Code : STM#120 Samsung Electronics Co., Ltd. OfficeServ 7200 Hardware Description Distribution...

Code : STM#120Code : STM#120

Samsung Electronics Co., Ltd.

OfficeServ 7200 Hardware DescriptionOfficeServ 7200 Hardware Description

Distribution

EnglishED01

© Samsung Electronics Co., Ltd. 2

ContentsContents

Cabinet and Power Supply Cabinet and Power Supply

Processor ModulesProcessor Modules

Voice Trunk ModulesVoice Trunk Modules

Subscriber StationsSubscriber Stations

Data ModulesData Modules

TerminalsTerminals


Cabinet and Power SupplyCabinet and Power Supply


Cabinet ConfigurationCabinet Configuration

MCP only8TRK,DLI,SLI,HYBWLI,MGI,WIM,4DSL

8TRK,DLI,SLI,HYBWLI,MGI,LIM,4DSL

8TRK,DLI,SLI,HYB,LIMTEPRI,WLI,MGI,4DSL



LCP only8TRK,DLI,SLI,HYBWLI,MGI,WIM,4DSL

8TRK,DLI,SLI,HYBWLI,MGI,LIM,4DSL


8TRK,DLI,SLI,HYB,LIMWLI,MGI,4DSL

8TRK,DLI,SLI,HYB,LIMWLI,MGI,4DSL

Expansion Cabinet

Access Cabinet


continuecontinue

Rear Side Configuration of Cabinet Function

External Rectifier Socket External DC power supply socket for PoE.

Power Switch Turn on/off the OfficeServ 7200 power.

Power Connection Connector between Basic Cabinet and Extension Cabinet

The connector to supply the supplied power to the external cabinet.

Power Input/Output Connector The connector to connect power cable.

AC LED LED is turned on when AC power is entered.

DC LED LED is turned on when DC power is properly output.

Battery Connection Socket The socket to connect the external battery.


PSU (Power Supply Unit)PSU (Power Supply Unit)

Features1 PSU per chassis

Mounted on back plane

Supports 80 devices per chassis

Power is controlled by a thermal sensor

After 24hrs of cooling fan failure, PSU will stop !


Processor BoardsProcessor Boards


MFM

RCM

MIS

MCP (Main Control Unit)MCP (Main Control Unit)

FeaturesInstalled in slot 0 of main chassis

256 time slot switch matrix

1x smart media card slot

3x daughter module positions

Memory backup switch

8 position DIP switch

1x internal MOH source• MFM : Multi-Frequency Module • RCM/RCM2 : R2 CID Module• MIS : Miscellaneous


continuecontinue

Capacity without Option board

Capacity with Option board

Items Specification

No. of DTMF sender

No. of DTMF receiver 4 channels

Items No. of channel

No. of DTMF sender Non limit

No. of DTMF receiver 16 channels

No. of R2/CID receiver 14 channels

No. of R2 sender 29 channels

Items No. of channel

External music on hold 2 channels

Internal music on hold 1 channel

External page 1 channel

External loud bell 1 channel

External page dry contact 2 channels

Common dry contact 1 channel


DIP SWITCH USE on the OS7200 MCP

ON (left) OFF (right)

4 Digit Trunk Numbers SW8 3 Digit Trunk Numbers

4 Digit Station Groups SW7 3 Digit Station Groups

4 Digit Station Numbers SW6 3 Digit Station Numbers

SW5 Reserved

Country Select SW4 Country Select



Country Select SW 1 Country Select

4 3 2 1 Country

OFF OFF OFF OFF Korea

OFF OFF OFF ON USA

OFF OFF ON OFF UK

OFF OFF ON ON Italy

OFF ON OFF OFF Australia

OFF ON OFF ON New Zealand

OFF ON ON OFF Holland

OFF ON ON ON Denmark

continuecontinue

Sets DIP switch

S3

S2

CHARGEOff


continuecontinue

Front View

Ports & LEDs Function Description

LINK1~LINK3 Ports that connect the MCP with the LCP.

MISC1~MISC2 Ports that connect external music sources, paging device, loud bell, common bell, or door bell.

SmartMedia Port for installing the NAND-type flash memory.

LAN Port for establishing the 10/100 BASE-T Ethernet connection.

SIO UART port (for tests).

RST Button for resetting the MCP board.

RUN LED- Off: Power is not connected.- On: Booting- Blink: The Program is operating properly

LAN LED- Off: MCP is not connected to LAN.- On: MCP is connected LAN.- Blink: MCP is transmitting or receiving Data through LAN port.

SM LED- Off: The Smartmedia is not installed.- On: The SmartMedia is installed, however is not accessed.- Blink: The SmartMedia is installed and is being accessed.

LCP LED- Off: There’s no message exchange between MCP and LCP.- On: Messages are being sent/received to/from the LCP.


Daughter boards for MCPDaughter boards for MCP

MFM (Multi-Frequency Module)Installed in any position on MCP module

Only 1 per system

12 DSPs for DTMF and tone detection


continuecontinue

RCM (R2 CID Module)Installed on MCP module

Only 1 per system

RCM1R2 signalling send (30 channels) and receive (8 channels) or CID

detection (14 channels) by DIP switch on RCM.

RCM2R2 signalling send ( channels) and receive (8 channels) or CID detection

(14 channels) by DIP switch on RCM.


continuecontinue

MISC (Miscellaneous)Installed on MCP

Only 1 per system

2x external MOH

1x external page

1x loud bell

1x common bell

1x dry contact


continuecontinue

Dry contact #1(For common bell)

Dry contact #3(For external page)

External Page Equipment

Additional Page Equipment

MISC 1

MISC 2

Dry contact #2(For external page)


LCP (Local Control Processor)LCP (Local Control Processor)

FeaturesInstalled in slot 0 expansion chassis

3x link cable RJ45 ports, for connection to MCP

2x status LEDs


continuecontinue

Front View

Ports & LEDs Function

LINK1~LINK3 Ports that connect the MCP with the LCP.

SIO UART port(for tests).

RST Button for resetting the LCP board.

RUN LED This LED indicates the status of the LCP.- Off: Power is not connected.- On: Booting.- Blinking: Program in operation.

MCP LED This LED indicates the status of signaling message processing. - Off: There’s no message exchange between MCP and LCP.- On: Messages are being sent/received to/from the MCP.


Voice Trunk ModulesVoice Trunk Modules


Voice Trunk Module (TEPRI)Voice Trunk Module (TEPRI)

FeaturesSame as OS500 operation.

Only installed in slots 3 – 5 of Access cabinet or slot 3 of Expansion cabinet.

T1/E1 signals by programming.

Resistor Terminations for T1 line(100 W) and E1 line(120 W).

8 position DIP switch.


continuecontinue

DIP switch SettingTEPRI Module DIP SWITCH Settings

Switch No. ON OFF Description

1 T1 E1 Selects whether T1 or E1

2 PRI T1 or E1 Selects whether PRI or not

3 Not used

4 NETWORK USER Select Network or User

5 Not used

6 Not used

7 Not used

8 Always ON This switch must always be ON as it is used for Card ID

Switch Settings for PRI/E1 operation

Switch No. PRI Operation E1 Operation 1 OFF OFF 2 ON OFF 3 OFF OFF 4 OFF ON for Master OFF for

Slave (Note) 5 OFF OFF 6 OFF OFF 7 OFF OFF 8 ON ON

Note: When networking OS7200 systems one system must be designated the master (NETWORK) and the other the slave(USER)


continuecontinue

Front ViewRST

TEPRI

T1/E1/PRI SIO

SYNC ASI IPC TP1

LOS L2 CLK TP2


T1/E1/PRI Ports that connect the T1/E1/PRI cable.


RST Button for resetting the TEPRI board.

SYNC LED - On: Clocks are not synchronized when they interwork with the counterpart station.- Off: Clocks are synchronized when they interwork with the counterpart station.

LOS LED - On: Signals have been lost.- Off: Signals have not been lost.

AIS LED - On: The remote alarm has been generated.- Off: The remote alarm has not been generated.

L2 LED - On: The PRI Layer2 is operating properly. - Off: The PRI Layer2 is operating abnormally.

IPC LED - On: The board is interworking with the MCP/LCP.- Off: The board is not interworking with the MCP/LCP.

CLK LED - On: The board has received the synchronization clock from the counterpart station.- Off: Using synchronous clock for internal clock.

TP1 LED - This LED turns on once the T1 is established.

TP2 LED - This LED turns on once the PRI is connected.


Voice Trunk Module (8TRK)Voice Trunk Module (8TRK)

Features8 trunk loop start module

8 caller ID path support

Performs Polarity Reverse Sensing (PRS), (Option)

Performs Metering Pulse Detection (MPD), (Option)


continuecontinue

Pin Assignment

P1-P8 Port(RJ-45)(RJ-45)

Pin No. 1 2 3 4 5 6 7 8

Function - - - C.O. TIP C.O. RING - - -


continuecontinue

Front View

8TRK

P1

P5

P2

P6

P3

P7

P4

P8

P1

P5

P2

P6

P3

P7

P4

P8


P1~P8 Trunk ports.

P1~P8 LED These LEDs indicate the status of the ports.- Off: The trunk line is not being used.- On: The trunk line is being used.- Blink: The ring is being connected.


Voice Trunk Module (4BRI)Voice Trunk Module (4BRI)

Features8 ISND2 channels

Slots 1 – 5 of any cabinet

Max 10 cards – 80 channels


continuecontinue

Front View

4BRI

P1-T

RUN

P2-T P3-T P4-T

P1-S P2-S P3-S P4-S

ACT


P1-T~P4-T Office (trunk) Port

P1-S~P4-S Internal (station) Port

RUN LED 4BRI Board Operation Status- Off: 4BRI board is abnormal or power is disconnected- On: 4BRI board is properly operated.

ACT LED 4BRI Board LAYER1 SETUP Status- Off: LAYER1 SETUP Abnormal- On: LAYER1 SETUP Normal


MGI (Media Gateway Interface)MGI (Media Gateway Interface)

FeaturesMGI2 – carrier module has NO MGI channels

MGI2 daughter modules added to provide 4 – 16 channels.

Installed in any subscriber slot.

G.729,G.723.G.726.G.711


continuecontinue

Option boardOption board provide 4 channels.

Option4

MGI2D

Option3

MGI2D

Option2

MGI2D

Option1

MGI2D


Subscriber StationsSubscriber Stations


Analog Station (8/16SLI)Analog Station (8/16SLI)

FeaturesSLI (Subscriber Line Interface)

FunctionsRing generationDTMF/Dial pulse detectionHook on/off detectionTone generation

Board types8 SLI : 8 SLI ports16 SLI : 16 SLI ports16 MWSLI : 16 SLI with message wait

Power fail transfer relays


continuecontinue

Front View

8SLI

P1

P5

P2

P6

P3

P7

P4

P8

P1

P5

P2

P6

P3

P7

P4

P8


P1~P8 Station ports for analog phones.

P1~P8 LED orP1~P16 LED

These LEDs indicate the operation status of the ports.- Off: The station is not being serviced.- On: The station is being serviced.

16SLI

P1/P9 P1P9

P2/P10 P3/P111

P4/P12

P5/P13 P6/P14 P7/P15 P8/P16

P2P10

P3P11

P4P12

P5P13

P6P14

P7P15

P8P16


continuecontinue

Pin Assignment

Pin No. 1 2 3 4 5 6 7 8

Function PFT TIP

PFT RING

- SLI 1 TIP

SLI 1 RING

-

Pin No. 1 2 3 4 5 6 7 8

Function - - - SLI 2 TIP

SLI 2 RING

-

P1 port

Ports from P2 to P8


Digital Station (8/16DLI)Digital Station (8/16DLI)

FeaturesDLI (Digital Line Interface)

Types8 DLI : 8 DLI ports 2B+D16 DLI : 16 DLI ports 1B+D

Max 8 large display phones per module


continuecontinue

Front View

8DLI

P1

P5

P2

P6

P3

P7

P4

P8

P1

P5

P2

P6

P3

P7

P4

P8

16DLI

P1/P9 P1P9

P2/P10 P3/P11 P4/P12

P5/P13 P6/P14 P7/P15 P8/P16

P2P10

P3P11

P4P12

P5P13

P6P14

P7P15

P8P16


P1~P8 orP1~P16

Station ports of Samsung digital phones.

P1~P8 orP1~P16 LED

These LEDs indicate the status of the ports.- Off: The station is not being used.- On: The station is being used.If the LED turns green, it shows that the P1-P8 is being used.If the LED turns red, it shows that the P9-P16 is being used. If the LED turns yellow, it shows that both of the ports are being used simultaneously.


continuecontinue

Pin Assignment

Pin No. 1 2 3 4 5 6 7 8

Function - - - DLI 1 DLI 1 -


Hybrid Station (8HYB/8Combo)Hybrid Station (8HYB/8Combo)

FeaturesRing generation

DTMF/Dial pulse detection

Hook on/off detection

Tone generation

Specifications 8 SLI ports

8 DLI ports


continuecontinue

Front View

8HYB

P1/P9 P1P9

P2/P10 P3/P11 P4/P12

P5/P13 P6/P14 P7/P15 P8/P16

P2P10

P3P11

P4P12

P5P13

P6P14

P7P15

P8P16


P1~P16(8HYB)P1~P16(8COMBO)

Station ports of Samsung digital phones.

P1~P16 LED(8HYB)

These LEDs indicate the status of the ports.- Off: The station is not being used.- On: The station is being used.If the LED turns green, it shows that the P1-P8 is being used(Analog phone port).If the LED turns red, it shows that the P9-P16 is being used(Samsung digital phone port). If the LED turns yellow, it shows that both of the ports are being used while being connected to an analog phone and Samsung digital phone simultaneously.


continuecontinue

Pin Assignment

Pin No. 1 2 3 4 5 6 7 8

Function - - - SLI 1 TIP/DLI

SLI 1 RING/DLI

-


Voice Mail System (SVMi-20E)Voice Mail System (SVMi-20E)

FeaturesSame position rules as station modules

Default card has 4 ports

Scalable to 20 ports?

Modem daughter card (and yes, it works!)


continuecontinue

Front ViewLAN SIO

VM1 VM2 VM3 HDD

LAT LRT SDN PGD

SVMi-20E

RST

Part Description

LAN Interface Connector The LAN interface connector is used for data transmission and database backup. It is also called as ‘LAN connector’ and mainly used for system file transmission (backup and restore)SVMi-20E backs up or restores data by using LAN provided by customer or by connecting to laptop computer or PC connected the relevant LAN connector.

Serial Interface Connector Used to connect to PC.

Reset Button(RST) If pushing this button, SVMi-20E system starts and the call in progress is disconnected.

LED(Light Emitting Diode)

VM1 When one or more ports are hooked on/off in the first 4 ports(1~4), it blinks.

VM2 When one or more ports are hooked on/off in the second 4 ports (5~8), it blinks.

VM3 When one or more ports are hooked on/off in the final 4 ports(9~12), it blinks.

HDD If accessing to the hard disk driver, LCD blinks.

LAT When the LAN port is run, LED is turned on into green color.

LRT When transmitting data to LAN, LED is turned on into orange color.

SDN This LED displays the system status. When the system driver is loaded, LED is turned on into red color, and if the loading is terminated, LED is turned into green color.

PGD If the system power is normal, LED is turned on into green color.


Data ModulesData Modules


Router Module (WIM)Router Module (WIM)

FeaturesWIM : WAN Interface Module

FunctionsOnly 1 per systemOnly installed in slot 1 of main chassis1x LAN port2x WAN ports (RJ45)1x WAN port (V.35 serial)1x DMZSIO for configurationWIMD – daughter board for VPN


continuecontinue

Front View

WIM

DMZ

WAN1

LAN

WAN2

SIO

SERIAL

RUN DMZ LAN

SERIALL

WAN1

WAN2

RST


DMZ Internal port that does not need firewalls

LAN Ethernet port connected with the Intranet

SERIAL Port that connects the serial dedicated line that interworks with the V.35

WAN1, WAN2 WAN interface port that interworks with Ethernet of 10/100 BASE-T

SIO UART port(for tests)

RST Button for resetting the WIM module

RUN LED - Off: The WIM board is in an abnormal status or the power is not being supplied.- On: The WIM board is operating properly.

DMZ LED - Off: The link is not connected.- On: The link is operating.

SERIAL LED - Off: The link is not connected.- On: The link is operating.

WAN1, WAN2 LED - Off: The link is not connected.- On: The link is operating.

LAN LED - Off: Link is not connected- On: Link is in operation


continuecontinue

WIM to LIM connection

Using the Ethernet port of the front panel,

Through back panel, connect with the LIM board of slot 2.

The Method of LAN port connection• Managed LIM : Slot2 LIM with WIM• Unmanaged LIM : Slot 3,4,5


Switch Module (LIM/PLIM)Switch Module (LIM/PLIM)

LIM : LAN Interface Module

FeaturesInstalled in slots 2 ~ 5 of any chassis

Max 8 per system (128 ports)

When in slot 2 of main chassis it’s a managed switch

If in any other slot it’s unmanaged

16x 10/100 base T Ethernet ports

PLIM provides the Power over Ethernet (PoE) function

FunctionsDetects 10/100 BASE-T, or full/half duplex automatically.

Offers the VLAN for supporting QoS.

Functions as a switching hub.


continuecontinue

Front View

LIM

P1

P5

P2

P6

P3

P7

P4

P8

P9

P13

P10

P14

P11

P15

P12

P16


P1~P16 Ports for connecting the Ethernet.

Left LED of each port The LED indicates if the link is operating.- Blink: The link is operating.

Right LED of each port The LED indicates if the port of 10/100 BASE-T is operating.- Off: The port of 10 BASE-T is operating.- On: The port of 100 BASE-Tx is operating.


Wireless ModulesWireless Modules


Voice Application Module (4WLI)Voice Application Module (4WLI)

WLI : Wireless Line Interface

Features

FunctionsVoice decompression: G.711, G.729

Wireless specification: 802.11b WLAN

SpecificationsUp to four APs.

Simultaneous calling through up to four channels per AP.

The maximum number of mobile station subscribers is 120.


continuecontinue

Front View

4WLI

P1 P2 P3 P4

RUN

SW1 SW2 SW3

SIO


P1~P4 Port that connects with the WBS24.


RUN LED This LED turns on when the wireless LAN operates.

SW1~SW3 LED This LED turns on when the software task operates.


TerminalsTerminals


Digital PhonesDigital Phones

DS-24SE

DS2000 Series

DS-3020S

DS4000 Series DS5000 Series

DS-5012L

DS-5038D

DS-5014D

DS-5021D


IP PhonesIP Phones

ITP5000 Series

ITP-5012L

ITP-5021D

ITP-5014D

ITP5100 Series

ITP-5107S

ITP-5114D

ITP-5121D

ITP-5112L


AP (Access Point)AP (Access Point)

ConfigurationWBS24 Basic

WBS24 Combo

WIP PhoneWIP Phone

PDASoftPhone

Laptop PC

MGIMCP LIM

WIM LIM

RJ45 RJ11

AC POWER

LIM-MGI

PC

WIP PhoneWIP Phone

PDASoftPhone

Laptop PC

MCP WLI

WIM PLIM

RJ45 RJ11

WLI PC

RJ45

LIMCoverage = 30m

Data

Data


WLAN PhonesWLAN Phones

Configuration


Add on ModuleAdd on Module

FeaturesStation module type of digital phone where the programmable buttons and LEDs are expanded.

AOM Types Connectable Phones

DS-5064B AOM DS-5000 series digital phone

DS-4014 AOM DS-4000 series digital phone

DS-4064 AOM

DS-24SE AOM DS-24SE digital phone

DS-2024E AOM DS-2000 series digital phone

DS-3020S AOM DS-3000 series digital phone


Door Phone Interface ModuleDoor Phone Interface Module

FeaturesDoor Phone Interface Module (DPIM) connects door phones and door open/close devices with the OfficeServ 7200.


KDB-D/SKDB-D/S

FeaturesThe KDB-D module is attached to the digital phones connected with the DLI board for use.

The KDB-D enables a digital terminal to use one out of the two B channels received by another digital phone from the DLI board.

Samsung Electronics Co., Ltd.

Date post:	12-Jan-2016
Category:	Documents
Upload:	lambert-oneal
View:	235 times
Download:	14 times

Code : STM#120 Samsung Electronics Co., Ltd. OfficeServ 7200 Hardware Description Distribution...

Documents