PRODUCTIONPROGRAM

Our company is located in Sisak, 50 km south of Zagreb, the capital ofCroatia. We produce steel blooms using EAF (60 t/h) technology andseamless pipes (4" to 14") using pilger technology.CMC Sisak is part of CMC (Commercial Metals Company) headquarteredin IRVING TX, USA. CMC is a Fortune 500 company listed on the NYSE.

Since 1948 CMC Sisak has been providing customers world wide withcarbon steel seamless pipes. Through our dedication to seamless pipeproduction for more than 60 years, we have earned our position as areliable, quality-focused supplier. We know steel and we know pipes.Our products represent us - our knowledge, our skills and our values.

We pride ourselves in our long-term partnership with our customers -spanning both the 20th and 21th century. We strive to meet the specificneeds of all of our valued customers and are dedicated to our repeatbusiness model. Our customer service is second to none.Our quality system and our products are certified to the requirements ofAPI-Q1, API 5L, API 5CT, ISO 9001, ASTM, EN, DIN etc.We work with our partners to conform to any other specific industry orcustomer product or quality system specification. Consistently deliveringhigh quality pipes and blooms is the main driver of our customers'satisfaction and continuous business partnerships.

We are a globally oriented company with a sales team ready to assist you24 hours a day. Our main markets include (but are not limited to) theUnited States, Middle East, North Africa and Europe.We service a broad cross section of industries, with a primary focus on oiland gas (casing and line pipe), petrochemical, shipbuilding, mechanicaland construction sectors.

I would like to invite you to partner with the CMC Sisak team.Our Mission: Support the long term business success of our valuedcustomers.

Respectfully,Paπko Vela

President and General Manager

Dear customerThank you for your interest in CMC Sisak products.

2

Only 34 countries in the world produce Seamless pipes - Croatia is one of them.CMC Sisak d.o.o produces Seamless pipes with state of the art hot pilgerrolling technology. During our long history we defended our position inrolling technology and mechanical engineering through development.

Our Pilger rolling mill is carried out by a single pair of rolls and one mandrel.In the initial phase of production hot round steel billets are hollowed,then rolled and stretched until achieving desired length and diameter.

The rest of the work is simply a matter of threading, stamping and painting.The pipe is now ready to be loaded and shipped as a finished product.

HOT PILGERTECHNOLOGY

- PIPE ROLLING FROM RAW MATERIAL- PRODUCT QUALITY: rolled + forged product with better mechanical properties- FLEXIBILITY Easy and fast caliber changing

- OIL & GAS- PETROCHEMICAL- GEOTHERMAL- ENERGY & ENGINEERING- CONSTRUCTION

3

PILGER TECHNOLOGYADVANTAGES

INDUSTRIES:

MEDIUM MILL4'' - 7''BLOOM

STORAGE FORFINISHED PIPES

4

HYDROTESTINGANTI-CORROSIONPROTECTION

VISUAL CONTROLAND MARKING

SEAMLESS PIPE MILLPROCESS FLOW

Pipe types:CASING

ROTARYFURNACE ELONGATOR PILGER STAND DESCALINGHOT SAW NORMALISING

FURNACE

ROTARYFURNACE

ELONGATOR PILGER STAND DESCALINGHOT SAW NORMALISINGFURNACE

HEAVY MILL6'' - 14''BLOOM

COUPLINGTHREADING

PIPETHREADING

COUPLINGSPLACEMENT

ELECTRO-GALVANISATION

STORAGE FORFINISHED PIPES

5

COUPLINGSCUTTING

Pipe types:LINE-PIPESSTRUCTURALBOILER PIPES

VISUAL CONTROLAND MARKINGHYDROTESTINGSIZING MILL STRAIGHTENING NDT CUTTING AND

BEVELING

VISUAL CONTROLAND MARKING

HYDROTESTINGSIZING MILL STRAIGHTENING NDT CUTTING ANDBEVELING

Outside WALL THICKNESS mmDiameter mm 4.0 4.5 5.0 5.6 6.3 7.1 8.0 8.8 10.0 11.0 12.5 14.2 16.0 17.5 20.0101.6 9.7 10.7 11.9 13.2 14.9 16.6 18.4 20.1114.3 10.9 12.2 13.5 15.0 16.8 18.8 21.0 22.9 25.7127.0 12.1 13.6 15.0 16.8 18.8 21.0 23.5 25.7 28.9 31.5133.0 12.7 14.3 15.8 17.6 19.7 22.0 24.7 27.0 30.3 33.1 37.1139.7 13.4 15.0 16.6 18.5 20.7 23.2 26.0 28.4 32.0 34.9 39.2152.4 16.4 18.2 20.3 22.7 25.4 28.5 31.2 35.1 38.4 43.1159.0 17.1 19.0 21.2 23.7 26.6 29.8 32.6 36.7 40.1 45.2168.3 18.2 20.1 22.5 25.2 28.2 31.6 34.6 39.0 42.7 48.0 54.0177.8 21.3 23.8 26.6 29.9 33.5 36.7 41.4 45.2 51.0 57.3193.7 29.1 32.7 36.6 40.1 45.3 49.6 55.9 62.9219.1 33.1 37.1 41.6 45.6 51.6 56.5 63.7 71.8 80.1244.5 37.0 41.6 46.7 51.2 57.8 63.3 71.5 80.6 90.2267.0 41.5 45.6 51.0 55.9 63.3 69.5 78.4 84.4 88.5 93.2 99.0273.0 41.4 46.6 52.3 57.3 64.9 71.1 80.3 90.6 101.0323.9 55.5 62.3 68.4 77.4 84.9 96.0 108.0 121.0 132.0355.6 68.6 75.3 85.2 93.5 106.0 120.0 134.0 146.0 166.0

Construction and Boiler Seamless Pipes are produced with 101,6 mm-355,6 mm outside diameter or 4 -14 with according wall thickness from4,0 mm to 20,0 mm.Construction and Boiler Seamless Pipes are used in petrochemical, ship building and construction industry.

6

CONSTRUCTIONAND BOILER PIPES

Construction EN 10216- 1 P235TR1, P235TR2, P265TR1, P265TR2 -0/+15 mm 5-7 m or 10-12mConstruction EN 10210-1 S235JRH, S275JOH, S275J2H, S355J2H, S355 JOH -0/+15 mm 5-7 m or 10-12mBoiler EN 10216-2 P235GH, P265GH, P235TR2, P265TR2 -0/+15 mm 5-7 m or 10-12m

Pipe Type Norm Steel Quality Length Fix Length Standard

API 5L: Gr-B, X-42, X-46, X-52, X-60; QUALITY LEVEL PSL-1, PSL 2ASTMA 106: Gr-B, Gr-C; ASMA SA 106: Gr-B, Gr-CASTMA A 53 Gr-BASTMA A333: GR-6, Gr-1, Gr-10CSA Z 245: G-241, G-290, G-359ASTM A501

Black pipesProtected against corrosion with lacquerPlain endsBeveled ends protected with plastic capsLength - single random a double random Other lengths - Inquire

LINE PIPES

MATERIAL QUALITY DELIVERY CONDITIONS

7

Line Pipes are produced according to standard API 5L with outside diameter from 3 1 ⁄2 to 14 , and wall thickness from 0.156 to 0.750 Line pipes are used for oil, gas and water transmission.

3 1/2 90 4.000 (101.6) 0.156 (3.96) 6.41 (9.53) ... 0.188 (4.78) 7.66 (11.41) ... 0.226 (5.74) 9.12 (13.57) STD 40 0.250 (6,35) 10.02 (14.92) ... 0.281 (7.14) 11.17 (16.63) ... 0.318 (8.08) 12.52 (18.63) XS 80 4 100 4.500(114.3) 0.219 (5.56) 10.02 (14.91) ... ... 0.237 (6.02) 10.80 (16.07) STD 40 0.250 (6.35) 11.36 (16.90) ... ... 0.281 (7.14) 12.67 (18.87) ... ... 0.312 (13.97) 13.97 (20.78) ... ... 0.337( 8.56) 15.00 (22.32) XS 80 0.438 (11.13) 19.02 (28.32) ... 120 5 125 5.563 (141.3) 0.188 (4.78) 10.80 ( 16.09) ... ... 0.219 (5.56) 12.51 (18.619 ... ... 0.258 (6.55) 14.63 (21.77) STD 40 0.281 (7.14) 15.87 (23.62) ... ... 0.312 (7.92) 17.51 (26.05) ... ... 0.344 (8.78) 19.19 (28.57) ... 0.375 (9.529 20.80 (30.94) XS 80 6 150 6.625 (219.1) 0.188 (4.78) 12.94 (19.27) ... ... 0.219 (5.56) 15.00 (22.31) ... ... 0.250 (6.35) 17.04 (25.36) ... ... 0.280 (7.11) 18.99 (28.26) STD 40 0.312 (7.92) 21.06 (31.32) ... ... 0.344 (8.74) 23.10 (34.39) ... ... 0.375 (9.52) 25.05 (37.28) ... ... 0.432 (10.97) 28.60 (42.56) XS 80 8 200 8.625 (219.1) 0.250 (6.35) 22.38 (33.31) ... ... 0.277 (7.04) 24.72 (36.31) ... 30 0.312 (7.92) 27. 73 (41.24) ... ... 0.322 (8.18) 28.58 (42.55) STD 40 0.344 (8.74) 30.45 (45.34) ... ... 0.375 (9.52) 33.07 (49.20) ... ... 0.438 (11.13) 38.33(57.08) ... ... 0.500 (12.7) 43.43 (64.64) XS 80 0.594 (15.09) 51.00 (75.92) ... 100 10 250 10.750(2.730) 0.250( 6.35) 28.06 (41.75) ... 20 0.279 (7.09) 31.23 (46.49) ... 0.307 (7.80) 34.27 (51.01) ... 30 0.344 (8.749 38.27 (56.69) ... 0.365 (9.27) 40.52 (60.29) STD 40 0.438 (11.13) 48.28 (71.87) 0.594 (15.09) 64.49 (95.97) 12 300 12.750(323.8) 0.281 (7.14) 37.46 (55.75) ... ... 0.312 (7.92) 41.48 (61.69) ... ... 0.330 (8.38) 43.81 (65.18) ... 30 0.344 (8.74) 45.62 (67.90) ... ... 0.375 (9.25) 49.61 (73.78) STD ... 0.406 (10.31) 53.57(79.70) ... 40 0.438 (11.13) 57.65 (85.82) ... ... 0.500 (12.70) 65.48 (97.43) XS ... 0.562 (14.27) 73.22 (108.92) ... 60 0.688 (17.489 88.71 (132.04) ... 80 14 400 14.000 (355,6) 0.312 (7.92) 45.65 (67.90) ... 20 0.344 (8.74) 50.22 (74.76) ... ... 0.375 (9.52) 54.62 (81.25) STD 30 0.438 (11.13) 63.50 (94.55) ... 40 0.469 (11.91) 67.84 (100.94) ... ... 0.500 (12.70) 72.16 (107.39) XS ... 0.594 (15.09) 85.13 (126.71) ... 60 0.750 (19.059 106.23 (158.10) ... 80

DIMENSION PROGRAM FOR LINE PIPES

8

NPSDesignator

DNDesignator

OutsideDiameter in. (mm)

Nominal Weight(mass) per Unitlength, Plan End, lb/ft(kgm)

Nominal Wall Thickness,ln/mm

Weight Class Schedule No.

Casing is produced according to standard API 5 CT with outside diameterfrom 4 1/2 to 13 3/8 and wall thickness from 0.205 to 0.514 ,Casing is used for oil and gas industry.

H-40, K-55, J-55, N-80-1,J -55 Modified Chemistry suitable for heat treatment to:L-80, N-80Q, P 110, P 110 HC, Q 125.

STC, LTC, BTC according to standard API 5 CT

Plain endThread with coupling and protectorProtected against corrosion with lacquer

CASING

MATERIAL QUALITY

DELIVERY CONDITIONS

TYPE OF THREAD

4 1/2 4.500 9.50 0.205 4.090 3.965 9.41 10.50 0.244 4.052 3.927 10.24

11.60 0.250 4.000 3.875 11.360 13.50 0.290 3.920 3.795 13.0505 1/2 5.000 14.00 0.244 5.012 4.887 13.71 15.50 0.275 4.950 4.825 15.36 17.00 0.304 4.892 4.767 16.89 20.00 0.361 4.778 4.653 19.83 23.00 0.415 4.670 4.545 22.567 7.000 17.00 0.231 6.538 6.413 16.72 20.00 0.272 6.456 6.331 19.56

23.00 0.317 6.366 6.250e 22.65 23.00 0.317 6.366 6.241 25.69 26.00 0.362 6.276 6.151 25.69 29.00 0.408 6.184 6.059 28.75 32.00 0.453 6.094 6.000e 31.70 32.00 0.453 6.094 5.969 31.70 35.00 0.453 6.004 5.879 34.618 5/8 8.625 24.00 0.264 8.097 7.972 23.6 28.00 0.304 8.017 7.892 27.04

32.00 0.352 7.921 7.796 31.13 32.00 0.352 7.921 7.857e 31.13 36.00 0.400 7.825 7.700 35.17 40.00 0.450 7.725 7.652 39.339 5/8 9.625 32.30 0.312 9.001 8.845 31.06 36.00 0.352 8.921 8.765 34.89

40.00 0.395 8.835 8.750 38.97 40.00 0.395 8.835 8.679e 38.97 43.50 0.435 8.755 8.599 42.73 47.00 0.472 8.681 8.525 46.18 53.50 0.545 8.535 8.500 52.910 3/4 10.750 32.75 0.279 10.192 10.036 31.23 40.50 0.350 10.050 9.894 38.91

45.50 0.400 9.950 9.875 44.26 51.00 0.450 9.850 9.694 49.55 55.50 0.495 9.760 9.625e 49.55 55.50 0.495 9.760 9.604 54.26 42.00 0.333 11.084 11.000 40.6411 3/4 11.750 42.00 0.333 11.084 10.928 40.64 47.00 0.375 11.000 10.844 45.6

54.00 0.435 10.880 10.724 52.62 60.00 0.489 10.772 10.625e 58.87 60.00 0.534 10.772 10.616 58.87 65.00 0.534 10.682 10.625e 64.03 65.00 0.534 10.682 10.526 64.03 71.00 0.582 10.586 10.430 69.4813 3/8 13.375 48.00 0.330 12.715 12.559 46.02 54.50 0.380 12.615 12.459 52.79

61.00 0.430 12.515 12.359 59.50 68.00 0.480 12.415 12.259 66.17 72.00 0.514 12.347 12.250e 70.67 72.00 0.514 12.347 12.191 70.67

DIMENSION PROGRAM FOR CASING API 5 CT

9

Nominalpipe sizeInch

OutsidediameterInch

Nominallinear Masslb/ft

WallthicknessInch

InsidediameterInch

DriftdiameterInch

PlainendW pe Lb/ft

* Alternative drift capabilities will be achived in IIQ 2010, after testing

NOTES1. O.D TOLERANCE = +/- 1% FROM Nom O:D

2. MAX WALL VARIATION - EQUALSActual average OD “measured” MINUS (min. O:D “from table”) TIMES. 25 PLUS(Max ID “from table”,”MINUS Actual average ID” Measured) TIMES. 25Note: .25 is a constant used for part shift tolerance for machining

3. MAX l.D CANNOT BE OUT OF TOLERANCEmeasurments of (1) & (3) above cannot be out of tolerance at any point around the 360 circumference

DIMENSION PROGRAM FOR COUPLING STOCK

Casing Size OD (inches) Nom OD (1) Nom Wall (2) Nom Wt/Ft L.B Min O.D MAX I.D (3)4 1/2 5.000 .456 22.11. 4.950 4.0885 5.563 .504 27.23 5.507 4.5555 1/2 6.050 .500 29.64 5.989 5.0506 5/8 7.390 .594 43.11 7.316 6.1977 7.656 .575 43.48 7.579 6.5067 5/8 8.500 .700 58.31 8.415 7.1008 5/8 9.625 .750 71.09 9.528 8.1259 5/8 10.625 .750 79.09 10.518 9.12510 3/4 11.750 .750 88.11 11.632 10.25011 3/4 12.750 .750 96.12 12.622 11.25013 3/8 14.375 .750 109.14 14.231 12.875

COUPLING STOCK

1 2 lb/ft Length Diameter1 2 3 4 5 67 23.00 7.000 23.0 6 6.2507 32.00 7.000 32.0 * 6 6.0008 5/8 32.00 8.625 32.0 * 6 7.8759 5/8 40.00 9.625 40.0 12 8.7509 5/8 53.50 9.625 53.5 * 12 8.5009 5/8 58.40 9.625 58.4 * 12 8.37510 3/4 45.50 10.750 45.5 * 12 9.87510 3/4 55.50 10.750 55.5 12 9.62511 3/4 42.00 11.750 42.0 * 12 11.00011 3/4 60.00 11.750 60.0 12 10.62511 3/4 65.00 11.750 65.0 * 12 10.62513 3/4 72.00 13.375 72.0 * 12 12.250

ALTERNATIVE DRIFT SIZELabels Outside diameter In min Product linear mass Alternative drift mandrel size In min

10

STEEL MILLPROCESS FLOW

11

STEEL CLEANINGAND CONTROLING STORAGE

SLAG ANDOTHER WASTE

RECYCLING

BATCHING BASKET

Electric Arc Furnace

New 60 ton Electric Arc Furnace is a combination design unit utilizing someused components from a Melt Shop facility located at Hellenic Halyvourgia,in Aspropyrgos, Greece along with new components. The design engineeringfor the furnace reconstruction and new components was conducted by BSEof Germany. With our new EAF furnace, we are able to produce 450 000 tof quality round steel blooms annually.

Ladle Furnace Area

The ladle furnace is basically a small electric arc furnace where the furnacevessel has been replaced with the ladle full of steel. A ladle furnaceprovides a number of benefits for the modern steel making facility.

The benefits are:

1. The ladle furnace allows the steel temperature to be raised slowly andcontrolled.

2. The ladle furnace creates an area for bringing the chemistry of the heat to a perfect condition by alloy additions.

3. It allows for smooth stirring of the heat in the ladle, thereby eliminatingstratification of steel components and temperature.

4. It creates a holding area, whereby the heat of steel can be maintainedand be made ready exactly for when the continuous caster is preparedto accept the ladle of steel.

5. Allows for the sequence casting of steel on the caster.

Continuous Casting Machine Area

The final process area of the Melt Shop facility is the continuous castingmachine. The continuous caster accepts the ladle of steel and transformsthe molten steel into cast steel blooms. These blooms are round shapesranging from 210mm diameter up to 410mm diameter.They are rolled into pipe at the heavy and medium section pipe mill.

MELT SHOP TECHNOLOGY DESCRIPTION

SCRAP PREPARATION

CONTI CASTER

LMFLadle Refining Station

EAF

SCRAP

ROUND STEELBLOOMSFormat 410 mm/ 16" 320 mm/ 12 1/2" 280 mm / 11" 250/ 10" 210 mm/ 8"Shape Round Round Round Round RoundWeight 1036 Kg/m ; 0.193 Lb/ft 631; 0.117 Lb/ft 483; 0.090 Lb/ft 3 85; 0.071 Lb/ft 272; 0.050 Lb/ftDiameter Tolerance (%) <1.5 <1.5 <1.5 <1.5 <1.5Ovality (%) <2 <2 <1.5 <1 <1Length Tolerance (+-) 4 mm/ 0.157 inch 4 mm/ 0.157 inch 4 mm/ 0.157 inch 4 mm/ 0.157 inch 4 mm/ 0.157 inchMinimum length (m) 3,25m / 10,66 Ft 3,25m / 10,66 Ft 3,25m / 10,66 Ft 3,25m / 10,66 Ft 3,25m / 10,66 FtMaximum Length (m) 5,25m / 17,22 Ft 5,25m / 17,22 Ft 5,25m / 17,22 Ft 5,25m / 17,22 Ft 5,25m / 17,22 FtStraightness (+-) 4 mm/ 0.157 inch 2 mm/ 0.078 inch 2 mm/ 0.078 inch 1,5 mm / 0.059 inch 1,5 mm / 0.059 inchEMS Stirring yes yes yes yes yes

API ASTM EN HRN DIN GOST BS NFA UNI LR CRS BV DNV C Mn P S Si Al Cu Sn A 179 P235TRI » .1212 St 37.4 3601 TUE 220 A Fe 35.2 Gr 320/P 360 360 HB TS 360 0,07 0,40 0,030 0,030 0,25 0,020 0,35 0,035 Gr. A S235JRH St 37.0 TU 37 A Fe 320/330 0,11 0,55 0,35 0,040 Gr. A S275J2H » .1214 St 35.8 10 360 TU37c Fe 360 Gr 360/B 360 360 HB TS 360 0,07 0,40 0,025 0,025 0,25 0,020 0,30 0,030 S275JOH 0,10 0,55 0,35 0,040Gr. B Gr. B P265TRI ».1213 St 44.4 CFS430 TUE 250 B Gr 410/P 410 410HB TS 420 0,13 0,75 0,025 0,025 0,25 0,020 0,30 0,030 St 44.0 Fe45-1 TS 410 0,16 0,90 0,35 0,040

4130 25 CrMo4 ».4730 25 CrMo4 30ChM 708A25 25CD4 25CrMo4 0,22 0,60 0,020 0,025 0,15 0,020 0,22 0,022 0,29 0,80 0,35 0,040

4140 42 CrMo4 ».4732 42 CrMo4 15142 CFS11 708A40 42CD4 0,39 0,60 0,025 0,025 0,15 0,002 0,25 0,025 0,44 0,80 0,35 0,040 ».3131 30 Mn 5 0,28 1,35 0,025 0,025 0,20 0,020 0,30 0,030

0,32 1,55 0,30 0,0401524 S355JOH ».3100 St 52.0 CFS5 TU52-b Fe490 0,17 1,20 0,025 0,025 0,25 0,020 0,30 0,030

S355J2H 0,20 1,40 0,35 0,040 ».8380 0,30 1,15 0,025 0,025 0,15 0,020 0,25 0,030 0,34 1,30 0,35 0,040 ».1402 0,27 0,75 0,025 0,025 0,20 0,020 0,30 0,030 0,33 0,90 0,30 0,040 0,27 1,10 0,025 0,025 0,20 0,200 0,30 0,030 Ë.0561 0,32 1,30 0,30 0,040 0,16 0,90 0,35 0,040Gr.6 410 HB 0,14 1,00 0,025 0,025 0,25 0,020 0,25 0,025 0,17 1,25 0,35 0,040X-42 410 HB 0,13 0,75 0,030 0,030 0,25 0,020 0,30 0,030 0,16 0,90 0,35 0,040X-52 510 HB 0,19 1,10 0,030 0,030 0,25 0,020 0,30 0,030 0,22 1,30 0,35 0,040J-55 0,32 0,85 0,025 0,025 0,25 0,020 0,25 0,030 0,38 1,05 0,35 0,040N-80 0,28 1,10 0,025 0,025 0,25 0,020 0,30 0,030 0,34 1,40 0,35 0,040H-40 0,16 0,90 0,025 0,025 0,25 0,020 0,30 0,030 0,21 1,10 0,35 0,040K-55 0,38 0,85 0,025 0,025 0,25 0,020 0,30 0,030 0,42 1,05 0,35 0,040K-55 V 0,27 1,10 0,025 0,025 0,25 0,020 0,30 0,030 0,32 1,30 0,35 0,040K-55 V (Coupling) 0,32 1,10 0,025 0,025 0,25 0,020 0,30 0,030

0,34 1,30 0,35 0,040

STEEL GRADES CHEMICAL COMPOSITIONIndicative values( %)

12

inch mm inch mm inch mm mm 0,188 4,80 4,784 1 ⁄2" 4.500 114,3 0,237 6,00 4" 4 114,3 6,02 0,337 8,60 8,56 0,188 4,80 4,78 0,219 5,60 5,566 5/8" 6.625 168,3 0,28 7,10 6" 6 168,3 7,11 0,375 9,50 9,53 0,432 11,00 10,97 0,25 6,400 6,35 0,277 7,000 7,048 5/8" 8.625 219,1 0,322 8,200 8" 8 219,1 8,18 0,5 12,700 12,70 6,35 0,25 6,400 7,8010 3⁄4" 10.750 273,1 0,307 7,800 10" 10 273 9,27 0,365 9,300 12,70 0,5 12,70 7,14 0,33 8,40 8,38 0,375 9,50 9,5312 3⁄4" 12.750 323,9 0,406 10,30 12" 12 323,8 10,31 0,5 12,70 12,70 0,625 15,90 15,88 0,312 7,90 7,92 0,375 9,50 9,5314" 14.000 355,6 0,406 10,30 14" 14 355,6 10,31 0,5 12,70 12,70 15,09 0,75 19,100 19,05

1.) Elbows according to ANSI/ASME B16.9/86From 1" up to 24" LR. STD. XS (to 180)

2.) Elbows produced with Hamburg process DIN 2609/91. DIN 2605-1/91From 21.3x2.0 to 610.0x12.5(to 180) R=1.5 DMade from Carbon Steel seamless pipes according to DIN 244/81.Quality: DIN1629/84, DIN

3.) Elbows R=3D. R=4DOut of standard produced with Hamburg process from 26.9x2.3 to273.0x6.3

4.) Concentric reduced according to DIN 2609/91.DIN 2616-2/91from 26.9 to 475.0mm all wall thickness.

5.) Concentric reduced according to ANSI B16.9 from 3⁄4" to 18"Material Quality- A 106 Gr.B- A 53 Gr.B

ELBOWS

PIPE DIMENSION PROGRAM FOR ELBOWSAPI 5 L

SIZE Outside diameter Wall Thickness SIZE Outside diameter Wall Thickness

ASTM A 106

PRODUCTION PROGRAMFOR ELBOWS

13

CMC Sisak d.o.o is a distributor of Elbows produced by "Metaflex" d.o.o.

Basic commitment of our business policy and strategy of developingCMC Sisak d.o.o. is production and delivery of round steel blooms andseamless pipes in quality which is recognized on the market andrepresents main element of differentiation against competitionand the foundation of market brand of CMC Sisak d.o.o. .

- maintaining and obtaining all needed certificates for our products andquality system

- uncompromising implementation of all quality management system elements by all employees

- continuous quality improvement of our products and quality management system

- special emphasis on workplace safety and environmental protectiontogether with equal treatment to all employees

- profitable way of thinking at all levels of organization

QUALITY

QUALITY POLICY

14

All certificates are available at www.cmccroatia.com

OUR COMMITMENTINCLUDES:

The company management will periodically review the implementation of quality policies, and if needed harmonise it with business policies,as well as take appropriate actions with the purpose of constant improvement of the processes effectiveness in the quality management system.

David MunroSales directorPh: +41 41 766 9633Mob: +41 79 222 0445e-mail:david.munro@cmc.com

Mario PlazibatCommercial directorPh.+385 44 565 225Fax:+385 44 565 624e-mail:mario.plazibat.cmc.com

Brankica ©urlanSales director for South East EuropePh:+385 44 565 474Fax:+385 44 538 624Mob:+385 99 5072 714e-mail:brankica.surlan@cmc.com

Marijana HalerIn-house product managerPh:+385 44 565 250Fax:+385 44 565 161Mob:+385 99 312 6540e-mail:marijana.haler@cmc.com

Elza BriπevacDeputy Sales ManagerCommercial department forSeamless pipes/ exportPh: + 385 44 565 483Fax: + 385 44 538 840Mob:+385 99 2183 506e-mail: elza.brisevac@cmc.com

Tomislav SmrekarDeputy marketing managerPh: +385 44 565 239Fax: +385 538 649Mob: +385 99 22 99 574e-mail:tomislav.smrekar@cmc.com

CONTACTS

15

www.cmccroatia.comwww.cmceu.comwww.cmc.com

Zagreb

SISAKRijeka

Osijek

Split

Dubrovnik

Croatia