Date post: | 08-Nov-2014 |
Category: |
Documents |
Upload: | tupelohuney |
View: | 291 times |
Download: | 3 times |
Clamps and Workholding
Band Clamps 182Bar Clamps 181C-Clamps 178 - 180Clamp Accessories 136 - 138Grippers and Pads 168 - 171Horizontal Handle Hold Down Clamps 118 - 121Hydraulic Power Workholding 148 - 155Manual Clamping Systems 156 - 167Pneumatic Clamp Accessories 147Pneumatic Heavy Duty Clamps 142 - 144Pneumatic Hold Down Clamps 139 - 140Pneumatic Straight Line Action Clamps 141Pneumatic Swing Cylinder Clamps 145 - 146Pull Action Latch Clamps 122 - 125Spring Clamps 180Squeeze Action Plier Clamps 134 - 135Straight Line Action Clamps 126 - 133Vertical Handle Hold Down Clamps 112 - 117Vises and Accessories 172 - 177
LIB
RA
RY
LIB
RA
RY
109
0109.qxd 2/23/2010 12:42 PM Page 109
110
WO RKHOLDING SOLUT IONS
If you don’t see the DE-STA-CO products youneed, let us know and we’ll get them for you.
Available from Reid Supply:
• DE-STA-CO Toggle Clamps and Accessories
• DE-STA-CO Plier Clamps
• DE-STA-CO Premium Clamps
• DE-STA-CO Pneumatic Clamps and Accessories
• Superior consultation, innovation, engineering,service and more
Today’s manufacturing challenges are tougher than ever.Regardless of your application, DE-STA-CO offersworkholding and automation solutions to meet your needs.
• DE-STA-CO products are ideal for a wide variety of industries and manufacturing processes
• Flexible workholding selection accommodates all parts, rangingfrom small and delicate to large and heavy
Reid Supply is the largest stocking distributor of DE-STA-CO in North America
0110-111.qxd 2/19/2010 12:14 PM Page 110
A WORLD OF DE-STA-COAT REID SUPPLY
800.253.0421ReidSupply.com
111
0110-111.qxd 2/19/2010 12:15 PM Page 111
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!112
Cla
mp
s an
d W
ork
ho
ldin
g
AA
E
E
D
D1
F
B
H
C C
J
G
VERTICAL HANDLE HOLD-DOWN CLAMPS
See pages 136 and 137 for clamp accessories.
Series TC-2002, 2007, 2010
Now you can save valuable space in all your applications without sacrificing holding capacity or clamp performance. The open “U” barhas a knob on the end to prevent the spindle from slipping off the end of the arm. Unique design delivers greater hand clearance in theopen position, eliminating pinch points and improving safety and ergonomics. Clamp comes complete with ergonomic handle grip, twoflanged washers and spindle assembly (“U” bar models only). All “S” bar models supplied with bolt retainer.
AA
E
E
D
D1
F
B
TC-2002-UB TC-2007-UB TC-2010-UB
H
C C
J
G
TC-2002-STC-2007-STC-2010-S
TC-2002-S
TC-2002-U
TC-2002-UB
Series TC-2002R, 2007R, 2010R
Discount 30 applies.
Cat. No. A B C D D1 E F G H JBar
Opening
HoldingCapacity
Lbs.
PriceEach1-49
TC-2002-SR 4.73 4.17 .95 .90 .50 1.06 1.36 1.52 1.93 .22 85° 600 24.57TC-2002-UBR 5.07 4.17 1.27 .90 .50 .25 1.36 — 1.93 .22 85° 600 26.15TC-2002-UR 4.73 4.17 .95 .90 .50 1.06 1.36 1.52 1.93 .22 85° 600 23.58TC-2007-SR 7.21 5.94 1.25 1.25 .75 1.25 1.93 1.94 2.88 .28 76° 1000 35.05TC-2007-UBR 7.64 5.94 1.68 1.25 .75 .25 1.93 — 2.88 .28 76° 1000 35.81TC-2007-UR 7.21 5.94 1.25 1.25 .75 1.25 1.93 1.94 2.88 .28 76° 1000 34.39TC-2010-SR 9.00 7.28 1.70 1.25 — 1.78 2.53 2.62 3.56 .34 83° 1400 47.55TC-2010-UR 9.00 7.28 1.70 1.25 — 1.78 2.53 2.62 3.56 .34 83° 1400 46.51
Series TC-207-R, 210-R
These clamps lock in both clampedand unclamped positions. Boltretainer supplied with solid barmodels. Flanged washers suppliedwith U-bar models. Series 207accommodates any 5/16” spindle.Series 210 accommodates any 3/8”spindle.
Discount 30 applies. C
B
Locking Mechanism
A
TC-207-LRTC-210-UR
BarType
Base Type
HoldingCapacity Lbs.
Bar Opening
Price Each1-49Cat. No. A B C D E F
TC-207-LR 6.90 1.25 4.58 .75 1.25 .28 Solid Flanged 500 100° 30.93TC-207-UR 6.90 1.25 4.58 .75 1.28 .25 U-Bar Flanged 375 100° 31.01TC-210-SR 8.00 1.68 6.61 1.25 1.75 .33 Solid Flanged 750 103° 44.07TC-210-UR 8.00 1.68 6.61 1.25 1.75 .33 U-Bar Flanged 600 103° 43.42
Designed with maximum safety and ergonomic benefits as itsfoundation, these toggle-lock plus clamps offer many outstandingfeatures, including:
• Bushings at major pivot points for longer life• Stop point locations at the base for added durability• Greater hand clearance for ease of use• Elimination of pinch points for added safety• Extended handle length for improved ergonomics• Longer clamping arm for greater flexibility• Spindle contacts workpiece in vertical position for less
workpiece marring or movement• Clamping arm completely clears workpiece for easy load/unload
Toggle-Lock Plus clamps have a locking release lever for improved safety. Used in applications where there is severe stress or vibrationon the clamps, or for over-head installations.
Toggle-Lock Plus
Discount 30 applies.
Cat. No. A B C D D1 E F G H JHandleMoves
BarOpens
HoldingCapacity
Lbs.
PriceEach1-49
TC-2002-S 4.73 3.29 .95 .90 .50 1.06 1.36 1.52 1.93 .22 85 71 600 15.39TC-2002-U 4.73 3.29 .95 .90 .50 1.06 1.36 1.52 1.93 .22 85 71 600 14.68TC-2002-UB 5.07 3.29 1.27 .90 .50 .25 1.36 — 1.93 .22 85 71 600 16.32TC-2007-S 7.21 4.81 1.25 1.25 .75 1.25 1.93 1.94 2.88 .28 76 65 1000 19.49TC-2007-U 7.21 4.81 1.25 1.25 .75 1.25 1.93 1.94 2.88 .28 76 65 1000 18.89TC-2007-UB 7.64 4.81 1.68 1.25 .75 .25 1.93 — 2.88 .28 76 65 1000 20.31TC-2010-S 9.00 6.09 1.70 1.25 — 1.78 2.53 2.62 3.56 .34 83 69 1400 29.22TC-2010-U 9.00 6.09 1.70 1.25 — 1.78 2.53 2.62 3.56 .34 83 69 1400 28.21TC-2010-UB 9.612 6.09 2.20 1.25 — .316 2.53 — 3.56 .34 83 69 1400 30.11
0112.qxd 2/17/2010 2:57 PM Page 112
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 113
Clam
ps an
d W
orkh
old
ing
VERTICAL HANDLE HOLD-DOWN CLAMPS
See pages 136 and 137 for clamp accessories.
Series TC-201Holding Capacity: 100 Lbs.Handle Moves: 60°, Bar Moves: 110°
Steel models furnished with neoprene tipped M4 spindle(TC-201208-M), flanged washers and lock nuts. Stainlessmodels furnished with stainless steel hex head spindle(TC-201943), without neoprene tip.
Note: Also available as power Model TC-812. See page 139.
Discount 30 applies.
TC-201-UB
TC-201-TU
TC-201-U
Cat. No. A B C D EHandleType
BarType
BaseType
Price Each1-49
SteelTC-201-U 3.03 .63 2.02 .63 .94 Vertical U-Bar Flange 10.77TC-201-TU 2.25 .63 2.02 .63 .94 Tee U-bar Flange 14.17TC-201-UB 3.13 .88 2.02 .63 .16 Vertical U-Bar Straight 12.49Stainless SteelTC-201-USS 3.03 .63 2.02 .63 .94 Vertical U-Bar Flange 21.28
Series TC-202Holding Capacity: 200 Lbs.Handle Moves: 64°, Bar Moves: 104°
Steel furnished with M6 spindle (TC-202208-M) and lock nuts.U-bar models also include flanged washers.
Note: Also available as power Model TC-802. See page 139.
Discount 30 applies.
TC-202-UB
TC-202-T
TC-202
Cat. No. A B C D EHandleType
BarType
BaseType
Price Each1-49
SteelTC-202 4.21 .94 2.31 .50 1.06 Vertical Fixed Flange 11.30TC-202-T 2.81 .94 2.31 .50 1.06 Tee Fixed Flange 15.42TC-202-TU 2.81 .94 2.69 .50 1.06 Tee U-Bar Flange 15.42TC-202-B 4.40 1.13 2.31 .50 .25 Vertical Fixed Straight 13.57TC-202-U 4.21 .94 2.73 .50 1.06 Vertical U-Bar Flange 11.30TC-202-UL 4.21 .94 3.27 .50 1.06 Vertical U-Bar Flange 13.09TC-202-UB 4.40 1.13 2.73 .50 .25 Vertical U-Bar Straight 13.57Stainless SteelTC-202-SS 4.21 .94 2.31 .50 1.06 Vertical Fixed Flange 26.79TC-202-USS 4.21 .94 2.73 .50 1.06 Vertical U-Bar Flange 26.79TC-202-UBSS 4.40 1.13 2.73 .50 .25 Vertical U-Bar Straight 32.81
Series TC-207Holding Capacity: -L and -S Models = 500 Lbs.U Model = 375 Lbs.Handle Moves: 62°, Bar Moves: 115°
Bolt retainers are furnished with solid bar models. Two flangedwashers are furnished with U-bar models. Accommodates any5/16" spindle.
Note: Also available as power Model TC-807-L, see page 139, and asToggle-Lock Plus Model TC-207-LR and TC-207-UR, see page 112.
*Supplied with spindle TC-225208-M
Discount 30 applies.
A A
BB
E
C
D
TC-207-L
TC-207-TS
TC-207-UO
Cat. No. A B C D EHandleType
BarType
Base Type
Price Each1-49
SteelTC-207-L 6.89 1.25 5.02 .75 1.25 Vertical Solid Flange 16.76TC-207-LB 7.48 1.55 5.02 .75 .25 Vertical Solid Straight 17.63TC-207-S 6.89 1.25 3.75 .75 1.25 Vertical Solid Flange 14.75TC-207-SB 7.48 1.55 3.75 .75 .25 Vertical Solid Straight 17.03TC-207-TS 4.36 1.25 3.75 .75 1.25 Tee Solid Flange 19.35TC-207-U* 6.89 1.25 3.68 .75 1.25 Vertical U-Bar Flange 14.75TC-207-UB* 7.48 1.55 3.68 .75 .25 Vertical U-Bar Straight 17.03TC-207-TU 4.36 1.25 3.75 .75 1.25 Tee U-Bar Flange 19.02TC-207-UL* 6.89 1.25 5.41 .75 1.25 Vertical U-Bar Flange 15.01TC-207-ULB* 7.48 1.55 5.41 .75 .25 Vertical U-Bar Straight 17.36TC-207-TUL 4.36 1.25 5.41 .75 1.25 Tee U-Bar Flange 19.02Stainless SteelTC-207-USS 5.63 1.25 4.38 .75 1.25 Vertical U-Bar Flange 34.51
Series TC-210Holding Capacity: 750 Lbs. (max. for solid bar models)Holding Capacity: 600 Lbs. (max. for U-bar models)Handle Moves: 66°, Bar Moves: 122°
Two flanged washers (TC-235106) furnished with U-bar modelsand bolt retainer (TC-210114) supplied with solid bar models.Accommodates any 3/8” spindle.
Note: Also available as power Model TC-810-U, see page 139, and asToggle-Lock Plus Model TC-210-SR and TC-210-UR, see page 112.
*Supplied with spindle TC-240208-M
Discount 30 applies.
TC-210-SB
TC-210-U
Cat. No. A B C D EHandleType
BarType
BaseType
Price Each1-49
SteelTC-210-U* 8.00 1.67 5.53 1.25 1.78 Vertical U-Bar Flange 21.54TC-210-UB* 8.16 2.19 5.53 1.25 .31 Vertical U-Bar Straight 27.31TC-210-S 8.00 1.67 5.53 1.25 1.78 Vertical Solid Flange 24.06TC-210-SB 8.16 2.19 5.35 1.25 .31 Vertical Solid Straight 27.98TC-210-TU 5.38 1.69 5.35 1.25 1.78 Tee U-bar Flange 29.82Stainless SteelTC-210-USS 7.66 1.69 5.35 1.25 1.78 Vertical U-bar Flange 47.90
0113.qxd 2/17/2010 2:57 PM Page 113
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!114
Cla
mp
s an
d W
ork
ho
ldin
gVERTICAL HANDLE HOLD-DOWN CLAMPS
See pages 136 and 137 for clamp accessories.
TC-229Handle Moves: 180°, Bar Moves: 115°
Featuring a unique cam action, these clamps will hold workpiecesof inconsistent height. Ideal for castings or forgings. Once set fornominal or average piece height, it will allow for a 5/32” deviationlarger or smaller than average. Overall clamping range is 5/16”.Furnished with 1/2” spindle assembly (TC-220203).
Discount 30 applies.
Series TC-247Holding Capacity: 1,000 Lbs.Handle Moves: 75°, Bar Moves: 136°
Bolt retainer furnished with solid bar models. Flanged washersfurnished with U-bar models. Accommodates any 1/2” spindle.
Note: Also available as power Model TC-847. See page 139.
Discount 30 applies.
TC-247-U
TC-247-S
Cat. No. A B C D EHandleType
BarType
BaseType
PriceEach1-49
TC-247-U 8.69 2 6.87 1.25 1.78 Vertical U-Bar Flange 31.56TC-247-S 8.69 2 6.87 1.25 1.78 Vertical Solid Flange 36.61
Series TC-267Holding Capacity: 1,200 Lbs.Handle Moves: 70°, Bar Moves: 140°
Bolt retainer furnished with solid bar models. Flanged washersfurnished with U-Bar models. Accommodates any 5/8” spindle.
Discount 30 applies.
TC-267-S
TC-267-U
Cat. No. A B C D EHandleType
Bar Type
Base Type
Price Each1-49
TC-267-S 11.88 3.08 8.88 2 2.75 Vertical Solid Flange 50.94TC-267-U 11.88 3.08 8.92 2 2.75 Vertical U-Bar Flange 49.97
TC-91090Holding Capacity: 385 LbsHandle Moves: 60°, Bar Moves: 100°
TC-91140 Holding Capacity: 1,000 Lbs.Handle Moves: 65°, Bar Moves: 100°
Front flange mount for mounting flexibility on vertical surfaces.Stainless steel rivets for increased strength. Guide bars allowfor more clamp stability. Supplied with two flanged washers.TC-91090 accommodates any 5/16” or M8 spindle. TC-91140accommodates any 3/8” or M10 spindle. Spindles not included.
Discount 30 applies.
TC-91090
Cat. No. A B C D E F G H J K LPrice Each
1-49TC-91090 7.68 4.72 2.68 .80 1.29 1.32 2.09 2.99 .28 2.40 .33 18.14TC-91140 11.06 7.87 5.24 1.26 1.81 2.17 2.74 5.24 .33 4.41 .43 27.25
HoldingCapacity
(Lbs.)
PriceEach1-49Cat. No. A B C D E F G H I J K
TC-229 9.94 7.13 2.06 .88 2.0 1.88 2.75 5.25 1/2-13 .33 2.75 1,000 61.79
0114.qxd 2/17/2010 2:57 PM Page 114
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 115
Clam
ps an
d W
orkh
old
ing
VERTICAL HANDLE HOLD-DOWN CLAMPS
See pages 136 and 137 for clamp accessories.
Series TC-516Holding Capacity: 750 Lbs.Handle Moves: 66°, Bar Moves: 122°
Compact clamps with great holding capacity. Made from C-1008or C-1010 low carbon, cold rolled steel with a black oxide finish.Hardened and ground pivots can be replaced. Forged clamps canbe cut or welded to suit fixturing or tooling needs.
Discount 30 applies.
G
AA
C C
E
HH F
B
F
D J
516-B
516 516
516-B
TC-516 TC-516-B
Cat. No. A B C D E F G HBaseType
Price Each1-49
TC-516 6.31 4.00 1.25 — — 1.63 .53 2.38 Straight 81.92TC-516-B 6.72 4.38 1.50 1.00 1.50 2.00 2.00 2.19 Flange 92.63
TC-518Holding Capacity: 500 Lbs.Handle Moves: 75°, Bar Moves: 90°
Features a forged hold-down bar and ergonomic plastic grip.Forged hold-down bar can be cut or welded to suit the fixture.Offers twice the normal clearance under the bar as other clampsthis size.
Discount 30 applies.
Cat. No. A B C D E F G H JPrice Each
1-49TC-518 6.88 4.28 2.5 1.00 .88 1.50 1.38 2.63 .29 27.69
TC-548, 578Handle Moves: 129°, Bar Moves: 199°
Largest capacity clamps. The “bar-guide” feature provides extrasupport and improves rigidity and repeatability.
Discount 30 applies.
Cat. No. A B CHoldingCapacity
HandleType
BarType
BaseType
Price Each1-49
TC-548 9.44 2.25 7.50 2,500 Vertical Solid Straight 90.63TC-578 11.00 2.75 8.63 4,000 Vertical Solid Straight 140.87
Cam Action Clamps
Automatically compensates for variations in part thickness. A high to low limit clamping range allows for normal part size variation andeliminates adjustments. Normalized cast steel construction for heavy duty use. Fast, one hand operation. Cam action resists vibrationloosening. Accommodates from 1/8” to 1/2” part size variation.
M D
N
N
J
A
EH
C
FBG
LK
Maximum HoldingCapacity Lbs.
PriceEachCat. No. A B C D E F G H J K L M N
TC-7-101 5.00 3.13 1.44 .50 1.75 1.25 .75 1.25 .25 .25 .22 .50 .13 475 84.52TC-7-58 7.00 2.55 1.88 .56 2.25 1.69 1.00 1.62 .31 .34 .28 .50 .13 600 143.02TC-7-59 8.50 3.50 2.19 .63 2.50 2.06 1.38 1.88 .31 .39 .34 .63 .19 1,000 172.13TC-7-60 9.50 4.38 2.50 .88 2.88 2.44 1.62 2.12 .38 .44 .41 .75 .25 1,600 210.64TC-7-61 13.93 5.93 2.88 1.25 4.50 3.00 2.00 3.50 .51 .50 .53 1.13 .38 3,750 346.37
0115.qxd 2/22/2010 10:12 AM Page 115
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!116
Cla
mp
s an
d W
ork
ho
ldin
gECONOMY VERTICAL HANDLE HOLD-DOWN CLAMPS
All models have a blue vinyl grip handle. Supplied with spindle assembly.
A
A
C C
H B
L
E
A A
D
E
F
G
K
Ø J
ETC-11020
ETC-11021ETC-11022
ETC-11025ETC-11026
Cat. No. A B C D E F G H J K LBar
TypeBaseType
HandleType
HoldingCap. Lbs.
SpindleSize
HandleMoves
BarMoves
PriceEach
ETC-11011 3.38 2.07 0.73 0.63 0.95 1.00 1.32 1.06 0.17 0.77 — U-Bar Flanged Standard 100 #10-24 X 1.38 Bonded 56° 100° 7.36ETC-11012 3.65 2.04 1.00 0.63 0.14 1.00 — 1.03 0.17 0.82 — U-Bar Straight Standard 100 #10-24 X 1.38 Bonded 56° 100° 8.23ETC-11013 2.41 2.07 0.68 0.63 0.94 1.00 1.32 1.06 0.17 0.81 1.77 U-Bar Flanged T Handle 100 #10-24 X 1.38 Bonded 56° 100° 9.15ETC-11020 4.01 2.50 0.98 0.51 1.00 0.98 1.50 1.28 0.21 — — Solid Flanged Standard 200 1/4-20 X 1.75 Bonded 60° 100° 7.95ETC-11021 4.01 2.68 0.95 0.52 1.03 0.98 1.50 1.68 0.20 1.08 — U-Bar Flanged Standard 200 1/4-20 X 1.75 Bonded 60° 100° 7.95ETC-11022 4.27 2.68 1.18 0.51 0.26 0.98 — 1.68 0.21 1.08 — U-Bar Straight Standard 200 1/4-20 X 1.75 Bonded 60° 100° 9.06ETC-11023 3.12 2.68 0.98 0.51 1.03 0.98 1.53 1.70 0.21 0.98 2.60 U-Bar Flanged T Handle 200 1/4-20 X 1.75 Bonded 60° 100° 9.90ETC-11025 4.23 2.48 1.15 0.72 0.24 0.98 — 1.24 0.21 — — Solid Straight Standard 200 1/4-20 X 1.75 Bonded 60° 100° 9.06ETC-11026 3.03 2.50 0.97 0.56 0.99 0.98 1.48 1.26 0.21 — 2.60 Solid Flanged T Handle 200 1/4-20 X 1.75 Bonded 60° 100° 9.90
All models have a blue vinyl grip handle. Supplied with spindle assembly.
A
A
C C
H B
L
E
A A
D
E
F
G
K
Ø J
ETC-11071
ETC-11072ETC-11073
ETC-11074
Cat. No. A B C D E F G H J K LBar
TypeBaseType
HandleType
HoldingCap. Lbs.
SpindleSize
HandleMoves
BarMoves
PriceEach
ETC-11018 5.60 5.43 1.25 0.78 1.25 1.38 1.77 3.75 0.27 2.79 — Long U-Bar Flanged Standard 500 5/16-18 X 2.50 Bonded 60° 100° 10.61ETC-11019 5.90 5.50 1.62 0.75 0.25 1.38 — 2.85 0.27 2.85 — Long U-Bar Straight Standard 375 5/16-18 X 2.50 Bonded 60° 100° 11.41ETC-11071 5.88 4.59 1.23 0.75 1.25 1.38 1.82 2.85 0.27 2.05 — U-Bar Flanged Standard 200 5/16-18 X 2.50 Bonded 60° 100° 10.42ETC-11072 5.93 4.61 1.57 0.75 0.25 1.38 — 2.85 0.27 2.03 — U-Bar Straight Standard 375 5/16-18 X 2.50 Bonded 60° 100° 11.41ETC-11073 4.10 4.60 1.23 0.75 1.25 1.38 1.77 2.86 0.27 2.10 3.86 U-Bar Flanged T Handle 375 5/16-18 X 2.50 Bonded 60° 100° 12.29ETC-11074 5.90 3.75 1.26 0.75 1.25 1.38 1.80 2.24 0.27 — — Solid Bar Flanged Standard 375 5/16-18 X 2.50 Bonded 60° 100° 10.42ETC-11077 6.12 3.75 1.57 0.75 0.25 1.38 — 2.24 0.27 — — Solid Straight Standard 375 5/16-18 X 2.50 Bonded 60° 100° 11.41ETC-11078 5.58 4.78 1.26 0.75 1.25 1.38 1.76 3.40 0.27 — — Long Solid Flanged Standard 500 5/16-18 X 2.50 Bonded 60° 100° 11.77ETC-11079 6.12 4.85 1.57 0.75 0.25 1.38 — 3.47 0.27 — — Long Solid Straight Standard 500 5/16-18 X 2.50 Bonded 60° 100° 11.77
Verticle Handle Hold-Down Clamps
All models have a blue vinyl grip handle. Supplied with spindle assembly.
A
A
C C
H B
L
E
A A
D
E
F
G
K
Ø J
Cat. No. A B C D E F G H J K LBar
TypeBaseType
HandleType
HoldingCap. Lbs.
SpindleSize
HandleMoves
BarMoves
PriceEach
ETC-11101 7.96 5.65 1.66 1.25 1.80 1.94 2.55 3.56 0.31 2.31 — U-Bar Flanged Standard 600 3/8-16 X 3.50 Bonded 58° 105° 15.19ETC-11102 8.46 5.65 2.18 1.25 0.31 1.94 -— 3.56 0.31 2.23 — U-Bar Straight Standard 600 3/8-16 X 3.50 Bonded 58° 105° 17.01ETC-11103 5.60 5.50 1.62 1.25 1.77 1.94 2.50 3.56 0.31 2.40 5.13 U-Bar Flanged T Handle 600 3/8-16 X 3.50 Bonded 58° 105° 18.24ETC-11104 7.89 5.59 1.26 1.25 1.81 1.94 2.56 3.53 0.31 — — Solid Flanged Standard 750 3/8-16 X 3.50 Bonded 58° 105° 16.10ETC-11107 8.46 5.59 2.16 1.25 0.35 1.94 — 3.59 0.31 — — Solid Straight Standard 750 3/8-16 X 3.50 Bonded 58° 105° 17.45
Verticle Handle Hold-Down Clamps
Verticle Handle Hold-Down Clamps
0116.qxd 2/22/2010 10:17 AM Page 116
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 117
Clam
ps an
d W
orkh
old
ing
ECONOMY VERTICAL HANDLE HOLD-DOWN CLAMPS
Vertical Handle Hold-Down Action Clamps
All models have a blue vinyl grip handle. Supplied with spindle assembly.
E
B
K
FD ØJ
E G
C
A
H
Cat. No. A B C D E F G H J KBar
TypeBaseType
HandleType
HoldingCap. Lbs.
SpindleSize
HandleMoves
BarMoves
PriceEach
ETC-11471 8.81 6.89 1.95 1.25 1.77 2.00 2.56 4.87 0.35 2.98 U-Bar Flanged Standard 1000 1/2-13 X 3.00 Plain 70° 135° 22.26ETC-11472 9.17 6.89 2.31 1.25 0.31 2.00 — 4.90 0.35 3.00 U-Bar Straight Standard 1000 1/2-13 X 3.00 Plain 70° 135° 29.26ETC-11474 8.81 7.12 2.00 1.25 1.79 2.00 2.56 4.95 0.35 — Solid Flanged Standard 1000 1/2-13 X 3.00 Plain 70° 135° 24.13ETC-11477 9.17 7.12 2.72 1.25 0.39 2.00 — 4.95 0.35 — Solid Straight Standard 1000 1/2-13 X 3.00 Plain 70° 135° 32.00
Vertical Handle Hold-Down Action Clamps
All models have a blue vinyl grip handle. Supplied with spindle assembly.
DD
F
E G
K
H
C
BE
A
ØJ
Cat. No. A B C D E F G H J KBar
TypeBaseType
HandleType
HoldingCap. Lbs.
SpindleSize
HandleMoves
BarMoves
PriceEach
ETC-11671 11.87 9.00 3.08 2.00 2.75 2.99 3.75 5.99 0.48 4.33 U-Bar Flanged Standard 1200 1/2-13 X 4.50 Plain 60° 140° 33.47ETC-11674 11.83 8.97 3.22 2.00 2.75 2.99 3.75 5.99 0.48 — Solid Flanged Standard 1200 1/2-13 X 4.50 Plain 60° 140° 33.47
Vertical Handle Hold-Down Action Clamps
All models have a blue vinyl grip handle. Supplied with spindle assembly.
C
A
H
K
F
D
E G
C
B
ØJ
Cat. No. A B C D E F G H J KBar
TypeBaseType
HandleType
HoldingCap. Lbs.
SpindleSize
HandleMoves
BarMoves
PriceEach
ETC-11351 6.85 4.22 1.20 1.26 1.44 1.97 2.20 2.25 0.33 1.53 LowU-Bar Flanged Standard 850 3/8-16 X 3.50 Bonded 85° 90° 13.56ETC-11352 6.85 4.22 2.26 1.26 1.44 1.97 2.20 2.25 0.33 1.53 High U-Bar Flanged Standard 850 3/8-16 X 3.50 Bonded 85° 90° 13.56
0117.qxd 2/17/2010 2:59 PM Page 117
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!118
Cla
mp
s an
d W
ork
ho
ldin
gHORIZONTAL HANDLE HOLD-DOWN CLAMPS
TC-2013-U, 2017-U, 2027-U, 2037-UFlanged Base
A
ML
CH
L1
Cat No.Holding
Cap. Lbs.Bar
Opening A C H L L1 M Price EachTC-2013-U 295 71° .53 .75 1.27 5.88 1.65 10-32 13.37TC-2017-U 560 73° 1.03 .98 1.95 8.62 2.53 1/4-20 17.25TC-2027-U 840 68° 1.03 1.32 2.20 9.88 2.86 5/16-18 19.11TC-2037-U 1680 73° 1.63 1.62 2.75 13.35 4.40 3/8-16 32.22
MOpening
H
AL1
L
B
C
Cat No.Holding
Cap. Lbs.Bar
Opening A B C H L L1 M Price EachTC-2013-UR 295 70° .53 .70 .75 1.27 5.88 1.65 10-32 21.40TC-2017-UR 560 73° 1.03 1.21 .98 1.95 8.62 2.53 1/4-20 27.62TC-2027-UR 840 70° 1.03 1.21 1.32 2.20 9.88 2.86 5/16-18 30.52TC-2037-UR 1680 70° 1.63 1.69 1.62 2.75 13.35 4.40 3/8-16 52.95
Series TC-2005
Cat No.Holding
Cap. Lbs. A4 B C H L L1 M Price EachTC-2005-U 180 .09 .62 .31 .73 3.14 .85 M4 10.39TC-2005-S 100 .09 .62 .38 .73 3.12 .83 M4 10.39
• Robust design offers increased holding capacity over TC-213-U,217-U, 227-U, 237-U
• Low arm deflection under load (greater stiffness)• Mounting hole interchangeable with TC-213-U, 217-U, 227-U,
237-U• Large handle clearance reduces pinch points• Fixed handle pivot provides smooth action
• Robust design offers increased holding capacity over TC-205-Uand TC-205-S
• Mounting hole interchangeable with TC-205-U and TC-205-S• Large handle clearance reduces pinch points• Fixed handle pivot provides smooth action• Requires only two mounting screws
H
62°Opening
M
C
L1
B
A4L
TC-2013-UR, 2017-UR, 2027-UR, 2037-URFlanged BaseToggle Lock Plus®
• Additional locking lever lockshandle in closed and openpositions
• Robust design offers increasedholding capacity over TC-213-U,217-U, 227-U, 237-U
• Low arm deflection under load(greater stiffness)
• Mounting hole interchangeablewith TC-213-U, 217-U, 227-U,237-U
• Large handle clearance reducespinch points
• Fixed handle pivot providessmooth action
Series TC-205Holding Capacity: 60 Lbs.Handle Moves: 80°, Bar Moves: 90°
The smallest of the horizontalhandle, horizontal bar clamps.Steel models supplied with M4neoprene tipped spindleassembly (TC-205208-M).Stainless steel modelssupplied with stainless steelhex head spindle (TC-205943).
Discount 30 applies.
TC-205-S
TC-205-UR
TC-205-SB
TC-205-SL
TC-205-SR
TC-205-UB
Cat. No. A B C D EBar
TypeBase Type
Price Each1-49
SteelTC-205-S .67 .37 2.78 .53 .63 Solid Flange 8.33TC-205-SB .84 .63 2.78 .53 — Solid Straight 10.09TC-205-SL .67 .37 2.78 .53 — Solid Left Flange 10.72TC-205-SR .67 .37 2.78 .53 — Solid Right Flange 10.72TC-205-U .67 .31 2.65 .53 .63 U-Bar Flange 8.33TC-205-UB .84 .53 2.65 .53 — U-Bar Straight 10.30TC-205-UL .67 .31 2.65 .53 — U-Bar Left Flange 10.72TC-205-UR .67 .31 2.65 .53 — U-Bar Right Flange 10.72Stainless SteelTC-205-SSS* .67 .37 2.75 .53 .63 Solid Flange 16.15TC-205-USS* .67 .31 2.66 .53 .63 U-Bar Flange 15.82*Handle does not have vinyl grip.
TC-205-U
0118.qxd 3/5/2010 2:59 PM Page 118
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 119
Clam
ps an
d W
orkh
old
ingHORIZONTAL HANDLE HOLD-DOWN CLAMPS
See pages 136 and 137 for clamp accessories.
Series TC-206-SSHolding Capacity: 100 Lbs.Handle Moves: 90°, Bar Moves: 90°
Made of stainless steel. Offers good clearance height under thebar, while maintaining a low profile. Optional high bar provideseven more space to clamp for thicker material. Furnished withflanged washers (TC-105906) and stainless steel spindle assem-bly (TC-205943), two 8-32 lock nuts and one 8-32 x 3/4” bolt.
Discount 30 applies.
TC-206-SS
TC-206-HSS
Series TC-215Holding Capacity: 200 Lbs.Handle Moves: 70°, Bar Moves: 90°
All steel models furnished with M6 bonded neoprene spindle(TC-202208-M), lock nuts and flanged washers or bolt retainer.Stainless steel models supplied with stainless steel hex headspindle (TC-202943), without neoprene tip.
Discount 30 applies.
TC-215-U
Series TC-225Holding Capacity: 500 Lbs.Handle Moves: 70°, Bar Moves: 90°
Steel models furnished with M8 bonded neoprene tippedspindle (TC-225208-M), flanged washers and lock nuts.Stainless steel models supplied with stainless steel hex headspindle (TC-207943), without neoprene tip.Discount 30 applies.
TC-225-U
TC-225-UB
BarType
BaseType
Price Each1-49Cat. No. A B C D E
SteelTC-225-U 1.84 1.32 6.70 1 .88 U-Bar Flange 12.82TC-225-UB 2.13 1.63 6.70 1 — U-Bar Straight 16.41Stainless SteelTC-225-USS* 1.84 1.32 6.70 1 .88 U-Bar Flange 30.98*Handle does not have plastic grip
TC-225-URToggle-Lock PlusHolding Capacity: 500 Lbs.Handle Moves: 70°, Bar Moves: 90°
TC-235-URToggle-Lock PlusHolding Capacity: 750 Lbs.Handle Moves: 55°, Bar Moves: 90°
Equipped with a release lever which locks in clamped position only. Large handle pad for greater comfort. TC-225-UR supplied with anM8 neoprene tipped spindle assembly (TC-225208-M) and two washers (TC-507107). TC-235-UR furnished with M10 bondedneoprene tipped spindle (TC-240208-M), flanged washers and lock nuts.Discount 30 applies.
LOCKINGMECHANISM
C
BA
D
EF
TC-225-UR TC-235-UR
Series TC-235Holding Capacity: 750 Lbs.Handle Moves: 55°, Bar Moves: 90°
Steel models furnished with M10 bonded neoprene tippedspindle (TC-240208-M), flanged washers and lock nuts.Stainless steel models supplied with stainless steel hex headspindle (TC-237943), without neoprene tip.
Discount 30 applies.
TC-235-U
TC-235-UB
BarType
BaseType
Price Each1-49Cat. No. A B C D E
SteelTC-235-U 2.55 1.75 10.87 1.63 1.63 U-Bar Flanged 21.69TC-235-UB 2.91 2.16 10.87 1.63 .31 U-Bar Straight 24.99Stainless SteelTC-235-USS 2.55 1.75 10.87 1.63 1.63 U-Bar Flanged 52.98
Cat. No. A B C D EBar
TypeBaseType
Price Each1-49
SteelTC-215-S 1.53 1.03 5.50 1 .88 Solid Flange 14.18TC-215-U 1.53 1.03 5.50 1 .88 U-Bar Flange 11.23TC-215-UB 1.78 1.28 5.50 1 .19 U-Bar Straight 13.41Stainless SteelTC-215-USS* 1.53 1.03 5.50 1 .88 U-Bar Flange 22.38*Handle does not have plastic grip
Cat. No. A B C D EBar
TypeBaseType
Price Each1-49
Stainless SteelTC-206-SS 1.06 .40 2.75 .53 .63 Low U-Bar Flanged 23.65TC-206-HSS 1.06 .75 2.75 .53 .63 High U-Bar Flanged 23.65
Bar Type
BaseType
Price Each1-49Cat. No. A B C D E F
TC-225-UR 1.92 1.32 7.14 1.00 .88 .27 U-Bar Flanged 29.31TC-235-UR 2.50 1.75 10.50 1.63 1.63 .33 U-Bar Flanged 48.13
0119.qxd 2/23/2010 12:43 PM Page 119
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!120
Cla
mp
s an
d W
ork
ho
ldin
gHORIZONTAL HANDLE HOLD-DOWN CLAMPS
See pages 136 and 137 for clamp accessories.
Series TC-305, 307, 309
Small compact clamps provide considerable holding capacityin a small size. T-handle can be operated from either side orfrom behind. All have U-Bar and flanged base. TC-305-USSand TC-307-USS handle moves 175°, bar 92°. TC-309-USShandles moves 160°, bar moves 88°. Supplied with fullythreaded, stainless steel, hex head spindle, without neoprenetip, except TC-309-USS, which comes with press on neoprenecap. See page 136 for accessories.
Discount 30 applies.
TC-305-USS
HoldingCapacity
Price Each1-49Cat. No. A B C D E F
SteelTC-305-U 1.38 .50 2.22 .53 .63 M5 150 10.50TC-307-U 2.40 .87 3.60 0.91 1.16 M8 350 15.77TC-309-U 3.55 1.30 5.18 1.38 1.5 M10 750 26.14Stainless SteelTC-305-USS 1.38 .50 2.22 .53 .63 10-32 150 20.84TC-307-USS 2.40 .87 3.60 .91 1.16 5/16-18 350 33.72TC-309-USS 3.55 1.30 5.18 1.38 1.50 3/8-16 750 50.29
These clamps feature a compact locking release lever, which locks in the clamped position only. Provided with red vinyl handle grip andflanged washers. TC-305-UR and TC-307-UR are supplied with neoprene-tipped spindle assemblies. TC-309-UR is provided with a hex-head spindle assembly and slip-on neoprene cap TC-235119.
Discount 30 applies.
TC-309-UR
Cat. No.HoldingCapacity
HandleMoves°
BarOpening°
FlangedWasher
SpindleAssembly A B C D E F G H J K
Price Each1-49
TC-305-UR 150 Lbs. 175 92 TC-102111 TC-305208-M 1.44 2.25 .50 .53 .63 1.03 1.00 1.22 .17 .50 21.47TC-307-UR 350 Lbs. 175 92 TC-507107 TC-307208-M 2.44 3.61 .88 .91 1.16 1.72 1.81 1.89 28 .75 29.21TC-309-UR 750 Lbs. 160 92 TC-235106 TC-309208 3.59 5.19 1.31 1.38 1.50 2.52 2.47 2.66 33 1.06 43.15
Series TC-213, 217, 227, 237, 245
Safety designed to give more hand clearance between the barand handle when clamps are in full, open position. Bar guidefeature gives extra lateral support and rigidity to hold-down bar atfront of base. Steel series 213, 217, 227, 237 are supplied withneoprene tipped spindle assemblies and flanged washers. Series245 and all stainless steel clamps are supplied with a hex headspindle assembly. U-bar type.
Discount 30 applies.
TC-213-U
Cat. No. A B C D E FHandleMoves°
BarMoves°
BaseType
HoldingCapacity
PriceEach1-49
SteelTC-213-U 1.39 .72 4.12 .53 .70 M5 60 90 Flange 150 10.82TC-217-U 1.95 .97 6.56 1.03 1.12 M6 76 92 Flange 200 14.00TC-227-U 2.43 1.30 7.56 1.03 1.22 M8 62 92 Flange 500 15.44TC-237-U 3.20 1.62 10.67 1.63 1.69 M10 63 92 Flange 750 26.01TC-245-U 4.25 2.25 12.33 1.63 1.63 1/2-13 67 105 Flange 1,000 41.26Stainless SteelTC-213-USS 1.36 .75 3.94 .53 .69 10-32 60 90 Flange 150 21.83TC-217-USS 1.97 .97 6.30 1.03 1.15 1/4-20 76 92 Flange 250 26.40TC-227-USS 2.39 1.31 7.24 1.03 1.23 5/16-18 62 92 Flange 600 34.95
Series TC-317Holding Capacity: 375 Lbs.Handle Moves: 60°, Bar Moves: 185°
U-Bar model furnished with M8 bonded neoprene tipped spindle,flanged washers and lock nuts.
Discount 30 applies.
AB
C
E
D 329 Dia.
TC-317-S
Cat. No. A B C D EBar
TypePrice Each
1-49TC-317-S 5.62 2.67 6.44 0.63 1 Solid 21.67TC-317-U 5.62 2.67 6.07 0.63 1 U-Bar 22.76
Series TC-527, 528Holding Capacity: 1,000 Lbs.Handle Moves: 65°, Bar Moves: 195°
For tough, heavy-duty workholding. Clamp has square, colddrawn steel hold down bar. Pivot points have serrated, hardenedbushings.
Discount 30 applies.
TC-527-F
TC-527
Cat. No.BaseType
HandleType
Price Each1-49
TC-527 Flanged Pull Down 65.13TC-527-F Front Mount / Straight Pull Down 65.13TC-528 Flanged Vertical 65.13TC-528-F Front Mount / Straight Vertical 65.13
TC-305-UR, 307-UR, 309-URToggle-Lock Plus
TC-317-U
0120.qxd 2/17/2010 3:01 PM Page 120
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 121
Clam
ps an
d W
orkh
old
ing
ECONOMY HORIZONTAL HOLD-DOWN CLAMPSHorizontal HandleHold-Down Clamps
All models have a blue handle grip. Supplied with spindle assembly.
E
A A
H
C CCC
B
K
ØJ
DF
E G
Cat. No. A B C D E F G H J KBar
TypeBaseType
HandleType
HoldingCap. Lbs.
SpindleSize
HandleMoves
BarMoves
PriceEach
ETC-16351 3.15 9.00 1.20 1.27 1.47 1.97 2.20 2.25 0.33 1.53 Low U-Bar Flanged Standard 850 3/8-16 X 3.50 Bonded 90° 90° 13.55ETC-16352 3.15 9.00 2.26 1.27 1.47 1.97 2.20 2.25 0.33 1.53 High U-Bar Flanged Standard 850 3/8-16 X 3.50 Bonded 90° 90° 13.56ETC-16353 4.00 9.00 2.03 1.27 — 1.97 — 2.25 0.33 1.53 Low U-Bar Straight Standard 850 3/8-16 X 3.50 Bonded 90° 90° 13.78ETC-16354 4.00 9.00 3.15 1.27 — 1.97 — 2.25 0.33 1.53 High U-Bar Straight Standard 850 3/8-16 X 3.50 Bonded 90° 90° 13.78
Horizontal HandleHold-Down Clamps
All models have a blue handle grip. Supplied with spindle assembly.
A
C
H B
F D ØJ
E G L
K
Cat. No. A B C D E F G H J K LBar
TypeBaseType
HandleType
HoldingCap. Lbs.
SpindleSize
HandleMoves
BarMoves
PriceEach
ETC-16051 1.47 2.30 0.65 0.53 0.66 1.03 1.03 1.26 0.17 0.44 1.32 U-Bar Flanged T-Handle 150 #10-24 X 1.38 Bonded 170° 90° 7.40ETC-16071 2.49 3.68 0.89 0.91 1.17 1.72 1.82 1.93 0.28 0.77 2.01 U-Bar Flanged T-Handle 350 5/16-18 X 2.50 Bonded 170° 90° 10.90ETC-16091 3.73 5.33 1.31 1.38 1.50 2.52 2.52 2.81 0.31 1.32 2.48 U-Bar Flanged T-Handle 750 3/8-16 X 3.50 Bonded 170° 90° 16.27
Horizontal HandleHold-Down Clamps
All models have a blue handle grip. Supplied with spindle assembly.
C C
H B E
A A
K
D
F
Ø J
E G
ETC-14051
ETC-14052
ETC-14054
ETC-14057
ETC-14151
ETC-14152
Cat. No. A B C D E F G H J KBar
TypeBaseType
HandleType
HoldingCap. Lbs.
SpindleSize
HandleMoves
BarMoves
PriceEach
ETC-14051 0.70 3.10 0.34 0.42 0.65 0.95 0.98 0.78 0.17 0.48 U-Bar Flanged Standard 60 #8-32 X .75 Nylon 80° 90° 5.84ETC-14052 0.83 3.11 0.47 0.40 0.11 0.95 — 0.78 0.17 0.48 U-Bar Straight Standard 60 #8-32 X .75 Nylon 80° 90° 6.52ETC-14054 0.73 3.24 0.42 0.41 0.64 0.95 0.98 0.87 0.17 — Solid Flanged Standard 60 #8-32 X .75 Nylon 80° 90° 5.84ETC-14057 0.87 3.23 0.54 0.40 0.11 0.95 — 0.87 0.17 — Solid Straight Standard 60 #8-32 X .75 Nylon 80° 90° 6.52ETC-14151 1.52 5.90 0.96 0.98 0.87 1.46 1.36 2.29 0.21 1.51 U-Bar Flanged Standard 200 1/4-20 X 2.13 Bonded 60° 85° 8.11ETC-14152 1.76 5.90 1.23 0.98 0.16 1.46 — 2.28 0.21 1.33 U-Bar Straight Standard 200 1/4-20 X 2.13 Bonded 60° 85° 8.95ETC-14154 1.52 5.90 1.00 0.98 0.83 1.46 1.36 2.29 0.21 — Solid Flanged Standard 200 1/4-20 X 2.13 Bonded 60° 85° 8.83ETC-14157 1.76 5.90 1.26 0.98 0.16 1.46 — 2.29 0.21 — Solid Straight Standard 200 1/4-20 X 2.13 Bonded 60° 85° 11.29ETC-14251 1.96 6.88 1.31 0.99 0.89 1.51 1.36 2.91 0.28 1.31 U-Bar Flanged Standard 500 5/16-18 X 3.00 Bonded 65° 90° 9.34ETC-14252 2.18 6.88 1.66 0.99 0.23 1.51 — 2.91 0.28 1.42 U-Bar Straight Standard 500 5/16-18 X 3.00 Bonded 65° 90° 10.22ETC-14351 2.55 10.40 1.73 1.62 1.60 2.25 2.23 4.29 0.31 2.75 U-Bar Flanged Standard 750 3/8-16 X 3.50 Bonded 50° 85° 15.47ETC-14352 2.93 10.40 2.17 1.62 0.27 2.25 — 4.24 0.31 2.75 U-Bar Straight Standard 750 3/8-16 X 3.50 Bonded 50° 85° 17.06
ETC-14154
0121.qxd 2/17/2010 3:01 PM Page 121
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!122
Cla
mp
s an
d W
ork
ho
ldin
gPULL-ACTION LATCH CLAMPS
See pages 136 and 137 for clamp accessories.
Series TC-301, 311
Fixed stop automatically limits handle travel at variousclamping positions once the clamp is installed. Redvinyl handle for comfortable operation.
Discount 30 applies.
TC-301
DrawingMovement
HoldingCapacity (Lbs.)
Price Each1-49Cat. No. A B D E F G J K N
SteelTC-301 1.91 8.40 .75 1.25 1.38 1.75 .28 .56 .12 4.00 375 19.65TC-311 2.44 9.52 1.25 1.78 1.91 2.53 .33 .56 .13 3.38 1,200 26.50Stainless SteelTC-301-SS 1.91 8.40 .75 1.25 1.38 1.75 .28 .56 .12 4.00 375 45.37
Series TC-323, 331, 341
The threaded U-bolt permits easy adjustment and provides a positive connection with the supplied latch plate. Furnished with athumb control lever.
Discount 30 applies.
TC-323
Drawing Movement
Holding Capacity
(Lbs.)
PriceEach1-49Cat. No. A B C D E F G H J J1 K L N O
SteelTC-323 1.13 4.00 .39 .63 .75 1.02 1.11 .79 1.81 .17 .17 .75 .52 .13 .47 360 11.95TC-331 1.96 5.97 .56 .75 1.25 1.56 1.75 1.00 1.75 .27 .27 1.00 .69 .17 .66 700 15.91TC-341 2.89 7.50 .75 1.63 1.50 2.38 2.13 1.50 2.5 .33 .33 1.75 1.19 .31 .94 2,000 24.77Stainless SteelTC-323-SS 1.13 4.00 .39 .63 .75 1.02 1.11 .79 1.81 .17 .17 .75 .52 .13 .47 360 26.12TC-331-SS 1.96 5.97 .56 .75 1.25 1.56 1.75 1.00 1.75 .27 .27 1.00 .69 .17 .66 700 31.31TC-341-SS 2.89 7.50 .75 1.63 1.50 2.38 2.13 1.50 2.50 .33 .33 1.75 1.19 .31 .94 2,000 56.50
Series TC-323-R, TC-331-R, 341-RToggle-Lock Plus
Supplied with release lever catch which allows clamp to lock in closed position only. The threaded U-bolt provides easy adjustment anda positive connection with the supplied latch plate.
Discount 30 applies.
TC-331-R
DrawingMovement
HoldingCapacity Lbs.
Price Each1-49Cat. No. A B C D E F G H J O
SteelTC-323-R 1.23 4.00 .39 .63 .75 1.02 1.11 .79 1.17 .47 1.17 360 19.50TC-331-R 2.08 5.97 .56 .75 1.25 1.56 1.75 1.00 .27 .68 1.75 700 28.80TC-341-R 2.89 7.50 .75 1.63 1.50 2.38 2.12 1.50 .33 .94 2.50 2,000 42.18Stainless Steel
TC-323-RSS 1.23 4.00 .39 .63 .75 1.02 1.11 .79 1.17 .47 1.17 360 36.25TC-331-RSS 2.08 5.97 .56 .75 1.25 1.56 1.75 1.00 .27 .68 1.75 700 50.29TC-341-RSS 2.89 7.50 .75 1.63 1.50 2.38 2.12 1.50 .33 .94 2.50 2,000 83.44
0122.qxd 2/17/2010 3:02 PM Page 122
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 123
Clam
ps an
d W
orkh
old
ing
TC-375, 375-BHolding Capacity: 4,000 Lbs.Drawing Movement: 3-1/2
TC-385, 385-LHolding Capacity: 7,500 Lbs.Drawing Movement: 2-3/16
PULL-ACTION LATCH CLAMPS
See pages 136 and 137 for clamp accessories.
Latch plate is notincluded, soldseparately below(except for TC-375-B).Furnished with athumb control lever.
Discount 30 applies.
TC-375TC-375-B
w/ Latch Plate(TC-375509)
TC-385 TC-385-L TC-385102
Price Each1-49Cat. No. A B C D E F G H K L N O
TC-375 4.19 9.63 1.38 2.25 2.25 3.44 3.19 2.25 1.75 3.13 .39 1.13 55.75TC-375-B* 4.19 9.63 — — — 2.81 1.00 1.38 1.75 .88 .39 1.13 49.05TC-375509 Steel Latch Plate For TC-375-B 6.24TC-385 3.63 8.75 1.38 2.25 2.25 3.44 3.19 2.25 2.13 3.13 .47 1.13 72.73TC-385-L 1.94 9.16 1.38 2.25 2.25 3.44 3.19 2.25 2.13 3.13 .47 1.13 87.71TC-385102 Steel Latch Plate For TC-375 and TC-385 16.93*Narrow base
Series TC-375-R, TC-385-RToggle-Lock Plus
Heavy duty models.Supplied with a releaselever which locks into theforged steel base in closedposition only. Latch platenot included.TC-375-R
TC-385-R
TC-385102
DrawingMovement
HoldingCapacity Lbs.
Price Each1-49Cat. No. A B C D E F G H J K L N O
TC-375-R 4.19 9.63 1.28 2.25 2.25 3.44 3.13 2.25 .41 1.75 3.13 .39 1.13 3.50 4,000 73.65TC-385-R 3.63 8.75 1.38 2.25 2.25 3.44 3.19 2.25 .41 2.13 3.13 .47 1.13 2.19 7,500 93.50TC-385102 Steel Latch Plate For TC-375 and TC-385 16.93
Series TC-330, 351, 371, 381
Pull bar is threaded for convenient adjustment. Furnished with a thumb control lever.Discount 30 applies.
B
Q
C A
FD
J
EN
G K
TC-351
Holding Capacity
(Lbs.)Price Each
1-49Cat. No. A B C D E FDrawing
Movement G J K N Q Min. Q Max.SteelTC-330 .90 5.64 .56 .50 1.23 1.00 2.31 1.69 .22 .31 .19 1.60 1.85 200 14.17TC-351 1.34 8.56 .75 .75 1.38 1.50 4.00 1.94 .20 .38 .31 1.75 2.18 375 12.15TC-351-B* 1.34 8.56 — 1.50 — 2.00 4.00 .56 .27 .44 .31 1.75 2.18 375 13.68TC-371 2.23 12.00 1.42 1.25 1.94 1.94 5.38 2.62 .34 .50 .39 2.02 2.83 750 29.15TC-381 2.71 13.45 1.81 1.13 2.38 2.13 6.13 3.38 .41 .63 .47 2.17 3.10 1,000 33.80Stainless SteelTC-330-SS .90 5.64 .56 .50 1.23 1.00 2.31 1.69 .22 .31 .19 1.60 1.85 200 25.96TC-351-SS 1.34 8.56 .75 .75 1.38 1.50 4.00 1.94 .20 .44 .31 1.75 2.18 375 26.40TC-351-BSS* 1.34 8.56 — 1.50 — 2.00 4.00 .56 .27 .44 .31 1.75 2.18 375 26.90TC-371-SS 2.23 12.00 1.42 1.25 1.94 1.94 5.38 2.62 .34 .50 .39 2.02 2.83 750 67.19*Narrow base
Series TC-351, 371Toggle-Lock Plus
Supplied with a release lever catchwhich allows the clamp to lock inclosed position only. Large handlepad improves operability. Pull baris threaded for adjustment.
Discount 30 applies.
D O
G
AC
E
N
K
BH
F
D
J
TC-351-R
DrawingMovement
HoldingCapacity Lbs.
Price Each1-49Cat. No. A B C D E F G H J K N
TC-351-R 1.42 9.10 .75 .75 1.38 1.50 1.94 2.18 .22 .38 .31 4.00 375 26.50TC-371-R 2.25 12.88 1.42 1.25 1.94 1.94 2.62 2.83 .34 .50 .39 5.38 750 49.78
0123.qxd 2/17/2010 3:02 PM Page 123
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!124
Cla
mp
s an
d W
ork
ho
ldin
gPULL-ACTION LATCH CLAMPS
See pages 136 and 137 for clamp accessories.
Series TC-324, 334, 344, 374
Latch plate included with all clamps listed below except TC-374. Furnished with a thumb control lever.
Discount 30 applies.
TC-334
ThreadSize
HoldingCapacity
(Lbs)Price Each
1-49Cat. No. A B C D E F G HDrawing
Movement J J1 K L M N O P QSteelTC-324 2.00 3.35 .56 .50 .88 1.00 1.38 1.00 1.53 .20 .17 .81 .53 2.69 .14 .19 .63 .91 M4 500 17.95TC-334 2.44 4.25 .81 .75 1.00 1.31 1.56 1.50 2.00 .28 .22 1.13 .68 3.69 .25 .35 .69 1.35 M6 1,000 22.28TC-344 3.24 5.35 1.06 1.25 1.44 1.94 2.13 2.13 2.50 .34 .34 1.75 1.19 5.31 .31 .50 1.25 1.93 M8 2,000 33.74TC-374 2.67 5.69 .56 1.25 1.50 2.50 2.50 2.72 1.75 .41 .25 1.63 1.13 4.94 .39 .56 .75 2.34 M10 4,000 87.28Stainless SteelTC-324-SS 2.00 3.35 .56 .50 .88 1.00 1.38 1.00 1.53 .20 .17 .81 .53 2.69 .14 .19 .63 .91 M4 500 33.96TC-334-SS 2.44 4.25 .81 .75 1.00 1.31 1.56 1.50 2.00 .28 .22 1.13 .68 3.69 .25 .35 .69 1.35 M6 1,000 40.02TC-344-SS 3.25 5.35 1.06 1.25 1.44 1.94 2.13 2.13 2.50 .34 .34 1.75 1.19 5.31 .31 .50 1.25 1.93 M8 2,000 67.69
0124.qxd 2/22/2010 8:49 AM Page 124
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 125
Clam
ps an
d W
orkh
old
ing
ECONOMY PULL-ACTION LATCH CLAMPSPull ActionLatch Clamps
All models have a blue handle grip. Clamps are supplied with latch plates.
L
ON
K G
A
E
CH
DF
ØJ
Q
B
Cat. No. A B C D E F G H J K L N OQ
Min.Q
Max.Holding
Cap. Lbs.Drawing
MovementHookSize
PriceEach
ETC-12230 1.31 4.18 0.40 0.62 0.76 1.03 1.12 0.78 0.17 0.80 0.55 0.13 0.44 1.84 2.57 360 1.81 M4 8.67ETC-12310 1.91 6.56 0.48 0.78 1.25 1.52 1.75 1.01 0.28 1.00 0.79 0.17 0.50 2.53 3.69 700 1.75 M5 11.56ETC-12410 2.75 8.48 0.76 1.62 1.44 2.39 2.12 1.17 0.34 1.75 1.17 0.31 0.83 4.39 5.37 2000 2.50 M8 18.01
Pull ActionLatch Clamps
All models have a blue handle grip. Clamps are supplied with latch plates.
ØJ
L E
H F
K G
B
A
C D
O
ØN
Q
ETC-12750
ETC-12850
Cat. No. A B C D E F G H J K L N OQ
Min.Q
Max.Holding
Cap. Lbs.Drawing
MovementHookSize
PriceEach
ETC-12750 3.96 11.39 1.37 2.24 2.28 3.43 3.21 2.32 0.41 1.71 3.14 0.39 1.17 6.22 7.21 4000 3.50 M10 37.32ETC-12850 3.63 10.18 1.37 2.24 2.26 3.43 3.17 2.32 0.41 2.06 3.14 0.46 1.08 6.13 7.25 7500 2.19 M12 48.70
Pull ActionLatch Clamps
All models have a blue handle grip. Clamps are supplied with latch plates.
A
Q
M
H
O
Ø N
P
L
C
Ø J
K
Cat. No. A B C D E F G H J K L M N O PQ
Min.Q
Max.Holding
Cap. Lbs.Drawing
MovementHookSize
PriceEach
ETC-12240 2.22 3.15 0.57 0.51 0.87 1.02 1.39 1.00 0.21 0.86 0.54 3.43 0.12 0.2 0.43 0.54 1.20 500 1.53 M4 12.01ETC-12340 2.86 4.71 0.81 0.75 1.02 1.30 1.56 1.50 0.28 1.06 0.67 4.36 0.23 0.25 0.64 0.54 1.50 1000 2.00 M6 14.90ETC-12440 3.60 5.25 1.06 1.25 1.47 1.86 2.11 2.13 0.35 1.74 1.19 5.75 0.31 0.5 0.79 2.14 2.11 2000 2.50 M8 22.26
Pull ActionLatch Clamps
All models have a blue handle grip. B Q
Ø N Ø K
A C /O
D
E G
F Ø J
Cat. No. A B C D E F G J NQ
Min.Q
Max.Holding
Cap. Lbs.Drawing
MovementHookSize
PriceEach
ETC-12510 1.45 8.33 0.74 0.94 1.44 1.50 1.99 0.24 0.30 1.53 3.11 375 4.00 M8 8.83ETC-12710 2.17 11.46 0.96 1.25 1.97 1.86 2.61 0.35 0.39 2.70 3.44 750 5.38 M10 18.53ETC-12810 2.62 13.80 1.82 1.13 2.49 2.13 3.30 0.41 0.47 2.75 3.60 1000 6.13 M12 17.55
Pull ActionLatch Clamps
All models have a blue handle grip.
ØJ
FD
E G
N
K
O A
B
Cat. No. A B D E F G J K N OHolding
Cap. Lbs.Drawing
MovementBar
TypePriceEach
ETC-12010 1.88 8.40 0.75 1.22 1.38 1.72 0.28 0.60 0.12 1.59 375 4.00 Fixed Hook 9.83
B
Ø J
E G
D
F
0125.qxd 2/17/2010 3:05 PM Page 125
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!126
Cla
mp
s an
d W
ork
ho
ldin
gSTRAIGHT-LINE ACTION CLAMPS
See pages 136 and 137 for clamp accessories.
Series TC-601Holding Capacity: 100 Lbs.Plunger Travel: .63"
Series TC-6001-MHolding Capacity: 150 Lbs.Plunger Travel: .63"
Smallest of the straight-line toggle clamps. Ideal for electronicapplications and similar small fixturing. TC-601(shown) has an 8-32 nylon spindle (TC-105203). TC-601-SS has an 8-32 stainlesssteel spindle (TC-205943). TC-601-0 and TC-601-0SS have exter-nally threaded 1/4-20 plunger tips. TC-601-M has a M4 internalthread. TC-6001-M is a heavier duty version and has 50% greaterholding capacity. It is manufactured from heavy gauge materialand has a more flexible mounting base to enable side-mountingthe clamp. TC-6001-M has a M4 internal thread.
Note: Also available as power model TC-816. See page 141.
Discount 30 applies.
TC-601-0
TC-601TC-601, 601-0
TC-6001-M
TC-6001-M
PlungerType
PriceEach1-49Cat. No. A B C D E F G H J M N O P
SteelTC-601 1.19 2.62 .50 .63 .63 1.33 1.05 1.29 .17 .25 — — — 8-32 Tap 11.03TC-601-M 1.19 2.62 .50 .63 .63 1.33 1.05 1.29 .17 .25 — — — M4 Tap 13.90TC-601-0 1.19 2.86 .50 .63 .63 1.33 1.05 1.53 .17 1/4-20 — — — 1/4-20 Thd 12.00TC-6001-M 1.26 2.63 .50 .63 .63 1.54 1.23 1.10 .19 .28 .43 .33 .19 M4 Tap 15.63Stainless SteelTC-601-SS* 1.19 2.63 .50 .63 .63 1.33 1.05 1.29 .17 .25 — — — 8-32 Tap 23.59TC-601-0SS* 1.19 2.86 .50 .63 .63 1.31 1.05 1.53 .17 1/4-20 — — — 1/4-20 Thd 23.59TC-6001-MSS 1.26 2.63 .50 .63 .63 1.54 1.23 1.10 .19 .28 .43 .33 .19 M4 Tap 29.56*Handle does not have plastic grip
Series TC-602, 604, 624
Fully retractable locators, these models mount directly through amember by a jam nut on the work side, or flush by drilling andtapping the member. Locks in extended or retracted position.When flush mounted, plunger completely retracts from work area.An optional base mounting is available for TC-604 as TC-604106,and for TC-624 as TC-624108.
Discount 30 applies.
ØD
C
BA
PlungerTravel
TC-602
TC-604 TC-624 TC-6004
TC-624108Mounting Plate
TC-604106Mounting Plate
TravelB
HoldingCap. Lbs.
InternalThread
PriceEach1-49Cat. No. A C D Thread
SteelTC-602 3.14 .75 2.44 .37 5/8-18 200 1/4-20 x 5/8 15.60TC-602-MM 3.14 .75 2.44 .37 M16x1.5 200 M6 18.99TC-604 4.16 1.50 4.78 .44 3/4-16 300 5/16-18 x 1 17.45TC-604-MM 4.16 1.50 4.78 .44 M20x1.5 300 M8 23.92TC-6004 4.12 1.50 5.63 .50 3/4-16 450 5/16-18 31.53TC-6004-MM 4.12 1.50 5.63 .50 M20x1.5 450 M8 33.74TC-624 5.62 2.63 6.69 .62 1-14 700 3/8-16 x 11/4 36.72TC-604106 Optional Mounting Plate for TC-604 7.82TC-624108 Optional Mounting Plate for TC-624 9.66Stainless SteelTC-602-SS 3.14 .75 2.44 .38 5/8-18 200 1/4-20 x 5/8 51.54TC-604-SS 4.16 1.50 4.78 .44 3/4-16 400 5/16-18 x 1 46.14TC-624-SS 5.62 2.63 6.69 .62 1-14 700 3/8-16 x 11/4 96.36
TC-617Holding Capacity: 2,000 Lbs.Plunger Travel: 1"
Compact clamp with great holding capacity. Made from C-1008 orC-1010 low carbon, cold rolled steel with a black oxide finish.Hardened and ground pivots can be replaced. Forged clamp canbe cut or welded to suit fixturing or tooling needs. Plunger istapped 5/16-18 x 1” deep.
Discount 30 applies.Price Each
1-49Cat. No. A B C F G H MTC-617 5 7.00 1 1.75 .75 1 .50 105.47
Series TC-620Holding Capacity: 600 Lbs.Plunger Travel: 1-1/8”
TC-620 features a reverse handle action. As handle moves backand down to horizontal lock position, plunger moves forward. Canbe positioned for angular clamping by drilling base or may beused without base. TC-620 plungers are tapped 3/8-16 x 1” deep.TC-620-M plunger has M10 thread.
Discount 30 applies.
E
DØ.34
AB
ØF C
Price Each1-49Cat. No. A B C D E F
TC-620 2.25 1.67 11.70 1.63 1.63 .62 43.58TC-620-M 2.25 1.67 11.70 1.63 1.63 .62 56.81
0126.qxd 2/17/2010 3:05 PM Page 126
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 127
Clam
ps an
d W
orkh
old
ing
STRAIGHT-LINE ACTION CLAMPS
See pages 136 and 137 for clamp accessories.
Series TC-603Holding Capacity: 600 Lbs.Plunger Travel: 1-1/4"
This straight-line action toggle clamp has a large holding capacityfor its size. The TC-603 works well in confined areas because ofits small size and low height. TC-603 plunger is tapped 5/16-18 x1” deep for spindle. TC-603-M plunger has a M8x1.25 spindlethread.
Note: Also available as Power Model TC-803. See page 141.
Discount 30 applies.
D
E
A
C
B
7/32
F
Price Each1-49Cat. No. A B C D E F
SteelTC-603 3.28 .97 4.71 1.44 1.31 .44 20.81TC-603-M 3.28 .97 4.71 1.44 1.31 .44 24.05Stainless SteelTC-603-SS 3.28 .97 4.71 1.44 1.31 .44 47.57
Series TC-605, 615, 6015Holding Capacity: 300 Lbs.
For push and pull clamping. Furnished with red vinyl grip.Plungers on TC-605 and TC-615 are tapped 5/16-18 x 1” deepfor adjustment spindle. Base is heat treated for addedstrength. TC-615 is similar to TC-605 except it has reversehandle action. Plunger locks in the forward position only, asthe handle is moved downward. TC-605-M has M8 x 1.25spindle thread.
Discount 30 applies.
Travel
D
Ø J
B
F E G
A
CTC-6015-M
PlungerTravel
Price Each1-49Cat. No. A B C D E F
SteelTC-605 3.16 5.47 .97 1.38 1.63 .44 1.25 16.34TC-605-M 3.16 5.47 .97 1.38 1.63 .44 1.25 17.69TC-615 2.28 8.53 .97 1.38 1.63 .44 .97 26.03TC-6015-M 1.60 2.95 .50 1.75 .88 .38 .70 27.69Stainless SteelTC-6015-MSS 1.60 2.95 .50 1.75 .88 .38 .70 44.88
Series TC-6015-MR - Compact SizeToggle-Lock PlusHolding Capacity: 350 Lbs.Plunger Travel: .70”
Compact size allows use in confined areas and on small fixtures, where safety is a concern.Features a locking release lever which locks in the clamped position only.
Discount 30 applies.PlungerThread
Price Each1-49Cat. No. A B C D E F G H J M
SteelTC-6015-MR 1.60 2.95 .50 1.75 .88 2.25 1.25 .70 .22 .38 M6 x 1.0 36.61Stainless SteelTC-6015-MRSS 1.60 2.95 .50 1.75 .88 2.25 1.25 .70 .22 .38 M6 x 1.0 48.70
TC-603-RToggle-Lock PlusHolding Capacity: 600 Lbs.Plunger Travel: 1.25”
For use in confined areas. Theergonomic handle is slanted forwardto provide an adequate grip. Clamplocks in both the extended andretracted positions while the releaselever secures the clamp in theextended position only. Plunger istapped for 5/16-18 adjustmentspindle or detail.
Discount 30 applies.Price Each
1-49Cat. No. A B C D E F G H J MTC-603-R 3.42 4.69 .97 1.44 1.31 2.00 1.86 2.16 .27 .44 38.88
0127.qxd 2/23/2010 1:27 PM Page 127
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!128
Cla
mp
s an
d W
ork
ho
ldin
gSTRAIGHT-LINE ACTION CLAMPS
See pages 136 and 137 for clamp accessories.
TC-606Holding Capacity: 450 Lbs.Plunger Travel: 1-1/2”
Features an unusual 180° swiveling handle and linkage. Canbe mounted in many positions with the handle remaining in anup-right or other convenient position. This feature along with anarrow base permits use where other clamps won’t fit. Heattreated base. TC-606 has a 7/16” diameter plunger tapped5/16-18 x 1” deep.
Discount 30 applies.Price Each
1-49Cat. No. A B C D E F G MTC-606 2.62 6.72 .88 1.25 .63 1.75 1.13 .44 30.59
Series TC-607Holding Capacity: 800 Lbs.Plunger Travel: 1-5/8"
Compact, low silhouette clamp locks in either extended orretracted position. Available with 1/2” round plunger or 1/2” squareplunger for multiple point locating. TC-607 and TC-607-SQ aredrilled and tapped 5/16-18 x 1” deep for spindle and TC-607-M.
Discount 30 applies.
E
ED
9/32" Dia.
B
C
A
PlungerType
Price Each1-49Cat. No. A B C D E
TC-607 3.59 .69 6.02 1.38 1.63 1/2 dia. 31.93TC-607-M 3.59 .69 6.02 1.38 1.63 1/2 dia. 33.65TC-607-SQ 3.59 .69 6.02 1.38 1.63 1/2 sq. 49.86
TC-608Holding Capacity: 850 Lbs.Plunger Travel: 1-5/8”
Low profile clamp with cast base. Plunger locks in either retractedor extended positions. Plunger is tapped for 3/8-16 adjustmentspindle.
Discount 30 applies.Price Each
1-49Cat. No. A B C D E F G H J M
TC-608 4.04 6.13 1.25 1.63 1.63 2.31 2.25 3.00 .33 .62 36.66
Series TC-609Holding Capacity: 300 Lbs.Plunger Travel: 1-1/4"
Locks in either extended or retracted positions. The 1/2” diameterplunger is drilled and tapped 5/16-18 to accept customized fixtureor neoprene tipped spindle. Plunger retracts completely to clearthe work area. Available with a straight base,TC-609-B or aflanged base TC-609.
Discount 30 applies.
TC-609
Price Each1-49Cat. No. A B C D E F G H J M
TC-609 3.25 5.48 .97 1.38 1.62 3.60 2.19 1.88 .27 .50 18.87TC-609-B 4.28 5.48 1.56 1.38 — 3.60 .25 1.88 .27 .50 19.14
0128.qxd 2/22/2010 10:29 AM Page 128
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 129
Clam
ps an
d W
orkh
old
ing
STRAIGHT-LINE ACTION CLAMPS
See pages 136 and 137 for clamp accessories.
Series TC-630, 640
A
C
PlungerTravel
D
ø.41
E
B
F
D
Forged alloy steel base designed for heavy duty service. Ruggedhandle is red vinyl coated for easy operation. Low silhouette,maximum capacity for the size. Plunger locks in extended orretracted position. TC-630 plunger is tapped 3/8-16 x 1-1/4” deepfor adjustment spindle. TC-640 plunger is tapped 1/2-13 x 2” deepfor adjustment spindle. TC-630-M has M10 thread.
Note: Also available as Toggle-Lock Plus Model TC-630-R. See page129. For Power Model TC-830. See page 141.
Discount 30 applies.
D E
ø.34
EF
TC-630 TC-640
HoldingCapacity
(Lbs.)PlungerTravel
Price Each1-49Cat. No. A B C D E F
TC-630 3.09 .81 7.03 1.38 1.63 .63 2,500 2 39.04TC-630-M 3.09 .81 7.03 1.38 1.63 .63 2,500 2 41.79TC-640 4.38 1.25 12.66 3.56 2.12 .87 7,500 4 107.61
TC-630
Series TC-610Holding Capacity: 800 Lbs.
TC-610 features balanced construction for rigid holding andassured long life. Plunger tip is drilled and tapped 3/8-16 x 1”deep for spindle. TC-610-M has M10 thread.
Discount 30 applies.BaseType
Price Each1-49Cat. No. A B C D E F
TC-610 4.38 1.70 6.72 1.63 1.63 .63 Flanged 29.31TC-610-M 4.38 1.70 6.72 1.63 1.63 .63 Flanged 33.81
TC-650 Holding Capacity: 16,000 Lbs.Plunger Travel: 3"
Largest holding capacity of the straight line action clamps. TC-650is precision built with forged alloy steel handle and base. Base isheat treated for added strength. Snap ring pivot pin constructionallows easy removal of plunger even after unit is mounted. TC-650plunger is tapped 5/8-11 x 2” deep.
Note: Also available as Power Model TC-850. See page 141.
Discount 30 applies.Price Each
1-49Cat. No. A B C D E G H J MTC-650 4.88 11.25 2.25 2.75 2.25 3.13 6.25 .41 1 124.91
TC-95030, 95040, 95050, 95060
Low profile to use where overhead clearance is a problem.Handle can be easily disassembled and re-assembled in thereverse position, allowing more flexibility. Plunger is tapped withmetric thread.
Discount 30 applies.
A
C
B
TRAVELPLUNGER
H D D
F
E GM
J
TC-95030
Price Each1-49Cat. No. A B C D E F G H J M
TC-95030 2.32 4.13 .31 .98 .98 3.07 1.38 .20 .22 .39 32.08TC-95040 3.00 5.91 .39 1.38 1.38 4.33 1.97 .33 .26 .55 39.50TC-95050 3.50 7.52 .55 1.77 1.77 5.59 2.56 .39 .33 .75 50.97TC-95060 4.08 9.17 .63 2.17 2.17 6.73 3.00 .39 .41 .87 66.35
HoldingCapacity
PlungerTravel
PlungerThreadCat. No.
TC-95030 550 .98 M6TC-95040 1,100 1.50 M8TC-95050 1,650 1.97 M12TC-95060 3,965 2.36 M12
TC-630-RToggle-Lock PlusHolding Capacity: 2,500 Lbs.Plunger Travel: 2”
Locking release lever locks into the rugged forged steel base.Large handle pad for greater comfort. Plunger is tapped 3/8-16 x1-1/4” deep to accommodate spindle assembly.
Discount 30 applies.Price Each
1-49Cat. No. A B C D D1 E F G H J M
TC-630-R 3.06 7.03 .81 1.38 1.63 1.63 5.03 2.30 2 .34 .62 77.06
0129.qxd 2/17/2010 3:06 PM Page 129
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!130
Cla
mp
s an
d W
ork
ho
ldin
g
ETC-13485
ETC-13585
ECONOMY STRAIGHT-LINE ACTION CLAMPSStraight-LineAction Clamp
All models have a blue handle grip. Spindle assemblies are supplied.
F
E G
D ØJ
M
C C
H
ØJ B
A A ETC-13100
ETC-13180
Cat. No. A B C D E F G H J MHolding
Cap. Lbs.PlungerTravel
SpindleSize
PriceEach
ETC-13100 5.04 6.82 1.75 1.63 1.58 2.25 2.20 4.23 0.34 0.62 800 1.63 3/8-16 X 1.25 19.60ETC-13180 5.80 6.79 2.36 1.63 — 2.25 0.24 4.23 0.34 0.62 800 1.63 3/8-16 X 1.25 32.96
Straight-LineAction Clamp
All models have a blue handle grip. Spindle assemblies are supplied.
C
B
A
H
D D1F
E G
Ø M
Ø J
Cat. No. A B C D D1 E F G H J MHolding
Cap. Lbs.PlungerTravel
SpindleSize
PriceEach
ETC-13070 3.28 6.10 0.68 1.38 1.63 1.63 4.30 2.18 1.86 0.28 0.51 800 1.63 5/16-18 X 1.00 22.54ETC-13300 2.93 7.06 0.88 1.38 1.39 1.63 5.25 2.24 1.82 0.35 0.63 2500 2.00 3/8-16 X 1.25 28.39
Straight-LineAction Clamp
All models have a blue handle grip. Spindles are supplied.B
A
C
Ø M
C
A
H
D
E G
Ø J
F
M
Cat. No. A B C D E F G H J MHolding
Cap. Lbs.PlungerTravel
SpindleSize
HandleType
PriceEach
ETC-13030 3.34 3.64 0.98 1.44 1.32 2.30 1.85 2.03 0.23 0.43 600 1.25 5/16-18 X 1.00 45° 15.11ETC-13485 4.19 6.41 1.25 1.62 1.63 2.33 2.25 3.13 0.33 0.63 850 1.65 3/8-16 X 1.25 45° 24.53ETC-13415 4.95 9.39 1.78 1.99 2.00 2.89 2.48 5.00 0.34 0.70 1500 2.36 1/2-13 X 2.00 45° 15.53ETC-13585 4.75 6.41 1.25 1.60 1.62 2.33 2.25 3.14 0.33 0.62 850 1.65 3/8-16 X 1.25 90° 27.72ETC-13515 6.93 9.38 1.83 2.00 2.02 2.85 2.82 5.75 0.35 0.70 1500 2.36 1/2-13 X 2.00 90° 27.72
Straight-LineAction Clamp
All models have a blue handle grip. Spindles are supplied.
F
D
ØJ
E G
A
H
C
B
ØM
Cat. No. A B C D E F G H J MHolding
Cap. Lbs.PlungerTravel
SpindleSize
PriceEach
ETC-13090 4.10 5.00 0.85 1.57 1.33 3.27 1.95 1.71 0.26 0.47 300 1.25 5/16-18 X 1.00 12.65
0130.qxd 2/17/2010 3:08 PM Page 130
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 131
Clam
ps an
d W
orkh
old
ingECONOMY STRAIGHT-LINE ACTION CLAMPS
Straight-LineAction Clamp
All models have a blue handle grip. Spindles are supplied.
E G
M
J
FD
A
C
HB
ETC-13010
ETC-13011
Cat. No. A B C D E F G H J MHolding
Cap. Lbs.PlungerTravel
SpindleSize
PriceEach
ETC-13010 1.57 2.67 0.52 0.63 0.61 1.31 1.07 1.35 0.17 0.25 100 .63 #8-32 X .50 DP 7.79ETC-13011* 1.59 2.85 0.57 0.63 0.61 1.31 1.07 1.53 0.17 1/4-20 100 .63 1/4-20 X .50 LG 8.03
*External thread
Straight-LineAction Clamp
All models have a blue handle grip. Spindles are supplied.
C H
B
A
J L (FLATS)
Ø F
K
D
Cat. No. A B C D F H J K LHolding
Cap. Lbs.PlungerTravel
SpindleSize
BaseType
PriceEach
ETC-13020 3.06 2.67 0.48 1.03 0.37 0.81 0.58 0.26 0.94 200 .75 1/4-20 X .63 Through-Hole 10.97ETC-13040 4.16 4.26 0.63 1.28 0.43 1.57 0.73 0.25 1.17 300 1.50 5/16-18 X 1.00 Through-Hole 12.29ETC-13240 5.43 6.73 0.88 1.86 0.63 2.80 1.05 0.35 1.59 700 2.63 3/8-16 X 1.25 Through-Hole 24.60
Straight-LineAction Clamp
All models have a blue handle grip. Spindles are supplied.
FD
ØJ
E G
ØM
A
C
HB
Cat. No. A B C D E F G H J MHolding
Cap. Lbs.PlungerTravel
SpindleSize
PriceEach
ETC-13050 3.14 5.45 0.98 1.38 1.64 3.55 2.22 1.90 0.22 0.47 300 1.25 5/16-18 X 1.00 11.53
0131.qxd 2/17/2010 3:08 PM Page 131
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!132
Cla
mp
s an
d W
ork
ho
ldin
g
TC-2010 TC-2020
TC-2040 TC-2050
STRAIGHT-LINE ACTION CLAMPSDesigned for quick action where there are wide size variations from part to part or where the opening and closing motions need to belong. In operation, the plunger is pushed forward until it contacts the work piece. The locking lever is then rotated clockwise whichadvances the plunger and simultaneously locks it with the collet action. Short stroke models are single handled and long stroke models(with interchangeable length plungers) have a separate locking handle. All dimensions below are metric. Accessory plungers for longstroke models and plunger tips are sold separately.
TC-1000Through Hole Mount - Hand Knob
10
M24 x 1.5 Metric
35 Dia.
PlungerTappedThread
mm
PlungerDia.mm
StrokeLgth.mm
PriceEachCat. No. De-Sta-Co
HandleType
Interchg.Plungers
HoldingCap. Lbs.
TC-1000 G-082/40 8 M5x0.80 40 Hand Knob No 300 174.77
TC-1010Through Hole Mount - Lever
23
80R
40
12
1812
M30 x 1.5 Metric
PlungerTappedThread
mm
PlungerDia.mm
StrokeLgth.mm
PriceEachCat. No. De-Sta-Co
Interchg.Plungers
HoldingCap. Lbs.
TC-1010 G-121/45 12 M6x1.00 45 No 600 238.51
TC-2000, 2030Foot Mount - Hand Knob
30.5
55
6.5 Dia. 2 Holes8R
52
44
25
1010
18
6
40
TC-2030TC-2000
PlungerTappedThread
mm
PlungerDia.mm
StrokeLgth.mm
PriceEachCat. No. De-Sta-Co
HoldingCap. Lbs.
TC-2000 FO-082/40 8 M5x0.80 40 300 174.77TC-2030 FO-122/45 12 M6x1.00 45 600 215.25
TC-2010, 2020, 2040, 2050Foot Mount - Locking Lever
23
115R
1720
74
3058
7090
26R
23 40
12
M6
115
4220
2,5
44Stroke
12
40
3 2
12
TC-2010, 2020 TC-2040, 2050
Cat. No. De-Sta-Co
PlungerDia.mm
PlungerTappedThread
mm
StrokeLgth.mm
Interchg.Plungers
HoldingCap. Lbs.
PriceEach
TC-2010 FO-121/45 12 M6x1.00 45 No 600 225.59TC-2020* FO-120/- 12 M6x1.00 — Yes 600 197.72TC-2040 FO-161/60 16 M8x1.25 60 No 2,000 291.80TC-2050* FO-160/- 16 M8x1.25 — Yes 2,000 250.90*Long stroke models. Attached lever. Interchangeable plungers soldseparately.
TC-3000, 3010, 3020, 3030Flange Mount - Locking Lever
1218
43.5
40
6
12
30
23
80R
52
8R 6.5 Dia. 2 Holes
58.8
20
46
40
14
14
30
23
115R
51
10R
17
TC-3010
TC-3020
TC-3000TC-3010
TC-3020TC-3030TC-3030
Cat. No. De-Sta-Co
PlungerDia.mm
PlungerTappedThread
mm
StrokeLgth.mm
Interchg.Plungers
HoldingCap. Lbs.
PriceEach
TC-3000 FL-121/45 12 M6x1.00 45 No 600 225.59TC-3010* FL-120/- 12 M6x1.00 — Yes 600 203.70TC-3020 FL-161/60 16 M8x1.25 60 No 2,000 291.80TC-3030* FL-160/- 16 M8x1.25 — Yes 2,000 257.09*Long stroke models. Attached levers. Interchangeable plungers soldseparately.
Series TC-4000Plungers for Long Stroke Models
CA
B
D
Cat. No. De-Sta-CoA
mmB
mmC
mmD
mmStroke
mmPriceEach
TC-4000 12/100 198 12 29 M6x1.00 100 23.31TC-4010 12/200 298 12 29 M6x1.00 200 32.45TC-4020 12/300 400 12 29 M6x1.00 300 36.38TC-4030 16/100 215 16 35 M8x1.25 100 30.61TC-4040 16/200 315 16 35 M8x1.25 200 35.70TC-4050 16/300 416 16 35 M8x1.25 300 46.73
Series TC-5000Swivel Face Thrust Pads for Plunger Tips
A
7 MAX. TILT
B D
C
Thd.D
mmCat. No. De-Sta-CoA
mmB
mmC
mmPriceEach
TC-5000 K508 6 9.2 8 M5x0.80 14.12TC-5010 K612 8.5 12.5 10 M6x1.00 12.55TC-5020 K816 10 14.8 14 M8x1.25 15.59
0132.qxd 2/17/2010 3:09 PM Page 132
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 133
Clam
ps an
d W
orkh
old
ing
STRAIGHT-LINE ACTION CLAMPSDesigned for quick action where there are wide size variations from part to part or where the opening and closing motions need to belong. In operation, the plunger is pushed forward until it contacts the work piece. The locking lever is then rotated clockwise whichadvances the plunger and simultaneously locks it with the collet action. See pages 136 and 137 for accessories.
See pages 136 and 137 for clamp accessories.
Series TC-FRF, FRL
To operate:• Slide spindle bar forward to contact the work piece• Turn the locking lever clockwise to engage the locking mechanism• Turn knob handle to “fine” to adjust the clamping force• After operation is finished, turn the locking lever counter-clockwise to disengage locking mechanism
Discount 30 applies.
Series FRF Series FRL
Cat. No.HoldingCapacity Stroke A B C D E F G H J
Price Each1-49
TC-FRF-12 5,500 0 - 33/8 6.46 1.26 .67 .75 1.97 1.50 1.30 .24 .22 68.84TC-FRF-16 11,000 0 - 55/16 9.25 1.69 .87 .98 2.54 1.91 1.65 .31 .28 84.54TC-FRL-12 5,500 0 - 33/8 6.46 1.26 .63 .75 2.17 1.77 .79 .24 .22 68.84TC-FRL-16 11,000 0 - 55/16 9.25 1.69 .79 .98 2.56 2.09 1.10 .31 .28 84.54
SQUEEZE ACTION PLIER CLAMPSSeries TC-325Holding Capacity: 800 Lbs. (max)Jaw Moves: 90°, Handle Moves: 50°
Designed for attachment by welding front of top of base tocontainer or cover. Forged alloy steel jaw moves 90° to clearcompletely. Red vinyl grip provides easy operation and good-looking appearance. TC-325 is furnished with M12 hex headspindle (TC-325203-M) and lock nut. TC-325-SS furnished withstainless steel M12 hex head spindle (TC-325943-M) and lock nut.
Discount 30 applies.
Cat. No. A B C D E F G HPrice Each
1-49SteelTC-325 8.68 2.62 1.78 .75 2.94 1.25 .50 .27 24.50Stainless SteelTC-325-SS 8.68 2.62 1.78 .75 2.94 1.25 .50 .27 66.43
TC-345Holding Capacity: 800 Lbs. (max.)Jaw Moves: 86°, Handle Moves: 60°
Designed for bolting or welding to a fixture at any point alongbase, or base can be cut off for end welding. This model hasa forged steel jaw with M10 swivel foot spindle assembly(TC-468206-M).
Discount 30 applies.
Cat. No. B C D FSpindleThread
Price Each1-49
TC-345 6.56 10.12 .69 2.69 M10 57.18
0133.qxd 2/22/2010 10:32 AM Page 133
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!134
Cla
mp
s an
d W
ork
ho
ldin
gSQUEEZE ACTION PLIER CLAMPS
See pages 136 and 137 for clamp accessories.
TC-425, 435, 445, 470
These high strength squeeze action clamps are ideal for ruggedclamping applications. Made from SAE 1045 steel for strength.Two way trigger release allows for fast unclamping. Supplied withspindle.
Discount 30 applies.
TC-425
TC-435
TC-445
TC-470
Cat. No.HoldingCapacity A B C D E F
SpindleSupplied
Price Each1-49
TC-425 500 1.63 5.55 1.10 .39 2.56 1.83 (1) M6 x 1.0 21.68TC-435 500 1.63 5.55 1.77 .39 3.23 1.83 (2) M6 x 1.0 22.99TC-445 2,000 2.00 8.27 2.09 .63 4.41 2.76 (1) M10 x 1.0 34.75TC-470 2,000 2.00 8.27 3.35 .63 5.63 2.76 (2) M10 x 1.0 77.49
Series TC-441Holding Capacity: 350 Lbs.
TC-441 has a M8 adjustment spindle (TC-441203-M). TC-441-2has two adjustment spindles (TC-461203-M). Maximum jawopening is 2-55/64”.
Discount 30 applies.
Cat. No. A B C D E FPrice Each
1-49TC-441 1.97 6.06 1.25 .50 2.86 1.77 21.41TC-441-2 1.97 6.06 1.25 .50 2.86 1.77 23.47
TC-443Holding Capacity: 500 Lbs.
Compact design features wide angle 64° jaw opening. Two-waytrigger release is standard. TC-443 comes with M8 hex headspindle assembly (TC-441203-M).
Discount 30 applies.
Cat. No. A B C D F ThreadPrice Each
1-49TC-443 2.47 6.70 1.39 .56 1.88 M8 97.07
TC-431Holding Capacity: 100 Lbs.
Tempered spring-steel jaws have exceptional 2-15/16” jawdepth. TC-431 has single neoprene tipped adjustment spindle(TC-424208-M). Maximum opening is 3-1/16”.
Discount 30 applies.
AC
431-2
431
E
D
B
F
Cat. No. A B C D E FPrice Each
1-49TC-431 2.41 6.88 .75 .50 3.06 2.92 21.75
0134.qxd 2/17/2010 3:09 PM Page 134
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 135
Clam
ps an
d W
orkh
old
ing
SQUEEZE ACTION PLIER CLAMPS
See pages 136 and 137 for clamp accessories.
TC-463, 491, 482, 484, 486
Most models have trigger release for easy one hand operation. Ideal for clamping and fixturing, holding and processing, etc.
Discount 30 applies.
TC-463
TC-491
HoldingCapacity
SpindleType
No. ofSpindles
Spindle(s)Furnished
TriggerRelease
E SpindleThread
Price Each1-49Cat. No. A B C D
TC-463 700 Std. 2 TC-468206-M & TC-210203-M Yes 2.69 3.00 8.50 2.72 M10 36.34TC-491 850 Std. 1 TC-491203-M Yes 2.87 1.00 10.10 3.50 M10 86.75TC-482 1,200 Std. 1 TC-468206-M Yes 2.80 1.70 9.19 2.56 M10 43.28TC-484 1,200 Std. 2 TC-468206-M & TC-210203-M Yes 2.69 3.83 9.06 2.56 M10 44.99TC-486 1,000 Std. 2 TC-240203-M Yes 2.88 6.00 9.22 2.56 M10 48.27
TC-462
Furnished with M10 swivel-foot adjustment spindle (TC-468206-M)and two-way trigger release. Forged alloy steel components, clevistype construction with stainless steel rivets.
Discount 30 applies.Holding
Cap. Lbs.Price Each
1-49Cat. No. A B C D E FTC-462 2.69 8.47 1.75 .69 4.10 2.78 700 31.69
Series TC-424Holding Capacity: 200 Lbs.
Smallest of the forged alloy steel squeeze action clamps.TC-424 has a single M6 neoprene tipped adjustment spindle(TC-424208-M). TC-424-2 has two neoprene tipped adjustmentspindles (TC-431208-M). Maximum jaw opening is 2-1/16”.
Discount 30 applies.
TC-424-2
Price Each1-49Cat. No. A B C D E F
TC-424 1.94 4.75 1 .50 2.06 1.08 16.22TC-424-2 1.94 4.75 1 .50 2.06 1.08 16.87
TC-453Holding Capacity: 1,000 Lbs.
Features a special action to provide full 88° clearance in theopen position. This is particularly suited for clamping parts andassemblies where fast action, max. jaw clearance is essential.Two-way trigger release. Furnished with one M10 swivel footassembly (TC-468206-M) and one M10 hex head spindleassembly (TC-491203-M).
Discount 30 applies.Price Each
1-49Cat. No. A B C D F ThreadTC-453 2.77 8.56 3 .69 2.5 M10 43.80
TC-468Holding Capacity: 700 Lbs.
Furnished with M10 swivel foot adjustment spindle assembly(TC-468206-M). Forged alloy steel components and clevis typeconstruction with stainless steel rivets.
Discount 30 applies.Price Each
1-49Cat. No. A B C D E FTC-468 2.66 8.47 1.75 .69 4.10 2.75 43.68
0135.qxd 3/5/2010 3:00 PM Page 135
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!136
Cla
mp
s an
d W
ork
ho
ldin
gCLAMP ACCESSORIES
Hex Head Assemblies with Locknuts
Discount 36 applies.
TC-105203
TC-205943
Cat. No. Thread Thread Lgth. OALPrice Each
1-99Steel - InchTC-105203 8-32 Nylon Bolt .75 .84 .92TC-305203 10-32 1.00 1.09 .92TC-205203 1/4-20 1.69 1.88 1.15TC-202203 1/4-20 3.00 3.13 1.15TC-461203 5/16-18 .81 1.00 1.22TC-441203 5/16-18 1.75 1.94 1.51TC-207203 5/16-18 2.50 2.75 1.12TC-491203 3/8-16 1.25 1.50 1.22TC-210203 3/8-16 2.75 3.00 1.23TC-240203 3/8-16 4.00 4.25 2.15TC-527203 3/8-16 5.00 5.25 2.06TC-325203 1/2-13 2.50 2.75 1.89TC-220203 1/2-13 3.00 3.31 2.11TC-250203 5/8-11 4.00 4.38 3.44Steel - MetricTC-325203-M M12 2.56 2.83 2.00TC-210203-M M10 2.76 3.03 1.40TC-240203-M M10 4.00 4.25 2.41TC-441203-M M8 1.75 1.94 1.49TC-461203-M M8 .81 1.00 1.51TC-491203-M M10 1.25 1.50 1.65Stainless Steel - InchTC-205943 8-32 .75 .86 1.40TC-213943 8-32 1.03 1.13 2.67TC-201943 10-32 1.03 1.13 1.52TC-202943 1/4 -20 1.38 1.50 1.52TC-207943 5/16-18 2.31 2.50 3.56TC-237943 3/8-16 2.25 2.50 3.94
Flat-Tip Bonded Assemblies with Neoprene Cap and Locknuts
Discount 36 applies.
Flat Tip
Low Cushion
Cat. No. Thread Thread Lgth. OALPrice Each
1-99Flat Tip - InchTC-201208 10-32 1.00 1.38 1.52TC-431208 1/4-20 .63 1.00 1.69TC-424208 1/4-20 1.13 1.50 1.69TC-202208 1/4-20 1.25 1.63 1.82TC-215208 1/4-20 1.66 2.19 2.15TC-225208 5/16-18 1.50 2.25 2.15TC-507208 5/16-18 2.31 3.06 2.18TC-240208 3/8-16 2.31 3.31 2.85TC-527208 3/8-16 2.50 3.50 3.15TC-235208 3/8-16 4.88 5.88 3.83TC-247208 1/2-13 2.69 4.00 4.29TC-267208 5/8-11 3.63 5.00 5.08Flat Tip - MetricTC-102208-M M4 1.00 1.25 1.80TC-431208-M M6 0.63 1.00 1.69TC-424208-M M6 1.13 1.50 1.69TC-202208-M M6 1.25 1.73 1.95TC-215208-M M6 1.66 2.19 2.18TC-225208-M M8 1.50 2.25 2.18TC-507208-M M8 2.31 3.06 2.30TC-240208-M M10 2.31 3.31 3.02TC-235208-M M10 4.88 5.88 4.22TC-247208-M M12 2.68 3.82 5.95Flat Tip Low Cushion w/ Locknuts - MetricTC-205208-M M4 .76 .87 1.90TC-201208-M M4 1.06 1.26 1.57TC-213208-M M5 1.14 1.34 1.59TC-305208-M M5 .94 1.14 1.82TC-307208-M M8 1.34 1.69 2.09
Cone-Tip Bonded Neoprene Cap Assemblies with Locknuts
Discount 36 applies.
Cat. No. Thread Thread Lgth. OALPrice Each
1-99TC-305208 10-32 1.00 1.44 1.82TC-213208 1/4-20 1.50 2.13 2.22TC-509208 5/16-18 2.25 2.94 2.30TC-519208 5/16-18 4.75 5.38 3.21TC-220208 3/8-16 2.00 2.88 2.62TC-210208 3/8-16 2.50 3.44 2.47
Plunger-Matic Assemblies
Automatically compensates for variations in part thicknesses. Tobe mounted to plunger clamps.
Discount 36 applies.ThreadLgth.
Lbs.Pressure*
Max. SpringCompression
Price Each1-99Cat. No. Thread OAL
TC-905 5/16-18 .75 2.50 135 3/16 15.21TC-920 3/8-16 1.13 3.63 308 3/8 20.08*Per 1/8” deflection
Swivel Foot Assemblies with Locknuts
Discount 36 applies.
Cat. No. Thread Thread Lgth. OALPrice Each
1-99InchTC-207206 1/4-20 1.50 2.38 3.83TC-507206 5/16-18 1.94 2.75 4.06TC-468206* 3/8-16 2.00 3.00 4.29TC-210206 3/8-16 2.44 3.38 4.63TC-250206 1/2-13 3.50 4.63 7.18MetricTC-468206-M M10 2.00 3.00 4.34*Threaded to the foot with knurled end
Neoprene Swivel Foot Assemblies
Discount 36 applies.
Cat. No. Thread Thread Lgth. OAL Pad Dia.Price Each
1-99TC-207209 1/4-20 1.50 2.63 1.00 8.16TC-507209 5/16-18 1.94 3.00 1.50 9.08TC-210209 3/8-16 2.44 3.63 2.00 9.78
0136.qxd 2/17/2010 3:10 PM Page 136
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 137
Clam
ps an
d W
orkh
old
ing
CLAMP ACCESSORIESNeoprene Caps
Slip on the heads of thehex head spindles.
Discount 36 applies.
Cat. No. OD ID Height For Spindle Dia.Price Each
1-99TC-215119 .63 .25 .44 1/4 .51TC-225119 .75 .31 .50 5/16 .56TC-235119 .78 .38 .53 3/8 .66
Neoprene Caps
Designed to fit over thethreaded end of a spindle.
Discount 36 applies.
Cat. No. For Spindle Dia.Price Each
1-99TC-424107 7/32 .51TC-235110 11/32 .64
Latch Plates
Discount 36 applies.
A B C D
For Use w/ Clamp
Price Each1-99
For Usew/ Clamp
Price Each1-99Cat. No. Style Cat. No. Style
Steel Stainless SteelTC-323104-M A TC-323 1.97 TC-323104-MSS A TC-323-SS 2.90TC-324101 B TC-324 1.97 TC-331905 A TC-331-SS 3.88TC-331005 A TC-331, 331-R 2.11 TC-341905 A TC-341-SS 10.65TC-334101 B TC-334 2.47TC-341005 A TC-341,341-R 3.29TC-344101 B TC-344 3.15TC-375509 C TC-375-B 6.24TC-385102 D TC-375, TC-385 16.93
Hook Assemblies with Locknuts
Discount 36 applies.
U-Hook J-Hook
For Use w/ Clamp
PriceEach1-99
For Usew/ Clamp
PriceEach1-99Cat. No. Style Cat. No. Style
Steel Stainless SteelTC-323215 U-Hook TC-323 3.33 TC-323915 U-Hook TC-323-SS 7.49TC-324215 U-Hook TC-324 3.15 TC-331915 U-Hook TC-331-SS 6.67TC-331215 U-Hook TC-331 2.78 TC-341915 U-Hook TC-341-SS 11.06TC-334215 U-Hook TC-334 3.02 TC-344915 U-Hook TC-344-SS 11.06TC-341215 U-Hook TC-341 4.81 TC-330915* J-Hook TC-330-SS 4.45TC-344215 U-Hook TC-344 4.86 TC-351915 J-Hook TC-351-SS 6.66TC-375215 U-HookTC-375, 375-R 6.66TC-385215 U-Hook TC-385 7.57TC-330215*J-Hook TC-330 2.14TC-371215 J-Hook TC-371 5.09*Supplied with two jam nuts
Polyurethane Caps
Internally threaded to screw on to spindle. High oil and abrasionresistance. Good memory.
Discount 36 applies.
Cat. No. For Spindle Dia.Price Each
1-99Flat TipTC-215219 1/4 1.28TC-225219 5/16 1.28TC-235219 3/8 1.43Cone TipTC-215319 1/4 1.28TC-225319 5/16 1.26TC-235319 3/8 1.43
Flanged Washers for U-Bar Clamps
Discount 36 applies.PriceEach1-99
PriceEach1-99Cat. No.
Use w/ Spindle Cat. No.
Usew/ Spindle
Steel Stainless SteelTC-102111 No.10 Spindle .27 TC-102911 No.10 Spindle .35TC-105106 No. 8 Spindle .23 TC-507907 5/16 Spindle .76TC-215105 1/4 Spindle .29 TC-235906 3/8 Spindle 1.04TC-507107 5/16 Spindle .33TC-235106 3/8 Spindle .40TC-247109 1/2 Spindle .76TC-267102 5/8 Spindle 1.09
Bolt Retainers for Clamps with Solid Hold Down Bars
Discount 36 applies.
Cat. No. DescriptionPrice Each
1-99TC-207105 1.25 Bolt Retainer for 5/16 Spindle 1.57TC-210114 1.50 Bolt Retainer for 3/8 Spindle 2.30TC-247110 1.63 Bolt Retainer for 1/2 Spindle 3.76TC-110122 1.88 Bolt Retainer for 5/8 Spindle 6.62TC-250121 1.88 Bolt Retainer for 1/2 Spindle 5.09
Ergonomic Grips
Provides a safe and comfortable grippingsurface for vertical hold down clamps. Theadditional guard helps protect againstpotential pinch points.Item Description Price EachTC-202305 Fits 202, 2002 series clamps .94TC-207305 Fits 207, 2007 series clamps 1.58
0137.qxd 2/23/2010 12:46 PM Page 137
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!138
Cla
mp
s an
d W
ork
ho
ldin
gECONOMY CLAMP ACCESSORIES
Bolt Retainers
B
A
d F1
Cat. No. A B F1 d Price EachETC-19516 1.20 0.64 0.25 0.32 .80ETC-19380 1.47 0.74 0.33 0.41 .89ETC-19120 1.70 1.19 0.38 0.67 1.27
Swivel Foot Spindles
D
L1 L G
Hex Head Spindles
L1 L
D
G
Cat. No. D G L L1 Price EachETC-19338 0.55 3/8-16 3.23 3.00 1.02ETC-19310 0.74 1/2-13 3.31 3.00 1.73ETC-19112 0.43 1/4-20 1.65 1.50 .82ETC-19212 0.49 5/16-18 2.71 2.50 .89
Bonded Neoprene Spindles
L1
L
D
G
Cat. No. D G L L1 Price EachETC-19312 0.88 3/8-16 3.44 2.60 1.91ETC-19218 0.59 1/4-20 2.17 1.59 1.28ETC-19316 0.49 5/16-18 3.05 2.31 1.41
Cat. No. D G L L1 Price EachETC-19214 0.43 1/4-20 2.40 2.12 2.10ETC-19234 0.47 5/16-18 2.83 2.48 2.25ETC-19300 0.63 3/8-16 3.18 2.80 2.58
0138.qxd 2/22/2010 10:46 AM Page 138
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 139
Clam
ps an
d W
orkh
old
ing
PNEUMATIC HOLD-DOWN CLAMPSPneumatic cylinder provides the activating force for these over-center toggle clamps. Built to perform repetitive production operations.Portable and economical for use on short run jobs with temporary fixturing. Magnetic ring cylinders are used when there is a need tosense the open/close position of the cylinder. By adding a sensing switch, the position of the cylinder can be sensed. All these modelscome with magnetic ring for sensing capability. See page 147 for sensor options.
See page 147 for pneumatic clamp accessories.
Cyl.Area
(Sq. In.)
Max. InletPress atMax.MA
psig
Max.Mechanical Advantage
ESpindle
SizeCyl.Bore
Max. Hold.Cap. (Lbs.)
Exert. Force80 psig (Lbs.)
PriceEachCat. No. P A D F G H J Port Size
TC-812 .75 .44 80 150 2.7:1 to 3.8:1 98/135 5.60 1.50 1.02 10-32 .69 .94 .69 .17 10-32NF 96.15TC-802-U 1.13 .99 40 200 2:1 to 5:1 160/200 7.39 2.34 1.72 M6 1.06 1.06 .50 .22 1/8 NPT 103.93TC-807-S 1.13 .99 80 500 2:1 to 6.1 150/500 9.96 3.00 3.13 5/16 1.38 1.25 .75 .28 1/8 NPT 115.10TC-807-U 1.13 .99 55 350 3:1 to 6.1 150/350 9.21 3.00 2.50 5/16 1.38 1.25 .75 .28 1/8 NPT 115.10TC-8021 1.12 .994 105 390 2.2:1 to 1.3:1 100/175 9.31 2.19 2.25 .38 1.56 1.50 .79 .21 1/8 NPT 274.97TC-8071 1.50 1.77 105 450 2.4:1 to 4.2:1 250/450 10.93 2.59 2.50 .31 1.66 1.58 1.97 .28 1/8 NPT 323.86TC-8101 2.00 3.141 110 700 2.0:1 to 1.1:1 275/500 15.30 3.50 4.00 .38 2.87 2.20 3.54 .34 1/4 NPT 450.97TC-810-S 1.50 1.77 80 750 2.9:1 to 5:1 400/700 12.13 3.79 3.48 .38 1.80 1.78 1.25 .33 1/8 NPT* 195.95TC-810-U 1.50 1.77 70 600 2.9:1 to 5:1 400/600 12.28 3.79 3.58 — 1.80 1.78 1.25 .33 1/8 NPT* 187.46TC-846 1.50 1.77 125 750 3.5:1 to 5.6:1 500/750 10.50 3.63 2.13 — 1.63 1.50 1.00 .28 1/8 NPT* 335.91TC-847-S 2.00 3.14 80 1,000 1.8:1 to 4:1 450/1000 16.00 4.34 4.88 .50 2.25 1.78 1.25 .34 1/8 NPT* 341.75TC-847-U 2.00 3.14 60 800 1.8:1 to 4:1 450/750 16.00 4.34 4.88 — 2.25 1.78 1.25 .34 1/8 NPT* 341.75TC-858 2.50 4.90 200 4,000 2.3:1 to 4:1 900/1,600 18.09 7.12 4.88 — 3.84 2.75 4.25 .41 1/8 NPT* 436.66*Restrictor fittings are supplied that must be installed on clamp cylinder
TC-812
Smallest of hold-down models,this miniature clamp is the powerversion of TC-201. The 10-32spindle is adjustable for heightand location along the bar.Cylinder has built in speedcontrols for smooth operation.Clamp and base are stainlesssteel. Bar opens 90°. TC-812uses the TC-810156 reed switch.
A
D
P
F
H
G
J (Screw Size)E Spindle Size
TC-802-U
TC-802 provides 200 lbs. holdingcapacity in a package less than7” long. Threaded spindle isadjustable to accommodate workpiece height and is neoprenetipped for part protection. Doubleacting power cylinder has built-inspeed control (restriction) andneeds only to be hooked up to a
controlled air or hydraulic power source. Hold down bar opens95° to facilitate easy part loading/unloading. Clamps may not beexactly as pictured. Clamps may be provided with a new extrudedcylinder with no tie rods and with both ports at the back end.
TC-807
Two versions available. TC-807-Swith solid steel hold-down barand TC-807-U (illustrated) withU-bar. TC-807-S is furnished witha separate bolt retainer whichcan be welded onto the hold-
down bar (bar can be cut or modified). TC-807-U is furnished withflanged washers. A wide range of spindles are available to suityour application. Bar opens 92°.
TC-8021, 8071, 8101
Ideal for dirty environmentssuch as spot and MIG welding.Similar to TC-802, TC-807-Uand TC-810-U, except the inter-nal mechanism is totally
enclosed. Stationary cylinder allows hard piping. Low and narrowmounting profile. U-bar opens 90°. Comes with magnetic ring forsensing switches as a standard feature.
TC-810
Similar to Series 807 but largerand higher capacity. TC-810-Swith solid bar and TC-810-U withU-bar. Bar opens 95°.Accommodates any 3/8-16spindle assembly (not included).
Clamps may not be exactly as pictured. Clamps may be providedwith a new extruded cylinder with no tie rods and with both portsat the back end.
Series TC-846, 847
TC-846 is the pneumatic version of the TC-516. TC-847-S (solidbar) and TC-847-U have patented bar guide feature. Thisprovides additional side support to the hold-down bar and allowsa take-up adjustment to compensate for misalignment or wear.Other features are similar to preceding models. The hold-downbar opens 95°. Accommodates any 1/2-13 spindle assembly (notincluded).
TC-846
TC-847-U
TC-858
Heavy-duty model uses forgedalloy steel links and steel compo-nents machined to closetolerances. Base is a 1/2” thicksteel plate. All pivot points havehardened bushings fitted withhardened steel pivot pins. The 1”
x 1-3/8” steel hold-down bar may be cut, drilled, tapped or weldedto adapt to application. Bar opens 92°.
0139.qxd 2/17/2010 3:11 PM Page 139
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!140
Cla
mp
s an
d W
ork
ho
ldin
gPNEUMATIC HOLD-DOWN CLAMPS
Pneumatic cylinder provides the activating force for these over-center toggle clamps. Built to perform repetitive production operations.Portable and economical for use on short run jobs with temporary fixturing. By adding a sensing switch, the position of the cylinder canbe sensed. All these models come with magnetic ring for sensing capability. See page 147 for sensor options.
See page 147 for pneumatic clamp accessories.
Series TC-817, 827, 868 - Right Angle
Used where space dictates such as rotary indexing tables and injection molding operations. Can also be used with the cylinder horizon-tal in which case the hold-down bar pulls back toward itself. All models can be mounted on the side of the fixture. TC-817-U andTC-817-S can also be top mounted. Clamps may not be exactly as pictured. Clamps may be provided with a new extruded cylinder withno tie rods and with both ports at the back end.
ED
CA
B
TC-827-U TC-868
ECONOMY PNEUMATIC HOLD-DOWN CLAMPSPneumaticHold-Down Clamp
Spindle assemblies are supplied.
C
H B
A
D
ØJ
K
E G
Cat. No. A B C D E G H J KHolding
Cap. Lbs.PortSize
SpindleSize
PriceEach
ETC-17018 3.04 12.75 1.41 0.74 1.25 2.28 2.83 0.28 2.05 375 1/8 NPT 5/16-18 X 2.50 Bonded 92.22ETC-17101 3.69 15.43 1.74 1.25 1.78 4.00 3.74 0.33 2.31 600 1/8 NPT 3/8-16 X 3.50 Bonded 150.20
PneumaticHold-Down Clamp
Spindle assemblies are supplied.
A
E
K
G
ØJ
F
D H
C
L
B
Cat. No. A B C D E F G H J K LHolding
Cap. Lbs.PortSize
SpindleSize
PriceEach
ETC-17171 10.28 7.63 2.80 0.63 1.03 0.63 2.28 2.47 0.25 2.13 0.64 350 1/8 NPT 5/16-18 X 2.50 Bonded 104.42ETC-17271 9.50 9.21 3.93 1.25 1.75 1.25 4.00 3.41 0.33 2.31 0.75 600 1/8 NPT 3/8-16 X 3.50 Bonded 162.58
ExertingForce
80 psi (Lbs.)Cyl.Bore
Cyl. AreaSq. In.
Max. Inlet Press.at Max. MA psig
Max.Hldg.Cap. (Lbs.)
MechanicalAdvantage
PortSize
PriceEachCat. No. A B C D E
TC-817-U 1.125 .994 80 350 2.5:1 to 4.4:1 200/320 7.42 .63 2.44 6.18 2.41 1/8 NPT 139.68TC-817-S 1.125 .994 100 450 2.5:1 to 4.4:1 200/400 7.42 .63 3.06 6.75 2.41 1/8 NPT 139.68TC-827-U 1.500 1.767 95 600 2:1 to 3.5:1 300/500 9.66 .75 3.26 8.75 2.94 1/8 NPT* 232.25TC-827-S 1.500 1.767 110 700 2:1 to 3.5:1 300/500 9.66 .75 3.19 8.64 2.94 1/8 NPT* 232.25TC-868 2.500 4.903 200 4,000 2.3:1 to 4:1 900/1,600 14.32 1.25 4.69 10.11 4.00 1/8 NPT* 502.03*Restrictor fittings are supplied that must be installed on clamp cylinder
0140.qxd 2/23/2010 1:28 PM Page 140
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 141
Clam
ps an
d W
orkh
old
ingPNEUMATIC STRAIGHT-LINE ACTION CLAMPS
Magnetic ring cylinders are used when there is a need to sense the open or closed position of the cylinder. By adding a sensing switch, theposition of the cylinder can be sensed. All these models come with magnetic ring for sensing capability. See page 147 for sensor options.
See page 147 for pneumatic clamp accessories.
LTravel
ThreadE
D P
A
FM
JJ
H hD
G
CylinderArea
(Sq. In.)
Max. Cyl.Air Pressure
psi
MaximumHolding
Cap. (Lbs.)
MaxMechanicalAdvantage
Exert. Forceat 80 psi
(Lbs.)Cylinder
BorePortSize
PriceEachCat. No. P A D E F G H h J L M
TC-816 .75 .44 60 200 5.5:1 190 6.22 1.58 1.28 8-32 .56 .63 .63 — #8 .44 .25 10-32NF 105.35TC-803 1.13 .99 80 600 7.5:1 600 9.82 2.88 2.19 5/16-18 1.09 1.31 1.44 — .19 .75 .44 1/8NPT 154.44TC-830 1.50 1.77 145 2,500 5.7:1 800 14.08 3.25 2.00 3/8-16 1.06 1.63 1.38 1.63 .31 1.25 .63 1/8NPT* 256.64TC-850 2.50 4.90 125 16,000 5.2:1 2,050 21.17 7.50 4.50 5/8-11 2.63 2.25 2.75 — .38 2.00 1.00 1/8NPT* 467.26
*Restrictor fittings supplied that must be installed on clamp cylinder
TC-816 - Miniature
This miniature straight-line clamp is the power version of TC-601.The double-acting cylinder has built in speed controls for smoothoperation. TC-816 is ideal for applications calling for small sizeand remote or automated control. TC-816 uses the TC-810156reed switch.
TC-803 - Compact
This compact plunger action clamp is less than 10” long butprovides a holding capacity of up to 600 lbs. The 7/16” diameterplunger extends 3/4” to a locked position. The end of the plungeris drilled and tapped for a 5/16-18 spindle. Also available as afully enclosed clamp (TC-8031).
TC-830
The 5/8” dia. plunger travels forward 1-1/4” from an open to aclosed and locked position. Plunger is drilled and tapped toaccept a 3/8-16 spindle or to receive your custom fixture. TC-830is also available as special order in an alternate configuration asTC-830-10 which locks in the retracted position only and has aplunger travel of 3/4”. Please call for price and delivery.
TC-850 - Large
The largest of the straight-line actions, this model has a full 1”dia. plunger that extends 2” and goes into a mechanical lock. A3/8” thick steel base provides rigidity and can be welded or boltedinto position. Snap ring construction permits easy removal of theplunger without demounting the entire unit.
TC-8031 - Fully Enclosed
TC-8031 is the fully enclosed version of TC-803. It can be used in the harshest environments. Cylinder is sensor ready and the clampcan be hard piped.
HoldingCapacity
PlungerTravel
PlungerThread
PortSize
PriceEachCat. No. A B C D E F G H J
TC-8031 2,000 Lbs. .75 5/16 - 18 2.37 7.83 .037 2.17 2.36 .44 2.75 1.25 .27 1/8 NPT 404.86
0141.qxd 2/17/2010 3:12 PM Page 141
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!142
Cla
mp
s an
d W
ork
ho
ldin
gPNEUMATIC HEAVY DUTY CLAMPS
See page 147 for pneumatic clamp accessories.
Toggle-LockTC-840, 841
Designed for high production applications, these pneumatic clamps offer exceptional clamping forces and holding capabilities.Does not require greater pressure to open than to close.The TC-840 and TC-841 have oval cylinders which allows them to be used in close quarters or they can be ganged together in multiple installations. The even numbered models feature a 180°clamping arm which travels to an over-center locked position parallel (180°) to the clamps center line. The corresponding odd numbered models have a 90° arm. The angular locked position of both versions is precisely controlled by the hardened steel insert. The magnetic ring cylinders are used when there is a need to sense the open or closed position of the cylinder. Then by adding a tie rod mounted reed switch, the position of the cylinder can be sensed. See page 147 for sensor options.
Note: Maximum inlet pressure: 150 psig.
Max. Exert.Force
@ 80 psig2” from
Pivot Point
Hold Cap.@ 3” fromPivot to
Load Point
MechanicalAdvantage
2” fromPivot Point
Range of Arm
PriceEachCat. No. Bore A B C D E F G H J K L M N O
TC-840 1.5 Equiv. .375 1.375 10 .625 100° 1.812 .28 .875 — 3.69 1.875 2.563 1.000 — 180° 1,500 475 3:1 616.78TC-841 1.5 Equiv. .375 1.375 10 .625 100° 1.812 .28 .875 3.25 — 1.875 2.563 1.000 5.47 90° 1,500 475 3:1 616.78
TC-860, 861, 890, 891,1001A
Designed for high production applications, these pneumaticclamps offer exceptional clamping forces and holding capabilities.Does not require greater pressure to open than to close. Theeven numbered models feature a 180° clamping arm whichtravels to an over-center locked position parallel (180°) to theclamps center line. The corresponding odd numbered modelshave a 90° arm. The angular locked position of both versions isprecisely controlled by the hardened steel insert. The magneticring cylinders are used when there is a need to sense the openor closed position of the cylinder. Then by adding a tie rodmounted reed switch, the position of the cylinder can be sensed.See page 147 for sensor options.
Max. Exert.Force
@ 80 psig2” from
Pivot Point
Hold Cap.@ 3” fromPivot to
Load Point
MechanicalAdvantage
2” fromPivot Point
Range of Arm
PriceEachCat. No. Bore A B C D E F G H J K L M N O
TC-860 2.00 .375 1.75 11.63 .625 96° 2.50 .34 1.130 — 4.50 2.188 2.500 2.313 — 180° 3,000 1,250 5:1 536.37TC-861 2.00 .375 1.75 12.25 .625 110° 2.50 .34 1.130 4.00 — 2.188 2.500 2.313 6.47 90° 3,000 1,250 5:1 536.37TC-890 2.50 .375 2.00 13.00 .690 96° 3.06 .41 1.250 — 5.50 2.500 3.560 2.760 — 180° 5,000 2,600 6.5:1 635.06TC-891 2.50 .375 2.00 13.63 .690 119° 3.06 .41 1.250 5.00 — 2.500 3.560 2.760 8.06 90° 5,000 2,600 6.5:1 635.06TC-1001A 3.25 .500 2.63 17.88 1.000 122° 3.75 .53 1.750 7.00 — 3.500 3.750 3.500 11.31 90° 10,000 6,000 9:1 965.74
Power RollerTC-870, 871
These models use a roller and cam principle to enable clamping work of inconsistent thickness whilestill maintaining a locked condition. Modular units 2-1/8” square can stack together for minimumdistance between clamping points. Four-way mounting surface for full mounting flexibility. Built-in pre-stop eliminates need to bottom out cylinder. Gives extra travel to automatically compensate for wear.Also permits arm to be machined accurately relative to mounting surface. TC-870-2 maximumopening is 112°, cylinder stroke is 2-3/8”. TC-871-2 maximum opening is 126°, cylinder stroke is 2-7/8”. The magnetic ring cylinders are used when there is a need to sense the open or closedposition of the cylinder. By adding a tie rod mounted reed switch, the position of the cylinder can besensed. All these models come with magnetic ring for sensing capability. See page 147 for sensoroptions.
67/8 Max. (871)63/8 Max. (870)
33/8Typ. for Screws (4) Slots
13/4
31/8
TC-871
111/2141/4
TC-870
21/8
25/32
1/4
3/4
9/32
1/4
5/8 3/8
21/8
1
NPT NPT
1/4
TC-870-2 TC-871-2
Max. CylinderAir Pressure
psig
Max. HoldCapacity
(Lbs.)
ExertingForce
80 psig (Lbs.)Cat. No.Cyl.Bore
Cyl. AreaSq. In.
MechanicalAdvantage Price Each
TC-870-2 1.5 1.767 250 psig 2,000 1.2 to 2.5:1 170/350 435.25TC-871-2 1.5 1.767 250 psig 2,000 1.2 to 2.5 170/350 435.25
0142.qxd 2/17/2010 3:12 PM Page 142
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 143
Clam
ps an
d W
orkh
old
ing
PNEUMATIC HEAVY DUTY TOGGLE-LOCK CLAMPSFully Enclosed Side Arm ClampsSeries 863, 864, 893, 894
T
893-L
893-D893-R
C
N
H
B
F
E
S
A
D1
D
JJ1
J
M
R
P
Q
G
118° Arm Opening
Pivot Point
Designed for use in hostile welding and machining environments. Linkage is completely enclosed to keep contaminants out. Clamp armis offset and can be mounted on left side, right side or both sides of the clamp. Over center toggle lock design for maximum reliabilityand clamping forces. Mounting surfaces allow blade mounting on either side of the clamps. Clamp arms are indexable and can berepositioned in 45° increments. Clamp arm is weldable/machinable to suit any application. Magnetic ring sensing options available. Themagnetic ring cylinders are used when there is a need to sense the open or closed position of the cylinder. Then by adding a tie rodmounted reed switch, the position of the cylinder can be sensed. All these models come with magnetic ring for sensing capability. Seepage 147 for sensor options.
863-L
863-R
863-DC
NH
FD
E
A
J
J1
M
R
P
J
J1 Q
G
BPivot Point
130° Arm Opening
U
TC-864-D TC-863-D TC-863, 864 TC-893, 894
Arm Style
Arm Opening
NPTA
PriceEachCat. No. B C D D1 E F G H J J1 M N P Q R S T U
TC-863-D 90 Dual 130 3/8 (2) 2.50 13.58 1.77 - 4.31 1.61 .75 1.00 .37 (2) 3/8-16 (4) 3.64 1.31 3.44 2.24 5 - - 1.77 760.13TC-863-L 90 LH 130 3/8 (2) 2.50 13.58 1.77 - 4.31 1.61 .75 1.00 .37 (2) 3/8-16 (4) 3.64 1.31 3.44 2.24 5 - - 1.77 698.32TC-863-R 90 RH 130 3/8 (2) 2.50 13.58 1.77 - 4.31 1.61 .75 1.00 .37 (2) 3/8-16 (4) 3.64 1.31 3.44 2.24 5 - - 1.77 698.32TC-864-D 180 Dual 121 3/8 (2) 2.50 13.58 1.77 - 4.31 1.61 .75 1.00 .37 (2) 3/8-16 (4) 3.64 1.31 3.44 2.24 5 - - 1.77 760.13TC-864-L 180 LH 121 3/8 (2) 2.50 13.58 1.77 - 4.31 1.61 .75 1.00 .37 (2) 3/8-16 (4) 3.64 1.31 3.44 2.24 5 - - 1.77 698.32TC-864-R 180 RH 121 3/8 (2) 2.50 13.58 1.77 - 4.31 1.61 .75 1.00 .37 (2) 3/8-16 (4) 3.64 1.31 3.44 2.24 5 - - 1.77 698.32TC-893-D 90 Dual 118 3/8 (2) 3.48 14.60 1.38 .69 4.86 3.00 1.00 1.00 .37 (2) 3/8-16 (8) 3.22 1.50 4.12 1.61 5 1.74 1.01 2.50 766.92TC-893-L 90 LH 118 3/8 (2) 3.48 14.60 1.38 .69 4.86 3.00 1.00 1.00 .37 (2) 3/8-16 (8) 3.22 1.50 4.12 1.61 5 1.74 1.01 2.50 690.48TC-893-R 90 RH 118 3/8 (2) 3.48 14.60 1.38 .69 4.86 3.00 1.00 1.00 .37 (2) 3/8-16 (8) 3.22 1.50 4.12 1.61 5 1.74 1.01 2.50 690.48TC-894-D 180 Dual 118 3/8 (2) 3.48 14.60 1.38 .69 4.86 3.00 1.00 1.00 .37 (2) 3/8-16 (8) 3.22 1.50 4.12 1.61 5 1.74 1.01 2.50 766.92TC-894-L 180 LH 118 3/8 (2) 3.48 14.60 1.38 .69 4.86 3.00 1.00 1.00 .37 (2) 3/8-16 (8) 3.22 1.50 4.12 1.61 5 1.74 1.01 2.50 690.48TC-894-R 180 RH 118 3/8 (2) 3.48 14.60 1.38 .69 4.86 3.00 1.00 1.00 .37 (2) 3/8-16 (8) 3.22 1.50 4.12 1.61 5 1.74 1.01 2.50 690.48
Cat. No. Formula to Calculate Exerting ForceTC-863 Max. Clamp Arm = 30 x Line Pressure (psi)TC-864 Exerting Force (lbs.) Distance from Pivot Point to Clamping Point (in.)
Cat. No. Formula to Calculate Exerting ForceTC-893 Max. Clamp Arm = 40 x Line Pressure (psi)TC-894 Exerting Force (lbs.) Distance from Pivot Point to Clamping Point (in.)
Series TC-800, 1200
Operates on an ordinary shop line air (properly filtered and lubricated). Clamp arm completely retracts from the work area for ease inpart loading/unloading. Model 800E and 1200E have extended arm. Min. operating pressure is 70 psig.
Note: Use with pneumatic power only. 3-Way air valve required to power unit (single-acting, spring return).
G F
D
E C
M
B
HN
L
A A1/2
3/16
5/16
P K
J
I
K
J
I
Clamping Arm TC-800, 1200 TC-800E, 1200E
Mtg.Holes
InputPressure
ExertingForce
PriceEachCat. No. A B C D E F G H I J K L M N P
TC-800 1.63 4.81 2.72 .25 2.21 .25 3.13 1.19 .59 .19 .50 1/4 NPT 2.31 1.50 — .26 70-150 850 - 1,500 646.78TC-800-E 1.63 4.81 2.72 .25 2.21 .25 3.13 1.19 .59 .16 .50 1/4 NPT 2.31 1.50 .50 .26 70-150 650 - 1,200 646.78TC-1200 2.25 6.00 3.00 .28 2.44 .28 4.25 1.50 .63 .25 100 1/4 NPT 3.00 1.38 — .26 70-150 750 - 1,600 667.23TC-1200-E 2.25 6.00 3.00 .28 2.44 .28 4.25 1.50 .63 .38 1.00 1/4 NPT 3.00 1.38 .69 .26 70-150 550 - 1,200 667.23
TC-801 - Low Profile
Retracted Extended Clamped
Completely enclosed unit makes it useful in heavy machining applications. Low and narrowprofile for use in confined areas. Clamping arm action extends out horizontally, then clampsdown. The double acting cylinder has built in restriction to help control the speed of thecylinder. Can be adapted with larger cylinder for greater exerting force. The clamp comeswith a magnetic ring cylinder which is used when there is a need to sense the open orclosed position of the cylinder. By adding a sensor the position of the cylinder can besensed. See page 147 and 147 for sensor options.
*Magnetic ring
M
E
DNH J (4 Holes)
BK L
F Gcadb
C
A
PortSize
PriceEachCat. No. A B C D E F G H J K L M N
TC-801 1.62 8.42 1.62 1.50 1.32 5.37 2.84 1.00 #10 5.06 3.36 .50 1.38 1/8 NPT 391.02
Clamping Arm Configurationa b c d
Retracted .50 .13 .38 —Extended .50 .13 1.00 .85Clamped .50 .13 1.00 .65
Exerting Force w/ 1 1/8” Dia. CylinderAir/psig Standard Arm Extended Arm
40 45 lbs. 38 lbs.50 67 lbs. 57 lbs.60 98 lbs. 77 lbs.70 125 lbs. 94 lbs.80 164 lbs. 114 lbs.90 192 lbs. 129 lbs.100 216 lbs. 147 lbs.110 238 lbs. 165 lbs.
PNEUMATIC RETRACTOR CLAMPS
0143.qxd 2/17/2010 3:12 PM Page 143
ALL NEW PRODUCT
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!144
Cla
mp
s an
d W
ork
ho
ldin
g
AUTOMATION POWER CLAMPS
Miniature DesignSeries TC-81L
Opening Angle
Opening Angle
Area of Interference
Pivot
Right Hand: T-slot for sensorLeft Hand: Round slot for sensor
Powered with compressed air max. 6 BarOperation with oil-free air is permissible
B1
B10
L7
L6
81**-101
B10
B7
L9
D3(8x)L1
B18
81L**-141
B11b
B11a
Cat No.Holding Torque
Max (In-lbs.)Clamping Torque
Max (In-lbs.) D3 B1 B7 B10 B11a B11b B18 L1 L6 L7 L9 Price EachHorizontalTC-81L12-10100 221 39 M4X6 24 15 9 27 31.5 28 104 4.5 15 9 331.53TC-81L16-10100 531 53 M5X5 30 20 15 30 39.5 30 119 5.75 20 12 360.55TC-81L20-10100 885 57 M6X8 35 20 20 30.5 40 40 151 9 25 15 419.32TC-81L25-10100 885 159 M6X8 35 20 20 40.5 50 40 151 9 25 15 419.32VerticalTC-81L12-14100 177 39 M4X6 24 15 9 27 31.5 28 104 4.5 15 9 331.53TC-81L16-14100 354 57 M5X5 30 20 15 30 39.5 30 119 5.75 20 12 360.55TC-81L20-14100 708 150 M6X8 35 20 20 30.5 40 40 151 9 25 15 419.32TC-81L25-14100 708 150 M6X8 35 20 20 40.5 50 40 151 9 25 15 419.32
Without Hand LeverSeries TC-82L
L8a
L1 MAXB7a
(L9a)
B23 MAX
L9
B7
Cat No.Max. HoldingTorque (lbs.) B7 B7a B23 L1 L8a L9 Price Each
Without SensorTC-82L2G-2030000 55 25 - 53 179.5 - 18 382.00TC-82L3G-2030000 132 20 3 60 211 42 20 413.70TC-82L4G-2030000 280 25 35 74 242 50 20 429.10With SensorTC-82L2G-203B800 55 25 - 53 179.5 - 18 516.10TC-82L3G-203B800 132 20 3 60 211 42 20 547.80TC-82L4G-203B800 280 25 35 74 242 50 20 563.20
With Hand LeverSeries TC-82L
L1 MAX
L9
B7
B23
Clamping, holding, gripping and positioning of metal sheets andother parts in jigs and handling systems. Features compactdesign, long life cycle, high holding torques, two mounting areas(front and rear), and toggle action mechanism. These modelscan be quickly fitted with magnetic position sensors. Horizontalclamping arms have 120° standard opening angle and the verti-cal clamping arms have 90° standard opening angle. See page147 for sensors.
• Lightweight aluminum design• Enclosed model• Contaminant resistant• Compact design• High holding torques• Long life cycle
• Lightweight aluminum design• Enclosed model• Contaminant resistant• Compact design• High holding torques• Long life cycle
Cat No.Max. Hold.
Torque(Lbs.)Opening
AngleAir
Connection B7 B23 L1 L9PriceEach
Without SensorTC-82L2G-20300H0 55 105° 1/8 25 53 179.5 18 539.70TC-82L3G-20300H0 132 105° 1/8 20 60 211 20 483.20TC-82L4G-20300H0 280 105° 1/4 25 74 242 20 587.80With SensorTC-82L2G-203B8H0 55 105° 1/8 25 53 179.5 18 673.80TC-82L3G-203B8H0 132 105° 1/8 20 60 211 20 617.30TC-82L4G-203B8H0 280 105° 1/4 25 74 242 20 721.90
0144.qxd 2/17/2010 3:12 PM Page 144
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 145
Clam
ps an
d W
orkh
old
ing
PNEUMATIC SWING CYLINDER CLAMPS AND ACCESSORIESSwing and Straight Line Cylinders with Standard Sensing Feature
90° swing of clamping arm minimizes obstruction in the work space and makes loading and unloading of parts easy. Ideal for installa-tions where hydraulic power is not suitable. Straight line clamps operate in only straight line or vertical clamping strokes. These doubleacting clamps are intended for quick clamping in secondary manufacturing operations. Made of aluminum, red anodized, with either athreaded body that permits three mounting options, or a block style mounting body. Available with or without arm. Separate arm optionsavailable. See page 145. TC-8015, 8016, 8115 and 8116 are supplied with a 10-32 hex head steel spindle (TC-305203). TC-8415 and8416 are supplied with a 3/8-16 hex head spindle assembly (TC-485203-AL) and neoprene cap (TC-235110). TC-8215, 8216, 8315 and8316 are supplied with a 3/8-16 hex head aluminum spindle (TC-485203-AL). Standard sensing feature allows user to determine whenthe clamps are fully open and fully closed. To sense the opened and closed positions, optional small low voltage hall effect switches canbe installed in a groove machined into the side of the cylinder body. The switches are actuated by a magnetic piston ring as the cylinderpiston moves up and down. The open or closed condition of the switches is then read by a programmable logic controller (PLC) or otherelectronic device. Optional sensing switches available. See page 147. Swing Cylinder Rotation: Frame of reference for specifyingrotation is the clamp arm viewed from above during the clamping stroke. A right-hand unit rotates clockwise and then clamps down; aleft-hand unit rotates counter-clockwise, and then clamps down. The straight line cylinders offer only vertical clamping strokes. The armsdo not swing. Straight line cylinders supplied without arm and without spindle assembly. See page 147 for sensor options.
See page 147 for pneumatic clamp accessories.
Series TC-8000, 8200, 8400 - Threaded Body with or without Arm
F
EUnclampPort
ClampPort
A
B
C
D Thread
Mounting blocks available for threaded body style. See page 145.Series TC-8200 Series TC-8000, 8400-LA
Exerting Force@
80 psiw/Standard Arm
w/ ArmCat. No.
w/o ArmCat. No.
Rot.Trvl.
VerticalClampStroke
PortSize
Price EachSwing A B C D E F G H w/ Arm w/o Arm
TC-8015 TC-8015-LA RH .466 .38 22 4.88 2.87 .62 11/8-16 1.25 — — — 10-32 264.81 247.28TC-8016 TC-8016-LA LH .466 .38 22 4.88 2.87 .62 11/8-16 1.25 — — — 10-32 264.81 247.28TC-8215 TC-8215-LA RH .75 .50 80 6.36 3.36 .87 21/4-12 3.00 1.16 .25 2.66 1/8 NPT 350.41 315.53TC-8216 TC-8216-LA LH .75 .50 80 6.36 3.36 .87 21/4-12 3.00 1.16 .25 2.66 1/8 NPT 350.41 315.53TC-8415 TC-8415-LA RH .75 .50 62 6.14 3.17 .88 13/4-12 2.13 .98 — — 1/8 NPT 318.77 290.11TC-8416 TC-8416-LA LH .75 .50 62 6.14 3.17 .88 13/4-12 2.13 .98 — — 1/8 NPT 318.77 290.11
Series TC-8100 - Block Style - Standard Sensing Feature - with or without ArmSeries TC-8300
Series TC-8100 Series TC-8300-LA
Vert.ClampStroke
Exerting Force@
80 psiw/Standard Arm
w/ ArmCat. No.
w/o ArmCat. No.
Rot.Trav.
PortSize
Price EachSwing A B C D E F G H J K L M N P Q R w/ Arm w/o Arm
TC-8115 TC-8115-LA RH .466 .38 22 4.88 3.50 1.25 1.25 .62 .47 .47 1.00 1.12 1.00 .25 1.00 1.57 .35 .20 #10 10-32 252.91 235.96TC-8116 TC-8116-LA LH .466 .38 22 4.88 3.50 1.25 1.25 .62 .47 .47 1.00 1.12 1.00 .25 1.00 1.57 .35 .20 #10 10-32 252.91 234.96TC-8315 TC-8315-LA RH .75 .50 80 6.36 4.27 3.00 2.00 1.00 .72 1.22 2.25 .53 2.37 .44 2.25 1.016 .65 .40 .313 1/8 NPT 340.78 303.14TC-8316 TC-8316-LA LH .75 .50 80 6.36 4.27 3.00 2.00 1.00 .72 1.22 2.25 .53 2.37 .44 2.25 1.016 .65 .40 .313 1/8 NPT 340.78 303.14
L-ArmsSeries TC-80152, 82151, 841512
A F
B
E
CD
Use w/Series No.
PriceEachCat. No. A B C D E F
TC-801528 8000, 8100 1.75 1.12 .39 .27 .62 10-32 20.12TC-801529 8000, 8100 2.87 2.25 .39 .27 .62 10-32 20.12TC-821512 8200, 8300 2.75 2.00 .75 .37 .75 3/8-16 24.20TC-821513 8200, 8300 3.75 3.00 .75 .37 .75 3/8-16 31.42TC-841512 8400 2.31 1.58 .75 .37 .75 3/8-16 31.26
T-ArmsSeries TC-80153, 80155
A
FBB
E
C D
Use w/Series No.
PriceEachCat. No. A B C D E F
TC-801530 8000, 8100 2.87 1.12 (2) .39 .27 (2) .62 10-32 (2) 28.39TC-801531 8000, 8100 5.12 2.25 (2) .39 .27 (2) .62 10-32 (2) 28.39TC-821554 8200, 8300, 8400 4.75 2.00 (2) .75 .37 (2) .75 3/8-16 (2) 35.06TC-821555 8200, 8300, 8400 6.75 3.00 (2) .75 .37 (2) .75 3/8-16 (2) 35.06
Blank ArmsTC-801532, 821556
E
FAB
D
G
C
Use w/Series No.
PriceEachCat. No. A B C D E F G
TC-801532 8000, 8100 1.37 1.00 .39 .25 .62 10-32 (2) .62 21.33TC-821556 8200, 8300, 8400 1.50 1.06 .75 .37 .75 1/4-20 (2) .75 37.10
Mounting BlocksTC-801553, 821553, 841550
PriceEachCat. No. A B C D E F
TC-801553 1.38 .69 1.08 .54 .20 11/8-16 35.11TC-841550 2.00 1.00 1.60 .80 .28 13/4-12 36.05TC-821553 2.50 1.25 2.12 1.06 .27 21/4-12 37.43
0145.qxd 2/17/2010 3:13 PM Page 145
ALL NEW PRODUCT
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!146
Cla
mp
s an
d W
ork
ho
ldin
g
PNEUMATIC SWING CLAMPS AND ACCESSORIESSeries TC-9500
J
(CLAMP STROKE)K
N (PORTS)
BA
DE
90°±5°
Clamp ArmsFor Series TC-9500
B B
A
CD
F
D C
A
BF
E
TC-954054
Series TC-89R
l6l5
l3
l1
M3
M3
Rotation Range90° ±5°right
Rotation range 90°±5°(standard adjustment)
h3
Clamp ArmsFor Series TC-89R
b
h h1
l
l1l2
M1
Cat No. I I1 I2 h h1 M1 b Price EachTC-8JG-215-1 67 52 7 15 27.8 M6 15 35.15TC-8JG-217-1 80 60 10 20 35.7 M8 20 38.90TC-8JG-218-1 95 70 10 25 40 M8 25 41.72TC-8JG-219-1 106 80 10 30 48.4 M8 30 47.91TC-8JG-220-1 120 90 12 35 53 M10 35 54.67
Cat No.ClampForce A B D E J K N Price Each
TC-9522R 45 36 25 — — 150.7 13 M5 282.80TC-9522L 45 36 25 — — 150.7 13 M5 282.80TC-9530R 61 44.7 34 12.7 5.1 167.3 20 1/8NPT 315.70TC-9530L 61 44.7 34 12.7 5.1 167.3 20 1/8NPT 315.70TC-9540R 105 52 40 16 9 176.2 20 1/8NPT 338.25TC-9540L 105 52 40 16 9 176.2 20 1/8NPT 338.25
Innovative design allows clamp arm to swing 90° in a horizontalplane at the top of the stroke before traveling down through theclamping stroke. There is no linear travel during rotation. Pistonrod is fully shielded throughout the stroke. Clamps are sensorready built-in sensor tracks. Clamp arms are ordered separately.Clamp forces shown are at 80psi with shortest standard arm. Seepage 147 for sensors.
Standard arms for the TC-9500 series pneumatic swing clampsare made from aluminum and are mounted in 90° increments tothe piston rod.
Swing clamp arms are madefrom aluminum and may bepositioned radially 360°.
• TC-8JG-215-1 used withTC-89R20-010-1
• TC-8JG-217-1 used withTC-89R32-010-1
• TC-8JG-218-1 used withTC-89R40-010-1 andTC-89R40-025-1
• TC-8JG-219-1 used withTC-89R50-025-1
• TC-8JG220-1 used withTC-89R63-025-1
L-Arm
T-Arm
Cat. No.Use With
Series A B C D E F Price EachL-ArmsTC-954050 9540, 9530 70 50 20 10 20 M8X1.25 24.15TC-954053 9540, 9530 100 80 20 10 20 M8X1.25 31.35TC-952250 9522 58 45 15 7.5 15 M6x1.0 22.15TC-952253 9522 78 65 15 7.5 15 M6X1.0 28.30T-ArmsTC-954054 9540, 9530 120 50 20 10 20 M8X1.25 35.04TC-954055 9540, 9530 180 80 20 10 20 M8X1.25 35.04TC-952254 9522 103 45 15 7.5 15 M6X1.0 30.55TC-952255 9522 143 65 15 7.5 15 M6X1.0 30.55
TC-954050
Easily adjustable swing directions, left hand, right hand,straight pull (TC-89R20-010-1 not adjustable). Simple, doubleacting cylinder will produce several million cycles. Clamps aresensor ready built-in sensor tracks for 4mm round diameter or6.5mm x 5mm T-slot style sensors. Clamp arms are orderedseparately. See page 147 for sensors.
Cat No.Total
Stroke
TravelDuring
Rotation
VerticalClampStroke
ExertingForce At
80 psi h3 I1 I3 I5 I6 M3 Price EachTC-89R20-010-1 21 11 10 20 105.5 39.5 22 22 32 M5 227.37TC-89R32-010-1 28 18 10 62 125 60 36 32 45 G1/8 252.63TC-89R40-010-1 31.5 21.5 10 94 140 66 40 40 54.5 G1/8 282.61TC-89R40-025-1 46.5 21.5 25 94 170 66 40 40 54.5 G1/8 294.95TC-89R50-025-1 52 27 25 154 194.5 78.5 50 50 65 G1/8 341.67TC-89R63-025-1 58.5 33.5 25 242 211.5 95 62 62 80 G1/4 401.85
0146.qxd 2/17/2010 3:13 PM Page 146
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 147
Clam
ps an
d W
orkh
old
ing
Switching Logic Normally openOperating Voltage 528 VDCSwitching Current 50 mA Max.
Power Rating1.5 Watts Warning:Never exceed rating (Watt = Voltagex Amperage) or permanent damage to sensor willoccur.
Leakage Current 0.01 mA Max.
CableRobotic grade, abrasion resistant polyurethane(PUR) jacket, PVC insulation
Operating Frequency 1000 Hz
Magnetic Requirement50 Gauss parallel14° to 158° F (-10° to +70°C)
Enclosure Classification IP 67 (NEMA 6)Protection Circuit Reverse polarity, surge suppression
PNEUMATIC CLAMP ACCESSORIESSensing SwitchesSeries TC-8215-SO
These switches are optional and can be used with all series pneumatic swing and straight line cylinders. WARNING: Reverse wiringwill destroy solid state electronic components. Presence of external magnetic/electromagnetic field may interfere with theoperation of the sensor.
TC-8315w/ Sensor
TC-8215-SO-25Sensing Switch
TC-8215-SO-27Sensing Switch
Output CurrentSourcing
VoltageDrop
Current Consumption
LEDIndicator
LeadLgth.
PriceEachCat. No.
TC-8215-SO-25 PNP 1.2V@25mA max. 9 mA@24 VDC max. Green 3 Meters 45.60TC-8215-SO-26 NPN .5V@25mA max. 7 mA@24 VDC max. Red 3 Meters 45.60TC-8215-SO-27 PNP 1.2V@25mA max. 9 mA@24 VDC max. Green 6" w/ Pigtail Connector 47.50TC-8215-SO-28 NPN .5V@25mA max. 7 mA@24 VDC max. Red 6" w/ Pigtail Connector 47.50
Sensing SwitchesNew Style
Tie Rod04mmCat. No. Mount Operation Operating Voltage Switching Current Voltage Drop Cord Type Price EachTC-810165 Tie Rod TRIAC 24-240V AC
50/60Hz Only4 AmpsMax-25
Amplnrush1.5V @.05A Max. 3 meters 64.66
TC-810172 Tie Rod TRIAC 24-240V AC50/60Hz Only
4 AmpsMax-25Amplnrush
1.5V @.05A Max. 6" Male M8 Connector 66.78
TC-810166 Ø4mm PNP 4.5-28V DC 100mA Max. .5V @50mA Max. 3 Meters 48.34TC-810167 Ø4mm NPN 4.5-28V DC 100mA Max. .5V @50mA Max. 3 Meters 48.34TC-810173 Ø4mm PNP 4.5-28V DC 100mA Max. .5V @50mA Max. 6" Male M8 Connector 50.35TC-810174 Ø4mm NPN 4.5-28V DC 100mA Max. .5V @50mA Max. 6" Male M8 Connector 50.35TC-810159 Ø4mm SPST 5-120V DC/AC 50/6 50mA Max. 3.0V Max. 3 Meters 48.34TC-810169 Ø4mm SPST 5-120V DC/AC 50/6 50mA Max. 3.0V Max. 6" Male M8 Connector 50.35
SENSOR OPTIONSSeries TC-81015
Switches are activated by a magnetic ring installed on cylinder piston. As the magnetic ring moves under the switch, it closes thecontacts and sends a signal to a programmable controller or other electronic device. All switches have a 9 foot lead except for theTC-810152 which has a 12 foot lead. Longer leads are available as special order. Please call for price and delivery. Switches comewith tie-rod mounting clamp as standard. Minimum gauge rating required for proper operation, as measured on sensor surfaces, is85 GA.
Note: TC-810156 and TC-810158 use a band to mount the switch to the wall of the cylinder. All other models use tie rod clamp clip.
B
A
C
Switch Mounted on Power Clamp(Power Clamp Not Included)
Switch w/ Mounting Clamp
Switch Dimensionsw/o Mounting Clamp
Cat. No. A B C Type FunctionSwitching
VoltageSwitchingCurrent
SwitchingPower
Max. VoltageDrop
PriceEach
TC-810151 .37 .93 .53 Reed, LED, MOV - w/Tie Rod Clip SPST - Normally Open 5-120V AC/DC50/60 HZ
0.5 Amp. Max.0.005 Amp. Min.
10 3.5 Volts 98.24
TC-810152 .37 .93 .53 Reed, LED, MOV - w/Tie Rod Clip SPST - Normally Open 5-120V AC/DC50/60 HZ
0.5 Amp. Max.0.005 Amp. Min.
10 3.5 Volts 117.81
TC-810154 .37 .93 .53 Reed, LED, MOV - w/Tie Rod Clip SPST -Normally Open 0-120V AC/DC50/60 HZ
0.5 Amp. Max. 10 0 Volts 98.24
TC-810155 .37 .93 .53 Hall Effect, LED Sourcing - w/ Tie Rod Clip Normally Open - PNP Output 6-24V DC 0.5 Amp. Max. 12 1 Volt 108.95TC-810156 .37 .93 .53 Reed, LED, MOV SPST - Normally Open 5-120V AC/DC
50/60 HZ0.5 Amp. Max.
0.005 Amp. Min.10 3.5 Volts 98.24
TC-810157 .37 .93 .53 Hall Effect - with Tie Rod Clip Normally Open - NPN Output 6-24V DC 0.5 Amp. Max. 12 1 Volt 108.95TC-810158 .37 .93 .53 Hall Effect Normally Open - PNP Output 6-24V DC 0.5 Amp. Max. 12 1 Volt 108.95
Heavy Duty Switch
Cable: Robotic Grade, abrasion resistant polyurethane (PUR) jacket, PVC insulationTemperature Range: 14 to 158°F (-10 to +70°C)Switching Logic: Normally Open
SwitchType
SwitchingVoltage
SwitchingCurrent
Switching PowerWatts Max.
VoltageDrop
PriceEachCat. No. A B C Function
TC-810153 .87 1.30 .67 ReedLED, MOV
NormallyOpen
24-240V AC50/60 HZ
4 Amp. Max.50 Amp. In Rush.005 Amp. Min.
100 1 Volt 146.25
0147.qxd 2/22/2010 2:57 PM Page 147
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!148
Cla
mp
s an
d W
ork
ho
ldin
gHYDRAULIC POWER WORKHOLDING
Threaded Body Cylinders
Features:• Stainless steel pistons won’t “mushroom” even when used without grippers• Variety of sizes that support precise fixture designs• Springs are designed to return the cylinder and contact points, not intended to pull mechanisms• SAE fluid ports are common to all models• Operating Pressure - 150 to 5,000 psi
Single-acting (spring return) and double-acting threaded cylinders are extremely versatile and durable. They can be designed into avariety of high production applications including workpiece positioning, holding and ejecting applications where space is at a premium.Double-acting cylinders assure complete powered-retraction for CNC controlled operations (where time is critical) or when using heavyend effectors. Double-acting models are also suited to manufacturing applications, such as production punching. Single-acting cylindersshould be used with small end effectors only and where retraction speed is not critical.
Single ActingCat. No.
Double ActingCat. No.
S/Act.A
D/Act.A B C C1 D D1 E F G K L M P S T
— TBC-DA-2220 — 3.444 2.814 2.494 0.625 1.750-16 1.564 0.437 1.375 SAE#4 1/4-20 0.422 0.39 0.2 0.375 0.500TBC-SA-2220 TBC-DA-2215 4.064 5.184 3.684 3.664 0.625 1.750-16 1.564 0.437 1.375 SAE#4 1/4-20 0.422 0.39 0.2 0.375 0.500TBC-SA-3900 TBC-DA-3900 3.465 3.985 3.195 2.875 0.625 1.875-16 1.73 0.625 1.61 SAE#4 5/16-24 0.53 0.39 0.2 0.500 0.625TBC-SA-3906 TBC-DA-3902 5.005 6.405 4.405 4.085 0.625 1.875-16 1.73 0.625 1.61 SAE#4 5/16/24 0.53 0.39 0.2 0.500 0.625TBC-SA-8800 TBC-DA-8800 3.917 4.62 3.62 3.125 0.69 2.500-16 2.375 1 2.25 SAE#4 1/2-13 0.8 0.55 0.375 0.835 0.625TBC-SA-8805 TBC-DA-8802 5.067 6.62 4.62 4.125 0.69 2.500-16 2.35 1 2.25 SAE#4 1/2-13 0.8 0.55 0.375 0.835 0.625
Single-Acting Threaded Cylinders
Cat. No.Force at 5kpsi. Push
BoreSize Rod Stroke
Effec. AreaPush
Oil Cap.Push Price Each
TBC-SA-2220 2,220 0.75 0.437 0.38 0.442 0.168 160.04TBC-SA-3900 3,900 1 0.625 0.27 0.785 0.212 159.53TBC-SA-3906 3,900 1 0.625 0.6 0.785 0.471 192.35TBC-SA-8800 8,800 1.5 1 0.297 1.767 0.525 206.18TBC-SA-8805 8,800 1.5 1 0.447 1.767 0.789 245.29
Double-Acting Threaded Cylinders
Force at 5k psi. Bore Effective Area Oil CapacityCat. No. Push Pull Size Rod Stroke Push Pull Push Pull Price EachTBC-DA-2220 2,220 1,400 0.75 0.437 0.63 0.442 0.292 0.279 0.184 143.54TBC-DA-2215 2,220 1,400 0.75 0.437 1.5 0.442 0.292 0.663 0.438 160.60TBC-DA-3900 3,900 2,390 1 0.625 0.79 0.785 0.478 0.62 0.378 149.02TBC-DA-3902 3,900 2,390 1 0.625 2 0.785 0.478 1.57 0.956 176.92TBC-DA-8800 8,800 4,900 1.5 1 1 1.767 0.982 1.767 0.982 196.38TBC-DA-8802 8,800 4,900 1.5 1 2 1.767 0.982 3.534 1.964 228.37
Threaded Cylinders
Single-acting with spring return action, these cylinders can be used singly or combined byusing a common manifold. Easily mounted. Can be used in any attitude and requires only asingle inlet port. Threaded cylinders can be directly inserted into a fixture or used with mount-ing blocks. Locknuts, mounting blocks and end caps are available. Call for price and delivery.The 1-5/16” through 2-1/2” diameters are furnished with a radial port as well as axial.
BDA
C
F(HEX SIZE)
E(PORT SIZE)
Lbs. Force@ 3,000
psig
OilDisplaceCu. In.Cat. No. Thread Stroke A B C D
SAEE F
PriceEach
TC-010-210-400 1/2-20 .219 279 1.66 1.41 .15 .16 #2 .44 .024 84.70TC-010-210-501 3/4-16 .313 588 2.25 1.97 .22 .28 #4 .62 .061 92.40TC-010-210-702 1-12 .500 1,326 2.56 2.31 .24 .31 #4 .75 .221 98.18TC-010-211-002 15/16-16 .500 2,355 2.63 2.25 .64 1.25 #4 1.00 .393 118.85TC-010-211-004 15/16-16 1.000 2,355 3.63 3.25 .64 1.25 #4 1.00 .785 137.49TC-010-211-502 17/8-16 .500 5,301 2.94 2.57 1.00 1.75 #4 1.50 .884 156.30TC-010-212-004 21/2-16 1.000 9,423 4.13 3.76 1.50 2.38 #4 2.00 3.142 240.82
0148.qxd 2/17/2010 3:14 PM Page 148
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 149
Clam
ps an
d W
orkh
old
ing
HYDRAULIC POWER WORKHOLDING
Features:• Advanced seals and wipers utilize a special, highly wear-resistant construction for long cycle life
and 5,000 psi operation• Triple track piston rod design for field adjustable swing direction• Hardened and hard chrome plated piston rod for increased strength and wear resistance• Advanced metal treated body for superior wear and corrosion resistance• MRO interchange design• Straight pull capacity 600 lbs. at 5,000 psi max (TBSC-SA-475, TBSC-DA-475, TBSC-DA-475-R)• Straight pull capacity 1,400 lbs. at 5,000 psi max (TBSC-SA-1100, TBSC-SA-1100-R, TBSC-DA-1100, TBSC-DA-1100-R)• Straight pull capacity 3,150 lbs. at 5,000 psi max (TBSC-SA-2400, TBSC-SA-2400-R, TBSC-DA-2400, TBSC-DA-2400-R)
The premium threaded body swing/pull clampsare available in both single-acting and double-acting versions. They incorporate the latesthydraulic swing clamp technology. The top portdesign allows easy access for plumbingconnections. They are available with 90 degreeleft or right hand rotation, or with guidedstraight pull. The breather port on single-actingmodels may be replaced with tubing for remoteventing. The optional arms clamp securely tothe piston rod to reduce fatigue and deflection.Arms may be easily modified or custom armsmay be substituted.
Cat. No.
TotalStroke
AClamping
Stroke CClamp
DUnclamp
E F G H J K L M N P Q R S T UTBSC-SA-475 0.65 0.21 0.59 SAE-2 SAE-2 1.929 2.086 3.07 4.429 0.8 M6x1 0.157 0.393 11/8-16UN 4.96 0.495 1.3 1.55 0.61TBSC-SA-475-R 0.65 0.21 0.59 SAE-2 SAE-2 1.929 2.086 3.07 4.429 0.8 M6x1 0.157 0.393 11/8-16UN 4.96 0.495 1.3 1.55 0.61TBSC-DA-475 0.65 0.32 0.59 SAE-2 SAE-2 1.929 2.086 3.07 4.429 0.8 M6x1 0.157 0.393 11/8-16UN 4.96 0.495 1.3 1.55 0.61TBSC-DA-475-R 0.65 0.32 0.59 SAE-2 SAE-2 1.929 2.086 3.07 4.429 0.8 M6x1 0.157 0.393 11/8-16UN 4.96 0.495 1.3 1.55 0.61TBSC-SA-1100 0.89 0.39 0.6 SAE-4 SAE-4 2.4 2.6 3.58 5.31 0.94 M8x1.25 0.196 0.629 13/8-18UN 5.965 0.40 1.5 1.87 0.75TBSC-SA-1100-R 0.89 0.39 0.6 SAE-4 SAE-4 2.4 2.6 3.58 5.31 0.94 M8x1.25 0.196 0.629 13/8-18UN 5.965 0.40 1.5 1.87 0.75TBSC-DA-1100 0.89 0.39 0.6 SAE-4 SAE-4 2.4 2.6 3.58 5.31 0.94 M8x1.25 0.196 0.629 13/8-18UN 5.965 0.40 1.5 1.87 0.75TBSC-DA-1100-R 0.89 0.39 0.6 SAE-4 SAE-4 2.4 2.6 3.58 5.31 0.94 M8x1.25 0.196 0.629 13/8-18UN 5.965 0.40 1.5 1.87 0.75TBSC-SA-2400 1.12 0.5 0.62 SAE-4 SAE-4 3.18 3.38 4.38 6.8 1.28 M10x1.5 0.196 0.87 17/8-16UN 7.543 0.517 2 2.38 1TBSC-SA-2400-R 1.12 0.5 0.62 SAE-4 SAE-4 3.18 3.38 4.38 6.8 1.28 M10x1.5 0.196 0.87 17/8-16UN 7.543 0.517 2 2.38 1TBSC-DA-2400 1.12 0.5 0.62 SAE-4 SAE-4 3.18 3.38 4.38 6.8 1.28 M10x1.5 0.196 0.87 17/8-16UN 7.543 0.517 2 2.38 1TBSC-DA-2400-R 1.12 0.5 0.62 SAE-4 SAE-4 3.18 3.38 4.38 6.8 1.28 M10x1.5 0.196 0.87 17/8-16UN 7.543 0.517 2 2.38 1
Threaded Body Swing/Pull Clamps
TU
S 50
D Port
25
E Port
L
QJ
HG F
M
CN
P
K
AB
R
TBSC-SA-475 TBSC-SA-2400 TBSC-SA-475-R
Cat. No. Swing Operation ForceEffective Area
ClampSq. InchUnclamp
Oil CapacityClamp
Cu. Inch.Unclamp
Max Oil FlowIn 3/m In Price Each
TBSC-SA-475 LH Single-acting 475 0.12 — 0.08 — 12 311.44TBSC-SA-475-R RH Single-acting 475 0.12 0.24 0.08 0.15 12 311.44TBSC-DA-475 LH Double-acting 475 12 — 0.08 — 12 311.44TBSC-DA-475-R RH Double-acting 475 12 0.24 0.08 0.15 12 311.44TBSC-SA-1100 LH Single-acting 1100 0.28 — 0.25 — 25 337.40TBSC-SA-1100-R RH Single-acting 1100 0.28 0.59 0.25 0.52 25 337.40TBSC-DA-1100 LH Double-acting 1100 0.28 — 0.25 — 25 337.40TBSC-DA-1100-R RH Double-acting 1100 0.28 0.59 0.25 0.52 25 337.40TBSC-SA-2400 LH Single-acting 2400 0.63 — 0.7 — 100 394.12TBSC-SA-2400-R RH Single-acting 2400 0.63 1.23 0.7 1.4 100 394.12TBSC-DA-2400 LH Double-acting 2400 0.63 — 0.7 — 100 412.89TBSC-DA-2400-R RH Double-acting 2400 0.63 1.23 0.7 1.4 100 412.89
Swing/Pull Clamp Arms
Custom built arms of any length must clamp to the swing/pull clamp’s piston rodin a manner similar to the arms or some derating of the clamp will be necessary.IMPORTANT: Any clamp using a modified or custom arm that is longer or heavierthan standard arms must be derated to prevent internal damage.
• Do not exceed the maximum speed and pressure ratings for standard arms.• Do not use meter-out circuitry for controlling double-acting clamp speeds.Cat. No. A B C D G H I J K L M N O P Q T U Price EachHSCA-S-475 1.929 0.709 M6 0.63 0.126 1.139 0.394 0.63 0.236 0.217 0.394 0.394 0.256 0.984 M6 0.236 1.22 34.74HSCA-L-475 3.959 0.709 — 0.63 0.126 1.166 0.394 0.63 0.236 0.217 0.394 0.394 0.256 — M6 — 3.25 49.31HSCA-S-1100 2.598 0.709 M8 0.748 0.126 1.294 0.433 0.748 0.236 0.217 0.63 0.472 0.335 1.575 M6 0.315 1.889 40.89HSCA-L-1100 6.019 0.709 — 0.748 0.126 1.412 0.433 0.748 0.236 0.217 0.63 0.472 0.335 — M6 — 5.31 60.13HSCA-S-2400 3.268 0.866 M10 1 0.126 1.459 0.63 1 0.236 0.217 0.866 0.709 0.413 1.969 M8 0.433 2.402 50.50HSCA-L-2400 7.226 0.866 — 1 0.126 1.696 0.63 1 0.236 0.217 0.866 0.709 0.413 — M8 — 6.36 79.37
Flange Mounting Brackets
Flange mounting brackets allow you to secure your swing/pullclamps in two ways. You may use the set screw and nylon threadprotector ball (supplied) or simply lock the clamp using anoptional jam nut. Swing clamps may also be screwed into athreaded hole and locked in position with a jam nut.
Note: Includes locking set screw and nylon ball to protect clamp threads.
A E
B
CB4X D
A
F
I I I I I I I I I I IIIIIIIIIIIIIIIIIIIIIIIIII
IIII
III I
I II I I
I I I I I I I
Cat. No. A B C D E F Price EachTC-FM475 1.5 1.12 11/8-16 0.219 0.5 10-24 58.21TC-FM1100 1.75 1.34 13/8-18 0.272 0.5 10-24 58.21TC-FM2400 2.25 1.77 17/8-16 0.328 1 1/4-20 55.44
Jam Nuts
Cat. No. A B C D E Price EachTC-JN475 1.75 11/8-16 0.685 0.128 0.256 23.16TC-JN1100 1.88 13/8-18 0.82 0.125 0.25 27.60TC-JN2400 2.5 17/8-16 1.06 0.187 0.374 27.60TC-JN5000 3.38 25/8-20 1.5 0.187 0.374 30.67
0149.qxd 2/17/2010 3:14 PM Page 149
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!150
Cla
mp
s an
d W
ork
ho
ldin
gHYDRAULIC POWER WORKHOLDING
Block Cylinders
Features:• Stainless-steel plunger for long-lasting performance• Variety of strokes to meet specific design needs• SAE oil ports• No special mounting hardware required• Operating Pressure - 150 to 5,000 psi
Double-acting block cylinders are designed for punching,pressing, riveting and bending applications. These blockcylinders require no special mounting hardware and can bedual-position mounted (parallel or perpendicular) to pistontravel on every model.
Double-Acting Block Cylinders
BHC-DA-2220
Force at 5k psi. Bore Effective Area Oil CapacityCat. No. Push Pull Size Rod Stroke Push Pull Push Pull Price EachBHC-DA-2220 2,220 1,400 0.75 0.437 0.63 0.442 0.292 0.279 0.184 209.21BHC-DA-2215 2,220 1,400 0.75 0.437 1.5 0.442 0.292 0.663 0.438 230.88BHC-DA-3900 3,900 2,390 1 0.625 0.79 0.785 0.478 0.62 0.378 247.26BHC-DA-3902 3,900 2,390 1 0.625 2 0.785 0.478 1.57 0.956 272.29BHC-DA-8800 8,800 4,900 1.5 1 1 1.767 0.982 1.767 0.982 291.50BHC-DA-8802 8,800 4,900 1.5 1 2 1.767 0.982 3.534 1.964 346.18
Hollow Cylinders
These hollow cylinders can be used to push or pull depending on the position of the ram. They will actuate a rod of any length or shapeand are extremely effective in translating power to a remote location. Larger piston diameter provides greater clamping force. Hardenedsteel piston and rod. Supplied with through hole insert threaded into the top. Optional thread inserts (inch/metric) are available asspecial order. An accessory adapter plate,which fastens to the ram base and permits mounting the ram with a single cap screw is alsoavailable as special order. Please call for price and delivery. Maximum input pressure is 3,500 psig.
B
A
C
Oil DisplacementCu. In.
Lbs. Force @3000 psig
PriceEachCat. No. ID* Port A B C Stroke
TC-021-011-011 .38 1/8 NPT 2.13 1.88 2.25 .375 .547 4,380 173.57TC-020-011-011 .38 #2 SAE 2.13 1.88 2.25 .375 .547 4.380 214.77TC-020-012-021 .50 #4 SAE 3.00 2.63 2.88 .500 1.35 8,100 260.02TC-020-013-031 .63 #4 SAE 3.25 3.00 3.63 .625 2.51 12,066 310.73*Clearance for rod or bolt
O
H
J
TLK
S
CB
A
DE
RK
MP
(S/S Vent Plug) G KV
F
G V
I
Double ActingCat. No.
S/Act.A
D/Act.A B C D E F G H I J K L M O P R S T V
BHC-DA-2220 — 3.078 2.448 2.128 2.36 0.375 0.437 SAE#4 0 0.756 1.206 0.295 1.77 0.98 1/4-20UNC 1.57 0.785 0.9 1.18 0.28BHC-DA-2215 3.698 4.818 3.318 2.998 2.36 0.375 0.437 SAE#4 2.058 0.756 1.248 0.295 1.77 0.98 1/4-20UNC 1.57 0.785 1.77 1.18 0.28BHC-DA-3900 3.031 3.551 2.761 2.441 2.559 0.5 0.625 SAE#4 0 0.788 1.378 0.295 1.969 1.181 5/16-24UNF 1.772 0.886 1.181 1.28 0.35BHC-DA-3902 4.571 5.971 3.971 3.651 2.559 0.5 0.625 SAE#4 2.558 0.788 1.378 0.295 1.969 1.181 5/16-24UNF 1.772 0.886 2.391 1.28 0.35BHC-DA-8800 3.472 4.175 3.175 2.68 3.15 0.835 1 SAE#4 0 0.708 1.42 0.374 2.403 1.548 1/2-13UNC 2.295 1.148 1.5 1.575 0.391BHC-DA-8802 4.622 6.175 4.175 3.68 3.15 0.835 1 SAE#4 2.62 0.708 1.44 0.374 2.403 1.548 1/2-13UNC 2.295 1.148 2.5 1.575 0.391
0150.qxd 2/17/2010 3:14 PM Page 150
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 151
Clam
ps an
d W
orkh
old
ing
HYDRAULIC POWER WORKHOLDINGHydraulic Edge Clamp
For quick part load/unload in drilling, milling, planing, grinding andother surfacing operations on either CNC or Bridgeport-typemachines. Clamps are low profile and provide horizontal andvertical clamping force simultaneously against the sides of aworkpiece allowing cutter access to an entire top surface.Powered using shop air with an air/hydraulic booster. Positivespring return and replaceable grippers.
1.191.25
1.50
.27 (4) Holes .13 Clamping Range & Part Location
1/4-28 Tap-Removable
Standard Gripper
.50 Travel (Max.).19 Optimum
Clamping Range1/8 NPT
2.00
1.381.75
1.00
5.06 .88
Hydraulic Pressure Rangepsig
Vertical Travel @Horizontal
StrokeDisplacement
(In.3)Effective Area
(In.2)Horizontal
StrokePriceEachCat. No. Max Min
TC-70626 3,500 500 .139 .442 .31 .22 467.06
Hydraulic Clamp Force at 5/16" Hydraulic Clamp Force at 5/16"Pressure Horizontal Stroke (lbs.) Pressure Horizontal Stroke (lbs.)
psig Horizontal Vertical psig Horizontal Vertical500 190 170 2500 1060 8701000 390 350 3000 1300 10501500 620 520 3500 1520 12202000 850 700
Semi Automatic - Air / Hydraulic Boosters
Converts normal shop line air pressure to high pressure hydraulic power. With the system filled, the volume of oil required to actuate acylinder or pressure point is only equal to the cubic content of the piston displacement. Boosters have built in manifold and are made ofcorrosion and wear-resistant materials. Hydraulic piston tube has wear rings and the air piston is self centering for long life. Boostersoffer automatic relief of system overcharge as well as complete automatic bleeding with each return, eliminating prefilling. Large volumevisible oil reservoir automatically replenishes the system with available reserves. 100 psig max. input air pressure.
A
B
Nom. Displac.Per Stroke
Cu. In.
ReservoirCapacity
Cu. In.Pressure
RatioNPTPorts
PriceEachCat. No. A B
TC-70101 33.87 1 10.4 1/8 4.5 10.875 753.51TC-70104 32.41 4 42 1/4 6.5 16.375 1034.09
0151.qxd 2/17/2010 3:14 PM Page 151
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!152
Cla
mp
s an
d W
ork
ho
ldin
gHYDRAULIC POWER WORKHOLDING
Swing Cylinders w/o ArmsLight Duty
Unclamp Port(S/A Vent Plug)
K
K
G Clamp Port
M
N
L
I
A
ClampedPosition
D
C
B
J
H
F
E
ArmNot
Included
AB
EF
H
R
J
C
D
I
BoltsIncluded
Arm NotIncluded
N
ML
K
P
QGUnclampPort(S/A VentPlug)
ManifoldPort (FixtureHole Dia. .19)
G ClampPort
Manifold Port(Fixture HoleDia. .19)
I
AB
E
F
JC
D
R
H
Bolts Included
Arm NotIncluded
L M
P N
Q
ManifoldPorts(FixtureHole Dia..19)
GUnclampPort(S/A Vent Plug)
G ClampPort
K
These swing cylinders rotate 90° as they begin their stroke, continuing without rotation for the final clamping stroke. Cylinders can bechanged to left swing, right swing or pull applications by loosening the bottom plug. All single acting cylinders come with a retract springfor single-acting operations. Max. psi 5,000. Clamp arms not included but sold separately on page 155. Body styles available arethreaded with upper flange or non-threaded with lower or upper flange.
*All threaded bodies have upper flange
L
M
K
I
A
D
N
C
B
J
H
F
E
GClamp
Port
ArmNot
Included
GUnclamp Port
Upper Flange
Threaded VE-72VE-600-1, 605-1, 610-1
Lower Flange
VE-70, 73, 75 VE- 71, 74, 76
CylinderCapacity
w/Std. Arm
Hydraulic Oil Capacity
(In.3)BodyStyle
Stroke Effective Area (In.2)
PriceEachCat. No. Enerpac Total Clamping A B C D E F G H I J K L M N
Double ActingVE-70 SURD-51 Upper Flange 1,250 .89 .39 .28 .28 5.31 4.42 2.60 .98 1.82 1.08 SAE #4 .39 1.57 13/8-18 25° 1.12 .75 1.50 430.00VE-71 SLRD51 Lower Flange 1,250 .89 .39 .28 .28 5.31 4.42 2.60 .98 1.82 1.08 SAE #4 .39 1.57 13/8-18 25° 1.12 .75 1.50 398.00VE-72 STRD121 Threaded* 2,600 1.12 .50 .63 .70 6.75 5.63 3.38 1.00 2.25 1.06 SAE #4 .38 2.00 17/8-16 .81 1.38 1.00 2.00 398.00VE-73 SURD-121 Upper Flange 2,600 1.12 .50 .63 .70 6.75 5.63 3.38 1.00 2.25 1.06 SAE #4 .38 2.00 17/8-16 25° 1.38 1.00 2.00 491.00VE-74 SLRD121 Lower Flange 2,600 1.12 .50 .63 .70 6.75 5.63 3.38 1.00 2.25 1.06 SAE #4 .38 2.00 17/8-16 25° 1.38 1.00 2.00 469.00Single ActingVE-600-1 STRS21 Threaded* 475 .65 .32 .12 .08 4.41 3.76 2.09 .98 1.67 1.04 SAE #2 .39 .97 11/8-16 25° .94 .61 1.30 301.00VE-605-1 STRS51 Threaded* 1,100 .89 .39 .28 .28 5.31 4.42 2.60 .98 1.82 1.08 SAE #4 .39 1.57 13/8-18 25° 1.12 .75 1.50 325.00VE-75 SURS-51 Upper Flange 1,100 .89 .39 .28 .28 5.31 4.42 2.60 .98 1.82 1.08 SAE #4 .39 1.57 13/8-18 25° 1.12 .75 1.50 430.00VE-76 SLRS51 Lower Flange 1,100 .89 .39 .28 .28 5.31 4.42 2.60 .98 1.82 1.08 SAE #4 .39 1.57 13/8-18 25° 1.12 .75 1.50 398.00VE-610-1 STRS121 Threaded* 2,400 1.12 .50 .63 .70 6.75 5.63 3.38 1.00 2.25 1.06 SAE #4 .38 2.00 17/8-16 25° 1.38 1.00 2.00 398.00
Swing Cylinders With Arms P
ON
Q D
JR
S
G
FB
A
C
H
M
E
TLK
X
W
F
I
These swing cylinders rotate 90° as they begin their stroke, continuing without rotation for the final clamping stroke. Cylinders can bechanged to left swing, right swing, or pull applications by loosening the side plug and then rotating the plunger to a desired position.The VE-354 and VE-352 have a retract spring for single-acting operations. The VE-360 is only for double-acting operation and has noreturn spring. Clamp arm provided. Can be mounted with the built-in flange by securing the swinger to the top or bottom of a toolingplate or by screwing the threaded body into a mounting bracket.
P
ON
QD
JR
S
G
FB
AC
H
M
E
TLK
X
W
VE-354VE-352, 360
Cat. No. Enerpac A B C D E F G H I J K L M N O P Q R S T W X Price EachVE-354 SC-1 7.37 8.88 5.74 3.00 2.87 1/4-18 1/8-27 3.31 .50 .38-16 .44 .88 17/8-16 1.88 1.28 2.90 2.06 2.00 .40 5.87 1/2-13 1.000 687.00VE-352 SC-3 4.26 5.27 3.48 2.13 2.03 1/8-27 1/8-27 2.15 — .250-20 .32 .63 1-12 1.13 .75 2.00 1.50 1.00 .20 3.71 5/16-24 .500 478.00VE-360 SC-4 3.13 4.30 2.50 1.62 1.40 5/16-27 5/16-27 1.44 — 10-32 .30 .60 3/4-16 .88 .60 1.52 1.13 .75 .20 2.83 5/16-24 .375 507.00*Standard clamping arm supplied. Longer arms indicated in chart can be fabricated by the user.
Cylinder Oil Max.Cylinder Capacity
@ Maxpsi (Lbs.)
Effective Capacity Max.Pressure
PSIArm
SwingCylinder
TypeHydraulic Stroke Retracted
HeightArea (In2) (In.3) Arm
Lgth.Cat. No. Enerpac Total Clamping Pull Push Pull Push
VE-354 SC-1 Straight, Leftor Right
Single or Double-acting,
Pull
2,640 2,164 1,960 1,740 1,200 840
1.50 1.50 1.50 1.50 1.50 1.50
.50
.50
.50
.50
.50
.50
7.37 7.37 7.37 7.37 7.37 7.37
.980
.980
.980
.980
.980
.980
1.767 1.767 1.767 1.767 1.767 1.767
1.470 1.470 1.470 1.470 1.470 1.470
2.650 2.650 2.6502.650 2.6502.650
None 2.00* 3.004.00 5.006.00
3,0003,0003,0003,0002,4002,000
VE-352 SC-3 Straight, Leftor Right
Single or Double-acting,
Pull
700500250
.75
.75
.75
.25
.25
.25
4.52 4.52 4.52
.245
.245
.245
.442
.442
.442
.184
.184
.184
.331
.331
.331
None 1.00* 2.00
3,0003,0002,000
VE-360 SC-4 Straight, Left or Right
Double-acting 300 25
.56
.56.19 .19
3.74 3.74
.137
.137.246 .246
.770
.770.138 .138
.75* 1.50
3,0001,500
0152.qxd 2/22/2010 11:10 AM Page 152
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 153
Clam
ps an
d W
orkh
old
ing
HYDRAULIC POWER WORKHOLDINGSingle-Acting Manifold Cylinder
C
AB
EF
HD
G
These threaded miniature cylinders were designed specifically for tooling. All cylinders are single-acting with spring return action forrapid work release. They have threaded bodies for all types of mountings. Cylinders may be inserted directly in a fixture or used withstandard brackets. Stainless steel construction. Maximum operating pressure 5,000 psi. See page 155 for accessories.
BA
C
G DFEH
VE-411, 412, 414 VE-413 thru 419, 82 thru 86 and 424, 425
Max.Clamp Force
Eff. Area(In.2).
Oil Cap.(In.3).Cat. No. Enerpac Stroke A B C D E F G H Price Each
VE-411 TS-271ST 380 .28 .08 .02 1.58 1.86 .97 .69 .19 6-32 7/16-20 1/2-20 75.00VE-412 TS-2131ST 380 .51 .08 .04 1.99 2.50 1.38 .69 .19 6-32 7/16-20 1/2-20 95.00VE-414 TS-3131ST 560 .51 .11 .06 2.15 2.66 1.52 .75 .19 6-32 7/16-20 5/8-18 97.00VE-413* TS-471ST 980 .28 .20 .05 1.87 2.15 1.71 .65 .27 8-32 7/16-20 3/4-16 80.00VE-416 TS-4131ST 980 .51 .20 .10 2.21 2.72 2.05 .65 .27 8-32 7/16-20 3/4-16 83.97VE-417 TS-4191ST 980 .75 .20 .15 2.62 3.37 2.46 .65 .27 8-32 7/16-20 3/4-16 91.00VE-418 TS-4251ST 980 .98 .20 .19 2.97 3.96 2.82 .65 .27 8-32 7/16-20 3/4-16 81.00VE-419 TS-4381ST 980 1.50 .20 .29 4.27 5.77 4.11 .65 .27 8-32 7/16-20 3/4-16 81.00VE-82 TS-971ST 1950 .28 .39 .11 2.25 2.53 2.03 .81 .39 1/4-28 7/16-20 1-12 83.00VE-83 TS-9131ST 1950 .51 .39 .20 2.50 3.01 2.28 .81 .39 1/4-28 7/16-20 1-12 110.00VE-84 TS-9191ST 1950 .75 .39 .29 3.11 3.86 2.89 .81 .39 1/4-28 7/16-20 1-12 92.00VE-85 TS-9251ST 1950 1.00 .39 .39 3.41 4.41 3.19 .81 .39 1/4-28 7/16-20 1-12 108.00VE-86 TS-9381ST 1950 1.50 .39 .59 4.11 5.61 3.89 .81 .39 1/4-28 7/16-20 1-12 125.00VE-424 TS-18131ST 3860 .51 .77 .40 2.76 3.27 2.50 1.22 .63 5/16-24 7/16-20 15/16-16 125.00VE-425 TS-18251ST 3860 .98 .77 .77 3.52 4.51 3.27 1.22 .63 5/16-24 7/16-20 15/16-16 140.00
*Nitro carburized
Threaded Cylinders
Cylinders can be fixtured into manual strapor bridge clamp assemblies. Fully threadedbodies allow cylinders to be threadeddirectly into tapped holes of the fixture foreasy installation. Available as single-actingspring return or double acting hydraulicreturn. The VE-90 can use carbide grippers(Grippers sold on page 170).VE-88 VE-90
Cylinder Capacity Cylinder Oil@ Max. psi Effective Capacity
(Lbs.) HydraulicStroke
Retr.Hgt.
BoreDia.
Area (In.3) Area (In.2) PriceEachCat. No. Enerpac Push Pull Push Pull Push Pull A B C D E F G H I J K L M
Single-ActingVE-88 WRT-21 3900 — .50 3.25 1.00 .79 — .39 — 3.25 3.75 2.33 1.23 .75 1/4-28 x .32 5/16-24 .62 .24 .30 .50 .25 13/8-18 180.00Double-ActingVE-90 WMT-39 3900 2700 .50 3.26 1.00 .79 .54 .39 .27 3.26 3.76 2.05 1.30 .56 1/4-28 x .39 1/8-27 NPT .73 — .27 — — 13/8-18 273.00
Hollow Cylinders
I
K 1/8-27 ManifoldPNT and NTP(except VE-347)
DJL
C
EF
H
A B
1/8-27 NPTThese hollow cylinders combine compactness with power andversatility. Any application requiring either a pushing or pullingaction is easily handled with this type of cylinder. The cylindersare threaded and can be placed over a bolt or a stud to upgrademost existing manual clamping fixtures.
VE-326, 327,355
VE-347, 349,350, 351
Eff. Area(In.2)
ClampPres.*
Oil Cap(In.3)
PriceEachCat. No. Enerpac A B C D E F H I J K L
VE-326 RWH-120 2.19 2.50 1.19 2.75 1.38 3/4-16 .39 5/16-18 .19 .770 23/4-16 2.76 27,600 .86 419.00VE-327 RWH-121 3.19 4.19 1.19 2.75 1.38 3/4-16 .53 5/16-18 .19 .770 23/4-16 2.76 27,600 2.76 551.00VE-355 RWH-20 2.06 2.38 1.50 1.79 1.00 .53 .28 1/4-20 .12 1/2-20 17/8-16 1.32 4,000 .41 245.00VE-347 CY1254-25 2.00 2.25 .91 1.75 .56 3/8-16 .29 1/4-20 1.75 .390 .86 .87 2,610 .22 260.00VE-350 CY2129-25 2.00 2.31 .75 2.63 1.13 3/4-10 .31 3/8-16 2.50 .765 .86 2.47 7,410 .77 301.00VE-349 CY2129-5 2.73 3.36 1.48 2.63 1.13 3/4-10 .31 3/8-16 2.50 .765 1.06 2.47 7,410 1.56 366.00VE-351 CY2754-5 3.00 3.63 1.55 3.50 1.25 7/8-9 .31 3/8-16 3.13 .890 1.50 4.44 13,320 2.80 443.00*Clamping pressure at 10,000 psi, except for VE-355 which is 3,000 psi
Clamping CylindersSingle-Acting
Used for a wide range of production tooling applications, heavy duty force requirements and high cycle applications. Block shapedclamps provide a high amount of force in a tight area. Designed to be surface mounted on the machine tool bed or on a fixture surface.Provide force in horizontal or vertical direction. Cylindrical clamps have collar threads and base holes for mounting. All have springreturn operation for easy unloading of workpiece and faster cycling. Spring is designed to return plunger only.
VE-372VE-373,377,378 VE-375
Cyl. Cap.@ Max
psi
Cyl. Eff.Area(In.2)
OilCap.(In.3)
Hyd.Stroke
Retrac.Hght.
BoreDia.
PriceEachCat. No. Enerpac A B C D E F G H I J K L M
VE-372 RW-50 9,940* .62 1.62 1.12 .994 .620 1.62 2.25 1.50 1.62 1.12 .22 3/8-18 1.00 .56 1.12 2.31 .75 — 209.00VE-373 RW-51 9,940* 1.00 4.12 1.12 .994 .994 4.37 5.37 4.12 11/2-16 1.00 1/4-20 3/8-18 .75 .12 1.12 — — 3/4-16 230.00VE-377 RW-53 9,940* 3.00 6.25 1.12 .994 3.20 6.50 9.50 6.25 11/2-16 1.00 1/4-20 3/8-18 .75 .12 1.12 — — 3/4-16 236.00VE-378 RW-55 9,940* 5.00 8.25 1.12 .994 5.20 8.50 13.50 8.25 11/2-16 1.00 1/4-20 3/8-18 .75 .12 1.12 — — 3/4-16 250.00VE-375 RW-102 22,300* 2.00 4.53 1.69 2.236 4.75 4.78 6.78 4.53 21/4-14 1.38 5/16-18 3/8-18 .75 .19 1.06 — — 1-8 274.00*Cylinder capacity shown is rated at 10,000 psi
0153.qxd 2/17/2010 3:15 PM Page 153
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!154
Cla
mp
s an
d W
ork
ho
ldin
gWORK SUPPORTS
Work supports provide additional support to avoid excessive movement or deflection of the workpiece during machining. Whenhydraulic pressure is applied to the work support, a piston pushes against an internal adjustable spring that advances the work supportplunger against a workpiece at the force set by the adjustable spring. As more hydraulic pressure is applied, an internal sleeve will gripand lock the plunger in that position. Available as a spring or fluid advance unit. The spring advanced unit can be converted to air bysimply removing the internal adjustment spring and attaching a low pressure air line to the air breather vent tube. Operating pressure is700 psi minimum, 5,000 psi maximum.
Q
T
SRF
L
E
K
CONTACT BOLTINCLUDEDJ
BA C
H
SAE #4U
J1J1
.28
MI
AIR BREATHER/FILTER VENT1 8-27 NPT
N
D
AIR PORT
OPTIONAL MANIFOLD-MOUNT PORT(FIXTURE HOLE ¯.0.17)
U
Cap@ Max
psi
Support Plunger OilCap.(In.3)
Hyd.Stroke
Spring Force Lbs. PriceEachCat. No. Enerpac Extended Retracted A B C D E F H I J J1 K L M N Q R S T U
Fluid AdvancedVE-19 WFL-111 2,500 .38 3.4 5.2 .06 3.53 3.91 3.10 13/8-18 .63 .49 .56 1.08 .18 .57 M10x1.5 1.50 .70 .73 .28 1.62 2.38 .94 .17 240.00Spring AdvancedVE-21 WSL-111 2,500 .38 3.4 5.2 .02 2.97 3.35 2.54 13/8-18 .63 .49 .44 .94 .18 .57 M10x1.5 1.50 .30 .73 .28 1.62 2.38 .94 .17 207.00
Turbo Air/Hydraulic Pumps
A turbo air pump is recommended where input air pressure is limited. Engineered to recycle exhaust air to help power the pump.Maintains a tight pressure range for reliable clamping performance. Pump will automatically restart in the event of a pressure drop inthe hydraulic system. Mounting plate allows for horizontal or vertical machine-side mounting. Buna-N polyurethane and Teflon seals.
VE-391, VE-392Requires remote valve to complete system. Best
choice for multiple remote valve applications.
VE-4604 way tandem center valve can operatesingle to double-acting cylinders. Best
choice for continuous hookup to cylinder.
Hydraulic PressureAIr
Consump.SCFM
AIrPressureRange psi
Usable OilRange psi Hydraulic
Air RatioHydraulic
Output Ports.Capacity (In.3) Price
EachCat. No. Enerpac Min. Max. Vertical HorizontalVE-391 PACG-5002SB 2,500 5,000 72:1 SAE #4 15 40-120 70 127 646.00VE-392 PACG-3002SB 1,400 5,000 50:1 SAE #4 15 40-120 70 127 712.00VE-460 PAMG-5402NB 2,500 5,000 72:1 3/8-18 15 40-120 70 127 1051.00
0154.qxd 2/17/2010 3:15 PM Page 154
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 155
Clam
ps an
d W
orkh
old
ing
HYDRAULIC POWER WORKHOLDING
Clamping Arms
CA
B
G
E
D
KL
FH
I O
MJ
N
P
These clamp arms are designed for use with the swing cylinders shown on page 152. Clamp arms can be positioned and tight-ened without removing the swing cylinder from the fixture. Clamp arm design eliminates the use of a vise when securing to a plunger.Short arms have a tapped hole for buttons and toggle pads. Long arms can be shortened to desired length.
ABC
DE
G
Q
O
K
F
L
H
IP
JM
N
Short Arm Long Arm
For Use WithCylinder Cap.Cat. No. Enerpac A B C D E F G H I J K L M N O P Q Price
Short ArmVE-600-2 CAS-21 500 1.60 .97 .38 .76 .38 .13 .25-28 .68 .466 .394 .63 .28 .37 .40 .25-20 14° .50 41.00VE-605-2 CAS-51 1,250 2.39 1.57 .50 1.00 .50 .17 .312-24 1.02 .728 .630 .75 .31 .51 .45 .312-18 12° .63 44.00VE-610-2 CAS-121 2,600 3.13 2.00 .70 1.39 .69 .28 .375-24 1.40 1.000 .875 1.19 .44 .66 .63 .375-16 18° .82 53.00Long ArmVE-14 CAL-22 500 3.63 .44 .38 .76 .38 .13 M6x1 .68 .466 .394 .63 .28 .37 .40 .92 14° — 52.00VE-15 CAL-52 1,250 5.81 .55 .50 1.00 .50 .17 M8x1 1.02 .728 .630 .75 .31 .51 .45 1.37 12° — 63.00VE-16 CAL-122 2,600 7.06 .72 .70 1.39 .69 .28 M10x1.5 1.40 1.000 .875 1.19 .44 .66 .63 1.73 18° — 83.00VE-17 CAL-202 3,900 7.95 1.00 .95 1.90 .95 .20 M12x1.25 2.59 1.400 1.259 1.18 .47 .94 .82 1.11 18° — 97.00
Jam Nuts
C
A
BD
E
Cat. No. Enerpac A B C D E Price EachVE-387 JN-48 1.88 15/16-16 .25 .25 .12 30.50VE-307 JN-12 2.50 17/8-16 .50 .38 .19 34.00
Sequence Valves For Time Interval Control
These valves can be plumbed to provide a sequence of clampingfunctions from just one hydraulic power source. Sequenced locat-ing, clamping, and/or supporting functions can be controlled in alogical order by plumbing one sequence valve to each clampinggroup requiring a different time interval. The valve can be presetto different pressure values, allowing fluid flow in sequence as thehydraulic pressure increases in the entire system to whatever thepower source provides, after all valves are open. These valvesare basically timers, not pressure controllers. The VE-211features a lock nut which secures the hydraulic pressure settingfor the secondary circuit and a tamper proof cover can be placedover the set screw. Maximum operating pressure is 5,000 psi.
VE-211
VE-210
Cat. No. Enerpac Pressure Setting Range (psi) Price EachVE-210 V-2000 200 to 2,000 319.00VE-211 WVP-5 500 to 5,000 406.00
Hydraulic Oil
Cat. No. Enerpac Description Price EachVE-255 HF-101 Hydraulic Oil (gallon) 42.50
0155.qxd 3/2/2010 2:36 PM Page 155
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!156
Cla
mp
s an
d W
ork
ho
ldin
gCLAMPING SYSTEMS
Fixture Clamps
The Mitee-Bite™ clamping system combines strength, versatilityand performance with economy and ease of use. Consisting of acam action socket cap screw with a brass hex washer, set upsare simplified even for hard to hold parts. Its small size allowsmore parts per load on multiple series jobs. The low profile makesprogramming easier because there are no clamps to jump over.Fast to use (just 1/4 turn of screw loosens clamp) and no looseparts to set up each time. Economical— all six sides of the hexnut can be used. Available in six sizes for use on multiple partfixtures. Metric sizes are in millimeters. MB-10203 and MB-50207are stainless steel.
PRODUCTS INC.
Discount 143 applies.
Cat. No.ScrewSize
ThreadLgth.
HexSize
HexHt.
Max.Holding
Force Lbs.Total
Throw
No. ofClampsPer Pkg.
PricePer Pkg.
1-24InchMB-2 8-32 .350 .312 .110 205 .030 10 50.70MB-3 10-32 .340 .500 .160 350 .040 10 53.35MB-4 1/4-20 .470 .625 .190 800 .040 10 53.35MB-10203* 1/4-20 .470 .625 .190 — .040 4 57.45MB-5 5/16-24 .460 .812 .190 750 .040 12 66.85MB-5C 5/16-18 .460 .812 .190 750 .040 12 66.85MB-6 3/8-16 .710 .812 .250 2,000 .050 10 61.50MB-8 1/2-13 .900 1.000 .375 4,000 .100 8 66.85MetricMB-50204 M4 9.6 7.93 2.80 93 .76 10 50.70MB-50206 M6 11.2 15.86 4.75 364 1.01 10 53.35MB-50208 M8 15.0 20.61 4.75 340 1.01 12 66.85MB-50207* M8 15.0 20.60 6.35 — 1.01 4 76.95MB-50210 M10 19.0 20.61 6.35 910 1.52 10 61.50MB-50212 M12 22.8 25.38 9.52 1,818 2.03 8 66.85MB-50216 M16 28.5 30.13 12.69 2,720 2.54 4 50.70*Stainless steel
Multi-Fixture Clamps and Stops
Works in plates with tapped hole layouts or T-slot configurationsproviding flexible set ups for hard to hold parts. Can be mountedvertically or horizontally. Stops locate workpiece for repeatpositioning. Tapered mounting slots prevents movement whenclamping pressure is applied. Closed slot.
PRODUCTS INC.
Discount 143 applies.
Clamp Stop
MountingPriceEach
Cat. No. Description A B C F G Screws 1-24MB-150 Clamp 3.75 1.12 .62 1.68 .50 1/2 54.55MB-200 Stop 3.75 1.12 .87 1.68 .50 1/2 49.40
Uniforce® Clamps
Compact and economical, uniforce clamps enable you to fixturemore parts on the machine table. The specially designed steelwedge spreads the clamping force uniformly on both sides of thealuminum channel. Minimizes tool changes. Ideal for clamping flator round work pieces. Order one piece and you will receive onepackage.
PRODUCTS INC.
Discount 143 applies.
A
C
D
E
BF
Machinable Uniforce Clamps
The compact clamp is available with extra material on the clamp-ing jaws so it can be machined to conform to the shape of yourwork piece, enabling you to fixture unusual applications easily.The specially designed steel wedge spreads the clamping forceuniformly on both sides of the aluminum channel. A uniquelocking plate is provided to make the clamp rigid while machiningthe jaws to your specifications. Order one piece and you willreceive one complete assembly with mounting screws and lockingplate.
PRODUCTS INC.
Discount 143 applies.
Cat. No. A* B C D E F** G H I
PriceEach1-24
MB-250 1.125 .50 .62 .42 .25 .18 .400 2-56 8-32 21.25MB-750 1.50 .75 .94 .64 .38 .28 .625 6-32 1/4-20 22.50MB-1000 2.00 1.00 1.25 .82 .50 .38 .810 6-32 5/16-18 31.05MB-1500 3.00 1.50 1.87 1.87 .75 .62 1.20 10-32 1/2-13 86.15
*A is the distance needed between work pieces for clamp clearance,drill and tap mounting holes on the center of the A dimension.**F dimension is the amount of machinable stock.
Holding No. PriceThread Max Force Per Each
Cat. No. A B C D* E F** Size Spread Lbs. Pack 1-24MB-6025 .240 .250 .320 .210 .140 .250 2-56 .260 200 6 62.75MB-6037 .360 .375 .470 .310 .185 .375 4-40 .390 310 6 62.75MB-6050 .485 .500 .625 .410 .220 .500 8-32 .530 500 8 62.75MB-6075 .735 .750 .940 .635 .375 .750 1/4-20 .785 1,500 6 63.90MB-6100 .980 1.000 1.250 .820 .500 1.000 5/16-18 1.050 2,000 4 62.75MB-6150 1.470 1.500 1.875 1.215 .750 1.500 1/2-13 1.560 3,500 2 104.50
*A shallow slot a little wider than D dimension will insure clamp remainsin line with workpiece.**F is the distance needed between workpieces for clamp clearance.Drill and tap mounting hole on the center of F dimension.
0156.qxd 2/23/2010 12:49 PM Page 156
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 157
Clam
ps an
d W
orkh
old
ing
CLAMPING SYSTEMSSide-Loc Xpansion Clamps
H
G
E
H
F
C
AB
D
The side-loc xpansion clamp is an ideal way to clamp on the I.D.when the part has a blind bore. It is actuated by turning a sockethead cam on the side, which moves a tapered plunger to expandthe clamp. The side-loc xpansion clamp is designed in two styles,one for milling operations and one for lathe applications.Presently one size is available for each model. The mill side-locxpansion clamp can be machined from 1.120 to .710 and thelathe version from 2.09 to .710. The lathe version has a straightmounting shank of 1”.
Note: Six mounting screws included.
PRODUCTS INC.
Discount 143 applies.
A
C B
F
D
H
G
EMB-31210 MB-31370
Cat. No. A B C D E F G HHex Key
SizeHolding
Force Lbs.
PriceEach1-24
MB-31210 1.625 .875 .69 0.75 1.968 1.13 0.71 8-32 on 1.550 BHC M6 4,000 92.70MB-31370 1.750 1.00 .84 0.75 2.10 2.10 0.71 1.0 M6 4,000 136.00
Machinable Pitbull® Clamps
This new Pitbull® fixture clamp is a machinable version of thepopular Pitbull® clamp. The clamp has positive down force and avery low gripping profile. The machinable Pitbull® clamp is madeof tool steel and heat treated to about 43 Rc for long life, yet stillmachinable. There is additional material on the clamping face toallow for machining a radius. A dowel pin is included in eachpackage to locate the clamp during the machining process.
PRODUCTS INC.
Discount 143 applies.
DA
B
C
E
Cat. No. Description A B C D* EClampWidth
ScrewSize
Max. HoldingForce Lbs.
TorqueIn.-Lbs.
TotalThrow
DowelPin Size
NumberPer Pack
PriceEach1-24
MB-26077 Tool Steel, Machinable .400 .450 1.00 .250 .710 1.00 3/8-16 6,000 360 .050 1/8 4 83.05MB-26088 Tool Steel, Machinable .600 .640 1.50 .375 .770 1.50 1/2-13 12,000 1,300 .075 1/4 2 72.65*D is clamp height.
Modular Pitbull® ClampsF
D
C
B
A
G
E The slotted modular Pitbull® clamp with a step offers increasedversatility through its unique riser design. This clamp supports thework piece off the machine table for through milling and drilling.The hardened and ground clamps are designed for use on workcubes, as well as machined tables with tapped holes or T-slotconfigurations. The compact modular Pitbull® clamp is ideal forclamping work pieces in a series by using the back surface of aclamp to locate the next work piece. The back of the clamp isground square to the bottom for precise location of parts. Theheight of the clamp can be adjusted by the depth of the milledslot used to locate the clamp.
PRODUCTS INC.
Discount 143 applies.
F
BA
C
E
H*
MB-26220 MB-26230
MB-26240 MB-26250
Cat. No. Description A B C D E F G
HMax
MovementHolding
Force Lbs.
PriceEach1-24
MB-26220 Medium/Compact 2.25 1.23 .98 NA .62 1.50 — .024 3,600 59.45MB-26230 Large/Compact 2.70 1.48 1.24 NA .74 1.85 — .050 6,000 93.40MB-26240 Medium/Slotted 4.08 1.25 .99 .730 .36 1.70 .50 .024 3,600 63.70MB-26250 Large/Slotted 4.20 1.50 1.61 1.378 .36 1.52 .43 .050 6,000 169.75
ID Xpansion™ Clamps
These clamps are ideal to hold multiple parts on an insidediameter for machining on a machining center. These clampsare produced in 10 sizes and can hold internal diameters from.16” to 4.06”. Expand clamp approximately .005” over relaxeddiameter and machine to fit work piece bore.
• Ideal for secondary operations on lathe parts• Easily machined to size on lathe or mill• Excellent for palletized setups• Allows more parts per work cube or fixture plates• Clamp body made of mild steel for machinability• Tighten with hex key or hydraulic pull cylinders (drill clearance
hole for longer bolt into cylinder)• Three mounting screws included
PRODUCTS INC.
Discount 143 applies.
AC
D
J
B
F
I
+.000/-.002E
HMountingScrews
IThread
PriceEachCat. No. A B C D F G* J
MB-31000 .42 .30 .24 .12 .787 .29 .16 2-56 on .540 BHC 2-56 .16 36.70MB-31050 .86 .63 .59 .23 1.170 .49 .28 6-32 on .825 BHC 8-32 .30 36.70MB-31100 .98 .75 .59 .23 1.240 .56 .48 6-32 on .910 BHC 1/4-20 .50 36.70MB-31150 .98 .75 .59 .23 1.476 .79 .53 6-32 on 1.140 BHC 5/16-18 .56 39.05MB-31200 1.13 .88 .69 .25 1.968 1.06 .71 8-32 on 1.550 BHC 3/8-16 .71 50.80MB-31250 1.25 1.00 .81 .25 2.205 1.39 .90 8-32 on 1.790 BHC 1/2-13 .71 62.65MB-31300 1.56 1.25 1.06 .31 2.736 1.65 1.15 10-32 on 2.200 BHC 5/8-11 .79 80.30MB-31350 1.56 1.25 1.06 .31 2.972 2.03 1.15 10-32 on 2.515 BHC 5/8-11 .79 88.10MB-31400 1.79 1.48 1.27 .31 4.232 3.06 1.15 1/4-20 on 3.646 BHC 5/8-11 .79 140.10MB-31450 1.79 1.48 1.27 .31 5.232 4.06 1.15 1/4-20 on 4.648 BHC 5/8-11 .79 171.95MB-31500 1.79 1.48 1.27 .31 5.232 6.89 1.15 1/4-20 on 4.648 BHC 5/8-11 .79 484.10*The “G” dimension is the minimum diameter that the “F” dimension can be machined or turned (down) to.
0157.qxd 2/17/2010 3:16 PM Page 157
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!158
Cla
mp
s an
d W
ork
ho
ldin
gCLAMPING SYSTEMS
T-Slot Toe Clamps
A low profile cam action clamp with positive down force. Thisclamp is mounted in the T-slots of machine tables by sliding theclamp to the work piece and tightening the locking screw. Totaldistance of movement .100”. Two clamping edges, smooth formachined surface, and serrated for rough cut material.
PRODUCTS INC.
Discount 143 applies.
1.12
.62
1.94
.38
1.00
Cat. No. T-Slot Size
PriceEach1-24 Cat. No. T-Slot Size
PriceEach1-24
MB-24128 9/16 40.20 MB-24168 11/16 40.20MB-24148 5/8 40.20
Knife Edge Clamps
Low profile, fast cam action. Hardened steel bites into workpiecefor secure clamping for castings and rough cut stock. Followscontour of part for maximum contact.
PRODUCTS INC.
Discount 143 applies.
Thread ClampsPriceEach For
PriceEach
Cat. No. Size Per Pack 1-24 Cat. No. Set 1-24Sets Replacement WasherMB-22584 3/8-16 8 98.75 MB-12584 MB-22584 8.40MB-22588 1/2-13 8 115.95 MB-12588 MB-22588 8.85MB-22592 5/8-11 4 76.95 MB-12592 MB-22592 10.45
Compact Toe Clamps
Cam action, positive down force clamps can be used in series.Clamp base should be installed in a slot to retain location. Clampbase provides for higher clamping; height is determined by depthof slot. Mounting screws included.
PRODUCTS INC.
Discount 143 applies.
D
GF
C
AE
B
Total PriceDistance of Key Mounting Each
Cat. No. A B C D E F G Movement Size Screws 1-24MB-24106 1.70 .75 .50 1.00 .090 .75 .25 .050 3/16 5/16-18x3/4 39.10MB-24108 2.12 1.00 .45 1.32 .110 1.00 .38 .100 5/16 3/8-16x3/4 44.10
Pitbull® Clamps
The Pitbull® clamp is a revolu-tionary new fixture clamp withpositive down force and a lowgripping profile. High verticaland horizontal clamping forcesare generated, considering thesize of the Pitbull® Clamps. Ituses a standard cap screwand an oil resistant O-ring.The Pitbull® Clamp is availablein 5 sizes and several styles, atool steel knife edge foraggressive stock removal, atool steel blunt edge forgeneral purpose and a brassversion to help preventmarring in the work piece.
PRODUCTS INC.
Discount 14 applies.
Screw Size
Max. HoldingForce (Lbs.)
TotalThrow
NumberPer Pack
Price PerPackage
1-24Cat. No. Material/Edge A B CPBCL-1 Steel/Knife .150 .140 .375 4-40 650 .0075 8 74.60PBCL-2 Steel/Blunt .150 .140 .375 4-40 650 .0075 8 74.60PBCL-3 Brass/Blunt .150 .140 .375 4-40 650 .0075 8 74.60PBCL-4 Steel/Knife .200 .187 .500 8-32 1,500 .0160 8 79.20PBCL-5 Steel/Blunt .200 .187 .500 8-32 1,500 .0160 8 79.20PBCL-6 Brass/Blunt .200 .187 .500 8-32 1,500 .0160 8 79.20PBCL-7 Steel/Knife .300 .280 .750 1/4-20 3,600 .0240 6 76.80PBCL-8 Steel/Blunt .300 .280 .750 1/4-20 3,600 .0240 6 76.80PBCL-9 Brass/Blunt .300 .280 .750 1/4-20 3,600 .0240 6 76.80
OK Vise Low Profile ClampsThese hardened and ground clamps can produce holding forcesof over 19,000 lbs. The OK-Vise clamp achieves this by its cross-wedge construction, which allows the clamp to lock firmly in everydirection as it is tightened down. Jaws with 30-34 HRC can bemachined to suit the geometry of the workpiece. Includes mount-ing screws.
Single Wedge
Completely free of play.
PRODUCTS INC.
Discount 143 applies.
BD
F
OK-VISE A max.A min.
E
C
PressingForce of
Jaws (Lbs.)
Hardnessof Jaws(HRC)
A MountingScrew
PriceEachCat. No. Min. Optimum Max B C D E F
MB-471* 1.06 1.14 1.22 1.14 .59 .83 .10 .040 5/16-18x3/4 3,300 48-52 102.20MB-479 1.06 1.14 1.22 1.14 .59 .83 .10 .040 5/16-18x3/4 3,300 48-52 102.20MB-472 1.65 1.77 1.93 1.61 .87 1.18 .16 .080 1/2-13x11/4 6,600 48-52 151.55MB-474* 1.30 1.38 1.46 1.14 .59 .83 .10 .040 5/16-18x3/4 3,300 30-34 143.15MB-475 2.05 2.17 2.32 1.61 .87 1.18 .16 .080 1/2-13x11/4 6,600 30-34 217.65*Ends of jaws are smooth
Double Wedge
Pull down action towards the work piece.
PRODUCTS INC.
BD
F
OK-VISE
A max.A min.
E
CC1
Discount 143 applies.PressureForce of
Jaws (Lbs.)
Hardnessof Jaws(HRC)
A MountingScrew
PriceEachCat. No. Min. Opt. Max. B C C1 D E F
MB-477 1.65 1.77 1.93 1.61 1.42 1.18 1.18 .20 .080 1/2-13x11/2 11,000 48-52 214.00MB-478 2.24 2.40 2.64 2.20 1.97 1.65 1.65 .20 .120 5/8-11x21/4 19,800 48-52 359.50
0158.qxd 2/17/2010 3:16 PM Page 158
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 159
Clam
ps an
d W
orkh
old
ing
CLAMPING SYSTEMS
TalonGrip™ Vise Jaws SystemsSteel Vise Jaw SetSet includes 4 TalonGrips™, 1 stop with M5 screws.
TalonGrip™ vise jaws systems is a new and innovative productthat will increase the versatility of your standard 4” and 6” vises. Itis a simple bolt on system that will allow you to perform aggres-sive machining operations while clamping on as little as .060 ofan inch. Ideal for small lot sizes, difficult application or proto-typework when building a fixture would not be beneficial. TalonGrips™
are also available with the Pitbull® clamp or soft jaw applications.
PRODUCTS INC.
DC
B A
C
AD
B
E
Vise Jaw
Grip
TalonGrip™ Vise Jaw SystemsVise Jaw Grips and Stops
Cat. No. Description A B C DRecommendedGripping Height
PerPack Price Each
MB-32050 Grips .75 .500 .250 10-32 .060-.075 2 24.50MB-33050 Grips .75 .500 .250 M5 .060-.075 2 24.50MB-32025 Stop — — — 10-32 — 1 15.00MB-33025 Stop — — — M5 — 1 15.00
TalonGrip™ Vise Jaws SystemsFixture Grips
Cat. No. A B C DRecommendedGripping Height
PerPack Price Each
MB-32075 .75 .75 .312 10-32 .06-.120 2 27.50MB-33075 .75 .75 .312 M5 .06-.120 2 27.50MB-32100 .75 1.00 .312 10-32 .06-.120 2 30.25MB-33100 .75 1.00 .312 M5 .06-.120 2 30.25
VersaGrip™ Vise Jaws SystemsSteel Vise Jaw SetsSet includes 4 VersaGrips™
VersaGrip™ allows you the versatility of clamping standard visework as well as providing a solution for difficult applications thatwould normally require fixturing or machining soft-jaws. By simplyreplacing your current jaws with the VersaGrip™ system you cansecurely hold odd shaped parts while machining at speeds andfeeds you never thought possible. This system can accommodatea wide range of part sizes as well as holding multiple parts in asingle cycle. The hardened (52-54 RC) VersaGrip™ has penetrat-ing teeth designed to bite into your workpiece preventing lateraland horizontal movements. These grips will hold flame cut parts,castings, even parts with a negative draft.
PRODUCTS INC.
A
C
B
C
B
E
D
A
Vise Jaw
Grip
VersaGrip™ Vise Jaws SystemsVersaGrips™
Cat. No. A B CRecommendedGripping Height
PerPack Price Each
MB-32175 .750 .375 M5 .060-.140 2 35.00
CAM ACTION CLAMPS
Low profile quick action clamp. Jaw pivots forward and downwardat the same time when the handle is turned. Locks positively atany position within its 180° turn, so that it will hold parts that varyslightly in dimension. Clamps with extended base allow positionadjustment on machine tables.
Standard
Extended
Cat. No. Vise Size A B C D E Price EachMB-32044 4 2.5 .688 1.49 4.0 1.0 150.00MB-32066 4 / 6 2.5/3.88 .688/.94 1.74 6.0 1.0 170.00MB-32068 6 3.88 .94 1.74 8.0 1.0 190.00
Cat. No. Vise Size A B C D E Price EachMB-32166 4 / 6 6.00 1.88 1.0 2.5/3.88 .688/.94 185.00MB-32168 6 8.00 1.88 1.0 3.88 .94 200.00
Tool Sets
See pages735, 736, 738.
LifetimeGuarantee
Discount 143 applies.
Discount 143 applies.
Discount 143 applies.
Discount 143 applies.
Discount 143 applies.
Price Each1-11Cat. No. Base Stud A B C D E F G
CAC-5 Standard 5/16-18 11/4 1 15/8 13/4 5 1/8 — 63.41CAC-10 Extended 5/16-18* 11/4 1 15/8 31/8 5 1/8 1 71.68CAC-15 Standard 1/2-13 17/8 11/2 21/2 23/4 71/2 5/32 — 74.55CAC-20 Extended 1/2-13* 17/8 11/2 21/2 43/4 71/2 5/32 11/2 79.52*Stud not included in extended base clamps
0159.qxd 2/22/2010 9:25 AM Page 159
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!160
Cla
mp
s an
d W
ork
ho
ldin
gCLAMP ASSEMBLIES
Strap
Spherical washers compensate for irregularities between clampstrap and part being clamped allowing for more rigid clamping.Double end clamp straps can be used for clamping flat workpieces or they can be inverted for holding round work pieces inV-blocks or other nesting arrangements. All parts (except jamnuts) are heat treated steel with black oxide finish.
Cat. No. A B C D E F GThread
SizePrice Each
1-24ACA-107 7/8 5/8 3/8 21/2 1 21/4 7/8 1/4-20 23.63JCA-13515 13/4 11/4 5/8 31/2 11/8 31/2 17/16 3/8-16 25.18JCA-13516 13/4 11/4 5/8 41/2 15/8 31/2 17/16 3/8-16 29.75
Flange Nut
Used where high clamping pressures are needed and vibrationcould cause loosening. They have a spherical flange nut andwasher for greater flexibility. Extra long, true milled slot allowsmore clearance for placing and removing work.
F
GThreadSize
A
C
B
DE
PriceEachCat. No. A B C D E F G** Thread
JCA-12701* 3/4 5/8 1/2 2 5/8 15/8 7/8 1/4-20 27.49JCA-12703 11/2 11/4 7/8 31/2 11/8 215/16 17/16 3/8-16 33.74JCA-12705 11/2 11/4 7/8 41/2 15/8 215/16 115/16 3/8-16 36.86JCA-12707 11/8 11/2 11/8 41/2 11/4 3 21/8 1/2-13 39.99JCA-12710 11/8 11/2 11/8 6 2 3 27/8 1/2-13 36.94JCA-12711 25/8 13/4 13/8 5 11/2 51/16 21/8 5/8-11 43.70JCA-12713 25/8 13/4 13/8 7 21/2 51/16 31/8 5/8-11 46.34JCA-12714 13/4 13/4 11/2 5 11/2 43/8 21/8 3/4-10 50.71JCA-12716 13/4 13/4 11/2 7 21/2 43/8 31/8 3/4-10 54.19*Finger handle not included. See page 88 for finger handle.**G dimension represents an optimum dimension.
Radius End Flange Nut
For heavy duty clamping of plain surfaces with spherical flangenut and washer for angular flexibility. Radius end strap and springloaded stud for quick release.
F
GThreadSize
A
C
B
DE
Center CamSingle End
Note: See page 161 for additional steel cam handles.
Cat. No. A B C D E G HThread
SizePrice Each
1-24ACA-305 3/4 5/8 3/8 2 5/8 7/8 21/2 1/4-20 26.93ACA-307 3/4 5/8 3/8 2 1/2 1 7/8 21/2 1/4-20 27.62JCA-12513 11/8 7/8 1/2 21/2 3/4 11/4 37/16 5/16-18 34.82JCA-12514 11/8 7/8 1/2 31/2 11/4 11/4 37/16 5/16-18 34.82JCA-12515 11/2 11/4 5/8 31/2 11/8 17/16 37/16 3/8-16 36.58JCA-12516 11/2 11/4 5/8 41/2 15/8 17/16 37/16 3/8-16 37.31ACA-332 13/8 11/2 3/4 41/2 11/4 17/8 5 1/2-13 55.00JCA-12518 13/8 11/2 3/4 6 2 1/7/8 5 1/2-13 54.55JCA-12519 15/8 13/4 7/8 5 11/2 115/16 51/16 5/8-11 54.55
Center CamDouble End
Note: See page 161 for additional steel cam handles.
Cat. No. Jergens A B C D E HThread
Size
PriceEach1-24
ACA-350 12523 13/8 11/2 3/4 4 11/4 5 1/2-13 55.74ACA-354 12524 13/8 11/2 3/4 5 11/4 5 1/2-13 55.96ACA-368 12526 15/8 15/8 7/8 6 11/2 51/16 5/8-11 65.77
Double Cam
Features fast-action, light duty holding of plain surface workwhere quick movements are required in a restricted space. Longend slot for lateral adjustment. Spring loaded stud member understurdy double cam lever.
GThreadSize
A
C
B
DE
H
PriceEachCat. No. A B C D E G** H Thread
JCA-12501* 5/8 5/8 1/2 2 5/8 7/8 21/2 1/4-20 51.24JCA-12502 15/16 11/4 7/8 31/2 11/8 17/16 37/16 3/8-16 58.75*Finger handle not included. See page 88 for finger handle.**G dimension represents an optimum dimension.
PriceEachCat. No. A B C D E F G** Thread
JCA-14103 7/8 5/8 3/8 2 5/8 15/8 7/8 1/4-20 25.32JCA-14105 13/4 11/4 5/8 31/2 11/8 215/16 17/16 3/8-16 29.37JCA-14108 11/2 11/2 3/4 41/2 11/4 3 17/8 1/2-13 35.61JCA-14111 31/8 13/4 7/8 5 11/2 51/16 2 5/8-11 47.50JCA-14114 21/4 13/4 1 5 11/2 43/8 21/8 3/4-10 55.00
PriceEachCat. No. A B C D E F G Thread
JCA-14123 7/8 5/8 3/8 2 1 15/8 11/16 1/4-20 21.08JCA-14125 13/4 11/4 5/8 31/2 11/2 215/16 11/4 3/8-16 27.65JCA-14128 11/2 11/2 3/4 41/2 113/16 3 115/16 1/2-13 29.87JCA-14134 21/4 13/4 1 5 21/16 43/8 23/16 3/4-10 45.88
Radius Swing
0160.qxd 2/17/2010 3:17 PM Page 160
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 161
Clam
ps an
d W
orkh
old
ing
A
DE
L
C
G
B
CLAMP ASSEMBLIESSwing Clamp Assemblies
Very useful in limited space applications. Knob swivel screwassembly allows for quick clamping and release and for protectionagainst marring the work piece.The shoe of the swivel screwstops rotation upon contact with the work piece. To compensatefor irregular work surfaces, the shoe swivels approximately threedegrees in all directions. Arm may be used for right or left handswing. Knob and arm are cadmium plated cast iron. All otherparts are heat treated steel with black oxide finish.
Reamed Hole Mounting
C
B
A
D
D
Cat. No. A+.000/-.001
B C DThreadTravel
PriceEach
SCA-21205 2 .874 11/8 1/2-13 1.00 79.28SCA-21219 3 1.123 13/8 5/8-11 1.50 79.28
Flange Base
H
A
E
F
AlternateStop PinLocations
G
B
C
D
ThreadTravel
PriceEachCat. No. A B C D E F G H
SCA-21202 11/2 1 17/16 11/2 3/4 1 #10 5/16-18 .40 51.67SCA-21211 3 1.25 21/4 21/4 11/8 13/8 1/4 1/2-13 1.00 84.23SCA-21223 4 1.25 21/4 21/4 11/4 11/2 3/8 5/8-11 1.25 98.31
Hook Clamp Assemblies
Alloy steel, black oxide finish. Ideal for jig and fixture quick buildsystems. Hook rotates 360°. Screws and springs provided.
Bold catalog numbers conform to TCMAI Standards.
C
B
FCap
Screw
AReam
C
B
GStud
AReam
D
E
FCap
Screw
Cap ScrewF
Stud/NutG
PriceEachCat. No. A B C D E
HCA-C1 .625 15/16 1/2 11/16 3/8 5/16-18 x 13/4 — 22.27HCA-S1 .625 15/16 1/2 11/16 3/8 — 5/16-18 x 21/2 22.27HCA-C2 .875 15/8 5/8 1 1/2 1/2-13 x 3 — 25.56HCA-S2 .875 15/8 5/8 1 1/2 — 1/2-13 x 4 25.56HCA-C3 1.125 113/16 7/8 17/16 3/4 5/8-11 x 31/2 — 28.66HCA-S3 1.125 113/16 7/8 17/16 3/4 — 5/8-11 x 5 28.66
Clamp Rests
Cat. No. A B C D E F GThread
SizePrice Each
1-24ACA-200 11/4 7/16 5/32 5/64 11/64 1 29/32 1/4-20 2.94ACA-205 17/8 1/2 7/32 3/16 7/32 115/32 15/16 5/16-18 3.13ACA-210 31/4 1/2 7/32 3/16 7/32 227/32 211/16 5/16-18 4.77ACA-220 21/2 9/16 11/32 5/32 11/32 2 113/16 3/8-16 4.04ACA-225 23/8 7/8 11/32 3/16 1/2 111/16 11/2 1/2-13 3.90ACA-230 37/8 9/16 11/32 5/32 11/32 33/8 33/16 3/8-16 3.77ACA-235 37/8 7/8 11/32 3/16 1/2 33/16 3 1/2-13 4.88ACA-240 25/8 7/8 11/32 3/16 1/2 115/16 111/16 5/8-11 5.04ACA-245 327/32 7/8 11/32 3/16 1/2 35/32 215/16 5/8-11 6.25ACA-250 23/4 7/8 11/32 3/16 1/2 21/16 17/8 3/4-10 6.16ACA-255 31/2 7/8 11/32 3/16 1/2 213/16 23/8 3/4-10 6.83
Cat. No. A B C D E F G HPrice Each
1-24InchJCA-35901 1 1 2 0.475 3/8 1/2 #10 11/2 11.15JCA-35902 11/2 11/2 21/2 0.60 1/2 1/2 1/4 2 15.78JCA-35904 1 2 31/2 0.720 5/8 3/4 5/16 23/4 15.78JCA-35905 1 3 41/2 0.720 5/8 3/4 5/16 33/4 18.60JCA-35906 1 4 51/2 0.720 5/8 3/4 5/16 43/4 23.28MetricJCA-35951 25 25 50 12 10 13 M5 38 13.95JCA-35952 25 38 64 15 13 13 M6 50 19.70JCA-35954 25 50 89 18 16 19 M8 70 19.70
Clamp Rest Plates4-Hole
Cat. No. A B C D E F G H I JPrice Each
1-24InchJCA-35903 2 2 3 .725 1/2 1/2 1/4 21/2 1/2 1 24.58MetricJCA-35953 50 50 75 18 12 13 M6 64 13 25 27.33
STEEL CAMS
These cams provide quick action locking with high holdingpressure. Can be used for many types of operations. Heat treatedfor long life. Black oxide finish. The slot on the double cam ismilled. Can be used with our eye bolts or forged rod ends. Seepage 192.Discount 22 applies.
Double Single
Cat. No. A B C D E F G H LPrice Each
1-25DoubleDC-1 21/2 9/16 1/4 3/16 1/16 3/8 3/16 9/16 — 13.16DC-2 31/2 5/8 5/16 1/4 1/16 1/2 9/32 11/16 — 15.39DC-3 5 11/8 1/2 3/8 7/64 5/8 13/32 15/16 — 19.38DC-4 53/8 11/4 5/8 5/8 9/64 7/8 9/16 13/16 — 21.83SingleSC-0 23/8 5/32 3/16 7/16 1/4 — 17/32 — 1/8 7.93SC-15 31/4 1/4 1/4 1/2 1/4 — 5/8 — 3/16 8.93SC-1A 41/2 5/16 3/8 5/8 5/16 — 25/32 — 15/32 9.70SC-2A 5 3/8 1/2 29/32 3/8 — 15/64 — 1/4 12.09
Clamp Rest Plates2-Hole
0161.qxd 2/17/2010 3:17 PM Page 161
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!162
Cla
mp
s an
d W
ork
ho
ldin
gSTRAP CLAMPS
Tapped End RadiusHeat Treated Steel
The specially designed end provides maximum pressure for edgeclamping. Long slot allows for lateral adjustment.Cat. No. A B C D E F G H Price EachCTE-2 1/4 2 3/8 5/8 1/2 1 7/32 1/4-20 6.69CTE-4 1/4 21/2 3/8 5/8 1/2 11/8 7/32 1/4-20 6.97CTE-6 5/16 23/4 1/2 1 7/16 11/2 9/32 5/16-18 8.58CTE-8 5/16 31/4 1/2 1 13/16 11/2 9/32 5/16-18 9.08CTE-12 3/8 3 5/8 11/4 3/4 111/16 5/16 3/8-16 9.55CTE-14 3/8 4 5/8 11/4 1 23/16 5/16 3/8-16 11.84CTE-16 3/8 5 5/8 11/4 11/2 211/16 5/16 3/8-16 12.63CTE-18 1/2 4 5/8 11/4 1 21/4 7/16 1/2-13 11.75CTE-20 1/2 41/2 5/8 11/4 11/2 21/4 7/16 1/2-13 12.53CTE-22 1/2 5 5/8 11/4 11/2 21/4 7/16 1/2-13 13.19CTE-24 1/2 6 5/8 11/4 11/2 21/4 7/16 1/2-13 14.70CTE-26 5/8 41/2 7/8 11/2 1 21/2 1/2 5/8-11 15.30CTE-28 5/8 5 7/8 11/2 11/2 21/2 1/2 5/8-11 16.99CTE-30 5/8 6 7/8 11/2 11/2 21/2 1/2 5/8-11 19.10
Single End RadiusHeat Treated Steel
The long slot increases the length of strap, allowing more clamp-ing pressure to be applied to the part. Finger grip on both sides ofthe clamp allows for easier lateral travel adjustments.Cat. No. A B C D E F G H Price EachCSE-2 1/4 2 3/8 5/8 1/2 1 3/16 1/8 5.02CSE-4 1/4 21/2 3/8 5/8 1/2 11/8 3/16 1/8 6.97CSE-6 5/16 23/4 1/2 1 7/16 11/2 1/4 3/16 8.58CSE-8 5/16 31/4 1/2 1 13/16 11/2 1/4 3/16 9.08CSE-12 3/8 3 5/8 11/4 3/4 111/16 3/8 9/32 10.52CSE-14 3/8 4 5/8 11/4 1 23/16 3/8 9/32 11.84CSE-18 1/2 4 5/8 11/4 1 21/4 3/8 9/32 11.84CSE-20 1/2 41/2 5/8 11/4 11/2 21/4 3/8 9/32 12.63CSE-22 1/2 5 5/8 11/4 11/2 21/4 3/8 9/32 13.19CSE-24 1/2 6 5/8 11/4 11/2 21/4 3/8 9/32 14.51CSE-26 5/8 41/2 7/8 11/2 1 21/2 1/2 9/32 15.30CSE-30 5/8 6 7/8 11/2 11/2 21/2 1/2 9/32 19.10CSE-32 3/4 6 1 13/4 13/4 31/4 1/2 5/16 24.85
Tapped End Radius304 Stainless Steel
Cat. No. A B C D E G H J Price EachCSS-1503 1/4 1/2 11/2 5/16 5/8 10-32 7/32 11/16 12.94CSS-1504 1/4 1/2 13/4 7/16 3/4 10-32 7/32 13/16 13.50CSS-1629 5/16 5/8 2 1/2 7/8 1/4-20 9/32 7/8 16.88CSS-1755 3/8 3/4 3 7/8 15/16 5/16-18 11/32 13/8 19.13CSS-1878 1/2 7/8 3 3/4 15/16 3/8-16 13/32 15/16 24.53
Flat 304 Stainless Steel
Cat. No. A B C D E F G Price EachCSS-1632 1/4 5/8 13/4 1/2 3/4 9/32 1/8 14.40CSS-1881 1/2 7/8 3 1 13/8 13/32 1/8 19.13
Radius304 Stainless Steel
PriceEachCat. No. A B C D E G H
CSS-1501 1/4 1/2 13/4 7/16 3/4 3/32 7/32 12.71CSS-1876 1/2 7/8 31/2 1 11/2 1/8 13/32 24.53
Tempered Steel - Varnished FinishPlain
Cat. No. A Bolt Size B C D E F GPrice Each
AMF-9 .43 M10 or 3/8 3.15 .59 1.18 .47 .59 1.18 11.03AMF-10 .55 M12, M14 or 1/2 3.94 .79 1.57 .55 .83 1.57 13.35AMF-12 .71 M16, M18 or 5/8 4.92 .98 1.97 .71 1.02 1.77 18.59AMF-13 .71 M16, M18 or 5/8 6.30 .98 1.97 .71 1.02 2.56 24.38AMF-14 .87 M20, M22 or 3/4 6.30 1.18 2.36 .87 1.18 2.36 35.43AMF-15 .71 M20, M22 or 3/4 7.87 1.18 2.36 .87 1.18 3.15 44.15
Tempered Steel - Varnished FinishSingle Goose-Neck
Cat. No. A Bolt Size B C D E F G H JPriceEach
AMF-35 .55 M12, M14 or 1/2 4.92 .79 1.57 .79 .63 1.57 1.57 1.10 20.39AMF-38 .87 M20, M22 or 3/4 6.30 1.18 2.36 1.18 .94 2.17 2.17 1.74 48.24
Tempered Steel - Varnished FinishForked Clamp with Shoe
Price EachCat. No. A Bolt Size B C D E G H
AMF-34 .87 M20, M22 or 3/4 9.84 1.58 2.36 1.38 1.77 2.68 74.08
Tempered Steel - Varnished FinishStep Clamps
Compatible with universal step blocks AMF-40, 41, and 42.
Cat. No. A Bolt Size B C D E F G Price EachAMF-17 .43 M10 or 3/8 3.15 .59 1.18 .47 .59 1.18 16.50AMF-18 .55 M12, M14 or 1/2 3.94 .79 1.57 .55 .83 1.57 19.02
Plain Clamps with Adjusting Screw
Best suited for low work pieces. Clamping height is easilyadjusted with adjusting screw. Adjusting screw (included) hasknurled screw or socket head. Made from tempered steel,varnished finish. See pages 187 and 190 for T-bolts and nuts.Cat. No. A B C D E* Slot Width Price EachAMF-1 3.94 .83 1.58 M12 .39-1.81 .55 31.95AMF-2 4.92 1.02 1.77 M16 .51-2.05 .71 47.40AMF-3 6.30 1.18 2.36 M20 .63-2.56 .87 76.19*Depends on depth of slot and position of fixture nut
0162.qxd 2/23/2010 12:50 PM Page 162
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 163
Clam
ps an
d W
orkh
old
ing
CLAMPSDrop-Forged Steel Clamps
Forged from 1030 steel for toughness. Because of draft or taperon forgings minimum dimensions of slot are given.
Plain Slot Pattern
Slot PriceEachCat. No. Lgth. Width Thickness Lgth. Width
PS-4 4 15/8 3/4 13/8 11/16 8.65PS-6 6 13/4 7/8 21/16 11/16 13.73PS-8 8 21/8 11/8 213/16 13/16 22.28PS-10 10 21/2 13/8 311/16 15/16 42.12
Screw Heel
Slot PriceEachCat. No. Lgth. Width Thickness Lgth. Width Screw
PS-12 4 15/8 3/4 15/16 11/16 1/2-13 x 11/4 19.99PS-14 6 13/4 7/8 111/16 11/16 5/8-11 x 11/2 27.97PS-16 8 21/8 11/8 27/16 13/16 3/4-10 x 13/4 40.00
Goose Neck Pattern
Slot NeckOffset
PriceEachCat. No. Lgth. Width Thickness Lgth. Width
GN-4 4 13/8 3/4 15/16 11/16 13/16 9.22GN-6 6 13/4 7/8 111/16 11/16 15/16 16.53GN-8 8 21/8 11/8 27/16 13/16 11/8 23.59
“U” Pattern
Slot PriceEachCat. No. Lgth. Width Thickness Lgth. Width
UP-4 4 13/4 3/4 31/2 11/16 8.65UP-6 6 2 7/8 51/2 11/16 14.45UP-8 8 23/8 11/8 73/8 13/16 22.28UP-10 10 23/4 11/4 9 15/16 35.22UP-12 12 31/4 13/8 11 11/16 48.15
SET UP WEDGES
Max.Thickness
PriceEachCat. No. Lgth. Width
SUW-950 3 1 1/4 6.03SUW-951 5 1 1/2 8.44SUW-952 6 11/4 3/4 9.78
ADJUSTABLE CLAMPSRite Hite Self Positioning Hold Down Clamps
These clamps have instant adjustment up to 5”. The main body ofthe clamp will move from 0” to whatever the max. height of theparticular clamp is, instantly. Two models are available; longerreach for normal requirements and shorter reach where tablespace is at a premium. Up to 65,000 lbs. load limits. Clamps havea rocker design which allows for “instant set-ups” when held inplace by a T-nut in a T-slot. Use with T-nuts on page 188 andset-up studs on page 189.
MaxStudSize
LoadLimit(Lbs.)
ClampingRange
PriceEachCat. No. Dimensions
Longer ReachJMC-375 3/8 0-11/4 11/8 x 31/2 7,000 35.91JMC-500 1/2 0-21/2 17/16 x 53/4 8,800 39.12JMC-625 5/8 0-31/2 17/8 x 63/4 14,500 46.09JMC-750 3/4 0-5 21/8 x 9 24,000 67.53Shorter ReachJMC-376 3/8 0-1 11/8 x 3 8,800 34.83JMC-501 1/2 0-13/4 13/8 x 41/4 13,200 38.05JMC-626 5/8 0-23/4 17/8 x 51/2 19,000 45.02
Stepless Universal Height Clamps
Quickly adapts to various clamping heights without supports orblocks. Allows for quick set-ups. Holds work on planers, boringmills, milling machines and other applications. Made fromhardened steel, yellow passivated. See pages 187 and 190 forT-bolts and nuts.
Price EachCat. No. A B C D E F G H J L 1-25AMF-6 2.24 0-1.38 .51 1.50 3.47 1.10 1.89 .91 2.68 .55 34.38AMF-7 3.54 0-2.17 .71 2.21 5.12 1.50 2.91 1.14 3.98 .71 42.76AMF-8 4.06 0-2.56 .87 2.60 5.51 1.81 3.15 1.26 4.41 .79 55.16
Universal Adjustable Strap Clamps
Drop forged from selected hardenedcarbon steel. Holds work on planers,boring mills, face plates of lathes,milling machines and many otherapplications.
ClampWidth
MaximumT-Bolt Dia.Cat. No. OAL Adjustment Price Each
USC-1 51/16 15/8 21/4 5/8 40.82USC-2 8 13/4 4 3/4 74.34
One Piece Adjustable Clamps
Forged steel clamp offers instant height adjustment withoutblocks or shims. One piece assembly allows quick setups.Removable brass shims protect machine table and work piece.Clamp swings 90° in either direction for loading clearance. Seepages 187 and 190 for T-slot bolts and flange nuts for usewith these clamps.
C
BA
D
StudSize
ClampingRange
Price Each1-49Cat. No. A B C D
USC-40 17/8 11/8 1 11/4 3/8 0-13/4 22.25USC-50 25/16 17/16 17/16 15/8 1/2 0-21/16 24.34USC-60 31/4 2 17/8 17/8 5/8 0-3 34.78USC-70 31/2 21/8 21/4 25/8 3/4 0-41/4 52.88
0163.qxd 2/23/2010 12:51 PM Page 163
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!164
Cla
mp
s an
d W
ork
ho
ldin
gSTRAP CLAMPS
Strap Clamp Spring Lifters
Designed to speed set-ups wherever strap clamps are used.Spring lifter slides over T-slot bolt or stud and is held by tighteningthe set screw on locking collar. The strap clamp rests on thesupport collar and the spring holds the clamp just above the finaltightened height, permitting the work to be quickly and easily slidunderneath.Cat. No. Fits Dia. Price Each Cat. No. Fits Dia. Price EachSCL-801 1/4 4.92 SCL-805 5/8 5.94SCL-803 3/8 5.52 SCL-806 3/4 8.81SCL-804 1/2 5.41
ADJUSTABLE CLAMP RESTS
Cat. No. A B C D E Price EachCSS-6205 1 .190 3/4 10-32 1/16 2.30CSS-6256 1 1/4 11/16 1/4-20 5/64 2.32CSS-6258 11/2 1/4 13/16 1/4-20 5/64 2.54CSS-6320 15/8 5/16 13/8 5/16-18 3/32 3.20CSS-6321 17/8 5/16 15/8 5/16-18 3/32 3.20CSS-6382 15/8 3/8 13/8 3/8-16 1/8 3.60CSS-6384 25/8 3/8 23/8 3/8-16 1/8 3.83
UNIVERSAL STEP BLOCKS
Tempered steel, varnished finish. Step increments are vertically.183” and horizontally .091”. Step blocks sold individually. For usewith AMF step clamps AMF-17 and 18.
Cat. No. A B C D E Price EachAMF-40 .87 2.01 1.30 .75 1.50 5.36AMF-41 1.54 4.21 2.60 1.40 2.76 9.87AMF-42 2.80 8.19 5.16 2.68 5.32 24.38
CLAMPSPlain and Positive Grip Step Clamps
Machined from solid bar stock, case hardened and black oxidefinish. When used in conjunction with step setup blocks, positivegrip step clamps simplify and quicken setting up operationsconsiderably. Eliminates shimming to obtain the right height.
Note: Clamps for 5/16, 3/8, 1/2 and 5/8 bolts work with metric bolts M8,M10, M12 and M16 respectively.
Plain Grip Positive Grip
PlainCat. No.
PositiveCat. No.
BoltSize
SlotLgth.
Price EachOAL Width Thickness Plain Positive
CP-1 CS-1 5/16 or 3/8 21/2 1 1/2 11/4 9.28 9.87CP-2 CS-2 5/16 or 3/8 4 1 5/8 17/8 12.75 13.43CP-3 CS-3 5/16 or 3/8 6 11/8 3/4 25/8 15.94 17.10CP-4 CS-4 1/2 2 1/2 11/8 1/2 11/4 10.44 10.85CP-5 CS-5 1/2 4 11/4 3/4 17/8 14.55 15.18CP-6 CS-6 1/2 6 11/4 7/8 25/8 18.41 19.26CP-7 CS-7 5/8 21/2 11/4 5/8 11/4 13.06 13.98CP-8 CS-8 5/8 4 11/2 3/4 17/8 16.01 19.55CP-9 CS-9 5/8 6 11/2 7/8 25/8 20.77 23.19CP-10 CS-10 3/4 4 11/2 3/4 17/8 16.90 20.90CP-11 CS-11 3/4 6 15/8 1 23/4 24.64 29.03CP-12 CS-12 3/4 8 13/4 11/8 3 32.96 36.56
POSITIVE GRIP STEP SETUP BLOCKSHardened Steel or Aluminum
Two triangular pieces make up one block.
Bold catalog numbers conform to TCMAI standards.
Horizontal
Vertical
Steel Blocks Aluminum BlocksRange Width Cat. No. Price Each Cat. No. Price Each
3/4 to 11/2 1 1-S 4.98 1-A 5.1111/8 to 21/2 1 2-S 7.03 2-A 7.1621/2 to 6 1 3-S 17.36 3-A 17.67
13/4 to 33/4 11/2 4-S 11.1221/2 to 6 11/2 5-S 22.5631/2 to 9 11/2 6-S 43.55
13/4 to 33/4 2 7-S 14.2621/2 to 6 2 8-S 29.0331/2 to 9 2 9-S 54.29
0164.qxd 2/17/2010 3:19 PM Page 164
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 165
Clam
ps an
d W
orkh
old
ing
Toe Clamps
Powerful, low profile clamp that grips on the side of the workleaving the top surface open. No interference with cutting tools orreading and measuring instruments. Ideal for use on mills,planers, jig bores, drill presses or faceplates. Heat treated steel,black oxide finish. Toe is moved by an actuating screw. T-Wrenches are sold separately below. Toe moves on a 45° angleforcing workpiece down. 3° taper prevents back-off. A specialwasher, to help prevent possible damage by the anchor screw, isprovided with each clamp. See page 278 for socket head capscrews. See page 188 for T-slot nuts. Other sizes of brass toesavailable as special order. Call for price and delivery.
Slotted for 5/16 or M8 Socket Head Cap Screw
Price Each
Steel ToeCat. No.
Brass ToeCat. No.
SteelToe
BrassToeA B C D E F G H
Low GripNTC-41101 NTC-41131 2 1/2 1/16 3/4 1/8 5/8 1 — 39.12 45.51NTC-41102 — 21/2 1/2 1/16 11/4 1/8 5/8 1 — 41.80 —NTC-41103 — 3 1/2 1/16 13/4 1/8 5/8 1 — 44.49 —High GripNTC-41110 NTC-41121 2 1/2 1/16 3/4 — 5/8 1 5/8 41.98 47.33NTC-41111 — 21/2 1/2 1/16 11/4 — 5/8 1 5/8 44.66 —NTC-41112 — 3 1/2 1/16 13/4 — 5/8 1 5/8 47.39 —
Slotted for 1/2 or M12 Socket Head Cap Screw
Low Grip High Grip
Steel ToeCat. No.
PriceEachA B C D E F G H
Low GripNTC-41001 41/16 13/16 1/8 2 1/4 7/8 11/2 — 39.81NTC-41002 51/2 13/16 1/2 23/4 1/4 7/8 11/2 — 42.28NTC-41003 77/16 13/16 1 33/4 1/4 7/8 11/2 — 45.14High GripNTC-41010 41/16 13/16 1/8 2 — 7/8 11/2 7/8 42.68NTC-41011 51/2 13/16 1/2 23/4 — 7/8 11/2 7/8 45.23NTC-41012 77/16 13/16 1 33/4 — 7/8 11/2 7/8 48.07
Slotted for 5/8 or M16 Socket Head Cap ScrewSteel Toe Price
EachCat. No. A B C D E F G HLow GripNTC-41051 41/16 13/16 1/8 2 1/4 7/8 11/2 — 41.54NTC-41052 51/2 13/16 1/2 23/4 1/4 7/8 11/2 — 44.29High GripNTC-41061 41/16 13/16 1/8 2 — 7/8 11/2 7/8 47.46NTC-41062 51/2 13/16 1/2 23/4 — 7/8 11/2 7/8 50.23
CLAMPS
Bold catalog numbers conform to TCMAI standards.
T-Slot ClampDrop Forged Steel
Each clamp is furnished with one T-slot bolt, nut and washer.Used for holding down work on planers, drill presses, millingmachines and other machines having slotted tables. Clamp isfixed in desired position by tightening nut and work is held bytightening down screw. The heavy duty heat-treated screw isequipped with sliding pin handle. The point is equipped with a V-slotted patented, ball-joint swivel pad (that cannot come off) tofacilitate holding small rounds in addition to flat surfaces.
Approx.Weight
Lbs.T-Slot Bolt
SizePriceEachCat. No. Capacity Clamping Depth
TSC-712 0-21/4 1/2x11/2 2 2.29 202.00
Quick Acting Hold Down Clamps
For holding where thickness and surface are not exact from partto part. Offers quick-set and release with adjustable pressureafter clamping. High tensile strength. Can be bolted or weldeddown or T-Slot can be used for milling tables. KT-411 and KT-423do not come with a base plate. KT-411-2 and KT-423-1 come witha T-Slot base and bolt.
ECA
DB
RatedLoad Lbs.
PriceEachCat. No. A B C D E
KT-411 19/10 11/2 211/16 21/4 4 1,500 21.06KT-411-2 T-Slot — 211/16 21/4 41/8 1,500 28.11KT-423 29/10 25/8 33/4 33/4 67/8 3,200 40.27KT-423-1 T-Slot — 33/4 4 71/4 3,200 57.42
JACK SCREWS
Jack screws are used in fixtures to support irregularly shapedwork pieces, such as castings and to eliminate bowing or warpingof thinner materials during machining. Heat treated steel, blackoxide finish.
Staight Knurl
E
Price Each1-24Cat. No. A B C D E
SJS-500 3/8-16 11/4 11/8 17/8 3/8 6.29SJS-510 3/8-16 15/8 11/8 21/4 3/8 6.29SJS-515 3/8-16 2 11/8 25/8 3/8 6.65SJS-520 1/2-13 11/4 11/8 17/8 3/8 6.65SJS-525 1/2-13 15/8 11/8 21/4 3/8 7.03SJS-530 1/2-13 2 11/8 25/8 3/8 7.03SJS-535 1/2-13 21/2 11/8 31/8 3/8 7.19SJS-540 5/8-11 15/8 13/8 21/4 3/8 6.59SJS-545 5/8-11 2 13/8 25/8 3/8 6.59SJS-550 5/8-11 21/2 13/8 31/8 3/8 7.31
FIXTURE JACKS F
D
C
E
ThreadSize
G
A
B
J
Radius Head
Designed as a positive locking jack for irregular clamping toachieve various heights requiring a positive pressure stop onmilling fixtures, drill jigs, etc. Adjustable to fit irregularities ofmilling operations. Available in either smooth round head orhardened serrated gripping surface. Pin construction elevatesvertically, no rotation Outer diameter of bushing ground for pressfit. Made of ledloy, heat treated. Black oxide finish.
Serrated Head
D PriceEachCat. No. A B C Min. Max. E F G J Thread
Radius HeadJFJ-24901 5/8 13/16 3/16 9/16 11/2 1 1/4 5/32 3/8 3/8-16 24.37JFJ-24902 1 15/8 3/16 7/8 27/16 15/16 15/32 7/16 7/16 5/8-11 25.86JFJ-24903 11/2 23/4 3/16 7/8 31/2 13/4 13/16 1/2 9/16 1-8 29.80Serrated HeadJFJ-25101 5/8 13/16 3/16 9/16 11/2 1 1/4 5/32 3/8 3/8-16 27.33JFJ-25102 1 15/8 3/16 7/8 27/16 15/16 15/32 7/16 7/16 5/8-11 28.88JFJ-25103 11/2 23/4 3/16 7/8 31/2 13/4 13/16 1/2 9/16 1-8 33.69
High GripLow Grip
0165.qxd 2/17/2010 3:19 PM Page 165
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!166
Cla
mp
s an
d W
ork
ho
ldin
gSWIVEL PAD CLAMPS
Steel or Delrin Pads
Knurled Head Steel Body
Used where fingertip clamping is sufficient. Wide knurled headgives good gripping. Made of heat treated alloy steel. Pad swivels7 1/2° each side of centerline in all directions. Large, flat pad faceassures tighter clamping. Screw torque absorbed by pad. Conicalseat distributes clamping pressure uniformly. Ball joint construc-tion provides smooth angle adjustment and rotation of pad underpressure. Black oxide finish. Delrin pads eliminate marring whenclamping softer materials and help to eliminate distortion.
Bold catalog numbers conform to TCMAI standards.
*Load rating applies to steel pads only
Steel LoadLbs.*
Price Each1-11Steel Pad
Cat. No.Delrin PadCat. No. A B C D E Steel Delrin
AM-1 CM-1 1/4-20 11/2 3/8 1 .185 900 7.40 7.48AM-2 CM-2 1/4-20 2 3/8 1 .185 900 7.48 7.71AM-3 CM-3 5/16-18 11/2 7/16 11/8 .240 2,290 7.25 7.63AM-4 CM-4 5/16-18 2 7/16 11/8 .240 2,290 7.25 7.63AM-5 CM-5 5/16-18 21/2 7/16 11/8 .240 2,290 7.48 7.86AM-6 CM-6 3/8-16 11/2 1/2 11/4 .293 3,340 7.71 8.30AM-7 CM-7 3/8-16 2 1/2 11/4 .293 3,340 7.86 8.30AM-8 CM-8 3/8-16 21/2 1/2 11/4 .293 3,340 8.36 8.65AM-9 CM-9 3/8-16 3 1/2 11/4 .293 3,340 8.36 8.65AM-10 CM-10 1/2-13 11/2 9/16 11/4 .400 7,300 8.72 9.20AM-11 CM-11 1/2-13 2 9/16 11/4 .400 7,300 8.72 9.20AM-12 CM-12 1/2-13 21/2 9/16 11/4 .400 7,300 9.73 9.86AM-13 CM-13 1/2-13 3 9/16 11/4 .400 7,300 9.73 9.86
Socket HeadSteel Body
Same general construction as knurled head swivel pad clampsdescribed at top of page. Used on holding applications whereeither maximum rigidity is necessary or where space is limited.Strong accurate sockets for maximum clamping leverage.
Steel PadCat. No.
DelrinPadCat. No.
HexE
Steel LoadLbs.*
Price Each1-11
A B C D Steel DelrinAD-0 CD-0 10-32 11/32 1/2 .146 3/32 500 4.39 4.57AD-1 CD-1 1/4-20 11/32 1/2 .185 1/8 900 3.72 4.02AD-2 CD-2 1/4-20 19/32 3/4 .185 1/8 900 3.94 4.30AD-3 CD-3 1/4-20 27/32 1 .185 1/8 900 4.02 4.30AD-4 CD-4 1/4-20 111/32 11/2 .185 1/8 900 4.10 4.51AD-5 CD-5 5/16-18 35/64 3/4 .240 5/32 2,290 4.02 4.39AD-6 CD-6 5/16-18 51/64 1 .240 5/32 2,290 4.30 4.57AD-7 CD-7 5/16-18 119/64 11/2 .240 5/32 2,290 4.60 4.87AD-8 CD-8 5/16-18 151/64 2 .240 5/32 2,290 5.36 5.65AD-9 CD-9 3/8-16 1/2 3/4 .293 3/16 3,340 4.02 4.39AD-10 CD-10 3/8-16 3/4 1 .293 3/16 3,340 4.51 4.69AD-11 CD-11 3/8-16 11/4 11/2 .297 3/16 3,340 4.65 5.11AD-12 CD-12 3/8-16 13/4 2 .293 3/16 3,340 5.36 5.65AD-13 CD-13 1/2-13 7/16 3/4 .400 1/4 7,300 4.57 4.74AD-14 CD-14 1/2-13 11/16 1 .400 1/4 7,300 4.69 4.87AD-15 CD-15 1/2-13 13/16 11/2 .400 1/4 7,300 5.47 5.65AD-16 CD-16 1/2-13 111/16 2 .400 1/4 7,300 5.90 6.02AD-17 CD-17 1/2-13 211/16 3 .400 1/4 7,300 5.95 6.38AD-18 CD-18 5/8-11 5/8 1 .506 5/16 11,700 6.66 5.65AD-19 CD-19 5/8-11 15/8 2 .506 5/16 11,700 7.75 7.58AD-20 CD-20 5/8-11 25/8 3 .506 5/16 11,700 8.65 7.75AD-21 CD-21 3/4-10 1 11/2 .625 3/8 15,000 8.06 6.72AD-22 CD-22 3/4-10 2 21/2 .625 3/8 15,000 10.03 8.53AD-23 CD-23 1-8 53/64 11/2 .813 9/16 21,000 13.22 9.86*Load rating applies to steel pads only
Stainless Steel Body
Stainless Steel Pad Delrin Pad
StainlessSteel PadCat. No.
Price EachDelrin PadCat. No.
1-11A B C D E Stainless Delrin
ADS-0 CDS-0 10-32 11/32 1/2 .146 3/32 5.93 6.17ADS-2 CDS-2 1/4-20 19/32 3/4 .185 1/8 5.42 5.64ADS-3 CDS-3 1/4-20 27/32 1 .185 1/8 5.42 5.64ADS-4 CDS-4 1/4-20 111/32 11/2 .185 1/8 5.53 5.24ADS-5 CDS-5 5/16-18 35/64 3/4 .240 5/32 5.42 5.13ADS-6 CDS-6 5/16-18 51/64 1 .240 5/32 5.93 6.17ADS-7 CDS-7 5/16-18 119/64 11/2 .240 5/32 6.32 6.60ADS-8 CDS-8 5/16-18 151/64 2 .240 5/32 6.70 7.67ADS-10 CDS-10 3/8-16 3/4 1 .293 3/16 6.09 6.35ADS-11 CDS-11 3/8-16 11/4 11/2 .293 3/16 6.41 6.68ADS-12 CDS-12 3/8-16 13/4 2 .293 3/16 7.37 7.67ADS-14 CDS-14 1/2-13 11/16 1 .400 1/4 6.32 6.60ADS-16 CDS-16 1/2-13 111/16 2 .400 1/4 7.96 8.29ADS-22 CDS-22 3/4-10 2 21/2 .625 3/8 13.55 14.11
TOGGLE SHOE CLAMPSThe toggle shoe is held in place with a retaining spring whichpermits the shoe to adjust itself a full 10° in all directions. Thetoggle shoes snap on for quick assembly and are small enough toeliminate interference. Both shoe and screw are heat treated.Retaining springs available below.
Powdered Metal Hand Knob
A
Complete AssemblyToggle Clamps
w/o ShoesToggle
Dia.ShoeLgth.
KnobDia.
PriceEach
Price Each1-99Cat. No. Thread A Cat. No.
TA-141 1/4-20 13/16 5/16 3/16 11/8 5.69 T-141 4.98TA-142 1/4-20 115/16 5/16 3/16 11/8 5.79 T-142 5.11TA-143 1/4-20 211/16 5/16 3/16 11/8 5.97 T-143 5.29TA-144 1/4-20 37/16 5/16 3/16 11/8 6.31 T-144 5.66TA-561 5/16-18 11/4 3/8 7/32 11/2 6.44 T-561 5.70TA-562 5/16-18 2 3/8 7/32 11/2 6.61 T-562 5.90TA-563 5/16-18 23/4 3/8 7/32 11/2 6.85 T-563 6.16TA-564 5/16-18 31/2 3/8 7/32 11/2 7.31 T-564 6.66TA-381 3/8-16 11/4 7/16 1/4 2 7.88 T-381 7.21TA-382 3/8-16 2 7/16 1/4 2 8.11 T-382 7.45TA-383 3/8-16 23/4 7/16 1/4 2 8.57 T-383 7.97TA-384 3/8-16 31/2 7/16 1/4 2 8.97 T-384 8.41TA-385 3/8-16 41/4 7/16 1/4 2 9.37 T-385 8.85TA-121 1/2-13 2 9/16 5/16 21/2 9.45 T-121 8.85TA-122 1/2-13 23/4 9/16 5/16 21/2 9.79 T-122 9.19TA-123 1/2-13 31/2 9/16 5/16 21/2 10.42 T-123 9.89TA-124 1/2-13 41/4 9/16 5/16 21/2 10.99 T-124 10.51TA-125 1/2-13 5 9/16 5/16 21/2 11.46 T-125 11.01TA-581 5/8-11 21/4 11/16 13/32 3 12.51 T-581 11.95TA-582 5/8-11 3 11/16 13/32 3 12.98 T-582 12.43TA-583 5/8-11 33/4 11/16 13/32 3 13.73 T-583 13.26TA-584 5/8-11 41/2 11/16 13/32 3 14.35 T-584 13.91TA-585 5/8-11 51/4 11/16 13/32 3 15.03 T-585 14.65
Retaining Springs for Toggle Shoe Clamp Assemblies
Cat. No. For Thread Size Price EachTA-98001 1/4 .34TA-98002 5/16 .34TA-98003 3/8 .34TA-98004 1/2 .34TA-98005 5/8 .34
Knurled Head or Socket Head
Toggle shoes are not included with these styles. Toggle shoesare sold separately below.
AKnurled Head Socket Head
KnurledHeadCat. No.
SocketHeadCat.No.
KnurledHeadDia.
Price Each 1-99Thread A OAL Hex Knurled Socket
T-1411 T-1410 1/4-20 13/8 113/16 1/8 11/16 4.11 2.82T-1421 T-1420 1/4-20 21/8 29/16 1/8 11/16 4.17 2.93T-1431 T-1430 1/4-20 27/8 35/16 1/8 11/16 4.41 3.10T-1441 T-1440 1/4-20 35/8 41/16 1/8 11/16 4.61 3.52T-5611 T-5610 5/16-18 15/8 21/8 5/32 3/4 4.48 3.06T-5621 T-5620 5/16-18 23/8 27/8 5/32 3/4 4.61 3.17T-5631 T-5630 5/16-18 31/8 35/8 5/32 3/4 4.85 3.54T-5641 T-5640 5/16-18 37/8 43/8 5/32 3/4 5.31 3.95T-3811 T-3810 3/8-16 13/4 21/4 3/16 7/8 4.80 3.36T-3821 T-3820 3/8-16 21/2 3 3/16 7/8 5.02 3.63T-3831 T-3830 3/8-16 31/4 33/4 3/16 7/8 5.48 4.11T-3841 T-3840 3/8-16 4 41/2 3/16 7/8 6.22 4.61T-3851 T-3850 3/8-16 43/4 51/4 3/16 7/8 6.60 5.02T-1211 T-1210 1/2-13 21/2 31/8 1/4 1 5.85 4.24T-1221 T-1220 1/2-13 31/4 37/8 1/4 1 6.46 4.80T-1231 T-1230 1/2-13 4 45/8 1/4 1 7.03 5.29T-1241 T-1240 1/2-13 43/4 53/8 1/4 1 7.58 5.98T-1251 T-1250 1/2-13 51/2 61/8 1/4 1 8.17 6.46— T-5810 5/8-11 23/4 31/2 5/16 11/8 — 5.42T-5821 T-5820 5/8-11 31/2 41/4 5/16 11/8 8.08 6.16— T-5830 5/8-11 41/4 5 5/16 11/8 — 6.84T-5841 T-5840 5/8-11 5 53/4 5/16 11/8 9.70 7.80T-5851 T-5850 5/8-11 53/4 61/2 5/16 11/8 10.20 8.32
Toggle Shoes
Hardened round steel or nylon.Use nylon shoes for clampingsoft materials to preventmarring or scratching.
SteelCat. No.
NylonCat. No.
Usew/ Size
Price Each 1-99Dia. Lgth. Steel Nylon
SR-14 SR-14N 1/4-20 5/16 3/16 1.20 1.18LR-14 LR-14N 1/4-20 5/8 7/32 1.44 1.57SR-56 SR-56N 5/16-18 3/8 7/32 1.27 1.24LR-56 LR-56N 5/16-18 11/16 1/4 1.57 1.64SR-38 SR-38N 3/8-16 7/16 1/4 1.33 1.31LR-38 LR-38N 3/8-16 3/4 9/32 1.64 1.70SR-12 SR-12N 1/2-13 9/16 5/16 1.42 1.40LR-12 LR-12N 1/2-13 7/8 3/8 1.75 1.83SR-58 SR-58N 5/8-11 11/16 13/32 1.62 1.57LR-58 LR-58N 5/8-11 1 7/16 1.92 1.97
0166.qxd 2/17/2010 3:19 PM Page 166
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 167
Clam
ps an
d W
orkh
old
ing
SWIVEL SCREW CLAMP SYSTEMSSwivel screw clamps can be constructed by pairing any of the bodies with any of the pads. All pads swivel 10° from vertical and haveleft hand threads to prevent backout. Clamping screws are made from 12L14 steel with a black oxide finish. Knob on the hand knobstyle is aluminum with the stud press-fitted in. Pads are case hardened, black oxide finish. Bodies and pads must be orderedseparately.
Bodies Only
A
BC
D
A
BC
D
Hand Knob
Socket Head
Knurled Head
Hand KnobCat. No. A B C D
PriceEach
SSC-1121 1/4-20 115/32 3/4 11/8 4.69SSC-1122 1/4-20 131/32 3/4 11/8 5.08SSC-1131 5/16-18 115/32 7/8 11/2 5.52SSC-1133 5/16-18 215/32 7/8 11/2 5.95SSC-1141 3/8-16 17/16 1 2 6.76SSC-1142 3/8-16 115/16 1 2 7.04SSC-1144 3/8-16 215/16 1 2 8.01SSC-1154 1/2-13 215/16 11/2 21/2 8.01SSC-1155 1/2-13 315/16 11/2 21/2 9.04
Socket HeadCat. No. A B C
PriceEach
SSC-1221 1/4-20 15/32 3/32 2.49SSC-1222 1/4-20 23/32 3/32 2.49SSC-1223 1/4-20 31/32 3/32 2.49SSC-1224 1/4-20 115/32 3/32 2.70SSC-1231 5/16-18 23/32 5/32 2.70SSC-1232 5/16-18 31/32 5/32 2.70SSC-1233 5/16-18 115/32 5/32 2.98SSC-1234 5/16-18 131/32 5/32 2.98SSC-1242 3/8-16 15/16 3/16 3.09SSC-1243 3/8-16 17/16 3/16 3.20SSC-1244 3/8-16 115/16 3/16 3.42SSC-1253 1/2-13 17/16 1/4 4.25SSC-1255 1/2-13 215/16 1/4 4.25
Knurled HeadCat. No. A B C D
PriceEach
SSC-1321 1/4-20 115/32 5/16 1 4.30SSC-1322 1/4-20 131/32 5/16 1 4.37SSC-1331 5/16-18 115/32 3/8 11/8 4.37SSC-1332 5/16-18 131/32 3/8 11/8 4.63SSC-1333 5/16-18 215/32 3/8 11/8 4.86SSC-1341 3/8-16 17/16 7/16 11/4 4.86SSC-1342 3/8-16 115/16 7/16 11/4 4.97SSC-1343 3/8-16 27/16 7/16 11/4 5.13SSC-1344 3/8-16 215/16 7/16 11/4 5.25SSC-1354 1/2-13 215/16 7/16 11/4 5.68
A
B
C HEX
Pads Only
B
D
A
CA
B
CSmall Pad Large Pad
Fits BodyThread Size
Internal ThreadLft. Hand
Small PadCat. No. Price Each
Large PadCat. No. Price EachA B C A B C D
1/4-20 8-36 SSC-1501 .193 3/16 1/16 1.01 SSC-1601 5/16 3/8 1/8 1/8 1.035/16-18 12-28 SSC-1502 19/64 1/4 3/64 1.16 SSC-1602 23/64 1/2 9/64 5/32 1.163/8-16 1/4-28 SSC-1503 21/64 19/64 1/16 1.36 SSC-1603 7/16 9/16 11/64 3/16 1.361/2-13 5/16-24 SSC-1504 25/64 13/32 1/16 1.56 SSC-1604 27/64 3/4 1/8 3/16 1.56
QUICK ACTING KNOBS AND INSERTSQuick Acting Knobs - Inch and Metric
For faster clamping. Tilt knob and it will slide in or out. Straightenknob and threads will engage for clamping. Many tooling applica-tions. Made from powdered metal.
A
DC
B
Fixture
Work
Fixture
Work
ThreadSIze
Price EachCat. No. A B C D 1-11InchQK-1 1/4-20 11/8 9/16 5/8 5/16 4.11QK-2 5/16-18 11/2 11/16 7/8 1/2 4.80QK-3 3/8-16 2 13/16 1 1/2 5.48QK-4 1/2-13 21/2 1 11/8 9/16 6.73QK-5 5/8-11 3 11/4 11/4 5/8 8.45QK-6 3/4-10 3 11/4 11/4 5/8 15.55MetricQK-20 M6x1 11/8 9/16 5/8 5/16 6.03QK-25 M8x1.25 11/2 11/16 7/8 1/2 7.56QK-30 M10x1.5 2 13/16 1 1/2 8.08QK-35 M12x1.75 21/2 1 11/8 9/16 8.45QK-40 M16x2.00 3 11/4 11/4 5/8 8.69
Quick Acting Inserts
Heat treated steel. Black oxide finish. Easily installed in fixture bysimply drilling and tapping hole at required location. For quickaction tilt screw and it will slide in or out. Straighten screw andthreads engage for clamping. See clamp assemblies above foruse with these quick acting inserts.
Work
FixtureInsertLocking Nut
QuickActingInsert
BA
C
D
Price EachCat. No. A B C D 1-11QA-1 1/4-20 1/2-20 1/2 17/64 4.30QA-2 5/16-18 5/8-18 5/8 21/64 4.61QA-3 3/8-16 3/4-16 3/4 25/64 5.31QA-4 1/2-13 1-14 1 33/64 6.73QA-5 5/8-11 11/4-12 11/4 41/64 8.45
Insert Locking Nuts
Used for locking quick actinginserts in position. Heat treatedsteel. Black oxide finish.
ThreadSize
HexSize
Price EachCat. No. Thickness 1-11QN-1 1/2-20 3/4 3/16 1.09QN-2 5/8-18 11/16 1/4 1.49QN-3 3/4-16 11/8 5/16 1.81QN-4 1-14 11/2 3/8 2.82QN-5 11/4-12 13/4 7/16 3.43
0167.qxd 2/17/2010 3:20 PM Page 167
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!168
Cla
mp
s an
d W
ork
ho
ldin
gGRIPPERS
Square EdgeSteel
Items RGHS-20 through RGHS-34 are counterbored for a sockethead cap screw and RGHS-35 through RGHS-53 are counter-bored for a low head socket cap screw.
Discount 14 applies.
A
B
D
C x Depth
Cat. No. A BC’Bore for x Depth
CChamfer
DTooth
PatternPrice Each
1-24RGHS-20 3/8 1/4 #6 x .146 1/16 x 45° Ex-Fine 8.96RGHS-21 3/8 1/4 #6 x .146 1/16 x 45° Super-Fine 9.28RGHS-22 3/8 3/8 #6 x .146 1/16 x 45° Ex-Fine 9.19RGHS-23 3/8 3/8 #6 x .146 1/16 x 45° Super-Fine 9.36RGHS-26 1/2 1/4 #8 x .170 3/32 x 45° Fine 10.74RGHS-27 1/2 1/4 #8 x .170 3/32 x 45° Ex-Fine 10.74RGHS-28 1/2 1/4 #8 x .170 3/32 x 45° Super-Fine 11.06RGHS-29 1/2 3/8 #8 x .175 3/32 x 45° Fine 11.00RGHS-30 1/2 3/8 #8 x .175 3/32 x 45° Ex-Fine 11.00RGHS-31 1/2 3/8 #8 x .175 3/32 x 45° Super-Fine 11.30RGHS-32 1/2 1/2 #8 x .175 3/32 x 45° Fine 11.26RGHS-33 1/2 1/2 #8 x .175 3/32 x 45° Ex-Fine 11.26RGHS-35 5/8 1/4 1/4 x .130 1/8 x 45° Fine 13.55RGHS-36 5/8 1/4 1/4 x .130 1/8 x 45° Ex-Fine 13.55RGHS-37 5/8 3/8 1/4 x .130 1/8 x 45° Fine 13.81RGHS-38 5/8 3/8 1/4 x .130 1/8 x 45° Ex-Fine 13.81RGHS-39 5/8 1/2 1/4 x .130 1/8 x 45° Fine 14.06RGHS-40 5/8 1/2 1/4 x .130 1/8 x 45° Ex-Fine 14.06RGHS-42 3/4 1/4 5/16 x .161 1/8 x 45° Fine 15.21RGHS-44 3/4 3/8 5/16 x .161 1/8 x 45° Fine 15.49RGHS-46 3/4 1/2 5/16 x .161 1/8 x 45° Fine 15.72RGHS-47 3/4 1/2 5/16 x .161 1/8 x 45° Ex-Fine 15.72RGHS-48 1 1/4 3/8 x .194 1/8 x 45° Fine 20.51RGHS-50 1 3/8 3/8 x .194 1/8 x 45° Fine 20.77RGHS-52 1 1/2 3/8 x .194 1/8 x 45° Fine 21.02RGHS-53 1 1/2 3/8 x .194 1/8 x 45° Ex-Fine 21.02
REST PADSSolid CarbideRound, Square and Rectangle
B
A C
A
A B
Discount 14 applies.
A
BRound Square Rectangle
Cat. No.
+.000/-.005
A
+.005/-.000
BTooth
Pattern
PriceEach1-24 Cat. No.
+.000/-.005
A
+.005/-.000
B CTooth
Pattern
PriceEach1-24
Round SquareRGCP-1 1/4 1/8 Ex-Fine 5.68 RGCP-9 1/2 1/8 — Fine 8.28RGCP-2 5/16 1/8 Ex-Fine 5.13 RGCP-1227 1/2 1/8 — Ex-Fine 8.28RGCP-1207 5/16 1/8 4 Point 5.83 RGCP-1229 5/8 1/8 — Ex-Fine 10.53RGCP-3 3/8 1/8 Fine 5.13 RGCP-11 3/4 5/32 — Ex-Fine 13.51RGCP-1211 3/8 1/8 Ex-Fine 5.13 RGCP-12 1 5/32 — Ex-Fine 20.00RGCP-1213 3/8 1/8 4 Point 5.13 RectangleRGCP-13 3/8 1/8 Flat 5.13 RGCP-1231 3/8 1/4 1/8 Ex-Fine 5.83RGCP-4 7/16 1/8 Fine 6.32 RGCP-1233 1/2 13/32 1/8 Fine 7.87RGCP-5 1/2 1/8 Fine 5.89 RGCP-1239 29/64 13/32 1/8 Fine 5.83RGCP-1215 1/2 1/8 Ex-Fine 5.89 RGCP-1245 1 1/2 3/16 Sawtooth 10.96RGCP-6 5/8 1/8 Fine 7.19 RGCP-1247 1 1/2 3/16 Ex-Fine 10.96RGCP-7 3/4 1/8 Fine 10.28 RGCP-1249 11/2 3/4 1/4 Sawtooth 21.06RGCP-1223 3/4 1/8 Ex-Fine 10.28RGCP-8 1 5/32 Ex-Fine 20.00
Tapped Hole Design
These tapped hole rest pads can be used with the swivel actionball units shown on page 169.
Steel and Delrin
Discount 14 applies.
A
C TAP
B
DTAP DEPTH
SteelCat. No.
DelrinCat. No.
Price Each 1-24A B C D Steel Delrin
RRP-2S RRP-2D 3/8 3/8 10-32 3/16 5.06 4.70RRP-4S RRP-4D 3/8 1/2 10-32 5/16 5.15 4.77RRP-6S — 1/2 3/8 10-32 3/16 5.36 —RRP-8S — 1/2 1/2 10-32 5/16 5.43 —RRP-10S RRP-10D 5/8 3/8 1/4-28 3/16 5.79 5.51RRP-12S — 5/8 1/2 1/4-28 5/16 5.85 —RRP-14S — 3/4 3/8 1/4-28 3/16 6.38 —RRP-16S — 3/4 1/2 1/4-28 5/16 6.45 —RRP-18S — 1 3/8 1/4-28 3/16 6.74 —RRP-20S RRP-20D 1 1/2 1/4-28 5/16 6.83 6.53
Carbide Tipped
Discount 14 applies.
EA
F TAP
B
.03
DC
CarbideTippedCat. No. A
+/- .001B C D E F
Price Each1-24
RRP-22 3/8 3/8 11/64 3/16 5/16 10-32 9.94RRP-24 3/8 1/2 15/64 3/16 5/16 10-32 10.11RRP-26 1/2 3/8 11/64 3/16 3/8 10-32 10.11RRP-28 1/2 1/2 15/64 3/16 3/8 10-32 10.23RRP-30 5/8 3/8 11/64 3/16 1/2 1/4-28 10.68RRP-36 3/4 1/2 15/64 3/16 5/8 1/4-28 12.57RRP-38 1 3/8 11/64 3/16 3/4 1/4-28 20.40
Whether you need to
Count on Reid to help you keep it all together.
Reid Has Your Workholding Supplies
Grip it,
Hold it,
Clamp it.
0168.qxd 2/22/2010 9:28 AM Page 168
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 169
Clam
ps an
d W
orkh
old
ing
SWIVEL ACTION GRIPPERS
Note: Swivel action grippers are self aligning (minimum 10°) to regularity of the work piece.
Ball Units
Hex Head Ball Unit
Consists of stainless steel ball with pocket area to accept areplaceable gripper and a socket head cap screw to hold thegripper in place. Ball is retained in the hex head housing by anO-ring that facilitates swiveling action and keeps contaminantsout. Housing is heat treated alloy steel. Grippers are notincluded in assembly and must be purchased separately.Any round style gripper or rest pad with a tapped hole can beused (carbide tipped, high speed steel, solid carbide or Delrin).See "D" dimension for gripper diameter to use. See pages 168and 170 for grippers and rest pads.
Discount 14 applies.
C - HEX
D GRIPPER DIA.
B A
E THREADF HEX SOC
REPLACEABLE PAD(MUST BE PURCHASED SEPARATELY)
1/8
+/-.005B
BallDia.
Price Each1-24Cat. No. A C D E F
RGBU-200 1/2 5/8 5/8 3/8 3/8-24 1/8 1/2 46.55RGBU-205 1 5/8 5/8 3/8 3/8-24 1/8 1/2 47.28RGBU-210 11/2 5/8 5/8 3/8 3/8-24 1/8 1/2 48.32RGBU-215 1/2 5/8 5/8 3/8 3/8-16 1/8 1/2 46.55RGBU-220 1 5/8 5/8 3/8 3/8-16 1/8 1/2 47.28RGBU-225 11/2 5/8 5/8 3/8 3/8-16 1/8 1/2 48.32RGBU-230 1 3/4 13/16 1/2 1/2-20 3/16 5/8 50.43RGBU-235 11/2 3/4 13/16 1/2 1/2-20 3/16 5/8 51.49RGBU-240 1 3/4 13/16 1/2 1/2-13 3/16 5/8 50.43RGBU-245 11/2 3/4 13/16 1/2 1/2-13 3/16 5/8 51.49RGBU-255 2 13/16 15/16 5/8 5/8-18 1/4 3/4 54.32RGBU-260 1 13/16 15/16 5/8 5/8-11 1/4 3/4 52.55RGBU-265 2 13/16 15/16 5/8 5/8-11 1/4 3/4 54.32RGBU-270 1 7/8 11/8 3/4 3/4-16 5/16 7/8 56.79RGBU-275 21/2 7/8 11/8 3/4 3/4-16 5/16 7/8 58.55RGBU-280 1 7/8 11/8 3/4 3/4-10 5/16 7/8 56.79RGBU-285 21/2 7/8 11/8 3/4 3/4-10 5/16 7/8 58.55RGBU-1307 4 1 11/2 1 1-14 3/8 11/8 69.74RGBU-1309 2 1 11/2 1 1-8 3/8 11/8 67.23RGBU-1311 4 1 11/2 1 1-8 3/8 11/8 69.74
Base Ball Unit
Discount 14 applies.+/-.005
B+/-.010
EBallDia.
Price Each1-24Cat. No. A C D F
RGBU-300 5/8 7/8 3/4 3/8 .24 1/4-28 1/2 37.66RGBU-305 13/16 1 7/8 1/2 .35 5/16-24 5/8 41.43RGBU-310 15/16 1 7/8 5/8 .28 3/8-24 3/4 44.17RGBU-315 11/8 11/16 15/16 3/4 .26 1/2-20 7/8 49.72RGBU-1315 11/2 13/8 11/4 1 .44 1/2-20 11/8 59.98
Threaded Ball Unit
Discount 14 applies.BallDia.
Price EachCat. No. A B C D 1-24RGBU-410 1 3/4-10 3/8 3/8 1/2 39.04RGBU-415 2 3/4-10 3/8 3/8 1/2 40.06RGBU-1322 3 3/4-10 3/8 3/8 1/2 42.32RGBU-1324 2 1-14 3/8 5/8 3/4 48.32RGBU-1326 3 1-14 3/8 5/8 3/4 49.72
Ball Assemblies
Hex Head Ball Assemblies
These assemblies are similar to the ball units, however, the padand ball are one unit and included with the assemblies. The padsare available in high speed steel, (serrated or flat) and delrin (flatonly). The ball is replaceable and available as a special order.Please call for price and delivery.
Discount 14 applies.
Serrated Flat
Base Ball Assemblies
Discount 14 applies.
Serrated Flat
Cat. No. Type A+/-.005
B+/-.010
C D EPrice Each
1-24RGBA-44S Serrated 1/2 9/16 5/32 5/16 10-32 30.13RGBA-44F Flat 1/2 9/16 5/32 5/16 10-32 28.06RGBA-46S Serrated 1/2 11/16 5/8 5/16 10-32 31.51
Threaded Ball Assemblies
Discount 14 applies.
Cat. No. Type A B C DPrice Each
1-24RGBA-50S Serrated 3/8-24 1/2 3/16 5/32 27.19RGBA-52S Serrated 3/8-24 1 3/16 5/32 27.45RGBA-54S Serrated 3/8-24 2 3/16 5/32 27.94RGBA-60S Serrated 3/8-16 1 3/16 5/32 27.45RGBA-62S Serrated 3/8-16 2 3/16 5/32 27.94RGBA-64S Serrated 3/8-16 3 3/16 5/32 29.13RGBA-66S Serrated 1/2-20 1 1/4 1/4 28.96RGBA-70S Serrated 1/2-20 3 1/4 1/4 32.11RGBA-72S Serrated 1/2-13 1 1/4 1/4 28.96RGBA-74S Serrated 1/2-13 2 1/4 1/4 29.57RGBA-76S Serrated 1/2-13 3 1/4 1/4 31.17RGBA-78S Serrated 5/8-18 1 5/16 5/16 32.19RGBA-86S Serrated 5/8-11 2 5/16 5/16 32.87
Cat. No. Type A+/-.005
B C D EPrice Each
1-24RGBA-6S Serrated 3/8 5/16 1/2 5/32 10-32 30.83RGBA-10S Serrated 7/16 3/8 1/2 1/4 1/4-20 32.68RGBA-12S Serrated 7/16 3/8 1 1/4 1/4-20 33.28RGBA-14S Serrated 7/16 3/8 11/2 1/4 1/4-20 33.89RGBA-16S Serrated 7/16 3/8 1/2 1/4 1/4-28 32.68RGBA-22S Serrated 1/2 7/16 1/2 5/16 5/16-18 36.30RGBA-24S Serrated 1/2 7/16 1 5/16 5/16-18 36.98RGBA-26S Serrated 1/2 7/16 11/2 5/16 5/16-18 37.66RGBA-28S Serrated 1/2 7/16 1/2 5/16 5/16-24 36.30RGBA-10F Flat 7/16 3/8 1/2 1/4 1/4-20 30.83RGBA-22F Flat 1/2 7/16 1/2 5/16 5/16-18 34.23RGBA-24F Flat 1/2 7/16 1 5/16 5/16-18 34.94RGBA-30F Flat 1/2 7/16 1 5/16 5/16-24 34.94RGBA-26D Delrin 1/2 7/16 11/2 5/16 5/16-18 34.57
0169.qxd 2/23/2010 12:53 PM Page 169
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!170
Cla
mp
s an
d W
ork
ho
ldin
gGRIPPERS
Eliminates costly maintenance and chuck jaw replacement. After long periods of maintenance-free serviceFairlane inserts can be quickly replaced at low cost. Replacement can be accomplished right at themachine without costly downtime. Applicable to most chuck jaw designs. Held in place either by beingthreaded (to be held by screws entered through jaw), or flat on side to be held by set screw pressure. Steeltype are made from hardened tool steel.
SteelRound B
.03 X 45¡
A
DTap
EC
.03A
.130
DTap
B
.06
Discount 14 applies.
DTAP BLIND
COR. BREAK
A .188B
w/Keyway
+.000/-.005
A
+.000/-.005
B
ThruHole
DCat. No. C ETooth
PatternPrice Each
1-24RGHS-00 1/4 3/8 — 8-32 — Ex-Fine 7.68RGHS-0 3/8 3/8 11/64 10-32 3/16 Ex-Fine 7.55RGHS-210 3/8 1/2 15/64 10-32 3/16 Ex-Fine 7.83RGHS-1 1/2 3/8 11/64 10-32 3/16 Fine 7.89RGHS-215 1/2 3/8 11/64 10-32 3/16 Ex-Fine 7.89RGHS-220 1/2 1/2 15/64 10-32 3/16 Coarse 8.17RGHS-225 1/2 1/2 Keyway 10-32 — Fine 8.38RGHS-2 1/2 1/2 15/64 10-32 3/16 Fine 8.17RGHS-235 1/2 1/2 15/64 10-32 3/16 Ex-Fine 8.17RGHS-240 1/2 .651 19/64 10-32 3/16 Fine 8.17RGHS-3 5/8 3/8 11/64 1/4-28 3/16 Fine 10.77RGHS-250 5/8 3/8 11/64 1/4-28 3/16 Ex-Fine 10.77RGHS-260 5/8 3/8 11/64 1/4-28 3/16 Coarse 10.77RGHS-265 5/8 1/2 15/64 1/4-28 3/16 Fine 11.02RGHS-275 5/8 1/2 15/64 1/4-28 3/16 Coarse 11.02RGHS-4 3/4 3/8 11/64 1/4-28 3/16 Fine 11.87RGHS-285 3/4 3/8 11/64 1/4-28 3/16 Ex-Fine 11.87RGHS-290 3/4 3/8 11/64 1/4-28 3/16 Coarse 11.87RGHS-295 3/4 1/2 15/64 1/4-28 3/16 Fine 12.30RGHS-300 3/4 1/2 15/64 1/4-28 3/16 Ex-Fine 12.30RGHS-305 3/4 1/2 15/64 1/4-28 3/16 Coarse 12.30RGHS-315 1 3/8 11/64 1/4-28 3/16 Coarse 14.38RGHS-41 1 3/8 11/64 1/4-28 3/16 Fine 14.38RGHS-330 1 3/8 11/64 1/4-28 3/16 Ex-Fine 14.38RGHS-335 1 1/2 15/64 1/4-28 3/16 Coarse 14.81RGHS-345 1 1/2 15/64 1/4-28 3/16 Fine 14.81RGHS-350 1 1/2 15/64 1/4-28 3/16 Ex-Fine 14.81
SteelSquare
Discount 14 applies.
A
A
B
DTap
+.000/-.005
A
+.000/-.005
B
PriceEach1-24
+.000/-.005
A
+.000/-.005
B
PriceEach1-24Cat. No.
DTap
ToothPattern Cat. No.
DTap
ToothPattern
RGHS-360 3/8 3/8 10-32 Ex-Fine 8.32 RGHS-400 3/4 3/8 10-32 Coarse 14.38RGHS-5 1/2 3/8 10-32 Fine 10.40 RGHS-405 3/4 1/2 10-32 Fine 15.02RGHS-370 1/2 3/8 10-32 Ex-Fine 10.40 RGHS-410 3/4 1/2 10-32 Ex-Fine 15.02RGHS-375 1/2 1/2 10-32 Fine 10.62 RGHS-415 3/4 1/2 10-32 Coarse 15.02RGHS-380 1/2 1/2 10-32 Ex-Fine 10.62 RGHS-7 1 3/8 1/4-28 Fine 20.11RGHS-385 1/2 3/8 10-32 Coarse 10.40 RGHS-420 1 3/8 1/4-28 Ex-Fine 20.11RGHS-390 1/2 1/2 10-32 Coarse 10.62 RGHS-425 1 3/8 1/4-28 Coarse 20.11RGHS-6 3/4 3/8 10-32 Fine 14.38 RGHS-430 1 1/2 1/4-28 Fine 20.66RGHS-395 3/4 3/8 10-32 Ex-Fine 14.38
SteelAngle Grip
For use on N.A. Woodworth ball lock chuck.
Discount 14 applies.
A
.65+.000-.010
C TapB
.60
+.000/-.002
A
+.000/-.005
B
PriceEach1-24
+.000/-.002
A
+.000/-.005
B
PriceEach1-24Cat. No.
CTap
ToothPattern Cat. No.
CTap
ToothPattern
RGHS-127-4 .562 .375 10-32 4 Point 10.11 RGHS-560 .562 .375 10-32 Angular 11.30RGHS-127-12 .562 .375 10-32 Fine 10.11 RGHS-128-4 .750 .500 1/4-28 4 Point 20.96
Solid CarbideRound and Square
Discount 14 applies.+.000/-.005
A
+.000/-.005
BCat. No.TapC D E F
ToothPattern
Price Each1-24
RoundRGSC-1 1/2 3/8 11/64 10-32 3/16 3/16 Fine 15.13RGSC-1270 1/2 1/2 15/64 10-32 3/16 5/16 4 Point 16.74RGSC-2 1/2 1/2 15/64 10-32 3/16 5/16 Fine 16.74RGSC-3 5/8 3/8 11/64 1/4-28 3/16 3/16 Fine 21.77RGSC-4 3/4 3/8 11/64 1/4-28 3/16 3/16 Fine 26.83SquareRGSC-5 1/2 3/8 — 10-32 — 3/16 Fine 20.74RGSC-6 1/2 1/2 — 10-32 — 5/16 Fine 21.94
Carbide TippedRound
.130EA
FTap
B
.06
Discount 14 applies.
EA
FTap
BDC
.03
w/ Keyway
+.000/-.005
A
+.000/-.005
B
Blind HoleTapFCat. No. C D E
ToothPattern
Price Each1-24
RG-0 3/8 3/8 11/64 3/16 5/16 10-32 Ex-Fine 8.09RG-200 3/8 1/2 15/64 3/16 5/16 10-32 Ex-Fine 8.21RG-2 1/2 1/2 15/64 3/16 3/8 10-32 Fine 8.06RG-202 1/2 1/2 15/64 3/16 3/8 10-32 Ex-Fine 8.06RG-204 1/2 1/2 15/64 3/16 3/8 10-32 4 Point 8.06RG-1 1/2 3/8 11/64 3/16 3/8 10-32 Fine 7.70RG-230 1/2 3/8 11/64 3/16 3/8 10-32 Ex-Fine 7.70RG-206 1/2 3/8 11/64 3/16 3/8 10-32 4 Point 7.70RG-208 1/2 .651 19/64 3/16 3/8 10-32 Fine 8.06RG-210 1/2 .651 19/64 3/16 3/8 10-32 Ex-Fine 8.06RG-3 5/8 3/8 11/64 3/16 1/2 1/4-28 Fine 9.30RG-234 5/8 3/8 11/64 3/16 1/2 1/4-28 Ex-Fine 9.30RG-218 5/8 1/2 15/64 3/16 1/2 1/4-28 Fine 10.11RG-224 5/8 5/8 Keyway — 1/2 1/4-28 Fine 14.74RG-4 3/4 3/8 11/64 3/16 5/8 1/4-28 Fine 10.96RG-236 3/4 3/8 11/64 3/16 5/8 1/4-28 Ex-Fine 10.96RG-222 3/4 1/2 15/64 3/16 5/8 1/4-28 Fine 11.77RG-238 3/4 1/2 15/64 3/16 5/8 1/4-28 Ex-Fine 11.77RG-41 1 3/8 11/64 3/16 3/4 1/4-28 Fine 18.49RG-240 1 3/8 11/64 3/16 3/4 1/4-28 Ex-Fine 18.49
Carbide TippedSquare
Discount 14 applies.
EA
A
FTap
B
+.000/-.005
A
+.000/-.005
B
Blind HoleTapFCat. No. E
ToothPattern
Price Each1-24
RG-5 1/2 3/8 13/32 10-32 Fine 11.21RG-250 1/2 3/8 13/32 10-32 Ex-Fine 11.21RG-255 1/2 1/2 13/32 10-32 Fine 12.09
Carbide TippedAngle Grip
Discount 14 applies.
A
.65+.000-.010
D
C TapB
.60
Blind Hole Tap
CCat. No.+.000/-.005
A+.000/-.005
B D Tooth PatternPrice Each
1-24RG-270 .562 .375 10-32 15/32 4 Point 9.38RG-275 .562 .375 10-32 15/32 Fine 9.38
SteelRound and Squarew/ Counterbore
*Socket head cap screw
Discount 14 applies.
BA
A
+.000/-.005
A
+.000/-.005
B
PriceEach1-24
+.000/-.005
A
+.000/-.005
B
PriceEach1-24Cat. No.
C’Bore*to Fit
ToothPattern Cat. No.
C’Bore*to Fit
ToothPattern
RoundRGHS-2405 1/2 3/8 #8 Fine 8.09 RGHS-2475 1 1/2 1/4 Coarse 15.36RGHS-2410 1/2 3/8 #8 Ex-Fine 8.09 RGHS-81 1 1/2 1/4 Fine 15.36RGHS-2415 1/2 1/2 #8 Fine 8.43 RGHS-2480 1 1/2 1/4 Ex-Fine 15.36RGHS-2420 1/2 1/2 #8 Ex-Fine 8.43 SquareRGHS-2425 5/8 3/8 #8 Fine 11.09 RGHS-2485 1/2 3/8 #10 Fine 10.77RGHS-2430 5/8 3/8 #8 Ex-Fine 11.09 RGHS-2490 1/2 3/8 #10 Ex-Fine 10.77RGHS-2435 5/8 1/2 #8 Fine 11.38 RGHS-2495 1/2 1/2 #10 Fine 11.02RGHS-2440 5/8 1/2 #8 Ex-Fine 11.38 RGHS-82 3/4 1/2 1/4 Fine 15.36RGHS-2445 3/4 3/8 #10 Fine 12.43 RGHS-2505 3/4 1/2 1/4 Ex-Fine 15.36RGHS-80 3/4 1/2 #10 Fine 12.77 RGHS-2510 3/4 1/2 1/4 Coarse 15.36RGHS-2455 3/4 1/2 #10 Ex-Fine 12.77 RGHS-83 1 1/2 1/4 Fine 20.66RGHS-2460 3/4 3/8 #10 Coarse 12.43 RGHS-2515 1 1/2 1/4 Ex-Fine 20.66RGHS-2470 3/4 1/2 #10 Coarse 12.77 RGHS-2520 1 1/2 1/4 Coarse 20.66
0170.qxd 2/17/2010 3:21 PM Page 170
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 171
Clam
ps an
d W
orkh
old
ing
PriceEach1-24
ToothPatternHexDCBACat. No.
GRIPPERSEliminates costly maintenance and chuck jaw replacement. After long periods of maintenance-free service,Fairlane inserts can be quickly replaced at low cost. Replacement can be accomplished right at the machine,without costly downtime. Applicable to most chuck jaw designs. Held in place either by being threaded (to beheld by screws entered through jaw), or flat on side to be held by set screw pressure. Steel type are madefrom hardened tool steel.
Carbide TippedAdjustable
Discount 14 applies.
B
AD
C Hex
Socket Type
Cat. No. A B C D HexTooth
Pattern
PriceEach1-24
Socket TypeRG-1000 1/2 1/4 3/8-24 .05 3/16 Ex-Fine 12.85RG-1002 1 1/4 3/8-24 .05 3/16 Ex-Fine 13.00RG-1004 11/2 1/4 3/8-24 .05 3/16 Ex-Fine 13.13RG-1006 2 1/4 3/8-24 .05 3/16 Ex-Fine 13.28RG-1010 1/2 1/4 3/8-16 .05 3/16 Ex-Fine 12.85RG-30 1 1/4 3/8-16 .05 3/16 Ex-Fine 13.00RG-1012 2 1/4 3/8-16 .05 3/16 Ex-Fine 13.28RG-1014 3 1/4 3/8-16 .05 3/16 Ex-Fine 13.70RG-1016 1 3/8 1/2-20 .05 1/4 Fine 12.00RG-1018 1 3/8 1/2-20 .05 1/4 Ex-Fine 12.00RG-1020 1 3/8 1/2-20 .07 1/4 4 Point 12.00RG-1022 2 3/8 1/2-20 .05 1/4 Fine 12.43RG-1024 2 3/8 1/2-20 .05 1/4 Ex-Fine 12.43RG-1026 2 3/8 1/2-20 .07 1/4 4 Point 12.43RG-1028 3 3/8 1/2-20 .05 1/4 Fine 12.85RG-31 1 3/8 1/2-13 .05 1/4 Fine 12.00RG-1034 1 3/8 1/2-13 .05 1/4 Ex-Fine 12.00RG-1036 1 3/8 1/2-13 .07 1/4 4 Point 12.00RG-32 2 3/8 1/2-13 .05 1/4 Fine 12.43RG-1038 2 3/8 1/2-13 .05 1/4 Ex-Fine 12.43RG-1040 2 3/8 1/2-13 .07 1/4 4 Point 12.43RG-1042 3 3/8 1/2-13 .05 1/4 Fine 12.85RG-1044 3 3/8 1/2-13 .05 1/4 Ex-Fine 12.85RG-1048 1 1/2 5/8-18 .05 5/16 Fine 13.13RG-33 1 7/16 5/8-11 .05 5/16 Fine 13.13RG-34 2 7/16 5/8-11 .05 5/16 Fine 13.64RG-1080 3 7/16 5/8-11 .05 5/16 Fine 14.11RG-1086 1 1/2 3/4-16 .05 3/8 Fine 14.26RG-1092 2 1/2 3/4-16 .05 3/8 Fine 14.66RG-35 1 1/2 3/4-10 .05 3/8 Fine 14.26RG-1104 1 1/2 3/4-10 .05 3/8 Ex-Fine 14.26
Discount 14 applies.
C
D
B A
E
Hex Type
Discount 14 applies.
DC
Flats F
BA
Hex
E
Wrench Flats Type
Cat. No. A B C D E F HexTooth
Pattern
PriceEach1-24
Wrench Flats TypeRG-750 .937 9/16 .500 3/8 3/8-24 .15 1/8 Fine 16.77RG-752 .937 9/16 .500 3/8 3/8-24 .15 1/8 Ex-Fine 16.77RG-754 1.375 1 .500 3/8 3/8-24 .15 1/8 Fine 17.11RG-756 1.375 1 .500 3/8 3/8-24 .15 1/8 Ex-Fine 17.32RG-770 .937 9/16 .500 3/8 3/8-16 .15 1/8 Fine 16.77RG-100 1.375 1 .500 3/8 3/8-16 .15 1/8 Fine 17.11RG-776 1.875 11/2 .500 3/8 3/8-16 .15 1/8 Fine 17.32RG-780 1.375 7/8 .625 1/2 1/2-20 .25 3/16 Fine 17.11RG-784 2.062 11/2 .625 1/2 1/2-20 .25 3/16 Fine 17.47RG-101 1.375 7/8 .625 1/2 1/2-13 .25 3/16 Fine 17.11RG-796 2.562 2 .750 5/8 5/8-18 .25 1/4 Fine 17.83RG-102 2.062 11/2 .625 1/2 1/2-13 25 3/16 Fine 17.47RG-800 1.562 1 .750 5/8 5/8-11 .25 1/4 Fine 17.47RG-103 2.562 2 .750 5/8 5/8-11 .25 1/4 Fine 17.83RG-804 2.562 2 .750 5/8 5/8-11 .25 1/4 Ex-Fine 17.83RG-814 1.562 1 .875 3/4 3/4-10 .25 5/16 Fine 19.21RG-818 3.062 21/2 .875 3/4 3/4-10 .25 5/16 Fine 19.57
Cat. No. A B C D HexTooth
Pattern
PriceEach1-24
Hex TypeRG-825 1/2 13/64 7/16 5/16 1/4-20 Ex-Fine 6.98RG-20 1 13/64 7/16 5/16 1/4-20 Ex-Fine 7.13RG-827 11/2 13/64 7/16 5/16 1/4-20 Ex-Fine 7.26RG-829 1/2 13/64 7/16 5/16 1/4-28 Ex-Fine 6.98RG-831 1 13/64 7/16 5/16 1/4-28 Ex-Fine 7.13RG-835 1/2 1/4 1/2 3/8 5/16-18 Fine 7.19RG-837 1/2 1/4 1/2 3/8 5/16-18 Ex-Fine 7.19RG-21 1 1/4 1/2 3/8 5/16-18 Fine 7.34RG-839 1 1/4 1/2 3/8 5/16-18 Ex-Fine 7.34RG-841 11/2 1/4 1/2 3/8 5/16-18 Fine 7.47RG-843 11/2 1/4 1/2 3/8 5/16-18 Ex-Fine 7.47RG-845 1/2 1/4 1/2 3/8 5/16-24 Fine 7.19RG-847 1/2 1/4 1/2 3/8 5/16-24 Ex-Fine 7.19RG-849 1 1/4 1/2 3/8 5/16-24 Fine 7.34RG-851 1 1/4 1/2 3/8 5/16-24 Ex-Fine 7.34RG-853 11/2 1/4 1/2 3/8 5/16-24 Fine 7.47RG-857 1/2 9/32 9/16 1/2 3/8-24 Fine 8.23RG-861 1 9/32 9/16 1/2 3/8-24 Fine 8.38RG-863 1 9/32 9/16 1/2 3/8-24 Ex-Fine 8.38RG-865 11/2 9/32 9/16 1/2 3/8-24 Fine 8.66RG-869 1/2 9/32 9/16 1/2 3/8-16 Fine 8.23RG-871 1/2 9/32 9/16 1/2 3/8-16 Ex-Fine 8.23RG-22 1 9/32 9/16 1/2 3/8-16 Fine 8.38RG-873 1 9/32 9/16 1/2 3/8-16 Ex-Fine 8.38RG-23 11/2 9/32 9/16 1/2 3/8-16 Fine 8.66RG-875 11/2 9/32 9/16 1/2 3/8-16 Ex-Fine 8.66RG-877 1 23/64 3/4 5/8 1/2-20 Fine 10.49RG-879 1 23/64 3/4 5/8 1/2-20 Ex-Fine 10.49RG-881 11/2 23/64 3/4 5/8 1/2-20 Fine 10.83RG-24 1 23/64 3/4 5/8 1/2-13 Fine 10.49
Hex Type (continued)RG-885 1 23/64 3/4 5/8 1/2-13 Ex-Fine 10.49RG-25 11/2 23/64 3/4 5/8 1/2-13 Fine 10.83RG-887 11/2 23/64 3/4 5/8 1/2-13 Ex-Fine 10.83RG-889 1 7/16 15/16 3/4 5/8-18 Fine 13.64RG-26 1 7/16 15/16 3/4 5/8-11 Fine 13.64RG-27 2 7/16 15/16 3/4 5/8-11 Fine 13.98RG-901 1 1/2 11/8 1 3/4-16 Ex-Fine 23.04RG-903 21/2 1/2 11/8 1 3/4-16 Ex-Fine 23.74
Steel - Adjustable
Discount 14 applies.
A
B
Hex
PriceEach1-24
PriceEach1-24Cat. No. A B Hex
ToothPattern Cat. No. A B Hex
ToothPattern
RGHS-600 1 3/8-24 1/8 Ex-Fine 11.60 RGHS-91 11/2 1/2-13 3/16 Fine 12.21RGHS-605 11/2 3/8-24 1/8 Ex-Fine 12.21 RGHS-615 11/2 5/8-18 1/4 Fine 13.62RGHS-90 11/2 3/8-16 1/8 Ex-Fine 12.21 RGHS-92 11/2 5/8-11 1/4 Fine 13.62RGHS-610 11/2 1/2-20 3/16 Fine 12.21 RGHS-93 11/2 3/4-10 5/16 Fine 14.66
Adjustagrip™ - Steel
Note: All Adjustagrips™ come with differential screws. Grippers must bepurchased separately. Reference “D” dimension for gripper.
Discount 14 applies.
E
C
H A
Hex
B F TapD Gripper
ThreadB
GripperD*
Price Each1-24Cat. No. A C E F Hex H
RGHS-101 1 1/2-13 .500 RGHS-1 11/16 10-32LH 3/16 .625 16.09RGHS-102 11/2 1/2-13 .500 RGHS-1 11/16 10-32LH 3/16 .625 16.30*See page 170 for grippers
CHUCK JAW GRIPPERSBlind Hole
Simply drill, tap and install. These blind hole grippers make iteasy to modify soft top jaws, strap clamps or fixtures. Gripperscan be installed from one side using a combination center drill,tap and wrench, eliminating the need to drill through holes.Hardened steel grippers are case hardened with black oxidefinish. Carbide tipped grippers have cadmium plated finish.
FineSerrated
Pointed CarbideTipped
Hardened Steel Grippers
Discount 14 applies.
SerratedCat. No.
PointedCat. No.
HexA
ThreadE
CenterDrill
Drillto Dia.
Price Each1-24
B C D Serrated PointedJRG-23801 JRG-23811 5/16 .093 .32 .19 8-32 No. 4 .310 12.10 10.01JRG-23802 JRG-23812 1/2 .125 .46 .25 1/4-28 No. 6 .498 12.44 10.25JRG-23803 JRG-23813 3/4 .187 .70 .38 3/8-16 No. 8 .745 14.06 12.27
Carbide Tipped Grippers
Discount 14 applies.HexA
ThreadE
CenterDrill
Drillto Dia.
Price EachCat. No. B C D 1-24JRG-23822 1/2 .125 .46 .25 1/4-28 No. 6 .498 19.57JRG-23823 3/4 .187 .70 .38 3/8-16 No. 8 .745 23.45
0171.qxd 2/17/2010 3:21 PM Page 171
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!172
Cla
mp
s an
d W
ork
ho
ldin
gINDUSTRIAL VISES
Machinists’ Vises
Built for performance and endurance. Stress parts are 60,000 psi ductile iron. Hardened steeljaw. Replaceable inserts are serrated for safe, sure grip. Straight line design - horizontalspindle and nut eliminate thread wear. Swivel base allows for 360° rotation and has doublelockdowns for non-slip holding and four mounting points.
JawWidth
Max.Opening
ThroatDepth
ShippingWeightCat. No. Description Price Each
WLT-25 4 61/2 31/2 Swivel Base 62 568.00
High Visibility Safety Vise
Coated in high visibility yellow which conforms to OSHA safety color standard. Heavy dutycasting, 30,000 psi. Replaceable hardened steel jaw inserts and replaceable pipe jaws toprovide sure grip for a variety of work holding applications. 360° swivel base.
JawWidth
MaxOpening
PipeCapacity
ShippingWgt. (Lbs.)
PriceEachCat. No.
WLT-110 5 51/4 1/4-21/2 50 224.00WLT-115 6 53/4 1/4-31/2 64 272.00
Combination Pipe and Bench Vises
Built for the toughest applications. 60,000 psi tensile ductile iron body parts for mass andstrength. Replaceable hardened steel jaw inserts. Self centering pipe jaws. Locking swivelbase with double lockdowns for non-slip hold in any position. Enclosed construction keepslubrication in and contaminants out for outdoor use.
JawWidth
MaxOpening
PipeCapacity
ThroatDepth
ShippingWgt. (Lbs.)
PriceEachCat. No.
WLT-130 41/2 6 1/8-31/2 43/4 77 840.00
Tradesman Vise
For general purpose service or maintenance shops not requiring the strength of a combina-tion vise. 60,000 psi ductile iron body parts hardened steel top and pipe jaws. Base swivels.
JawWidth
MaxOpening
Pipe JawCapacity
ThroatDepth
ShippingWgt. (Lbs.)
PriceEachCat. No.
WLT-150 41/2 4 1/4-21/2 31/4 33 376.00WLT-155 51/2 5 1/4-3 33/4 49 456.00WLT-160 61/2 61/2 1/4-31/2 4 70 512.00WLT-165 8 7 1/8-31/2 43/4 105 784.00
Utility Workshop Vise
A versatile all-around vise. Features a formed steel channel beam and a hefty 30,000 psi bodycasting. Replaceable, serrated steel top jaws and built in pipe jaws. 180° locking swivel base.
JawWidth
MaxOpening
ThroatDepth
PipeCapacity
ShippingWgt. (Lbs.)
PriceEachCat. No.
WLT-180 41/2 4 31/2 1/8-2 171/2 80.00WLT-185 51/2 5 4 1/8-21/2 30 104.00WLT-190 61/2 51/2 5 1/8-21/2 40 136.00WLT-195 6 6 6 1/8-3 66 200.00WLT-200 8 71/2 8 1/8-3 80 248.00
Mechanics’ Vise
This vise has a swivel base that rotates 365° with double lockdowns ensuing maximumstability. The powder coat paint resists scratches and provides a tough, durable finish. It alsofeatures replaceable hardened steel top and pipe jaws and a large anvil work surface.
JawWidth
JawOpening
ThroatDepth
PipeCapacity
PriceEachCat. No.
WLT-746 6 53/4 41/8 1/4-31/2 272.00
0172.qxd 2/17/2010 3:22 PM Page 172
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 173
Clam
ps an
d W
orkh
old
ing
VISE ACCESSORIESCopper Jaw Caps
Designed to fit any size vise to avoid marring the surface of softermetals and to protect jaw faces. They have polished faces andpliable copper extensions to fit on any make of vise. Sold in pairs.
Cat. No.Jaw
WidthPrice
per PairWLT-385 31/2 32.00WLT-390 4 35.20WLT-395 41/2 40.00WLT-400 5 51.20WLT-405 6 78.40
Magnefix Jaw Caps
Designed to protect both the vise jaws and the work piece from marring and distortion. Constructed from hardened aluminum alloy withtwo built-in circular magnets on the back side which hold the caps securely on the vise. They are right-angled and surface-parallel to fitany vise type including machine and bench type. Sold in pairs.
Standard Fiber Prism Rubber
SOFT JAWS™ MAGNETIC JAW CAPS
Soft polyurethane protects work from damage. Impervious tosolutions and chemicals. Caps come in vibrant colors andremains soft in hot or cold environments. Strong magnets holdcaps in place. C-45 and C-60 are smooth but drillable for round orspecial applications. The C-40 and WLT-60 are grooved for roundor tube applications. Sold in pairs.
Smooth
Grooved
Cat. No. Style Width Color Price per PairC-45 Smooth 41/2 Orange 10.19C-40 Grooved 41/2 Yellow 10.19C-60 Smooth 6 Green 12.19WLT-60 Grooved 59/16 Yellow 12.00
UNIVERSAL WORK POSITIONER
This all purpose, all position workholding fixture allows you tomove your workpiece to any position, eliminating the need forelaborate setups with clamps, vises, angle plates, etc. It ismachined from 6061-T6 aluminum (no castings) and has beenhardcoated, adding wear resistance to the work surface andthreaded mounting holes. Allows spherical movement of 180° anda table rotation of a full 360°. Only one torque setting is requiredper setup. Excellent for soldering, welding, brazing, assembly,model making, electronic device mounting, etc.
TableSize
MountingHoles
BaseSize
WorkLoad (Lbs.)
PriceEachCat. No. Height
WP-4 4 x 4 x 3/8 48 (1/4-20) 11/2 x 11/2 x 1/4 10 37/8 139.67
QUICK ADJUSTING PUSH BUTTONSTOP NUTS
Allows quick and accurate adjustments of stop settings. Used withexisting stop screws and fits all imported or domestic millingmachines. To operate, simply depress the button and slide the nutto the desired position. Releasing the nut locks it into position andthen turning the nut gives you .001” micrometer adjustments.Saves hours of time and is easy to use. Available in steel oraluminum construction. Steel (pictured) has standard housing andaluminum has tapered housing.
Price Each1-4
Price Each1-4Cat. No. Thread OD OAH Cat. No. Thread OD OAH
Steel - Standard Housing Aluminum - Tapered HousingQAN-1 1/2-20 11/2 1 47.25 QAN-4 1/2-20 11/2 1 30.15QAN-3 1/2-13 11/2 1 50.85 QAN-5 1/2-13 11/2 1 30.15
QUILL STOPSClip-On
Each stop is assembled, faced off, and then drilled and tapped.Made in U.S. Quick action clipping for fast installation andremoval. Easily positioned with positive locking action. Sturdyaluminum knobs.Cat. No. Description Price EachCQS-5 1/2-20 Threads For Mills 19.88
Standard Fiber Prism RubberJaw
Width Cat. No.Price
per Pair Cat. No.Price
per Pair Cat. No.Price
per Pair Cat. No.Price
per Pair4 WLT-435 32.00 WLT-465 35.20 WLT-495 36.80 WLT-525 35.20
41/2 WLT-440 33.60 — — WLT-500 38.40 — —5 WLT-445 33.60 — — WLT-505 38.40 WLT-535 36.806 WLT-450 36.80 — — WLT-510 40.00 WLT-540 38.40
0173.qxd 2/17/2010 3:23 PM Page 173
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!174
Cla
mp
s an
d W
ork
ho
ldin
gPRECISION VISES
Three Way Tilting Machine Vises
• Perfect vise for three axis jobs in milling, drilling, shaping and jigboring
• Made of close-grained high tensile cast iron• Jaw plates are hardened and ground• 360° swivel base• Accurately indexed for three way angular work• 45° tilting range on either side• 90° vertical indexing• Bases have keyways and bolt slots for machine mounting
Cat. No.Jaw
WidthJaw
OpeningJaw
DepthWgt.Lbs.
PriceEach
WLT-1200 3 3 15/16 24 576.00WLT-1205 4 4 19/16 46 720.00
Toolmaker’s Vise
• Made from specially selected alloy steel• Precision ground square and parallel to .0002”• Heat treated for hardness• Completely stress relieved
JawWidth
JawOpening
JawDepth
Wgt.Lbs.
PriceEachCat. No.
WLT-1210 23/4 3 19/16 11 448.00
Toolmaker’s Screwless Vises
• All steel body uses rapid positioning notches to obtain positivedownward clamping force
• Horizontal and vertical vees in sliding jaws hold workpiecessecurely and accurately
• Squareness and parallelism to within .0003”Jaw
WidthJaw
OpeningJaw
DepthWgt.Lbs.
PriceEachCat. No.
WLT-1215 2 31/8 1 8 216.00WLT-1220 3 33/4 13/8 11 304.00
Self Centering Vise
• Used on milling and drilling machines where quick centering isrequired
• Automatically adjusts workpiece to its center• Made of close-grained cast iron• Swivel base provides positive locking mechanism that adjusts
through 360°• Opposite threads for quick, accurate centering
JawWidth
JawOpening
JawDepth
Wgt.Lbs.
PriceEachCat. No.
WLT-1235 4 4 11/2 32 448.00
VISES
90° Angle Vise Clamp
Takes the work out of applicationsthat involve holding materials forright angle joining, assembling,welding or grinding. A self-centeringjaw quickly adjusts to clampworkpieces, even accommodatingpieces of different sizes. Made ofcast iron, zinc plated. The spindle iscopper plated to resist weld spatter.
CapacityMiter
JawHeight
JawLgth.
ShippingWgt. (Lbs.)
PriceEachCat. No.
WLT-225 311/32 13/8 41/8 81/2 104.00
Angled Drill Press Vises
JawWidth
Max.Opening
JawDepth
OverallHeight
ShippingWgt. (Lbs.)
PriceEachCat. No.
WLT-250 21/2 21/2 11/2 37/16 12 72.00WLT-255 3 31/8 13/4 41/4 17 96.00
Clamp-On Vise
This portable clamp-on vise allows foruse in many different applications.Features a fully enclosed spindle,double lock downs, grooved replace-able jaws and a swivel base.
Max.Opening
ShippingWeight(Lbs.)
PriceEachCat. No. Jaw Width Jaw Depth
WLT-1130 21/2 2 21/2 13 104.00
Woodworker’s Vise
This light and medium-duty vise features double guide-bars,continuous screw action and solid steel dog.
• Castings - gray iron with orange baked-enamel finish• Jaws - drilled and tapped or countersunk holes for attachment
of wood facings• Dog - solid steel
Cat No. Jaw Width Maximum Opening Price EachAC-27090 7 9 58.68
Mounted on an angle base allowing thevise to be adjusted quickly to any anglefrom 0° to 90° vertical. Precision lockingbolts, linked by side plates of highquality steel, lock the vise securely. It iscalibrated for vertical angle readings.
0174.qxd 2/17/2010 3:23 PM Page 174
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 175
Clam
ps an
d W
orkh
old
ing
VISESGrip-Master Screwless Vises
The Grip-Master screwless vise offers many advantages.Instantaneous, effortless setting by simply pushing on the knobcontrolling the movable jaw. Guaranteed positive locking by lightpress on locking lever. Built-in, recessed parallels level work. Largeloading and unloading capacity. Hardened and ground bars andlocking mechanism insure long life. Straight through drilling permit-ted by extra-wide clearance in base. Hardened and ground V-blockattachment available for holding round or oval work securely.
V-Block Attachment Holds Round Stock
Vises V-Blocks
Cat. No.Jaw
WidthMax.Open
Jaw Depth
ParallelDepth
PriceEach Cat. No.
Price Each
GM-1 3 3 11/4 5/8 142.78 VB-1 38.72GM-2 4 411/16 11/4 5/8 202.07 VB-2 44.77GM-3 6 65/16 113/16 5/8 264.99 VB-3 58.08GM-4 8 83/8 2 5/8 375.10 VB-4 72.60
Grip-Master Fixture Locks
Adaptable to a wide range of applications and simplifies jig andfixture designing and eliminates special locking details. A simplepush or pull on the bar knob sets the bar instantaneously at anyposition between fully open or fully closed. A light press on thelocking lever gives an extra forceful forward motion to the bar,exerting a holding pressure, adjustable from 400 to 1,100pounds. Actually compensates for variations in size of work. Itslong stroke assures wide work clearance and permits quickremoval of chips and burrs. No screw threads to wear or strip.Hardened and ground bar and locking mechanism. Bar left softfor 1” on work end for easy machining when adapting it to fixture.
Cat. No. A B C D E F G H I JPriceEach
GMF-1 35/16 33/16 27/8 9 .493 21/2 23/16 13/32 11/2 3/4 81.07GMF-1-10 35/16 33/16 27/8 10 .493 21/2 23/16 13/32 11/2 3/4 83.49GMF-1-12 35/16 33/16 27/8 12 .493 21/2 23/16 13/32 11/2 3/4 85.91GMF-1-14 35/16 33/16 27/8 14 .493 21/2 23/16 13/32 11/2 3/4 87.12GMF-1-16 35/16 33/16 27/8 16 .493 21/2 23/16 13/32 11/2 3/4 84.70GMF-1-18 35/16 33/16 27/8 18 .493 21/2 23/16 13/32 11/2 3/4 93.17GMF-1-24 35/16 33/16 27/8 24 .493 21/2 23/16 13/32 11/2 3/4 98.01GMF-2 45/16 311/16 315/16 10 .742 31/2 27/8 17/16 21/8 11/4 96.80GMF-2-12 45/16 311/16 315/16 12 .742 31/2 27/8 17/16 21/8 11/4 104.06GMF-2-14 45/16 311/16 315/16 14 .742 31/2 27/8 17/16 21/8 11/4 106.48GMF-2-16 45/16 311/16 315/16 16 .742 31/2 27/8 17/16 21/8 11/4 110.11GMF-2-20 45/16 311/16 315/16 20 .742 31/2 27/8 17/16 21/8 11/4 116.16GMF-2-24 45/16 311/16 315/16 24 .742 31/2 27/8 17/16 21/8 11/4 118.58
Drill Press Vises
These handy drill press vises can be used from three sides. Workcan be leveled quickly because jaws have built-in parallels. Widelyspaced jaw guide bars, permit drilling clear through work. Jaw sidesare precision ground at right angle to parallels to permit accuratedrilling from the sides without resetting the work. Horizontal V-groove, holds round stock firmly for side and end drilling.
Cat. No.Jaw
WidthJaw
OpeningJaw
DepthWeight
Lbs. Price EachDPV-20 6 10 2 21 217.80DPV-30 8 10 21/2 36 309.76
Speed Type Vises
Designed for speed. Screw and nut hardened for long life. Heavysemi-steel castings, for strength. Heavy steel base plate, for rigid-ity. Standardized holes in jaws, for attaching interchangeable jawplates and fixtures. The screw is held positively in the nut whenthe vise is clamped. It cannot slip; yet it is released instantly witha half-turn. Lift the screw and the jaw is free to slide to its fullopening. Slide the jaw to the closed position, drop the screw intothe nut and lock with a half turn. Combination of jaw plates aregrooved for holding round parts, notched for holding parts abovebase of vise, smooth on back side. They are accuratelymachined, hardened and ground. Socket cap screws supplied forattaching them to vise. Vises are supplied without jaw plates.
Vises Without Jaw Plates Jaw Plates
Cat. No.Jaw
WidthJaw
DepthMax.
OpeningWeight
Lbs. Price Each Cat. No.Price
Per SetCV-4 4 11/2 4 121/2 227.11 JP-4 58.40CV-6 6 2 6 31 295.89 JP-6 86.96CV-7 6 2 8 40 397.11 — —
POW-R-ARM ERGONOMIC WORKPOSITIONERS
These work positioners put the workpiece where you want it and holdit tight for hands free production. Repositions workpieces easily andaccurately, eliminating time consuming clamping and unclamping.
Midget 345
Fast on-off action with horizontalhandle. All parts are steel. For intricatesmall work. 6 lbs. capacity.
BaseDia.
OverallHgt.
MountingStud
PriceEachCat. No.
WLT-300 21/2 41/4 5/16-24 136.00
Veep 344
The horizontal handle is easily accessi-ble. Steel body. 1/2” receptacle with setscrew for vise, printed circuit boardholder or special fixture. 20 lbs. capacity.
Cat. No. Base Dia. Overall Height Price EachWLT-305 33/4 41/4 168.00
Mechanical 301
Extra strong, heavy duty positionerwith exceptionally fast on-off action.Body is machined steel, all steel parts.Mounting holes are 5/16-18 on center.Designed for high production assemblylines. 70 lbs. capacity.
Cat. No. Base Dia. Overall Hgt. Price EachWLT-315 6 8 456.00
Junior 343
Fast on-off action with horizontalmoving lock handles. Body is castaluminum with steel parts. Mountingholes are 1/4-20 on 2-1/4” centers. T-bracket. 30 lbs. capacity.
Cat. No. Base Dia. Overall Hgt. Price EachWLT-310 41/4 51/4 200.00
0175.qxd 2/17/2010 3:24 PM Page 175
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!176
Cla
mp
s an
d W
ork
ho
ldin
gVISES
Anglock® Vises
1
3 4
2
The Kurt™ Anglock® D-series vises are designed for precision part clamping on basic machine tools such as knee-type mills, grinders,and machining centers. Vises are ideal for extremely high accuracy tool and mold applications and for use in running production partswhere datums, flatness and parallelism is important. Anglock® design assures the movable jaw does not lift. Semi-hard steel screw,80,000 psi ductile iron construction. Both are machined, which allows you to indicate alignment during set up. Swivel base (soldseparately) allows positioning increments of 1°. Other Kurt™ vises are available as a special order. Please call for price and delivery.
Note: KV-D810 shipped via truck.
AFF
H
G (4 Places)
C
Hex
BE
D 2.00Vise Swivel Base
Cat. No.
Jaw OpeningMax
A B C D E F G±.001
HWt.Lbs.
PriceEach
KV-D675 7.50 6 1.735 16.75 8.75 .725 .688 2.875 78 487.80KV-D688 8.80 6 1.735 16.81 8.75 .725 .688 4.61 78 568.90KV-D810 10.00 8 2.200 21.81 11.50 1.075 .813 3.31 158 1526.80KV-D60-4-SA Swivel Base Only for KV-D675 and KV-D688 324.00
Max. CapacitiesModel 1 2 3 4 Hex SizeKV-D675 7.50 10.50 13.12 15.87 .750KV-D688 8.80 11.50 14.32 17.03 .750KV-D810 10.00 13.50 17.25 20.75 .875
Aluminum center hub with all steel handles and knobs. Blackoxide finish.Cat. No. Description Price EachVSH-5 Fits 4” Vise (9/16” Hex) 31.50VSH-15 Fits 6” Vise (3/4” Hex) 31.50VSH-20 Fits 8" Vise (7/8” Hex) 31.50
Vise Work Stops
Cat. No. Fits Vise Model Price EachKV-D30-45 3-4 Inches Wide 110.00KV-360PWS 5-6 Inches Wide 138.00
Parallel Keeper
Cat. No. Max. Opening Capacity Price EachKV-KPS6000 6" 62.00
Vise Keys - Stepped
Vise keys are used to align your vise toyour milling machine table. All keys arehardened. Step keys are used whenkeyway in the vise is different than thatof the machine T-slot. Sold in pairs.
Cat. No. Key Size Vise Size Price Per PairKV-D30-33A 1/2 x 5/8 3" and 4" 34.00KV-D50-33A 11/16 x 5/8 5" and 6" 35.00KV-D50-33B 11/16 x 13/16 5" and 6" 35.00
MACHINIST’S JACK
Use on drill presses, shapers milling machines, planers andelectric appliances or any place leveling is needed. Heavy caststeel base with adjustable screw and tilting swivel head and locknut for permanent positioning. Approximately 1,000 lbs. capacity.3” high, 4” fully extended.Cat. No. Description Price EachGEN-7 Machinist’s Jack 7.36
JACK SCREWS
Handy for leveling work on planer beds, upright drills, machineryset up and general shop use. They are 1-1/4” diameter at baseand have a range from 2-1/4” to 3-3/8” and can raise over 1,000pounds. The set contains the jack, two extension bases (allowsup to 6-3/8” height), auxiliary pointed screw, and two extensionbases for irregular surfaces.Cat. No. Starrett Description Price EachSTR-S190 S190 Complete Set 49.00STR-190A 190A Jack Only 18.00STR-190D 190D Auxiliary Pointed Screw Only 6.20
Vise Speed HandlesFor Kurt Style Milling Machine Vises
0176.qxd 2/17/2010 3:24 PM Page 176
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 177
Clam
ps an
d W
orkh
old
ing
WORK STOPS FOR MILLINGFor Quick and Easy Positioning of Workpieces
Bolts on to vise without any modifications. Works on either rightor left side with any jaw height. Quick adjusting, perfect forproduction runs.Cat. No. Description Price EachAWS-10 Fits 5-6” Vise 37.71
PRECISION ADJUSTABLE MILL STOPA Rigid Stop for Milling Set Ups
Designed for use on milling machines, jig borers, and horizontaland vertical milling set ups. Used with angle plates, vises, jigs,etc. to serve as a rigid stop. 1/2” hole for T-slot mounting, 3/8”diameter rod, 2” x 4-1/2” base with 7” overall height. Steel withblack oxide finish.Cat. No. Description Price EachAMS-5 Adjustable Mill Stop 39.25
V-BLOCKS AND CLAMPSHardened and Ground
Can be used on base, on end and on either side because clampis within the outside width of the block. Provided with anadjustable side screw with caps to prevent tilting when drilling,grinding, or milling. It has hole clearance for drilling and removingdowel pins. Features four 3/8-16 tapped holes, two on base andone on each side, so it can be attached to an angle iron. Theblock is 1-7/8” square and the base is 3-1/2”. Capacity is 1-5/16”.Cat. No. Starrett Description Price EachSTR-28010 567 V-Block & Clamp 265.00STR-28015 567B Clamp Only 35.00
ADJUSTABLE WORK STOPEXTENSIONS
Designed to fit Kurt vises. Allows for quick set-ups and solid locat-ing of work pieces longer than 6”. Made from 6105-T, T-Slottedaluminum extrusion. Main rails shown below allow for effectivetravels of 36” and 54”. Easily mounts to vise jaw with two 1/2-13 x1-3/4” socket head cap screws. Mounting hole spacing is 3.875”on center. Mounting hardware included. Additional sizes availableas special order. Please call for price and delivery.Cat. No. Description Price EachTST-2336 36" Travel Adjustable Work Stop Extension 66.77TST-2354 54" Travel Adjustable Work Stop Extension 74.31
VISE WORK STOP
Quick and easy to use. Attaches to any vise jaw (1/2” through 1”wide) with one screw adjustment. Made from hardened steel,black oxide finish. Stop is 1” wide x 1-7/16” long.Cat. No. Description Price EachEVS-5 Easy Vise Work Stop 12.50
SPIDER HANDLES FOR MILLS
Replaces the standard quill feed handle on most millingmachines. Perfect for all drilling operations. Features a 3” diame-ter solid aluminum machined center with a 1” bore. Three heavyduty solid steel spokes extend 6-1/2” from the center. Platedfinish.Cat. No. Description Price EachSHM-5 Spider Handle for Mills 26.86
0177.qxd 2/17/2010 3:24 PM Page 177
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!178
Cla
mp
s an
d W
ork
ho
ldin
gC-CLAMPS
400 Series C-ClampsDrop Forged, Regular Duty, Extra Deep Throat
Cat. No.Opening Capacity
ThroatDepth
SpindleDia.
PriceEach
WLT-402 0 - 21/2 21/4 9/16 14.40WLT-403 0 - 3 21/2 9/16 15.00WLT-404 0 - 4 31/4 3/4 25.60WLT-406 0 - 61/16 41/8 3/4 38.40WLT-408 0 - 81/4 5 3/4 48.00WLT-410 2 - 101/8 6 3/4 70.40WLT-412 2 - 121/4 65/16 7/8 114.40
Regular Duty - High Visibility
• Drop forged steel frame• High visibility yellow — meets OSHA standards• Tough durable finish• V-grooved anvil prevents slippage
ThroatDepth
SpindleDia.
Min ProofTest Lbs.
PriceEachCat. No. Capacity
WLT-655 0-3 21/2 9/16 3,500 17.60WLT-660 0-41/2 31/4 3/4 6,200 25.60WLT-665 0-61/16 41/8 3/4 6,900 38.40WLT-670 0-81/4 5 3/4 6,600 48.00
Heavy Duty
• For heavy industrial applications• Forged from superior quality steel• Spindle turned from single piece of square bar stock• Grey lacquer finish
ThroatDepth
SpindleDia.
Min. ProofTest Lbs.
PriceEachCat. No. Capacity
WLT-710 0-4 23/8 3/4 10,000 88.00
Regular Duty - Slip-Not
• Drop forged steel frame• Grooved anvil— to grip and hold tight• Serrated pad for sure bite and secure clamping• Plated to resist weld spatter
ThroatDepth
SpindleDia.
Min. ProofTest Lbs.
Price EachCat. No. Capacity
WLT-755 0-3 21/2 5/8 3,500 19.20WLT-760 0-41/2 31/4 3/4 6,200 26.40WLT-765 0-61/16 41/8 3/4 6,900 42.40
Instant Action
• Instant action spindle release for quick clamping• Disengage screw with thumb press only • Made from high strength, ductile iron
Throat Depth
SpindleDia.
Min. ProofTest Lbs.
PriceEachCat. No. Capacity
WLT-45458 0-21/2 111/16 1/2 2,040 13.69
C-Clamp Pads
Update your Wilton clamps (and other American manufacturedC-clamps) with these adapter swivels. Includes pad and C-clip.Installs with a screwdriver.
Flat Pad Serrated Pad
ForSpindle
Price Each1-9
For Spindle
Price Each1-9Cat. No. Cat. No.
WLT-1105 9/16 and 5/8 6.40 WLT-1115 9/16 and 5/8 10.57WLT-1110 3/4 and 7/8 8.00
Clamp Grips
Soft, durable handle press fits over T-handle on “C” and “L”clamps. Provides comfortable grip. Press on middle or on the endfor greater torque. High visibility yellow. Fits many competitormodels.
Fits WiltonClamps
HandleLgth.
SpindleDia.
Cross BarDia.
PriceEachCat. No.
WLT-STGA 402, 403 35/8 5/8 5/16 11.73WLT-STGB 404 51/8 9/16 5/16 11.73
0178.qxd 2/17/2010 3:25 PM Page 178
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 179
Clam
ps an
d W
orkh
old
ing
CLAMPSC-Clamps
This line of Pony “C” clamps is an imported product manufacturedin Pony’s exclusive factory under strict guidelines that providesquality at an affordable price. Smoothly cut acme threads areprotected with a bright plated finish. Ductile cast iron frames arepowder-coated bright Pony orange for high visibility and lastingprotection.Cat No. Opening Size Throat Depth Price EachAC-2610 0-1 1 1.51AC-2615 0-11/2 11/2 2.35AC-2620 0-2 1 2.15AC-2622 0-21/2 13/8 3.77AC-2630 0-3 2 4.28AC-2640 0-4 3 7.07
C-Clamp
• Heat treated ductile iron frame• Square thread screws• Steel internal tooth washers on swivel for holding
Cat No.Opening
SizeThroatDepth
ScrewDia.
Normal LoadLimit Lbs.
PriceEach
AC-103 0-3 17/8 9/16 1,800 11.99AC-104 0-4 21/8 5/8 2,400 15.06AC-105 0-5 21/2 5/8 2,400 21.71AC-106 0-6 23/4 5/8 2,400 22.53AC-108 0-8 31/4 3/4 2,400 31.98
C-ClampsDeep Throat Pattern
Capacity Throat Depth fromCenter of ScrewCat. No. Max. Min. Price Each
ABT-78-404 4 0 31/4 29.11ABT-78-406 6 0 41/8 40.12ABT-78-408 8 0 5 52.95ABT-78-410 10 3 6 67.18
Welder’s C-Clamp
• Heat treated ductile iron frame, black baked enamel finish• Square thread screws• Steel internal tooth washers on swivel for holding• Copper plated screws, sliding pins and swivels protect against
weld spatter
Cat No.Opening
SizeThroatDepth
ExtremeDepth
ScrewDia.
Normal LoadLimit Lbs.
PriceEach
AC-1123 0-23/4 21/4 23/4 9/16 4,000 21.87AC-1125 0-43/4 3 35/8 5/8 4,000 34.48
Pony C-ClampsMalleable Frames - Rust-Proofed
Knurled Sliding Pin Thumb Screw
OpeningSize
ThroatDepth
ScrewDia.Cat. No. Type of Handle Price Each
PC-1 5/8 7/8 #12 Knurled 3.45PC-2 1 11/8 1/4 Sliding Pin 3.82PC-4 11/4 13/8 5/16 Thumbscrew 5.44PC-5 11/2 11/2 5/16 Sliding Pin 5.66PC-6 11/2 31/2 5/16 Sliding Pin 9.50PC-7 2 1 5/16 Sliding Pin 5.49PC-8 21/2 13/8 3/8 Sliding Pin 8.34PC-9 21/2 21/2 3/8 Sliding Pin 10.36PC-10 21/2 43/4 3/8 Sliding Pin 22.74PC-12 3 13/8 7/16 Sliding Pin 10.36
3-Way Edge Clamp
Three screw design permits right angle screw to be centered, orpositioned above or below center, on varying thicknesses of work.Used for light duty welding, cutting, trimming and gluing. Made ofmalleable iron. Bright plated.
Discount 2 applies.
OpeningCapacity
Depth ofThroat
ScrewDia.
Price Each1-11Cat. No.
TWC-3325 21/2 21/2 3/8 12.78
Bessey® F-Style All Steel Bar Clamps
Easy to use. Slidemoveable arm into positionand tighten screw spindle.Provides instant clampingat any opening. Saves timeover ordinary C-clamps.Deep throat allows forgreater reach.
Discount 44 applies.Jaw
OpeningThroatDepth
SpindleDia.
ClampPressure
Price Each1-9Cat. No.
Regular DutyBLC-15 0-4 43/4 .563 1,330 33.23Heavy DutyBLC-25 0-8 51/2 .775 2,600 60.03BLC-50 0-12 51/2 .775 2,600 83.08BLC-60 0-20 51/2 .775 2,600 103.99Extra Heavy DutyBLC-70 0-12 7 .850 4,880 158.67BLC-80 0-18 7 .850 4,880 182.79BLC-90 0-36 7 .850 4,880 210.13
Pivot Handle L-Clamps
The pivoting plastic handle revolves 90° allowing greater leverageand faster clamping in restricted places.
ThroatDepth
RailSize
SpindleDia.
PriceEachCat. No. Opening
WLT-965 16 43/4 1 x 15/32 3/4 48.33
0179.qxd 2/17/2010 3:25 PM Page 179
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!180
Cla
mp
s an
d W
ork
ho
ldin
gC-CLAMPS
Kant-Twist® Clamps
The Kant-Twist® multi-purpose clamps combine the best featuresof ordinary C-clamps and parallel clamps. Lightweight, yet 40%stronger than C-clamps. Designed to eliminate distorting or twist-ing action and the floating jaws always stay parallel. Built-inV-blocks for round stock. Copper plated jaws and screws are idealfor welding clamps.
Round Handle - Copper Plated Jaws
DE
A BC
Round Handle -Copper Plated Jaws
Max.A
Max.B
RatedLoadCat. No. C D E Price Each
KT-396 3/4 3/8 13/8 11/2 3/8 200 10.45KT-401-1 11/16 1/2 13/4 21/8 1/2 350 11.69KT-405-1 2 11/8 31/4 31/2 11/4 800 15.10
T-Handle and L-Handle - Copper Plated Jaws
T-Handle and L-Handle -Copper Plated Jaws
T-HandleCat. No.
L-HandleCat. No.
Max.A
Max.B
RatedLoadC D E Price Each
KT-401 — 11/16 1/2 13/4 21/8 1/2 350 10.80KT-405 KT-405-L 2 11/8 31/4 31/2 11/4 800 13.07KT-407 KT-407-L 27/16 2 41/16 41/8 113/16 700 14.38KT-410 KT-410-L 3 11/4 5 51/4 13/4 1,500 18.67KT-415 KT-415-L 41/2 21/4 63/4 7 21/2 1,700 19.95KT-420 — 6 21/8 81/4 81/4 33/8 2,000 30.43KT-421 — 6 41/2 10 11 51/2 2,000 33.20— KT-430 9 33/8 13 12 51/4 2,500 88.14— KT-435 10 6 15 16 7 3,500 124.17
T-Handle - Polyurethane Jaws
T-Handle -Polyurethane Jaws
Max.A
Max.B
RatedLoadCat. No. C D E Price Each
KT-410-8 3 11/4 5 51/4 13/4 1,500 23.34KT-415-8 41/2 21/4 63/4 7 21/2 1,700 24.61
T-Handle - 303 Stainless Steel
T-Handle - 303Stainless Steel
Max.A
Max.B
RatedLoadCat. No. C D E Price Each
KT-510 3 11/4 5 51/4 13/4 1,200 43.87KT-515 41/2 21/2 63/4 7 21/2 1,500 50.78
Handle Grips
For use with T-handle clamps. Made of high quality ABS plastic.Taps easily on and off.
A
B
Cat. No. A B For Use With Models Price EachKT-1 1/2 11/2 401 1.37KT-2 11/16 21/2 405, 407 2.75KT-3 7/8 4 410, 415, 510, 515 3.90KT-6 11/8 5 420, 421 4.40
CLAMPS
Clippix Plastic Spring Clamps
• Made from durable, lightweight polyamide• Ergonomic 2-component handle designed
for comfort and a firm grip
Cat No. Throat Depth Clamping Capacity Price EachBLC-300 3/4 3/4 1.06BLC-301 11/8 1 2.15BLC-302 11/2 13/4 2.42BLC-303 115/16 2 2.64BLC-304 11/2 2 2.30BLC-305 23/4 3 5.99
Allows pressure adjustment from 1 to 50 pounds of clampingforce. The jaws and handles are made of glass filled nylon.Springs are heavy duty tempered steel. Soft, pivoting, plastic jawpads to hold irregular shaped objects.
JawOpening
JawLength
JawReach
PriceEachCat. No.
AC-3251 1 41/2 11/4 4.37AC-3252 2 61/2 21/8 6.39
Spring Clamp
Spring clamps are extra hands. Use on wood, metal, fabrics,plastic or anywhere spring pressure is adequate and fast applica-tion/removal is important. Jaws on the 2” and larger jaw openingsizes are shaped for holding round stock. Poly-vinyl coated tipsprevent marring and coated handles provide cushioned grip.Made of cold-finished steel, plated.
Discount 2 applies.
No CoatingCoated Tipsand Handles
Coated Handles
JawOpening
JawLgth.
JawReach
Price Each1-11Cat. No. Description
PSC-5 No Coating 1 4 11/4 1.56PSC-10 Coated Handles 1 4 11/4 2.22PSC-20 Coated Tips and Handles 1 4 11/4 2.47PSC-25 No Coating 2 6 2 3.05PSC-30 Coated Handles 2 6 2 3.51PSC-40 Coated Tips and Handles 2 6 2 3.82PSC-45 No Coating 3 9 3 7.75
SuperGrips™ Clamp
Great for use in welding, drilling, assembly, maintenance and forgeneral clamping. Instant locking clamps are fast and strong.Hardened steel rails, heat treated chrome vanadium forged steeljaws.Discount 44 applies.
ThroatDepth
ClampPressure
Price EachCat. No. Opening 1-9SGC-15 4 21/2 440 75.04SGC-20 8 21/2 440 85.76
Pressure Adjusting Spring Clamps
0180.qxd 2/17/2010 3:25 PM Page 180
Call 800.253.0421 Click ReidSupply.com REID SUPPLY 2010/2011 181
Clam
ps an
d W
orkh
old
ing
• Change from clamping to spreading by simply twisting the dial– no disassembly
• Handle with pump lever parallel to the rail• Convenient one-handed operation• All around clamping – in front of, behind and at the side of the
rail
BAR CLAMPSHeavy-Duty Steel Bar Clamps
Made for all types of heavy-duty clamping. Used by cabinet-makers, woodworkers, metalworkers or for home shop anddo-it-yourself projects. Protective pads made of thick, durableplastic. Clamps rest parallel on work surface for ease of workplacement and adjustment.
• Reach - 3” from edge of the bar to center-line of screw• Bar - 1” x 5/16” plated, round edge, high carbon steel• Castings - malleable and/or ductile iron; powder coated orange
finish• Screw - 1/2” diameter cold-drawn steel with special, smoothly
cut ACME threads• Handle - varnished hardwood with plated steel ferrule• Clutch discs - hardened, plated steel; three clutch discs and one
clutch spring constitute the multiple-disc-clutch• Swivel - 1-13/16” diameter; exclusive Jorgensen design with
steel internal tooth washer for positive “stay on” power
Steel Bar Clamps
Used by homecrafters, cabinet-makers, woodworkers and metal-workers. The sliding head is threaded to accommodate the screw.All adjustments are made in the moveable sliding head, makingthis style fast-acting, easy to open and close and suitable for“close quarters” clamping. Strong, lightweight steel bars are rust-resistant. Multiple-disc-clutch holds securely at any point alongthe bar.• Reach - 2-1/2” from edge of bar to center-line of screw• Bar - 1/4” x 3/4” plated, round-edge, high carbon steel• Castings - malleable and/or ductile iron; powder coated orange
finish• Screw - 3/8” diameter cold-drawn steel with special, smoothly
cut U.S.S. threads• Handle - varnished hardwood with plated steel ferrule• Clutch discs - hardened, plated steel; two clutch discs and one
clutch spring constitute the multiple-disc-clutch
Clutch Style Bar Clamps
• Powder coated, ductile cast iron jaws• Two piece slip clutch plates• Nickel plated, drawn serrated rail• Non-marring pads on the top and bottom jaws• Ergonomically shaped wood handle
Cat No. Throat Depth Clamping Capacity Load Limit Lbs. Price EachBLC-200 21/2 6 600 12.75BLC-201 21/2 12 600 14.46BLC-202 21/2 18 600 17.04BLC-203 21/2 24 600 18.75BLC-204 21/2 30 600 20.68BLC-205 21/2 36 600 21.75BLC-206 31/2 12 1000 25.29BLC-207 31/2 18 1000 29.69BLC-208 31/2 24 1000 33.76BLC-209 5 12 1200 42.88BLC-210 5 18 1200 52.31BLC-211 5 24 1200 59.49
Steel Bar Clamps
Used for commercial metalworking, heavy fabricating and indus-trial welding applications. Crank handle, notched steel bar clampsare simple to operate. High carbon steel bars are notched at oneinch increments for easy positioning of the tail stops. Fixed headis threaded to accommodate the screw. Screws and handles usedfor final clamping adjustment only.
Cat. No.Max. Opening
CapacityNormal
Load Limit Lbs.Clamping
Faces Bar TypePriceEach
AC-6024 24 4,000 13/4 x 11/2 13/8 x 5/16 46.03AC-6030 30 4,000 13/4 x 11/2 13/8 x 5/16 48.81AC-6036 36 4,000 13/4 x 11/2 13/8 x 5/16 51.39AC-6048 48 4,000 13/4 x 11/2 13/8 x 5/16 57.30AC-6060 60 4,000 13/4 x 11/2 13/8 x 5/16 75.03AC-6072 72 4,000 13/4 x 11/2 13/8 x 5/16 66.80
Bar and Spreader Clamps
Converts easily from bar to spreader clamp. Spring loaded headmaintains greater applied force than other one handed clamps.Thumb release clutch disc for one - handed opening and closing.Full size soft plastic pads for maximum work protection.
Discount 2 applies.
Bar Clamp Position
Spreader Position
Cat. No. Max. Opening CapacityPrice Each
1-11ACC-3410 10 19.95ACC-3416 16 21.53ACC-3428 28 25.07
DuKlampsOne-Handed Clamping and Spreading
Cat No. Throat Depth Clamping Capacity Clamping Force Price EachBLC-100 21/2 6 180 24.65BLC-101 21/2 12 180 25.72BLC-102 31/4 6 260 27.33BLC-103 31/4 12 260 28.51BLC-104 31/4 18 260 32.15BLC-105 31/4 24 260 34.30
Cat No. Max. Opening Capacity Load Limit Lbs. Price EachAC-3712-HD 12 1000 16.34AC-3724-HD 24 1000 19.79AC-3736-HD 36 1000 23.84
Cat No. Max. Opening Capacity Load Limit Lbs. Price EachAC-3706 6 600 12.49AC-3712 12 600 13.84AC-3718 18 600 15.28AC-3724 24 600 16.68AC-3736 36 600 20.33
0181.qxd 2/17/2010 3:26 PM Page 181
REID SUPPLY 2010/2011 Order more, save more: Quantity Discounts on Back Cover!182
Cla
mp
s an
d W
ork
ho
ldin
gCLAMPS
Quick-Action BandClamps™
Ideal for temporary hose and tube connections, maintenance andrepeated use such as testing, filter bags, dust gaiters, molds, etc.Made from 304 stainless steel. Slotted screw adjustment anddraw latch for quick clamping. Band is .63” wide.
Discount 44 applies.
Dia.Range
UltimateStrength Lbs.
Price EachCat. No. 1-9PX-115 2.76-4.53 300 37.80PX-135 3.54-5.31 300 35.60PX-175 5.12-6.89 300 37.64PX-215 6.69-8.46 300 39.56PX-255 8.27-10.04 300 41.55PX-295 9.84-11.61 300 43.52PX-335 11.42-13.19 300 45.44PX-375 12.99-14.76 300 47.43PX-415 14.57-16.34 990 66.31PX-615 22.44-24.21 990 91.11
Pipe Clamp Fixture
One set of fixtures may be used to make any number of barclamps simply by mounting on different lengths of 3/4" black pipe.Made of malleable iron with baked enamel finish. Pipe is notincluded.
Discount 44 applies.
Price Each1-9Cat. No. Description
PCF-50 3/4” Pipe Clamp Fixture 18.83
Band Clamp
Used for clamping large round, rectangular and irregular shapes.2” wide canvas band. Positive hold is afforded by the dual self-locking cast iron cams which allow the band to be pulled tightfrom either or both sides. Malleable iron coating with orange-baked enamel finish. Crank handle.
Cat. No.Length OfBand (Ft.)
PriceEach
AC-6210 10 100.87AC-6215 15 112.62
0182.qxd 2/22/2010 10:48 AM Page 182