Size 64)WORD
Command Mode: leaf-group : Configure Leaf Group
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# leaf-policy-group <WORD>
leaf-policy-group <WORD>
Description: Configure leaf policy group
Syntax:
Leaf policy name (Max Size 64)WORD
Command Mode: leaf-group : Configure Leaf Group
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# leaf-policy-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 819
L Commandsleaf-policy-group
leaf-profileleaf-profile <WORD>
Description: Configure Leaf Profile
Syntax:
Leaf Profile name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>
leaf-profile <WORD>
Description: Configure Leaf Profile
Syntax:
Leaf Profile name (Max Size 64)WORD
Command Mode: fabric-internal : Fabric Policy Configuration for internal ports
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)820
L Commandsleaf-profile
leafleaf <101-4000>
Description: Provide a Range of Nodes
Syntax:
Leaf Range or Leaf Name List<101-4000>
Command Mode: leaf-group : Configure Leaf Group
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# leaf <101-4000>
leaf <101-4000>
Description: Provide a Range of Nodes
Syntax:
Leaf Range or Leaf Name List<101-4000>
Command Mode: leaf-group : Configure Leaf Group
Command Path:
# configure [['terminal', 't']](config)# fabric-internal(config-fabric-internal)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# leaf <101-4000>
leaf <101-4000>
Description: Configure Leaf Node
Syntax:
Leaf Range or Leaf Name List<101-4000>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 821
L Commandsleaf
(config)# leaf <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)822
L Commandsleaf
legacylegacy forwarding vlan <NUMBER> vlan-domain <WORD>
Description: Set the bridge domain to behave as a L2 vlan in traditional ethernet environment
Syntax:
Forwarding keywordforwarding
Legacy Vlan Numbervlan
Legacy Vlan Number. Number range from=1 to=4094<1-4094>
Name of the vlan domain to usevlan-domain
Name of the vlan domain to use (Max Size 64)WORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# legacy forwarding vlan <NUMBER> vlan-domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 823
L Commandslegacy
linklink debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# link debounce time <NUMBER>
link debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# link debounce time <NUMBER>
link debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)824
L Commandslink
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: template spine-interface-policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template spine-interface-policy-group <WORD>(config-spine-if-pol-grp)# link debounce time <NUMBER>
link debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# link debounce time <NUMBER>
link debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 825
L Commandslink
(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# link debounce time <NUMBER>
link debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# link debounce time <NUMBER>
link debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# link debounce time <NUMBER>
link debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)826
L Commandslink
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# link debounce time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 827
L Commandslink
lldplldp receive|transmit|both|default
Description: Configure Interface LLDP parameters on DVS uplink ports
Syntax:
Enable LLDP receptionreceive
Enable LLDP transmissiontransmit
Enable LLDP in both directionsboth
Remove LLDP override policydefault
Command Mode: configure-dvs : Configure a VMWare Domain as DVS type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-dvs(config-vmware-dvs)# lldp receive|transmit|both|default
lldp receive|transmit|both|default
Description: Configure Interface LLDP parameters on AVS uplink ports
Syntax:
Enable LLDP receptionreceive
Enable LLDP transmissiontransmit
Enable LLDP in both directionsboth
Remove LLDP override policydefault
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# lldp receive|transmit|both|default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)828
L Commandslldp
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# lldp receive|transmit
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# lldp receive|transmit
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 829
L Commandslldp
(config-leaf-if)# lldp receive|transmit
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lldp receive|transmit
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# lldp receive|transmit
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: interface port-channel : Port Channel interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)830
L Commandslldp
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lldp receive|transmit
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lldp receive|transmit
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 831
L Commandslldp
lldp holdtimelldp holdtime <NUMBER>
Description: Specify the hold time to be sent in LLDP packets
Syntax:
Holdtime in sec. Number range from=10 to=255<10-255>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# lldp holdtime <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)832
L Commandslldp holdtime
lldp reinitlldp reinit <NUMBER>
Description: Specify the delay for LLDP initialization on an interface
Syntax:
Reinit Delay in sec. Number range from=1 to=10<1-10>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# lldp reinit <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 833
L Commandslldp reinit
lldp timerlldp timer <NUMBER>
Description: Specify the rate at which LLDP packets are sent
Syntax:
Rate of packets in sec. Number range from=5 to=254<5-254>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# lldp timer <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)834
L Commandslldp timer
load-balanceload-balance <WORD>
Description: Configure load balance hash fields
Syntax:
Hash FieldsWORD
Command Mode: lacp symmetric-hash : Configure symmetric hashing policy
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# lacp symmetric-hash(config-po-ch-sym-hash)# load-balance <WORD>
load-balance <WORD>
Description: Configure load balance hash fields
Syntax:
Hash FieldsWORD
Command Mode: lacp symmetric-hash : Configure symmetric hashing policy
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp symmetric-hash(config-po-ch-sym-hash)# load-balance <WORD>
load-balance <WORD>
Description: Configure load balance hash fields
Syntax:
Hash FieldsWORD
Command Mode: lacp symmetric-hash : Configure symmetric hashing policy
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 835
L Commandsload-balance
(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp symmetric-hash(config-po-ch-sym-hash)# load-balance <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)836
L Commandsload-balance
local-aslocal-as <NUMBER> no-prepend|replace-as|dual-as
Description: Local Autonomous System Configuration for a BGP Peer
Syntax:
The local autonomous system number. Number range from=1to=4294967295
<1-4294967295>
Do not prepend local-as to updates from ebgp peersno-prepend
Replace real AS with local AS in the EBGP updatesreplace-as
Accept either real AS or local AS from the ebgp peerdual-as
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# local-as <NUMBER> no-prepend|replace-as|dual-as
local-as <NUMBER> no-prepend|replace-as|dual-as
Description: Local Autonomous System Configuration for a BGP Peer
Syntax:
The local autonomous system number. Number range from=1to=4294967295
<1-4294967295>
Do not prepend local-as to updates from ebgp peersno-prepend
Replace real AS with local AS in the EBGP updatesreplace-as
Accept either real AS or local AS from the ebgp peerdual-as
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 837
L Commandslocal-as
(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# local-as <NUMBER> no-prepend|replace-as|dual-as
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)838
L Commandslocal-as
localitylocality <WORD>
Description: Set The city or town of the organization.
Syntax:
city or town (Max Size 64)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# locality <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 839
L Commandslocality
logfilelogfile [severity <severity>] [format <format>]
Description: Enable the logging to logfile
Syntax:
(Optional) The severity level for the logsseverity
(Optional) The format for the syslog messagesformat
Command Mode: logging : Logging server group configuration mode
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# logfile [severity <severity>] [format <format>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)840
L Commandslogfile
logginglogging server-group <WORD>
Description: Logging server group configuration mode
Syntax:
Logging Server-Group configurationserver-group
Logging server-group name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 841
L Commandslogging
logging auditlogging audit
Description: Enable audit and session logs to the policy
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging audit
logging audit
Description: Enable audit logs to the policy
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging audit
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)842
L Commandslogging audit
logging descriptionlogging description <WORD>
Description: Add description for syslog common
Syntax:
Description (Max Size 128) surrounded by single quotesWORD
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging description <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 843
L Commandslogging description
logging eventlogging event
Description: Enable event logs to the policy
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging event
logging event
Description: Enable event logs to the policy
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging event
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)844
L Commandslogging event
logging faultlogging fault
Description: Enable fault logs to the policy
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging fault
logging fault
Description: Enable fault logs to the policy
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging fault
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 845
L Commandslogging fault
logging server-grouplogging server-group <WORD>
Description: Logging server group configuration
Syntax:
Logging server-group name (Max Size 64)WORD
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging server-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)846
L Commandslogging server-group
logging sessionlogging session
Description: Enable session logs to the policy
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging session
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 847
L Commandslogging session
logging severitylogging severity info|notice|emergency|alert|critical|error|debug|warning
Description: Configure minimum severity level for logs generated
Syntax:
Infoinfo
Noticenotice
Emergencyemergency
Alertalert
Criticalcritical
Errorerror
Debugdebug
Warningwarning
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging severity info|notice|emergency|alert|critical|error|debug|warning
logging severity emergencies|debugging|critical|errors|warnings|information|alerts|notifications
Description: Configure minimum severity level for logs generated
Syntax:
Emergenciesemergencies
Debuggingdebugging
Criticalcritical
Errorserrors
Warningswarnings
Informationinformation
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)848
L Commandslogging severity
Alertsalerts
Notificationsnotifications
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging severityemergencies|debugging|critical|errors|warnings|information|alerts|notifications
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 849
L Commandslogging severity
logitlogit severity <severity> dest-grp <WORD> server <Remote Dest Name> <Syslog message>
Description: Syslog send message command
Syntax:
The severity level for the logsseverity
severityseverity
Remote destination groupdest-grp
Logging server-group name (Max Size 64)WORD
Remote destination nameserver
The hostname or ipaddressRemote Dest Name
Message sent to syslog serverSyslog message
Command Mode: exec : Exec Mode
Command Path:
# logit severity <severity> dest-grp <WORD> server <Remote Dest Name> <Syslog message>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)850
L Commandslogit
logit severity dest-grp server nodelogit severity <severity> dest-grp <WORD> server <Remote Dest Name> <Syslog message> node <Sourcenode>
Description: Source node
Syntax:
The severity level for the logsseverity
severityseverity
Remote destination groupdest-grp
Logging server-group name (Max Size 64)WORD
Remote destination nameserver
The hostname or ipaddressRemote Dest Name
Message sent to syslog serverSyslog message
leaf or spine node. Number range from=0 to=9223372036854775807Source node
Command Mode: exec : Exec Mode
Command Path:
# logit severity <severity> dest-grp <WORD> server <Remote Dest Name> <Syslog message> node<Source node>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 851
L Commandslogit severity dest-grp server node
lsp-fast-floodlsp-fast-flood
Description: Enables the ISIS LSP fast flood
Command Mode: isis : Intermediate System to Intermediate System (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# isis fabric(config-pod-isis)# lsp-fast-flood
lsp-fast-flood
Description: Enables the ISIS LSP fast flood
Command Mode: template isis-fabric : InterSystem-InterSystem Protocol (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# template isis-fabric <WORD>(config-template-isis-fabric)# lsp-fast-flood
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)852
L Commandslsp-fast-flood
lsp-gen-intervallsp-gen-interval level-1 <NUMBER> <50-120000> <50-120000>
Description: Set the ISIS LSP generation maximal wait interval
Syntax:
Level 1level-1
LSP generation maximum wait interval. Number range from=50to=120000
<50-120000>
Initial and secondary wait intervals (both values are required)<50-120000> <50-120000>
Command Mode: isis : Intermediate System to Intermediate System (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# isis fabric(config-pod-isis)# lsp-gen-interval level-1 <NUMBER> <50-120000> <50-120000>
lsp-gen-interval level-1 <NUMBER> <50-120000> <50-120000>
Description: Set the ISIS LSP generation maximal wait interval
Syntax:
Level 1level-1
LSP generation maximum wait interval. Number range from=50to=120000
<50-120000>
Initial and secondary wait intervals (both values are required)<50-120000> <50-120000>
Command Mode: template isis-fabric : InterSystem-InterSystem Protocol (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# template isis-fabric <WORD>(config-template-isis-fabric)# lsp-gen-interval level-1 <NUMBER> <50-120000> <50-120000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 853
L Commandslsp-gen-interval
lsp-mtulsp-mtu <NUMBER>
Description: Set the configuration of link-state packet (LSP) maximum transmission units (MTU) value
Syntax:
The configuration of link-state packet (LSP) maximum transmissionunits (MTU).. Number range from=256 to=4352
<256-4352>
Command Mode: isis : Intermediate System to Intermediate System (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# isis fabric(config-pod-isis)# lsp-mtu <NUMBER>
lsp-mtu <NUMBER>
Description: Set the configuration of link-state packet (LSP) maximum transmission units (MTU) value
Syntax:
The configuration of link-state packet (LSP) maximum transmissionunits (MTU).. Number range from=256 to=4352
<256-4352>
Command Mode: template isis-fabric : InterSystem-InterSystem Protocol (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# template isis-fabric <WORD>(config-template-isis-fabric)# lsp-mtu <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)854
L Commandslsp-mtu
M Commands
• mac-address, page 858
• mac-changes, page 861
• mac-learning, page 862
• managed-config-check, page 863
• managed-config-flag, page 864
• match-precedence, page 865
• match, page 866
• match arp, page 868
• match bridge-domain, page 869
• match dscp, page 870
• match icmp, page 871
• match ip, page 872
• match ip multicast group, page 873
• match ip multicast group rp, page 874
• match ip multicast group rp source, page 875
• match ip multicast group source, page 876
• match ip multicast group source rp, page 877
• match ip multicast rp, page 878
• match ip multicast rp group, page 879
• match ip multicast rp group source, page 880
• match ip multicast rp source, page 881
• match ip multicast rp source group, page 882
• match ip multicast source, page 883
• match ip multicast source group, page 884
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 855
• match ip multicast source group rp, page 885
• match ip multicast source rp, page 886
• match ip multicast source rp group, page 887
• match ipv6, page 888
• match prefix-list, page 889
• match raw, page 890
• match route group, page 891
• match tcp, page 892
• match udp, page 893
• max-lsa, page 894
• max-validity-period, page 896
• max concurrent, page 897
• max running, page 898
• maxas-limit, page 899
• maximum-hop-limit, page 900
• maximum-paths, page 901
• maximum-prefix, page 904
• maximum-router-preference, page 906
• mcp, page 907
• mcp action, page 910
• mcp control pdu-per-vlan, page 911
• mcp description, page 912
• mcp enable, page 913
• mcp factor, page 914
• mcp init-delay, page 915
• mcp transmit-frequency, page 916
• member, page 917
• message-level, page 918
• message-size, page 919
• metric, page 920
• mgmt-connectivity-pref, page 922
• mgmt-epg, page 923
• microsoft-domain, page 924
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)856
M Commands
• microsoft, page 926
• min-rx, page 927
• min-tx, page 929
• min, page 931
• minimum-hop-limit, page 932
• mode, page 933
• modulus, page 934
• monitor, page 935
• monitor access, page 936
• monitor fabric, page 937
• monitor tenant, page 938
• monitor virtual, page 939
• mtu-ignore, page 940
• mtu, page 941
• multi-destination, page 945
• multi-site-mac-address, page 946
• multicast-address, page 947
• multiplier, page 948
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 857
M Commands
mac-addressmac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Add a custom MAC address to the bridgedomain
Syntax:
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# mac-addressE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description:Manually set interface MAC address
Syntax:
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)858
M Commandsmac-address
mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure mac Address
Syntax:
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
mac-address <WORD>
Description: Virtual MAC address
Syntax:
MAC address(FORMAT:xxxx.xxxx.xxxx)WORD
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# mac-address <WORD>
mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description:Manually set interface MAC address
Syntax:
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 859
M Commandsmac-address
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure mac Address
Syntax:
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
mac-address <WORD>
Description: Virtual MAC address
Syntax:
MAC address(FORMAT:xxxx.xxxx.xxxx)WORD
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# mac-address <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)860
M Commandsmac-address
mac-changesmac-changes accept
Description: Enable/disable MAC changes on trunk
Syntax:
enableaccept
Command Mode: trunk-portgroup : Configure a trunk port group in the VMWare domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# trunk-portgroup <>(config-vmware-trunk)# mac-changes accept
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 861
M Commandsmac-changes
mac-learningmac-learning <arg>
Description: enable/disable mac-learning on the qinq-tunnel
Syntax:
arg
Command Mode: dot1q-tunnel : Tunnel configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# dot1q-tunnel <WORD>(config-tenant-tunnel)#mac-learning <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)862
M Commandsmac-learning
managed-config-checkmanaged-config-check
Description: Enable managed address configuration check in router advertisement guard policy
Command Mode: router-advertisement-guard : Configuration for router advertisement guard policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>(config-tenant-fhs-secpol)# router-advertisement-guard(config-tenant-fhs-raguard)# managed-config-check
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 863
M Commandsmanaged-config-check
managed-config-flagmanaged-config-flag
Description: Set managed address configuration flag in router advertisement guard policy
Command Mode: router-advertisement-guard : Configuration for router advertisement guard policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>(config-tenant-fhs-secpol)# router-advertisement-guard(config-tenant-fhs-raguard)# managed-config-flag
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)864
M Commandsmanaged-config-flag
match-precedencematch-precedence <integer-value>
Description: Configure User Precedence
Syntax:
Configure User Precedenceinteger-value
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# match-precedence <integer-value>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 865
M Commandsmatch-precedence
matchmatch dscp|dot1p <WORD> <WORD> [set-class <WORD>] [set-dscp <WORD>] [set-cos <WORD>]
Description: Add a rule to match DSCP or DOT1P, queue the traffic and optionally mutate it
Syntax:
Match entry for DSCPdscp
Match entry for DOT1Pdot1p
From of DSCP or DOT1P rangeWORD
To of DSCP or DOT1P rangeWORD
(Optional) Set the QOS class for the trafficWORD
(Optional) DSCP rewriteWORD
(Optional) Dot1P rewriteWORD
Command Mode: policy-map type qos : QOS policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type qos <WORD>(config-tenant-pmap-qos)# match dscp|dot1p <WORD> <WORD> [set-class <WORD>] [set-dscp <WORD>][set-cos <WORD>]
match <arg>
Description: Configure match
Syntax:
arg
Command Mode: flow record : Configure Netflow Record
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow record <WORD>(config-tn-flow-record)# match <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)866
M Commandsmatch
match <arg>
Description: Configure match
Syntax:
arg
Command Mode: flow record : Configure Netflow Record
Command Path:
# configure [['terminal', 't']](config)# flow record <WORD>(config-flow-record)# match <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 867
M Commandsmatch
match arpmatch arp
Description:Match the ARP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)868
M Commandsmatch arp
match bridge-domainmatch bridge-domain <arg> [tenant <tenant>]
Description:Match subnets of a bridge-domain
Syntax:
arg
(Optional) Tenant nametenant
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>]
match bridge-domain <arg> [tenant <tenant>]
Description:Match subnets of a bridge-domain
Syntax:
arg
(Optional) Tenant nametenant
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 869
M Commandsmatch bridge-domain
match dscpmatch dscp <0-64>
Description:Match DSCP traffic
Syntax:
DSCP Value<0-64>
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match dscp <0-64>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)870
M Commandsmatch dscp
match icmpmatch icmp
Description:Match the ICMP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match icmp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 871
M Commandsmatch icmp
match ipmatch ip
Description:Match the IP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match ip
match ip <A.B.C.D/LEN> [shared]
Description: Add a subnet that identify hosts being part of the epg
Syntax:
IP prefix and network mask lengthA.B.C.D/LEN
(Optional) Add the shared scope to the existing scope for the subnetshared
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# match ip <A.B.C.D/LEN> [shared]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)872
M Commandsmatch ip
match ip multicast groupmatch ip multicast group <A.B.C.D/LEN>
Description:Multicast Group prefix
Syntax:
IPv4 group prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast group <A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 873
M Commandsmatch ip multicast group
match ip multicast group rpmatch ip multicast group <A.B.C.D/LEN> rp <A.B.C.D/LEN>
Description: Rendezvous point prefix
Syntax:
IPv4 group prefix and network mask lengthA.B.C.D/LEN
IPv4 Rendezvous point prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast group <A.B.C.D/LEN> rp <A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)874
M Commandsmatch ip multicast group rp
match ip multicast group rp sourcematch ip multicast group <A.B.C.D/LEN> rp <A.B.C.D/LEN> source <A.B.C.D/LEN>
Description: source prefix
Syntax:
IPv4 group prefix and network mask lengthA.B.C.D/LEN
IPv4 Rendezvous point prefix and network mask lengthA.B.C.D/LEN
IPv4 source prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast group <A.B.C.D/LEN> rp <A.B.C.D/LEN> source<A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 875
M Commandsmatch ip multicast group rp source
match ip multicast group sourcematch ip multicast group <A.B.C.D/LEN> source <A.B.C.D/LEN>
Description: source prefix
Syntax:
IPv4 group prefix and network mask lengthA.B.C.D/LEN
IPv4 source prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast group <A.B.C.D/LEN> source <A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)876
M Commandsmatch ip multicast group source
match ip multicast group source rpmatch ip multicast group <A.B.C.D/LEN> source <A.B.C.D/LEN> rp <A.B.C.D/LEN>
Description: Rendezvous point prefix
Syntax:
IPv4 group prefix and network mask lengthA.B.C.D/LEN
IPv4 source prefix and network mask lengthA.B.C.D/LEN
IPv4 Rendezvous point prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast group <A.B.C.D/LEN> source <A.B.C.D/LEN> rp<A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 877
M Commandsmatch ip multicast group source rp
match ip multicast rpmatch ip multicast rp <A.B.C.D/LEN>
Description: Rendezvous point prefix
Syntax:
IPv4 Rendezvous point prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast rp <A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)878
M Commandsmatch ip multicast rp
match ip multicast rp groupmatch ip multicast rp <A.B.C.D/LEN> group <A.B.C.D/LEN>
Description:Multicast Group prefix
Syntax:
IPv4 Rendezvous point prefix and network mask lengthA.B.C.D/LEN
IPv4 group prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast rp <A.B.C.D/LEN> group <A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 879
M Commandsmatch ip multicast rp group
match ip multicast rp group sourcematch ip multicast rp <A.B.C.D/LEN> group <A.B.C.D/LEN> source <A.B.C.D/LEN>
Description: source prefix
Syntax:
IPv4 Rendezvous point prefix and network mask lengthA.B.C.D/LEN
IPv4 group prefix and network mask lengthA.B.C.D/LEN
IPv4 source prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast rp <A.B.C.D/LEN> group <A.B.C.D/LEN> source<A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)880
M Commandsmatch ip multicast rp group source
match ip multicast rp sourcematch ip multicast rp <A.B.C.D/LEN> source <A.B.C.D/LEN>
Description:Multicast Group prefix
Syntax:
IPv4 Rendezvous point prefix and network mask lengthA.B.C.D/LEN
IPv4 source prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast rp <A.B.C.D/LEN> source <A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 881
M Commandsmatch ip multicast rp source
match ip multicast rp source groupmatch ip multicast rp <A.B.C.D/LEN> source <A.B.C.D/LEN> group <A.B.C.D/LEN>
Description:Multicast Group prefix
Syntax:
IPv4 Rendezvous point prefix and network mask lengthA.B.C.D/LEN
IPv4 source prefix and network mask lengthA.B.C.D/LEN
IPv4 group prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast rp <A.B.C.D/LEN> source <A.B.C.D/LEN> group<A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)882
M Commandsmatch ip multicast rp source group
match ip multicast sourcematch ip multicast source <A.B.C.D/LEN>
Description:Multicast Group prefix
Syntax:
IPv4 source prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast source <A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 883
M Commandsmatch ip multicast source
match ip multicast source groupmatch ip multicast source <A.B.C.D/LEN> group <A.B.C.D/LEN>
Description:Multicast Group prefix
Syntax:
IPv4 source prefix and network mask lengthA.B.C.D/LEN
IPv4 group prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast source <A.B.C.D/LEN> group <A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)884
M Commandsmatch ip multicast source group
match ip multicast source group rpmatch ip multicast source <A.B.C.D/LEN> group <A.B.C.D/LEN> rp <A.B.C.D/LEN>
Description: Rendezvous point prefix
Syntax:
IPv4 source prefix and network mask lengthA.B.C.D/LEN
IPv4 group prefix and network mask lengthA.B.C.D/LEN
IPv4 Rendezvous point prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast source <A.B.C.D/LEN> group <A.B.C.D/LEN> rp<A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 885
M Commandsmatch ip multicast source group rp
match ip multicast source rpmatch ip multicast source <A.B.C.D/LEN> rp <A.B.C.D/LEN>
Description: Rendezvous point prefix
Syntax:
IPv4 source prefix and network mask lengthA.B.C.D/LEN
IPv4 Rendezvous point prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast source <A.B.C.D/LEN> rp <A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)886
M Commandsmatch ip multicast source rp
match ip multicast source rp groupmatch ip multicast source <A.B.C.D/LEN> rp <A.B.C.D/LEN> group <A.B.C.D/LEN>
Description:Multicast Group prefix
Syntax:
IPv4 source prefix and network mask lengthA.B.C.D/LEN
IPv4 Rendezvous point prefix and network mask lengthA.B.C.D/LEN
IPv4 group prefix and network mask lengthA.B.C.D/LEN
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>(config-tenant-rtmap)# match ip multicast source <A.B.C.D/LEN> rp <A.B.C.D/LEN> group<A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 887
M Commandsmatch ip multicast source rp group
match ipv6match ipv6 X:X:X:X::X/<0-128>
Description: Add a subnet that identify hosts being part of the epg
Syntax:
IPv6 prefix and network mask lengthX:X:X:X::X/<0-128>
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# match ipv6 X:X:X:X::X/<0-128>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)888
M Commandsmatch ipv6
match prefix-listmatch prefix-list <WORD> [deny]
Description:Match entries of a prefix-list
Syntax:
Name of prefix-list (Max Size 63)WORD
(Optional) Reject routes on matchdeny
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny]
match prefix-list <WORD> [deny]
Description:Match entries of a prefix-list
Syntax:
Name of prefix-list (Max Size 63)WORD
(Optional) Reject routes on matchdeny
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 889
M Commandsmatch prefix-list
match rawmatch raw <WORD> [tcpRules <tcpRules>] [arpOpc <arpOpc>] [applyToFrag <applyToFrag>] [dToPort<NUMBER>] [prot <NUMBER>] [icmpv4T <icmpv4T>] [stateful <stateful>] [icmpv6T <icmpv6T>] [sToPort<NUMBER>] [etherT <etherT>] [sFromPort <NUMBER>] [dFromPort <NUMBER>] [matchDscp <0-64>]
Description: Specify a raw vzEntry
Syntax:
Entry Name (Max Size 64)WORD
(Optional) TCP Flags as comma separated values like val1,val2,..valNtcpRules
(Optional) ARP OpcodesarpOpc
(Optional) Apply to FragmentapplyToFrag
(Optional) L4 Destination Port. Number range from=0 to=65535<0-65535>
(Optional) IP Protocol. Number range from=0 to=255<0-255>
(Optional) ICMP Typeicmpv4T
(Optional) Stateful flagstateful
(Optional) ICMPv6 Typeicmpv6T
(Optional) L4 Source Port. Number range from=0 to=65535<0-65535>
(Optional) Ethernet TypeetherT
(Optional) L4 Source Port. Number range from=0 to=65535<0-65535>
(Optional) L4 Destination Port. Number range from=0 to=65535<0-65535>
(Optional) DSCP Value<0-64>
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match raw <WORD> [tcpRules <tcpRules>] [arpOpc <arpOpc>] [applyToFrag<applyToFrag>] [dToPort <NUMBER>] [prot <NUMBER>] [icmpv4T <icmpv4T>] [stateful <stateful>][icmpv6T <icmpv6T>] [sToPort <NUMBER>] [etherT <etherT>] [sFromPort <NUMBER>] [dFromPort<NUMBER>] [matchDscp <0-64>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)890
M Commandsmatch raw
match route groupmatch route group <arg> [order <order>] [deny]
Description: Route group
Syntax:
arg
(Optional) Relative order for the entry. Number range from=0 to=9order
(Optional) Reject routes on matchdeny
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny]
match route group <arg> [order <order>] [deny]
Description: Route group
Syntax:
arg
(Optional) Relative order for the entry. Number range from=0 to=9order
(Optional) Reject routes on matchdeny
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 891
M Commandsmatch route group
match tcpmatch tcp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>] contained in <0-65535>]
Description:Match TCP traffic
Syntax:
(Optional) TCP Source port Range<from>-[<to>] contained in<0-65535>
(Optional) TCP Destination port Range<from>-[<to>] contained in<0-65535>
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match tcp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>]contained in <0-65535>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)892
M Commandsmatch tcp
match udpmatch udp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>] contained in <0-65535>]
Description:Match UDP traffic
Syntax:
(Optional) UDP Source port Range<from>-[<to>] contained in<0-65535>
(Optional) UDP Destination port Range<from>-[<to>] contained in<0-65535>
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match udp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>]contained in <0-65535>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 893
M Commandsmatch udp
max-lsamax-lsa <NUMBER> <NUMBER> reject|restart|log
Description: Feature to limit the number of non-self-originated LSAs
Syntax:
Set maximum number of non self-generated LSAs. Number rangefrom=1 to=4294967295
<1-4294967295>
Threshold value (%) at which to generate a warning message. Numberrange from=1 to=100
<1-100>
Reject LSAs beyond the limitreject
Restart the neighborrestart
log a warninglog
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# max-lsa <NUMBER> <NUMBER> reject|restart|log
max-lsa <NUMBER> <NUMBER> reject|restart|log
Description: Feature to limit the number of non-self-originated LSAs
Syntax:
Set maximum number of non self-generated LSAs. Number rangefrom=1 to=4294967295
<1-4294967295>
Threshold value (%) at which to generate a warning message. Numberrange from=1 to=100
<1-100>
Reject LSAs beyond the limitreject
Restart the neighborrestart
log a warninglog
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)894
M Commandsmax-lsa
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# max-lsa <NUMBER> <NUMBER> reject|restart|log
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 895
M Commandsmax-lsa
max-validity-periodmax-validity-period <NUMBER>
Description: Set The maximum validity period for a webtoken
Syntax:
Set Themaximumvalidity period for a webtoken. Number range from=4to=24
<4-24>
Command Mode: crypto webtoken : The cryptographic data used for generating and verifying web tokens.
Command Path:
# configure [['terminal', 't']](config)# crypto webtoken(config-webtoken)# max-validity-period <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)896
M Commandsmax-validity-period
max concurrentmax concurrent nodes <NUMBER>
Description: Set the window maximum concurrent node limit
Syntax:
Maximum number of tasks that can be processed concurrently.nodes
Enter maximum number of concurrent nodes. 0 for unlimited. Numberrange from=0 to=65535
<0-65535>
Command Mode: absolute : Absolute window configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# absolute window <WORD>(config-scheduler-absolute)# max concurrent nodes <NUMBER>
max concurrent nodes <NUMBER>
Description: Set the window maximum concurrent node limit
Syntax:
Maximum number of tasks that can be processed concurrently.nodes
Enter maximum number of concurrent nodes. 0 for unlimited. Numberrange from=0 to=65535
<0-65535>
Command Mode: recurring : Recurring window configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>(config-scheduler-recurring)# max concurrent nodes <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 897
M Commandsmax concurrent
max runningmax running time <TIME>
Description: Set the window maximum running time
Syntax:
Maximum running timetime
Enter the maximum running time in dd:hh:mm:ss. 0 for unlimitedTIME
Command Mode: absolute : Absolute window configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# absolute window <WORD>(config-scheduler-absolute)# max running time <TIME>
max running time <TIME>
Description: Set the window maximum running time
Syntax:
Maximum running time in millisecondstime
Enter the maximum running time in dd:hh:mm:ss. 0 for unlimitedTIME
Command Mode: recurring : Recurring window configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>(config-scheduler-recurring)# max running time <TIME>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)898
M Commandsmax running
maxas-limitmaxas-limit <NUMBER>
Description: Configure BGP Maximum AS limit
Syntax:
BGP Maximum AS limit. Number range from=0 to=2000<0-2000>
Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# maxas-limit <NUMBER>
maxas-limit <NUMBER>
Description: Configure BGP Maximum AS limit
Syntax:
BGP Maximum AS limit. Number range from=0 to=2000<0-2000>
Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# maxas-limit <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 899
M Commandsmaxas-limit
maximum-hop-limitmaximum-hop-limit <NUMBER>
Description: Config maximum hop limit in router advertisement guard policy
Syntax:
Specify hop limit. Number range from=1 to=255<hop-limit>
Command Mode: router-advertisement-guard : Configuration for router advertisement guard policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>(config-tenant-fhs-secpol)# router-advertisement-guard(config-tenant-fhs-raguard)# maximum-hop-limit <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)900
M Commandsmaximum-hop-limit
maximum-pathsmaximum-paths <NUMBER>
Description: Set the maximum ECMP for the OSPF protocol
Syntax:
Maximum paths. Number range from=1 to=64<1-64>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# maximum-paths <NUMBER>
maximum-paths <arg> <arg>
Description: Configure multipath for BGP paths
Syntax:
arg
arg
Command Mode: template bgp address-family : Configure Router BGP Address Family Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp address-family <WORD> tenant <WORD>(config-bgp-af)# maximum-paths <> <>
maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
Maximum Path Limit. Number range from=1 to=16<1-16>
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 901
M Commandsmaximum-paths
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# maximum-paths <NUMBER>
maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
Maximum Path Limit. Number range from=1 to=16<1-16>
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# maximum-paths <NUMBER>
maximum-paths <NUMBER>
Description: Set the maximum ECMP for the OSPF protocol
Syntax:
Maximum paths. Number range from=1 to=64<1-64>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# maximum-paths <NUMBER>
maximum-paths <arg> <arg>
Description: Configure multipath for BGP paths
Syntax:
arg
arg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)902
M Commandsmaximum-paths
Command Mode: template bgp address-family : Configure Router BGP Address Family Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bgp address-family <WORD> tenant <WORD>(config-bgp-af)# maximum-paths <> <>
maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
Maximum Path Limit. Number range from=1 to=16<1-16>
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# maximum-paths <NUMBER>
maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
Maximum Path Limit. Number range from=1 to=16<1-16>
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# maximum-paths <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 903
M Commandsmaximum-paths
maximum-prefixmaximum-prefix <NUMBER> [action <action>] [threshold <NUMBER>] [restart-time <NUMBER>]
Description:Maximum number of prefixes from this neighbor
Syntax:
Max. prefix limit. Number range from=1 to=300000<1-300000>
(Optional) Action to be performed when the maximum prefix limit isreached
<action>
(Optional) The threshold % of the maximum number of prefixes beforea warning is issued. Number range from=1 to=100
<1-100>
(Optional) The period of time in minutes before restarting the peer whenthe prefix limit is reached. Number range from=1 to=65535
<1-65535>
Command Mode: address-family : Configure an address-family for peer
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6|l2vpn unicast|evpn(config-leaf-bgp-vrf-neighbor-af)# maximum-prefix <NUMBER> [action <action>] [threshold<NUMBER>] [restart-time <NUMBER>]
maximum-prefix <NUMBER> [action <action>] [threshold <NUMBER>] [restart-time <NUMBER>]
Description:Maximum number of prefixes from this neighbor
Syntax:
Max. prefix limit. Number range from=1 to=300000<1-300000>
(Optional) Action to be performed when the maximum prefix limit isreached
<action>
(Optional) The threshold % of the maximum number of prefixes beforea warning is issued. Number range from=1 to=100
<1-100>
(Optional) The period of time in minutes before restarting the peer whenthe prefix limit is reached. Number range from=1 to=65535
<1-65535>
Command Mode: address-family : Configure an address-family for peer
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)904
M Commandsmaximum-prefix
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6|l2vpn unicast|evpn(config-leaf-bgp-vrf-neighbor-af)# maximum-prefix <NUMBER> [action <action>] [threshold<NUMBER>] [restart-time <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 905
M Commandsmaximum-prefix
maximum-router-preferencemaximum-router-preference high|low|medium
Description: Config maximum router preference in router advertisement guard policy
Syntax:
Configure router preference as highhigh
Configure router preference as lowlow
Configure router preference as mediummedium
Command Mode: router-advertisement-guard : Configuration for router advertisement guard policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>(config-tenant-fhs-secpol)# router-advertisement-guard(config-tenant-fhs-raguard)# maximum-router-preference high|low|medium
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)906
M Commandsmaximum-router-preference
mcpmcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# mcp enable
mcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# mcp enable
mcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# mcp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 907
M Commandsmcp
mcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# mcp enable
mcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# mcp enable
mcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# mcp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)908
M Commandsmcp
mcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# mcp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 909
M Commandsmcp
mcp actionmcp action port-disable
Description: Configure MCP Loop Protection Action
Syntax:
Disable the port when MCP detects loopport-disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp action port-disable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)910
M Commandsmcp action
mcp control pdu-per-vlanmcp control pdu-per-vlan
Description: Configure MCP State Control To Pdu-per-vlan
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp control pdu-per-vlan
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 911
M Commandsmcp control pdu-per-vlan
mcp descriptionmcp description <description>
Description: Update description for MCP policy
Syntax:
<description>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp description <description>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)912
M Commandsmcp description
mcp enablemcp enable key <WORD>
Description: Enable/Disable MCP Protocol
Syntax:
Configure MCP keykey
MCP keyWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp enable key <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 913
M Commandsmcp enable
mcp factormcp factor <NUMBER>
Description: Configure MCP Loop Detection Factor
Syntax:
MCP Loop Detection Multipication Factor. Number range from=1to=255
<1-255>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp factor <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)914
M Commandsmcp factor
mcp init-delaymcp init-delay <NUMBER>
Description: Configure MCP Loop Detection Init Delay Time
Syntax:
MCP Loop Detection Init Delay Time. Number range from=0 to=1800<0-1800>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp init-delay <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 915
M Commandsmcp init-delay
mcp transmit-frequencymcp transmit-frequency <NUMBER>
Description: Configure MCP Advertisement Transmit Frequency
Syntax:
MCP Advertisement Tx Frequency. Number range from=2 to=300<2-300>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp transmit-frequency <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)916
M Commandsmcp transmit-frequency
membermember device <WORD> device-interface <WORD>
Description: Configure Cluster Interface Member
Syntax:
Cluster Devicedevice
Cluster Device name (Max Size 64)WORD
Cluster Device Interfacedevice-interface
Cluster Device Interface (Max Size 256)WORD
Command Mode: cluster-interface : Configure L4-L7 Cluster Interface
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>] [context <context>] [trunking <enable|disable>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 917
M Commandsmember
message-levelmessage-level info|notice|emergency|alert|critical|error|debug|warning
Description: Configure the urgency of the message
Syntax:
Infoinfo
Noticenotice
Emergencyemergency
Alertalert
Criticalcritical
Errorerror
Debugdebug
Warningwarning
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# message-levelinfo|notice|emergency|alert|critical|error|debug|warning
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)918
M Commandsmessage-level
message-sizemessage-size <NUMBER>
Description: Configure the size of the message
Syntax:
The size of the messages. Number range from=0 to=5000000<size>
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# message-size <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 919
M Commandsmessage-size
metricmetric version 64bit
Description: Set EIGRP Metric Style
Syntax:
Metric Styleversion
wide metric64bit
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# metric version 64bit
metric version 64bit
Description: Set EIGRP Metric Style
Syntax:
Metric Styleversion
wide metric64bit
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# metric version 64bit
metric version 64bit
Description: Set EIGRP Metric Style
Syntax:
Metric Styleversion
wide metric64bit
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)920
M Commandsmetric
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# metric version 64bit
metric version 64bit
Description: Set EIGRP Metric Style
Syntax:
Metric Styleversion
wide metric64bit
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# metric version 64bit
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 921
M Commandsmetric
mgmt-connectivity-prefmgmt-connectivity-pref inband|ooband
Description: Set Mgmt Connectivity Preference
Syntax:
Set to inbandinband
Set to outbandooband
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mgmt-connectivity-pref inband|ooband
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)922
M Commandsmgmt-connectivity-pref
mgmt-epgmgmt-epg in-band|out-of-band <WORD>
Description: Select remote path management EPG
Syntax:
In-Band EPGin-band
Out-of-Band EPGout-of-band
Management EPG nameWORD
Command Mode: remote : Remote path configuration mode
Command Path:
# configure [['terminal', 't']](config)# remote path <WORD>(config-remote)# mgmt-epg in-band|out-of-band <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 923
M Commandsmgmt-epg
microsoft-domainmicrosoft-domain <WORD> [delimiter <WORD>]
Description: Create a VMMMicrosoft Domain
Syntax:
VMMMicrosoft Domain nameWORD
(Optional) Custom DelimiterWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# microsoft-domain <WORD> [delimiter <WORD>]
microsoft-domain member <WORD> [encap <WORD>] [primary-encap <WORD>] [deploy <WORD>] [push<WORD>] [delimiter <WORD>]
Description: Associate EPG to a Microsoft Domain
Syntax:
Bind the EPG to a Microsoft domainmember
Microsoft Domain NameWORD
(Optional) Enforce encap value. Secondary encapwhen EPG is isolated(For example vlan-10 or auto)
WORD
(Optional) Primary encap when EPG is isolated (For example vlan-11or auto)
WORD
(Optional) Deployment modeWORD
(Optional) Push modeWORD
(Optional) Custom DelimiterWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)924
M Commandsmicrosoft-domain
(config-tenant-app-epg)# microsoft-domain member <WORD> [encap <WORD>] [primary-encap <WORD>][deploy <WORD>] [push <WORD>] [delimiter <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 925
M Commandsmicrosoft-domain
microsoftmicrosoft static-ip-pool <name> gateway <gwAddress>
Description: Configure static IP pool
Syntax:
Configure the static IP poolstatic-ip-pool
enter the name of the static IP poolname
Configure gateway address on interfacegateway
gwAddressgwAddress
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)926
M Commandsmicrosoft
min-rxmin-rx <NUMBER>
Description: Configure BFD MIN-RX value in milliseconds
Syntax:
BFD interval. Number range from=50 to=999<interval>
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# min-rx <NUMBER>
min-rx <NUMBER>
Description: Configure required Minimum Rx Interval in milliseconds
Syntax:
Minimum Rx Interval. Number range from=50 to=999<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# min-rx <NUMBER>
min-rx <NUMBER>
Description: Configure required Minimum Rx Interval in milliseconds
Syntax:
Minimum Rx Interval. Number range from=50 to=999<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bfd <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 927
M Commandsmin-rx
(config-template-bfd-pol)# min-rx <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)928
M Commandsmin-rx
min-txmin-tx <NUMBER>
Description: Configure BFD MIN-TX value in milliseconds
Syntax:
BFD interval. Number range from=50 to=999<interval>
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# min-tx <NUMBER>
min-tx <NUMBER>
Description: Configure required Minimum Tx Interval in milliseconds
Syntax:
Minimum Tx Interval. Number range from=50 to=999<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# min-tx <NUMBER>
min-tx <NUMBER>
Description: Configure required Minimum Tx Interval in milliseconds
Syntax:
Minimum Tx Interval. Number range from=50 to=999<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bfd <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 929
M Commandsmin-tx
(config-template-bfd-pol)# min-tx <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)930
M Commandsmin-tx
minmin buffer <0-3>
Description: Set the minimum number of buffer of MTU size to be reserved
Syntax:
Number of minim buffers to reservebuffer
Number of minim buffers to reserve<0-3>
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# min buffer <0-3>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 931
M Commandsmin
minimum-hop-limitminimum-hop-limit <NUMBER>
Description: Config minimum hop limit in router advertisement guard policy
Syntax:
Specify hop limit. Number range from=1 to=255<hop-limit>
Command Mode: router-advertisement-guard : Configuration for router advertisement guard policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>(config-tenant-fhs-secpol)# router-advertisement-guard(config-tenant-fhs-raguard)# minimum-hop-limit <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)932
M Commandsminimum-hop-limit
modemode atomic|best-effort
Description: Snapshot import mode atomic|best-effort
Syntax:
Atomic modeatomic
Best Effort modebest-effort
Command Mode: snapshot import : Configuration import setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# mode atomic|best-effort
mode None|Dom
Description: Configure Node Control Mode
Syntax:
Disable Dom (Digital Optical Monitoring)None
Enable Dom (Digital Optical MonitoringDom
Command Mode: node-control : Create a Node Control Policy
Command Path:
# configure [['terminal', 't']](config)# node-control policy <WORD>(config-node)# mode None|Dom
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 933
M Commandsmode
modulusmodulus <modulus>
Description: Set the length of the encryption keys
Syntax:
<modulus><modulus>
Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# modulus <modulus>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)934
M Commandsmodulus
monitormonitor virtual session <WORD>
Description: Configure a monitor session
Syntax:
virtualvirtual
sessionsession
session name (Max Size 64)WORD
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# monitor virtual session <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 935
M Commandsmonitor
monitor accessmonitor access session <session_name>
Description: Configue monitor session for access interfaces
Syntax:
sessionsession
session name (Max Size 59)session_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)936
M Commandsmonitor access
monitor fabricmonitor fabric session <session_name>
Description: Configue monitor session for fabric interfaces
Syntax:
sessionsession
session name (Max Size 59)session_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 937
M Commandsmonitor fabric
monitor tenantmonitor tenant <tenant_name> session <WORD>
Description: Configue monitor session for tenant EPGs
Syntax:
tenant name (Max Size 63)tenant_name
sessionsession
session name (Max Size 59)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)938
M Commandsmonitor tenant
monitor virtualmonitor virtual session <WORD>
Description: Configure monitor session for virtual switches
Syntax:
sessionsession
Session name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 939
M Commandsmonitor virtual
mtu-ignoremtu-ignore
Description: Disable OSPF MTU mismatch detection
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# mtu-ignore
mtu-ignore
Description: Disable OSPF MTU mismatch detection
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# mtu-ignore
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)940
M Commandsmtu-ignore
mtumtu <1500-9216>
Description: Set the MTU for this class of service
Syntax:
MTU value<1500-9216>
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# mtu <1500-9216>
mtu <NUMBER>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
Interface MTU. Number range from=576 to=9000<576-9000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# mtu <NUMBER>
mtu <NUMBER>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
Interface MTU. Number range from=576 to=9000<576-9000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 941
M Commandsmtu
(config-leaf-if)# mtu <NUMBER>
mtu <NUMBER>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
Interface MTU. Number range from=576 to=9000<576-9000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# mtu <NUMBER>
mtu <NUMBER>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
Interface MTU. Number range from=576 to=9000<576-9000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# mtu <NUMBER>
mtu <arg>
Description: Update MTU value in Netflow Node-policy
Syntax:
ConfigureMTUvalue in NetflowNode-policy. Number range from=576to=9216
arg
Command Mode: flow node-policy : Configure Netflow Node Policy Parameters
Command Path:
# configure [['terminal', 't']](config)# flow node-policy <WORD>(config-flow-node-pol)# mtu <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)942
M Commandsmtu
mtu <mtu>
Description:MTU size
Syntax:
mtu value. Number range from=64 to=9216mtu
Command Mode: destination tenant : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# mtu <mtu>
mtu <mtu>
Description:MTU size
Syntax:
mtu value. Number range from=64 to=9216mtu
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# mtu <mtu>
mtu <arg>
Description:MTU size
Syntax:
mtu value. Number range from=64 to=9216arg
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <WORD>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-tenant-dest)# mtu <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 943
M Commandsmtu
mtu <arg>
Description: Configure MTU size
Syntax:
MTU value. Number range from=64 to=9216arg
Command Mode: destination destip : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# mtu <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)944
M Commandsmtu
multi-destinationmulti-destination <WORD>
Description: Change behavior for multi destination flood
Syntax:
Unknown multicast MAC and Broadcast handlingWORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# multi-destination <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 945
M Commandsmulti-destination
multi-site-mac-addressmulti-site-mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure multi-site MAC address
Syntax:
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# multi-site-mac-addressE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)946
M Commandsmulti-site-mac-address
multicast-addressmulticast-address <IP>
Description: Configure outgoing multicast IP address for VXLAN modes
Syntax:
Multicast IPIP
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# multicast-address <IP>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 947
M Commandsmulticast-address
multipliermultiplier <NUMBER>
Description: Configure BFD MULTIPLIER value
Syntax:
BFD interval. Number range from=1 to=50<interval>
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# multiplier <NUMBER>
multiplier <NUMBER>
Description: Configure detection multiplier
Syntax:
Detection multiplier. Number range from=1 to=50<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# multiplier <NUMBER>
multiplier <NUMBER>
Description: Configure detection multiplier
Syntax:
Detection multiplier. Number range from=1 to=50<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bfd <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)948
M Commandsmultiplier
(config-template-bfd-pol)# multiplier <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 949
M Commandsmultiplier
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)950
M Commandsmultiplier
N Commands
• name-alias, page 952
• name-lookup, page 956
• name, page 957
• negotiate, page 958
• neighbor-discovery, page 961
• neighbor, page 962
• network, page 964
• next-hop-self, page 965
• node-control, page 966
• npv, page 967
• npv auto-load-balance, page 968
• npv traffic-map external-interface vfc-po, page 969
• npv traffic-map external-interface vfc, page 971
• npv traffic-map server-interface vfc-po, page 972
• npv traffic-map server-interface vfc, page 974
• ntp, page 976
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 951
name-aliasname-alias <WORD>
Description: Add an Alias to a tenant
Syntax:
Alias Of the mo (Max Size 63)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# name-alias <WORD>
name-alias <WORD>
Description: Add an Alias to a access-list
Syntax:
Alias Of the mo (Max Size 63)WORD
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# name-alias <WORD>
name-alias <WORD>
Description: Add an Alias to a contract
Syntax:
Alias Of the mo (Max Size 63)WORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)952
N Commandsname-alias
(config-tenant-contract)# name-alias <WORD>
name-alias <WORD>
Description: Add an Alias to a subject
Syntax:
Alias Of the mo (Max Size 63)WORD
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# name-alias <WORD>
name-alias <WORD>
Description: Add an Alias to vrf
Syntax:
Alias Of the mo (Max Size 63)WORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# name-alias <WORD>
name-alias <WORD>
Description: Add an Alias to l3out
Syntax:
Alias Of the mo (Max Size 63)WORD
Command Mode: l3out : Configuration for L3Out
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l3out <WORD>(config-tenant-l3out)# name-alias <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 953
N Commandsname-alias
name-alias <WORD>
Description: Add an Alias to a bridge-domain
Syntax:
Alias Of the mo (Max Size 63)WORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# name-alias <WORD>
name-alias <WORD>
Description: Add an Alias to Application profile
Syntax:
Alias Of the mo (Max Size 63)WORD
Command Mode: application : application configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# name-alias <WORD>
name-alias <WORD>
Description: Add an Alias to EPG
Syntax:
Alias (Max Size 63)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# name-alias <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)954
N Commandsname-alias
name-alias <WORD>
Description: Add an Alias to l3out
Syntax:
Alias Of the mo (Max Size 63)WORD
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# name-alias <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 955
N Commandsname-alias
name-lookupname-lookup
Description: Display OSPF router ids as DNS names
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# name-lookup
name-lookup
Description: Display OSPF router ids as DNS names
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# name-lookup
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)956
N Commandsname-lookup
namename <WORD>
Description: Redundancy name string
Syntax:
Name string (Max Size 250)WORD
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# name <WORD>
name <WORD>
Description: Redundancy name string
Syntax:
Name string (Max Size 250)WORD
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 957
N Commandsname
negotiatenegotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# negotiate auto
negotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# negotiate auto
negotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: template spine-interface-policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template spine-interface-policy-group <WORD>(config-spine-if-pol-grp)# negotiate auto
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)958
N Commandsnegotiate
negotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# negotiate auto
negotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# negotiate auto
negotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# negotiate auto
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 959
N Commandsnegotiate
negotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# negotiate auto
negotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# negotiate auto
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)960
N Commandsnegotiate
neighbor-discoveryneighbor-discovery
Description: Config trust neighbor discovery protocol in trust control policy
Command Mode: trust-control : Configuration for trust control policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# trust-control <WORD>(config-tenant-fhs-trustctrl)# neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 961
N Commandsneighbor-discovery
neighborneighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out <WORD>]
Description: Configure a BGP neighbor
Syntax:
IP address of the neighborA.B.C.D
IP prefix for neighborsA.B.C.D/LEN
IPv6 address of the neighborA:B::C:D
IPv6 prefix for neighborsA:B::C:D/LEN
(Optional) Make this a shared EVPN BGP session for GOLFevpn
(Optional) Route-Map Name (API-configured L3Out Name)WORD
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>]
neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out <WORD>]
Description: Configure a BGP neighbor
Syntax:
IP address of the neighborA.B.C.D
IP prefix for neighborsA.B.C.D/LEN
IPv6 address of the neighborA:B::C:D
IPv6 prefix for neighborsA:B::C:D/LEN
(Optional) Make this a shared EVPN BGP session for GOLFevpn
(Optional) Route-Map Name (API-configured L3Out Name)WORD
Command Mode: vrf : Virtual Router Context
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)962
N Commandsneighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 963
N Commandsneighbor
networknetwork bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# network bcast|p2p|unspecified
network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# network bcast|p2p|unspecified
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)964
N Commandsnetwork
next-hop-selfnext-hop-self
Description: Set our peering address as nexthop
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# next-hop-self
next-hop-self
Description: Set our peering address as nexthop
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# next-hop-self
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 965
N Commandsnext-hop-self
node-controlnode-control policy <WORD>
Description: Create a Node Control Policy
Syntax:
Create a node control policypolicy
Node control policy name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# node-control policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)966
N Commandsnode-control
npvnpv auto-load-balance disruptive
Description: Configure auto load balancing on the switch
Syntax:
Configure auto load balancingauto-load-balance
Configure disruptive load balancingdisruptive
Command Mode: template fc-leaf-policy : Configure FC Leaf Policy(Max Size 64)
Command Path:
# configure [['terminal', 't']](config)# template fc-leaf-policy <WORD>(config-fc-leaf-policy)# npv auto-load-balance disruptive
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 967
N Commandsnpv
npv auto-load-balancenpv auto-load-balance disruptive
Description: Configure auto load balancing
Syntax:
Configure disruptive load balancingdisruptive
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# npv auto-load-balance disruptive
npv auto-load-balance disruptive
Description: Configure auto load balancing
Syntax:
Configure disruptive load balancingdisruptive
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# npv auto-load-balance disruptive
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)968
N Commandsnpv auto-load-balance
npv traffic-map external-interface vfc-ponpv traffic-map external-interface vfc-po <ifRange> tenant <WORD> label <WORD>
Description: VFC Port Channel interface
Syntax:
Port-channel name<ifRange>
Tenant nametenant
Tenant hosting the pinning Profile (Max Size 63)WORD
Pinning labellabel
Pinning Profile Name (Max Size 64)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# npv traffic-map external-interface vfc-po <ifRange> tenant <WORD> label<WORD>
npv traffic-map external-interface vfc-po <ifRange> tenant <WORD> label <WORD>
Description: VFC Port Channel interface
Syntax:
Port-channel name<ifRange>
Tenant nametenant
Tenant hosting the pinning Profile (Max Size 63)WORD
Pinning labellabel
Pinning Profile Name (Max Size 64)WORD
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# npv traffic-map external-interface vfc-po <ifRange> tenant <WORD> label
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 969
N Commandsnpv traffic-map external-interface vfc-po
<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)970
N Commandsnpv traffic-map external-interface vfc-po
npv traffic-map external-interface vfcnpv traffic-map external-interface vfc <ifRange> tenant <WORD> label <WORD>
Description: Virtual Fiber Channel interface
Syntax:
interface Range<ifRange>
Tenant nametenant
Tenant hosting the pinning Profile (Max Size 63)WORD
Pinning labellabel
Pinning Profile Name (Max Size 64)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# npv traffic-map external-interface vfc <ifRange> tenant <WORD> label <WORD>
npv traffic-map external-interface vfc <ifRange> tenant <WORD> label <WORD>
Description: Virtual Fiber Channel interface
Syntax:
interface Range<ifRange>
Tenant nametenant
Tenant hosting the pinning Profile (Max Size 63)WORD
Pinning labellabel
Pinning Profile Name (Max Size 64)WORD
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# npv traffic-map external-interface vfc <ifRange> tenant <WORD> label <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 971
N Commandsnpv traffic-map external-interface vfc
npv traffic-map server-interface vfc-ponpv traffic-map server-interface vfc-po <WORD> label <WORD> tenant <WORD> application <WORD> epg<WORD>
Description: VFC Port Channel interface
Syntax:
Port-Channel Name (Max Size 64)WORD
Pinning labellabel
Pinning Label Name (Max Size 64)WORD
Tenant nametenant
Tenant hosting the pinning Label (Max Size 63)WORD
Add an AEPg as static encapapplication
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# npv traffic-map server-interface vfc-po <WORD> label <WORD> tenant <WORD>application <WORD> epg <WORD>
npv traffic-map server-interface vfc-po <WORD> label <WORD> tenant <WORD> application <WORD> epg<WORD>
Description: VFC Port Channel interface
Syntax:
Port-Channel Name (Max Size 64)WORD
Pinning labellabel
Pinning Label Name (Max Size 64)WORD
Tenant nametenant
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)972
N Commandsnpv traffic-map server-interface vfc-po
Tenant hosting the pinning Label (Max Size 63)WORD
Add an AEPg as static encapapplication
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# npv traffic-map server-interface vfc-po <WORD> label <WORD> tenant <WORD>application <WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 973
N Commandsnpv traffic-map server-interface vfc-po
npv traffic-map server-interface vfcnpv traffic-map server-interface vfc <ifRange> label <WORD> tenant <WORD> application <WORD> epg<WORD>
Description: Virtual Fiber Channel interface
Syntax:
interface Range<ifRange>
Pinning labellabel
Pinning Label Name (Max Size 64)WORD
Tenant nametenant
Tenant hosting the pinning Label (Max Size 63)WORD
Add an AEPg as static encapapplication
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# npv traffic-map server-interface vfc <ifRange> label <WORD> tenant <WORD>application <WORD> epg <WORD>
npv traffic-map server-interface vfc <ifRange> label <WORD> tenant <WORD> application <WORD> epg<WORD>
Description: Virtual Fiber Channel interface
Syntax:
interface Range<ifRange>
Pinning labellabel
Pinning Label Name (Max Size 64)WORD
Tenant nametenant
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)974
N Commandsnpv traffic-map server-interface vfc
Tenant hosting the pinning Label (Max Size 63)WORD
Add an AEPg as static encapapplication
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# npv traffic-map server-interface vfc <ifRange> label <WORD> tenant <WORD>application <WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 975
N Commandsnpv traffic-map server-interface vfc
ntpntp
Description: Configure the default ntp policy
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# ntp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)976
N Commandsntp
O Commands
• oob-mgmt, page 978
• oob-mgmt epg, page 979
• optimize, page 980
• option, page 981
• org-name, page 982
• org-unit-name, page 983
• other-config-check, page 984
• other-config-flag, page 985
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 977
oob-mgmtoob-mgmt epg <epgval>
Description: Creates/Modify the out of band mgmt under the tenant mgmt
Syntax:
epg is keyword ,refers to out of band epgepg
epg name for the out of band epg created/modified under tenant mgmtepgval
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)978
O Commandsoob-mgmt
oob-mgmt epgoob-mgmt epg <WORD>
Description: Associate node to a Out of band EPG
Syntax:
Out of band End Point Group NameWORD
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# oob-mgmt epg <WORD>
oob-mgmt epg <WORD>
Description: Associate node to a Out of band EPG
Syntax:
Out of band End Point Group NameWORD
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# oob-mgmt epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 979
O Commandsoob-mgmt epg
optimizeoptimize subinterface
Description: Disable sub-interface optimization
Syntax:
subinterfacesubinterface
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# optimize subinterface
optimize subinterface
Description: Disable sub-interface optimization
Syntax:
subinterfacesubinterface
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# optimize subinterface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)980
O Commandsoptimize
optionoption <WORD> id <NUMBER> [data <WORD>]
Description: Add or modify an existing DHCP option when relayed from the server to the client
Syntax:
Name of the option to add (Max Size 64)WORD
ID of the optionid
ID of the option. Number range from=0 to=255<0-255>
(Optional) Body of the Option TLV as hex string, surrounded by singlequotes ex: 'foo*' (Max Size 256)
WORD
Command Mode: template dhcp option : Create a DHCP Option policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp option policy <WORD>(config-tenant-template-dhcp-option)# option <WORD> id <NUMBER> [data <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 981
O Commandsoption
org-nameorg-name <WORD>
Description: Set The full legal name of the organization.
Syntax:
legal name of organization (Max Size 64)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# org-name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)982
O Commandsorg-name
org-unit-nameorg-unit-name <WORD>
Description: Set the department or unit name within the organization
Syntax:
department or unit name (Max Size 64)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# org-unit-name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 983
O Commandsorg-unit-name
other-config-checkother-config-check
Description: Enable other stateful configuration check in router advertisement guard policy
Command Mode: router-advertisement-guard : Configuration for router advertisement guard policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>(config-tenant-fhs-secpol)# router-advertisement-guard(config-tenant-fhs-raguard)# other-config-check
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)984
O Commandsother-config-check
other-config-flagother-config-flag
Description: Set other stateful configuration flag in router advertisement guard policy
Command Mode: router-advertisement-guard : Configuration for router advertisement guard policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>(config-tenant-fhs-secpol)# router-advertisement-guard(config-tenant-fhs-raguard)# other-config-flag
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 985
O Commandsother-config-flag
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)986
O Commandsother-config-flag
P Commands
• passive-interface, page 989
• passphrase, page 990
• passwd, page 991
• password, page 992
• password change-count, page 994
• password change-during-interval, page 995
• password change-interval, page 996
• password change-password, page 997
• password history-count, page 998
• password no-change-interval, page 999
• password pwd-rules, page 1000
• password pwd-strength-check, page 1001
• path, page 1002
• pause, page 1003
• peer-dead-interval, page 1004
• periodic-inventory notification, page 1005
• phone-contact, page 1006
• phone, page 1007
• pod-profile, page 1008
• pod, page 1009
• pods, page 1010
• policy-group, page 1011
• policy-map type control-plane-if, page 1013
• policy-map type control-plane-leaf, page 1014
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 987
• policy-map type control-plane-spine, page 1015
• policy-map type data-plane, page 1016
• policy-map type port-authentication, page 1017
• policy-map type qos, page 1018
• port-authentication, page 1019
• port-authentication fail-auth-epg, page 1020
• port-authentication fail-auth-vlan, page 1022
• port-authentication radius-provider-group, page 1023
• port, page 1024
• porttrack delay, page 1027
• porttrack minlinks, page 1028
• porttrack state, page 1029
• power, page 1030
• preempt, page 1031
• preempt delay, page 1032
• prefix-suppression, page 1034
• preview, page 1035
• priority-flow-control, page 1036
• priority, page 1039
• priv-type, page 1042
• priv, page 1043
• private-as-control, page 1044
• profile-type, page 1045
• protocol, page 1047
• protocol bps, page 1048
• provider, page 1049
• proxy-arp, page 1050
• ptp, page 1051
• pwd-lifetime, page 1052
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)988
P Commands
passive-interfacepassive-interface
Description: Suppress routing updates on the interface
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# passive-interface
passive-interface
Description: Suppress routing updates on the interface
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# passive-interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 989
P Commandspassive-interface
passphrasepassphrase
Description: Configure passphrase for AES encryption
Command Mode: crypto aes : AES encryption configuration
Command Path:
# configure [['terminal', 't']](config)# crypto aes(config-aes)# passphrase
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)990
P Commandspassphrase
passwdpasswd
Description: Update user's authentication tokens
Command Mode: exec : Exec Mode
Command Path:
# passwd
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 991
P Commandspasswd
passwordpassword
Description: Set The system user password.
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# password
password
Description: Set The new password.
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# password
password WORD
Description: Configure a password for neighbor
Syntax:
Enter Clear-text passwordWORD
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# password WORD
password WORD
Description: Configure a password for neighbor
Syntax:
Enter Clear-text passwordWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)992
P Commandspassword
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# password WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 993
P Commandspassword
password change-countpassword change-count <NUMBER>
Description: Set the number of password changes allowed within change interval
Syntax:
Set the number of password changes allowed within change interval.Number range from=0 to=10
<0-10>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password change-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)994
P Commandspassword change-count
password change-during-intervalpassword change-during-interval <change-during-interval>
Description: Set change count/interval policy selector for enforcing password change.
Syntax:
<change-during-interval><change-during-interval>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password change-during-interval <change-during-interval>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 995
P Commandspassword change-during-interval
password change-intervalpassword change-interval <NUMBER>
Description: Set time interval for limiting the number of password changes (unit: Hours)
Syntax:
Set A time interval for limiting the number of password changes (unit:Hours). Number range from=1 to=745
<1-745>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password change-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)996
P Commandspassword change-interval
password change-passwordpassword change-password
Description: change the current password and set a new one
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password change-password
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 997
P Commandspassword change-password
password history-countpassword history-count <NUMBER>
Description: Set number of retired passwords to store in user's history.
Syntax:
Set number of retired passwords to store in user history.. Number rangefrom=0 to=15
<0-15>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password history-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)998
P Commandspassword history-count
password no-change-intervalpassword no-change-interval <NUMBER>
Description: Set minimum period before which user cannot change password again (unit: hours)
Syntax:
Set minimum period before which user cannot change password again(unit: hours). Number range from=1 to=745
<1-745>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password no-change-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 999
P Commandspassword no-change-interval
password pwd-rulespassword pwd-rules minimum-length <minimum-length> maximum-length <maximum-length> pwd-ruledefault|custom custom-password-class ULD|ULSp|UDSp|LDSp|ULDSp
Description: Enables the configuration of password rules
Syntax:
Minimum Password Lengthminimum-length
Minimum Password Length( > = 8)<minimum-length>
Maximum Password Lengthmaximum-length
Maximum Password Length(< = 64<maximum-length>
Password Rulepwd-rule
Use system default password rulesdefault
Use custom password rulescustom
Custom Password Classcustom-password-class
Uppercase-Lowercase-DigitULD
Uppercae-Lowercase-SpecialcharULSp
Uppercase-Digit-SpecialcharUDSp
Lowercase-Digit-SpecialcharLDSp
Uppercase-Lowercase-Digit-SpecialcharULDSp
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password pwd-rules minimum-length <minimum-length> maximum-length <maximum-length>pwd-rule default|custom custom-password-class ULD|ULSp|UDSp|LDSp|ULDSp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1000
P Commandspassword pwd-rules
password pwd-strength-checkpassword pwd-strength-check
Description: Enforces the strength of password for all users
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password pwd-strength-check
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1001
P Commandspassword pwd-strength-check
pathpath ftp|sftp|scp <HOST> [port <NUMBER>] [remote-directory <PATH>]
Description: Configure remote path properties
Syntax:
FTPftp
Secure FTPsftp
Secure copyscp
Remote host name or IP addressHOST
(Optional) Remote port. Number range from=0 to=65535<0-65535>
(Optional) Remote directory: path/to/some/dirPATH
Command Mode: remote : Remote path configuration mode
Command Path:
# configure [['terminal', 't']](config)# remote path <WORD>(config-remote)# path ftp|sftp|scp <HOST> [port <NUMBER>] [remote-directory <PATH>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1002
P Commandspath
pausepause no-drop cos <NUMBER>
Description: Configure class based flow control characteristics
Syntax:
Configure class based flow control charactersticsno-drop
Configure class of servicecos
Configure class of service. Number range from=0 to=7<interval>
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# pause no-drop cos <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1003
P Commandspause
peer-dead-intervalpeer-dead-interval <NUMBER>
Description: Configure Peer dead Interval
Syntax:
Peer dead Interval value. Number range from=5 to=600<5-600>
Command Mode: vpc domain explicit : Pair two leaf nodes explicitly
Command Path:
# configure [['terminal', 't']](config)# vpc domain explicit <NUMBER> leaf <101-4000> <101-4000>(config-vpc)# peer-dead-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1004
P Commandspeer-dead-interval
periodic-inventory notificationperiodic-inventory notification schedule <schedName>
Description: Configure periodic notifications Parameters
Syntax:
Configure periodic notification schedulerschedule
scheduler name<schedName>
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# periodic-inventory notification schedule <schedName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1005
P Commandsperiodic-inventory notification
phone-contactphone-contact <WORD>
Description: The contact phone number
Syntax:
Phone number in international format(such as +1-800-123-4567) (MaxSize 16)
WORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# phone-contact <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1006
P Commandsphone-contact
phonephone <WORD>
Description: Set The phone number of the locally-authenticated user.
Syntax:
phone number (Max Size 16)WORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# phone <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1007
P Commandsphone
pod-profilepod-profile <WORD>
Description: POD Profile
Syntax:
Pod Profile Name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# pod-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1008
P Commandspod-profile
podpod <NUMBER>
Description: Pod configuration mode
Syntax:
Enter Pod ID. Number range from=1 to=1<1-1>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>
pod <NUMBER>
Description: Pod Profile
Syntax:
Pod ID. Number range from=1 to=255<ID>
Command Mode: fabric-external : Intrasite/Intersite Connectivity Profile
Command Path:
# configure [['terminal', 't']](config)# fabric-external <NUMBER>(config-fabric-external)# pod <NUMBER>
pod <1-255>
Description: Add pods to zone
Syntax:
Range of Pods<1-255>
Command Mode: zone : Create zone policy
Command Path:
# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>(config-zone)# pod <1-255>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1009
P Commandspod
podspods <1-255>
Description: Set of PODs
Syntax:
Range of Pods<1-255>
Command Mode: pod-profile : POD Profile
Command Path:
# configure [['terminal', 't']](config)# pod-profile <WORD>(config-pod-profile)# pods <1-255>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1010
P Commandspods
policy-grouppolicy-group <WORD>
Description: Associate an Interface Policy Group to this Interface Group
Syntax:
Interface Policy Group Name (Max Size 64)WORD
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# policy-group <WORD>
policy-group <WORD>
Description: Configure Policy Group on the Fex
Syntax:
Interface Policy Group Name (Max Size 64)WORD
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# policy-group <WORD>
policy-group <WORD> [force]
Description: Configure Leaf Interface Policy Group
Syntax:
Interface Policy Group Name (Max Size 64)WORD
(Optional) Delete Per Port Configuration and apply the existingpolicy-group config
force
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1011
P Commandspolicy-group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# policy-group <WORD> [force]
policy-group <WORD> [force]
Description: Configure Leaf Interface Policy Group
Syntax:
Interface Policy Group Name (Max Size 64)WORD
(Optional) Delete Per Port Configuration and apply the existingpolicy-group config
force
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# policy-group <WORD> [force]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1012
P Commandspolicy-group
policy-map type control-plane-ifpolicy-map type control-plane-if <WORD>
Description: Create interface ControlPlane policy to police/reclassify the traffic
Syntax:
Name of the policy-map to add (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# policy-map type control-plane-if <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1013
P Commandspolicy-map type control-plane-if
policy-map type control-plane-leafpolicy-map type control-plane-leaf <WORD>
Description: Create leaf aggregate ControlPlane policy to police/reclassify the traffic
Syntax:
Name of the policy-map to add (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# policy-map type control-plane-leaf <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1014
P Commandspolicy-map type control-plane-leaf
policy-map type control-plane-spinepolicy-map type control-plane-spine <WORD>
Description: Create spine aggregate ControlPlane policy to police/reclassify the traffic
Syntax:
Name of the policy-map to add (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# policy-map type control-plane-spine <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1015
P Commandspolicy-map type control-plane-spine
policy-map type data-planepolicy-map type data-plane <WORD>
Description: Create a policymap of DataPlane type to police/reclassify the traffic
Syntax:
Name of the policy-map to add (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>
policy-map type data-plane <WORD>
Description: data-plane policy type
Syntax:
Policy Typetype
Name of the policy-map to add (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1016
P Commandspolicy-map type data-plane
policy-map type port-authenticationpolicy-map type port-authentication <WORD>
Description: Create node level port authentication policy
Syntax:
Port authentication Policy Group Name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# policy-map type port-authentication <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1017
P Commandspolicy-map type port-authentication
policy-map type qospolicy-map type qos <WORD>
Description: QOS policy type
Syntax:
Policy Typetype
Name of the policy-map to add (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type qos <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1018
P Commandspolicy-map type qos
port-authenticationport-authentication <WORD>
Description: Add port authentication policy
Syntax:
Port authentication Policy Group Name (Max Size 64)WORD
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# port-authentication <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1019
P Commandsport-authentication
port-authentication fail-auth-epgport-authentication fail-auth-epg tenant <arg> application <arg> epg <arg>
Description: Set default EPg name if authentication fails
Syntax:
Tenant hosting the EPgtenant
arg
Application Nameapplication
arg
Deploy EPg if authentication failsepg
arg
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# port-authentication fail-auth-epg tenant <> application <> epg <>
port-authentication fail-auth-epg tenant <arg> application <arg> epg <arg>
Description: Set default EPg name if authentication fails
Syntax:
Tenant hosting the EPgtenant
arg
Application Nameapplication
arg
Deploy EPg if authentication failsepg
arg
Command Mode: spine : Configure Spine Node
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1020
P Commandsport-authentication fail-auth-epg
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# port-authentication fail-auth-epg tenant <> application <> epg <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1021
P Commandsport-authentication fail-auth-epg
port-authentication fail-auth-vlanport-authentication fail-auth-vlan <vlan-id>
Description: Set default vlan encap if authentication fails
Syntax:
Configure Vlan ID<vlan-id>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# port-authentication fail-auth-vlan <vlan-id>
port-authentication fail-auth-vlan <vlan-id>
Description: Set default vlan encap if authentication fails
Syntax:
Configure Vlan ID<vlan-id>
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# port-authentication fail-auth-vlan <vlan-id>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1022
P Commandsport-authentication fail-auth-vlan
port-authentication radius-provider-groupport-authentication radius-provider-group <arg>
Description: Set radius provider group
Syntax:
arg
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# port-authentication radius-provider-group <>
port-authentication radius-provider-group <arg>
Description: Set radius provider group
Syntax:
arg
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# port-authentication radius-provider-group <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1023
P Commandsport-authentication radius-provider-group
portport <NUMBER>
Description: LDAP server port for authentication
Syntax:
Port number. Number range from=1 to=65535<1-65535>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# port <NUMBER>
port <NUMBER>
Description: RADIUS server port for authentication
Syntax:
RADIUS server port for authentication. Number range from=1 to=65535<1-65535>
Command Mode: radius-server host : RADIUS server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# port <NUMBER>
port <NUMBER>
Description: TACACS server port for authentication
Syntax:
RADIUS server port for authentication. Number range from=1 to=65535<1-65535>
Command Mode: tacacs-server host : TACACS+ server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# port <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1024
P Commandsport
port <NUMBER>
Description: Set the port used for SSH communication service.
Syntax:
Set the port used for SSH communication service.. Number rangefrom=0 to=65535
<0-65535>
Command Mode: ssh-service : SSH communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# ssh-service(config-ssh-service)# port <NUMBER>
port <NUMBER>
Description: Set the port used for TELNET communication service.
Syntax:
Set the port used for TELNET communication service.. Number rangefrom=0 to=65535
<0-65535>
Command Mode: telnet : TELNET communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# telnet(config-telnet)# port <NUMBER>
port <NUMBER>
Description: Set the port used for HTTP communication service.
Syntax:
Set the port used for HTTP communication service.. Number rangefrom=1 to=65535
<1-65535>
Command Mode: http : HTTP communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# port <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1025
P Commandsport
port <NUMBER>
Description: Set the port used for HTTPS communication service
Syntax:
Set the port used for HTTPS communication service. Number rangefrom=1 to=65535
<1-65535>
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# port <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1026
P Commandsport
porttrack delayporttrack delay <1-300>
Description: Set Port Tracking Delay
Syntax:
Delay value<1-300>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# porttrack delay <1-300>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1027
P Commandsporttrack delay
porttrack minlinksporttrack minlinks <0-12>
Description: Set Port Tracking minimum links left up before trigger
Syntax:
Minlinks Value<0-12>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# porttrack minlinks <0-12>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1028
P Commandsporttrack minlinks
porttrack stateporttrack state on
Description: Set Port Tracking State
Syntax:
To enable port tracking stateon
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# porttrack state on
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1029
P Commandsporttrack state
powerpower redundancy-policy <WORD>
Description: Create a power supply redundancy policy
Syntax:
Create a power supply redundancy policyredundancy-policy
Power supply redundancy policy name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# power redundancy-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1030
P Commandspower
preemptpreempt
Description: Overthrow lower priority Active routers
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# preempt
preempt
Description: Overthrow lower priority Active routers
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# preempt
preempt
Description: Overthrow lower priority Active routers
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# preempt
preempt
Description: Overthrow lower priority Active routers
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# preempt
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1031
P Commandspreempt
preempt delaypreempt delay minimum|reload|sync <NUMBER>
Description:Wait before preempting
Syntax:
Delay at least this longminimum
Delay after reloadreload
Wait for IP redundancy clientssync
Delay in seconds. Number range from=0 to=3600<0-3600>
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# preempt delay minimum|reload|sync <NUMBER>
preempt delay minimum|reload|sync <NUMBER>
Description:Wait before preempting
Syntax:
Delay at least this longminimum
Delay after reloadreload
Wait for IP redundancy clientssync
Delay in seconds. Number range from=0 to=3600<0-3600>
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# preempt delay minimum|reload|sync <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1032
P Commandspreempt delay
preempt delay minimum|reload|sync <NUMBER>
Description:Wait before preempting
Syntax:
Delay at least this longminimum
Delay after reloadreload
Wait for IP redundancy clientssync
Delay in seconds. Number range from=0 to=3600<0-3600>
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# preempt delay minimum|reload|sync <NUMBER>
preempt delay minimum|reload|sync <NUMBER>
Description:Wait before preempting
Syntax:
Delay at least this longminimum
Delay after reloadreload
Wait for IP redundancy clientssync
Delay in seconds. Number range from=0 to=3600<0-3600>
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# preempt delay minimum|reload|sync <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1033
P Commandspreempt delay
prefix-suppressionprefix-suppression
Description: Suppress prefixes
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# prefix-suppression
prefix-suppression
Description: Suppress prefixes
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# prefix-suppression
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1034
P Commandsprefix-suppression
previewpreview
Description: Rollback preview mode
Command Mode: snapshot rollback : Configuration rollback setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot rollback <WORD>(config-rollback)# preview
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1035
P Commandspreview
priority-flow-controlpriority-flow-control mode <arg>
Description: Configure Pfc Policy
Syntax:
Pfc policy modemode
arg
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# priority-flow-control mode <>
priority-flow-control mode <arg>
Description: Configure Pfc Policy
Syntax:
Pfc policy modemode
arg
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# priority-flow-control mode <>
priority-flow-control mode <arg>
Description: Configure Interface pfc policy
Syntax:
Pfc policy modemode
arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1036
P Commandspriority-flow-control
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# priority-flow-control mode <>
priority-flow-control mode <arg>
Description: Configure Interface pfc policy
Syntax:
Pfc policy modemode
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# priority-flow-control mode <>
priority-flow-control mode <arg>
Description: Configure Interface pfc policy
Syntax:
Pfc policy modemode
arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# priority-flow-control mode <>
priority-flow-control mode <arg>
Description: Configure Interface pfc policy
Syntax:
Pfc policy modemode
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1037
P Commandspriority-flow-control
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# priority-flow-control mode <>
priority-flow-control mode <arg>
Description: Configure Interface pfc policy
Syntax:
Pfc policy modemode
arg
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# priority-flow-control mode <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1038
P Commandspriority-flow-control
prioritypriority <NUMBER>
Description: Router priority
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# priority <NUMBER>
priority <NUMBER>
Description: Priority level
Syntax:
Priority value. Number range from=0 to=255<0-255>
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# priority <NUMBER>
priority <NUMBER>
Description: Priority level
Syntax:
Priority value. Number range from=0 to=255<0-255>
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1039
P Commandspriority
(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']](config-if-hsrp)# priority <NUMBER>
priority <NUMBER>
Description: Router priority
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# priority <NUMBER>
priority <NUMBER>
Description: Priority level
Syntax:
Priority value. Number range from=0 to=255<0-255>
Command Mode: template hsrp group-policy : Configure HSRP Group policy templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template hsrp group-policy <WORD> tenant <WORD>(config-template-hsrp-group-pol)# priority <NUMBER>
priority <NUMBER>
Description: Priority level
Syntax:
Priority value. Number range from=0 to=255<0-255>
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1040
P Commandspriority
(config-if-hsrp)# priority <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1041
P Commandspriority
priv-typepriv-type <privType>
Description: Set the AAA domain role to set privilege bitmask of a user domain
Syntax:
<privType><privType>
Command Mode: role : Create the AAA domain role to set privilege bitmask of a user domain
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# domain <WORD>(config-domain)# role <WORD>(config-role)# priv-type <privType>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1042
P Commandspriv-type
privpriv <privileges>
Description: Set privileges (comma separated values)
Syntax:
Privileges as comma separated values like val1,val2,..valN<privileges>
Command Mode: rbac role : Create AAA role, attributes and privileges for user authorization
Command Path:
# configure [['terminal', 't']](config)# rbac role <WORD>(config-role)# priv <privileges>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1043
P Commandspriv
private-as-controlprivate-as-control remove-exclusive|remove-exclusive-all|remove-exclusive-all-replace-as
Description: Private AS Control
Syntax:
Remove private ASremove-exclusive
Remove all private ASremove-exclusive-all
Replace private AS with local ASremove-exclusive-all-replace-as
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# private-as-controlremove-exclusive|remove-exclusive-all|remove-exclusive-all-replace-as
private-as-control remove-exclusive|remove-exclusive-all|remove-exclusive-all-replace-as
Description: Private AS Control
Syntax:
Remove private ASremove-exclusive
Remove all private ASremove-exclusive-all
Replace private AS with local ASremove-exclusive-all-replace-as
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# private-as-controlremove-exclusive|remove-exclusive-all|remove-exclusive-all-replace-as
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1044
P Commandsprivate-as-control
profile-typeprofile-type <arg>
Description: Leaf aggregate policy for Control Plane Policing
Syntax:
Aggregate Profilearg
Command Mode: policy-map type control-plane-leaf : Create leaf aggregate ControlPlane policy topolice/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type control-plane-leaf <WORD>(config-pmap-copp-leaf)# profile-type <>
profile-type <arg>
Description: Spine aggregate policy for Control Plane Policing
Syntax:
Aggregate Profilearg
Command Mode: policy-map type control-plane-spine : Create spine aggregate ControlPlane policy topolice/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type control-plane-spine <WORD>(config-pmap-copp-spine)# profile-type <>
profile-type <profile-type>
Description: Set profile type for scale profile
Syntax:
Profile Typeprofile-type
Command Mode: scale-profile : Configure Forwarding Scale Profile policy
Command Path:
# configure [['terminal', 't']](config)# scale-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1045
P Commandsprofile-type
(config-scale-profile)# profile-type <profile-type>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1046
P Commandsprofile-type
protocolprotocol <protocol>
Description: RADIUS server protocol for authentication
Syntax:
<protocol><protocol>
Command Mode: radius-server host : RADIUS server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# protocol <protocol>
protocol <WORD>
Description: Set the TACACS+ authentication protocol
Syntax:
TACACS+ authentication protocolWORD
Command Mode: tacacs-server host : TACACS+ server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# protocol <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1047
P Commandsprotocol
protocol bpsprotocol <WORD> bps <arg> [burst-rate <arg>]
Description: Configure Control Plane Policy Level (Byte Per Second)
Syntax:
Policer ModeWORD
Rate in packets per second. Number range from=0 to=4398046510080arg
(Optional) Burst rate in packets per second. Number range from=0to=549755813760
arg
CommandMode: policy-map type control-plane-if : Create interface ControlPlane policy to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type control-plane-if <WORD>(config-pmap-copp-if)# protocol <WORD> bps <> [burst-rate <>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1048
P Commandsprotocol bps
providerprovider epg-label <WORD> [complement]
Description: Add a provider EPG label
Syntax:
EPG labelepg-label
EPG label name (Max Size 64)WORD
(Optional) Set isComplement property of the label to Truecomplement
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# provider epg-label <WORD> [complement]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1049
P Commandsprovider
proxy-arpproxy-arp enable
Description: Enable Proxy ARP
Syntax:
Enable Proxy ARPenable
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# proxy-arp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1050
P Commandsproxy-arp
ptpptp
Description: Configure PTP protocol State
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ptp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1051
P Commandsptp
pwd-lifetimepwd-lifetime <NUMBER>
Description: Set The lifetime of the user password (0 = No password expiration)
Syntax:
lifetime of locally-authenticated user password. Number range from=0to=3650
<0-3650>
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# pwd-lifetime <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1052
P Commandspwd-lifetime
Q Commands
• qinq-static-endpoint, page 1054
• qos, page 1058
• qos parameters, page 1059
• qos preserve, page 1060
• query-profile, page 1061
• query, page 1062
• queue control, page 1063
• queue limit, page 1064
• quota, page 1065
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1053
qinq-static-endpointqinq-static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE outer-vlan <NUMBER>inner-vlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure Silent Host behind an EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Outer Encapsulation Vlanouter-vlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Outer Encapsulation Vlaninner-vlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# qinq-static-endpoint macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE outer-vlan <NUMBER> inner-vlan<NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
qinq-static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE outer-vlan <NUMBER>inner-vlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure silent Host behind an EPG with a Static Path Attachment
Syntax:
MAC addressmac
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1054
Q Commandsqinq-static-endpoint
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Outer Encapsulation Vlanouter-vlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Outer Encapsulation Vlaninner-vlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# qinq-static-endpoint macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE outer-vlan <NUMBER> inner-vlan<NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
qinq-static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE outer-vlan <NUMBER>inner-vlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure Silent Host behind an EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Outer Encapsulation Vlanouter-vlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1055
Q Commandsqinq-static-endpoint
Outer Encapsulation Vlaninner-vlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# qinq-static-endpoint macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE outer-vlan <NUMBER> inner-vlan<NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
qinq-static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE outer-vlan <NUMBER>inner-vlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure silent Host behind an EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Outer Encapsulation Vlanouter-vlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Outer Encapsulation Vlaninner-vlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface port-channel : Port Channel interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1056
Q Commandsqinq-static-endpoint
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# qinq-static-endpoint macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE outer-vlan <NUMBER> inner-vlan<NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
qinq-static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE outer-vlan <NUMBER>inner-vlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure silent Host behind a EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Outer Encapsulation Vlanouter-vlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Outer Encapsulation Vlaninner-vlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# qinq-static-endpoint macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE outer-vlan <NUMBER> inner-vlan<NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1057
Q Commandsqinq-static-endpoint
qosqos dscp-map <WORD>
Description: Set DSCP Class translation values
Syntax:
DSCP mapdscp-map
DSCP Translation Policy name (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# qos dscp-map <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1058
Q Commandsqos
qos parametersqos parameters level1|level2|level3
Description: Configure the global QOS policies
Syntax:
Set parameters for level1level1
Set parameters for level2level2
Set parameters for level3level3
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1059
Q Commandsqos parameters
qos preserveqos preserve cos
Description: Preserve incoming qos value in the frame
Syntax:
IEEE 802.1P class of service.cos
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# qos preserve cos
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1060
Q Commandsqos preserve
query-profilequery-profile
Description: Configure Query profile Parameters
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1061
Q Commandsquery-profile
queryquery <WORD> type dn|class <dn/classname>
Description: Configure Query profile Parameters
Syntax:
Query name (Max Size 16)WORD
typetype
Dndn
Classclass
The class or DN name<dn/classname>
Command Mode: query-profile : Configure Query profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile(config-callhome-queryprof)# query <WORD> type dn|class <dn/classname>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1062
Q Commandsquery
queue controlqueue control dynamic
Description: Set the queueing control method
Syntax:
Dynamic allocation of queue resourcesdynamic
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# queue control dynamic
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1063
Q Commandsqueue control
queue limitqueue limit <1500-9216>
Description: Set the limit for the policing queue
Syntax:
Queue limit size<1500-9216>
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# queue limit <1500-9216>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1064
Q Commandsqueue limit
quotaquota <WORD> max <0-4294967295> [exceed-action <WORD>] [scope <WORD>] [tenant <WORD>][bridge-domain <WORD>] [application <WORD>] [epg <WORD>]
Description: Quota Settings
Syntax:
Name of class to place under quota (Max Size None)WORD
Maximum value above which exceed action is takenmax
Maximum value above which exceed action is taken<0-4294967295>
(Optional) Exceed Action to be taken when max is exceededWORD
(Optional) Subtree where the quota is calculated (Max Size None)WORD
(Optional) Tenant for the quota (Max Size 63)WORD
(Optional) Name of the bridge-domain (Max Size 64)WORD
(Optional) Application name (Max Size 64)WORD
(Optional) Application EPG name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# quota <WORD> max <0-4294967295> [exceed-action <WORD>] [scope <WORD>] [tenant<WORD>] [bridge-domain <WORD>] [application <WORD>] [epg <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1065
Q Commandsquota
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1066
Q Commandsquota
R Commands
• radius-provider-group, page 1069
• radius-server host, page 1070
• radius-server retries, page 1071
• radius-server timeout, page 1072
• rbac role, page 1073
• rbac rule, page 1074
• rbac security-domain, page 1075
• realm, page 1076
• record, page 1077
• recurring, page 1078
• redir-dest, page 1079
• redirect, page 1080
• redistrib-metric, page 1081
• redistribute, page 1082
• redundancy-mode, page 1083
• region, page 1084
• reload controller, page 1085
• reload switch, page 1086
• remote-as, page 1087
• remote, page 1088
• replace-controller replace, page 1090
• replace-controller reset, page 1091
• request-status-count, page 1092
• reset-to-factory, page 1093
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1067
• response-incl, page 1094
• response-subtree, page 1095
• retransmit-interval, page 1096
• retries, page 1097
• reverse-port, page 1098
• revision, page 1099
• role, page 1100
• route-control, page 1101
• route-map, page 1102
• route-profile, page 1105
• route-reflector, page 1106
• route-target, page 1107
• router-advertisement-guard-admin-status, page 1109
• router-advertisement-guard, page 1110
• router-advertisement, page 1111
• router-id, page 1112
• router bgp, page 1114
• router eigrp, page 1115
• router ospf, page 1116
• rtr-cfg, page 1117
• run-mode, page 1118
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1068
R Commands
radius-provider-groupradius-provider-group <arg>
Description: Set radius provider group
Syntax:
arg
Command Mode: policy-map type port-authentication : Create node level port authentication policy
Command Path:
# configure [['terminal', 't']](config)# policy-map type port-authentication <WORD>(config-pmap-port-authentication)# radius-provider-group <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1069
R Commandsradius-provider-group
radius-server hostradius-server host <A.B.C.D|A:B::C:D|WORD>
Description: RADIUS server's DNS name or its IP address
Syntax:
Provide a hostname or IPV4/IPV6 addressA.B.C.D|A:B::C:D|WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1070
R Commandsradius-server host
radius-server retriesradius-server retries <NUMBER>
Description: Global RADIUS server retransmit count
Syntax:
Global RADIUS server retransmit count. Number range from=0 to=5<0-5>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# radius-server retries <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1071
R Commandsradius-server retries
radius-server timeoutradius-server timeout <NUMBER>
Description: Global RADIUS server timeout period in seconds
Syntax:
Global RADIUS server timeout period in seconds. Number range from=1to=60
<1-60>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# radius-server timeout <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1072
R Commandsradius-server timeout
rbac rolerbac role <WORD>
Description: Create AAA role, attributes and privileges for user authorization
Syntax:
Provide AAA Security domain role name (Max Size 32)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# rbac role <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1073
R Commandsrbac role
rbac rulerbac rule <DN> <WORD>
Description: Create RBAC rule, security domain users can read subtree starting at specific object
Syntax:
Provide RBAC Rule ObjectDN stringDN
Provide RBAC Rule domain name (Max Size None)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# rbac rule <DN> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1074
R Commandsrbac rule
rbac security-domainrbac security-domain <WORD>
Description: Create AAA security domain for processing authentication requests.
Syntax:
Provide AAA Security domain name (Max Size 32)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# rbac security-domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1075
R Commandsrbac security-domain
realmrealm <realm>
Description: Specify server realm
Syntax:
<realm><realm>
Command Mode: aaa authentication login console : Configure console methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login console(config-console)# realm <realm>
realm <realm>
Description: Specify server realm
Syntax:
<realm><realm>
Command Mode: aaa authentication login default : Configure default methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login default(config-default)# realm <realm>
realm <realm>
Description: Specify server realm
Syntax:
<realm><realm>
Command Mode: aaa authentication login domain : Configure domain methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login domain <WORD>(config-domain)# realm <realm>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1076
R Commandsrealm
recordrecord <WORD>
Description: Assign Netflow Record to the Monitor
Syntax:
Monitor Name (Max Size 64)WORD
Command Mode: flow monitor : Configure Netflow Monitor
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow monitor <WORD>(config-tn-flow-monitor)# record <WORD>
record <WORD>
Description: Assign Netflow Record to the Monitor
Syntax:
Monitor Name (Max Size 64)WORD
Command Mode: flow monitor : Configure Netflow Monitor
Command Path:
# configure [['terminal', 't']](config)# flow monitor <WORD>(config-flow-monitor)# record <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1077
R Commandsrecord
recurringrecurring window <WORD>
Description: Recurring window configuration mode
Syntax:
Configure a schedule windowwindow
Window name (Max size 31)WORD
Command Mode: scheduler : Scheduler configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1078
R Commandsrecurring
redir-destredir-dest <A.B.C.D|A:B::C:D> <XX:XX:XX:XX:XX:XX>
Description: Set ip and mac for service redirect destination
Syntax:
IP address of the deviceA.B.C.D|A:B::C:D
virtual mac addressXX:XX:XX:XX:XX:XX
Command Mode: svcredir-pol : Configure L4L7 service redirection policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# svcredir-pol <WORD>(svcredir-pol)# redir-dest <A.B.C.D|A:B::C:D> <XX:XX:XX:XX:XX:XX>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1079
R Commandsredir-dest
redirectredirect
Description: Enable the state of the HTTP redirect state
Command Mode: http : HTTP communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# redirect
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1080
R Commandsredirect
redistrib-metricredistrib-metric <NUMBER>
Description: Set the configuration of ISIS metric for redistributed routes
Syntax:
The configuration of ISIS metric for redistributed routes. Number rangefrom=1 to=63
<1-63>
Command Mode: isis : Intermediate System to Intermediate System (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# isis fabric(config-pod-isis)# redistrib-metric <NUMBER>
redistrib-metric <NUMBER>
Description: Set the configuration of ISIS metric for redistributed routes
Syntax:
The configuration of ISIS metric for redistributed routes. Number rangefrom=1 to=63
<1-63>
Command Mode: template isis-fabric : InterSystem-InterSystem Protocol (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# template isis-fabric <WORD>(config-template-isis-fabric)# redistrib-metric <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1081
R Commandsredistrib-metric
redistributeredistribute ospf|eigrp route-map <WORD>
Description: Redistribute route map
Syntax:
Redistribute OSPFospf
Redistribute EIGRPeigrp
Route map to redistribute toroute-map
Route map nameWORD
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# redistribute ospf|eigrp route-map <WORD>
redistribute ospf|eigrp route-map <WORD>
Description: Redistribute route map
Syntax:
Redistribute OSPFospf
Redistribute EIGRPeigrp
Route map to redistribute toroute-map
Route map nameWORD
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# redistribute ospf|eigrp route-map <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1082
R Commandsredistribute
redundancy-moderedundancy-mode combined|ps-redundant|redundant
Description: Configure power supply redundancy mode
Syntax:
Combined mode to use output of all available PScombined
PS redundant mode (N+1) to enable power output redundancyps-redundant
Redundant mode (N+N) for a single PS to power the systemredundant
Command Mode: power : Create a power supply redundancy policy
Command Path:
# configure [['terminal', 't']](config)# power redundancy-policy <WORD>(config-power)# redundancy-mode combined|ps-redundant|redundant
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1083
R Commandsredundancy-mode
regionregion <WORD>
Description: STP MST region configuration mode
Syntax:
MST region nameWORD
Command Mode: spanning-tree : STP MST configuration mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1084
R Commandsregion
reload controllerreload controller <NUMBER>
Description: Reload controller
Syntax:
Controller id. Number range from=1 to=64<1-64>
Command Mode: exec : Exec Mode
Command Path:
# reload controller <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1085
R Commandsreload controller
reload switchreload switch <NUMBER>
Description: Reload switch
Syntax:
Switch id. Number range from=101 to=4000<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# reload switch <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1086
R Commandsreload switch
remote-asremote-as <NUMBER>
Description: Specify Autonomous System Number of the neighbor
Syntax:
The Remote autonomous system number. Number range from=1to=4294967295
<1-4294967295>
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# remote-as <NUMBER>
remote-as <NUMBER>
Description: Specify Autonomous System Number of the neighbor
Syntax:
The Remote autonomous system number. Number range from=1to=4294967295
<1-4294967295>
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# remote-as <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1087
R Commandsremote-as
remoteremote path <WORD>
Description: Remote path configuration mode
Syntax:
Configure remote pathpath
Remote path configuration nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# remote path <WORD>
remote path <WORD>
Description: Set the remote path configuration will get downloaded from
Syntax:
Assign remote pathpath
Remote path nameWORD
Command Mode: snapshot download : Configuration snapshot download setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot download <WORD>(config-download)# remote path <WORD>
remote path <WORD>
Description: Set the remote path configuration will get exported to
Syntax:
Configure remote pathpath
Remote path nameWORD
Command Mode: snapshot export : Configuration export setup mode
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1088
R Commandsremote
Command Path:
# configure [['terminal', 't']](config)# snapshot export <WORD>(config-export)# remote path <WORD>
remote path <WORD>
Description: Set the remote path configuration will get imported from
Syntax:
Assign remote pathpath
Remote path nameWORD
Command Mode: snapshot import : Configuration import setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# remote path <WORD>
remote path <WORD>
Description: Set the remote path configuration will get uploaded to
Syntax:
Assign remote pathpath
Remote path nameWORD
Command Mode: snapshot upload : Configuration snapshot upload setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot upload <WORD>(config-upload)# remote path <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1089
R Commandsremote
replace-controller replacereplace-controller replace <NUMBER> <standby-serial>
Description: Replace active controller with standby
Syntax:
Controller ID. Number range from=1 to=64<1-64>
Backup serial number<standby-serial>
Command Mode: exec : Exec Mode
Command Path:
# replace-controller replace <NUMBER> <standby-serial>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1090
R Commandsreplace-controller replace
replace-controller resetreplace-controller reset <NUMBER>
Description: Reset failover status of controller
Syntax:
Controller ID. Number range from=1 to=64<1-64>
Command Mode: exec : Exec Mode
Command Path:
# replace-controller reset <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1091
R Commandsreplace-controller reset
request-status-countrequest-status-count <NUMBER>
Description: Set the maximum count of HTTP requests to track.
Syntax:
Set the maximum count of HTTP requests to track.. Number rangefrom=0 to=1024
<count>
Command Mode: http : HTTP communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# request-status-count <NUMBER>
request-status-count <NUMBER>
Description: Set the maximum count of HTTPS requests to track
Syntax:
Set the maximum count of HTTPS requests to track.. Number rangefrom=0 to=1024
<count>
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# request-status-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1092
R Commandsrequest-status-count
reset-to-factoryreset-to-factory
Description: Reset role to factory default privileges
Command Mode: rbac role : Create AAA role, attributes and privileges for user authorization
Command Path:
# configure [['terminal', 't']](config)# rbac role <WORD>(config-role)# reset-to-factory
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1093
R Commandsreset-to-factory
response-inclresponse-incl <respincl>
Description: Configure response subtree which needs to be included
Syntax:
The response subtree to be included<respincl>
Command Mode: query : Configure Query profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile(config-callhome-queryprof)# query <WORD> type dn|class <dn/classname>(config-callhome-queryprof-query)# response-incl <respincl>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1094
R Commandsresponse-incl
response-subtreeresponse-subtree full|children|no
Description: Configure response-subtree
Syntax:
Fullfull
Childrenchildren
Nono
Command Mode: query : Configure Query profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile(config-callhome-queryprof)# query <WORD> type dn|class <dn/classname>(config-callhome-queryprof-query)# response-subtree full|children|no
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1095
R Commandsresponse-subtree
retransmit-intervalretransmit-interval <NUMBER>
Description: Set the interval between LSA retransmissions
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# retransmit-interval <NUMBER>
retransmit-interval <NUMBER>
Description: Set the interval between LSA retransmissions
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# retransmit-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1096
R Commandsretransmit-interval
retriesretries <NUMBER>
Description: LDAP server retries for authentication
Syntax:
LDAP server retries for authentication. Number range from=0 to=5<0-5>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# retries <NUMBER>
retries <0-5>
Description: RADIUS server retries for authentication
Syntax:
RADIUS server retries for authentication<0-5>
Command Mode: radius-server host : RADIUS server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# retries <0-5>
retries <NUMBER>
Description: TACACS server retries for authentication
Syntax:
TACACS server retries for authentication. Number range from=0 to=5<0-5>
Command Mode: tacacs-server host : TACACS+ server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# retries <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1097
R Commandsretries
reverse-portreverse-port
Description: Decide if the ports should be reverted on filters of type both
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# reverse-port
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1098
R Commandsreverse-port
revisionrevision <NUMBER>
Description: Set the MST region revision number
Syntax:
MST region revision number. Number range from=0 to=65535<0-65535>
Command Mode: region : STP MST region configuration mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>(config-stp-region)# revision <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1099
R Commandsrevision
rolerole <WORD>
Description: Create the AAA domain role to set privilege bitmask of a user domain
Syntax:
User roleWORD
Command Mode: domain : Create the AAA domain to which the user belongs.
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# domain <WORD>(config-domain)# role <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1100
R Commandsrole
route-controlroute-control import|export
Description: Configure Route Control
Syntax:
Import Controlimport
Export Controlexport
Command Mode: l3out : Configuration for L3Out
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l3out <WORD>(config-tenant-l3out)# route-control import|export
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1101
R Commandsroute-control
route-maproute-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry>
Description: Configure route-map
Syntax:
Route-map nameWORD
denydeny
permitpermit
Sequence to insert to/delete from existing route-map entry. Numberrange from=0 to=65535
Sequence to insert to/delete fromexisting route-map entry
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existingroute-map entry>
route-map <WORD>
Description: Create route-map or enter route-map command mode
Syntax:
Route-map name (Max Size 64)WORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>
route-map <WORD> in|out
Description: Apply route-map to neighbor
Syntax:
Route Map Name (Max Size 63)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1102
R Commandsroute-map
Apply policy to incoming routesin
Apply policy to outgoing routesout
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# route-map <WORD> in|out
route-map <WORD>
Description: Create route-map or enter route-map command mode
Syntax:
Route-map name (Max Size 64)WORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>
route-map <WORD> in|out
Description: Apply route-map to neighbor
Syntax:
Route Map Name (Max Size 63)WORD
Apply policy to incoming routesin
Apply policy to outgoing routesout
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1103
R Commandsroute-map
(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# route-map <WORD> in|out
route-map interpod-import
Description: Import subnet from IPN
Syntax:
Import subnet from IPNinterpod-import
Command Mode: fabric-external : Intrasite/Intersite Connectivity Profile
Command Path:
# configure [['terminal', 't']](config)# fabric-external <NUMBER>(config-fabric-external)# route-map interpod-import
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1104
R Commandsroute-map
route-profileroute-profile <WORD>
Description: Configure route-profile
Syntax:
Route profile nameWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>
route-profile <WORD>
Description: Configure route-profile for bridge-domain
Syntax:
Route profile nameWORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# route-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1105
R Commandsroute-profile
route-reflectorroute-reflector spine <LIST> [description <TEXT>]
Description: Configure BGP route-reflectors
Syntax:
Configure Spines as route-reflectorsspine
Route-reflector spine node name or ID list. Ex. spine1 or 103,105LIST
(Optional) DescriptionTEXT
Command Mode: bgp-fabric : Border Gateway Protocol (BGP)
Command Path:
# configure [['terminal', 't']](config)# bgp-fabric(config-bgp-fabric)# route-reflector spine <LIST> [description <TEXT>]
route-reflector spine <LIST> [description <TEXT>]
Description: Configure BGP route-reflectors
Syntax:
Configure Spines as route-reflectorsspine
Route-reflector spine node name or ID list. Ex. spine1 or 103,105LIST
(Optional) DescriptionTEXT
Command Mode: bgp : Border Gateway Protocol (BGP)
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# bgp fabric(config-pod-bgp)# route-reflector spine <LIST> [description <TEXT>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1106
R Commandsroute-reflector
route-targetroute-target <WORD> <WORD>
Description: Route-Target
Syntax:
Route-Target modeWORD
Route-Target Extended Community in format<AS(4bytes)>:<NN(2bytes)> (Max Size None)
WORD
Command Mode: address-family : Address Family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# address-family ipv4|ipv6 unicast(config-leaf-vrf-af)# route-target <WORD> <WORD>
route-target <WORD> <WORD>
Description: Route-Target
Syntax:
Route-Target modeWORD
Route-Target Extended Community in format<AS(4bytes)>:<NN(2bytes)> (Max Size None)
WORD
Command Mode: address-family : Address Family
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# address-family ipv4|ipv6 unicast(config-leaf-vrf-af)# route-target <WORD> <WORD>
route-target extended <value>
Description: Global EVPN Route Target
Syntax:
Route-Target as extended communityextended
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1107
R Commandsroute-target
Community value in aa:nn formatvalue
Command Mode: fabric-external : Intrasite/Intersite Connectivity Profile
Command Path:
# configure [['terminal', 't']](config)# fabric-external <NUMBER>(config-fabric-external)# route-target extended <value>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1108
R Commandsroute-target
router-advertisement-guard-admin-statusrouter-advertisement-guard-admin-status enabled|disabled
Description: Config router advertisement administrative status in first hop security bridge domain policy
Syntax:
Enable router advertisement guardenabled
Disable router advertisement guarddisabled
Command Mode: security-policy : Configuration for security policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>(config-tenant-fhs-secpol)# router-advertisement-guard-admin-status enabled|disabled
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1109
R Commandsrouter-advertisement-guard-admin-status
router-advertisement-guardrouter-advertisement-guard
Description: Configuration for router advertisement guard policy
Command Mode: security-policy : Configuration for security policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>(config-tenant-fhs-secpol)# router-advertisement-guard
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1110
R Commandsrouter-advertisement-guard
router-advertisementrouter-advertisement
Description: Config trust router advertisement in trust control policy
Command Mode: trust-control : Configuration for trust control policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# trust-control <WORD>(config-tenant-fhs-trustctrl)# router-advertisement
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1111
R Commandsrouter-advertisement
router-idrouter-id <A.B.C.D|A:B::C:D>
Description: Set router-id for peer l4l7 device
Syntax:
IP address for the l4l7 peerA.B.C.D|A:B::C:D
Command Mode: rtr-cfg : Configure L4-L7 router configuration parameters
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# rtr-cfg <WORD>(rtr-cfg)# router-id <A.B.C.D|A:B::C:D>
router-id <A.B.C.D>
Description: Configure Router ID
Syntax:
Router ID ValueA.B.C.D
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# router-id <A.B.C.D>
router-id <A.B.C.D>
Description: Configure Router ID
Syntax:
Router ID ValueA.B.C.D
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1112
R Commandsrouter-id
(config-leaf-vrf)# router-id <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1113
R Commandsrouter-id
router bgprouter bgp <fabric-ASN>
Description: Border Gateway Protocol (BGP)
Syntax:
Autonomous System Number<fabric-ASN>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>
router bgp <fabric-ASN>
Description: Border Gateway Protocol (BGP)
Syntax:
Autonomous System Number<fabric-ASN>
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1114
R Commandsrouter bgp
router eigrprouter eigrp default
Description: Enhanced Interior Gateway Routing Protocol (EIGRP)
Syntax:
EIGRP process tagdefault
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default
router eigrp default
Description: Enhanced Interior Gateway Routing Protocol (EIGRP)
Syntax:
EIGRP process tagdefault
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1115
R Commandsrouter eigrp
router ospfrouter ospf default
Description: Open Shortest Path First (OSPF and OSPF Version3)
Syntax:
Process tag for ospf and ospfv3default
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default
router ospf default
Description: Open Shortest Path First (OSPF and OSPF Version3)
Syntax:
Process tag for ospf and ospfv3default
Command Mode: spine : Configure Spine Node
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1116
R Commandsrouter ospf
rtr-cfgrtr-cfg <WORD>
Description: Configure router configuration association for a L4-L7 service.
Syntax:
router configuration name (Max Size 64)WORD
Command Mode: service : Configure L4-L7 Service
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>] [svcredir <Service Redirection>] [service-type <Service Type>](config-service)# rtr-cfg <WORD>
rtr-cfg <WORD>
Description: Configure L4-L7 router configuration parameters
Syntax:
router configuration name (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# rtr-cfg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1117
R Commandsrtr-cfg
run-moderun-mode pause-never|pause-on-failure
Description: Set run-mode
Syntax:
Do not pause on failurepause-never
Pause upgrade if upgrade of current set of nodes failpause-on-failure
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# run-mode pause-never|pause-on-failure
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1118
R Commandsrun-mode
S Commands
• sampling-rate, page 1146
• scale-profile, page 1147
• schedule, page 1148
• scheduler, page 1149
• scheduling, page 1150
• scope, page 1151
• scvmm, page 1153
• second-file, page 1154
• security-domain, page 1155
• security-policy, page 1156
• security, page 1157
• security allow-promiscuous, page 1158
• security forged-transmits, page 1159
• security mac-changes, page 1160
• send-community, page 1161
• server, page 1162
• service-policy, page 1165
• service-policy type data-plane, page 1170
• service-policy type qos, page 1171
• service, page 1172
• session-record-flags, page 1173
• set, page 1174
• set addcommunity, page 1177
• set as-path prepend-last-as, page 1182
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1119
• set as-path prepend, page 1186
• set burst, page 1190
• set cir, page 1191
• set community, page 1192
• set conform-cos-transmit, page 1199
• set conform-dscp-transmit, page 1200
• set conform, page 1201
• set dampening, page 1202
• set dscp-code, page 1207
• set dscp, page 1208
• set exceed-cos-transmit, page 1209
• set exceed-dscp-transmit, page 1210
• set exceed, page 1211
• set excessive-burst, page 1212
• set local-preference, page 1213
• set metric-type, page 1217
• set metric, page 1221
• set mode, page 1225
• set next-hop, page 1226
• set pir, page 1230
• set qos-class, page 1231
• set tag, page 1233
• set target-dscp, page 1237
• set type, page 1238
• set violate-cos-transmit, page 1239
• set violate-dscp-transmit, page 1240
• set violate, page 1241
• set weight, page 1242
• shellinabox, page 1246
• show aaa authentication, page 1247
• show aaa groups, page 1248
• show access-list, page 1249
• show accounting log, page 1250
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1120
S Commands
• show acllog deny l2 flow, page 1251
• show acllog deny l2 flow tenant vrf, page 1252
• show acllog deny l2 flow tenant vrf detail, page 1253
• show acllog deny l2 pkt, page 1254
• show acllog deny l2 pkt tenant vrf, page 1255
• show acllog deny l2 pkt tenant vrf detail, page 1256
• show acllog deny l3 flow, page 1257
• show acllog deny l3 flow tenant vrf, page 1258
• show acllog deny l3 flow tenant vrf detail, page 1259
• show acllog deny l3 pkt, page 1260
• show acllog deny l3 pkt tenant vrf, page 1261
• show acllog deny l3 pkt tenant vrf detail, page 1262
• show acllog permit l2 flow tenant vrf, page 1264
• show acllog permit l2 flow tenant vrf detail, page 1265
• show acllog permit l2 pkt tenant vrf, page 1266
• show acllog permit l2 pkt tenant vrf detail, page 1267
• show acllog permit l3 flow tenant vrf, page 1268
• show acllog permit l3 flow tenant vrf detail, page 1269
• show acllog permit l3 pkt tenant vrf, page 1270
• show acllog permit l3 pkt tenant vrf detail, page 1271
• show analytics, page 1273
• show application, page 1274
• show audits, page 1275
• show audits tenant, page 1276
• show audits tenant application, page 1277
• show audits tenant application epg, page 1278
• show audits tenant bridge-domain, page 1279
• show audits tenant bridge-domain detail, page 1280
• show audits tenant bridge-domain first-hop-security binding-table, page 1281
• show audits tenant bridge-domain first-hop-security statistics arp, page 1282
• show audits tenant bridge-domain first-hop-security statistics dhcpv4, page 1283
• show audits tenant bridge-domain first-hop-security statistics dhcpv6, page 1284
• show audits tenant bridge-domain first-hop-security statistics neighbor-discovery, page 1285
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1121
S Commands
• show audits tenant dnsservergroup, page 1286
• show audits tenant dnsservergroup server, page 1287
• show audits tenant dnsservergroup server domain, page 1288
• show audits tenant interface bridge-domain, page 1289
• show audits tenant interface bridge-domain detail, page 1290
• show audits tenant interface bridge-domain first-hop-security binding-table, page 1291
• show audits tenant interface bridge-domain first-hop-security statistics arp, page 1292
• show audits tenant interface bridge-domain first-hop-security statistics dhcpv4, page 1293
• show audits tenant interface bridge-domain first-hop-security statistics dhcpv6, page 1294
• show audits tenant interface bridge-domain first-hop-security statistics neighbor-discovery, page 1295
• show audits tenant multicast-route-maps, page 1296
• show audits tenant vrf, page 1297
• show audits tenant vrf acllog l2, page 1298
• show audits tenant vrf acllog l3, page 1299
• show audits tenant vrf detail, page 1301
• show audits tenant vrf external-l3 bgp, page 1302
• show audits tenant vrf external-l3 bgp node, page 1303
• show audits tenant vrf external-l3 eigrp, page 1304
• show audits tenant vrf external-l3 eigrp detail, page 1305
• show audits tenant vrf external-l3 epg, page 1306
• show audits tenant vrf external-l3 epg detail, page 1307
• show audits tenant vrf external-l3 epg name, page 1308
• show audits tenant vrf external-l3 epg name detail, page 1309
• show audits tenant vrf external-l3 interfaces, page 1310
• show audits tenant vrf external-l3 interfaces detail, page 1311
• show audits tenant vrf external-l3 ospf, page 1312
• show audits tenant vrf external-l3 ospf detail, page 1313
• show audits tenant vrf external-l3 static-route, page 1314
• show audits tenant vrf external-l3 static-route detail, page 1315
• show audits tenant vrf external-l3 static-route node, page 1316
• show audits tenant vrf external-l3 static-route node detail, page 1317
• show audits tenant vrf multicast, page 1318
• show bridge-domain, page 1319
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1122
S Commands
• show bridge-domain detail, page 1320
• show bridge-domain first-hop-security binding-table, page 1321
• show bridge-domain first-hop-security statistics arp, page 1322
• show bridge-domain first-hop-security statistics dhcpv4, page 1323
• show bridge-domain first-hop-security statistics dhcpv6, page 1324
• show bridge-domain first-hop-security statistics neighbor-discovery, page 1325
• show callhome, page 1326
• show callhome common destination-profile, page 1327
• show callhome common query-profile, page 1328
• show callhome common transport-email, page 1329
• show catalog, page 1330
• show cli command, page 1331
• show cli internal audit, page 1332
• show cli internal transaction, page 1333
• show cli internal usage, page 1334
• show cli list, page 1335
• show cli manpage, page 1336
• show cli path, page 1337
• show clock, page 1338
• show communication ciphers, page 1339
• show communication controller, page 1340
• show communication http, page 1341
• show communication https, page 1342
• show communication shellinabox, page 1343
• show communication ssh-service, page 1344
• show communication telnet, page 1345
• show communication web-requests, page 1346
• show contract-type, page 1347
• show contract, page 1348
• show controller, page 1349
• show controller detail, page 1350
• show cores, page 1351
• show cores status, page 1352
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1123
S Commands
• show debug counter, page 1353
• show debug log, page 1354
• show deployment endpoint node, page 1355
• show dns-address, page 1356
• show dns-domain, page 1357
• show dot1q-tunnel, page 1358
• show endpoints, page 1359
• show endpoints leaf interface ethernet, page 1360
• show endpoints leaf interface port-channel, page 1361
• show endpoints vpc, page 1362
• show epg, page 1363
• show epg detail, page 1364
• show events, page 1365
• show events controller, page 1366
• show events controller detail, page 1367
• show events leaf, page 1368
• show events leaf fex, page 1369
• show events leaf fex module, page 1370
• show events leaf interface ethernet, page 1371
• show events leaf interface l3instance, page 1372
• show events leaf interface mgmt, page 1373
• show events leaf interface portchannel, page 1374
• show events leaf interface tunnel, page 1375
• show events leaf inventory chassis, page 1376
• show events leaf inventory fans, page 1377
• show events leaf inventory module, page 1378
• show events leaf inventory module fabricport, page 1379
• show events leaf inventory module leafport, page 1380
• show events leaf inventory powersupply, page 1381
• show events leaf inventory supervisor, page 1382
• show events leaf protocol, page 1383
• show events leaf vpc, page 1384
• show events leaf vrf, page 1385
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1124
S Commands
• show events spine, page 1386
• show events spine interface ethernet, page 1387
• show events spine interface l3instance, page 1388
• show events spine interface mgmt, page 1389
• show events spine interface tunnel, page 1390
• show events spine inventory chassis, page 1391
• show events spine inventory fabric, page 1392
• show events spine inventory fans, page 1393
• show events spine inventory module, page 1394
• show events spine inventory module fabricport, page 1395
• show events spine inventory powersupply, page 1396
• show events spine inventory supervisor, page 1397
• show events spine inventory system, page 1398
• show events spine protocol, page 1399
• show events spine vrf, page 1400
• show events tenant, page 1401
• show events tenant application, page 1402
• show events tenant application epg, page 1403
• show events tenant bridge-domain, page 1404
• show events tenant bridge-domain detail, page 1405
• show events tenant bridge-domain first-hop-security binding-table, page 1406
• show events tenant bridge-domain first-hop-security statistics arp, page 1407
• show events tenant bridge-domain first-hop-security statistics dhcpv4, page 1408
• show events tenant bridge-domain first-hop-security statistics dhcpv6, page 1409
• show events tenant bridge-domain first-hop-security statistics neighbor-discovery, page 1410
• show events tenant dnsservergroup, page 1411
• show events tenant dnsservergroup server, page 1412
• show events tenant dnsservergroup server domain, page 1413
• show events tenant endpoints, page 1414
• show events tenant endpoints leaf interface ethernet, page 1415
• show events tenant endpoints leaf interface port-channel, page 1416
• show events tenant endpoints vpc, page 1417
• show events tenant interface bridge-domain, page 1419
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1125
S Commands
• show events tenant interface bridge-domain detail, page 1420
• show events tenant interface bridge-domain first-hop-security binding-table, page 1421
• show events tenant interface bridge-domain first-hop-security statistics arp, page 1422
• show events tenant interface bridge-domain first-hop-security statistics dhcpv4, page 1423
• show events tenant interface bridge-domain first-hop-security statistics dhcpv6, page 1424
• show events tenant interface bridge-domain first-hop-security statistics neighbor-discovery, page 1425
• show events tenant multicast-route-maps, page 1426
• show events tenant vrf, page 1427
• show events tenant vrf acllog l2, page 1428
• show events tenant vrf acllog l3, page 1429
• show events tenant vrf detail, page 1431
• show events tenant vrf external-l3 bgp, page 1432
• show events tenant vrf external-l3 bgp node, page 1433
• show events tenant vrf external-l3 eigrp, page 1434
• show events tenant vrf external-l3 eigrp detail, page 1435
• show events tenant vrf external-l3 epg, page 1436
• show events tenant vrf external-l3 epg detail, page 1437
• show events tenant vrf external-l3 epg name, page 1438
• show events tenant vrf external-l3 epg name detail, page 1439
• show events tenant vrf external-l3 interfaces, page 1440
• show events tenant vrf external-l3 interfaces detail, page 1441
• show events tenant vrf external-l3 ospf, page 1442
• show events tenant vrf external-l3 ospf detail, page 1443
• show events tenant vrf external-l3 route-map, page 1444
• show events tenant vrf external-l3 route-map detail, page 1445
• show events tenant vrf external-l3 static-route, page 1446
• show events tenant vrf external-l3 static-route detail, page 1447
• show events tenant vrf external-l3 static-route node, page 1448
• show events tenant vrf external-l3 static-route node detail, page 1449
• show events tenant vrf multicast, page 1450
• show external-l2 epg, page 1451
• show external-l2 epg name, page 1452
• show external-l2 epg tenant, page 1453
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1126
S Commands
• show external-l3 bgp, page 1454
• show external-l3 bgp tenant, page 1455
• show external-l3 bgp tenant vrf, page 1456
• show external-l3 bgp tenant vrf node, page 1457
• show external-l3 eigrp, page 1458
• show external-l3 eigrp detail, page 1459
• show external-l3 eigrp node, page 1460
• show external-l3 eigrp node detail, page 1461
• show external-l3 eigrp tenant, page 1462
• show external-l3 eigrp tenant detail, page 1463
• show external-l3 eigrp tenant vrf, page 1464
• show external-l3 eigrp tenant vrf detail, page 1465
• show external-l3 eigrp tenant vrf node, page 1466
• show external-l3 eigrp tenant vrf node detail, page 1467
• show external-l3 epg, page 1468
• show external-l3 epg detail, page 1469
• show external-l3 epg name, page 1470
• show external-l3 epg name detail, page 1471
• show external-l3 epg tenant, page 1472
• show external-l3 epg tenant detail, page 1473
• show external-l3 epg tenant vrf, page 1474
• show external-l3 epg tenant vrf detail, page 1475
• show external-l3 interfaces, page 1476
• show external-l3 interfaces detail, page 1477
• show external-l3 interfaces node, page 1478
• show external-l3 interfaces node detail, page 1479
• show external-l3 interfaces tenant, page 1480
• show external-l3 interfaces tenant detail, page 1481
• show external-l3 interfaces tenant vrf, page 1482
• show external-l3 interfaces tenant vrf detail, page 1483
• show external-l3 interfaces tenant vrf node, page 1484
• show external-l3 interfaces tenant vrf node detail, page 1485
• show external-l3 ospf, page 1486
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1127
S Commands
• show external-l3 ospf detail, page 1487
• show external-l3 ospf node, page 1488
• show external-l3 ospf node detail, page 1489
• show external-l3 ospf tenant, page 1490
• show external-l3 ospf tenant detail, page 1491
• show external-l3 ospf tenant vrf, page 1492
• show external-l3 ospf tenant vrf detail, page 1493
• show external-l3 ospf tenant vrf node, page 1494
• show external-l3 ospf tenant vrf node detail, page 1495
• show external-l3 route-map, page 1496
• show external-l3 route-map detail, page 1497
• show external-l3 route-map name, page 1498
• show external-l3 route-map name detail, page 1499
• show external-l3 route-map tenant, page 1500
• show external-l3 route-map tenant detail, page 1501
• show external-l3 route-map tenant vrf, page 1502
• show external-l3 route-map tenant vrf detail, page 1503
• show external-l3 route-map tenant vrf node, page 1504
• show external-l3 route-map tenant vrf node detail, page 1505
• show external-l3 static-route, page 1506
• show external-l3 static-route detail, page 1507
• show external-l3 static-route node, page 1508
• show external-l3 static-route node detail, page 1509
• show external-l3 static-route tenant, page 1510
• show external-l3 static-route tenant detail, page 1511
• show external-l3 static-route tenant vrf, page 1512
• show external-l3 static-route tenant vrf detail, page 1513
• show external-l3 static-route tenant vrf node, page 1514
• show external-l3 static-route tenant vrf node detail, page 1515
• show fabric-recovery status, page 1516
• show faults, page 1517
• show faults controller, page 1519
• show faults controller detail, page 1520
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1128
S Commands
• show faults l4l7-cluster, page 1521
• show faults l4l7-graph, page 1522
• show faults leaf, page 1523
• show faults leaf fex, page 1524
• show faults leaf fex module, page 1525
• show faults leaf interface ethernet, page 1526
• show faults leaf interface l3instance, page 1527
• show faults leaf interface mgmt, page 1528
• show faults leaf interface portchannel, page 1529
• show faults leaf interface tunnel, page 1530
• show faults leaf inventory chassis, page 1531
• show faults leaf inventory fans, page 1532
• show faults leaf inventory module, page 1533
• show faults leaf inventory module fabricport, page 1534
• show faults leaf inventory module leafport, page 1535
• show faults leaf inventory powersupply, page 1536
• show faults leaf inventory supervisor, page 1537
• show faults leaf protocol, page 1538
• show faults leaf vpc, page 1539
• show faults leaf vrf, page 1540
• show faults microsoft domain, page 1541
• show faults microsoft domain name, page 1542
• show faults microsoft domain name hyperv, page 1543
• show faults microsoft domain name port-group, page 1544
• show faults microsoft domain name scvmm, page 1545
• show faults microsoft domain name vm, page 1546
• show faults microsoft domain name vm name, page 1547
• show faults quota, page 1548
• show faults spine, page 1549
• show faults spine interface ethernet, page 1550
• show faults spine interface l3instance, page 1551
• show faults spine interface mgmt, page 1552
• show faults spine interface tunnel, page 1553
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1129
S Commands
• show faults spine inventory chassis, page 1554
• show faults spine inventory fabric, page 1555
• show faults spine inventory fans, page 1556
• show faults spine inventory module, page 1557
• show faults spine inventory module fabricport, page 1558
• show faults spine inventory powersupply, page 1559
• show faults spine inventory supervisor, page 1560
• show faults spine inventory system, page 1561
• show faults spine protocol, page 1562
• show faults spine vrf, page 1563
• show faults tenant, page 1564
• show faults tenant application, page 1565
• show faults tenant application epg, page 1566
• show faults tenant bridge-domain, page 1567
• show faults tenant bridge-domain detail, page 1568
• show faults tenant bridge-domain first-hop-security binding-table, page 1569
• show faults tenant bridge-domain first-hop-security statistics arp, page 1570
• show faults tenant bridge-domain first-hop-security statistics dhcpv4, page 1571
• show faults tenant bridge-domain first-hop-security statistics dhcpv6, page 1572
• show faults tenant bridge-domain first-hop-security statistics neighbor-discovery, page 1573
• show faults tenant dnsservergroup, page 1574
• show faults tenant dnsservergroup server, page 1575
• show faults tenant dnsservergroup server domain, page 1576
• show faults tenant interface bridge-domain, page 1577
• show faults tenant interface bridge-domain detail, page 1578
• show faults tenant interface bridge-domain first-hop-security binding-table, page 1579
• show faults tenant interface bridge-domain first-hop-security statistics arp, page 1580
• show faults tenant interface bridge-domain first-hop-security statistics dhcpv4, page 1581
• show faults tenant interface bridge-domain first-hop-security statistics dhcpv6, page 1582
• show faults tenant interface bridge-domain first-hop-security statistics neighbor-discovery, page 1583
• show faults tenant multicast-route-maps, page 1584
• show faults tenant vrf, page 1585
• show faults tenant vrf acllog l2, page 1586
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1130
S Commands
• show faults tenant vrf acllog l3, page 1587
• show faults tenant vrf detail, page 1589
• show faults tenant vrf external-l3 bgp, page 1590
• show faults tenant vrf external-l3 bgp node, page 1591
• show faults tenant vrf external-l3 eigrp, page 1592
• show faults tenant vrf external-l3 eigrp detail, page 1593
• show faults tenant vrf external-l3 epg, page 1594
• show faults tenant vrf external-l3 epg detail, page 1595
• show faults tenant vrf external-l3 epg name, page 1596
• show faults tenant vrf external-l3 epg name detail, page 1597
• show faults tenant vrf external-l3 interfaces, page 1598
• show faults tenant vrf external-l3 interfaces detail, page 1599
• show faults tenant vrf external-l3 ospf, page 1600
• show faults tenant vrf external-l3 ospf detail, page 1601
• show faults tenant vrf external-l3 static-route, page 1602
• show faults tenant vrf external-l3 static-route detail, page 1603
• show faults tenant vrf external-l3 static-route node, page 1604
• show faults tenant vrf external-l3 static-route node detail, page 1605
• show faults tenant vrf multicast, page 1606
• show faults vmware domain, page 1607
• show faults vmware domain name, page 1608
• show faults vmware domain name epg, page 1609
• show faults vmware domain name esx, page 1610
• show faults vmware domain name port-group, page 1611
• show faults vmware domain name trunk-portgroup, page 1612
• show faults vmware domain name vcenter, page 1613
• show faults vmware domain name vm, page 1614
• show faults vmware domain name vm name, page 1615
• show fips, page 1616
• show fips status, page 1617
• show firmware repository, page 1618
• show firmware repository detail, page 1619
• show firmware upgrade status, page 1620
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1131
S Commands
• show firmware upgrade status controller-group, page 1621
• show firmware upgrade status controller-group detail, page 1622
• show firmware upgrade status detail, page 1623
• show firmware upgrade status switch-group, page 1624
• show firmware upgrade status switch-group detail, page 1625
• show flow exporter, page 1626
• show flow exporter infra, page 1627
• show flow exporter tenant, page 1628
• show flow monitor, page 1629
• show flow monitor infra, page 1630
• show flow monitor tenant, page 1631
• show flow node-policy, page 1632
• show flow node-policy detail, page 1633
• show flow record, page 1634
• show flow record infra, page 1635
• show flow record tenant, page 1636
• show flow vm-exporter, page 1637
• show health, page 1638
• show health leaf, page 1639
• show health leaf fex, page 1640
• show health leaf fex module, page 1641
• show health leaf interface ethernet, page 1642
• show health leaf interface l3instance, page 1643
• show health leaf interface mgmt, page 1644
• show health leaf interface portchannel, page 1645
• show health leaf interface tunnel, page 1646
• show health leaf inventory chassis, page 1647
• show health leaf inventory fans, page 1648
• show health leaf inventory module, page 1649
• show health leaf inventory module fabricport, page 1650
• show health leaf inventory module leafport, page 1651
• show health leaf inventory powersupply, page 1652
• show health leaf inventory supervisor, page 1653
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1132
S Commands
• show health leaf protocol, page 1654
• show health leaf vpc, page 1655
• show health leaf vrf, page 1656
• show health spine, page 1657
• show health spine interface ethernet, page 1658
• show health spine interface l3instance, page 1659
• show health spine interface mgmt, page 1660
• show health spine interface tunnel, page 1661
• show health spine inventory chassis, page 1662
• show health spine inventory fabric, page 1663
• show health spine inventory fans, page 1664
• show health spine inventory module, page 1665
• show health spine inventory module fabricport, page 1666
• show health spine inventory powersupply, page 1667
• show health spine inventory supervisor, page 1668
• show health spine inventory system, page 1669
• show health spine protocol, page 1670
• show health spine vrf, page 1671
• show health tenant, page 1672
• show health tenant application, page 1673
• show health tenant application epg, page 1674
• show health tenant bridge-domain, page 1675
• show health tenant bridge-domain detail, page 1676
• show health tenant bridge-domain first-hop-security binding-table, page 1677
• show health tenant bridge-domain first-hop-security statistics arp, page 1678
• show health tenant bridge-domain first-hop-security statistics dhcpv4, page 1679
• show health tenant bridge-domain first-hop-security statistics dhcpv6, page 1680
• show health tenant bridge-domain first-hop-security statistics neighbor-discovery, page 1681
• show health tenant dnsservergroup, page 1682
• show health tenant dnsservergroup server, page 1683
• show health tenant dnsservergroup server domain, page 1684
• show health tenant interface bridge-domain, page 1685
• show health tenant interface bridge-domain detail, page 1686
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1133
S Commands
• show health tenant interface bridge-domain first-hop-security binding-table, page 1687
• show health tenant interface bridge-domain first-hop-security statistics arp, page 1688
• show health tenant interface bridge-domain first-hop-security statistics dhcpv4, page 1689
• show health tenant interface bridge-domain first-hop-security statistics dhcpv6, page 1690
• show health tenant interface bridge-domain first-hop-security statistics neighbor-discovery, page 1691
• show health tenant multicast-route-maps, page 1692
• show health tenant vrf, page 1693
• show health tenant vrf acllog l2, page 1694
• show health tenant vrf acllog l3, page 1695
• show health tenant vrf detail, page 1697
• show health tenant vrf external-l3 bgp, page 1698
• show health tenant vrf external-l3 bgp node, page 1699
• show health tenant vrf external-l3 eigrp, page 1700
• show health tenant vrf external-l3 eigrp detail, page 1701
• show health tenant vrf external-l3 epg, page 1702
• show health tenant vrf external-l3 epg detail, page 1703
• show health tenant vrf external-l3 epg name, page 1704
• show health tenant vrf external-l3 epg name detail, page 1705
• show health tenant vrf external-l3 interfaces, page 1706
• show health tenant vrf external-l3 interfaces detail, page 1707
• show health tenant vrf external-l3 ospf, page 1708
• show health tenant vrf external-l3 ospf detail, page 1709
• show health tenant vrf external-l3 static-route, page 1710
• show health tenant vrf external-l3 static-route detail, page 1711
• show health tenant vrf external-l3 static-route node, page 1712
• show health tenant vrf external-l3 static-route node detail, page 1713
• show health tenant vrf multicast, page 1714
• show inband-mgmt, page 1715
• show inband-mgmt controller, page 1716
• show inband-mgmt switch, page 1717
• show interface bridge-domain, page 1718
• show interface bridge-domain detail, page 1719
• show interface bridge-domain first-hop-security binding-table, page 1720
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1134
S Commands
• show interface bridge-domain first-hop-security statistics arp, page 1721
• show interface bridge-domain first-hop-security statistics dhcpv4, page 1722
• show interface bridge-domain first-hop-security statistics dhcpv6, page 1723
• show interface bridge-domain first-hop-security statistics neighbor-discovery, page 1724
• show ip interface bridge-domain, page 1725
• show ipv6 interface bridge-domain, page 1726
• show l4l7-cluster, page 1727
• show l4l7-graph, page 1728
• show l4l7-package, page 1729
• show ldap-server, page 1730
• show locator-led, page 1731
• show locator-led status leaf, page 1732
• show microsoft domain, page 1733
• show microsoft domain name, page 1734
• show microsoft domain name hyperv, page 1735
• show microsoft domain name port-group, page 1736
• show microsoft domain name scvmm, page 1737
• show microsoft domain name vm, page 1738
• show microsoft domain name vm name, page 1739
• show microsoft vm, page 1740
• show monitor access, page 1741
• show monitor fabric, page 1742
• show monitor summary, page 1743
• show monitor tenant, page 1744
• show monitor virtual, page 1745
• show name-alias tenant, page 1746
• show name-alias tenant acl, page 1747
• show name-alias tenant application, page 1748
• show name-alias tenant application epg, page 1749
• show name-alias tenant bridge-domain, page 1750
• show name-alias tenant contract, page 1751
• show name-alias tenant contract subject, page 1752
• show name-alias tenant l3out, page 1753
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1135
S Commands
• show name-alias tenant vrf, page 1754
• show ntpq, page 1755
• show oob-mgmt, page 1756
• show oob-mgmt controller, page 1757
• show oob-mgmt switch, page 1758
• show pd-recovery status, page 1759
• show policy-map, page 1760
• show policy-map type data-plane, page 1761
• show policy-map type qos, page 1762
• show port-channel leaf, page 1763
• show port-channel map, page 1764
• show port-channel map leaf, page 1765
• show pwd-rules, page 1766
• show quota, page 1767
• show radius-server, page 1768
• show resource, page 1769
• show resource conflict encap-vlan epg, page 1770
• show resource conflict encap-vlan epg node, page 1771
• show role, page 1772
• show running-config, page 1773
• show sessions, page 1774
• show sessions controller, page 1775
• show sessions controller detail, page 1776
• show sessions leaf, page 1777
• show sessions spine, page 1778
• show snapshot active, page 1779
• show snapshot files, page 1780
• show snapshot jobs, page 1781
• show snmp, page 1782
• show snmp clientgroups, page 1783
• show snmp community, page 1784
• show snmp engineid, page 1785
• show snmp hosts, page 1786
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1136
S Commands
• show snmp summary, page 1787
• show snmp users, page 1788
• show stats, page 1789
• show stats granularity communication controller, page 1790
• show stats granularity leaf, page 1791
• show stats granularity leaf fex, page 1792
• show stats granularity leaf fex module, page 1793
• show stats granularity leaf interface ethernet, page 1794
• show stats granularity leaf interface mgmt, page 1795
• show stats granularity leaf interface portchannel, page 1796
• show stats granularity leaf inventory chassis, page 1797
• show stats granularity leaf inventory fans, page 1798
• show stats granularity leaf inventory powersupply, page 1799
• show stats granularity leaf inventory supervisor, page 1800
• show stats granularity spine, page 1801
• show stats granularity spine interface ethernet, page 1802
• show stats granularity spine interface mgmt, page 1803
• show stats granularity spine inventory chassis, page 1804
• show stats granularity spine inventory fabric, page 1805
• show stats granularity spine inventory fans, page 1806
• show stats granularity spine inventory module, page 1807
• show stats granularity spine inventory powersupply, page 1808
• show stats granularity spine inventory supervisor, page 1809
• show stats granularity spine inventory system, page 1810
• show stats granularity tenant, page 1811
• show stats granularity tenant application, page 1812
• show stats granularity tenant application epg, page 1813
• show stats granularity tenant dnsservergroup, page 1814
• show stats granularity tenant dnsservergroup server, page 1815
• show stats granularity tenant dnsservergroup server domain, page 1816
• show stats granularity tenant dot1q-tunnel, page 1817
• show stats granularity tenant multicast-route-maps, page 1818
• show stats granularity tenant vrf, page 1819
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1137
S Commands
• show stats granularity tenant vrf acllog l2, page 1820
• show stats granularity tenant vrf acllog l3, page 1821
• show stats granularity tenant vrf detail, page 1822
• show stats granularity tenant vrf external-l3 bgp, page 1823
• show stats granularity tenant vrf external-l3 bgp node, page 1824
• show stats granularity tenant vrf external-l3 eigrp, page 1825
• show stats granularity tenant vrf external-l3 eigrp detail, page 1826
• show stats granularity tenant vrf external-l3 epg, page 1827
• show stats granularity tenant vrf external-l3 epg detail, page 1828
• show stats granularity tenant vrf external-l3 epg name, page 1829
• show stats granularity tenant vrf external-l3 epg name detail, page 1830
• show stats granularity tenant vrf external-l3 interfaces, page 1831
• show stats granularity tenant vrf external-l3 interfaces detail, page 1832
• show stats granularity tenant vrf external-l3 ospf, page 1833
• show stats granularity tenant vrf external-l3 ospf detail, page 1834
• show stats granularity tenant vrf external-l3 static-route, page 1835
• show stats granularity tenant vrf external-l3 static-route detail, page 1836
• show stats granularity tenant vrf external-l3 static-route node, page 1837
• show stats granularity tenant vrf external-l3 static-route node detail, page 1838
• show stats granularity tenant vrf multicast, page 1839
• show switch, page 1840
• show switch detail, page 1841
• show tacacs-server, page 1842
• show techsupport all, page 1843
• show techsupport controllers, page 1844
• show techsupport host, page 1845
• show techsupport switch, page 1846
• show tenant, page 1847
• show tenant access-list, page 1848
• show tenant application, page 1849
• show tenant application endpoints, page 1850
• show tenant application endpoints leaf interface ethernet, page 1851
• show tenant application endpoints leaf interface port-channel, page 1852
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1138
S Commands
• show tenant application endpoints vpc, page 1853
• show tenant application epg, page 1854
• show tenant application epg detail, page 1855
• show tenant application epg endpoints, page 1856
• show tenant application epg endpoints leaf interface ethernet, page 1857
• show tenant application epg endpoints leaf interface port-channel, page 1858
• show tenant application epg endpoints vpc, page 1859
• show tenant bridge-domain, page 1861
• show tenant bridge-domain detail, page 1862
• show tenant bridge-domain first-hop-security binding-table, page 1863
• show tenant bridge-domain first-hop-security statistics arp, page 1864
• show tenant bridge-domain first-hop-security statistics dhcpv4, page 1865
• show tenant bridge-domain first-hop-security statistics dhcpv6, page 1866
• show tenant bridge-domain first-hop-security statistics neighbor-discovery, page 1867
• show tenant contract-type, page 1868
• show tenant contract, page 1869
• show tenant detail, page 1870
• show tenant dnsservergroup, page 1871
• show tenant dnsservergroup server, page 1872
• show tenant dnsservergroup server domain, page 1873
• show tenant dot1q-tunnel, page 1874
• show tenant endpoints, page 1875
• show tenant endpoints leaf interface ethernet, page 1876
• show tenant endpoints leaf interface port-channel, page 1877
• show tenant endpoints vpc, page 1878
• show tenant epg, page 1879
• show tenant epg detail, page 1880
• show tenant external-l2 epg, page 1881
• show tenant interface bridge-domain, page 1882
• show tenant interface bridge-domain detail, page 1883
• show tenant interface bridge-domain first-hop-security binding-table, page 1884
• show tenant interface bridge-domain first-hop-security statistics arp, page 1885
• show tenant interface bridge-domain first-hop-security statistics dhcpv4, page 1886
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1139
S Commands
• show tenant interface bridge-domain first-hop-security statistics dhcpv6, page 1887
• show tenant interface bridge-domain first-hop-security statistics neighbor-discovery, page 1888
• show tenant ip interface bridge-domain, page 1889
• show tenant ipv6 interface bridge-domain, page 1890
• show tenant multicast-route-maps, page 1891
• show tenant policy-map, page 1892
• show tenant policy-map type data-plane, page 1893
• show tenant policy-map type qos, page 1894
• show tenant vrf, page 1895
• show tenant vrf acllog l2, page 1896
• show tenant vrf acllog l3, page 1897
• show tenant vrf detail, page 1898
• show tenant vrf external-l3 bgp, page 1899
• show tenant vrf external-l3 bgp node, page 1900
• show tenant vrf external-l3 eigrp, page 1901
• show tenant vrf external-l3 eigrp detail, page 1902
• show tenant vrf external-l3 epg, page 1903
• show tenant vrf external-l3 epg detail, page 1904
• show tenant vrf external-l3 epg name, page 1905
• show tenant vrf external-l3 epg name detail, page 1906
• show tenant vrf external-l3 interfaces, page 1907
• show tenant vrf external-l3 interfaces detail, page 1908
• show tenant vrf external-l3 ospf, page 1909
• show tenant vrf external-l3 ospf detail, page 1910
• show tenant vrf external-l3 route-map, page 1911
• show tenant vrf external-l3 route-map detail, page 1912
• show tenant vrf external-l3 static-route, page 1913
• show tenant vrf external-l3 static-route detail, page 1914
• show tenant vrf external-l3 static-route node, page 1915
• show tenant vrf external-l3 static-route node detail, page 1916
• show tenant vrf multicast, page 1917
• show troubleshoot epext session, page 1918
• show troubleshoot epext session atomiccounter, page 1919
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1140
S Commands
• show troubleshoot epext session audit, page 1920
• show troubleshoot epext session contracts, page 1921
• show troubleshoot epext session deployments, page 1922
• show troubleshoot epext session events, page 1923
• show troubleshoot epext session faults, page 1924
• show troubleshoot epext session latency, page 1925
• show troubleshoot epext session monitor, page 1926
• show troubleshoot epext session reports, page 1927
• show troubleshoot epext session statistics, page 1928
• show troubleshoot epext session topology, page 1929
• show troubleshoot epext session traceroute, page 1930
• show troubleshoot epext sessions, page 1931
• show troubleshoot eptoep session, page 1932
• show troubleshoot eptoep session atomiccounter, page 1933
• show troubleshoot eptoep session audit, page 1934
• show troubleshoot eptoep session contracts, page 1935
• show troubleshoot eptoep session deployments, page 1936
• show troubleshoot eptoep session events, page 1937
• show troubleshoot eptoep session faults, page 1938
• show troubleshoot eptoep session latency, page 1939
• show troubleshoot eptoep session monitor, page 1940
• show troubleshoot eptoep session reports, page 1941
• show troubleshoot eptoep session statistics, page 1942
• show troubleshoot eptoep session topology, page 1943
• show troubleshoot eptoep session traceroute, page 1944
• show troubleshoot eptoep sessions, page 1945
• show username, page 1946
• show username detail, page 1947
• show version, page 1948
• show vlan-domain, page 1949
• show vmm internal debug, page 1950
• show vmm internal debug epg, page 1951
• show vmm internal debug mac, page 1952
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1141
S Commands
• show vmware domain, page 1953
• show vmware domain name, page 1954
• show vmware domain name epg, page 1955
• show vmware domain name esx, page 1956
• show vmware domain name port-group, page 1957
• show vmware domain name trunk-portgroup, page 1958
• show vmware domain name vcenter, page 1959
• show vmware domain name vm, page 1960
• show vmware domain name vm name, page 1961
• show vmware vm, page 1962
• show vpc, page 1963
• show vpc map leaf, page 1964
• show vrf, page 1965
• show vrf detail, page 1966
• show vsan-domain, page 1967
• shut, page 1968
• shutdown, page 1969
• site-id, page 1973
• slow-drain congestion-timeout action, page 1974
• slow-drain congestion-timeout count, page 1977
• slow-drain pause, page 1980
• slow-timer, page 1983
• snapshot download, page 1984
• snapshot export, page 1985
• snapshot import, page 1986
• snapshot rollback, page 1987
• snapshot upload, page 1988
• snmp-server clientgroup, page 1989
• snmp-server community, page 1990
• snmp-server contact, page 1991
• snmp-server host, page 1992
• snmp-server location, page 1993
• snmp-server protocol, page 1994
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1142
S Commands
• snmp-server user, page 1995
• source-guard-admin-status, page 1996
• source, page 1997
• source application, page 1999
• source interface ethernet, page 2000
• source interface port-channel, page 2001
• source interface vpc, page 2002
• spanning-tree, page 2003
• spanning-tree bpdu-filter, page 2007
• spanning-tree bpdu-guard, page 2008
• speed, page 2009
• spf-interval, page 2012
• spine-group, page 2013
• spine-interface-group, page 2014
• spine-interface-policy-group, page 2015
• spine-interface-profile, page 2017
• spine-policy-group, page 2018
• spine-profile, page 2019
• spine, page 2020
• ssh-key, page 2021
• ssh-service, page 2022
• ssl-protocols, page 2023
• ssl-validation-level, page 2024
• state, page 2025
• static-endpoint, page 2026
• static-tep, page 2030
• statistics, page 2034
• storm-control broadcast level, page 2035
• storm-control broadcast pps, page 2038
• storm-control level, page 2041
• storm-control multicast level, page 2044
• storm-control multicast pps, page 2047
• storm-control pps, page 2050
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1143
S Commands
• storm-control unicast level, page 2053
• storm-control unicast pps, page 2056
• street-address, page 2059
• subject, page 2060
• subnet, page 2061
• summary-address, page 2062
• svcredir-pol, page 2063
• switch-group, page 2064
• switch, page 2065
• switching, page 2066
• switchport, page 2067
• switchport access vlan tenant application, page 2069
• switchport access vlan tenant external-svi, page 2073
• switchport mode, page 2076
• switchport port-authentication, page 2080
• switchport port-authentication enable, page 2081
• switchport port-authentication host-mode, page 2082
• switchport port-security maximum, page 2083
• switchport port-security timeout, page 2086
• switchport port-security violation, page 2089
• switchport tenant, page 2092
• switchport trunk allowed vlan inband-mgmt, page 2095
• switchport trunk allowed vlan tenant application, page 2096
• switchport trunk allowed vlan tenant external-l2, page 2100
• switchport trunk allowed vlan tenant external-svi, page 2103
• switchport trunk allowed vlan tenant legacy-forwarding, page 2106
• switchport trunk allowed vsan tenant application, page 2109
• switchport trunk native vlan tenant application, page 2112
• switchport trunk native vlan tenant external-svi, page 2116
• switchport trunk qinq outer-vlan inner-vlan tenant application, page 2119
• switchport vepa, page 2123
• switchport vlan, page 2126
• switchport vsan, page 2129
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1144
S Commands
• switchport vsan tenant application, page 2132
• syslog, page 2133
• system cluster-size, page 2134
• system controller-id, page 2135
• system dynamic-load-balance, page 2136
• system fabric-security-mode, page 2137
• system jumbomtu, page 2138
• system pod, page 2139
• system switch-id, page 2140
• system use-infra-gipo, page 2141
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1145
S Commands
sampling-ratesampling-rate <samplingRate>
Description: Configure Sampling Rate
Syntax:
Configure Sampling Rate. Number range from=0 to=1000samplingRate
Command Mode: flow exporter : Configure NetFlow Exporter Policy
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-dvs(config-vmware-dvs)# flow exporter <WORD>(config-vmware-dvs-flow-exporter)# sampling-rate <samplingRate>
sampling-rate <samplingRate>
Description: Configure Sampling Rate
Syntax:
Configure Sampling Rate. Number range from=0 to=1000samplingRate
Command Mode: flow exporter : Configure NetFlow Exporter Policy
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# flow exporter <WORD>(config-vmware-avs-flow-exporter)# sampling-rate <samplingRate>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1146
S Commandssampling-rate
scale-profilescale-profile <WORD>
Description: Configure Forwarding Scale Profile policy
Syntax:
Provide a Forwarding Scale Profile policy nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# scale-profile <WORD>
scale-profile <arg>
Description: Add Forwarding Scale Profile policy
Syntax:
arg
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# scale-profile <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1147
S Commandsscale-profile
scheduleschedule <WORD>
Description: Assign a scheduler
Syntax:
scheduler name (Max Size 64)WORD
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# schedule <WORD>
schedule <WORD>
Description: Schedule snapshot export
Syntax:
Scheduler nameWORD
Command Mode: snapshot export : Configuration export setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot export <WORD>(config-export)# schedule <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1148
S Commandsschedule
schedulerscheduler pause
Description: Pause maintenance policy scheduler
Syntax:
Pause maintenance policy schedulerpause
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# scheduler pause
scheduler fabric|controller schedule <WORD>
Description: Scheduler configuration mode
Syntax:
Fabric schedulesfabric
Controller schedulescontroller
Configure a scheduleschedule
Schedule name (Max size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1149
S Commandsscheduler
schedulingscheduling <WORD>
Description: Set the scheduling algorithm
Syntax:
Algorithm to chooseWORD
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# scheduling <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1150
S Commandsscheduling
scopescope <WORD>
Description: Specify the scope for the contract
Syntax:
Contract ScopeWORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# scope <WORD>
scope combinable
Description: Set route-profile scope
Syntax:
combinablecombinable
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# scope combinable
scope global
Description: Set scope
Syntax:
Route-map will be available for use on all nodes in this tenant and vrfglobal
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1151
S Commandsscope
(config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# scope global
scope combinable
Description: Set route-profile scope
Syntax:
combinablecombinable
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# scope combinable
scope global
Description: Set scope
Syntax:
Route-map will be available for use on all nodes in this tenant and vrfglobal
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# scope global
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1152
S Commandsscope
scvmmscvmm <arg> cloud <WORD> [name <name>]
Description: Configure an SCVMM in the Microsoft domain
Syntax:
arg
Cloud namecloud
Cloud Name (Max Size 512)WORD
(Optional) SCVMM Controller Namename
Command Mode: microsoft-domain : Create a VMMMicrosoft Domain
Command Path:
# configure [['terminal', 't']](config)# microsoft-domain <WORD> [delimiter <WORD>](config-microsoft)# scvmm <> cloud <WORD> [name <name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1153
S Commandsscvmm
second-filesecond-file <FILENAME>
Description: Second snapshot file name
Syntax:
Second snapshot file nameFILENAME
Command Mode: snapshot rollback : Configuration rollback setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot rollback <WORD>(config-rollback)# second-file <FILENAME>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1154
S Commandssecond-file
security-domainsecurity-domain <WORD>
Description: Add security domain
Syntax:
Security-domain nameWORD
Command Mode: vlan-domain : Configure vlan domain
Command Path:
# configure [['terminal', 't']](config)# vlan-domain <name> [dynamic] [type <domain-type>](config-vlan)# security-domain <WORD>
security-domain <WORD>
Description: Add a security domain to this VMware domain
Syntax:
Security domain name (Max Size 64)WORD
Command Mode: vmware-domain : Create a VMM VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# security-domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1155
S Commandssecurity-domain
security-policysecurity-policy <WORD>
Description: Configuration for security policy
Syntax:
security policy name (Max Size 64)WORD
Command Mode: first-hop-security : Configuration for first hop security
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1156
S Commandssecurity-policy
securitysecurity domain <WORD>
Description: Add a security domain to the tenant
Syntax:
Domaindomain
Security domain name (Max Size None)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# security domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1157
S Commandssecurity
security allow-promiscuoussecurity allow-promiscuous <WORD>
Description: Enable/Disable promiscuous mode
Syntax:
Enable/Disable promiscuous modeWORD
Command Mode: vmware-domain : Associate EPG to a VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>][allow-micro-segmentation] [deploy <WORD>] [push <WORD>] [delimiter <WORD>](config-tenant-app-epg-domain)# security allow-promiscuous <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1158
S Commandssecurity allow-promiscuous
security forged-transmitssecurity forged-transmits <WORD>
Description: Accept/Reject Forced Transmits
Syntax:
Accept/Reject Forged TransmitsWORD
Command Mode: vmware-domain : Associate EPG to a VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>][allow-micro-segmentation] [deploy <WORD>] [push <WORD>] [delimiter <WORD>](config-tenant-app-epg-domain)# security forged-transmits <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1159
S Commandssecurity forged-transmits
security mac-changessecurity mac-changes <WORD>
Description: Accept/Reject Mac Changes
Syntax:
Accept/Reject Mac ChangesWORD
Command Mode: vmware-domain : Associate EPG to a VMWare Domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>][allow-micro-segmentation] [deploy <WORD>] [push <WORD>] [delimiter <WORD>](config-tenant-app-epg-domain)# security mac-changes <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1160
S Commandssecurity mac-changes
send-communitysend-community [extended]
Description: Send Community attribute to this neighbor
Syntax:
(Optional) Send Extended Community attributeextended
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# send-community [extended]
send-community [extended]
Description: Send Community attribute to this neighbor
Syntax:
(Optional) Send Extended Community attributeextended
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router bgp <fabric-ASN>(config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out<WORD>](config-leaf-bgp-vrf-neighbor)# send-community [extended]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1161
S Commandssend-community
serverserver <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
Description: Add LDAP server to LDAP group
Syntax:
LDAP server name or IP addressA.B.C.D|A:B::C:D|WORD
priority of server within grouppriority
Priority of server within group. Number range from=0 to=16<0-16>
Command Mode: aaa group server ldap : LDAP server group name.
Command Path:
# configure [['terminal', 't']](config)# aaa group server ldap <WORD>(config-ldap)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
Description: Add RADIUS server to RADIUS group
Syntax:
RADIUS server name or IP addressA.B.C.D|A:B::C:D|WORD
priority of server within grouppriority
Priority of server within group. Number range from=0 to=16<0-16>
Command Mode: aaa group server radius : RADIUS server group name.
Command Path:
# configure [['terminal', 't']](config)# aaa group server radius <WORD>(config-radius)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
Description: Add TACACS PLUS server to TACACS PLUS group
Syntax:
TACACS PLUS server name or IP addressA.B.C.D|A:B::C:D|WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1162
S Commandsserver
priority of server within grouppriority
Priority of server within group. Number range from=0 to=16<0-16>
Command Mode: aaa group server tacacsplus : TACACS+ server group name.
Command Path:
# configure [['terminal', 't']](config)# aaa group server tacacsplus <WORD>(config-tacacsplus)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
server <WORD> [prefer] [key <arg>] [use-vrf <arg>]
Description: Configure ntp servers for the active ntp policy
Syntax:
Server name/IP for the active ntp policy (Max Size 64)WORD
(Optional) Preferred server for the active ntp policyprefer
(Optional) Reference key id for authentication. Number range from=1to=65535
arg
(Optional) Configure management vrfarg
Command Mode: ntp : Configure the default ntp policy
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# ntp(config-ntp)# server <WORD> [prefer] [key <>] [use-vrf <>]
server <WORD> [prefer] [key <arg>] [use-vrf <arg>]
Description: Configure ntp servers for the active ntp policy
Syntax:
Server name/IP for the active ntp policy (Max Size 64)WORD
(Optional) Preferred server for the active ntp policyprefer
(Optional) Reference key id for authentication. Number range from=1to=65535
arg
(Optional) Configure management vrfarg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1163
S Commandsserver
Command Mode: template ntp-fabric : Network Time Protocol (NTP)
Command Path:
# configure [['terminal', 't']](config)# template ntp-fabric <WORD>(config-template-ntp-fabric)# server <WORD> [prefer] [key <>] [use-vrf <>]
server <host/ipaddr> [facility <facility>] [severity <severity>] [mgmtepg <mgmtepg>] [port <port>] [format<format>]
Description: Add a destination server
Syntax:
The hostname or ipaddress<host/ipaddr>
(Optional) The forwarding facility level for logs generatedfacility
(Optional) The severity level for logs generatedseverity
(Optional) MgmtEndpointmgmtepg
(Optional) Service port of the remote destination. Number range from=1to=65535
port
(Optional) The format for the syslog messagesformat
Command Mode: logging : Logging server group configuration mode
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# server <host/ipaddr> [facility <facility>] [severity <severity>] [mgmtepg<mgmtepg>] [port <port>] [format <format>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1164
S Commandsserver
service-policyservice-policy type data-plane|control-plane-if <arg> <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
QOS policy for Control Plane Policingcontrol-plane-if
arg
Qos Policy Name (Max Size 64)WORD
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# service-policy type data-plane|control-plane-if <> <WORD>
service-policy <WORD>
Description: Specify the QOS service policy
Syntax:
Service policy to apply (Max Size 64)WORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# service-policy <WORD>
service-policy type data-plane input|output <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1165
S Commandsservice-policy
QOS policy for Data Plane Policingdata-plane
Ingress Directioninput
Egress Directionoutput
Qos Policy Name (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# service-policy type data-plane input|output <WORD>
service-policy type data-plane|control-plane-if <arg> <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
QOS policy for Control Plane Policingcontrol-plane-if
arg
Qos Policy Name (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# service-policy type data-plane|control-plane-if <> <WORD>
service-policy type data-plane|control-plane-if <arg> <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1166
S Commandsservice-policy
QOS policy for Control Plane Policingcontrol-plane-if
arg
Qos Policy Name (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# service-policy type data-plane|control-plane-if <> <WORD>
service-policy type data-plane input|output <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
Ingress Directioninput
Egress Directionoutput
Qos Policy Name (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vlan <1-4094>(config-leaf-if)# service-policy type data-plane input|output <WORD>
service-policy type data-plane|control-plane-if <arg> <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
QOS policy for Control Plane Policingcontrol-plane-if
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1167
S Commandsservice-policy
arg
Qos Policy Name (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# service-policy type data-plane|control-plane-if <> <WORD>
service-policy type data-plane|control-plane-if <arg> <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
QOS policy for Control Plane Policingcontrol-plane-if
arg
Qos Policy Name (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# service-policy type data-plane|control-plane-if <> <WORD>
service-policy type data-plane input|output <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
Ingress Directioninput
Egress Directionoutput
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1168
S Commandsservice-policy
Qos Policy Name (Max Size 64)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# service-policy type data-plane input|output <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1169
S Commandsservice-policy
service-policy type data-planeservice-policy type data-plane <WORD>
Description: Data plane Policy
Syntax:
Data plane Service Policy (Max Size 64)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# service-policy type data-plane <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1170
S Commandsservice-policy type data-plane
service-policy type qosservice-policy type qos <WORD>
Description: Qos Policy
Syntax:
Qos Service Policy (Max Size 64)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# service-policy type qos <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1171
S Commandsservice-policy type qos
serviceservice <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode <Available Modes>][svcredir <Service Redirection>] [service-type <Service Type>]
Description: Configure L4-L7 Service
Syntax:
Service node name (Max Size 64)WORD
(Optional) Tenant name (Max Size 63)WORD
(Optional) Device cluster name (Max Size 64)WORD
(Optional) Configure service node modeAvailable Modes
(Optional) Configure service redirectionService Redirection
(Optional) Configure service node typeService Type
Command Mode: l4l7 graph : Configure L4-L7 Service Graph
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>] [svcredir <Service Redirection>] [service-type <Service Type>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1172
S Commandsservice
session-record-flagssession-record-flags <sessionRecordFlags>
Description: Enable/Disable refresh in the session records, Comma separated values
Syntax:
Session record flags as comma separated values like val1,val2,..valN<sessionRecordFlags>
Command Mode: crypto webtoken : The cryptographic data used for generating and verifying web tokens.
Command Path:
# configure [['terminal', 't']](config)# crypto webtoken(config-webtoken)# session-record-flags <sessionRecordFlags>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1173
S Commandssession-record-flags
setset <propType> <propVal>
Description: Customize leaf aggregate policy values for Control Plane Policing
Syntax:
propTypepropType
propVal. Number range from=0 to=9223372036854775807propVal
Command Mode: policy-map type control-plane-leaf : Create leaf aggregate ControlPlane policy topolice/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type control-plane-leaf <WORD>(config-pmap-copp-leaf)# set <propType> <propVal>
set <propType> <propVal>
Description: Customize spine aggregate policy values for Control Plane Policing
Syntax:
propTypepropType
propVal. Number range from=0 to=9223372036854775807propVal
Command Mode: policy-map type control-plane-spine : Create spine aggregate ControlPlane policy topolice/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type control-plane-spine <WORD>(config-pmap-copp-spine)# set <propType> <propVal>
set qos-class <WORD>
Description: QOS level for the epg
Syntax:
QOS level for the epgqos-class
Qos LevelWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1174
S Commandsset
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# set qos-class <WORD>
set qos-class <WORD>
Description: QOS level for the application
Syntax:
QOS level for the applicationqos-class
Qos LevelWORD
Command Mode: application : application configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# set qos-class <WORD>
set qos-class <WORD>
Description: QOS level for the tunnel
Syntax:
QOS level for the tunnelqos-class
Qos LevelWORD
Command Mode: dot1q-tunnel : Tunnel configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# dot1q-tunnel <WORD>(config-tenant-tunnel)#set qos-class <WORD>
set qos-class <contractQosLevel>
Description: Specify the QOS level for the epg
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1175
S Commandsset
class of QOS to specifyqos-class
{unspecified|level1|level2|level3}<contractQosLevel>
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# set qos-class <contractQosLevel>
set qos-class <WORD>
Description: QOS level for the epg
Syntax:
QOS level for the epgqos-class
Qos LevelWORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# set qos-class <WORD>
set qos-class <contractQosLevel>
Description: QOS level for the epg
Syntax:
class of QOS to specifyqos-class
{unspecified|level1|level2|level3}<contractQosLevel>
Command Mode: oob-mgmt : Creates/Modify the out of band mgmt under the tenant mgmt
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>(config-oob-epg)# set qos-class <contractQosLevel>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1176
S Commandsset
set addcommunityset addcommunity regular|extended <value>
Description: Set BGP additional-community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set addcommunity regular|extended <value>
set addcommunity regular|extended <value>
Description: Set BGP additional-community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set addcommunity regular|extended <value>
set addcommunity regular|extended <value>
Description: Set BGP additional-community attribute
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1177
S Commandsset addcommunity
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set addcommunity regular|extended <value>
set addcommunity regular|extended <value>
Description: Set BGP additional-community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set addcommunity regular|extended <value>
set addcommunity regular|extended <value>
Description: Set BGP additional-community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1178
S Commandsset addcommunity
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set addcommunity regular|extended <value>
set addcommunity regular|extended <value>
Description: Set BGP additional-community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set addcommunity regular|extended <value>
set addcommunity regular|extended <value>
Description: Set BGP additional-community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1179
S Commandsset addcommunity
(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set addcommunity regular|extended <value>
set addcommunity regular|extended <value>
Description: Set BGP additional-community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set addcommunity regular|extended <value>
set addcommunity regular|extended <value>
Description: Set BGP additional-community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set addcommunity regular|extended <value>
set addcommunity regular|extended <value>
Description: Set BGP additional-community attribute
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1180
S Commandsset addcommunity
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set addcommunity regular|extended <value>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1181
S Commandsset addcommunity
set as-path prepend-last-asset as-path prepend-last-as <NUMBER>
Description: Prepend last AS to the as-path
Syntax:
Number of last-AS prepends. Number range from=1 to=10<1-10>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set as-path prepend-last-as <NUMBER>
set as-path prepend-last-as <NUMBER>
Description: Prepend last AS to the as-path
Syntax:
Number of last-AS prepends. Number range from=1 to=10<1-10>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set as-path prepend-last-as <NUMBER>
set as-path prepend-last-as <NUMBER>
Description: Prepend last AS to the as-path
Syntax:
Number of last-AS prepends. Number range from=1 to=10<1-10>
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1182
S Commandsset as-path prepend-last-as
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set as-path prepend-last-as <NUMBER>
set as-path prepend-last-as <NUMBER>
Description: Prepend last AS to the as-path
Syntax:
Number of last-AS prepends. Number range from=1 to=10<1-10>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set as-path prepend-last-as <NUMBER>
set as-path prepend-last-as <NUMBER>
Description: Prepend last AS to the as-path
Syntax:
Number of last-AS prepends. Number range from=1 to=10<1-10>
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set as-path prepend-last-as <NUMBER>
set as-path prepend-last-as <NUMBER>
Description: Prepend last AS to the as-path
Syntax:
Number of last-AS prepends. Number range from=1 to=10<1-10>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1183
S Commandsset as-path prepend-last-as
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set as-path prepend-last-as <NUMBER>
set as-path prepend-last-as <NUMBER>
Description: Prepend last AS to the as-path
Syntax:
Number of last-AS prepends. Number range from=1 to=10<1-10>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set as-path prepend-last-as <NUMBER>
set as-path prepend-last-as <NUMBER>
Description: Prepend last AS to the as-path
Syntax:
Number of last-AS prepends. Number range from=1 to=10<1-10>
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set as-path prepend-last-as <NUMBER>
set as-path prepend-last-as <NUMBER>
Description: Prepend last AS to the as-path
Syntax:
Number of last-AS prepends. Number range from=1 to=10<1-10>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1184
S Commandsset as-path prepend-last-as
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set as-path prepend-last-as <NUMBER>
set as-path prepend-last-as <NUMBER>
Description: Prepend last AS to the as-path
Syntax:
Number of last-AS prepends. Number range from=1 to=10<1-10>
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set as-path prepend-last-as <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1185
S Commandsset as-path prepend-last-as
set as-path prependset as-path prepend <1-4294967295>
Description: Prepend to the AS-Path
Syntax:
Prepend to the AS-Path<1-4294967295>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set as-path prepend <1-4294967295>
set as-path prepend <1-4294967295>
Description: Prepend to the AS-Path
Syntax:
Prepend to the AS-Path<1-4294967295>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set as-path prepend <1-4294967295>
set as-path prepend <1-4294967295>
Description: Prepend to the AS-Path
Syntax:
Prepend to the AS-Path<1-4294967295>
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1186
S Commandsset as-path prepend
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set as-path prepend <1-4294967295>
set as-path prepend <1-4294967295>
Description: Prepend to the AS-Path
Syntax:
Prepend to the AS-Path<1-4294967295>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set as-path prepend <1-4294967295>
set as-path prepend <1-4294967295>
Description: Prepend to the AS-Path
Syntax:
Prepend to the AS-Path<1-4294967295>
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set as-path prepend <1-4294967295>
set as-path prepend <1-4294967295>
Description: Prepend to the AS-Path
Syntax:
Prepend to the AS-Path<1-4294967295>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1187
S Commandsset as-path prepend
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set as-path prepend <1-4294967295>
set as-path prepend <1-4294967295>
Description: Prepend to the AS-Path
Syntax:
Prepend to the AS-Path<1-4294967295>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set as-path prepend <1-4294967295>
set as-path prepend <1-4294967295>
Description: Prepend to the AS-Path
Syntax:
Prepend to the AS-Path<1-4294967295>
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set as-path prepend <1-4294967295>
set as-path prepend <1-4294967295>
Description: Prepend to the AS-Path
Syntax:
Prepend to the AS-Path<1-4294967295>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1188
S Commandsset as-path prepend
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set as-path prepend <1-4294967295>
set as-path prepend <1-4294967295>
Description: Prepend to the AS-Path
Syntax:
Prepend to the AS-Path<1-4294967295>
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set as-path prepend <1-4294967295>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1189
S Commandsset as-path prepend
set burstset burst <0-549755813760> UNIT
Description: Burst Rate
Syntax:
Burst Rate<0-549755813760>
Burst Rate UnitUNIT
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set burst <0-549755813760> UNIT
set burst <0-549755813760> UNIT
Description: Burst Rate
Syntax:
Burst Rate<0-549755813760>
Burst Rate UnitUNIT
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set burst <0-549755813760> UNIT
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1190
S Commandsset burst
set cirset cir <0-4398046510080> UNIT
Description: Committed Rate
Syntax:
Committed Rate<0-4398046510080>
Committed Rate UnitUNIT
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set cir <0-4398046510080> UNIT
set cir <0-4398046510080> UNIT
Description: Committed Rate
Syntax:
Committed Rate<0-4398046510080>
Committed Rate UnitUNIT
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set cir <0-4398046510080> UNIT
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1191
S Commandsset cir
set communityset community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1192
S Commandsset community
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1193
S Commandsset community
Replace existing communityreplace
Do not change communitynone
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1194
S Commandsset community
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set community regular|extended <value>additive|replace|none
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1195
S Commandsset community
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1196
S Commandsset community
(config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1197
S Commandsset community
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set community regular|extended <value>additive|replace|none
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1198
S Commandsset community
set conform-cos-transmitset conform-cos-transmit <0-6>
Description: Conform Policer Mark Cos
Syntax:
Conform Policer Mark Cos<0-6>
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set conform-cos-transmit <0-6>
set conform-cos-transmit <0-6>
Description: Conform Policer Mark Cos
Syntax:
Conform Policer Mark Cos<0-6>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set conform-cos-transmit <0-6>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1199
S Commandsset conform-cos-transmit
set conform-dscp-transmitset conform-dscp-transmit <0-63>
Description: Conform Policer Mark DSCP
Syntax:
Conform Policer Mark DSCP<0-63>
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set conform-dscp-transmit <0-63>
set conform-dscp-transmit <0-63>
Description: Conform Policer Mark DSCP
Syntax:
Conform Policer Mark DSCP<0-63>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set conform-dscp-transmit <0-63>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1200
S Commandsset conform-dscp-transmit
set conformset conform <WORD>
Description: Conform Policer Action
Syntax:
Conform Policer ActionWORD
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set conform <WORD>
set conform <WORD>
Description: Conform Policer Action
Syntax:
Conform Policer ActionWORD
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set conform <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1201
S Commandsset conform
set dampeningset dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Route Flap dampening
Syntax:
Decay half life. Number range from=1 to=60<1-60>
Value to start reusing a route. Number range from=1 to=20000<1-20000>
Value to start suppressing a route. Number range from=1 to=20000<1-20000>
Maximum suppress time for stable route. Number range from=1 to=255<1-255>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Route Flap dampening
Syntax:
Decay half life. Number range from=1 to=60<1-60>
Value to start reusing a route. Number range from=1 to=20000<1-20000>
Value to start suppressing a route. Number range from=1 to=20000<1-20000>
Maximum suppress time for stable route. Number range from=1 to=255<1-255>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1202
S Commandsset dampening
set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Route Flap dampening
Syntax:
Decay half life. Number range from=1 to=60<1-60>
Value to start reusing a route. Number range from=1 to=20000<1-20000>
Value to start suppressing a route. Number range from=1 to=20000<1-20000>
Maximum suppress time for stable route. Number range from=1 to=255<1-255>
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Route Flap dampening
Syntax:
Decay half life. Number range from=1 to=60<1-60>
Value to start reusing a route. Number range from=1 to=20000<1-20000>
Value to start suppressing a route. Number range from=1 to=20000<1-20000>
Maximum suppress time for stable route. Number range from=1 to=255<1-255>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Route Flap dampening
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1203
S Commandsset dampening
Syntax:
Decay half life. Number range from=1 to=60<1-60>
Value to start reusing a route. Number range from=1 to=20000<1-20000>
Value to start suppressing a route. Number range from=1 to=20000<1-20000>
Maximum suppress time for stable route. Number range from=1 to=255<1-255>
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Route Flap dampening
Syntax:
Decay half life. Number range from=1 to=60<1-60>
Value to start reusing a route. Number range from=1 to=20000<1-20000>
Value to start suppressing a route. Number range from=1 to=20000<1-20000>
Maximum suppress time for stable route. Number range from=1 to=255<1-255>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Route Flap dampening
Syntax:
Decay half life. Number range from=1 to=60<1-60>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1204
S Commandsset dampening
Value to start reusing a route. Number range from=1 to=20000<1-20000>
Value to start suppressing a route. Number range from=1 to=20000<1-20000>
Maximum suppress time for stable route. Number range from=1 to=255<1-255>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Route Flap dampening
Syntax:
Decay half life. Number range from=1 to=60<1-60>
Value to start reusing a route. Number range from=1 to=20000<1-20000>
Value to start suppressing a route. Number range from=1 to=20000<1-20000>
Maximum suppress time for stable route. Number range from=1 to=255<1-255>
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Route Flap dampening
Syntax:
Decay half life. Number range from=1 to=60<1-60>
Value to start reusing a route. Number range from=1 to=20000<1-20000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1205
S Commandsset dampening
Value to start suppressing a route. Number range from=1 to=20000<1-20000>
Maximum suppress time for stable route. Number range from=1 to=255<1-255>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Route Flap dampening
Syntax:
Decay half life. Number range from=1 to=60<1-60>
Value to start reusing a route. Number range from=1 to=20000<1-20000>
Value to start suppressing a route. Number range from=1 to=20000<1-20000>
Maximum suppress time for stable route. Number range from=1 to=255<1-255>
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1206
S Commandsset dampening
set dscp-codeset dscp-code <dscp-prop> <dscp-val>
Description: Set DSCP Class translation values
Syntax:
DSCP Class Namedscp-prop
Dscp valdscp-val
Command Mode: qos : Set DSCP Class translation values
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# qos dscp-map <WORD>(config-qos-cmap)# set dscp-code <dscp-prop> <dscp-val>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1207
S Commandsset dscp-code
set dscpset dscp <WORD>
Description: Specify the DSCP level for the EPG
Syntax:
DSCP valueWORD
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# set dscp <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1208
S Commandsset dscp
set exceed-cos-transmitset exceed-cos-transmit <0-6>
Description: Exceed Policer Mark Cos
Syntax:
Exceed Policer Mark Cos<0-6>
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set exceed-cos-transmit <0-6>
set exceed-cos-transmit <0-6>
Description: Exceed Policer Mark Cos
Syntax:
Exceed Policer Mark Cos<0-6>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set exceed-cos-transmit <0-6>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1209
S Commandsset exceed-cos-transmit
set exceed-dscp-transmitset exceed-dscp-transmit <0-63>
Description: Exceed Policer Mark DSCP
Syntax:
Exceed Policer Mark DSCP<0-63>
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set exceed-dscp-transmit <0-63>
set exceed-dscp-transmit <0-63>
Description: Exceed Policer Mark DSCP
Syntax:
Exceed Policer Mark DSCP<0-63>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set exceed-dscp-transmit <0-63>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1210
S Commandsset exceed-dscp-transmit
set exceedset exceed <WORD>
Description: Exceed Policer Action
Syntax:
Exceed Policer ActionWORD
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set exceed <WORD>
set exceed <WORD>
Description: Exceed Policer Action
Syntax:
Exceed Policer ActionWORD
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set exceed <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1211
S Commandsset exceed
set excessive-burstset excessive-burst <0-549755813760> UNIT
Description: Excessive Burst Rate
Syntax:
Excessive Burst Rate<0-549755813760>
Excessive Burst Rate UnitUNIT
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set excessive-burst <0-549755813760> UNIT
set excessive-burst <0-549755813760> UNIT
Description: Excessive Burst Rate
Syntax:
Excessive Burst Rate<0-549755813760>
Excessive Burst Rate UnitUNIT
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set excessive-burst <0-549755813760> UNIT
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1212
S Commandsset excessive-burst
set local-preferenceset local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1213
S Commandsset local-preference
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1214
S Commandsset local-preference
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1215
S Commandsset local-preference
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1216
S Commandsset local-preference
set metric-typeset metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1217
S Commandsset metric-type
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1218
S Commandsset metric-type
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1219
S Commandsset metric-type
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set metric-type <metric-type>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1220
S Commandsset metric-type
set metricset metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1221
S Commandsset metric
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1222
S Commandsset metric
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1223
S Commandsset metric
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set metric <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1224
S Commandsset metric
set modeset mode <WORD>
Description: Policer Mode
Syntax:
Policer ModeWORD
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set mode <WORD>
set mode <WORD>
Description: Policer Mode
Syntax:
Policer ModeWORD
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set mode <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1225
S Commandsset mode
set next-hopset next-hop <IPv4 or IPv6 address>
Description: Set next hop for destination routing protocol
Syntax:
Next hop addressIPv4 or IPv6 address
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set next-hop <IPv4 or IPv6 address>
set next-hop <IPv4 or IPv6 address>
Description: Set next hop address
Syntax:
Next hop addressIPv4 or IPv6 address
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set next-hop <IPv4 or IPv6 address>
set next-hop <IPv4 or IPv6 address>
Description: Set next hop address
Syntax:
Next hop addressIPv4 or IPv6 address
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1226
S Commandsset next-hop
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set next-hop <IPv4 or IPv6 address>
set next-hop <IPv4 or IPv6 address>
Description: Set next hop address
Syntax:
Next hop addressIPv4 or IPv6 address
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set next-hop <IPv4 or IPv6 address>
set next-hop <IPv4 or IPv6 address>
Description: Set next hop address
Syntax:
Next hop addressIPv4 or IPv6 address
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set next-hop <IPv4 or IPv6 address>
set next-hop <IPv4 or IPv6 address>
Description: Set next hop address
Syntax:
Next hop addressIPv4 or IPv6 address
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1227
S Commandsset next-hop
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set next-hop <IPv4 or IPv6 address>
set next-hop <IPv4 or IPv6 address>
Description: Set next hop address
Syntax:
Next hop addressIPv4 or IPv6 address
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set next-hop <IPv4 or IPv6 address>
set next-hop <IPv4 or IPv6 address>
Description: Set next hop address
Syntax:
Next hop addressIPv4 or IPv6 address
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set next-hop <IPv4 or IPv6 address>
set next-hop <IPv4 or IPv6 address>
Description: Set next hop address
Syntax:
Next hop addressIPv4 or IPv6 address
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1228
S Commandsset next-hop
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set next-hop <IPv4 or IPv6 address>
set next-hop <IPv4 or IPv6 address>
Description: Set next hop address
Syntax:
Next hop addressIPv4 or IPv6 address
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set next-hop <IPv4 or IPv6 address>
set next-hop <IPv4 or IPv6 address>
Description: Set next hop address
Syntax:
Next hop addressIPv4 or IPv6 address
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set next-hop <IPv4 or IPv6 address>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1229
S Commandsset next-hop
set pirset pir <0-4398046510080> UNIT
Description: Peak Rate
Syntax:
Peak Rate<0-4398046510080>
Pir UnitUNIT
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set pir <0-4398046510080> UNIT
set pir <0-4398046510080> UNIT
Description: Peak Rate
Syntax:
Peak Rate<0-4398046510080>
Pir UnitUNIT
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set pir <0-4398046510080> UNIT
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1230
S Commandsset pir
set qos-classset qos-class <WORD>
Description: Class of QOS to specify
Syntax:
Qos LevelWORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# set qos-class <WORD>
set qos-class <WORD> WORD
Description: Class of QOS to specify
Syntax:
Qos LevelWORD
Target QOS DirectionWORD
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# set qos-class <WORD> WORD
set qos-class unspecified|level1|level2|level3
Description: Specify the QOS level for the EPG
Syntax:
Unspecified QoS levelunspecified
QoS level1level1
QoS level2level2
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1231
S Commandsset qos-class
QoS level3level3
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# set qos-class unspecified|level1|level2|level3
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1232
S Commandsset qos-class
set tagset tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1233
S Commandsset tag
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1234
S Commandsset tag
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1235
S Commandsset tag
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set tag <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1236
S Commandsset tag
set target-dscpset target-dscp <WORD>
Description: class of target dscp to specify
Syntax:
Target dscpWORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# set target-dscp <WORD>
set target-dscp <WORD> WORD
Description: class of target dscp to specify
Syntax:
Target dscpWORD
Target DSCP DirectionWORD
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# set target-dscp <WORD> WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1237
S Commandsset target-dscp
set typeset type <WORD>
Description: Policer type
Syntax:
Policer TypeWORD
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set type <WORD>
set type <WORD>
Description: Policer type
Syntax:
Policer TypeWORD
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set type <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1238
S Commandsset type
set violate-cos-transmitset violate-cos-transmit <0-6>
Description: Violate Policer Mark Cos
Syntax:
Violate Policer Mark Cos<0-6>
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set violate-cos-transmit <0-6>
set violate-cos-transmit <0-6>
Description: Violate Policer Mark Cos
Syntax:
Violate Policer Mark Cos<0-6>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set violate-cos-transmit <0-6>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1239
S Commandsset violate-cos-transmit
set violate-dscp-transmitset violate-dscp-transmit <0-63>
Description: Violate Policer Mark DSCP
Syntax:
Violate Policer Mark DSCP<0-63>
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set violate-dscp-transmit <0-63>
set violate-dscp-transmit <0-63>
Description: Violate Policer Mark DSCP
Syntax:
Violate Policer Mark DSCP<0-63>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set violate-dscp-transmit <0-63>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1240
S Commandsset violate-dscp-transmit
set violateset violate <WORD>
Description: Violate Policer Action
Syntax:
Violate Policer ActionWORD
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set violate <WORD>
set violate <WORD>
Description: Violate Policer Action
Syntax:
Violate Policer ActionWORD
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set violate <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1241
S Commandsset violate
set weightset weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1242
S Commandsset weight
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1243
S Commandsset weight
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD> <WORD> <NUMBER>(config-leaf-vrf-template-route-profile)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1244
S Commandsset weight
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>](config-leaf-vrf-route-map-match)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny](config-leaf-vrf-route-map-match)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Command Mode: match route group : Route group
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match route group <> [order <order>] [deny](config-leaf-vrf-route-map-match)# set weight <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1245
S Commandsset weight
shellinaboxshellinabox
Description: Configures the communication policy of the SHELLINABOX feature
Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https
Usage:
In the APIC GUI, the SHELLINABOX feature allows you to open a pop-up SSH session to a fabric switchby right-clicking the icon of the switch. To enable or disable this feature, use the shellinabox command toenter the SHELLINABOX communication policy group, then use the [no] admin-state-enable command.
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# shellinabox
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1246
S Commandsshellinabox
show aaa authenticationshow aaa authentication
Description: Show AAA Authentication information
Command Mode: exec : Exec Mode
Command Path:
# show aaa authentication
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1247
S Commandsshow aaa authentication
show aaa groupsshow aaa groups
Description: Show AAA group information
Command Mode: exec : Exec Mode
Command Path:
# show aaa groups
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1248
S Commandsshow aaa groups
show access-listshow access-list WORD
Description: Show Access-list Information
Syntax:
Name of the Contract to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show access-list WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1249
S Commandsshow access-list
show accounting logshow accounting log
Description: CLI configuration command logs
Command Mode: exec : Exec Mode
Command Path:
# show accounting log
NOTE:
This command displays only those changes made using the command line interface (CLI). It does not displaychanges made using the GUI or the API. To view all changes made in the Management Information Tree, usethe show audit detail command.
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1250
S Commandsshow accounting log
show acllog deny l2 flowshow acllog deny l2 flow
Description: l3 flow information
Command Mode: exec : Exec Mode
Command Path:
# show acllog deny l2 flow
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1251
S Commandsshow acllog deny l2 flow
show acllog deny l2 flow tenant vrfshow acllog deny l2 flow tenant <WORD> vrf [vlan <NUMBER>] [srcIntf <srcintf>] <WORD>
Description: tenant vrf information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) source Interfacesrcintf
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show acllog deny l2 flow tenant <WORD> vrf [vlan <NUMBER>] [srcIntf <srcintf>] <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1252
S Commandsshow acllog deny l2 flow tenant vrf
show acllog deny l2 flow tenant vrf detailshow acllog deny l2 flow tenant <WORD> vrf [vlan <NUMBER>] [srcIntf <srcintf>] <WORD> detail [srcmac<E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Description: detail information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) source Interfacesrcintf
Name of the VRF to filter on (Max Size 64)WORD
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: exec : Exec Mode
Command Path:
# show acllog deny l2 flow tenant <WORD> vrf [vlan <NUMBER>] [srcIntf <srcintf>] <WORD>detail [srcmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1253
S Commandsshow acllog deny l2 flow tenant vrf detail
show acllog deny l2 pktshow acllog deny l2 pkt
Description: Pkt command
Command Mode: exec : Exec Mode
Command Path:
# show acllog deny l2 pkt
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1254
S Commandsshow acllog deny l2 pkt
show acllog deny l2 pkt tenant vrfshow acllog deny l2 pkt tenant <WORD> vrf <WORD> [start-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>][end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [vlan <NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>]
Description: Vrf Name
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the vrf to filter on (Max Size 64)WORD
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) Source Interfacesrcintf
(Optional) packet length. Number range from=1 to=65535<1-65535>
Command Mode: exec : Exec Mode
Command Path:
# show acllog deny l2 pkt tenant <WORD> vrf <WORD> [start-time time-stamp<YYYY-MM-DDTHR:MIN:SEC>] [end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [vlan <NUMBER>][srcintf <srcintf>] [pktlen <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1255
S Commandsshow acllog deny l2 pkt tenant vrf
show acllog deny l2 pkt tenant vrf detailshow acllog deny l2 pkt tenant <WORD> vrf <WORD> [start-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>][end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [vlan <NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>]detail [srcmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Description: Detail information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the vrf to filter on (Max Size 64)WORD
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) Source Interfacesrcintf
(Optional) packet length. Number range from=1 to=65535<1-65535>
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: exec : Exec Mode
Command Path:
# show acllog deny l2 pkt tenant <WORD> vrf <WORD> [start-time time-stamp<YYYY-MM-DDTHR:MIN:SEC>] [end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [vlan <NUMBER>][srcintf <srcintf>] [pktlen <NUMBER>] detail [srcmac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1256
S Commandsshow acllog deny l2 pkt tenant vrf detail
show acllog deny l3 flowshow acllog deny l3 flow
Description: l3 flow information
Command Mode: exec : Exec Mode
Command Path:
# show acllog deny l3 flow
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1257
S Commandsshow acllog deny l3 flow
show acllog deny l3 flow tenant vrfshow acllog deny l3 flow tenant <WORD> vrf [srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.D or A:B::C:D>][protocol <Protocol>] [srcport <SrcPort>] [dstport <DstPort>] [srcintf <srcintf>] <WORD>
Description: tenant vrf information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) ProtocolProtocol
(Optional) source portSrcPort
(Optional) destination portDstPort
(Optional) source interfacesrcintf
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show acllog deny l3 flow tenant <WORD> vrf [srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.Dor A:B::C:D>] [protocol <Protocol>] [srcport <SrcPort>] [dstport <DstPort>] [srcintf<srcintf>] <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1258
S Commandsshow acllog deny l3 flow tenant vrf
show acllog deny l3 flow tenant vrf detailshow acllog deny l3 flow tenant <WORD> vrf [srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.D or A:B::C:D>][protocol <Protocol>] [srcport <SrcPort>] [dstport <DstPort>] [srcintf <srcintf>] <WORD> detail [srcmac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Description: detail information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) ProtocolProtocol
(Optional) source portSrcPort
(Optional) destination portDstPort
(Optional) source interfacesrcintf
Name of the VRF to filter on (Max Size 64)WORD
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: exec : Exec Mode
Command Path:
# show acllog deny l3 flow tenant <WORD> vrf [srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.Dor A:B::C:D>] [protocol <Protocol>] [srcport <SrcPort>] [dstport <DstPort>] [srcintf<srcintf>] <WORD> detail [srcmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [dstmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1259
S Commandsshow acllog deny l3 flow tenant vrf detail
show acllog deny l3 pktshow acllog deny l3 pkt
Description: Pkt command
Command Mode: exec : Exec Mode
Command Path:
# show acllog deny l3 pkt
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1260
S Commandsshow acllog deny l3 pkt
show acllog deny l3 pkt tenant vrfshow acllog deny l3 pkt tenant <WORD> vrf <WORD> [start-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>][end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [protocol <protocol>] [srcip <A.B.C.D or A:B::C:D>][dstip <A.B.C.D or A:B::C:D>] [srcport <NUMBER>] [dstport <NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>]
Description: Vrf Name
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the vrf to filter on (Max Size 64)WORD
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) protocolprotocol
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) Source port. Number range from=0 to=65535<0-65535>
(Optional) Destination port. Number range from=0 to=65535<0-65535>
(Optional) source Interfacesrcintf
(Optional) packet length. Number range from=1 to=65535<1-65535>
Command Mode: exec : Exec Mode
Command Path:
# show acllog deny l3 pkt tenant <WORD> vrf <WORD> [start-time time-stamp<YYYY-MM-DDTHR:MIN:SEC>] [end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [protocol <protocol>][srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.D or A:B::C:D>] [srcport <NUMBER>] [dstport<NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1261
S Commandsshow acllog deny l3 pkt tenant vrf
show acllog deny l3 pkt tenant vrf detailshow acllog deny l3 pkt tenant <WORD> vrf <WORD> [start-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>][end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [protocol <protocol>] [srcip <A.B.C.D or A:B::C:D>][dstip <A.B.C.D or A:B::C:D>] [srcport <NUMBER>] [dstport <NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>]detail [srcmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Description: Detail information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the vrf to filter on (Max Size 64)WORD
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) protocolprotocol
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) Source port. Number range from=0 to=65535<0-65535>
(Optional) Destination port. Number range from=0 to=65535<0-65535>
(Optional) source Interfacesrcintf
(Optional) packet length. Number range from=1 to=65535<1-65535>
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: exec : Exec Mode
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1262
S Commandsshow acllog deny l3 pkt tenant vrf detail
Command Path:
# show acllog deny l3 pkt tenant <WORD> vrf <WORD> [start-time time-stamp<YYYY-MM-DDTHR:MIN:SEC>] [end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [protocol <protocol>][srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.D or A:B::C:D>] [srcport <NUMBER>] [dstport<NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>] detail [srcmac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1263
S Commandsshow acllog deny l3 pkt tenant vrf detail
show acllog permit l2 flow tenant vrfshow acllog permit l2 flow tenant <WORD> vrf [vlan <NUMBER>] [srcintf <srcintf>] <WORD>
Description: tenant vrf information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) source interfacesrcintf
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show acllog permit l2 flow tenant <WORD> vrf [vlan <NUMBER>] [srcintf <srcintf>] <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1264
S Commandsshow acllog permit l2 flow tenant vrf
show acllog permit l2 flow tenant vrf detailshow acllog permit l2 flow tenant <WORD> vrf [vlan <NUMBER>] [srcintf <srcintf>] <WORD> detail [srcmac<E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Description: detail information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) source interfacesrcintf
Name of the VRF to filter on (Max Size 64)WORD
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: exec : Exec Mode
Command Path:
# show acllog permit l2 flow tenant <WORD> vrf [vlan <NUMBER>] [srcintf <srcintf>] <WORD>detail [srcmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1265
S Commandsshow acllog permit l2 flow tenant vrf detail
show acllog permit l2 pkt tenant vrfshow acllog permit l2 pkt tenant <WORD> vrf <WORD> [start-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>][end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [vlan <NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>]
Description: Vrf Name
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the vrf to filter on (Max Size 64)WORD
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) source Interfacesrcintf
(Optional) packet length. Number range from=1 to=65535<1-65535>
Command Mode: exec : Exec Mode
Command Path:
# show acllog permit l2 pkt tenant <WORD> vrf <WORD> [start-time time-stamp<YYYY-MM-DDTHR:MIN:SEC>] [end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [vlan <NUMBER>][srcintf <srcintf>] [pktlen <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1266
S Commandsshow acllog permit l2 pkt tenant vrf
show acllog permit l2 pkt tenant vrf detailshow acllog permit l2 pkt tenant <WORD> vrf <WORD> [start-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>][end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [vlan <NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>]detail [srcmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Description: Detail information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the vrf to filter on (Max Size 64)WORD
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) source Interfacesrcintf
(Optional) packet length. Number range from=1 to=65535<1-65535>
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: exec : Exec Mode
Command Path:
# show acllog permit l2 pkt tenant <WORD> vrf <WORD> [start-time time-stamp<YYYY-MM-DDTHR:MIN:SEC>] [end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [vlan <NUMBER>][srcintf <srcintf>] [pktlen <NUMBER>] detail [srcmac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1267
S Commandsshow acllog permit l2 pkt tenant vrf detail
show acllog permit l3 flow tenant vrfshow acllog permit l3 flow tenant <WORD> vrf [srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.D or A:B::C:D>][protocol <Protocol>] [srcport <SrcPort>] [dstport <DstPort>] [srcintf <srcintf>] <WORD>
Description: tenant vrf information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) ProtocolProtocol
(Optional) source portSrcPort
(Optional) destination portDstPort
(Optional) source interfacesrcintf
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show acllog permit l3 flow tenant <WORD> vrf [srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.Dor A:B::C:D>] [protocol <Protocol>] [srcport <SrcPort>] [dstport <DstPort>] [srcintf<srcintf>] <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1268
S Commandsshow acllog permit l3 flow tenant vrf
show acllog permit l3 flow tenant vrf detailshow acllog permit l3 flow tenant <WORD> vrf [srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.D or A:B::C:D>][protocol <Protocol>] [srcport <SrcPort>] [dstport <DstPort>] [srcintf <srcintf>] <WORD> detail [srcmac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Description: detail information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) ProtocolProtocol
(Optional) source portSrcPort
(Optional) destination portDstPort
(Optional) source interfacesrcintf
Name of the VRF to filter on (Max Size 64)WORD
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: exec : Exec Mode
Command Path:
# show acllog permit l3 flow tenant <WORD> vrf [srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.Dor A:B::C:D>] [protocol <Protocol>] [srcport <SrcPort>] [dstport <DstPort>] [srcintf<srcintf>] <WORD> detail [srcmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [dstmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1269
S Commandsshow acllog permit l3 flow tenant vrf detail
show acllog permit l3 pkt tenant vrfshow acllog permit l3 pkt tenant <WORD> vrf <WORD> [start-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>][end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [protocol <protocol>] [srcip <A.B.C.D or A:B::C:D>][dstip <A.B.C.D or A:B::C:D>] [srcport <NUMBER>] [dstport <NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>]
Description: Vrf Name
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the vrf to filter on (Max Size 64)WORD
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) protocolprotocol
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) Source port. Number range from=0 to=65535<0-65535>
(Optional) Destination port. Number range from=0 to=65535<0-65535>
(Optional) source Interfacesrcintf
(Optional) packet length. Number range from=1 to=65535<1-65535>
Command Mode: exec : Exec Mode
Command Path:
# show acllog permit l3 pkt tenant <WORD> vrf <WORD> [start-time time-stamp<YYYY-MM-DDTHR:MIN:SEC>] [end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [protocol <protocol>][srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.D or A:B::C:D>] [srcport <NUMBER>] [dstport<NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1270
S Commandsshow acllog permit l3 pkt tenant vrf
show acllog permit l3 pkt tenant vrf detailshow acllog permit l3 pkt tenant <WORD> vrf <WORD> [start-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>][end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [protocol <protocol>] [srcip <A.B.C.D or A:B::C:D>][dstip <A.B.C.D or A:B::C:D>] [srcport <NUMBER>] [dstport <NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>]detail [srcmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Description: Detail information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the vrf to filter on (Max Size 64)WORD
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Event activity in time intervaltime-stamp<YYYY-MM-DDTHR:MIN:SEC>
(Optional) protocolprotocol
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) IP address in format i.i.i.i or IPv6 address in formatxxxx:xxxx, xxxx::xx
A.B.C.D or A:B::C:D
(Optional) Source port. Number range from=0 to=65535<0-65535>
(Optional) Destination port. Number range from=0 to=65535<0-65535>
(Optional) source Interfacesrcintf
(Optional) packet length. Number range from=1 to=65535<1-65535>
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: exec : Exec Mode
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1271
S Commandsshow acllog permit l3 pkt tenant vrf detail
Command Path:
# show acllog permit l3 pkt tenant <WORD> vrf <WORD> [start-time time-stamp<YYYY-MM-DDTHR:MIN:SEC>] [end-time time-stamp <YYYY-MM-DDTHR:MIN:SEC>] [protocol <protocol>][srcip <A.B.C.D or A:B::C:D>] [dstip <A.B.C.D or A:B::C:D>] [srcport <NUMBER>] [dstport<NUMBER>] [srcintf <srcintf>] [pktlen <NUMBER>] detail [srcmac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [dstmac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1272
S Commandsshow acllog permit l3 pkt tenant vrf detail
show analyticsshow analytics
Description: Show analytics cluster configuration
Command Mode: exec : Exec Mode
Command Path:
# show analytics
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1273
S Commandsshow analytics
show applicationshow application WORD
Description: Show Application Profiles Information
Syntax:
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show application WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1274
S Commandsshow application
show auditsshow audits [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show audit-log information
Syntax:
(Optional) Log ID<log-id>
(Optional) Object action indicatoraction<action-type>
(Optional) Name of user<user-name>
(Optional) Logs created in time interval. Number range from=1 to=59<num-minutes>
(Optional) Logs created in time interval. Number range from=1 to=23<num-hours>
(Optional) Logs created in time interval. Number range from=1 to=999<num-days>
(Optional) Logs created in time interval<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Logs created in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Detailed audit-log information. Displays what was modifiedand displays the old and new settings.
detail
command scope<scope>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1275
S Commandsshow audits
show audits tenantshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1276
S Commandsshow audits tenant
show audits tenant applicationshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1277
S Commandsshow audits tenant application
show audits tenant application epgshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1278
S Commandsshow audits tenant application epg
show audits tenant bridge-domainshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1279
S Commandsshow audits tenant bridge-domain
show audits tenant bridge-domain detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1280
S Commandsshow audits tenant bridge-domain detail
show audits tenant bridge-domain first-hop-securitybinding-table
show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security binding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-securitybinding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1281
S Commandsshow audits tenant bridge-domain first-hop-security binding-table
show audits tenant bridge-domain first-hop-security statisticsarp
show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statistics arp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-securitystatistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1282
S Commandsshow audits tenant bridge-domain first-hop-security statistics arp
show audits tenant bridge-domain first-hop-security statisticsdhcpv4
show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statisticsdhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-securitystatistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1283
S Commandsshow audits tenant bridge-domain first-hop-security statistics dhcpv4
show audits tenant bridge-domain first-hop-security statisticsdhcpv6
show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statisticsdhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-securitystatistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1284
S Commandsshow audits tenant bridge-domain first-hop-security statistics dhcpv6
show audits tenant bridge-domain first-hop-security statisticsneighbor-discovery
show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statisticsneighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-securitystatistics neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1285
S Commandsshow audits tenant bridge-domain first-hop-security statistics neighbor-discovery
show audits tenant dnsservergroupshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD
Description: Show Dns Server Group Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1286
S Commandsshow audits tenant dnsservergroup
show audits tenant dnsservergroup servershow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD server WORD
Description: Show Dns Server Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD server WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1287
S Commandsshow audits tenant dnsservergroup server
show audits tenant dnsservergroup server domainshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD server WORD domain WORD
Description: Show Dns Domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Domain we eventually want to filter on (Max Size 512)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD server WORD domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1288
S Commandsshow audits tenant dnsservergroup server domain
show audits tenant interface bridge-domainshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1289
S Commandsshow audits tenant interface bridge-domain
show audits tenant interface bridge-domain detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1290
S Commandsshow audits tenant interface bridge-domain detail
show audits tenant interface bridge-domain first-hop-securitybinding-table
show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitybinding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitybinding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1291
S Commandsshow audits tenant interface bridge-domain first-hop-security binding-table
show audits tenant interface bridge-domain first-hop-securitystatistics arp
show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics arp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1292
S Commandsshow audits tenant interface bridge-domain first-hop-security statistics arp
show audits tenant interface bridge-domain first-hop-securitystatistics dhcpv4
show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics dhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1293
S Commandsshow audits tenant interface bridge-domain first-hop-security statistics dhcpv4
show audits tenant interface bridge-domain first-hop-securitystatistics dhcpv6
show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics dhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1294
S Commandsshow audits tenant interface bridge-domain first-hop-security statistics dhcpv6
show audits tenant interface bridge-domain first-hop-securitystatistics neighbor-discovery
show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics neighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1295
S Commandsshow audits tenant interface bridge-domain first-hop-security statistics neighbor-discovery
show audits tenant multicast-route-mapsshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD multicast-route-maps
Description: Show multicast route-maps per Tenant
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD multicast-route-maps
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1296
S Commandsshow audits tenant multicast-route-maps
show audits tenant vrfshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Description: Show VRF Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1297
S Commandsshow audits tenant vrf
show audits tenant vrf acllog l2show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD acllog <permitDrop> l2 flow vlan <NUMBER>srcintf <srcintf>
Description: L2 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flowi statsflow
vlan infovlan
<vlan>. Number range from=0 to=9223372036854775807<vlan>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD acllog <permitDrop> l2 flow vlan<NUMBER> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1298
S Commandsshow audits tenant vrf acllog l2
show audits tenant vrf acllog l3show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD acllog <permitDrop> l3 flow srcip <A.B.C.Dor A:B::C:D> dstip <A.B.C.D or A:B::C:D> proto <proto> srcport <srcport> dstport <dstport> srcintf <srcintf>
Description: L3 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flow statsflow
source ipsrcip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
destination ipdstip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
protocolproto
<proto><proto>
source portsrcport
<srcport><srcport>
destination portdstport
<dstport><dstport>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD acllog <permitDrop> l3 flow srcip
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1299
S Commandsshow audits tenant vrf acllog l3
<A.B.C.D or A:B::C:D> dstip <A.B.C.D or A:B::C:D> proto <proto> srcport <srcport> dstport<dstport> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1300
S Commandsshow audits tenant vrf acllog l3
show audits tenant vrf detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1301
S Commandsshow audits tenant vrf detail
show audits tenant vrf external-l3 bgpshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Description: Show command for BGP peers
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1302
S Commandsshow audits tenant vrf external-l3 bgp
show audits tenant vrf external-l3 bgp nodeshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1303
S Commandsshow audits tenant vrf external-l3 bgp node
show audits tenant vrf external-l3 eigrpshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Description: Show external l3 EIGRP
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1304
S Commandsshow audits tenant vrf external-l3 eigrp
show audits tenant vrf external-l3 eigrp detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1305
S Commandsshow audits tenant vrf external-l3 eigrp detail
show audits tenant vrf external-l3 epgshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Description: Show command for external-l3 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1306
S Commandsshow audits tenant vrf external-l3 epg
show audits tenant vrf external-l3 epg detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1307
S Commandsshow audits tenant vrf external-l3 epg detail
show audits tenant vrf external-l3 epg nameshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: EPG name to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1308
S Commandsshow audits tenant vrf external-l3 epg name
show audits tenant vrf external-l3 epg name detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1309
S Commandsshow audits tenant vrf external-l3 epg name detail
show audits tenant vrf external-l3 interfacesshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1310
S Commandsshow audits tenant vrf external-l3 interfaces
show audits tenant vrf external-l3 interfaces detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show interfaces details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1311
S Commandsshow audits tenant vrf external-l3 interfaces detail
show audits tenant vrf external-l3 ospfshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Description: Show command for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1312
S Commandsshow audits tenant vrf external-l3 ospf
show audits tenant vrf external-l3 ospf detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Description: Show internal details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1313
S Commandsshow audits tenant vrf external-l3 ospf detail
show audits tenant vrf external-l3 static-routeshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Description: Show command for external-l3 static routes
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1314
S Commandsshow audits tenant vrf external-l3 static-route
show audits tenant vrf external-l3 static-route detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1315
S Commandsshow audits tenant vrf external-l3 static-route detail
show audits tenant vrf external-l3 static-route nodeshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1316
S Commandsshow audits tenant vrf external-l3 static-route node
show audits tenant vrf external-l3 static-route node detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1317
S Commandsshow audits tenant vrf external-l3 static-route node detail
show audits tenant vrf multicastshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD multicast
Description: Show multicast configuration per VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD multicast
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1318
S Commandsshow audits tenant vrf multicast
show bridge-domainshow bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1319
S Commandsshow bridge-domain
show bridge-domain detailshow bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1320
S Commandsshow bridge-domain detail
show bridge-domain first-hop-security binding-tableshow bridge-domain WORD first-hop-security binding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show bridge-domain WORD first-hop-security binding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1321
S Commandsshow bridge-domain first-hop-security binding-table
show bridge-domain first-hop-security statistics arpshow bridge-domain WORD first-hop-security statistics arp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show bridge-domain WORD first-hop-security statistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1322
S Commandsshow bridge-domain first-hop-security statistics arp
show bridge-domain first-hop-security statistics dhcpv4show bridge-domain WORD first-hop-security statistics dhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show bridge-domain WORD first-hop-security statistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1323
S Commandsshow bridge-domain first-hop-security statistics dhcpv4
show bridge-domain first-hop-security statistics dhcpv6show bridge-domain WORD first-hop-security statistics dhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show bridge-domain WORD first-hop-security statistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1324
S Commandsshow bridge-domain first-hop-security statistics dhcpv6
show bridge-domain first-hop-security statisticsneighbor-discovery
show bridge-domain WORD first-hop-security statistics neighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show bridge-domain WORD first-hop-security statistics neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1325
S Commandsshow bridge-domain first-hop-security statistics neighbor-discovery
show callhomeshow callhome common
Description: Show command for callhome
Syntax:
Commoncommon
Command Mode: exec : Exec Mode
Command Path:
# show callhome common
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1326
S Commandsshow callhome
show callhome common destination-profileshow callhome common destination-profile
Description: Show command for callhome destination-profile
Syntax:
Commoncommon
Command Mode: exec : Exec Mode
Command Path:
# show callhome common destination-profile
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1327
S Commandsshow callhome common destination-profile
show callhome common query-profileshow callhome common query-profile
Description: Show command for callhome destination-profile
Syntax:
Commoncommon
Command Mode: exec : Exec Mode
Command Path:
# show callhome common query-profile
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1328
S Commandsshow callhome common query-profile
show callhome common transport-emailshow callhome common transport-email
Description: Show command for callhome transport-email
Syntax:
Commoncommon
Command Mode: exec : Exec Mode
Command Path:
# show callhome common transport-email
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1329
S Commandsshow callhome common transport-email
show catalogshow catalog
Description: Show catalog information
Command Mode: exec : Exec Mode
Command Path:
# show catalog
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1330
S Commandsshow catalog
show cli commandshow cli command <WORD> [mode <mode-name>]
Description: Show Commands Syntax
Syntax:
Command Name pattern between single quotesWORD
(Optional) Mode name pattern between single quotes<mode-name>
(Optional) Show Command Detailsdetails
Command Mode: exec : Exec Mode
Command Path:
# show cli command <WORD> [mode <mode-name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1331
S Commandsshow cli command
show cli internal auditshow cli internal audit
Description: Show Commands Audit
Command Mode: exec : Exec Mode
Command Path:
# show cli internal audit
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1332
S Commandsshow cli internal audit
show cli internal transactionshow cli internal transaction logs|xml <NUMBER>
Description: Show Transaction Details
Syntax:
Show Transaction Logslogs
Show Transaction XML Postxml
Transaction ID(TID) to grep log lines with similar TIDs. TID can beextracted from the 'show cli internal audit' command. Number rangefrom=0 to=9223372036854775807
<Transaction ID>
Command Mode: exec : Exec Mode
Command Path:
# show cli internal transaction logs|xml <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1333
S Commandsshow cli internal transaction
show cli internal usageshow cli internal usage
Description: Show Commands with Usage Callback
Syntax:
(Optional) Show Command Detailsdetails
Command Mode: exec : Exec Mode
Command Path:
# show cli internal usage
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1334
S Commandsshow cli internal usage
show cli listshow cli list [mode <mode-name>]
Description: Show all cli-related commands
Syntax:
(Optional) Mode name pattern between single quotes<mode-name>
(Optional) Show Command Detailsdetails
Command Mode: exec : Exec Mode
Command Path:
# show cli list [mode <mode-name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1335
S Commandsshow cli list
show cli manpageshow cli manpage <WORD> [mode <mode-name>]
Description: Show Commands ManPage
Syntax:
Command Name pattern between single quotesWORD
(Optional) Mode name pattern between single quotes<mode-name>
(Optional) Show Command Detailsdetails
Command Mode: exec : Exec Mode
Command Path:
# show cli manpage <WORD> [mode <mode-name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1336
S Commandsshow cli manpage
show cli pathshow cli path <WORD> [mode <mode-name>]
Description: Show Commands Path
Syntax:
Command Name pattern between single quotesWORD
(Optional) Mode name pattern between single quotes<mode-name>
(Optional) Show Command Detailsdetails
Command Mode: exec : Exec Mode
Command Path:
# show cli path <WORD> [mode <mode-name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1337
S Commandsshow cli path
show clockshow clock
Description: Show clock information
Command Mode: exec : Exec Mode
Command Path:
# show clock
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1338
S Commandsshow clock
show communication ciphersshow communication ciphers
Description: HTTPS service cipher suite listings
Command Mode: exec : Exec Mode
Command Path:
# show communication ciphers
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1339
S Commandsshow communication ciphers
show communication controllershow communication controller node-id
Description: Show command for nginx web-requests
Syntax:
node-idnode-id
Command Mode: exec : Exec Mode
Command Path:
# show communication controller node-id
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1340
S Commandsshow communication controller
show communication httpshow communication http
Description: HTTP service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication http
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1341
S Commandsshow communication http
show communication httpsshow communication https
Description: HTTPS service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication https
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1342
S Commandsshow communication https
show communication shellinaboxshow communication shellinabox
Description: Shellinabox service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication shellinabox
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1343
S Commandsshow communication shellinabox
show communication ssh-serviceshow communication ssh-service
Description: SSH service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication ssh-service
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1344
S Commandsshow communication ssh-service
show communication telnetshow communication telnet
Description: Telnet service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication telnet
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1345
S Commandsshow communication telnet
show communication web-requestsshow communication web-requests
Description: Status of last web requests
Command Mode: exec : Exec Mode
Command Path:
# show communication web-requests
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1346
S Commandsshow communication web-requests
show contract-typeshow contract-type WORD
Description: Show Contracts Information Based on Type
Syntax:
whitelist (permit) or blacklist(deny) or oob-mgmt type of contractWORD
Command Mode: exec : Exec Mode
Command Path:
# show contract-type WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1347
S Commandsshow contract-type
show contractshow contract WORD
Description: Show Contracts Information
Syntax:
Name of the Contract to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show contract WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1348
S Commandsshow contract
show controllershow controller
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show controller
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1349
S Commandsshow controller
show controller detailshow controller detail [id <node-id>]
Description: Detailed controller information
Syntax:
(Optional) Optional Serial numbernode-id
Command Mode: exec : Exec Mode
Command Path:
# show controller detail [id <node-id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1350
S Commandsshow controller detail
show coresshow cores
Description: Show all core dumps
Command Mode: exec : Exec Mode
Command Path:
# show cores
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1351
S Commandsshow cores
show cores statusshow cores status
Description: Show exported core status
Command Mode: exec : Exec Mode
Command Path:
# show cores status
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1352
S Commandsshow cores status
show debug countershow debug <node-name> <process> counter <counterTopics>
Description: Show Counter information
Syntax:
Node name<node-name>
Process name<process>
Counter Topics<counterTopics>
Command Mode: exec : Exec Mode
Command Path:
# show debug <node-name> <process> counter <counterTopics>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1353
S Commandsshow debug counter
show debug logshow debug <node-name> <process> log
Description: Show log level information
Syntax:
Node name<node-name>
Process name<process>
Command Mode: exec : Exec Mode
Command Path:
# show debug <node-name> <process> log
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1354
S Commandsshow debug log
show deployment endpoint nodeshow deployment endpoint node <WORD>
Description: Node id
Syntax:
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Command Mode: exec : Exec Mode
Command Path:
# show deployment endpoint node <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1355
S Commandsshow deployment endpoint node
show dns-addressshow dns-address
Description: Show dns address information
Command Mode: exec : Exec Mode
Command Path:
# show dns-address
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1356
S Commandsshow dns-address
show dns-domainshow dns-domain
Description: Show dns domain information
Command Mode: exec : Exec Mode
Command Path:
# show dns-domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1357
S Commandsshow dns-domain
show dot1q-tunnelshow dot1q-tunnel WORD
Description: Show Dot1q-tunnel Information
Syntax:
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show dot1q-tunnel WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1358
S Commandsshow dot1q-tunnel
show endpointsshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints
Syntax:
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1359
S Commandsshow endpoints
show endpoints leaf interface ethernetshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface ethernet
Syntax:
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Ethernet Rangeethernet [<fex>/]<slot>/<port>
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet[<fex>/]<slot>/<port>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1360
S Commandsshow endpoints leaf interface ethernet
show endpoints leaf interface port-channelshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on an interface port-channel
Syntax:
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199<101-199>
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel<WORD> [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1361
S Commandsshow endpoints leaf interface port-channel
show endpoints vpcshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex<fex>]
Description: Show IP endpoints on vpc
Syntax:
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interfacevpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1362
S Commandsshow endpoints vpc
show epgshow epg WORD
Description: Show Application EPG Information
Syntax:
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1363
S Commandsshow epg
show epg detailshow epg WORD detail
Description: Show detailed view of Application EPg
Syntax:
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show epg WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1364
S Commandsshow epg detail
show eventsshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show event information
Syntax:
(Optional) Event code<event-code>
(Optional) Event ID<event-ID>
(Optional) Cause<event-value>
(Optional) Event activity in time interval. Number range from=1 to=59last-minutes <num-minutes>
(Optional) Event activity in time interval. Number range from=1 to=23last-hours <num-hours>
(Optional) Event activity in time interval. Number range from=1 to=999last-days <num-days>
(Optional) Event activity in time intervalstart-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Event activity in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Detailed event informationdetail
command scope<scope>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1365
S Commandsshow events
show events controllershow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1366
S Commandsshow events controller
show events controller detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]
Description: Detailed controller information
Syntax:
(Optional) Optional Serial numbernode-id
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1367
S Commandsshow events controller detail
show events leafshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>
Description: Show command for leaf
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1368
S Commandsshow events leaf
show events leaf fexshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum>
Description: Show extended chassis information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1369
S Commandsshow events leaf fex
show events leaf fex moduleshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum> module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1370
S Commandsshow events leaf fex module
show events leaf interface ethernetshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface ethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1371
S Commandsshow events leaf interface ethernet
show events leaf interface l3instanceshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface l3instance <l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1372
S Commandsshow events leaf interface l3instance
show events leaf interface mgmtshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface mgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1373
S Commandsshow events leaf interface mgmt
show events leaf interface portchannelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface portchannel <portChan>
Description: Port channel interface
Syntax:
Leaf id<leafId>
<Port channel number><portChan>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface portchannel <portChan>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1374
S Commandsshow events leaf interface portchannel
show events leaf interface tunnelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface tunnel <tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1375
S Commandsshow events leaf interface tunnel
show events leaf inventory chassisshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory chassis
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1376
S Commandsshow events leaf inventory chassis
show events leaf inventory fansshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory fans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1377
S Commandsshow events leaf inventory fans
show events leaf inventory moduleshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1378
S Commandsshow events leaf inventory module
show events leaf inventory module fabricportshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> fabricport<fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1379
S Commandsshow events leaf inventory module fabricport
show events leaf inventory module leafportshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> leafport <leafPort>
Description: Show information for leaf port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the leaf port number<leafPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> leafport<leafPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1380
S Commandsshow events leaf inventory module leafport
show events leaf inventory powersupplyshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory powersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1381
S Commandsshow events leaf inventory powersupply
show events leaf inventory supervisorshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory supervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1382
S Commandsshow events leaf inventory supervisor
show events leaf protocolshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol <protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1383
S Commandsshow events leaf protocol
show events leaf vpcshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc <vpcPort>
Description: Virtual port channel information
Syntax:
Leaf id<leafId>
pls enter virtual port channel number<vpcPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc <vpcPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1384
S Commandsshow events leaf vpc
show events leaf vrfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf <vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1385
S Commandsshow events leaf vrf
show events spineshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>
Description: Show command for spine
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1386
S Commandsshow events spine
show events spine interface ethernetshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface ethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1387
S Commandsshow events spine interface ethernet
show events spine interface l3instanceshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface l3instance <l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1388
S Commandsshow events spine interface l3instance
show events spine interface mgmtshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface mgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1389
S Commandsshow events spine interface mgmt
show events spine interface tunnelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface tunnel <tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1390
S Commandsshow events spine interface tunnel
show events spine inventory chassisshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory chassis
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1391
S Commandsshow events spine inventory chassis
show events spine inventory fabricshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fabric <fcMod>
Description: Show information for fabric module
Syntax:
Leaf id<leafId>
pls enter the fabric module number<fcMod>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fabric <fcMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1392
S Commandsshow events spine inventory fabric
show events spine inventory fansshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1393
S Commandsshow events spine inventory fans
show events spine inventory moduleshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1394
S Commandsshow events spine inventory module
show events spine inventory module fabricportshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>fabricport <fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1395
S Commandsshow events spine inventory module fabricport
show events spine inventory powersupplyshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory powersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1396
S Commandsshow events spine inventory powersupply
show events spine inventory supervisorshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory supervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1397
S Commandsshow events spine inventory supervisor
show events spine inventory systemshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory system <sysMod>
Description: Show information for system module
Syntax:
Leaf id<leafId>
pls enter the system module number<sysMod>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory system <sysMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1398
S Commandsshow events spine inventory system
show events spine protocolshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol <protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1399
S Commandsshow events spine protocol
show events spine vrfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf <vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1400
S Commandsshow events spine vrf
show events tenantshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1401
S Commandsshow events tenant
show events tenant applicationshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1402
S Commandsshow events tenant application
show events tenant application epgshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1403
S Commandsshow events tenant application epg
show events tenant bridge-domainshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1404
S Commandsshow events tenant bridge-domain
show events tenant bridge-domain detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1405
S Commandsshow events tenant bridge-domain detail
show events tenant bridge-domain first-hop-securitybinding-table
show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security binding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-securitybinding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1406
S Commandsshow events tenant bridge-domain first-hop-security binding-table
show events tenant bridge-domain first-hop-security statisticsarp
show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statistics arp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-securitystatistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1407
S Commandsshow events tenant bridge-domain first-hop-security statistics arp
show events tenant bridge-domain first-hop-security statisticsdhcpv4
show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statisticsdhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-securitystatistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1408
S Commandsshow events tenant bridge-domain first-hop-security statistics dhcpv4
show events tenant bridge-domain first-hop-security statisticsdhcpv6
show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statisticsdhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-securitystatistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1409
S Commandsshow events tenant bridge-domain first-hop-security statistics dhcpv6
show events tenant bridge-domain first-hop-security statisticsneighbor-discovery
show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statisticsneighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-securitystatistics neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1410
S Commandsshow events tenant bridge-domain first-hop-security statistics neighbor-discovery
show events tenant dnsservergroupshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD
Description: Show Dns Server Group Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1411
S Commandsshow events tenant dnsservergroup
show events tenant dnsservergroup servershow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD server WORD
Description: Show Dns Server Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD server WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1412
S Commandsshow events tenant dnsservergroup server
show events tenant dnsservergroup server domainshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD server WORD domain WORD
Description: Show Dns Domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Domain we eventually want to filter on (Max Size 512)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD server WORDdomain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1413
S Commandsshow events tenant dnsservergroup server domain
show events tenant endpointsshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1414
S Commandsshow events tenant endpoints
show events tenant endpoints leaf interface ethernetshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface ethernet
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Ethernet Rangeethernet [<fex>/]<slot>/<port>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1415
S Commandsshow events tenant endpoints leaf interface ethernet
show events tenant endpoints leaf interface port-channelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on an interface port-channel
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199<101-199>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1416
S Commandsshow events tenant endpoints leaf interface port-channel
show events tenant endpoints vpcshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]
Description: Show IP endpoints on vpc
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1417
S Commandsshow events tenant endpoints vpc
<A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1418
S Commandsshow events tenant endpoints vpc
show events tenant interface bridge-domainshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1419
S Commandsshow events tenant interface bridge-domain
show events tenant interface bridge-domain detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1420
S Commandsshow events tenant interface bridge-domain detail
show events tenant interface bridge-domain first-hop-securitybinding-table
show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitybinding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORDfirst-hop-security binding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1421
S Commandsshow events tenant interface bridge-domain first-hop-security binding-table
show events tenant interface bridge-domain first-hop-securitystatistics arp
show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics arp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORDfirst-hop-security statistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1422
S Commandsshow events tenant interface bridge-domain first-hop-security statistics arp
show events tenant interface bridge-domain first-hop-securitystatistics dhcpv4
show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics dhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORDfirst-hop-security statistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1423
S Commandsshow events tenant interface bridge-domain first-hop-security statistics dhcpv4
show events tenant interface bridge-domain first-hop-securitystatistics dhcpv6
show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics dhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORDfirst-hop-security statistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1424
S Commandsshow events tenant interface bridge-domain first-hop-security statistics dhcpv6
show events tenant interface bridge-domain first-hop-securitystatistics neighbor-discovery
show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics neighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORDfirst-hop-security statistics neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1425
S Commandsshow events tenant interface bridge-domain first-hop-security statistics neighbor-discovery
show events tenant multicast-route-mapsshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD multicast-route-maps
Description: Show multicast route-maps per Tenant
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD multicast-route-maps
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1426
S Commandsshow events tenant multicast-route-maps
show events tenant vrfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Description: Show VRF Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1427
S Commandsshow events tenant vrf
show events tenant vrf acllog l2show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD acllog <permitDrop> l2 flow vlan <NUMBER>srcintf <srcintf>
Description: L2 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flowi statsflow
vlan infovlan
<vlan>. Number range from=0 to=9223372036854775807<vlan>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD acllog <permitDrop> l2flow vlan <NUMBER> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1428
S Commandsshow events tenant vrf acllog l2
show events tenant vrf acllog l3show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD acllog <permitDrop> l3 flow srcip <A.B.C.Dor A:B::C:D> dstip <A.B.C.D or A:B::C:D> proto <proto> srcport <srcport> dstport <dstport> srcintf <srcintf>
Description: L3 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flow statsflow
source ipsrcip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
destination ipdstip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
protocolproto
<proto><proto>
source portsrcport
<srcport><srcport>
destination portdstport
<dstport><dstport>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD acllog <permitDrop> l3
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1429
S Commandsshow events tenant vrf acllog l3
flow srcip <A.B.C.D or A:B::C:D> dstip <A.B.C.D or A:B::C:D> proto <proto> srcport <srcport>dstport <dstport> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1430
S Commandsshow events tenant vrf acllog l3
show events tenant vrf detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1431
S Commandsshow events tenant vrf detail
show events tenant vrf external-l3 bgpshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Description: Show command for BGP peers
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1432
S Commandsshow events tenant vrf external-l3 bgp
show events tenant vrf external-l3 bgp nodeshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node<101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1433
S Commandsshow events tenant vrf external-l3 bgp node
show events tenant vrf external-l3 eigrpshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Description: Show external l3 EIGRP
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1434
S Commandsshow events tenant vrf external-l3 eigrp
show events tenant vrf external-l3 eigrp detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1435
S Commandsshow events tenant vrf external-l3 eigrp detail
show events tenant vrf external-l3 epgshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Description: Show command for external-l3 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1436
S Commandsshow events tenant vrf external-l3 epg
show events tenant vrf external-l3 epg detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1437
S Commandsshow events tenant vrf external-l3 epg detail
show events tenant vrf external-l3 epg nameshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: EPG name to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>name <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1438
S Commandsshow events tenant vrf external-l3 epg name
show events tenant vrf external-l3 epg name detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>name <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1439
S Commandsshow events tenant vrf external-l3 epg name detail
show events tenant vrf external-l3 interfacesshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1440
S Commandsshow events tenant vrf external-l3 interfaces
show events tenant vrf external-l3 interfaces detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show interfaces details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfacesdetail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1441
S Commandsshow events tenant vrf external-l3 interfaces detail
show events tenant vrf external-l3 ospfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Description: Show command for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1442
S Commandsshow events tenant vrf external-l3 ospf
show events tenant vrf external-l3 ospf detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Description: Show internal details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1443
S Commandsshow events tenant vrf external-l3 ospf detail
show events tenant vrf external-l3 route-mapshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name <l3out name>]
Description: Show command for external-l3 route-map
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
(Optional) Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name<l3out name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1444
S Commandsshow events tenant vrf external-l3 route-map
show events tenant vrf external-l3 route-map detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name <l3out name>]detail
Description: Show external-l3 route-map in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
(Optional) Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name<l3out name>] detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1445
S Commandsshow events tenant vrf external-l3 route-map detail
show events tenant vrf external-l3 static-routeshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Description: Show command for external-l3 static routes
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1446
S Commandsshow events tenant vrf external-l3 static-route
show events tenant vrf external-l3 static-route detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-routedetail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1447
S Commandsshow events tenant vrf external-l3 static-route detail
show events tenant vrf external-l3 static-route nodeshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-routenode
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1448
S Commandsshow events tenant vrf external-l3 static-route node
show events tenant vrf external-l3 static-route node detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-routenode detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1449
S Commandsshow events tenant vrf external-l3 static-route node detail
show events tenant vrf multicastshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD multicast
Description: Show multicast configuration per VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD multicast
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1450
S Commandsshow events tenant vrf multicast
show external-l2 epgshow external-l2 epg
Description: Show command for external-l2 epgs
Command Mode: exec : Exec Mode
Command Path:
# show external-l2 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1451
S Commandsshow external-l2 epg
show external-l2 epg nameshow external-l2 epg name WORD
Description: EPG name to filter on
Syntax:
Name of the EPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l2 epg name WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1452
S Commandsshow external-l2 epg name
show external-l2 epg tenantshow external-l2 epg tenant WORD
Description: tenant to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l2 epg tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1453
S Commandsshow external-l2 epg tenant
show external-l3 bgpshow external-l3 bgp
Description: Show command for BGP peers
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1454
S Commandsshow external-l3 bgp
show external-l3 bgp tenantshow external-l3 bgp tenant <WORD>
Description: tenant to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1455
S Commandsshow external-l3 bgp tenant
show external-l3 bgp tenant vrfshow external-l3 bgp tenant <WORD> vrf WORD
Description: vrf to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1456
S Commandsshow external-l3 bgp tenant vrf
show external-l3 bgp tenant vrf nodeshow external-l3 bgp tenant <WORD> vrf WORD node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp tenant <WORD> vrf WORD node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1457
S Commandsshow external-l3 bgp tenant vrf node
show external-l3 eigrpshow external-l3 eigrp
Description: Show command for external-l3 eigrp
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1458
S Commandsshow external-l3 eigrp
show external-l3 eigrp detailshow external-l3 eigrp detail
Description: Show interanl details
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1459
S Commandsshow external-l3 eigrp detail
show external-l3 eigrp nodeshow external-l3 eigrp node <101-4000>
Description: Node(s) to filter on
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1460
S Commandsshow external-l3 eigrp node
show external-l3 eigrp node detailshow external-l3 eigrp node <101-4000> detail
Description: Show interanl details
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1461
S Commandsshow external-l3 eigrp node detail
show external-l3 eigrp tenantshow external-l3 eigrp tenant <WORD>
Description: Tenant(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1462
S Commandsshow external-l3 eigrp tenant
show external-l3 eigrp tenant detailshow external-l3 eigrp tenant <WORD> detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1463
S Commandsshow external-l3 eigrp tenant detail
show external-l3 eigrp tenant vrfshow external-l3 eigrp tenant <WORD> vrf WORD
Description: Vrf(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1464
S Commandsshow external-l3 eigrp tenant vrf
show external-l3 eigrp tenant vrf detailshow external-l3 eigrp tenant <WORD> vrf WORD detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1465
S Commandsshow external-l3 eigrp tenant vrf detail
show external-l3 eigrp tenant vrf nodeshow external-l3 eigrp tenant <WORD> vrf WORD node <101-4000>
Description: Node(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1466
S Commandsshow external-l3 eigrp tenant vrf node
show external-l3 eigrp tenant vrf node detailshow external-l3 eigrp tenant <WORD> vrf WORD node <101-4000> detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1467
S Commandsshow external-l3 eigrp tenant vrf node detail
show external-l3 epgshow external-l3 epg
Description: Show command for external-l3 epgs
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1468
S Commandsshow external-l3 epg
show external-l3 epg detailshow external-l3 epg detail
Description: external-l3 epg in detail with operational status
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1469
S Commandsshow external-l3 epg detail
show external-l3 epg nameshow external-l3 epg name <epgName>
Description: EPG name to filter on
Syntax:
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg name <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1470
S Commandsshow external-l3 epg name
show external-l3 epg name detailshow external-l3 epg name <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg name <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1471
S Commandsshow external-l3 epg name detail
show external-l3 epg tenantshow external-l3 epg tenant <WORD>
Description: tenant to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1472
S Commandsshow external-l3 epg tenant
show external-l3 epg tenant detailshow external-l3 epg tenant <WORD> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1473
S Commandsshow external-l3 epg tenant detail
show external-l3 epg tenant vrfshow external-l3 epg tenant <WORD> vrf WORD
Description: vrf to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1474
S Commandsshow external-l3 epg tenant vrf
show external-l3 epg tenant vrf detailshow external-l3 epg tenant <WORD> vrf WORD detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1475
S Commandsshow external-l3 epg tenant vrf detail
show external-l3 interfacesshow external-l3 interfaces
Description: Show command for external-l3 interfaces
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1476
S Commandsshow external-l3 interfaces
show external-l3 interfaces detailshow external-l3 interfaces detail
Description: Show interfaces details
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1477
S Commandsshow external-l3 interfaces detail
show external-l3 interfaces nodeshow external-l3 interfaces node <101-4000>
Description: Node(s) to filter on
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1478
S Commandsshow external-l3 interfaces node
show external-l3 interfaces node detailshow external-l3 interfaces node <101-4000> detail
Description: Show interfaces details
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1479
S Commandsshow external-l3 interfaces node detail
show external-l3 interfaces tenantshow external-l3 interfaces tenant <WORD>
Description: Tenant(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1480
S Commandsshow external-l3 interfaces tenant
show external-l3 interfaces tenant detailshow external-l3 interfaces tenant <WORD> detail
Description: Show interfaces details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1481
S Commandsshow external-l3 interfaces tenant detail
show external-l3 interfaces tenant vrfshow external-l3 interfaces tenant <WORD> vrf WORD
Description: Vrf(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1482
S Commandsshow external-l3 interfaces tenant vrf
show external-l3 interfaces tenant vrf detailshow external-l3 interfaces tenant <WORD> vrf WORD detail
Description: Show interfaces details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1483
S Commandsshow external-l3 interfaces tenant vrf detail
show external-l3 interfaces tenant vrf nodeshow external-l3 interfaces tenant <WORD> vrf WORD node <101-4000>
Description: Node(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1484
S Commandsshow external-l3 interfaces tenant vrf node
show external-l3 interfaces tenant vrf node detailshow external-l3 interfaces tenant <WORD> vrf WORD node <101-4000> detail
Description: Show interfaces details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1485
S Commandsshow external-l3 interfaces tenant vrf node detail
show external-l3 ospfshow external-l3 ospf
Description: Show command for external-l3 ospf
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1486
S Commandsshow external-l3 ospf
show external-l3 ospf detailshow external-l3 ospf detail
Description: Show internal details
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1487
S Commandsshow external-l3 ospf detail
show external-l3 ospf nodeshow external-l3 ospf node <101-4000>
Description: Node(s) to filter on
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1488
S Commandsshow external-l3 ospf node
show external-l3 ospf node detailshow external-l3 ospf node <101-4000> detail
Description: Show internal details
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1489
S Commandsshow external-l3 ospf node detail
show external-l3 ospf tenantshow external-l3 ospf tenant <WORD>
Description: Tenant(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1490
S Commandsshow external-l3 ospf tenant
show external-l3 ospf tenant detailshow external-l3 ospf tenant <WORD> detail
Description: Show internal details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1491
S Commandsshow external-l3 ospf tenant detail
show external-l3 ospf tenant vrfshow external-l3 ospf tenant <WORD> vrf WORD
Description: Vrf(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1492
S Commandsshow external-l3 ospf tenant vrf
show external-l3 ospf tenant vrf detailshow external-l3 ospf tenant <WORD> vrf WORD detail
Description: Show internal details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1493
S Commandsshow external-l3 ospf tenant vrf detail
show external-l3 ospf tenant vrf nodeshow external-l3 ospf tenant <WORD> vrf WORD node <101-4000>
Description: Node(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1494
S Commandsshow external-l3 ospf tenant vrf node
show external-l3 ospf tenant vrf node detailshow external-l3 ospf tenant <WORD> vrf WORD node <101-4000> detail
Description: Show internal details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1495
S Commandsshow external-l3 ospf tenant vrf node detail
show external-l3 route-mapshow external-l3 route-map
Description: Show command for external-l3 route-map
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1496
S Commandsshow external-l3 route-map
show external-l3 route-map detailshow external-l3 route-map detail
Description: Route-map in detail with operational status
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1497
S Commandsshow external-l3 route-map detail
show external-l3 route-map nameshow external-l3 route-map name <l3out name>
Description: Route-map name to filter on
Syntax:
Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map name <l3out name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1498
S Commandsshow external-l3 route-map name
show external-l3 route-map name detailshow external-l3 route-map name <l3out name> detail
Description: Route-map in detail with operational status
Syntax:
Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map name <l3out name> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1499
S Commandsshow external-l3 route-map name detail
show external-l3 route-map tenantshow external-l3 route-map tenant <WORD>
Description: tenant to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1500
S Commandsshow external-l3 route-map tenant
show external-l3 route-map tenant detailshow external-l3 route-map tenant <WORD> detail
Description: Route-map in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1501
S Commandsshow external-l3 route-map tenant detail
show external-l3 route-map tenant vrfshow external-l3 route-map tenant <WORD> vrf WORD
Description: vrf to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1502
S Commandsshow external-l3 route-map tenant vrf
show external-l3 route-map tenant vrf detailshow external-l3 route-map tenant <WORD> vrf WORD detail
Description: Route-map in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1503
S Commandsshow external-l3 route-map tenant vrf detail
show external-l3 route-map tenant vrf nodeshow external-l3 route-map tenant <WORD> vrf WORD node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD node
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1504
S Commandsshow external-l3 route-map tenant vrf node
show external-l3 route-map tenant vrf node detailshow external-l3 route-map tenant <WORD> vrf WORD node detail
Description: Route-map in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1505
S Commandsshow external-l3 route-map tenant vrf node detail
show external-l3 static-routeshow external-l3 static-route
Description: Show command for external-l3 static routes
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1506
S Commandsshow external-l3 static-route
show external-l3 static-route detailshow external-l3 static-route detail
Description: static-route in detail with operational status
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1507
S Commandsshow external-l3 static-route detail
show external-l3 static-route nodeshow external-l3 static-route node
Description: node to filter on
Syntax:
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route node
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1508
S Commandsshow external-l3 static-route node
show external-l3 static-route node detailshow external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1509
S Commandsshow external-l3 static-route node detail
show external-l3 static-route tenantshow external-l3 static-route tenant <WORD>
Description: tenant to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1510
S Commandsshow external-l3 static-route tenant
show external-l3 static-route tenant detailshow external-l3 static-route tenant <WORD> detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1511
S Commandsshow external-l3 static-route tenant detail
show external-l3 static-route tenant vrfshow external-l3 static-route tenant <WORD> vrf WORD
Description: vrf to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1512
S Commandsshow external-l3 static-route tenant vrf
show external-l3 static-route tenant vrf detailshow external-l3 static-route tenant <WORD> vrf WORD detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1513
S Commandsshow external-l3 static-route tenant vrf detail
show external-l3 static-route tenant vrf nodeshow external-l3 static-route tenant <WORD> vrf WORD node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD node
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1514
S Commandsshow external-l3 static-route tenant vrf node
show external-l3 static-route tenant vrf node detailshow external-l3 static-route tenant <WORD> vrf WORD node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1515
S Commandsshow external-l3 static-route tenant vrf node detail
show fabric-recovery statusshow fabric-recovery status
Description: Show fabric recovery status
Command Mode: exec : Exec Mode
Command Path:
# show fabric-recovery status
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1516
S Commandsshow fabric-recovery status
show faultsshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes/no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show fault information
Syntax:
(Optional) Historical informationhistory
(Optional) Fault code<fault-code>
(Optional) Fault ID<fault-ID>
(Optional) Acknowledgment status<yes/no>
(Optional) Lifecycle state<lc-state>
(Optional) Severity<severity-value>
(Optional) Minimum severity<severity-value>
(Optional) Type<fault-type>
(Optional) Cause<fault-value>
(Optional) Fault activity in time interval. Number range from=1 to=59last-minutes <num-minutes>
(Optional) Fault activity in time interval. Number range from=1 to=23last-hours <num-hours>
(Optional) Fault activity in time interval. Number range from=1 to=999last-days <num-days>
(Optional) Fault activity in time intervalstart-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Fault activity in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Detailed faults informationdetail
command scope<scope>
Command Mode: exec : Exec Mode
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1517
S Commandsshow faults
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes/no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-timestart-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]<scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1518
S Commandsshow faults
show faults controllershow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1519
S Commandsshow faults controller
show faults controller detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]
Description: Detailed controller information
Syntax:
(Optional) Optional Serial numbernode-id
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id<node-id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1520
S Commandsshow faults controller detail
show faults l4l7-clustershow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]
Description: Show L4 L7 Device information
Syntax:
(Optional) Name of TenantTenant Name
(Optional) Name of DeviceDevice Cluster Name
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-cluster [tenant<Tenant Name>] [cluster <Device Cluster Name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1521
S Commandsshow faults l4l7-cluster
show faults l4l7-graphshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]
Description: Show L4 L7 Graph information
Syntax:
(Optional) Name of Tenant<Tenant Name>
(Optional) Name of Graph<Graph Name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-graph [tenant<Tenant Name>] [graph <Graph Name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1522
S Commandsshow faults l4l7-graph
show faults leafshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>
Description: Show command for leaf
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1523
S Commandsshow faults leaf
show faults leaf fexshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum>
Description: Show extended chassis information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex<fexNum>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1524
S Commandsshow faults leaf fex
show faults leaf fex moduleshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex<fexNum> module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1525
S Commandsshow faults leaf fex module
show faults leaf interface ethernetshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfaceethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1526
S Commandsshow faults leaf interface ethernet
show faults leaf interface l3instanceshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfacel3instance <l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1527
S Commandsshow faults leaf interface l3instance
show faults leaf interface mgmtshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfacemgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1528
S Commandsshow faults leaf interface mgmt
show faults leaf interface portchannelshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface portchannel <portChan>
Description: Port channel interface
Syntax:
Leaf id<leafId>
<Port channel number><portChan>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfaceportchannel <portChan>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1529
S Commandsshow faults leaf interface portchannel
show faults leaf interface tunnelshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfacetunnel <tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1530
S Commandsshow faults leaf interface tunnel
show faults leaf inventory chassisshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorychassis
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1531
S Commandsshow faults leaf inventory chassis
show faults leaf inventory fansshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventoryfans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1532
S Commandsshow faults leaf inventory fans
show faults leaf inventory moduleshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorymodule <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1533
S Commandsshow faults leaf inventory module
show faults leaf inventory module fabricportshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorymodule <lcSlot> fabricport <fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1534
S Commandsshow faults leaf inventory module fabricport
show faults leaf inventory module leafportshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> leafport <leafPort>
Description: Show information for leaf port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the leaf port number<leafPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorymodule <lcSlot> leafport <leafPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1535
S Commandsshow faults leaf inventory module leafport
show faults leaf inventory powersupplyshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1536
S Commandsshow faults leaf inventory powersupply
show faults leaf inventory supervisorshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorysupervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1537
S Commandsshow faults leaf inventory supervisor
show faults leaf protocolshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol<protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1538
S Commandsshow faults leaf protocol
show faults leaf vpcshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc <vpcPort>
Description: Virtual port channel information
Syntax:
Leaf id<leafId>
pls enter virtual port channel number<vpcPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc<vpcPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1539
S Commandsshow faults leaf vpc
show faults leaf vrfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf<vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1540
S Commandsshow faults leaf vrf
show faults microsoft domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain
Description: Show Microsoft domain information
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1541
S Commandsshow faults microsoft domain
show faults microsoft domain nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD>
Description:Microsoft domain name
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1542
S Commandsshow faults microsoft domain name
show faults microsoft domain name hypervshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> hyperv <WORD>
Description: Show Microsoft Hypervisor information
Syntax:
Microsoft domain nameWORD
HyperV hostnameWORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> hyperv <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1543
S Commandsshow faults microsoft domain name hyperv
show faults microsoft domain name port-groupshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> port-group
Description: Show Microsoft port group information
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> port-group
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1544
S Commandsshow faults microsoft domain name port-group
show faults microsoft domain name scvmmshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> scvmm <hostname|ip>
Description: Show Microsoft SCVMM information
Syntax:
Microsoft domain nameWORD
SCVMM hostname or IP<hostname|ip>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> scvmm <hostname|ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1545
S Commandsshow faults microsoft domain name scvmm
show faults microsoft domain name vmshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> vm
Description: Show Microsoft VM information
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> vm
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1546
S Commandsshow faults microsoft domain name vm
show faults microsoft domain name vm nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> vm name <WORD>
Description: Show detailed Microsoft VM information
Syntax:
Microsoft domain nameWORD
VM NameWORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> vm name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1547
S Commandsshow faults microsoft domain name vm name
show faults quotashow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] quota
Description: Show Quotas Information
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] quota
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1548
S Commandsshow faults quota
show faults spineshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>
Description: Show command for spine
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1549
S Commandsshow faults spine
show faults spine interface ethernetshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfaceethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1550
S Commandsshow faults spine interface ethernet
show faults spine interface l3instanceshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfacel3instance <l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1551
S Commandsshow faults spine interface l3instance
show faults spine interface mgmtshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfacemgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1552
S Commandsshow faults spine interface mgmt
show faults spine interface tunnelshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfacetunnel <tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1553
S Commandsshow faults spine interface tunnel
show faults spine inventory chassisshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorychassis
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1554
S Commandsshow faults spine inventory chassis
show faults spine inventory fabricshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fabric <fcMod>
Description: Show information for fabric module
Syntax:
Leaf id<leafId>
pls enter the fabric module number<fcMod>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventoryfabric <fcMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1555
S Commandsshow faults spine inventory fabric
show faults spine inventory fansshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventoryfans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1556
S Commandsshow faults spine inventory fans
show faults spine inventory moduleshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorymodule <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1557
S Commandsshow faults spine inventory module
show faults spine inventory module fabricportshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorymodule <lcSlot> fabricport <fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1558
S Commandsshow faults spine inventory module fabricport
show faults spine inventory powersupplyshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1559
S Commandsshow faults spine inventory powersupply
show faults spine inventory supervisorshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorysupervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1560
S Commandsshow faults spine inventory supervisor
show faults spine inventory systemshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory system <sysMod>
Description: Show information for system module
Syntax:
Leaf id<leafId>
pls enter the system module number<sysMod>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorysystem <sysMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1561
S Commandsshow faults spine inventory system
show faults spine protocolshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol<protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1562
S Commandsshow faults spine protocol
show faults spine vrfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf<vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1563
S Commandsshow faults spine vrf
show faults tenantshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1564
S Commandsshow faults tenant
show faults tenant applicationshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD applicationWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1565
S Commandsshow faults tenant application
show faults tenant application epgshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD applicationWORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1566
S Commandsshow faults tenant application epg
show faults tenant bridge-domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDbridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1567
S Commandsshow faults tenant bridge-domain
show faults tenant bridge-domain detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDbridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1568
S Commandsshow faults tenant bridge-domain detail
show faults tenant bridge-domain first-hop-securitybinding-table
show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security binding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDbridge-domain WORD first-hop-security binding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1569
S Commandsshow faults tenant bridge-domain first-hop-security binding-table
show faults tenant bridge-domain first-hop-security statisticsarp
show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statistics arp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDbridge-domain WORD first-hop-security statistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1570
S Commandsshow faults tenant bridge-domain first-hop-security statistics arp
show faults tenant bridge-domain first-hop-security statisticsdhcpv4
show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statisticsdhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDbridge-domain WORD first-hop-security statistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1571
S Commandsshow faults tenant bridge-domain first-hop-security statistics dhcpv4
show faults tenant bridge-domain first-hop-security statisticsdhcpv6
show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statisticsdhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDbridge-domain WORD first-hop-security statistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1572
S Commandsshow faults tenant bridge-domain first-hop-security statistics dhcpv6
show faults tenant bridge-domain first-hop-security statisticsneighbor-discovery
show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD first-hop-security statisticsneighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDbridge-domain WORD first-hop-security statistics neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1573
S Commandsshow faults tenant bridge-domain first-hop-security statistics neighbor-discovery
show faults tenant dnsservergroupshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD
Description: Show Dns Server Group Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDdnsservergroup WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1574
S Commandsshow faults tenant dnsservergroup
show faults tenant dnsservergroup servershow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD server WORD
Description: Show Dns Server Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDdnsservergroup WORD server WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1575
S Commandsshow faults tenant dnsservergroup server
show faults tenant dnsservergroup server domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD dnsservergroup WORD server WORD domain WORD
Description: Show Dns Domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Domain we eventually want to filter on (Max Size 512)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDdnsservergroup WORD server WORD domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1576
S Commandsshow faults tenant dnsservergroup server domain
show faults tenant interface bridge-domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interfacebridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1577
S Commandsshow faults tenant interface bridge-domain
show faults tenant interface bridge-domain detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interfacebridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1578
S Commandsshow faults tenant interface bridge-domain detail
show faults tenant interface bridge-domain first-hop-securitybinding-table
show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitybinding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interfacebridge-domain WORD first-hop-security binding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1579
S Commandsshow faults tenant interface bridge-domain first-hop-security binding-table
show faults tenant interface bridge-domain first-hop-securitystatistics arp
show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics arp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interfacebridge-domain WORD first-hop-security statistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1580
S Commandsshow faults tenant interface bridge-domain first-hop-security statistics arp
show faults tenant interface bridge-domain first-hop-securitystatistics dhcpv4
show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics dhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interfacebridge-domain WORD first-hop-security statistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1581
S Commandsshow faults tenant interface bridge-domain first-hop-security statistics dhcpv4
show faults tenant interface bridge-domain first-hop-securitystatistics dhcpv6
show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics dhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interfacebridge-domain WORD first-hop-security statistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1582
S Commandsshow faults tenant interface bridge-domain first-hop-security statistics dhcpv6
show faults tenant interface bridge-domain first-hop-securitystatistics neighbor-discovery
show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD first-hop-securitystatistics neighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interfacebridge-domain WORD first-hop-security statistics neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1583
S Commandsshow faults tenant interface bridge-domain first-hop-security statistics neighbor-discovery
show faults tenant multicast-route-mapsshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD multicast-route-maps
Description: Show multicast route-maps per Tenant
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDmulticast-route-maps
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1584
S Commandsshow faults tenant multicast-route-maps
show faults tenant vrfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Description: Show VRF Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1585
S Commandsshow faults tenant vrf
show faults tenant vrf acllog l2show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD acllog <permitDrop> l2 flow vlan <NUMBER>srcintf <srcintf>
Description: L2 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flowi statsflow
vlan infovlan
<vlan>. Number range from=0 to=9223372036854775807<vlan>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDacllog <permitDrop> l2 flow vlan <NUMBER> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1586
S Commandsshow faults tenant vrf acllog l2
show faults tenant vrf acllog l3show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD acllog <permitDrop> l3 flow srcip <A.B.C.Dor A:B::C:D> dstip <A.B.C.D or A:B::C:D> proto <proto> srcport <srcport> dstport <dstport> srcintf <srcintf>
Description: L3 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flow statsflow
source ipsrcip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
destination ipdstip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
protocolproto
<proto><proto>
source portsrcport
<srcport><srcport>
destination portdstport
<dstport><dstport>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1587
S Commandsshow faults tenant vrf acllog l3
[severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDacllog <permitDrop> l3 flow srcip <A.B.C.D or A:B::C:D> dstip <A.B.C.D or A:B::C:D> proto<proto> srcport <srcport> dstport <dstport> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1588
S Commandsshow faults tenant vrf acllog l3
show faults tenant vrf detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDdetail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1589
S Commandsshow faults tenant vrf detail
show faults tenant vrf external-l3 bgpshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Description: Show command for BGP peers
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1590
S Commandsshow faults tenant vrf external-l3 bgp
show faults tenant vrf external-l3 bgp nodeshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 bgp node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1591
S Commandsshow faults tenant vrf external-l3 bgp node
show faults tenant vrf external-l3 eigrpshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Description: Show external l3 EIGRP
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1592
S Commandsshow faults tenant vrf external-l3 eigrp
show faults tenant vrf external-l3 eigrp detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1593
S Commandsshow faults tenant vrf external-l3 eigrp detail
show faults tenant vrf external-l3 epgshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Description: Show command for external-l3 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1594
S Commandsshow faults tenant vrf external-l3 epg
show faults tenant vrf external-l3 epg detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1595
S Commandsshow faults tenant vrf external-l3 epg detail
show faults tenant vrf external-l3 epg nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: EPG name to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName> name <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1596
S Commandsshow faults tenant vrf external-l3 epg name
show faults tenant vrf external-l3 epg name detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName> name <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1597
S Commandsshow faults tenant vrf external-l3 epg name detail
show faults tenant vrf external-l3 interfacesshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1598
S Commandsshow faults tenant vrf external-l3 interfaces
show faults tenant vrf external-l3 interfaces detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show interfaces details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 interfaces detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1599
S Commandsshow faults tenant vrf external-l3 interfaces detail
show faults tenant vrf external-l3 ospfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Description: Show command for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1600
S Commandsshow faults tenant vrf external-l3 ospf
show faults tenant vrf external-l3 ospf detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Description: Show internal details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1601
S Commandsshow faults tenant vrf external-l3 ospf detail
show faults tenant vrf external-l3 static-routeshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Description: Show command for external-l3 static routes
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1602
S Commandsshow faults tenant vrf external-l3 static-route
show faults tenant vrf external-l3 static-route detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1603
S Commandsshow faults tenant vrf external-l3 static-route detail
show faults tenant vrf external-l3 static-route nodeshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route node
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1604
S Commandsshow faults tenant vrf external-l3 static-route node
show faults tenant vrf external-l3 static-route node detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1605
S Commandsshow faults tenant vrf external-l3 static-route node detail
show faults tenant vrf multicastshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD multicast
Description: Show multicast configuration per VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDmulticast
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1606
S Commandsshow faults tenant vrf multicast
show faults vmware domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain
Description: Show VMware domain information
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1607
S Commandsshow faults vmware domain
show faults vmware domain nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name>
Description: VMware domain name
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1608
S Commandsshow faults vmware domain name
show faults vmware domain name epgshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> epg
Description: Show VMware domain EPG details
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> epg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1609
S Commandsshow faults vmware domain name epg
show faults vmware domain name esxshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> esx <esx-ip>
Description: Show VMware ESX information
Syntax:
VMware domain name<name>
ESX IP<esx-ip>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> esx <esx-ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1610
S Commandsshow faults vmware domain name esx
show faults vmware domain name port-groupshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> port-group
Description: Show VMware port group information
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> port-group
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1611
S Commandsshow faults vmware domain name port-group
show faults vmware domain name trunk-portgroupshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> trunk-portgroup [name <name>]
Description: Show VMware domain trunk portgroup details
Syntax:
VMware domain name<name>
(Optional) trunk portgroup name<name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> trunk-portgroup [name <name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1612
S Commandsshow faults vmware domain name trunk-portgroup
show faults vmware domain name vcentershow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vcenter <hostname|ip>
Description: VMware vCenter ip or hostname
Syntax:
VMware domain name<name>
vCenter hostname or IP<hostname|ip>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> vcenter <hostname|ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1613
S Commandsshow faults vmware domain name vcenter
show faults vmware domain name vmshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vm
Description: Show VMware VM information
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> vm
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1614
S Commandsshow faults vmware domain name vm
show faults vmware domain name vm nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vm name <vm-name>
Description: Show detailed VMware VM information
Syntax:
VMware domain name<name>
VM Name<vm-name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> vm name <vm-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1615
S Commandsshow faults vmware domain name vm name
show fipsshow fips
Description: Show FIPS information
Command Mode: exec : Exec Mode
Command Path:
# show fips
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1616
S Commandsshow fips
show fips statusshow fips status
Description: Show FIPS status
Command Mode: exec : Exec Mode
Command Path:
# show fips status
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1617
S Commandsshow fips status
show firmware repositoryshow firmware repository
Description: Show firmware images present in repository
Command Mode: exec : Exec Mode
Command Path:
# show firmware repository
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1618
S Commandsshow firmware repository
show firmware repository detailshow firmware repository detail
Description: Detailed repository information
Command Mode: exec : Exec Mode
Command Path:
# show firmware repository detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1619
S Commandsshow firmware repository detail
show firmware upgrade statusshow firmware upgrade status
Description: Upgrade status of all controllers and switches
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1620
S Commandsshow firmware upgrade status
show firmware upgrade status controller-groupshow firmware upgrade status controller-group
Description: Controller-group upgrade status
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status controller-group
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1621
S Commandsshow firmware upgrade status controller-group
show firmware upgrade status controller-group detailshow firmware upgrade status controller-group detail
Description: Detailed upgrade status
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status controller-group detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1622
S Commandsshow firmware upgrade status controller-group detail
show firmware upgrade status detailshow firmware upgrade status detail
Description: Detailed upgrade status information
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1623
S Commandsshow firmware upgrade status detail
show firmware upgrade status switch-groupshow firmware upgrade status switch-group <WORD>
Description: Switch-group upgrade status
Syntax:
switch-group name (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status switch-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1624
S Commandsshow firmware upgrade status switch-group
show firmware upgrade status switch-group detailshow firmware upgrade status switch-group <WORD> detail
Description: Detailed upgrade status
Syntax:
switch-group name (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status switch-group <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1625
S Commandsshow firmware upgrade status switch-group detail
show flow exportershow flow exporter
Description: Show Netflow exporter information
Command Mode: exec : Exec Mode
Command Path:
# show flow exporter
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1626
S Commandsshow flow exporter
show flow exporter infrashow flow exporter infra WORD [detail]
Description: Show flow exporter infra information
Syntax:
Exporter NameWORD
(Optional) detaildetail
Command Mode: exec : Exec Mode
Command Path:
# show flow exporter infra WORD [detail]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1627
S Commandsshow flow exporter infra
show flow exporter tenantshow flow exporter tenant <WORD> WORD [detail]
Description: Show flow exporter tenant information
Syntax:
Optional tenant nameWORD
Exporter NameWORD
(Optional) detaildetail
Command Mode: exec : Exec Mode
Command Path:
# show flow exporter tenant <WORD> WORD [detail]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1628
S Commandsshow flow exporter tenant
show flow monitorshow flow monitor
Description: Show Netflow Monitor Information
Command Mode: exec : Exec Mode
Command Path:
# show flow monitor
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1629
S Commandsshow flow monitor
show flow monitor infrashow flow monitor infra WORD [detail]
Description: Show Netflow Monitor Information for infra
Syntax:
Optional Monitor NameWORD
(Optional) detaildetail
Command Mode: exec : Exec Mode
Command Path:
# show flow monitor infra WORD [detail]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1630
S Commandsshow flow monitor infra
show flow monitor tenantshow flow monitor tenant <WORD> WORD [detail]
Description: Show Netflow Monitor Information for the specified tenant
Syntax:
Specify tenant nameWORD
Optional Monitor NameWORD
(Optional) detaildetail
Command Mode: exec : Exec Mode
Command Path:
# show flow monitor tenant <WORD> WORD [detail]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1631
S Commandsshow flow monitor tenant
show flow node-policyshow flow node-policy [name <WORD>]
Description: Show Netflow Node Policy Information
Syntax:
(Optional) Optional Node Policy NameWORD
Command Mode: exec : Exec Mode
Command Path:
# show flow node-policy [name <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1632
S Commandsshow flow node-policy
show flow node-policy detailshow flow node-policy [name <WORD>] detail
Description: Show Netflow Node Policy Detailed Information
Syntax:
(Optional) Optional Node Policy NameWORD
Command Mode: exec : Exec Mode
Command Path:
# show flow node-policy [name <WORD>] detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1633
S Commandsshow flow node-policy detail
show flow recordshow flow record
Description: Show Netflow record information
Command Mode: exec : Exec Mode
Command Path:
# show flow record
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1634
S Commandsshow flow record
show flow record infrashow flow record infra WORD [detail]
Description: Show flow record infra information
Syntax:
Record NameWORD
(Optional) detaildetail
Command Mode: exec : Exec Mode
Command Path:
# show flow record infra WORD [detail]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1635
S Commandsshow flow record infra
show flow record tenantshow flow record tenant [record-name <recordName>] <tenantName> WORD [detail]
Description: Show flow record tenant information
Syntax:
(Optional) Optional record namerecordName
Optional tenant nametenantName
Record NameWORD
(Optional) detaildetail
Command Mode: exec : Exec Mode
Command Path:
# show flow record tenant [record-name <recordName>] <tenantName> WORD [detail]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1636
S Commandsshow flow record tenant
show flow vm-exportershow flow vm-exporter WORD
Description: Show NetFlow Exporter information for VM Networking
Syntax:
NetFlow Exporter NameWORD
Command Mode: exec : Exec Mode
Command Path:
# show flow vm-exporter WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1637
S Commandsshow flow vm-exporter
show healthshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] <scope>
Description: Show health score information
Syntax:
(Optional) Historical informationhistory
(Optional) Minimum change in health score percentage. Number rangefrom=-100 to=9999
min-change <percentage change>
(Optional) Maximum health score. Number range from=0 to=100max-hs <maximum health-score>
(Optional) Health activity in time intervalstart-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Health activity in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>
command scope<scope>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1638
S Commandsshow health
show health leafshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId>
Description: Show command for leaf
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1639
S Commandsshow health leaf
show health leaf fexshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum>
Description: Show extended chassis information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1640
S Commandsshow health leaf fex
show health leaf fex moduleshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum>module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1641
S Commandsshow health leaf fex module
show health leaf interface ethernetshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface ethernet<phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1642
S Commandsshow health leaf interface ethernet
show health leaf interface l3instanceshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface l3instance<l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1643
S Commandsshow health leaf interface l3instance
show health leaf interface mgmtshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface mgmt<mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1644
S Commandsshow health leaf interface mgmt
show health leaf interface portchannelshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface portchannel <portChan>
Description: Port channel interface
Syntax:
Leaf id<leafId>
<Port channel number><portChan>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interfaceportchannel <portChan>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1645
S Commandsshow health leaf interface portchannel
show health leaf interface tunnelshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface tunnel<tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1646
S Commandsshow health leaf interface tunnel
show health leaf inventory chassisshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory chassis
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1647
S Commandsshow health leaf inventory chassis
show health leaf inventory fansshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory fans<ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1648
S Commandsshow health leaf inventory fans
show health leaf inventory moduleshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module<lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1649
S Commandsshow health leaf inventory module
show health leaf inventory module fabricportshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module<lcSlot> fabricport <fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1650
S Commandsshow health leaf inventory module fabricport
show health leaf inventory module leafportshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot> leafport <leafPort>
Description: Show information for leaf port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the leaf port number<leafPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module<lcSlot> leafport <leafPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1651
S Commandsshow health leaf inventory module leafport
show health leaf inventory powersupplyshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1652
S Commandsshow health leaf inventory powersupply
show health leaf inventory supervisorshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory supervisor<supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1653
S Commandsshow health leaf inventory supervisor
show health leaf protocolshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> protocol <protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1654
S Commandsshow health leaf protocol
show health leaf vpcshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vpc <vpcPort>
Description: Virtual port channel information
Syntax:
Leaf id<leafId>
pls enter virtual port channel number<vpcPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vpc <vpcPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1655
S Commandsshow health leaf vpc
show health leaf vrfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vrf <vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1656
S Commandsshow health leaf vrf
show health spineshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId>
Description: Show command for spine
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1657
S Commandsshow health spine
show health spine interface ethernetshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface ethernet<phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1658
S Commandsshow health spine interface ethernet
show health spine interface l3instanceshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interfacel3instance <l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1659
S Commandsshow health spine interface l3instance
show health spine interface mgmtshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface mgmt<mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1660
S Commandsshow health spine interface mgmt
show health spine interface tunnelshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface tunnel<tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1661
S Commandsshow health spine interface tunnel
show health spine inventory chassisshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory chassis
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1662
S Commandsshow health spine inventory chassis
show health spine inventory fabricshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fabric <fcMod>
Description: Show information for fabric module
Syntax:
Leaf id<leafId>
pls enter the fabric module number<fcMod>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fabric<fcMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1663
S Commandsshow health spine inventory fabric
show health spine inventory fansshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fans<ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1664
S Commandsshow health spine inventory fans
show health spine inventory moduleshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module<lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1665
S Commandsshow health spine inventory module
show health spine inventory module fabricportshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module<lcSlot> fabricport <fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1666
S Commandsshow health spine inventory module fabricport
show health spine inventory powersupplyshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1667
S Commandsshow health spine inventory powersupply
show health spine inventory supervisorshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventorysupervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1668
S Commandsshow health spine inventory supervisor
show health spine inventory systemshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory system <sysMod>
Description: Show information for system module
Syntax:
Leaf id<leafId>
pls enter the system module number<sysMod>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory system<sysMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1669
S Commandsshow health spine inventory system
show health spine protocolshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> protocol <protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1670
S Commandsshow health spine protocol
show health spine vrfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> vrf <vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1671
S Commandsshow health spine vrf
show health tenantshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1672
S Commandsshow health tenant
show health tenant applicationshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1673
S Commandsshow health tenant application
show health tenant application epgshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORDepg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1674
S Commandsshow health tenant application epg
show health tenant bridge-domainshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1675
S Commandsshow health tenant bridge-domain
show health tenant bridge-domain detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORDdetail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1676
S Commandsshow health tenant bridge-domain detail
show health tenant bridge-domain first-hop-securitybinding-table
show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD first-hop-security binding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORDfirst-hop-security binding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1677
S Commandsshow health tenant bridge-domain first-hop-security binding-table
show health tenant bridge-domain first-hop-security statisticsarp
show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD first-hop-security statisticsarp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORDfirst-hop-security statistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1678
S Commandsshow health tenant bridge-domain first-hop-security statistics arp
show health tenant bridge-domain first-hop-security statisticsdhcpv4
show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD first-hop-security statisticsdhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORDfirst-hop-security statistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1679
S Commandsshow health tenant bridge-domain first-hop-security statistics dhcpv4
show health tenant bridge-domain first-hop-security statisticsdhcpv6
show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD first-hop-security statisticsdhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORDfirst-hop-security statistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1680
S Commandsshow health tenant bridge-domain first-hop-security statistics dhcpv6
show health tenant bridge-domain first-hop-security statisticsneighbor-discovery
show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD first-hop-security statisticsneighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORDfirst-hop-security statistics neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1681
S Commandsshow health tenant bridge-domain first-hop-security statistics neighbor-discovery
show health tenant dnsservergroupshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD dnsservergroup WORD
Description: Show Dns Server Group Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD dnsservergroup WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1682
S Commandsshow health tenant dnsservergroup
show health tenant dnsservergroup servershow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD dnsservergroup WORD server WORD
Description: Show Dns Server Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD dnsservergroup WORDserver WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1683
S Commandsshow health tenant dnsservergroup server
show health tenant dnsservergroup server domainshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD dnsservergroup WORD server WORD domain WORD
Description: Show Dns Domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Domain we eventually want to filter on (Max Size 512)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD dnsservergroup WORDserver WORD domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1684
S Commandsshow health tenant dnsservergroup server domain
show health tenant interface bridge-domainshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interfacebridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1685
S Commandsshow health tenant interface bridge-domain
show health tenant interface bridge-domain detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interfacebridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1686
S Commandsshow health tenant interface bridge-domain detail
show health tenant interface bridge-domain first-hop-securitybinding-table
show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD first-hop-securitybinding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interfacebridge-domain WORD first-hop-security binding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1687
S Commandsshow health tenant interface bridge-domain first-hop-security binding-table
show health tenant interface bridge-domain first-hop-securitystatistics arp
show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD first-hop-securitystatistics arp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interfacebridge-domain WORD first-hop-security statistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1688
S Commandsshow health tenant interface bridge-domain first-hop-security statistics arp
show health tenant interface bridge-domain first-hop-securitystatistics dhcpv4
show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD first-hop-securitystatistics dhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interfacebridge-domain WORD first-hop-security statistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1689
S Commandsshow health tenant interface bridge-domain first-hop-security statistics dhcpv4
show health tenant interface bridge-domain first-hop-securitystatistics dhcpv6
show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD first-hop-securitystatistics dhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interfacebridge-domain WORD first-hop-security statistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1690
S Commandsshow health tenant interface bridge-domain first-hop-security statistics dhcpv6
show health tenant interface bridge-domain first-hop-securitystatistics neighbor-discovery
show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD first-hop-securitystatistics neighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interfacebridge-domain WORD first-hop-security statistics neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1691
S Commandsshow health tenant interface bridge-domain first-hop-security statistics neighbor-discovery
show health tenant multicast-route-mapsshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD multicast-route-maps
Description: Show multicast route-maps per Tenant
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD multicast-route-maps
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1692
S Commandsshow health tenant multicast-route-maps
show health tenant vrfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD
Description: Show VRF Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1693
S Commandsshow health tenant vrf
show health tenant vrf acllog l2show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD acllog <permitDrop> l2 flow vlan <NUMBER>srcintf <srcintf>
Description: L2 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flowi statsflow
vlan infovlan
<vlan>. Number range from=0 to=9223372036854775807<vlan>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD acllog<permitDrop> l2 flow vlan <NUMBER> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1694
S Commandsshow health tenant vrf acllog l2
show health tenant vrf acllog l3show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD acllog <permitDrop> l3 flow srcip <A.B.C.Dor A:B::C:D> dstip <A.B.C.D or A:B::C:D> proto <proto> srcport <srcport> dstport <dstport> srcintf <srcintf>
Description: L3 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flow statsflow
source ipsrcip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
destination ipdstip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
protocolproto
<proto><proto>
source portsrcport
<srcport><srcport>
destination portdstport
<dstport><dstport>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD acllog<permitDrop> l3 flow srcip <A.B.C.D or A:B::C:D> dstip <A.B.C.D or A:B::C:D> proto <proto>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1695
S Commandsshow health tenant vrf acllog l3
srcport <srcport> dstport <dstport> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1696
S Commandsshow health tenant vrf acllog l3
show health tenant vrf detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1697
S Commandsshow health tenant vrf detail
show health tenant vrf external-l3 bgpshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 bgp
Description: Show command for BGP peers
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1698
S Commandsshow health tenant vrf external-l3 bgp
show health tenant vrf external-l3 bgp nodeshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3bgp node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1699
S Commandsshow health tenant vrf external-l3 bgp node
show health tenant vrf external-l3 eigrpshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 eigrp
Description: Show external l3 EIGRP
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1700
S Commandsshow health tenant vrf external-l3 eigrp
show health tenant vrf external-l3 eigrp detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1701
S Commandsshow health tenant vrf external-l3 eigrp detail
show health tenant vrf external-l3 epgshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName>
Description: Show command for external-l3 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1702
S Commandsshow health tenant vrf external-l3 epg
show health tenant vrf external-l3 epg detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1703
S Commandsshow health tenant vrf external-l3 epg detail
show health tenant vrf external-l3 epg nameshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName>
Description: EPG name to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName> name <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1704
S Commandsshow health tenant vrf external-l3 epg name
show health tenant vrf external-l3 epg name detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName> name <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1705
S Commandsshow health tenant vrf external-l3 epg name detail
show health tenant vrf external-l3 interfacesshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 interfaces
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1706
S Commandsshow health tenant vrf external-l3 interfaces
show health tenant vrf external-l3 interfaces detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show interfaces details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3interfaces detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1707
S Commandsshow health tenant vrf external-l3 interfaces detail
show health tenant vrf external-l3 ospfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 ospf
Description: Show command for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1708
S Commandsshow health tenant vrf external-l3 ospf
show health tenant vrf external-l3 ospf detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 ospf detail
Description: Show internal details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1709
S Commandsshow health tenant vrf external-l3 ospf detail
show health tenant vrf external-l3 static-routeshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route
Description: Show command for external-l3 static routes
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1710
S Commandsshow health tenant vrf external-l3 static-route
show health tenant vrf external-l3 static-route detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1711
S Commandsshow health tenant vrf external-l3 static-route detail
show health tenant vrf external-l3 static-route nodeshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route node
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1712
S Commandsshow health tenant vrf external-l3 static-route node
show health tenant vrf external-l3 static-route node detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1713
S Commandsshow health tenant vrf external-l3 static-route node detail
show health tenant vrf multicastshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD multicast
Description: Show multicast configuration per VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD multicast
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1714
S Commandsshow health tenant vrf multicast
show inband-mgmtshow inband-mgmt
Description: Show inband mgmt epgs on all the nodes
Command Mode: exec : Exec Mode
Command Path:
# show inband-mgmt
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1715
S Commandsshow inband-mgmt
show inband-mgmt controllershow inband-mgmt controller <controller-id> [epg <WORD>]
Description: show inband mgmt epgs on the controller
Syntax:
<controller-id>
(Optional) Epg Name of conusmer epgWORD
Command Mode: exec : Exec Mode
Command Path:
# show inband-mgmt controller <controller-id> [epg <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1716
S Commandsshow inband-mgmt controller
show inband-mgmt switchshow inband-mgmt switch <switch-id> [epg <WORD>]
Description: Show inband mgmt epgs on the node
Syntax:
<switch-id>
(Optional) Epg NameWORD
Command Mode: exec : Exec Mode
Command Path:
# show inband-mgmt switch <switch-id> [epg <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1717
S Commandsshow inband-mgmt switch
show interface bridge-domainshow interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1718
S Commandsshow interface bridge-domain
show interface bridge-domain detailshow interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show interface bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1719
S Commandsshow interface bridge-domain detail
show interface bridge-domain first-hop-security binding-tableshow interface bridge-domain WORD first-hop-security binding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show interface bridge-domain WORD first-hop-security binding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1720
S Commandsshow interface bridge-domain first-hop-security binding-table
show interface bridge-domain first-hop-security statistics arpshow interface bridge-domain WORD first-hop-security statistics arp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show interface bridge-domain WORD first-hop-security statistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1721
S Commandsshow interface bridge-domain first-hop-security statistics arp
show interface bridge-domain first-hop-security statisticsdhcpv4
show interface bridge-domain WORD first-hop-security statistics dhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show interface bridge-domain WORD first-hop-security statistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1722
S Commandsshow interface bridge-domain first-hop-security statistics dhcpv4
show interface bridge-domain first-hop-security statisticsdhcpv6
show interface bridge-domain WORD first-hop-security statistics dhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show interface bridge-domain WORD first-hop-security statistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1723
S Commandsshow interface bridge-domain first-hop-security statistics dhcpv6
show interface bridge-domain first-hop-security statisticsneighbor-discovery
show interface bridge-domain WORD first-hop-security statistics neighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show interface bridge-domain WORD first-hop-security statistics neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1724
S Commandsshow interface bridge-domain first-hop-security statistics neighbor-discovery
show ip interface bridge-domainshow ip interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show ip interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1725
S Commandsshow ip interface bridge-domain
show ipv6 interface bridge-domainshow ipv6 interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show ipv6 interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1726
S Commandsshow ipv6 interface bridge-domain
show l4l7-clustershow l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]
Description: Show L4 L7 Device information
Syntax:
(Optional) Name of TenantTenant Name
(Optional) Name of DeviceDevice Cluster Name
Command Mode: exec : Exec Mode
Command Path:
# show l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1727
S Commandsshow l4l7-cluster
show l4l7-graphshow l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]
Description: Show L4 L7 Graph information
Syntax:
(Optional) Name of Tenant<Tenant Name>
(Optional) Name of Graph<Graph Name>
Command Mode: exec : Exec Mode
Command Path:
# show l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1728
S Commandsshow l4l7-graph
show l4l7-packageshow l4l7-package
Description: Show L4-L7 package information
Command Mode: exec : Exec Mode
Command Path:
# show l4l7-package
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1729
S Commandsshow l4l7-package
show ldap-servershow ldap-server
Description: Show LDAP server information
Command Mode: exec : Exec Mode
Command Path:
# show ldap-server
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1730
S Commandsshow ldap-server
show locator-ledshow locator-led status
Description: Show command for locator-led
Syntax:
locator-led statusstatus
Command Mode: exec : Exec Mode
Command Path:
# show locator-led status
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1731
S Commandsshow locator-led
show locator-led status leafshow locator-led status leaf
Description: Leaf to filter on
Syntax:
locator-led statusstatus
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show locator-led status leaf
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1732
S Commandsshow locator-led status leaf
show microsoft domainshow microsoft domain
Description: Show Microsoft domain information
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1733
S Commandsshow microsoft domain
show microsoft domain nameshow microsoft domain name <WORD>
Description:Microsoft domain name
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1734
S Commandsshow microsoft domain name
show microsoft domain name hypervshow microsoft domain name <WORD> hyperv <WORD>
Description: Show Microsoft Hypervisor information
Syntax:
Microsoft domain nameWORD
HyperV hostnameWORD
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> hyperv <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1735
S Commandsshow microsoft domain name hyperv
show microsoft domain name port-groupshow microsoft domain name <WORD> port-group
Description: Show Microsoft port group information
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> port-group
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1736
S Commandsshow microsoft domain name port-group
show microsoft domain name scvmmshow microsoft domain name <WORD> scvmm <hostname|ip>
Description: Show Microsoft SCVMM information
Syntax:
Microsoft domain nameWORD
SCVMM hostname or IP<hostname|ip>
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> scvmm <hostname|ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1737
S Commandsshow microsoft domain name scvmm
show microsoft domain name vmshow microsoft domain name <WORD> vm
Description: Show Microsoft VM information
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> vm
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1738
S Commandsshow microsoft domain name vm
show microsoft domain name vm nameshow microsoft domain name <WORD> vm name <WORD>
Description: Show detailed Microsoft VM information
Syntax:
Microsoft domain nameWORD
VM NameWORD
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> vm name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1739
S Commandsshow microsoft domain name vm name
show microsoft vmshow microsoft vm [name <WORD>] [ip <A.B.C.D>] [mac <AA:BB:CC:DD:EE:FF>]
Description: Show Microsoft VM information
Syntax:
(Optional) Specify a VM nameWORD
(Optional) Specify a VM IP addressA.B.C.D
(Optional) Specify a VM MAC addressAA:BB:CC:DD:EE:FF
Command Mode: exec : Exec Mode
Command Path:
# show microsoft vm [name <WORD>] [ip <A.B.C.D>] [mac <AA:BB:CC:DD:EE:FF>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1740
S Commandsshow microsoft vm
show monitor accessshow monitor access session session_name
Description: Show monitor session for access interfaces
Syntax:
sessionsession
session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show monitor access session session_name
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1741
S Commandsshow monitor access
show monitor fabricshow monitor fabric session session_name
Description: Show monitor session for fabric interfaces
Syntax:
sessionsession
session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show monitor fabric session session_name
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1742
S Commandsshow monitor fabric
show monitor summaryshow monitor summary
Description: Show brief summary of all non-virtual monitor sessions
Command Mode: exec : Exec Mode
Command Path:
# show monitor summary
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1743
S Commandsshow monitor summary
show monitor tenantshow monitor tenant <tenant_name> session session_name
Description: Show monitor session for tenant
Syntax:
tenanttenant_name
sessionsession
session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show monitor tenant <tenant_name> session session_name
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1744
S Commandsshow monitor tenant
show monitor virtualshow monitor virtual session WORD
Description: Show monitor session for virtual switches
Syntax:
sessionsession
Session nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show monitor virtual session WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1745
S Commandsshow monitor virtual
show name-alias tenantshow name-alias tenant WORD
Description: Show corresponding tenants for Alias
Syntax:
Name of the tenant Alias to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show name-alias tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1746
S Commandsshow name-alias tenant
show name-alias tenant aclshow name-alias tenant WORD acl WORD
Description: Show Acl Name for alias
Syntax:
Name of the tenant Alias to filter on (Max Size 63)WORD
Name of the Acl Alias to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show name-alias tenant WORD acl WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1747
S Commandsshow name-alias tenant acl
show name-alias tenant applicationshow name-alias tenant WORD application WORD
Description: Show Application Name for alias
Syntax:
Name of the tenant Alias to filter on (Max Size 63)WORD
Name of the application Alias to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show name-alias tenant WORD application WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1748
S Commandsshow name-alias tenant application
show name-alias tenant application epgshow name-alias tenant WORD application WORD epg WORD
Description: Show EndPoint Group Name for alias
Syntax:
Name of the tenant Alias to filter on (Max Size 63)WORD
Name of the application Alias to filter on (Max Size 64)WORD
Name of the epg Alias to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show name-alias tenant WORD application WORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1749
S Commandsshow name-alias tenant application epg
show name-alias tenant bridge-domainshow name-alias tenant WORD bridge-domain WORD
Description: Show Bridge-Domain Name for alias
Syntax:
Name of the tenant Alias to filter on (Max Size 63)WORD
Name of the bridge-domain Alias to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show name-alias tenant WORD bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1750
S Commandsshow name-alias tenant bridge-domain
show name-alias tenant contractshow name-alias tenant WORD contract WORD
Description: Show Contract Name for alias
Syntax:
Name of the tenant Alias to filter on (Max Size 63)WORD
Name of the contract Alias to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show name-alias tenant WORD contract WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1751
S Commandsshow name-alias tenant contract
show name-alias tenant contract subjectshow name-alias tenant WORD contract WORD subject WORD
Description: Show Subject Name for alias
Syntax:
Name of the tenant Alias to filter on (Max Size 63)WORD
Name of the contract Alias to filter on (Max Size 64)WORD
Name of the Subject Alias to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show name-alias tenant WORD contract WORD subject WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1752
S Commandsshow name-alias tenant contract subject
show name-alias tenant l3outshow name-alias tenant WORD l3out WORD
Description: Show L3out Name for alias
Syntax:
Name of the tenant Alias to filter on (Max Size 63)WORD
Name of the L3out Alias to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show name-alias tenant WORD l3out WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1753
S Commandsshow name-alias tenant l3out
show name-alias tenant vrfshow name-alias tenant WORD vrf WORD
Description: Show Vrf Name for alias
Syntax:
Name of the tenant Alias to filter on (Max Size 63)WORD
Name of the vrf Alias to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show name-alias tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1754
S Commandsshow name-alias tenant vrf
show ntpqshow ntpq
Description: Show ntpq information
Command Mode: exec : Exec Mode
Command Path:
# show ntpq
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1755
S Commandsshow ntpq
show oob-mgmtshow oob-mgmt
Description: Show Out of band Information
Command Mode: exec : Exec Mode
Command Path:
# show oob-mgmt
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1756
S Commandsshow oob-mgmt
show oob-mgmt controllershow oob-mgmt controller <controller-id> [epg <WORD>]
Description: Show oob mgmt epgs on the controller, enter one
Syntax:
<controller-id>
(Optional) Epg Name of conusmer epgWORD
Command Mode: exec : Exec Mode
Command Path:
# show oob-mgmt controller <controller-id> [epg <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1757
S Commandsshow oob-mgmt controller
show oob-mgmt switchshow oob-mgmt switch <switch-id> [epg <WORD>]
Description: Show oob mgmt epgs on the node, enter one
Syntax:
<switch-id>
(Optional) Epg Name of conusmer epgWORD
Command Mode: exec : Exec Mode
Command Path:
# show oob-mgmt switch <switch-id> [epg <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1758
S Commandsshow oob-mgmt switch
show pd-recovery statusshow pd-recovery status
Description: Show policydist shard recovery from policymgr shards status
Command Mode: exec : Exec Mode
Command Path:
# show pd-recovery status
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1759
S Commandsshow pd-recovery status
show policy-mapshow policy-map
Description: Show policy maps
Command Mode: exec : Exec Mode
Command Path:
# show policy-map
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1760
S Commandsshow policy-map
show policy-map type data-planeshow policy-map type data-plane infra WORD [stats]
Description: Data-plane type policy-map(s)
Syntax:
Global data-plane policy-map(s)infra
data-plane type policy-map(s) (Max Size 64)WORD
(Optional) Data-Plane Policer Statistics, where availablestats
Command Mode: exec : Exec Mode
Command Path:
# show policy-map type data-plane infra WORD [stats]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1761
S Commandsshow policy-map type data-plane
show policy-map type qosshow policy-map type qos WORD
Description: QOS type policy-map(s)
Syntax:
QOS type policy-map(s) (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show policy-map type qos WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1762
S Commandsshow policy-map type qos
show port-channel leafshow port-channel leaf WORD <port-channel-list>
Description: Show leaf port-channel info
Syntax:
Leaf Range or Leaf Name ListWORD
port channel names<port-channel-list>
Command Mode: exec : Exec Mode
Command Path:
# show port-channel leaf WORD <port-channel-list>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1763
S Commandsshow port-channel leaf
show port-channel mapshow port-channel map <port-channel-list>
Description: Show port-channel mapping
Syntax:
port channel names<port-channel-list>
Command Mode: exec : Exec Mode
Command Path:
# show port-channel map <port-channel-list>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1764
S Commandsshow port-channel map
show port-channel map leafshow port-channel map <port-channel-list> leaf WORD [fex <101-164>]
Description: Leaf
Syntax:
port channel names<port-channel-list>
Leaf Range or Leaf Name ListWORD
(Optional) Fex ID<101-164>
Command Mode: exec : Exec Mode
Command Path:
# show port-channel map <port-channel-list> leaf WORD [fex <101-164>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1765
S Commandsshow port-channel map leaf
show pwd-rulesshow pwd-rules
Description: Show Password Rules
Command Mode: exec : Exec Mode
Command Path:
# show pwd-rules
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1766
S Commandsshow pwd-rules
show quotashow quota
Description: Show Quotas Information
Command Mode: exec : Exec Mode
Command Path:
# show quota
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1767
S Commandsshow quota
show radius-servershow radius-server
Description: Show RADIUS server information
Command Mode: exec : Exec Mode
Command Path:
# show radius-server
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1768
S Commandsshow radius-server
show resourceshow resource conflict encap-vlan
Description: Show resource information
Syntax:
show resource conflicts in APICconflict
show resource conflicts of encap-vlan in APICencap-vlan
Command Mode: exec : Exec Mode
Command Path:
# show resource conflict encap-vlan
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1769
S Commandsshow resource
show resource conflict encap-vlan epgshow resource conflict encap-vlan epg <WORD>
Description: Epg Name
Syntax:
show resource conflicts in APICconflict
show resource conflicts of encap-vlan in APICencap-vlan
Epg NameWORD
Command Mode: exec : Exec Mode
Command Path:
# show resource conflict encap-vlan epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1770
S Commandsshow resource conflict encap-vlan epg
show resource conflict encap-vlan epg nodeshow resource conflict encap-vlan epg <WORD> node <101-4000>
Description: Node ID
Syntax:
show resource conflicts in APICconflict
show resource conflicts of encap-vlan in APICencap-vlan
Epg NameWORD
Leaf ID<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show resource conflict encap-vlan epg <WORD> node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1771
S Commandsshow resource conflict encap-vlan epg node
show roleshow role
Description: Show information about AAA Roles
Command Mode: exec : Exec Mode
Command Path:
# show role
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1772
S Commandsshow role
show running-configshow running-config [all] <scope>
Description: Show running configuration
Syntax:
(Optional) Show running-config with defaultsall
command scope<scope>
Command Mode: exec : Exec Mode
Command Path:
# show running-config [all] <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1773
S Commandsshow running-config
show sessionsshow sessions [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show session-log information
Syntax:
(Optional) Log ID<log-id>
(Optional) Object action indicatoraction<action-type>
(Optional) Name of user<user-name>
(Optional) Logs created in time interval. Number range from=1 to=59<num-minutes>
(Optional) Logs created in time interval. Number range from=1 to=23<num-hours>
(Optional) Logs created in time interval. Number range from=1 to=999<num-days>
(Optional) Logs created in time interval<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Logs created in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Detailed session-log information. Displays the action triggerthat shows why a login occurred.
detail
command scope<scope>
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1774
S Commandsshow sessions
show sessions controllershow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]controller
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] controller
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1775
S Commandsshow sessions controller
show sessions controller detailshow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]controller detail [id <node-id>]
Description: Detailed controller information
Syntax:
(Optional) Optional Serial numbernode-id
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] controller detail [id <node-id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1776
S Commandsshow sessions controller detail
show sessions leafshow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]leaf <leafId>
Description: Show command for leaf
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] leaf <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1777
S Commandsshow sessions leaf
show sessions spineshow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]spine <leafId>
Description: Show command for spine
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] spine <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1778
S Commandsshow sessions spine
show snapshot activeshow snapshot active job
Description: Show command for active snapshot job
Syntax:
View active snapshot jobjob
Command Mode: exec : Exec Mode
Command Path:
# show snapshot active job
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1779
S Commandsshow snapshot active
show snapshot filesshow snapshot files
Description: Show command for snapshot files
Command Mode: exec : Exec Mode
Command Path:
# show snapshot files
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1780
S Commandsshow snapshot files
show snapshot jobsshow snapshot jobs <WORD>
Description: Show command for snapshot jobs
Syntax:
Snapshot policy nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show snapshot jobs <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1781
S Commandsshow snapshot jobs
show snmpshow snmp [policy <policy>]
Description: Show snmp policy information
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1782
S Commandsshow snmp
show snmp clientgroupsshow snmp [policy <policy>] clientgroups
Description: Show snmp client group policies
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] clientgroups
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1783
S Commandsshow snmp clientgroups
show snmp communityshow snmp [policy <policy>] community
Description: Show snmp community information
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] community
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1784
S Commandsshow snmp community
show snmp engineidshow snmp [policy <policy>] engineid
Description: Show snmp v3 engine-id
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] engineid
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1785
S Commandsshow snmp engineid
show snmp hostsshow snmp [policy <policy>] hosts
Description: Show snmp trap hosts
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] hosts
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1786
S Commandsshow snmp hosts
show snmp summaryshow snmp [policy <policy>] summary
Description: Show snmp summary
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] summary
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1787
S Commandsshow snmp summary
show snmp usersshow snmp [policy <policy>] users
Description: Show snmp v3 users
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] users
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1788
S Commandsshow snmp users
show statsshow stats granularity <granularity-value> [history] [cumulative] tenant|leaf|spine
Description: Show statistics
Syntax:
Choose granularity valuegranularity
<granularity-value><granularity-value>
(Optional) historical stats informationhistory
(Optional) cumulative stats informationcumulative
command scopetenant
command scopeleaf
command scopespine
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant|leaf|spine
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1789
S Commandsshow stats
show stats granularity communication controllershow stats granularity <granularity-value> [history] [cumulative] communication controller node-id
Description: Show command for nginx web-requests
Syntax:
node-idnode-id
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] communication controllernode-id
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1790
S Commandsshow stats granularity communication controller
show stats granularity leafshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId>
Description: Show command for leaf
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1791
S Commandsshow stats granularity leaf
show stats granularity leaf fexshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex <fexNum>
Description: Show extended chassis information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex<fexNum>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1792
S Commandsshow stats granularity leaf fex
show stats granularity leaf fex moduleshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex<fexNum> module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1793
S Commandsshow stats granularity leaf fex module
show stats granularity leaf interface ethernetshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interfaceethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1794
S Commandsshow stats granularity leaf interface ethernet
show stats granularity leaf interface mgmtshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interfacemgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1795
S Commandsshow stats granularity leaf interface mgmt
show stats granularity leaf interface portchannelshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface portchannel <portChan>
Description: Port channel interface
Syntax:
Leaf id<leafId>
<Port channel number><portChan>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interfaceportchannel <portChan>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1796
S Commandsshow stats granularity leaf interface portchannel
show stats granularity leaf inventory chassisshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventorychassis
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1797
S Commandsshow stats granularity leaf inventory chassis
show stats granularity leaf inventory fansshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventoryfans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1798
S Commandsshow stats granularity leaf inventory fans
show stats granularity leaf inventory powersupplyshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1799
S Commandsshow stats granularity leaf inventory powersupply
show stats granularity leaf inventory supervisorshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventorysupervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1800
S Commandsshow stats granularity leaf inventory supervisor
show stats granularity spineshow stats granularity <granularity-value> [history] [cumulative] spine <leafId>
Description: Show command for spine
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1801
S Commandsshow stats granularity spine
show stats granularity spine interface ethernetshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> interfaceethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1802
S Commandsshow stats granularity spine interface ethernet
show stats granularity spine interface mgmtshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> interfacemgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1803
S Commandsshow stats granularity spine interface mgmt
show stats granularity spine inventory chassisshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorychassis
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1804
S Commandsshow stats granularity spine inventory chassis
show stats granularity spine inventory fabricshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory fabric <fcMod>
Description: Show information for fabric module
Syntax:
Leaf id<leafId>
pls enter the fabric module number<fcMod>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventoryfabric <fcMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1805
S Commandsshow stats granularity spine inventory fabric
show stats granularity spine inventory fansshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventoryfans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1806
S Commandsshow stats granularity spine inventory fans
show stats granularity spine inventory moduleshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorymodule <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1807
S Commandsshow stats granularity spine inventory module
show stats granularity spine inventory powersupplyshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory powersupply<psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1808
S Commandsshow stats granularity spine inventory powersupply
show stats granularity spine inventory supervisorshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorysupervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1809
S Commandsshow stats granularity spine inventory supervisor
show stats granularity spine inventory systemshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory system <sysMod>
Description: Show information for system module
Syntax:
Leaf id<leafId>
pls enter the system module number<sysMod>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorysystem <sysMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1810
S Commandsshow stats granularity spine inventory system
show stats granularity tenantshow stats granularity <granularity-value> [history] [cumulative] tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1811
S Commandsshow stats granularity tenant
show stats granularity tenant applicationshow stats granularity <granularity-value> [history] [cumulative] tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD applicationWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1812
S Commandsshow stats granularity tenant application
show stats granularity tenant application epgshow stats granularity <granularity-value> [history] [cumulative] tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD applicationWORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1813
S Commandsshow stats granularity tenant application epg
show stats granularity tenant dnsservergroupshow stats granularity <granularity-value> [history] [cumulative] tenant WORD dnsservergroup WORD
Description: Show Dns Server Group Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD dnsservergroupWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1814
S Commandsshow stats granularity tenant dnsservergroup
show stats granularity tenant dnsservergroup servershow stats granularity <granularity-value> [history] [cumulative] tenant WORD dnsservergroup WORD serverWORD
Description: Show Dns Server Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD dnsservergroupWORD server WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1815
S Commandsshow stats granularity tenant dnsservergroup server
show stats granularity tenant dnsservergroup server domainshow stats granularity <granularity-value> [history] [cumulative] tenant WORD dnsservergroup WORD serverWORD domain WORD
Description: Show Dns Domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Domain we eventually want to filter on (Max Size 512)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD dnsservergroupWORD server WORD domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1816
S Commandsshow stats granularity tenant dnsservergroup server domain
show stats granularity tenant dot1q-tunnelshow stats granularity <granularity-value> [history] [cumulative] tenant WORD dot1q-tunnel WORD
Description: Show Dot1q-tunnel Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the TnlEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD dot1q-tunnelWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1817
S Commandsshow stats granularity tenant dot1q-tunnel
show stats granularity tenant multicast-route-mapsshow stats granularity <granularity-value> [history] [cumulative] tenant WORD multicast-route-maps
Description: Show multicast route-maps per Tenant
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORDmulticast-route-maps
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1818
S Commandsshow stats granularity tenant multicast-route-maps
show stats granularity tenant vrfshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD
Description: Show VRF Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1819
S Commandsshow stats granularity tenant vrf
show stats granularity tenant vrf acllog l2show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD acllog <permitDrop>l2 flow vlan <NUMBER> srcintf <srcintf>
Description: L2 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flowi statsflow
vlan infovlan
<vlan>. Number range from=0 to=9223372036854775807<vlan>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDacllog <permitDrop> l2 flow vlan <NUMBER> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1820
S Commandsshow stats granularity tenant vrf acllog l2
show stats granularity tenant vrf acllog l3show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD acllog <permitDrop>l3 flow srcip <A.B.C.D or A:B::C:D> dstip <A.B.C.D or A:B::C:D> proto <proto> srcport <srcport> dstport <dstport>srcintf <srcintf>
Description: L3 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flow statsflow
source ipsrcip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
destination ipdstip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
protocolproto
<proto><proto>
source portsrcport
<srcport><srcport>
destination portdstport
<dstport><dstport>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDacllog <permitDrop> l3 flow srcip <A.B.C.D or A:B::C:D> dstip <A.B.C.D or A:B::C:D> proto<proto> srcport <srcport> dstport <dstport> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1821
S Commandsshow stats granularity tenant vrf acllog l3
show stats granularity tenant vrf detailshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDdetail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1822
S Commandsshow stats granularity tenant vrf detail
show stats granularity tenant vrf external-l3 bgpshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 bgp
Description: Show command for BGP peers
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1823
S Commandsshow stats granularity tenant vrf external-l3 bgp
show stats granularity tenant vrf external-l3 bgp nodeshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 bgpnode <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 bgp node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1824
S Commandsshow stats granularity tenant vrf external-l3 bgp node
show stats granularity tenant vrf external-l3 eigrpshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 eigrp
Description: Show external l3 EIGRP
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1825
S Commandsshow stats granularity tenant vrf external-l3 eigrp
show stats granularity tenant vrf external-l3 eigrp detailshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 eigrpdetail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1826
S Commandsshow stats granularity tenant vrf external-l3 eigrp detail
show stats granularity tenant vrf external-l3 epgshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 epg<epgName>
Description: Show command for external-l3 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1827
S Commandsshow stats granularity tenant vrf external-l3 epg
show stats granularity tenant vrf external-l3 epg detailshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 epg<epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 epg <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1828
S Commandsshow stats granularity tenant vrf external-l3 epg detail
show stats granularity tenant vrf external-l3 epg nameshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 epg<epgName> name <epgName>
Description: EPG name to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 epg <epgName> name <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1829
S Commandsshow stats granularity tenant vrf external-l3 epg name
show stats granularity tenant vrf external-l3 epg name detailshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 epg<epgName> name <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 epg <epgName> name <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1830
S Commandsshow stats granularity tenant vrf external-l3 epg name detail
show stats granularity tenant vrf external-l3 interfacesshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 interfaces
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1831
S Commandsshow stats granularity tenant vrf external-l3 interfaces
show stats granularity tenant vrf external-l3 interfaces detailshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 interfacesdetail
Description: Show interfaces details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 interfaces detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1832
S Commandsshow stats granularity tenant vrf external-l3 interfaces detail
show stats granularity tenant vrf external-l3 ospfshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 ospf
Description: Show command for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1833
S Commandsshow stats granularity tenant vrf external-l3 ospf
show stats granularity tenant vrf external-l3 ospf detailshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3 ospfdetail
Description: Show internal details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1834
S Commandsshow stats granularity tenant vrf external-l3 ospf detail
show stats granularity tenant vrf external-l3 static-routeshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3static-route
Description: Show command for external-l3 static routes
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1835
S Commandsshow stats granularity tenant vrf external-l3 static-route
show stats granularity tenant vrf external-l3 static-route detailshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3static-route detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 static-route detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1836
S Commandsshow stats granularity tenant vrf external-l3 static-route detail
show stats granularity tenant vrf external-l3 static-route nodeshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3static-route node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 static-route node
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1837
S Commandsshow stats granularity tenant vrf external-l3 static-route node
show stats granularity tenant vrf external-l3 static-route nodedetail
show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD external-l3static-route node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDexternal-l3 static-route node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1838
S Commandsshow stats granularity tenant vrf external-l3 static-route node detail
show stats granularity tenant vrf multicastshow stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORD multicast
Description: Show multicast configuration per VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD vrf WORDmulticast
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1839
S Commandsshow stats granularity tenant vrf multicast
show switchshow switch
Description: Show switch information
Command Mode: exec : Exec Mode
Command Path:
# show switch
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1840
S Commandsshow switch
show switch detailshow switch detail [id <switch-id>]
Description: Show switch detailed information
Syntax:
(Optional) Optional switch id. Number range from=0to=9223372036854775807
switch-id
Command Mode: exec : Exec Mode
Command Path:
# show switch detail [id <switch-id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1841
S Commandsshow switch detail
show tacacs-servershow tacacs-server
Description: Show tacacs server information
Command Mode: exec : Exec Mode
Command Path:
# show tacacs-server
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1842
S Commandsshow tacacs-server
show techsupport allshow techsupport all status
Description: Techsupport status for all
Syntax:
Statusstatus
Command Mode: exec : Exec Mode
Command Path:
# show techsupport all status
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1843
S Commandsshow techsupport all
show techsupport controllersshow techsupport controllers status
Description: Techsupport status for controllers
Syntax:
Statusstatus
Command Mode: exec : Exec Mode
Command Path:
# show techsupport controllers status
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1844
S Commandsshow techsupport controllers
show techsupport hostshow techsupport host <NUMBER> status
Description: Techsupport status for host
Syntax:
Specify the host Odev ID. Number range from=0to=9223372036854775807
<Odevid>
Statusstatus
Command Mode: exec : Exec Mode
Command Path:
# show techsupport host <NUMBER> status
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1845
S Commandsshow techsupport host
show techsupport switchshow techsupport switch switchId <switchId> status
Description: Techsupport status for switch
Syntax:
switch id 101-4000 or range(s): 101-103,104switchId <switchId>
Statusstatus
Command Mode: exec : Exec Mode
Command Path:
# show techsupport switch switchId <switchId> status
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1846
S Commandsshow techsupport switch
show tenantshow tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1847
S Commandsshow tenant
show tenant access-listshow tenant WORD access-list WORD
Description: Show Access-list Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the Contract to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD access-list WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1848
S Commandsshow tenant access-list
show tenant applicationshow tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1849
S Commandsshow tenant application
show tenant application endpointsshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1850
S Commandsshow tenant application endpoints
show tenant application endpoints leaf interface ethernetshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface ethernet
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Ethernet Rangeethernet [<fex>/]<slot>/<port>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf<WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1851
S Commandsshow tenant application endpoints leaf interface ethernet
show tenant application endpoints leaf interface port-channelshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on an interface port-channel
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199<101-199>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf<WORD> interface port-channel <WORD> [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1852
S Commandsshow tenant application endpoints leaf interface port-channel
show tenant application endpoints vpcshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]
Description: Show IP endpoints on vpc
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpccontext <WORD> <WORD> interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1853
S Commandsshow tenant application endpoints vpc
show tenant application epgshow tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1854
S Commandsshow tenant application epg
show tenant application epg detailshow tenant WORD application WORD epg WORD detail
Description: Show detailed view of Application EPg
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1855
S Commandsshow tenant application epg detail
show tenant application epg endpointsshow tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1856
S Commandsshow tenant application epg endpoints
show tenant application epg endpoints leaf interface ethernetshow tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface ethernet
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Ethernet Rangeethernet [<fex>/]<slot>/<port>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1857
S Commandsshow tenant application epg endpoints leaf interface ethernet
show tenant application epg endpoints leaf interfaceport-channel
show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on an interface port-channel
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199<101-199>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1858
S Commandsshow tenant application epg endpoints leaf interface port-channel
show tenant application epg endpoints vpcshow tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]
Description: Show IP endpoints on vpc
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1859
S Commandsshow tenant application epg endpoints vpc
EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1860
S Commandsshow tenant application epg endpoints vpc
show tenant bridge-domainshow tenant WORD bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1861
S Commandsshow tenant bridge-domain
show tenant bridge-domain detailshow tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1862
S Commandsshow tenant bridge-domain detail
show tenant bridge-domain first-hop-security binding-tableshow tenant WORD bridge-domain WORD first-hop-security binding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD bridge-domain WORD first-hop-security binding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1863
S Commandsshow tenant bridge-domain first-hop-security binding-table
show tenant bridge-domain first-hop-security statistics arpshow tenant WORD bridge-domain WORD first-hop-security statistics arp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD bridge-domain WORD first-hop-security statistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1864
S Commandsshow tenant bridge-domain first-hop-security statistics arp
show tenant bridge-domain first-hop-security statistics dhcpv4show tenant WORD bridge-domain WORD first-hop-security statistics dhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD bridge-domain WORD first-hop-security statistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1865
S Commandsshow tenant bridge-domain first-hop-security statistics dhcpv4
show tenant bridge-domain first-hop-security statistics dhcpv6show tenant WORD bridge-domain WORD first-hop-security statistics dhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD bridge-domain WORD first-hop-security statistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1866
S Commandsshow tenant bridge-domain first-hop-security statistics dhcpv6
show tenant bridge-domain first-hop-security statisticsneighbor-discovery
show tenant WORD bridge-domain WORD first-hop-security statistics neighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD bridge-domain WORD first-hop-security statistics neighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1867
S Commandsshow tenant bridge-domain first-hop-security statistics neighbor-discovery
show tenant contract-typeshow tenant WORD contract-type WORD
Description: Show Contracts Information Based on Type
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
whitelist (permit) or blacklist(deny) or oob-mgmt type of contractWORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD contract-type WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1868
S Commandsshow tenant contract-type
show tenant contractshow tenant WORD contract WORD
Description: Show Contracts Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the Contract to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD contract WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1869
S Commandsshow tenant contract
show tenant detailshow tenant WORD detail
Description: Show detailed view of tenant
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1870
S Commandsshow tenant detail
show tenant dnsservergroupshow tenant WORD dnsservergroup WORD
Description: Show Dns Server Group Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD dnsservergroup WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1871
S Commandsshow tenant dnsservergroup
show tenant dnsservergroup servershow tenant WORD dnsservergroup WORD server WORD
Description: Show Dns Server Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD dnsservergroup WORD server WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1872
S Commandsshow tenant dnsservergroup server
show tenant dnsservergroup server domainshow tenant WORD dnsservergroup WORD server WORD domain WORD
Description: Show Dns Domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the dns server group we eventually want to filter on (Max Size16)
WORD
IP of server we eventually want to filter on (Max Size None)WORD
Domain we eventually want to filter on (Max Size 512)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD dnsservergroup WORD server WORD domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1873
S Commandsshow tenant dnsservergroup server domain
show tenant dot1q-tunnelshow tenant WORD dot1q-tunnel WORD
Description: Show Dot1q-tunnel Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the TnlEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD dot1q-tunnel WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1874
S Commandsshow tenant dot1q-tunnel
show tenant endpointsshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1875
S Commandsshow tenant endpoints
show tenant endpoints leaf interface ethernetshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet[<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface ethernet
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Ethernet Rangeethernet [<fex>/]<slot>/<port>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1876
S Commandsshow tenant endpoints leaf interface ethernet
show tenant endpoints leaf interface port-channelshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex<NUMBER>]
Description: Show IP endpoints on an interface port-channel
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199<101-199>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1877
S Commandsshow tenant endpoints leaf interface port-channel
show tenant endpoints vpcshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD>[fex <fex>]
Description: Show IP endpoints on vpc
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP Unicast address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=199fex
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1878
S Commandsshow tenant endpoints vpc
show tenant epgshow tenant WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1879
S Commandsshow tenant epg
show tenant epg detailshow tenant WORD epg WORD detail
Description: Show detailed view of Application EPg
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD epg WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1880
S Commandsshow tenant epg detail
show tenant external-l2 epgshow tenant WORD external-l2 epg WORD
Description: Show command for external-l2 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the EPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD external-l2 epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1881
S Commandsshow tenant external-l2 epg
show tenant interface bridge-domainshow tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1882
S Commandsshow tenant interface bridge-domain
show tenant interface bridge-domain detailshow tenant WORD interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD interface bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1883
S Commandsshow tenant interface bridge-domain detail
show tenant interface bridge-domain first-hop-securitybinding-table
show tenant WORD interface bridge-domain WORD first-hop-security binding-table
Description: Show Bridge-domain Binding Table Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD interface bridge-domain WORD first-hop-security binding-table
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1884
S Commandsshow tenant interface bridge-domain first-hop-security binding-table
show tenant interface bridge-domain first-hop-securitystatistics arp
show tenant WORD interface bridge-domain WORD first-hop-security statistics arp
Description: Show Bridge-domain First Hop Security ARP Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD interface bridge-domain WORD first-hop-security statistics arp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1885
S Commandsshow tenant interface bridge-domain first-hop-security statistics arp
show tenant interface bridge-domain first-hop-securitystatistics dhcpv4
show tenant WORD interface bridge-domain WORD first-hop-security statistics dhcpv4
Description: Show Bridge-domain First Hop Security DHCPv4 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD interface bridge-domain WORD first-hop-security statistics dhcpv4
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1886
S Commandsshow tenant interface bridge-domain first-hop-security statistics dhcpv4
show tenant interface bridge-domain first-hop-securitystatistics dhcpv6
show tenant WORD interface bridge-domain WORD first-hop-security statistics dhcpv6
Description: Show Bridge-domain First Hop Security DHCPv6 Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD interface bridge-domain WORD first-hop-security statistics dhcpv6
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1887
S Commandsshow tenant interface bridge-domain first-hop-security statistics dhcpv6
show tenant interface bridge-domain first-hop-securitystatistics neighbor-discovery
show tenant WORD interface bridge-domain WORD first-hop-security statistics neighbor-discovery
Description: Show Bridge-domain First Hop Security Neighbor Discovery Statistics
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD interface bridge-domain WORD first-hop-security statisticsneighbor-discovery
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1888
S Commandsshow tenant interface bridge-domain first-hop-security statistics neighbor-discovery
show tenant ip interface bridge-domainshow tenant WORD ip interface bridge-domain WORD
Description: Show command for IP properties on interface BD
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD ip interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1889
S Commandsshow tenant ip interface bridge-domain
show tenant ipv6 interface bridge-domainshow tenant WORD ipv6 interface bridge-domain WORD
Description: Show command for IP properties on interface BD
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD ipv6 interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1890
S Commandsshow tenant ipv6 interface bridge-domain
show tenant multicast-route-mapsshow tenant WORD multicast-route-maps
Description: Show multicast route-maps per Tenant
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD multicast-route-maps
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1891
S Commandsshow tenant multicast-route-maps
show tenant policy-mapshow tenant WORD policy-map
Description: Show policy maps
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD policy-map
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1892
S Commandsshow tenant policy-map
show tenant policy-map type data-planeshow tenant WORD policy-map type data-plane WORD [stats]
Description: Data-plane type policy-map(s)
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
data-plane type policy-map(s) (Max Size 64)WORD
(Optional) Data-Plane Policer Statistics, where availablestats
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD policy-map type data-plane WORD [stats]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1893
S Commandsshow tenant policy-map type data-plane
show tenant policy-map type qosshow tenant WORD policy-map type qos WORD
Description: QOS type policy-map(s)
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
QOS type policy-map(s) (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD policy-map type qos WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1894
S Commandsshow tenant policy-map type qos
show tenant vrfshow tenant WORD vrf WORD
Description: Show VRF Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1895
S Commandsshow tenant vrf
show tenant vrf acllog l2show tenant WORD vrf WORD acllog <permitDrop> l2 flow vlan <NUMBER> srcintf <srcintf>
Description: L2 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flowi statsflow
vlan infovlan
<vlan>. Number range from=0 to=9223372036854775807<vlan>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD acllog <permitDrop> l2 flow vlan <NUMBER> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1896
S Commandsshow tenant vrf acllog l2
show tenant vrf acllog l3show tenant WORD vrf WORD acllog <permitDrop> l3 flow srcip <A.B.C.D or A:B::C:D> dstip <A.B.C.D orA:B::C:D> proto <proto> srcport <srcport> dstport <dstport> srcintf <srcintf>
Description: L3 flow stats
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
permitDroppermitDrop
flow statsflow
source ipsrcip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
destination ipdstip
IP address in format i.i.i.i or IPv6 address in format xxxx:xxxx, xxxx::xxA.B.C.D or A:B::C:D
protocolproto
<proto><proto>
source portsrcport
<srcport><srcport>
destination portdstport
<dstport><dstport>
source interfacesrcintf
<srcintf><srcintf>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD acllog <permitDrop> l3 flow srcip <A.B.C.D or A:B::C:D> dstip<A.B.C.D or A:B::C:D> proto <proto> srcport <srcport> dstport <dstport> srcintf <srcintf>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1897
S Commandsshow tenant vrf acllog l3
show tenant vrf detailshow tenant WORD vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1898
S Commandsshow tenant vrf detail
show tenant vrf external-l3 bgpshow tenant WORD vrf WORD external-l3 bgp
Description: Show command for BGP peers
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1899
S Commandsshow tenant vrf external-l3 bgp
show tenant vrf external-l3 bgp nodeshow tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 bgp node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1900
S Commandsshow tenant vrf external-l3 bgp node
show tenant vrf external-l3 eigrpshow tenant WORD vrf WORD external-l3 eigrp
Description: Show external l3 EIGRP
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1901
S Commandsshow tenant vrf external-l3 eigrp
show tenant vrf external-l3 eigrp detailshow tenant WORD vrf WORD external-l3 eigrp detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1902
S Commandsshow tenant vrf external-l3 eigrp detail
show tenant vrf external-l3 epgshow tenant WORD vrf WORD external-l3 epg <epgName>
Description: Show command for external-l3 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1903
S Commandsshow tenant vrf external-l3 epg
show tenant vrf external-l3 epg detailshow tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1904
S Commandsshow tenant vrf external-l3 epg detail
show tenant vrf external-l3 epg nameshow tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: EPG name to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1905
S Commandsshow tenant vrf external-l3 epg name
show tenant vrf external-l3 epg name detailshow tenant WORD vrf WORD external-l3 epg <epgName> name <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName> name <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1906
S Commandsshow tenant vrf external-l3 epg name detail
show tenant vrf external-l3 interfacesshow tenant WORD vrf WORD external-l3 interfaces
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1907
S Commandsshow tenant vrf external-l3 interfaces
show tenant vrf external-l3 interfaces detailshow tenant WORD vrf WORD external-l3 interfaces detail
Description: Show interfaces details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 interfaces detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1908
S Commandsshow tenant vrf external-l3 interfaces detail
show tenant vrf external-l3 ospfshow tenant WORD vrf WORD external-l3 ospf
Description: Show command for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1909
S Commandsshow tenant vrf external-l3 ospf
show tenant vrf external-l3 ospf detailshow tenant WORD vrf WORD external-l3 ospf detail
Description: Show internal details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1910
S Commandsshow tenant vrf external-l3 ospf detail
show tenant vrf external-l3 route-mapshow tenant WORD vrf WORD external-l3 route-map [name <l3out name>]
Description: Show command for external-l3 route-map
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
(Optional) Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 route-map [name <l3out name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1911
S Commandsshow tenant vrf external-l3 route-map
show tenant vrf external-l3 route-map detailshow tenant WORD vrf WORD external-l3 route-map [name <l3out name>] detail
Description: Show external-l3 route-map in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
(Optional) Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 route-map [name <l3out name>] detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1912
S Commandsshow tenant vrf external-l3 route-map detail
show tenant vrf external-l3 static-routeshow tenant WORD vrf WORD external-l3 static-route
Description: Show command for external-l3 static routes
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1913
S Commandsshow tenant vrf external-l3 static-route
show tenant vrf external-l3 static-route detailshow tenant WORD vrf WORD external-l3 static-route detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1914
S Commandsshow tenant vrf external-l3 static-route detail
show tenant vrf external-l3 static-route nodeshow tenant WORD vrf WORD external-l3 static-route node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route node
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1915
S Commandsshow tenant vrf external-l3 static-route node
show tenant vrf external-l3 static-route node detailshow tenant WORD vrf WORD external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1916
S Commandsshow tenant vrf external-l3 static-route node detail
show tenant vrf multicastshow tenant WORD vrf WORD multicast
Description: Show multicast configuration per VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD multicast
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1917
S Commandsshow tenant vrf multicast
show troubleshoot epext sessionshow troubleshoot epext session <session_name>
Description: Show session
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1918
S Commandsshow troubleshoot epext session
show troubleshoot epext session atomiccountershow troubleshoot epext session <session_name> atomiccounter
Description: Show atomic counters
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> atomiccounter
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1919
S Commandsshow troubleshoot epext session atomiccounter
show troubleshoot epext session auditshow troubleshoot epext session <session_name> audit
Description: Show audit
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> audit
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1920
S Commandsshow troubleshoot epext session audit
show troubleshoot epext session contractsshow troubleshoot epext session <session_name> contracts
Description: Show contracts
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> contracts
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1921
S Commandsshow troubleshoot epext session contracts
show troubleshoot epext session deploymentsshow troubleshoot epext session <session_name> deployments
Description: Show deployment changes
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> deployments
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1922
S Commandsshow troubleshoot epext session deployments
show troubleshoot epext session eventsshow troubleshoot epext session <session_name> events
Description: Show events
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> events
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1923
S Commandsshow troubleshoot epext session events
show troubleshoot epext session faultsshow troubleshoot epext session <session_name> faults
Description: Show faults
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> faults
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1924
S Commandsshow troubleshoot epext session faults
show troubleshoot epext session latencyshow troubleshoot epext session <session_name> latency
Description: Show latency stats
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> latency
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1925
S Commandsshow troubleshoot epext session latency
show troubleshoot epext session monitorshow troubleshoot epext session <session_name> monitor
Description: Show monitor
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> monitor
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1926
S Commandsshow troubleshoot epext session monitor
show troubleshoot epext session reportsshow troubleshoot epext session <session_name> reports
Description: Show reports
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> reports
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1927
S Commandsshow troubleshoot epext session reports
show troubleshoot epext session statisticsshow troubleshoot epext session <session_name> statistics
Description: Show statistics
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> statistics
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1928
S Commandsshow troubleshoot epext session statistics
show troubleshoot epext session topologyshow troubleshoot epext session <session_name> topology
Description: Show topology
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> topology
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1929
S Commandsshow troubleshoot epext session topology
show troubleshoot epext session tracerouteshow troubleshoot epext session <session_name> traceroute
Description: Show traceroute
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> traceroute
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1930
S Commandsshow troubleshoot epext session traceroute
show troubleshoot epext sessionsshow troubleshoot epext sessions
Description: Show sessions
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext sessions
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1931
S Commandsshow troubleshoot epext sessions
show troubleshoot eptoep sessionshow troubleshoot eptoep session <session_name>
Description: Show session
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1932
S Commandsshow troubleshoot eptoep session
show troubleshoot eptoep session atomiccountershow troubleshoot eptoep session <session_name> atomiccounter
Description: Show atomic counters
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> atomiccounter
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1933
S Commandsshow troubleshoot eptoep session atomiccounter
show troubleshoot eptoep session auditshow troubleshoot eptoep session <session_name> audit
Description: Show audit
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> audit
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1934
S Commandsshow troubleshoot eptoep session audit
show troubleshoot eptoep session contractsshow troubleshoot eptoep session <session_name> contracts
Description: Show contracts
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> contracts
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1935
S Commandsshow troubleshoot eptoep session contracts
show troubleshoot eptoep session deploymentsshow troubleshoot eptoep session <session_name> deployments
Description: Show deployment changes
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> deployments
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1936
S Commandsshow troubleshoot eptoep session deployments
show troubleshoot eptoep session eventsshow troubleshoot eptoep session <session_name> events
Description: Show events
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> events
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1937
S Commandsshow troubleshoot eptoep session events
show troubleshoot eptoep session faultsshow troubleshoot eptoep session <session_name> faults
Description: Show faults
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> faults
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1938
S Commandsshow troubleshoot eptoep session faults
show troubleshoot eptoep session latencyshow troubleshoot eptoep session <session_name> latency
Description: Show latency stats
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> latency
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1939
S Commandsshow troubleshoot eptoep session latency
show troubleshoot eptoep session monitorshow troubleshoot eptoep session <session_name> monitor
Description: Show monitor
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> monitor
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1940
S Commandsshow troubleshoot eptoep session monitor
show troubleshoot eptoep session reportsshow troubleshoot eptoep session <session_name> reports
Description: Show reports
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> reports
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1941
S Commandsshow troubleshoot eptoep session reports
show troubleshoot eptoep session statisticsshow troubleshoot eptoep session <session_name> statistics
Description: Show statistics
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> statistics
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1942
S Commandsshow troubleshoot eptoep session statistics
show troubleshoot eptoep session topologyshow troubleshoot eptoep session <session_name> topology
Description: Show topology
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> topology
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1943
S Commandsshow troubleshoot eptoep session topology
show troubleshoot eptoep session tracerouteshow troubleshoot eptoep session <session_name> traceroute
Description: Show traceroute
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> traceroute
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1944
S Commandsshow troubleshoot eptoep session traceroute
show troubleshoot eptoep sessionsshow troubleshoot eptoep sessions
Description: Show sessions
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep sessions
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1945
S Commandsshow troubleshoot eptoep sessions
show usernameshow username <WORD>
Description: Show user information
Syntax:
User nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show username <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1946
S Commandsshow username
show username detailshow username <WORD> detail
Description: Show user information
Syntax:
User nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show username <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1947
S Commandsshow username detail
show versionshow version
Description: Show version information
Command Mode: exec : Exec Mode
Command Path:
# show version
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1948
S Commandsshow version
show vlan-domainshow vlan-domain [name <arg>] [vlan] [leaf <arg>] [detail]
Description: Show command for vlan-domain
Syntax:
(Optional) Vlan-domain namearg
(Optional) VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19<vlan-range>
(Optional) Leaf id. Number range from=101 to=4000arg
(Optional) vlan-domain in detail with concrete MOsdetail
Command Mode: exec : Exec Mode
Command Path:
# show vlan-domain [name <>] [vlan] [leaf <>] [detail]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1949
S Commandsshow vlan-domain
show vmm internal debugshow vmm internal debug
Description: Show vmm debug information
Command Mode: exec : Exec Mode
Command Path:
# show vmm internal debug
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1950
S Commandsshow vmm internal debug
show vmm internal debug epgshow vmm internal debug epg tenant <tenantName> application <applicationName> epg <epgName>
Description: Show vmm EPg debug information
Syntax:
tenant-nametenant
tenant-name<tenantName>
application-nameapplication
application-name<applicationName>
epg-nameepg
epg-name<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show vmm internal debug epg tenant <tenantName> application <applicationName> epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1951
S Commandsshow vmm internal debug epg
show vmm internal debug macshow vmm internal debug mac <macAddress>
Description: Show vmm mac address debug information
Syntax:
mac-address<macAddress>
Command Mode: exec : Exec Mode
Command Path:
# show vmm internal debug mac <macAddress>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1952
S Commandsshow vmm internal debug mac
show vmware domainshow vmware domain
Description: Show VMware domain information
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1953
S Commandsshow vmware domain
show vmware domain nameshow vmware domain name <name>
Description: VMware domain name
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1954
S Commandsshow vmware domain name
show vmware domain name epgshow vmware domain name <name> epg
Description: Show VMware domain EPG details
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> epg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1955
S Commandsshow vmware domain name epg
show vmware domain name esxshow vmware domain name <name> esx <esx-ip>
Description: Show VMware ESX information
Syntax:
VMware domain name<name>
ESX IP<esx-ip>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> esx <esx-ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1956
S Commandsshow vmware domain name esx
show vmware domain name port-groupshow vmware domain name <name> port-group
Description: Show VMware port group information
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> port-group
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1957
S Commandsshow vmware domain name port-group
show vmware domain name trunk-portgroupshow vmware domain name <name> trunk-portgroup [name <name>]
Description: Show VMware domain trunk portgroup details
Syntax:
VMware domain name<name>
(Optional) trunk portgroup name<name>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> trunk-portgroup [name <name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1958
S Commandsshow vmware domain name trunk-portgroup
show vmware domain name vcentershow vmware domain name <name> vcenter <hostname|ip>
Description: VMware vCenter ip or hostname
Syntax:
VMware domain name<name>
vCenter hostname or IP<hostname|ip>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> vcenter <hostname|ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1959
S Commandsshow vmware domain name vcenter
show vmware domain name vmshow vmware domain name <name> vm
Description: Show VMware VM information
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> vm
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1960
S Commandsshow vmware domain name vm
show vmware domain name vm nameshow vmware domain name <name> vm name <vm-name>
Description: Show detailed VMware VM information
Syntax:
VMware domain name<name>
VM Name<vm-name>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> vm name <vm-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1961
S Commandsshow vmware domain name vm name
show vmware vmshow vmware vm [name <WORD>] [ip <A.B.C.D>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Description: Show VMware VM information
Syntax:
(Optional) Specify a VM nameWORD
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: exec : Exec Mode
Command Path:
# show vmware vm [name <WORD>] [ip <A.B.C.D>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1962
S Commandsshow vmware vm
show vpcshow vpc map <vpc-list>
Description: Show vpc mapping
Syntax:
Map by namemap
vpc names<vpc-list>
Command Mode: exec : Exec Mode
Command Path:
# show vpc map <vpc-list>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1963
S Commandsshow vpc
show vpc map leafshow vpc map <vpc-list> leaf WORD [fex <NUMBER>]
Description: Leaf
Syntax:
Map by namemap
vpc names<vpc-list>
Leaf Range or Leaf Name ListWORD
(Optional) Fex ID. Number range from=101 to=164<101-164>
Command Mode: exec : Exec Mode
Command Path:
# show vpc map <vpc-list> leaf WORD [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1964
S Commandsshow vpc map leaf
show vrfshow vrf WORD
Description: Show VRF Information
Syntax:
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1965
S Commandsshow vrf
show vrf detailshow vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1966
S Commandsshow vrf detail
show vsan-domainshow vsan-domain [name <arg>] [detail]
Description: Show command for vsan-domain
Syntax:
(Optional) Vsan-domain namearg
(Optional) Vsan-domain detailed informationdetail
Command Mode: exec : Exec Mode
Command Path:
# show vsan-domain [name <>] [detail]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1967
S Commandsshow vsan-domain
shutshut
Description: Disable BFD
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# shut
shut
Description: Disable BFD
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# shut
shut
Description: Disable monitor session
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# shut
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1968
S Commandsshut
shutdownshutdown
Description: Administrative state of the Policer
Command Mode: policy-map type data-plane : Create a policymap of DataPlane type to police/reclassifythe traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# shutdown
shutdown
Description: Disable the class of service specified
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# shutdown
shutdown
Description: Set admin state to disabled
Command Mode: switchport port-authentication : Port authentication configuration
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# switchport port-authentication <WORD>(config-port-authentication)# shutdown
shutdown
Description: Administrative state of the Policer
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# shutdown
shutdown
Description: dscp-map toggling
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1969
S Commandsshutdown
Command Mode: qos : Set DSCP Class translation values
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# qos dscp-map <WORD>(config-qos-cmap)# shutdown
shutdown
Description: Disable Interface
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# shutdown
shutdown
Description: Disable Port Channel
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# shutdown
shutdown
Description: Disable Interface
Command Mode: interface vfc : Virtual Fiber Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vfc <ifRange>(config-leaf-if)# shutdown
shutdown
Description: Disable Interface
Command Mode: interface vfc-po : VFC Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vfc-po <WORD> [fex <fex>](config-leaf-if)# shutdown
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1970
S Commandsshutdown
shutdown
Description: Disable Interface
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# shutdown
shutdown
Description: Disable Port Channel
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# shutdown
shutdown
Description: Disable Interface
Command Mode: interface vfc : Virtual Fiber Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vfc <ifRange>(config-leaf-if)# shutdown
shutdown
Description: Disable Interface
Command Mode: interface vfc-po : VFC Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vfc-po <WORD> [fex <fex>](config-leaf-if)# shutdown
shutdown
Description: Disable interface
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1971
S Commandsshutdown
(config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# shutdown
shutdown
Description: Disable monitor session
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# shutdown
shutdown
Description: Disable monitor session
Command Mode: monitor fabric : Configue monitor session for fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# shutdown
shutdown
Description: Disable monitor session
Command Mode: monitor tenant : Configue monitor session for tenant EPGs
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <WORD>(config-monitor-tenant)# shutdown
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1972
S Commandsshutdown
site-idsite-id <WORD>
Description: ID of the network where the site is deployed
Syntax:
The site id (Max Size 512) surrounded by quotesWORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# site-id <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1973
S Commandssite-id
slow-drain congestion-timeout actionslow-drain congestion-timeout action err-disable|log
Description: Configure congestion action
Syntax:
Error disableerr-disable
Sysloglog
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# slow-drain congestion-timeout action err-disable|log
slow-drain congestion-timeout action err-disable|log
Description: Configure congestion action
Syntax:
Error disableerr-disable
Sysloglog
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# slow-drain congestion-timeout action err-disable|log
slow-drain congestion-timeout action err-disable|log
Description: Configure congestion action
Syntax:
Error disableerr-disable
Sysloglog
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1974
S Commandsslow-drain congestion-timeout action
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# slow-drain congestion-timeout action err-disable|log
slow-drain congestion-timeout action err-disable|log
Description: Configure congestion action
Syntax:
Error disableerr-disable
Sysloglog
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# slow-drain congestion-timeout action err-disable|log
slow-drain congestion-timeout action err-disable|log
Description: Configure congestion action
Syntax:
Error disableerr-disable
Sysloglog
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# slow-drain congestion-timeout action err-disable|log
slow-drain congestion-timeout action err-disable|log
Description: Configure congestion action
Syntax:
Error disableerr-disable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1975
S Commandsslow-drain congestion-timeout action
Sysloglog
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# slow-drain congestion-timeout action err-disable|log
slow-drain congestion-timeout action err-disable|log
Description: Configure congestion action
Syntax:
Error disableerr-disable
Sysloglog
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# slow-drain congestion-timeout action err-disable|log
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1976
S Commandsslow-drain congestion-timeout action
slow-drain congestion-timeout countslow-drain congestion-timeout count <NUMBER>
Description: Configure number of pause frames per second
Syntax:
Configure number of pause frames per second. Number range from=1to=10000
<range>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# slow-drain congestion-timeout count <NUMBER>
slow-drain congestion-timeout count <NUMBER>
Description: Configure number of pause frames per second
Syntax:
Configure number of pause frames per second. Number range from=1to=10000
<range>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# slow-drain congestion-timeout count <NUMBER>
slow-drain congestion-timeout count <NUMBER>
Description: Configure number of pause frames per second
Syntax:
Configure number of pause frames per second. Number range from=1to=10000
<range>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1977
S Commandsslow-drain congestion-timeout count
(config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# slow-drain congestion-timeout count <NUMBER>
slow-drain congestion-timeout count <NUMBER>
Description: Configure number of pause frames per second
Syntax:
Configure number of pause frames per second. Number range from=1to=10000
<range>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# slow-drain congestion-timeout count <NUMBER>
slow-drain congestion-timeout count <NUMBER>
Description: Configure number of pause frames per second
Syntax:
Configure number of pause frames per second. Number range from=1to=10000
<range>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# slow-drain congestion-timeout count <NUMBER>
slow-drain congestion-timeout count <NUMBER>
Description: Configure number of pause frames per second
Syntax:
Configure number of pause frames per second. Number range from=1to=10000
<range>
Command Mode: interface port-channel : Port Channel interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1978
S Commandsslow-drain congestion-timeout count
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# slow-drain congestion-timeout count <NUMBER>
slow-drain congestion-timeout count <NUMBER>
Description: Configure number of pause frames per second
Syntax:
Configure number of pause frames per second. Number range from=1to=10000
<range>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# slow-drain congestion-timeout count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1979
S Commandsslow-drain congestion-timeout count
slow-drain pauseslow-drain pause timeout <NUMBER>
Description: Configure pause frame timeout
Syntax:
Configure pause frame timeouttimeout
Configure pause timeout in milliseconds. Number range from=100to=1000
<interval>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# slow-drain pause timeout <NUMBER>
slow-drain pause timeout <NUMBER>
Description: Configure pause frame timeout
Syntax:
Configure pause frame timeouttimeout
Configure pause timeout in milliseconds. Number range from=100to=1000
<interval>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# slow-drain pause timeout <NUMBER>
slow-drain pause timeout <NUMBER>
Description: Configure pause frame timeout
Syntax:
Configure pause frame timeouttimeout
Configure pause timeout in milliseconds. Number range from=100to=1000
<interval>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1980
S Commandsslow-drain pause
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# slow-drain pause timeout <NUMBER>
slow-drain pause timeout <NUMBER>
Description: Configure pause frame timeout
Syntax:
Configure pause frame timeouttimeout
Configure pause timeout in milliseconds. Number range from=100to=1000
<interval>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# slow-drain pause timeout <NUMBER>
slow-drain pause timeout <NUMBER>
Description: Configure pause frame timeout
Syntax:
Configure pause frame timeouttimeout
Configure pause timeout in milliseconds. Number range from=100to=1000
<interval>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# slow-drain pause timeout <NUMBER>
slow-drain pause timeout <NUMBER>
Description: Configure pause frame timeout
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1981
S Commandsslow-drain pause
Syntax:
Configure pause frame timeouttimeout
Configure pause timeout in milliseconds. Number range from=100to=1000
<interval>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# slow-drain pause timeout <NUMBER>
slow-drain pause timeout <NUMBER>
Description: Configure pause frame timeout
Syntax:
Configure pause frame timeouttimeout
Configure pause timeout in milliseconds. Number range from=100to=1000
<interval>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# slow-drain pause timeout <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1982
S Commandsslow-drain pause
slow-timerslow-timer <NUMBER>
Description: Configure BFD SLOW-TIMER value in milliseconds
Syntax:
BFD interval. Number range from=1000 to=30000<interval>
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# slow-timer <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1983
S Commandsslow-timer
snapshot downloadsnapshot download <WORD>
Description: Configuration snapshot download setup mode
Syntax:
Snapshot downloader nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# snapshot download <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1984
S Commandssnapshot download
snapshot exportsnapshot export <WORD>
Description: Configuration export setup mode
Syntax:
Export configuration nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# snapshot export <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1985
S Commandssnapshot export
snapshot importsnapshot import <WORD>
Description: Configuration import setup mode
Syntax:
Import configuration nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# snapshot import <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1986
S Commandssnapshot import
snapshot rollbacksnapshot rollback <WORD>
Description: Configuration rollback setup mode
Syntax:
Rollback configuration nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# snapshot rollback <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1987
S Commandssnapshot rollback
snapshot uploadsnapshot upload <WORD>
Description: Configuration snapshot upload setup mode
Syntax:
Snapshot uploader nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# snapshot upload <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1988
S Commandssnapshot upload
snmp-server clientgroupsnmp-server clientgroup <group-name> [management-epg <mgmt-epg>] [client <ip-address/hostname>]
Description: Configure SNMP client-group
Syntax:
SNMP clientgroup<group-name>
(Optional) Management EPG (default: oob-default)<mgmt-epg>
(Optional) Ip-address/hostname of the snmp client<ip-address/hostname>
Command Mode: template snmp-fabric : Simple Network Management Protocol (SNMP)
Command Path:
# configure [['terminal', 't']](config)# template snmp-fabric <WORD>(config-template-snmp-fabric)# snmp-server clientgroup <group-name> [management-epg<mgmt-epg>] [client <ip-address/hostname>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1989
S Commandssnmp-server clientgroup
snmp-server communitysnmp-server community <community-name>
Description: Configure SNMP community
Syntax:
SNMP community<community-name>
Command Mode: template snmp-fabric : Simple Network Management Protocol (SNMP)
Command Path:
# configure [['terminal', 't']](config)# template snmp-fabric <WORD>(config-template-snmp-fabric)# snmp-server community <community-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1990
S Commandssnmp-server community
snmp-server contactsnmp-server contact <contact-name>
Description: Configure SNMP contact
Syntax:
SNMP contact name<contact-name>
Command Mode: template snmp-fabric : Simple Network Management Protocol (SNMP)
Command Path:
# configure [['terminal', 't']](config)# template snmp-fabric <WORD>(config-template-snmp-fabric)# snmp-server contact <contact-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1991
S Commandssnmp-server contact
snmp-server hostsnmp-server host <ip-address/hostname> traps-version 1|2c|3 <community> auth|none|priv [udp-port <port>][management-epg <mgmt-epg>]
Description: Configure SNMP trap host
Syntax:
Ip-address/hostname of the snmp trap destination<ip-address/hostname>
SNMP Version to use for trapstraps-version
Use SNMPv11
Use SNMPv22c
Use SNMPv33
SNMP community/security<community>
Use Authentication Onlyauth
Use No Authenticationnone
Use Authentication and Encryptionpriv
(Optional) UDP port for traps (default 162)<port>
(Optional) Management EPG (default: oob-default)<mgmt-epg>
Command Mode: template snmp-fabric : Simple Network Management Protocol (SNMP)
Command Path:
# configure [['terminal', 't']](config)# template snmp-fabric <WORD>(config-template-snmp-fabric)# snmp-server host <ip-address/hostname> traps-version 1|2c|3<community> auth|none|priv [udp-port <port>] [management-epg <mgmt-epg>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1992
S Commandssnmp-server host
snmp-server locationsnmp-server location <location-name>
Description: Configure SNMP location
Syntax:
SNMP location<location-name>
Command Mode: template snmp-fabric : Simple Network Management Protocol (SNMP)
Command Path:
# configure [['terminal', 't']](config)# template snmp-fabric <WORD>(config-template-snmp-fabric)# snmp-server location <location-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1993
S Commandssnmp-server location
snmp-server protocolsnmp-server protocol enable
Description: Enable SNMP protocol
Syntax:
Enable SNMP protocolenable
Command Mode: template snmp-fabric : Simple Network Management Protocol (SNMP)
Command Path:
# configure [['terminal', 't']](config)# template snmp-fabric <WORD>(config-template-snmp-fabric)# snmp-server protocol enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1994
S Commandssnmp-server protocol
snmp-server usersnmp-server user <user-name> auth sha|md5 priv aes|des|none
Description: Configure SNMP user
Syntax:
SNMP user<user-name>
Authentication Typeauth
Use HMAC SHA algorithm for authenticationsha
Use HMAC MD5 algorithm for authenticationmd5
Privacy Typepriv
Use 128-bit AES algorithm for privacyaes
Use 64-bit DES algorithm for privacydes
Do not use privacynone
Command Mode: template snmp-fabric : Simple Network Management Protocol (SNMP)
Command Path:
# configure [['terminal', 't']](config)# template snmp-fabric <WORD>(config-template-snmp-fabric)# snmp-server user <user-name> auth sha|md5 priv aes|des|none
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1995
S Commandssnmp-server user
source-guard-admin-statussource-guard-admin-status enabled-both|disabled
Description: Config source guard administrative status in first hop security bridge domain policy
Syntax:
Enable source guard for both IPv4 and IPv6enabled-both
Disable source guarddisabled
Command Mode: security-policy : Configuration for security policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# first-hop-security(config-tenant-fhs)# security-policy <WORD>(config-tenant-fhs-secpol)# source-guard-admin-status enabled-both|disabled
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1996
S Commandssource-guard-admin-status
sourcesource address <A.B.C.D|A:B::C:D/LEN>
Description: Configure source
Syntax:
IP Addressaddress
Source of the exporter in format x.x.x.x|x::x/m. Recommended to containroom for at least 12 host bits
A.B.C.D|A:B::C:D/LEN
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transportudp <dstPort>(config-tn-flow-exporter)# source address <A.B.C.D|A:B::C:D/LEN>
source address <A.B.C.D|A:B::C:D/LEN>
Description: Configure source
Syntax:
IP Addressaddress
Source of the exporter in format x.x.x.x|x::x/m. Recommended to containroom for at least 12 host bits
A.B.C.D|A:B::C:D/LEN
Command Mode: flow exporter : Configure Netflow Exporter
Command Path:
# configure [['terminal', 't']](config)# flow exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-exporter)# source address <A.B.C.D|A:B::C:D/LEN>
source address <A.B.C.D|A:B::C:D/LEN>
Description: Configure source
Syntax:
IP Addressaddress
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1997
S Commandssource
Source of the exporter in format x.x.x.x|x::x/m. Recommended to containroom for at least 12 host bits
A.B.C.D|A:B::C:D/LEN
Command Mode: flow vm-exporter : Configure NetFlow Exporter for VM Networking
Command Path:
# configure [['terminal', 't']](config)# flow vm-exporter <WORD> destination address <A.B.C.D or A:B::C:D> transport udp<dstPort>(config-flow-vm-exporter)# source address <A.B.C.D|A:B::C:D/LEN>
source tenant <WORD> application <WORD> epg <WORD> [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Description: Configure monitor virtual source
Syntax:
tenanttenant
tenant name (Max Size 63)WORD
applicationapplication
application name (Max Size 64)WORD
epgepg
epg name (Max Size 64)WORD
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# source tenant <WORD> application <WORD> epg <WORD> [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)1998
S Commandssource
source applicationsource application <application_name> epg <epg_name>
Description: Configure EPG as monitor source
Syntax:
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
Command Mode: monitor tenant : Configue monitor session for tenant EPGs
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <WORD>(config-monitor-tenant)# source application <application_name> epg <epg_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 1999
S Commandssource application
source interface ethernetsource interface ethernet <ethernet> leaf <leaf Id>
Description: Configure monitor for ethernet access interfaces
Syntax:
List of ethernet itfs<ethernet>
leafleaf
leaf Id<leaf Id>
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface ethernet <ethernet> leaf <leaf Id>
source interface ethernet <ethernet> switch <switch Id>
Description: Configure monitor for ethernet fabric interfaces
Syntax:
ethernet interface range<ethernet>
switchswitch
switch Id<switch Id>
Command Mode: monitor fabric : Configue monitor session for fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2000
S Commandssource interface ethernet
source interface port-channelsource interface port-channel <port-channel list> leaf <leaf Id> [fex <fex Id>]
Description: Configure monitor for port-channel interfaces
Syntax:
<port-channel list><port-channel list>
leafleaf
leaf Id<leaf Id>
(Optional) fex Id<fex Id>
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface port-channel <port-channel list> leaf <leaf Id>[fex <fex Id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2001
S Commandssource interface port-channel
source interface vpcsource interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex <fex Ids>]
Description: Configure monitor for VPC interfaces
Syntax:
<vpc list><vpc list>
leafleaf
leaf Id1<leaf Id1>
leaf Id2<leaf Id2>
(Optional) paired fex Ids<fex Ids>
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex<fex Ids>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2002
S Commandssource interface vpc
spanning-treespanning-tree mst configuration
Description: STP MST configuration mode
Syntax:
Multiple spanning treemst
Configure multiple spanning tree protocolconfiguration
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration
spanning-tree
Description: Add spanning tree
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# spanning-tree
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Enable or Disable BPDU filter/guard
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2003
S Commandsspanning-tree
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Enable BPDU filter/guard
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Enable or disable BPDU filter/guard
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Enable BPDU filter/guard
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2004
S Commandsspanning-tree
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Enable or disable BPDU filter/guard
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Enable BPDU filter/guard
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2005
S Commandsspanning-tree
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Spanning Tree Subsystem
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2006
S Commandsspanning-tree
spanning-tree bpdu-filterspanning-tree bpdu-filter enable|disable|default
Description: Configure BPDU filter override on AVS uplink ports
Syntax:
Enable BPDU filterenable
Disable BPDU filterdisable
Remove BPDU filter/guard override policydefault
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# spanning-tree bpdu-filter enable|disable|default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2007
S Commandsspanning-tree bpdu-filter
spanning-tree bpdu-guardspanning-tree bpdu-guard enable|disable|default
Description: Configure BPDU guard override on AVS uplink ports
Syntax:
Enable BPDU guardenable
Disable BPDU guarddisable
Remove BPDU filter/guard override policydefault
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# spanning-tree bpdu-guard enable|disable|default
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2008
S Commandsspanning-tree bpdu-guard
speedspeed <interfaceSpeed>
Description: Configure Interface Speed
Syntax:
Interface Speed Policy<interfaceSpeed>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# speed <interfaceSpeed>
speed <portChannelSpeed>
Description: Configure Interface Speed
Syntax:
Port-Channel Speed Policy<portChannelSpeed>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# speed <portChannelSpeed>
speed <interfaceSpeed>
Description: Configure Interface Speed
Syntax:
Interface Speed Policy<interfaceSpeed>
Command Mode: template spine-interface-policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template spine-interface-policy-group <WORD>(config-spine-if-pol-grp)# speed <interfaceSpeed>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2009
S Commandsspeed
speed <interfaceSpeed>
Description: Configure Interface Speed
Syntax:
Interface Speed Policy<interfaceSpeed>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# speed <interfaceSpeed>
speed <speed>
Description: Configure Interface Speed
Syntax:
Speed Value<speed>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# speed <speed>
speed <interfaceSpeed>
Description: Configure Interface Speed
Syntax:
Interface Speed Policy<interfaceSpeed>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# speed <interfaceSpeed>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2010
S Commandsspeed
speed <speed>
Description: Configure Interface Speed
Syntax:
Speed Value<speed>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# speed <speed>
speed <speed>
Description: Configure Interface Speed
Syntax:
Interface Speed Policy<speed>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# speed <speed>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2011
S Commandsspeed
spf-intervalspf-interval level-1 <NUMBER> <50-120000> <50-120000>
Description: Set the ISIS SPF maximal wait interval
Syntax:
Level 1level-1
SPF maximum wait interval. Number range from=50 to=120000<50-120000>
Initial and secondary wait intervals (both values are required)<50-120000> <50-120000>
Command Mode: isis : Intermediate System to Intermediate System (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# pod <NUMBER>(config-pod)# isis fabric(config-pod-isis)# spf-interval level-1 <NUMBER> <50-120000> <50-120000>
spf-interval level-1 <NUMBER> <50-120000> <50-120000>
Description: Set the ISIS SPF maximal wait interval
Syntax:
Level 1level-1
SPF maximum wait interval. Number range from=50 to=120000<50-120000>
Initial and secondary wait intervals (both values are required)<50-120000> <50-120000>
Command Mode: template isis-fabric : InterSystem-InterSystem Protocol (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# template isis-fabric <WORD>(config-template-isis-fabric)# spf-interval level-1 <NUMBER> <50-120000> <50-120000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2012
S Commandsspf-interval
spine-groupspine-group <WORD>
Description: Configure Spine Group
Syntax:
Spine Group name (Max Size 64)WORD
Command Mode: spine-profile : Configure Spine Profile
Command Path:
# configure [['terminal', 't']](config)# spine-profile <WORD>(config-spine-profile)# spine-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2013
S Commandsspine-group
spine-interface-groupspine-interface-group <WORD>
Description: Configure Spine Interface Group
Syntax:
Spine Interface Group name (Max Size 64)WORD
Command Mode: spine-interface-profile : Create Spine Interface Profile
Command Path:
# configure [['terminal', 't']](config)# spine-interface-profile <WORD>(config-spine-if-profile)# spine-interface-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2014
S Commandsspine-interface-group
spine-interface-policy-groupspine-interface-policy-group <WORD>
Description: Associate an Interface Policy Group to this Interface Group
Syntax:
Spine Interface Policy Group Name (Max Size 64)WORD
Command Mode: spine-interface-group : Configure Spine Interface Group
Command Path:
# configure [['terminal', 't']](config)# spine-interface-profile <WORD>(config-spine-if-profile)# spine-interface-group <WORD>(config-spine-if-group)# spine-interface-policy-group <WORD>
spine-interface-policy-group <WORD> [force]
Description: Configure Spine Interface Policy Group
Syntax:
Spine Interface Policy Group Name (Max Size 64)WORD
(Optional) Delete Per Port Configuration and applyspine-interface-policy-group config
force
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# spine-interface-policy-group <WORD> [force]
spine-interface-policy-group <WORD> [force]
Description: Configure Spine Interface Policy Group
Syntax:
Spine Interface Policy Group Name (Max Size 64)WORD
(Optional) Delete Per Port Configuration and applyspine-interface-policy-group config
force
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2015
S Commandsspine-interface-policy-group
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# spine-interface-policy-group <WORD> [force]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2016
S Commandsspine-interface-policy-group
spine-interface-profilespine-interface-profile <WORD>
Description: Attach Spine Interface Profile to the Spine Profile
Syntax:
Spine Interface Profile name (Max Size 64)WORD
Command Mode: spine-profile : Configure Spine Profile
Command Path:
# configure [['terminal', 't']](config)# spine-profile <WORD>(config-spine-profile)# spine-interface-profile <WORD>
spine-interface-profile <WORD>
Description: Create Spine Interface Profile
Syntax:
Spine Interface Profile name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# spine-interface-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2017
S Commandsspine-interface-profile
spine-policy-groupspine-policy-group <WORD>
Description: Configure spine policy group
Syntax:
spine policy name (Max Size 64)WORD
Command Mode: spine-group : Configure Spine Group
Command Path:
# configure [['terminal', 't']](config)# spine-profile <WORD>(config-spine-profile)# spine-group <WORD>(config-spine-group)# spine-policy-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2018
S Commandsspine-policy-group
spine-profilespine-profile <WORD>
Description: Configure Spine Profile
Syntax:
Spine Profile name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# spine-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2019
S Commandsspine-profile
spinespine <101-4000>
Description: Provide a Range of Nodes
Syntax:
Spine Range or Spine Name List<101-4000>
Command Mode: spine-group : Configure Spine Group
Command Path:
# configure [['terminal', 't']](config)# spine-profile <WORD>(config-spine-profile)# spine-group <WORD>(config-spine-group)# spine <101-4000>
spine <101-4000>
Description: Configure Spine Node
Syntax:
Spine Range or Spine Name List<101-4000>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2020
S Commandsspine
ssh-keyssh-key <WORD>
Description: Update ssh key for the user for ssh authentication
Syntax:
A name for SSH key (Max Size 64)WORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# ssh-key <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2021
S Commandsssh-key
ssh-servicessh-service
Description: SSH communication policy group
Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# ssh-service
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2022
S Commandsssh-service
ssl-protocolsssl-protocols <sslProtocols>
Description: Set the SSL protocol (comma separated values)
Syntax:
SSL Protocols as comma separated values like val1,val2,..valNsslProtocols
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# ssl-protocols <sslProtocols>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2023
S Commandsssl-protocols
ssl-validation-levelssl-validation-level <ssl-validation-level>
Description: Set the LDAP Server SSL Certificate validation level
Syntax:
<ssl-validation-level><ssl-validation-level>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# ssl-validation-level <ssl-validation-level>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2024
S Commandsssl-validation-level
statestate <WORD>
Description: Set The state or province in which the organization is located.
Syntax:
state or province (Max Size 64)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# state <WORD>
state <cipherState>
Description: Cipher state
Syntax:
Cipher state as comma separated values like val1,val2,..valNcipherState
Command Mode: ciphers : HTTPS cipher suite
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# ciphers <WORD>(config-ciphers)# state <cipherState>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2025
S Commandsstate
static-endpointstatic-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip<A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure Silent Host behind an EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip<A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure silent Host behind an EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2026
S Commandsstatic-endpoint
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip<A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure Silent Host behind an EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2027
S Commandsstatic-endpoint
(config-spine)# interface ethernet <ifRange>(config-leaf-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip<A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure silent Host behind an EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip<A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure silent Host behind a EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2028
S Commandsstatic-endpoint
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2029
S Commandsstatic-endpoint
static-tepstatic-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>
Description: Configure a static Tunnel Endpoint behind an EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
VLAN range. Number range from=1 to=4094<1-4094>
IP address in format i.i.i.iA.B.C.D
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> <A.B.C.D>
static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>
Description: Configure a static Tunnel Endpoint behind an EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2030
S Commandsstatic-tep
VLAN range. Number range from=1 to=4094<1-4094>
IP address in format i.i.i.iA.B.C.D
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> <A.B.C.D>
static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>
Description: Configure a static Tunnel Endpoint behind an EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
VLAN range. Number range from=1 to=4094<1-4094>
IP address in format i.i.i.iA.B.C.D
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> <A.B.C.D>
static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>
Description: Configure a static Tunnel Endpoint behind an EPG with a Static Path Attachment
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2031
S Commandsstatic-tep
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
VLAN range. Number range from=1 to=4094<1-4094>
IP address in format i.i.i.iA.B.C.D
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> <A.B.C.D>
static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>
Description: Configure a static Tunnel Endpoint behind a EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
VLAN range. Number range from=1 to=4094<1-4094>
IP address in format i.i.i.iA.B.C.D
Command Mode: interface : Provide VPC Name
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2032
S Commandsstatic-tep
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2033
S Commandsstatic-tep
statisticsstatistics enable
Description: Enable/disable stats collection on vCenter
Syntax:
enableenable
Command Mode: vcenter : Configure a vCenter in the VMware domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# statistics enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2034
S Commandsstatistics
storm-control broadcast levelstorm-control broadcast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for broadcast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control broadcast level <0-100> [burst-rate <0-100>]
storm-control broadcast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for broadcast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# storm-control broadcast level <0-100> [burst-rate <0-100>]
storm-control broadcast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for broadcast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2035
S Commandsstorm-control broadcast level
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control broadcast level <0-100> [burst-rate <0-100>]
storm-control broadcast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for broadcast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control broadcast level <0-100> [burst-rate <0-100>]
storm-control broadcast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for broadcast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# storm-control broadcast level <0-100> [burst-rate <0-100>]
storm-control broadcast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for broadcast
Syntax:
Rate of Bandwidth in Percentage<0-100>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2036
S Commandsstorm-control broadcast level
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control broadcast level <0-100> [burst-rate <0-100>]
storm-control broadcast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for broadcast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control broadcast level <0-100> [burst-rate <0-100>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2037
S Commandsstorm-control broadcast level
storm-control broadcast ppsstorm-control broadcast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for broadcast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control broadcast pps <> burst-rate <>
storm-control broadcast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for broadcast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# storm-control broadcast pps <> burst-rate <>
storm-control broadcast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for broadcast
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2038
S Commandsstorm-control broadcast pps
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control broadcast pps <> burst-rate <>
storm-control broadcast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for broadcast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control broadcast pps <> burst-rate <>
storm-control broadcast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for broadcast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2039
S Commandsstorm-control broadcast pps
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# storm-control broadcast pps <> burst-rate <>
storm-control broadcast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for broadcast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control broadcast pps <> burst-rate <>
storm-control broadcast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for broadcast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control broadcast pps <> burst-rate <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2040
S Commandsstorm-control broadcast pps
storm-control levelstorm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for all packet types
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control level <0-100> [burst-rate <0-100>]
storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for all packet types
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# storm-control level <0-100> [burst-rate <0-100>]
storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for all packet types
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2041
S Commandsstorm-control level
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control level <0-100> [burst-rate <0-100>]
storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for all packet types
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control level <0-100> [burst-rate <0-100>]
storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for all packet types
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# storm-control level <0-100> [burst-rate <0-100>]
storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for all packet types
Syntax:
Rate of Bandwidth in Percentage<0-100>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2042
S Commandsstorm-control level
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control level <0-100> [burst-rate <0-100>]
storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for all packet types
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control level <0-100> [burst-rate <0-100>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2043
S Commandsstorm-control level
storm-control multicast levelstorm-control multicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for multicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control multicast level <0-100> [burst-rate <0-100>]
storm-control multicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for multicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# storm-control multicast level <0-100> [burst-rate <0-100>]
storm-control multicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for multicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2044
S Commandsstorm-control multicast level
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control multicast level <0-100> [burst-rate <0-100>]
storm-control multicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for multicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control multicast level <0-100> [burst-rate <0-100>]
storm-control multicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for multicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# storm-control multicast level <0-100> [burst-rate <0-100>]
storm-control multicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for multicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2045
S Commandsstorm-control multicast level
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control multicast level <0-100> [burst-rate <0-100>]
storm-control multicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for multicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control multicast level <0-100> [burst-rate <0-100>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2046
S Commandsstorm-control multicast level
storm-control multicast ppsstorm-control multicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for multicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control multicast pps <> burst-rate <>
storm-control multicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for multicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# storm-control multicast pps <> burst-rate <>
storm-control multicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for multicast
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2047
S Commandsstorm-control multicast pps
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control multicast pps <> burst-rate <>
storm-control multicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for multicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control multicast pps <> burst-rate <>
storm-control multicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for multicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2048
S Commandsstorm-control multicast pps
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# storm-control multicast pps <> burst-rate <>
storm-control multicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for multicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control multicast pps <> burst-rate <>
storm-control multicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for multicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control multicast pps <> burst-rate <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2049
S Commandsstorm-control multicast pps
storm-control ppsstorm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for all packet types
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control pps <> burst-rate <>
storm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for all packet type
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# storm-control pps <> burst-rate <>
storm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for all packet types
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2050
S Commandsstorm-control pps
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control pps <> burst-rate <>
storm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for all packet types
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control pps <> burst-rate <>
storm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for all packet types
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2051
S Commandsstorm-control pps
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# storm-control pps <> burst-rate <>
storm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for all packet types
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control pps <> burst-rate <>
storm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for all packets type
Syntax:
Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control pps <> burst-rate <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2052
S Commandsstorm-control pps
storm-control unicast levelstorm-control unicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for unicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control unicast level <0-100> [burst-rate <0-100>]
storm-control unicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for unicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# storm-control unicast level <0-100> [burst-rate <0-100>]
storm-control unicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for unicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2053
S Commandsstorm-control unicast level
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control unicast level <0-100> [burst-rate <0-100>]
storm-control unicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for unicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control unicast level <0-100> [burst-rate <0-100>]
storm-control unicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for unicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# storm-control unicast level <0-100> [burst-rate <0-100>]
storm-control unicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for unicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2054
S Commandsstorm-control unicast level
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control unicast level <0-100> [burst-rate <0-100>]
storm-control unicast level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) for unicast
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control unicast level <0-100> [burst-rate <0-100>]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2055
S Commandsstorm-control unicast level
storm-control unicast ppsstorm-control unicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for unicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control unicast pps <> burst-rate <>
storm-control unicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for unicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# storm-control unicast pps <> burst-rate <>
storm-control unicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for unicast
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2056
S Commandsstorm-control unicast pps
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control unicast pps <> burst-rate <>
storm-control unicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for unicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control unicast pps <> burst-rate <>
storm-control unicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for unicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2057
S Commandsstorm-control unicast pps
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# storm-control unicast pps <> burst-rate <>
storm-control unicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for unicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control unicast pps <> burst-rate <>
storm-control unicast pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second for unicast
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control unicast pps <> burst-rate <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2058
S Commandsstorm-control unicast pps
street-addressstreet-address <WORD>
Description: Street address of the site
Syntax:
The street address (Max Size 255) surrounded by quotesWORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# street-address <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2059
S Commandsstreet-address
subjectsubject <WORD>
Description: Set The fully qualified domain name or DN of the requesting device.
Syntax:
FQDN or DN of device (Max Size 64)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# subject <WORD>
subject <WORD>
Description: Configuration a subject on the contract
Syntax:
Name of the contract subject (Max Size 64)WORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2060
S Commandssubject
subnetsubnet <WORD>
Description: Configure Private IP Subnet
Syntax:
WORDWORD
Command Mode: l4l7 resource-pool : Configure L4-L7 Service Resource Pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 resource-pool <WORD>(config-resource-pool)# subnet <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2061
S Commandssubnet
summary-addresssummary-address <IP-PREFIX/LEN>
Description: Route summarization
Syntax:
Summarized ipIP-PREFIX/LEN
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# summary-address <IP-PREFIX/LEN>
summary-address <IP-PREFIX/LEN>
Description: Route summarization
Syntax:
Summarized ipIP-PREFIX/LEN
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# summary-address <IP-PREFIX/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2062
S Commandssummary-address
svcredir-polsvcredir-pol tenant <tenant> name <WORD>
Description: Configure Service Redirection Policy for a L4-L7 Graph Connector.
Syntax:
Tenant in which the service redirection policy is availabletenant
Tenant in which the service redirection policy is available<tenant>
Service redirection policy namename
Service redirection policy name (Max Size 64)WORD
Command Mode: connector : Configure Connector for a Service Node
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>] [svcredir <Service Redirection>] [service-type <Service Type>](config-service)# connector <WORD> [cluster-interface <WORD>](config-connector)# svcredir-pol tenant <tenant> name <WORD>
svcredir-pol <WORD>
Description: Configure L4L7 service redirection policy
Syntax:
service redirection policy name (Max Size 64)WORD
Command Mode: tenant : Tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# svcredir-pol <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2063
S Commandssvcredir-pol
switch-groupswitch-group <WORD>
Description: Create switch firmware upgrade policy
Syntax:
switch-group name (Max Size 64)WORD
Command Mode: firmware : Firmware upgrade configuration Mode
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2064
S Commandsswitch-group
switchswitch
Description: Add switches to switch group
Syntax:
arg
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# switch
switch
Description: Configure Leaf Node
Syntax:
arg
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# switch
switch
Description: Add switches to zone
Syntax:
arg
Command Mode: zone : Create zone policy
Command Path:
# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>(config-zone)# switch
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2065
S Commandsswitch
switchingswitching mode vlan|vxlan|vxlan-ns
Description: Configure switching mode.
Syntax:
switching Modemode
VLAN/SW Modevlan
VXLAN/SW Modevxlan
VXLAN/HWModevxlan-ns
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD> [delimiter <WORD>](config-vmware)# configure-avs(config-vmware-avs)# switching mode vlan|vxlan|vxlan-ns
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2066
S Commandsswitching
switchportswitchport
Description: Configure switchport parameters
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport
switchport
Description: Configure switchport parameters
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport
switchport
Description: Configure switchport parameters
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# switchport
switchport
Description: Configure switchport parameters
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport
switchport
Description: Configure switchport parameters
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2067
S Commandsswitchport
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2068
S Commandsswitchport
switchport access vlan tenant applicationswitchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>
switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: template port-channel : Configure Port-Channel Parameters
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2069
S Commandsswitchport access vlan tenant application
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>
switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>
switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2070
S Commandsswitchport access vlan tenant application
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>
switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>
switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Access Vlanvlan
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2071
S Commandsswitchport access vlan tenant application
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>
switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2072
S Commandsswitchport access vlan tenant application
switchport access vlan tenant external-sviswitchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to the L2 Access Interface
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to Acess L2 Interface
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface port-channel : Port Channel interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2073
S Commandsswitchport access vlan tenant external-svi
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to the L2 Access Interface
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to Acess L2 Interface
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2074
S Commandsswitchport access vlan tenant external-svi
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to Acess L2 Interface
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2075
S Commandsswitchport access vlan tenant external-svi
switchport modeswitchport mode <arg>
Description: Configure switchport mode for interface
Syntax:
arg
arg
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# switchport mode <>
switchport mode <arg>
Description: Configure switchport mode for vfc interface
Syntax:
arg
arg
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# switchport mode <>
switchport mode dot1q-tunnel <arg>
Description: Tunnel Configuration
Syntax:
QinQ Tunnel Configurationdot1q-tunnel
arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2076
S Commandsswitchport mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport mode dot1q-tunnel <>
switchport mode dot1q-tunnel <arg>
Description: Tunnel Configuration
Syntax:
QinQ Tunnel Configurationdot1q-tunnel
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport mode dot1q-tunnel <>
switchport mode <arg>
Description: Configure switchport mode for vfc interface
Syntax:
arg
Command Mode: interface vfc : Virtual Fiber Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vfc <ifRange>(config-leaf-if)# switchport mode <>
switchport mode <arg>
Description: Configure switchport mode for vfc interface
Syntax:
arg
Command Mode: interface vfc-po : VFC Port Channel interface
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2077
S Commandsswitchport mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vfc-po <WORD> [fex <fex>](config-leaf-if)# switchport mode <>
switchport mode dot1q-tunnel <arg>
Description: Tunnel Configuration
Syntax:
QinQ Tunnel Configurationdot1q-tunnel
arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# switchport mode dot1q-tunnel <>
switchport mode dot1q-tunnel <arg>
Description: Tunnel Configuration
Syntax:
QinQ Tunnel Configurationdot1q-tunnel
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport mode dot1q-tunnel <>
switchport mode <arg>
Description: Configure switchport mode for vfc interface
Syntax:
arg
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2078
S Commandsswitchport mode
Command Mode: interface vfc : Virtual Fiber Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vfc <ifRange>(config-leaf-if)# switchport mode <>
switchport mode <arg>
Description: Configure switchport mode for vfc interface
Syntax:
arg
Command Mode: interface vfc-po : VFC Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface vfc-po <WORD> [fex <fex>](config-leaf-if)# switchport mode <>
switchport mode <arg>
Description: Configure switchport mode for interface
Syntax:
arg
arg
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport mode <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2079
S Commandsswitchport mode
switchport port-authenticationswitchport port-authentication <WORD>
Description: Port authentication configuration
Syntax:
Port authentication Policy Group Name (Max Size 64)WORD
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# switchport port-authentication <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2080
S Commandsswitchport port-authentication
switchport port-authentication enableswitchport port-authentication enable
Description: Set admin state to enabled
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport port-authentication enable
switchport port-authentication enable
Description: Set admin state to enabled
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# switchport port-authentication enable
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2081
S Commandsswitchport port-authentication enable
switchport port-authentication host-modeswitchport port-authentication host-mode <arg>
Description: Set host mode
Syntax:
Host modearg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport port-authentication host-mode <>
switchport port-authentication host-mode <arg>
Description: Set host mode
Syntax:
Host modearg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# switchport port-authentication host-mode <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2082
S Commandsswitchport port-authentication host-mode
switchport port-security maximumswitchport port-security maximum <count>
Description:
Syntax:
. Number range from=0 to=12000count
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# switchport port-security maximum <count>
switchport port-security maximum <count>
Description:
Syntax:
. Number range from=0 to=12000count
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# switchport port-security maximum <count>
switchport port-security maximum <arg>
Description: Port-security configuration
Syntax:
. Number range from=0 to=12000arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport port-security maximum <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2083
S Commandsswitchport port-security maximum
switchport port-security maximum <arg>
Description: Port-security configuration
Syntax:
. Number range from=0 to=12000arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport port-security maximum <>
switchport port-security maximum <arg>
Description: Port-security configuration
Syntax:
. Number range from=0 to=12000arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# switchport port-security maximum <>
switchport port-security maximum <arg>
Description: Port-security configuration
Syntax:
. Number range from=0 to=12000arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport port-security maximum <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2084
S Commandsswitchport port-security maximum
switchport port-security maximum <arg>
Description: Port-security configuration
Syntax:
. Number range from=0 to=12000arg
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport port-security maximum <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2085
S Commandsswitchport port-security maximum
switchport port-security timeoutswitchport port-security timeout <count>
Description:
Syntax:
. Number range from=60 to=3600count
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# switchport port-security timeout <count>
switchport port-security timeout <count>
Description:
Syntax:
. Number range from=60 to=3600count
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# switchport port-security timeout <count>
switchport port-security timeout <arg>
Description: port-security configuration
Syntax:
. Number range from=60 to=3600arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport port-security timeout <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2086
S Commandsswitchport port-security timeout
switchport port-security timeout <arg>
Description: port-security configuration
Syntax:
. Number range from=60 to=3600arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport port-security timeout <>
switchport port-security timeout <arg>
Description: port-security configuration
Syntax:
. Number range from=60 to=3600arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# switchport port-security timeout <>
switchport port-security timeout <arg>
Description: port-security configuration
Syntax:
. Number range from=60 to=3600arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport port-security timeout <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2087
S Commandsswitchport port-security timeout
switchport port-security timeout <arg>
Description: port-security configuration
Syntax:
. Number range from=60 to=3600arg
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport port-security timeout <>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2088
S Commandsswitchport port-security timeout
switchport port-security violationswitchport port-security violation protect
Description:
Syntax:
protect
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# switchport port-security violation protect
switchport port-security violation protect
Description:
Syntax:
protect
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-po-ch-if)# switchport port-security violation protect
switchport port-security violation protect
Description: Port-security configuration
Syntax:
protect
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport port-security violation protect
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2089
S Commandsswitchport port-security violation
switchport port-security violation protect
Description: Port-security configuration
Syntax:
protect
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport port-security violation protect
switchport port-security violation protect
Description: Port-security configuration
Syntax:
protect
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# switchport port-security violation protect
switchport port-security violation protect
Description: Port-security configuration
Syntax:
protect
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport port-security violation protect
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2090
S Commandsswitchport port-security violation
switchport port-security violation protect
Description: Port-security configuration
Syntax:
protect
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport port-security violation protect
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2091
S Commandsswitchport port-security violation
switchport tenantswitchport tenant <WORD> dot1q-tunnel <WORD>
Description: dot1q-tunnel Configuration
Syntax:
Tenant hosting the EPg (Max Size 63)WORD
Add an dot1q-tunneldot1q-tunnel
Tunnel EPG name (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport tenant <WORD> dot1q-tunnel <WORD>
switchport tenant <WORD> dot1q-tunnel <WORD>
Description: dot1q-tunnel Configuration
Syntax:
Tenant hosting the EPg (Max Size 63)WORD
Add an dot1q-tunneldot1q-tunnel
Tunnel EPG name (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport tenant <WORD> dot1q-tunnel <WORD>
switchport tenant <WORD> dot1q-tunnel <WORD>
Description: dot1q-tunnel Configuration
Syntax:
Tenant hosting the EPg (Max Size 63)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2092
S Commandsswitchport tenant
Add an dot1q-tunneldot1q-tunnel
Tunnel EPG name (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# switchport tenant <WORD> dot1q-tunnel <WORD>
switchport tenant <WORD> dot1q-tunnel <WORD>
Description: dot1q-tunnel Configuration
Syntax:
Tenant hosting the EPg (Max Size 63)WORD
Add an dot1q-tunneldot1q-tunnel
Tunnel EPG name (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport tenant <WORD> dot1q-tunnel <WORD>
switchport tenant <WORD> dot1q-tunnel <WORD>
Description: dot1q-tunnel Configuration
Syntax:
Tenant hosting the EPg (Max Size 63)WORD
Add an dot1q-tunneldot1q-tunnel
Tunnel EPG name (Max Size 64)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2093
S Commandsswitchport tenant
(config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport tenant <WORD> dot1q-tunnel <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2094
S Commandsswitchport tenant
switchport trunk allowed vlan inband-mgmtswitchport trunk allowed vlan <NUMBER> inband-mgmt <A.B.C.D/LEN>
Description: Configure External L2 connectivity to inband Mnaagement
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Gateway IP Address for External Connectivity format x.x.x.x/mA.B.C.D/LEN
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> inband-mgmt <A.B.C.D/LEN>
switchport trunk allowed vlan <NUMBER> inband-mgmt <A.B.C.D/LEN>
Description: Configure External L2 connectivity to inband Mnaagement
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Gateway IP Address for External Connectivity format x.x.x.x/mA.B.C.D/LEN
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# spine <101-4000>(config-spine)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> inband-mgmt <A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1) 2095
S Commandsswitchport trunk allowed vlan inband-mgmt
switchport trunk allowed vlan tenant applicationswitchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD>epg <WORD>
switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: template port-channel : Configure Port-Channel Parameters
Cisco APIC NX-OS Style CLI Command Reference, Release 3.0(1)2096
S Commandsswitchport trunk allowed vlan tenant application
![Index [] › media › pdf › 1118561880-28.pdf · Group Policy, 540–544, 541–542 overview, 540 Automatic Updates Detection Frequency policy, 543 automating Group Policy tasks,](https://static.documents.pub/doc/80x56/5f0e231c7e708231d43dca36/index-a-media-a-pdf-a-1118561880-28pdf-group-policy-540a544-541a542.jpg)
