Date post: | 31-Mar-2018 |
Category: |
Documents |
Upload: | hoangthuan |
View: | 251 times |
Download: | 2 times |
CLI Reference Guide T2600G Series Switches
T2600G-18TS(TL-SG3216) / T2600G-28TS (TL-SG3424)
T2600G-52TS (TL-SG3452) / T2600G-28MPS (TL-SG3424P)
1910012087 REV2.2.0
April 2017
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered
trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make
any derivative such as translation, transformation, or adaptation without permission from
TP-Link Technologies Co., Ltd. Copyright © 2017 TP-Link Technologies Co., Ltd. All rights
reserved.
http://www.tp-link.com
I
CONTENTS
Preface ............................................................................................................................ 1
Chapter 1 Using the CLI ................................................................................................... 5
1.1 Accessing the CLI ..................................................................................................................................... 5
1.1.1 Logon by a console port ...................................................................................................... 5
1.1.2 Logon by Telnet ...................................................................................................................... 7
1.1.3 Logon by SSH ........................................................................................................................ 11
1.2 CLI Command Modes ............................................................................................................................ 16
1.3 Privilege Restrictions ............................................................................................................................. 19
1.4 Conventions .............................................................................................................................................. 19
1.4.1 Format Conventions ........................................................................................................... 19
1.4.2 Special Characters .............................................................................................................. 20
1.4.3 Parameter Format ................................................................................................................ 20
Chapter 2 User Interface .............................................................................................. 21
2.1 enable ............................................................................................................................................... 21
2.2 service password-encryption .................................................................................................. 21
2.3 enable password ........................................................................................................................... 22
2.4 enable secret ................................................................................................................................. 23
2.5 configure .......................................................................................................................................... 24
2.6 exit...................................................................................................................................................... 25
2.7 end ..................................................................................................................................................... 25
2.8 clipaging ........................................................................................................................................... 26
2.9 history ............................................................................................................................................... 26
2.10 history clear .................................................................................................................................... 27
Chapter 3 IEEE 802.1Q VLAN Commands ................................................................ 28
3.1 vlan ..................................................................................................................................................... 28
3.2 interface vlan .................................................................................................................................. 29
3.3 name .................................................................................................................................................. 29
3.4 switchport mode ........................................................................................................................... 30
3.5 switchport access vlan ............................................................................................................... 31
3.6 switchport trunk allowed vlan ................................................................................................... 31
3.7 switchport trunk allowed vlan all ............................................................................................. 32
3.8 switchport general allowed vlan .............................................................................................. 33
3.9 switchport pvid .............................................................................................................................. 34
II
3.10 show vlan summary...................................................................................................................... 34
3.11 show vlan brief ............................................................................................................................... 35
3.12 show vlan ......................................................................................................................................... 35
3.13 show interface switchport ......................................................................................................... 36
Chapter 4 MAC-based VLAN Commands ................................................................. 37
4.1 mac-vlan mac-address ............................................................................................................... 37
4.2 mac-vlan .......................................................................................................................................... 38
4.3 show mac-vlan ............................................................................................................................... 38
4.4 show mac-vlan interface ............................................................................................................ 39
Chapter 5 Protocol-based VLAN Commands ......................................................... 40
5.1 protocol-vlan template (For T2600G-18TS only) .............................................................. 40
5.2 protocol-vlan template (For other switches) ....................................................................... 41
5.3 protocol-vlan vlan ......................................................................................................................... 42
5.4 protocol-vlan group ..................................................................................................................... 43
5.5 show protocol-vlan template .................................................................................................... 43
5.6 show protocol-vlan vlan ............................................................................................................. 44
Chapter 6 VLAN-VPN Commands .............................................................................. 45
6.1 dot1q-tunnel ................................................................................................................................... 45
6.2 dot1q-tunnel tpid .......................................................................................................................... 45
6.3 dot1q-tunnel mapping ................................................................................................................ 46
6.4 switchport dot1q-tunnel missdrop ......................................................................................... 47
6.5 switchport dot1q-tunnel mapping .......................................................................................... 47
6.6 switchport dot1q-tunnel mode ................................................................................................ 48
6.7 show dot1q-tunnel ....................................................................................................................... 49
6.8 show dot1q-tunnel mapping ..................................................................................................... 50
6.9 show dot1q-tunnel interface .................................................................................................... 50
Chapter 7 Private VLAN Commands ......................................................................... 51
7.1 private-vlan primary ..................................................................................................................... 51
7.2 private-vlan community .............................................................................................................. 51
7.3 private-vlan isolated .................................................................................................................... 52
7.4 private-vlan association ............................................................................................................. 53
7.5 switchport private-vlan ............................................................................................................... 53
7.6 switchport private-vlan host-association ............................................................................ 54
7.7 switchport private-vlan mapping ............................................................................................ 55
7.8 show vlan private-vlan ................................................................................................................ 56
III
7.9 show vlan private-vlan interface .............................................................................................. 56
Chapter 8 L2PT Commands ......................................................................................... 58
8.1 l2protocol-tunnel .......................................................................................................................... 58
8.2 l2protocol-tunnel type ................................................................................................................ 58
8.3 show l2protocol-tunnel global ................................................................................................. 60
8.4 show l2protocol-tunnel interface ............................................................................................ 60
Chapter 9 GVRP Commands ........................................................................................ 62
9.1 gvrp .................................................................................................................................................... 62
9.2 gvrp (interface)............................................................................................................................... 62
9.3 gvrp registration ............................................................................................................................ 63
9.4 gvrp timer ........................................................................................................................................ 64
9.5 show gvrp interface ..................................................................................................................... 65
9.6 show gvrp global ........................................................................................................................... 66
Chapter 10 Voice VLAN Commands ............................................................................ 67
10.1 voice vlan ......................................................................................................................................... 67
10.2 voice vlan aging ............................................................................................................................. 67
10.3 voice vlan priority .......................................................................................................................... 68
10.4 voice vlan mac-address ............................................................................................................. 69
10.5 switchport voice vlan mode ...................................................................................................... 70
10.6 switchport voice vlan security ................................................................................................. 70
10.7 show voice vlan ............................................................................................................................. 71
10.8 show voice vlan oui ...................................................................................................................... 71
10.9 show voice vlan switchport ....................................................................................................... 72
Chapter 11 Etherchannel Commands ......................................................................... 73
11.1 channel-group ............................................................................................................................... 73
11.2 port-channel load-balance ........................................................................................................ 74
11.3 lacp system-priority ..................................................................................................................... 75
11.4 lacp port-priority ........................................................................................................................... 76
11.5 show etherchannel ....................................................................................................................... 76
11.6 show etherchannel load-balance ............................................................................................ 77
11.7 show lacp ......................................................................................................................................... 78
11.8 show lacp sys-id ............................................................................................................................ 78
Chapter 12 User Management Commands ................................................................ 80
12.1 user name (password) ................................................................................................................. 80
IV
12.2 user name (secret) ........................................................................................................................ 81
12.3 service password-recovery ...................................................................................................... 82
12.4 user access-control ip-based .................................................................................................. 83
12.5 user access-control mac-based ............................................................................................. 84
12.6 user access-control port-based ............................................................................................. 85
12.7 line ...................................................................................................................................................... 85
12.8 password ......................................................................................................................................... 86
12.9 login ................................................................................................................................................... 88
12.10 login local ......................................................................................................................................... 88
12.11 media-type rj45 ............................................................................................................................. 89
12.12 telnet ................................................................................................................................................. 90
12.13 serial_port baud-rate ................................................................................................................... 90
12.14 show password-recovery .......................................................................................................... 91
12.15 show user account-list................................................................................................................ 91
12.16 show user configuration ............................................................................................................. 92
12.17 show telnet-status........................................................................................................................ 92
Chapter 13 HTTP and HTTPS Commands .................................................................. 94
13.1 ip http server .................................................................................................................................. 94
13.2 ip http max-users (For T2600G-18TS only) ......................................................................... 95
13.3 ip http max-users (For other switches) ................................................................................. 96
13.4 ip http session timeout ............................................................................................................... 96
13.5 ip http secure-server ................................................................................................................... 97
13.6 ip http secure-protocol............................................................................................................... 98
13.7 ip http secure-ciphersuite ......................................................................................................... 98
13.8 ip http secure-max-users .......................................................................................................... 99
13.9 ip http secure-session timeout ............................................................................................. 100
13.10 ip http secure-server download certificate ...................................................................... 101
13.11 ip http secure-server download key ................................................................................... 102
13.12 show ip http configuration ...................................................................................................... 103
13.13 show ip http secure-server .................................................................................................... 103
Chapter 14 ARP Commands ......................................................................................... 104
14.1 arp ................................................................................................................................................... 104
14.2 clear arp-cache .......................................................................................................................... 105
14.3 arp timeout ................................................................................................................................... 105
14.4 show arp ........................................................................................................................................ 106
14.5 show ip arp (interface) .............................................................................................................. 106
V
14.6 show ip arp summary................................................................................................................ 107
Chapter 15 Binding Table Commands ....................................................................... 108
15.1 ip source binding ....................................................................................................................... 108
15.2 ip dhcp snooping ....................................................................................................................... 109
15.3 ip dhcp snooping vlan .............................................................................................................. 110
15.4 ip dhcp snooping information option .................................................................................. 111
15.5 ip dhcp snooping information strategy .............................................................................. 111
15.6 ip dhcp snooping information format ................................................................................. 112
15.7 ip dhcp snooping information remote-id ........................................................................... 113
15.8 ip dhcp snooping information circuit-id ............................................................................. 114
15.9 ip dhcp snooping trust ............................................................................................................. 115
15.10 ip dhcp snooping mac-verify ................................................................................................. 115
15.11 ip dhcp snooping limit rate ..................................................................................................... 116
15.12 ip dhcp snooping decline rate ............................................................................................... 117
15.13 show ip source binding ............................................................................................................ 118
15.14 show ip dhcp snooping ............................................................................................................ 118
15.15 show ip dhcp snooping interface ......................................................................................... 119
15.16 show ip dhcp snooping information interface ................................................................. 119
Chapter 16 IPv6 Binding Table Commands .............................................................. 121
16.1 ipv6 source binding ................................................................................................................... 121
16.2 ipv6 dhcp snooping .................................................................................................................. 122
16.3 ipv6 dhcp snooping vlan ......................................................................................................... 123
16.4 ipv6 dhcp snooping trust ........................................................................................................ 123
16.5 ipv6 nd snooping ....................................................................................................................... 124
16.6 ipv6 nd snooping vlan .............................................................................................................. 125
16.7 ipv6 nd snooping max-entries ............................................................................................... 125
16.8 show ipv6 source binding ....................................................................................................... 126
16.9 show ipv6 dhcp snooping ....................................................................................................... 127
16.10 show ipv6 dhcp snooping interface .................................................................................... 127
16.11 show ipv6 nd snooping ............................................................................................................ 128
16.12 show ipv6 nd snooping interface ......................................................................................... 128
Chapter 17 IP Verify Source Commands .................................................................. 130
17.1 ip verify source ........................................................................................................................... 130
17.2 show ip verify source ................................................................................................................ 131
17.3 show ip verify source interface ............................................................................................. 131
VI
Chapter 18 IPv6 Verify Source Commands ............................................................. 133
18.1 ipv6 verify source ...................................................................................................................... 133
18.2 show ipv6 verify source ........................................................................................................... 134
18.3 show ipv6 verify source interface ........................................................................................ 134
Chapter 19 ND Detection Commands ....................................................................... 136
19.1 ipv6 nd detection ....................................................................................................................... 136
19.2 ipv6 nd detection vlan .............................................................................................................. 136
19.3 ipv6 nd detection trust ............................................................................................................. 137
19.4 show ipv6 nd detection ........................................................................................................... 138
19.5 show ipv6 nd detection interface ......................................................................................... 138
Chapter 20 ARP Inspection Commands .................................................................... 140
20.1 ip arp inspection(global) .......................................................................................................... 140
20.2 ip arp inspection trust .............................................................................................................. 140
20.3 ip arp inspection(interface)..................................................................................................... 141
20.4 ip arp inspection limit-rate ...................................................................................................... 142
20.5 ip arp inspection recover ........................................................................................................ 143
20.6 show ip arp inspection ............................................................................................................. 143
20.7 show ip arp inspection interface .......................................................................................... 144
20.8 show ip arp inspection statistics .......................................................................................... 144
20.9 clear ip arp inspection statistics ........................................................................................... 145
Chapter 21 DoS Defend Commands .......................................................................... 146
21.1 ip dos-prevent ............................................................................................................................ 146
21.2 ip dos-prevent type................................................................................................................... 146
21.3 show ip dos-prevent ................................................................................................................. 148
Chapter 22 IEEE 802.1X Commands .......................................................................... 149
22.1 dot1x system-auth-control .................................................................................................... 149
22.2 dot1x handshake ....................................................................................................................... 150
22.3 dot1x auth-method ................................................................................................................... 150
22.4 dot1x accounting ....................................................................................................................... 151
22.5 dot1x vlan-assignment ............................................................................................................ 152
22.6 dot1x guest-vlan(global) .......................................................................................................... 153
22.7 dot1x quiet-period..................................................................................................................... 153
22.8 dot1x timeout supplicant-timeout ....................................................................................... 154
22.9 dot1x max-reauth-req .............................................................................................................. 155
22.10 dot1x .............................................................................................................................................. 156
VII
22.11 dot1x guest-vlan(interface) .................................................................................................... 156
22.12 dot1x mab .................................................................................................................................... 157
22.13 dot1x port-control ..................................................................................................................... 158
22.14 dot1x port-method .................................................................................................................... 159
22.15 show dot1x global ..................................................................................................................... 159
22.16 show dot1x interface ................................................................................................................ 160
Chapter 23 PPPoE ID-Insertion Commands ............................................................ 161
23.1 pppoe id-insertion(global)....................................................................................................... 161
23.2 pppoe circuit-id(interface) ...................................................................................................... 162
23.3 pppoe circuit-id type ................................................................................................................ 162
23.4 pppoe remote-id ........................................................................................................................ 163
23.5 show pppoe id-insertion global ............................................................................................ 164
23.6 show pppoe id-insertion interface ....................................................................................... 164
Chapter 24 System Log Commands .......................................................................... 166
24.1 logging buffer .............................................................................................................................. 166
24.2 logging buffer level .................................................................................................................... 166
24.3 logging file flash ......................................................................................................................... 167
24.4 logging file flash frequency .................................................................................................... 168
24.5 logging file flash level ............................................................................................................... 169
24.6 logging host index ..................................................................................................................... 169
24.7 logging console .......................................................................................................................... 170
24.8 logging console level ................................................................................................................ 171
24.9 logging monitor .......................................................................................................................... 172
24.10 logging monitor level ................................................................................................................ 172
24.11 clear logging ................................................................................................................................ 173
24.12 show logging local-config....................................................................................................... 174
24.13 show logging loghost ............................................................................................................... 174
24.14 show logging buffer .................................................................................................................. 175
24.15 show logging flash ..................................................................................................................... 175
Chapter 25 SSH Commands ......................................................................................... 177
25.1 ip ssh server ................................................................................................................................ 177
25.2 ip ssh version .............................................................................................................................. 177
25.3 ip ssh algorithm .......................................................................................................................... 178
25.4 ip ssh timeout .............................................................................................................................. 179
25.5 ip ssh max-client ........................................................................................................................ 179
25.6 ip ssh download .......................................................................................................................... 180
VIII
25.7 remove public-key ..................................................................................................................... 181
25.8 show ip ssh................................................................................................................................... 181
Chapter 26 MAC Address Commands ....................................................................... 183
26.1 mac address-table static ........................................................................................................ 183
26.2 mac address-table aging-time .............................................................................................. 184
26.3 mac address-table filtering .................................................................................................... 184
26.4 mac address-table notification ............................................................................................. 185
26.5 mac address-table max-mac-count ................................................................................... 186
26.6 mac address-table notification (interface) ........................................................................ 187
26.7 mac address-table security ................................................................................................... 188
26.8 show mac address-table ......................................................................................................... 189
26.9 clear mac address-table ......................................................................................................... 190
26.10 show mac address-table aging-time .................................................................................. 190
26.11 show mac address-table max-mac-count ........................................................................ 191
26.12 show mac address-table interface ...................................................................................... 191
26.13 show mac address-table count ............................................................................................ 192
26.14 show mac address-table address ....................................................................................... 193
26.15 show mac address-table vlan ................................................................................................ 193
26.16 show mac address-table notification ................................................................................. 194
26.17 show mac address-table security ........................................................................................ 194
Chapter 27 System Configuration Commands ....................................................... 196
27.1 system-time manual ................................................................................................................. 196
27.2 system-time ntp ......................................................................................................................... 196
27.3 system-time dst predefined .................................................................................................. 198
27.4 system-time dst date ............................................................................................................... 199
27.5 system-time dst recurring ...................................................................................................... 200
27.6 hostname ...................................................................................................................................... 201
27.7 location .......................................................................................................................................... 202
27.8 contact-info ................................................................................................................................. 202
27.9 ip address ..................................................................................................................................... 203
27.10 ip address-alloc .......................................................................................................................... 204
27.11 reset ............................................................................................................................................... 205
27.12 reboot ............................................................................................................................................ 205
27.13 reboot-schedule ........................................................................................................................ 206
27.14 copy running-config startup-config .................................................................................... 207
27.15 copy startup-config tftp .......................................................................................................... 207
IX
27.16 copy tftp startup-config .......................................................................................................... 208
27.17 boot application ......................................................................................................................... 209
27.18 remove backup-image ............................................................................................................. 209
27.19 firmware upgrade ....................................................................................................................... 210
27.20 boot autoinstall start ................................................................................................................. 211
27.21 boot autoinstall persistent-mode ........................................................................................ 211
27.22 boot autoinstall auto-save ...................................................................................................... 212
27.23 boot autoinstall auto-reboot .................................................................................................. 212
27.24 boot autoinstall retry-count ................................................................................................... 213
27.25 show boot autoinstall ............................................................................................................... 214
27.26 show boot autoinstall downloaded-config ....................................................................... 214
27.27 ping ................................................................................................................................................. 215
27.28 tracert ............................................................................................................................................ 216
27.29 show system-info ...................................................................................................................... 217
27.30 show system-info interface ................................................................................................... 217
27.31 show image-info ......................................................................................................................... 218
27.32 show boot ..................................................................................................................................... 218
27.33 show running-config ................................................................................................................. 219
27.34 show running-config | ............................................................................................................... 219
27.35 show startup-config ................................................................................................................. 220
27.36 show system-time ..................................................................................................................... 220
27.37 show system-time dst .............................................................................................................. 221
27.38 show system-time ntp ............................................................................................................. 221
27.39 show cable-diagnostics interface gigabitEthernet ........................................................ 222
27.40 show cable-diagnostics careful interface ......................................................................... 222
27.41 show cpu-utilization .................................................................................................................. 223
27.42 show memory-utilization ......................................................................................................... 223
Chapter 28 IPv6 Address Configuration Commands ............................................ 225
28.1 ipv6 enable ................................................................................................................................... 225
28.2 ipv6 address autoconfig.......................................................................................................... 225
28.3 ipv6 address link-local ............................................................................................................. 226
28.4 ipv6 address dhcp ..................................................................................................................... 227
28.5 ipv6 address ra ........................................................................................................................... 227
28.6 ipv6 address eui-64 .................................................................................................................. 228
28.7 ipv6 address ................................................................................................................................ 229
28.8 show ipv6 interface ................................................................................................................... 230
X
Chapter 29 Ethernet Configuration Commands ..................................................... 231
29.1 interface gigabitEthernet ........................................................................................................ 231
29.2 interface range gigabitEthernet............................................................................................ 231
29.3 description ................................................................................................................................... 232
29.4 shutdown ...................................................................................................................................... 233
29.5 flow-control ................................................................................................................................. 234
29.6 duplex ............................................................................................................................................ 234
29.7 jumbo ............................................................................................................................................. 235
29.8 jumbo-size .................................................................................................................................... 235
29.9 speed ............................................................................................................................................. 236
29.10 storm-control pps ..................................................................................................................... 237
29.11 storm-control .............................................................................................................................. 237
29.12 bandwidth ..................................................................................................................................... 238
29.13 clear counters ............................................................................................................................. 239
29.14 show interface status ............................................................................................................... 240
29.15 show interface counters ......................................................................................................... 240
29.16 show interface configuration ................................................................................................. 241
29.17 show storm-control .................................................................................................................. 242
29.18 show bandwidth ......................................................................................................................... 242
Chapter 30 QoS Commands ......................................................................................... 244
30.1 qos (For T2600G-18TS only) ................................................................................................. 244
30.2 qos (For other switches) .......................................................................................................... 245
30.3 qos cos .......................................................................................................................................... 245
30.4 qos dscp ....................................................................................................................................... 246
30.5 qos queue cos-map .................................................................................................................. 247
30.6 qos queue dscp-map (For T2600G-18TS only) ............................................................... 248
30.7 qos queue dscp-map (For other switches) ....................................................................... 249
30.8 qos queue mode ........................................................................................................................ 250
30.9 qos queue weight ...................................................................................................................... 251
30.10 show qos interface .................................................................................................................... 252
30.11 show qos cos-map .................................................................................................................... 253
30.12 show qos dscp-map ................................................................................................................. 253
30.13 show qos queue mode ............................................................................................................. 254
30.14 show qos status ......................................................................................................................... 254
Chapter 31 Port Mirror Commands ............................................................................ 255
31.1 monitor session destination interface................................................................................ 255
XI
31.2 monitor session source interface ........................................................................................ 256
31.3 show monitor session .............................................................................................................. 257
Chapter 32 Port Isolation Commands ....................................................................... 258
32.1 port isolation................................................................................................................................ 258
32.2 show port isolation interface ................................................................................................. 259
Chapter 33 Loopback Detection Commands .......................................................... 260
33.1 loopback-detection (global) ................................................................................................... 260
33.2 loopback-detection interval ................................................................................................... 260
33.3 loopback-detection recovery-time ..................................................................................... 261
33.4 loopback-detection (interface) ............................................................................................. 262
33.5 loopback-detection config process-mode ...................................................................... 262
33.6 loopback-detection config recovery-mode ..................................................................... 263
33.7 loopback-detection recover .................................................................................................. 264
33.8 show loopback-detection global.......................................................................................... 264
33.9 show loopback-detection interface .................................................................................... 265
Chapter 34 DDM Commands ....................................................................................... 266
34.1 ddm state enable ....................................................................................................................... 266
34.2 ddm shutdown ............................................................................................................................ 266
34.3 ddm temperature_threshold .................................................................................................. 267
34.4 ddm voltage_threshold ............................................................................................................ 268
34.5 ddm bias_current_threshold ................................................................................................. 269
34.6 ddm tx_power_threshold ........................................................................................................ 270
34.7 ddm rx_power_threshold ........................................................................................................ 271
34.8 show ddm configuration.......................................................................................................... 272
34.9 show ddm status ........................................................................................................................ 273
Chapter 35 ACL Commands ......................................................................................... 274
35.1 time-range .................................................................................................................................... 274
35.2 absolute ........................................................................................................................................ 274
35.3 periodic ......................................................................................................................................... 275
35.4 holiday ........................................................................................................................................... 276
35.5 holiday (global) ............................................................................................................................ 277
35.6 access-list create ...................................................................................................................... 277
35.7 mac access-list .......................................................................................................................... 278
35.8 access-list standard ................................................................................................................. 279
35.9 access-list extended ................................................................................................................ 280
XII
35.10 access-list combined ............................................................................................................... 281
35.11 access-list ipv6 .......................................................................................................................... 283
35.12 rule .................................................................................................................................................. 284
35.13 access-list policy name ........................................................................................................... 286
35.14 access-list policy action .......................................................................................................... 286
35.15 redirect interface ....................................................................................................................... 287
35.16 s-condition ................................................................................................................................... 288
35.17 s-mirror.......................................................................................................................................... 288
35.18 qos-remark .................................................................................................................................. 289
35.19 access-list bind acl (interface) .............................................................................................. 290
35.20 access-list bind acl (vlan) ........................................................................................................ 290
35.21 access-list bind (interface) ..................................................................................................... 291
35.22 access-list packet-content profile ...................................................................................... 292
35.23 access-list packet-content config ...................................................................................... 292
35.24 access-list bind (vlan) ............................................................................................................... 293
35.25 show access-list ........................................................................................................................ 294
35.26 show access-list status ........................................................................................................... 295
35.27 show access-list policy ........................................................................................................... 295
35.28 show access-list bind ............................................................................................................... 296
Chapter 36 MSTP Commands ...................................................................................... 297
36.1 debug spanning-tree ................................................................................................................ 297
36.2 spanning-tree (global) .............................................................................................................. 298
36.3 spanning-tree (interface) ........................................................................................................ 298
36.4 spanning-tree common-config ............................................................................................. 299
36.5 spanning-tree mode ................................................................................................................. 300
36.6 spanning-tree mst configuration ......................................................................................... 301
36.7 instance ......................................................................................................................................... 301
36.8 name ............................................................................................................................................... 302
36.9 revision .......................................................................................................................................... 303
36.10 spanning-tree mst instance ................................................................................................... 304
36.11 spanning-tree mst ..................................................................................................................... 304
36.12 spanning-tree priority .............................................................................................................. 305
36.13 spanning-tree timer .................................................................................................................. 306
36.14 spanning-tree hold-count ....................................................................................................... 307
36.15 spanning-tree max-hops ......................................................................................................... 307
36.16 spanning-tree bpdufilter ......................................................................................................... 308
36.17 spanning-tree bpduguard ....................................................................................................... 309
XIII
36.18 spanning-tree guard loop ....................................................................................................... 309
36.19 spanning-tree guard root ........................................................................................................ 310
36.20 spanning-tree guard tc ............................................................................................................ 311
36.21 spanning-tree mcheck ............................................................................................................. 311
36.22 show spanning-tree active ..................................................................................................... 312
36.23 show spanning-tree bridge .................................................................................................... 312
36.24 show spanning-tree interface ............................................................................................... 313
36.25 show spanning-tree interface-security ............................................................................. 314
36.26 show spanning-tree mst ......................................................................................................... 314
Chapter 37 Ethernet OAM Commands ...................................................................... 316
37.1 ethernet-oam .............................................................................................................................. 316
37.2 ethernet-oam mode .................................................................................................................. 316
37.3 ethernet-oam link-monitor symbol-period ....................................................................... 317
37.4 ethernet-oam link-monitor frame ........................................................................................ 318
37.5 ethernet-oam link-monitor frame-period .......................................................................... 319
37.6 ethernet-oam link-monitor frame-seconds...................................................................... 320
37.7 ethernet-oam remote-failure ................................................................................................. 321
37.8 ethernet-oam remote-loopback received-remote- loopback ................................... 322
37.9 ethernet-oam remote-loopback .......................................................................................... 323
37.10 clear ethernet-oam statistics ................................................................................................ 324
37.11 clear ethernet-oam event-log ............................................................................................... 324
37.12 show ethernet-oam configuration ....................................................................................... 325
37.13 show ethernet-oam event-log .............................................................................................. 326
37.14 show ethernet-oam statistics ............................................................................................... 326
37.15 show ethernet-oam status ..................................................................................................... 327
Chapter 38 DLDP Commands ...................................................................................... 328
38.1 dldp (global) ................................................................................................................................. 328
38.2 dldp interval ................................................................................................................................. 328
38.3 dldp shut-mode .......................................................................................................................... 329
38.4 dldp reset (global) ...................................................................................................................... 330
38.5 dldp(interface) ............................................................................................................................. 330
38.6 dldp reset (interface) ................................................................................................................ 331
38.7 show dldp ..................................................................................................................................... 331
38.8 show dldp interface................................................................................................................... 332
Chapter 39 IGMP Snooping Commands.................................................................... 333
39.1 ip igmp snooping (global) ........................................................................................................ 333
XIV
39.2 ip igmp snooping (interface) .................................................................................................. 333
39.3 ip igmp snooping rtime ............................................................................................................ 334
39.4 ip igmp snooping mtime .......................................................................................................... 335
39.5 ip igmp snooping report-suppression ................................................................................ 335
39.6 ip igmp snooping immediate-leave ..................................................................................... 336
39.7 ip igmp snooping drop-unknown ......................................................................................... 336
39.8 ip igmp snooping last-listener query-inteval .................................................................... 337
39.9 ip igmp snooping last-listener query-count ..................................................................... 338
39.10 ip igmp snooping vlan-config ................................................................................................ 338
39.11 ip igmp snooping vlan-config (router-port-forbidden) ................................................. 340
39.12 ip igmp snooping multi-vlan-config ..................................................................................... 341
39.13 ip igmp snooping multi-vlan-config (router-port-forbidden) ...................................... 342
39.14 ip igmp snooping multi-vlan-config (source-ip-replace) ............................................. 343
39.15 ip igmp snooping querier vlan ............................................................................................... 343
39.16 ip igmp snooping querier vlan (general query) ................................................................ 344
39.17 ip igmp snooping max-groups .............................................................................................. 345
39.18 ip igmp snooping authentication .......................................................................................... 346
39.19 ip igmp snooping accounting ................................................................................................ 347
39.20 ip igmp profile ............................................................................................................................. 347
39.21 deny ................................................................................................................................................ 348
39.22 permit ............................................................................................................................................. 349
39.23 range .............................................................................................................................................. 349
39.24 ip igmp filter ................................................................................................................................. 350
39.25 clear ip igmp snooping statistics ......................................................................................... 350
39.26 show ip igmp snooping ............................................................................................................ 351
39.27 show ip igmp snooping interface ......................................................................................... 351
39.28 show ip igmp snooping vlan ................................................................................................... 352
39.29 show ip igmp snooping multi-vlan ....................................................................................... 353
39.30 show ip igmp snooping groups ............................................................................................. 353
39.31 show ip igmp snooping querier ............................................................................................. 354
39.32 show ip igmp profile .................................................................................................................. 355
Chapter 40 MLD Snooping Commands ..................................................................... 356
40.1 ipv6 mld snooping (global) ...................................................................................................... 356
40.2 ipv6 mld snooping (interface) ................................................................................................ 356
40.3 ipv6 mld snooping rtime .......................................................................................................... 357
40.4 ipv6 mld snooping mtime ........................................................................................................ 357
40.5 ipv6 mld snooping report-suppression ............................................................................. 358
XV
40.6 ipv6 mld snooping immediate-leave ................................................................................... 359
40.7 ipv6 mld snooping drop-unknown ....................................................................................... 359
40.8 ipv6 mld snooping last-listener query-inteval ................................................................. 360
40.9 ipv6 mld snooping last-listener query-count ................................................................... 360
40.10 ipv6 mld snooping vlan-config .............................................................................................. 361
40.11 ip mld snooping vlan-config (router-port-forbidden) .................................................... 362
40.12 ipv6 mld snooping multi-vlan-config .................................................................................. 363
40.13 ipv6 mld snooping multi-vlan-config (router-port-forbidden).................................... 364
40.14 ipv6 mld snooping multi-vlan-config (source-ip-replace) ........................................... 365
40.15 ipv6 mld snooping querier vlan ............................................................................................. 366
40.16 ipv6 mld snooping querier vlan (general query) .............................................................. 366
40.17 ipv6 mld snooping max-groups ............................................................................................ 367
40.18 ipv6 mld profile ........................................................................................................................... 369
40.19 deny ................................................................................................................................................ 369
40.20 permit ............................................................................................................................................. 370
40.21 range .............................................................................................................................................. 370
40.22 ipv6 mld filter ............................................................................................................................... 371
40.23 clear ipv6 mld snooping statistics ....................................................................................... 371
40.24 show ipv6 mld snooping .......................................................................................................... 372
40.25 show ipv6 mld snooping interface ....................................................................................... 372
40.26 show ipv6 mld snooping vlan ................................................................................................. 373
40.27 show ipv6 mld snooping multi-vlan ..................................................................................... 374
40.28 show ipv6 mld snooping groups .......................................................................................... 374
40.29 show ipv6 mld snooping querier .......................................................................................... 375
40.30 show ipv6 mld profile ................................................................................................................ 375
Chapter 41 SNMP Commands ..................................................................................... 377
41.1 snmp-server ................................................................................................................................ 377
41.2 snmp-server view ...................................................................................................................... 377
41.3 snmp-server group ................................................................................................................... 378
41.4 snmp-server user ...................................................................................................................... 380
41.5 snmp-server community ......................................................................................................... 381
41.6 snmp-server host ...................................................................................................................... 382
41.7 snmp-server engineID ............................................................................................................. 384
41.8 snmp-server traps snmp ......................................................................................................... 384
41.9 snmp-server traps link-status ............................................................................................... 385
41.10 snmp-server traps ..................................................................................................................... 386
41.11 snmp-server traps ddm ........................................................................................................... 387
XVI
41.12 snmp-server traps vlan ............................................................................................................ 388
41.13 snmp-server traps security dhcp-snoop .......................................................................... 389
41.14 rmon history ................................................................................................................................ 390
41.15 rmon event ................................................................................................................................... 391
41.16 rmon alarm ................................................................................................................................... 392
41.17 rmon statistics ............................................................................................................................ 393
41.18 show snmp-server..................................................................................................................... 394
41.19 show snmp-server view ........................................................................................................... 395
41.20 show snmp-server group ........................................................................................................ 395
41.21 show snmp-server user ........................................................................................................... 395
41.22 show snmp-server community ............................................................................................. 396
41.23 show snmp-server host ........................................................................................................... 396
41.24 show snmp-server engineID .................................................................................................. 397
41.25 show rmon history ..................................................................................................................... 397
41.26 show rmon event ....................................................................................................................... 398
41.27 show rmon alarm ........................................................................................................................ 398
41.28 show rmon statistics ................................................................................................................ 399
Chapter 42 LLDP Commands ....................................................................................... 400
42.1 lldp................................................................................................................................................... 400
42.2 lldp forward_message .............................................................................................................. 400
42.3 lldp hold-multiplier ..................................................................................................................... 401
42.4 lldp timer ....................................................................................................................................... 402
42.5 lldp receive ................................................................................................................................... 403
42.6 lldp transmit ................................................................................................................................. 403
42.7 lldp snmp-trap ............................................................................................................................. 404
42.8 lldp tlv-select ............................................................................................................................... 405
42.9 lldp management address ...................................................................................................... 405
42.10 lldp med-fast-count .................................................................................................................. 406
42.11 lldp med-status ........................................................................................................................... 407
42.12 lldp med-tlv-select .................................................................................................................... 407
42.13 lldp med-location ....................................................................................................................... 408
42.14 show lldp ....................................................................................................................................... 409
42.15 show lldp interface .................................................................................................................... 410
42.16 show lldp local-information interface ................................................................................. 410
42.17 show lldp neighbor-information interface ......................................................................... 411
42.18 show lldp traffic interface ....................................................................................................... 411
XVII
Chapter 43 sFlow Commands ...................................................................................... 413
43.1 sflow address .............................................................................................................................. 413
43.2 sflow enable ................................................................................................................................. 414
43.3 sflow collector collector-ID .................................................................................................... 414
43.4 sflow sampler .............................................................................................................................. 415
43.5 show sflow global ...................................................................................................................... 416
43.6 show sflow collector ................................................................................................................. 417
43.7 show sflow sampler .................................................................................................................. 417
Chapter 44 Static Routes Commands ....................................................................... 418
44.1 interface vlan ............................................................................................................................... 418
44.2 interface loopback .................................................................................................................... 418
44.3 switchport .................................................................................................................................... 419
44.4 interface range port-channel ................................................................................................. 420
44.5 description ................................................................................................................................... 420
44.6 shutdown ...................................................................................................................................... 421
44.7 interface port-channel ............................................................................................................. 422
44.8 ip route .......................................................................................................................................... 422
44.9 ipv6 routing .................................................................................................................................. 423
44.10 ipv6 route ...................................................................................................................................... 424
44.11 show interface vlan ................................................................................................................... 424
44.12 show ip interface ........................................................................................................................ 425
44.13 show ip interface brief .............................................................................................................. 426
44.14 show ip route ............................................................................................................................... 426
44.15 show ip route specify ............................................................................................................... 427
44.16 show ip route summary ........................................................................................................... 428
44.17 show ipv6 interface ................................................................................................................... 428
44.18 show ipv6 route .......................................................................................................................... 429
44.19 show ipv6 route summary ...................................................................................................... 429
Chapter 45 SDM Template Commands ..................................................................... 431
45.1 sdm prefer .................................................................................................................................... 431
45.2 show sdm prefer ........................................................................................................................ 432
Chapter 46 AAA Commands ........................................................................................ 433
46.1 aaa enable .................................................................................................................................... 433
46.2 tacacas-server host .................................................................................................................. 434
46.3 show tacacs-server .................................................................................................................. 435
XVIII
46.4 radius-server host ..................................................................................................................... 435
46.5 show radius-server ................................................................................................................... 437
46.6 aaa group ...................................................................................................................................... 437
46.7 server ............................................................................................................................................. 438
46.8 show aaa group .......................................................................................................................... 439
46.9 aaa authentication login .......................................................................................................... 439
46.10 aaa authentication enable....................................................................................................... 440
46.11 aaa authentication dot1x default .......................................................................................... 441
46.12 aaa accounting dot1x default ................................................................................................ 442
46.13 show aaa authentication ......................................................................................................... 443
46.14 show aaa accounting ................................................................................................................ 443
46.15 line console .................................................................................................................................. 444
46.16 login authentication (console) ............................................................................................... 444
46.17 enable authentication (console) ........................................................................................... 445
46.18 line telnet ...................................................................................................................................... 446
46.19 login authentication (telnet) .................................................................................................... 446
46.20 line ssh ........................................................................................................................................... 447
46.21 login authentication (ssh) ........................................................................................................ 447
46.22 enable authentication (telnet) ................................................................................................ 448
46.23 enable authentication (ssh) .................................................................................................... 449
46.24 ip http login authentication ..................................................................................................... 450
46.25 ip http enable authentication ................................................................................................. 450
46.26 show aaa global .......................................................................................................................... 451
Chapter 47 DHCP Server Commands ........................................................................ 452
47.1 service dhcp server .................................................................................................................. 452
47.2 ip dhcp server extend-option capwap-ac-ip.................................................................... 452
47.3 ip dhcp server extend-option vendor-class-id ............................................................... 453
47.4 ip dhcp server exclude-address ........................................................................................... 454
47.5 ip dhcp server pool ................................................................................................................... 454
47.6 ip dhcp server ping timeout ................................................................................................... 455
47.7 ip dhcp server ping packets ................................................................................................... 456
47.8 network ......................................................................................................................................... 456
47.9 lease ............................................................................................................................................... 457
47.10 address hardware-address .................................................................................................... 458
47.11 address client-identifier .......................................................................................................... 458
47.12 default-gateway ......................................................................................................................... 459
47.13 dns-server .................................................................................................................................... 460
XIX
47.14 netbios-name-server ............................................................................................................... 461
47.15 netbios-node-type .................................................................................................................... 461
47.16 next-server ................................................................................................................................... 462
47.17 domain-name .............................................................................................................................. 463
47.18 bootfile .......................................................................................................................................... 463
47.19 show ip dhcp server status .................................................................................................... 464
47.20 show ip dhcp server statistics............................................................................................... 464
47.21 show ip dhcp server extend-option .................................................................................... 465
47.22 show ip dhcp server pool ........................................................................................................ 465
47.23 show ip dhcp server excluded-address ............................................................................ 466
47.24 show ip dhcp server manual-binding .................................................................................. 466
47.25 show ip dhcp server binding .................................................................................................. 467
47.26 clear ip dhcp server statistics ............................................................................................... 467
47.27 clear ip dhcp server binding ................................................................................................... 468
Chapter 48 DHCP Relay Commands .......................................................................... 469
48.1 service dhcp relay ..................................................................................................................... 469
48.2 ip helper-address....................................................................................................................... 469
48.3 ip dhcp relay information ........................................................................................................ 470
48.4 ip dhcp relay information policy ........................................................................................... 471
48.5 ip dhcp relay information format .......................................................................................... 471
48.6 ip dhcp relay information custom ........................................................................................ 472
48.7 ip dhcp relay information circuit-id ...................................................................................... 473
48.8 ip dhcp relay information remote-id .................................................................................... 473
48.9 ip dhcp relay default-interface .............................................................................................. 474
48.10 ip dhcp relay vlan ....................................................................................................................... 475
48.11 show ip dhcp relay ..................................................................................................................... 475
Chapter 49 PoE Commands ......................................................................................... 477
49.1 power inline consumption (global) ....................................................................................... 477
49.2 power inline disconnect-method ......................................................................................... 477
49.3 power profile ............................................................................................................................... 478
49.4 power time-range ...................................................................................................................... 479
49.5 power holiday .............................................................................................................................. 480
49.6 absolute ........................................................................................................................................ 481
49.7 periodic ......................................................................................................................................... 481
49.8 holiday ........................................................................................................................................... 482
49.9 power inline consumption (interface) ................................................................................. 483
XX
49.10 power inline priority ................................................................................................................... 484
49.11 power inline supply .................................................................................................................... 484
49.12 power inline profile .................................................................................................................... 485
49.13 power inline time-range ........................................................................................................... 486
49.14 show power inline ...................................................................................................................... 486
49.15 show power inline configuration interface ........................................................................ 487
49.16 show power inline information interface ........................................................................... 487
49.17 show power profile .................................................................................................................... 488
49.18 show power holiday .................................................................................................................. 488
49.19 show power time-range ........................................................................................................... 489
XXI
Preface
This Guide is intended for network administrator to provide referenced information about CLI (Command Line Interface). The device mentioned in this Guide stands for T2600G-18TS/ T2600G-28TS/ T2600G-52TS/ T2600G-28MPS JetStream Gigabit L2 Managed Switch without any explanation. The commands in this guilde apply to these models if not specially noted, and T2600G-28TS is taken as an example model in the example commands. Some models featured in this guide may be unavailable in your country or region. For local sales information, visit http://www.tp-link.com.
Overview of this Guide Chapter 1: Using the CLI
Provide information about how to use the CLI, CLI Command Modes, Security Levels and some Conventions.
Chapter 2: User Interface
Provide information about the commands used to switch between five CLI Command Modes.
Chapter 3: IEEE 802.1Q VLAN Commands
Provide information about the commands used for configuring IEEE 802.1Q VLAN.
Chapter 4: MAC-based VLAN Commands
Provide information about the commands used for configuring MAC-based VLAN.
Chapter 5: Protocol VLAN Commands
Provide information about the commands used for configuring Protocol VLAN.
Chapter 6: VLAN-VPN Commands
Provide information about the commands used for configuring VLAN-VPN (Virtual Private Network) function.
Chapter 7: Private VLAN Commands
Provide information about the commands used for configuring Private VLAN.
Chapter 8: L2PT Commands
Provide information about the commands used for configuring L2PT (Layer 2 Portocol Tunneling).
Chapter 9: GVRP Commands
Provide information about the commands used for configuring GVRP (GARP VLAN registration protocol).
Chapter 10: Voice VLAN Commands
Provide information about the commands used for configuring Voice VLAN.
1
Chapter 11: Etherchannel Commands
Provide information about the commands used for configuring LAG (Link Aggregation Group) and LACP (Link Aggregation Control Protocol).
Chapter 12: User Management Commands
Provide information about the commands used for user management.
Chapter 13: HTTP and HTTPS Commands
Provide information about the commands used for configuring the HTTP and HTTPS logon.
Chapter 14: ARP Commands
Provide information about the commands used for configuring the ARP (Address Resolution Protocol) functions.
Chapter 15: Binding Table Commands
Provide information about the commands used for binding the IP address, MAC address, VLAN and the connected Port number of the Host together.
Chapter 16: IPv6 Binding Table Commands
Provide information about the commands used for binding the IPv6 address, MAC address, VLAN and the connected Port number of the Host together.
Chapter 17: IP Verify Source Commands
Provide information about the commands used for guarding the IP Source by filtering the IP packets based on the IP-MAC Binding entries.
Chapter 18: IPv6 Verify Source Commands
Provide information about the commands used for guarding the IPv6 Source by filtering the IP packets based on the IP-MAC Binding entries.
Chapter 19: ND Detection Commands
Provide information about the commands used for congifuring ND detection.
Chapter 20: ARP Inspection Commands
Provide information about the commands used for protecting the switch from the ARP cheating or ARP Attack.
Chapter 21: DoS Defend Command
Provide information about the commands used for DoS defend and detecting the DoS attack.
Chapter 22: IEEE 802.1X Commands
Provide information about the commands used for configuring IEEE 802.1X function.
Chapter 23 PPPoE ID Insertion Commands
Provide information about the commands used for configuring PPPoE ID Insertion.
Chapter 24: System Log Commands
Provide information about the commands used for configuring system log.
2
Chapter 25: SSH Commands
Provide information about the commands used for configuring and managing SSH (Security Shell).
Chapter 26: MAC Address Commands
Provide information about the commands used for Address configuration.
Chapter 27: System Configuration Commands
Provide information about the commands used for configuring the System information and System IP, reboot and reset the switch, upgrade the switch system and commands used for cable test.
Chapter 28: IPv6 Address Configuration Commands
Provide information about the commands used for configuring the System IPv6 addresses.
Chapter 29: Ethernet Configuration Commands
Provide information about the commands used for configuring the Bandwidth Control, Negotiation Mode, and Storm Control for enthernet ports.
Chapter 30: QoS Commands
Provide information about the commands used for configuring the QoS function.
Chapter 31: Port Mirror Commands
Provide information about the commands used for configuring the Port Mirror function.
Chapter 32: Port Isolation Commands
Provide information about the commands used for configuring Port Isolation function.
Chapter 33: Loopback Detection Commands
Provide information about the commands used for configuring the Loopback Detection function.
Chapter 34: DDM Commands
Provide information about the commands used for DDM (Digtal Diagnostic Monitoring) function.
Chapter 35: ACL Commands
Provide information about the commands used for configuring the ACL (Access Control List).
Chapter 36: MSTP Commands
Provide information about the commands used for configuring the MSTP (Multiple Spanning Tree Protocol).
Chapter 37 Ethernet OAM Commands
Provide information about the commands used for configuring the Ethernet OAM (Operation, Administration, and Maintenance) function.
3
Chapter 38: DLDP Commands
Provide information about the commands used for configuring the DLDP (Device Link Detection Protocol).
Chapter 39: IGMP Snooping Commands
Provide information about the commands used for configuring the IGMP Snooping (Internet Group Management Protocol Snooping).
Chapter 40: MLD Snooping Commands
Provide information about the commands used for configuring the MLD Snooping (Multicast Listener Discovery Snooping).
Chapter 41: SNMP Commands
Provide information about the commands used for configuring the SNMP (Simple Network Management Protocol) functions.
Chapter 42: LLDP Commands
Provide information about the commands used for configuring LLDP function.
Chapter 43: sFlow Commands
Provide information about the commands used for configuring the Sampled Flow function.
Chapter 44: Static Routes Commands
Provide information about the commands used for configuring the Static Route function.
Chapter 45: SDM Template Commands
Provide information about the commands used for configuring the SDM templates.
Chapter 46: AAA Commands
Provide information about the commands used for configuring AAA (authentication, authorization and accounting).
Chapter 47: DHCP Server Commands
Provide information about the commands used for configuring the DHCP Server function.
Chapter 48: DHCP Relay Commands
Provide information about the commands used for configuring the DHCP Relay function.
Chapter 49: PoE Commands(For T2600G-28MPS only)
Provide information about the commands used for configuring PoE function.
4
Chapter 1 Using the CLI
1.1 Accessing the CLI
You can log on to the switch and access the CLI by the following three methods:
1. Log on to the switch by the console port on the switch.
2. Log on to the switch remotely by a Telnet connection through an Ethernet port.
3. Log on to the switch remotely by an SSH connection through an Ethernet port.
1.1.1 Logon by a console port
Console Port The switch has two console ports: an RJ-45 console port and a Micro-USB console port. Console output is active on devices connected to both console ports, but console input is only active on one console port at a time.
The Micro-USB connector takes precedence over the RJ-45 connector. When the switch detects a valid connection on the Micro-USB console port, input from the RJ-45 console port is immediately disabled, and input from the Micro-USB console port is enabled. Removing the Micro-USB connection immediately reenables input from the RJ-45 console connection.
USB Console Driver
If you are using the USB port on the MAC OS X or Linux OS for console connection, there is no need to run a USB driver.
If you are using the switch’s Micro-USB console port with the USB port of a Windows PC, a driver for the USB port is required. The USB driver is provided on the resource CD. Follow the InstallSheild Wizard to accomplish the installation.
The TP-Link USB Console Driver supports the following Windows operating systems:
32-bit Windows XP SP3
64-bit Windows XP
32-bit Windows Vista
64-bit Windows Vista
32-bit Windows 7
64-bit Windows 7
32-bit Windows 8
5
64-bit Windows 8
32-bit Windows 8.1
64-bit Windows 8.1
After the TP-Link USB Console Driver is installed, the PC’s USB port will act as RS-232 serial port when the PC’s USB port is connected to the switch’s Micro-USB console port. And the PC’s USB port will act as standard USB port when the PC’s USB port is unplugged from the switch.
Logon
Take the following steps to log on to the switch by the console port.
1. Connect the PCs or Terminals to the console port on the switch by the provided cable.
2. Start the terminal emulation program (such as the HyperTerminal) on the PC.
3. Specify the connection COM port in the terminal emulation program. If the Micro-USB Console port is used, you can view which port is assigned to the USB serial port in the following path:
Control Panel -> Hardware and Sound -> Device Manager -> Ports ->USB Serial Port.
Figure 1-1 USB Serial Port Number
4. Configure the terminal emulation program or the terminal to use the following settings:
Baud rate: 38400 bps
Data bits: 8
Parity: none
Stop bits: 1
Flow control: none
6
5. The DOS prompt ”T2600G-28TS>” will appear after pressing the Enter button as shown in Figure 1-2. It indicates that you can use the CLI now.
Figure 1-2 Log in the Switch
1.1.2 Logon by Telnet
For Telnet connection, you should also configure the Telnet login mode and login authentication information through console connection.
Telnet login has the following two modes. You can choose one according to your needs:
Login local Mode: It requires username and password, which are both admin by default.
Login Mode: It doesn’t require username and password, but a connection password is required.
Before Telnet login, you are required to configure Telnet login mode and login authentication information through console connection.
7
Login Local Mode
Firstly, configure the Telnet login mode as “login local” in the prompted DOS screen shown in Figure 1-3.
Figure 1-3 Configure login local mode
Now, you can logon by Telnet in login local mode.
1. Make sure the switch and the PC are in the same LAN. Click Start and type in cmd in the Search programs and files window and press the Enter button.
Figure 1-4 Run Window
2. Type telnet 192.168.0.1 in the command prompt shown as Figure 1-5, and press the Enter button.
Figure 1-5 Connecting to the Switch
8
3. Type the default user name and password (both of them are admin), then press the Enter button so as to enter User EXEC Mode.
Figure 1-6 Enter into the User EXEC Mode
4. Type enable command to enter Privileged EXEC Mode.
Figure 1-7 Enter into the Priviledged EXEC Mode
Now you can manage your switch with CLI commands through Telnet connection.
Login Mode
Firstly configure the Telnet login mode as “login” and the connection password as 456 in the prompted DOS screen shown in Figure 1-8.
Figure 1-8 Configure login mode
9
Now, you can logon by Telnet in login mode:
1. Make sure the switch and the PC are in the same LAN. Click Start and type in cmd in the Search programs and files window and press the Enter button.
Figure 1-9 Run Window
2. Type telnet 192.168.0.1 in the command prompt shown as Figure 1-10, and press the Enter button.
Figure 1-10 Connecting to the Switch
3. You are prompted to enter the connection password 456 you have set through Console port connection, and then you are in User EXEC Mode.
Figure 1-11 Enter into the User EXEC Mode
10
4. Type enable command to enter Privileged EXEC Mode.
Figure 1-12 Enter into the Privileged EXEC Mode
Now you can manage your switch with CLI commands through Telnet connection.
Note:
You can refer to Chapter 11 User Management Commands for detailed commands information of the Telnet connection configuration.
1.1.3 Logon by SSH
To log on by SSH, a Putty client software is recommended. There are two authentication modes to set up an SSH connection:
Password Authentication Mode: It requires username and password, which are both admin by default.
Key Authentication Mode: It requires a public key for the switch and a private key for the SSH client software. You can generate the public key and the private key through Putty Key Generator.
Note:
Before SSH login, please follow the steps shown in Figure 1-13 to enable the SSH function through Telnet connection.
Figure 1-13 Enable SSH function
11
Password Authentication Mode
1. Open the software to log on to the interface of PuTTY. Enter the IP address of the switch into Host Name field; keep the default value 22 in the Port field; select SSH as the Connection type.
Figure 1-14 SSH Connection Config
2. Click the Open button in the above figure to log on to the switch. Enter the login user name and password to log on the switch, and then enter enable to enter Privileged EXEC Mode, so you can continue to configure the switch.
Figure 1-15 Log on the Switch
12
Key Authentication Mode
1. Select the key type and key length, and generate SSH key.
Figure 1-16 Generate SSH Key
Note:
1. The key length is in the range of 512 to 3072 bits. 2. During the key generation, randomly moving the mouse quickly can accelerate the key
generation.
13
2. After the key is successfully generated, please save the public key and private key to a TFTP server.
Figure 1-17 Save the Generated Key
3. Log on to the switch by Telnet and download the public key file from the TFTP server to the switch, as the following figure shows:
Figure 1-18 Download the Public Key
14
Note:
1. The key type should accord with the type of the key file. 2. The SSH key downloading can not be interrupted.
4. After the public key is downloaded, please log on to the interface of PuTTY and enter the IP address for login.
Figure 1-19 SSH Connection Config
15
5. Click Browse to download the private key file to SSH client software and click Open.
Figure 1-20 Download the Private Key
6. After successful authentication, please enter the login user name. If you log on to the switch without entering password, it indicates that the key has been successfully downloaded.
Figure 1-21 Log on the Switch
1.2 CLI Command Modes
The CLI is divided into different command modes: User EXEC Mode, Privileged EXEC Mode, Global Configuration Mode, Interface Configuration Mode and VLAN Configuration Mode.
16
Interface Configuration Mode can also be divided into Interface Ethernet, Interface link-aggregation and some other modes, which is shown as the following diagram.
The following table gives detailed information about the Accessing path, Prompt of each mode and how to exit the current mode and access the next mode.
Mode Accessing Path Prompt Logout or Access the next
mode
User EXEC
Mode
Primary mode once
it is connected with
the switch.
T2600G-28TS>
Use the exit command to
disconnect the switch.
Use the enable command to
access Privileged EXEC mode.
Privileged
EXEC Mode
Use the enable
command to enter
this mode from User
EXEC mode.
T2600G-28TS#
Enter the disable or the exit
command to return to User
EXEC mode.
Enter configure command to
access Global Configuration
mode.
Global Configuration Mode
Use the configure
command to enter
this mode from
Privileged EXEC
mode.
T2600G-28TS(config)#
Use the exit or the end
command or press Ctrl+Z to
return to Privileged EXEC mode.
Use the interface
gigabitEthernet port or
interface range
gigabitEthernet port-list
command to access interface
Configuration mode.
Use the vlan vlan-list to access
VLAN Configuration mode.
Interface Configuration Mode
Layer 2 Interface:
Use the interface
gigabitEthernet
port, interface
port-channel
port-channel-id or
interface range
gigabitEthernet
port-list command to
enter this mode from
Global Configuration
mode.
T2600G-28TS (config-if)#
or
T2600G-28TS(config-if-range)#
Use the end command or press Ctrl+Z to return to Privileged EXEC mode.
Enter the exit or the # command to return to Global Configuration mode.
A port number must be specified
in the interface command.
17
Mode Accessing Path Prompt Logout or Access the next
mode
Interface Configuration Mode
Layer 3 Interface:
Use the no switchport command to enter Routed Port mode from Interface Configuration mode.
Use the interface vlan vlan-id command to enter VLAN Interface mode from Global Configuration mode.
Use the interface
loopback id command to enter
Loopback Interface
mode from Global
Configuration mode.
T2600G-28TS (config-if)#
or
T2600G-28TS(config-if-range)#
Use the switchport command to switch to the Layer 2 interface mode.
Use the end command or press Ctrl+Z to return to Privileged EXEC mode.
Enter the exit or the # command
to return to Global Configuration
mode.
VLAN Configuration Mode
Use the vlan vlan-list command to enter
this mode from
Global Configuration
mode.
T2600G-28TS (config-vlan)#
Use the end command or press
Ctrl+Z to return to Privileged
EXEC mode.
Enter the exit command or the #
command to return to Global
configuration mode.
Note:
1. The user is automatically in User EXEC Mode after the connection between the PC and the switch is established by a Telnet/SSH connection.
2. Each command mode has its own set of specific commands. To configure some commands, you should access the corresponding command mode firstly.
Global Configuration Mode: In this mode, global commands are provided, such as the Spanning Tree, Schedule Mode and so on.
Interface Configuration Mode: In this mode, users can configure one or several ports, different ports corresponds to different commands
a). Interface gigabitEthernet: Configure parameters for an Ethernet port, such as Duplex-mode, flow control status.
b). Interface range gigabitEthernet: Configure parameters for several Ethernet ports.
18
c). Interface link-aggregation: Configure parameters for a link-aggregation, such as broadcast storm.
d). Interface range link-aggregation: Configure parameters for multi-trunks.
e). Interface vlan: Configure parameters for the vlan-port.
VLAN Configuration Mode: In this mode, users can create a VLAN and add a specified port to the VLAN.
3. Some commands are global, that means they can be performed in all modes:
show: Display all information of switch, for example: statistic information, port information, VLAN information.
history: Display the commands history.
1.3 Privilege Restrictions
This switch’s security is divided into four privilege levels: User level, Power User level, Operator level and Admin level. You can define username and password pairs, and assign a specific privilege level to each pair. Different privilege levels have access to specified commands, which is illustrated in the Privilege Requirement in each command. For details about how to configure usename and password pairs, please refer to user name (password) and user name (secret).
Users can enter Privileged EXEC mode from User EXEC mode by using the enable command. In default case, no password is needed. In Global Configuration Mode, you can configure password for Admin level by enable password command. Once password is configured, you are required to enter it to access Privileged EXEC mode.
1.4 Conventions
1.4.1 Format Conventions
The following conventions are used in this Guide:
Items in square brackets [ ] are optional
Items in braces { } are required
Alternative items are grouped in braces and separated by vertical bars. For example: speed {10 | 100 | 1000 }
Bold indicates an unalterable keyword. For example: show logging
19
Normal Font indicates a constant (several options are enumerated and only one can be selected). For example: mode {dynamic | static | permanent}
Italic Font indicates a variable (an actual value must be assigned). For example: bridge aging-time aging-time
1.4.2 Special Characters
You should pay attentions to the description below if the variable is a character string:
These six characters ” < > , \ & can not be input.
If a blank is contained in a character string, single or double quotation marks should be used, for example ’hello world’, ”hello world”, and the words in the quotation marks will be identified as a string. Otherwise, the words will be identified as several strings.
1.4.3 Parameter Format
Some parameters must be entered in special formats which are shown as follows:
MAC address must be enter in the format of xx:xx:xx:xx:xx:xx.
One or several values can be typed for a port-list or a vlan-list using comma to separate. Use a hyphen to designate a range of values, for instance,1/0/1,1/0/3-5,1/0/7 indicates choosing port 1/0/1,1/0/3,1/0/4,1/0/5,1/0/7.
20
Chapter 2 User Interface
2.1 enable Description
The enable command is used to access Privileged EXEC Mode from User EXEC Mode.
Syntax
enable
Command Mode
User EXEC Mode
Privilege Requirement
None.
Example
If you have set the password to access Privileged EXEC Mode from User EXEC Mode:
T2600G-28TS>enable
Enter password: T2600G-28TS#
2.2 service password-encryption Description
The service password-encryption command is used to encrypt the password when the password is defined or when the configuration is written, using the symmetric encryption algorithm. Encryption prevents the password from being readable in the configuration file. To disable the global encryption function, please use no service password-encryption command.
Syntax
service password-encryption no service password-encryption
21
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Enable the global encryption function:
T2600G-28TS(config)# service password-encryption
2.3 enable password Description
The enable password command is used to set or change the password for users to access Privileged EXEC Mode from User EXEC Mode. To remove the password, please use no enable password command. This command uses the symmetric encryption.
Syntax
enable password { [ 0 ] password | 7 encrypted-password } no enable password
Parameter
0 —— Specify the encryption type. 0 indicates that an unencrypted password will follow. By default, the encryption type is 0.
password —— Super password, a string from 1 to 31 alphanumeric characters or symbols. The password is case sensitive, allows digits, English letters (case sensitive), underlines and sixteen special characters ( !$%'()*,-./[]{|} ). By default, it is empty.
7 —— Indicates a symmetric encrypted password with fixed length will follow.
encrypted-password —— A symmetric encrypted password with fixed length, which you can copy from another switch’s configuration file. After the encrypted password is configured, you should use the corresponding unencrypted password if you re-enter this mode.
Command Mode
Global Configuration Mode
22
Privilege Requirement
Only Admin level users have access to these commands.
User Guidelines If the password you configured here is unencrypted and the global encryption function is enabled in service password-encryption, the password in the configuration file will be displayed in the symmetric encrypted form.
Example
Set the super password as “admin” and unencrypted to access Privileged EXEC Mode from User EXEC Mode:
T2600G-28TS(config)#enable password 0 admin
2.4 enable secret Description
The enable secret command is used to set a secret password, which is using an MD5 encryption algorithm, for users to access Privileged EXEC Mode from User EXEC Mode. To return to the default configuration, please use no enable secret command. This command uses the MD5 encryption.
Syntax
enable secret { [ 0 ] password | 5 encrypted-password } no enable secret
Parameter
0 —— Specify the encryption type. 0 indicates that an unencrypted password will follow. By default, the encryption type is 0.
password —— Super password, a string from 1 to 31 alphanumeric characters or symbols. The password is case sensitive, allows digits, English letters (case sensitive), underlines and sixteen special characters ( !$%'()*,-./[]{|} ). By default, it is empty. The password in the configuration file will be displayed in the MD5 encrypted form.
5 —— Indicates an MD5 encrypted password with fixed length will follow.
encrypted-password —— An MD5 encrypted password with fixed length, which you can copy from another switch’s configuration file. After the
23
encrypted password is configured, you should use the corresponding unencrypted password if you re-enter this mode.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
User Guidelines If both the enable password and enable secret are defined, you must enter the password set in enable secret.
Example
Set the secret password as “admin” and unencrypted to access Privileged EXEC Mode from User EXEC Mode. The password will be displayed in the encrypted form.
T2600G-28TS(config)#enable secret 0 admin
2.5 configure Description
The configure command is used to access Global Configuration Mode from Privileged EXEC Mode.
Syntax
configure
Command Mode
Privileged EXEC Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Access Global Configuration Mode from Privileged EXEC Mode: T2600G-28TS# configure T2600G-28TS(config)#
24
2.6 exit Description
The exit command is used to return to the previous Mode from the current Mode.
Syntax
exit
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Return to Global Configuration Mode from Interface Configuration Mode, and then return to Privileged EXEC Mode: T2600G-28TS(config-if)# exit T2600G-28TS(config)#exit T2600G-28TS#
2.7 end Description
The end command is used to return to Privileged EXEC Mode.
Syntax
end
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Return to Privileged EXEC Mode from Interface Configuration Mode: T2600G-28TS(config-if)#end T2600G-28TS#
25
2.8 clipaging Description
The clipaging command is used to enable the pause function for the screen display. If you want to display all the related information of the switch at once when using the show command, please use no clipaging command.
Syntax
clipaging no clipaging
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Disable the pause function for the screen display: T2600G-28TS(config)#no clipaging
2.9 history Description
The history command is used to show the latest 20 commands you entered in the current mode since the switch is powered.
Syntax
history
Command Mode
Privileged EXEC Mode and any Configuration Mode
Privilege Requirement
None.
Example
Show the commands you have entered in the current mode:
T2600G-28TS (config)# history
1 history
26
2.10 history clear Description
The history clear command is used to clear the commands you have entered in the current mode, therefore these commands will not be shown next time you use the history command.
Syntax
history clear
Command Mode
Privileged EXEC Mode and any Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Clear the commands you have entered in the current mode:
T2600G-28TS(config)#history clear
27
Chapter 3 IEEE 802.1Q VLAN Commands
VLAN (Virtual Local Area Network) technology is developed for the switch to divide the LAN into multiple logical LANs flexibly. Hosts in the same VLAN can communicate with each other, regardless of their physical locations. VLAN can enhance performance by conserving bandwidth, and improve security by limiting traffic to specific domains.
3.1 vlan Description
The vlan command is used to create IEEE 802.1Q VLAN and enter VLAN Configuration Mode. To delete the IEEE 802.1Q VLAN, please use no vlan command.
Syntax
vlan vlan-list no vlan vlan-list
Parameter
vlan-list —— Specify IEEE 802.1Q VLAN ID list, ranging from 2 to 4094, in the format of 2-3, 5. It is multi-optional.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create VLAN 2-10 and VLAN 100:
T2600G-28TS(config)# vlan 2-10,100
Delete VLAN 2:
T2600G-28TS(config)# no vlan 2
28
3.2 interface vlan Description
The interface vlan command is used to create VLAN Interface and enter Interface VLAN Mode. To delete VLAN Interface, please use no interface vlan command.
Syntax
interface vlan vlan-id no interface vlan vlan-id
Parameter
vlan-id —— Specify IEEE 802.1Q VLAN ID, ranging from 1 to 4094.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create VLAN Interface 2:
T2600G-28TS(config)# interface vlan 2
3.3 name Description
The name command is used to assign a description to a VLAN. To clear the description, please use no name command.
Syntax
name descript no name
Parameter
descript ——String to describe the VLAN, which contains 16 characters at most.
Command Mode
VLAN Configuration Mode(VLAN)
29
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the name of VLAN 2 as “group1”:
T2600G-28TS(config)# vlan 2
T2600G-28TS(config-vlan)# name group1
3.4 switchport mode
Description
The switchport mode command is used to configure the Link Types for the ports.
Syntax
switchport mode { access | trunk | general }
Parameter
access | trunk | general —— Link Types. There are three Link Types for the ports.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the Link Type of Gigabit Ethernet port 1/0/3 as “trunk”:
T2600G-28TS(config)#interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)#switchport mode trunk
30
3.5 switchport access vlan
Description
The switchport access vlan command is used to add the desired Access port to IEEE 802.1Q VLAN, or to remove a port from the corresponding VLAN.
Syntax
switchport access vlan vlan-id
no switchport access vlan
Parameter
vlan-id —— Specify IEEE 802.1Q VLAN ID, ranging from 2 to 4094.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure Gigabit Ethernet port 1/0/3 whose link type is “access” to VLAN 2:
T2600G-28TS(config)#interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)#switchport access vlan 2
3.6 switchport trunk allowed vlan
Description
The switchport trunk allowed vlan command is used to add the desired trunk port to IEEE 802.1Q VLAN. To remove a trunk port from the corresponding VLAN, please use no switchport trunk allowed vlan command.
Syntax
switchport trunk allowed vlan { vlan-list }
no switchport trunk allowed vlan { vlan-list }
31
Parameter
vlan-list —— VLAN ID list, ranging from 2 to 4094, in the format of 2-3, 5. It is multi-optional.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the link type of port 2 as trunk and add it to VLAN 2:
T2600G-28TS(config)#interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)#switchport mode trunk
T2600G-28TS(config-if)#switchport trunk allowed vlan 2
3.7 switchport trunk allowed vlan all
Description
The switchport trunk allowed vlan all command is used to add the desired trunk port to all the IEEE 802.1Q VLANs. To remove a trunk port from all the IEEE 802.1Q VLANs, please use no switchport trunk allowed vlan all command.
Syntax
switchport trunk allowed vlan all
no switchport trunk allowed vlan all
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
32
Example
Configure the link type of port 2 as trunk and add it to all the VLANs:
T2600G-28TS(config)#interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)#switchport mode trunk
T2600G-28TS(config-if)# switchport trunk allowed vlan all
3.8 switchport general allowed vlan
Description
The switchport general allowed vlan command is used to add the desired General port to IEEE 802.1Q VLAN, or to remove a port from the corresponding VLAN.
Syntax
switchport general allowed vlan vlan-list { tagged | untagged }
no switchport general allowed vlan vlan-list
Parameter
vlan-list —— VLAN ID list, ranging from 2 to 4094, in the format of 2-3, 5. It is multi-optional.
tagged | untagged —— egress-rule.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure Gigabit Ethernet port 1/0/4 whose link type is “general” to VLAN 2 and its egress-rule as “tagged”:
T2600G-28TS(config)#interface gigabitEthernet 1/0/4
T2600G-28TS(config-if)#switchport mode general
T2600G-28TS(config-if)#switchport general allowed vlan 2 tagged
33
3.9 switchport pvid Description
The switchport pvid command is used to configure the PVID for the switch ports.
Syntax
switchport pvid vlan-id
Parameter
vlan-id —— VLAN ID, ranging from 1 to 4094.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the PVID of port 1/0/2 as 2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# switchport pvid 2
3.10 show vlan summary Description
The show vlan summary command is used to display the summarized information of IEEE 802.1Q VLAN.
Syntax
show vlan summary
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
34
Example
Display the summarized information of IEEE 802.1Q VLAN:
T2600G-28TS(config)# show vlan summary
3.11 show vlan brief Description
The show vlan brief command is used to display the brief information of IEEE 802.1Q VLAN.
Syntax
show vlan brief
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the brief information of IEEE 802.1Q VLAN:
T2600G-28TS(config)# show vlan brief
3.12 show vlan Description
The show vlan command is used to display the information of IEEE 802.1Q VLAN.
Syntax
show vlan [ id vlan-id ]
Parameter
vlan-id —— Specify IEEE 802.1Q VLAN ID, ranging from 1 to 4094. It is multi-optional. Using the show vlan command without parameter displays the detailed information of all VLANs.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
35
Privilege Requirement
None.
Example
Display the information of vlan 5:
T2600G-28TS(config)# show vlan id 5
3.13 show interface switchport Description
The show interface switchport command is used to display the IEEE 802.1Q VLAN configuration information of the specified port/port channel.
Syntax
show interface switchport [ gigabitEthernet port | port-channel port-channel-id ]
Parameter
port —— The port number. port-channel-id —— The ID of the port channel.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the VLAN configuration information of all ports and port channels:
T2600G-28TS(config)# show interface switchport
36
Chapter 4 MAC-based VLAN Commands
MAC VLAN (Virtual Local Area Network) is the way to classify the VLANs based on MAC Address. A MAC address is relative to a single VLAN ID. The untagged packets and the priority-tagged packets coming from the MAC address will be tagged with this VLAN ID.
4.1 mac-vlan mac-address
Description
The mac-vlan mac-address command is used to create a MAC-based VLAN entry. To delete a MAC-based VLAN entry, please use the no mac-vlan mac-address command.
Syntax
mac-vlan mac-address mac-addr vlan vlan-id [description descript]
no mac-vlan mac-address mac-addr
Parameter
mac-addr —— MAC address, in the format of XX:XX:XX:XX:XX:XX.
vlan-id —— Specify IEEE 802.1Q VLAN ID, ranging from 1 to 4094.
descript —— Give a description to the MAC address for identification, which contains 8 characters at most.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create VLAN 2 with the MAC address 00:11:11:01:01:12 and the name “TP”:
T2600G-28TS(config)#mac-vlan mac-address 00:11:11:01:01:12 vlan 2
description TP
37
4.2 mac-vlan
Description
The mac-vlan command is used to enable a port for the MAC-based VLAN feature. Only the port is enabled can the configured MAC-based VLAN take effect. To disable the MAC-based VLAN function, please use no mac-vlan command. All the ports are disabled by default.
Syntax
mac-vlan
no mac-vlan
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the Gigabit Ethernet port 1/0/3 for the MAC-based VLAN feature:
T2600G-28TS(config)#interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)#mac-vlan
4.3 show mac-vlan
Description
The show mac-vlan command is used to display the information of the MAC-based VLAN entry. MAC address and VLAN ID can be used to filter the displayed information.
Syntax
show mac-vlan { all | mac-address mac-addr | vlan vlan-id }
Command Mode
Privileged EXEC Mode and Any Configuration Mode
38
Privilege Requirement
None.
Parameter
mac-addr —— MAC address, in the format of XX:XX:XX:XX:XX:XX.
vlan-id —— Specify IEEE 802.1Q VLAN ID, ranging from 1 to 4094.
Example
Display the information of all the MAC-based VLAN entry:
T2600G-28TS(config)#show mac-vlan all
4.4 show mac-vlan interface
Description
The show mac-vlan interface command is used to display the port state of MAC-based VLAN.
Syntax
show mac-vlan interface
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the enable state of all the ports:
T2600G-28TS(config)#show mac-vlan interface
39
Chapter 5 Protocol-based VLAN Commands
Protocol VLAN (Virtual Local Area Network) is the way to classify VLANs based on Protocols. A Protocol is relative to a single VLAN ID. The untagged packets and the priority-tagged packets matching the protocol template will be tagged with this VLAN ID.
5.1 protocol-vlan template (For T2600G-18TS
only)
Description
The protocol-vlan template command is used to create Protocol-based VLAN template. To delete Protocol-based VLAN template, please use no protocol-vlan template command.
Syntax
protocol-vlan template name protocol-name frame { ether_2 ether-type type }
no protocol-vlan template template-idx
Parameter
protocol-name —— Give a name for the Protocol-based VLAN Template , which contains 8 characters at most.
ether_2 ether-type type —— Specify the Ethernet type.
template-idx —— The number of the Protocol-based VLAN Template. You can get the template corresponding to the number by the show protocol-vlan template command.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create a Protocol-based VLAN template named “TP” whose Ethernet protocol type is 0x2024:
40
T2600G-18TS(config)#protocol-vlan template name TP frame ether_2
ether-type 2024
5.2 protocol-vlan template (For other switches)
Description
The protocol-vlan template command is used to create Protocol-based VLAN template. To delete Protocol-based VLAN template, please use no protocol-vlan template command.
Syntax
protocol-vlan template name protocol-name frame { ether_2 ether-type type | snap ether-type type | llc dsap dsap_type ssap ssap_type }
no protocol-vlan template template-idx
Parameter
protocol-name —— Give a name for the Protocol-based VLAN Template , which contains 8 characters at most.
ether_2 ether-type type —— Specify the Ethernet type.
snap ether-type type —— Specify the Ethernet type.
llc dsap dsap_type ssap ssap_type —— Specify the DSAP type and the SSAP type.
template-idx —— The number of the Protocol-based VLAN Template. You can get the template corresponding to the number by the show protocol-vlan template command.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create a Protocol-based VLAN template named “TP” whose Ethernet protocol type is 0x2024:
41
T2600G-28TS(config)#protocol-vlan template name TP frame ether_2
ether-type 2024
5.3 protocol-vlan vlan
Description
The protocol-vlan vlan command is used to create a Protocol-based VLAN entry. To delete a Protocol-based VLAN entry, please use no protocol-vlan vlan command.
Syntax
protocol-vlan vlan vlan-id template template-idx
no protocol-vlan vlan group-idx
Parameter
vlan-id —— Specify IEEE 802.1Q VLAN ID, ranging from 1-4094.
template-idx ——The number of the Protocol-based VLAN Template. You can get the template corresponding to the number by the show protocol-vlan template command.
group-idx ——The number of the Protocol-based VLAN entry. You can get the Protocol-based VLAN entry corresponding to the number by the show protocol-vlan vlan command.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create Protocol-based VLAN 2 and bind it with Protocol-based VLAN Template 3:
T2600G-28TS(config)#protocol-vlan vlan 2 template 3
42
5.4 protocol-vlan group
Description
The protocol-vlan command is used to add the port to a specified protocol group. To remove the port from this protocol group, please use no protocol-vlan group command.
Syntax
protocol-vlan group index
no protocol-vlan group index
Parameter
index —— Specify the protocol group ID.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Add Gigabit Ethernet port 20 to protocol group 1:
T2600G-28TS(config)#interface gigabitEthernet 1/0/20
T2600G-28TS(config-if)#protocol-vlan group 1
5.5 show protocol-vlan template
Description
The show protocol-vlan template command is used to display the information of the Protocol-based VLAN templates.
Syntax
show protocol-vlan template
Command Mode
Privileged EXEC Mode and Any Configuration Mode
43
Privilege Requirement
None.
Example
Display the information of the Protocol-based VLAN templates:
T2600G-28TS(config)#show protocol-vlan template
5.6 show protocol-vlan vlan
Description
The show protocol-vlan vlan command is used to display the information about Protocol-based VLAN entry.
Syntax
show protocol-vlan vlan
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display information of the Protocol-based VLAN entry:
T2600G-28TS(config)#show protocol-vlan vlan
44
Chapter 6 VLAN-VPN Commands
VLAN-VPN (Virtual Private Network) function, the implement of a simple and flexible Layer 2 VPN technology, allows the packets with VLAN tags of private networks to be encapsulated with VLAN tags of public networks at the network access terminal of the Internet Service Provider. And these packets will be transmitted with double-tag across the public networks.
6.1 dot1q-tunnel
Description
The dot1q-tunnel command is used to enable the VLAN-VPN function globally. To disable the VLAN-VPN function, please use the no dot1q-tunnel command.
Syntax
dot1q-tunnel no dot1q-tunnel
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the VLAN-VPN function globally:
T2600G-28TS(config)#dot1q-tunnel
6.2 dot1q-tunnel tpid
Description
The dot1q-tunnel tpid command is used to configure Global TPID of the VLAN-VPN. To restore to the default value, please use the no dot1q-tunnel tpid command.
45
Syntax
dot1q-tunnel tpid tpid no dot1q-tunnel tpid
Parameter
tpid —— The value of Global TPID. It must be 4 Hex integers. By default, it is 8100.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure Global TPID of the VLAN-VPN as 0x9100:
T2600G-28TS(config)#dot1q-tunnel tpid 9100
6.3 dot1q-tunnel mapping
Note: T2600G-18TS doesn’t support this command.
Description
The dot1q-tunnel mapping command is used to enable the VLAN Mapping feature globally. To disable this function, please use the no dot1q-tunnel mapping command. By default, the VLAN Mapping feature is disabled.
Syntax
dot1q-tunnel mapping no dot1q-tunnel mapping
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
46
Example
Enable the VLAN mapping feature globally:
T2600G-28TS(config)#dot1q-tunnel mapping
6.4 switchport dot1q-tunnel missdrop
Description
The switchport dot1q-tunnel missdrop command is used to enable the VLAN-VPN missdrop function for a specific port. To disable the VLAN-VPN missdrop function, please use the no switchport dot1q-tunnel missdrop command.
Syntax
switchport dot1q-tunnel missdrop no switchport dot1q-tunnel missdrop
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the VLAN-VPN missdrop function for Gigabit Ethernet port 1/0/3:
T2600G-28TS(config)#interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)#switchport dot1q-tunnel missdrop
6.5 switchport dot1q-tunnel mapping
Description
The switchport dot1q-tunnel mapping command is used add the VLAN Mapping entry on a specified port. To delete the VLAN Mapping entry on this port, please use the no switchport dot1q-tunnel mapping command.
47
Syntax
switchport dot1q-tunnel mapping c-vlan sp-vlan [descript] no switchport dot1q-tunnel mapping c-vlan
Parameter
c-vlan —— Customer VLAN ID, ranging from 1 to 4094. sp-vlan —— Service Provider VLAN ID, ranging from 1 to 4094. descript —— Give a description to the VLAN Mapping entry, which contains 15 characters at most.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Add a VLAN Mapping entry on the Gigabit Ethernet port 1/0/3 with the Customer VLAN as VLAN 2 and the Service Provider VLAN as VLAN 3:
T2600G-28TS(config)#interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)#switchport dot1q-tunnel mapping 2 3
6.6 switchport dot1q-tunnel mode
Description
The switchport dot1q-tunnel mode command is used to configure the VPN port’s mode. To close this VPN port, please use the no switchport dot1q-tunnel mode command. By default, no port has been configured as the VPN port. The VPN port mode uni and nni cannot switch to each other directly, so please close the VPN port and switch to the other mode if needed.
Syntax
switchport dot1q-tunnel mode { uni/nni } no switchport dot1q-tunnel mode
48
Parameter
uni ——The port connected to the clients. (Note: T2600G-18TS does’t support uni port setting.) nni ——The port connected to the ISP.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the Gigabit Ethernet port 1/0/3 as the VPN UNI ports:
T2600G-28TS(config)#interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)#switchport dot1q-tunnel mode uni
6.7 show dot1q-tunnel
Description
The show dot1q-tunnel command is used to display the global configuration information of the VLAN VPN.
Syntax
show dot1q-tunnel
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the global configuration information of the VLAN VPN:
T2600G-28TS(config)#show dot1q-tunnel
49
6.8 show dot1q-tunnel mapping
Description
The show dot1q-tunnel mapping command is used to display the information of VLAN Mapping entry.
Syntax
show dot1q-tunnel mapping
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the information of VLAN Mapping entry:
T2600G-28TS(config)#show dot1q-tunnel mapping
6.9 show dot1q-tunnel interface
Description
The show dot1q-tunnel mapping interface command is used to display the VLAN VPN port type.
Syntax
show dot1q-tunnel interface
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the port type of all VLAN VPN ports:
T2600G-28TS(config)#show dot1q-tunnel interface
50
Chapter 7 Private VLAN Commands
Note: T2600G-18TS doesn't support Private VLAN feature.
Private VLANs are configured specially for saving VLAN resource of uplink devices and decreasing broadcast.
7.1 private-vlan primary
Description
The private-vlan primary command is used to configure the designated VLAN as the primary VLAN of the Private VLAN. To remove the primary VLAN property pf the current VLAN, please use no private-vlan primary command.
Syntax
private-vlan primary
no private-vlan primary
Command Mode
VLAN Configuration Mode (VLAN)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure the VLAN 3 as the primary VLAN of the private VLAN:
T2600G-28TS(config)#vlan 3
T2600G-28TS(config-vlan)#private-vlan primary
7.2 private-vlan community
Description
The private-vlan community command is used to configure the designated VLAN as the community VLAN of the Private VLAN. To remove the community VLAN property pf the current VLAN, please use no private-vlan community command.
51
Syntax
private-vlan community
no private-vlan community
Command Mode
VLAN Configuration Mode (VLAN)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure the VLAN 4 as the community VLAN of the private VLAN:
T2600G-28TS(config)#vlan 4
T2600G-28TS(config-vlan)#private-vlan community
7.3 private-vlan isolated
Description
The private-vlan isolated command is used to configure the designated VLAN as the isolated VLAN of the Private VLAN. To remove the isolated VLAN property pf the current VLAN, please use no private-vlan isolated command.
Syntax
private-vlan isolated
no private-vlan isolated
Command Mode
VLAN Configuration Mode (VLAN)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure the VLAN 3 as the isolated VLAN of the private VLAN:
T2600G-28TS(config)#vlan 3
T2600G-28TS(config-vlan)#private-vlan isolated
52
7.4 private-vlan association
Description
The private-vlan association command is used to associate primary VLAN with secondary VLAN. To exterminate the currently association, please use no private-vlan association command.
Syntax
private-vlan association vlan_list
no private-vlan association vlan_list
Parameter
vlan_list —— Secondary VLAN ID, ranging from 2 to 4094.
Command Mode
VLAN Configuration Mode (VLAN)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Associate primary VLAN 3 with community VLAN 4 as a private VLAN:
T2600G-28TS(config)#vlan 3
T2600G-28TS(config-vlan)#private-vlan association 4
7.5 switchport private-vlan
Description
The switchport private-vlan command is used to configure the private VLAN mode for the switchport. To invalid the configuration, please use no switchport private-vlan command.
Syntax
switchport private-vlan { promiscuous | host }
no switchport private-vlan
Parameter
promiscuous | host —— Configure the private VLAN mode for the switchport.
53
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure Gigabit Ethernet port 3 as “host”:
T2600G-28TS(config)#interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)#switchport private-vlan host
7.6 switchport private-vlan host-association
Description
The switchport private-vlan host-association command is used to add host type port to private VLAN. To remove the port from Private VLAN, please use no switchport private-vlan host-association command.
Syntax
switchport private-vlan host-association primary_vlan_id secondary_vlan_id vlantype
no switchport private-vlan host-association
Parameter
primary-vlan-id —— Primary VLAN ID, ranging from 2 to 4094.
secondary-vlan-id —— Secondary VLAN ID, ranging from 2 to 4094.
vlantype —— Specify the type of the secondary VLAN, either community or isolated.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
54
Example
Configure host type Gigabit Ethernet port 1/0/3 as a member of primary VLAN 3 and secondary VLAN 4, with the type of VLAN 4 as community:
T2600G-28TS(config)#interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)#switchport private-vlan host-association 3 4
community
7.7 switchport private-vlan mapping
Description
The switchport private-vlan mapping command is used to add promiscuous type port to private VLAN. To remove the port from Private VLAN, please use no switchport private-vlan mapping command.
Syntax
switchport private-vlan mapping primary_vlan_id secondary_vlan_id
no switchport private-vlan mapping
Parameter
primary-vlan-id —— Primary VLAN ID, ranging from 2 to 4094.
secondary-vlan-id —— Secondary VLAN ID, ranging from 2 to 4094.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure promiscuous type Gigabit Ethernet port 1/0/3 as a member of primary VLAN 3 and secondary VLAN 4:
T2600G-28TS(config)#interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)#switchport private-vlan mapping 3 4
55
7.8 show vlan private-vlan
Description
The show vlan private-vlan command is used to display the Private VLAN configuration information of the switch.
Syntax
show vlan private-vlan
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Display the configuration information of all Private VLAN:
T2600G-28TS(config)#show vlan private-vlan
7.9 show vlan private-vlan interface
Description
The show vlan private-vlan interface command is used to display the Private VLAN configuration information of the specified port(s).
Syntax
show vlan private-vlan interface [gigabitEthernet port | port-channel port-channel-id ]
Parameter
port —— The port number. port-channel-id —— The ID of the port channel.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
56
Example
Display the configuration information of all the Ethernet ports:
T2600G-28TS(config)#show vlan private-vlan interface
57
Chapter 8 L2PT Commands
L2PT (Layer 2 Protocol Tunneling) is a feature for service providers to transmit packets from different customers across their ISP networks and maintain Layer 2 protocol configurations of each customer. The supported Layer 2 protocols are STP (Spanning Tree Protocol), GVRP (GARP VLAN Registration Protocol), CDP (Cisco Discovery Protocol), VTP (VLAN Trunking Protocol), PAgP (Port Aggregation Protocol), UDLD (UniDirectional Link Detection) and PVST+(Per VLAN Spanning Tree Plus).
8.1 l2protocol-tunnel Description
The l2protocol-tunnel command is used to enable the layer 2 protocol tunneling (L2PT) function globally. To disable the L2PT function, please use no l2protocol-tunnel command.
Syntax
l2protocol-tunnel
no l2protocol-tunnel
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Enable the L2PT function globally:
T2600G-28TS(config)# l2protocol-tunnel
8.2 l2protocol-tunnel type
Description
The l2protocol-tunnel type command is used to configure the L2PT function on a specified port. To disable the L2PT function on the specified port, please use no l2protocol-tunnel command.
58
Syntax
l2protocol-tunnel type nni
l2protocol-tunnel type uni { 01000ccccccc | 01000ccccccd | gvrp | stp | lacp | all } [ threshold threshold ]
no l2protocol-tunnel
Parameter
nni —— Specify the port type according to its connecting device in the network. Specify the port’s type as NNI if it is connecting to the ISP network.
uni —— Specify the port type according to its connecting device in the network. Specify the port’s type as UNI if it is connecting to the user’s local network.
01000ccccccc | 01000ccccccd | gvrp | stp | lacp | all —— Select the supported Layer 2 protocol type. Packets of the specified protocol will be encapsulated with their destination MAC address before they are sent to the ISP network. Packets will be decapsulated to restore their Layer 2 protocol and MAC address information before they are sent to the customer network.
• 01000ccccccc: Enable protocol tunneling for the packets with destination MAC address 01-00-0C-CC-CC-CC. 01-00-0CC-CC-CC-CC is used as the destination MAC address of the CDP/VTP/PAgP/UDLD packets.
• 01000ccccccd: Enable protocol tunneling for the packets with destination MAC address 01-00-0C-CC-CC-CD. 01-00-0CC-CC-CC-CD is used as the destination MAC address of Cisco PVST+ BPDUs.
• gvrp: Enable protocol tunneling for the GVRP packets.
• stp: Enable protocol tunneling for the STP packets.
lacp: Enable protocol tunneling for the LACP packets.
• all: All the above Layer 2 protocols are supported for tunneling.
threshold ——Configure the threshold for packets-per-second accepted for encapsulation. Packets beyond the threshold will be dropped. It ranges from 0 to 1000.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
59
Example
Configure port 1/0/3 as a UNI port for STP packets with the threshold as 1000 packets/second:
T2600G-28TS(config)#interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# l2protocol-tunnel type uni stp threshold 1000
8.3 show l2protocol-tunnel global Description
The show l2protocol-tunnel global command is used to display the global L2PT status.
Syntax
show l2protocol-tunnel global
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the global L2PT status:
T2600G-28TS(config)# show l2protocol-tunnel global
8.4 show l2protocol-tunnel interface Description
The show l2protocol-tunnel interface command is used to display the L2PT configuration information of a specified Ethernet port or of all Ethernet ports.
Syntax
show l2protocol-tunnel interface [ gigabitEthernet port | port-channel port-channel-id ]
Parameter
port —— The port number. port-channel-id —— The ID of the port channel.
60
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the L2PT configuration information of Gigabit Ethernet port 1/0/1:
T2600G-28TS(config)#show l2protocol-tunnel interface gigabitEthernet
1/0/1
Display the L2PT configuration information of all Ethernet ports:
T2600G-28TS(config)#show l2protocol-tunnel interface
61
Chapter 9 GVRP Commands
GVRP (GARP VLAN registration protocol) is an implementation of GARP (generic attribute registration protocol). GVRP allows the switch to automatically add or remove the VLANs via the dynamic VLAN registration information and propagate the local VLAN registration information to other switches, without having to individually configure each VLAN.
9.1 gvrp Description
The gvrp command is used to enable the GVRP function globally. To disable the GVRP function, please use no gvrp command.
Syntax
gvrp
no gvrp
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the GVRP function globally:
T2600G-28TS(config)#gvrp
9.2 gvrp (interface) Description
The gvrp command is used to enable the GVRP function for the desired port. To disable it, please use no gvrp command. The GVRP feature can only be enabled for the trunk-type ports.
Syntax
gvrp
62
no gvrp
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the GVRP function for Gigabit Ethernet ports 1/0/2-6:
T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-6
T2600G-28TS(config-if-range)#gvrp
9.3 gvrp registration Description
The gvrp registration command is used to configure the GVRP registration type for the desired port. To restore to the default value, please use no gvrp registration command.
Syntax
gvrp registration { normal | fixed | forbidden }
no gvrp registration
Parameter
normal | fixed | forbidden —— Registration mode. By default, the registration mode is “normal”.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
63
Example
Configure the GVRP registration mode as “fixed” for Gigabit Ethernet ports 1/0/2-6:
T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-6
T2600G-28TS(config-if-range)#gvrp registration fixed
9.4 gvrp timer Description
The gvrp timer command is used to set a GVRP timer for the desired port. To restore to the default setting of a GARP timer, please use no gvrp timer command.
Syntax
gvrp timer { leaveall | join | leave } value
no gvrp timer [leaveall | join | leave]
Parameter
leaveall | join | leave —— They are the three timers: leave All, join and leave. Once the LeaveAll Timer is set, the port with GVRP enabled can send a LeaveAll message after the timer times out, so that other GARP ports can re-register all the attribute information. After that, the LeaveAll timer will start to begin a new cycle. To guarantee the transmission of the Join messages, a GARP port sends each Join message two times. The Join Timer is used to define the interval between the two sending operations of each Join message. Once the Leave Timer is set, the GARP port receiving a Leave message will start its Leave timer, and deregister the attribute information if it does not receive a Join message again before the timer times out.
value ——The value of the timer. The LeaveAll Timer ranges from 1000 to 30000 centiseconds and the default value is 1000 centiseconds. The Join Timer ranges from 20 to 1000 centiseconds and the default value is 20 centiseconds. The Leave Timer ranges from 60 to 3000 centiseconds and the default value is 60 centiseconds.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
64
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Set the GARP leaveall timer of Gigabit Ethernet port 1/0/6 as 2000 centiseconds and restore the join timer of it to the default value:
T2600G-28TS(config)#interface gigabitEthernet 1/0/6
T2600G-28TS(config-if)#gvrp timer leaveall 2000
T2600G-28TS(config-if)#no gvrp timer join
9.5 show gvrp interface Description
The show gvrp interface command is used to display the GVRP configuration information of a specified Ethernet port or of all Ethernet ports.
Syntax
show gvrp interface [ gigabitEthernet port | port-channel port-channel-id ]
Parameter
port —— The port number. port-channel-id —— The ID of the port channel.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the GVRP configuration information of Gigabit Ethernet port 1:
T2600G-28TS(config)#show gvrp interface gigabitEthernet 1/0/1
Display the GVRP configuration information of all Ethernet ports:
T2600G-28TS(config)#show gvrp interface
65
9.6 show gvrp global Description
The show gvrp global command is used to display the global GVRP status.
Syntax
show gvrp global
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the global GVRP status:
T2600G-28TS(config)#show gvrp global
66
Chapter 10 Voice VLAN Commands
Voice VLANs are configured specially for voice data stream. By configuring Voice VLANs and adding the ports with voice devices attached to voice VLANs, you can perform QoS-related configuration for voice data, ensuring the transmission priority of voice data stream and voice quality.
10.1 voice vlan Description
The voice vlan command is used to enable Voice VLAN function. To disable Voice VLAN function, please use no voice vlan command.
Syntax
voice vlan vlan-id
no voice vlan
Parameter
vlan-id —— Specify IEEE 802.1Q VLAN ID, ranging from 2 to 4094.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the Voice VLAN function for VLAN 10:
T2600G-28TS(config)# voice vlan 10
10.2 voice vlan aging Description
The voice vlan aging command is used to set the aging time for a voice VLAN. To restore to the default aging time for the Voice VLAN, please use no voice vlan aging command.
67
Syntax
voice vlan aging time
no voice vlan aging
Parameter
time —— Aging time (in minutes) to be set for the Voice VLAN. It ranges from 1 to 43200 minutes and the default value is 1440 minutes.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Set the aging time for the Voice VLAN as 1 minute:
T2600G-28TS(config)# voice vlan aging 1
10.3 voice vlan priority Description
The voice vlan priority command is used to configure the priority for the Voice VLAN. To restore to the default priority, please use no voice vlan priority command.
Syntax
voice vlan priority pri
no voice vlan priority
Parameter
pri —— Priority, ranging from 0 to 7, and the default value is 6.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
68
Example
Configure the priority of the Voice VLAN as 5:
T2600G-28TS(config)# voice vlan priority 5
10.4 voice vlan mac-address Description
The voice vlan mac-address command is used to create Voice VLAN OUI. To delete the specified Voice VLAN OUI, please use no voice vlan mac-address command.
Syntax
voice vlan mac-address mac-addr mask mask [ description descript ]
no voice vlan mac-address mac-addr
Parameter
mac-addr —— The OUI address of the voice device, in the format of XX:XX:XX:XX:XX:XX.
mask —— The OUI address mask of the voice device, in the format of XX:XX:XX:XX:XX:XX.
descript ——Give a description to the OUI for identification which contains 16 characters at most.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create a Voice VLAN OUI described as TP-Phone with the OUI address 00:11:11:11:11:11 and the mask address FF:FF:FF:00:00:00:
T2600G-28TS(config)#voice vlan mac-address 00:11:11:11:11:11 mask
FF:FF:FF:00:00:00 description TP-Phone
69
10.5 switchport voice vlan mode Description
The switchport voice vlan mode command is used to configure the Voice VLAN mode for the Ethernet port.
Syntax
switchport voice vlan mode { manual | auto }
Parameter
manual | auto —— Port mode.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the port 1/0/3 to operate in the auto voice VLAN mode:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# switchport voice vlan mode auto
10.6 switchport voice vlan security Description
The switchport voice vlan security command is used to enable the Voice VLAN security feature. To disable the Voice VLAN security feature, please use no switchport voice vlan security command.
Syntax
switchport voice vlan security
no switchport voice vlan security
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
70
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable port 1/0/3 for the Voice VLAN security feature:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# switchport voice vlan security
10.7 show voice vlan Description
The show voice vlan command is used to display the global configuration information of Voice VLAN.
Syntax
show voice vlan
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Display the configuration information of Voice VLAN globally:
T2600G-28TS(config)# show voice vlan
10.8 show voice vlan oui Description
The show voice vlan oui command is used to display the configuration information of Voice VLAN OUI.
Syntax
show voice vlan oui
71
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Display the configuration information of Voice VLAN OUI:
T2600G-28TS(config)# show voice vlan oui
10.9 show voice vlan switchport Description
The show voice vlan switchport command is used to display the Voice VLAN configuration information of a specified port/port channel.
Syntax
show voice vlan switchport [ gigabitEthernet port | port-channel port-channel-id ]
Parameter
port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Display the Voice VLAN configuration information of all ports and port channels:
T2600G-28TS(config)# show voice vlan switchport
Display the Voice VLAN configuration information of port 1/0/2:
T2600G-28TS(config)# show voice vlan switchport gigabitEthernet 1/0/2
72
Chapter 11 Etherchannel Commands
Etherchannel Commands are used to configure LAG and LACP function.
LAG (Link Aggregation Group) is to combine a number of ports together to make a single high-bandwidth data path, which can highly extend the bandwidth. The bandwidth of the LAG is the sum of bandwidth of its member port.
LACP (Link Aggregation Control Protocol) is defined in IEEE802.3ad and enables the dynamic link aggregation and disaggregation by exchanging LACP packets with its partner. The switch can dynamically group similarly configured ports into a single logical link, which will highly extend the bandwidth and flexibly balance the load.
11.1 channel-group Description
The channel-group command is used to add a port to the EtherChannel Group and configure its mode. To delete the port from the EtherChannel Group, please use no channel-group command.
Syntax
channel-group num mode { on | active | passive }
no channel-group
Parameter
num —— The number of the EtherChannel Group, ranging from 1 to 14.
on —— Enable the static LAG.
active —— Enable the active LACP mode.
passive —— Enable the passive LACP mode.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
73
Example
Add ports 2-4 to EtherChannel Group 1 and enable the static LAG:
T2600G-28TS(config)# interface range gigabitEthernet 1/0/2-4
T2600G-28TS(config-if-range)# channel-group 1 mode on
11.2 port-channel load-balance Description
The port-channel load-balance command is used to configure the Aggregate Arithmetic for LAG. To return to the default configurations, please use no port-channel load-balance command.
Syntax
port-channel load-balance { src-mac | dst-mac | src-dst-mac | src-ip | dst-ip | src-dst-ip }
no port-channel load-balance
Parameter
src-mac —— The source MAC address. When this option is selected, the Aggregate Arithmetic will be based on the source MAC address of the packets.
dst-mac —— The destination MAC address. When this option is selected, the Aggregate Arithmetic will be based on the destination MAC address of the packets.
src-dst-mac —— The source and destination MAC address. When this option is selected, the Aggregate Arithmetic will be based on the source and destination MAC addresses of the packets. The Aggregate Arithmetic for LAG is “src-dst-mac” by default.
src-ip —— The source IP address. When this option is selected, the Aggregate Arithmetic will be based on the source IP address of the packets.
dst-ip —— The destination IP address. When this option is selected, the Aggregate Arithmetic will be based on the destination IP address of the packets.
src-dst-ip —— The source and destination IP address. When this option is selected, the Aggregate Arithmetic will be based on the source and destination IP addresses of the packets.
74
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the Aggregate Arithmetic for LAG as “src-dst-ip”:
T2600G-28TS(config)# port-channel load-balance src-dst-ip
11.3 lacp system-priority Description
The lacp system-priority command is used to configure the LACP system priority globally. To return to the default configurations, please use no lacp system-priority command.
Syntax
lacp system-priority pri
no lacp system-priority
Parameter
pri —— The system priority, ranging from 0 to 65535. It is 32768 by default.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the LACP system priority as 1024 globally:
T2600G-28TS(config)# lacp system-priority 1024
75
11.4 lacp port-priority Description
The lacp port-priority command is used to configure the LACP port priority for specified ports. To return to the default configurations, please use no lacp port-priority command.
Syntax
lacp port-priority pri
no lacp port-priority
Parameter
pri —— The port priority, ranging from 0 to 65535. It is 32768 by default.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the LACP port priority as 1024 for ports 1-3:
T2600G-28TS(config)# interface range gigabitEthernet 1/0/1-3
T2600G-28TS(config-if-range)# lacp port-priority 1024
Configure the LACP port priority as 2048 for port 4:
T2600G-28TS(config)# interface gigabitEthernet 1/0/4
T2600G-28TS(config-if)# lacp port-priority 2048
11.5 show etherchannel Description
The show etherchannel command is used to display the EtherChannel information.
Syntax show etherchannel [ channel-group-num ] { detail | summary }
76
Parameter
channel-group-num —— The EtherChannel Group number, ranging from 1 to 14. By default, it is empty, and will display the information of all EtherChannel Groups.
detail —— The detailed information of EtherChannel.
summary —— The EtherChannel information in summary.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the detailed information of EtherChannel Group 1:
T2600G-28TS(config)# show etherchannel 1 detail
11.6 show etherchannel load-balance Description
The show etherchannel load-balance command is used to display the Aggregate Arithmetic of LAG.
Syntax
show etherchannel load-balance
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the Aggregate Arithmetic of LAG:
T2600G-28TS(config)# show etherchannel load-balance
77
11.7 show lacp Description
The show lacp command is used to display the LACP information for a specified EtherChannel Group.
Syntax
show lacp [ channel-group-num ] { internal | neighbor }
Parameter channel-group-num —— The EtherChannel Group number, ranging from 1 to 14. By default, it is empty, and will display the information of all LACP groups.
internal —— The internal LACP information.
neighbor —— The neighbor LACP information.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the internal LACP information of EtherChannel Group 1:
T2600G-28TS(config)# show lacp 1 internal
11.8 show lacp sys-id Description
The show lacp sys-id command is used to display the LACP system priority globally.
Syntax
show lacp sys-id
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
78
Example
Display the LACP system priority:
T2600G-28TS(config)# show lacp sys-id
79
Chapter 12 User Management Commands
User Manage Commands are used to manage the user’s logging information by Web, Telnet or SSH, so as to protect the settings of the switch from being randomly changed.
12.1 user name (password) Description
The user name command is used to add a new user or modify the existed users’ information. To delete the existed users, please use no user name command. This command uses the symmetric encryption.
Syntax
user name name [ privilege admin | operator | power_user | user ] password { [ 0 ] password | 7 encrypted-password }
no user name name
Parameter
name ——Type a name for users' login, which contains 16 characters at most, composed of digits, English letters and under dashes only.
admin | operator | power_user | user —— Access level. “admin” means that you can edit, modify and view all the settings of different functions. “operator” means that you can edit, modify and view most of the settings of different functions. “power-user” means that you can edit, modify and view some of the settings of different functions. “user” means that you can only view some of the settings of different functions without the right to edit or modify. It is “admin” by default. For more details about privilege restrictions, please refer to the Privilege Requirement part in each command.
0 —— Specify the encryption type. 0 indicates that an unencrypted password will follow. By default, the encryption type is 0.
password —— Users’ login password, a string from 1 to 31 alphanumeric characters or symbols. The password is case sensitive, allows digits, English letters (case sensitive), underlines and sixteen special characters ( !$%'()*,-./[]{|} ).
7 —— Indicates a symmetric encrypted password with fixed length will follow.
encrypted-password —— A symmetric encrypted password with fixed length, which you can copy from another switch’s configuration file. After the
80
encrypted password is configured, you should use the corresponding unencrypted password if you re-enter this mode.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
User Guidelines If the password you configured here is unencrypted and the global encryption function is enabled in service password-encryption, the password in the configuration file will be displayed in the symmetric encrypted form.
Example
Add and enable a new admin user named “tplink”, of which the password is “admin” and unencrypted:
T2600G-28TS(config)#user name tplink privilege admin password 0 admin
12.2 user name (secret) Description
The user name command is used to add a new user or modify the existed users’ information. To delete the existed users, please use no user name command. This command uses the MD5 encryption.
Syntax
user name name [ privilege admin | operator | power_user | user ] secret { [ 0 ] password | 5 encrypted-password }
no user name name
Parameter
name ——Type a name for users' login, which contains 16 characters at most, composed of digits, English letters and under dashes only.
admin | operator | power_user | user —— Access level. “admin” means that you can edit, modify and view all the settings of different functions. “operator” means that you can edit, modify and view most of the the settings of different functions. “power-user” means that you can edit, modify and view some of
81
the the settings of different functions. “user” means that you can only view some of the the settings of different functions without the right to edit or modify. It is “admin” by default.
0 —— Specify the encryption type. 0 indicates that an unencrypted password will follow. By default, the encryption type is 0.
password ——Users’ login password, a string from 1 to 31 alphanumeric characters or symbols. The password is case sensitive, allows digits, English letters (case sensitive), underlines and sixteen special characters ( !$%'()*,-./[]{|} ). The password will be saved to the configuration file using the MD5 encrypted algorithm.
5 —— Indicates an MD5 encrypted password with fixed length will follow.
encrypted-password —— An MD5 encrypted password with fixed length, which you can copy from another switch’s configuration file.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
User Guidelines If both the user name (password) and user name (secret) are defined, only the latest configured password will take effect.
Example
Add and enable a new admin user named “tplink”, of which the password is “admin”. The password will be displayed in the encrypted form.
T2600G-28TS(config)#user name tplink privilege admin secret 0 admin
12.3 service password-recovery Description
The service password-recovery command is used to enable the password-recovery feature. To disable the password-recovery feature, please use no service password-recovery command.
With password-recovery enabled, you can connect to the switch’s concole port and delete all your previous set accounts. You can use the default username and password (which are both admin) to login the switch after its
82
startup. For more details about password recovery procedure, please refer to Appendix A in the User Guide.
Syntax
service password-recovery
no service password-recovery
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Enable the switch’s password recovery feature:
T2600G-28TS(config)# service password-recovery
12.4 user access-control ip-based Description
The user access-control ip-based command is used to limit the IP-range of the users for login. Only the users within the IP-range you set here are allowed to login. To cancel the user access limit, please use no user access-control command.
Syntax
user access-control ip-based { ip-addr ip-mask } [ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ]
no user access-control [ ip-based index id ]
Parameter
ip-addr —— The source IP address. Only the users within the IP-range you set here are allowed for login. 5 IP-based entries can be configured at most.
ip-mask —— The subnet mask of the IP address.
[ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ] —— Specify the access interface. These interfaces are enabled by default.
id —— Delete the specified IP-based entry. The index ranges from 1 to 5.
83
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Enable the access-control of the user whose IP address is 192.168.0.148:
T2600G-28TS(config)# user access-control ip-based 192.168.0.148
255.255.255.255
12.5 user access-control mac-based Description
The user access-control mac-based command is used to limit the MAC address of the users for login. Only the user with this MAC address you set here is allowed to login. To cancel the user access limit, please use no user access-control command.
Syntax
user access-control mac-based { mac-addr } [ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ]
no user access-control
Parameter
mac-addr —— The source MAC address. Only the user with this MAC address is allowed to login.
[ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ] —— Specify the access interface. These interfaces are enabled by default.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure that only the user whose MAC address is 00:00:13:0A:00:01 is allowed to login:
84
T2600G-28TS(config)# user access-control mac-based 00:00:13:0A:00:01
12.6 user access-control port-based Description
The user access-control port-based command is used to limit the ports for login. Only the users connected to these ports you set here are allowed to login. To cancel the user access limit, please use no user access-control command.
Syntax
user access-control port-based interface { gigabitEthernet port-list } [ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ]
no user access-control
Parameter
port-list ——The list group of Ethernet ports, in the format of 1/0/1-4. You can appoint 5 ports at most.
[ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ] —— Specify the access interface. These interfaces are enabled by default.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure that only the users connected to ports 2-6 are allowed to login:
T2600G-28TS(config)# user access-control port-based interface
gigabitEthernet 1/0/2-6
12.7 line Description
The line command is used to enter the Line Configuration Mode and make related configurations for the desired user(s), including the login mode and password configurations.
85
Syntax
line { console linenum | vty startlinenum endlinenum | ssh | telnet }
Parameter
linenum —— The number of users allowed to login through console port. Its value is 0 in general, for the reason that console input is only active on one console port at a time.
startlinenum ——The start serial number of the login user selected to configure the login mode and password, ranging from 0 to 15. 0 means the first login user number, 1 means the second, and the rest can be done on the same manner.
endlinenum —— The end serial number of the login user selected to configure the login mode and password, ranging from 0 to 15. 0 means the first login user number, 1 means the second, and the rest can be done on the same manner.
ssh —— Configure the SSH terminal line.
telnet —— Configure the Telnet terminal line.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Enter the Console port configuration mode and configure the console port 0:
T2600G-28TS(config)#line console 0
Enter the Virtual Terminal configuration mode so as to prepare further configurations such as password and login mode for virtual terminal 0 to 5:
T2600G-28TS(config)#line vty 0 5
12.8 password Description
The password command is used to configure the connection password. To clear the password, please use no password command.
86
Syntax
password { [ 0 ] password | 7 encrypted-password }
no password
Parameter
0 —— Specify the encryption type. 0 indicates that an unencrypted password will follow. By default, the encryption type is 0.
password —— Connection password, a string from 1 to 31 alphanumeric characters or symbols. The password is case sensitive, allows spaces but ignores leading spaces, and cannot contain question marks. By default, it is empty.
7 —— Indicates a symmetric encrypted password with fixed length will follow.
encrypted-password —— A symmetric encrypted password with fixed length, which you can copy from another switch’s configuration file. After the encrypted password is configured, you should use the corresponding unencrypted password if you re-enter this mode.
Command Mode
Line Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
User Guidelines If the password you configured here is unencrypted and the global encryption function is enabled in service password-encryption, the password in the configuration file will be displayed in the symmetric encrypted form.
Example
Configure the connection password of Console port connection 0 as “tplink” and unencrypted:
T2600G-28TS(config)#line console 0
T2600G-28TS(config-line)#password 0 tplink
Configure the connection password of virtual terminal connection 0-5 as “tplink” and unencrypted:
T2600G-28TS(config)#line vty 0 5
T2600G-28TS(config-line)#password 0 tplink
87
12.9 login Description
The login command is used to configure the login mode of a switch which uses connection password to login. At this situation, a connection password must be set for virtual terminal connection.
Syntax
login
Command Mode
Line Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the login of Console port connection 0 as login mode:
T2600G-28TS(config)#line console 0
T2600G-28TS(config-line)#login
Configure the login of virtual terminal connection 0-5 as login mode:
T2600G-28TS(config)#line vty 0 5
T2600G-28TS(config-line)#login
12.10 login local Description
The login local command is used to configure the login mode of the switch which uses the user name and password to login.
Syntax
login local
Command Mode
Line Configuration Mode
88
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the login of virtual terminal connection 0-5 as login local mode:
T2600G-28TS(config)#line vty 0 5
T2600G-28TS(config-line)#login local
Configure the login of Console port connection 0 as login local mode:
T2600G-28TS(config)#line console 0
T2600G-28TS(config-line)#login local
12.11 media-type rj45 Description
The media-type rj45 command is used to configure the console media type as RJ-45 for input. The switch has two console ports available —— an RJ-45 console port and a micro-USB console port. Console input is active on only one console port at a time. By default, the micro-USB connector takes precedence over the RJ-45 connector, which means that, when both the RJ-45 console connection and micro-USB console connection are valid, input from the RJ-45 console is disabled, and input from the micro-USB console is enabled. To return to the default configuration, please use no media-type rj45 command.
Syntax
media-type rj45
no media-type rj45
Command Mode Line Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Enable the RJ-45 console input:
T2600G-28TS(config)# line console 0
T2600G-28TS(config-line)# media-type rj45
89
Receive the micro-USB console input prior to the RJ-45 console input:
T2600G-28TS(config)# line console 0
T2600G-28TS(config-line)# no media-type rj45
12.12 telnet Description
The telnet enable command is used to enable the Telnet function. To disable the Telnet function, please use the telnet disable command. This function is enabled by default.
Syntax
telnet enable
telnet disable
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Disable the Telnet function:
T2600G-28TS(config)# telnet disable
12.13 serial_port baud-rate Description
The serial_port baud-rate command is used to configure the communication baud rate on the console port. To return to the default baud rate, please use no serial_port command.
Syntax
serial_port baud-rate { 9600 | 19200 | 38400 | 57600 | 115200 }
no serial_port
Parameter
9600 | 19200 | 38400 | 57600 | 115200 ——Specify the communication baud rate on the console port. The default baul rate is 38400 bps.
90
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Specify the communication baud rate on the console port to the default value:
T2600G-28TS(config)# no serial_port
12.14 show password-recovery Description
The show password-recovery command is used to display the status of the password-recovery feature.
Syntax
show password-recovery
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the status of the password-recovery feature:
T2600G-28TS(config)# show password-recovery
12.15 show user account-list Description
The show user account-list command is used to display the information of the current users.
Syntax
show user account-list
91
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the information of the current users:
T2600G-28TS(config)# show user account-list
12.16 show user configuration Description
The show user configuration command is used to display the security configuration information of the users, including access-control, max-number and the idle-timeout, etc.
Syntax
show user configuration
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the security configuration information of the users:
T2600G-28TS(config)# show user configuration
12.17 show telnet-status Description
The show telnet-status command is used to display the configuration information of the Telnet function.
Syntax
show telnet-status
92
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display whether the Telnet function is enabled:
T2600G-28TS(config)# show telnet-status
93
Chapter 13 HTTP and HTTPS Commands
With the help of HTTP (HyperText Transfer Protocol) or HTTPS (Hyper Text Transfer Protocol over Secure Socket Layer), you can manage the switch through a standard browser. HTTP is the protocol to exchange or transfer hypertext. SSL (Secure Sockets Layer), a security protocol, is to provide a secure connection for the application layer protocol (e.g. HTTP) based on TCP. Adopting asymmetrical encryption technology, SSL uses key pair to encrypt/decrypt information. A key pair refers to a public key (contained in the certificate) and its corresponding private key. By default the switch has a certificate (self-signed certificate) and a corresponding private key. The Certificate/Key Download function enables the user to replace the default key pair.
13.1 ip http server Description
The ip http server command is used to enable the HTTP server within the switch. To disable the HTTP function, please use no ip http server command. This function is enabled by default. The HTTP and HTTPS server function cannot be disabled at the same time.
Syntax
ip http server
no ip http server
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Disable the HTTP function:
T2600G-28TS(config)# no ip http server
94
13.2 ip http max-users (For T2600G-18TS only) Description
The ip http max-users command is used to configure the maximum number of users that are allowed to connect to the HTTP server. To cancel this limitation, please use no ip http max-users command.
Syntax
ip http max-users admin-num operator-num poweruser-num user-num
no ip http max-users
Parameter
admin-num —— The maximum number of the users logging on to the HTTP server as Admin, ranging from 1 to 16. The total number of users should be no more than 16.
operator-num —— The maximum number of the users logging on to the HTTP server as Operator, ranging from 0 to 15.The total number of users should be less than 16.
poweruser-num—— The maximum number of the users logging on to the HTTP server as Power User, ranging from 0 to 15.The total number of users should be less than 16.
user-num—— The maximum number of the users logging on to the HTTP server as User, ranging from 0 to 15.The total number of users should be less than 16.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure the maximum number of the Admin, Operator, Power User and User users logging on to the HTTP server as 5, 3, 2 and 3:
T2600G-18TS(config)# ip http max-users 5 3 2 3
95
13.3 ip http max-users (For other switches) Description
The ip http max-users command is used to configure the maximum number of users that are allowed to connect to the HTTP server. To cancel this limitation, please use no ip http max-users command.
Syntax
ip http max-users admin-num guest-num
no ip http max-users
Parameter
admin-num —— The maximum number of the users logging on to the HTTP server as Admin, ranging from 1 to 16. The total number of Admin and Guest should be less than 16.
guest-num —— The maximum number of the users logging on to the HTTP server as Guest, ranging from 0 to 15.The total number of Admin and Guest should be less than 16.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure the maximum number of the Admin and Guest users logging on to the HTTP server as 5 and 3:
T2600G-28TS(config)# ip http max-users 5 3
13.4 ip http session timeout Description
The ip http session timeout command is used to configure the connection timeout of the HTTP server. To restore to the default timeout time, please use no ip http session timeout command.
Syntax
ip http session timeout time
96
no ip http session timeout
Parameter
time ——The timeout time, ranging from 5 to 30 in minutes. By default, the value is 10.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure the timeout time of the HTTP connection as 15 minutes:
T2600G-28TS(config)# ip http session timeout 15
13.5 ip http secure-server Description
The ip http secure-server command is used to enable the HTTPS server within the switch. To disable the HTTPS function, please use no ip http secure-server command. This function is enabled by default. The HTTP and HTTPS server function cannot be disabled at the same time.
Syntax
ip http secure-server
no ip http secure-server
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Disable the HTTP function:
T2600G-28TS(config)# no ip http secure-server
97
13.6 ip http secure-protocol Description
The ip http secure-protocol command is used to configure the SSL protocol version. To restore to the default SSL version, please use no ip http secure-protocol command. By default, the switch supports SSLv3 and TLSv1.
Syntax
ip http secure-protocol { [ ssl3 ] [ tls1 ] }
no ip http session
Parameter
ssl3 —— The SSL 3.0 protocol.
tls1 —— The TLS 1.0 protocol
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the protocol of SSL connection as SSL 3.0:
T2600G-28TS(config)# ip http secure-protocol ssl3
13.7 ip http secure-ciphersuite Description
The ip http secure-ciphersuite command is used to configure the cipherSuites over the SSL connection supported by the switch. To restore to the default ciphersuite types, please use no ip http secure-ciphersuite command.
Syntax
ip http secure-ciphersuite { [ 3des-ede-cbc-sha ] [ rc4-128-md5 ] [ rc4-128-sha ] [ des-cbc-sha ] }
no ip http secure-ciphersuite
98
Parameter
[ 3des-ede-cbc-sha ] [ rc4-128-md5 ] [ rc4-128-sha ] [ des-cbc-sha ] —— Specify the encryption algorithm and the digest algorithm to use on an SSL connection. By default, the switch supports all these ciphersuites.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the ciphersuite to be used for encryption over the SSL connection as 3des-ede-cbc-sha:
T2600G-28TS(config)# ip http secure-ciphersuite 3des-ede-cbc-sha
13.8 ip http secure-max-users Description
The ip http secure-max-users command is used to configure the maximum number of users that are allowed to connect to the HTTPs server. To cancel this limitation, please use no ip http secure-max-users command.
Syntax
ip http secure-max-users admin-num guest-num
no ip secure-max-users
Parameter
admin-num —— The maximum number of the users logging on to the HTTPs server as Admin, ranging from 1 to 16. The total number of Admin and Guest should be less than 16.
guest-num —— The maximum number of the users logging on to the HTTPs server as Guest, ranging from 0 to 15.The total number of Admin and Guest should be less than 16.
Command Mode
Global Configuration Mode
99
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the maximum number of the Admin and Guest users logging on to the HTTPs server as 5 and 3:
T2600G-28TS(config)# ip http secure-max-users 5 3
13.9 ip http secure-session timeout Description
The ip http secure-session timeout command is used to configure the connection timeout of the HTTPS server. To restore to the default timeout time, please use no ip http secure-session timeout command.
Syntax
ip http secure-session timeout time
no ip http secure-session timeout
Parameter
time —— The timeout time, ranging from 5 to 30 in minutes. By default, the value is 10.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the timeout time of the HTTPs connection as 15 minutes:
T2600G-28TS(config)# ip http secure-session timeout 15
100
13.10 ip http secure-server download certificate Description
The ip http secure-server download certificate command is used to download a certificate to the switch from TFTP server.
Syntax
ip http secure-server download certificate ssl-cert ip-address ip-addr
Parameter ssl-cert —— The name of the SSL certificate which is selected to download to the switch. The length of the name ranges from 1 to 25 characters. The Certificate must be BASE64 encoded.
ip-addr —— The IP address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Download an SSL Certificate named ssl-cert from TFTP server with the IP address of 192.168.0.146:
T2600G-28TS(config)# ip http secure-server download certificate ssl-cert
ip-address 192.168.0.146
Download an SSL Certificate named ssl-cert from TFTP server with the IP address of fe80::1234
T2600G-28TS(config)# ip http secure-server download certificate ssl-cert
ip-address fe80::1234
101
13.11 ip http secure-server download key Description
The ip http secure-server download key command is used to download an SSL key to the switch from TFTP server.
Syntax
ip http secure-server download key ssl-key ip-address ip-addr
Parameter ssl-key —— The name of the SSL key which is selected to download to the switch. The length of the name ranges from 1 to 25 characters. The Key must be BASE64 encoded.
ip-addr —— The IP address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Download an SSL key named ssl-key from TFTP server with the IP address of 192.168.0.146:
T2600G-28TS(config)# ip http secure-server download key ssl-key
ip-address 192.168.0.146
Download an SSL key named ssl-key from TFTP server with the IP address of fe80::1234
T2600G-28TS(config)# ip http secure-server download key ssl-key
ip-address fe80::1234
102
13.12 show ip http configuration Description
The show ip http configuration command is used to display the configuration information of the HTTP server, including status, session timeout, access-control, max-user number and the idle-timeout, etc.
Syntax
show ip http configuration
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configuration information of the HTTP server:
T2600G-28TS(config)# show ip http configuration
13.13 show ip http secure-server Description
The show ip http secure-server command is used to display the global configuration of SSL.
Syntax
show ip http secure-server
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the global configuration of SSL:
T2600G-28TS(config)# show ip http secure-server
103
Chapter 14 ARP Commands
Address Resolution Protocol (ARP) is used to resolve an IP address into an Ethernet MAC address. The swich maintains an ARP mapping table to record the IP-to-MAC mapping relations, which is used for forwarding packets. An ARP mapping table contains two types of ARP entries: dynamic and static. An ARP dynamic entry is automatically created and maintained by ARP. A static ARP entry is manually configured and maintained.
14.1 arp Description
This arp command is used to add a static ARP entry. To delete the specified ARP entry, please use the no arp command.
Syntax
arp ip mac type
no arp ip type
Parameter
ip —— The IP address of the static ARP entry.
mac —— The MAC address of the static ARP entry.
type —— The ARP type. Configure it as “arpa”.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create a static ARP entry with the IP as 192.168.0.1 and the MAC as 00:11:22:33:44:55:
T2600G-28TS(config)# arp 192.168.0.1 00:11:22:33:44:55 arpa
104
14.2 clear arp-cache Description
This clear arp-cache command is used to clear all the dynamic ARP entries.
Syntax
clear arp-cache
Command Mode
Privileged EXEC Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Clear all the dynamic ARP entries:
T2600G-28TS(config)# clear arp-cache
14.3 arp timeout Description
This arp timeout command is used to configure the ARP aging time of the interface.
Syntax
arp timeout timeout
no arp timeout
Parameter
timeout —— Specify the aging time, ranging from 1 to 3000 seconds. The default value is 600 seconds.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
105
Example
Configure the ARP aging time as 60 seconds on interface 1/0/1:
T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)# arp timeout 60
14.4 show arp Description
This show arp command is used to display the active ARP entries. If no parameter is speicified, all the active ARP entries will be displayed.
Syntax
show arp [ ip ] [ mac ]
show ip arp [ ip ] [ mac ]
Parameter
ip —— Specify the IP address of your desired ARP entry.
mac —— Specify the MAC address of your desired ARP entry.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the ARP entry with the IP as 192.168.0.2:
T2600G-28TS(config)# show ip arp 192.168.0.2
14.5 show ip arp (interface) Description
This show arp command is used to display the active ARP entries associated with a specified Layer 3 interface.
Syntax
show ip arp { gigabitEthernet port | port-channel port-channel-id | vlan id }
106
Parameter
port —— Specify the number of the routed port.
port-channel-id —— Specify the ID of the port channel.
id —— Specify the VLAN interface ID.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the ARP entry associated with VLAN interface 2 :
T2600G-28TS(config)# show ip arp vlan 2
14.6 show ip arp summary Description
This show ip arp summary command is used to display the number of the active ARP entries.
Syntax
show ip arp summary
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the number of the ARP entries:
T2600G-28TS(config)# show ip arp summary
107
Chapter 15 Binding Table Commands
You can bind the IP address, MAC address, VLAN and the connected Port number of the Host together, which can be the condition for the ARP Inspection and IP verify source to filter the packets.
15.1 ip source binding Description
The ip source binding command is used to bind the IP address, MAC address, VLAN ID and the Port number together manually. You can manually bind the IP address, MAC address, VLAN ID and the Port number together in the condition that you have got the related information of the Hosts in the LAN. To delete the IP-MAC–VID-PORT entry from the binding table, please use no ip source binding index command.
Syntax
ip source binding hostname ip-addr mac-addr vlan vlan-id interface gigabitEthernet port { none | arp-detection | ip-verify-source | both } [ forced-source { arp-scanning | dhcp-snooping } ]
no ip source binding index idx
Parameter
hostname ——The Host Name, which contains 20 characters at most.
ip-addr —— The IP address of the Host.
mac-addr —— The MAC address of the Host.
vlan-id ——The VLAN ID needed to be bound, ranging from 1 to 4094.
port —— The number of port connected to the Host.
none | arp-detection | ip-verify-source | both ——The protect type for the entry. “arp-detection” indicates ARP detection; “ip-verify-source” indicates IP source filter; “none” indicates applying none; “both” indicates applying both.
forced-source —— The source of the binding entry can be specified as “arp-scanning” or “dhcp-snooping”. It is multi-optional.
idx —— The entry number needed to be deleted. You can use the show ip source binding command to get the idx. Pay attention that the entry number
108
is the actual number in the binding table which is not display in an arranged order.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Bind an ACL entry with the IP 192.168.0.1, MAC 00:00:00:00:00:01, VLAN ID 2 and the Port number 5 manually. And then enable the entry for the ARP detection:
T2600G-28TS(config)#ip source binding host1 192.168.0.1
00:00:00:00:00:01 vlan 2 interface gigabitEthernet 1/0/5 arp-detection
Delete the IP-MAC–VID-PORT entry with the index 5:
T2600G-28TS(config)#no ip source binding index 5
15.2 ip dhcp snooping Description
The ip dhcp snooping command is used to enable DHCP Snooping function globally. To disable DHCP Snooping function globally, please use no ip dhcp snooping command. DHCP Snooping functions to monitor the process of the Host obtaining the IP address from DHCP server, and record the IP address, MAC address, VLAN and the connected Port number of the Host for automatic binding. The switch can also propagate the control information and the network parameters via the Option 82 field to provide more information for the Host.
Syntax
ip dhcp snooping
no ip dhcp snooping
Command Mode
Global Configuration Mode
109
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the DHCP Snooping function globally:
T2600G-28TS(config)#ip dhcp snooping
15.3 ip dhcp snooping vlan Description
The ip dhcp snooping vlan command is used to enable DHCP Snooping function on a specified VLAN. To disable DHCP Snooping function on this VLAN, please use no ip dhcp snooping vlan command.
Syntax
ip dhcp snooping vlan vlan-range
no ip dhcp snooping vlan vlan-range
Parameter
vlan-range —— Specify the VLANs to enable the DHCP snooping function, in the format of 1-3, 5.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the DHCP Snooping function on VLAN 1,4,6-7:
T2600G-28TS(config)#ip dhcp snooping vlan 1,4,6-7
110
15.4 ip dhcp snooping information option Description
The ip dhcp snooping information option command is used to enable the Option 82 function of DHCP Snooping. To disable the Option 82 function, please use no ip dhcp snooping information option command.
Syntax
ip dhcp snooping information option
no ip dhcp snooping information option
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the Option 82 function of DHCP Snooping on port 1/0/1:
T2600G-28TS(config)#interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)#ip dhcp snooping information option
15.5 ip dhcp snooping information strategy Description
The ip dhcp snooping information strategy command is used to select the operation for the Option 82 field of the DHCP request packets from the Host. To restore to the default option, please use no ip dhcp snooping information strategy command.
Syntax
ip dhcp snooping information strategy strategy
no ip dhcp snooping information strategy
111
Parameter
strategy —— The operations for Option 82 field of the DHCP request packets from the Host, including three types:
keep: Indicates to keep the Option 82 field of the packets. It is the default option;
replace: Indicates to replace the Option 82 field of the packets with the switch defined one;
drop: Indicates to discard the packets including the Option 82 field
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Replace the Option 82 field of the packets with the switch defined one and then send out on port 1/0/1:
T2600G-28TS(config)#interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)#ip dhcp snooping information strategy replace
15.6 ip dhcp snooping information format Description
The ip dhcp snooping information format command is used to select the format of option 82 sub-option value field. To restore to the default option, please use no ip dhcp snooping information format command.
Syntax
ip dhcp snooping information format { normal | private }
no ip dhcp snooping information format
Parameter
normal | private —— The format type of option 82 sub-option value field.
normal: Indicates that the format of sub-option value field is TLV (type-length-value).
112
private: Indicates that the format of sub-option value field is the value you configure for the related sub-option.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Select the format of option 82 sub-option value field as TLV (type-length-value) on port 1/0/1:
T2600G-28TS(config)#interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)#ip dhcp snooping information format normal
15.7 ip dhcp snooping information remote-id Description
The ip dhcp snooping information remote-id command is used to configure the customized sub-option Remote ID for the Option 82. To return to default Remote ID for the Option 82, please use no ip dhcp snooping information remote-id command.
Syntax
ip dhcp snooping information remote-id string
no ip dhcp snooping information remote-id
Parameter
string —— Enter the sub-option Remote ID, which contains 64 characters at most.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
113
Example
Configure the customized sub-option Remote ID for the Option 82 as tplink on port 1/0/1:
T2600G-28TS(config)#interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)#ip dhcp snooping information remote-id tplink
15.8 ip dhcp snooping information circuit-id Description
The ip dhcp snooping information circuit-id command is used to enable and configure the customized sub-option Circuit ID for the Option 82 on a specified port/port channel. To return to the default Circuit ID for the Option 82, please use no ip dhcp snooping information circuit-id command.
Syntax
ip dhcp snooping information circuit-id string
no ip dhcp snooping information circuit-id
Parameter
string —— Enter the sub-option Circuit ID, which contains 64 characters at most.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable and configure the customized sub-option Circuit ID for the Option 82 as “tplink” on port 1/0/1:
T2600G-28TS(config)#interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)#ip dhcp snooping information circuit-id tplink
114
15.9 ip dhcp snooping trust Description
The ip dhcp snooping trust command is used to configure a port to be a Trusted Port. Only the Trusted Port can receive the DHCP packets from DHCP servers. To turn the port back to a distrusted port, please use no ip dhcp snooping trust command.
Syntax
ip dhcp snooping trust
no ip dhcp snooping trust
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the Gigabit Ethernet port 1/0/2 to be a Trusted Port:
T2600G-28TS(config)#interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)#ip dhcp snooping trust
15.10 ip dhcp snooping mac-verify Description
The ip dhcp snooping mac-verify command is used to enable the MAC Verify feature. To disable the MAC Verify feature, please use no ip dhcp snooping mac-verify command. There are two fields of the DHCP packet containing the MAC address of the Host. The MAC Verify feature is to compare the two fields and discard the packet if the two fields are different.
Syntax
ip dhcp snooping mac-verify
no ip dhcp snooping mac-verify
115
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the MAC Verify feature for the Gigabit Ethernet port 10/2:
T2600G-28TS(config)#interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)#ip dhcp snooping mac-verify
15.11 ip dhcp snooping limit rate Description
The ip dhcp snooping limit rate command is used to enable the Flow Control feature for the DHCP packets. The excessive DHCP packets will be discarded. To restore to the default configuration, please use no ip dhcp snooping limit rate command.
Syntax
ip dhcp snooping limit rate value
no ip dhcp snooping limit rate
Parameter
value —— The value of Flow Control. The options are 5/10/15/20/25/30 (packet/second). The default value is 0, which stands for “disable”.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Set the Flow Control of GigabitEthernet port 2 as 20 pps:
116
T2600G-28TS(config)#interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)#ip dhcp snooping limit rate 20
15.12 ip dhcp snooping decline rate Description
The ip dhcp snooping decline rate command is used to enable the Decline Protect feature and configure the rate limit on DHCP Decine packets. The excessive DHCP Decline packets will be discarded. To disable the Decline Protect feature, please use no ip dhcp snooping decline rate command.
Syntax
ip dhcp snooping decline rate value
no ip dhcp snooping decline rate
Parameter
value —— Specify the rate limit of DHCP Decline packets, and the optional values are 0, 5, 10, 15, 20, 25 and 30 (units:packet/second). It default value is 0, which stands for “disable”.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the rate limit of DHCP Decline packets as 20 packets per second on Gigabit Ethernet port 1/0/2:
T2600G-28TS(config)#interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)#ip dhcp snooping decline 20
117
15.13 show ip source binding Description
The show ip source binding command is used to display the IP-MAC-VID- PORT binding table.
Syntax
show ip source binding
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the IP-MAC-VID-PORT binding table:
T2600G-28TS(config)#show ip source binding
15.14 show ip dhcp snooping Description
The show ip dhcp snooping command is used to display the running status of DHCP Snooping.
Syntax
show ip dhcp snooping
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the running status of DHCP Snooping:
T2600G-28TS#show ip dhcp snooping
118
15.15 show ip dhcp snooping interface Description
The show ip dhcp snooping interface command is used to display the DHCP Snooping configuration of a desired Gigabit Ethernet port/port channel or of all Ethernet ports/port channels.
Syntax
show ip dhcp snooping interface [ gigabitEthernet port | port-channel port-channel-id ]
Parameters
port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the DHCP Snooping configuration of all Ethernet ports and port channels:
T2600G-28TS#show ip dhcp snooping interface
Display the DHCP Snooping configuration of Gigabit Ethernet port 1/0/5:
T2600G-28TS#show ip dhcp snooping interface gigabitEthernet 1/0/5
15.16 show ip dhcp snooping information interface Description
The show ip dhcp snooping information interface command is used to display the DHCP snooping option 82 configuration of a desired Gigabit Ethernet port/port channel or of all Ethernet ports/port channels.
Syntax
show ip dhcp snooping information interface [ gigabitEthernet port | port-channel port-channel-id ]
119
Parameters
port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the DHCP snooping option 82 configuration of all Ethernet ports and port channels:
T2600G-28TS#show ip dhcp snooping information interface
Display the DHCP snooping option 82 configuration of Gigabit Ethernet port 1/0/5:
T2600G-28TS#show ip dhcp snooping information interface
gigabitEthernet 1/0/5
120
Chapter 16 IPv6 Binding Table Commands
You can bind the IPv6 address, MAC address, VLAN and the connected Port number of the Host together, which can be the condition for the ND Detection and IPv6 Source Guard to filter the packets.
16.1 ipv6 source binding Description
The ipv6 source binding command is used to bind the IPv6 address, MAC address, VLAN ID and the Port number together manually. You can manually bind the IPv6 address, MAC address, VLAN ID and the Port number together in the condition that you have got the related information of the Hosts in the LAN. To delete the IPv6-MAC–VID-PORT entry from the binding table, please use no ipv6 source binding index command.
Syntax
ipv6 source binding hostname ipv6-addr mac-addr vlan vlan-id interface gigabitEthernet port { none | nd-detection | ipv6-verify-source | both }
no ipv6 source binding index idx
Parameter
hostname ——The Host Name, which contains 20 characters at most.
ipv6-addr —— The IPv6 address of the Host.
mac-addr —— The MAC address of the Host.
vlan-id ——The VLAN ID needed to be bound, ranging from 1 to 4094.
port —— The number of port connected to the Host.
none | nd-detection | ipv6-verify-source | both ——The protect type for the entry. “nd-detection” indicates ND Detection; “ipv6-verify-source” indicates IPv6 Source Guard; “none” indicates applying none; “both” indicates applying both.
idx —— The entry number needed to be deleted. You can use the show ipv6 source binding command to get the idx. Pay attention that the entry number is the actual number in the binding table which is not display in an arranged order.
121
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Bind an ACL entry with the IP 2001::1, MAC 00:00:00:00:00:01, VLAN ID 2 and the Port number 5 manually. And then enable the entry for the ND Detection:
T2600G-28TS(config)#ipv6 source binding host1 2001::1
00:00:00:00:00:01 vlan 2 interface gigabitEthernet 1/0/5 nd-detection
Delete the IPv6-MAC–VID-PORT entry with the index 5:
T2600G-28TS(config)#no ipv6 source binding index 5
16.2 ipv6 dhcp snooping Description
The ipv6 dhcp snooping command is used to enable DHCPv6 Snooping function globally. To disable DHCPv6 Snooping function globally, please use no ipv6 dhcp snooping command. DHCP Snooping functions to monitor the process of the Host obtaining the IPv6 address from DHCPv6 server, and record the IPv6 address, MAC address, VLAN and the connected Port number of the Host for automatic binding.
Syntax
ipv6 dhcp snooping
no ipv6 dhcp snooping
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
122
Example
Enable the DHCPv6 Snooping function globally:
T2600G-28TS(config)#ipv6 dhcp snooping
16.3 ipv6 dhcp snooping vlan Description
The ipv6 dhcp snooping vlan command is used to enable DHCPv6 Snooping function on a specified VLAN. To disable DHCPv6 Snooping function on this VLAN, please use no ipv6 dhcp snooping vlan command.
Syntax
ipv6 dhcp snooping vlan vlan-range
no ipv6 dhcp snooping vlan vlan-range
Parameter
vlan-range —— Specify the VLANs to enable the DHCPv6 snooping function, in the format of 1-3, 5.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the DHCPv6 Snooping function on VLAN 1,4,6-7:
T2600G-28TS(config)#ipv6 dhcp snooping vlan 1,4,6-7
16.4 ipv6 dhcp snooping trust Description
The ipv6 dhcp snooping trust command is used to configure a port to be a Trusted Port. Only the Trusted Port can forward the DHCPv6 packets from DHCPv6 servers. To turn the port back to a distrusted port, please use no ipv6 dhcp snooping trust command.
123
Syntax
ipv6 dhcp snooping trust
no ipv6 dhcp snooping trust
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the Gigabit Ethernet port 1/0/2 to be a Trusted Port:
T2600G-28TS(config)#interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)#ipv6 dhcp snooping trust
16.5 ipv6 nd snooping Description
The ipv6 nd snooping command is used to enable ND Snooping function globally. To disable ND Snooping function globally, please use no ipv6 nd snooping command. ND Snooping functions to monitor the process of the duplication address detection, And record the IPv6 address, MAC address, VLAN and the connected Port number of the Host for automatic binding.
Syntax
ipv6 nd snooping
no ipv6 nd snooping
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the ND Snooping function globally:
124
T2600G-28TS(config)#ipv6 nd snooping
16.6 ipv6 nd snooping vlan Description
The ipv6 nd snooping vlan command is used to enable ND Snooping function on a specified VLAN. To disable ND Snooping function on this VLAN, please use no ipv6 nd snooping vlan command.
Syntax
ipv6 nd snooping vlan vlan-range
no ipv6 nd snooping vlan vlan-range
Parameter
vlan-range —— Specify the VLANs to enable the ND snooping function, in the format of 1-3, 5.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the ND Snooping function on VLAN 1,4,6-7:
T2600G-28TS(config)#ipv6 nd snooping vlan 1,4,6-7
16.7 ipv6 nd snooping max-entries Description
The ipv6 nd snooping max-entries command is used to specify the maximum number of binding entries that are allow to be binded to a port. To return the default, please use no ipv6 nd snooping max-entries command.
Syntax
ipv6 nd snooping max-entries value
no ipv6 nd snooping max-entries
125
Parameter
value —— Specify the maximum number of ND snooping entries on this interface.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the maximum number of binding entries from ND Snooping of Gigabit Ethernet port 1/0/2 is 100:
T2600G-28TS(config)#interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)#ipv6 nd snooping max-entries 100
16.8 show ipv6 source binding Description
The show ipv6 source binding command is used to display the IPv6-MAC-VID- PORT binding table.
Syntax
show ipv6 source binding
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the IPv6-MAC-VID-PORT binding table:
T2600G-28TS(config)#show ipv6 source binding
126
16.9 show ipv6 dhcp snooping Description
The show ipv6 dhcp snooping command is used to display the running status of DHCPv6 Snooping.
Syntax
show ipv6 dhcp snooping
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the running status of DHCPv6 Snooping:
T2600G-28TS#show ipv6 dhcp snooping
16.10 show ipv6 dhcp snooping interface Description
The show ipv6 dhcp snooping interface command is used to display the DHCPv6 Snooping configuration of a desired Gigabit Ethernet port/port channel or of all Ethernet ports/port channels.
Syntax
show ipv6 dhcp snooping interface [ gigabitEthernet port | port-channel port-channel-id ]
Parameters
port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
127
Example
Display the DHCPv6 Snooping configuration of all Ethernet ports and port channels:
T2600G-28TS#show ipv6 dhcp snooping interface
Display the DHCPv6 Snooping configuration of Gigabit Ethernet port 1/0/5:
T2600G-28TS#show ipv6 dhcp snooping interface gigabitEthernet 1/0/5
16.11 show ipv6 nd snooping Description
The show ipv6 nd snooping command is used to display the running status of ND Snooping.
Syntax
show ipv6 nd snooping
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the running status of ND Snooping:
T2600G-28TS#show ipv6 nd snooping
16.12 show ipv6 nd snooping interface Description
The show ipv6 nd snooping interface command is used to display the ND Snooping configuration of a desired Gigabit Ethernet port/port channel or of all Ethernet ports/port channels.
Syntax
show ipv6 nd snooping interface [ gigabitEthernet port | port-channel port-channel-id ]
128
Parameters
port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the ND Snooping configuration of all Ethernet ports and port channels:
T2600G-28TS#show ipv6 nd snooping interface
Display the ND Snooping configuration of Gigabit Ethernet port 1/0/5:
T2600G-28TS#show ipv6 nd snooping interface gigabitEthernet 1/0/5
129
Chapter 17 IP Verify Source Commands
IP Verify Source is to filter the IP packets based on the IP-MAC Binding entries. Only the packets matched to the IP-MAC Binding rules can be processed, which can enhance the bandwidth utility.
17.1 ip verify source Description
The ip verify source command is used to configure the IP Verify Source mode for a specified port. To disable the IP Verify Source function, please use no ip verify source command.
Syntax
ip verify source { sip+mac }
no ip verify source
Parameter
sip+mac —— Security type. “sip+mac” indicates that only the packets with its source IP address, source MAC address and port number matched to the IP-MAC binding rules can be processed.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the IP Verify Source function for Gigabit Ethernet ports 5-10. Configure that only the packets with its source IP address, source MAC address and port number matched to the IP-MAC binding rules can be processed:
T2600G-28TS(config)#interface range gigabitEthernet 1/0/5-10
T2600G-28TS(config-if-range)#ip verify source sip+mac
130
17.2 show ip verify source
Description
The show ip verify source command is used to display the IP Verify Source configuration information.
Syntax
show ip verify source
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the IP Verify Source configuration information:
T2600G-28TS(config)#show ip verify source
17.3 show ip verify source interface Description
The show ip verify source interface command is used to display the IP verify source configuration of a desired Gigabit Ethernet port.
Syntax
show ip verify source interface gigabitEthernet port
Parameters
port —— The Ethernet port number.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
131
Example
Display the IP verify source configuration of Gigabit Ethernet port 1/0/5:
T2600G-28TS#show ip verify source interface gigabitEthernet 1/0/5
132
Chapter 18 IPv6 Verify Source Commands
IPv6 Verify Source is to filter the IPv6 packets based on the IPv6-MAC Binding entries. Only the packets matched to the IPv6-MAC Binding rules can be processed, which can enhance the bandwidth utility.
Before configuring IPv6 Verify Source feature, you should configure the SDM template as “enterpriseV6” and save your configurations. For more information about SDM configuration, please refer to sdm prefer.
18.1 ipv6 verify source Description
The ipv6 verify source command is used to configure the IPv6 Verify Source mode for a specified port. To disable the IPv6 Verify Source function, please use no ipv6 verify source command.
Syntax
ipv6 verify source { sipv6+mac }
no ipv6 verify source
Parameter
sipv6+mac —— Security type. “sipv6+mac” indicates that only the packets with its source IPv6 address, source MAC address and port number matched to the IPv6-MAC binding rules can be processed.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet )
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the IPv6 Verify Source function for Gigabit Ethernet ports 5-10. Configure that only the packets with its source IPv6 address, source MAC address and port number matched to the IPv6-MAC binding rules can be processed:
133
T2600G-28TS(config)#interface range gigabitEthernet 1/0/5-10
T2600G-28TS(config-if-range)#ipv6 verify source sipv6+mac
18.2 show ipv6 verify source
Description
The show ipv6 verify source command is used to display the IPv6 Verify Source configuration information.
Syntax
show ipv6 verify source
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the IPv6 Verify Source configuration information:
T2600G-28TS(config)#show ipv6 verify source
18.3 show ipv6 verify source interface Description
The show ipv6 verify source interface command is used to display the IPv6 verify source configuration of a desired Gigabit Ethernet port.
Syntax
show ipv6 verify source interface gigabitEthernet port
Parameters
port —— The Ethernet port number.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
134
Privilege Requirement
None.
Example
Display the IPv6 verify source configuration of Gigabit Ethernet port 1/0/5:
T2600G-28TS#show ipv6 verify source interface gigabitEthernet 1/0/5
135
Chapter 19 ND Detection Commands
The ND Detection feature allows the switch to detect the ND packets based on the binding entries in the IPv6-MAC Binding Table and filter out the illegal ND packets. Before configuring ND Detection, complete IPv6-MAC Binding configuration. For details, refer to IPv6-MAC Binding Configurations.
19.1 ipv6 nd detection Description
The ipv6 nd detection command is used to enable the ND Detection function globally. To disable the ND Detection function, please use no ipv6 nd detection command.
Syntax
Ipv6 nd detection
no ipv6 nd detection
Command Mode
Global Configuration Mode
Example
Enable the ND Detection function globally:
T2600G-28TS(config)#ipv6 nd detection
19.2 ipv6 nd detection vlan Description
The ipv6 nd detection vlan command is used to enable ND Detection function on a specified VLAN. To disable ND Detection function on this VLAN, please use no ipv6 nd detection vlan command.
Syntax
ipv6 nd detection vlan vlan-range
no ipv6 nd detection vlan vlan-range
136
Parameter
vlan-range ——Enter the vlan range in the format of 1-3, 5.
Command Mode
Global Configuration Mode
Example
Enable the ND Detection function on VLAN 1,4,6-7:
T2600G-28TS(config)#ipv6 nd detection vlan 1,4,6-7
19.3 ipv6 nd detection trust Description
The ipv6 nd detection trust command is used to configure the port for which the ND Detection function is unnecessary as the Trusted Port. To clear the Trusted Port list, please use no ipv6 nd detection trust command .The specific port, such as up-linked port, routing port and LAG port, should be set as Trusted Port. To ensure the normal communication of the switch, please configure the ND Detection Trusted Port before enabling the ND Detection function.
Syntax
Ipv6 nd detection trust
no ipv6 nd detection trust
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet/ interface port-channel / interface range port-channel)
Example
Configure the Gigabit Ethernet ports 1/0/2-5 as the Trusted Port:
T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-5
T2600G-28TS(config-if-range)#ipv6 nd detection trust
137
19.4 show ipv6 nd detection Description
The show ipv6 nd detection command is used to display the ND detection global configuration including the enable/disable status.
Syntax
show ipv6 nd detection
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Example
Display the ND Detection configuration globally:
T2600G-28TS(config)#show ipv6 nd detection
19.5 show ipv6 nd detection interface Description
The show ipv6 nd detection interface command is used to display the interface configuration of ND Detection.
Syntax
show ipv6 nd detection interface[ gigabitEthernet port | port-channel port-channel-id ]
Parameter
port ——The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
138
Example
Display the configuration of Gigabit Ethernet port 1/0/1:
T2600G-28TS(config)#show ipv6 nd detection interface gigabitEthernet
1/0/1
Display the configuration of all Ethernet ports:
T2600G-28TS(config)#show ipv6 nd detection interface
139
Chapter 20 ARP Inspection Commands
ARP (Address Resolution Protocol) Detect function is to protect the switch from the ARP cheating, such as the Network Gateway Spoofing and Man-In-The-Middle Attack, etc.
20.1 ip arp inspection(global) Description
The ip arp inspection command is used to enable the ARP Detection function globally. To disable the ARP Detection function, please use no ip arp detection command.
Syntax
ip arp inspection
no ip arp inspection
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the ARP Detection function globally:
T2600G-28TS(config)#ip arp inspection
20.2 ip arp inspection trust Description
The ip arp inspection trust command is used to configure the port for which the ARP Detect function is unnecessary as the Trusted Port. To clear the Trusted Port list, please use no ip arp detection trust command .The specific ports, such as up-linked port and routing port and LAG port, should be set as Trusted Port. To ensure the normal communication of the switch, please configure the ARP Trusted Port before enabling the ARP Detect function.
140
Syntax
ip arp inspection trust
no ip arp inspection trust
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the Gigabit Ethernet ports 1/0/2-5 as the Trusted Port:
T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-5
T2600G-28TS(config-if-range)#ip arp inspection trust
20.3 ip arp inspection(interface) Description
The ip arp inspection command is used to enable the ARP Defend function. To disable the ARP detection function, please use no ip arp inspection command. ARP Attack flood produces lots of ARP Packets, which will occupy the bandwidth and slow the network speed extremely. With the ARP Defend enabled, the switch can terminate receiving the ARP packets for 300 seconds when the transmission speed of the legal ARP packet on the port exceeds the defined value so as to avoid ARP Attack flood.
Syntax
ip arp inspection
no ip arp inspection
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
141
Example
Enable the arp defend function for the Gigabit Ethernet ports 1/0/2-6:
T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-6
T2600G-28TS(config-if-range)#ip arp inspection
20.4 ip arp inspection limit-rate Description
The ip arp inspection limit-rate command is used to configure the ARP speed of a specified port. To restore to the default speed, please use no ip arp inspection limit-rate command.
Syntax
ip arp inspection limit-rate value
no ip arp inspection limit-rate
Parameter
value ——The value to specify the maximum amount of the received ARP packets per second, ranging from 10 to 100 in pps(packet/second). By default, the value is 15.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the maximum amount of the received ARP packets per second as 50 pps for Gigabit Ethernet port 5:
T2600G-28TS(config)#interface gigabitEthernet 1/0/5
T2600G-28TS(config-if)#ip arp inspection limit-rate 50
142
20.5 ip arp inspection recover Description
The ip arp inspection recover command is used to restore a port to the ARP transmit status from the ARP filter status.
Syntax
ip arp inspection recover
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Restore Gigabit Ethernet port 1/0/5 to the ARP transmit status:
T2600G-28TS(config)#interface gigabitEthernet 1/0/5
T2600G-28TS(config-if)#ip arp inspection recover
20.6 show ip arp inspection Description
The show ip arp inspection command is used to display the ARP detection global configuration including the enable/disable status and the Trusted Port list.
Syntax
show ip arp inspection
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
143
Example
Display the ARP detection configuration globally:
T2600G-28TS(config)#show ip arp inspection
20.7 show ip arp inspection interface Description
The show ip arp inspection interface command is used to display the interface configuration of ARP detection.
Syntax
show ip arp inspection interface [ gigabitEthernet port ]
Parameter
port ——The Ethernet port number.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configuration of Gigabit Ethernet port 1/0/1:
T2600G-28TS(config)#show ip arp inspection interface gigabitEthernet
1/0/1
Display the configuration of all Ethernet ports:
T2600G-28TS(config)#show ip arp inspection interface
20.8 show ip arp inspection statistics Description
The show ip arp inspection statistics command is used to display the number of the illegal ARP packets received.
Syntax
show ip arp inspection statistics
144
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the number of the illegal ARP packets received:
T2600G-28TS(config)#show ip arp inspection statistics
20.9 clear ip arp inspection statistics Description
The clear ip arp inspection statistics command is used to clear the statistic of the illegal ARP packets received.
Syntax
clear ip arp inspection statistics
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Clear the statistic of the illegal ARP packets received:
T2600G-28TS(config)#clear ip arp inspection statistics
145
Chapter 21 DoS Defend Commands
DoS (Denial of Service) Attack is to occupy the network bandwidth maliciously by the network attackers or the evil programs sending a lot of service requests to the Host. With the DoS Defend enabled, the switch can analyze the specific field of the received packets and provide the defend measures to ensure the normal working of the local network.
21.1 ip dos-prevent Description
The ip dos-prevent command is used to enable the DoS defend function globally. To disable the DoS defend function, please use no ip dos-prevent command.
Syntax
ip dos-prevent
no ip dos-prevent
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the DoS defend function globally:
T2600G-28TS(config)#ip dos-prevent
21.2 ip dos-prevent type Description
The ip dos-prevent type command is used to select the DoS Defend Type. To disable the corresponding Defend Type, please use no ip dos-prevent type command.
146
Syntax
ip dos-prevent type { land | scan-synfin | xma-scan | null-scan | port-less-1024 | blat | ping-flood | syn-flood | win-nuke }
no ip dos-prevent type { land | scan-synfin | xma-scan | null-scan | port-less-1024 | blat | ping-flood | syn-flood | win-nuke }
Parameter
land —— Land attack.
scan-synfin —— Scan SYNFIN attack.
xma-scan —— Xma Scan attack.
null-scan —— NULL Scan attack.
port-less-1024 ——The SYN packets whose Source Port less than 1024.
blat —— Blat attack.
ping-flood —— Ping flooding attack. With the ping flood attack enabled, the switch will limit automatically the forwarding speed of ping packets to 512K when attacked by ping flood.
syn-flood —— SYN/SYN-ACK flooding attack. With the syn-flood attack enabled, the switch will limit automatically the forwarding speed of ping packets to 512K when attacked by syn-flood.
win-nuke —— winNuke attack.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the DoS Defend Type named Land attack:
T2600G-28TS(config)#ip dos-prevent type land
147
21.3 show ip dos-prevent Description
The show ip dos-prevent command is used to display the DoS information of the detected DoS attack, including enable/disable status, the DoS Defend Type, the count of the attack, etc.
Syntax
show ip dos-prevent
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the DoS information of the detected DoS attack globally:
T2600G-28TS(config)#show ip dos-prevent
148
Chapter 22 IEEE 802.1X Commands
IEEE 802.1X function is to provide an access control for LAN ports via the authentication. An 802.1X system include three entities: supplicant, authenticator and authentication server. Supplicant: the device that requests access to the LAN. Authentication server: performs the actual authentication of the supplicant. It validates the
identity of the supplicant and notifies the authenticator whether or not the supplicant is authorized to access the LAN.
Authenticator: controls the physical access to the network based on the authentication status of the supplicant. It is usually an 802.1X-supported network device, such as this TP-Link switch. It acts as an intermediary (proxy) between the supplicant and the authentication server, requesting identity information from the supplicant, verifying that information with the authentication server, and relaying a response to the supplicant.
This chapter handles with the authentication process between the supplicant and the switch. To realize the authentication and accounting function, you should also enbable the AAA function and configure the RADIUS server. Go to Chapter 44 AAA Commands for more details.
22.1 dot1x system-auth-control Description
The dot1x system-auth-control command is used to enable the IEEE 802.1X function globally. To disable the IEEE 802.1X function, please use no dot1x system-auth-control command.
Syntax
dot1x system-auth-control
no dot1x system-auth-control
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the IEEE 802.1X function:
T2600G-28TS(config)#dot1x system-auth-control
149
22.2 dot1x handshake Description
The dot1x handshake command is used enable the handshake feature. The handshake feature is used to detect the connection status between the TP-Link 802.1x supplicant and the switch. Please disable the handshake feature if you are using a non-TP-Link 802.1x-compliant client software. This feature is enabled by default.
Syntax
dot1x handshake
no dot1x handshake
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Disable the 802.1X handshake function:
T2600G-28TS(config)# no dot1x handshake
22.3 dot1x auth-method Description
The dot1x auth-method command is used to configure the Authentication Method of IEEE 802.1X and the default 802.1x authentication method is “eap”. To restore to the default 802.1x authentication method, please use no dot1x auth-method command.
Syntax
dot1x auth-method { pap | eap }
no dot1x auth-method
Parameter
pap | eap ——Authentication Methods.
150
pap: EAP termination mode. IEEE 802.1X authentication system uses extensible authentication protocol (EAP) to exchange information between the switch and the client. The EAP packets are terminated at the switch and repackaged in the Password Authentication Protocol (PAP) packets, and then transferred to the RADIUS server.
eap: EAP relay mode. IEEE 802.1X authentication system uses extensible authentication protocol (EAP) to exchange information between the switch and the client. The EAP protocol packets with authentication data are encapsulated in the advanced protocol (such as RADIUS) packets and transmitted to the authentication server.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the Authentication Method of IEEE 802.1X as “pap”:
T2600G-28TS(config)#dot1x auth-method pap
22.4 dot1x accounting Description
The dot1x accounting command is used to enable the IEEE 802.1X accounting function globally. To disable the IEEE 802.1X accounting function, please use no dot1x accounting command.
Syntax
dot1x accounting
no dot1x accounting
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
151
Example
Enable the enable the IEEE 802.1X accounting function globally:
T2600G-28TS(config)#dot1x accounting
22.5 dot1x vlan-assignment Description
The dot1x vlan-assignment command is used to enable the 802.1X VLAN assignment feature. 802.1x VLAN assignment is a technology allowing the RADIUS server to send the VLAN assignment to the port when the port is authenticated. If the assigned VLAN does not exist on the switch, the switch will create the related VLAN automatically, add the authenticated port to the VLAN and change the PVID based on the assigned VLAN. If the assigned VLAN exists on the switch, the switch will directly add the authenticated port to the related VLAN and change the PVID instead of creating a new VLAN. If no VLAN is supplied by the RADIUS server or if 802.1x authentication is disabled, the port will be in its original VLAN after successful authentication. To disable the 802.1X VLAN assignment feature, please use no dot1x vlan-assignment command.
Syntax
dot1x vlan-assignment
no dot1x vlan-assignment
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the 802.1X VLAN assignment feature globally:
T2600G-28TS(config)# dot1x vlan-assignment
152
22.6 dot1x guest-vlan(global) Description
The dot1x guest-vlan command is used to enable the Guest VLAN function globally. To disable the Guest VLAN function, please use no dot1x guest-vlan command.
Syntax
dot1x guest-vlan vid
no dot1x guest-vlan
Parameter
vid —— The VLAN ID needed to enable the Guest VLAN function, ranging from 2 to 4094. The supplicants in the Guest VLAN can access the specified network source.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the Guest VLAN function for VLAN 5:
T2600G-28TS(config)#dot1x guest-vlan 5
22.7 dot1x quiet-period Description
The dot1x quiet-period command is used to enable the quiet-period function. To disable the function, please use no dot1x quiet-period command.
Syntax
dot1x quiet-period [ time ]
no dot1x quiet-period
153
Parameter
time —— The length of the quiet-period time. If one user’s authentication fails, its subsequent IEEE 802.1x authentication requests will not be processed during the quiet-period time. It ranges from 1 to 999 seconds and the default value is 10 seconds.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the quiet-period function:
T2600G-28TS(config)#dot1x quiet-period
Enable the quiet-period function and set the quiet-period as 5 seconds:
T2600G-28TS(config)#dot1x quiet-period 5
22.8 dot1x timeout supplicant-timeout Description
The dot1x timeout supplicant-timeout command is used to configure the supplicant timeout. To restore to the default, please use no dot1x timeout supplicant-timeout command.
Syntax
dot1x timeout supplicant-timeout time
no dot1x timeout supplicant-timeout
Parameter
time ——The maximum time for the switch to wait for the response from supplicant before resending a request to the supplicant., ranging from 1 to 9 in second. By default, it is 3 seconds.
Command Mode
Global Configuration Mode
154
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the supplicant timeout value as 5 seconds:
T2600G-28TS(config)#dot1x timeout supplicant-timeout 5
22.9 dot1x max-reauth-req Description
The dot1x max-reauth-req command is used to configure the maximum transfer times of the repeated authentication request when the server cannot be connected. To restore to the default value, please use no dot1x max-reauth-req command.
Syntax
dot1x max-reauth-req times
no dot1x max-reauth-req
Parameter
times —— The maximum transfer times of the repeated authentication request, ranging from 1 to 9 in times. By default, the value is 3.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the maximum transfer times of the repeated authentication request as 5:
T2600G-28TS(config)#dot1x max-reauth-req 5
155
22.10 dot1x Description
The dot1x command is used to enable the IEEE 802.1X function for a specified port. To disable the IEEE 802.1X function for a specified port, please use no dot1x command.
Syntax
dot1x
no dot1x
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet )
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the IEEE 802.1X function for the Gigabit Ethernet port 1:
T2600G-28TS(config)#interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)#dot1x
22.11 dot1x guest-vlan(interface) Description
The dot1x guest-vlan command is used to enable the guest VLAN function for a specified port. To disable the Guest VLAN function for a specified port, please use no dot1x guest-vlan command. Please ensure that the Control Type of the corresponding port is port-based before enabling the guest VLAN function for it.
Syntax
dot1x guest-vlan
no dot1x guest-vlan
156
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the Guest VLAN function for Gigabit Ethernet port 1/0/2:
T2600G-28TS(config)#interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)#dot1x guest-vlan
22.12 dot1x mab Description
The dot1x mab command is used to enable the MAB (MAC-Based Authentication Bypass) feature for the port. With MAB feature enabled, the switch automatically sends the authentication server a RADIUS access request frame with the client’s MAC address as the username and password. It is also necessary to configure the RADIUS server with the client’s information for authentication. You can enable this feature on IEEE 802.1x ports connected to devices without 802.1X capability. For example, most printers, IP phones and fax machines do not have 802.1X capability. To disable the MAB feature for the port, please use no dot1x mab command.
Syntax
dot1x mab
no dot1x mab
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the MAB feature for Gigabit Ethernet port 20:
157
T2600G-28TS(config)#interface gigabitEthernet 1/0/20
T2600G-28TS(config-if)#dot1x mab
22.13 dot1x port-control Description
The dot1x port-control command is used to configure the Control Mode of IEEE 802.1X for the specified port. By default, the control mode is “auto”. To restore to the default configuration, please use no dot1x port-control command.
Syntax
dot1x port-control {auto | authorized-force | unauthorized-force}
no dot1x port-control
Parameter
auto | authorized-force | unauthorized-force —— The Control Mode for the port.
auto: In this mode, the port will normally work only after passing the 802.1X Authentication.
authorized-force: In this mode, the port can work normally without passing the 802.1X Authentication.
unauthorized-force: In this mode, the port is forbidden working for its fixed unauthorized status.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the Control Mode for Gigabit Ethernet port 20 as “authorized-force”:
T2600G-28TS(config)#interface gigabitEthernet 1/0/20
T2600G-28TS(config-if)#dot1x port-control authorized-force
158
22.14 dot1x port-method Description
The dot1x port-method command is used to configure the control type of IEEE 802.1X for the specified port. By default, the control type is “mac-based”. To restore to the default configuration, please use no dot1x port-method command.
Syntax
dot1x port-method { mac-based | port-based }
no dot1x port-method
Parameter
mac-based | port-based ——The control type for the port.
mac-based: Any client connected to the port should pass the 802.1X authentication for access.
port-based: All the clients connected to the port can access the network on the condition that any one of the clients has passed the 802.1X Authentication.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the Control Type for Gigabit Ethernet port 20 as “port-based”:
T2600G-28TS(config)#interface gigabitEthernet 1/0/20
T2600G-28TS(config-if)#dot1x port-method port-based
22.15 show dot1x global Description
The show dot1x global command is used to display the global configuration of 801.X.
159
Syntax
show dot1x global
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configuration of 801.X globally:
T2600G-28TS(config)#show dot1x global
22.16 show dot1x interface Description
The show dot1x interface command is used to display all ports or the specified port’s configuration information of 801.X.
Syntax
show dot1x interface [ gigabitEthernet port ]
Parameter port —— The Ethernet port number. If not specified, the information of all the ports will be displayed.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configuration information of 801.X for Gigabit Ethernet port 20:
T2600G-28TS(config)#show dot1x interface gigabitEthernet 1/0/20
Display the configuration information of 801.X for all Ethernet ports:
T2600G-28TS(config)#show dot1x interface
160
Chapter 23 PPPoE ID-Insertion Commands
The PPPoE ID-Insertion feature provides a way to extract a Vendor-specific tag as an identifier for the authentication, authorization, and accounting (AAA) access requests on an Ethernet interface. When enabled, the switch attaches a tag to the PPPoE discovery packets, which is called the PPPoE Vendor-Specific tag and it contains a unique line identifier. There are two formats of Vendor-specific tags: Circuit-ID format and Remote-ID format. The BRAS receives the tagged packet, decodes the tag, and uses the Circuit-ID/Remote-ID field of that tag as a NAS-Port-ID attribute in the RADIUS server for PPP authentication and AAA (authentication, authorization, and accounting) access requests. The switch will remove the Circuit-ID/Remote-ID tag from the received PPPoE Active Discovery Offer and Session-confirmation packets from the BRAS.
23.1 pppoe id-insertion(global) Description
The pppoe id-insertion command is used to enable the PPPoE ID-Insertion function globally. To disable the PPPoE ID-Insertion function, please use no pppoe id-insertion command.
Syntax
pppoe id-insertion
no pppoe id-insertion
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the PPPoE ID-Insertion function:
T2600G-28TS(config)# pppoe id-insertion
161
23.2 pppoe circuit-id(interface) Description
The pppoe circuit-id command is used to enable the PPPoE Circuit-ID Insertion function for a specified port. To disable the PPPoE Circuit-ID Insertion function on a specified port, please use no pppoe circuit-id command.
Syntax
pppoe circuit-id
no pppoe circuit-id
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the PPPoE Circuit-ID Insertion function for the Gigabit Ethernet port 1/0/1:
T2600G-28TS (config)# interface gigabitEthernet 1/0/1
T2600G-28TS (config-if)# pppoe circuit-id
23.3 pppoe circuit-id type Description
The pppoe circuit-id type command is used to configure the type of PPPoE Circuit-ID for a specified port. By default, the PPPoE Circuit-ID type is “ip”.
Syntax
pppoe circuit-id type { mac | ip | udf [Value] | udf-only [Value] }
Parameter
mac | ip | udf | udf-only —— The type of PPPoE Circuit-ID for the port.
mac: The MAC address of the switch will be used to encode the Circuit-ID option.
162
ip: The IP address of the switch will be used to encode the Circuit-ID option. This is the default value.
udf: A user specified string with the maximum length of 40 characters will be used to encode the Circuit-ID option.
udf-only: Only the user specified string with the maximum length of 40 will be used to encode the Circuit-ID option.
Value —— The value of udf/udf-only. The maximum length is 40 characters.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the type of PPPoE Circuit-ID as “mac” for the Gigabit Ethernet port 1/0/1:
T2600G-28TS (config)# interface gigabitEthernet 1/0/1
T2600G-28TS (config-if)# pppoe circuit-id type mac
23.4 pppoe remote-id Description
The pppoe remote-id command is used to enable the PPPoE Remote-ID Insertion and configure the Remote-ID value for a specified port. To disable the PPPoE Remote-ID Insertion function on a specified port, please use no pppoe remote-id command. By default, the PPPoE Remote-ID Insertion is disabled.
Syntax
pppoe remote-id [Value]
no pppoe remote-id
Parameter
Value —— The value of UDF. The maximum length is 40 characters. If not specified, the default value will be the PPPoE client’s MAC address.
163
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the remote-ID as “mac” for the Gigabit Ethernet port 1/0/1:
T2600G-28TS (config)# interface gigabitEthernet 1/0/1
T2600G-28TS (config-if)# pppoe remote-id mac
23.5 show pppoe id-insertion global Description
The show pppoe id-insertion global command is used to display the global configuration of PPPoE Circuit-ID Insertion function.
Syntax
show pppoe id-insertion global
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configuration of PPPoE Circuit-ID Insertion function globally:
T2600G-28TS # show pppoe circuit-id global
23.6 show pppoe id-insertion interface Description
The show pppoe id-insertion interface command is used to display all ports’ or the specified port’s configuration information of PPPoE Circuit-ID Insertion function.
164
Syntax
show pppoe id-insertion interface [gigabitEthernet port ]
Parameter
port —— The Fast/Gigabit Ethernet port number.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configuration information of PPPoE Circuit-ID Insertion function of all Ethernet ports:
T2600G-28TS# show pppoe id-insertion interface
Display the configuration of PPPoE Circuit-ID Insertion function of the Gigabit Ethernet port 1/0/1 :
T2600G-28TS# show pppoe id-insertion interface gigabitEthernet 1/0/1
165
Chapter 24 System Log Commands
The log information will record the settings and operation of the switch respectively for you to monitor operation status and diagnose malfunction.
24.1 logging buffer Description
The logging buffer command is used to store the system log messages to an internal buffer. To disable the log buffer function, please use the no logging buffer command. Local Log is the system log information saved in the switch. It has two output channels, that is, it can be saved to two different positions, log buffer and log flash memory. The log buffer indicates the RAM for saving system log and the information in the log buffer can be got by show logging buffer command. It will be lost when the switch is restarted.
Syntax
logging buffer
no logging buffer
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Enable the system log buffer:
T2600G-28TS(config)#logging buffer
24.2 logging buffer level Description
The logging buffer level command is used to configure the severity level and the status of the configuration input to the log buffer. To return to the default configuration, please use no logging buffer level command.
166
Syntax
logging buffer level level
no logging buffer level
Parameter
level —— Severity level of the log information output to each channel. There are 8 severity levels marked with values 0-7. The smaller value has the higher priority. Only the log with the same or smaller severity level value will be output. By default, it is 6 indicating that the log information with level 0-6 will be saved in the log buffer.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Set the severity level as 5:
T2600G-28TS(config)#logging buffer level 5
24.3 logging file flash Description
The logging file flash command is used to store the log messages in a file in the flash on the switch. To disable the log file flash function, please use no logging file flash command. This function is disabled by default. The log file flash indicates the flash sector for saving system log. The information in the log file of the flash will not be lost after the switch is restarted and can be got by the show logging flash command.
Syntax
logging file flash
no logging file flash
Command Mode
Global Configuration Mode
167
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Enable the log file flash function:
T2600G-28TS(config)#logging file flash
24.4 logging file flash frequency Description
The logging file flash frequency command is used to specify the frequency to synchronize the system log file in the log buffer to the flash. To resume the default synchronizing frequency, please use the no logging file flash frequency command.
Syntax
logging file flash frequency { periodic periodic | immediate }
no logging file flash frequency
Parameter
periodic —— The frequency to synchronize the system log file in the log buffer to the flash, ranging from 1 to 48 hours. By default, the synchronization process takes place every 24 hours.
immediate —— The system log file in the buffer will be synchronized to the flash immediately. This option will reduce the life of the flash and is not recommended.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Specify the log file synchronization frequency as 10 hours:
T2600G-28TS(config)#logging file flash frequency periodic10
168
24.5 logging file flash level Description
The logging file flash level command is used to specify the system log message severity level. Messages will a severity level equal to or higher than this value will be stored to the flash. To restore to the default level, please use no logging file flash level command.
Syntax
logging file flash level level
no logging file flash level
Parameter
level —— Severity level of the log message. There are 8 severity levels marked with values 0-7. The smaller value has the higher priority. Only the log with the same or smaller severity level value will be saved to the flash. By default, it is 3 indicating that the log message marked with 0~3 will be saved in the log flash.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Save the log messages with their severities equal or higher than 7 to the flash :
T2600G-28TS(config)#logging file flash level 7
24.6 logging host index Description
The logging host index command is used to configure the Log Host. To clear the configuration of the specified Log Host, please use no logging host index command. Log Host is to receive the system log from other devices. You can remotely monitor the settings and operation status of other devices through the log host.
169
Syntax
logging host index idx host-ip level
no logging host index idx
Parameter
idx —— The index of the log host. The switch supports 4 log hosts at most.
host-ip —— The IP for the log host.
level —— The severity level of the log information sent to each log host. There are 8 severity levels marked with values 0-7. The smaller value has the higher priority. Only the log with the same or smaller severity level value will be sent to the corresponding log host. By default, it is 6 indicating that the log information marked with 0~6 will be sent to the log host.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Enable log host 2 and set its IP address as 192.168.0.148, the level 5:
T2600G-28TS(config)# logging host index 2 192.168.0.148 5
24.7 logging console Description
The logging console command is used to send the system logs to the console port. To disable logging to the console, please use no logging console command. This function is enabled by default.
Syntax
logging console
no logging console
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
170
Example
Enable logging to the console port:
T2600G-28TS(config)# logging console
24.8 logging console level Description
The logging console level command is used to limit messages logged to the console port. System logs no higher than the set threshold level will be displayed on the console port. To restore the threshold level to default value, please use no logging console level command.
Syntax
logging console level level
no logging monitor level
Parameter
level —— Severity level of the log information output to the console port. There are 8 severity levels marked with values 0-7. The smaller value has the higher priority. Only the log with the same or smaller severity level value will be output to the terminal devices. By default, it is 5 indicating that all the log information between level 0-5 will be output to the terminal devices.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Output the log information with severity levels between 0-7 to the console port:
T2600G-28TS(config)# logging console level 7
171
24.9 logging monitor Description
The logging monitor command is used to display the system logs on the terminal devices. To disable logging to the terminal, please use no logging monitor command. This function is enabled by default.
Syntax
logging monitor
no logging monitor
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Disable logging to the terminal devices:
T2600G-28TS(config)# no logging monitor
24.10 logging monitor level Description
The logging monitor level command is used to limit messages logged to the terminal devices. System logs no higher than the set threshold level will be displayed on the terminal devices. To restore the threshold level to default value, please use no logging monitor level command.
Syntax
logging monitor level level
no logging monitor level
Parameter
level —— Severity level of the log information output to the terminal devices. There are 8 severity levels marked with values 0-7. The smaller value has the higher priority. Only the log with the same or smaller severity level value will
172
be output to the terminal devices. By default, it is 5 indicating that all the log information between level 0-5 will be output to the terminal devices.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Output the log information with severity levels between 0-7 to the terminal devices:
T2600G-28TS(config)# logging monitor level 7
24.11 clear logging Description
The clear logging command is used to clear the information in the log buffer and log file.
Syntax
clear logging [ buffer | flash ]
Parameter
buffer | flash —The output channels: buffer and flash. Clear the information of the two channels, by default.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Clear the information in the log file:
T2600G-28TS(config)# clear logging buffer
173
24.12 show logging local-config Description
The show logging local-config command is used to display the configuration of the Local Log output to the console, the terminal, the log buffer and the log file.
Syntax
show logging local-config
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configuration of the Local Log:
T2600G-28TS(config)# show logging local-config
24.13 show logging loghost Description
The show logging loghost command is used to display the configuration of the log host.
Syntax
show logging loghost [ index ]
Parameter
index ——The index of the log host whose configuration will be displayed, ranging from 1 to 4. Display the configuration of all the log hosts by default.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
174
Example
Display the configuration of the log host 2:
T2600G-28TS(config)# show logging loghost 2
24.14 show logging buffer Description
The show logging buffer command is used to display the log information in the log buffer according to the severity level.
Syntax
show logging buffer [ level level ]
Parameter
level —— Severity level. There are 8 severity levels marked with values 0-7. The information of levels with priority not lower than the select level will display. Display all the log information in the log buffer by default.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the log information from level 0 to level 5 in the log buffer:
T2600G-28TS(config)# show logging buffer level 5
24.15 show logging flash Description
The show logging flash command is used to display the log information in the log file according to the severity level.
Syntax
show logging flash [ level level ]
175
Parameter
level —— Severity level. There are 8 severity levels marked with values 0-7. The information of levels with priority not lower than the select level will display. Display all the log information in the log file by default.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the log information with the level marked 0~3 in the log file:
T2600G-28TS(config)# show logging flash level 3
176
Chapter 25 SSH Commands
SSH (Security Shell) can provide the unsecured remote management with security and powerful authentication to ensure the security of the management information.
25.1 ip ssh server Description
The ip ssh server command is used to enable SSH function. To disable the SSH function, please use no ip ssh server command.
Syntax
ip ssh server
no ip ssh server
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the SSH function:
T2600G-28TS(config)# ip ssh server
25.2 ip ssh version Description
The ip ssh version command is used to enable the SSH protocol version. To disable the protocol version, please use no ip ssh version command.
Syntax
ip ssh version { v1 | v2 }
no ip ssh version { v1 | v2 }
177
Parameter
v1 | v2 —— The SSH protocol version to be enabled. They represent SSH v1 and SSH v2 respectively.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable SSH v2:
T2600G-28TS(config)# ip ssh version v2
25.3 ip ssh algorithm Description
The ip ssh algorithm command is used to configure the algorithm in SSH function. To disable the specified algorithm, please use no ip ssh algorithm command.
Syntax ip ssh algorithm { AES128-CBC | AES192-CBC | AES256-CBC | Blowfish-CBC | Cast128-CBC | 3DES-CBC | HMAC-SHA1 | HMAC-MD5 }
no ip ssh algorithm
Parameter AES128-CBC | AES192-CBC | AES256-CBC | Blowfish-CBC | Cast128-CBC | 3DES-CBC | HMAC-SHA1 | HMAC-MD5 —— Specify the SSH algorithm.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Specify the SSH algorithm as AES128-CBC:
T2600G-28TS(config)# ip ssh algorithm AES128-CBC
178
25.4 ip ssh timeout Description
The ip ssh timeout command is used to specify the idle-timeout time of SSH. To restore to the factory defaults, please use ip ssh timeout command.
Syntax
ip ssh timeout value
no ip ssh timeout
Parameter
value —— The Idle-timeout time. During this period, the system will automatically release the connection if there is no operation from the client. It ranges from 1 to 120 in seconds. By default, this value is 120 seconds.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the idle-timeout time of SSH as 30 seconds:
T2600G-28TS(config)# ip ssh timeout 30
25.5 ip ssh max-client Description
The ip ssh max-client command is used to specify the maximum number of the connections to the SSH server. To return to the default configuration, please use no ip ssh max-client command.
Syntax
ip ssh max-client num
no ip ssh max-client
179
Parameter
num —— The maximum number of the connections to the SSH server. It ranges from 1 to 5. By default, this value is 5.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the maximum number of the connections to the SSH server as 3:
T2600G-28TS(config)# ip ssh max-client 3
25.6 ip ssh download Description
The ip ssh download command is used to download the SSH key file from TFTP server.
Syntax ip ssh download { v1 | v2 } key-file ip-address ip-addr
Parameter v1 | v2 —— Select the type of SSH key to download, v1 represents SSH-1, v2 represents SSH-2.
key-file —— The name of the key-file which is selected to download. The length of the name ranges from 1 to 25 characters. The key length of the downloaded file must be in the range of 512 to 3072 bits.
ip-addr —— The IP address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
180
Example Download an SSH-1 type key file named ssh-key from TFTP server with the IP address 192.168.0.148:
T2600G-28TS(config)# ip ssh download v1 ssh-key ip-address
192.168.0.148
Download an SSH-1 type key file named ssh-key from TFTP server with the IP address fe80::1234:
T2600G-28TS(config)# ip ssh download v1 ssh-key ip-address fe80::1234
25.7 remove public-key Description
The remove public-key command is used to remove the SSH public key from the switch.
Syntax remove public-key { v1 | v2 }
Parameter v1 | v2 —— Select the type of SSH public key, v1 represents SSH-1, v2 represents SSH-2.
Command Mode Privileged EXEC Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Remove the SSH-1 type public key from the switch:
T2600G-28TS# remove public-key v1
25.8 show ip ssh Description
The show ip ssh command is used to display the global configuration of SSH.
Syntax show ip ssh
181
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the global configuration of SSH:
T2600G-28TS(config)# show ip ssh
182
Chapter 26 MAC Address Commands
MAC Address configuration can improve the network security by configuring the Port Security and maintaining the address information by managing the Address Table.
26.1 mac address-table static Description
The mac address-table static command is used to add the static MAC address entry. To remove the corresponding entry, please use no mac address-table static command. The static address can be added or removed manually, independent of the aging time. In the stable networks, the static MAC address entries can facilitate the switch to reduce broadcast packets and enhance the efficiency of packets forwarding remarkably.
Syntax mac address-table static mac-addr vid vid interface gigabitEthernet port
no mac address-table static { mac-addr | vid vid | mac-addr vid vid | interface gigabitEthernet port }
Parameter mac-addr ——The MAC address of the entry you desire to add.
vid —— The VLAN ID number of your desired entry. It ranges from 1 to 4094.
port —— The Ethernet port number of your desired entry.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Add a static Mac address entry to bind the MAC address 00:02:58:4f:6c:23, VLAN1 and port 1 together:
T2600G-28TS(config)# mac address-table static 00:02:58:4f:6c:23 vid 1
interface gigabitEthernet 1/0/1
183
26.2 mac address-table aging-time Description
The mac address-table aging-time command is used to configure aging time for the dynamic address. To return to the default configuration, please use no mac address-table aging-time command.
Syntax mac address-table aging-time aging-time
no mac address-table aging-time
Parameter aging-time —— The aging time for the dynamic address. The value of it can be 0 or ranges from 10 to 630 seconds. When 0 is entered, the Auto Aging function is disabled. It is 300 by default.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the aging time as 500 seconds:
T2600G-28TS(config)# mac address-table aging-time 500
26.3 mac address-table filtering Description
The mac address-table filtering command is used to add the filtering address entry. To delete the corresponding entry, please use no mac address-table filtering command. The filtering address function is to forbid the undesired package to be forwarded. The filtering address can be added or removed manually, independent of the aging time.
Syntax mac address-table filtering mac-addr vid vid
no mac address-table filtering {[ mac-addr ] [ vid vid ]}
Parameter mac-addr —— The MAC address to be filtered.
184
vid —— The corresponding VLAN ID of the MAC address. It ranges from 1 to 4094.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Add a filtering address entry of which VLAN ID is 1 and MAC address is 00:1e:4b:04:01:5d:
T2600G-28TS(config)# mac address-table filtering 00:1e:4b:04:01:5d vid 1
26.4 mac address-table notification Description
The mac address-table notification command is used to configure global settings of MAC address table notification.
Syntax mac address-table notification { [ global-status enable | disable ] [ table-full-status enable | disable ] [ interval time ] }
Parameter global-status enable | disable —— Enable/Disable the notification function globally.
table-full-status enable | disable —— Enable/Disable the MAC threshold notification. With this feature enabled, a SNMP notification is generated and sent to the network management system (NMS) when the threshold of the switch’s MAC address table is reached or exceeded.
interval time —— Specify the notification trap interval between each set of traps that are generated to the NMS. The interval ranges from 1 to 1000 seconds and it’s 1 second by default.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
185
Example Enable the global MAC address notification and table full notification, specify the notification sending interval as 2 seconds:
T2600G-28TS(config)# mac address-table notification global-status
enable table-full-status enable interval 2
26.5 mac address-table max-mac-count Description
The mac address-table max-mac-count command is used to configure the Port Security. To return to the default configurations, please use no mac address-table max-mac-count command. Port Security is to protect the switch from the malicious MAC address attack by limiting the maximum number of the MAC addresses that can be learned on the port. The port with Port Security feature enabled will learned the MAC address dynamically. When the learned MAC address number reaches the maximum, the port will stop learning. Therefore, the other devices with the MAC address unlearned can not access to the network via this port.
Syntax mac address-table max-mac-count { [ max-number num ] [ mode { dynamic | static | permanent } ] [ status { forward | drop | disable } ] }
no mac address-table max-mac-count [ max-number | mode | status ]
Parameter num —— The maximum number of MAC addresses that can be learned on the port. It ranges from 0 to 64. By default this value is 64.
dynamic | static | permanent —— Learn mode for MAC addresses. There are three modes, including Dynamic mode, Static mode and Permanent mode. When Dynamic mode is selected, the learned MAC address will be deleted automatically after the aging time. When Static mode is selected, the learned MAC address will be out of the influence of the aging time and can only be deleted manually. The learned entries will be cleared after the switch is rebooted. When permanent mode is selected, the learned MAC address will be out of the influence of the aging time and can only be deleted manually too. However, the learned entries will be saved even the switch is rebooted.
status —— Select the action to be taken when the number of the MAC addresses reaches the maximum learning number on the port. By default this function is disabled.
186
• forward: The packets will be forward but not be learned when learned MAC number exceeds the the maximum MAC address number on this port.
• drop: The packets will be dropped when learned MAC number exceeds the the maximum MAC address number on this port.
• disable: The MAC address threshold on this port is disabled.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable Port Security function for port 1/0/1, select Static mode as the learn mode, and specify the maximum number of MAC addresses that can be learned on this port as 30. When the number of MAC address entries reaches 30 on this port, new entry will be dropped :
T2600G-28TS(config)# interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)# mac address-table max-mac-count max-number
30 mode static status drop
26.6 mac address-table notification (interface) Description
The mac address-table notification command is used to configure the MAC change notification on port.
Syntax mac address-table notification { [ learn-mode-change enable | disable ] [ exceed-max-learned enable | disable ] [ new-mac-learned enable | disable ] }
Parameter learn-mode-change enable | disable —— Enable/Disable the learn-mode-change notification. With this feature enabled, a SNMP notification is generated and sent to the network management system (NMS) when the learning mode of this port changes. To configure the learning mode configuration, please refer to mac address-table max-mac-count.
187
exceed-max-learned enable | disable —— Enable/Disable the MAC address threshold notification on this port. With this feature enabled, a SNMP notification is generated and sent to the network management system (NMS) when the MAC address threshold limit on this port is reached or exceeded. To configure the port’s MAC address threshold, please refer to mac address-table max-mac-count.
new-mac-learned enable | disable —— Enable/Disable the new-mac-learned notification on this port. With this feature enabled, a SNMP notification is generated and sent to the network management system (NMS) when the port learns a new MAC address.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the learn-mode-change notification on port 1/0/2:
T2600G-28TS(config)# mac address-table notification global-status
enable
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# mac address-table notification
learn-mode-change enable
26.7 mac address-table security Description
The mac address-table security command is used to configure security of the MAC address table in a specified VLAN.
Syntax mac address-table security vid vid max-learn number { forward | drop | disable }
Parameter vid —— Speicify the VLAN ID to configure its MAC address table.
188
number —— Configure the threshold of the MAC address table in this VLAN. It ranges from 0 to 16383.
forward | drop | disable —— Choose the mode when learned MAC number exceeds the threshold of the MAC address table in this VLAN.
• Drop: The packets will be dropped when learned MAC number exceeds the threshold of the MAC address table in this VLAN..
• Forward: The packets will be forward but not be learned when learned MAC number exceeds the threshold of the MAC address table in this VLAN..
• Disable: The threshold of the MAC address table is disabled.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the max learned MAC address number is VLAN 2 as 1000, and drop the packets that have no match in the MAC address table:
T2600G-28TS(config)# mac address-table security vid 2 max-learn 1000
drop
26.8 show mac address-table Description
The show mac address-table command is used to display the information of all address entries.
Syntax show mac address-table { dynamic | static | filtering }
Parameter dynamic | static | filtering —— The type of your desired entry. By default all the entries are displayed.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
189
Example Display the information of all address entries:
T2600G-28TS(config)# show mac address-table
26.9 clear mac address-table Description
The show mac address-table command is used to clear the specified address entries.
Syntax clear mac address-table { dynamic | static | filtering }
Parameter dynamic | static | filtering —— The type of your desired entry.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Clear the information of all static address entries:
T2600G-28TS(config)# clear mac address-table static
26.10 show mac address-table aging-time Description
The show mac address-table aging-time command is used to display the Aging Time of the MAC address.
Syntax show mac address-table aging-time
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
190
Example Display the Aging Time of the MAC address:
T2600G-28TS(config)# show mac address-table aging-time
26.11 show mac address-table max-mac-count Description
The show mac address-table max-mac-count interface gigabitEthernet command is used to display the security configuration of all ports or the specified port.
Syntax show mac address-table max-mac-count { all | interface gigabitEthernet port }
Parameter
all —— Displays the security information of all the Ethernet ports.
port —— The Ethernet port number.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the security configuration of all ports:
T2600G-28TS(config)# show mac address-table max-mac-count all
Display the security configuration of port 1/0/1:
T2600G-28TS(config)# show mac address-table max-mac-count interface
gigabitEthernet 1/0/1
26.12 show mac address-table interface Description
The show mac address-table interface command is used to display the address configuration of the specified port/port channel.
191
Syntax show mac address-table interface { gigabitEthernet port | port-channel port-channel-id }
Parameter
port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the address configuration of port 1/0/1:
T2600G-28TS(config)# show mac address-table interface gigabitEthernet
1/0/1
26.13 show mac address-table count Description
The show mac address-table count command is used to display the total amount of MAC address table.
Syntax show mac address-table count [ vlan vlan-id ]
Parameter
vlan-id —— Specify the VLAN which the MAC entries belong to.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the total MAC entry information in different VLANs:
T2600G-28TS(config)# show mac address-table count
192
26.14 show mac address-table address Description
The show mac address-table address command is used to display the information of the specified MAC address.
Syntax show mac address-table address mac-addr [ interface { gigabitEthernet port | port-channel port-channel-id } | vid vlan-id ]
Parameter
mac-addr ——The specified MAC address.
port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
vlan-id —— Specify the VLAN which the entry belongs to.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the information of the MAC address 00:00:00:00:23:00 in VLAN 1:
T2600G-28TS(config)#show mac address-table address 00:00:00:00:23:00
vid 1
26.15 show mac address-table vlan Description
The show mac address-table vlan command is used to display the MAC address configuration of the specified vlan.
Syntax show mac address-table vlan vid
Parameter
vid ——The specified VLAN id.
Command Mode Privileged EXEC Mode and Any Configuration Mode
193
Privilege Requirement
None.
Example Display the MAC address configuration of vlan 1:
T2600G-28TS(config)# show mac address-table vlan 1
26.16 show mac address-table notification Description
The show mac address-table notification command is used to display the MAC notificaiton configuration globally or on the specified port.
Syntax show mac address-table notification { all | interface gigabitEthernet port }
Parameter all —— Displays the notificaiton information globally and of all the Ethernet ports.
port —— Displays the notification information on the specified port.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the notificaiton configuration of all the ports:
T2600G-28TS(config)# show mac address-table notification all
26.17 show mac address-table security Description
The show mac address-table security command is used to display the MAC address security configuration globally or of the specified VLAN.
Syntax show mac address-table security [ vid vid ]
Parameter
vid ——The specified VLAN id.
194
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the MAC address security configuration of VLAN 1:
T2600G-28TS(config)# show mac address-table security vid 1
195
Chapter 27 System Configuration Commands
System Commands can be used to configure the System information and System IP, reboot and reset the switch, upgrade the switch system and other operations.
27.1 system-time manual Description
The system-time manual command is used to configure the system time manually.
Syntax system-time manual time
Parameter time —— Set the date and time manually, MM/DD/YYYY-HH:MM:SS. The valid value of the year ranges from 2000 to 2037.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Configure the system mode as manual, and the time is 12/20/2010 17:30:35
T2600G-28TS(config)# system-time manual 12/20/2010-17:30:35
27.2 system-time ntp Description
The system-time ntp command is used to configure the time zone and the IP address for the NTP Server. The switch will get UTC automatically if it has connected to an NTP Server.
Syntax system-time ntp { timezone } { ntp-server } { backup-ntp-server } { fetching-rate }
Parameter timezone —— Your local time-zone, and it ranges from UTC-12:00 to UTC+13:00.
196
The detailed information that each time-zone means are displayed as follow: UTC-12:00 —— TimeZone for International Date Line West. UTC-11:00 —— TimeZone for Coordinated Universal Time-11. UTC-10:00 —— TimeZone for Hawaii. UTC-09:00 —— TimeZone for Alaska. UTC-08:00 —— TimeZone for Pacific Time(US Canada). UTC-07:00 —— TimeZone for Mountain Time(US Canada). UTC-06:00 —— TimeZone for Central Time(US Canada). UTC-05:00 —— TimeZone for Eastern Time(US Canada). UTC-04:30 —— TimeZone for Caracas. UTC-04:00 —— TimeZone for Atlantic Time(Canada). UTC-03:30 —— TimeZone for Newfoundland. UTC-03:00 —— TimeZone for Buenos Aires, Salvador, Brasilia. UTC-02:00 —— TimeZone for Mid-Atlantic. UTC-01:00 —— TimeZone for Azores, Cape Verde Is. UTC —— TimeZone for Dublin, Edinburgh, Lisbon, London. UTC+01:00 —— TimeZone for Amsterdam, Berlin, Bern, Rome, Stockholm,
Vienna. UTC+02:00 —— TimeZone for Cairo, Athens, Bucharest, Amman, Beirut,
Jerusalem. UTC+03:00 —— TimeZone for Kuwait, Riyadh, Baghdad. UTC+03:30 —— TimeZone for Tehran. UTC+04:00 —— TimeZone for Moscow, St.Petersburg, Volgograd, Tbilisi,
Port Louis. UTC+04:30 —— TimeZone for Kabul. UTC+05:00 —— TimeZone for Islamabad, Karachi, Tashkent. UTC+05:30 —— TimeZone for Chennai, Kolkata, Mumbai, New Delhi. UTC+05:45 —— TimeZone for Kathmandu. UTC+06:00 —— TimeZone for Dhaka,Astana, Ekaterinburg. UTC+06:30 —— TimeZone for Yangon (Rangoon). UTC+07:00 —— TimeZone for Novosibrisk, Bangkok, Hanoi, Jakarta. UTC+08:00—— TimeZone for Beijing, Chongqing, Hong Kong, Urumqi,
Singapore. UTC+09:00 —— TimeZone for Seoul, Irkutsk, Osaka, Sapporo, Tokyo. UTC+09:30 —— TimeZone for Darwin, Adelaide. UTC+10:00 —— TimeZone for Canberra, Melbourne, Sydney, Brisbane. UTC+11:00 —— TimeZone for Solomon Is., New Caledonia, Vladivostok. UTC+12:00 —— TimeZone for Fiji, Magadan, Auckland, Welington. UTC+13:00 —— TimeZone for Nuku'alofa, Samoa.
ntp-server —— The IP address for the Primary NTP Server.
197
backup-ntp-server —— The IP address for the Secondary NTP Server. fetching-rate —— Specify the rate fetching time from NTP server.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure the system time mode as NTP, the time zone is UTC-12:00, the primary NTP server is 133.100.9.2 and the secondary NTP server is 139.78.100.163, the fetching-rate is 11 hours:
T2600G-28TS(config)# system-time ntp UTC-12:00 133.100.9.2
139.79.100.163 11
27.3 system-time dst predefined Description
The system-time dst predefined command is used to select a daylight saving time configuration from the predefined mode. The configuration can be used recurrently. To disable DST function, please use no system-time dst command.
Syntax system-time dst predefined [ USA | Australia | Europe | New-Zealand ]
no system-time dst
Parameter USA | Australia | Europe | New-Zealand —— The mode of daylight saving time. There are 4 options which are USA, Australia, Europe and New-Zealand respectively. The default value is Europe.
Following are the time ranges of each option:
USA: Second Sunday in March, 02:00 ~ First Sunday in November, 02:00. Australia: First Sunday in October, 02:00 ~ First Sunday in April, 03:00. Europe: Last Sunday in March, 01:00 ~ Last Sunday in October, 01:00. New Zealand: Last Sunday in September, 02:00 ~ First Sunday in April, 03:00.
Command Mode Global Configuration Mode
198
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Configure the daylight saving time as USA standard:
T2600G-28TS(config)#system-time dst predefined USA
27.4 system-time dst date Description
The system-time dst date command is used to configure the one-off daylight saving time. The start date is in the current year by default. The time range of the daylight saving time must shorter than one year, but you can configure it spanning years. To disable DST function, please use no system-time dst command.
Syntax system-time dst date {smonth} {sday} {stime} {syear} {emonth} {eday} {etime} {eyear}[offset]
no system-time dst
Parameter smonth ——The start month of the daylight saving time. There are 12 values showing as follows: Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec.
sday —— The start day of the daylight saving time, ranging from 1 to 31. Here you should show special attention to February and the differences between a solar month and a lunar month.
stime —— The start moment of the daylight saving time, HH:MM.
syear —— The start year of the daylight saving time.
emonth —— The end month of the daylight saving time. There are 12 values showing as follows: Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec.
eday —— The end day of the daylight saving time, ranging from q to 31. Here you should show special attention to February and the differences between a solar month and a lunar month.
etime —— The end moment of the daylight saving time, HH:MM.
eyear —— The end year of the daylight saving time.
offset —— The number of minutes to add during the daylight saving time. It is 60 minutes by default.
199
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Configure the daylight saving time from zero clock, Apr 1st to zero clock Oct 1st and the offset is 30 minutes in 2015:
T2600G-28TS(config)# system-time dst date Apr 1 00:00 2015 Oct 1 00:00
2015 30
27.5 system-time dst recurring Description
The system-time dst recurring command is used to configure the recurring daylight saving time. It can be configured spanning years. To disable DST function, please use no system-time dst command.
Syntax system-time dst recurring {sweek} {sday} {smonth} {stime} {eweek} {eday} {emonth} {etime} [offset]
no system-time dst
Parameter sweek——The start week of the daylight saving time. There are 5 values showing as follows: first, second, third, fourth, last.
sday —— The start day of the daylight saving time. There are 7 values showing as follows: Sun, Mon, Tue, Wed, Thu, Fri, Sat.
smonth —— The start month of the daylight saving time. There are 12 values showing as follows: Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec.
stime —— The start moment of the daylight saving time, HH:MM.
eweek ——The end week of the daylight saving time. There are 5 values showing as follows: first, second, third, fourth, last.
eday —— The end day of the daylight saving time. There are 5 values showing as follows: Sun, Mon, Tue, Wed, Thu, Fri, Sat.
emonth —— The end month of the daylight saving time. There are 12 values showing as following: Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec.
200
etime —— The end moment of the daylight saving time, HH:MM.
offset —— The number of minutes to add during the daylight saving time. It is 60 minutes by default.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure the daylight saving time from 2:00am, the first Sunday of May to 2:00am, the last Sunday of Oct and the offset is 45 minutes:
T2600G-28TS(config)# system-time dst recurring first Sun May 02:00 last
Sun Oct 02:00 45
27.6 hostname Description
The hostname command is used to configure the system name. To clear the system name information, please use no hostname command.
Syntax hostname [ hostname ]
no hostname
Parameter hostname —— System Name. The length of the name ranges from 1 to 32 characters. By default, it is the device name, for example “T2600G-28TS”.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Configure the system name as TPLINK:
T2600G-28TS(config)# hostname TPLINK
201
27.7 location Description
The location command is used to configure the system location. To clear the system location information, please use no location command.
Syntax location [ location ]
no location
Parameter
location —— Device Location. It consists of 32 characters at most. It is “SHENZHEN” by default.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Configure the system location as SHENZHEN:
T2600G-28TS(config)# location SHENSHEN
27.8 contact-info Description
The contact-info command is used to configure the system contact information. To clear the system contact information, please use no contact-info command.
Syntax contact-info [ contact_info ]
no contact-info
Parameter contact_info —— Contact Information. It consists of 32 characters at most. It is “www.tp-link.com” by default.
Command Mode Global Configuration Mode
202
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Configure the system contact information as www.tp-link.com:
T2600G-28TS(config)# contact-info www.tp-link.com
27.9 ip address Description
This ip address command is used to configure the IP address and IP subnet mask for the specified interface manually. The interface type includes: routed port, port-channel interface, loopback interface and VLAN interface.
Syntax
ip address { ip-addr } { mask } [ secondary ]
no ip address [ ip-addr ] [ mask ]
Parameter
ip-addr —— The IP address of the Layer 3 interface.
mask —— The subnet mask of the Layer 3 interface.
secondary —— Specify the interface’s secondary IP address. If this parameter is omitted here, the configured IP address is the interface’s primary address.
Command Mode
Interface Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create the VLAN interface 2 with the primary IP address as 192.168.1.1/24 and secondary IP address as 192.168.2.1/24:
T2600G-28TS(config)# interface vlan 2 T2600G-28TS(config-if)# ip address 192.168.1.1 255.255.255.0 T2600G-28TS(config-if)# ip address 192.168.2.1 255.255.255.0 secondary
203
27.10 ip address-alloc Description
The IP address-alloc command is used to enable the DHCP Client function or the BOOTP Protocol. When this function is enabled, the specified interface will obtain IP from DHCP Server or BOOTP server. To disable the IP obtaining function on the specified interface, please use the no ip address command. This command applies to the routed port, the port-channel interface and the VLAN interface.
Syntax
ip address-alloc { dhcp | bootp }
no ip address
Parameter
dhcp —— Specify the Layer 3 interface to obtain IP address from the DHCP Server.
bootp —— Specify the Layer 3 interface to obtain IP address from the BOOTP Server.
Command Mode
Interface Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the DHCP Client function on the Lay 3 routed port 1/0/1:
T2600G-28TS(config)# interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)# no switchport
T2600G-28TS(config-if)# ip address-alloc dhcp
Disable the IP address obtaining function on the VLAN interface 2:
T2600G-28TS(config)# interface vlan 2
T2600G-28TS(config-if)# no ip address
204
27.11 reset Description
The reset command is used to reset the switch’s software. After resetting, all configuration of the switch will restore to the factory defaults and your current settings will be lost.
Syntax reset
Command Mode Privileged EXEC Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Reset the software of the switch:
T2600G-28TS# reset
27.12 reboot Description
The reboot command is used to reboot the Switch. To avoid damage, please don’t turn off the device while rebooting.
Syntax reboot
Command Mode Privileged EXEC Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Reboot the switch:
T2600G-28TS# reboot
205
27.13 reboot-schedule Description
This reboot-schedule command is used to configure the switch to reboot at a certain time point. To delete the reboot schedule settings, please use the reboot-schedule cancel command.
Syntax
reboot-schedule at time [ date ] [ save_before_reboot ]
reboot-schedule in interval [ save_before_reboot ]
reboot-schedule cancel
Parameter
time —— Specify the time point for the switch to reboot, in the format of hh:mm.
date —— Specify the date for the switch to reboot, in the format of DD:MM:YYYY. The date should be within 30 days.
save_before_reboot —— Save the configuration file before the switch reboots.
interval —— Specify a time period after which the switch reboots. It ranges from 1 to 43200 minutes.
cancel —— Delete the reboot schedule settings.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
User Guidelines In the command reboot-schedule at time [ date ] [ save_before_reboot ], if no date is specified and the time you set here is later than the time that this command is executed, the switch will reboot later that day; otherwise the switch will reboot at the time point the next day.
Example
Specify the switch to save the configuration files and reboot in 200 minutes,:
T2600G-28TS(config)# reboot-schedule in 200 save_before_reboot
206
27.14 copy running-config startup-config Description
The copy running-config startup-config command is used to save the current settings.
Syntax copy running-config startup-config
Command Mode Privileged EXEC Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Save current settings:
T2600G-28TS# copy running-config startup-config
27.15 copy startup-config tftp Description
The copy startup-config tftp command is used to backup the configuration file to TFTP server.
Syntax copy startup-config tftp ip-address ip-addr filename name
Parameter ip-addr —— IP Address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234.
name —— Specify the name for the configuration file which would be backup.
Command Mode Privileged EXEC Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Backup the configuration files to TFTP server with the IP 192.168.0.148 and name this file config.cfg:
207
T2600G-28TS# copy startup-config tftp ip-address 192.168.0.148
filename config
Backup the configuration files to TFTP server with the IP fe80::1234 and name this file config.cfg:
T2600G-28TS# copy startup-config tftp ip-address fe80::1234 filename
config
27.16 copy tftp startup-config Description
The copy tftp startup-config command is used to download the configuration file to the switch from TFTP server.
Syntax copy tftp startup-config ip-address ip-addr filename name
Parameter ip-addr —— IP Address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234.
name —— Specify the name for the configuration file which would be downloaded.
Command Mode Privileged EXEC Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Download the configuration file named as config.cfg to the switch from TFTP server with the IP 192.168.0.148:
T2600G-28TS# copy tftp startup-config ip-address 192.168.0.148
filename config
Download the configuration file named as config.cfg to the switch from TFTP server with the IP fe80::1234
T2600G-28TS# copy tftp startup-config ip-address fe80::1234 filename
config
208
27.17 boot application Description
The boot application command is used to configure the image file as startup image or backup image.
Syntax
boot application filename { image1 | image 2 } { startup | backup }
no boot application
Parameter
image1 | image2 —— Specify the image file to be configured. By default, the image1.bin is the startup image and the image2.bin is the backup image.
startup | backup —— Specify the property of the image, either startup image or backup image.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the image2.bin as the startup image:
T2600G-28TS(config)# boot application filename image2 startup
27.18 remove backup-image Description
The remove backup-image command is used to delete the backup-image.
Syntax
remove backup-image
Command Mode
Privileged EXEC Mode
Privilege Requirement
Only Admin level users have access to these commands.
209
Example
Delete the backup image file:
T2600G-28TS# remove backup-image
27.19 firmware upgrade Description
The firmware upgrade command is used to upgrade the switch’s backup image file via the TFTP server. The uploaded firmware file will take place of the Backup Image, and user can chose whether to reboot the switch will the Backup Image.
Syntax firmware upgrade ip-address ip-addr filename name
Parameter ip-addr —— IP Address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234.
name —— Specify the name for the firmware file.
Command Mode
Privileged EXEC Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Upgrade the switch’s backup iamge file with the file firmware.bin in the TFTP server with the IP address 192.168.0.148, and reboot the switch with this firmware:
T2600G-28TS# firmware upgrade ip-address 192.168.0.148 filename
firmware.bin
It will only upgrade the backup image. Continue? (Y/N):y
Operation OK!
Reboot with the backup image? (Y/N): y
Upgrade the switch’s backup iamge file with the file firmware.bin in the TFTP server with the IP address fe80::1234, but do not reboot the switch:
210
T2600G-28TS# firmware upgrade ip-address fe80::1234 filename
firmware.bin
It will only upgrade the backup image. Continue? (Y/N):y
Operation OK!
Reboot with the backup image? (Y/N): n
27.20 boot autoinstall start
Note: Only T2600G-18TS supports this command.
Description The boot autoinstall start command is used to start Auto Install function. To stop the Auto Install function, use no boot autoinstall start.
Syntax boot autoinstall start
no boot autoinstall start
Command mode Global Configuration Mode
Privilege Requirement Only Admin level users have access to these commands.
Example Start Auto Install function:
T2600-18TS(config)# boot autoinstall start
27.21 boot autoinstall persistent-mode
Note: Only T2600G-18TS supports this command.
Description The boot autoinstall persistent-mode command is used to start Auto Install function to next reboot cycle. To diable persistent mode use no boot autoinstall persistent-mode.
Syntax boot autoinstall persistent-mode
no boot autoinstall persistent-mode
211
Command mode Global Configuration Mode
Privilege Requirement Only Admin level users have access to these commands.
Example Start Auto Install function:
T2600-18TS(config)# boot autoinstall persistent-mode
27.22 boot autoinstall auto-save
Note: Only T2600G-18TS supports this command.
Description The boot autoinstall auto-save command is used to automatically save the new configuration file that was downloaded by Auto Install function to start-up configuration file Auto Install. To disable auto-save configuration feature use no boot autoinstall auto-save.
Syntax boot autoinstall auto-save
no boot autoinstall auto-save
Command mode Global Configuration Mode
Privilege Requirement Only Admin level users have access to these commands.
Example Configure Auto Install function to auto-save new configuration file to start-up configuration file:
T2600-18TS(config)# boot autoinstall auto-save
27.23 boot autoinstall auto-reboot
Note: Only T2600G-18TS supports this command.
212
Description The boot autoinstall auto-reboot command is used to automatically reboot the switch after Auto Install function is completed successfully. To disable auto-reboot feature use no boot autoinstall auto-reboot.
Syntax boot autoinstall auto-reboot
no boot autoinstall auto-reboot
Command mode Global Configuration Mode
Privilege Requirement Only Admin level users have access to these commands.
Example Configure the switch to auto reboot after Auto Install function completed successfully:
T2600-18TS(config)# boot autoinstall auto-reboot
27.24 boot autoinstall retry-count
Note: Only T2600G-18TS supports this command.
Description The boot autoinstall retry-count command is used to configure retry count when Auto Install function uses TFTP to download configuration files in a cycle of Auto Install process. To set retry count to default value use no boot autoinstall retry-count.
Syntax boot autoinstall retry-count count
no boot autoinstall retry-count
Parameter count —— The count of retrying auto install. The value ranges from 1 to 3.
Command Mode Global Configuration Mode
Privilege Requirement Only Admin level users have access to these commands.
213
Example Configure TFTP retry 2 times when download files failed:
T2600-18TS(config)# boot autoinstall retry-count 2
27.25 show boot autoinstall
Note: Only T2600G-18TS supports this command.
Description The show boot autoinstall command is used to display the configuration of Auto Install function.
Syntax show boot autoinstall
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the configuration of Auto Install function:
T2600-18TS# show boot autoinstall
27.26 show boot autoinstall downloaded-config
Note: Only T2600G-18TS supports this command.
Description The show boot autoinstall downloaded-config command is used to display the configuration file which downloaded by Auto Install.
Syntax show boot autoinstall downloaded-config
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
214
Example Display the configuration file which downloaded by Auto Install:
T2600-18TS# show boot autoinstall downloaded-config
27.27 ping Description
The ping command is used to test the connectivity between the switch and one node of the network.
Syntax ping [ ip | ipv6 ] { ip_addr } [ -n count ] [ -l count ] [ -i count ]
Parameter ip —— The type of the IP address for ping test should be IPv4.
ipv6 —— The type of the IP address for ping test should be IPv6.
ip_addr —— The IP address of the destination node for ping test. If the parameter ip/ipv6 is not selected, both IPv4 and IPv6 addresses are supported, for example 192.168.0.100 or fe80::1234.
-n count —— The amount of times to send test data during Ping testing. It ranges from 1 to 10. By default, this value is 4.
-l count —— The size of the sending data during ping testing. It ranges from 1 to 1500 bytes. By default, this value is 64.
-i count —— The interval to send ICMP request packets. It ranges from 100 to 1000 milliseconds. By default, this value is 1000.
Command Mode User EXEC Mode and Privileged EXEC Mode
Privilege Requirement
None.
Example To test the connectivity between the switch and the network device with the IP 192.168.0.131, please specify the count (-l) as 512 bytes and count (-i) as 1000 milliseconds. If there is not any response after 8 times’ Ping test, the connection between the switch and the network device is failed to establish:
T2600G-28TS# ping 192.168.0.131 –n 8 –l 512
To test the connectivity between the switch and the network device with the IP fe80::1234, please specify the count (-l) as 512 bytes and count (-i) as 1000
215
milliseconds. If there is not any response after 8 times’ Ping test, the connection between the switch and the network device is failed to establish:
T2600G-28TS# ping fe80::1234 –n 8 –l 512
27.28 tracert Description
The tracert command is used to test the connectivity of the gateways during its journey from the source to destination of the test data.
Syntax tracert [ ip | ipv6 ] ip_addr [ maxHops ]
Parameter
ip —— The type of the IP address for tracert test should be IPv4.
ipv6 —— The type of the IP address for tracert test should be IPv6.
ip_addr —— The IP address of the destination device. If the parameter ip/ipv6 is not selected, both IPv4 and IPv6 addresses are supported, for example 192.168.0.100 or fe80::1234.
maxHops —— The maximum number of the route hops the test data can pass though. It ranges from 1 to 30. By default, this value is 4.
Command Mode User EXEC Mode and Privileged EXEC Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Test the connectivity between the switch and the network device with the IP 192.168.0.131. If the destination device has not been found after 20 maxHops, the connection between the switch and the destination device is failed to establish:
T2600G-28TS# tracert 192.168.0.131 20
Test the connectivity between the switch and the network device with the IP fe80::1234. If the destination device has not been found after 20 maxHops, the connection between the switch and the destination device is failed to establish:
T2600G-28TS# tracert fe80::1234 20
216
27.29 show system-info Description
The show system-info command is used to display System Description, System Name, System Location, Contact Information, Hardware Version, Software Version, Bootloader Version, Mac Address, System Time, Run Time and so on.
Syntax show system-info
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the system information:
T2600G-28TS# show system-info
27.30 show system-info interface Description
The show system-info interface command is used to display the utilization of the connected Ethernet port.
Syntax
show system-info interface [ gigabitEthernet port ]
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the utilization of port 18:
T2600G-28TS# show system-info interface gigabitEthernet 1/0/18
217
27.31 show image-info
Description
The show imsage-info command is used to display the information of image files in the system.
Syntax
show image-info
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Display the system image files’ information:
T2600G-28TS# show image-info
27.32 show boot
Description
The show boot command is used to display the boot configuration of the system.
Syntax
show boot
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Display the system boot configuration information:
T2600G-28TS# show boot
218
27.33 show running-config Description
The show running-config command is used to display the current operating configurations of the system or of a specified port.
Syntax show running-config [ all ]
Parameter all —— Displays all the current operating configurations. Without this option, only the configurations that differ from the default value will be displayed.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the configurations that differ from the default value:
T2600G-28TS# show running-config
27.34 show running-config | Description
The show running-config | command is used to filter the output information with the keyword you specify. “|” is a separator indicating the information will be filtered.
Syntax show running-config | { [exclude exclude-keyword ] [ include include-keyword } ]
Parameter exclude-keyword —— The operating configuration excluding this keyword wil be displayed.
include-keyword —— The operating configuration including this keyword wil be displayed.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
219
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the operating configuration that includes the “vlan” keyword:
T2600G-28TS# show running-config | include vlan
27.35 show startup-config Description
The show startup-config command is used to display the current configuration saved in the switch. These configuration settings will not be lost the next time you reboot the switch.
Syntax show startup-config
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the saved configuration:
T2600G-28TS# show startup-config
27.36 show system-time Description
The show system-time command is used to display the time information of the switch.
Syntax show system-time
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
220
Example Display the time information of the switch
T2600G-28TS# show system-time
27.37 show system-time dst Description
The show system-time dst command is used to display the DST time information of the switch.
Syntax show system-time dst
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the DST time information of the switch
T2600G-28TS# show system-time dst
27.38 show system-time ntp Description
The show system-time ntp command is used to display the NTP mode configuration information.
Syntax show system-time ntp
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the NTP mode configuration information of the switch:
T2600G-28TS# show system-time ntp
221
27.39 show cable-diagnostics interface
gigabitEthernet Description
The show cable-diagnostics interface gigabitEthernet command is used to display the cable diagnostics of the connected Ethernet Port, which facilitates you to check the connection status of the cable connected to the switch, locate and diagnose the trouble spot of the network.
Syntax show cable-diagnostics interface gigabitEthernet port
Parameter port —— The number of the port which is selected for Cable test.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement None.
Example Show the cable-diagnostics of port 3:
T2600G-28TS# show cable-diagnostics interface gigabitEthernet 1/0/3
27.40 show cable-diagnostics careful interface Description
The show cable-diagnostics careful interface gigabitEthernet command is used to display the connection status of the cable connected to the switch. When taking the careful cable test, the switch will only test the cable for the port which is in the link-down status.
Syntax show cable-diagnostics careful interface [ gigabitEthernet port ]
Parameter port —— The number of the port which is selected for Cable test.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
222
Privilege Requirement
None.
Example Show the cable-diagnostics of port 3:
T2600G-28TS# show cable-diagnostics careful interface gigabitEthernet
1/0/3
27.41 show cpu-utilization
Description
The show cpu-utilization command is used to display the system’s CPU utilization in the last 5 seconds/1minute/5minutes.
Syntax
show cpu-utilization
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the CPU utilization information of the switch:
T2600G-28TS# show cpu-utilization
27.42 show memory-utilization Description
The show memory-utilization command is used to display the system’s memory utilization in the last 5 seconds/1minute/5minutes.
Syntax
show memory-utilization
Command Mode
Privileged EXEC Mode and Any Configuration Mode
223
Privilege Requirement
None.
Example
Display the memory utilization information of the switch:
T2600G-28TS# show memory-utilization
224
Chapter 28 IPv6 Address Configuration Commands
The IPv6 address configuration commands are provided in the Interface Configuration Mode, which includes the routed port, the port-channel interface and the VLAN interface. Enter the configuration mode of these Layer 3 interfaces and configure their IPv6 parameters.
28.1 ipv6 enable Description
This command is used to enable the IPv6 function on the speicified Layer 3 interface. IPv6 function should be enabled before the IPv6 address configuration management. By default it is enabled on VLAN interface 1. IPv6 function can only be enabled on one Layer 3 interface at a time.
If the IPv6 function is disabled, the corresponding IPv6 netstack and IPv6-based modules will be invalid, for example SSHv6, SSLv6, TFTPv6 etc. To disable the IPv6 function, please use no ipv6 enable command.
Syntax
ipv6 enable no ipv6 enable
Command Mode
Interface Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the IPv6 function on the VLAN interface 1:
T2600G-28TS(config)# interface vlan 1
T2600G-28TS(config-if)# ipv6 enable
28.2 ipv6 address autoconfig Description
This command is used to enable the automatic configuration of the ipv6 link-local address. The switch has only one ipv6 link-local address, which can be configured automatically or manually. The general ipv6 link-local address
225
has the prefix as fe80::/10. IPv6 routers cannot forward packets that have link-local source or destination addresses to other links. The autuconfigured ipv6 link-local address is in EUI-64 format. To verify the uniqueness of the link-local address, the manually configured ipv6 link-local address will be deleted when the autoconfigured ipv6 link-local address takes effect.
Syntax
ipv6 address autoconfig
Configuration Mode
Interface Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the automatic configuration of the ipv6 link-local address on VLAN interface 1:
T2600G-28TS(config)# interface vlan 1
T2600G-28TS(config-if)# ipv6 address autoconfig
28.3 ipv6 address link-local Description
The ipv6 address link-local command is used to configure the ipv6 link-local address manually on a specified interface. To delete the configured link-local address, please use no ipv6 address link-local command.
Syntax
ipv6 address ipv6-addr link-local
no ipv6 address ipv6-addr link-local
Parameter
ipv6-addr —— The link-local address of the interface. It should be a standardized IPv6 address with the prefix fe80::/10, otherwise this command will be invalid.
Configuration Mode
Interface Configuration Mode
226
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the link-local address as fe80::1234 on the VLAN interface 1:
T2600G-28TS(config)# interface vlan 1
T2600G-28TS(config-if)# ipv6 address fe80::1234 link-local
28.4 ipv6 address dhcp Description
The ipv6 address dhcp command is used to enable the DHCPv6 Client function. When this function is enabled, the Layer 3 interface will try to obtain IP from DHCPv6 server. To delete the allocated IP from DHCPv6 server and disable the DHCPv6 Client function, please use no ipv6 address dhcp command.
Syntax
ipv6 address dhcp
no ipv6 address dhcp
Configuration Mode
Interface Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the DHCP Client function on VLAN interface 1:
T2600G-28TS(config)# interface vlan 1
T2600G-28TS(config-if)# ipv6 address dhcp
28.5 ipv6 address ra Description
This command is used to configure the interface’s global IPv6 address according to the address prefix and other configuration parameters from its
227
received RA(Router Advertisement) message. To disable this function, please use no ipv6 address ra command.
Syntax
ipv6 address ra
no ipv6 address ra
Configuration Mode
Interface Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the automatic ipv6 address configuration function to obtain IPv6 address through the RA message on VLAN interface 1:
T2600G-28TS(config)# interface vlan 1
T2600G-28TS(config-if)# ipv6 address ra
28.6 ipv6 address eui-64 Description
This command is used to manually configure a global IPv6 address with an extended unique identifier (EUI) in the low-order 64 bits on the interface. Specify only the network prefix. The last 64 bits are automatically computed from the switch MAC address. To remove an EUI-64 IPv6 address from the interface, please use the no ipv6 address eui-64 command.
Syntax
ipv6 address ipv6-addr eui-64
no ipv6 address ipv6-addr eui-64
Parameter
ipv6-addr —— Global IPv6 address with 64 bits network prefix, for example 3ffe::/64.
Configuration Mode
Interface Configuration Mode
228
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure an EUI-64 global address on the interface with the network prefix 3ffe::/64:
T2600G-28TS(config)# interface vlan 1
T2600G-28TS(config-if)# ipv6 address 3ffe::/64 eui-64
28.7 ipv6 address Description
This command is used to manually configure a global IPv6 address on the interface. To remove a global IPv6 address from the interface, please use no ipv6 address command.
Syntax
ipv6 address ipv6-addr
no ipv6 address ipv6-addr
Parameter
ipv6-addr —— Global IPv6 address with network prefix, for example 3ffe::1/64.
Configuration Mode
Interface Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the global address 3001::1/64 on VLAN interface 1:
T2600G-28TS(config)# interface vlan 1
T2600G-28TS(config-if)# ipv6 address 3001::1/64
229
28.8 show ipv6 interface Description
This command is used to display the configured ipv6 information of the management interface, including ipv6 function status, link-local address and global address, ipv6 multicast groups etc.
Syntax
show ipv6 interface
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the ipv6 information of the management interface:
T2600G-28TS(config)# show ipv6 interface
230
Chapter 29 Ethernet Configuration Commands
Ethernet Configuration Commands can be used to configure the Bandwidth Control, Negotiation Mode and Storm Control for Ethernet ports.
29.1 interface gigabitEthernet Description
The interface gigabitEthernet command is used to enter the Interface gigabitEthernet Configuration Mode and configure the corresponding Gigabit Ethernet port.
Syntax
interface gigabitEthernet port
Parameter
port —— The Ethernet port number.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
To enter the Interface gigabitEthernet Configuration Mode and configure port 2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
29.2 interface range gigabitEthernet Description
The interface range gigabitEthernet command is used to enter the interface range gigabitEthernet Configuration Mode and configure multiple Gigabit Ethernet ports at the same time.
231
Syntax
interface range gigabitEthernet port-list
Parameter
port-list —— The list of Ethernet ports.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines Command in the Interface Range gigabitEthernet Mode is executed independently on all ports in the range. It does not affect the execution on the other ports at all if the command results in an error on one port.
Example
To enter the Interface range gigabitEthernet Configuration Mode, and configure ports 1, 2, 3, 6, 7 and 9 at the same time by adding them to one port-list:
T2600G-28TS(config)# interface range gigabitEthernet
1/0/1-3,1/0/6-7,1/0/9
29.3 description Description
The description command is used to add a description to the Ethernet port. To clear the description of the corresponding port, please use no description command.
Syntax
description string
no description
Parameter
string —— Content of a port description, ranging from 1 to 16 characters.
232
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Add a description Port_5 to port 1/0/5:
T2600G-28TS(config)# interface gigabitEthernet 1/0/5
T2600G-28TS(config-if)# description Port_5
29.4 shutdown Description
The shutdown command is used to disable an Ethernet port. To enable this port again, please use no shutdown command.
Syntax shutdown
no shutdown
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Disable port 1/0/3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# shutdown
233
29.5 flow-control Description
The flow-control command is used to enable the flow-control function for a port. To disable the flow-control function for this corresponding port, please use no flow-control command. With the flow-control function enabled, the Ingress Rate and Egress Rate can be synchronized to avoid packet loss in the network.
Syntax flow-control
no flow-control
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Enable the flow-control function for port 1/0/3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# flow-control
29.6 duplex Description
The duplex command is used to configure the Duplex Mode for an Ethernet port. To return to the default configuration, please use no duplex command.
Syntax
duplex { auto | full | half }
no duplex
Parameter
auto | full | half —— The duplex mode of the Ethernet port. There are three options: auto-negotiation mode, full-duplex mode and half-duplex mode. By default the Gigabit Ethernet port is auto-negotiation mode.
234
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Configure the Duplex Mode as full-duplex for port 1/0/3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# duplex full
29.7 jumbo Description
The jumbo command is used to allow the jumbo frame to pass through this port. To disable this feature, please use no jumbo command. This feature is disabled by default.
Syntax jumbo
no jumbo
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Allow jumbo frame on port 1/0/3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# jumbo
29.8 jumbo-size
Note: Only T2600G-18TS supports this command.
235
Description The jumbo-size command is used to specify the size of jumbo frames.
Syntax jumbo-size size
Parameter size —— The value of jumbo frames. It ranges from 1518 to 9216 bytes, and the default is 1518 bytes.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Globally configure the size of jumbo frames as 9216:
T2600G-18TS(config)# jumbo-size 9216
29.9 speed Description
The speed command is used to configure the Speed Mode for an Ethernet port. To return to the default configuration, please use no speed command.
Syntax speed { 10 | 100 | 1000 | auto }
no speed
Parameter 10 | 100 | 1000 | auto —— The speed mode of the Ethernet port. There are four options: 10Mbps, 100Mbps, 1000Mbps and Auto negotiation mode (default).
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Configure the Speed Mode as 100Mbps for port 1/0/3:
236
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# speed 100
29.10 storm-control pps
Note: T2600G-18TS doesn’t support this command.
Description The storm-control pps command is used to configure the storm control mode as pps(packets per second) on an interface. To disable the pps mode, please use no storm-control pps command.
Syntax storm-control pps no storm-control pps
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines This command should be used along with the storm-control command to enable the storm control function and specify the detailed parameters in pps mode.
Example Set the storm control mode as pps on port 1/0/5:
T2600G-28TS(config)# interface gigabitEthernet 1/0/5
T2600G-28TS(config-if)# storm-control pps
29.11 storm-control Description
The storm-control command is used to enable the broadcast, multicast, or unicast strom control function and to set threshold levels on an interface. To disable the storm control function, please use no storm-control command.
237
Syntax storm-control { broadcast | multicast | unicast } { kbps | ratio | pps } { rate } no storm-control { broadcast | multicast | unicast }
Parameter broadcast | multicast | unicast —— Enable broadcast/multicast/unicast storm control on the interface. kbps | ratio | pps —— Specify the storm control type. kbps: Specify the threshold in kbits per second. ratio: Specify the threshold as a percentage of the bandwidth. pps: Specify the threshold in packets per second. rate —— Specify the bandwidth for receiving packets on the port. The specified type of packet traffic exceeding the bandwidth will be discarded. For kbps, the rate ranges from 1 to 1000000 kbps. For ratio, the rate ranges from 1 to 100 percent. For pps, the rate ranges from 1 to 1488000 packets per second.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines Before you configure the storm-control type as kbps or ratio, pelease ensure that the port is not in pps mode.
Example Configure the broadcast storm control rate as 1000 kbps on port 1/0/5:
T2600G-28TS(config)# interface gigabitEthernet 1/0/5
T2600G-28TS(config-if)# storm-control broadcast kbps 1000
29.12 bandwidth Description
The bandwidth command is used to configure the bandwidth limit for an Ethernet port. To disable the bandwidth limit, please use no bandwidth command.
238
Syntax bandwidth {[ ingress ingress-rate ] [ egress egress-rate ]}
no bandwidth { all | ingress | egress }
Parameter ingress-rate —— Specify the bandwidth for receiving packets. Range: 1-1000000Kbps for the gigaport.
egress-rate —— Specify the bandwidth for sending packets. Range: 1-1000000Kbps for the gigaport.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the ingress-rate as 5120Kbps and egress-rate as 1024Kbps for port 1/0/5:
T2600G-28TS(config)# interface gigabitEthernet 1/0/5
T2600G-28TS(config-if)# bandwidth ingress 5120 egress 1024
29.13 clear counters Description
The clear counters command is used to clear the statistics information of all the Ethernet ports and port channels.
Syntax clear counters
clear counters interface [ gigabitEthernet port ] [ port-channel port-channel-id ]
Parameter port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode Privileged EXEC Mode and Any Configuration Mode
239
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Clear the statistic information of all ports and port channels:
T2600G-28TS(config)# clear counters
29.14 show interface status Description
The show interface status command is used to display the connection status of the Ethernet port/port channel.
Syntax show interface status [ gigabitEthernet port ] [ port-channel port-channel-id ]
Parameter port —— The Ethernet port number.
port-channel-id —— The ID of the port channel..
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the connection status of all ports and port channels:
T2600G-28TS(config)# show interface status
Display the connection status of port 1/0/1:
T2600G-28TS(config)# show interface status gigabitEthernet 1/0/1
29.15 show interface counters Description
The show interface counters command is used to display the statistics information of all ports/port channels.
Syntax show interface counters [ gigabitEthernet port ] [ port-channel port-channel-id ]
240
Parameter port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the statistics information of all Ethernet ports and port channels:
T2600G-28TS(config)# show interface counters
Display the statistics information of port 1/0/2:
T2600G-28TS(config)# show interface counters gigabitEthernet 1/0/2
29.16 show interface configuration Description
The show interface configuration command is used to display the configurations of all ports and port channels, including Port-status, Flow Control, Negotiation Mode and Port-description.
Syntax show interface configuration [ gigabitEthernet port ] [ port-channel port-channel-id ]
Parameter port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the configurations of all Ethernet ports and port channels:
T2600G-28TS(config)# show interface configuration
Display the configurations of port 1/0/2:
241
T2600G-28TS(config)# show interface configuration gigabitEthernet 1/0/2
29.17 show storm-control Description
The show storm-control command is used to display the storm-control information of Ethernet ports.
Syntax show storm-control interface [ gigabitEthernet port-list ] [ port-channel port-channel-id-list ]
Parameter port-list ——The list of Ethernet ports.
port-channel-id-list —— The list of port channels.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the storm-control information of port 4, 5, 6, and 7:
T2600G-28TS(config)# show storm-control interface gigabitEthernet
1/0/4-7
29.18 show bandwidth Description
The show bandwidth command is used to display the bandwidth-limit information of Ethernet ports.
Syntax show bandwidth interface [ gigabitEthernet port-list ] [ port-channel port-channel-id-list ]
Parameter port-list ——The list of Ethernet ports.
port-channel-id-list —— The list of port channels.
242
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the bandwidth-limit information of port 1/0/4:
T2600G-28TS(config)# show bandwidth interface gigabitEthernet 1/0/4
243
Chapter 30 QoS Commands
QoS (Quality of Service) function is used to optimize the network performance. It provides you with network service experience of a better quality.
30.1 qos (For T2600G-18TS only) Description
The qos command is used to configure CoS (Class of Service) based on port. To return to the default configuration, please use no qos command.
Syntax qos tc-id
no qos
Parameter tc-id —— The priority of port. It ranges from 0 to 7, which represent TC0-TC7 respectively. By default, the priority is 0.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines Port priority is one property of the port. When the port priority is specified, the data will be classified into the egress queue based on the tc value of the current port.
Example Configure the priority of port 5 as 3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/5
T2600G-28TS(config-if)# qos 3
244
30.2 qos (For other switches) Description
The qos command is used to configure CoS (Class of Service) based on port. To return to the default configuration, please use no qos command.
Syntax qos cos-id
no qos
Parameter cos-id —— The priority of port. It ranges from 0 to 7, which represent CoS0-CoS7 respectively. By default, the priority is 0.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines Port priority is one property of the port. When the port priority is specified, the data will be classified into the egress queue based on the CoS value of the ingress port and the mapping relation between the CoS and TC in IEEE 802.1P.
Example Configure the priority of port 5 as 3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/5
T2600G-28TS(config-if)# qos 3
30.3 qos cos
Note: Only T2600G-18TS supports this command.
Description The qos cos command is used to enable the mapping relation between IEEE802.1P Priority and TC egress queue. To disable the mapping relation, please use no qos cos command.
245
Syntax qos cos
no qos cos
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines IEEE 802.1P gives the Pri field in IEEE 802.1Q tag a recommended definition. When the mapping relation between IEEE 802.1P Priority and TC egress queue is enabled, the data will be classified into the egress queue based on this mapping relation.
Example Enable the mapping relation between IEEE 802.1P Priority and egress queue:
T2600G-18TS (config)# qos cos
30.4 qos dscp Description
The qos dscp command is used to enable the mapping relation between DSCP Priority and CoS value. To disable the mapping relation, please use no qos dscp command.
Syntax qos dscp
no qos dscp
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines DSCP (DiffServ Code Point) is a new definition to IP ToS field given by IEEE. DSCP priorities are mapped to the corresponding 802.1p priorities. IP
246
datagram will be classified into the egress queue based on the mapping relation between DSCP priority and CoS value.
Example Enable the mapping relation between DSCP Priority and CoS value:
T2600G-28TS(config)# qos dscp
30.5 qos queue cos-map Description
The qos queue cos-map command is used to configure the mapping relation between IEEE 802.1P priority tag/IEEE 802.1Q tag, CoS value and the TC egress queue. To return to the default configuration, please use no qos queue cos-map command. When 802.1P Priority is enabled, the packets with 802.1Q tag are mapped to different priority levels based on 802.1P priority mode. The untagged packets are mapped based on port priority mode.
Syntax qos queue cos-map { tag/cos-id } { tc-id }
no qos queue cos-map
Parameter tag/cos-id —— The 8 priority levels defined by IEEE 802.1P or the priority level the packets with tag are mapped to, which ranges from CoS 0 to CoS 7.
tc-id —— The egress queue the packets with tag are mapped to. It ranges from 0 to 7, which represents TC0 toTC7 respectively.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines 1. By default, the mapping relation between tag/cos and the egress queue
is: 0/CoS 0-TC1, 1/CoS 1-TC0, 2/CoS 2-TC2, 3/CoS 3-TC3, 4/CoS 4-TC4, 5/CoS 5-TC5, 6/CoS 6-TC6, 7/CoS 7-TC7.
2. Among the priority levels TC0-TC7, the bigger value, the higher priority.
247
Example Map CoS 5 to TC 2:
T2600G-28TS(config)# qos queue cos-map 5 2
30.6 qos queue dscp-map (For T2600G-18TS only) Description
The qos queue dscp-map command is used to configure the mapping relation between DSCP Priority and the CoS value. To return to the default configuration, please use no qos queue dscp-map command. DSCP (DiffServ Code Point) is a new definition to IP ToS field given by IEEE. This field is used to divide IP datagram into 64 priorities. When DSCP Priority is enabled, IP datagram are mapped to different priority levels based on DSCP priority mode; non-IP datagram with IEEE 802.1Q tag are mapped to different priority levels based on IEEE 802.1P priority mode if IEEE 802.1P Priority is enabled; the untagged non-IP datagram are mapped based on port priority mode.
Syntax qos queue dscp-map { dscp-list } { tc-id }
no qos queue dscp-map
Parameter dscp-list —— List of DSCP value. One or several DSCP values can be typed using comma to separate. Use a hyphen to designate a range of values, for instance, 1,4-7,11 indicates choosing 1,4,5,6,7,11. The DSCP value ranges from 0 to 63.
tc-id —— The priority level the packets with tag are mapped to, which ranges from TC 0 to TC 7.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines By default, the mapping relation between DSCP value and the egress queue is: (0-7)-TC 0, (8-15)-TC 1, (16-23)-TC 2, (24-31)-TC 3, (32-39)-TC 4, (40-47)-TC 5, (48-55)-TC 6, (56-63)-TC 7.
248
Example Map DSCP values 10-12 to TC 2:
T2600G-28TS(config)# qos queue dscp-map 10-12 2
30.7 qos queue dscp-map (For other switches) Description
The qos queue dscp-map command is used to configure the mapping relation between DSCP Priority and the CoS value. To return to the default configuration, please use no qos queue dscp-map command. DSCP (DiffServ Code Point) is a new definition to IP ToS field given by IEEE. This field is used to divide IP datagram into 64 priorities. When DSCP Priority is enabled, IP datagram are mapped to different priority levels based on DSCP priority mode; non-IP datagram with IEEE 802.1Q tag are mapped to different priority levels based on IEEE 802.1P priority mode if IEEE 802.1P Priority is enabled; the untagged non-IP datagram are mapped based on port priority mode.
Syntax qos queue dscp-map { dscp-list } { cos-id }
no qos queue dscp-map
Parameter dscp-list —— List of DSCP value. One or several DSCP values can be typed using comma to separate. Use a hyphen to designate a range of values, for instance, 1,4-7,11 indicates choosing 1,4,5,6,7,11. The DSCP value ranges from 0 to 63.
cos-id —— The priority level the packets with tag are mapped to, which ranges from CoS 0 to CoS 7.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines By default, the mapping relation between DSCP value and the CoS value is: (0-7)-CoS 0, (8-15)-CoS 1, (16-23)-CoS 2, (24-31)-CoS 3, (32-39)-CoS 4, (40-47)-CoS 5, (48-55)-CoS 6, (56-63)-CoS 7.
249
Example Map DSCP values 10-12 to CoS 2:
T2600G-28TS(config)# qos queue dscp-map 10-12 2
30.8 qos queue mode Description
The qos queue mode command is used to configure the Schedule Mode. To return to the default Equal-Mode, please use no qos queue mode command. When the network is congested, the program that many packets complete for resources must be solved, usually in the way of queue scheduling. The switch will control the forwarding sequence of the packets according to the priority queues and scheduling algorithms you set. On this switch, the priority levels are labeled as TC0, TC1,TC2 … TC7.
Syntax qos queue mode { sp | wrr | spwrr | equ }
no qos queue mode
Parameter sp —— Strict-Priority Mode. In this mode, the queue with higher priority will occupy the whole bandwidth. Packets in the queue with lower priority are sent only when the queue with higher priority is empty.
wrr —— Weight Round Robin Mode. In this mode, packets in all the queues are sent in order based on the weight value for each queue. The weight values of TC0, TC1, TC2, TC3, TC4, TC5,TC6 and TC7 are customized in qos queue weight command and their default values are 1, 2, 4, 8, 16, 32, 64 and 127 respectively.
spwrr —— Strict-Priority + Weight Round Robin Mode. In this mode, the switch provides two scheduling groups, SP group and WRR group. SP group is processed prior to WRR group. Queues in SP group are scheduled strictly based on Strict-Priority mode while the queues inside WRR group follow the WRR mode. In SP+WRR mode, TC7 and the queue with its weight value set as 0 are in the SP group; other queues, with none-zero weight value, belong to the WRR group and the weight value can be customized in qos queue weight command. The weight values of TC0, TC1, TC2, TC3, TC4, TC5 and TC6 are 1, 2, 4, 8, 16, 32 and 64 respectively, while the value of TC7 is 0 and non-configurable.
250
equ —— Equal-Mode. In this mode, all the queues occupy the bandwidth equally. The weight value ratio of all the queues is 1:1:1:1:1:1:1:1
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Specify the Schedule Mode as Weight Round Robin Mode:
T2600G-28TS(config)# qos queue mode wrr
30.9 qos queue weight Description
The qos queue weight command is used to configure weight value of each queue after the Schedule Mode is specified as WRR or SP+WRR. The switch will control the forwarding sequence of the packets according to the priority queues and scheduling algorithms you set. On this switch, the priority levels are labeled as TC0, TC1, TC2, TC3, TC4, TC5,TC6 and TC7.
Syntax qos queue weight { tc-id } { weight-value }
Parameter tc-id —— The ID of the TC queue, ranging from 0 to 7.
weight-value —— Configure the weight value of the specified TC queue.
When the schedule mode is specified as WRR, the weight value ranges from 1 to 127. The 8 queues will take up the bandwidth according to their ratio. The default values of TC0, TC1, TC2, TC3, TC4, TC5,TC6 and TC7 are 1, 2, 4, 8, 16, 32, 64 and 127 respectively.
When the schedule mode is specified as SP+WRR, the weight value ranges from 0 to 127. TC7 and the queue with its weight value set as 0 are in the SP group; other queues, with none-zero weight value, belong to the WRR group. In this SP+WRR scheduling mode, the queues in the SP group is scheduled preferentially (TC6>TC5>TC4>TC3>TC2>TC1>TC0 in strict priority). When there is no packets to be sent in the SP group, the queues in the WRR group will be scheduled according to the weight value of each queue. The default
251
weight values of TC0, TC1, TC2, TC3, TC4, TC5 and TC6 are 1, 2, 4, 8, 16, 32 and 64 respectively, while the value of TC7 is 0 and non-configurable.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Specify the Schedule Mode as Weight Round Robin Mode, with the weight values of TC0, TC1, TC2 and TC3 as 4, 7, 15 and 24:
T2600G-28TS(config)# qos queue mode wrr
T2600G-28TS(config)# qos queue weight 0 4
T2600G-28TS(config)# qos queue weight 1 7
T2600G-28TS(config)# qos queue weight 2 15
T2600G-28TS(config)# qos queue weight 3 24
30.10 show qos interface Description
The show qos interface command is used to display the configuration of QoS based on port priority.
Syntax show qos interface [ gigabitEthernet port-list ] [ port-channel lagid-list ]
Parameter
port-list ——The list of Ethernet ports.
lagid-list —— The list of LAGs.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the configuration of QoS for all ports and LAGs:
T2600G-28TS# show qos interface
252
Display the configuration of QoS for ports 1/0/1-4:
T2600G-28TS# show qos interface gigabitEthernet 1/0/1-4
30.11 show qos cos-map Description
The show qos cos-map command is used to display the configuration of IEEE 802.1P Priority and the mapping relation between cos-id and tc-id.
Syntax show qos cos-map
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the configuration of IEEE 802.1P Priority and the mapping relation between cos-id and tc-id:
T2600G-28TS# show qos cos-map
30.12 show qos dscp-map Description
The show qos dscp-map command is used to display the configuration of DSCP Priority.
Syntax show qos dscp-map
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the configuration of DSCP Priority:
T2600G-28TS# show qos dscp-map
253
30.13 show qos queue mode Description
The show qos queue mode command is used to display the schedule rule of the egress queues.
Syntax show qos queue mode
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the schedule rule of the egress queues:
T2600G-28TS# show qos queue mode
30.14 show qos status Description
The show qos status command is used to display the status of IEEE 802.1P priority and DSCP priority.
Syntax show qos status
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the status of IEEE 802.1P priority and DSCP priority:
T2600G-28TS# show qos status
254
Chapter 31 Port Mirror Commands
Port Mirror refers to the process of forwarding copies of packets from one port to a monitoring port. Usually, the monitoring port is connected to data diagnose device, which is used to analyze the monitored packets for monitoring and troubleshooting the network.
31.1 monitor session destination interface Description
The monitor session destination interface command is used to configure the monitoring port. Each monitor session has only one monitoring port. To change the monitoring port, please use the monitor session destination interface command by changing the port value. The no monitor session command is used to delete the corresponding monitoring port or monitor session.
Syntax monitor session session_num destination interface gigabitEthernet port
no monitor session session_num destination interface gigabitEthernet port
no monitor session session_num
Parameter session_num —— The monitor session number, can only be specified as 1.
port —— The monitoring port number.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Create monitor session 1 and configure port 1/0/1 as the monitoring port:
T2600G-28TS(config)# monitor session 1 destination interface
gigabitEthernet 1/0/1
Delete the monitoring port 1/0/2 from monitor session 1:
255
T2600G-28TS(config)# no monitor session 1 destination interface
gigabitEthernet 1/0/2
Delete the monitor session 1:
T2600G-28TS(config)# no monitor session 1
31.2 monitor session source interface Description
The monitor session source interface command is used to configure the monitored port. To delete the corresponding monitored port, please use no monitor session source interface command.
Syntax monitor session session_num source interface gigabitEthernet port-list mode
no monitor session session_num source interface gigabitEthernet port-list mode
Parameter session_num —— The monitor session number, can only be specified as 1.
port-list —— List of monitored port. It is multi-optional.
mode —— The monitor mode. There are three options: rx, tx and both. Rx (ingress monitoring mode), means the incoming packets received by the monitored port will be copied to the monitoring port. Tx (egress monitoring mode), indicates the outgoing packets sent by the monitored port will be copied to the monitoring port. Both (ingress and egress monitoring), presents the incoming packets received and the outgoing packets sent by the monitored port will both be copied to the monitoring port.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
User Guidelines 1. The monitoring port is corresponding to current interface configuration
mode.
2. Monitored ports number is not limited, but it can’t be the monitoring port at the same time.
256
3. Whether the monitoring port and monitored ports are in the same VLAN or not is not demanded strictly.
4. The monitoring port and monitored ports cannot be link-aggregation member.
Example Create monitor session 1, then configure port 4, 5, 7 as monitored port and enable ingress monitoring:
T2600G-28TS(config)# monitor session 1 source interface
gigabitEthernet 1/0/4-5,1/0/7 rx
Delete port 4 in monitor session 1 and its configuration:
T2600G-28TS(config)# no monitor session 1 source interface
gigabitEthernet 1/0/4 rx
31.3 show monitor session Description
The show monitor session command is used to display the configuration of port monitoring.
Syntax show monitor session [session_num]
Parameter session_num —— The monitor session number, can only be specified as 1. It is optional.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the monitoring configuration of monitor session 1:
T2600G-28TS(config)# show monitor session 1
257
Chapter 32 Port Isolation Commands
Port Isolation provides a method of restricting traffic flow to improve the network security by forbidding the port to forward packets to the ports that are not on its forwarding port list.
32.1 port isolation Description
The port isolation command is used to configure the forward port/port channel list of a port/port channel, so that this port/port channel can only communicate with the ports/port channels on its list. To delete the corresponding configuration, please use no port isolation command.
Syntax port isolation { [ gi-forward-list gi-forward-list ] [ po-forward-list po-forward-list ] }
no port isolation
Parameter gi-forward-list —— The list of Ethernet ports.
po-forward-list —— The list of port channels.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Set port 1, 2, 4 and port channel 2 to the forward list of port 1/0/5:
T2600G-28TS(config)# interface gigabitEthernet 1/0/5
T2600G-28TS(config-if)# port isolation gi-forward-list 1/0/1-2,1/0/4
po-forward-list 2
Set all Ethernet ports and port channels to forward list of port 1/0/2, namely restore to the default setting:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# no port isolation
258
32.2 show port isolation interface Description
The show port isolation interface command is used to display the forward port list of a port/port channel.
Syntax show port isolation interface [ gigabitEthernet port | port-channel port-channel-id ]
Parameter port —— The number of Ethernet port you want to show its forward port list, in the format of 1/0/2.
port-channel-id —— The ID of port channel you want to show its forward port list, ranging from 1 to 6.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the forward-list of port 1/0/2:
T2600G-28TS# show port isolation interface gigabitEthernet 1/0/2
Display the forward-list of all Ethernet ports and port channels:
T2600G-28TS# show port isolation interface
259
Chapter 33 Loopback Detection Commands
With loopback detection feature enabled, the switch can detect loops using loopback detection packets. When a loop is detected, the switch will display an alert or further block the corresponding port according to the configuration.
33.1 loopback-detection (global) Description
The loopback-detection command is used to enable the loopback detection function globally. To disable it, please use no loopback detection command.
Syntax loopback-detection
no loopback-detection
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the loopback detection function globally:
T2600G-28TS(config)# loopback-detection
33.2 loopback-detection interval Description
The loopback-detection interval command is used to define the interval of sending loopback detection packets from switch ports to network, aiming at detecting network loops periodically.
Syntax loopback-detection interval interval-time
Parameter interval-time —— The interval of sending loopback detection packets. It ranges from 1 to 1000 seconds. By default, this value is 30.
260
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Specify the interval-time as 50 seconds:
T2600G-28TS(config)# loopback-detection interval 50
33.3 loopback-detection recovery-time Description
The loopback-detection recovery-time command is used to configure the time after which the blocked port would automatically recover to normal status.
Syntax loopback-detection recovery-time recovery-time
Parameter recovery-time —— The time after which the blocked port would automatically recover to normal status, and the loopback detection would restart. It ranges from 60 to 1000000 seconds. By default, this value is 90.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the recovery-time as 70 seconds:
T2600G-28TS(config)# loopback-detection recovery-time 70
261
33.4 loopback-detection (interface) Description
The loopback-detection command is used to enable the loopback detection function of the specified port. To disable it, please use no loopback-detection command.
Syntax loopback-detection
no loopback-detection
Command Mode Interface Configuration Mode (interface gigabitEthernet | interface range gigabitEthernet | interface port-channel | interface range port-channel )
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the loopback detection function of ports 1-3:
T2600G-28TS(config)# interface range gigabitEthernet 1/0/1-3
T2600G-28TS(Config-if-range)# loopback-detection
33.5 loopback-detection config process-mode Description
The loopback-detection config process-mode command is used to configure the process-mode for the ports by which the switch copes with the detected loops. You also need to configure the recovery mode to remove the block status of the port or VLAN when the process-mode is Port Based or VLAN Based.
Syntax loopback-detection config process-mode { alert | port-based | vlan-based }
Parameter alert —— When a loop is detected, the switch will send a trap message and generate an entry on the log file. It is the default setting.
port-based —— When a loop is detected, the switch will send a trap message and generate an entry on the log file. In addition, the switch will block the port on which the loop is detected and no packets can pass through the port.
262
vlan-based —— When a loop is detected, the switch will send a trap message and generate an entry on the log file. In addition, the switch will block the VLAN in which the loop is detected and only the packets of the blocked VLAN cannot pass through the port.
Command Mode Interface Configuration Mode (interface gigabitEthernet | interface range gigabitEthernet | interface port-channel | interface range port-channel )
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the loopback detection process-mode as port-based for port 2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# loopback-detection config process-mode
port-based
33.6 loopback-detection config recovery-mode Description
The loopback-detection config recovery-mode command is used to configure the recovery-mode for the ports by which the switch copes with the detected loops. Using this command you can remove the block status of the port or VLAN when the process-mode is Port Based or VLAN Based.
Syntax loopback-detection config recovery-mode { auto | manual }
Parameter auto —— Block status can be automatically removed after recovery time.
manual —— Block status can only be removed manually.
Command Mode Interface Configuration Mode (interface gigabitEthernet | interface range gigabitEthernet | interface port-channel | interface range port-channel )
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
263
Example Configure the loopback detection recovery-mode as manual for port 2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# loopback-detection config recovery-mode
manual
33.7 loopback-detection recover Description
The loopback-detection recover command is used to remove the block status of selected ports, recovering the blocked ports to normal status,
Syntax loopback-detection recover
Command Mode Interface Configuration Mode (interface gigabitEthernet | interface range gigabitEthernet | interface port-channel | interface range port-channel )
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Recover the blocked port 1/0/2 to normal status:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# loopback-detection recover
33.8 show loopback-detection global Description
The show loopback-detection global command is used to display the global configuration of loopback detection function such as loopback detection global status, loopback detection interval and loopback detection recovery time.
Syntax show loopback-detection global
264
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the global configuration of loopback detection function:
T2600G-28TS# show loopback-detection global
33.9 show loopback-detection interface Description
The show loopback-detection interface command is used to display the configuration of loopback detection function and the status of the specified Ethernet port.
Syntax show loopback-detection interface [ gigabitEthernet port | port-channel lagid ] [ detail ]
Parameter port —— The Ethernet port number.
lagid —— The number of LAG, ranging from 1 to 14.
detail —— Displays the loop status and block status of the VLAN which the specified port belongs to.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the configuration of loopback detection function and the status of all ports:
T2600G-28TS# show loopback-detection interface
Display the configuration of loopback detection function and the status of port 5:
T2600G-28TS# show loopback-detection interface gigabitEthernet 1/0/5
265
Chapter 34 DDM Commands
The DDM (Digital Diagnostic Monitoring) function allows the user to monitor the status of the SFP modules inserted into the SFP ports on the switch. The user can choose to shut down the monitoring SFP port automatically when specified parameter exceeds the alarm threshold or warning threshold. The monitoring parameters include: Temperature, Voltage, Bias Current, Tx Power and Rx Power.
34.1 ddm state enable Description
The ddm state enable command is used to enable the DDM function on the specified SFP port.
Use the no ddm state enable command to disable the DDM function on this port.
Syntax ddm state enable
no ddm state enable
Default Setting Enabled on all the SFP ports.
Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface range gigabitEthernet)
Example Enable DDM function on port 1/0/25:
T2600G-28TS(config)#interface gigabitEthernet 1/0/25
T2600G-28TS(config-if)#ddm state enable
34.2 ddm shutdown Description
The ddm shutdown command is used to configure whether to shut down the port when an exceeding alarm threshold or warning threshold event is encountered.
266
Syntax ddm shutdown { none | warning | alarm }
Parameter none —— The port will never be shut down regardless of the exceeding alarm threshold and warning threshold events.
warning —— Shut down the port when an exceeding warning threshold event is encountered.
alarm —— Shut down the port when an exceeding alarm threshold event is encountered.
Default Setting none, which means the port will never be shut down regardless of the exceeding alarm threshold and warning threshold events.
Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface range gigabitEthernet)
Example Shut down the port 1/0/25 when an exceeding warning threshold event is encountered:
T2600G-28TS(config)#interface gigabitEthernet 1/0/25
T2600G-28TS(config-if)#ddm shutdown warning
34.3 ddm temperature_threshold Description
The ddm temperature_threshold command is used to configure the threshold of the DDM temperature value.
Syntax ddm temperature_threshold { high_alarm | high_warning | low_alarm | low_warning } value
Parameter high_alarm —— Specify the highest threshold for the alarm. When the operating parameter rises above the value hereinafter, action associated with the alarm will be taken.
267
high_warning ——Specify the highest threshold for the warning. When the operating parameter rises above the value hereinafter, action associated with the warning will be taken.
low_alarm ——Specify the lowest threshold for the alarm. When the operating parameter falls below the value hereinafter, action associated with the alarm will be taken.
low_warning —— Specify the lowest threshold for the warning. When the operating parameter falls below the value hereinafter, action associated with the warning will be taken.
value —— Enter the threshold value in Celsius.
Default Setting None.
Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface range gigabitEthernet)
Example Configure the high_alarm threshold of DDM temperature on the port 1/0/25 as 5:
T2600G-28TS(config)#interface gigabitEthernet 1/0/25
T2600G-28TS(config-if)#ddm temperature_threshold high_alarm 5
34.4 ddm voltage_threshold Description
The ddm voltage_threshold command is used to configure the threshold of the DDM voltage value.
Syntax ddm voltage_threshold { high_alarm | high_warning | low_alarm | low_warning } value
Parameter high_alarm —— Specify the highest threshold for the alarm. When the operating parameter rises above the value hereinafter, action associated with the alarm will be taken.
high_warning ——Specify the highest threshold for the warning. When the operating parameter rises above the value hereinafter, action associated with the warning will be taken.
268
low_alarm ——Specify the lowest threshold for the alarm. When the operating parameter falls below the value hereinafter, action associated with the alarm will be taken.
low_warning —— Specify the lowest threshold for the warning. When the operating parameter falls below the value hereinafter, action associated with the warning will be taken.
value —— Enter the threshold value in Volt.
Default Setting None.
Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface range gigabitEthernet)
Example Configure the high_alarm threshold of DDM voltage on the port 1/0/25 as 5:
T2600G-28TS(config)#interface gigabitEthernet 1/0/25
T2600G-28TS(config-if)#ddm voltage_threshold high_alarm 5
34.5 ddm bias_current_threshold Description
The ddm bias_current_threshold command is used to configure the threshold of the DDM Bias Current value.
Syntax ddm bias_current_threshold { high_alarm | high_warning | low_alarm | low_warning } value
Parameter high_alarm —— Specify the highest threshold for the alarm. When the operating parameter rises above the value hereinafter, action associated with the alarm will be taken.
high_warning ——Specify the highest threshold for the warning. When the operating parameter rises above the value hereinafter, action associated with the warning will be taken.
low_alarm ——Specify the lowest threshold for the alarm. When the operating parameter falls below the value hereinafter, action associated with the alarm will be taken.
269
low_warning —— Specify the lowest threshold for the warning. When the operating parameter falls below the value hereinafter, action associated with the warning will be taken.
value —— Enter the threshold value in mA.
Default Setting None.
Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface range gigabitEthernet)
Example Configure the high_alarm threshold of DDM Bias Current on the port 1/0/25 as 5:
T2600G-28TS(config)#interface gigabitEthernet 1/0/25
T2600G-28TS(config-if)#ddm bias_current_threshold high_alarm 5
34.6 ddm tx_power_threshold Description
The ddm tx_power_threshold command is used to configure the threshold of the DDM Tx Power value.
Syntax ddm tx_power_threshold { high_alarm | high_warning | low_alarm | low_warning } value
Parameter high_alarm —— Specify the highest threshold for the alarm. When the operating parameter rises above the value hereinafter, action associated with the alarm will be taken.
high_warning ——Specify the highest threshold for the warning. When the operating parameter rises above the value hereinafter, action associated with the warning will be taken.
low_alarm ——Specify the lowest threshold for the alarm. When the operating parameter falls below the value hereinafter, action associated with the alarm will be taken.
low_warning —— Specify the lowest threshold for the warning. When the operating parameter falls below the value hereinafter, action associated with the warning will be taken.
270
value —— Enter the threshold value in mW.
Default Setting None.
Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface range gigabitEthernet)
Example Configure the high_alarm threshold of DDM Tx Power on the port 1/0/25 as 5:
T2600G-28TS(config)#interface gigabitEthernet 1/0/25
T2600G-28TS(config-if)#ddm tx_power_threshold high_alarm 5
34.7 ddm rx_power_threshold Description
The ddm rx_power_threshold command is used to configure the threshold of the DDM Rx Power value.
Syntax ddm rx_power_threshold { high_alarm | high_warning | low_alarm | low_warning } value
Parameter high_alarm —— Specify the highest threshold for the alarm. When the operating parameter rises above the value hereinafter, action associated with the alarm will be taken.
high_warning ——Specify the highest threshold for the warning. When the operating parameter rises above the value hereinafter, action associated with the warning will be taken.
low_alarm ——Specify the lowest threshold for the alarm. When the operating parameter falls below the value hereinafter, action associated with the alarm will be taken.
low_warning —— Specify the lowest threshold for the warning. When the operating parameter falls below the value hereinafter, action associated with the warning will be taken.
value —— Enter the threshold value in mW.
Default Setting None.
271
Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface range gigabitEthernet)
Example Configure the high_alarm threshold of DDM Rx Power on the port 1/0/25 as 5:
T2600G-28TS(config)#interface gigabitEthernet 1/0/25
T2600G-28TS(config-if)#ddm rx_power_threshold high_alarm 5
34.8 show ddm configuration Description
The show ddm configuration command is used to display the DDM configuration.
Syntax show ddm configuration { state | temperature | voltage | bias_current | tx_power | rx_power }
Parameter state —— Display the DDM configuration state.
temperature —— Displays the threshold of the DDM temperature value.
voltage —— Displays the threshold of the DDM Voltage value.
bias_current —— Displays the threshold of the DDM Bias Current value.
tx_power —— Displays the threshold of the DDM Tx Power value.
rx_power —— Displays the threshold of the DDM Rx Power value.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Example View the DDM configuration state:
T2600G-28TS(config)#show ddm configuration state
View the threshold of the DDM Voltage value:
T2600G-28TS(config)#show ddm configuration voltage
272
34.9 show ddm status Description
The show ddm status command is used to display the DDM status, which is the digital diagnostic monitoring status of SFP modules inserting into the switch’s SFP ports.
Syntax show ddm status
Command Mode Privileged EXEC Mode and Any Configuration Mode
Example View the DDM status:
T2600G-28TS(config)#show ddm status
273
Chapter 35 ACL Commands
ACL (Access Control List) is used to filter data packets by configuring a series of match conditions, operations and time ranges. It provides a flexible and secured access control policy and facilitates you to control the network security.
35.1 time-range Description
The time-range command is used to add Time-Range. To delete the corresponding Time-Range, please use no time-range command. A time-range based ACL enables you to implement ACL control over packets by differentiating the time-ranges. A time-range can be specified in each rule in an ACL. The rule takes effect only when the specified time-range is configured and the system time is within the time-range.
Syntax time-range name
no time-range name
Parameter name —— The Time-Range name, ranging from 1 to 16 characters.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Add a time-range named tSeg1:
T2600G-28TS(config)# time-range tSeg1
35.2 absolute Description
The absolute command is used to configure a time-range into an absoluteness mode. To delete the corresponding Absoluteness Mode time-range, please use no absolute command.
274
Syntax absolute start start-date end end-date
no absolute
Parameter start-date —— The start date in Absoluteness Mode, in the format of MM/DD/YYYY. By default, it is 01/01/1970.
end-date —— The end date in Absoluteness Mode, in the format of MM/DD/YYYY. By default, it is 12/31/2099. The Absoluteness Mode will be disabled if the start date and end date are both in default value.
Command Mode Time-range Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the time-range tSeg1 with time from May 5, 2012 to Oct. 5, 2012:
T2600G-28TS(config)# time-range tSeg1
T2600G-28TS(config-time-range)# absolute start 05/05/2012 end
10/05/2012
35.3 periodic Description
The periodic command is used to configure the time-range into periodic mode. To delete the corresponding Periodic Mode time-range, please use no periodic command. To delete the corresponding Periodic Mode week-date time-range, please use no periodic week-date command. To delete the corresponding Periodic Mode time-slice time-range, please use no periodic time-slice command.
Syntax periodic [week-date week-day] [time-slice1 time-slice] [time-slice2 time-slice] [time-slice3 time-slice] [time-slice4 time-slice]
no periodic
no periodic week-date
no periodic time-slice
275
Parameter week-day —— Periodic Mode, in the format of 1-3,6 or daily, weekend, weekdays. 1-3, 6 represent Monday, Tuesday, Wednesday and Saturday; daily represents every day; weekend represents weekend and weekdays represents working day. By default, the Periodic Mode is disabled.
time-slice —— Create the time-slice, in the format of HH:MM-HH:MM.
Command Mode Time-range Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the time-range tSeg1 with time from 8:30 to 12:00 at weekend:
T2600G-28TS(config)#time-range tSeg1
T2600G-28TS(config-time-range)#periodic week-date weekend
time-slice1 08:30-12:00
35.4 holiday Description
The holiday command is used to configure the time-range into Holiday Mode under Time-range Create Configuration Mode. To delete the corresponding Holiday Mode time-range, please use no holiday command.
Syntax holiday
no holiday
Command Mode Time-range Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the time-range tSeg1 into Holiday Mode:
T2600G-28TS(config)#time-range tSeg1
276
T2600G-28TS(config-time-range)#holiday
35.5 holiday (global) Description
The holiday command is used to define a holiday. To delete the corresponding holiday, please use no holiday command.
Syntax holiday name start-date start-date end-date end-date
no holiday
Parameter name —— The holiday name, ranging from 1 to 16 characters.
start-date —— The start date of the holiday, in the format of MM/DD, for instance, 05/01.
end-date —— The end date of the holiday, in the format of MM/DD, for instance, 05/03.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Define National Day, configuring the start date as October 1st, and the end date as October 3rd:
T2600G-28TS(config)#holiday nationalday start-date 10/01 end-date
10/03
35.6 access-list create Description
The access-list create command is used to create Standard-IP ACL, Extend-IP ACL, Combined ACL, IPv6 ACL and Packet Content ACL.
Syntax access-list create access-list-num
277
Parameter access-list-num —— ACL ID, ranging from 0 to 4499. The ID range of the Standard-IP ACL is 500-1499, the Extend-IP ACL is 1500-2499, the Combined ACL is 2500-3499, the IPv6 ACL is 3500-4499 and the Packet Content ACL is 4500-4999.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Create a standard-IP ACL whose ID is 523:
T2600G-28TS(config)# access-list create 523
35.7 mac access-list Description
The mac access-list command is used to create MAC ACL. To set the detailed configurations for a specified MAC ACL, please use mac access-list command to access Mac Access-list Configuration Mode. To delete the MAC ACL, please use no mac access-list.
Syntax mac access-list access-list-num
no mac access-list access-list-num
Parameter access-list-num —— ACL ID, ranging from 0 to 499.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Create a MAC ACL whose ID is 423:
T2600G-28TS(config)# mac access-list 423
278
35.8 access-list standard Description
The access-list standard command is used to add Standard-IP ACL rule. To delete the corresponding rule, please use no access-list standard command. Standard-IP ACLs analyze and process data packets based on a series of match conditions, which can be the source IP addresses and destination IP addresses carried in the packets.
Syntax access-list standard acl-id rule rule-id { deny | permit } [[ sip source-ip ] smask source-ip-mask] [[ dip destination-ip ] dmask destination-ip-mask ] [ tseg time-segment ]
no access-list standard acl-id rule rule-id
Parameter acl-id —— The desired Standard-IP ACL for configuration.
rule-id —— The rule ID.
deny —— The operation to discard packets.
permit ——The operation to forward packets. It is the default value.
source-ip —— The source IP address contained in the rule.
source-ip-mask —— The source IP address mask. It is required if you typed the source IP address.
destination-ip —— The destination IP address contained in the rule.
destination-ip-mask —— The destination IP address mask. It is required if you typed the destination IP address.
time-segment —— The time-range for the rule to take effect. By default, it is not limited.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Create a Standard-IP ACL whose ID is 520, and add Rule 10 for it. In the rule, the source IP address is 192.168.0.100, the source IP address mask is
279
255.255.255.0, the time-range for the rule to take effect is “tRange1”, and the packets match this rule will be forwarded by the switch:
T2600G-28TS(config)# access-list create 520
T2600G-28TS(config)# access-list standard 520 rule 10 permit sip
192.168.0.100 smask 255.255.255.0 tseg tSeg1
35.9 access-list extended Description
The access-list extended command is used to add Extended-IP ACL rule. To delete the corresponding rule, please use no access-list extended command.
Syntax access-list extended acl-id rule rule-id { deny | permit } [[ sip source-ip ] smask source-ip-mask ] [[ dip destination-ip] dmask destination-ip-mask ] [ tseg time-segment ] [frag {disable | enable}] [ dscp dscp ] [ s-port s-port ] [ d-port d-port ] [ tcpflag tcpflag ] [ protocol protocol ] [ tos tos ] [ pre pre ]
no access-list extended acl-id rule rule-id
Parameter acl-id——The desired Extended-IP ACL for configuration.
rule-id —— The rule ID.
deny —— The operation to discard packets.
permit ——The operation to forward packets. It is the default value.
source-ip —— The source IP address contained in the rule.
source-ip-mask —— The source IP address mask. It is required if you typed the source IP address.
destination-ip —— The destination IP address contained in the rule.
destination-ip-mask —— The destination IP address mask. It is required if you typed the destination IP address.
time-segment —— The time-range for the rule to take effect. By default, it is not limited.
frag —— Enable/Disable Fragment. By default, it is disabled. If Fragment is enabled, this rule will process all the fragments and the last piece of fragment will be always forwarded.
dscp —— Specify the dscp value, ranging from 0 to 63.
280
s-port —— The source port number.
d-port —— The destination port number.
tcpflag —— Specify the flag value when using TCP protocol.
protocol —— Configure the value of the matching protocol.
tos —— Enter the IP ToS contained in the rule.
pre —— Enter the IP Precedence contained in the rule.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Create an Extended-IP ACL whose ID is 2220, and add Rule 10 for it. In the rule, the source IP address is 192.168.0.100, the source IP address mask is 255.255.255.0, the time-range for the rule to take effect is tSeg1, and the packets match this rule will be forwarded by the switch:
T2600G-28TS(config)# access-list create 2220
T2600G-28TS(config)# access-list extended 2220 rule 10 permit sip
192.168.0.100 smask 255.255.255.0 tseg tSeg1
35.10 access-list combined Description
The access-list combined command is used to add Combined ACL rule. To delete the corresponding rule, please use no access-list combined command. Combined ACLs analyze and process data packets based on a series of match conditions.
Syntax access-list combined acl-id rule rule-id { deny | permit } [ [ smac source-mac ] smask source-mac-mask ] [ [ dmac destination-mac ] dmask destination-mac-mask ] [ vid vlan-id ] [ type ethernet-type ] [ pri user-pri ] [ [ sip source-ip ] sip-mask source-ip-mask ] [ [ dip destination-ip ] dip-mask destination-ip-mask ] [ tseg time-segment ]
no access-list combined acl-id rule rule-id
281
Parameter acl-id —— The desired Standard-IP ACL for configuration.
rule-id —— The rule ID.
deny —— The operation to discard packets.
permit ——The operation to forward packets. It is the default value.
source-mac —— The source MAC address contained in the rule.
source-mac-mask —— The source MAC address mask. It is required if you typed the source MAC address.
destination-mac —— The destination MAC address contained in the rule.
destination-mac-mask —— The destination MAC address mask. It is required if you typed the destination MAC address.
vlan-id —— The VLAN ID contained in the rule, ranging from 1 to 4094.
ethernet-type —— EtherType contained in the rule, in the format of 4-hex number.
user-pri —— The user priority contained in the rule, ranging from 0 to 7. By default, it is not limited.
time-segment —— The time-range for the rule to take effect. By default, it is not limited.
source-ip —— The source IP address contained in the rule.
source-ip-mask —— The source IP address mask. It is required if you typed the source IP address.
destination-ip —— The destination IP address contained in the rule.
destination-ip-mask —— The destination IP address mask. It is required if you typed the destination IP address.
time-segment —— The time-range for the rule to take effect. By default, it is not limited.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines Before binding a Combined ACL to a VLAN or interface, you should configure the SDM template as “default” or “enterpriseV4” and save your configurations. For more information about SDM configuration, please refer to sdm prefer.
282
Example Create a Combined ACL whose ID is 2700, and add Rule 10 for it. In the rule, the source MAC address is 00:01:3F:48:16:23, the source MAC address mask is 11:11:11:11:11:00, the source IP address is 192.168.0.100, the source IP address mask is 255.255.255.0, the time-range for the rule to take effect is “tSeg1”, and the packets match this rule will be forwarded by the switch:
T2600G-28TS(config)# access-list create 2700
T2600G-28TS(config)# access-list combined 2700 rule 10 permit smac
00:01:3F:48:16:23 smask 11:11:11:11:11:00 sip 192.168.0.100 sip-mask
255.255.255.0 tseg tSeg1
35.11 access-list ipv6 Description
The access-list ipv6 command is used to add IPv6 ACL rule. To delete the corresponding rule, please use no access-list ipv6 command. Standard-IP ACLs analyze and process data packets based on a series of match conditions, which can be the source IP addresses and destination IP addresses carried in the packets, the DSCP and flow-label value, etc.
Syntax access-list ipv6 acl-id rule rule-id { deny | permit } [dscp dscp-value] [flow-label flow-label-value] [ [ sip source-ip ] sip-mask source-ip-mask] [ [ dip destination-ip ] dip-mask destination-ip-mask ] [ s-port s-port ] [ d-port d-port ] [ tseg time-segment ]
no access-list ipv6 acl-id rule rule-id
Parameter acl-id —— The desired Standard-IP ACL for configuration.
rule-id —— The rule ID.
deny —— The operation to discard packets.
permit ——The operation to forward packets. It is the default value.
dscp-value —— Specify the dscp value, ranging from 0 to 63.
flow-label-value —— The IPv6 flow label, which ranges from 0-0xfffff.
source-ip —— The source IP address contained in the rule.
source-ip-mask —— The source IP address mask. It is required if you typed the source IP address.
283
destination-ip —— The destination IP address contained in the rule.
destination-ip-mask —— The destination IP address mask. It is required if you typed the destination IP address.
s-port —— The source port number.
d-port —— The destination port number.
(Note: T2600G-18TS doesn’t support s-port and d-port setting.)
time-segment —— The time-range for the rule to take effect. By default, it is not limited.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines Before binding an IPv6 ACL to a VLAN or interface, you should configure the SDM template as “enterpriseV6” and save your configurations. For more information about SDM configuration, please refer to sdm prefer.
Example Create an IPv6 ACL whose ID is 3600, and add Rule 10 for it. In the rule, the source IP address is 3001::1, the source IP address mask is 255.255.255.0, the time-range for the rule to take effect is “tSeg1”, and the packets match this rule will be forwarded by the switch:
T2600G-28TS(config)# access-list create 3600
T2600G-28TS(config)# access-list ipv6 3600 rule 10 permit sip 3001::1
sip-mask ffff:ffff:ff00:00ff tseg tSeg1
35.12 rule Description
The rule command is used to configure MAC ACL rule. To delete the corresponding rule, please use no rule command.
Syntax rule rule-id { deny | permit } [[ smac source-mac ] smask source-mac-mask ] [[ dmac destination-mac ] dmask destination-mac-mask ] [ vid vlan-id ] [ type ethernet-type ] [ pri user-pri ] [ tseg time-segment ]
284
no rule rule-id
Parameter rule-id —— The rule ID.
deny —— The operation to discard packets.
permit ——The operation to forward packets. It is the default value.
source-mac —— The source MAC address contained in the rule.
source-mac-mask —— The source MAC address mask. It is required if you typed the source MAC address.
destination-mac —— The destination MAC address contained in the rule.
destination-mac-mask —— The destination MAC address mask. It is required if you typed the destination MAC address.
vlan-id —— The VLAN ID contained in the rule, ranging from 1 to 4094.
ethernet-type —— EtherType contained in the rule, in the format of 4-hex number.
user-pri —— The user priority contained in the rule, ranging from 0 to 7. By default, it is not limited.
time-segment —— The time-range for the rule to take effect. By default, it is not limited.
Command Mode MAC Access-list Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Create a MAC ACL whose ID is 20, and add Rule 10 for it. In the rule, the source MAC address is 00:01:3F:48:16:23, the source MAC address mask is 11:11:11:11:11:00, VLAN ID is 2, the user priority is 5, the time-range for the rule to take effect is “tRange1”, and the packets match this rule will be forwarded by the switch:
T2600G-28TS(config)# mac access-list 20
T2600G-28TS(config-mac-acl)# rule 10 permit smac 00:01:3F:48:16:23
smask 11:11:11:11:11:00 vid 2 pri 5 tseg tRange1
285
35.13 access-list policy name Description
The access-list policy name command is used to add Policy. To delete the corresponding Policy, please use no access-list policy name command. A Policy is used to control the data packets those match the corresponding ACL rules by configuring ACLs and actions together for effect. The operations here include stream mirror, stream condition, QoS Remarking and redirect.
Syntax access-list policy name name
no access-list policy name name
Parameter name —— The Policy Name, ranging from 1 to 16 characters.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Add a Policy named policy1:
T2600G-28TS(config)# access-list policy name policy1
35.14 access-list policy action Description
The access-list policy action command is used to add ACLs and create actions for the policy. To set the detailed configuration of actions for a policy, please use access-list policy action command to access Action Configuration Mode. To delete the corresponding actions, please use no access-list policy action command.
Syntax access-list policy action policy-name acl-id
no access-list policy action policy-name acl-id
286
Parameter policy-name —— The Policy Name, ranging from 1 to 16 characters.
acl-id —— The ID of the ACL to which the above policy is applied.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Add ACL whose ID is 120 to policy1 and create an action for them:
T2600G-28TS(config)# access-list policy action policy1 120
35.15 redirect interface Description
The redirect interface command is used to configure Direction function of policy action for specified ports.
Syntax redirect interface { gigabitEthernet port }
Parameter port —— The Destination Port of Redirect. The data packets matching the corresponding ACL will be forwarded to the specific port. By default, it is All Ports.
Command Mode Action Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Edit the actions for policy1. Forward the data packets matching ACL 120 in the policy to Gigabit Ethernet port 2:
T2600G-28TS(config)#access-list policy action policy1 120
T2600G-28TS(config-action)#redirect interface gigabitEthernet 1/0/2
287
35.16 s-condition Description
The s-condition command is used to configure Stream Condition function of policy action.
Syntax s-condition rate rate osd { none | discard }
Parameter rate —— The rate of Stream Condition, ranging from 0 to 1000000kbps.
osd —— Out of Band disposal of Stream Condition. It is the disposal way of the data packets those are transmitted beyond the rate. There are two options, “none” and “discard”. By default, the option is “none”.
Command Mode Action Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Edit the actions for policy1. For the data packets matching ACL 120 in the policy, if the rate beyond 1000kbps, they will be discarded by the switch:
T2600G-28TS(config)#access-list policy action policy1 120
T2600G-28TS(config-action)#s-condition rate 1000 osd discard
35.17 s-mirror Description
The s-mirror command is used to configure Stream Mirror function of policy action to the specified port.
Syntax s-mirror interface { gigabitEthernet port }
Parameter port —— The Mirror Port number of Stream Mirror.
Command Mode Action Configuration Mode
288
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Edit the actions for policy1. Specify the mirror port as Gigabit Ethernet port 1/0/2 for the data packets matching ACL 120:
T2600G-28TS(config)#access-list policy action policy1 120
T2600G-28TS(config-action)#s-mirror interface gigabitEthernet 1/0/2
35.18 qos-remark Description
The qos-remark command is used to configure QoS Remark function of policy action.
Syntax qos-remark [ dscp dscp ] [ priority pri ] [dot1p dot1p-pri]
no qos-remark
Parameter dscp —— DSCP of QoS Remark. Specify the DSCP region for the data packets matching the corresponding ACL. DSCP ranges from 0 to 63. By default, it is not limited.
pri —— Local Priority of QoS Remark. Specify the local priority for the data packets matching the corresponding ACL. Local Priority ranges from 0 to 7.
dot1p-pri —— 802.1P priority of QoS Remark. This remark configuration will change the data packet's 802.1P priority field to the dot1p-pri you set. 802.1P priority ranges from 0 to 7.
Command Mode Action Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Edit the actions for policy1. For the data packets matching ACL 120, specify the DSCP region as 30 and local priority 2:
T2600G-28TS(config)#access-list policy action policy1 120
289
T2600G-28TS(config-action)# qos-remark dscp 30 priority 2
35.19 access-list bind acl (interface) Description
The access-list bind acl command is used to bind an ACL to the specified port. To cancel the bind relation, please use no access-list bind acl command.
Syntax access-list bind acl acl-id
no access-list bind acl acl-id
Parameter acl-id —— The ID of the ACL desired to bind.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Bind ACL 100 to port 1/0/2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# access-list bind acl 100
35.20 access-list bind acl (vlan)
Note: Packet content ACL doesn’t support VLAN bind.
Description The access-list bind acl command is used to bind an ACL to the specified VLAN. To cancel the bind relation, please use no access-list bind acl command.
Syntax access-list bind acl acl-id
no access-list bind acl acl-id
290
Parameter acl-id —— The ID of the ACL desired to bind.
Command Mode Interface VLAN Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Bind ACL 100 to VLAN 2:
T2600G-28TS(config)# interface vlan 2
T2600G-28TS(config-if)# access-list bind acl 100
35.21 access-list bind (interface) Description
The access-list bind command is used to bind a policy to a specified port. To cancel the bind relation, please use no access-list bind command.
Syntax access-list bind policy-name
no access-list bind policy-name
Parameter policy-name —— The name of the policy desired to bind.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Bind policy1 to port 1/0/2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# access-list bind policy1
291
35.22 access-list packet-content profile
Note: T2600G-18TS doesn’t support this command.
Description The access-list packet-content profile command is used to configure packet-content ACL chunk offset profile. There are four chunks to be configured. They must be configured before you configure the chunk value&mask. The offset value ranges from 0 to 31. Offset 31 matches the 1,2,127,128 bytes of the packet, offset 0 matches the 3,4,5,6 bytes of the packet, offset 1 matches the 7,8,9,10 bytes of the packet, and so on, for the rest of the offset value.
Syntax access-list packet-content profile chunk-offset0 offset0 chunk-offset1 offset1 chunk-offset2 offset2 chunk-offset3 offset3
Parameter offset —— The offset value, ranging from 0 to 31.
Command mode Global Configuration Mode
Privilege Requirement Only Admin, Operator and Power User level users have access to these commands.
Example Configure a packet content profile with offset 0,1,2,3:
T2600-28TS(config)# access-list packet-content profile chunk-offset0 0
chunk-offset1 1 chunk-offset2 2 chunk-offset3 3
35.23 access-list packet-content config
Note: T2600G-18TS doesn’t support this command.
Description The access-list packet-content config command is used to add Packet Content ACL rule. To delete the corresponding rule, please use no access-list packet-content config command. Packet content ACLs analyze and process data packets based on 4 chunk match conditions, each chunk
292
can specify a user-defined 4-byte segment carried in the packet's first 128 bytes.
Syntax access-list packet-content config acl-id rule rule-id {deny | permit} [chunk0 value mask0 mask] [chunk1 value mask1 mask] [chunk2 value mask2 mask] [chunk3 value mask3 mask] [tseg time-segment]
Parameter acl-id —— The desired Standard-IP ACL for configuration.
rule-id —— The rule ID.
deny —— The operation to discard packets.
permit ——The operation to forward packets. It is the default value.
value—— Specify the chunk value, ranging from 0-ffffffff.
Mask ——Specify the chunk mask, ranging from 0-ffffffff. Chunk mask here must be written completely in 4-byte hex mode, like '0000ffff'.
time-segment —— The time-range for the rule to take effect. By default, it is not limited.
Command mode Global Configuration Mode
Privilege Requirement Only Admin, Operator and Power User level users have access to these commands.
Example Create a packet-content acl rule with all 4 chunks configured, the rule id is 1 and the default action is permit:
T2600-28TS(config)# access-list packet-content config rule 1 permit
chunk0 45ea mask0 0000ffff chunk1 1111ffff mask1 ffffffff chunk2 ee34
mask2 ffff0000 chunk3 7878 mask3 000ffae3
T2600-28TS(config)# access-list packet-content profile chunk-offset0 0
chunk-offset1 1 chunk-offset2 2 chunk-offset3 3
35.24 access-list bind (vlan)
Note: Packet content ACL doesn’t support VLAN bind.
293
Description The access-list bind command is used to bind a policy to a VLAN. To cancel the bind relation, please use no access-list bind command.
Syntax access-list bind policy-name
no access-list bind policy-name
Parameter policy-name —— The name of the policy desired to bind.
Command Mode Interface VLAN Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Bind policy1 to VLAN 2:
T2600G-28TS(config)# interface vlan 2
T2600G-28TS(config-if)# access-list bind policy1
35.25 show access-list Description
The show access-list command is used to display configuration of ACL.
Syntax show access-list acl-id
Parameter acl-id —— The ID of the ACL selected to display the configuration.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the configuration of the MAC ACL whose ID is 20:
T2600G-28TS(config)# show access-list 20
294
35.26 show access-list status Description
The show access-list status command is used to display the status of ACL hardware entry table. Here you can view the total number and available number of the ACL entries.
Syntax show access-list status
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the status of ACL hardware entry table:
T2600G-28TS(config)# show access-list status
35.27 show access-list policy Description
The show access-list policy command is used to display the information of a specified policy.
Syntax show access-list policy name
Parameter name —— The Policy Name desired to show.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the information of a policy named policy1:
T2600G-28TS(config)# show access-list policy policy1
295
35.28 show access-list bind Description
The show access-list bind command is used to display the configuration of Policy bind.
Syntax show access-list bind
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the configuration of Policy bind:
T2600G-28TS(config)# show access-list bind
296
Chapter 36 MSTP Commands
MSTP (Multiple Spanning Tree Protocol), compatible with both STP and RSTP and subject to IEEE 802.1s, can disbranch a ring network. STP is to block redundant links and backup links as well as optimize paths.
36.1 debug spanning-tree Description
The debug spanning-tree command is used to enable debuggning of spanning-tree activities. To disable the debugging function, please use no debug spanning-tree command.
Syntax debug spanning-tree { all | bpdu receive | bpdu transmit | cmpmsg | errors | flush | init | migration | proposals | roles | state | tc }
no debug spanning-tree { all | bpdu receive | bpdu transmit | cmpmsg | errors | flush | init | migration | proposals | roles | state | tc }
Parameters all —— Display all the spanning-tree debug messages.
bpdu receive —— Display the debug messages of the received spanning-tree bridge protocol data unit (BPDU).
bpdu transmit —— Display the debug messages of the sent spanning-tree BPDU.
cmpmsg —— Display the message priority debug messages.
errors —— Display the MSTP error debug messages.
flush —— Display the address table flushing debug messages.
init —— Display the data structure initialization debug messages.
migration —— Display the version migration debug messages.
proposals —— Display the MSTP handshake debug messages.
roles —— Display the MSTP interface role switchling debug messages.
state —— Display the MSTP interface state change debug messages.
tc —— Display the MSTP topology event debug messages.
Command Mode Privileged EXEC Mode
297
Privilege Requirement
Only Admin level users have access to these commands.
Example Display all the spanning-tree debug messages:
T2600G-28TS# debug spanning-tree all
36.2 spanning-tree (global) Description
The spanning-tree command is used to enable STP function globally. To disable the STP function, please use no spanning-tree command.
Syntax spanning-tree
no spanning-tree
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the STP function:
T2600G-28TS(config)# spanning-tree
36.3 spanning-tree (interface) Description
The spanning-tree command is used to enable STP function for a port. To disable the STP function, please use no spanning-tree command.
Syntax spanning-tree
no spanning-tree
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
298
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the STP function for port 1/0/2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# spanning-tree
36.4 spanning-tree common-config Description
The spanning-tree common-config command is used to configure the parameters of the ports for comparison in the CIST and the common parameters of all instances. To return to the default configuration, please use no spanning-tree common-config command. CIST (Common and Internal Spanning Tree) is the spanning tree in a switched network, connecting all devices in the network.
Syntax spanning-tree common-config [ port-priority pri ] [ ext-cost ext-cost ] [ int-cost int-cost ] [ portfast { enable | disable }] [ point-to-point { auto | open | close }]
no spanning-tree common-config
Parameter pri —— Port Priority, which must be multiple of 16 ranging from 0 to 240. By default, the port priority is 128. Port Priority is an important criterion on determining if the port connected to this port will be chosen as the root port. In the same condition, the port with the highest priority will be chosen as the root port. The lower value has the higher priority.
ext-cost —— External Path Cost, which is used to choose the path and calculate the path costs of ports in different MST regions. It is an important criterion on determining the root port. The lower value has the higher priority. It ranges from o to 2000000. By default, it is 0 which is mean auto.
int-cost —— Internal Path Cost, which is used to choose the path and calculate the path costs of ports in an MST region. It is an important criterion on determining the root port. The lower value has the higher priority. By
299
default, it is automatic. It ranges from o to 2000000. By default, it is 0 which is mean auto.
portfast —— Enable/ Disable Edge Port. By default, it is disabled. The edge port can transit its state from blocking to forwarding rapidly without waiting for forward delay.
point-to-point —— The P2P link status, with auto, open and close options. By default, the option is auto. If the two ports in the P2P link are root port or designated port, they can transit their states to forwarding rapidly to reduce the unnecessary forward delay.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the STP function of port 1, and configure the Port Priority as 64, ExtPath Cost as 100, IntPath Cost as 100, and then enable Edge Port:
T2600G-28TS(config)# interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)# spanning-tree common-config port-priority 64
ext-cost 100 int-cost 100 portfast enable point-to-point open
36.5 spanning-tree mode Description
The spanning-tree mode command is used to configure the STP mode of the switch. To return to the default configurations, please use no spanning-tree mode command.
Syntax spanning-tree mode { stp | rstp | mstp }
no spanning-tree mode
Parameter stp ——Spanning Tree Protocol, the default value.
rstp ——Rapid Spanning Tree Protocol
mstp ——Multiple Spanning Tree Protocol
300
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the spanning-tree mode as mstp:
T2600G-28TS(config)# spanning-tree mode mstp
36.6 spanning-tree mst configuration Description
The spanning-tree mst configuration command is used to access MST Configuration Mode from Global Configuration Mode, as to configure the VLAN-Instance mapping, region name and revision level. To return to the default configuration of the corresponding Instance, please use no spanning-tree mst configuration command.
Syntax spanning-tree mst configuration
no spanning-tree mst configuration
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enter into the MST configuration mode:
T2600G-28TS(config)# spanning-tree mst configuration
T2600G-28TS(Config-mst)#
36.7 instance Description
The instance command is used to configure the VLAN-Instance mapping. To remove the VLAN-instance mapping or disable the corresponding instance,
301
please use no instance command. When an instance is disabled, the related mapping VLANs will be removed.
Syntax instance instance-id vlan vlan-id
no instance instance-id [ vlan vlan-id ]
Parameters instance-id —— Instance ID, ranging from 1 to 8.
vlan-id —— The VLAN ID selected to mapping with the corresponding instance.
Command Mode MST Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Map the VLANs 1-100 to Instance 1:
T2600G-28TS(config)# spanning-tree mst configuration
T2600G-28TS(config-mst)# instance 1 vlan 1-100
Disable Instance 1, namely remove all the mapping VLANs 1-100:
T2600G-28TS(config)# spanning-tree mst configuration
T2600G-28TS(config-mst)# no instance 1
Remove VLANs 1-50 in mapping VLANs 1-100 for Instance 1:
T2600G-28TS(config)# spanning-tree mst configuration
T2600G-28TS(config-mst)# no instance 1 vlan 1-50
36.8 name Description
The name command is used to configure the region name of MST instance.
Syntax name name
302
Parameters name —— The region name, used to identify MST region. It ranges from 1 to 32 characters.
Command Mode MST Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the region name of MST as “region1”:
T2600G-28TS(config)# spanning-tree mst configuration
T2600G-28TS(config-mst)# name region1
36.9 revision Description
The revision command is used to configure the revision level of MST instance.
Syntax revision revision
Parameters revision —— The revision level for MST region identification, ranging from 0 to 65535.
Command Mode MST Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the revision level of MST as 100:
T2600G-28TS(config)# spanning-tree mst configuration
T2600G-28TS(config-mst)# revision 100
303
36.10 spanning-tree mst instance Description
The spanning-tree mst instance command is used to configure the priority of MST instance. To return to the default value of MST instance priority, please use no spanning-tree mst instance command.
Syntax spanning-tree mst instance instance-id priority pri
no spanning-tree mst instance instance-id priority
Parameter instance-id —— Instance ID, ranging from 1 to 8.
pri —— MSTI Priority, which must be multiple of 4096 ranging from 0 to 61440. By default, it is 32768. MSTI priority is an important criterion on determining if the switch will be chosen as the root bridge in the specific instance.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the MST Instance 1 and configure its priority as 4096:
T2600G-28TS(config)# spanning-tree mst instance 1 priority 4096
36.11 spanning-tree mst Description
The spanning-tree mst command is used to configure MST Instance Port. To return to the default configuration of the corresponding Instance Port, please use no spanning-tree mst command. A port can play different roles in different spanning tree instance. You can use this command to configure the parameters of the ports in different instance IDs as well as view status of the ports in the specified instance.
Syntax spanning-tree mst instance instance-id {[ port-priority pri ] | [ cost cost ]}
304
no spanning-tree mst instance instance-id
Parameter instance-id —— Instance ID, ranging from 1 to 8.
pri —— Port Priority, which must be multiple of 16 ranging from 0 to 240. By default, it is 128. Port Priority is an important criterion on determining if the port will be chosen as the root port by the device connected to this port.
cost —— Path Cost, ranging from 0 to 200000. The lower value has the higher priority. Its default value is 0 meaning “auto”.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the priority of port 1 in MST Instance 1 as 64, and path cost as 2000:
T2600G-28TS(config)# interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)# spanning-tree mst instance 1 port-priority 64
cost 2000
36.12 spanning-tree priority Description
The spanning-tree priority command is used to configure the bridge priority. To return to the default value of bridge priority, please use no spanning-tree priority command.
Syntax spanning-tree priority pri
no spanning-tree priority
Parameter pri —— Bridge priority, ranging from 0 to 61440. It is 32768 by default.
Command Mode Global Configuration Mode
305
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the bridge priority as 4096:
T2600G-28TS(config)# spanning-tree priority 4096
36.13 spanning-tree timer Description
The spanning-tree timer command is used to configure forward-time, hello-time and max-age of Spanning Tree. To return to the default configurations, please use no spanning-tree timer command.
Syntax spanning-tree timer {[ forward-time forward-time ] [ hello-time hello-time ] [ max-age max-age ]}
no spanning-tree timer
Parameter forward-time —— Forward Delay, which is the time for the port to transit its state after the network topology is changed. Forward Delay ranges from 4 to 30 in seconds and it is 15 by default. Otherwise, 2 * (Forward Delay - 1) >= Max Age.
hello-time ——Hello Time, which is the interval to send BPDU packets, and used to test the links. Hello Time ranges from 1 to 10 in seconds and it is 2 by default. Otherwise, 2 * (Hello Time + 1) <= Max Age.
max-age —— The maximum time the switch can wait without receiving a BPDU before attempting to reconfigure, ranging from 6 to 40 in seconds. By default, it is 20.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure forward-time, hello-time and max-age for Spanning Tree as 16 seconds, 3 seconds and 22 seconds respectively:
306
T2600G-28TS(config)# spanning-tree timer forward-time 16 hello-time 3
max-age 22
36.14 spanning-tree hold-count Description
The spanning-tree hold-count command is used to configure the maximum number of BPDU packets transmitted per Hello Time interval. To return to the default configurations, please use no spanning-tree hold-count command.
Syntax spanning-tree hold-count value
no spanning-tree hold-count
Parameter value —— The maximum number of BPDU packets transmitted per Hello Time interval, ranging from 1 to 20 in pps. By default, it is 5.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the hold-count of STP as 8pps:
T2600G-28TS(config)# spanning-tree hold-count 8
36.15 spanning-tree max-hops Description
The spanning-tree max-hops command is used to configure the maximum number of hops that occur in a specific region before the BPDU is discarded. To return to the default configurations, please use no spanning-tree max-hops command.
Syntax spanning-tree max-hops value
no spanning-tree max-hops
307
Parameter value —— The maximum number of hops that occur in a specific region before the BPDU is discarded, ranging from 1 to 40 in hop. By default, it is 20.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the max-hops of STP as 30:
T2600G-28TS(config)# spanning-tree max-hops 30
36.16 spanning-tree bpdufilter Description
The spanning-tree bpdufilter command is used to enable the BPDU filter function for a port. With the function enabled, the port can be prevented from receiving and sending any BPDU packets. To disable the BPDU filter function, please use no spanning-tree bpdufilter command.
Syntax spanning-tree bpdufilter
no spanning-tree bpdufilter
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the BPDU filter function for port 1/0/2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# spanning-tree bpdufilter
308
36.17 spanning-tree bpduguard Description
The spanning-tree bpduguard command is used to enable the BPDU protect function for a port. With the BPDU protect function enabled, the port will set itself automatically as ERROR-PORT when it receives BPDU packets, and the port will disable the forwarding function for a while. To disable the BPDU protect function, please use no spanning-tree bpduguard command.
Syntax spanning-tree bpduguard
no spanning-tree bpduguard
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the BPDU protect function for port 1/0/2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# spanning-tree bpduguard
36.18 spanning-tree guard loop Description
The spanning-tree guard loop command is used to enable the Loop Protect function for a port. Loop Protect is to prevent the loops in the network brought by recalculating STP because of link failures and network congestions. To disable the Loop Protect function, please use no spanning-tree guard loop command.
Syntax spanning-tree guard loop
no spanning-tree guard loop
309
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the Loop Protect function for port 2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# spanning-tree guard loop
36.19 spanning-tree guard root Description
The spanning-tree guard root command is used to enable the Root Protect function for a port. With the Root Protect function enabled, the root bridge will set itself automatically as ERROR-PORT when receiving BPDU packets with higher priority, in order to maintain the role of root ridge. To disable the Root Protect function, please use no spanning-tree guard root command.
Syntax spanning-tree guard root
no spanning-tree guard root
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the Root Protect function for port 2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# spanning-tree guard root
310
36.20 spanning-tree guard tc Description
The spanning-tree guard tc command is used to enable the TC Protect of Spanning Tree function for a port. To disable the TC Protect of Spanning Tree function, please use no spanning-tree guard tc command. A switch removes MAC address entries upon receiving TC-BPDUs. If a malicious user continuously sends TC-BPDUs to a switch, the switch will be busy with removing MAC address entries, which may decrease the performance and stability of the network. With the Protect of Spanning Tree function enabled, you can configure the number of TC-BPDUs in a required time, so as to avoid the process of removing MAC addresses frequently.
Syntax spanning-tree guard tc
no spanning-tree guard tc
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the TC Protect of Spanning Tree for port 2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# spanning-tree guard tc
36.21 spanning-tree mcheck Description
The spanning-tree mcheck command is used to enable mcheck.
Syntax spanning-tree mcheck
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
311
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable mcheck for port 2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# spanning-tree mcheck
36.22 show spanning-tree active Description
The show spanning-tree active command is used to display the active information of spanning-tree.
Syntax show spanning-tree active
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the active information of spanning-tree:
T2600G-28TS(config)# show spanning-tree active
36.23 show spanning-tree bridge Description
The show spanning-tree bridge command is used to display the bridge parameters.
Syntax show spanning-tree bridge [ forward-time | hello-time | hold-count | max-age | max-hops | mode | priority | state ]
Command Mode Privileged EXEC Mode and Any Configuration Mode
312
Privilege Requirement
None.
Example Display the bridge parameters:
T2600G-28TS(config)# show spanning-tree bridge
36.24 show spanning-tree interface Description
The show spanning-tree interface command is used to display the spanning-tree information of all ports or a specified port.
Syntax show spanning-tree interface [ gigabitEthernet port | port-channel port-channel-id ] [ edge | ext-cost | int-cost | mode | p2p | priority | role | state | status ]
Parameter port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the spanning-tree information of all ports:
T2600G-28TS(config)# show spanning-tree interface
Display the spanning-tree information of port 1/0/2:
T2600G-28TS(config)# show spanning-tree interface gigabitEthernet
1/0/2
Display the spanning-tree mode information of port 1/0/2:
T2600G-28TS(config)# show spanning-tree interface gigabitEthernet
1/0/2 mode
313
36.25 show spanning-tree interface-security Description
The show spanning-tree interface-security command is used to display the protect information of all ports or a specified port.
Syntax show spanning-tree interface-security [ gigabitEthernet port | port-channel port-channel-id ] [ bpdufilter | bpduguard | loop | root | tc | tc-defend ]
Parameter port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the protect information of all ports:
T2600G-28TS(config)# show spanning-tree interface-security
Display the protect information of port 1:
T2600G-28TS(config)# show spanning-tree interface-security
gigabitEthernet 1/0/1
Display the interface security bpdufilter information:
T2600G-28TS(config)# show spanning-tree interface-security bpdufilter
36.26 show spanning-tree mst Description
The show spanning-tree mst command is used to display the related information of MST Instance.
Syntax show spanning-tree mst { configuration [ digest ] | instance instance-id [ interface [ gigabitEthernet port | port-channel port-channel-id ] ] }
314
Parameter instance-id —— Instance ID desired to show, ranging from 1 to 8.
port —— The Ethernet port number.
port-channel-id —— The ID of the port channel.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the region information and mapping information of VLAN and MST Instance:
T2600G-28TS(config)#show spanning-tree mst configuration
Display the related information of MST Instance 1:
T2600G-28TS(config)#show spanning-tree mst instance 1
Display all the ports information of MST Instance 1:
T2600G-28TS(config)#show spanning-tree mst instance 1 interface
315
Chapter 37 Ethernet OAM Commands
Ethernet OAM (standing for Operation, Administration, and Maintenance) is Layer 2 protocol that is used for monitoring and troubleshooting Ethernet networks. It can report the network status to network administrators through the OAMPDUs exchanged between two OAM entities. The operation of OAM on an Ethernet interface does not adversely affect data traffic as OAM is a slow protocol with very limited bandwidth potential.
37.1 ethernet-oam
Description
The ethernet-oam command is used to enable the Ethernet OAM function for the desired port. To disable the Ethernet OAM function, please use no ethernet-oam command.
Syntax
ethernet-oam
no ethernet-oam
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Enable the Ethernet OAM function for Gigabit Ethernet port 1/0/2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)#ethernet-oam
37.2 ethernet-oam mode
Description
The ethernet-oam mode command is used to configure the OAM mode for the desired port. To return to the default configurations, please use no ethernet-oam mode command. The default mode is active.
316
Syntax
ethernet-oam mode { passive | active }
no ethernet-oam mode
Parameter
passive —— Specify the OAM mode as passive.
active ——Specify the OAM mode as active.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure Ethernet OAM client to operate in passive mode for Gigabit Ethernet port 2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)#ethernet-oam mode passive
37.3 ethernet-oam link-monitor symbol-period
Description
The ethernet-oam link-monitor symbol-period command is used to configure the parameters about one of the link events, error symbol period event. To return to the default configurations, please use no ethernet-oam link-monitor symbol-period command.
Syntax
ethernet-oam link-monitor symbol-period { threshold threshold | window window | notify { disable | enable }}
no ethernet-oam link-monitor symbol-period { threshold | window | notify }
Parameter
threshold —— Configure the error threshold for generating error symbol-period event. The range is from 1 to 4294967295 and the default value is 1.
317
window —— Configure the error symbol-period event detection interval. The range is from 10 to 600, in terms of 100 ms intervals. The default value is 10.
notify —— Enable/Disable the event notification. By default, it is enabled.
threshold | window | notify —— The parameter that you want to return to the default configuration.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
For error symbol-period event, configure the error threshold as 5 and the event detection interval as 3 seconds on Gigabit Ethernet port 1/0/2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# ethernet-oam link-monitor symbol-period
threshold 5 window 30
37.4 ethernet-oam link-monitor frame
Description
The ethernet-oam link-monitor frame command is used to configure the parameters about one of the link events, error frame event. To return to the default configurations, please use no ethernet-oam link-monitor frame command.
Syntax
ethernet-oam link-monitor frame { [threshold threshold ] [ window window ] [notify { disable | enable } ] }
no ethernet-oam link-monitor frame { threshold | window | notify }
Parameter
threshold —— Configure the error threshold for generating error frame event. The range is from 1 to 4294967295 and the default value is 1.
window —— Configure the error symbol-period event detection interval. The range is from 10 to 600, in terms of 100 ms intervals. The default value is 10.
318
notify —— Enable/Disable the event notification. By default, it is enabled.
threshold | window | notify —— The parameter that you want to return to the default configuration.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
For error frame event, configure the error threshold as 6 and the event detection interval as 9 seconds on Gigabit Ethernet port 1/0/3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# ethernet-oam link-monitor frame threshold 6
window 90
37.5 ethernet-oam link-monitor frame-period
Description
The ethernet-oam link-monitor frame-period command is used to configure the parameters about one of the link events, error frame period event. To return to the default configurations, please use no ethernet-oam link-monitor frame-period command.
Syntax
ethernet-oam link-monitor frame-period { [threshold threshold ] [ window window ] [notify { disable | enable } ] }
no ethernet-oam link-monitor frame-period { threshold | window | notify }
Parameter
threshold —— Configure the error threshold for generating error frame period event. The range is from 1 to 4294967295 and the default value is 1.
window —— Configure the error frame period event detection interval. The range is from 148810 to 89286000. The default value is 148810 for Fast Ethernet port and 1488100 for Gigabit Ethernet port.
notify —— Enable/Disable the event notification. By default, it is enabled.
319
threshold | window | notify —— The parameter that you want to return to the default configuration.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
For error frame period event, configure the error threshold as 6 and the event detection interval as 150000 frames on Gigabit Ethernet port 1/0/4:
T2600G-28TS(config)# interface gigabitEthernet 1/0/4
T2600G-28TS(config-if)# ethernet-oam link-monitor frame-period
threshold 6 window 150000
37.6 ethernet-oam link-monitor frame-seconds
Description
The ethernet-oam link-monitor frame-seconds command is used to configure the parameters about one of the link events, error frame seconds event. To return to the default configurations, please use no ethernet-oam link-monitor frame-seconds command.
Syntax
ethernet-oam link-monitor frame-seconds { [threshold threshold ] [ window window ] [notify { disable | enable } ] }
no ethernet-oam link-monitor frame-seconds { threshold | window | notify }
Parameter
threshold —— Configure the error threshold for generating error frame seconds event. The range is from 1 to 900 and the default value is 1.
window —— Configure the error frame seconds event detection interval. The range is from 100 to 9000, in terms of 100 ms intervals. The default value is 600.
notify —— Enable/Disable the event notification. By default, it is enabled.
320
threshold | window | notify —— The parameter that you want to return to the default configuration.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
For error frame seconds event, configure the error threshold as 8 and the event detection interval as 30 seconds on Gigabit Ethernet port 5:
T2600G-28TS(config)# interface gigabitEthernet 1/0/5
T2600G-28TS(config-if)# ethernet-oam link-monitor frame-seconds
threshold 8 window 300
37.7 ethernet-oam remote-failure
Description
The ethernet-oam remote-failure command is used to configure whether to notify the link faults or not. The link faults include dying gasp and critical event. To return to the default configurations, please use no ethernet-oam remote-failure command.
Syntax
ethernet-oam remote-failure { dying-gasp | critical-event } notify { disable | enable }
no ethernet-oam remote-failure { dying-gasp | critical-event } notify
Parameter
dying-gasp —— Dying Gasp link event. Dying gasp means an unrecoverable fault, such as power failure, occurs.
critical-event —— Critical Event. Critical-event means unspecified critical event occurs.
notify ——Enable/Disable the event notification. By default, it is enabled.
321
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Disable the Dying Gasp link event notification on Gigabit Ethernet port 1/0/7:
T2600G-28TS(config)# interface gigabitEthernet 1/0/7
T2600G-28TS(config-if)# ethernet-oam remote-failure dying-gasp notify
disable
37.8 ethernet-oam remote-loopback
received-remote- loopback
Description
The ethernet-oam remote-loopback received-remote-loopback command is used to configure the client to process or to ignore the received remote loopback request. To return to the default configurations, please use no ethernet-oam remote-loopback received-remote-loopback command.
Syntax
ethernet-oam remote-loopback received-remote-loopback { process | ignore }
no ethernet-oam remote-loopback received-remote-loopback
Parameter
process —— Process the received remote loopback request.
ignore —— Ignore the received remote loopback request.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
322
Example
Configure the client to process the received remote loopback request on Gigabit Ethernet port 1:
T2600G-28TS(config)# interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)# ethernet-oam remote-loopback received
-remote-loopback process
37.9 ethernet-oam remote-loopback
Note: T2600G-18TS doesn’t support this command.
Description
The ethernet-oam remote-loopback command is used to request the remote peer to start or stop the Ethernet OAM remote loopback mode.
Syntax
ethernet-oam remote-loopback { start | stop }
Parameter
start —— Request the remote peer to start the Ethernet OAM remote loopback mode.
stop —— Request the remote peer to stop the Ethernet OAM remote loopback mode.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Request the remote peer to start the Ethernet OAM remote loopback mode on Gigabit Ethernet port 1/0/3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# ethernet-oam remote-loopback start
323
37.10 clear ethernet-oam statistics
Description
The clear ethernet-oam statistics command is used to clear Ethernet OAM statistics.
Syntax
clear ethernet-oam statistics [ interface gigabitEthernet port ]
Parameter
port —— The Gigabit Ethernet port number. By default, the Ethernet OAM statistics of all ports are cleared.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Clear Ethernet OAM statistics of Gigabit Ethernet port 1/0/3:
T2600G-28TS(config)# clear ethernet-oam statistics interface gigabit
Ethernet 1/0/3
37.11 clear ethernet-oam event-log
Description
The clear ethernet-oam event-log command is used to clear the Ethernet OAM event log.
Syntax
clear ethernet-oam event-log [ interface gigabitEthernet port ]
Parameter
port ——The Gigabit Ethernet port number. By default, the Ethernet OAM event logs of all ports are cleared.
324
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Clear Ethernet OAM event log of Gigabit Ethernet port 1/0/3:
T2600G-28TS(config)# clear ethernet-oam event-log interface
gigabitEthernet 1/0/3
37.12 show ethernet-oam configuration
Description
The show ethernet-oam configuration command is used to display Ethernet OAM configuration information.
Syntax
show ethernet-oam configuration [ interface gigabitEthernet port ]
Parameter
port —— The Gigabit Ethernet port number. By default, the Ethernet OAM configuration information of all ports is displayed.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Display Ethernet OAM configuration information of Gigabit Ethernet port 1/0/2:
T2600G-28TS(config)# show ethernet-oam configuration interface
gigabitEthernet 1/0/2
325
37.13 show ethernet-oam event-log
Description
The show ethernet-oam event-log command is used to display the Ethernet OAM event log.
Syntax
show ethernet-oam event-log [ interface gigabitEthernet port ]
Parameter
port —— The Gigabit Ethernet port number. By default, the Ethernet OAM event logs of all ports are displayed.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Display Ethernet OAM event log of Gigabit Ethernet port 1/0/2:
T2600G-28TS(config)# show ethernet-oam event-log interface
gigabitEthernet 1/0/2
37.14 show ethernet-oam statistics
Description
The show ethernet-oam statistics command is used to display the Ethernet OAM statistics.
Syntax
show ethernet-oam statistics [ interface gigabitEthernet port ]
Parameter
port —— The Gigabit Ethernet port number. By default, the Ethernet OAM statistics of all ports are displayed.
326
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Display Ethernet OAM statistics of Gigabit Ethernet port 1/0/2:
T2600G-28TS(config)# show ethernet-oam statistics interface
gigabitEthernet 1/0/2
37.15 show ethernet-oam status
Description
The show ethernet-oam status command is used to display the Ethernet OAM status of both the local and the remote client.
Syntax
show ethernet-oam status [ interface gigabitEthernet port ]
Parameter
port —— The Gigabit Ethernet port number. By default, the Ethernet OAM status of all ports is displayed.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Display Ethernet OAM status of Gigabit Ethernet port 1/0/2:
T2600G-28TS(config)# show ethernet-oam status interface
gigabitEthernet 1/0/2
327
Chapter 38 DLDP Commands
DLDP (Device Link Detection Protocol) is used to monitor the link state of fiber-optic or twisted-pair Ethernet cables. When a unidirectional link is detected, the corresponding port will be shut down automatically or manually (depending on the shut mode configured).
38.1 dldp (global) Description
The dldp command is used to enable the DLDP function globally. To disable it, please use no dldp command.
Syntax
dldp
no dldp
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Enable the DLDP function globally:
T2600G-28TS(config)# dldp
38.2 dldp interval Description
The dldp interval command is used to define the interval of sending advertisement packets on ports that are in the advertisement state.
Syntax
dldp interval interval-time
Parameter
interval-time —— The interval of sending advertisement packets. It ranges from 1 to 30 seconds. By default, it is 5 seconds.
328
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Specify the interval of sending advertisement packets as 10 seconds:
T2600G-28TS(config)# dldp interval 10
38.3 dldp shut-mode Description
The dldp shut-mode command is used to configure the shutdown mode when a unidirectional link is detected.
Syntax
dldp shut-mode { auto | manual }
Parameter
auto —— The switch automatically shuts down ports when a unidirectional link is detected. By default, the shut-mode is auto.
manual ——The switch displays an alert when a unidirectional link is detected. The operation to shut down the unidirectional link ports is accomplished by the users.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure the shut-mode as manual:
T2600G-28TS(config)# dldp shut-mode manual
329
38.4 dldp reset (global) Description
The dldp reset command is used to reset all the unidirectional links and restart the link detect process.
Syntax
dldp reset
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Reset the DLDP function globally:
T2600G-28TS(config)# dldp reset
38.5 dldp(interface) Description
The dldp command is used to enable the DLDP function of the specified port. To disable it, please use no dldp command.
Syntax
dldp
no dldp
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Enable the DLDP function of ports 1/0/2-4:
T2600G-28TS (config)# interface range gigabitEthernet 1/0/2-4
330
T2600G-28TS (config-if-range)# dldp
38.6 dldp reset (interface) Description
The dldp reset command is used to reset the specified port and restart the link detect process.
Syntax
dldp reset
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Reset the DLDP function of ports 2-4:
T2600G-28TS (config)# interface range gigabitEthernet 1/0/2-4
T2600G-28TS (config-if-range)# dldp reset
38.7 show dldp Description
The show dldp command is used to display the global configuration of DLDP function such as DLDP global state, DLDP interval and shut mode.
Syntax
show dldp
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
331
Example
Display the global configuration of DLDP function:
T2600G-28TS# show dldp
38.8 show dldp interface Description
The show dldp interface command is used to display the configuration and state of the specified Ethernet port. By default, the configuration and state of all the ports will be displayed.
Syntax
show dldp interface [gigabitEthernet port ]
Parameter
port —— The Gigabit Ethernet port number.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configuration and state of all ports:
T2600G-28TS# show dldp interface
Display the configuration and state of port 1/0/5:
T2600G-28TS# show dldp interface gigabitEthernet 1/0/5
332
Chapter 39 IGMP Snooping Commands
IGMP Snooping (Internet Group Management Protocol Snooping) is a multicast control mechanism running on Layer 2 switch. It can effectively prevent multicast groups being broadcasted in the network.
39.1 ip igmp snooping (global) Description
The ip igmp snooping command is used to configure IGMP Snooping globally. To disable the IGMP Snooping function, please use no ip igmp snooping command.
Syntax ip igmp snooping
no ip igmp snooping
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable IGMP Snooping function:
T2600G-28TS(config)# ip igmp snooping
39.2 ip igmp snooping (interface) Description
The ip igmp snooping command is used to enable the IGMP Snooping function for the desired port. To disable the IGMP Snooping function, please use no ip igmp snooping command.
Syntax ip igmp snooping
no ip igmp snooping
333
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable IGMP Snooping function of port 1/0/3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# ip igmp snooping
39.3 ip igmp snooping rtime Description
The ip igmp snooping rtime command is used to specify router port aging time globally. To restore the default timer, please use no ip igmp snooping rtime command.
Syntax ip igmp snooping rtime rtime no ip igmp snooping rtime
Parameter rtime —— Specify the aging time in seconds, ranging from 60 to 600. The default aging time is 300 seconds.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify IGMP Snooping router port aging time as 100 seconds globally:
T2600G-28TS(config)# ip igmp snooping rtime 100
334
39.4 ip igmp snooping mtime Description
The ip igmp snooping mtime command is used to specify member port aging time globally. The default aging time is 260 seconds. To restore the default timer, please use no ip igmp snooping mtime command.
Syntax ip igmp snooping mtime mtime no ip igmp snooping mtime
Parameter mtime —— Specify the aging time in seconds, ranging from 60 to 600. The default aging time is 260 seconds.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Specify IGMP Snooping member port aging time as 100 seconds globally:
T2600G-28TS(config)# ip igmp snooping mtime 100
39.5 ip igmp snooping report-suppression Description
The ip igmp snooping report-suppression command is used enable the IGMP report suppression function. When it is enabled, the switch forwards only the first IGMP report message per mulicast group to the Layer 3 device, and the subsequent IGMP reports from the same multicast group are discarded. To disable the IGMP report suppression function and forward all the IGMP reports to the Layer 3 device, please use no ip igmp snooping report-suppression command. This function is disabled by default.
Syntax ip igmp snooping report-suppression
no ip igmp snooping report-suppression
Command Mode Global Configuration Mode
335
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the IGMP report suppression function:
T2600G-28TS(config)# ip igmp snooping report-suppression
39.6 ip igmp snooping immediate-leave Description
The ip igmp snooping immediate-leave command is used to configure the Fast Leave function for port. To disable the Fast Leave function, please use no ip igmp snooping immediate-leave command.
Syntax ip igmp snooping immediate-leave
no ip igmp snooping immediate-leave
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the Fast Leave function for port 1/0/3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# ip igmp snooping immediate-leave
39.7 ip igmp snooping drop-unknown Description
The ip igmp snooping drop-unknown command is used to process the unknown multicast as discard. To disable the operation of processing the unknown multicast as discard, please use no ip igmp snooping drop-unknown command.
336
Syntax ip igmp snooping drop-unknown
no ip igmp snooping drop-unknown
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Specify the operation to process unknown multicast as discard:
T2600G-28TS(config)# ip igmp snooping drop-unknown
39.8 ip igmp snooping last-listener query-inteval Description
The ip igmp snooping last-listener query-inteval command is used to specify the interval to send Specific Query Message. The default value is 1 second. To restore the default interval, please use no ip igmp snooping last-listener query-inteval command.
Syntax ip igmp snooping last-listener query-inteval interval no ip igmp snooping last-listener query-inteval
Parameter
interval —— Specify the interval to send Specific Query Message in seconds, ranging from 1 to 5.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Specify the interval of Specific Query Message to 3 seconds:
T2600G-28TS(config)# ip igmp snooping last-listener query-inteval 3
337
39.9 ip igmp snooping last-listener query-count Description
The ip igmp snooping last-listener query-count command is used to specify the numbers of Specific Query Message to be sent. The default value is 2. To restore the default number, please use no ip igmp snooping last-listener query-count command.
Syntax ip igmp snooping last-listener query-count num no ip igmp snooping last-listener query-count
Parameter num —— Specify the numbers of Specific Query Message to be sent, ranging from 1 to 5.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Specify the number of Specific Query Message to 3:
T2600G-28TS(config)# ip igmp snooping last-listener query-count 3
39.10 ip igmp snooping vlan-config Description
The ip igmp snooping vlan-config command is used to enable VLAN IGMP Snooping function or to modify IGMP Snooping parameters, and to create static multicast IP entry. To disable the VLAN IGMP Snooping function, please use no ip igmp snooping vlan-config command. To restore the default values, please use no ip igmp snooping vlan-config with specified parameters.
Syntax ip igmp snooping vlan-config vlan-id-list [ rtime router-time | mtime member-time | rport interface { gigabitEthernet port-list | port-channel port-channel-id } ]
ip igmp snooping vlan-config vlan-id-list static ip interface { gigabitEthernet port-list | port-channel port-channel-id }
338
no ip igmp snooping vlan-config vlan-id-list [ rtime router-time | mtime member-time | rport interface { gigabitEthernet port-list | port-channel port-channel-id } ]
no ip igmp snooping vlan-config vlan-id-list static ip interface { gigabitEthernet port-list | port-channel port-channel-id }
Parameter vlan-id-list —— The ID list of the VLAN desired to modify configuration, ranging from 1 to 4094, in the format of 1-3, 5.
router-time —— Router Port Time. Within this time, if the switch does not receive IGMP query message from the router port, it will consider this port is not a router port any more. Router Port Time ranges from 60 to 600 in seconds. By default, it is 0 and the global router-time will be used.
member-time —— Member Port Time. Within this time, if the switch does not receive IGMP report message from the member port, it will consider this port is not a member port any more. Member Port Time ranges from 60 to 600 in seconds. By default, it is 0 and the global member-time will be used.
port-list —— The list of Ethernet ports.
port-channel-id —— The ID of the port channels.
ip —— The static multicast IP address.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the IGMP Snooping function and modify Router Port Time as 300 seconds, Member Port Time as 200 seconds for VLAN 1-3, and set the router port as 1/0/1 for VLAN 1-2:
T2600G-28TS(config)# ip igmp snooping vlan-config 1-3 rtime 300
T2600G-28TS(config)# ip igmp snooping vlan-config 1-3 mtime 200
T2600G-28TS(config)# ip igmp snooping vlan-config 1-2 rport interface
gigabitEthernet 1/0/1
Add static multicast IP address 225.0.0.1, which corresponds to VLAN 2, and configure the forward ports as ports 1/0/1-3:
339
T2600G-28TS(config)# ip igmp snooping vlan-config 2 static 225.0.0.1
interface gigabitEthernet 1/0/1-3
39.11 ip igmp snooping vlan-config
(router-port-forbidden) Description
This command is used to forbid the specified ports as being router ports in the specified VLAN(s). To delete the forbidden router ports, please use no ip igmp snooping vlan-config vlan-id-list router-ports-forbidd command.
Syntax ip igmp snooping vlan-config vlan-id-list router-port-forbidd interface { gigabitEthernet port-list | port-channel port-channel-id }
no ip igmp snooping vlan-config vlan-id-list router-port-forbidd interface [ gigabitEthernet port-list | port-channel port-channel-id ]
Parameter vlan-id-list —— The ID list of the VLAN desired to modify configuration, ranging from 1 to 4094, in the format of 1-3, 5.
port-list —— Forbid the specified ports as being router ports. Packets sent from multicast routers to these ports will be discarded.
port-channel-id —— Forbid the specified port-channels as being router ports. Packets sent from multicast routers to these port-channels will be discarded.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Forbid the Ethernet ports 1/0/1-3 as being router ports in VLAN 1 :
T2600G-28TS(config)# ip igmp snooping vlan-config 1 router-port-forbidd
interface gigabitEthernet 1/0/1-3
340
39.12 ip igmp snooping multi-vlan-config Description
The ip igmp snooping multi-vlan-config command is used to create Multicast VLAN. To delete the corresponding Multicast VLAN, please use no ip igmp snooping multi-vlan-config command. To restore the default values, please use no ip igmp snooping multi-vlan-config with specified parameters.
Syntax ip igmp snooping multi-vlan-config [ vlan-id ] [ rtime router-time | mtime member-time | rport interface { gigabitEthernet port-list | port-channel port-channel-id } ]
no ip igmp snooping multi-vlan-config [ rtime router-time | mtime member-time | rport interface { gigabitEthernet port-list | port-channel port-channel-id } ]
Parameter vlan-id —— The ID of the multicast VLAN desired to create or modify, ranging from 2 to 4094. If not specified, the default multicast VLAN will be selected.
router-time —— Router Port Time. Within this time, if the switch does not receive IGMP query message from the router port, it will consider this port is not a router port any more. Router Port Time ranges from 60 to 600 in seconds. By default, it is 0 and the global router-time will be used.
member-time —— Member Port Time. Within this time, if the switch does not receive IGMP report message from the member port, it will consider this port is not a member port any more. Member Port Time ranges from 60 to 600 in seconds. By default, it is 0 and the global member-time will be used.
port-list —— The list of Ethernet ports.
port-channel-id —— The ID of the port channels.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Enable Multicast VLAN 3, and configure Router Port Time as 100 seconds, Member Port Time 100 seconds, and Static Router Port port 1/0/3:
341
T2600G-28TS(config)# ip igmp snooping multi-vlan-config 3 rtime 100
T2600G-28TS(config)# ip igmp snooping multi-vlan-config 3 mtime 100
T2600G-28TS(config)# ip igmp snooping multi-vlan-config 3 rport
interface gigabitEthernet 1/0/3
39.13 ip igmp snooping multi-vlan-config
(router-port-forbidden) Description
This command is used to forbid the specified ports as being router ports in the specified multicast VLAN. To delete the forbidden router ports, please use no ip igmp snooping multi-vlan-config router-ports-forbidd command.
Syntax ip igmp snooping multi-vlan-config [ vlan-id ] router-port-forbidd interface { gigabitEthernet port-list | port-channel port-channel-id }
no ip igmp snooping multi-vlan-config router-port-forbidd [ interface { gigabitEthernet port-list | port-channel port-channel-id } ]
Parameter vlan-id—— The ID of the multicast VLAN.
port-list —— Forbid the specified ports as being router ports. Packets sent from multicast routers to these ports will be discarded.
port-channel-id —— Forbid the specified port-channels as being router ports. Packets sent from multicast routers to these port-channels will be discarded.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Forbid the Ethernet ports 1/0/1-3 as being router ports in multicast VLAN 1 :
T2600G-28TS(config)# ip igmp snooping multi-vlan-config 1
router-port-forbidd interface gigabitEthernet 1/0/1-3
342
39.14 ip igmp snooping multi-vlan-config
(source-ip-replace) Description
This command is used to replace the multicast source IP address of the IGMP packets in the specified multicast VLAN. To delete the forbidden router ports, please use no ip igmp snooping multi-vlan-config replace-sourceip command.
Syntax ip igmp snooping multi-vlan-config [ vlan-id ] replace-sourceip ip
no ip igmp snooping multi-vlan-config replace-sourceip
Parameter vlan-id—— The ID of the multicast VLAN.
ip —— Specify the IP address. The switch will use this IP address to replace the source IP address of the IGMP packets.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Replace the source IP address of the IGMP packets in multicast VLAN 1 as 192.168.0.112:
T2600G-28TS(config)# ip igmp snooping multi-vlan-config 1
replace-sourceip 192.168.0.112
39.15 ip igmp snooping querier vlan Description
The ip igmp snooping querier vlan command is used to enable the IGMP Snooping Querier function of the VLAN(s). To disable the IGMP Snooping Querier function of certain VLANs, please use no ip igmp snooping querier vlan command.
Syntax ip igmp snooping querier vlan vlan-id
343
no ip igmp snooping querier vlan vlan-id
Parameter vlan-id — VLAN ID, ranging from 1 to 4094.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the IGMP Snooping Querier function of VLAN 1:
T2600G-28TS(config)#ip igmp snooping querier vlan 1
39.16 ip igmp snooping querier vlan (general query) Description
The ip igmp snooping querier vlan command is used to configure the parameters for IGMP Snooping Querier to send a general query frame. To return to the default configuration, please use no ip igmp snooping querier vlan command.
Syntax ip igmp snooping querier vlan vlan-id { query-interval interval | max-response-time response-time | general-query source-ip ip-addr }
no ip igmp snooping querier vlan vlan-id { query-interval | max-response-time | general-query source-ip }
Parameter vlan-id —— VLAN ID, ranging from 1 to 4094.
interval —— The time interval to send a general query frame by IGMP Snooping Querier, ranging from 10 to 300 (Seconds). By default, it is 60 seconds.
response-time —— The maximal time for the host to respond to a general query frame, ranging from 1 to 25 (Seconds). By default, it is 10 Seconds.
ip-addr —— The source IP of the general query frame sent by IGMP Snooping Querier. It should not be a multicast IP or a broadcast IP. By default, it is 192.168.0.1.
344
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example For VLAN 2, specify its query-interval as 200 seconds, and the response-time as 20 seconds:
T2600G-28TS(config)#ip igmp snooping querier vlan 2 query-interval 200
T2600G-28TS(config)#ip igmp snooping querier vlan 2
max-response-time 20
39.17 ip igmp snooping max-groups Description
The ip igmp snooping max-groups command is used to configure the maximum number of groups that a port can join in. The ip igmp snooping max-groups action is used to configure the action that the port takes when it receives an IGMP report message and the maximum number of entries is in the forwarding table. To remove the maximum group limitation and return to the default of no limitation on the specified port, please use the no ip igmp snooping max-groups command. To return to the default action of dropping the report, please use the no ip igmp snooping max-groups action command. These commands only apply to the dynamic multicast groups.
Syntax ip igmp snooping max-groups [ maxgroup ]
ip igmp snooping max-groups action { drop | replace }
no ip igmp snooping max-groups
no ip igmp snooping max-groups action
Parameter maxgroup —— Specify the maximum numbers of groups that the port can join. It ranges from 0 to 1000 and the default value is 1000.
drop —— When the number of the dynamic multicast groups that a port joins has exceeded the max-group, the port will not join any new multicast group.
345
replace —— When the number of the dynamic multicast groups that a port joins has exceeded the max-group, the newly joined multicast group will replace an existing multicast group with the lowest multicast group address.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Specify the maximum numbers of groups that ports 1/0/2-5 can join as 10, and configure the throttling action as replace:
T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-5
T2600G-28TS(config-if-range)#ip igmp snooping max-groups 10
T2600G-28TS(config-if-range)#ip igmp snooping max-groups action
replace
39.18 ip igmp snooping authentication Description
The ip igmp snooping authenticaiton command is used to authenticate the users who want to join the limited multicast source. To disable the multicast authentication, please use no ip igmp snooping authentication command.
Syntax
ip igmp snooping authentication
no ip igmp snooping authentication
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
346
User Guidelines The IGMP Authentication feature will take effect only when AAA function is enabled and the RADIUS server is configured. For how to enable AAA function and configure RADIUS server, please refer to aaa enable and radius-server host.
Example
Enable IGMP authentication on port 1/0/3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# ip igmp snooping authentication
39.19 ip igmp snooping accounting Description
The ip igmp snooping accounting command is used to enable IGMP accounting globally. To disable the IGMP accouting, please use no ip igmp snooping accounting command.
Syntax
ip igmp snooping accounting
no ip igmp snooping accounting
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable IGMP accounting globally:
T2600G-28TS(config)# ip igmp snooping accounting
39.20 ip igmp profile Description
The ip igmp profile command is used to create the configuration profile. To delete the corresponding profile, please use no ip igmp profile command.
347
Syntax
ip igmp profile id
no ip igmp profile id
Parameter
id —— Specify the id of the configuration profile, ranging from 1 to 999.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create the profile 1:
T2600G-28TS(config)# ip igmp profile 1
39.21 deny Description
The deny command is used to configure the filtering mode of profile as deny.
Syntax
deny
Command Mode
Profile Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the filtering mode of profile 1 as deny:
T2600G-28TS(config)# ip igmp profile 1 T2600G-28TS(config-igmp-profile)#deny
348
39.22 permit Description
The permit command is used to configure the filtering mode of profile as permit.
Syntax
permit
Command Mode
Profile Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure the filtering mode of profile 1 as permit:
T2600G-28TS(config)# ip igmp profile 1 T2600G-28TS(config-igmp-profile)#permit
39.23 range Description
The range command is used to configure the range of the profile’s filtering multicast address. To delete the corresponding filtering multicast address, please use no range command. A profile contains 16 filtering IP-range entries at most.
Syntax
range start-ip end-ip
no range start-ip end-ip
Parameter
start-ip —— The start filtering multicast IP address.
end-ip —— The end filtering multicast IP address.
Command Mode
Profile Configuration Mode
349
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure one of the filter multicast address entry as range 225.1.1.1 to 226.3.2.1 in profile 1:
T2600G-28TS(config)# ip igmp profile 1 T2600G-28TS(config-igmp-profile)#range 225.1.1.1 226.3.2.1
39.24 ip igmp filter Description
The ip igmp filter command is used to bind the specified profile to the interface. To delete the binding, please use no ip igmp filter command.
Syntax ip igmp filter profile-id no ip igmp filter
Parameter profile-id —— Specify the profile ID, ranging from 1 to 999.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Bind profile 1 to interface gigabitEthernet 1/0/2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# ip igmp filter 1
39.25 clear ip igmp snooping statistics Description
The clear ip igmp snooping statistics command is used to clear the statistics of the IGMP packets.
350
Syntax clear ip igmp snooping statistics
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Clear the statistics of the IGMP packets:
T2600G-28TS(config)# clear ip igmp snooping statistics
39.26 show ip igmp snooping Description
The show ip igmp snooping command is used to display the global configuration of IGMP snooping.
Syntax show ip igmp snooping
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the global configuration of IGMP:
T2600G-28TS# show ip igmp snooping
39.27 show ip igmp snooping interface Description
The show ip igmp snooping interface command is used to display the port configuration of IGMP snooping.
Syntax show ip igmp snooping interface [ gigabitEthernet [ port | port-list ] ] { basic-config | max-groups | packet-stat }
351
show ip igmp snooping interface [ port-channel [ port-channel-id ] ] { basic-config | max-groups }
Parameter port —— The Ethernet port number.
port-list —— The list of Ethernet ports.
basic-config | max-groups | packet-stat —— The related configuration information selected to display.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the IGMP baisic configuration configuration of all ports and port channels:
T2600G-28TS# show ip igmp snooping interface basic-config
Display the IGMP basic configuration of port 1/0/2:
T2600G-28TS# show ip igmp snooping interface gigabitEthernet 1/0/2
basic-config
Display the IGMP packet statistics of ports 1/0/1-4:
T2600G-28TS# show ip igmp snooping interface gigabitEthernet 1/0/1-4
packet-stat
39.28 show ip igmp snooping vlan Description
The show ip igmp snooping vlan command is used to display the VLAN configuration of IGMP snooping.
Syntax show ip igmp snooping vlan [ vlan-id ]
Parameter vlan-id ——The VLAN ID selected to display.
Command Mode Privileged EXEC Mode and Any Configuration Mode
352
Privilege Requirement
None.
Example Display the IGMP snooping configuration information of VLAN 2:
T2600G-28TS# show ip igmp snooping vlan 2
39.29 show ip igmp snooping multi-vlan Description
The show ip igmp snooping multi-vlan command is used to display the Multicast VLAN configuration.
Syntax show ip igmp snooping multi-vlan
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the Multicast VLAN configuration:
T2600G-28TS# show ip igmp snooping multi-vlan
39.30 show ip igmp snooping groups Description
The show ip igmp snooping groups command is used to display the information of all IGMP snooping groups. It can be extended to some other commands to display the dynamic and static multicast information of a selected VLAN.
Syntax show ip igmp snooping groups [ vlan { vlan-id } ] [ multicast_addr | count | dynamic | dynamic count | static | static count ]
Parameter vlan-id ——The VLAN ID selected to display the information of all multicast items.
multicast_addr —— IP address of the multicast group.
353
count—— The numbers of all multicast groups.
dynamic—— Display dynamic multicast groups.
dynamic count—— The numbers of all dynamic multicast groups.
static—— Display static multicast groups.
static count—— The numbers of all static multicast groups.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the information of all IGMP snooping groups:
T2600G-28TS#show ip igmp snooping groups
Display all the multicast entries in VLAN 5:
T2600G-28TS(config)#show ip igmp snooping groups vlan 5
Display the count of multicast entries in VLAN 5:
T2600G-28TS(config)#show ip igmp snooping groups vlan 5 count
Display the dynamic multicast groups of VLAN 5
T2600G-28TS(config)#show ip igmp snooping groups vlan 5 dynamic
Display the static multicast groups of VLAN 5
T2600G-28TS(config)#show ip igmp snooping groups vlan 5 static
Display the count of dynamic multicast entries of VLAN 5
T2600G-28TS(config)#show ip igmp snooping groups vlan 5 dynamic
count
Display the count of static multicast entries of VLAN 5
T2600G-28TS(config)#show ip igmp snooping groups vlan 5 static count
39.31 show ip igmp snooping querier Description
The show ip igmp snooping querier command is used to display the Querier configuration of VLAN.
354
Syntax show ip igmp snooping querier [ vlan vlan-id ]
Parameter vlan-id ——The VLAN ID selected to display, ranging from 1 to 4094.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display all Querier information:
T2600G-28TS(config)# show ip igmp snooping querier
39.32 show ip igmp profile Description
The show ip igmp profile command is used to display the configuration information of all the profiles or a specific profile.
Syntax
show ip igmp profile [ id ]
Parameter
id —— Specify the ID of the profile, ranging from 1 to 999.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configuration information of all profiles:
T2600G-28TS(config)# show ip igmp profile
355
Chapter 40 MLD Snooping Commands
MLD Snooping (Multicast Listener Discovery Snooping) is a multicast control mechanism running on Layer 2 switch. It can effectively prevent multicast groups being broadcasted in the IPv6 network.
40.1 ipv6 mld snooping (global) Description
The ipv6 mld snooping command is used to enable MLD Snooping function globally. If this function is disabled, all related MLD Snooping function would not work. To disable this function, please use no ipv6 mld snooping command.
Syntax ipv6 mld snooping no ipv6 mld snooping
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Enable MLD Snooping:
T2600G-28TS(config)# ipv6 mld snooping
40.2 ipv6 mld snooping (interface) Description
The ipv6 mld snooping command is used to enable MLD Snooping function on the desired port. To disable this function, please use no ipv6 mld snooping command.
Syntax ipv6 mld snooping no ipv6 mld snooping
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
356
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Enable MLD Snooping on port 1/0/3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# ipv6 mld snooping
40.3 ipv6 mld snooping rtime Description
The ipv6 mld snooping rtime command is used to specify router port aging time globally. To restore the default timer, please use no ipv6 mld snooping rtime command.
Syntax ipv6 mld snooping rtime rtime no ipv6 mld snooping rtime
Parameter rtime —— Specify the aging time in seconds, ranging from 60 to 600. The default aging time is 300 seconds.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Specify MLD Snooping router port aging time as 100 seconds globally:
T2600G-28TS(config)# ipv6 mld snooping rtime 100
40.4 ipv6 mld snooping mtime Description
The ipv6 mld snooping mtime command is used to specify member port aging time globally. The default aging time is 260 seconds. To restore the default timer, please use no ipv6 mld snooping mtime command.
Syntax ipv6 mld snooping mtime mtime no ipv6 mld snooping mtime
357
Parameter mtime —— Specify the aging time in seconds, ranging from 60 to 600. The default aging time is 260 seconds.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Specify MLD Snooping member port aging time as 100 seconds globally:
T2600G-28TS(config)# ipv6 mld snooping mtime 100
40.5 ipv6 mld snooping report-suppression Description
The ipv6 mld snooping report-suppression command is used enable the MLD report suppression function. When it is enabled, the switch forwards only the first MLD report message per mulicast group to the Layer 3 device, and the subsequent MLD reports from the same multicast group are discarded. To disable the MLD report suppression function and forward all the MLD reports to the Layer 3 device, please use no ip igmp snooping report-suppression command. This function is disabled by default.
Syntax ipv6 mld snooping report-suppression no ipv6 mld snooping report-suppression
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Enable MLD Report message suppression function:
T2600G-28TS(config)# ipv6 mld snooping report-suppression
358
40.6 ipv6 mld snooping immediate-leave Description
The ipv6 mld snooping immediate-leave command is used to configure the Fast Leave function for port. To disable the Fast Leave function, please use no ipv6 mld snooping immediate-leave command.
Syntax ipv6 mld snooping immediate-leave
no ipv6 mld snooping immediate-leave
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Enable the Fast Leave function for port 1/0/3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# ipv6 mld snooping immediate-leave
40.7 ipv6 mld snooping drop-unknown Description
The ipv6 mld snooping drop-unknown command is used to enable the unknown multicast packets filter function. To disable this function, please use no ipv6 mld snooping drop-unknown command. By default, it is disabled.
Syntax ipv6 mld snooping drop-unknown no ipv6 mld snooping drop-unknown
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Enable unknown multicast filter function:
T2600G-28TS(config)# ipv6 mld snooping drop-unknown
359
40.8 ipv6 mld snooping last-listener query-inteval Description
The ipv6 mld snooping last-listener query-inteval command is used to specify the interval to send Specific Query Message. The default value is 1 second. To restore the default interval, please use no ipv6 mld snooping last-listener query-inteval command.
Syntax ipv6 mld snooping last-listener query-inteval interval no ipv6 mld snooping last-listener query-inteval
Parameter interval —— Specify the interval to send Specific Query Message in seconds, ranging from 1 to 5.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Specify the interval of Specific Query Message to 3 seconds:
T2600G-28TS(config)# ipv6 mld snooping last-listener query-inteval 3
40.9 ipv6 mld snooping last-listener query-count Description
The ipv6 mld snooping last-listener query-count command is used to specify the numbers of Specific Query Message to be sent. The default value is 2. To restore the default number, please use no ipv6 mld snooping last-listener query-count command.
Syntax ipv6 mld snooping last-listener query-count num no ipv6 mld snooping last-listener query-count
Parameter num —— Specify the numbers of Specific Query Message to be sent, ranging from 1 to 5.
Command Mode Global Configuration Mode
360
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Specify the number of Specific Query Message to 3:
T2600G-28TS(config)# ipv6 mld snooping last-listener query-count 3
40.10 ipv6 mld snooping vlan-config Description
The ipv6 mld snooping vlan-config command is used to enable VLAN MLD Snooping function or to modify MLD Snooping parameters, and to create static multicast IP entry. To disable the VLAN MLD Snooping function, please use no ipv6 mld snooping vlan-config command.
Syntax ipv6 mld snooping vlan-config vlan-id-list [ rtime router-time | mtime member-time | rport interface { gigabitEthernet port-list | port-channel port-channel-id } ]
ipv6 mld snooping vlan-config vlan-id-list static ip interface { gigabitEthernet port-list | port-channel port-channel-id }
no ipv6 mld snooping vlan-config vlan-id-list [ rtime router-time | mtime member-time | rport interface { gigabitEthernet port-list | port-channel port-channel-id } ]
no ipv6 mld snooping vlan-config vlan-id-list static ip interface { gigabitEthernet port-list | port-channel port-channel-id }
Parameter vlan-id-list —— The ID list of the VLAN desired to modify configuration, ranging from 1 to 4094, in the format of 1-3, 5.
router-time —— Router Port Time. Within this time, if the switch does not receive IGMP query message from the router port, it will consider this port is not a router port any more. Router Port Time ranges from 60 to 600 in seconds. By default, it is 0 and the global router-time will be used.
member-time —— Member Port Time. Within this time, if the switch does not receive IGMP report message from the member port, it will consider this port is not a member port any more. Member Port Time ranges from 60 to 600 in seconds. By default, it is 0 and the global member-time will be used.
port-list —— The list of Ethernet ports.
361
port-channel-id —— The ID of the port channels.
ip —— The static multicast IP address.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Enable the MLD Snooping function and modify Router Port Time as 300 seconds, Member Port Time as 200 seconds for VLAN 1-3, and set the router port as 1/0/1 for VLAN 1-2:
T2600G-28TS(config)# ipv6 mld snooping vlan-config 1-3 rtime 300
T2600G-28TS(config)# ipv6 mld snooping vlan-config 1-3 mtime 200
T2600G-28TS(config)# ipv6 mld snooping vlan-config 1-2 rport interface
gigabitEthernet 1/0/1
Add static multicast IP address ff01::1234:01, which corresponds to VLAN 2, and configure the forward ports as ports 1/0/1-3:
T2600G-28TS(config)# ipv6 mld snooping vlan-config 2 static
ff01::1234:01 interface gigabitEthernet 1/0/1-3
40.11 ip mld snooping vlan-config
(router-port-forbidden) Description
This command is used to forbid the specified ports as being router ports in the specified VLAN(s). To delete the forbidden router ports, please use no ipv6 mld snooping vlan-config vlan-id-list router-ports-forbidd command.
Syntax ipv6 mld snooping vlan-config vlan-id-list router-port-forbidd interface { gigabitEthernet port-list | port-channel port-channel-id }
no ipv6 mld snooping vlan-config vlan-id-list router-port-forbidd interface [ gigabitEthernet port-list | port-channel port-channel-id ]
362
Parameter vlan-id-list —— The ID list of the VLAN desired to modify configuration, ranging from 1 to 4094, in the format of 1-3, 5.
port-list —— Forbid the specified ports as being router ports. Packets sent from multicast routers to these ports will be discarded.
port-channel-id —— Forbid the specified port-channels as being router ports. Packets sent from multicast routers to these port-channels will be discarded.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Forbid the Ethernet ports 1/0/1-3 as being router ports in VLAN 1 :
T2600G-28TS(config)# ipv6 mld snooping vlan-config 1
router-port-forbidd interface gigabitEthernet 1/0/1-3
40.12 ipv6 mld snooping multi-vlan-config Description
The ipv6 mld snooping multi-vlan-config command is used to create Multicast VLAN. To delete the corresponding Multicast VLAN, please use no ipv6 mld snooping multi-vlan-config command. To restore the default values, please use no ipv6 mld snooping multi-vlan-config with specified parameters.
Syntax ipv6 mld snooping multi-vlan-config [ vlan-id ] [ rtime router-time | mtime member-time | rport interface { gigabitEthernet port-list | port-channel port-channel-id } ]
no ipv6 mld snooping multi-vlan-config [ rtime router-time | mtime member-time | rport interface { gigabitEthernet port-list | port-channel port-channel-id } ]
Parameter vlan-id —— The ID of the multicast VLAN desired to create or modify, ranging from 2 to 4094. If not specified, the default multicast VLAN will be selected.
363
router-time —— Router Port Time. Within this time, if the switch does not receive IGMP query message from the router port, it will consider this port is not a router port any more. Router Port Time ranges from 60 to 600 in seconds. By default, it is 0 and the global router-time will be used.
member-time —— Member Port Time. Within this time, if the switch does not receive IGMP report message from the member port, it will consider this port is not a member port any more. Member Port Time ranges from 60 to 600 in seconds. By default, it is 0 and the global member-time will be used.
port-list —— The list of Ethernet ports.
port-channel-id —— The ID of the port channels.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Enable Multicast VLAN 3, and configure Router Port Time as 100 seconds, Member Port Time 100 seconds, and Static Router Port port 1/0/3:
T2600G-28TS(config)# ipv6 mld snooping multi-vlan-config 3 rtime 100
T2600G-28TS(config)# ipv6 mld snooping multi-vlan-config 3 mtime 100
T2600G-28TS(config)# ipv6 mld snooping multi-vlan-config 3 rport
interface gigabitEthernet 1/0/3
40.13 ipv6 mld snooping multi-vlan-config
(router-port-forbidden) Description
This command is used to forbid the specified ports as being router ports in the specified multicast VLAN. To delete the forbidden router ports, please use no ipv6 mld snooping multi-vlan-config router-ports-forbidd command.
Syntax ipv6 mld snooping multi-vlan-config [ vlan-id ] router-port-forbidd interface { gigabitEthernet port-list | port-channel port-channel-id }
364
no ipv6 mld snooping multi-vlan-config router-port-forbidd [ interface { gigabitEthernet port-list | port-channel port-channel-id } ]
Parameter vlan-id—— The ID of the multicast VLAN.
port-list —— Forbid the specified ports as being router ports. Packets sent from multicast routers to these ports will be discarded.
port-channel-id —— Forbid the specified port-channels as being router ports. Packets sent from multicast routers to these port-channels will be discarded.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Forbid the Ethernet ports 1/0/1-3 as being router ports in multicast VLAN 1 :
T2600G-28TS(config)# ipv6 mld snooping multi-vlan-config 1
router-port-forbidd interface gigabitEthernet 1/0/1-3
40.14 ipv6 mld snooping multi-vlan-config
(source-ip-replace) Description
This command is used to replace the multicast source IP address of the MLD packets in the specified multicast VLAN. To delete the forbidden router ports, please use no ipv6 mld snooping multi-vlan-config replace-sourceip command.
Syntax ipv6 mld snooping multi-vlan-config [ vlan-id ] replace-sourceip ip
no ipv6 mld snooping multi-vlan-config replace-sourceip
Parameter vlan-id—— The ID of the multicast VLAN.
ip —— Specify the IP address. The switch will use this IP address to replace the source IP address of the MLD packets.
Command Mode Global Configuration Mode
365
Privilege Requirement
Only Admin level users have access to these commands.
Example Replace the source IP address of the MLD packets in multicast VLAN 1 as fe80::02ff:ffff:fe00:0001:
T2600G-28TS(config)# ipv6 mld snooping multi-vlan-config 1
replace-sourceip fe80::02ff:ffff:fe00:0001
40.15 ipv6 mld snooping querier vlan Description
The ipv6 mld snooping querier vlan command is used to enable the MLD Querier function. To disable this function, please use no ipv6 mld snooping querier vlan command.
Syntax
ipv6 mld snooping querier vlan vlan-id no ipv6 mld snooping querier vlan vlan-id
Parameter vlan-id —— The VLAN that enables the MLD querier function, ranging from 1 to 4094.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Enable MLD Querier function on VLAN 2:
T2600G-28TS(config)# ipv6 mld snooping querier vlan 2
40.16 ipv6 mld snooping querier vlan (general
query) Description
The ipv6 mld snooping querier vlan command is used to configure the parameters for MLD Snooping Querier to send a general query frame. To
366
return to the default configuration, please use no ipv6 mld snooping querier vlan command.
Syntax ipv6 mld snooping querier vlan vlan-id { query-interval interval | max-response-time response-time | general-query source-ip ip-addr }
no ipv6 mld snooping querier vlan vlan-id { query-interval | max-response-time | general-query source-ip }
Parameter vlan-id —— VLAN ID, ranging from 1 to 4094.
interval —— The time interval to send a general query frame by MLD Snooping Querier, ranging from 10 to 300 (Seconds). By default, it is 60 seconds.
response-time —— The maximal time for the host to respond to a general query frame, ranging from 1 to 25 (Seconds). By default, it is 10 Seconds.
ip-addr —— The source IP of the general query frame sent by MLD Snooping Querier. It should not be a multicast IP or a broadcast IP. By default, it is fe80::02ff:ffff:fe00:0001.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example For VLAN 2, specify its query-interval as 200 seconds, and the response-time as 20 seconds:
T2600G-28TS(config)#ipv6 mld snooping querier vlan 2 query-interval
200
T2600G-28TS(config)#ipv6 mld snooping querier vlan 2
max-response-time 20
40.17 ipv6 mld snooping max-groups Description
The ipv6 mld snooping max-groups command is used to configure the maximum number of groups that a port can join in. The ipv6 mld snooping max-groups action is used to configure the action that the port takes when it
367
receives an MLD report message and the maximum number of entries is in the forwarding table. To remove the maximum group limitation and return to the default of no limitation on the specified port, please use the no ipv6 mld snooping max-groups command. To return to the default action of dropping the report, please use the no ipv6 mld snooping max-groups action command. These commands only apply to the dynamic multicast groups.
Syntax ipv6 mld snooping max-groups [ maxgroup ]
ipv6 mld snooping max-groups action { drop | replace }
no ipv6 mld snooping max-groups
no ipv6 mld snooping max-groups action
Parameter maxgroup —— Specify the maximum numbers of groups that the port can join. It ranges from 0 to 1000 and the default value is 1000.
drop —— When the number of the dynamic multicast groups that a port joins has exceeded the max-group, the port will not join any new multicast group.
replace —— When the number of the dynamic multicast groups that a port joins has exceeded the max-group, the newly joined multicast group will replace an existing multicast group with the lowest multicast group address.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Specify the maximum numbers of groups that ports 1/0/2-5 can join as 10, and configure the throttling action as replace:
T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-5
T2600G-28TS(config-if-range)#ipv6 mld snooping max-groups 10
T2600G-28TS(config-if-range)#ipv6 mld snooping max-groups action
replace
368
40.18 ipv6 mld profile Description
The ipv6 mld profile command is used to create the configuration profile. To delete the corresponding profile, please use no ipv6 mld profile command.
Syntax
ipv6 mld profile id
no ipv6 mld profile id
Parameter
id —— Specify the id of the configuration profile, ranging from 1 to 999.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Create the profile 1:
T2600G-28TS(config)# ipv6 mld profile 1
40.19 deny Description
The deny command is used to configure the filtering mode of profile as deny.
Syntax
deny
Command Mode
Profile Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure the filtering mode of profile 1 as deny:
369
T2600G-28TS(config)# ipv6 mld profile 1 T2600G-28TS(config-igmp-profile)#deny
40.20 permit Description
The permit command is used to configure the filtering mode of profile as permit.
Syntax
permit
Command Mode
Profile Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure the filtering mode of profile 1 as permit:
T2600G-28TS(config)# ipv6 mld profile 1 T2600G-28TS(config-igmp-profile)#permit
40.21 range Description
The range command is used to configure the range of the profile’s filtering multicast address. To delete the corresponding filtering multicast address, please use no range command. A profile contains 16 filtering IP-range entries at most.
Syntax
range start-ip end-ip
no range start-ip end-ip
Parameter
start-ip —— Start IPv6 multicast address of the filter entry..
end-ip —— End IPv6 multicast address of the filter entry.
370
Command Mode
Profile Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example
Configure one of the filter multicast address entry as range ff80::1234 to ff80::1235 in profile 1:
T2600G-28TS(config)# ipv6 mld profile 1 T2600G-28TS(config-igmp-profile)#range ff80::1234 ff80::1235
40.22 ipv6 mld filter Description
The ipv6 mld filter command is used to bind the specified profile to the interface. To delete the binding, please use no ipv6 mld filter command.
Syntax ipv6 mld filter profile-id no ipv6 mld filter
Parameter profile-id —— Specify the profile ID, ranging from 1 to 999.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Bind profile 1 to interface gigabitEthernet 1/0/2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# ipv6 mld filter 1
40.23 clear ipv6 mld snooping statistics Description
The clear ipv6 mld snooping statistics command is used to clear the statistics of the MLD packets.
371
Syntax clear ipv6 mld snooping statistics
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Clear the statistics of the MLD packets:
T2600G-28TS(config)# clear ipv6 mld snooping statistics
40.24 show ipv6 mld snooping Description
The show ipv6 mld snooping command is used to display the global configuration of MLD Snooping.
Syntax show ipv6 mld snooping
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the global configuration of MLD Snooping:
T2600G-28TS(config)# show ipv6 mld snooping
40.25 show ipv6 mld snooping interface Description
The show ipv6 mld snooping interface command is used to display the port configuration of MLD snooping.
Syntax show ipv6 mld snooping interface [ gigabitEthernet [ port | port-list ] ] { basic-config | max-groups | packet-stat }
372
show ipv6 mld snooping interface [ port-channel [ port-channel-id ] ] { basic-config | max-groups }
Parameter port —— The Ethernet port number.
port-list —— The list of Ethernet ports.
basic-config | max-groups | packet-stat —— The related configuration information selected to display.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the MLD baisic configuration configuration of all ports and port channels:
T2600G-28TS# show ipv6 mld snooping interface basic-config
Display the MLD basic configuration of port 1/0/2:
T2600G-28TS# show ipv6 mld snooping interface gigabitEthernet 1/0/2
basic-config
Display the MLD packet statistics of ports 1/0/1-4:
T2600G-28TS# show ipv6 mld snooping interface gigabitEthernet 1/0/1-4
packet-stat
40.26 show ipv6 mld snooping vlan Description
The show ipv6 mld snooping vlan command is used to display VLAN information of MLD Snooping.
Syntax show ipv6 mld snooping vlan [ vlan-id ]
Parameter vlan-id —— The VLAN ID selected to display, ranging from 1 to 4094.
Command Mode Privileged EXEC Mode and Any Configuration Mode
373
Privilege Requirement
None.
Example Display all of the VLAN information:
T2600G-28TS(config)# show ipv6 mld snooping vlan
40.27 show ipv6 mld snooping multi-vlan Description
The show ipv6 mld snooping multi-vlan command is used to display the Multicast VLAN configuration.
Syntax show ipv6 mld snooping multi-vlan
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the Multicast VLAN configuration:
T2600G-28TS# show ipv6 mld snooping multi-vlan
40.28 show ipv6 mld snooping groups Description
The show ipv6 mld snooping groups command is used to display multicast groups.
Syntax show ipv6 mld snooping groups [ vlan { vlan-id } ] [ ipv6_multicast_addr | count | dynamic | dynamic count | static | static count ]
Parameter vlan-id ——The VLAN ID selected to display the information of all multicast items.
ipv6_multicast_addr —— IPv6 address of the multicast group.
count—— The numbers of all multicast groups.
dynamic—— Display dynamic multicast groups.
374
dynamic count—— The numbers of all dynamic multicast groups.
static—— Display static multicast groups.
static count—— The numbers of all static multicast groups.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display all of the multicast groups:
T2600G-28TS(config)# show ipv6 mld snooping groups
40.29 show ipv6 mld snooping querier Description
The show ipv6 mld snooping querier command is used to display the Querier configuration of VLAN.
Syntax show ipv6 mld snooping querier [ vlan vlan-id ]
Parameter vlan-id ——The VLAN ID selected to display, ranging from 1 to 4094.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display all Querier information:
T2600G-28TS(config)# show ipv6 mld snooping querier
40.30 show ipv6 mld profile Description
The show ipv6 mld profile command is used to display the configuration information of all the profiles or a specific profile.
375
Syntax
show ipv6 mld profile [ id ]
Parameter
id —— Specify the ID of the profile, ranging from 1 to 999.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configuration information of all profiles:
T2600G-28TS(config)# show ipv6 mld profile
376
Chapter 41 SNMP Commands
SNMP (Simple Network Management Protocol) functions are used to manage the network devices for a smooth communication, which can facilitate the network administrators to monitor the network nodes and implement the proper operation.
41.1 snmp-server Description
The snmp-server command is used to enable the SNMP function. By default, it is disabled. To return to the default configuration, please use no snmp-server command.
Syntax snmp-server
no snmp-server
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Enable the SNMP function:
T2600G-28TS(config)# snmp-server
41.2 snmp-server view Description
The snmp-server view command is used to add View. To delete the corresponding View, please use no snmp-server view command. The OID (Object Identifier) of the SNMP packets is used to describe the managed objects of the switch, and the MIB (Management Information Base) is the set of the OIDs. The SNMP View is created for the SNMP management station to manage MIB objects.
Syntax snmp-server view name mib-oid { include | exclude }
no snmp-server view name mib-oid
377
Parameter name —— The entry name of View, ranging from 1 to 16 characters. Each View includes several entries with the same name.
mib-oid —— MIB Object ID. It is the Object Identifier (OID) for the entry of View, ranging from 1 to 61 characters.
include | exclude —— View Type, with include and exclude options. They represent the view entry can/cannot be managed by the SNMP management station individually.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Add a View named view1, configuring the OID as 1.3.6.1.6.3.20, and this OID can be managed by the SNMP management station:
T2600G-28TS(config)# snmp-server view view1 1.3.6.1.6.3.20 include
41.3 snmp-server group Description
The snmp-server group command is used to manage and configure the SNMP group. To delete the corresponding SNMP group, please use no snmp-server group command. SNMP v3 provides the VACM (View-based Access Control Model) and USM (User-Based Security Model) mechanisms for authentication. The users in the SNMP Group can manage the device via the Read View, Write View and Notify View. And the authentication mode and the privacy mode guarantee the high security for the communication between the management station and the managed device.
Syntax
snmp-server group name [ smode { v1 | v2c | v3 }] [ slev { noAuthNoPriv | authNoPriv | authPriv }] [ read read-view ] [ write write-view ] [ notify notify-view ]
no snmp-server group name smode { v1 | v2c | v3 } slev { noAuthNoPriv | authNoPriv | authPriv }
378
Parameter name ——The SNMP Group name, ranging from 1 to 16 characters. The Group Name, Security Model and Security Level compose the identifier of the SNMP Group. These three items of the Users in one group should be the same.
smode —— Security Model, with v1, v2c and v3 options. They represent SNMP v1, SNMP v2c and SNMP v3.
slev —— The Security Level of SNMP v3 Group. There are three options, including noAuthNoPriv (no authorization and no encryption), authNoPriv (authorization and no encryption) and authPriv (authorization and encryption). By default, the Security Level is noAuthNoPriv. There is no need to configure this in SNMP v1 Mode and SNMP v2c Mode.
read-view —— Select the View to be the Read View. The management access is restricted to read-only, and changes cannot be made to the assigned SNMP View.
write-view —— Select the View to be the Write View. The management access is writing only and changes can be made to the assigned SNMP View. The View defined both as the Read View and the Write View can be read and modified.
notify-view —— Select the View to be the Notify View. The management station can receive notification messages of the assigned SNMP view generated by the switch's SNMP agent.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Add a group, and configure the name as group 1, the Security Model as SNMP v3, the security level as authNoPriv, the management access to the assigned View viewDefault as read-write, besides the notification messages sent by View viewDefault can be received by Management station:
T2600G-28TS(config)# snmp-server group group1 smode v3 slev
authNoPriv read viewDefault write viewDefault notify viewDefault
Delete group 1:
T2600G-28TS(config)# no snmp-server group group1 smode v3 slev
authNoPriv
379
41.4 snmp-server user Description
The snmp-server user command is used to add User. To delete the corresponding User, please use no snmp-server user command. The User in an SNMP Group can manage the switch via the management station software. The User and its Group have the same security level and access right.
Syntax snmp-server user name { local | remote } group-name [ smode { v1 | v2c | v3 }] [ slev { noAuthNoPriv | authNoPriv | authPriv }] [ cmode { none | MD5 | SHA }] [ cpwd confirm-pwd ] [ emode { none | DES }] [ epwd encrypt-pwd ]
no snmp-server user name
Parameter name —— User Name, ranging from 1 to 16 characters.
local | remote —— User Type, with local and remote options. Local indicates that the user is connected to a local SNMP engine, while remote means that the user is connected to a remote SNMP engine.
group-name —— The Group Name of the User. The User is classified to the corresponding Group according to its Group Name, Security Model and Security Level.
smode —— The Security Model of the User, with v1, v2c and v3 options. By default, the option is v1. The Security Model of the User must be the same with that of the Group which the User belongs to.
slev —— The Security Level of SNMP v3 Group. There are three options, including noAuthNoPriv (no authorization and no encryption), authNoPriv (authorization and no encryption) and authPriv (authorization and encryption). By default, the option is “noAuthNoPriv”. The Security Level of the User must be the same with that of the Group which the User belongs to.
cmode —— The Authentication Mode of the SNMP v3 User, with none, MD5 and SHA options. None indicates no authentication method is used, MD5 indicates the port authentication is performed via HMAC-MD5 algorithm and SHA indicates the port authentication is performed via SHA (Secure Hash Algorithm). SHA authentication mode has a higher security than MD5 mode. By default, the Authentication Mode is “none”.
confirm-pwd —— Authentication Password, ranging from 1 to 16 characters. The question marks and spaces are not allowed. This password in the configuration file will be displayed in the symmetric encrypted form.
380
emode —— The Privacy Mode of the SNMP v3 User, with none and DES options. None indicates no privacy method is used, and DES indicates DES encryption method is used. By default, the Privacy Mode is “none”.
encrypt-pwd —— Privacy Password, ranging from 1 to 16 characters. The question marks and spaces are not allowed. This password in the configuration file will be displayed in the symmetric encrypted form.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Add Local User admin to Group group2, and configure the Security Model of the user as v3, the Security Level of the group as authPriv, the Authentication Mode of the user as MD5, the Authentication Password as 11111, the Privacy Mode as DES, and the Privacy Password as 22222:
T2600G-28TS(config)# snmp-server user admin local group2 smode v3
slev authPriv cmode MD5 cpwd 11111 emode DES epwd 22222
41.5 snmp-server community Description
The snmp-server community command is used to add Community. To delete the corresponding Community, please use no snmp-server community command. SNMP v1 and SNMP v2c adopt community name authentication. The community name can limit access to the SNMP agent from SNMP network management station, functioning as a password.
Syntax snmp-server community name { read-only | read-write } mib-view
no snmp-server community name
Parameter name —— Community Name, ranging from 1 to 16 characters.
read-only | read-write —— The access rights of the community, with read-only and read-write options.
mib-view —— The MIB View for the community to access.
381
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Add community public, and the community has read-write management right to View viewDefault:
T2600G-28TS(config)# snmp-server community public read-write
viewDefault
41.6 snmp-server host Description
The snmp-server host command is used to add Notification. To delete the corresponding Notification, please use no snmp-server host command.
Syntax snmp-server host ip udp-port user-name [ smode { v1 | v2c | v3 }] [ slev { noAuthNoPriv | authNoPriv | authPriv }] [ type { trap | inform }] [ retries retries ] [ timeout timeout ]
no snmp-server host ip user-name
Parameter ip —— The IP Address of the management Host. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.100 or fe80::1234.
udp-port —— UDP port, which is used to send notifications. The UDP port functions with the IP address for the notification sending. It ranges from 1 to 65535.
user-name —— The User name of the management station.
smode —— The Security Model of the management station, with v1, v2c and v3 options. By default, the option is v1.
slev —— The Security Level of SNMP v3 Group. There are three options, including noAuthNoPriv (no authorization and no encryption), authNoPriv (authorization and no encryption) and authPriv (authorization and encryption). By default, the option is “noAuthNoPriv”.
type —— The type of the notifications, with trap and inform options. Trap indicates traps are sent, while inform indicates informs are sent. The inform
382
type has a higher security than the trap type and resend and timeout need to be configured if you select this option. You can only select the trap type in Security Model v1. By default, the type of the notifications is “trap”.
retries —— The amount of times the switch retries an inform request, ranging from 1 to 255. The switch will resend the inform request if it doesn’t get the response from the management station during the Timeout interval, and it will terminate resending the inform request if the resending times reach the specified Retry times.
timeout —— The maximum time for the switch to wait for the response from the management station before resending a request, ranging from 1 to 3600 in seconds.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Add a Notification entry, and configure the IP address of the management Host as 192.168.0.146, the UDP port as 162, the User name of the management station as admin, the Security Model of the management station as v2c, the type of the notifications as inform, the maximum time for the switch to wait as 1000 seconds, and the retries time as 100:
T2600G-28TS(config)# snmp-server host 192.168.0.146 162 admin smode
v2c type inform retries 100 timeout 1000
Add a Notification entry, and configure the IP Address of the management Host as fe80::1234, the UDP port as 162, the User name of the management station as admin, the Security Model of the management station as v2c, the type of the notifications as inform, the maximum time for the switch to wait as 1000 seconds, and the retries time as 100:
T2600G-28TS(config)# snmp-server host fe80::1234 162 admin smode v2c
type inform retries 100 timeout 1000
383
41.7 snmp-server engineID Description
The snmp-server engineID command is used to configure the local and remote engineID of the switch. To restore to the default setting, please use no snmp-server engineID command.
Syntax snmp-server engineID { [ local local-engineID ] [ remote remote-engineID ] }
no snmp-server engineID
Parameter local-engineID —— Local Engine ID for local clients. The Engine ID is a unique alphanumeric string used to identify the SNMP engine on the switch. Its length ranges from 10 to 64 hexadecimal characters, which must be even number meanwhile.
remote-engineID —— Remote Engine ID for the switch. The Engine ID is a unique alphanumeric string used to identify the SNMP engine on the remote device which receives informs from the switch. Its length ranges from 10 to 64 hexadecimal characters, which must be even number meanwhile. The snmp-server engineID will be disabled if the local and remote are both not configured.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Specify the local engineID as 1234567890, and the remote engineID as abcdef123456:
T2600G-28TS(config)# snmp-server engineID local 1234567890 remote
abcdef123456
41.8 snmp-server traps snmp Description
The snmp-server traps snmp command is used to enable SNMP standard traps which include four types: linkup, linkdown, warmstart and coldstart. To
384
disable the sending of SNMP standard traps, please use no snmp-server traps snmp command.
Syntax snmp-server traps snmp [ linkup | linkdown | warmstart | coldstart | auth-failure ]
no snmp-server traps snmp [ linkup | linkdown | warmstart | coldstart | auth-failure ]
Parameter linkup —— Enable linkup trap. It is sent when port status changes from linkdown to linkup. By default, it is enabled.
linkdown ——Enable linkdown trap. It is sent when port status changes from linkup to linkdown. By default, it is enabled.
warmstart —— Enable warmstart trap. It is sent upon SNMP function reboot. By default, it is enabled.
coldstart —— Enable coldstart trap. It is sent upon switch reboot. By default, it is enabled.
auth-failure —— Enable the auth-failure trap. It is sent when a received SNMP request fails the authentication. By default, it is enabled.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Enable SNMP standard linkup trap for the switch:
T2600G-28TS(config)# snmp-server traps snmp linkup
41.9 snmp-server traps link-status Description
The snmp-server traps link-status command is used to enable SNMP link status trap for the specified port. To disable the sending of SNMP link status trap, please use no snmp-server traps link-status command.
Syntax snmp-server traps link-status
no snmp-server traps link-status
385
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin level users have access to these commands.
Example Enable SNMP link status trap for port 3:
T2600G-28TS(config)# interface gigabitEthernet 1/0/3
T2600G-28TS(config-if)# snmp-server traps link-status
41.10 snmp-server traps Description
The snmp-server traps command is used to enable SNMP extended traps. To disable the sending of SNMP extended traps, please use no snmp-server traps command.
Syntax snmp-server traps { bandwidth-control | cpu | flash | lldp remtableschange | lldp topologychange | loopback-detection | storm-control | spanning-tree | memory }
no snmp-server traps { bandwidth-control | cpu | flash | lldp remtableschange | lldp topologychange | loopback-detection | storm-control | spanning-tree | memory }
Parameter bandwidth-control —— Enable bandwidth-control trap. It is sent when the rate limit function is enabled and the bandwidth exceeds the predefined value.
cpu —— Allow CPU-related trap. It is sent when CPU usage exceeds the predefined threshold. By default, the CPU usage threshold of the switch is 80%.
flash —— Enable flash trap. It is sent when flash is modified during operations such as backup, reset, firmware upgrade, configuration import, etc.
lldp remtableschange ——A lldp RemTablesChange notification is sent when the value of lldp StatsRemTableLastChangeTime changes. It can be utilized by an NMS to trigger LLDP remote systems table maintenance polls.
386
lldp topologychange —— a notification generated by the local device to sense the change in the topology that indicates a new remote device attached to a local port, or a remote device disconnected or moved from one port to another.
loopback-detection —— Enable loopback-detection trap. It is sent when the switch detects loopback or loopback is cleared.
storm-control —— Enable storm-control trap. It is sent when the multicast or broadcast rate exceeds the predefined value.
spanning-tree —— Enable spanning-tree trap. It is sent when the port forwarding status changes or the port receives TCN packet or packet with TC fport-channel-.
memory —— Enable memory trap. It is sent when memory usage exceeds 80%.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Enable SNMP extended bandwidth-control trap for the switch:
T2600G-28TS(config)# snmp-server traps bandwidth-control
41.11 snmp-server traps ddm Description
The snmp-server traps ddm command is used to enable SNMP DDM traps. DDM function is used to monitor the status of the SFP modules inserted into the SFP ports on the switch.
To disable the sending of SNMP DDM traps, use no snmp-server traps ddm command.
Syntax snmp-server traps ddm [ temperature | voltage | bias_current | tx_power | rx_power ]
no snmp-server traps ddm [ temperature | voltage | bias_current | tx_power | rx_power ]
387
Parameter temperature —— Enable DDM Temperature trap. It is sent when the DDM temperature value exceeds the alarm threshold or warning threshold.
voltage —— Enable DDM Voltage trap. It is sent when the DDM voltage value exceeds the alarm threshold or warning threshold.
bias_current —— Enable DDM Bias Current trap. It is sent when the DDM bias current value exceeds the alarm threshold or warning threshold.
tx_power —— Enable DDM Tx Power trap. It is sent when the DDM Tx power value exceeds the alarm threshold or warning threshold.
rx_power —— Enable DDM Rx Power trap. It is sent when the DDM Rx power value exceeds the alarm threshold or warning threshold.
User guidelines The snmp-server traps ddm command without any parameter is used to enable all the types of DDM traps. And the no snmp-server traps ddm command without any parameter is used to disable all the types of DDM traps.
For more instructions about the alarm threshold or warning threshold, refer to Chapter 34 DDM Commands.
Command Mode Global Configuration Mode
Example Enable all the SNMP DDM traps for the switch:
T2500-28TC(config)# snmp-server traps ddm
41.12 snmp-server traps vlan Description
The snmp-server traps vlan command is used to enable SNMP extended VLAN-related traps which include two types: create and delete. To disable this function, please use no snmp-server traps vlan command.
Syntax snmp-server traps vlan [ create | delete ]
no snmp-server traps vlan [create | delete ]
388
Parameter create —— Enable VLAN-created trap. It is sent when new VLAN is created successfully.
delete —— Enable VLAN-deleted traps. It is sent when VLAN is deleted successfully.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Enable all SNMP extended VLAN-related traps for the switch:
T2600G-28TS(config)# snmp-server traps vlan
Enable VLAN-created trap only for the switch:
T2600G-28TS(config)# snmp-server traps vlan create
41.13 snmp-server traps security dhcp-snoop Description
The snmp-server traps security dhcp-snoop command is used to enable the illegal DHCP server trap feature. The switch will send an SNMP trap message when untrusted port receives DHCP Server packets. To disable this feature, please use no snmp-server traps security dhcp-snoop command.
Syntax snmp-server traps security dhcp-snoop
no snmp-server traps security dhcp-snoop
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Enable the illegal DHCP server trap feature for the switch:
T2600G-28TS(config)# snmp-server traps security dhcp-snoop
389
41.14 rmon history Description
The rmon history command is used to configure the history sample entry. To return to the default configuration, please use no rmon history command. RMON (Remote Monitoring), basing on SNMP architecture, functions to monitor the network. History Group is one of the commonly used RMON Groups. After a history group is configured, the switch collects network statistics information periodically, based on which the management station can monitor network effectively.
Syntax rmon history index interface gigabitEthernet port [ interval seconds ] [ owner owner-name ] [ buckets number ]
no rmon history index
Parameter index —— The index number of the entry, ranging from 1 to 12, in the format of 1-3,5.
port ——The Ethernet port number.
seconds —— The interval to take samplings from the port, ranging from 10 to 3600 in seconds. By default, it is 1800.
owner-name —— The owner of the history sample entry, ranging from 1 to 16 characters. By default, it is “monitor”.
number —— The maximum number of buckets desired for the RMON history group of statistics, ranging from 1 to 130. The default is 50 buckets.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Configure the sample port as Gi1/0/2 and the sample interval as 100 seconds for the entry 1-3:
T2600G-28TS(config)# rmon history 1-3 interface gigabitEthernet 1/0/2
interval 100 owner owner1
390
41.15 rmon event Description
The rmon event command is used to configure the entries of SNMP-RMON Event. To return to the default configuration, please use no rmon event command. Event Group, as one of the commonly used RMON Groups, is used to define RMON events. Alarms occur when an event is detected.
Syntax rmon event index [ user user-name ] [ description descript ] [ type { none | log | notify | log-notify }] [ owner owner-name ]
no rmon event index
Parameter index —— The index number of the event entry, ranging from 1 to 12. You can only select one entry for each command.
user-name —— The name of the User to which the event belongs, ranging from 1 to 16 characters. By default, it is “public”.
descript —— The description of the event, ranging from 1 to 16 characters. By default, it is empty.
type —— The event type, with none, log, notify and both options. None indicates no processing, log indicates logging the event, notify indicates sending trap messages to the management station, and both indicates logging the event and sending trap messages to the management station.
owner-name —— The owner of the event entry, ranging from 1 to 16 characters. By default, it is “monitor”.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Configure the user name of entry 1, 2, 3 and 4 as user1, the description of the event as description1, the type of event as log and the owner of the event as owner1:
T2600G-28TS(config)# rmon event 1-4 user user1 description description1
type log owner owner1
391
41.16 rmon alarm Description
The rmon alarm command is used to configure SNMP-RMON Alarm Management. To return to the default configuration, please use no rmon alarm command. Alarm Group is one of the commonly used RMON Groups. RMON alarm management allows monitoring the specific alarm variables. When the value of a monitored variable exceeds the threshold, an alarm event is generated, which triggers the switch to act in the set way.
Syntax rmon alarm index { stats-index sindex } [ alarm-variable { revbyte | revpkt | bpkt | mpkt | crc-lign | undersize | oversize | jabber | collision | 64 | 65-127 | 128-511 | 512-1023 | 1024-10240 }] [ s-type { absolute | delta} ] [ rising-threshold r-hold ] [ rising-event-index r-event] [ falling-threshold f-hold] [ falling-event-index f-event] [ a-type {rise | fall | all} ] [ owner owner-name ] [ interval interval]
no rmon alarm index
Parameter index —— The index number of the Alarm Management entry, ranging from 1 to 12, in the format of 1-3,5.
sindex —— Specify the statistics index.
alarm-variable —— The alarm variable. By default, the option is revbyte.
s-type —— Sample Type, which is the sampling method for the selected variable and comparing the value against the thresholds. There are two options, absolute and delta. Absolute indicates comparing the values directly with the thresholds at the end of the sampling interval. Delta indicates subtracting the last sampled value from the current value, and then comparing the difference in the values with the threshold. By default, the Sample Type is absolute.
r-hold —— The rising counter value that triggers the Rising Threshold alarm, ranging from 1 to 2147483647. By default, it is 100.
r-event —— Rise Event, which is the index of the corresponding event which will be triggered if the sampled value is larger than the Rising Threshold. It ranges from 1 to 12.
f-hold —— The falling counter value that triggers the Falling Threshold alarm, ranging from 1 to 2147483647. By default, it is 100.
392
f-event —— Fall Event, which is the index of the corresponding event which will be triggered if the sampled value is lower than the Falling Threshold. It ranges from 1 to 12.
a-type —— Alarm Type, with rise, fall and all options. Rise indicates that the alarm event will be triggered when the sampled value exceeds the Rising
Threshold, fall indicates that the alarm event will be triggered when the sampled value is under the Falling Threshold, and all indicates that the alarm event will be triggered either the sampled value exceeds the Rising Threshold or is under the Falling Threshold. By default, the Alarm Type is all.
owner-name —— The owner of the entry, ranging from 1 to 16 characters. By default, it is monitor.
interval —— The alarm interval time, ranging from 10 to 3600 in seconds. By default, it is 1800.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Configure rmon alarm entries 1-3 binding with statistics entry 2, the owners as owner1 and the alarm intervals as 100 seconds:
T2600G-28TS(config)#rmon alarm 1-3 stats-index 2 owner owner1 interval
100
41.17 rmon statistics Description
The rmon statistics command is used to configure the entries of SNMP-RMON statistics. To delete the corresponding entry, please use no rmon statistics command. The maximum supported entries are 1000.
Syntax rmon statistics index interface gigabitEthernet port [ owner owner-name] [ status { underCreation | valid }]
no rmon statistics index
393
Parameter index —— The index number of the statistics entry, ranging from 1 to 65535, in the format of 1-3,5.
port —— The statistics port number, in the format of 1/0/1.
owner-name —— The creator of the event entry, ranging from 1 to 16 characters. By default, it is “monitor”.
status —— The status of the statistics entry, either “underCreation” or “valid”. “underCreation” means this entry won’t take effect until it is modified to “valid”; “valid” means this entry takes effect immediately after it is created.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Configure the statistics entries 1-3 with the statistics port as 1/0/1, owner as owner1 and status as valid:
T2600G-28TS(config)#rmon statistics 1-3 interface gigabitEthernet 1/0/1
owner owner1 status valid
41.18 show snmp-server Description
The show snmp-server command is used to display SNMP configuration globally.
Syntax show snmp-server
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display SNMP configuration globally:
T2600G-28TS# show snmp-server
394
41.19 show snmp-server view Description
The show snmp-server view command is used to display the View table.
Syntax show snmp-server view
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the View table:
T2600G-28TS# show snmp-server view
41.20 show snmp-server group Description
The show snmp-server group command is used to display the Group table.
Syntax show snmp-server group
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the Group table:
T2600G-28TS# show snmp-server group
41.21 show snmp-server user Description
The show snmp-server user command is used to display the User table.
395
Syntax show snmp-server user
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the User table:
T2600G-28TS# show snmp-server user
41.22 show snmp-server community Description
The show snmp-server community command is used to display the Community table.
Syntax show snmp-server community
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the Community table:
T2600G-28TS# show snmp-server community
41.23 show snmp-server host Description
The show snmp-server host command is used to display the Host table.
Syntax show snmp-server host
Command Mode Privileged EXEC Mode and Any Configuration Mode
396
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the Host table:
T2600G-28TS# show snmp-server host
41.24 show snmp-server engineID Description
The show snmp-server engineID command is used to display the engineID of the SNMP.
Syntax show snmp-server engineID
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the engineID:
T2600G-28TS# show snmp-server engineID
41.25 show rmon history Description
The show rmon history command is used to display the configuration of the history sample entry.
Syntax show rmon history [ index ]
Parameter index —— The index number of the entry selected to display the configuration, ranging from 1 to 12, in the format of 1-3, 5. You can select more than one entry for each command. By default, the configuration of all history sample entries is displayed.
397
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the configuration of all history sample entries:
T2600G-28TS# show rmon history
41.26 show rmon event Description
The show rmon event command is used to display the configuration of SNMP-RMON Event.
Syntax show rmon event [ index ]
Parameter index —— The index number of the entry selected to display the configuration, ranging from 1 to 12, in the format of 1-3, 5. You can select more than one entry for each command. By default, the configuration of all SNMP-RMON enabled entries is displayed.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the Event configuration of entry1-4:
T2600G-28TS# show rmon event 1-4
41.27 show rmon alarm Description
The show rmon alarm command is used to display the configuration of the Alarm Management entry.
398
Syntax show rmon alarm [ index ]
Parameter index —— The index number of the entry selected to display the configuration, ranging from 1 to 12, in the format of 1-3, 5. You can select more than one entry for each command. By default, the configuration of all Alarm Management entries is displayed.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the configuration of the Alarm Management entry 1-2:
T2600G-28TS# show rmon alarm 1-2
41.28 show rmon statistics Description
The show rmon statistics command is used to display the configuration of the specified statistics entry.
Syntax show rmon statistics [ index ]
Parameter index —— The index number of the statistics entry selected to display the configuration, ranging from 1 to 65535. By default, the configuration of all statistics entries is displayed.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example Display the configuration of the statistics entry 1:
T2600G-28TS#show rmon statistics 1
399
Chapter 42 LLDP Commands
LLDP function enables network devices to advertise their own device information periodically to neighbors on the same LAN. The information of the LLDP devices in the LAN can be stored by its neighbor in a standard MIB, so it is possible for the information to be accessed by a Network Management System (NMS) using SNMP.
42.1 lldp Description
The lldp command is used to enable LLDP function. To disable the LLDP function, please use no lldp command.
Syntax lldp
no lldp
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable LLDP function globally:
T2600G-28TS(config)#lldp
42.2 lldp forward_message Description
The lldp forward_message command is used to enable the switch to forward LLDP messages when LLDP function is disabled. To disable the LLDP messages forwarding function, please use no lldp forward_message command.
Syntax lldp forward_message
no lldp forward_message
400
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the switch to forward LLDP messages when LLDP function is disabled globally:
T2600G-28TS(config)#lldp forward_message
42.3 lldp hold-multiplier Description
The lldp hold-multiplier command is used to configure the Hold Multiplier parameter. The aging time of the local information in the neighbor device is determined by the actual TTL value used in the sending LLDPDU. TTL = Hold Multiplier * Transmit Interval. To return to the default configuration, please use no lldp hold-multiplier command.
Syntax lldp hold-multiplier multiplier
no lldp hold-multiplier
Parameter multiplier —— Configure the Hold Multiplier parameter. It ranges from 2 to 10. By default, it is 4.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Specify Hold Multiplier as 5:
T2600G-28TS(config)#lldp hold-multiplier 5
401
42.4 lldp timer Description
The lldp timer command is used to configure the parameters about transmission. To return to the default configuration, please use no lldp timer command.
Syntax lldp timer { tx-interval tx-interval | tx-delay tx-delay | reinit-delay reinit-delay | notify-interval notify-interval | fast-count fast-count }
no lldp timer { tx-interval | tx-delay | reinit-delay | notify-interval | fast-count }
Parameter tx-interval —— Configure the interval for the local device to transmit LLDPDU to its neighbors. The value ranges from 5 to 32768 and the default value is 30 seconds.
tx-delay —— Configure a value from 1 to 8192 in seconds to specify the time for the local device to transmit LLDPDU to its neighbors after changes occur so as to prevent LLDPDU being sent frequently. By default, it is 2 seconds.
reinit-delay —— This parameter indicates the amount of delay from when LLDP status becomes "disable" until re-initialization will be attempted. The value ranges from 1 to 10 and the default value is 3.
notify-interval —— Specify the interval of Trap message which will be sent from local device to network management system. The value ranges from 5 to 3600 and the default value is 5 seconds.
fast-count —— When the port's LLDP state transforms from Disable (or Rx_Only) to Tx&Rx (or Tx_Only), the fast start mechanism will be enabled, that is, the transmit interval will be shorten to a second, and several LLDPDUs will be sent out (the number of LLDPDUs equals this parameter). The value ranges from 1 to 10 and the default value is 3.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Specify the Transmit Interval of LLDPDU as 45 seconds and Trap message to NMS as 120 seconds:
402
T2600G-28TS(config)#lldp timer tx-interval 45
T2600G-28TS(config)#lldp timer notify-interval 120
42.5 lldp receive Description
The lldp receive command is used to enable the designated port to receive LLDPDU. To disable the function, please use no lldp receive command.
Syntax lldp receive
no lldp receive
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable Gigabit Ethernet port 1/0/1 to receive LLDPDU:
T2600G-28TS(config)#interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)#lldp receive
42.6 lldp transmit Description
The lldp transmit command is used to enable the designated port to transmit LLDPDU. To disable the function, please use no lldp transmit command.
Syntax lldp transmit
no lldp transmit
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
403
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable Gigabit Ethernet port 1/0/1 to transmit LLDPDU:
T2600G-28TS(config)# interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)#lldp transmit
42.7 lldp snmp-trap Description
The lldp snmp-trap command is used to enable the port’s SNMP notification. If enabled, the port will notify the trap event to network management system. To disable the ports' SNMP notification, please use no lldp snmp-trap command.
Syntax lldp snmp-trap
no lldp snmp-trap
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the SNMP notification for Gigabit Ethernet port 1/0/1:
T2600G-28TS(config)#interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)#lldp snmp-trap
404
42.8 lldp tlv-select
Description The lldp tlv-select command is used to configure TLVs to be included in outgoing LLDPDU. To exclude TLVs, please use no lldp tlv-select command. By default, All TLVs are included in outgoing LLDPDU.
Syntax lldp tlv-select { [ port-description ] [ system-capability ] [ system-description ] [ system-name ] [ management-address ] [ port-vlan ] [ protocol-vlan ] [ vlan-name ] [ link-aggregation ] [ mac-phy-cfg ] [ max-frame-size ] [ power ] [ all ] }
no lldp tlv-select { [ port-description ] [ system-capability ] [ system-description ] [ system-name ] [ management-address ] [ port-vlan ] [ protocol-vlan ] [ vlan-name ] [ link-aggregation ] [ mac-phy-cfg ] [ max-frame-size ] [ power ] [ all ] }
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Exclude “management-address” and “port-vlan-id” TLVs in LLDPDU outgoing from Gigabit Ethernet port 1/0/1:
T2600G-28TS(config)# interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)# no lldp tlv-select management-address port-vlan
42.9 lldp management address
Description The lldp management address command is used to configure the port‘s management address to be included in management address TLV. The NMS uses management addresses to identify the devices. To delete the port‘s management address, please use no lldp management address command.
405
Syntax lldp management address { ip-address }
no lldp management address
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the port‘s management address as 192.168.1.100 for Gigabit Ethernet port 1/0/1:
T2600G-28TS(config)# interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)# lldp management address 192.168.0.100
42.10 lldp med-fast-count Description
The lldp med-fast-count command is used to configure the number of the LLDP-MED frames that will be sent out. When LLDP-MED fast start mechanism is activated, multiple LLDP-MED frames will be transmitted based on this parameter. The default value is 4. To return to the default configuration, please use no lldp med-fast-count command.
Syntax lldp med-fast-count count
no lldp med-fast-count
Parameter count —— Configure the Fast Start Count parameter. It ranges from 1 to 10. By default, it is 4.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
406
Example Specify Fast Start Count as 5:
T2600G-28TS(config)# lldp med-fast-count 5
42.11 lldp med-status Description
The lldp med-status command is used to enable the LLDP-MED feature for the corresponding port. After the LLDP-MED feature is enabled, the port's Admin Status will be changed to Tx&Rx. To disable the LLDP-MED feature for the corresponding port, please use no lldp med-status command.
Syntax lldp med-status
no lldp med-status
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Enable the LLDP-MED feature for port 1/0/2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# lldp med-status
42.12 lldp med-tlv-select Description
The lldp med-tlv-select command is used to configure LLDP-MED TLVs to be included in outgoing LLDPDU for the corresponding port. To exclude LLDP-MED TLVs, please use no lldp med-tlv-select command. By default, All TLVs are included in outgoing LLDPDU.
Syntax lldp med-tlv-select { [inventory-management] [location] [network-policy] [power-management] [all] }
407
no lldp med-tlv-select { [inventory-management] [location] [network-policy] [power-management] [all] }
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Exclude “network policy” and “inventory” TLVs in LLDPDU outgoing from port 1/0/2:
T2600G-28TS(config)# interface gigabitEthernet 1/0/2
T2600G-28TS(config-if)# no lldp med-tlv-select network-policy inventory-
management
42.13 lldp med-location Description
The lldp med-location command is used to configure the Location Identification TLV's content in outgoing LLDPDU of the port.
Syntax lldp med-location { emergency-number identifier | civic-address [ [ language language ] [ province-state province-state ] [ county county] [city city ] [ street street ] [ house-number house-number ] [name name ] [ postal-zipcode postal-zipcode ] [ room-number room-number ] [ post-office-box post-office-box ] [ additional additional ] [ country-code country-code ] [ what { dhcp-server | endpoint | switch } ] ] }
Parameter emergency-number —— Emergency Call Service ELIN identifier, which is used during emergency call setup to a traditional CAMA or ISDN trunk-based PSAP. The length of this field ranges from 10 to 25 characters.
civic-address —— The civic address is defined to reuse the relevant sub-fields of the DHCP option for civic Address based Location Configuration Information as specified by IETF.
408
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example Configure the civic address in the Location Identification TLV's content in outgoing LLDPDU of port 1/0/2. Configure the language as English and city as London:
T2700-28TQ (config)# interface gigabitEthernet 1/0/2
T2700-28TQ(config-if)# lldp med-location civic-address language English
city London
42.14 show lldp
Description The show lldp command is used to display the global configuration of LLDP.
Syntax show lldp
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the global configuration of LLDP:
T2600G-28TS#show lldp
409
42.15 show lldp interface
Description The show lldp interface command is used to display LLDP configuration of the corresponding port. By default, the LLDP configuration of all the ports will be displayed.
Syntax show lldp interface [ gigabitEthernet port ]
Parameters
port —— The Ethernet port number.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the LLDP configuration of Gigabit Ethernet port 1/0/1:
T2600G-28TS#show lldp interface gigabitEthernet 1/0/1
42.16 show lldp local-information interface
Description The show lldp local-information interface command is used to display the LLDP information of the corresponding port. By default, the LLDP information of all the ports will be displayed.
Syntax show lldp local-information interface [ gigabitEthernet port ]
Parameters
port —— The Ethernet port number.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
410
Example Display the LLDP information of Gigabit Ethernet port 1/0/1:
T2600G-28TS#show lldp local-information interface gigabitEthernet 1/0/1
42.17 show lldp neighbor-information interface
Description The show lldp neighbor-information interface command is used to display the neighbor information of the corresponding port. By default, the neighbor information of all the ports will be displayed.
Syntax show lldp neighbor-information interface [ gigabitEthernet port ]
Parameters
port —— The Ethernet port number.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the neighbor information of Gigabit Ethernet port 1/0/1:
T2600G-28TS#show lldp neighbor-information interface gigabitEthernet
1/0/1
42.18 show lldp traffic interface Description
The show lldp traffic interface command is used to display the LLDP statistic information between the local device and neighbor device of the corresponding port. By default, the LLDP statistic information of all the ports will be displayed.
Syntax show lldp traffic interface [ gigabitEthernet port ]
411
Parameters
port —— The Ethernet port number.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the LLDP statistic information of Gigabit Ethernet port 1/0/1:
T2600G-28TS#show lldp traffic interface gigabitEthernet 1/0/1
412
Chapter 43 sFlow Commands
Note: T2600G-18TS doesn’t support sFlow feature.
sFlow (Sampled Flow) is a technology for accurately monitoring network traffic at high speeds. The sFlow monitoring system consists of an sFlow agent (embedded in a switch or router or in a standalone probe) and a central sFlow collector. The sFlow agent is a virtual entity using sampling technology to capture traffic statistics from the device it is monitoring. The sFlow collector can be a host receiving sFlow datagrams from the sFlow agent. The sFlow feature is implemented as follows: the sFlow sampler take samples of traffic statistics and send sFlow datagrams to the sFlow agent for processing. The sFlow agent will forward sFlow datagrams to the sFlow collector for analysis. The analytic results can be displayed on the sFlow collector.
43.1 sflow address Description
The sflow address command is used to configure the sFlow agent’s IP address. To delete the configured address, please use no sflow address command.
Syntax sflow address { ipv4-addr }
no sflow address { ipv4-addr }
Parameter ipv4-addr ——The IP address of the sFlow agent. The type of the IP address should be IPv4. For example, you can set the switch’s management IP as the IP address of the sFlow agent.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Configure the sFlow agent with the IP address as 192.168.0.1:
T2600G-28TS(config)#sflow address 192.168.0.1
413
43.2 sflow enable Description
The sflow enable command is used to enable sFlow function. To disable the sFlow function, please use no sflow enable command.
Syntax sflow enable
no sflow enable
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
User Guidelines A valid agent address should be assigned to the sFlow agent embedded in the switch before you enable the sFlow function.
Example Enable sFlow function globally:
T2600G-28TS(config)#sflow enable
43.3 sflow collector collector-ID Description
The sflow collector collector-ID command is used to configure the parameters about the sFlow collector.
Syntax sflow collector collector-ID value { [descript descript ] | [ ip ip ] | [ port port ] | [ maxData maxData ] | [ timeout timeout ] }
Parameter value —— The ID of the sFlow collector you desire to configure. The value ranges from 1 to 4.
descript ——Give a description to the sFlow collector, which contains 16 characters at most.
ip ——The IP address of the sFlow collector. The type of the IP address should be IPv4, for example 192.168.0.100.
414
port ——The number of the udp port which is selected for the sFlow collector.
maxData ——Specify the maximum number of data bytes that can be sent in a single sample datagram. The value ranges from 300 to 1400 and the default value is 300 bytes.
timeout ——Specify the aging time of the sFlow collector, ranging from 0 to 2000000 seconds. When the timeout is set to 0, it means the life cycle of the collector is infinite.
Command Mode Global Configuration Mode
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Specify the ip of the sFlow collector 1 as 192.168.0.100, the port as 3000:
T2600G-28TS(config)# sflow collector collector-ID 1 ip 192.168.0.100
T2600G-28TS(config)# sflow collector collector-ID 1 port 3000
43.4 sflow sampler Description
The sflow sampler command is used to configure the parameters about the sFlow sampler.
Syntax sflow sampler { [ collector-ID value ] | [ ingRate ingress-rate ] [ egRate egress-rate ] | [ maxHeader maxHeader ] }
Parameter value —— The ID of the sFlow collector which the sFlow sampler will send sFlow datagrams to. The value ranges from 0 to 4. When the value is zero, it means no collector is selected.
ingress-rate ——Specify the ingress sampling frequency of the sFlow sampler. When a sample is taken, the value indicates how many packets to skip before the next sample is taken. The value ranges from 1024 to 65535 and the default value is 0 which means no packets will be sampled.
egress-rate ——Specify the egress sampling frequency of the sFlow sampler. When a sample is taken, the value indicates how many packets to skip before
415
the next sample is taken. The value ranges from 1024 to 65535 and the default value is 0 which means no packets will be sampled.
maxHeader ——Specify the maximum number of bytes that should be copied from a sampled packet. The value ranges from 18 to 256 and the default value is 128 bytes.
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
Only Admin and Operator level users have access to these commands.
Example Configure Gigabit Ethernet port 1 as the sFlow sampler: specify the Collector-ID as 1, the ingress rate as 1024:
T2600G-28TS(config)#interface gigabitEthernet 1/0/1
T2600G-28TS(config-if)#sflow sampler collector-ID 1
T2600G-28TS(config-if)#sflow sampler ingRate 1024
43.5 show sflow global Description
The show sflow global command is used to display the global configuration of sFlow.
Syntax show sflow global
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the global configuration of sFlow:
T2600G-28TS#show sflow global
416
43.6 show sflow collector Description
The show sflow collector command is used to display the global configuration of the sFlow collector.
Syntax show sflow collector
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the global configuration of the sFlow collector:
T2600G-28TS#show sflow collector
43.7 show sflow sampler Description
The show sflow sampler command is used to display the global configuration of the sFlow sampler.
Syntax show sflow sampler
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the global configuration of the sFlow sampler:
T2600G-28TS#show sflow sampler
417
Chapter 44 Static Routes Commands
44.1 interface vlan Description
This interface vlan command is used to create the VLAN interface. To delete the specified VLAN interface, please use the no interface vlan command.
Syntax
interface vlan { vid }
no interface vlan { vid }
Parameter
vid —— The ID of the VLAN.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create the VLAN interface 2:
T2600G-28TS(config)# interface vlan 2
44.2 interface loopback Description
This interface loopback command is used to create the loopback interface. To delete the specified loopback interface, please use the no interface loopback command.
Syntax
interface loopback { id }
no interface loopback { id }
418
Parameter
id —— The ID of the loopback interface, ranging from 1 to 64.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create the loopback interface 1:
T2600G-28TS(config)# interface loopback 1
44.3 switchport Description
This switchport command is used to switch the Layer 3 interface into the Layer 2 port. To switch the Layer 2 port into the Layer 3 routed port, please use the no switchport command.
Syntax
switchport
no switchport
Command Mode
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel)
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Switch the gigabitEthernet port 1/0/9 into the routed port:
T2600G-28TS(config)# interface gigabitEthernet 1/0/9 T2600G-28TS(config-if)# no switchport
419
44.4 interface range port-channel Description
This interface range port-channel command is used to create multiple port-channel interfaces.
Syntax
interface range port-channel port-channel-list
Parameter
port-channel-list —— The list of the port-channel interface, ranging from 1 to 14, in the format of 1-3, 5.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create the port-channel interfaces 1,3,4 and 5:
T2600G-28TS(config)# interface port-channel 1,3-5
44.5 description Description
This description command is used to add a description to the Layer 3 interface, including routed port, port-channel interface, loopback interface and VLAN interface. To clear the description of the corresponding interface, please use the no description command.
Syntax
description string
no description
Parameter
string —— Content of an interface description, ranging from 1 to 32 characters.
420
Command Mode
Interface Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Add a description system-if to the routed port 1/0/9 :
T2600G-28TS(config)# interface gigabitEthernet 1/0/9 T2600G-28TS(config-if)# no switchport T2600G-28TS(config-if)# description system-if
44.6 shutdown Description
This shutdown command is used to shut down the specified interface. The interface type include: routed port, port-channel interface, loopback interface and VLAN interface. To enable the specified interface, please use the no shutdown command.
Syntax
shutdown
no shutdown
Command Mode
Interface Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Shut down the routed port 1/0/9 :
T2600G-28TS(config)# interface gigabitEthernet 1/0/9 T2600G-28TS(config-if)# no switchport T2600G-28TS(config-if)# shutdown
421
44.7 interface port-channel Description
This interface port-channel command is used to create the port-channel interface. To delete the specified port-channel interface, please use the no interface port-channel command.
Syntax
interface port-channel { port-channel-id }
no interface port-channel { port-channel-id }
Parameter
port-channel-id —— The ID of the port-channel interface, ranging from 1 to 14.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create the port-channel interface 1:
T2600G-28TS(config)# interface port-channel 1
44.8 ip route Description
This ip route command is configure the static route. To clear the corresponding entry, please use the no ip route command.
Syntax
ip route { dest-address } { mask } { next-hop-address } [ distance ]
no ip route { dest-address } { mask } { next-hop-address }
Parameter
dest-address —— The destination IP address.
mask —— The subnet mask.
422
next-hop-address —— The address of the next-hop.
distance —— The distance metric of this route, ranging from 1 to 255. The smaller the distance is, the higher the priority is.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create a static route with the destination IP address as 192.168.2.0, the subnet mask as 255.255.255.0 and the next-hop address as 192.168.0.2:
T2600G-28TS(config)# ip route 192.168.2.0 255.255.255.0 192.168.0.2
44.9 ipv6 routing Description
This ipv6 routing command is enale the IPv6 routing feature globally. To diable IPv6 routing, please use the no ipv6 routing command.
Syntax
ipv6 routing
no ipv6 routing
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
User Guidelines For T2600G-18TS, before enable the IPv6 routing feature, you should configure the SDM template as "enterpriseV6" and save your configurations. For more information about SDM configuration, please refer to sdm prefer.
Example
Enable IPv6 routing globally:
T2600G-28TS(config)# ipv6 routing
423
44.10 ipv6 route Description
This ipv6 route command is configure the IPv6 static route. To clear the corresponding entry, please use the no ipv6 route command.
Syntax
ipv6 route { ipv6-dest-address } { next-hop-address } [ distance ]
no ipv6 route { ipv6-dest-address } { next-hop-address }
Parameter
ipv6-dest-address—— The IPv6 address of the destination network.
next-hop-address —— The IPv6 address of the next-hop.
distance —— The distance metric of this route, ranging from 1 to 255. The smaller the distance is, the higher the priority is.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create a static route with the destination network IP address as 3200::/64 and the next-hop address as 3100::1234:
T2600G-28TS(config)# ipv6 route 3200::/64 3100::1234
44.11 show interface vlan Description
The show interface vlan command is used to display the information of the specified interface VLAN.
Syntax show interface vlan vid
Parameter vid —— The VLAN ID.
424
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the information of VLAN 2:
T2600G-28TS(config)#show interface vlan 2
44.12 show ip interface Description
This show ip interface command is used to display the detailed information of the specified Layer 3 interface.
Syntax
show ip interface [ gigabitEthernet port | port-channel port-channel-id | loopback id | vlan vlan-id ]
Parameter
port —— The port number.
port-channel-id —— The ID of the port channel. Member ports in this port channel should all be routed ports.
id —— The loopback interface ID.
vlan-id —— The VLAN interface ID.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the detailed information of the VLAN interface 2:
T2600G-28TS(config)# show ip interface vlan 2
425
44.13 show ip interface brief Description
This show ip interface brief command is used to display the summary information of the Layer 3 interfaces.
Syntax
show ip interface brief
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the summary information of the Layer 3 interfaces:
T2600G-28TS(config)# show ip interface brief
44.14 show ip route Description
This show ip route command is used to display the route entries of the specified type.
Syntax
show ip route [ static | connected ]
Parameter
static | connected —— Specify the route type. If not specified, all types of route entries will be displayed.
static: The static routes.
connected: The connected routes.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
426
Example
Display the static routes:
T2600G-28TS(config)# show ip route static
44.15 show ip route specify Description
This show ip route specify command is used to display the valid routing information to the specified IP address or network segments.
Syntax
show ip route specify { ip } [ mask ] [ longer-prefixes ]
Parameter
ip —— Specify the destination IP address.
mask —— Specify the destination IP address together with the parameter ip.
longer-prefixes —— Specify the destination subnets that match the network segment determined by the ip and mask parameters.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the shortest route to 192.168.0.100:
T2600G-28TS(config)# show ip route specify 192.168.0.100
Look up the route entry with the destination as 192.168.0.0/24:
T2600G-28TS(config)# show ip route specify 192.168.0.0 255.255.255.0
Display the routes to all the subnets that belongs to 192.168.0.0/16:
T2600G-28TS(config)# show ip route specify 192.168.0.0 255.255.0.0 longer-prefixes
427
44.16 show ip route summary Description
This show ip route summary command is used to display the summary information of the route entries classified by their sources.
Syntax
show ip route summary
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the summary information of route entries:
T2600G-28TS(config)# show ip route summary
44.17 show ipv6 interface Description
This command is used to display the configured IPv6 information of the management interface, including ipv6 function status, link-local address and global address, IPv6 multicast groups etc.
Syntax
show ipv6 interface
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the IPv6 information of the management interface:
T2600G-28TS(config)# show ipv6 interface
428
44.18 show ipv6 route Description
This show ipv6 route command is used to display the IPv6 route entries of the specified type.
Syntax
show ipv6 route [ static | connected ]
Parameter
static | connected —— Specify the route type. If not specified, all types of route entries will be displayed.
static: The static routes.
connected: The connected routes.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the IPv6 static routes:
T2600G-28TS(config)# show ipv6 route static
44.19 show ipv6 route summary Description
This show ipv6 route summary command is used to display the summary information of the IPv6 route entries classified by their sources.
Syntax
show ipv6 route summary
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
429
Example
Display the summary information of IPv6 route entries:
T2600G-28TS(config)# show ipv6 route summary
430
Chapter 45 SDM Template Commands
This chapter describes how to configure the Switch Database Management (SDM) templates to allocate hardware resources on the switch for different uses.
45.1 sdm prefer Description
The sdm prefer command is used to configure the SDM template. The SDM template is used to allocate system resources to best support the features being used in your application. To return to use the default template, please use the sdm prefer default command. The template change will takes effect after a reboot.
Syntax
sdm prefer { default | enterpriseV4 | enterpriseV6 }
Parameter default —— Specify the SDM template used in the switch as “default”.
enterpriseV4 —— Specify the SDM template used in the switch as “enterpriseV4”.
enterpriseV6 —— Specify the SDM template used in the switch as “enterpriseV6”.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Specify the SDM template as enterpriseV4:
T2600G-28TS(config)# sdm prefer enterpriseV4
431
45.2 show sdm prefer Description
The show sdm prefer command is used to display resource allocation of the current SDM template in use, or the SDM templates that can be used.
Syntax
show sdm prefer { used | default | enterpriseV4 | enterpriseV6 }
Parameter used —— Display the resource allocation of the template currently in use, and the template that will become active after a reboot.
default —— Display the resource allocation of the default template.
enterpriseV4 —— Display the resource allocation of the enterpriseV4 template. enterpriseV6 —— Display the resource allocation of the enterpriseV6 template.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Display the resource allocation of the template currently in use, and the template that will become active after a reboot:
T2600G-28TS(config)#show sdm prefer used
432
Chapter 46 AAA Commands
AAA stands for authentication, authorization and accounting. This feature is used to authenticate users trying to log in to the switch or trying to access the administrative level privilege.
Applicable Access Application
The authentication can be applied on the following access applications: Console, Telnet, SSH and HTTP.
Authentication Method List
A method list describes the authentication methods and their sequence to authenticate a user. The switch supports Login List for users to gain access to the switch, and Enable List for normal users to gain administrative privileges.
RADIUS/TACACS+ Server
User can configure the RADIUS/TACACS+ servers for the connection between the switch and the server.
Server Group
User can define the authentication server group with up to several servers running the same secure protocols, either RADIUS or TACACS+. Users can set these servers in a preferable order, which is called the server group list. When a user tries to access the switch, the switch will ask the first server in the server group list for authentication. If no response is received, the second server will be queried, and so on.
46.1 aaa enable Description
The aaa enable command is used to enable the AAA function globally. To disable the AAA function globally, please use the no aaa enable command. The global AAA function is disabled by default.
Syntax
aaa enable
no aaa enable
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
433
Example
Enable the AAA function globally:
T2600G-28TS(config)# aaa enable
46.2 tacacas-server host Description
The tacacs-server host command is used to configure a new TACACS+ server. To delete the specified TACACS+ server, please use no tacacs-server host command.
Syntax
tacacs-server host ip-address [ port port-id ] [ timeout time ] [ key { [ 0 ] string | 7 encryped-string } ]
no tacacs-server host ip-address
Parameter
ip-address —— Specify the IP address of the TACACS+ server.
port-id —— Specify the server’s port number for AAA. By default it is 49.
time —— Specify the time in seconds the switch waits for the server’s response before it times out. The time ranges from 1 to 9 seconds. The default is 5 seconds.
[ 0 ] string | 7 encrypted-string —— 0 and 7 are the encryption type. 0 indicates that an unencrypted key will follow. 7 indicates that a symmetric encrypted key with a fixed length will follow. By default, the encryption type is 0. “string” is the shared key for the switch and the authentication servers to exchange messages which contains 31 characters at most. The question marks and spaces are not allowed. “encrypted-string” is a symmetric encrypted key with a fixed length, which you can copy from another switch’s configuration file. The key or encrypted-key you configured here will be displayed in the encrypted form. Always configure the key as the last item of this command.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
434
User Guidelines The TACACS+ servers you configured are added in the server group “tacacs” by default.
Example
Configure a TACACS+ server with the IP address as 1.1.1.1, TCP port as 1500, timeout as 6 seconds, and the unencrypted key string as 12345.
T2600G-28TS(config)# tacacs-server host 1.1.1.1 port 1500 timeout 6 key
12345
46.3 show tacacs-server Description
This show tacacs-server command is used to display the summary information of the TACACS+ servers.
Syntax
show tacacs-server
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Display the information of all the TACACS+ servers:
T2600G-28TS(config)# show tacacs-server
46.4 radius-server host Description
The radius-server host command is used to configure a new RADIUS server. To delete the specified RADIUS server, please use no radius-server host command.
435
Syntax
radius-server host ip-address [ auth-port port-id ] [ acct-port port-id ] [ timeout time ] [ retransmit number ] [ nas-id nas-id ] [ key { [ 0 ] string | 7 encrypted-string } ]
no radius-server host ip-address
Parameter
ip-address —— Specify the IP address of the RADIUS server.
auth-port port-id —— Specify the UDP destination port for authentication requests. By default it is 1812.
acct-port port-id —— Specify the UDP destination port for accouting requests. By deault it is 1813.
time —— Specify the time in seconds the switch waits for the server’s response before it times out. The time ranges from 1 to 9 seconds. The default is 5 seconds.
number —— Specify the number of times a RADIUS request is resent to a server if the server is not responding in time. By default it is 2 times.
nas-id —— Specify the name of the NAS (Network Access Server) to be contained in RADIUS packets for identification. It ranges from 1 to 31 characters. The default value is the MAC address of the switch. Generally, the NAS indicates the switch itself.
[ 0 ] string | 7 encrypted-string —— 0 and 7 are the encryption type. 0 indicates that an unencrypted key will follow. 7 indicates that a symmetric encrypted key with a fixed length will follow. By default, the encryption type is 0. “string” is the shared key for the switch and the authentication servers to exchange messages which contains 31 characters at most. The question marks and spaces are not allowed. “encrypted-string” is a symmetric encrypted key with a fixed length, which you can copy from another switch’s configuration file. The key or encrypted-key you configured here will be displayed in the encrypted form. Always configure the key as the last item of this command.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
436
User Guidelines The RADIUS servers you configured are added in the server group “radius” by default.
Example
Configure a RADIUS server with the IP address as 1.1.1.1, authentication port as 1200, timeout as 6 seconds, retransmit times as 3, and the unencrypted key string as 12345.
T2600G-28TS(config)# radius-server host 1.1.1.1 auth-port 1200 timeout
6 retransmit 3 key 12345
46.5 show radius-server Description
This show radius-server command is used to display the summary information of the RADIUS servers.
Syntax
show radius-server
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Display the information of all the RADIUS servers:
T2600G-28TS(config)# show radius-server
46.6 aaa group Description
This aaa group command is used to create AAA server groups to group existing TACACS+/RADIUS servers for authentication. This command puts the switch in the server group subconfiguration mode.
To delete the corresponding AAA group, please use the no aaa group command.
437
Syntax
aaa group { radius | tacacs } group-name no aaa group { radius | tacacs } group-name
Parameter
radius | tacacs —— Specify the server group type as RADIUS or TACACS+.
group-name —— Specify the server group name.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Create a RADIUS server group with the name radius1:
T2600G-28TS(config)# aaa group radius radius1
46.7 server Description
This server command is used to add the existing server in the defined server group. To remove the specified server from the server group, please use the no server command.
Syntax
server ip-address no server ip-address
Parameter
ip-address —— Specify the server’s IP address.
Command Mode
Server Group Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Create the RADIUS server 1.1.1.1 to RADIUS server group “radius1”:
438
T2600G-28TS(config)# aaa group radius radius1 T2600G-28TS(aaa-group)# server 1.1.1.1
46.8 show aaa group Description
This show aaa group command is used to display the summary information of the AAA groups. All the servers in this group will be listed if you specify the group name.
Syntax
show aaa group [ group-name ]
Parameter
group-name —— Specify the server group name.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Display the information of all the server groups:
T2600G-28TS(config)# show aaa group
46.9 aaa authentication login Description
This aaa authentication login command is used to configure a login authentication method list. A method list describes the authentication methods and their sequence to authenticate a user. To delete the specified authentication method list, please use the no aaa authentication login command.
Syntax
aaa authentication login { method-list } { method1 } [ method2 ] [ method3 ] [ method4 ]
no authentication login method-list
439
Parameter
method-list —— Specify the method list name.
method1, method2, method3, method4 —— Specify the authentication methods in order. The next authentication method is tried only if the previous method does not respond, not if it fails.
The preset methods include radius, tacacs, local and none. “radius” means the RADIUS server group “radius”; “tacacs” means the RACACS+ server group “tacacs”; “local” means local username database are used; “none” means no authentication is used for login.
Users can aslo define new method with the aaa group command.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
User Guidelines By default the login authentication method list is “default” with “local” as method1.
Example
Configure a login authentication method list “list1” with the priority1 method as radius and priority2 method as local:
T2600G-28TS(config)# aaa authenticaiton login list1 radius local
46.10 aaa authentication enable Description
This aaa authentication enable command is used to configure a privilege authentication method list. A method list describes the authentication methods and their sequence to elevate a user’s privilege. To delete the specified authentication method list, please use the no aaa authentication enable command.
Syntax
aaa authentication enable { method-list } { method1 } [ method2 ] [ method3 ] [ method4 ]
no authentication enable method-list
440
Parameter
method-list —— Specify the method list name.
method1, method2, method3, method4 —— Specify the authentication methods in order. The next authentication method is tried only if the previous method does not respond, not if it fails.
The preset methods include radius, tacacs, local and none. “radius” means the RADIUS server group “radius”; “tacacs” means the RACACS+ server group “tacacs”; “local” means local username database are used; “none” means no authentication is used for privilege elevation.
Users can aslo define new method with the aaa group command.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
User Guidelines By default the enable authentication method is “default” with “none” as method1.
Example
Configure a privilege authentication method list “list2” with the priority1 method as radius and priority2 method as local:
T2600G-28TS(config)# aaa authenticaiton enable list2 radius local
46.11 aaa authentication dot1x default Description
This aaa authentication dot1x default command is used to configure an 802.1X authentication method list. A method list describes the authentication methods for users’ login in 802.1X. To delete the default authentication method list, please use the no aaa authentication dot1x default command.
Syntax
aaa authentication dot1x default { method }
no aaa authentication dot1x default
441
Parameter
method —— Specify the method name. Only RADIUS server group is supported, and the default method is server group “radius”.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the default 802.1X authentication method as “radius1”:
T2600G-28TS(config)# aaa authentication dot1x default radius1
46.12 aaa accounting dot1x default Description
This aaa accounting dot1x default command is used to configure an 802.1X accounting method list. To delete the default accounting method list, please use the no aaa accounting dot1x default command.
Syntax
aaa accounting dot1x default { method }
no aaa accounting dot1x default
Parameter
method —— Sp+ecify the method name. Only RADIUS server group is supported, and the default method is server group “radius”.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the default 802.1X accounting method as “radius1”:
T2600G-28TS(config)# aaa accounting dot1x default radius1
442
46.13 show aaa authentication Description
This show aaa authentication command is used to display the summary information of the authentication login, enable and dot1x metheod list.
Syntax
show aaa authentication [ login | enable | dot1x ]
Parameter
login | enable | dot1x —— Specify the method list type.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Display the information of all the authentication method lists:
T2600G-28TS(config)# show aaa authentication
46.14 show aaa accounting Description
This show aaa accounting command is used to display the summary information of the accounting metheod list.
Syntax
show aaa accounting [ dot1x ]
Parameter
dot1x —— Specify the method list type.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
443
Example
Display the information of the default 802.1X accounting method list:
T2600G-28TS(config)# show aaa accounting
46.15 line console Description
The line console command is used to enter the Line Configuration Mode configure the console port to which you want to apply the authentication list.
Syntax
line console { linenum }
Parameter
linenum —— The number of users allowed to login through console port. Its value is 0 in general, for the reason that console input is only active on one console port at a time.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Enter the Console port configuration mode and configure the console port 0:
T2600G-28TS(config)#line console 0
46.16 login authentication (console) Description
The login authentication command is used to apply the login authentication method list to the console port. To restore to the default authentication method list, please use the no login authentication command.
Syntax
login authentication { method-list }
no login authentication
444
Parameter
method-list —— Specify the login method list on the console port. It is “default” by default, which contains the method “local”.
Command Mode
Line Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the login authentication method list on the console port as “list1”:
T2600G-28TS(config)# line console 0
T2600G-28TS(config-line)# login authentication list1
46.17 enable authentication (console) Description
The enable authentication command is used to apply the privilege authentication method list to the console port. To restore to the default authentication method list, please use the no enable authentication command.
Syntax
enable authentication { method-list }
no enable authentication
Parameter
method-list —— Specify the enable method list on the console port. It is “default” by default, which contains the method “none”.
Command Mode
Line Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the enable authentication method list on the console port as “list2”:
445
T2600G-28TS(config)# line console 0
T2600G-28TS(config-line)# enable authentication list2
46.18 line telnet Description
The line telnet command is used to enter the Line Configuration Mode to configure the telnet terminal line to which you want to apply the authentication list.
Syntax
line telnet
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Enter the telnet terminal line configuration mode:
T2600G-28TS(config)#line telnet
46.19 login authentication (telnet) Description
The login authentication command is used to apply the login authentication method list to the telnet terminal line. To restore to the default authentication method list, please use the no login authentication command.
Syntax
login authentication { method-list }
no login authentication
Parameter
method-list —— Specify the login method list on the telnet terminal line. It is “default” by default, which contains the method “local”.
446
Command Mode
Line Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the login authentication method list on the telnet terminal line as “list1”:
T2600G-28TS(config)#line telnet
T2600G-28TS(config-line)# login authentication list1
46.20 line ssh Description
The line ssh command is used to enter the Line Configuration Mode to configure the ssh terminal line to which you want to apply the authentication list.
Syntax
line ssh
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Enter the ssh terminal line configuration mode:
T2600G-28TS(config)#line ssh
46.21 login authentication (ssh) Description
The login authentication command is used to apply the login authentication method list to the ssh terminal line. To restore to the default authentication method list, please use the no login authentication command.
447
Syntax
login authentication { method-list }
no login authentication
Parameter
method-list —— Specify the login method list on the ssh terminal line. It is “default” by default, which contains the method “local”.
Command Mode
Line Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the login authentication method list on the ssh terminal line as “list1”:
T2600G-28TS(config)# line ssh
T2600G-28TS(config-line)# login authentication list1
46.22 enable authentication (telnet) Description
The enable authentication command is used to apply the privilege authentication method list to the telnet terminal line. To restore to the default authentication method list, please use the no enable authentication command.
Syntax
enable authentication { method-list }
no enable authentication
Parameter
method-list —— Specify the enable method list on the telnet terminal line. It is “default” by default, which contains the method “none”.
Command Mode
Line Configuration Mode
448
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the enable authentication method list on the telnet terminal line as “list2”:
T2600G-28TS(config)#line telnet
T2600G-28TS(config-line)# enable authentication list2
46.23 enable authentication (ssh) Description
The enable authentication command is used to apply the privilege authentication method list to the ssh terminal line. To restore to the default authentication method list, please use the no enable authentication command.
Syntax
enable authentication { method-list }
no enable authentication
Parameter
method-list —— Specify the enable method list on the ssh terminal line. It is “default” by default, which contains the method “none”.
Command Mode
Line Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the enable authentication method list on the ssh terminal line as “list2”:
T2600G-28TS(config)# line ssh
T2600G-28TS(config-line)# enable authentication list2
449
46.24 ip http login authentication Description
The ip http login authentication command is used to apply the login authentication method list to users accessing through HTTP. To restore to the default authentication method list, please use the no ip http login authentication command.
Syntax
ip http login authentication { method-list }
no ip http login authentication
Parameter
method-list —— Specify the login method list on the HTTP access. It is “default” by default, which contains the method “local”.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the login authentication method list on the HTTP access as “list1”:
T2600G-28TS(config)# ip http login authentication list1
46.25 ip http enable authentication Description
The ip http enable authentication command is used to apply the privilege authentication method list to users accessing through HTTP. To restore to the default authentication method list, please use the no ip http enable authentication command.
Syntax
ip http enable authentication { method-list }
no ip http enable authentication
450
Parameter
method-list —— Specify the enable method list on the HTTP access. It is “default” by default, which contains the method “none”.
Command Mode
Line Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Configure the enable authentication method list on the HTTP access as “list2”:
T2600G-28TS(config)# ip http enable authentication list2
46.26 show aaa global Description
This show aaa global command is used to display global status of AAA function and the login/enable method lists of different application modules: console, telnet, ssh and HTTP.
Syntax
show aaa global
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin level users have access to these commands.
Example
Display the AAA function’s global status and each application’s method list:
T2600G-28TS(config)# show aaa global
451
Chapter 47 DHCP Server Commands
DHCP (Dynamic Host Configuration Protocol) is a network configuration protocol for hosts on TCP/IP networks, and it provides a framework for distributing configuration information to hosts. DHCP server assigns IP addresses from specified address pools on a switch or router to DHCP clients and manages them.
47.1 service dhcp server Description
The service dhcp server command is used to enable DHCP service globally. To disable DHCP server service, please use no service dhcp server command.
Syntax
service dhcp server no service dhcp server
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable DHCP server service globally:
T2600G-28TS(config)# service dhcp server
47.2 ip dhcp server extend-option capwap-ac-ip Description
The ip dhcp server extend-option capwap-ac-ip command is used to configure the IP address of the remote DHCP server. To delete the remote DHCP server’s IP address, please use no ip dhcp server extend-option capwap-ac-ip command.
Syntax
ip dhcp server extend-option capwap-ac-ip ip-address no ip dhcp server extend-option capwap-ac-ip
452
Parameter
ip-address —— Specify the IP address of the remote server.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Set the remote DHCP server’s IP address as 192.168.3.1:
T2600G-28TS(config)# ip dhcp server extend-option capwap-ac-ip
192.168.3.1
47.3 ip dhcp server extend-option vendor-class-id Description
The ip dhcp server extend-option vendor-class-id command is used to configure the class ID of the packets from DHCP server in a different network segment. To delete the class ID settings, please use no ip dhcp server extend-option vendor-class-id command.
Syntax
ip dhcp server extend-option vendor-class-id class-id no ip dhcp server extend-option vendor-class-id
Parameter
class-id —— Specify the class ID of the DHCP packets from another network segment.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Set the class ID of the DHCP packets from another network segment as 34:
T2600G-28TS(config)# ip dhcp server extend-option vendor-class-id 34
453
47.4 ip dhcp server exclude-address Description
The ip dhcp server exclude-address command is used to specify the reserved IP addresses which are forbidden to allocate, such as the gateway address, the network segment broadcast address, the server address etc. To delete the reserved IP addresses, please use no ip dhcp server exclude-address command.
Syntax
ip dhcp server exclude-address start-ip-address end-ip-address no ip dhcp server exclude-address start-ip-addr end-ip-address
Parameter
start-ip-address —— Specify the start IP address of the reserved IP pool. end-ip-address —— Specify the end IP address of the reserved IP pool. Only one IP address will be reserved if the end IP address and the start IP address are the same.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Set the reserved IP addresses from 192.168.1.1 to 192.168.1.9:
T2600G-28TS(config)# ip dhcp server exclude-address 192.168.1.1
192.168.1.9
47.5 ip dhcp server pool Description
The ip dhcp server pool command is used to create the address pool of DHCP Server and enter the dhcp configuration mode. To delete the address pool, please use no ip dhcp server pool command.
Syntax
ip dhcp server pool pool-name no ip dhcp server pool pool-name
454
Parameter
pool-name —— Specify the address pool name, ranging from 1 to 8 characters.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Create the address pool of name POOL1:
T2600G-28TS(config)# ip dhcp server pool POOL1
47.6 ip dhcp server ping timeout Description
The ip dhcp server ping timeout command is used to specify the timeout of PING process. To resume the default value, please use no ip dhcp server ping timeout command.
Syntax
ip dhcp server ping timeout value no ip dhcp server ping timeout
Parameter
value —— Specify the timeout value, ranging from 100 to 10000ms. The default value is 100ms.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Set the timeout of PING as 200ms:
T2600G-28TS(config)# ip dhcp server ping timeout 200
455
47.7 ip dhcp server ping packets Description
The ip dhcp server ping packets command is used to specify the number of PING packets sent. If this value is set to 0, the PING process will be disabled. To resume the default value, please use no ip dhcp server ping packets command.
Syntax
ip dhcp server ping packets num
Parameter
num —— Specify the PING packets’ number, ranging from 0 to 10. By default it’s 1.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the PING packets’ number as 2:
T2600G-28TS(config)# ip dhcp server ping packets 2
47.8 network Description
The network command is used to specify the address and subnet of the network pool.
Syntax
network network-address subnet-mask
Parameter
network-address —— Specify the network address of the pool, with the format A.B.C.D. All the IP addresses in the same subnet are allocatable except the reserved addresses and specific addresses. subnet-mask —— Specify the subnet mask of the pool, with the format A.B.C.D.
456
Command Mode
DHCP Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the address pool “product” as 192.168.1.0 255.255.255.0:
T2600G-28TS(config)# ip dhcp server pool product
T2600G-28TS(config-dhcp)# network 192.168.1.0 255.255.255.0
47.9 lease Description
The lease command is used to specify the lease time of the address pool.
Syntax
lease lease-time
Parameter
lease-time —— Specify the lease time of the pool, ranging from 1 to 2880 minutes. The default value is 120 minutes.
Command Mode
DHCP Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the lease time of address pool “product” as 10 minutes:
T2600G-28TS(config)# ip dhcp server pool product
T2600G-28TS(config-dhcp)# lease 10
457
47.10 address hardware-address Description
The address hardware-address command is used to reserve the static address bound with hardware address in the address pool. To delete the binding, please use no address hardware-address.
Syntax
address ip-address hardware-address hardware-address hardware-type { ethernet | ieee802 } no address ip-address
Parameter
ip-address —— Specify the static binding IP address. hardware-address —— Specify the hardware address, in the format XX:XX:XX:XX:XX:XX. ethernet | ieee802 —— Specify the hardware type.
Command Mode
DHCP Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Reserve the IP address 192.168.0.10 in the address pool “product” for the device with the MAC address as 5e:4c:a6:31:24:01 and the hardware type as ethernet:
T2600G-28TS(config)# ip dhcp server pool product
T2600G-28TS(config-dhcp)# address 192.168.0.10 hardware-address
5e:4c:a6:31:24:01 hardware-type ethernet
47.11 address client-identifier Description
The address client-identifier command is used to specify the static address bound with client ID in the address pool. To delete the binding, please use no address command.
458
Syntax
address ip-address client-identifier client-id [ascii] no address ip-address
Parameter
ip-address —— Specify the static binding IP address. client-id —— Specify the client ID, in the format of hex value. ascii —— The client ID is entered with ascii characters.
Command Mode
DHCP Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Reserve the IP address 192.168.0.10 in the address pool “product” for the device with the client ID as abc in ascii:
T2600G-28TS(config)# ip dhcp pool product
T2600G-28TS(dhcp-config)# address 192.168.0.10 client-identifier abc
ascii
47.12 default-gateway Description
The default-gateway command is used to specify the default gateway of the address pool. To delete the configuration, please use no default-gateway.
Syntax
default-gateway gateway-list no default-gateway
Parameter
gateway-list —— Specify the gateway list, with the format of A.B.C.D,E.F.G.H. At most 8 gateways can be configured, separated by comma.
Command Mode
DHCP Configuration Mode
459
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the address pool product’s default gateways as 192.168.0.1 and 192.168.1.1:
T2600G-28TS(config)# ip dhcp server pool product
T2600G-28TS(dhcp-config)# default-gateway 192.168.0.1,192.168.1.1
47.13 dns-server Description
The dns-server command is used to specify the DNS server of the address pool. To delete this configuration, please use no dns-server command.
Syntax
dns-server dns-list no dns-server
Parameter
dns-list —— Specify the DNS server list, with the format of A.B.C.D,E.F.G.H. At most 8 DNS servers can be configured, separated by comma.
Command Mode
DHCP Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the address pool’s DNS servers as 192.168.0.1 and 192.168.1.1:
T2600G-28TS(config)# ip dhcp server pool product
T2600G-28TS(config-dhcp)# dns-server 192.168.0.1,192.168.1.1
460
47.14 netbios-name-server Description
The netbios-name-server command is used to specify the Netbios server’s IP address. To delete the Netbios servers, please use no netbios-name-server command.
Syntax
netbios-name-server NBNS-list no netbios-name-server
Parameter
NBNS-list —— Specify the Netbios server list, with the format of A.B.C.D,E.F.G.H. At most 8 Netbios servers can be configured, separated by comma.
Command Mode
DHCP Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the address pool’s Netbios servers as 192.168.0.1 and 192.168.1.1:
T2600G-28TS(config)# ip dhcp server pool product
T2600G-28TS(config-dhcp)# netbios-name-server 192.168.0.1,192.168.1.1
47.15 netbios-node-type Description
The netbios-node-type command is used to specify the Netbios server’s node type. To delete the node type setttings, please use no netbios-node-type command.
Syntax
netbios-node-type type no netbios-node-type
Parameter
type —— Specify the node type as b-node, h-node, m-node or p-node.
461
Command Mode
DHCP Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the address pool’s Netbios server type as b-node:
T2600G-28TS(config)# ip dhcp server pool product
T2600G-28TS(config-dhcp)# netbios-node-type b-node
47.16 next-server Description
The next-server command is used to specify the next DHCP server’s address during the DHCP boot process. To delete the next server, please use no next-server command.
Syntax
next-server ip-address next-server
Parameter
ip-address —— Specify the IP address of the next server.
Command Mode
DHCP Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the next server’s IP address as 192.168.2.1:
T2600G-28TS(config)# ip dhcp server pool product
T2600G-28TS(config-dhcp)# next-server 192.168.2.1
462
47.17 domain-name Description
The domain-name command is used to specify the domain name for the DHCP client. To delete the domain name, please use no domain-name command.
Syntax
domain-name domainname no domain-name
Parameter
domainname —— Specify the domain name for the DHCP client.
Command Mode
DHCP Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the DHCP client’s domain name as edu:
T2600G-28TS(config)# ip dhcp server pool product
T2600G-28TS(config-dhcp)# domain-name edu
47.18 bootfile Description
The bootfilecommand is used to specify the name of the DHCP client’s bootfile. To delete the bootfile, please use no bootfile command.
Syntax
bootfile file-name no bootfile
Parameter
file-name —— Specify the name of the DHCP client’s bootfile.
Command Mode
DHCP Configuration Mode
463
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the name of the DHCP client’s bootfile as boot1:
T2600G-28TS(config)# ip dhcp server pool product
T2600G-28TS(config-dhcp)# bootfile boot1
47.19 show ip dhcp server status Description
The show ip dhcp server status command is used to display the status of the DHCP service.
Syntax
show ip dhcp server status
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the status of DHCP service:
T2600G-28TS(config)# show ip dhcp server status
47.20 show ip dhcp server statistics Description
The show ip dhcp server statistics command is used to display the DHCP packets received and sent by DHCP server.
Syntax
show ip dhcp server statistics
Command Mode
Privileged EXEC Mode and Any Configuration Mode
464
Privilege Requirement
None.
Example
Display the statistics of DHCP packets received and sent by the DHCP server:
T2600G-28TS(config)# show ip dhcp server statistics
47.21 show ip dhcp server extend-option Description
The show ip dhcp server extend-option command is used to display the configuration of the remote DCHP servers.
Syntax
show ip dhcp server extend-option
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configurations of the remote DCHP servers:
T2600G-28TS(config)# show ip dhcp server extend-option
47.22 show ip dhcp server pool Description
The show ip dhcp server pool command is used to display the configuration of the address pool.
Syntax
show ip dhcp server pool
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
465
Example
Display the configured address pool:
T2600G-28TS(config)# show ip dhcp server pool
47.23 show ip dhcp server excluded-address Description
The show ip dhcp server excluded-address command is used to display the configuration of reserved addresses.
Syntax
show ip dhcp server excluded-address
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configured reserved addresses:
T2600G-28TS(config)# show ip dhcp server excluded-address
47.24 show ip dhcp server manual-binding Description
The show ip dhcp server manual-binding command is used to display the configuration of static binding address.
Syntax
show ip dhcp server manual-binding
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the configured static binding address:
466
T2600G-28TS(config)# show ip dhcp server manual-binding
47.25 show ip dhcp server binding Description
The show ip dhcp server binding command is used to display the binding entries.
Syntax
show ip dhcp server binding [ ip ip-address ]
Parameter
ip-address —— Specify the binding IP address.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example
Display the address binding entries:
T2600G-28TS(config)# show ip dhcp server binding
47.26 clear ip dhcp server statistics Description
The clear ip dhcp server statistics command is used to clear the statistics information of DHCP packets.
Syntax
clear ip dhcp server statistics
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
467
Example
Clear the packet statistics:
T2600G-28TS(config)# clear ip dhcp server statistics
47.27 clear ip dhcp server binding Description
The clear ip dhcp server binding command is used to clear the binding information.
Syntax
clear ip dhcp server binding [ ip-address ]
Parameter
ip-address —— Specify the binding IP address.
Command Mode
Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Clear all the binding addresses:
T2600G-28TS(config)# clear ip dhcp server binding
468
Chapter 48 DHCP Relay Commands
A DHCP Relay is a Layer 3 device that forwards DHCP packets between clients and servers. DHCP Relay forward requests and replies between clients and servers when they are not on the same physical subnet.
48.1 service dhcp relay Description
The service dhcp relay command is used to enable DHCP Relay function globally. To disable DHCP Relay function, please use no service dhcp relay command.
Syntax
service dhcp relay no service dhcp relay
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable DHCP Relay function globally:
T2600G-28TS(config)# service dhcp relay
48.2 ip helper-address Description
The ip helper-address command is used to add DHCP Server address to the Layer 3 interface. To delete the server address, please use no ip helper-address command.
Syntax
ip helper-address ip-address no ip helper-address [ ip-address ]
469
Parameter
ip-address —— DHCP Server address.
Command Mode
Interface Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Add DHCP Server address 192.168.2.1 to interface VLAN 1:
T2600G-28TS(config)# interface vlan 1
T2600G-28TS(config-if)# ip helper-address 192.168.2.1
48.3 ip dhcp relay information Description
The ip dhcp relay information command is used to enable option 82 support in DHCP Relay. To disable this function, please use no ip dhcp relay information command.
Syntax
ip dhcp relay information no ip dhcp relay information
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable option 82 support in DHCP Relay:
T2600G-28TS(config)# ip dhcp relay information
470
48.4 ip dhcp relay information policy Description
The ip dhcp relay information policy command is used to specify the operation for the Option 82 field of the DHCP request packets from the Host. To restore to the default option, please use no ip dhcp relay information policy command.
Syntax
ip dhcp relay information policy { drop | keep | replace } no ip dhcp relay information policy
Parameter
drop | keep | replace ——The operations for Option 82 field of the DHCP request packets from the Host. The default operation is keep. drop: Discard the packet with the Option 82 field. keep: Keep the Option 82 field in the packet. replace: Replace the option 82 field with the system option defined by the switch.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the option 82 policy as replace to replace the Option 82 field with the local parameter on receiving the DHCP request packet:
T2600G-28TS(config)# ip dhcp relay information policy replace
48.5 ip dhcp relay information format Description
The ip dhcp relay information format command is used to select the format of option 82 sub-option value field. To restore to the default option, please use no ip dhcp relay information format command.
Syntax
ip dhcp relay information format { normal | private }
471
no ip dhcp relay information format
Parameter
normal | private —— The format type of option 82 sub-option value field.
normal: Indicates that the format of sub-option value field is TLV (type-length-value).
private: Indicates that the format of sub-option value field is the value you configure for the related sub-option.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Select the format of option 82 sub-option value field as TLV (type-length-value):
T2600G-28TS(config)#ip dhcp relay information format normal
48.6 ip dhcp relay information custom Description
The ip dhcp relay information custom command is used to enable the switch to customize the option 82 field. To disable this function, please use no ip dhcp relay information custom command.
Syntax
ip dhcp relay information custom no ip dhcp relay information custom
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Enable the switch to customize the option 82 field:
472
T2600G-28TS(config)# ip dhcp relay information custom
48.7 ip dhcp relay information circuit-id Description
The ip dhcp relay information circuit-id command is used to specify the custom circuit ID when option 82 customization is enabled. To clear the circuit ID, please use no ip dhcp relay information circuit-id command.
Syntax
ip dhcp relay information circuit-id circuitID no ip dhcp relay information circuit-id
Parameter
circuitID —— Specify the circuit ID, ranging from 1 to 64 characters.
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the circuit ID as “TP-Link”:
T2600G-28TS(config)# ip dhcp relay information circuit-id TP-Link
48.8 ip dhcp relay information remote-id Description
The ip dhcp relay information remote-id command is used to specify the custom remote ID when option 82 customization is enabled. To clear the remote ID, please use no ip dhcp relay information remote-id command.
Syntax
ip dhcp relay information remote-id remoteID no ip dhcp relay information remote-id
Parameter
remoteID —— Specify the remote ID, ranging from 1 to 64 characters.
473
Command Mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Specify the remote ID as “TP-Link”:
T2600G-28TS(config)# ip dhcp relay information remote-id TP-Link
48.9 ip dhcp relay default-interface
Note: T2600G-28MPS doesn’t support this command.
Description
The ip dhcp relay default-interface command is used to configure default relay agent interface. When the switch works at DHCP VLAN Relay mode and there is no IP interface in the VLAN, the switch uses the IP of default relay agent interface to fill in the relay agent IP address field of DHCP packets. To delete the default relay agent interface use no ip dhcp relay default-interface.
Syntax
ip dhcp relay default-interface no ip dhcp relay default-interface
Command mode
Interface Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Configure interface VLAN 1 as the default relay agent interface:
T2600G-28TS(config)# interface vlan 1
T2600G-28TS(config-if)# ip dhcp relay default-interface
474
48.10 ip dhcp relay vlan Description
The ip dhcp relay vlan command is used to add DHCP server address to specified VLAN. If there is an IP interface in the VLAN and it has configured a DHCP server address at the interface level, then the configuration at the interface level has higher priority. In this case, the DHCP server configured on the VLAN will not be used to forward the DHCP packets. To delete the DHCP server address use no ip dhcp relay vlan.
Syntax
ip dhcp relay vlan vid helper-address ip-address no ip dhcp relay vlan vid helper-address [ ip-address ]
Parameter
vid —— VLAN ID.
ip-address —— DHCP Server address.
Command mode
Global Configuration Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these commands.
Example
Add DHCP server address 192.168.2.1 to VLAN 1:
T2600G-28TS(config)# ip dhcp relay vlan 1 helper-address 192.168.2.1
48.11 show ip dhcp relay Description
The show ip dhcp relay command is used to display the global status and Option 82 configuration of DHCP Relay.
Syntax
show ip dhcp relay
Command Mode
Privileged EXEC Mode and Any Configuration Mode
475
Privilege Requirement
None.
Example
Display the configuration of DHCP Relay:
T2600G-28TS(config)# show ip dhcp relay
476
Chapter 49 PoE Commands
Note: Only T2600G-28MPS supports PoE function.
PoE (Power over Ethernet) technology describes a system to transmit electrical power along with data to remote devices over standard twisted-pair cable in an Ethernet network. It is especially useful for supplying power to IP telephones, wireless LAN access points, cameras and so on.
49.1 power inline consumption (global) Description
The power inline consumption command is used to configure the max power the PoE switch can supply globally.
Syntax power inline consumption power-limit
Parameter power-limit ——The max power the PoE switch can supply, ranging from 1 to 384w. By default, the value is 384.
Command Mode Global Configuration Mode
Privilege Requirement
None.
Example Configure the max power the PoE switch can supply as 160w:
T2600G-28MPS(config)# power inline consumption 160
49.2 power inline disconnect-method Description
The power inline disconnect-method command is used to offset the power limit being exceeded and keep the switch system using power at a usable level.
477
Syntax power inline disconnect-method {deny-next-port|deny-low-priority}
Parameter deny-next-port —— When the supply power exceeds the power limit, the PD linked to the next port will be disconnected.
deny-low priority —— When the supply power exceeds the power limit, the PD linked to the port with lower priority will be disconnected.
Command Mode Global Configuration Mode
Privilege Requirement
None.
Example Configure the power disconnect method as deny-next-port:
T2600G-28MPS(config)# power inline disconnect-method deny-next-port
49.3 power profile Description
The power profile command is used to create a PoE profile for the switch. To delete the configured PoE profile configuration, please use no power profile command. PoE Profile is a short cut for the configuration of the PoE port. In a PoE profile, the PoE status, PoE priority and power limit are configured. You can specify a PoE profile for each PoE port individually.
Syntax power profile name [supply {enable | disable} [priority {low | middle | high} [consumption { power-limit | auto | class1 | class2 | class3 | class4 } ] ] ]
no power profile name
Parameter name —— The PoE profile name, ranging from 1 to 16 characters. If the name being assigned contains spaces then put it inside double quotes.
supply —— The PoE status of the port in the profile. By default, the PoE status is “enable”.
priority —— The PoE priority of the port in the profile. The priority levels include “high”, “middle” and “low” in descending order. When the supply power exceeds the system power limit, the PD linked to the port with lower
478
priority will be disconnected. By default, the PoE priority is “low”.
consumption —— The max power the port in the profile can supply, with five options: “power-limit”, “auto”, ”class1”, “class2”, “class3” and “class4”. “Power-limit” indicates you can manually enter a value ranging from 1 to 300. The value is in the unit of 0.1 watt. For instance, if you want to configure the max power as 5w, you should enter 50. “Auto” indicates the value is assigned automatically by the PoE switch. “Class1” represents 4w. “Class2” represents 7w. “Class3” represents 15.4w. “Class4” represents 30w.
Command Mode Global Configuration Mode
Privilege Requirement
None.
Example Create a PoE profile named “IP Camera” whose PoE status is “enable”, PoE priority is “low” and the power limit is “5w”:
T2600G-28MPS(config)# power profile “IP Camera” supply enable
priority low consumption 50
49.4 power time-range Description
The power time-range command is used to create PoE time-range for the switch and enter Power Time-range Create Configuration Mode. After a PoE time-range is created, you need to specify the date and time which has three mode options available: absolute, periodic and holiday. A PoE time-range can implement multiple time-ranges simultaneously as long as they do not conflict with each other. To delete the corresponding PoE time-range configuration, please use no power time-range command. The PoE time-range determines the power supply time of the switch. You can specify a PoE time-range for each PoE port individually.
Syntax power time-range name
no power time-range name
Parameter name —— The PoE time-range name, ranging from 1 to 16 characters.
479
Command Mode Global Configuration Mode
Privilege Requirement
None.
Example Create a PoE time-range named “tRange1” for the switch:
T2600G-28MPS(config)# power time-range tRange1
49.5 power holiday Description
The power holiday command is used to create PoE holiday for the switch. To delete the corresponding PoE holiday configuration, please use no power holiday command.
Syntax power holiday name start-date start-date end-date end-date
no power holiday name
Parameter name —— The PoE holiday name, ranging from 1 to 16 characters.
start-date —— The start date of the PoE holiday, in the format of MM/DD, for instance, 05/01.
end-date ——The end date of the PoE holiday, in the format of MM/DD, for instance, 05/01.
Command Mode
Global Configuration Mode
Privilege Requirement
None.
Example Create a PoE holiday named “National Day”, and configure the start date as October 1st and the end date as October 3rd:
T2600G-28MPS(config)# power holiday NationalDay start-date 10/01
end-date 10/03
480
49.6 absolute Description
The absolute command is used to create an absolute mode time-range for the PoE time-range of the switch. The switch will supply power when the specified absolute time occurs. To delete the corresponding absolute mode time-range configuration, please use no absolute command.
Syntax absolute start start-date end end-date
no absolute
Parameter start-date —— The start date in Absoluteness Mode, in the format of MM/DD/YYYY.
end-date —— The end date in Absoluteness Mode, in the format of MM/DD/YYYY.
Command Mode Power Time-range Create Configuration Mode
Privilege Requirement
None.
Example Create an absolute mode time-range for the PoE of the switch and specify the date extending from May 5, 2012 through Oct. 5, 2012:
T2600G-28MPS(config)# power time-range tRange1
T2600G-28MPS(config-pwr-time-range)# absolute start 05/05/2012 end
10/05/2012
49.7 periodic Description
The periodic command is used to create a periodic mode time-range for the PoE time-range of the switch. The switch will supply power when the specified periodic time occurs. To delete the corresponding periodic mode time-range configuration, please use no periodic command.
481
Syntax periodic { [ week-date week-day ] [ time-slice1 time-slice ] [ time-slice2 time-slice ] [ time-slice3 time-slice ] [ time-slice4 time-slice ] }
no periodic [ week-date | time-slice ]
Parameter week-day —— Periodic Mode, with “1-7”, “daily”, “off-day” and “working-day” options. “1-7” should be entered in the format of 1-3, 7 which represent Monday, Tuesday, Wednesday and Sunday. “Daily” represents every day. “Off-day” represents weekend. “Working-day” represents working day.
time-slice —— Create time-slice, in the format of HH:MM-HH:MM.
Command Mode Power Time-range Create Configuration Mode
Privilege Requirement
None.
Example Configure the PoE time-range named “tRange2” as a periodic time-range and specify the date and time as 8:30 to 12:00 on weekends:
T2600G-28MPS(config)# power time-range tRange2
T2600G-28MPS(config-pwr-time-range)# periodic week-date off-day
time-slice1 08:30-12:00
49.8 holiday Description
The holiday command is used to create holiday mode time-range for the PoE time-range of the switch. When the PoE holiday which is excluded from PoE time-range occurs, the switch will not supply power.
Syntax holiday { exclude | include }
Parameter exclude —— Indicates the PoE time-range of the switch excluding the PoE holiday. When PoE holiday occurs, the switch will not supply power.
include —— Indicates the PoE time-range of the switch including the PoE holiday. It is the default option. When PoE holiday occurs, the switch will supply power.
482
Command Mode Power Time-range Create Configuration Mode
Privilege Requirement
None.
Example Create a holiday mode time-range for the PoE time-range named “tRange3” and configure PoE time-range of the switch excludes the PoE holiday:
T2600G-28MPS(config)# power time-range tRange3
T2600G-28MPS(config-pwr-time-range)# holiday exclude
49.9 power inline consumption (interface) Description
The power inline consumption command is used to configure the power limit the corresponding port can supply.
Syntax power inline consumption { power-limit | auto | class1 | class2 | class3 | class4 }
Parameter power-limit —— The max power the port in the profile can supply, with five options: “power-limit”, “auto”, ”class1”, “class2”, “class3” and “class4”. “Power-limit” indicates you can manually enter a value ranging from 1 to 300. The value is in the unit of 0.1 watt. For instance, if you want to configure the max power as 5w, you should enter 50. “Auto” indicates the value is assigned automatically by the PoE switch. “Class1” represents 4w. “Class2” represents 7w. “Class3” represents 15.4w. “Class4” represents 30w.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
None.
Example Configure the power limit as “5w” for port 2:
T2600G-28MPS(config)# interface gigabitEthernet 1/0/2
483
T2600G-28MPS(config-if)# power inline consumption 50
49.10 power inline priority Description
The power inline priority command is used to configure the PoE priority for the corresponding port
Syntax power inline priority { low | middle | high }
Parameter priority —— The PoE priority of the port. The priority levels include “high”, “middle” and “low” in descending order. When the supply power exceeds the system power limit, the PD linked to the port with lower priority will be disconnected. By default, the priority level is “low”.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
None.
Example Configure the PoE priority as “low” for port 2:
T2600G-28MPS(config)# interface gigabitEthernet 1/0/2
T2600G-28MPS(config-if)# power inline priority low
49.11 power inline supply Description
The power inline supply command is used to configure the PoE status of the corresponding port.
Syntax power inline supply { enable | disable }
Parameter enable | disable —— The PoE status of the port. By default, the PoE status is “enable”.
484
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
None.
Example Enable the PoE feature for port 2:
T2600G-28MPS(config)# interface gigabitEthernet 1/0/2
T2600G-28MPS(config-if)# power inline supply enable
49.12 power inline profile Description
The power inline profile command is used to bind a PoE profile to the corresponding port. To cancel the bind relation, please use no power inline profile command.
Syntax power inline profile name
no power inline profile
Parameter name —— The name of the PoE profile to be bound to the port. If the name being assigned contains spaces then put it inside double quotes.
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet)
Privilege Requirement
None.
Example Bind the PoE profile named “IP Camera” to port 2:
T2600G-28MPS(config)# interface gigabitEthernet 1/0/2
T2600G-28MPS(config-if)# power inline profile “IP Camera”
485
49.13 power inline time-range Description
The power inline time-range command is used to bind a PoE time-range to the corresponding port. To cancel the bind relation, please use no power inline time-range command.
Syntax power inline time-range name
no power inline time-range
Parameter name —— The name of the PoE time-range to be bound to the port.
Command Mode Interface Configuration Mode
Privilege Requirement
None.
Example Bind the PoE time-range named “tRange2" to port 2:
T2600G-28MPS(config)# interface gigabitEthernet 1/0/2
T2600G-28MPS(config-if)# power inline time-range tRange2
49.14 show power inline Description
The show power inline command is used to display the global PoE information of the system.
Syntax show power inline
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the PoE information of the system:
486
T2600G-28MPS# show power inline
49.15 show power inline configuration interface Description
The show power inline configuration interface command is used to display the PoE configuration of the certain port.
Syntax show power inline configuration interface [ gigabitEthernet port ]
Parameter port —— The Ethernet port number.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the PoE configuration of all ports:
T2600G-28MPS# show power inline configuration interface
49.16 show power inline information interface Description
The show power inline information command is used to display the PoE information of the certain port.
Syntax show power inline information interface [ gigabitEthernet port ]
Parameter port —— The Ethernet port number.
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
487
Example Display the PoE information of all ports:
T2600G-28MPS# show power inline information interface
49.17 show power profile Description
The show power profile command is used to display the defined PoE profile.
Syntax show power profile
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the defined PoE profile:
T2600G-28MPS# show power profile
49.18 show power holiday Description
The show power holiday command is used to display the defined PoE holiday.
Syntax show power holiday
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the defined PoE holiday:
T2600G-28MPS# show power holiday
488
49.19 show power time-range Description
The show power time-range command is used to display the configuration of PoE time-range.
Syntax show power time-range
Command Mode Privileged EXEC Mode and Any Configuration Mode
Privilege Requirement
None.
Example Display the configuration of PoE time-range:
T2600G-28MPS# show power time-range
489