Clevis Pipe Hangers, Supports and Accessories · Clevis Pipe Hangers, Supports and ... this range...

158

Product overview • 2017 We reserve the right to change designs and technical specifications of our products.

Clevis Pipe Hangers, Supports and AccessoriesA comprehensive range of pipe hangers, supports and accessories, many of which are UL Listed and have FM approval. Most products in this range comply with MSS SP-58 and SP-69 and A-A-1192 A. Please enquire about items that are not specifi cally shown in this section.

9.

159

Clevis Hangers


9

Clevis Pipe Hangers, Supports and AccessoriesA comprehensive range of pipe hangers, supports and accessories, many of which are UL Listed and have FM approval. Most products in this range comply with MSS SP-58 and SP-69 and A-A-1192 A. Please enquire about items that are not specifi cally shown in this section.

9.

160


Zinc Coating• Electroplated Zinc (ASTM B633) This type of coating is recommended for indoor use in relatively dry areas. This process deposits a coating of zinc on the steel or iron by electrolysis from a bath of zinc salts. This coating is pure zinc and adheres to the steel or iron with a molecular bond. A maximum of 12 μm of zinc can be applied using this method.

• Pre-Galvanized Zinc (ASTM A653)This type of coating is suitable for extended exposure in dry or mildly corrosive atmospheres, but not generally recommended for outdoor use, or in industrial environments. This coating is also referred to as “mill galvanized” or “hot dip mill galvanized”. This process continuously rolls steel coils or sheets through molten zinc. The steel is then cut or slit to size. Coating thickness of .90 ounces per square foot of steel surface (referred to as G90) is used on Flamco’s Figures 310G and 310NFPA. Cut edges are not zinc coated, however, zinc near the uncoated steel becomes a sacrificial anode, which protects the bare areas after a short period of time.

• Hot Dip Galvanized (ASTM 123)This type of coating provides extended corrosion protection for steel and iron products exposed to extreme humidity commonly evident in outdoor exposure or in uncontrolled atmospheric conditions. This coating provides superior corrosion resistance to that of electroplating. The process calls for the steel or iron product to be completely immersed into a bath of molten zinc, which creates a metallurgical bond. The minimum coating thickness is 1.5 ounces per square foot per side (3 ounces per square foot of steel or iron). Caution should be taken when specifying Hot Dip Galvanizing on certain products. Products with threaded components should either have the threads protected from the galvanizing process or chase the threads subsequent to hot dipping. Products with critical size tolerances should account for the thickness of the coating.

Alternative Finishes

Primer Flamco offers Red Primer and Yellow Primer. Both offer a degree of protection from the elements. These coatings are also used in applications where painting of the metal is desired. EPA is restricting the use of certain primers. Consult Flamco for specific primer chemical components, as well as corrosive capabilities of specific primers.

Plastic CoatingVinyl coating of the metal prevents galvanic reaction between dissimilar metals, provides corrosion resistance, reduces noise, and can be used where glass or plastic pipe contact with metal is not desired.

Epoxy CoatingFlamco offers various epoxy finish es in both commercial and military grades. These finishes offer a high degree of corrosion resistance. Flamco provides COPPER-GARD finish for copper tubing installations. The finish provides superior corrosion protection and insulates against dissimilar metal contact, thus preventing electrolysis. The process applies a baked-on epoxy paint to steel stampings and iron castings. In the three step process, the parts are zinc plated to .0002” thick, an epoxy copper colored powder is then applied by an electrostatic method, and finally, the coated parts are baked at 180 ° for 20 minutes.

Copper PlatingThis coating is designed for copper tubing installations. The coating is intended to identify the product size only. This finish is not intended for corrosion resistance.

Chrome PlatingThis coating is intended to support chrome plated pipe and provides corrosion resistance for commercial installations such as hospitals, schools and prisons.

Flamco can offer alternative coatings for all products detailed in this chapter such as plastic, red and yellow oxide primer, epoxy, hot dip

galvanized, electro zinc, copper, COPPER-GARD, chrome and colour coordinated finishes. Specialized finishes may be available upon request.

161

Clevis Hangers


9CLEVIS HANGERS

CH - G Clevis Hangers

Type 11Standard, adjustable clevis hangers.• Material: Carbon steel *. • Finish: Electro-galvanized *.• Service: Designed for the suspension of non-insulated, stationary pipe lines.• Approvals: U.L. - U.L.C. listed (sizes 21/2" - 8")

FM approved (3/4" - 8").• Complies with: Federal Specification WW-H-171-E (Type# 1), A-A-1192 A (Type# 1)

Manufacturers‘ Standardization Society MSS SP-58 and SP-69 (Type# 1).• Notes: Upper locknut must be tightened securely to assure proper hanger performance. Stainless steel hangers are

recommended for applications where protection from corrosive environments is needed.

A

Pipe

E

FB

C

Type Ø Pipe Material size Dimensions Max. rec.

working load[lbs]

Weight[lbs]

OrderCode

Nom.["]

OD["]

Top["]

Bottom["]

Bolt["]

A["]

B["]

C["]

E **["]

F["]

CH-G 1/21/2 0.840 13ga x 7/8 13ga x 7/8 1/4 3/8 1 11/16 2 1/16 15/16 7/16 610 0.18 1 87000

CH-G 3/43/4 1.050 13ga x 7/8 13ga x 7/8 1/4 3/8 1 11/16 2 9/16 15/16 7/16 610 0.18 1 87001

CH-G 1 1 1.315 13ga x 7/8 13ga x 7/8 1/4 3/8 2 1/16 2 11/16 1 1/4 5/8 610 0.22 1 87002CH-G 1 1/4 1 1/4 1.660 13ga x 7/8 13ga x 7/8 1/4 3/8 2 1/2 3 3/16 1 11/16 7/8 610 0.26 1 87003CH-G 1 1/2 1 1/2 1.900 12ga x 7/8 12ga x 7/8 1/4 3/8 2 7/8 3 11/16 2 1/16 1 1/16 610 0.34 1 87004CH-G 2 2 2.375 12ga x 7/8 12ga x 7/8 1/4 3/8 3 5/16 4 7/16 2 1/2 1 1/4 610 0.38 1 87005CH-G 2 1/2 2 1/2 2.875 9ga x 1 3/16 10ga x 1 3/16 5/16 1/2 4 1/2 5 7/8 3 3/8 1 15/16 1130 0.86 1 87006CH-G 3 3 3.500 9ga x 1 3/16 10ga x 1 3/16 5/16 1/2 4 3/4 6 1/2 3 11/16 1 3/4 1130 0.96 1 87007CH-G 3 1/2 3 1/2 4.000 8ga x 1 3/16 10ga x 1 3/16 5/16 1/2 5 7/8 7 15/16 4 13/16 2 9/16 1130 1.14 1 87008CH-G 4 4 4.500 8ga x 1 3/16 10ga x 1 3/16 3/8 5/8 5 15/16 8 3/16 4 9/16 2 1/8 1430 1.26 1 87009CH-G 5 5 5.563 4ga x 1 1/4 8ga x 1 1/4 1/2 5/8 5 11/16 8 7/16 4 5/16 1 7/16 1430 2.04 1 87010CH-G 6 6 6.625 3ga x 1 1/2 8ga x 1 1/2 1/2 3/4 6 13/16 10 1/8 5 3/16 1 3/4 1940 2.80 1 87011CH-G 7 7 7.625 3ga x 1 1/2 8ga x 1 1/2 1/2 3/4 7 13/16 11 5/8 6 3/16 2 2000 3.24 1 87012CH-G 8 8 8.625 3ga x 1 3/4 8ga x 1 3/4 5/8 3/4 8 1/16 12 7/16 6 1/4 1 7/8 2000 4.46 1 87013CH-G 10 10 10.750 3/8 x 1 3/4 3ga x 1 3/4 3/4 7/8 10 15 7/16 8 2 1/4 3600 8.06 1 87014CH-G 12 12 12.750 3/8 x 2 3ga x 2 3/4 7/8 11 9/16 18 9 9/16 2 13/16 3800 10.34 1 87015CH-G 14 14 14.000 1/2 x 2 1/2 1/4 x 2 7/8 1 12 9/16 19 9/16 10 9/16 2 9/16 4200 14.80 1 87016CH-G 16 16 16.000 1/2 x 2 1/2 1/4 x 2 1/2 1 1 13 15/16 21 15/16 11 15/16 2 13/16 4600 21.00 1 87017CH-G 18 18 18.000 5/8 x 3 1/4 x 2 1/2 1 1 16 25 13 7/8 3 3/4 4800 24.40 1 87018CH-G 20 20 20.000 5/8 x 3 3/8 x 3 1 1/4 1 1/4 17 1/2 27 1/2 15 1/8 3 3/4 4800 47.00 1 87019CH-G 24 24 24.000 5/8 x 3 3/8 x 3 1 1/4 1 1/4 19 3/4 31 3/4 17 3/8 4 4800 54.00 1 87020CH-G 30 30 30.000 3/4 x 3 3/8 x 3 1 1/4 1 1/4 24 1/8 39 1/8 21 1/2 4 3/4 6000 69.50 1 87021

* Material 304 and 316 stainless steel and finishes such as plain, painted or hot dip galvanized are available upon request.** “E” dimension includes exposed rod threads beyond bottom of the hex nut. Exposed rod thread dimension is equal to the diameter of the rod used.

162


CH - E Clevis Hangers

Type 11xClevis hangers with extended bottom. • Material: Carbon steel. • Finish: Electro-galvanized *.• Service: Designed for the suspension of non-insulated, stationary pipe lines. The bottom section of the hanger is

elongated to allow for easier installation of insulation.• Complies with: Federal Specifications WW-H-171-E (Type# 1), A-A-1192 A (Type# 1)

Manufacturers‘ Standardization Society MSS SP-58 and SP-69 (Type# 1).• Notes: Upper locknut must be tightened securely to assure proper hanger performance.

A

Pipe

E

F

BC


working load[lbs]

Weight[lbs]

OrderCode

Nom.["]

OD["]

Top["]

Bottom["]

Bolt["]

A["]

B["]

C["]

E **["]

F["]

CH-E 1/21/2 0.840 13ga x 7/8 12ga x 7/8 1/4 3/8 3 3/4 4 3/16 2 15/16 7/16 610 0.30 1 87200

CH-E 3/43/4 1.050 13ga x 7/8 13ga x 7/8 1/4 3/8 3 3/4 4 3/16 2 15/16 7/16 610 0.33 1 87201

CH-E 1 1 1.315 13ga x 7/8 13ga x 7/8 1/4 3/8 4 1/8 4 3/4 3 5/16 5/8 610 0.34 1 87202CH-E 1 1/4 1 1/4 1.660 13ga x 7/8 13ga x 7/8 1/4 3/8 4 7/16 5 1/4 3 5/8 7/8 610 0.39 1 87203CH-E 1 1/2 1 1/2 1.900 12ga x 7/8 12ga x 7/8 1/4 3/8 4 3/4 5 3/4 3 15/16 1 1/16 610 0.47 1 87204CH-E 2 2 2.375 12ga x 7/8 12ga x 7/8 1/4 3/8 7 1/4 8 7/16 6 7/16 1 1/4 610 0.65 1 87205CH-E 2 1/2 2 1/2 2.875 9ga x 1 3/16 10ga x 1 3/16 5/16 1/2 8 13/16 10 3/16 7 3/4 1 15/16 1130 1.24 1 87206CH-E 3 3 3.500 9ga x 1 3/16 10ga x 1 3/16 5/16 1/2 9 10 3/4 7 15/16 1 3/4 1130 1.34 1 87207CH-E 4 4 4.500 8ga x 1 3/16 10ga x 1 3/16 3/8 5/8 10 1/8 12 3/8 8 13/16 2 1/8 1430 1.92 1 87208CH-E 5 5 5.563 4ga x 1 1/4 8ga x 1 1/4 1/2 5/8 9 7/8 12 9/16 8 7/16 1 7/16 1430 2.58 1 87209CH-E 6 6 6.625 3ga x 1 1/2 8ga x 1 1/2 1/2 3/4 10 7/8 14 1/8 9 1/4 1 3/4 1940 3.36 1 87210CH-E 8 8 8.625 3ga x 1 3/4 8ga x 1 3/4 5/8 3/4 12 1/4 16 9/16 10 7/16 1 7/8 2000 5.08 1 87211CH-E 10 10 10.750 3/8 x 1 3/4 3ga x 1 3/4 3/4 7/8 14 1/2 19 7/8 12 1/2 2 1/4 3600 9.08 1 87212CH-E 12 12 12.750 3/8 x 2 3ga x 2 3/4 7/8 15 7/8 22 1/4 13 7/8 2 13/16 3800 11.54 1 87213

* Plain finish available upon request.** “E” dimension includes exposed rod threads beyond bottom of the hex nut. Exposed rod thread dimension is equal to the diameter of the rod used.

163

Clevis Hangers


9CH - GL Clevis Hangers

Type 110Adjustable clevis hangers, lightweight.• Material: Carbon steel. • Finish: Electro-galvanized *.• Service: Designed for the suspension of light stationary pipe or conduit.• Complies with: Federal Specification WW-H-171-E (Type# 1), A-A-1192 A (Type# 1).

Manufacturers‘ Standardization Society MSS SP-58 and SP-69 (Type# 1). Galvanized and coated only.

• Notes: Conduit comes in various outside diameters. Verify outside diameter of conduit is equal to outside diameter of schedule 40 steel pipe.

A

Pipe

E

FB

C


working load[lbs]

Weight[lbs]

OrderCode

Nom.["]

OD["]

Top["]

Bottom["]

Bolt["]

A["]

B["]

C["]

E **["]

F["]

CH-GL 1/21/2 0.840 18ga x 7/8 18ga x 7/8 1/4 3/8 1 3/4 2 1/8 1 1/2 150 0.12 1 87250

CH-GL 3/43/4 1.050 18ga x 7/8 18ga x 7/8 1/4 3/8 1 3/16 2 5/16 1 1/16 1/2 250 0.12 1 87251

CH-GL 1 1 1.315 18ga x 7/8 18ga x 7/8 1/4 3/8 2 1/8 2 3/4 1 5/16 3/4 250 0.12 1 87252CH-GL 1 1/4 1 1/4 1.660 18ga x 7/8 18ga x 7/8 1/4 3/8 2 1/2 3 1/4 1 3/4 15/16 250 0.18 1 87253CH-GL 1 1/2 1 1/2 1.900 14ga x 7/8 16ga x 7/8 1/4 3/8 2 13/16 3 13/16 2 1/16 1 1/8 250 0.24 1 87254CH-GL 2 2 2.375 14ga x 7/8 16ga x 7/8 1/4 3/8 3 5/16 4 1/2 2 9/16 1 1/4 250 0.26 1 87255CH-GL 2 1/2 2 1/2 2.875 12ga x 1 3/16 14ga x 1 3/16 1/4 1/2 4 1/2 5 5/16 3 7/16 2 1/16 350 0.58 1 87256CH-GL 3 3 3.500 12ga x 1 3/16 14ga x 1 3/16 1/4 1/2 4 13/16 6 9/16 3 3/4 1 7/8 350 0.66 1 87257CH-GL 3 1/2 3 1/2 4.000 11ga x 1 3/16 14ga x 1 3/16 5/16 1/2 5 15/16 7 7/8 4 7/8 2 5/8 350 0.82 1 87258CH-GL 4 4 4.500 11ga x 1 3/16 14ga x 1 3/16 3/8 1/2 6 1/16 8 5/16 5 2 3/8 400 0.94 1 87259

* Plain or painted finish available upon request.** “E” dimension includes exposed rod threads beyond bottom of the hex nut. Exposed rod thread dimension is equal to the diameter of the rod used.

164


PIPE COVERS

CPS Pipe Covers

Type 167/168Pipe covering protection shield.• Material: Pre-galvanized carbon steel *. • Finish: Pre-galvanized.• Service: Designed for outside of foam or fiberglass insulation on stationary pipe lines (not designed for pipe rollers) to

prevent crushing of insulation without breaking the vapor barrier.• Complies with: Federal Specifications WW-H-171-E (Type# 41), A-A-1192 A (Type# 40)

Manufacturers‘ Standardization Society MSS SP-58 and SP-69 (Type# 40).

A

D

C

Type Size. No.shield

Dimensions Weight[lbs]

OrderCode

Length["]

Stock sizeC["]

Ø["]

Hanger size["]

CPS 0 x 8 0 8 24ga 1 7/8" 1 1/2" 0.17 1 87300CPS 1 x 8 1 8 24ga 2 3/8" 2" 0.21 1 87301CPS 2 x 8 2 8 24ga 2 7/8" 2 1/2" 0.25 1 87302CPS 3 x 8 3 8 18ga 3 1/2" 3" 0.60 1 87303CPS 4 x 8 4 8 18ga 4" 3 1/2" 0.63 1 87304CPS 5 x 8 5 8 18ga 4 1/2" 4" 0.73 1 87305CPS 6 x 8 6 8 18ga 5 5" 0.83 1 87306CPS 7 x 8 7 8 18ga 5 9/16" 5" 0.93 1 87307CPS 8 x 8 8 8 18ga 6 5/8" 6" 1.10 1 87308CPS 0 x 12 0 12 24ga 1 7/8" 1 1/2" 0.25 1 87330CPS 1 x 12 1 12 24ga 2 3/8" 2" 0.31 1 87331CPS 2 x 12 2 12 24ga 2 7/8" 2 1/2" 0.37 1 87332CPS 3 x 12 3 12 18ga 3 1/2" 3" 0.90 1 87333CPS 4 x 12 4 12 18ga 4" 3 1/2" 0.95 1 87334CPS 5 x 12 5 12 18ga 4 1/2" 4" 1.10 1 87335CPS 6 x 12 6 12 18ga 5 5" 1.25 1 87336CPS 7 x 12 7 12 18ga 5 9/16" 5" 1.40 1 87337CPS 8 x 12 8 12 18ga 6 5/8" 6" 1.65 1 87338CPS 9 x 12 9 12 18ga 7 5/8" 8" 1.90 1 87339CPS 10 x 12 10 12 18ga 8 5/8" 8" 2.10 1 87340CPS 13 x 12 13 12 18ga 9 5/8" 10" 2.35 1 87341CPS 14 x 12 14 12 18ga 10 3/4" 10" 2.65 1 87342CPS 15 x 12 15 12 18ga 11 3/4" 12" 2.95 1 87343CPS 16 x 12 16 12 18ga 12 3/4" 12" 3.15 1 87344CPS 17 x 12 17 12 16ga 14" 14" 4.45 1 87345CPS 18 x 12 18 12 16ga 15" 16" 4.46 1 87346CPS 19 x 12 19 12 16ga 16" 16" 4.90 1 87347CPS 20 x 12 20 12 16ga 17" 18" 5.15 1 87348CPS 21 x 12 21 12 16ga 18" 18" 5.50 1 87349CPS 22 x 12 22 12 16ga 19" 20" 5.70 1 87350CPS 23 x 12 23 12 16ga 20" 20" 6.35 1 87351CPS 24 x 12 24 12 16ga 21" 24" 6.45 1 87352CPS 25 x 12 25 12 16ga 22" 24" 6.60 1 87353CPS 26 x 12 26 12 16ga 23" 24" 7.00 1 87354CPS 27 x 12 27 12 16ga 24" 24" 7.85 1 87355CPS 28 x 12 28 12 16ga 26" 30" 7.90 1 87356CPS 29 x 12 29 12 16ga 27" 30" 8.05 1 87357CPS 30 x 12 30 12 16ga 28" 30" 8.60 1 87358

* 304 stainless steel also available upon request.

165

Clevis Hangers


9CPS Shield Size No. Selection

Find the correct CPS shield size number.• Based on tube size and insulation thickness.

Tubingsize

Insulation thickness(A)

1/2" 3/4" 1" 1 1/2" 2"1/2" 0 1 2 4 53/4" 0 1 2 4 61" 1 2 3 4 61 1/4" 1 2 3 5 71 1/2" 2 3 3 5 72" 3 4 4 6 82 1/2" 4 5 5 7 83" 5 6 6 8 93 1/2" 6 7 7 8 94" 7 7 8 9 105" 8 8 9 10 136" 9 9 10 13 14

CPS Shield Size No. Selection

Find the correct CPS shield size number.• Based on pipe size and insulation thickness.

Pipingsize

Insulation thickness(A)

1/2" 3/4" 1" 1 1/2" 2"1/2" 0 1 - -3/4" 1 1 2 4 61" 1 2 3 5 71 1/4" 2 3 3 6 71 1/2" 2 3 4 6 72" 3 4 5 7 82 1/2" 4 5 6 7 83" 5 6 7 8 93 1/2" - - 8 9 104" - - 8 9 105" - - 9 10 136" - - 10 13 148" - - 14 15 1610" - - 16 17 1812" - - 18 19 2014" - - 19 20 2116" - - 21 22 2318" - - 23 24 2520" - - 25 26 2724" - - 28 29 30

166


ROLLER HANGERS

RHA Roller Hanger

Type 272Adjustable roller hanger.• Material: Carbon steel yoke and crossbolt with cast iron roller• Finish: Electro-galvanized.*• Service: Designed for the suspension of pipe where longidtudinal movement of pipe may occur due to the expansion

and contraction, and where vertical adjustment may be necessary.• Complies with: Federal Specification WW-H-171-E (Type# 44), A-A-1192 A (Type# 43)

Manufactures' Standardization Society MSS SP-58 and SP-59 (Type# 43).

A

D

EB

L

C

Type Material size["]

Dimensions Max rec load[lbs]

Weight[lbs]

OrderCode

A["]

B["]

C["]

D["]

E**["]

L["]

RH-A 2 8ga x 1.25 1/2 3 3/8 1 9/16 2 7/8 2 1/4 5 5/8 150 1.14 1 87400RH-A 2 1/2 8ga x 1.25 1/2 3 15/16 1 7/8 3 1/4 2 13/16 6 1/2 225 1.47 1 87401RH-A 3 8ga x 1.25 1/2 4 5/16 2 1/8 3 13/16 3 3/16 7 3/16 310 1.62 1 87402RH-A 3 1/2 3ga x 1.50 1/2 4 5/8 2 1/2 4 5/16 3 7/16 7 15/16 390 2.76 1 87403RH-A 4 3ga x 1.50 5/8 4 13/16 2 13/16 4 7/8 3 3/8 8 1/2 475 3.16 1 87404RH-A 5 3ga x 2.00 5/8 5 3/4 3 3/8 5 7/8 4 5/16 9 15/16 685 4.62 1 87405RH-A 6 3ga x 2.00 3/4 6 3/8 3 15/16 7 4 5/8 11 1/4 780 6.08 1 87406RH-A 7 3ga x 2.00 3/4 6 5/16 4 1/2 8 4 9/16 11 5/8 680 7.59 1 87407RH-A 8 3/8 x 2.00 7/8 7 9/16 5 1/8 9 5 7/16 13 7/8 780 11.83 1 87408RH-A 10 1/2 x 2 7/8 8 3/4 6 1/4 11 1/8 6 5/8 16 1/4 965 11.83 1 87409RH-A 12 1/2 x 2 1/2 7/8 9 5/8 7 3/8 13 7 7/8 18 7/8 1200 22.50 1 87410RH-A 14 1/2 x 3 1 11 1/4 8 3/8 14 1/4 9 1/4 21 7/8 1200 33.00 1 87411RH-A 16 1/2 x 3 1 12 1/4 9 3/8 16 1/4 10 1/4 24 1/8 1200 46.00 1 87412RH-A 18 1/2 x 3 1 13 1/4 10 1/2 18 1/4 11 1/2 26 1/2 1400 50.50 1 87413RH-A 20 5/8 x 3 1 1/4 14 1/4 11 5/8 20 1/4 12 1/4 28 1/8 1600 65.00 1 87414

* Plain or painted finish available upon request.** “E” dimension includes exposed rod threads beyond bottom of the hex nut. Exposed rod thread dimension is equal to the diameter of the rod used.

167

Clevis Hangers


9RRH Roller Hanger

Type 277Adjustable two rod roller hanger.• Material: Carbon steel axle with cast iron roller and sockets ends.• Finish: Electro-galvanized.*• Service: Designed for the suspension of pipe where longidtudinal movement of pipe may occur due to the expansion,

and contraction, and where vertical adjustment is necessary.• Complies with: Federal Specification WW-H-171-E (Type# 44), A-A-1192 A (Type# 41)

Manufactures' Standardization Society MSS SP-58 and SP-59 (Type# 41).

A

C

L

R

BE

Type Pipe OD["]

Axle size["]


Weight[lbs]

OrderCode

A["]

B["]

C["]

E["]

L["]

R["]

RRH 2 2.375 3/8 3/8 1 9/16 4 3/8 2 3/16 5 5/8 2 7/8 600 0.76 1 87600RRH 2 1/2 2.875 1/2 1/2 1 7/8 5 1/8 2 5/8 6 1/2 3 1/8 670 1.19 1 87601RRH 3 3.5 1/2 1/2 2 1/8 5 5/8 2 7/8 7 3 3/4 700 1.39 1 87602RRH 3 1/2 4 1/2 1/2 2 1/2 5 7/8 3 1/4 7 1/4 3 7/8 750 1.50 1 87603RRH 4 4.5 1/2 1/2 2 13/16 7 3 13/16 8 9/16 4 3/4 750 2.11 1 87604RRH 5 5.563 5/8 5/8 3 3/8 8 1/8 4 3/8 9 3/4 5 3/4 750 2.57 1 87605RRH 6 6.625 3/4 3/4 3 15/16 9 3/4 4 15/16 11 5/8 6 7/8 1070 4.40 1 87606RRH 7 7.625 3/4 3/4 4 1/2 10 1/2 5 1/4 12 1/2 8 1100 5.16 1 87607RRH 8 8.625 7/8 7/8 5 1/8 12 1/8 6 3/8 14 1/4 8 7/8 1350 7.43 1 87608RRH 10 10.75 7/8 7/8 6 1/4 14 7 1/2 16 1/4 11 1750 9.17 1 87609RRH 12 12.75 7/8 7/8 7 5/16 15 3/4 8 9/16 18 13 2400 13.15 1 87610RRH 14 14 1 1/8 1 8 3/8 17 3/4 9 13/16 20 1/2 14 1/4 3130 18.75 1 87611RRH 16 16 1 1/4 1 9 1/2 20 9/16 10 15/16 23 3/8 16 7/8 3970 24.54 1 87612RRH 18 18 1 1/4 1 10 7/16 22 11 7/8 24 7/8 18 5/16 4200 27.20 1 87613RRH 20 20 1 1/2 1 1/4 11 1/2 24 13 3/8 27 20 1/4 4550 32.00 1 87614RRH 24 24 1 3/4 1 1/2 13 13/16 28 3/4 16 1/6 32 24 1/4 6160 54.00 1 87615RRH 30 30 1 3/4 1 1/2 17 1/4 35 5/8 19 5/8 39 3/4 30 1/4 7290 82.00 1 87616

* Painted or hot dip galvanized are available upon request.

168


ROLLER CHAIR

RC Roller Chair

Type 275Roller chair.• Material: Carbon steel chair and axle with cast iron roller• Finish: Electro-galvanized.*• Service: Designed for the support of pipe where longidtudinal movement of pipe may occur due to the

expansion and contraction, and where vertical adjustment is not necessary. May be bolted or welded to supporting member.

DE

F

B

C


Axle size["]


Weight[lbs]

OrderCode

B["]

C["]

D["]

E["]

F["]

RC 2 4ga x 1.25 3/8 1 9/16 1 3/8 1 1/4 4 1/4 3/8 390 0.94 1 87500RC 2 1/2 4ga X 1.25 1/2 1 7/8 1 5/8 1 1/4 4 7/8 3/4 390 1.18 1 87501RC 3 4ga X 1.25 1/2 2 1/8 1 3/4 2 5 11/32 3/4 390 1.32 1 87502RC 3 1/2

3/8 x 1.500 1/5 2 1/2 2 2 1/2 6 11/32 3/8 390 2.58 1 87503RC 4 3/8 x 1.500 1/2 2 13/16 2 5/16 2 7 11/32 1/2 950 2.94 1 87504RC 5 3/8 x 1.500 5/8 3 3/8 2 1/2 3 8 1/4 1/2 950 3.64 1 87505RC 6 3/8 x 2.00 3/4 3 15/16 2 3/4 3 1/8 9 1/2 1/2 950 5.72 1 87506RC 7 3/8 x 2.00 3/4 4 1/2 2 13/16 3 3/8 10 1/2 1350 6.98 1 87507RC 8 3/8 x 2.00 7/8 5 1/8 3 3 3/8 12 1/4 5/8 1350 8.16 1 87508RC 10 1/2 x 2 7/8 6 3/8 3 5/8 5 14 1/2 5/8 1730 11.96 1 87509RC 12 1/2 x2 7/8 7 1/2 4 1/8 6 16 1/4 5/8 2400 15.86 1 87510RC 14 1/2 x 2.50 1 1/8 8 3/8 4 11/26 6 1/2 18 3/4 3130 21.58 1 87511RC 16 1/2 x 3 1 1/4 9 3/8 5 3/8 8 1/4 21 3/4 3970 34.50 1 87512RC 18 1/2 x 3 1 1/4 10 7/16 6 9 1/4 22 7/8 3/4 4200 36.50 1 87513RC 20 1/2 x 3 1 1/4 11 5/8 6 1/2 10 1/4 25 1/4 3/4 4550 45.00 1 87514RC 24 5/8 x 4 1 1/2 14 7 7/8 12 1/4 30 7/8 6160 77.50 1 87515

* Material 304 and 316 stainless steel an dfinish such as plain, painted or hot dip galvanized are available upon request.

169

Clevis Hangers


9PIPE ROLL STANDS

RS Pipe Rol Stand

Type 279Pipe rol stand, carbon steel.• Material: Carbon steel chair and axle with cast iron roller.*• Finish: Electro-galvanized.*• Service: Designed for support of pipe where longidtudinal movement of pipe may occur due to the expansion and

contraction, and where vertical adjustment is not necessary.• Complies with: Federal Specification WW-H-171-E (Type# 45), A-A-1192 A (Type# 41)

Manufactures' Standardization Society MSS SP-58 and SP-69 (Type# 44).• Notes: Stainless roller chairs are recommended for applications where protection from corrosive environments is

needed.

A

DCH

J

B

EF

G

Type Dimensions Max rec load[lbs]

Weight[lbs]

OrderCode

A **["]

B["]

C["]

D["]

E ***["]

Dia.F ****

["]

Dia.G ******

["]

H["]

J["]

RS 2 1 3/4 8 3/8 6 4 3 11/16 9/16 1 3 3/8 6 3/8 390 5.08 1 87700RS 2 1/2 1 3/4 3 15/16 6 4 3 15/16 9/16 1 3 3/8 6 3/8 390 5.08 1 87700RS 3 1 3/4 8 3/8 6 4 4 1/4 9/16 1 3 3/8 6 3/8 390 5.08 1 87700RS 3 1/2 1 3/4 8 3/8 6 4 4 1/2 9/16 1 3 3/8 6 3/8 390 5.08 1 87700RS 4 2 9 7/8 6 4 1/4 5 9/16 1 4 3/4 7 7/8 650 6.31 1 87704RS 5 2 9 7/8 6 4 1/4 5 9/16 9/16 1 4 3/4 7 7/8 950 6.31 1 87704RS 6 2 9 7/8 6 4 1/4 6 1/16 9/16 1 4 3/4 7 7/8 950 6.31 1 87704RS 8 3 3/8 8 5/8 8 5 8 13/16 11/16 1 7 4 2100 13.65 1 87707RS 10 3 3/8 8 5/8 8 5 9 7/8 11/16 1 7 4 2100 13.65 1 87707RS 12 3 7/8 11 8 5 8 13/16 13/16 1 9 5 3/4 3075 21.00 1 87709RS 14 3 7/8 11 8 5 9 7/8 13/16 1 9 5 3/4 3075 21.00 1 87709RS 16 4 1/4 12 3/8 10 6 1/2 13 5/8 13/16 1 10 3/8 6 3/4 4980 34.23 1 87711RS 18 4 1/4 12 3/8 10 6 1/2 14 11/16 13/16 1 10 3/8 6 3/4 4980 34.23 1 87711RS 20 4 1/4 12 3/8 10 6 1/2 15 11/16 13/16 1 10 3/8 6 3/4 4980 34.23 1 87711RS 24 4 3/8 13 1/2 10 6 1/2 17 11/16 13 3/8 1 11 1/2 7 1/2 6100 40.00 1 87714RS 30 5 1/8 13 1/2 17 10 7 3/4 21 3/4 1 14 1/4 10 12000 71.32 1 87715RS 36 5 3/4 20 12 9 25 3/4 1 3/8 1 17 12 12000 147.00 1 87715RS 42 5 3/4 20 12 9 28 7/8 1 3/8 1 17 12 12000 147.00 1 87716

* Material 304 and 316 stainless steel and finish such as plain, painted or hot dip galvanized are available upon request.** Centre of axle to bottom of plate.*** Center of pipe to bottom of base plate.**** Two holes.***** Four holes.

170


RSA Pipe Rol Stand

Type 280Adjustable pipe rol stand, carbon steel, galvanized.• Material: Carbon steel chair and axle with cast iron roller.*• Finish: Galvanized.*• Service: Designed for support of pipe where longidtudinal movement of pipe may occur due to the expansion and

contraction, and where vertical adjustment is necessary.• Complies with: Federal Specification WW-H-171-E (Type# 47), A-A-1192 A (Type# 46)

Manufactures' Standardization Society MSS SP-58 and SP-69 (Type# 46).• Notes: Stainless steel roller chairs are recommended for applications where protection from corrosive environments

is needed.

F

E

D

BDA

C

G

Type Dimensions Max rec load[lbs]

Weight[lbs]

OrderCode

A["]

B["]

C min.**

["]

C max.**

["]

D ***["]

E ****["]

F["]

G *****["]

RS-A 2 6 7/8 6 4 3/4 5 5/8 3 7/8 1 1 1/2 390 11.00 1 87800RS-A 2 1/2 6 7/8 3 7/8 5 5 7/8 3 7/8 1 1 1/2 390 11.00 1 87800RS-A 3 6 7/8 6 5 5/16 6 9/16 3 7/8 1 1 1/2 390 11.00 1 87800RS-A 3 1/2 6 7/8 6 5 9/16 6 7/16 3 7/8 1 1 1/2 390 11.00 1 87800RS-A 4 8 1/2 6 6 3/16 7 7/16 5 1/8 1 1 1/2 950 13.10 1 87804RS-A 5 8 1/2 6 6 3/4 8 5 1/8 1 1 1/2 950 13.10 1 87804RS-A 6 8 1/2 6 7 1/4 8 1/2 5 1/8 1 1 1/2 950 13.10 1 87804RS-A 8 10 1/2 7 1/2 10 1/8 11 11/16 7 3/8 1 1 3/4 2100 29.00 1 87807RS-A 10 10 1/2 7 1/2 11 3/16 12 3/4 7 3/8 1 1 3/4 2100 29.00 1 87807RS-A 12 12 1/5 8 1/4 12 3/4 14 1/8 9 1/2 1 1 7/8 3075 40.00 1 87809RS-A 14 12 1/2 8 1/4 13 3/8 14 3/8 9 1/2 1 1 7/8 3075 40.00 1 87809RS-A 16 14 5/8 10 15 3/8 17 1/4 11 1/8 1 1 1 1/8 4980 63.84 1 87811RS-A 18 14 5/8 10 16 3/8 18 1/4 11 1/8 1 1 1 1/8 4980 63.84 1 87811RS-A 20 14 5/8 10 17 3/8 19 1/4 11 1/8 1 1 1 1/8 4980 63.84 1 87811RS-A 24 15 3/4 10 19 1/4 21 1/4 12 1/4 1 1 1 1/4 6100 71.00 1 87814RS-A 30 19 1/2 10 3/4 24 7/16 26 11/16 15 3/4 1 1 1/2 1 3/4 7500 125.28 1 87815RS-A 36 23 12 3/4 23 4/9 29 4/9 18 4/7 1 3/8 2 2 12000 202.00 1 87816RS-A 42 23 12 3/4 29 3/4 32 3/4 18 4/7 1 1/8 2 2 12000 202.00 1 87816

* Material 304 and 316 stainless steel and finish such as plain, painted or hot dip galvanized are available upon request.** Centre of pipe to bottom of base plate.*** Center to center of mounting holes in bottom plate.**** Mounting holes in bottom plate.***** Axle diameter.

171

Clevis Hangers


9PIPE ROLLER SUPPORTS

PRS Pipe Roller Support

Type 9100Pipe roller support, galvanized.• Material: Carbon steel chair base plate and axle with cast iron roller.*• Finish: Galvanized.*• Service: Designed to be mounted on slotted rail for the support of pipe where longidtudinal movement of pipe may

occur due to the expansion and contraction.• Complies with: Federal Specification WW-H-171-E (Type# 47), A-A-1192 A (Type# 46)

Manufactures' Standardization Society MSS SP-58 and SP-69 (Type# 46).• Notes: Stainless steel adjustable roller chair support are recommended for applications where protection from

corrosive environments is needed.

AE

BD

C



Weight[lbs]

OrderCode

A["]

B["]

C["]

D["]

E["]

PRS 2 1/4 X 1 5/8 1 7/16 6 3 11/64 7 5/8 9/16 390 177 1 87850PRS 2 1/2

1/4 X 1 5/8 7 5/8 6 3 27/64 7 5/8 9/16 390 177 1 87850PRS 3 1/4 X 1 5/8 1 7/16 6 3 47/64 7 5/8 9/16 390 177 1 87850PRS 3 1/2

1/4 X 1 5/8 1 7/16 6 3 63/64 7 5/8 9/16 390 177 1 87850PRS 4 1/4 X 1 5/8 1 7/16 6 13/16 4 13/64 8 1/2 9/16 600 231 1 87854PRS 5 1/4 X 1 5/8 1 7/16 6 13/16 4 47/64 8 1/2 9/16 600 231 1 87854PRS 6 1/4 X 1 5/8 1 7/16 6 13/16 5 17/64 8 1/2 9/16 600 231 1 87854PRS 8 1/4 X 1 5/8 1 13/16 8 9/16 7 10 1/4 9/16 800 542 1 87857PRS 10 1/4 X 1 5/8 1 13/16 8 9/16 8 1/16 10 1/4 9/16 800 542 1 87887PRS 12 3/8 X 2 2 7/16 12 9 27/32 14 1/4 9/16 1300 1040 1 87859PRS 14 3/8 X 2 2 7/16 12 10 15/32 14 1/4 13/16 1300 1040 1 87859PRS 16 3/8 X 2 2 5/8 13 11 7/8 15 1/4 13/16 2300 1508 1 87861PRS 18 3/8 X 2 2 5/8 13 12 7/8 15 1/4 13/16 2300 1508 1 87861PRS 20 3/8 X 2 2 5/8 13 13 7/8 15 1/4 13/16 2300 1508 1 87861

* Material 304 and 316 stainless steel and finish such as plain, painted or hot dip galvanized are available upon request.

172


PROTECTION SADDLES

CS Protection Saddles

Type 1900 - 1905Pipe covering protection saddles.• Material: Carbon steel• Finish: Plain*• Service: Designed for use on insulated high temperature pipe lines to protect insulation from damage and minimize

heat loss.• Complies with: Federal Specification WW-H-171-E (Type# 40A and 40B), A-A-1192 A (Type# 39A and 39B)

Manufactures' Standardization Society MSS SP-58 and SP-69 (Type# 39A and 39B).• Notes: All saddles are 12 inch long when side edges beveled in. Stainless steel and alloy saddles are available and

priced on aplication.CS 1: 1" Insulation 1900CS 2: 1" Insulation 1901CS 3: 1" Insulation 1902CS 4: 1" Insulation 1903CS 5: 1" Insulation 1904CS 6: 1" Insulation 1905

CD

Type Actual thickness

of covering["]

Hanger roller sizeuse with model

Center line of pipe to outside of

saddleC["]

Center line of pipe to center line

of rollD["]


of rollE["]

Max rec load[lbs]

Weight[lbs]

OrderCode

RCRRH

RH-A RSRS-A

CS 1 3/73/7 5 5 1/2 5 - 3 1/2 4 9/16 4 15/16 5 1/4 1203 0.96 1 88001

CS 2 3/43/4 3 3 1/2 2 - 3 1/2 2 1/8 2 5/8 2 7/8 1200 1.74 1 88002

CS 3 3/43/4 4 5 2 - 3 1/2 2 3/4 3 3/8 3 3/8 1200 2.60 1 88003

CS 1 1 1 2 1/2 3 2 - 3 1/2 1 13/16 2 1/4 2 7/16 1200 0.93 1 88011CS 2 1 1 3 4 2 - 3 1/2 2 7/16 2 15/16 3 1200 1.74 1 88012CS 3 1 1 4 5 2 - 3 1/2 2 7/8 3 1/2 3 1/2 1200 2.60 1 88013CS 1 1 1/4 1 1/4 2 1/2 3 2 - 3 1/2 1 15/16 2 9/16 1200 1.32 1 88021CS 2 1 1/4 1 1/4 3 1/2 5 2 - 3 1/2 2 9/16 3 1/8 3 3/16 1200 1.82 1 88022CS 3 1 1/4 2 1/16 5 5 2 - 3 1/2 3 11/16 3 11/16 3 11/16 1200 2.60 1 88023CS 1 1 1/2 1 3 3 1/2 2 - 3 1/2 2 1/8 2 5/8 2 11/16 1200 1.32 1 88031CS 2 1 1/2 1 1/2 3 1/2 5 2 - 3 1/2 2 11/16 3 1/4 3 5/16 1200 1.82 1 88032CS 3 1 1/2 2 5/16 5 6 4 - 6 6 7/16 4 1/8 3 7/8 1800 2.75 1 88033CS 4 1 1/2 2 13/16 7 7 4 - 6 3 13/16 4 5/8 4 1/2 1800 3.01 1 88034CS 1 2 1 1/16 3 1/2 4 2 - 3 1/2 2 7/16 3 3 1/16 1200 1.34 1 88041CS 2 2 1 9/16 4 5 2 - 3 1/2 2 7/8 3 1/2 3 9/16 1200 1.98 1 88042CS 3 2 2 1/8 5 6 4 - 6 3 11/16 4 3/8 4 3/16 1800 2.80 1 88043CS 4 2 2 5/8 7 7 4 - 6 3 15/16 4 3/4 4 3/4 1800 3.18 1 88044CS 5 2 3 1/8 8 8 4 - 6 4 11/16 5 1/2 5 1/4 1800 3.97 1 88045CS 1 2 1/2 1 1/16 3 1/2 5 2 - 3 1/2 2 11/16 3 1/4 3 5/16 1200 1.34 1 88051CS 2 2 1/2 1 7/8 5 6 4 - 6 3 3/4 4 1/8 3 15/16 1200 1.98 1 88052CS 3 2 1/2 2 5/16 6 7 4 - 6 3 15/16 4 5/8 4 1/2 1800 2.80 1 88053CS 4 2 1/2 2 7/8 7 7 4 - 6 4 7/16 5 1/4 5 1800 3.20 1 88054CS 5 2 1/2 3 3/8 8 10 4 - 6 4 15/16 5 3/4 5 1/2 1800 3.98 1 88055CS 1 3 1 4 5 2 - 3 1/2 2 15/16 3 1/2 3 9/16 1200 1.48 1 88061CS 2 3 1 9/16 5 6 4 - 6 3 1/2 4 3/16 4 1/4 1800 2.08 1 88062CS 3 3 2 1/16 7 7 4 - 6 4 1/8 4 7/8 4 11/16 1800 2.90 1 88063

173

Clevis Hangers


9Type Actual

thickness of covering

["]

Hanger roller sizeuse with model

Center line of pipe to outside of

saddleC["]


of rollD["]


of rollE["]

Max rec load[lbs]

Weight[lbs]

OrderCode

RCRRH

RH-A RSRS-A

CS 4 3 2 9/16 8 8 4 - 6 4 11/16 5 3/8 5 5/16 1800 3.01 1 88064CS 5 3 3 1/16 10 10 8 - 10 5 5 15/16 6 1/16 1800 4.49 1 88065CS 1 3 1/2 1 1/4 5 6 4 - 6 3 7/16 4 3 15/16 1200 1.48 1 88071CS 2 3 1/2 1 13/16 7 7 4 - 6 4 4 11/16 4 1/2 1800 2.08 1 88072CS 3 3 1/2 2 1/4 8 8 4 - 6 4 3/8 5 3/16 5 1800 2.90 1 88073CS 4 3 1/2 2 3/4 8 10 8 - 10 4 13/16 5 3/4 5 11/16 1800 3.43 1 88074CS 5 3 1/2 3 5/16 10 10 8 - 10 5 1/2 6 7/16 6 3/8 1800 4.49 1 88075CS 1 4 1 1/16 5 6 4 - 6 3 9/16 4 3/16 4 3/16 1800 1.58 1 88081CS 2 4 1 9/16 7 7 4 - 6 3 7/8 4 11/16 4 3/4 1800 2.14 1 88082CS 3 4 2 1/16 8 8 4 - 6 4 11/16 5 1/2 5 1/4 1800 2.95 1 88083CS 4 4 2 9/16 8 10 8 - 10 5 1/8 6 1/16 6 1800 3.43 1 88084CS 5 4 3 1/16 10 10 8 - 10 5 9/16 6 1/2 6 5/8 1800 4.49 1 88085CS 6 4 4 1/16 12 14 8 - 10 6 9/16 7 11/16 7 9/16 1800 6.09 1 88086CS 1 5 1 7 7 4 - 6 4 1/8 4 13/16 4 3/4 1800 2.62 1 88091CS 2 5 1 1/2 8 8 4 - 6 4 1/2 5 5/16 5 3/8 1800 3.30 1 88092CS 3 5 2 8 10 8 - 10 4 15/16 5 7/8 6 1/8 1800 3.45 1 88093CS 4 5 2 9/16 10 12 8 - 10 5 9/16 6 1/2 6 5/8 1800 6.85 1 88094CS 5 5 3 1/16 10 12 8 - 10 6 1/8 7 1/16 7 1/4 1800 4.49 1 88095CS 6 5 4 3/16 12 14 4 - 6 7 3/16 8 1/4 8 3/16 1800 9.06 1 88096CS 1 6 1 8 8 4 - 6 4 9/16 5 3/8 5 1/4 1800 3.82 1 88101CS 2 6 1 1/2 8 10 8 - 10 5 1/16 5 7/8 6 1800 4.28 1 88102CS 3 6 2 10 12 8 - 10 5 1/2 6 1/2 6 1/2 1800 5.40 1 88103CS 4 6 2 1/2 10 12 8 - 10 6 1/16 7 1/16 7 1/4 1800 6.85 1 88104CS 5 6 3 12 12 8 - 10 6 9/16 7 5/8 7 5/8 1800 7.69 1 88105CS 6 6 4 1/8 14 16 12 - 14 7 5/8 91/8 8 3/4 1800 10.24 1 88106CS 2 8 1 1/2 10 12 8 - 10 6 7 1/8 7 1/16 1800 5.82 1 88111CS 3 8 2 12 12 8 - 10 6 1/2 7 5/8 7 9/16 1800 6.41 1 88112CS 4 8 2 11/16 12 14 8 - 10 7 1/4 8 5/16 8 5/16 1800 7.21 1 88113CS 5 8 3 1/8 14 16 12 - 14 7 5/8 9 1/8 8 3/4 1800 9.14 1 88114CS 6 8 4 1/8 16 18 12 - 14 8 11/16 10 1/8 9 7/8 1800 10.24 1 88115CS 2 10 1 9/16 12 14 8 - 10 7 1/4 8 5/16 8 5/16 5000 6.66 1 88121CS 3 10 2 1/16 14 16 12 - 14 7 5/8 9 1/16 8 13/16 5000 8.57 1 88122CS 4 10 2 9/16 14 16 12 - 14 8 3/16 9 5/8 9 5/16 5000 8.91 1 88123CS 5 10 3 1/16 16 18 16 - 20 8 7/8 10 1/4 10 5000 11.10 1 88124CS 6 10 4 1/16 18 20 16 - 20 9 11/16 11 5/16 11 1/8 5000 14.10 1 88125CS 2 12 1 1/2 14 16 12 - 14 8 1/16 9 5/8 9 1/4 5000 7.61 1 88131CS 3 12 2 1/16 16 18 16 - 20 8 13/16 10 3/16 10 5000 8.73 1 88132CS 4 12 2 5/8 16 18 16 - 20 9 1/8 10 11/16 10 1/2 5000 9.69 1 88133CS 5 12 3 1/16 18 20 16 - 20 9 11/16 11 5/16 11 5000 11.38 1 88134CS 6 12 4 1/8 20 - 16 - 20 10 13/16 12 3/8 12 3/16 5000 14.20 1 88135CS 2 14 1 1/2 16 18 12 - 14 8 7/8 10 3/16 10 1/16 5000 7.67 1 88141CS 3 14 2 16 18 16 - 20 9 1/4 10 3/4 10 11/16 5000 9.43 1 88142CS 4 14 2 1/2 18 20 16 - 20 9 3/4 11 5/16 11 3/16 5000 9.69 1 88143CS 5 14 3 18 20 16 - 20 10 1/4 11 7/8 11 5/8 5000 11.82 1 88144CS 6 14 4 20 - 24 11 7/16 13 1/8 12 5/8 7200 18.48 1 88145CS 2 16 1 1/2 18 20 16 - 20 9 7/8 11 3/8 11 1/8 5000 8.35 1 88151CS 3 16 2 18 20 16 - 20 10 1/4 11 7/8 11 9/16 5000 10.00 1 88152CS 4 16 2 1/2 20 - 16 - 20 10 7/8 12 7/16 12 3/16 7200 14.62 1 88153CS 5 16 3 24 - 24 11 3/16 13 1/8 12 7/16 7200 18.17 1 88154CS 6 16 4 24 - 24 12 5/16 14 3/16 12 3/16 7200 21.80 1 88155CS 2 18 1 1/2 20 - 16 - 20 10 7/8 12 1/2 12 3/16 5000 8.92 1 88161CS 3 18 2 20 - 24 11 1/2 13 1/16 12 11/16 7200 13.19 1 88162CS 4 18 2 1/2 24 - 24 12 13 15/16 13 1/16 7200 16.89 1 88163CS 5 18 3 24 - 24 12 5/16 14 1/4 13 5/8 7200 18.20 1 88164CS 6 18 4 24 - 24 13 1/2 15 7/16 14 3/4 7200 21.95 1 88165CS 2 20 1 1/2 24 - 24 11 3/4 13 11/16 13 1/16 7200 13.76 1 88171CS 3 20 2 24 - 24 12 5/16 14 1/4 13 5/8 7200 14.98 1 88172CS 4 20 2 1/2 24 - 24 12 7/8 14 13/16 14 3/16 7200 16.79 1 88173CS 5 20 3 24 - 24 13 1/2 15 1/2 14 3/4 7200 18.40 1 88174CS 6 20 4 30 - 30 14 3/16 16 5/8 15 7/8 7200 22.83 1 88175CS 2 24 1 1/2 30 - 30 13 5/8 16 1/16 15 1/4 7200 16.05 1 88181CS 3 24 2 30 - 30 14 3/16 16 5/8 15 3/4 7200 17.62 1 88182CS 4 24 2 1/2 30 - 30 14 3/4 17 3/16 16 7/16 7200 18.75 1 88183CS 5 24 3 30 - 30 15 3/8 17 13/16 17 7200 19.72 1 88184CS 6 24 4 30 - 30 16 9/16 19 19 1/4 7200 23.14 1 88185

* Electro-galvaniezed finish available upon request.

174


STANDARD RISER CLAMPS

SRC Riser Clamps

Type 50Riser clamps, electro-gavanized• Material: Carbon steel.*• Finish: Electro-galvanized.*• Service: Designed for supporting and stabilizing vertical pipe runs.• Complies with:U.L. - U.L.C. listed (sizes 2" - 8").

Federal Specification WW-H-171-E (Type# 8), A-A-1192 A (Type# 8) Manufactures' Standardization Society MSS SP-58 and SP-69 (Type# 8).

• Notes: Plastic coated riser clamps are completely plastic coated with zinc plated hardware. The plastic coating prevents pipe from coming in contact with the clamp and is designed to reduce noise, vibration and prevent electrolysis between pipe and clamp. Stainless steel riser clamps are recommended for applications where protection from corrosive environments is needed.

AB

Type Ø Pipe Dimensions Max rec load[lbs]

Weight[lbs]

OrderCode

Nom.["]

OD["]

A["]

B["]

SRC 1/21/2 0.840 8 5/8 2 1/8 220 0.88 1 88201

SRC 3/43/4 1.050 8 13/16 2 5/16 220 0.92 1 88202

SRC 1/21/2 1.315 9 1/16 2 5/8 220 0.94 1 88203

SRC 1 1/4 1 1/4 1.660 9 7/16 2 15/16 250 1.00 1 88204SRC 1 1/2 1 1/2 1900 10 3 7/16 250 1.04 1 88205SRC 2 2 2.375 10 9/16 4 300 1.14 1 88206SRC 2 1/2 2 1/2 2.875 11 1/8 4 9/16 400 1.60 1 88207SRC 3 3 3.500 11 13/16 5 1/4 500 1.70 1 88208SRC 3 1/2 3 1/2 4.000 13 6 600 2.06 1 88209SRC 4 4 4.500 13 5/8 6 5/8 750 2.20 1 88210SRC 5 5 5.563 14 1/8 7 5/8 1500 3.40 1 88211SRC 6 6 6.625 15 3/8 8 7/8 1600 3.72 1 88212SRC 8 8 8.625 18 5/8 12 2500 7.22 1 88213SRC 10 10 10.750 21 14 1/2 2500 10.94 1 88214SRC 12 12 12.750 22.75 16.75 2700 16.10 1 88215SRC 14 14 14.000 24 16 7/8 2700 17.00 1 88216SRC 16 16 16.000 26 21 2900 29.16 1 88217SRC 18 18 18.000 28 23 1/8 2900 31.91 1 88218SRC 20 20 20.000 30 25 2900 35.00 1 88219SRC 24 24 24.000 36 30 2900 42.00 1 88220

* Material 304 and 316 stainless steel and finish such as plain, painted or hot dip galvanized are available upon request.

175


Date post:	13-Jul-2018
Category:	Documents
Upload:	vothuan
View:	273 times
Download:	3 times

Clevis Pipe Hangers, Supports and Accessories · Clevis Pipe Hangers, Supports and ... this range...

Documents