Präzise Mess– oder Kontrolldorne zur Abnahme von Werkzeugmaschinen gemäß ISO-Empfehlung R230 sowie zur Überprüfung des Rundlaufs und zum Ausrichten der Maschinenspindel. Rundlaufgenauigkeit Kegel zu Schaft ≤ 0,003 mm Lieferung mit Messprotokoll Holzkiste zur Aufbewahrung bitte separat bestellen (siehe S. 7) NL = nutzbare Messlänge
Precise test arbors for the inspection of machine tools according to ISO recommendation R230 as well as for testing the runout or adjusting the ma-chine tool spindle. Runout accuracy taper to shaft ≤ 0,003 mm Delivery with measuring protocol Please order wooden box for storage seperately (see page 7) NL = useable measuring length
Artikel Nr. Bezeichnung A L D NL
article no. description mm mm mm mm
tb.ps040.001 PSC 40 x 25 x 179 169 179 25 160
tb.ps050.001 PSC 50 x 32 x 255 235 255 32 230
tb.ps063.001 PSC 63 x 40 x 322 300 322 40 300
tb.ps063.101 PSC 63 x 40 x 144 120 144 40 120
tb.ps080.001 PSC 80 x 40 x 330 300 330 40 300
PSC-Interface Applied for patent 1988 Market introduction 1990 >Capto< Polygonal taper interface with flange surface contact ISO 26623-1
Artikel Nr. Bezeichnung A L D NL
article no. description mm mm mm mm
tb.ha025.001 HSK-A 25 x 25 x 100 80 100 25 70
tb.ha032.001 HSK-A 32 x 25 x 200 180 200 25 170
tb.ha040.001 HSK-A 40 x 25 x 200 180 200 25 170
tb.ha050.001 HSK-A 50 x 32 x 346 320 346 32 300
tb.ha050.002 HSK-A 50 x 32 x 246 220 246 32 200
tb.ha063.001 HSK-A 63 x 40 x 346 320 346 40 300
tb.ha063.002 HSK-A 63 x 40 x 200 174 200 40 150
tb.ha080.001 HSK-A 80 x 40 x 346 320 346 40 300
tb.ha100.001 HSK-A 100 x 40 x 349 320 349 40 300
tb.ha100.002 HSK-A 100 x 50 x 349 320 349 40 300
tb.ha125.001 HSK-A 125 x 50 x 349 320 349 50 300
tb.ha125.002 HSK-A 125 x 40 x 349 320 349 40 300
Artikel Nr. Bezeichnung A L D NL
article no. description mm mm mm mm
tb.hc032.001 HSK-C 32 x 25 x 160 150 160 25 140
tb.hc040.001 HSK-C 40 x 25 x 160 150 160 25 140
tb.hc050.001 HSK-C 50 x 32 x 300 287,5 300 32 275
tb.hc063.001 HSK-C 63 x 40 x 300 287,5 300 40 275
tb.hc063.002 HSK-C 63 x 50 x 100 87,5 100 50 75
tb.hc080.001 HSK-C 80 x 40 x 300 284 300 40 275
tb.hc100.001 HSK-C 100 x 50 x 300 284 300 50 275
Artikel Nr. Bezeichnung A L D NL
article no. description mm mm mm mm
tb.hf063.001 HSK-F 63 x 40 x 250 224 250 40 200
tb.hf080.001 HSK-F 80 x 50 x 346 320 346 50 300
HSK-Interface Standard for rotating tool holders: DIN 69893-6 Form F
HSK-Interface Standard for rotating tool holders: DIN 69893-1 Form A ISO 12164-1 Style A
HSK-Interface Standard for rotating tool holders: DIN 69893-1 Form C ISO 12164-1 Style C
Artikel Nr. Bezeichnung A D NL G
article no. description mm mm mm mm
tb.bt030.001 MAS BT 30 x 32x 300 300 32 275 M12
tb.bt040.001 MAS BT 40 x 40 x 300 300 40 269 M16
tb.bt050.001 MAS BT 50 x 50 x 300 300 50 267 M24
Artikel Nr. Bezeichnung A L D NL
article no. description mm mm mm mm
tb.bt040.010 MAS BT 40 x 40 x 300 273 300 40 250
tb.bt040.011 MAS BT 40 x 40 x 150 123 150 40 100
tb.bt050.010 MAS BT 50 x 50 x 300 262 300 50 236
tb.bt050.011 MAS BT 50 x 50 x 200 162 200 50 136
Artikel Nr. Bezeichnung A L D NL
article no. description mm mm mm mm
tb.bb030.001 MAS BBT 30 x 32 x 300 278 300 32 252
tb.bb040.001 MAS BBT 40 x 40 x 300 273 300 40 250
tb.bb050.001 MAS BBT 50 x 50 x 300 262 300 50 236
Artikel Nr. Bezeichnung A D NL G
article no. description mm mm mm mm
tb.is030.001 SK 30 x 32 x 300 300 32 275 M12
tb.is040.001 SK 40 x 40 x 300 300 40 269 M16
tb.is040.002 SK 40 x 40 x 400 400 40 369 M16
tb.is045.001 SK 45 x 40 x 300 300 40 274 M20
tb.is050.001 SK 50 x 50 x 300 300 50 267 M24
tb.is050.002 SK 50 x 50 x 500 500 50 467 M24
tb.is050.003 SK 50 x 50 x 400 400 50 367 M24
tb.is060.001 SK 60 x 60 x 300 300 60 280 M30
Steilkegel / steep taper DIN 69871 part 1 / ISO 7388
ohne Flansch / without flange
Steilkegel /steep taper
JIS B 6339 (former MAS-BT) ohne Flansch / without flange
Steilkegel / steep taper JIS B 6339 (former MAS-BT)
mit Flansch / with flange
Steilkegel / steep taper JIS B 6339 (former MAS-BT)
mit Plananlage
with face contact
Steilkegel / steep taper
ASME B5.50 (ANSI/CAT) ohne Flansch / without flange
Artikel Nr. Bezeichnung A D NL G
article no. description mm mm mm UNC-28
tb.ca040.001 ANSI/CAT 40 x 40 x 300 300 40 269 0.625 - 11
tb.ca040.101 ANSI/CAT 40 x 40 x 18 " 457 40 426 0.625 - 11
tb.ca050.001 ANSI/CAT 50 x 50 x 300 300 50 267 1.00 - 8
tb.ca050.020 ANSI/CAT 50 x 40 x 14 " 365 40 332 1.00 - 8
tb.ca050.021 ANSI/CAT 50 x 50 x 600 600 50 567 1.00 - 8
tb.ca050.022 ANSI/CAT 50 x 60 x 800 800 60 767 1.00 - 8
tb.ca050.101 ANSI/CAT 50 x 50 x 18 " 457 50 424 1.00 - 8
Artikel Nr. Bezeichnung A L D NL
article no. description mm mm mm mm
tb.ts032.001 TS 32 x 32 x 70 70 70 32 60
tb.ts040.001 TS 40 x 40 x 80 80 80 40 70
tb.ts050.001 TS 50 x 50 x 100 100 100 50 90
tb.ts063.001 TS 63 x 63 x 120 120 120 63 100
tb.ts063.002 TS 63 x 50 x 346 320 346 50 300
tb.ts080.001 TS 80 x 80 x 120 120 120 80 100
tb.ts080.002 TS 80 x 50 x 346 320 346 50 300
tb.ts100.001 TS 100 x 100 x 120 120 120 100 100
tb.ts100.002 TS 100 x 50 x 349 320 349 500 300
Artikel Nr. Bezeichnung A NL D G
article no. description mm mm mm mm
tb.mc01.001 MT 1 x 18 x 200 200 185 18 M6
tb.mc02.001 MT 2 x 20 x 200 200 185 20 M10
tb.mc03.001 MT 3 x 25 x 200 200 195 25 M12
tb.mc05.001 MT 5 x 40 x 300 300 280 40 M20
Morsekegel / morse cone DIN 228 Form A / type A
TS / UTS / KM
track system ISO 26622-1
Modular taper interface with
ball
Artikel Nr. Bezeichnung A D d
article no. description mm mm mm
HSK-A
bea.ha032.010 HSK-A32 x 25 x 125 125 25 25
bea.ha040.010 HSK-A40 x 25 x 125 125 25 25
bea.ha050.010 HSK-A50 x 30 x 150 150 30 30
bea.ha063.001 HSK-A63 x 30 x 150 150 30 30
bea.ha080.001 HSK-A80 x 40 x 200 200 30 40
bea.ha100.001 HSK-A100 x 50 x 250 250 30 50
bea.ha125.001 HSK-A125 x 50 x 250 250 30 50
DIN 69871 / ISO 7388
bea.is040.001 ISO 40 x 30 x 150 150 30 30
bea.is050.001 ISO 50 x 40 x 150 150 30 40
JIS B 6339 / MAS 403 BT
bea.bt30.001 MAS BT 30 x 30 x 150 150 30 30
bea.bt40.001 MAS BT 40 x 30 x 150 150 30 30
bea.bt50.001 MAS BT 50 x 40 x 200 200 30 40
ANSI / CAT
bea.ca040.001 ANSI/CAT 40 x 30 x 150 150 30 30
bea.ca050.001 ANSI/CAT 50 x 40 x 150 150 30 40
Prüfdorn mit Kugel
Für 5-Achs-Maschinen zum Überprüfen des Drehmittelpunktes sowie
für die Kompensation von Positionsfehlern bei Schwenkkopfspindeln.
Genauigkeit Kegel zu Kugel ≤ 0,01 mm
Test arbor with ball
For 5 axis machine tools to test the rotation center point as well as for
compensation of positioning deviations of swivel head spindles.
Accuracy taper to ball ≤ 0,01 mm
Holzkisten zur optimalen, geschützten Aufbewahrung von Kontrolldornen:
Typ I: Liegende Aufbewahrung. Erhältlich von HSK 25 bis 63, PSC 32 bis 63, Steilkegel 30 und 40 sowie alle TS Größen.
Typ II: Stehende Aufbewahrung. Erhältlich von HSK 40 bis 100, PSC 32 bis 80 sowie Steilkegel 50.
Wooden Boxes for optimized and protected storage of test arbors:
Type I: Horizontal storage. Available for HSK 25 to 63, PSC 32 to 63, steep taper 30 to 40 and for all TS sizes.
Type II: Vertical storage. Available for HSK 40 to 100, PSC 32 to 80 and steep taper 50.
Service Cases for secure and protected transport of test bars:
Type I: 3 Bars of choice from HSK 25 to 63, PSC 32 to 63, steep taper 30 to 40.
Type II: 2 bars of choice from HSK 40 to 100, PSC 32 to 80, steep taper 50.
Wir führen auch weitere Lehren für Service und Wartung an Werkzeugmaschinen wie z.B.:
ClampControl zur elektronischen Messung von Einzugs– und Spannkräften sowie Einstell– und Ausrichtlehren für Maschinenspindeln, Werkzeugrevolver oder Werkzeugwechsler.
We also supply further gauges for service and maintenance of machine tools as there are: ClampControl for electronic measurement of pull back and clamping forces as well as setting and alignment gauges for machine spindles, tool turrets or tool changers.
Servicekoffer zum sicheren, geschützten Transport von Kontrolldornen:
Typ I: 3 Dorne nach Wahl aus HSK 25 bis 63, PSC 32 bis 63, Steilke-gel 30 und 40.
Typ II: 2 Dorne nach Wahl aus HSK 40 bis 100, PSC 32 bis 80 sowie Steilkegel 50.
clever clamping
Thomas Esswein Römerweg 33 D-73642 Welzheim [email protected]
www.tessma.de
Morse Taper Interface
Morse taper DIN 228
TS-Interface (known as KM)
Applied for patent1987
Market introduction 1989 >KM<
Modular taper interface with ball
track system ISO 26622-1
HSK-Interface
Standard for rotating tool holders:
DIN 69893-1 Form A and C
ISO 12164-1 Style A and C
DIN 69893-6 Form F
Standard for lathe tool holders:
ISO 12164-3 Form T “Turning”
PSC-Interface (known as Capto)
Applied for patent 1988
Market introduction 1990 >Capto<
Polygonal taper interface with flange
surface contact
ISO 26623-1
Steep Taper (SK)-Interface
Steep taper for automated tool change
DIN 69871 part 1: Form A
JIS B 6339 (before MAS-BT)
ASME B5.50 (ANSI/CAT)
01/1
5-1
-250