CNC TIRE CONTAINER MOLD

5-AXIS MACHINING CENTER

(-20/+75 Degree TABLE Tilting)

ISTC-160HV with FANUC-0iMD Controller

------------------------------------------------------- 1 -------------------------------

♣ Machine Specification

1. CUTTING CAPACITY 1) Working table diameter --------------------------------------------------------- Ø 1,750 mm 2) Max. swing diameter ---------------------------------------------------------------- Ø 2,000 mm 3) Distance between table top Vertical head spindle end ----------------------- 1,200 mm

4) Max. load on table --------------------------------------------------------------- 2,000 kg

2. Spindle & Angle head 1) Type of spindle taper hole -------------------------------------------------------- ISO NO. 50

2) Spindle speed range --------------------------------------------------------------- 1,800 rpm

3) Spindle bearing inner diameter -------------------------------------------------- 100mm

4) Type of spindle of spindle -------------------------------------------------------- H+V Spindle

3. AUTOMATIC TOOL CHANGE

1) Magazine capacity/ Vertical+ Horizontal) ---------------------------------------- 30 sets

2) Max. tool weight --------------------------------------------------------------- 25 kg

3) Max. tool length -------------------------------------------------------------- 350mm

4) Type of retation knob ------------------------------------------------------------ MAS P50-1(45˚)

4. Travel, RAPID, CUTTING FEED 1) Axis Travel X/Y/Z ------------------------------------------------------- 2,400/1,800/1,250 mm

B-axis(Tilting Degree) ----------------------------------------- 75~-25 degree

C-axis (Rotating) ---------------------------------------- 360 degree 2) Rapid travel of

X-axis ------------------------------------------------------------ 10,000 mm/min Y / Z-axis -------------------------------------------------------- 10,000 mm/min

B-axis ------------------------------------------------------------ 0.5 rpm

C-axis(Table speed) -------------------------------------------- 2 rpm

3) Cutting feed ------------------------------------------------------------------- 1~3000 mm/min

5. Table (C-AXIS INDEX) 1) C-Axis indexing degree of an angle ----------------------------------------- 360degree

Indexing degree of an angle accuracy : ±3.5”

Indexing table division : 0,001 degree

-------------------------------------------------------- 2 -------------------------------

6. Main Motor, Servo Motors 1) Main Spindle Motor/FANUC -------------------------------------------------------------- 22/26 kw

2) X-axis servo motor ------------------------------------------------------------------------ AC 6.0 kw 3) Z-axis servo motor ------------------------------------------------------------------------ AC 6.0B kw

4) C-axis servo motor ------------------------------------------------------------------------ AC 4.0 kw

5) B-axis servo motor ------------------------------------------------------------------------ AC 4.0 kw

6) Hydraulic Motor/Built-in Motor ---------------------------------------------------------- 2.2 kw

7. OVERALL DIMENSIONS : APPROXIMATELY 1) Max overall height ------------------------------------------------------------------ 4,620 mm 2) Floor space /width x depth ------------------------------------------------------------ 5,600 x 5,200 mm 3) Machine weight -------------------------------------------------------------------------- 26,000 kg

8. POWER SOURCE 1) MAIN POWER: 220V 60Hz 3φ

2) TOTAL POWER CAPACITY : 60KVA

9. CNC SPECIFICATION 1) Maker : FANUC

2) Type : FANUC- 0iMD

♣ Standard Accessories

• Hydraulic Tank -------------------------------------------------------------- 1 set

• Work Light /40w ------------------------------------------------------------ 1 pc

• Leveling Bolt & Block ------------------------------------------------------ 1 set

• Chip Cover Open Type ---------------------------------------------------- 1 set

• Patrol Lamp:3 steps- yellow, green, red -------------------------------- 1 set

• Automatic power off ------------------------------------------------------- 1 set

• Rotating type control panel ------------------------------------------------------- 1 set

• X-axis sliding Cover: R,L ------------------------------------------------- 1 set

• Automatic Oil & Grease for sliding surfaces -------------------------- 1 set

• Chip Conveyor (Hinge belt type) ------------------------------------------ 1 set

• Coolant Equipment ---------------------------------------------------------- 1 set

• Tools Change (Horizontal, Vertical) -------------------------- To hand manual

• Full Sets Of Operation Manual Books ------------------------------------- 1 set

• FANUC Controller Operation, Maintenance Manual Books ------------- 1 set

------------------------------------------------------- 3 -------------------------------

TIRE MOLD CONTAINER MACHINING CENTER (TABLE TILTING Degree 75~-20)

------------------------------------------------------- 4 -------------------------------

------------------------------------------------------- 5 -------------------------------

HEAD HORIZENTAL+VERTICAL TYPE

------------------------------------------------------- 6 -------------------------------

TIRE MODL LETTERING, CONTAINER MOLD

------------------------------------------------------- 7 -------------------------------