iTach Wi-Fi to Infrared Adapter (WF2IR)iTach Ethernet to Infrared Adapter (IP2IR)

Infrared Adapter QuickStart Guide

Port 1

Port 2

Port 3

1. Connect Ethernet port to the same network as your iOS device.2. Connect Power to included power adapter.3. Using Roomie, tap Edit on the room and then Add Device. Wait up to 60 seconds and Roomie will display the unit and its IP address in the list.4. Open the IP address found via Roomie into a web browser and select the Network tab to enter the appropriate settings for your network. For the IP address setting, note that it is generally safer to reserve a DHCP address on your router for the iTach, or to use a static IP address.(continued below, right column)

Reset Sw

itchPow

er

Ethernet

Port 1

Port 2

Port 3

Reset Sw

itchPow

er

Wi-Fi

5. Click 'Apply' to save settings. Wait a minute for the unit to restart.6. Using Roomie, tap Edit on the room and then Add Device. Wait up to 60 seconds and Roomie will display the unit in the list to confirm proper setup. If the device does not show up, you may return to step 2 to restart the setup process.6. Connect included blaster cable to Port 3 if needed. Blaster cables are used when you want to address multiple devices in the same area or cabinet that can all be reached via one infrared beam. The blaster cable will only work on Port 3. Make sure that Port 3 is set to "IR Blaster" in the web interface of the iTach if you are using a blaster.7. Connect emitter cables as needed to ports 1 and 2. Cables are included with 1 emitter per port. The iTach is compatible with standard emitter cables which can be purchased with multiple emitters per port. If you did not use a blaster cable in step 6, you may connect another emitter cable to port 3 as well.8. Use the Add Device command in Roomie as in step 6 to add each device controlled via the iTach to the appropriate room making sure to specify the correct port.

1. Connect Power to included power adapter.2. Insert metal pin (thin paper clip, thumbtack) into the Reset Switch 1/8" (3mm) and hold until all LEDs start blinking in unison. This begins the setup process. Do not insert too far or use force.3. Configure a device with a web browser to connect to the Ad Hoc Wi-Fi network named "iTach…" where the ellipsis is the network address of the iTach.4. Open the address "http://169.254.1.70" using the web browser and select the Network tab to enter the appropriate settings for your Wi-Fi network such as changing the Network Type to Infrastructure and entering the name of your network (SSID). For the IP address setting, note that it is generally safer to reserve a DHCP address on your router for the iTach, or to use a static IP address.(continued below)

This document represents the complete set of instructions for using Roomie with the iTach. Other guides or applications such as iHelp are available on the Internet for generic usage of iTach units, but

Roomie users should instead follow the instructions here.

©2013 Roomie Remote, LLC

The blaster cable is affixed in front of a set of components that can be addressed by the same infrared beam. It is not attached directly to a device.

Emitter cables are affixed to the infrared receiver window of the target device. Make sure to place the adhesive side directly over the window.

1/28/13

L5 Remote AccessoryAfter plugging in the L5, when you tap 'Add Device' in Roomie, you should then see the L5 appear. If you do not, please follow these steps:

1. Run the free L5 Remote app from the App Store.2. Use L5 Remote to update the firmware of the L5 and confirm the L5 is working.3. Power off your iOS device. Unplug the L5.4. Power on your iOS device. Plug in the L5.5. Now run Roomie and the L5 should be listed in the Add Device panel ready for you to add your infrared devices.